Acer | CB240HYK | Acer CB240HYK User Manual

Acer LCD Monitor
User’s Guide
Copyright © 2015. Acer Incorporated.
All Rights Reserved.
Acer LCD Monitor User’s Guide
Original Issue: 01/2015
Changes may be made periodically to the information in this publication without obligation to notify
any person of such revisions or changes. Such changes will be incorporated in new editions of this
manual or supplementary documents and publications. This company makes no representations or
warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims
the implied warranties of merchantability or fitness for a particular purpose.
Record the model number, serial number, purchase date and place of purchase information in the
space provided below. The serial number and model number are recorded on the label affixed to
your computer. All correspondence concerning your unit should include the serial number, model
number and purchase information.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any
form or by any means, electronically, mechanically, by photocopy, recording or otherwise, without
the prior written permission of Acer Incorporated.
Acer LCD Monitor User’s Guide
Model number: __________________________________
Serial number: ___________________________________
Date of purchase: ________________________________
Place of purchase: ________________________________
Acer and the Acer logo are registered trademarks of Acer Incorporated. Other companies’ product
names or trademarks are used herein for identification purposes only and belong to their respective
companies.
Special notes on LCD monitors
The following are normal with the LCD monitor and do not indicate a problem.
•
Due to the nature of the fluorescent light, the screen may flicker during initial
use. Turn off the power switch and then turn it on again to make sure the flicker
disappears.
•
You may find slightly uneven brightness on the screen depending on the desktop
pattern you use.
•
The LCD screen has 99.99% or more effective pixels. It may include blemishes of
0.01% or less such as a missing pixel or a pixel lit all the time.
•
Due to the nature of the LCD screen, an afterimage of the previous screen may
remain after switching the image, when the same image is displayed for hours. In
this case, the screen is recovered slowly by changing the image or turning off the
power switch for a few hours.
Information for your safety and
comfort
Safety instructions
Read these instructions carefully. Keep this document for future reference. Follow all
warnings and instructions marked on the product.
Cleaning your monitor
Please carefully follow these guidelines when cleaning the monitor:
•
Always unplug the monitor before cleaning.
•
Use a soft cloth to wipe the screen and cabinet front and sides.
Connecting/disconnecting the device
Observe the following guidelines when connecting and disconnecting power from the
LCD monitor:
•
Make sure the monitor is attached to its base before connecting the power cord to
the AC power outlet.
•
Make sure both the LCD monitor and the computer are turned off before
connecting any cable or unplugging the power cord.
•
If the system has multiple sources of power, disconnect power from the system by
unplugging all power cords from the power supplies.
iii
Accessibility
Be sure that the power outlet you plug the power cord into is easily accessible and
located as close to the equipment operator as possible. When you need to disconnect
power from the equipment, be sure to unplug the power cord from the electrical outlet.
Safe listening
To protect your hearing, follow these instructions.
•
Gradually increase the volume until you can hear it clearly and comfortably and
without distortion.
•
After setting the volume level, do not increase it after your ears have adjusted.
•
Limit the amount of time listening to music at high volume.
•
Avoid turning up the volume to block out noisy surroundings.
•
Turn the volume down if you can’t hear people speaking near you.
Warnings
•
Do not use this product near water.
•
Do not place this product on an unstable cart, stand or table. If the product falls, it
could be seriously damaged.
•
Slots and openings are provided for ventilation to ensure reliable operation of the
product and to protect it from overheating. These openings must not be blocked
or covered. The openings should never be blocked by placing the product on a bed,
sofa, rug or other similar surface. This product should never be placed near or over
a radiator or heat register, or in a built-in installation unless proper ventilation is
provided.
•
Never push objects of any kind into this product through cabinet slots as they may
touch dangerous voltage points or short-out parts that could result in a fire or
electric shock. Never spill liquid of any kind onto or into the product.
•
To avoid damage of internal components and to prevent battery leakage, do not
place the product on a vibrating surface.
•
Never use it under sporting, exercising, or any vibrating environment which will
probably cause unexpected short current or damage internal devices.
