advertisement
▼
Scroll to page 2
of 27
Digital Surround AV Receiver System AV-R700 Instruction Manual ELECTRONICS AH68-01597B Safety Warnings CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE REAR COVER. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CLASS 1 LASER PRODUCT This Compact Disc player is classified as a CLASS 1 LASER product. PREPARATION CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN Precautions This symbol indicates that dangerous voltage which can cause electric shock is present inside this unit. This symbol alerts you to important operating and maintenance instructions accompanying the unit. WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. Ensure that the AC power supply in your house complies with the identification sticker located on the back of your player. Install your player horizontally, on a suitable base (furniture), with enough space around it for ventilation (3~4inches). Make sure the ventilation slots are not covered. Do not stack anything on top of the player. Do not place the player on amplifiers or other equipment which may become hot. Before moving the player, ensure the disc tray is empty. This player is designed for continuous use. Switching off the DVD player to the stand-by mode does not disconnect the electrical supply. In order to disconnect the player completely from the power supply, remove the main plug from the wall outlet, especially when left unused for a long period of time. Wiring the Main Power Supply Plug(UK Only) IMPORTANT NOTICE The main lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated on the pin face of the plug and if it requires replacing, a fuse approved to BS1362 of the same rating must be used. Never use the plug with the fuse cover removed. If the cover is detachable and a replacement is required, it must be of the same colour as the fuse fitted in the plug. Replacement covers are available from your dealer. If the fitted plug is not suitable for the power points in your house or the cable is not long enough to reach a power point, you should obtain a suitable safety approved extension lead or consult your dealer for assistance. However, if there is no alternative to cutting off the plug, remove the fuse and then safely dispose of the plug. Do not connect the plug to a main socket as there is a risk of shock hazard from the bared flexible cord. Never attempt to insert bare wires directly into a main socket. A plug and fuse must be used at all times. During thunderstorms, disconnect AC main plug from the wall outlet. Voltage peaks due to lightning could damage the unit. Do not expose the unit to direct sunlight or other heat sources. This could lead to overheating and malfunction of the unit. Protect the player from moisture(i.e. vases) , and excess heat(e.g.fireplace) or equipment creating strong magnetic or electric fields (i.e.speakers...). Disconnect the power cable from the AC supply if the player malfunctions. Your player is not intended for industrial use. Use of this product is for personal use only. Condensation may occur if your player or disc have been stored in cold temperatures. If transporting the player during the winter, wait approximately 2 hours until the unit has reached room temperature before using. The battery used with this product contain chemicals that are harmful to the environment. Do not dispose of batteries in the general household IMPORTANT The wires in the main lead are coloured in accordance with the following code:– BLUE = NEUTRAL BROWN = LIVE As these colours may not correspond to the coloured markings identifying the terminals in your plug, proceed as follows:– The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK. The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED. WARNING: DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL WHICH IS MARKED WITH THE LETTER E OR BY THE EARTH SYMBOL , OR COLOURED GREEN OR GREEN AND YELLOW. 1 trash. 2 Features Contents √√ What is AV receiver? √√ Let's find out difference between general amplifier and AV receiver! General Amplifier AV Receiver 2 channels (left speaker and right speaker) Multiple Channel (5.1 channel by default) Play back music mainly Play back music and video sound realistically No decoder Has decoder Not play back various kinds of sound formats Play back various kinds of sound formats including Dolby Digital and DTS Many input/output connectors No noise using digital signal type Dolby Pro Logic ll x DTS (Digital Theater Systems) Dolby Pro Logic ll x is a new type of multiple channel audio signal decoding method that improves upon existing Dolby Pro Logic. DTS play backs 5.1 channel sound of wide-range by playing sound of DVD and CD disk as surround sound system. DTS 96/24 DTS-ES DTS is the surround format implementing 5.1 channel multi channel sounds of 96KHz/24bit without losing the image quality of DVD. In addition, it can reproduce the matrix 6.1 of DTS 96/24 decoder signal. DTS-ES is the surround format implementing surround type of discrete 6.1 channel while preserving upper compatibility in response to existing DTS Digital Sound format. It is the latest digital sound format maximizing the space quality and 360 surround experience by adding rear center channels. DOLBY DIGITAL EX DTS It not only significantly enhances space expression capability of surround channel but also easily implements the sound localization at the rear according to sound field reproduction at 6.1 channel including rear center channel. It reproduces the digital PCM or analog stereo sound source in 6.1 channels using the high precision digital matrix of DTS only. PREPARATION PREPARATION It refers to home theater exclusive amplifier by amplifying the audio signal from DVD and CD player as a core element of home theater. Safety Warnings ..............................................................................................................1 Precautions......................................................................................................................2 Features ..........................................................................................................................3 Contents ..........................................................................................................................4 Description ......................................................................................................................5 CONNECTIONS Connecting the Speakers ...............................................................................................9 Connecting External Components ..................................................................................11 Connecting External Component.....................................................................................13 Connecting the FM Antenna............................................................................................14 OPERATION Before Using AV Receivera .............................................................................................15 Selecting External Component Input ...............................................................................16 Setting the Speakera .......................................................................................................17 Setting DRC (Dynamic Range Compression) .................................................................21 Test Tone ........................................................................................................................22 Setting Speaker Level .....................................................................................................25 Dolby Pro Logic ll x Mode................................................................................................27 Dolby Pro Logic ll x Effect................................................................................................29 NEO:6 Mode....................................................................................................................31 SFE Mode........................................................................................................................33 EX/ES Mode ....................................................................................................................35 Stereo Mode ....................................................................................................................37 RADIO OPERATION Listening to Radio ...........................................................................................................39 Presetting Radio Stations ...............................................................................................40 About RDS Broadcating ..................................................................................................41 MISCELLANEOUS Manufactured under license from Dolby Laboratories. “Dolby”, “ProLogic” and double-D symbol are the trademark of Dolby Laboratories. Confidential unpublished works (c)1992-1997 Dolby Laboratories. All rights are Reserved. 