Acer | Z35 | Acer Z35 User Manual (Z35P)

Acer LCD Monitor
User Guide
Copyright © 2016. Acer Incorporated.
All Rights Reserved.
Acer LCD Monitor User Guide
Original Issue: 12/2016
Changes may be made periodically to the information in this publication without obligation
to notify any person of such revisions or changes. Such changes will be incorporated in new
editions of this manual or supplementary documents and publications. This company makes
no representations or warranties, either expressed or implied, with respect to the contents
hereof and specifically disclaims the implied warranties of merchantability or fitness for a
particular purpose.
Record the model number, serial number, purchase date and place of purchase information in
the space provided below. The serial number and model number are recorded on the label
affixed to your computer. All correspondence concerning your unit should include the serial
number, model number and purchase information.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronically, mechanically, by photocopy, recording or otherwise,
without the prior written permission of Acer Incorporated.
Acer LCD Monitor User Guide
Model number: __________________________________
Serial number: ___________________________________
Date of purchase: ________________________________
Place of purchase: ________________________________
Acer and the Acer logo are registered trademarks of Acer Incorporated. Other companies'
product names or trademarks are used herein for identification purposes only and belong to
their respective companies.
iii
Information for your safety and
comfort
Safety instructions
Read these instructions carefully. Keep this document for future reference.
Follow all warnings and instructions marked on the product.
Special notes on LCD monitors
The following are normal with the LCD monitor and do not indicate a problem.
•
Due to the nature of the fluorescent light, the screen may flicker during
initial use. Turn off the power switch and then turn it on again to make
sure the flicker disappears.
•
You may find slightly uneven brightness on the screen depending on the
desktop pattern you use.
•
The LCD screen has 99.99% or more effective pixels. It may include
blemishes of 0.01% or less such as a missing pixel or a pixel lit all the time.
•
Due to the nature of the LCD screen, an afterimage of the previous screen
may remain after switching the image, when the same image is displayed
for hours. In this case, the screen is recovered slowly by changing the image
or turning off the power switch for a few hours.
Cleaning your monitor
Please carefully follow these guidelines when cleaning the monitor:
•
Always unplug the monitor before cleaning.
•
Use a soft cloth to wipe the screen and cabinet front and sides.
iv
Accessibility
Be sure that the power outlet you plug the power cord into is easily accessible
and located as close to the equipment operator as possible. When you need to
disconnect power from the equipment, be sure to unplug the power cord from
the electrical outlet.
Safe listening
To protect your hearing, follow these instructions.
•
Gradually increase the volume until you can hear it clearly and comfortably
and without distortion.
•
After setting the volume level, do not increase it after your ears have
adjusted.
•
Limit the amount of time listening to music at high volume.
•
Avoid turning up the volume to block out noisy surroundings.
•
Turn the volume down if you can't hear people speaking near you.
Warnings
•
•
•
•
•
•
•
•
Do not use this product near water.
Do not place this product on an unstable cart, stand or table. If the product
falls, it could be seriously damaged.
Slots and openings are provided for ventilation to ensure reliable
operation of the product and to protect it from overheating. These
openings must not be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug or other similar surface.
This product should never be placed near or over a radiator or heat
register, or in a built-in installation unless proper ventilation is provided.
Never push objects of any kind into this product through cabinet slots as
they may touch dangerous voltage points or short-out parts that could
result in a fire or electric shock. Never spill liquid of any kind onto or into
the product.
To avoid damage of internal components and to prevent battery leakage,
do not place the product on a vibrating surface.
Never use it under sporting, exercising, or any vibrating environment
which will probably cause unexpected short current or damage internal
devices.
The adapter is only used for this monitor ,do not be used for other purposes.
Your device uses one of the following power supplies:
Manufacturer: Delta Electronics, Inc., Model: ADP-120RH D
Manufacturer: Chicony Power Technology Co., Ltd. Model: A15-120P1A
Using electrical power
•
•
•
This product should be operated from the type of power indicated on the
marking label. If you are not sure of the type of power available, consult
your dealer or local power company.
Do not allow anything to rest on the power cord. Do not locate this
product where people will walk on the cord.
If an extension cord is used with this product, make sure that the total
v
•
•
ampere rating of the equipment plugged into the extension cord does not
exceed the extension cord ampere rating. Also, make sure that the total
rating of all products plugged into the wall outlet does not exceed the fuse
rating.
Do not overload a power outlet, strip or receptacle by plugging in too
many devices. The overall system load must not exceed 80% of the branch
circuit rating. If power strips are used, the load should not exceed 80% of
the power strip's input rating.
This product's power cord is equipped with a three-wire grounded plug.
The plug only fits in a grounded power outlet. Make sure the power outlet
is properly grounded before inserting the power cord plug. Do not insert
the plug into a non-grounded power outlet. Contact your electrician for
details.
Warning! The grounding pin is a safety feature. Using a power
outlet that is not properly grounded may result in electric shock
and/or injury.
Note: The grounding pin also provides good protection from
unexpected noise produced by other nearby electrical devices that
may interfere with the performance of this product.
•
Use the product only with the supplied power supply cord set. If you need
to replace the power cord set, make sure that the new power cord meets
the following requirements: detachable type, UL listed/CSA certified, type
SPT-2, rated 7 A 125 V minimum, VDE approved or its equivalent, 4.6
meters (15 feet) maximum length.
Product servicing
Do not attempt to service this product yourself, as opening or removing covers
may expose you to dangerous voltage points or other risks. Refer all servicing to
qualified service personnel.
Unplug this product from the wall outlet and refer servicing to qualified service
personnel when:
•
the power cord or plug is damaged, cut or frayed
•
•
•
•
•
liquid was spilled into the product
the product was exposed to rain or water
the product has been dropped or the case has been damaged
the product exhibits a distinct change in performance, indicating a need
for service
the product does not operate normally after following the operating
instructions
vi
