Acer | H257HU | Acer H257HU User Manual

Acer LCD Monitor
User Guide
Copyright © 2015. Acer Incorporated.
All Rights Reserved.
English
Acer LCD Monitor User Guide
Original Issue: 1/2015
Changes may be made periodically to the information in this publication without obligation to notify
any person of such revisions or changes. Such changes will be incorporated in new editions of this
manual or supplementary documents and publications. This company makes no representations or
warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims
the implied warranties of merchantability or fitness for a particular purpose.
Record the model number, serial number, purchase date and place of purchase information in the
space provided below. The serial number and model number are recorded on the label affixed to
your computer. All correspondence concerning your unit should include the serial number, model
number and purchase information.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any
form or by any means, electronically, mechanically, by photocopy, recording or otherwise, without
the prior written permission of Acer Incorporated.
Acer LCD Monitor User Guide
Model number: __________________________________
Serial number: ___________________________________
Date of purchase: ________________________________
Place of purchase: ________________________________
Acer and the Acer logo are registered trademarks of Acer Incorporated. Other companies’ product
names or trademarks are used herein for identification purposes only and belong to their respective
companies.
English
Information for your safety and
comfort
Safety instructions
Read these instructions carefully. Keep this document for future reference. Follow all
warnings and instructions marked on the product.
Special notes on LCD monitors
The following are normal with the LCD monitor and do not indicate a problem.
•
Due to the nature of the fluorescent light, the screen may flicker during initial
use. Turn off the power switch and then turn it on again to make sure the flicker
disappears.
•
You may find slightly uneven brightness on the screen depending on the desktop
pattern you use.
•
The LCD screen has 99.99% or more effective pixels. It may include blemishes of
0.01% or less such as a missing pixel or pixel lit all the time.
•
Due to the nature of the LCD screen, an afterimage of the previous screen may
remain after switching the image, when the same image is displayed for hours. In this
case, the screen is recovered slowly by changing the image or turning off the power
switch for a few hours.
Cleaning your monitor
Please carefully follow these guidelines when cleaning the monitor:
•
Always unplug the monitor before cleaning.
•
Use a soft cloth to wipe the screen and cabinet front and sides.
iii
Accessibility
English
Be sure that the power outlet you plug the power cord into is easily accessible and
located as close to the equipment operator as possible. When you need to disconnect
power from the equipment, be sure to unplug the power cord from the electrical outlet.
Safe listening
To protect your hearing, follow these instructions.
•
Gradually increase the volume until you can hear it clearly and comfortably and
without distortion.
•
After setting the volume level, do not increase it after your ears have adjusted.
•
Limit the amount of time listening to music at high volume.
•
Avoid turning up the volume to block out noisy surroundings.
•
Turn the volume down if you can’t hear people speaking near you.
Warnings
•
Do not use this product near water.
•
Do not place this product on an unstable cart, stand or table. If the product falls, it
could be seriously damaged.
•
Slots and openings are provided for ventilation to ensure reliable operation of the
product and to protect it from overheating. These openings must not be blocked
or covered. The openings should never be blocked by placing the product on a bed,
sofa, rug or other similar surface. This product should never be placed near or over
a radiator or heat register, or in a built-in installation unless proper ventilation is
provided.
•
Never push objects of any kind into this product through cabinet slots as they may
touch dangerous voltage points or short-out parts that could result in a fire or
electric shock. Never spill liquid of any kind onto or into the product.
•
To avoid damage of internal components and to prevent battery leakage, do not
place the product on a vibrating surface.
•
Never use it under sporting, exercising, or any vibrating environment which will
probably cause unexpected short current or damage internal devices.
•
The adapter is only used for this monitor, do not be used for other purposes.
•
Your device uses one of the following power supplies:
Manufacture: Shenzhen Honor Electronic.,Ltd:ADS-65AL-19-3 19065G(65W)
Using electrical power
•
•
iv
This product should be operated from the type of power indicated on the marking
label. If you are not sure of the type of power available, consult your dealer or local
power company.