“For displays with glossy bezels the user should consider the placement of the display as
the bezel may cause disturbing reflections from surrounding light and bright surfaces.”
Using electrical power
iv
•
This product should be operated from the type of power indicated on the marking
label. If you are not sure of the type of power available, consult your dealer or local
power company.
•
Do not allow anything to rest on the power cord. Do not locate this product where
people will walk on the cord.
•
•
•
If an extension cord is used with this product, make sure that the total ampere
rating of the equipment plugged into the extension cord does not exceed the
extension cord ampere rating. Also, make sure that the total rating of all products
plugged into the wall outlet does not exceed the fuse rating.
Do not overload a power outlet, strip or receptacle by plugging in too many
devices. The overall system load must not exceed 80% of the branch circuit rating.
If power strips are used, the load should not exceed 80% of the power strip’s input
rating.
This product’s power cord is equipped with a three-wire grounded plug. The plug
only fits in a grounded power outlet. Make sure the power outlet is properly
grounded before inserting the power cord plug. Do not insert the plug into a nongrounded power outlet. Contact your electrician for details.
Warning! The grounding pin is a safety feature. Using a power
outlet that is not properly grounded may result in electric
shock and/or injury.
Note: The grounding pin also provides good protection from
unexpected noise produced by other nearby electrical devices that
may interfere with the performance of this product.
•
Use the product only with the supplied power supply cord set. If you need to
replace the power cord set, make sure that the new power cord meets the
following requirements: detachable type, UL listed/CSA certified, type SPT-2, rated
7 A 125 V minimum, VDE approved or its equivalent, 4.5 meters (15 feet) maximum
length.
Product servicing
Do not attempt to service this product yourself, as opening or removing covers may
expose you to dangerous voltage points or other risks. Refer all servicing to qualified
service personnel.
Unplug this product from the wall outlet and refer servicing to qualified service
personnel when:
•
the power cord or plug is damaged, cut or frayed
•
liquid was spilled into the product
•
the product was exposed to rain or water
•
the product has been dropped or the case has been damaged
•
the product exhibits a distinct change in performance, indicating a need for service
•
the product does not operate normally after following the operating instructions
v
Note: Adjust only those controls that are covered by the operating
instructions, since improper adjustment of other controls may result
in damage and will often require extensive work by a qualified
technician to restore the product to normal condition.
Potentially explosive environments
Switch off your device in any area with a potentially explosive atmosphere and obey all
signs and instructions. Potentially explosive atmospheres include areas where you would
normally be advised to turn off your vehicle engine. Sparks in such areas could cause
an explosion or fire resulting in bodily injury or even death. Switch off the device near
gas pumps at service stations. Observe restrictions on the use of radio equipment in fuel
depots, storage and distribution areas; chemical plants; or where blasting operations are
in progress. Areas with a potentially explosive atmosphere are often, but not always,
marked. They include below deck on boats, chemical transfer or storage facilities,
vehicles using liquefied petroleum gas (such as propane or butane), and areas where the
air contains chemicals or particles such as grain, dust or metal powders.
Additional safety information
Your device and its enhancements may contain small parts. Keep them out of the reach
of small children.
IT Equipment Recycling Information
Acer is strongly committed to environmental protection and views recycling, in the form
of salvaging and disposal of used equipment, as one of the company’s top priorities in
minimizing the burden placed on the environment.
We at Acer are very conscious of the environmental effects of our business and strive to
identify and provide the best working procedures to reduce the environmental impact
of our products.
For more information and help when recycling, please go to this website:
http://www.acer-group.com/public/Sustainability
Visit www.acer-group.com for further information on the features and benefits of our
other products.
vi
Disposal instructions
Do not throw this electronic device into the trash when discarding. To minimize
pollution and ensure utmost protection of the global environment, please recycle.