Note: Adjust only those controls that are covered by the operating
instructions, since improper adjustment of other controls may
result in damage and will often require extensive work by a
qualified technician to restore the product to normal condition.
Potentially explosive environments
Switch off your device in any area with a potentially explosive atmosphere and
obey all signs and instructions. Potentially explosive atmospheres include areas
where you would normally be advised to turn off your vehicle engine. Sparks in
such areas could cause an explosion or fire resulting in bodily injury or even
death. Switch off the device near gas pumps at service stations. Observe
restrictions on the use of radio equipment in fuel depots, storage and
distribution areas; chemical plants; or where blasting operations are in progress.
Areas with a potentially explosive atmosphere are often, but not always,
marked. They include below deck on boats, chemical transfer or storage
facilities, vehicles using liquefied petroleum gas (such as propane or butane),
and areas where the air contains chemicals or particles such as grain, dust or
metal powders.
Additional safety information
Your device and its enhancements may contain small parts. Keep them out of
the reach of small children.
IT Equipment Recycling Information
Acer is strongly committed to environmental protection and views recycling, in
the form of salvaging and disposal of used equipment, as one of the company's
top priorities in minimizing the burden placed on the environment.
We at Acer are very conscious of the environmental effects of our business and
strive to identify and provide the best working procedures to reduce the
environmental impact of our products.
For more information and help when recycling, please go to this website:
http://www.acer-group.com/public/Sustainability/
Visit www.acer-group.com for further information on the features and benefits
of our other products.
Disposal instructions
Do not throw this electronic device into the trash when discarding.
To minimize pollution and ensure utmost protection of the global
environment, please recycle. For more information on the Waste
from Electrical and Electronics Equipment (WEEE) regulations, visit
http://www.acer-group.com/public/Sustainability/
vii
LCD pixel statement
The LCD unit is produced with high-precision manufacturing techniques.
Nevertheless, some pixels may occasionally misfire or appear as black or
red dots. This has no effect on the recorded image and does not constitute
a malfunction.
This product has been shipped enabled for power management:
•
•
•
Activate display’s Sleep mode within 15 minutes of user inactivity.
Activate computer’s Sleep mode within 30 minutes of user inactivity.
Wake the computer from Sleep mode by pushing the power button.
Tips and information for comfortable use
Computer users may complain of eyestrain and headaches after prolonged use.
Users are also at risk of physical injury after long hours of working in front of a
computer. Long work periods, bad posture, poor work habits, stress,
inadequate working conditions, personal health and other factors greatly
increase the risk of physical injury.
Incorrect computer usage may lead to carpal tunnel syndrome, tendonitis,
tenosynovitis or other musculoskeletal disorders. The following symptoms may
appear in the hands, wrists, arms, shoulders, neck or back:
numbness, or a burning or tingling sensation
aching, soreness or tenderness
pain, swelling or throbbing
stiffness or tightness
coldness or weakness
If you have these symptoms, or any other recurring or persistent discomfort
and/or pain related to computer use, consult a physician immediately and
inform your company's health and safety department.
•
•
•
•
•
The following section provides tips for more comfortable computer use.
Finding your comfort zone
Find your comfort zone by adjusting the viewing angle of the monitor, using a
footrest, or raising your sitting height to achieve maximum comfort. Observe
the following tips:
•
•
•
refrain from staying too long in one fixed posture
avoid slouching forward and/or leaning backward
stand up and walk around regularly to remove the strain on your leg
muscles
viii
Taking care of your vision
Long viewing hours, wearing incorrect glasses or contact lenses, glare, excessive
room lighting, poorly focused screens, very small typefaces and low-contrast
displays could stress your eyes. The following sections provide suggestions on
how to reduce eyestrain.
Eyes
•
•
•
Rest your eyes frequently.
Give your eyes regular breaks by looking away from the monitor and
focusing on a distant point.
Blink frequently to keep your eyes from drying out.
Display
•
Keep your display clean.
•
•
•
•
•
Keep your head at a higher level than the top edge of the display so your
eyes point downward when looking at the middle of the display.
Adjust the display brightness and/or contrast to a comfortable level for
enhanced text readability and graphics clarity.
Eliminate glare and reflections by:
•
placing your display in such a way that the side faces the window or
any light source
•
•
•
minimizing room light by using drapes, shades or blinds
•
•
using a glare-reduction filter
using a task light
changing the display's viewing angle
using a display visor, such as a piece of cardboard extended from the
display's top front edge
Avoid adjusting your display to an awkward viewing angle.
Avoid looking at bright light sources, such as open windows, for extended
periods of time.
Developing good work habits
Develop the following work habits to make your computer use more relaxing
and productive:
•
Take short breaks regularly and often.
•
•
•
Perform some stretching exercises.
Breathe fresh air as often as possible.
Exercise regularly and maintain a healthy body.
TABLE OF CONTENTS
UNPACKING............................................................................................ 1
REMOVING THE STAND ARM FOR WALL MOUNT ............................... 2
ATTACHING THE BASE........................................................................... 3
SCREEN POSITION ADJUSTMENT .......................................................... 4
CONNECTING THE POWER CORD.......................................................... 6
SAFETY PRECAUTION............................................................................. 6
CLEANING YOUR MONITOR .................................................................. 6
POWER SAVING...................................................................................... 7
DDC......................................................................................................... 7
CONNECTOR PIN ASSIGNMENT............................................................. 8
Standard Timing Table .......................................................................... 9
INSTALLATION...................................................................................... 11
USER CONTROLS .................................................................................. 13
TROUBLESHOOTING ............................................................................ 24
UNPACKING
Please check the following items are present when you unpack the box, and
save the packing materials in case you will need to ship or transport the
monitor in future.