Do not allow anything to rest on the power cord. Do not locate this product where
•
•
people will walk on the cord.
If an extension cord is used with this product, make sure that the total ampere rating
of the equipment plugged into the extension cord does not exceed the extension
cord ampere rating. Also, make sure that the total rating of all products plugged into
the wall outlet does not exceed the fuse rating.
Do not overload a power outlet, strip or receptacle by plugging in too many devices.
The overall system load must not exceed 80% of the branch circuit rating. If power
strips are used, the load should not exceed 80% of the power strip’s input rating.
This product’s power cord is equipped with a three-wire grounded plug. The
plug only fits in a grounded power outlet. Make sure the power outlet is properly
grounded before inserting the power cord plug. Do not insert the plug into a nongrounded power outlet. Contact your electrician for details.
Warning! The grounding pin is a safety feature. Using a power
outlet that is not properly grounded may result in electric
shock and/or injury.
Note: The grounding pin also provides good protection from
unexpected noise produced by other nearby electrical devices that
may interfere with the performance of this product.
•
Use the product only with the supplied power supply cord set. If you need to
replace the power cord set, make sure that the new power cord meets the following
requirements: detachable type, UL listed/CSA certified, type SPT-2, rated 7 A 125 V
minimum, VDE approved or its equivalent, 4.6 meters (15 feet) maximum length.
Product servicing
Do not attempt to service this product yourself, as opening or removing covers may
expose you to dangerous voltage points or other risks. Refer all servicing to qualified
service personnel.
Unplug this product from the wall outlet and refer servicing to qualified service
personnel when:
•
the power cord or plug is damaged, cut or frayed
•
liquid was spilled into the product
•
the product was exposed to rain or water
•
the product has been dropped or the case has been damaged
•
the product exhibits a distinct change in performance, indicating a need for service
•
the product does not operate normally after following the operating instructions
v
English
•
English
Note: Adjust only those controls that are covered by the operating
instructions, since improper adjustment of other controls may result in damage
and will often require extensive work by a qualified technician to restore the
product to normal condition.
Potentially explosive environments
Switch off your device in any area with a potentially explosive atmosphere and obey all
signs and instructions. Potentially explosive atmospheres include areas where you would
normally be advised to turn off your vehicle engine. Sparks in such areas could cause
an explosion or fire resulting in bodily injury or even death. Switch off the device near
gas pumps at service stations. Observe restrictions on the use of radio equipment in fuel
depots, storage and distribution areas; chemical plants; or where blasting operations are
in progress. Areas with a potentially explosive atmosphere are often, but not always,
marked. They include below deck on boats, chemical transfer or storage facilities,
vehicles using liquefied petroleum gas (such as propane or butane), and areas where the
air contains chemicals or particles such as grain, dust or metal powders.
Additional safety information
Your device and its enhancements may contain small parts. Keep them out of the reach
of small children.
IT Equipment Recycling Information
Acer is strongly committed to environmental protection and views recycling, in the form
of salvaging and disposal of used equipment, as one of the company’s top priorities in
minimizing the burden placed on the environment.
We at Acer are very conscious of the environmental effects of our business and strive to
identify and provide the best working procedures to reduce the environmental impact
of our products.
For more information and help when recycling, please go to this website:
http://www.acer-group.com/public/Sustainability/sustainability01.htm
Visit www.acer-group.com for further information on the features and benefits of our
other products.
Disposal instructions
Do not throw this electronic device into the trash when discarding. To minimize
pollutionandensureutmostprotectionoftheglobalenvironment,pleaserecycle.
For more information on the Waste from Electrical and Electronics Equipment
(WEEE) regulations, visit http://www.acer-group.com/public/Sustainability/
sustainability01.htm
vi
LCD pixel statement
English
The LCD unit is produced with high-precision manufacturing techniques. Nevertheless,
some pixels may occasionally misfire or appear as black or red dots. This has no effect on
the recorded image and does not constitute a malfunction.