For more information on the Waste from Electrical and Electronics Equipment (WEEE)
regulations, visit http://www.acer-group.com/public/Sustainability
LCD pixel statement
The LCD unit is produced with high-precision manufacturing techniques. Nevertheless,
some pixels may occasionally misfire or appear as black or red dots. This has no effect on
the recorded image and does not constitute a malfunction.
This product has been shipped enabled for power management:
•
Activate display’s Sleep mode within 15 minutes of user inactivity.
•
Activate computer’s Sleep mode within 30 minutes of user inactivity.
•
Wake the computer from Sleep mode by pushing the power button.
Tips and information for comfortable use
Computer users may complain of eyestrain and headaches after prolonged use. Users are
also at risk of physical injury after long hours of working in front of a computer. Long
work periods, bad posture, poor work habits, stress, inadequate working conditions,
personal health and other factors greatly increase the risk of physical injury.
Incorrect computer usage may lead to carpal tunnel syndrome, tendonitis, tenosynovitis
or other musculoskeletal disorders. The following symptoms may appear in the hands,
wrists, arms, shoulders, neck or back:
•
numbness, or a burning or tingling sensation
•
aching, soreness or tenderness
•
pain, swelling or throbbing
•
stiffness or tightness
•
coldness or weakness
If you have these symptoms, or any other recurring or persistent discomfort and/or pain
related to computer use, consult a physician immediately and inform your company’s
health and safety department.
The following section provides tips for more comfortable computer use.
vii
Finding your comfort zone
Find your comfort zone by adjusting the viewing angle of the monitor, using a footrest,
or raising your sitting height to achieve maximum comfort. Observe the following tips:
•
refrain from staying too long in one fixed posture
•
avoid slouching forward and/or leaning backward
•
stand up and walk around regularly to remove the strain on your leg muscles
Taking care of your vision
Long viewing hours, wearing incorrect glasses or contact lenses, glare, excessive room
lighting, poorly focused screens, very small typefaces and low-contrast displays could
stress your eyes. The following sections provide suggestions on how to reduce eyestrain.
Eyes
•
Rest your eyes frequently.
•
Give your eyes regular breaks by looking away from the monitor and focusing on a
distant point.
•
Blink frequently to keep your eyes from drying out.
•
For displays with glossy bezels the user should consider the placement of the display
as the bezel may cause disturbing reflections from surrounding light and bright
surfaces.
Display
viii
•
Keep your display clean.
•
Keep your head at a higher level than the top edge of the display so your eyes
point downward when looking at the middle of the display.
•
Adjust the display brightness and/or contrast to a comfortable level for enhanced
text readability and graphics clarity.
•
Eliminate glare and reflections by:
•
lacing your display in such a way that the side faces the window or any light
p
source
•
minimizing room light by using drapes, shades or blinds
•
using a task light
•
changing the display’s viewing angle
•
using a glare-reduction filter
•
sing a display visor, such as a piece of cardboard extended from the display’s
u
top front edge
•
Avoid adjusting your display to an awkward viewing angle.
•
Avoid looking at bright light sources, such as open windows, for extended periods
of time.
Developing good work habits
Develop the following work habits to make your computer use more relaxing and
productive:
•
Take short breaks regularly and often.
•
Perform some stretching exercises.
•
Breathe fresh air as often as possible.
•
Exercise regularly and maintain a healthy body.
ix
Declaration of Conformity
We,
Acer Incorporated
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi, New Taipei City 221, Taiwan
Contact Person: Mr. RU Jan, e-mail:ru.jan@acer.com
And,
Acer Italy s.r.l
Via Lepetit, 40, 20020 Lainate (MI) Italy
Tel: +39-02-939-921 ,Fax: +39-02 9399-2913
www.acer.it






Declare under our own responsibility that the product:
Product:
LCD Monitor
Trade Name:
Acer
Model Number:
CB240HYK
SKU Number:
CB240HYK xxxxxx;
(“x” = 0~9, a ~ z, A ~ Z, or blank)
To which this declaration refers conforms to the relevant standard or other standardizing documents:
EN55022:2010 Class B; EN55024:2010
EN 61000-3-2:2006+A1:2009+A2:2009, Class D
EN61000-3-3:2008
EN60950-1:2006/A11:2009/A1:2010+A12:2011
Regulation (EC) No. 1275/ 2008; EN 50564:2011; IEC 62301:2011
EN50581:2012
We hereby declare above product is in compliance with the essential requirements and other relevant
provisions of EMC Directive 2004/108/EC, Low Voltage Directive 2006/95/EC, and RoHS Directive
2011/65/EU and Directive 2009/125/EC with regard to establishing a framework for the setting of ecodesign
requirements for energy-related product.