LCD Monitor


AC Power Cord


Quick Start Guide
HDMI Cable
(Optional)
USB Cable
(Optional)
EN-1

AC Adapter

DP Cable (Optional)
REMOVING THE STAND ARM FOR WALL MOUNT
Note: Carefully place the monitor face-down on a stable surface -- use
a cloth to avoid scratching the screen.
1.
2.
Detach and remove the VESA covers
with a flathead screwdriver.
Loosen and remove the screws with a
Phillips screwdriver, then lift and remove
the stand arm.
3.
Your monitor is ready for wall mount.
Note: If installing with a wall mounting kit, it is recommended to use
M4 x 10 (L) mm screws to fix your monitor on the wall.
EN-2
ATTACHING THE BASE
Note: Carefully place the monitor face-down on a stable surface -- use
a cloth to avoid scratching the screen.
1.
Attach the monitor stand arm to
the monitor. Ensure that the stand
arm is screwed tight onto the
monitor.
2.
Attach the VESA covers.
EN-3
SCREEN POSITION ADJUSTMENT
In order to optimize the best viewing position, you can adjust the height/tilt
of the monitor.
•
Tilt
Please see the illustration below for an example of the tilt range.
Only at the highest point can 35 degrees of recline be offered for the angle of
elevation.
o
-4
o
•
Height Adjustment
After pressing the top of the monitor then you can adjust the height of the
monitor.
1
2
130mm
EN-4
•
Swivel
With the built-in pedestal, you can swivel the monitor for the most
comfortable viewing angle.
EN-5
CONNECTING THE POWER CORD





Check first to make sure that the power cord you use is the correct type
required for your area.
This monitor has a universal power supply that allows operation in either
100/120V AC or 220/240 V AC voltage area. No user-adjustment is required.
Plug one end of the AC power cord to the adapter, and plug the other end
into an AC outlet.
For unit using at 120 V AC:
Use a UL Listed Cord Set, Type SVT wire and plug rated 10 A/125 V.
For unit using at 220/240 V AC (outside of U.S.):
Use a Cord Set consisting of H05VV-F cord and plug rated 10 A, 250 V. The
cord set should have the appropriate safety approvals for the country in
which the equipment will be installed.
SAFETY PRECAUTION







