Acer | KA241 | Acer KA241 Quick Start Guide

Acer LCD Monitor Quick Start Guide (QSG)
Please read the following instructions carefully.
To clean the LCD monitor screen:
Turn off the LCD monitor and unplug the power cord.
Spray a non-solvent cleaning solution onto a rag and clean the screen gently.
Do not place the LCD monitor near a window. Exposing the monitor to rain, moisture or sunlight can severely damage
Do not apply pressure to the LCD screen. Excessive pressure may cause permanent damage to the display.
Do not remove the cover or attempt to service this unit yourself. An authorized technician should perform servicing of
any nature.
Store the LCD monitor in a room with a temperature of -20° to 60° C (-4° to140° F). Storing the LCD monitor outside
this range may result in permanent damage.
Immediately unplug your monitor and call an authorized technician if any of the following circumstances occur:
Monitor-to-PC signal cable is frayed or damaged.
Liquid spills onto the LCD monitor or the monitor is exposed to rain.
The LCD monitor or case is damaged.
Package contents
DVI cable
Quick start
(optional) (optional)
User Guide
Attaching the monitor to the base
Remove the monitor from the packaging.
Attach the footstand to the base. (for selected models).
Turn clockwise to lock. Ensure that the base in locked onto the stand. (for selected models)
Secure the base to the stand by turning the screw using the intergrated tab or a suitable coin. (for selected models)
Connecting your monitor to a computer
Turn off your computer and unplug your computer's power cord.
Connect the signal cable to the VGA (optional) and /or DVI-D
(optional) and/or HDMI (optional) input socket of the monitor, and
the DVI-D (optional) and/or HDMI (optional) output socket of the
graphics card on the computer. Then tighten the thumbscrews on
the signal cable connector.
Insert the monitor power cable into the power port at the back of the
Plug the power cords of your computer and your monitor into a
nearby electrical outlet.
Important safety instructions
External controls
Power button
Turns the monitor on/off. Blue indicates power on. Amber indicates
standby/ power saving mode.
Minus / Plus
If the OSD is active, press the Minus or Plus buttons to toggle
between the OSD options. If the OSD is inactive, press the Minus or
Plus buttons to adjust the volume. (Optional)
OSD functions Press to view the OSD. Press again to enter a selection in the OSD.
If the OSD is active, press Auto to exit the OSD. Once the OSD is
inactive, press Auto and the monitor will automatically optimize the
display position, focus, and clock of your display.
Empowering a. When the OSD menu is active, this button will act as the exit key (
exit OSD menu).
b. When the OSD menu is inactive, press this button to select
scenari o mode.
Regulations and safety notices
FCC notices
This device has been tested and found to comply with the limits for a Class B digital device pursuant to
Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This device generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this device does cause harmful interference to radio or television reception, which can be
determined by turning the device off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the device and receiver.
Connect the device into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/television technician for help.
CE declaration of conformity
Hereby, Acer Inc., declares that this LCD monitor is in compliance with the essential requirements and
other relevant provisions of EMC Directive 2014/30/EU, Low Voltage Directive 2014/35/EU, and RoHS
Directive 2011/65/EU and Directive 2009/125/EC with regard to establishing a framework for the setting
of ecodesign requirements for energy-related product.
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables to maintain compliance
with EMC regulations.
Notice: Peripheral devices
Only peripherals (input/output devices, terminals, printers, etc.) certified to comply with the Class B
limits may be attached to this equipment. Operation with non-certified peripherals is likely to result in
interference to radio and TV reception.
Changes or modifications not expressly approved by the manufacturer could void the user authority,
which is granted by the Federal Communications Commission, to operate this product.
In order to prevent damage to the monitor, do not lift the monitor by its base.
Operation conditions
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Notice: Canadian users
Download PDF