Acer LCD Monitor Quick Start Guide (QSG) Important safety instructions 1. 2. 3. 4. 5. 6. 7. To clean the LCD monitor screen: • Turn off the LCD monitor and unplug the power cord. • Spray a non-solvent cleaning solution onto a rag and clean the screen gently. Do not place the LCD monitor near a window. Exposing the monitor to rain, moisture or sunlight can severely damage it. Do not apply pressure to the LCD screen. Excessive pressure may cause permanent damage to the display. Do not remove the cover or attempt to service this unit yourself. An authorized technician should perform servicing of any nature. Store the LCD monitor in a room with a temperature of -20° to 60° C (-4° to140° F). Storing the LCD monitor outside this range may result in permanent damage. Immediately unplug your monitor and call an authorized technician if any of the following circumstances occur: • Monitor-to-PC signal cable is frayed or damaged. • Liquid spills onto the LCD monitor or the monitor is exposed to rain. • The LCD monitor or case is damaged. In order to prevent damage to the LCD panel, do not place the monitor face down on a surface. Connecting your monitor to a computer 1. 2. 3. 4. 5. Turn off your computer and unplug your computer's power cord. Connect the signal cable to the VGA (optional) and /or DVI (optional) and /or HDMI (optional) input socket of the monitor, and the VGA (optional) and /or DVI (optional) and /or HDMI (optional) output socket of the graphics card on the computer. Then tighten the thumbscrews on the signal cable connector. Optional: Connect the audio input socket (AUDIO IN) of the LCD monitor and the line-out port on the computer with the audio cable. Insert the monitor power cable into the power port at the back of the monitor. Plug the power cords of your computer and your monitor into a nearby electrical outlet. VGA FreeSync (HDMI only): It can allow a FreeSync supported graphics source to dynamically adjust display refresh rate based on typical content frame rates for power efficient, virtually stutter free and low-latency display update. English Please read the following instructions carefully. English External controls Function key a. b. c. d. e. Monitor power off status Press to switch power on. In the normal display, anytime to Press more than 5 seconds switch to turn off the power. Blue indicates power on. Amber indicates standby/power saving mode. No light display indicates Power off. Press to any directions switch key to display First Menu. Press again to enter next function in the First Menu. First menu of "Function 1 & Function 2" allows users to customize, "Main Menu" and "Input" are fixed functions can’t be changed. The single toggle button on the backside of the Display bezel operates like a joystick. To move the cursor, simply toggle the button in four directions. Press the button to select desires option. In Main Menu The Green indicates operable, Grey indicates inoperable. Regulations and safety notices FCC notices CE declaration of conformity Hereby, Acer Inc., declares that this LCD monitor is in compliance with the essential requirements and other relevant provisions of EMC Directive 2014/30/EU, Low Voltage Directive 2014/35/EU, and RoHS Directive 2011/65/EU and Directive 2009/125/EC with regard to establishing a framework for the setting of ecodesign requirements for energy-related product. Notice: Shielded cables All connections to other computing devices must be made using shielded cables to maintain compliance with EMC regulations. Notice: Peripheral devices Only peripherals (input/output devices, terminals, printers, etc.) certified to comply with the Class B limits may be attached to this equipment. Operation with non-certified peripherals is likely to result in interference to radio and TV reception. Caution Changes or modifications not expressly approved by the manufacturer could void the user authority, which is granted by the Federal Communications Commission, to operate this product. In order to prevent damage to the monitor, do not lift the monitor by its base. Operation conditions This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Notice: Canadian users CAN ICES-3(B)/NMB-3(B) Disposal of waste equipment by user in private household in the European Union This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information ab ut where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or the shop where you purchased the product. English This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the device and receiver. • Connect the device into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/television technician for help. English SPECIFICATION LCD Panel Driving system Size Pixel pitch Brightness Contrast Viewable angle (Typical) Response time Panel Type Video H-Frequency V-Frequency Display Colors Dot Clock Max. Resolution Plug & Play Energy Efficiency Class *Annual Energy Consumption(Typical) ON Mode Power consumption Sleep Mode @200cd/m2 Off Input Connector Speakers Audio Maximum Screen Size Power Source Environmental Considerations Dimensions Weight (N. W.) Mechanism spec External Controls: Functions TFT Color LCD 31.5 "W (80cm) 0.36375 mm(H) x 0.36375mm(V) 250cd/m2(Typical) 100,000,000:1Max. (ACM) 178° (H) 178° (V) (CR ≥ 10) 4ms (GTG,Typical) VA Digital Interface 30~83KHz(VGA/DVI), 30~85KHz(HDMI) 55~76Hz(VGA/DVI), 48~75Hz(HDMI) 16.7M Colors 170MHz 1920X1080@60Hz(VGA/DVI), 1920X1080@75Hz(HDMI) VESA DDCCI/DDC2B A 50 (kWh) (for HDMI-input Model) 30W(typ.) 0.45W(typ.) 0.35W(typ.) D-Sub(only D-Sub Model) DVI (Only DVI Model) HDMI (Only HDMI Model) 2W x 2 Audio-Output (Only Audio-Output Model) Horizontal:698.4mm Vertical:392.85mm 100-240V~, 50/60Hz Operating Temp: 5° to 35°C Storage Temp: -20° to 60°C Operating Humidity: 10% to 85% 721.2 (W) x 529.1(H) x 246.7(D)mm 8.17kg Unit (net) Tilt: -5° to +13° Swivel: No Height adjustment: No Pivot: No Detachable foot stand: No Brightness Over Drive Contrast FreeSync Black Boost Aim point Blue Light Language ACM OSD Timeout Super Sharpness Transparency Auto Config Refresh Rate Num H. Position Input V. Position Auto Source Focus Wide Mode Clock Hot Key Assignment Gamma DDC/CI Color Temp HDMI Black Level Modes Quick Start Mode sRGB mode Reset 6-axis Hue 6-axis Saturate Volume * All specifications are subject to change without notice. Find manuals and other documents for your Acer product on the official Acer support website. *Annual energy consumption is calculated using the typical power consumption 4 hours per day, 365 days per year.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project