Avoid placing the monitor, or any other heavy object, on the power cord
to avoid damage to the cable.
Do not expose the monitor to rain, excessive moisture, or dust.
Do not cover the ventilation slots or openings of the monitor. Always put
the monitor in a place where there is adequate ventilation.
Avoid placing the monitor against a bright background or where sun-light
or other light sources may reflect on the face of the monitor. Place the
monitor just below eye level.
Handle with care when transporting the monitor.
Refrain from giving shock or scratch to the screen, as screen is fragile.
In order to prevent damage to the monitor, do not lift the monitor by its
base.
CLEANING YOUR MONITOR
Please carefully follow the below guidelines when cleaning the monitor.
 Always unplug the monitor before cleaning.
 Use a soft cloth to gently wipe the screen and cabinet front and sides.
 NEVER SPRAY OR POUR ANY LIQUID DIRECTLY ONTO THE SCREEN OR
CASE.
 PLEASE DO NOT USE ANY AMMONIA OR ALCOHOL-BASED CLEANERS ON
THE LCD DISPLAY SCREEN OR CASE.
 Acer will not be liable for damage resulting from use of any ammonia or
alcohol-based cleaners.
EN-6
POWER SAVING
The monitor will be driven into “Power Saving” mode by the control signal
from the display controller, as indicated by the amber-color power LED.
State
LED Light
ON
Blue
Power Saving Mode
Amber
The power saving states will be kept until a control signal has been detected
or the keyboard or mouse is activated. The recovery time from Active OFF
state back to ON state is around 3 seconds.
DDC
To make your installation easier, the monitor is able to Plug and Play with
your system if your system also supports DDC protocol. The DDC (Display Data
Channel) is a communication protocol through which the monitor
automatically informs the host system about its capabilities, for example,
supported resolutions and corresponding timing. The monitor supports
DDC2B standard.
EN-7
CONNECTOR PIN ASSIGNMENT
19-Pin Color Display Signal Cable*
PIN
Meaning
PIN
Meaning
1.
TMDS Data2+
10.
TMDS Clock+
2.
TMDS Data2 Shield
11.
TMDS Clock Shield
3.
TMDS Data2-
12.
TMDS Clock-
4.
TMDS Data1+
13.
CEC
5.
TMDS Data1 Shield
14.
Reserved (N.C. on device)
6.
TMDS Data1-
15.
SCL
7.
TMDS Data0+
16.
SDA
8.
TMDS Data0 Shield
17.
DDC/CEC Ground
9.
TMDS Data0-
18.
+5V Power
19.
Hot Plug Detect
* only for certain models
20-Pin Color Display Signal Cable
PIN
Description
PIN
Description
1.
Lane0(p)
11.
GND
2.
GND
12.
Lane3(n)
3.
Lane0(n)
13.
Config1
4.
Lane1(p)
14.
Config2
5.
GND
15.
AUX_CH (n)
6.
Lane1(n)
16.
GND
7.
Lane2(p)
17.
AUX_CH (p)
8.
GND
18.
Hot Plug Detect
9.
Lane3(n)
19.
DP Power_Return
10.
Lane3(p)
20.
DP Power
EN-8
Standard Timing Table
HDMI
Mode
Resolution
1
VGA
640 x 480
60
Hz
2
VGA
640 x 480P
59.94
Hz
3
VGA
640 x 480P
60
Hz
4
SDTV
720 x 576P
50
Hz
5
SDTV
720 x 480P
59.94
Hz
6
SDTV
720 x 480P
60
Hz
7
SVGA
800 x 600
60
Hz
8
XGA
1024 x 768
60
Hz
9
HD
1280 x 720P
50
Hz
10
HD
1280 x 720P
59.94
Hz
11
HD
1280 x 720P
60
Hz
12
FHD
1920 x 1080P
50
Hz
13
FHD
1920 x 1080P
59.94
Hz
14
FHD
1920 x 1080P
60
Hz
15
Wide QHD
3440 x 1440
50
Hz
EN-9
DP
Mode
Resolution
1
VGA
640 x 480
60
Hz
2
SVGA
800 x 600
60
Hz
3
XGA
1024 x 768
60
Hz
4
Wide QHD
3440 x 1440
50
Hz
5
Wide QHD
3440 x 1440
60
Hz
6
Wide QHD
3440 x 1440
85
Hz
7
Wide QHD
3440 x 1440
100
Hz
EN-10
INSTALLATION
To install the monitor to your host system, please follow the steps as given
below:
Steps
1. 1-1 Connect HDMI Cable (Only HDMI-input model)
a. Make sure both the monitor and computer are powered-OFF.
b. Connect the HDMI cable to the computer.
1-2 Connect DP Cable (Default input) (Only DP-input model)
a. Make sure both the monitor and computer are powered-OFF.
b. Connect the DP cable to the computer.
2. Connect the Audio Cable (Optional)
3. Connect the adapter