Year to begin affixing CE marking 2015.
_______________________________
RU Jan / Sr. Manager
Regulation, Acer Inc.
Feb. 13, 2015
Date
Acer America Corporation
333 West San Carlos St., San Jose
Suite 1500
CA 95110, U. S. A.
Tel : 254-298-4000
Fax : 254-298-4147
www.acer.com
Federal Communications Commission
Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
The following local Manufacturer /Importer is responsible for this declaration:
Product:
LCD Monitor
Model Number:
CB240HYK
SKU Number:
B240HYK xxxxxx (“x”
C
= 0~9, a ~ z, or A ~ Z)
Name of Responsible Party:
Acer America
Corporation
Address of Responsible Party:
3 33 West San Carlos St.
Suite 1500 San Jose, CA
95110 U. S. A.
Contact Person:
Acer Representative
Phone No.:
254-298-4000
Fax No.:
254-298-4147
Special notes on LCD monitors
Information for your safety and comfort
iii
iii
Safety instructions
iii
Cleaning your monitor
iii
Connecting/disconnecting the device
iii
Accessibilityiv
Safe listening
iv
Warningsiv
Using electrical power
iv
Product servicing
v
Potentially explosive environments
vi
Additional safety information
vi
IT Equipment Recycling Information
vi
Disposal instructions
vii
LCD pixel statement
vii
Tips and information for comfortable use
vii
Finding your comfort zone
viii
Taking care of your vision
viii
Developing good work habits
ix
Declaration of Conformity
Federal Communications Commission
Unpacking
ATTACHING/ REMOVING THE BASE
Screen position adjustment
Connecting the Power cord Power saving
Display Data Channel (DDC)
Connector pin assignment
1
2
3
5
5
5
6
Standard timing table
8
Installation9
Users controls
Acer eColor Management
Adjusting the OSD settings
Adjusting the picture quality
Adjusting the OSD position
Adjusting the setting
Product information
10
11
12
12
13
14
15
DVI(Dual Link) / HDMI mode
DP mode
16
16
Troubleshooting16
Unpacking
LCD monitor
Quick start guide
DP cable (Optional)
HDMI cable (Optional)
DVI(Dual Link) cable
(Optional)
AC Power cord
Audio cable (Optional)
MHL cable (Optional)
English
Please check that the following items are present when you unpack the box, and save
the packing materials in case you need to ship or transport the monitor in the future.
1
ATTACHING/ REMOVING THE BASE
English
Install: Align the base with the stand and push the base towards the top of
the monitor, and then rotate the base clockwise. Tighten the screw clockwise.
Remove: Reverse the steps to remove the base.
Warning:
• Actions below are not allowed while moving and walking: high adjustment, tilt,
swivel and pivot because of safety requirement.
• To prevent fragile panel broken, when moving and disassembling the product , it
must pull the monitor head to the top at first and place the horizontal direction on
the table.
2
SCREEN POSITION ADJUSTMENT
•
English
In oder to optimize the best viewing position, you can adjust the height/tilt/ swivel/pivot
of the monitor.
Height Adjustment
After pressing the top of the monitor then you can adjust the height of the monitor.
1
2
150mm
•
Tilt
Please see the illustration below for an example of the tilt range.
Only at the highest point can 35 degrees of recline be offered for the angle of elevation.
5o o
3
•
Swivel
English
With the built-in pedestal, you can swivel the monitor for the most comfortable viewing
angle.
o
•
Monitor Pivot
Before rotating the display,lift it to the top position and then push it back to the utmost
degree.