3 This product is manufactured with technical cooperation with Digital Theater Systems, Inc., is the registered trademark of Digital Theater Systems. (c)1996 Digital Theater Systems, Inc. All rights Reserved. Convenient Functions .....................................................................................................43 Operating TV with Remote Control..................................................................................45 Operating VCR (DVD) with Remote Control....................................................................47 Before Calling for Service................................................................................................49 Specifications ..................................................................................................................51 Memo...............................................................................................................................52 4 Description HEADPHONE Jack POWER STANDBY Indicator POWER button INPUT button SURROUND button EXTERNAL AUDIO INPUT CONNECTOR EXTERNAL VIDEO INPUT CONNECTOR REMOTE CONTROL Sensor VOLUME CONTROL EXTERNAL OPTICAL DIGITAL AUDIO INPUT CONNECTOR SELECTION button TUNING ( , ) button SAT VIDEO INPUT AM ANTENNA 5.1 CH ANALOG CONNECTOR CONNECTOR AUDIO CONNECTOR DVD VIDEO INPUT FM ANTENNA CONNECTOR CONNECTOR CD COAXIAL DIGITAL AUDIO INPUT CONNECTOR SAT OPTICAL DIGITAL AUDIO INPUT CONNECTOR VCR VIDEO INPUT CONNECTOR VCR VIDEO OUTPUT CONNECTOR MONITOR VIDEO OUTPUT CONNECTOR DVD OPTICAL DIGITAL AUDIO INPUT CONNECTOR MONITOR S-VIDEO OUTPUT CONNECTOR VCR S-VIDEO OUTPUT CONNECTOR DTS ES 96/24 INDICATOR NEO:6 INDICATOR LIVE SURROUND INDICATOR L.PCM INDICATOR DOLBY DIGITAL EX INDICATOR MPEG2 INDICATOR S.W CENTER SPEAKER TERMINAL SAT S-VIDEO INPUT CONNECTOR VCR AUDIO INPUT CONNECTOR VCR AUDIO OUTPUT CONNECTOR DVD AUDIO INPUT CONNECTOR SUBWOOFER OUTPUT CONNECTOR 1 SAT AUDIO INPUT CONNECTOR SUBWOOFER OUTPUT CONNECTOR 2 COAXIAL DIGITAL INDICATOR OPTICAL DIGITAL INDICATOR REAR SPEAKER TERMINAL VCR S-VIDEO INPUT CONNECTOR CD AUDIO INPUT CONNECTOR SPEAKER INDICATOR COOLING PAN FRONT SPEAKER TERMINAL DVD S-VIDEO INPUT CONNECTOR OPTICAL DIGITAL AUDIO OUTPUT CONNECTOR [ Display ] PREPARATION [ Rear Panel ] [ Front Panel ] √√ Accessories œœ RADIO FREQUENCY INDICATOR ANALOG INDICATOR RADIO STEREO INDICATOR DOLBY PRO LOGIC SUBWOOFER IIX LEVEL INDICATOR VARIOUS INDICATOR FUNCTION INDICATOR RADIO BROADCASTING RECEIVING INDICATOR Remote Control AM Antenna USER’S GUIDE FM Antenna 5 Battery(AAA Size 1.5V) User’s Manual 6 Description POWER button TV/VIDEO, FUNCTION button SLEEP button TUNER button NEO : 6 button DISPLAY button MODE button PREPARATION [ Remote Control ] Insert Remote Batteries TV Indicator VCR Indicator AV RECEIVER Indicator DVD Indicator MODE button MO/ST button SUBWOOFER button SFE MODE button EX/ES button EFFECT button 1 Remove the battery cover on the back of the remote by pressing down and sliding the cover in the direction of the arrow. 2 Insert two 1.5V AAA batteries, paying attention to the correct polarities (+ and –). 3 Replace the battery cover. EXTERNAL DEVICE PLAYBACK button MUTE button VOLUME CONTROL button MENU button ANALOG/DIGITAL button TUNER MEMORY button TUNING/CHANNEL button SPEAKER LEVEL button STEREO button MOVE/SELECT button Caution ! Follow these precautions to avoid leaking or cracking batteries: • Place batteries in the remote control so they match the polarity:(+) to (+)and (–)to (–). • Use the correct type of batteries.Batteries that look similar may differ in voltage. • Always replace both batteries at the same time. • Do not expose batteries to heat or flame. Range of Operation of the Remote Control Direct Function Select button SPEAKER SETUP button TEST TONE button SPEAKER DISTANCE button Number(0~9) buttons 7 RDS Selection button The remote control can be used up to approximately 23 feet/7 meters in a straight line. It can also be operated at a horizontal angle of up to 30° from the remote control sensor. To open the remote control cover, push the top of the cover, then slide downward. 8 Connecting the Speakers Before moving or installing the product, be sure to turn off the power and disconnect the power cord. PASSIVE SUBWOOFER POWER AMPLIFIER FRONT (R) FRONT (L) REAR (R) REAR (L) ACTIVE SUBWOOFER (BUILT-IN POWER AMPLIFIER) CONNECTIONS MAIN UNIT AV-R700 SL SR SB CENTER Position of AV Receiver Rear Speakers • Place AV Receiver on the dedicated stand or chest of living room or under the TV stand properly. • Place the rear left and right speaker at the interval of front left and right speaker. • If there isn't enough now, place rear speakers to face down other. • Place the rear speakers about 70 cm to 1 m above your ear, facing slightly downwards. ❈ Unlike the front and center speakers, the rear speakers and used to mainly sound effects and sound will not come from them all the time. Front Speakers • Adjust the angle of front left and right speakers so that it can form 30 degree to the left and right from the listening position. • Place the speakers so that their tweeters will be at the same height as your ear. • Align the front face of the front speakers with the front face of the center speaker or place them slightly in front of the center speaker. Center Speaker • It is best to install center speaker at the same height as the front speakers. • You can also place center speaker directly over or under the TV. Subwoofer REAR CENTER √ Connecting Front Speaker Wire 1 Turn and loosen the speaker connector. 2 Insert the black wire into the black(-) terminal and the red wire into the red(+) terminal. 3 Turn and fasten the speaker connector. Rear Center Speaker • If you place 1 rear center speaker, place it so that it faces forward from the back of listener. • Place the rear center speaker about 70 cm to 1 m above rear speakers, facing slightly downwards. Caution! When you place the speaker on the wall, make sure to fasten it tightly so that it may not fall off. √ Connecting Center/Rear Speaker Wire 1 Press the tab of the speaker connector. 2 Insert the black wire into the black(-) terminal and the red wire into the red(+) terminal. Caution! • Never touch speaker terminals while the power is on. Doing so could result in electric shock. • Make sure the polarities (+ and -) are correctly. • The position of the subwoofer is not so critical. Place it anywhere you like. • Usually, it is placed by a corner near the front speakers. 