a. Connect the AC cord to the adapter.
b. Connect one end of the adapter to the monitor and the other end to
a properly grounded, AC outlet.
4. Power-ON Monitor and Computer
Power-ON the monitor first, then power-ON the computer.
This sequence is very important.
5. Select Power-off USB charge ON/OFF to enable/disable Power-off USB
charge function.
EN-11
6. If the monitor still does not function properly, please refer to the
troubleshooting section to diagnose the problem.
DC
HDMI
DP
DP IN
EN-12
HDMI
USER CONTROLS
Base Controls
Icon
Item
Description
Power button/
indicator
Turns the monitor on/off. Blue indicates power on.
Amber indicates standby/power saving mode.
OSD functions
Press to view the OSD. Press again to enter a selection
in the OSD.
Input button
Press to toggle input sources.
Volume button Press to activate the volume sliding scale.
Brightness
Press the key to open the Brightness control and set it
to your preferred level.
Mode
Press to trigger Mode control.
EN-13
Adjusting the OSD settings
Note: The following content is for general reference only. Actual
product specifications may vary.
The OSD (on-screen display) can be used for adjusting the settings of your LCD
Monitor. Press the MENU key to open the OSD. You can use the OSD to adjust
the picture quality, OSD position and general settings. For advanced settings,
please refer to following page:
Main Page
1.
2.
3.
4.
5.
Mode
Brightness
Volume
Input selection
Function menu
Turn Mode on or off
Open the Mode control and turn Mode on or off using the adjustment arrows
(OFF/ON), and select which profile to use (Please see the OSD section for more
information).
Adjusting the Brightness setting
Open the Brightness control and select the brightness setting using the arrows.
When you are done, use
to go back one level.
EN-14
Adjusting the Volume
Open the Volume control and set the volume using the arrows. When you are
done, use
to go back one level.
Note: Adjustment of the volume control as well as the equalizer to
other settings than the center position may increase the ear/
headphone output voltage and therefore the sound pressure level.
Selecting the Input
Open the input control and select HDMI or DisplayPort. When you are done,
use
to go back one level.
EN-15
The Function page
Open the Function page to select Picture, Color, Audio, Gaming, OSD or
System functions, and adjust the settings which you want using the arrows.
You can also view your monitor’s system information from this page. When
you are done, use
to go back one level.
Adjusting the Picture
1.
Press the MENU key to bring up the OSD.
2.
Using the / keys, select Picture from the OSD. Then navigate to the
picture element you wish to adjust.
3.
Use the / keys to adjust the sliding scales.
4.
The Picture menu can be used to adjust the Acer eColor, Blue Light,
Brightness, Adaptive contrast, Contrast, and Dark Boost.
5.
Brightness: Adjust the brightness from 0 to 100.
Note: Adjusts the balance between light and dark shades.
6.
Contrast: Adjust the contrast from 0 to 100.
Note: Sets the degree of difference between light and dark areas.
7.
Blue Light: filter out blue light by adjusting different Blue Light showing
ratio - 80%, 70%, 60%, 50%.
Note: Higher values allow more blue light through. For the best
protection, select a lower value.
EN-16
8.
Dark Boost: This boosts the amplitude of the dark color levels of the
display– blacks will be less black. The higher the level, the higher the
boost.
9.
Adaptive Contrast: This method usually increases the global contrast of
many images, especially when the usable data of the image is
represented by close contrast values. This allows for areas of lower local
contrast to gain a higher contrast. The method is useful in images with
backgrounds and foregrounds that are both bright or both dark. In