Rotate clockwise until the monitor stops at 90°.
90o
150
4
•
Check first to make sure that the power cord you use is the correct type required
for your area.
•
The monitor has a universal power supply that allows operation in either 100/120 V
AC or 220/240 V AC voltage area. No user-adjustment is required.
•
Plug one end of the power cord to the AC inlet, and plug the other end into an AC
outlet.
•
For units using 120 V AC:
Use a UL-listed cord set, type SVT wire and plug rated 10 A/125 V.
•
For units using 220/240 V AC:
Use a cord set consisting of H05VV-F cord and plug rated 10 A/250 V. The cord
set should have the appropriate safety approvals for the country in which the
equipment will be installed.
English
Connecting the Power cord
Power saving
The monitor will be switched to “power saving” mode by the control signal from the
display controller, as indicated by the amber-colored power LED.
Mode
LED light
On
Blue
Power saving
Amber
The power saving mode will be kept until a control signal has been detected or the
keyboard or mouse is activated. The recovery time from “power saving” mode back to
“on” is around 3 seconds.
Display Data Channel (DDC)
To make installation easier, so long as your system supports the DDC protocol, the
monitor is able to plug-and-play. The DDC is a communication protocol through which
the monitor automatically informs the host system about its capabilities; for example,
supported resolutions and corresponding timing. The monitor supports the DDC2B
standard.
5
Connector pin assignment
English
19-pin color display signal cable
19 1715 13 11 9 7 5 3 1
18 16 1412 10 8 6 4 2
PIN No.
Description
PIN No.
1
TMDS Data2+
2
Description
TMDS Data2 Shield
3
TMDS Data2-
4
TMDS Data1+
5
TMDS Data1 Shield
6
TMDS Data1-
7
TMDS Data0+
8
TMDS Data0 Shield
9
TMDS Data0-
10
TMDS Clock+
11
TMDS Clock Shield
12
TMDS Clock-
13
CEC
14
Reserved (N.C. on device)
15
SCL
16
SDA
17
DDC/CEC Ground
18
+5V Power
19
Hot Plug Detect
*only for certain models
19 1715 13 11 9 7 5 3 1
18 16 1412 10 8 6 4 2
20-pin color MHL cable*
PIN No.
Description
Description
MHL+
9
MHL-
18
VBUS
19
CBUS
5
GND
11
GND
17
GND
*Only for MHL models
6
PIN No.
7
English
24-pin color display signal cable*
PIN No.
1
2
3
Description
TMDS data 2TMDS data 2+
TMDS data 2/4 shield
PIN No.
13
14
15
Description
TMDS data 3+
+5 V power
GND (return for +5 V hsync.vsync)
4
5
TMDS data 4TMDS data 4+
16
17
Hot-plug detection
TMDS data 0-
6
7
DDC clock
DDC data
18
19
TMDS data 0+
TMDS data 0/5 shield
8
9
10
11
12
NC
TMDS data 1TMDS data 1+
TMDS data 1/3 shield
TMDS data 3-
20
21
22
23
24
TMDS data 5TMDS data 5+
TMDS clock shield
TMDS clock+
DDC TMDS clock-
20-pin color display signal cable*
PIN No.
1
2
Lane0(p)
GND
Description
PIN No.