9 10 Connecting External Components Connecting Video Component Before moving or installing the product, be sure to turn off the power and disconnect the power cord. Video Player Video Projector SAT Player AUDIO OUT VIDEO S-VIDEO OUT OUT S-VIDEO IN DIGITAL OUT AUDIO OUT R R VIDEO OUT CONNECTIONS DIGITAL OUT S-VIDEO OUT L L VIDEO IN S-VIDEO IN DIGITAL IN R L AUDIO OUT R L AUDIO IN VIDEO OUT IN S-VIDEO OUT IN MD Player DVD Player TV • If the Audio Output connector of external component is only 1, connect Audio Output connector or external component to either of Audio Input connector (right or left) of main unit. • Connect the red cable of audio cable to red connector and white cable to white connector. • When you connect Video Input connector of external component to Video Output connector of main unit, connect Video Input connector of external component either to Video Output connector or S-Video Output connector. Caution! 11 • Disconnect the power plug from the outlet if you do not use this unit for long period of time. 12 Connecting External Component Connecting Audio Component/ 5.1 Channel Before moving or installing the product, be sure to turn off the power and disconnect the power cord. Connecting the FM and AM Antennas If AM reception is poor, connect an outdoor AM antenna(not supplied). DIGITAL OUT AUDIO OUT R FM Antenna (supplied) L Snap the tabs on the loop into the slots of the base to assemble the AM loop antenna. FM antenna connection 1. Connect the FM antenna supplied to the FM 75ΩCOAXIAL terminal as a temporary mea-sure. 2. Slowly move the antenna wire around until you find a location where reception is good, then fasten it to a wall or other rigid surface. CENTER R L FRONT CONNECTIONS AM Loop Antenna (supplied) CD Player AM antenna connection 1. Connect the AM loop antenna supplied to the AM and terminals. 2. If reception is poor, connect an outdoor single vinylcovered wire to the AM ter-minal. (Keep the AM loop antenna con-nected). R L SUB SURR. WOOFER DVD or 5.1 Channel Player COOLING FAN The cooling fan dissipates the heat generated inside the unit so that the unit can be operated normally. The cooling fan is activated automatically to supply cool air to the unit. Please observe the following cautions for your safety. • Make sure the unit is well-ventilated. If the unit has poor ventilation, the temperature inside the unit could rise and may damage it. • Do not obstruct the cooling fan or ventilation holes. (If the cooling fan or ventilation holes are covered with a newspaper or cloth, heat may build up inside the unit and fire may result.) 13 14 Before Using AV Receiver To Select the Function Turning On/Off REMOTE CONTROL MAIN UNIT Method 1 Press the FUNCTION button. Press the FUNCTION button. 1 Connect the power plug to the outlet. the POWER ( ) button of the main unit. 2 Press This unit will be turned on or off. • Each time you press the this button, 5.1CH MULTI CH ➝ CD ➝ DVD ➝ SAT ➝ VCR ➝ AUX ➝ FM ➝ AM will be selected in turn. • Method 2 REMOTE CONTROL Press the POWER ( Selecting External Component Input ) button of the remote control while main unit is turned on. • This unit will be turned on or off. MAIN UNIT Press INPUT button. ) button of remote controller while main unit is turned off. • Each time you press the this button, 5.1CH MULTI CH ➝ CD ➝ DVD ➝ SAT ➝ VCR ➝ AUX ➝ FM ➝ AM will be selected in turn. • When you turn off the power by pressing the POWER ( ) button of remote control, this unit will be standby mode.To completely turn off the power, press the POWER ( ) button of the main unit. Standby indicator will be turned off. • When you select the audio external component (external component without Video Output connector), the image of video external component (external component with Video Output connector) used last will appear in the TV screen. • You can watch the image of video external component while listening to sound of Functions of Dedicated Remote Control You can operate TV, VCR, DVD, AV Receiver with one remote control. audio external component. To Select Analog/Digital Input You can listen ti sound in Analog 2 Channels or Dolby Digital 5.1 Channel using this unit. REMOTE CONTROL Press MODE button. • Each time you press this button, it will select and blink TV indicator ➝ VCR indicator ➝ DVD indicator ➝ AV Receiver indicator in turn. REMOTE CONTROL Press the ANALOG/DIGITAL button. • For DVD, SAT, AUX Function ANALOG and OPTICAL (1, 2, 3) will be selected repetitively. • You can operate TV after TV indicator blinking. You can operate VCR after VCR indicator blinking. You can operate DVD after DVD indicator blinking. You can operate AV Receiver after AV Receiver indicator blinking. • For CD Function ANALOG and COAXIAL will be selected repetitively. • Basic operation of remote control is set up based on Samsung products. Refer to page 45~48 for more details on operation method. To set the menu function of external component Press the MENU button. • Menu setup screen of TV, VCR and DVD Player will appear. 15 • You can enjoy Dolby Digital effect only if you connect Audio Output connector of external audio component to optical/coaxial digital Audio Input connector of main unit. Caution! • You can operate this function only with remote controller. • This function will be selected in analogue only for VCR function, and will not work for 5.1CH MULTI CH function. 16 OPERATION • This unit will not turned on or off even if you press the POWER ( Press DIRECT FUNCTION Select button. • You can directly select 5.1CH, VCR, DVD, CD, SAT, or AUX. Setting the Speaker Before moving or installing the product, be sure to turn off the power and disconnect the power cord.Signal outputs and frequency response from the speaker will automatically be adjusted according to your speaker configuration and whether certain speakers are used or not. √ REMOTE CONTROL SPK SEL. button to select the speaker you want. 1 Press Each time you press this button, F.SPK ➝ C.SPK ➝ S.SPK ➝ SB SPK ➝ • SW SPK ➝ CROVR ➝ SPK MODE OFF will be selected in turn. MAIN UNIT 2 Press …† button to set the speaker as you want. 3 Repeat the steps 1 and 2 to set the speaker. 1 Press and hold SURROUND button for about 5 seconds. • “SETUP MODE” appears on the display and enters into Setup Mode. SURROUND button to select the speaker you want. 3 Press Each time you press this button, F.SPK ➝ C.SPK ➝ S.SPK ➝ SB SPK ➝SW SPK ➝ CROVR will be selected in turn. 4 Press SELECT ( 5 ) button to set the speaker as you want. Repeat the steps 3 and 4 to set the speaker. To Exit Setup Mode To Exit Setup Mode • Wait for about 5 seconds or press the SPK SEL. button of the remote control to • Wait for about 5 seconds or turn the VOLUME CONTROL of the main unit. “SETUP MODE OFF” appears on the display and exits Setup Mode. select SPK MODE OFF. To Use SUBWOOFER button of Remote Control Press SUBWOOFER button. • Each time you press this button, SW SPK : YES, SW SPK : NO will be selected in turn. • If you play in 2 Channel Stereo, select 'YES' to use Subwoofer and 'NO' not to use. Caution! • If F.SPK is set to ‘SMALL’, SW SPK is fixed to ‘YES’. • If S.SPK is set to ‘NONE’, SB SPK is fixed to ‘NONE’. • You cannot use Speaker Setup Mode in 5.1CH MULTI CH function. 17 , Setting the Speaker • F.SPK (Front) : LARGE, SMALL • C.SPK (Center) : LARGE, SMALL, NONE • S.SPK (Rear) : LARGE, SMALL, NONE • SB SPK (Rear Center) : LARGE, SMALL, NONE • SW SPK (Subwoofer) : YES, NO • CROVR (Crossover Frequency): 40, 60, 80, 100, 120, 150,200Hz • LARGE : Select when you use large speaker. You can listen to full ranges of sound from bass to treble. • SMALL : Select this when you use small speaker. Bass below 100ß‘ will not be output from the whole speakers but only from subwoofer. • NONE : Select this when you use no speaker. • YES : Select this when you use Subwoofer Speaker if you play back in 2 Channel Stereo. • NO : Select when you do not use Subwoofer Speaker if you play back in 2 Channel Stereo. • CROVR: Select the crossover frequency depending on the size of speaker connected when you use subwoofer. Select 40Hz if cone paper speaker is 16cm, select 60Hz for 14cm, 80Hz for 12cm, 100Hz for 10cm, 12Hz for 8cm ,150Hz for 6cm and 200Hz for 4cm. 18 OPERATION INPUT button one time. 2 Press • “SPEAKER SETUP” appears in the display. Setting the Speaker √ REMOTE CONTROL 1 Press the SPEAKER DISTANCE button to select the speaker you want. MAIN UNIT • Each time you press this button, F.L ➝ CEN ➝ F.R ➝ S.R ➝ S.B ➝ S.L ➝ S.W ➝ DISTANCE OFF will be selected in turn. 2 Press …† button to set the speaker distance. and hold SURROUND button for about 5 seconds 1 Press “SETUP MODE” appears on the display and enters into Setup Mode. 2 Press INPUT button 2 times. • For F.L, CEN, F.R, S.W Speaker, you can set the distance from the speaker to • • “DISTANCE SETUP” appears on the display. 