This product has been shipped enabled for power management:
•
Activate display’s Sleep mode within 15 minutes of user inactivity.
•
Activate computer’s Sleep mode within 30 minutes of user inactivity.
•
Wake the computer from Sleep mode by pushing the power button.
Tips and information for comfortable use
Computer users may complain of eyestrain and headaches after prolonged use. Users are
also at risk of physical injury after long hours of working in front of a computer. Long
work periods, bad posture, poor work habits, stress, inadequate working conditions,
personal health and other factors greatly increase the risk of physical injury.
Incorrect computer usage may lead to carpal tunnel syndrome, tendonitis, tenosynovitis
or other musculoskeletal disorders. The following symptoms may appear in the hands,
wrists, arms, shoulders, neck or back:
•
numbness, or a burning or tingling sensation
•
aching, soreness or tenderness
•
pain, swelling or throbbing
•
stiffness or tightness
•
coldness or weakness
If you have these symptoms, or any other recurring or persistent discomfort and/or pain
related to computer use, consult a physician immediately and inform your company’s
health and safety department.
The following section provides tips for more comfortable computer use.
Finding your comfort zone
Find your comfort zone by adjusting the viewing angle of the monitor, using a footrest,
or raising your sitting height to achieve maximum comfort. Observe the following tips:
•
refrain from staying too long in one fixed posture
•
avoid slouching forward and/or leaning backward
vii
•
stand up and walk around regularly to remove the strain on your leg muscles
Taking care of your vision
English
Long viewing hours, wearing incorrect glasses or contact lenses, glare, excessive room lighting,
poorly focused screens, very small typefaces and low-contrast displays could stress your eyes. The
following sections provide suggestions on how to reduce eyestrain.
Eyes
•
Rest your eyes frequently.
• Give your eyes regular breaks by looking away from the monitor and focusing on a istant point.
•
Blink frequently to keep your eyes from drying out.
Display
•
Keep your display clean.
•
Keep your head at a higher level than the top edge of the display so your eyes point
downward when looking at the middle of the display.
•
Adjust the display brightness and/or contrast to a comfortable level for enhanced
text readability and graphics clarity.
•
Eliminate glare and reflections by:
•
placing your display in such a way that the side faces the window or any light
source
•
minimizing room light by using drapes, shades or blinds
•
using a task light
•
changing the display’s viewing angle
•
using a glare-reduction filter
•
using a display visor, such as a piece of cardboard extended from the display’s top
front edge
•
Avoid adjusting your display to an awkward viewing angle.
•
Avoid looking at bright light sources, such as open windows, for extended periods of
time.
Developing good work habits
Develop the following work habits to make your computer use more relaxing and
productive:
viii
•
Take short breaks regularly and often.
•
Perform some stretching exercises.
•
Breathe fresh air as often as possible.
•
Exercise regularly and maintain a healthy body.
English
Declaration of Conformity
We,
Acer Incorporated
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi, New Taipei City 221, Taiwan
Contact Person: Mr. RU Jan, e-mail:ru.jan@acer.com
And,
Acer Italy s.r.l
Via Lepetit, 40, 20020 Lainate (MI) Italy
Tel: +39-02-939-921 ,Fax: +39-02 9399-2913
www.acer.it






Declare under our own responsibility that the product:
Product:
LCD Monitor
Trade Name:
Acer
Model Number:
H257HU
SKU Number:
H257HU xxxxxx;
(“x” = 0~9, a ~ z, A ~ Z, or blank)
To which this declaration refers conforms to the relevant standard or other standardizing documents:
EN55022:2010 Class B; EN55024:2010
EN 61000-3-2:2006+A1:2009+A2:2009, Class D
EN61000-3-3:2008
EN60950-1:2006/A11:2009/A1:2010+A12:2011
Regulation (EC) No. 1275/ 2008; EN 50564:2011; IEC 62301:2011
EN50581:2012
We hereby declare above product is in compliance with the essential requirements and other relevant
provisions of EMC Directive 2004/108/EC, Low Voltage Directive 2006/95/EC, and RoHS Directive
2011/65/EU and Directive 2009/125/EC with regard to establishing a framework for the setting of ecodesign
requirements for energy-related product.