particular, the method can lead to better views of bone structure in x-ray
images, and to better detail in photographs that are over or underexposed.
Adjusting the Color
1.
Press the MENU key to open the OSD.
2.
Using the / keys, select Color from the OSD. Then navigate to the
picture element you wish to adjust.
3.
Use the / keys to select setting.
4.
Gamma mode allows you to adjust the luminance tone. The default value
is 2.2 (standard value for Windows).
5.
Color temperature: Default is warm. You can choose Cool, Warm,
Bluelight or User.
6.
sRGB mode is for getting better color matching representation with the
peripheral device, such as DSCs or printers.
7.
Saturate: Color brightness can be changed by 0~200 adjustment.
8.
6-axis color: Chroma of red, green, blue, cyan, yellow, and magenta can
be independently adjusted from 0~255, changing the color quality of the
image.
EN-17
Adjusting the Audio
1.
Press the MENU key to open the OSD.
2.
Using the / keys, select Audio from the OSD. Then navigate to the
picture element you wish to adjust.
3.
Use the / keys to select setting.
4.
Volume: Adjusts the volume.
EN-18
Adjusting the Gaming
1.
Press the MENU key to open the OSD.
2.
Using the / keys, select Gaming from the OSD. Then navigate to the
picture element you wish to adjust.
3.
Use the / keys to select setting.
4.
Over Drive: Select Off, Normal, or Extreme.
5.
Aim point: Show an Aim point on the screen for shooting games.
Adjusting the OSD
1.
Press the MENU key to open the OSD.
2.
Using the / keys, select OSD from the OSD. Then navigate to the
setting you wish to change.
3.
Use the / keys to adjust any sliding scales.
4.
Language: Set the OSD menu language.
EN-19
5.
OSD Timeout: Adjust the delay before turning the off the OSD menu.
6.
Transparency: Select the transparency when using gaming mode. The
transparency can be 0% (OFF), 20%, 40%, 60%, or 80%.
7.
Refresh rate num: Display the panel’s current refresh rate on the screen.
EN-20
Adjusting the System
1.
The System menu can be used to select settings such as Input, Wide
Mode, and Power LED.
2.
Press the MENU key to open the OSD.
3.
Using the / keys, select System from the OSD. Then navigate to the
setting you wish to adjust.
4.
Use the / keys to select the setting.
5.
Input: Select the source from DP In or HDMI.
6.
Hot Key Assignment: Select the function of Hotkey 1 or Hotkey 2.
7.
Wide Mode: You can select which screen aspect you are using. The
options are Aspect and 1:1.
8.
Deep Sleep: Default is on. When the function is on, with no HDMI or DP
input after 13 minutes, the monitor will go to sleep mode. When the
function is off, with no HDMI or DP input, the monitor will not go to
sleep mode
Note: Pressing any button (except the Power button) on the monitor
may also wake up the monitor after it goes into deep sleep.
9.
Quick Start Mode: Enable monitor rapidly
10. Power LED: You can set the power LED indicator to glow, go dimmer, or
go off.
11. Power-off USB charge: Turn On or Off.
EN-21
Product information
1.
Press the MENU key to open the OSD.
2.
Using the / keys, select Information to view the basic information for
your monitor and current input.
3.
Reset: Resets all settings to the factory defaults.
EN-22
G-SYNC Experience:
For the following resolution:
3440 x 1440@50 Hz
3440 x 1440@60 Hz (DP only)
3440 x 1440@85 Hz (DP only)
3440 x 1440@100 Hz (DP only)
G-SYNC requires an NVIDIA GeForce GTX650Ti BOOST or higher GeForce GTX
graphics card with a DisplayPort output. For more information, visit the
nVidia® Website: http://www.nvidia.com/
EN-23
TROUBLESHOOTING
Before sending your LCD monitor for servicing, please check the troubleshooting list below to see if you can self-diagnose the problem.
(HDMI/DP Mode)
Problems
Current Status
Remedy