3 Repeat the steps 1 and 2 to set the speaker distance. SURROUND button to select the speaker you want. 3 Press Each time you press this button, F.L ➝ CEN ➝ F.R ➝ S.R ➝ S.B ➝ S.L ➝ S.W • will be selected in turn. SELECT( , ) button to set the speaker distance. 4 Press For F.L, CEN, F.R, S.W Speaker, you can set the distance from the speaker to OPERATION listening position between 0.0~1.5m at the interval of 0.3m. • For S. R, S.B, S.L Speaker, you can set the distance from the speaker to listening position between 0.0~4.5m at the interval of 0.3m. • listening position between 0.0~1.5m at the interval of 0.3m. • For S.R, S.B, S.L Speaker, you can set the distance from the speaker to listening position between 0.0~4.5m at the interval of 0.3m. 5 Repeat the steps 3 and 4 to set the speaker distance. To Exit Setup Mode • Wait for about 5 seconds or press the SPEAKER DISTANCE button of remote control To Exit Setup Mode to select DISTANCE OFF. • Wait for about 5 seconds or turn the VOLUME CONTROL of the main unit. “SETUP MODE OFF” appears on the display and exit Setup Mode. Setting Speaker Distance • If the listening position is beyond the range of speaker distance setup when you place the speaker, set the speaker distance to the maximum. 19 Set the distance from the speaker to listening position at the interval of 0.3m. • F.L (Front-Left) : 0ft 0.0m ~ 5ft 1.5m • CEN (Center) : 0ft 0.0m ~ 5ft 1.5m • F.R (Front-Right) : 0ft 0.0m ~ 5ft 1.5m • S.R (Rear-Right) : 0ft 0.0m ~ 15ft 4.5m • S.B (Rear Center): 0ft 0.0m ~ 15ft 4.5m • S.L (Rear-Left): 0ft 0.0m ~ 15ft 4.5m 20 Setting DRC (Dynamic Range Compression) Test Tone You can use this function to enjoy Dolby Digital sound when watching movies at low volume at night. Use test tine to check speaker connection status or defect of speaker or adjust the level. To Automatically Output Test Tone √ REMOTE CONTROL 1 Press TEST TONE button. √ • Test signal will be automatically output as follows; F.L ➝ CEN ➝ F.R ➝ S.R ➝ S.B ➝ S.L ➝ S.W. • During test tone output, press …† button to adjust the speaker output level MAIN UNIT from -10 to +10 dB by 1 step. OPERATION and hold SURROUND button for about 5 seconds. 1 Press “SETUP MODE” appears on the display and enters into Setup Mode. 2 Press INPUT button 3 times. • • “DRC SETUP” appears on the display. 3 Press SURROUND button to set DRC. • Each time you press this button, DRC : STD ➝ DRC : MIN ➝ DRC : MAX will be selected in turn. To Exit Setup Mode To Stop Test Tone • Wait for about 5 seconds or turn the VOLUME CONTROL of the main unit. • Press TEST TONE button again. “SETUP MODE OFF” appears on the display and exits Setup Mode. Setting DRC • STD : Set DRC effect to standard. • MAX : Set DRC effect to maximum. • MIN : Set DRC effect to minimum. 21 Caution! • This function operates only in main unit. Caution! • You cannot use test tone in 5.1CH MULTI CH function. 22 Test Tone Use test tone to check speaker connection status or defect of speaker or adjust the level. To Automatically Output Test Tone To Manually Output Test Tone √ MAIN UNIT MAIN UNIT and hold SURROUND button for about 5 seconds. 1 Press “SETUP MODE” appears on the display and enters into Setup Mode. 2 Press INPUT button 4 times. “TEST-T AUTO” appears in the display. 3 Press SURROUND button. and hold SURROUND button for about 5 seconds. 1 Press “SETUP MODE” appears on the display and enters into Setup Mode. 2 Press INPUT button 5 times. • • • “TEST-T MANU” appears in the display. • 3 Press SURROUND button. • Each time you press this button, F.L ➝ CEN ➝ F.R ➝ S.R ➝ S.B ➝ S.L ➝ S.W • Test signal will be automatically output as follows; F.L ➝ CEN ➝ F.R ➝ S.R ➝ S.B will be selected in turn. ➝ S.L ➝ S.W . • During test signal output, press SELECT ( , 4 ) button to adjust the speaker output level from -10 to +10 dB by 1 step. To Stop Test Tone Press SELECT( , )button to set the test tone as you want. • You can adjust the speaker output level from -10 to +10dB by 1 step. To Stop Test Tone Method 1) Press INPUT button 2 times. Method 1) Press INPUT button 1 time. • “TEST-T OFF” appears on the display and test tone stops. • “TEST-T OFF” appears on the display and test signal stops. Method 2) Turn VOLUME CONTROL. Method 2) Turn VOLUME CONTROL. • “SETUP MODE OFF” appears on the display and test tone stops. • “SETUP MODE OFF” appears on the display and test tone stops. Test Tone Output 23 OPERATION √ • F.L (Front-Left) : -10 ~ +10dB • CEN (Center) : -10 ~ +10dB • F.R (Front-Right) : -10 ~ +10dB • S.R (Rear-Right) : -10 ~ +10dB • S.B (Rear Center): -10 ~ +10dB • S.L (Rear-Left): -10 ~ +10dB • S.W (Subwoofer): -10 ~ +10dB Caution! • You cannot use test tone in 5.1CH MULTI CH function. 24 Setting Speaker Level You can set the balance and level of speakers √ Remote Control SPK LEVEL button to select the speaker you want. 1 Press Each time you press this button, F.L ➝ CEN ➝ F.R ➝ S.R ➝ S.B ➝ S.L ➝ S.W ➝ • Remote Control SPK LEVEL OFF will be selected in turn. …† button to set the speaker level you want. 2 Press You can adjust it from -10 to +10dB by 1 step. 1 Press and hold SURROUND for about 5 seconds. • • “SETUP MODE” appears on the display and enters into Setup Mode. The sound gets smaller at -10dB and louder at +10dB. Default setting value is 00dB. 3 Repeat the steps 1 and 2 to set it. • 3 Press SURROUND button. • Each time you press this button, F.L ➝ CEN ➝ F.R ➝ S.R ➝ S.B ➝ S.L ➝ S.W will be selected in turn. 4 Press SELECT( , ) button to set to the speaker level you want. • You can adjust it from -10 to +10dB by 1 step. • The sound gets smaller at -10dB and louder at +10dB. • Default setting value is 00dB 5 Repeat the steps 3 and 4 to set it. To Exit Setup Mode • Wait for about 5 seconds or press SPK LEVEL button of remote control to select SPK To Exit Setup Mode LEVEL OFF. • Wait for about 5 seconds or turn VOLUME CONTROL of the main unit. “SETUP MODE OFF” appears on the display and exits Setup Menu. Setting Speaker Level • F.L (Front-Left) : -10 ~ +10dB • CEN (Center) : -10 ~ +10dB • F.R (Front-Right) : -10 ~ +10dB • S.R (Rear-Right) : -10 ~ +10dB • S.B (Rear Center): -10 ~ +10dB • S.L (Rear-Left): -10 ~ +10dB • S.W (Subwoofer): -10 ~ +10dB 25 26 OPERATION INPUT button 7 times. 2 Press “LEVEL SETUP” appears on the display. Dolby Pro Logic llx Mode You can experience surround sound regardless of type of stereo mix by making existing Dolby Surround mix sound similar to discrete 5.1 Channel Surround. REMOTE CONTROL MODE button. 1 Press Each time you press this button, MUSIC ➝ CINEMA ➝ MATRIX ➝ GAME ➝ • PROLOGIC will be selected in turn. MAIN UNIT 1 Press SURROUND button briefly to select “DPL llx” Mode. • Each time you press this button, DPL ll x ➝ NEO:6 ➝ SFE ➝ STEREO will be selected in turn. , ) button. ) button, MUSIC ➝ CINEMA ➝ MATRIX ➝ GAME ➝ PROLOGIC will be selected in turn. • Each time you press SELECT ( ) button, PROLOGIC ➝ GAME ➝ MATRIX ➝ CINEMA ➝ MUSIC will be selected in turn. • Each time you press SELECT ( To Exit Setup Mode To Exit Setup Mode • Wait for about 5 seconds. • Wait for about 5 seconds. Dolby Pro Logic ll x Mode • MUSIC : Provide 5.1 Channel Surround sound to digital, analog • Sound will be output from some speaker only if you connect the external component only to Audio Input connector (or R) of the main unit. 27 or existing stereo source such as CD, TAPE, FM, TV and Stereo VC. • CINEMA : Provide 5.1 Channel Surround sound to sound track of stereo movie encoded as Dolby Surround. • MATRIX : You can feel 5.1 Channel Surround sound enjoying the space of sound. • GAME : When you play game, you can enjoy game with sound effect as if you are at actual site. • PROLOGIC : Decode(3/1 Surround) the sound track of stereo music encoded as Dolby Surround to Dolby Pro Logic. Caution! • You cannot use Dolby Pro Logic ll x Mode for multi channel signal encoded as Dolby Digital and DTS. • You cannot use Dolby Pro Logic ll x Mode in 5.1 multi- channel function. • Pro Logic works only for PCM audio signals with sampling frequency of 32KHz, 44KHz or 48KHz. • Sound will not be output from rear center speaker if PCM audio signal is not stereo but mono. 28 OPERATION 2 Press SELECT( Dolby Pro Logic llx Effect This function works only in Dolby PRO LOGIC IIX MUSIC Mode. REMOTE CONTROL MODE button to select ‘MUSIC’ Mode. 1 Press EFFECT button. 