Year to begin affixing CE marking 2015.
_______________________________
RU Jan / Sr. Manager
Regulation, Acer Inc.
Jan. 05, 2015
Date
ix
Acer America Corporation
English
333 West San Carlos St., San Jose
Suite 1500
CA 95110, U. S. A.
Tel : 254-298-4000
Fax : 254-298-4147
www.acer.com
Federal Communications Commission
Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
The following local Manufacturer /Importer is responsible for this declaration:
x
Product:
LCD Monitor
Model Number:
H257HU
SKU Number:
H257HU xxxxxx
(“x” = 0~9, a ~ z, or A ~ Z)
Name of Responsible Party:
Acer America Corporation
Address of Responsible Party:
333 West San Carlos St.
Suite 1500
San Jose, CA 95110
U. S. A.
Contact Person:
Acer Representative
Phone No.:
254-298-4000
Fax No.:
254-298-4147
Unpacking1
Attaching the base (for selected models) Screen position adjustment
Connecting the adapter and AC Power cord Power saving
Display Data Channel (DDC)
Connector pin assignment
24-pin color display signal cable
19-pin color display signal cable
20-pin color display signal cable
2
3
3
3
4
4
4
5
5
Standard timing table
6
Installation7
Users controls
8
Panel controls
Using the Shortcut Menu
9
Acer eColor Management
Operation instructions
Features and benefits
Using the OSD Menus Picture Menu
OSD Menu
8
10
10
10
11
11
12
English
iii
Safety instructions
iii
Special notes on LCD monitors
iii
Cleaning your monitor
iii
Accessibilityiv
Safe listening
iv
Warningsiv
Using electrical power
iv
Product servicing
v
Potentially explosive environments
vi
Additional safety information
vi
IT Equipment Recycling Information
vi
Disposal instructions
vi
LCD pixel statement
vii
Tips and information for comfortable use
vii
Finding your comfort zone
vii
Taking care of your vision
viii
Developing good work habits
viii
Declaration of Conformity
ix
Federal Communications Commission Declaration of
Conformityx
Contents
Information for your safety and comfort
Setting Menu
Information Menu
13
14
English
Troubleshooting15
DVI/HDMI/DP Mode (Optional)
15
Unpacking
Please check that the following items are present when you unpack the box, and save
LCD monitor
Quick start guide
DP Cable
(Optional)
HDMI cable
(Optional)
DVI cable
(Optional)
AC Adapter
English
the packing materials in case you need to ship or transport the monitor in the future.
Audio cable
(Optional)
AC Power cord
1
Attaching the base (for selected models)
English
Note: Remove the monitor and monitor base from its packaging.
Carefully place the monitor face-down on a stable surface -- use a
cloth to avoid scratching the screen.
1
Attach the monitor stand arm to the base.
2
Ensure that the base is locked onto the monitor stand arm.
• Secure the base to the monitor stand arm by turning the white screw using the
integrated tab or a suitable coin. (for selected models)
Note: Take care when performing the installation to avoid injuring
yourself.
2
Screen position adjustment
English
To optimize the viewing position, you can adjust the
monitor tilt, using both of your hands to hold the edges
of the monitor. The monitor can be adjusted to 15
degrees up or 5 degrees down.
Connecting the adapter and AC Power cord
• Check first to make sure that the power cord you use is the correct type required for
your area.
• The monitor has a universal power supply that allows operation in either 100/120 V
AC or 220/240 V AC voltage area. No user-adjustment is required.
• Plug one end of the AC power cord to the Adapter, and plug the other end into an
AC outlet.
• For units using 120 V AC:
Use a UL-listed cord set, type SVT wire and plug rated 10 A/125 V.
• For units using 220/240 V AC:
Use a cord set consisting of H05VV-F cord and plug rated 10 A/250 V. The cord set
should have the appropriate safety approvals for the country in which the equipment
will be installed.