11
12
GND
Lane3(n)
Description
3
Lane0(n)
13
Config1
4
5
Lane1(p)
GND
14
15
Config2
AUX_CH (n)
6
7
Lane1(n)
Lane2(p)
16
17
GND
AUX_CH (p)
8
GND
18
Hot Plug Detect
9
Lane3(n)
19
DP Power_Return
10
Lane3(p)
20
DP Power
* only for certain models
7
Standard timing table
English
Mode
8
1
VGA
640x480@60Hz
2
VGA
640x480@72Hz
3
VGA
640x480@75Hz
4
MAC
640x480@66.66Hz
5
VESA
720x400@70Hz
6
SVGA
800x600@56Hz
7
SVGA
800x600@60Hz
8
SVGA
800x600@72Hz
9
SVGA
800x600@75Hz
10
MAC
832x624@74.55Hz
11
XGA
1024x768@60Hz
12
XGA
1024x768@70Hz
13
XGA
1024x768@75Hz
14
MAC
1152x870@75Hz
15
VESA
1152x864@75Hz
16
VESA
1280x960@60Hz
17
SXGA
1280x1024@60Hz
18
SXGA
1280x1024@75Hz
19
VESA
1280x720@60Hz
20
WXGA
1280x800@60Hz
21
WXGA+
1440x900@60Hz
22
WSXGA+
1680x1050@60Hz
23
FHD
1920x1080@60Hz
24
UHD
3840x2160@30Hz
25*
UHD
3840x2160@60Hz
*DisplayPort
and HDMI 2.0 only
Installation
To install the monitor on your host system, please follow the steps below:
English
Steps
1 Connect the video cable
a
Make sure both the monitor and computer are switched off.
b
Connect the digital cable (only for dual-input models).
(1) Make sure both the monitor and computer are switched off.
(2) C
onnect one end of the 24-pin DVI(Dual Link) cable to the back of the
monitor and the other end to the computer’s port.
c
d
Connect the digital cable (only for DP models).
(1)
Make sure both the monitor and computer are switched off.
(2)
Connect one end of the 20-pin DP cable to the back of the monitor and the
other end to the computer’s port.
HDMI Cable (Only HDMI or MHL Input Model)
(1) Make sure both the monitor and computer are powered-OFF.
(2) Connect the HDMI or MHL cable to the computer.
2
Connect the power cord
Connect the power cord to the monitor, then to a properly grounded AC outlet.
3 O
ptional:Connect the audio input socket(AUDIO IN) of the LCD monitor and the lineout port on the computer with the audio cable.
4 Turn on the monitor and computer
Turn on the monitor first, then the computer. This sequence is very important.
5 If the monitor does not function properly, please refer to the troubleshooting section
to diagnose the problem.
HDMI
HDMI
AUDIO
AUDIO IN
DP
HDMI
DVI(Dual Link)
In order to prevent damage to the monitor, do not lift the monitor by its base.
9
Users controls
Power Switch / Power LED:
To turn the monitor ON or OFF.
Lights up to indicate the power is turned ON.
Using the Shortcut Menu
AUTO
Input
Press the function button to open the shortcut menu. The shortcut menu lets you quickly
select the most commonly accessed settings.
Empowering:
Press the Empowering Key to open the Acer eColor Management OSD and access the
scenario modes.
AUTO Exit OSD
If the OSD is active, press AUTO to exit the OSD.
MENU OSD functions
Press this botton to activate the OSD menu.
INPUT Input Key
Use Input key to select from different video sources that may be connected to
your monitor.
(a) HDMI input
(b) DVI(Dual Link) input
(c) DP input
As you cycle through the sources you will see the following messages on right topside of
screen to indicate currently selected input source. It may take 1 or 2 seconds for the image
to appear.
HDMI or DVI(Dual Link) or DP
10
If either DVI(Dual Link) input is selected ,but the DVI(Dual Link) cables are not
connected, a floating dialog box indicates:“No Cable Connect” or “No Signal”
Acer eColor Management
mpowering Technology
User
ECO
Standard Graphics
Movie
Adjust/Exit
Operation instructions
Step 1: Press “ “ Key to open the Acer eColor Management OSD and access the scenario
modes
Step 2: Press “
“
/ or/“
” to select the mode Features and Benefits
Step 3: Press “ AUTO “ Key to confirm the mode and exit the eColor menu.
Features and benefits
Main Menu
icon
Sub Menu
icon
Sub Menu
item
N/A
User
mode
N/A
ECO mode
N/A
Standard
mode
N/A
Grahpic
mode
N/A
Movie
mode
Description
User defined. Settings can be fine-tuned to
suit any situation
Adjusts the settings to reduce power
consumption.