2 Press Each time you press this button, C-WIDTH ➝ DIMENSION ➝ PANORAMA will be • selected in turn. MAIN UNIT 1 Press and hold SURROUND button for about 5 seconds. • “SETUP MODE” appears on the display and enters into Setup Mode.Press • 3 3 Press …† button to select Dolby Pro Logic IIx effect you want. Press SURROUND button. • Each time you press this button, DIMENSION ➝ PANORAMA ➝ C-WIDTH will be selected in turn. • C-WIDTH: You can set from 0 to 7. • DIMENSION: You can set from 0 to 7. • PANORAMA: You can Set it ON or OFF. SELECT( 4 Press effect you want. 4 Repeat the steps 2 and 3 to set the Dolby Pro Logic IIx effect. , ) button to select Dolby Pro Logic llx 5 Repeat the steps 3 and 4 to set Dolby Pro Logic llx effect. To Exit Setup Mode • Wait for about 5 seconds or turn VOLUME CONTROL of the main unit. “SETUP To Exit Setup Mode MODE OFF” appears on the display and exits Setup Mode. • Wait for about 5 seconds . Dolby Pro Logic llx Effect • C-WIDTH : Sound will be output from center speaker only. Front-left and front-right speaker give sound field effect only. In addition, sounds are output in different volumes from Front-Left, Front-Right Speaker and Center Speaker. • DIMENSION : Adjust the sound balance if the sound is unbalanced to front or rear speaker. • PANORAMA : Give the effect expanding and covering the sound from front-left and front-right Speaker to both walls. 29 30 OPERATION button 8 times. 2 INPUT “DPL ll x MODE”appears on the display. NEO:6 Mode You can play back 2 channel sound in 6.1 channel of 360 degree surround when enjoying music or movie. REMOTE CONTROL NEO:6 MODE button. 1 Press Each time you press this button, MUSIC ➝ CINEMA will be selected in turn. • MAIN UNIT SURROUND button briefly to select “NEO:6” Mode. 1 Press Each time you press this button, DPL ll x ➝ NEO:6 ➝ SFE ➝ STEREO will be • selected in turn. SELECT( , ) button. 2 Press Each time you press this button, MUSIC ➝ CINEMA will be selected in turn. OPERATION • To Set Sound Image of Center Speaker If TV (or screen) is installed high, you can feel the balance of sound and image by raising the sound image of Center Speaker. and hold SURROUND button for about 5 seconds. 1 Press “SETUP MODE” appears on the display and enters into Setup Mode. INPUT button 9 times. 2 Press “NEO:6 MODE” appears on the display. SURROUND button. 3 Press “CEN-IMG” appears on the display. SELECT( , ) button to set the sound image you want. 4 Press You can set the sound image from 0 to 5. • • • To Exit Setup Mode • Wait for about 5 seconds. • To Exit Setup Mode • Wait for about 5 seconds or turn VOLUME CONTROL of the main unit. ‘SETUP MODE OFF’ appears on the display and exits Setup Mode. NEO : 6 Mode Caution! • NEO:6 Mode can be used in multi channel signal encoded to Dolby Digital or DTS. • Pro Logic works only for PCM audio signals with sampling frequency of 32KHz, 44KHz or 48KHz.. 31 This mode decodes 2 channel signals to high precision digital matrix decoder. DTS NEO:6 decoder discretes 2 channel sound to Discrete 6.1 channel sound. • MUSIC : NEO:6 MUSIC Mode is used as optimized to music according to played signal. Caution! • You can use this function to set the sound image of Center Speaker only in the main unit. • CINEMA : NEO:6 CINEMA Mode is used as optimized to movie according to played signal. 32 SFE Mode Refer to the unique sound existing at specific place and you can feel live sound as if you are listening at actual site. REMOTE CONTROL SEF MODE button. 1 Press Each time you press this button, LIVE ➝ ROCK ➝ CLASSIC ➝ JAZZ ➝ MIDNIGHT • ➝ HALL ➝ CINEMA ➝ CHURCH will be selected in turn. MAIN UNIT SURROUND button briefly to select ‘SFE’ Mode. Each 1 Press time you press this button, DPL II x ➝ NEO:6 ➝ SFE ➝ STEREO will be selected in turn. , ) button. ) button, LIVE ➝ ROCK ➝ CLASSIC ➝ JAZZ ➝ MIDNIGHT ➝ HALL ➝ CINEMA ➝ CHURCH will be selected in turn • Each time you press Select ( ) button, CHURCH ➝ CINEMA ➝ HALL ➝ MIDNIGHT ➝ JAZZ ➝ CLASSIC ➝ ROCK ➝ LIVE will be selected in turn. • Each time you press Select ( To Exit Setup Mode To Exit Setup Mode • Wait for about 5 seconds. • Wait for about 5 seconds. SFE Mode • LIVE, ROCK, CLASSIC, JAZZ : Select the genre suitable for the music among Live, Rock, Classic and Jazz to listen to music. • MIDNIGHT : Emphasize bass when you listen to music at midnight. • HALL : Clear music as if you are listening at concert hall. • CINEMA : Enjoy sound as if you are in cinema. • CHURCH : Enjoy magnificent sound as if you are listening at church. 33 34 OPERATION 2 Press SELECT( EX/ES Mode This mode enable you to listen 6.1 channel surround to the source encoded to Dolby Digital-EX, DTS-ES such as DVD. This function works when Dolby Digital 5.1 channel source is inputted, and does not work when LPCM and Dolby Digital 2 channel source are entered. REMOTE CONTROL Press EX/ES button. • Each time you press this button, EX/ES AUTO ➝ EX/ES ON ➝ EX/ES OFF will be selected in turn. MAIN UNIT Method and hold SURROUND button for about 5 seconds. 1 Press “SETUP MODE” appears on the display and enters into Setup Mode. • OPERATION Press INPUT button 10 times. 2 “EX/ES SETUP” appears on the display. Press SURROUND button. time you press this button, EX/ES : AUTO ➝ EX/ES : ON ➝ EX/ES : 3 Each OFF will be selected in turn. • • To Exit Setup Mode • Wait for about 5 seconds or turn VOLUME CONTROL of the main unit. ‘SETUP MODE OFF’ appears on the display and exits Setup Mode. To Exit Setup Mode • Wait for about 5 seconds or press EX/ES button of the remote control to select EX/ES : OFF. EX/ES Mode • AUTO : 7.1 channel(or 6.1 channel) sound will be played back to 7.1 channel(or 6.1 channel) and 5.1 channel sound will be automatically converted to and output as 5.1 channel. • ON : 5.1 channel sound will be converted to and output as 7.1 channel (or 6.1 channel). • OFF : 7.1 channel (or 6.1 channel) sound will be converted to and output as 5.1 channel. Dolby Digital - EX Movie sound track encoded with Dolby Digital EX can play back the rear center channel added during program mixing. Rear center channel provides fine image, in-depth and realistic feeling. Caution! • You cannot use Dolby Digital-EX in the system without rear center speaker. • You need to set it to EX/ES Mode when playing back disk encoded to Dolby Digital-EX in 6.1 channel. • Some disks encoded with Dolby Digital-EX do not contain identification signal. In this case, set EX/ES to ON. 35 DTS-ES (Discrete 6.1, Matrix 6.1) Rear center channel is added to DTS 5.1 channel, improving the sense of direction and space for sound. Since DTS-ES decoder is built-in in the main unit, you can play back the disk encoded with DTS-ES Discrete and DTS-ES Matrix. DTS-ES Discrete 6.1 can record the sound of all channels including rear center channel digitally and play back the recorded sound as they are. Caution! • You cannot use DTS-ES in the system without rear center speaker. 