Power saving
The monitor will be switched to “power saving” mode by the control signal from the
display controller, as indicated by the blinking blue light.
Mode
LED light
On
Blue
Standby/Power saving
Blinking Blue
The power saving mode will be kept until a
control signal has been detected or the keyboard
or mouse is activated. The recovery time from
“power saving” mode back to “on” is around 3
seconds.
LED indicator
3
Display Data Channel (DDC)
English
To make installation easier, so long as your system supports the DDC protocol, the
monitor is able to plug-and-play. The DDC is a communication protocol through which
the monitor automatically informs the host system about its capabilities; for example,
supported resolutions and corresponding timing. The monitor supports the DDC2B
standard.
24-pin color display signal cable
4
PIN No.
Description
PIN No.
Description
1
TMDS data 2-
13
TMDS data 3+
2
TMDS data 2+
14
+5 V power
3
TMDS data 2/4 shield
15
DVI detect
4
TMDS data 4-
16
Hot-plug detection
5
TMDS data 4+
17
TMDS data 0-
6
DDC clock
18
TMDS data 0+
7
DDC data
19
TMDS data 0/5 shield
8
NC
20
TMDS data 5-
9
TMDS data 1-
21
TMDS data 5+
10
TMDS data 1+
22
TMDS clock shield
11
TMDS data 1/3 shield
23
TMDS clock+
12
TMDS data 3-
24
DDC TMDS clock-
19-pin color display signal cable
19 1715 13 11 9 7 5 3 1
English
18 16 1412 10 8 6 4 2
PIN No.
Description
PIN No.
Description
1
TMDS Data2+
2
TMDS Data2 Shield
3
TMDS Data2-
4
TMDS Data1+
5
TMDS Data1 Shield
6
TMDS Data1-
7
TMDS Data0+
8
TMDS Data0 Shield
9
TMDS Data0-
10
TMDS Clock+
11
TMDS Clock Shield
12
TMDS Clock-
13
CEC
14
Reserved (N.C. on device)
15
SCL
16
SDA
17
DDC/CEC Ground
18
+5V Power
19
Hot Plug Detect
20-pin color display signal cable
PIN No.
Description
PIN No.
Description
1
ML_Lane 0+
2
GND
3
ML_Lane 0-
4
ML_Lane 1+
5
GND
6
ML_Lane 1-
7
ML_Lane 2+
8
GND
9
ML_Lane 2-
10
ML_Lane 3+
11
GND
12
ML_Lane 3-
13
CONFIG1
14
CONFIG2
15
AUX CH+
16
GND
17
AUX CH-
18
Hot Plug
19
Return
20
DP_PWR
5
English
Standard timing table
Mode
Resolution
(active dot)
640x480@60Hz
800 x 525
31.469
59.940
25.175
VGA
640x480@72Hz
832 x 520
37.861
72.809
31.500
640x480@75Hz
840 x 500
37.500
75.000
31.500
MAC
640x480@66.66Hz
864x525
35.000
66.667
30.240
VESA
720x400@70Hz
900x449
31.469
70.087
28.322
SVGA
MAC
XGA
MAC
VESA
SXGA
6
Resolution
Horizontal
Vertical
Nominal Pixel
(total dot) Frequency (KHz) Frequency (Hz) Clock (MHz)
800x600@56Hz
1024 x 625
35.156
56.250
36.000
800x600@60Hz
1056 x 628
37.879
60.317
40.000
800x600@72Hz
1040 x 666
48.077
72.188
50.000
800x600@75Hz
1056x625
46.875
75.000
49.500
832x624@74.55Hz
1152x667
49.722
74.550
57.280
1024x768@60Hz
1344x806
48.363
60.004
65.000
1024x768@70Hz
1328x806
56.476
70.069
75.000
1024x768@75Hz
1312x800
60.023
75.029
78.750
1152x870@75Hz
1456x915
68.681
75.062
100.000
1152x864@75Hz
1600x900
67.500
75.000
108.000
1280x960@60Hz
1800x1000
60.000
60.000
108.000
1280x1024@60Hz 1688x1066
63.981
60.020
108.000
1280x1024@75Hz 1688x1066
79.976
75.025
135.000
74.250
VESA
1280x720@60Hz
1650x750
45.000
60.000
WXGA
1280x800@60Hz
1680x831
49.702
59.810
83.500
WXGA+
1440x900@60Hz
1904x934
55.935
59.887
106.500
WSXGA+
1680x1050@60Hz
2240*1089
65.290
59.954
146.250
FHD
1920x1080@60Hz
2200x1125
67.500
60.000
148.500
QHD
2560x1440@60Hz
2720x1481
88.787
59.951
241.500
Installation
To install the monitor on your host system, please follow the steps below:
Steps
Connect the video cable
English
1
a Make sure both the monitor and computer are switched off.