LED ON


LED OFF
No Picture

LED displays amber
color


Abnormal Sound
(Only Audio-Input
model)
(Optional)
No sound, or sound
level is too low
EN-24

Using OSD, adjust brightness
and contrast to maximum or
reset to their default settings.
Check the power switch.
Check if AC power cord is
properly connected to the
monitor.
Check if video signal cable is
properly connected at the back
of monitor.
Check if the power of computer
system is ON.
Check the audio cable with the
host PC is connected.
Check if the volume setup of the
host PC is in minimum position
and try to raise the volume
level.
EN-25
Acer America Corporation
333 West San Carlos St.,
Suite 1500
San Jose, CA 95110
U. S. A.
Tel : 254-298-4000
Fax : 254-298-4147
www.acer.com
Federal Communications Commission
Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
The following local Manufacturer /Importer is responsible for this declaration:
Product:
LCD Monitor
Model Number:
Z35P
SKU Number:
Z35P xxxxxx
(“x” = 0~9, a ~ z, or A ~ Z)
Name of Responsible Party:
Acer America Corporation
Address of Responsible Party:
333 West San Carlos St.
Suite 1500
San Jose, CA 95110
U. S. A.
Contact Person:
Acer Representative
Phone No.:
254-298-4000
Fax No.:
254-298-4147
EN-26
Download PDF