36 Stereo Mode You can select this mode when you listen to the sound at Front-Left speaker, Front-Right speaker and subwoofer. For Surround Mode and Input Signal Surround Mode DOLBY (MUSIC, CINEMA, MATRIX, GAME, PROLOGIC) NEO:6 (MUSIC, CINEMA) Press STEREO button. • “STEREO” appears in the display and Stereo Mode is selected. MAIN UNIT Press SURROUND button briefly to select ‘STEREO’. • Each time you press this button, DPL ll x ➝ NEO:6 ➝ SFE ➝ STEREO will be selected in turn. SFE EX/ES To Exit Setup Mode To Exit Setup Mode • Wait for about 5 seconds. • Wait for about 5 seconds. STEREO Caution! • 96KHz PCM is not played back in Stereo Mode. Display Information Decoding Dolby D Surr. EX Dolby Digital 5.1 O O O - O DIGITAL L, C, R, SL, SR, S, SW Dolby D (5.1ch) Dolby Digital 5.1 O O O - O DIGITAL L, C, R, SL, SR, SW Dolby D (2ch) Pro Logic II x O O O O O DIGITAL L, R Dolby D (2ch Surr) Pro Logic II x O O O O O DIGITAL L.PCM (Audio) Pro Logic II x O O O O O L.PCM Analog Pro Logic II x O O O O O ANALOG - DTS-ES DTS 5.1 O O O O O dts, ES L, C, R, SL, SR, S, SW DTS 96/24 DTS 96/24 O O O O O DTS 96/24 L, C, R, SL, SR, SW DTS (5.1) DTS 5.1 O O O - O dts L, C, R, SL, SR, SW L.PCM (Audio) Neo:6 O O O O - L.PCM L, R Analog Neo:6 O O O O - ANALOG - Dolby D (2ch) Neo:6 O O O O - DIGITAL L, R Dolby D (2ch Surr) Neo:6 O O O O - DIGITAL L, R, S Dolby Surr. EX SFE - - - - - DIGITAL L, C, R, SL, SR, S, SW Dolby D (5.1ch) SFE - - - - - DIGITAL L, C, R, SL, SR, SW Dolby D (2ch) SFE O O O O O DIGITAL L, R Dolby D (2ch Surr) SFE O O O O O DIGITAL DTS-ES SFE - - - - - dts, ES DTS (5.1ch) SFE - - - - - dts L, C, R, SL, SR, SW L.PCM (Audio) SFE O O O O O L.PCM L, R Analog SFE O O O O O ANALOG - Dolby D Surr. EX Dolby Digital EX O O O O O DIGITAL L, C, R, SL, SR, S, SW Dolby D (5.1ch) Dolby Digital EX O O O O O DIGITAL L, C, R, SL, SR, SW DTS-ES DTS-ES O O O O O dts, ES L, C, R, SL, SR, S, SW DTS (5.1ch) DTS-ES O O O O O dts L, C, R, SL, SR, SW Dolby Surr. EX Stereo O - - - O DIGITAL L, C, R, SL, SR, S, SW Dolby D (5.1ch) Stereo O - - - O DIGITAL L, C, R, SL, SR, SW Dolby D (2ch) Stereo O - - - - DIGITAL L, R, Dolby D (2ch Surr) Stereo O - - - - DIGITAL DTS-ES Stereo O - - - O dts, ES L, C, R, SL, SR, S, SW DTS 96/24 Stereo O - - - O dts 96/24 L, C, R, SL, SR, SW DTS (5.1ch) Stereo O - - - O dts L, C, R, SL, SR, SW L.PCM (Audio) Stereo O - - - - L.PCM L, R L.PCM 96KHz Stereo O - - - - L.PCM L, R Analog Stereo O - - - - ANALOG - L/R Display Signal Format Channel Status L, R, S L, R OPERATION REMOTE CONTROL Output Channel SL C SB SubW SR Input Signal L, R, S L, C, R, SL, SR, S, SW L, R, S • When PCM and Analog Stereo signal are input, left/right channel is played back in Stereo Mode. L/R : Front Speaker (Left/Right) C : Center Speaker SL/SR : Rear Speaker (Left/Right) S : Rear Center Speaker SW : Subwoofer Caution! • 2 channel Dolby Digital signal has Dolby Digital Pro Logic. Speaker Setup is set to LARGE, SMALL, or YES. • If there is no surround signal in DVD disk, sound will not output from rear-left speaker, rear-right speaker, center speaker, and subwoofer. 37 38 Listening to Radio Presetting Radio Stations You can listen to the chosen band (FM, AM broadcast stations) by using either the automatic or manual tuning operation. You can preset to 30 stations including FM and AM broadcasting. REMOTE CONTROL Ex) If you preset FM 89.1 station in 2ch TUNER button. 1 Press Each time you press this button, FM ➝ AM will be selected in turn. • Select button and then TUNING/CH( 2 Press select 89.1. , ) button to • Refer to step 2, page 39, to tune in automatically and manually. TUNER MEMORY button. 3 Press Tuner number will blink on the display. • REMOTE CONTROL MAIN UNIT 1 Press TUNER button. 1 Press INPUT button to select FM or • Each time you press this button, FM ➝ AM will be repetitively selected. 1) Press ENTER button to select PRESET. 2) Press TUNING/CH( , ) button to select the preset frequency. • Automatic Tuning 2 : 1) Press ENTER button to select MANUAL 2) Press and hold TUNING/CH( , ) button to automatically tune in frequency. • Manual Tuning : 1) Press ENTER button to select MANUAL. 2) Press TUNING/CH( , ) button briefly to increase or decrease frequency by step by step. TUNING/CH( , 4 Press You can select from 1 to 30ch. ) button to select 2ch. • 2 Select the frequency. • Automatic Tuning : Press and hold TUNING/CH( , automatically tune in frequency. ) button to RADIO OPERATION 2 Select frequency. • Automatic Tuning 1 : AM. TUNER MEMORY button. 5 Press Tuner number will disappear and 89.1 station will be preset in 2ch. • • Manual Tuning : Press TUNING/CH( , ) button briefly to increase or decrease frequency by step by step. 6 To preset other stations, repeat the steps 2 to 5. To Listen to Preset Station • Press Select button of the remote control to select the PRESET and press TUNING/CH ( , ) button. To Listen to Mono/Stereo Press MO/ST button. • Each time you press this button, STEREO, MONO will be selected in turn. • If you select MONO in the area with weak reception and blanket area, you can listen to clear broadcasting without noise. • This function works only in Remote Control. 39 40 About RDS broadcasting PTY (Program Type) indication and PTY-SEARCH function Using the RDS (Radio Data System) to receive FM stations RDS allows FM stations to send an additional signal along with their regular program signals. For example,the stations send their station names,as well as information about what type of program they broadcast, such as sports or music,etc. When tuned to an FM station which provides the RDS service,the RDS indicator lights up on the display. • Description on RDS function 1. PTY (Program Type) : Displays the type of programme currently being broadcast 2. PS NAME (Program Service Name) : Indicates the name of broadcasting station and is composed of 8 characters. 3. RT (Radio Text) : Decodes the text broadcast by a station (if any) and is composed of maximum 64 characters. 4. CT (Clock Time) : Decodes the real time clock from the FM frequency. • Some stations may not transmit PTY, RT or CT information therefore this may not be displayed in all cases. 5. TA (Traffic Announcement) : When this symbol flashes it shows that the traffic announcement is in progress. One of the advantages of the RDS service is that you can locate a particular kind of program from the preset channels by specifying the PTY codes. To search for a program using the PTY codes Before you start, remember... • The PTY Search is only applicable to preset • • • stations. To stop searching any time during the process, press PTY SEARCH while searching. There is a time limit in doing the following steps. If the setting is cancelled before you finish, start from step 1 again. When pressing the buttons on the primary remote control, make sure that you have selected the FM station using the primary remote control. • RDS is not available for AM broadcasts. • RDS may not operate correctly if the station tuned is not transmitting RDS signal properly or if the signal strength is weak. 1 Press PTY SEARCH while listenning to an FM station. What information can RDS signals provide? You can see the RDS signals the station sends on the display. 