b Connect the digital cable
(1) Make sure both the monitor and computer are switched off.
(2) DVI Cable (Optional, only Dual-Input Model)
a. Make sure both the monitor and computer are powered-OFF.
b. Connect the DVI cable to the computer.
(3) HDMI Cable (Optional, only HDMI-Input Model)
a. Make sure both the monitor and computer are powered-OFF.
b. Connect the HDMI cable to the computer.
(4) DP Cable (Optional, only DP-Input Model)
a. Make sure both the monitor and computer are powered-OFF.
b. Connect the DP cable to the computer.
c Connect the audio cable (Optional, only Audio-input Model).
2
Connect the adapter
a Connect the AC cord to the adapter.
b Connect one end of the adapter to the monitor and the other end to a properly
grounded, AC outlet.
3
Turn on the monitor and computer
Turn on the monitor first, then the computer. This sequence is very important.
4
If the monitor does not function properly, please refer to the troubleshooting section
to diagnose the problem.
HDMI
HDMI
DVI
HDMI
DP
AUDIO IN
HDMI
DVI
DP
DC IN
Note: Audio output is only for audio output model.
In order to prevent damage to the monitor, do not lift the monitor by its base.
7
English
Users controls
54 3 2 1
Panel controls
8
No.
Item
Description
1
Power button/
indicator
Turn the monitor on/off.
Blue indicates power on. Blinking blue indicates standby/
power saving mode.
2
< / > button
Press the < / > button to navigate to the desired function,
and press the Menu button to select the function. Press the
< / > button to change the settings of the current function.
3
Menu/Enter
button
Press to view the OSD menu. Press it again to enter a
selection in the OSD menu.
4
Auto/Exit button
•
5
Empowering Key
Press this button to open the Acer eColor Management OSD
and access the scenario modes.
When the OSD menu is active, press this button to exit
the OSD menu.
• When the OSD menu is inactive, press this button for two seconds
to activate the Auto Adjustment function and the monitor will
automatically optimize the display position, focus, and clock of
your display. (For VGA mode only)
AUTO
English
Using the Shortcut Menu
Input
Press any of the function buttons (Empowering Key, Auto button, or Menu button) to
open the shortcut menu. The shortcut menu lets you quickly select the most commonly
accessed settings.
Icon
AUTO
Input
Item
Description
Empowering
Press the Empowering Key to open the Acer eColor
Management and access the scenario modes.
Auto
Press the Auto button to activate the Auto Adjustment
function and the monitor will automatically optimize the
display position, focus, and clock of your display. (For VGA
mode only)
Menu
Press the Menu button to activate the OSD menu.
Volume
Press the Volume button to adjust volume. (Optional, only
Audio-Input Model)
Input
Press the Input button to select from different video
sources that may be connected to your monitor. (Optional,
only Dual-Input Model or HDMI-Input Model)
9
Acer eColor Management
Operation instructions
English
1 Press the Empowering Key to open the Acer eColor Management OSD menu and
access the scenario modes.
mpowering Technology
User
ECO
Standard Graphics
Movie
2 Press the < / > button to select the desired mode.
3 Press the Auto button to confirm the selection and exit Acer eColor Management.
Features and benefits
Icon
10
Mode type
Description
User mode
User-defined. Settings can be fine-tuned to suit any
situation.