Default Setting. Reflects native display
capability
Enhances colors and emphasize fine detail.
Pictures and photographs appear in vibrant
colors with sharp detail.
Displays scenes in clearest detail. Presents
great visuals , even in unsuitably - lit
environments.
11
Adjusting the OSD settings
Note: The following content is for general reference only. Actual
product specifications may vary.
The OSD can be used for adjusting the settings of your LCD Monitor.
Press the MENU key to open the OSD. You can use the OSD to adjust the picture quality,
OSD position and general settings. For advanced settings, please refer to following page:
Adjusting the picture quality
Picture
Picture
Acer eColor Management
Blue Light
Brightness
100
Contrast
6-axis Hue
50
Colour Temp
Blue Light
Gamma
2.2
Super Sharpness
Off
sRGB mode
Off
Exit
12
6-axis Saturate
Off
Enter
Exit
Enter
1.
Press the MENU key to bring up the OSD.
2.
Using the //
keys, select
element you wish to adjust.
3.
Use the
4.
The Picture menu can be used to adjust the Brightness, Contrast, Colour Temp,
6-axis Saturation, 6-axis Hue and other image-related qualities.
5.
6-axis Saturate: Adjust saturation of red, green, blue, yellow, magenta and cyan
6-axis Hue: Adjust hue for red, green, blue, yellow, magenta and cyan.
6.
Gamma mode is for user to adjust Tone of Liminance. The default value is 2.2
(Standard value for Windows)
7.
sRGB mode is for user such as DSCs, printers, photographer to get better color
matching representation with the peripheral device.
8.
Super Sharpness technology can simulate high-resolution images by boosting
the pixel density of the original source. It can make the image more sharper and
clear.
9.
Blue Light: filter out blue light by adjusting different Blue Light showing ratio 80%, 70%, 60%, 50%.
//
Picture from the OSD. Then navigate to the picture
keys to adjust the sliding scales.
Adjusting the OSD position
OSD
OSD Timeout
Exit
10
Enter
1.
Press the MENU key to bring up the OSD.
2.
Using the directional keys, select
to the feature you wish to adjust.
OSD from the on screen display. Then navigate
13
Adjusting the setting
Setting
Wide Mode
Full
DDC/CI
ON
ACM
OFF
Input
VGA
DP Format
DP1.2
Language
English
Reset
Exit
Enter
1.
Press the MENU key to bring up the OSD.
2.
Using the //
keys, select
feature you wish to adjust.
3.
The Setting menu can be used to adjust the screen Menu Language and other
important settings.
4.
DP mode selection, the default out of DP signal setting is DP1.2.
Setting from the OSD. Then navigate to the
User can follow the setting message to confirm selection of DP1.2 or DP1.1.
14
Product information
Information
3840x2160
H:135KHz V:60Hz
HDMI Input
S/N:ETL5309132635038083742
Exit
Enter
1.
Press the MENU key to bring up the OSD.
2.
Using the / keys, select
Information from the OSD. Then the basic information
of LCD monitor will show up for current input.
15
Troubleshooting
English
Before sending your LCD monitor for servicing, please check the troubleshooting list
below to see if you can self-diagnose the problem.
DVI(Dual Link)/ HDMI mode
Problem
No picture visible
LED status
Remedy
Blue
Using the OSD menu, adjust brightness and
contrast to maximum or reset to their default
settings.
Off
Check the power switch.
Check if the AC power cord is properly
connected to the monitor.
Amber
Check if the video signal cable is properly
connected at the back of monitor.
Check if the computer system is switched on
and in power saving/standby mode.
DP mode
Problem
No picture visible
LED status
Remedy
Blue
Using the OSD, adjust brightness and contrast
to maximum or reset to their default settings.
Off
Check the power switch.
Check if the AC power cord is properly
connected to the monitor.
Amber
Check if the video signal cable is properly
connected at the back of monitor.
Check that the computer system is switched
on and in power saving/ standby mode.
16
Download PDF