2 TO show the RDS signals PS (Program Service) :While searching,"PS"appears and then the station names will be displayed."NO PS" appears if no signal is sent. RT(RadioText) : while searching,"RT"appears and then text messages the station sends will be displayed. "NO RT"appears if no signal is sent. Frequency : station frequency (non-RDS service) About characters shown in the display When the display shows PS,or RT signals,the following characters are used. • The display window cannot differentiate upper case and lower case lrtters and always uses upper case letters. • The display window cannot show accented letters, “A,” for instance, may stans for accented “A’s” like “À, Â, Ä, Á, Åand Ã.” 3 Press PTY SEARCH again, while the PTY code selected in the previous step is still on the display. • The center unit searches 15 preset FM stations,stops when it finds the one you have selected, and tunes in that station. NEWS AFFAIRS INFO SPORT EDUCATE DRAMA • News including an announced opinion and report • Several matters including a current incident, documentary, discussion and analysis. • Information including weights and measures, returns and forecast, matters interesting the customer, medical information, etc. • Sports • Education • Drama-Radio serial, etc. CULTURE • Culture-National or local culture including the religious problem, social science, language, theater,etc. SCIENCE • Natural science and technology VARIED • Others-Speech, amusing program (quiz, game), interview, comedy and satirical play, etc. POP M • Pop music ROCK M • Rock music M.O.R.M • Current contemporary music considered to be “easylistening.” LIGHT M • Light classical music- Classical music and instrumental and chorus music CLASSIC • Heavy classical music-Orchestra music, symphony, chamber music and opera OTHER M • Other music - Jazz, R&B country music WEATHER • Weather FINANCE • Finance CHILDREN • Children’s programmes SOCIAL A • Social affairs RELIGION • Religion PHONE IN • Phone in TRAVEL • Travel LEISURE • Leisure JAZZ • Jazz COUNTRY • Oldies Music NATION M • Folk Music OLDIES • Country Music FOLK M • National DOCUMENT RADIO OPERATION Press RDS DISPLAY while listening to an FM station. Each time you press the button, the display change to show you the following information: Press the PTY-or PTY+until the PTY code you want appears on the display. • The display gives you the PTY codes described to the right. Program Type Display • Documentary • If searching finishes at once,“PS”,and “RT” will not appear on the display. 41 42 Convenient Functions Reset Function Sleep Timer Function You can set the time that this unit will shut itself off. REMOTE CONTROL Press the SLEEP button. • SLEEP : OFF ➝ 15 ➝ 30 ➝ 45 ➝ 60 ➝ 90 ➝ 120MIN will be selected in turn. REMOTE CONTROL 1 Press the MUTE button. • MUTE appears on the display. 2 Press “0” button five times and then press ENTER button. …,† buttons to select “YES”. 3 Press The unit automatically back on in 5 seconds. Caution! To Check Sleep Timer Press SLEEP button. • The remaining time before this unit will shut itself off is displayed on the display. • Pressing the button again changes the sleep time from what you have set earlier. To Cancel Sleep Timer • Press SLEEP button until SLEEP : OFF appears on the display. Mute Function This function is useful what answering a doorbell or telephone call. REMOTE CONTROL Press the MUTE button. • MUTE appears on the display. Using the RESET function will erase all stored settings. Do not use this unless necessary. Turning Display On/Off You can turn the display off to prevent the dazzling light or when you go to bed. REMOTE CONTROL Press the DISPLAY OFF button. • Each time you press this button, the display is turned on or off. Using Headphone Use headphones (not supplied) for private listening pleasure. Connect the headphone to the headphone jack and listen to music. MISCELLANENOUS To Output Sound Again Press MUTE button again. • MUTE will disappear and sound will Output. Do not volume up when you use headphone. It may damage your hearing. Caution! • Sleep , Mute, Display Off function will work only in Remote Control. 43 44 Operating TV with Remote Control TV Brand Code List 1 2 3 4 Brand Press MODE button to make the TV indicator on the remote control flash. Press POWER( TV. ) button to turn on the Point the remote control toward the TV. While holding down POWER( ) button, enter the code corresponding to your brand of TV. • If the code matches the TV's code, the TV will be turned off. • If there is more than one code listed for your TV in the table, enter one at a time to determine which code works. Ex) For a ‘Samsung’ TV While holding down POWER button, use the Numeric buttons to enter 00, 01, 02, 03, 04, and 05. • You can use the TV POWER, VOLUME, CHANNEL, and Numeric buttons (0~9). AOC BELL & HOWELL(M.WARDS) BROCSONIC CANDLE CETRONIC CITIZEN CINEMA CLASSIC CONCERTO CONTEC CORONADO CRAIG CROSLEX CROWN CURTISMATES CXC DAEWOO DAYTRON DYNASTY EMERSON FISHER FUNAI FUTURETECH GENERAL ELECTRIC(GE) HALL MARK HITACHI INKEL JC PENNY JVC KTV KEC KMC LG(GOLDSTAR) Code Number 056, 057, 058 001, 015 001, 002, 003, 004,005, 006, 007, 008, 009, 010, 011, 012, 013, 014 001, 018, 040, 048 057, 058, 081 059, 060 018 003 003, 018, 025 097 003 018 046 015 003, 005, 061, 082, 083, 084 062 003 059, 061, 063 003 002, 003, 004, 015,016, 017, 018, 019, 020, 021, 022, 023, 024, 025, 026, 027, 028, 029, 030, 032, 034, 035, 036, 040, 048, 059, 090, 099, 100 040 003 003, 015, 040, 046, 059, 061, 064, 082, 083, 084, 085 019, 065, 103 003 003 006, 040, 056, 059, 066, 067, 068 040 015, 018, 050, 059, 069 045 056, 059, 067, 086 070 059, 061, 087, 088 003, 015, 040 015 001, 015, 016, 017, 037, 038, 039, 040, 041, 042, 043, 044, 054, 086 Brand LUXMAN LXI(SEARS) MAGNAVOX MARANTZ MATSUI MGA MITSUBISHI/MGA MTC NEC NIKEI ONKING ONWA PANASONIC PENNEY PHILCO PHILIPS PIONEER PORTLAND PROTON QUASAR RADIO SHACK RCA/PROSCAN REALISTIC SAMPO SAMSUNG SANYO SCOTT SEARS SHARP SIGNATURE 2000(M.WARDS) SONY SOUNDESIGN SPECTRICON SSS Code Number 018 019, 054, 056, 059, 060, 062, 063, 065, 071 015, 017, 018, 048, 054, 059, 060, 062, 072, 089 040, 054 054 018, 040 018, 040, 054, 059, 060, 075, 101 018 018, 019, 020, 040, 059, 060 003 003 003 006, 007, 008, 009, 054, 066, 067, 073, 074 018 003, 015, 017, 018, 048, 054, 059, 062, 069, 090 015, 017, 018, 040, 048 054, 062, 072, 112, 114, 117, 118 063, 066, 080, 091 015, 018, 059 040 006, 066, 067 017, 048, 056, 060, 061, 075 018, 059, 067, 076, 077 078, 092, 093, 094 003, 019 040 000, 015, 016, 017, 040, 043, 046, 047, 048, 049, 054, 059, 060, 098 019, 061, 065, 101, 102, 103, 104 003, 040, 060, 061 015, 018, 019 015, 057, 064, 101, 105, 106, 115 057, 058 050, 051, 052, 053, 055, 101 003, 040 001 018 Brand SYLVANIA SYMPHONIC TATUNG TECHWOOD TEKNIKA TMK TOSHIBA VIDTECH VIDECH WARDS YAMAHA YORK YUPITERU ZENITH ZONDA DONGYANG LOWE FINLUX YOKO LOEWE OPTA PHONOLA RADIOLA SCHNEIDER AKAI GRUNDIG BLAUPUNKT SIEMENS CGE IMPERIAL MIVAR SABA BANG&OLUFSEN BRIONVEGA FORMENTI METZ WEGA RADIOMARELLI SINGER SINUDYNE TELEFUNKEN Code Number 018, 040, 048, 054, 059, 060, 062 061, 095, 096 006 018 003, 015, 018, 025 018, 040 019, 057, 063, 071, 101 107, 109, 110, 111, 113 018 059, 060, 069 015, 017, 018, 040, 048, 054, 060, 064 018 040 003 058, 079 001 003, 054 054 054, 109, 114 054 054, 114 054, 112, 114 054, 112 054 103 108, 109, 113, 119, 120, 121 108 108 113 113 113 114 114 114 114 114 114 114 114 114 116 MISCELLANENOUS 5 If TV is turned on or off when you press the power button of the remote control, the setting is completed. ADMIRAL(M.WARDS) A MARK ANAM • The remote control may not work on some brands of TVs. Also, some operation may not be possible depending on your brand of TV. • If you do not set the remote control with the code for your brand of TV, the remote control will work on a Samsung TV by default. 45 46 Operating VCR (DVD) with Remote Control VCR Brand Code List Brand 1 Press MODE button to make VCR indicator on the remote control flash. • If you operate DVD, press Device Select button to make DVD indicator on the remote control flash. 2 3 4 Press POWER( VCR (DVD). ) button to turn on the Point the remote control toward the VCR (DVD). While holding down POWER( ) button, enter the code corresponding to your brand of VCR (DVD). • If the code matches the VCR (DVD)'s code, the VCR (DVD) will be turned off. • If there is more than one code listed for your VCR (DVD) in the table, enter one at a time to determine which code works. 5 If VCR (DVD) is turned on or off when you press the power button of the remote controller, the setting is completed. AOC AUDIO DYNAMIC BELL & HOWELL(M.WARDS) BROKSONIC CANON CAPEHART CITIZEN CRAIG CRITERION CURTIS MATHES DAEWOO DAYTRON DBX EMERSON FISHER FUNAI GENERAL ELECTRIC(GE) GO VIDEO HARMAN KARDON HITACHI HQ INSTANT REPLAY JCL JCP JC PENNY JVC KENWOOD LG(GOLDSTAR) • You can use VCR (DVD) POWER, VOLUNE, PLAY, PAUSE, STOP, SKIP and Numeric button (0~9). LXI(SEARS) MAGIN MAGNAVOX • The remote control may not work on some brands of VCR (DVD)s. Also, some operations may not be possible depending on your brand of VCR (DVD). • If you do not set the remote control with the code for your brand VCR (DVD), the remote control work on a Samsung VCR (DVD) by default. 