ECO mode
Adjusts the settings to reduce power consumption.
Standard mode
Default settings. Reflects native display capability.
Graphic mode
Enhances colors and emphasizes fine detail. Pictures and
photographs appear in vibrant colors with sharp detail.
Movie mode
Displays scenes in clearest detail. Presents great visuals,
even in unsuitably-lit environments.
Using the OSD Menus
English
Note: The following content is for general reference only. Actual
product specifications may vary.
Your LCD monitor is equipped with an on-screen display (OSD) menu for making various
adjustments and settings.
Press the Menu button to open the OSD menu. You can use the OSD menu to adjust the picture
quality, OSD timeout, and general settings.
Picture Menu
The Picture menu is used for adjusting the picture quality.
Picture
Picture
Acer eColor Management
Blue Light
Brightness
70
Contrast
Colour Temp
6-axis Hue
Off
50
Blue Light
Gamma
2.2
sRGB mode
Off
6-axis Saturate
1 Press the Menu button to bring up the OSD menu.
2 Press the < / > button to select
Picture menu.
Picture and press the Menu button to enter the
The following options are available in the Picture menu: Acer ecolor Management,
Blue Light, Brightness, Contrast, 6-axis Saturate, 6-axis Hue, sRGB mode, Super
sharpness, and Colour Temp.
3 Press the < / > button to scroll through the Picture options, and press the Menu
button to enter its sub-menu.
4 Press the < / > button to adjust/select the setting and press the Auto button to
confirm.
11
OSD Menu
English
The OSD menu is used for adjusting the OSD menu location and the timeout setting.
OSD
OSD Timeout
10
1 Press the Menu button to bring up the OSD menu.
2 Press the < / > button to select
OSD and press the Menu button to enter the
OSD menu.
3 To adjust the OSD H.Position / V.Position, press the Menu button to enter its submenu.
4 Press the < / > button to to adjust the target position and press the Auto button to
confirm.
12
Setting Menu
English
The Setting menu is used for adjusting the general settings for current input signal such
as aspect ratio, OSD language, and etc.
Setting
Wide Mode
DDC/CI
OD
Full
ON
Normal
ACM
OFF
Input
HDMI
DTS
Language
OFF
English
Reset
1 Press the Menu button to bring up the OSD menu.
2 Press the < / > button to select
Setting and press the Menu button to enter the
Setting menu.
The following options are available in the Setting menu: Wide Mode, DDC/CI, OD,
ACM, Input, Language, and Reset.
3 Press the < / > button to scroll through the Setting options, and press the Menu
button to enter its sub-menu.
4 Press the < / > button to adjust/select the setting and press the Auto button to
confirm.
13
Information Menu
English
The Information menu displays the basic information of the LCD monitor.
Information
2560x1440
H:68KHz V:60Hz
HDMI Input
S/N:ETRLA00803104000502400
1 Press the Menu button to bring up the OSD menu.
2 To view the basic information of the LCD monitor, press the < / > button to select
Information.
14
Troubleshooting
English
Before sending your LCD monitor for servicing, please check the troubleshooting list
below to see if you can self-diagnose the problem.
DVI/HDMI/DP Mode (Optional)
Problem
No picture visible
LED status
Remedy
Blue
Using the OSD menu, adjust brightness and
contrast to maximum or reset to their default
settings.
Off
Check the power switch.
Check if the AC power cord is properly
connected to the monitor.
Blinking Blue
Check if the video signal cable is properly
connected at the back of monitor.
Check if the computer system is switched on
and in power saving/standby mode.
For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited.
DTS, the Symbol, & DTS and the Symbol together are registered trademarks, and DTS Sound is a
trademark of DTS, Inc. © DTS, Inc. All Rights Reserved.
15
Download PDF