47 MARANTZ MARTA Code Number 043, 106 044, 045, 046 088, 089, 090 001, 002, 003, 004, 005, 033 091 019, 047, 092 048, 093 092, 094, 095 001, 033, 049, 091 011 050 050, 072, 096 051 001, 031, 032, 033, 044, 091 006, 007, 008, 009, 010, 011, 012, 013, 014, 015, 016, 017, 018, 046, 051, 091 011 019, 047, 052, 092 025, 031, 032, 044, 046, 094, 095, 097, 098, 099 009, 048, 053, 054, 055, 100 044 001, 031, 032, 033, 056, 091 059, 060, 061 019 020, 021, 049, 054, 062, 100 051 001, 033, 049, 091 001, 033 025 047, 048, 052, 062, 091, 092 001, 033, 047, 052, 063, 064, 065, 092 047, 050, 052, 092 019, 020, 021, 022, 023, 024, 025, 026, 027, 028, 029, 030, 050 020, 025, 044, 048, 050, 053, 054, 055, 062, 100 072 001, 031, 032, 033, 049, 066, 067, 091 001, 019, 033, 047, 052, 092, 110 025, 050 Brand MEI MEMOREX MINOLTA MITSUBISHI/MGA MTC MULTITECH NEC OLYMPIC OPTIMUS ORION PANASONIC PENNEY PENTAX PHILCO PHILIPS PILOT PIONEER PORTLAND QUASAR RICO RCA/PROSCAN REALISTIC 044, 048, 054, 091, SAMSUNG SANYO SANSUI SCOTT SEARS SHARP SINGER SIGNATURE 2000(M.WARDS) SHINTOM SONY STS SYLVANIA SYMPHONIC TANDY Code Number 001, 033 001, 025, 033, 054, 091, 100 020, 021, 062 068, 069, 070, 101, 102 072 044, 057, 069 019, 047, 052, 057, 092 049, 091 101 103 001, 004, 033, 049, 067, 091, 107 019, 020, 072 001, 020, 021, 033, 062 001, 033, 046, 049, 091, 094 001, 030, 033, 049, 050, 066, 091 025 049 011 001, 033, 049, 067, 091, 107, 108 036 001, 020, 021, 031, 032, 033, 049, 051, 062, 066, 070, 091, 104 001, 009, 025, 033, 101, 105 000, 006, 031, 032, 057, 058, 071, 072, 073, 074, 075, 076, 077, 078, 079, 080, 081 008, 009, 046, 048, 050, 054, 058, 093, 100 092 006, 051, 054, 057, 069, 070, 100, 101 020, 021, 025 043, 105, 106 096 043, 044, 054, 100, 106 096 034, 035, 036, 037, 038, 039, 040, 041, 042,082, 083, 084, 085, 086 020 001, 033, 044, 049, 066, 091 044 009 Brand TASHIRO TATUNG TEAC TECHNICS TEKNIKA TOSHIBA TOTEVISION TAEKWANG UNITECH VECTOR RESEARCH VIDEO CONCEPTS VIDEOSONIC WARDS YAMAHA ZENITH Code Number 050 047, 052, 092 044, 047, 052, 092 001, 033, 049, 091 001, 025, 033 006, 051 025, 072 087 072 019 019 072 001, 020, 031, 032, 033, 043, 050, 054, 072, 100, 105, 106, 109 019, 047,048, 052, 092, 019, 047,048, 052, 092 DVD Brand Code List Brand DENON DOONOON DMTECH FISHER GE HARMAN/KARDON JVC KENWOOD LG MAGNAVOX MITSUBISHI ONKYO OPTIMUS PANASONIC PROSCAN PHILIPS PIONEER RCA SAMSUNG SANYO SONY THETA DIGITAL TOSHIBA YAMAHA ZENITH TAEGWANG PS2 X-BOX APEX MARANTZ Code Number 003, 032 019 017 002 006 012 010, 013 008 001 004 005, 016 004, 014 011 021 006 004, 023 007, 011, 022, 025 006 000, 027 002 015, 020 011 004, 018 009, 033 004, 024 026 028 029 030 031 MISCELLANENOUS Ex)For a ‘Samsung’ VCR (DVD) While holding down POWER( ) button, use the Numeric button to enter 00, 32~45, 87, and 88. ADMIRAL(M.WARDS) AWIA AKAI ANAM 48 Before Calling for Service Check Symptom Can't turn it on. It does not work when the button is pressed. • Is the power code plugged into the outlet? • Isn’t the air too dry to cause electrostatics? Symptom Remedy • Is the rear center speaker connected • Connect the power plug to the outlet. • Disconnect the power plug and connect it again. Check There is no sound from rear center speaker properly? component connected properly? • Does the Mute function work? Sound is not produced. • Is the volume set to minimum? • Is the speaker setup selected to NONE? to NONE in Speaker Setup? • Isn’t the external component connected Remote controller does not work. • Are the batteries exhausted? • Is the distance between remote The sound from each device is changed during stereo playback. • Is the left/right speaker or left/right properly? control and main unit proper? input/output code connected properly? • Is AM or FM antenna connected Can't receive broadcasting. properly? • Press Mute button to cancel the function. • Adjust the volume. Can't select EX/ES Mode. • Refer to page 17~18 to select LARGE, SMALL or YES. Can't select Dolby Pro Logic • Refer to page 17~18 to select LARGE or NONE in Speaker Setup? • Is the input signal selected properly? • Use 5.1 channel external component. • Is the input signal selected properly? • Select 2 channel Dolby Digital, PCM, and speaker. properly? • Is S.SPK (Rear) set to NONE in Speaker Setup? • Is Surround Mode selected to Stereo? There is no sound from center speaker • Operate at close distance. • Check the left/right channel and properly Can't select NEO:6 Mode. • Is the input signal selected properly? • Use PCM and Analog input signal. There is no sound when playing DTS encoded DVD and CD. • Is analog input selected? • Check whether digital external component is properly connected and refer to page 19 to select the digital input. connect it. • Properly connect the antenna. • If the input strength of antenna connector is • Refer to page 17~18 to connect it properly. • Refer to page 17~18 to select LARGE or SMALL. • Refer to page 27~38 to select other Surround Mode. • Refer to page 9~10 to connect it properly. • Is C.SPK (Center) selected to NONE in • Refer to page 17~18 to select LARGE or • Is the Surround Mode selected to Stereo? Analog input signal. • Replace with new batteries. • Is the center speaker connected properly? Speaker Setup? SMALL. SMALL. √√ Product Protection Function œœ DC Protection Circuit MISCELLANENOUS There is no sound from rear Mode to EX/ES. • Is SB SPK (Rear Center) selected to • Properly connect it. weak, install the FM antenna at the place with good reception. • Is the rear speaker connected SMALL. • Refer to page 35~36 to select Surround • Properly connect it. llx Mode. Picture does not appear when the function is selected. • Refer to page 9~10 to connect it properly. • Refer to page 17~18 to select LARGE or • Is the SB SPK (Rear Center) selected • Is Surround Mode selected to EX/ES • Are the speaker and external Remedy • If DC is output from output connector, DC protection circuit works automatically to protect the speaker. Heat Protection • Protection function works if the main unit is overheated or power transformer is overheated. appears in the display when the “ ” function works. - If speaker terminal is shorted - If speaker cord is shorted If there is no problem when you turn it on again after turning it off, PROTECTION mark will disappear on the display and the unit will work properly. • If PROTECTION appears on the display, check whether speaker terminal is shorted and then turn on the device. • Refer to page 27~38 to select other Surround Mode. 49 50 Memo Specifications GENERAL FM TUNER AM TUNER AMPLIFIER FREQUENCY RESPONSE VIDEO OUTPUT Power Supply Standby Power Consumption Power Consumption Weight Dimensions (W x H x D) Operating Temperature Range Operating Humidity Range Frequency Response Usable Sensitivity S/N Ratio Distortion Stereo Separation Tuner Output Level Frequency Response S/N Ratio Usable Sensitivity Distortion Rated Output Front Speaker(Left+Right) Center Speaker Rear Speaker(Left+Right) Rear Center Speaker Input Sensitivity/Impedance S/N Ratio(Analog Input/5.1CH Analog Input) Separation(1KHz) Analog Input/5.1CH Analog Input Digital Input/96KHz PCM TV Format Input Level/Impedance Output Level/Impedance Video Frequency Response Component Video Frequency Response S/N Ratio 230V, 50 Hz 0.9W 110W 4.65 kg 430 x 65 x 350 mm +5° C~+35° C 10%~75% 87.5~108.0MHz 12dBf MONO/STEREO 55/55dB MONO/STEREO 0.3/0.8% 30dB 1KHz, 75KHz Dev 522~1611KHz 40dB 60dB uV/m(Loop Antenna) 2% (MOD:80%) 20Hz~20KHz/THD = 1% 6 Ω 90W/CH 6 Ω 90W/CH 6 Ω 90W/CH 6 Ω 90W/CH 450mV/47kΩ 80dB 60dB 20Hz~20KHz(+_ 3dB) 20Hz ~44KHz(+_ 3dB) NTSC/PAL 1Vp-p/75 Ω 1Vp-p/75 Ω 5Hz to 10KHz(-3dB) 5Hz to 40KHz(-3dB) 60dB ❈ S/N ratio, distortion, separation and usable sensitivity are based on measurement using AES-17 filter. 51 52
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project