Acer | Q226HQL | Acer Q226HQL User Manual

Acer LCD Monitor
User Guide
Copyright © 2012. Acer Incorporated.
All Rights Reserved.
Acer LCD Monitor User Guide
Original Issue: 09/2012
Changes may be made periodically to the information in this publication without obligation
to notify any person of such revisions or changes. Such changes will be incorporated in new
editions of this manual or supplementary documents and publications. This company makes
no representations or warranties, either expressed or implied, with respect to the contents
hereof and specifically disclaims the implied warranties of merchantability or fitness for a
particular purpose.
Record the model number, serial number, purchase date and place of purchase information in
the space provided below. The serial number and model number are recorded on the label
affixed to your computer. All correspondence concerning your unit should include the serial
number, model number and purchase information.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronically, mechanically, by photocopy, recording or otherwise,
without the prior written permission of Acer Incorporated.
Acer LCD Monitor User Guide
Model number: __________________________________
Serial number: ___________________________________
Date of purchase: ________________________________
Place of purchase: ________________________________
Acer and the Acer logo are registered trademarks of Acer Incorporated. Other companies'
product names or trademarks are used herein for identification purposes only and belong to
their respective companies.
iii
Information for your safety and
comfort
Safety instructions
Read these instructions carefully. Keep this document for future reference.
Follow all warnings and instructions marked on the product.
Special notes on LCD monitors
The following are normal with the LCD monitor and do not indicate a problem.
•
Due to the nature of the fluorescent light, the screen may flicker during
initial use. Turn off the power switch and then turn it on again to make
sure the flicker disappears.
•
You may find slightly uneven brightness on the screen depending on the
desktop pattern you use.
•
The LCD screen has 99.99% or more effective pixels. It may include
blemishes of 0.01% or less such as a missing pixel or a pixel lit all the time.
•
Due to the nature of the LCD screen, an afterimage of the previous screen
may remain after switching the image, when the same image is displayed
for hours. In this case, the screen is recovered slowly by changing the image
or turning off the power switch for a few hours.
Cleaning your monitor
Please carefully follow these guidelines when cleaning the monitor:
•
Always unplug the monitor before cleaning.
•
Use a soft cloth to wipe the screen and cabinet front and sides.
iv
Accessibility
Be sure that the power outlet you plug the power cord into is easily accessible
and located as close to the equipment operator as possible. When you need to
disconnect power from the equipment, be sure to unplug the power cord from
the electrical outlet.
Safe listening
To protect your hearing, follow these instructions.
•
Gradually increase the volume until you can hear it clearly and comfortably
and without distortion.
•
After setting the volume level, do not increase it after your ears have
adjusted.
•
Limit the amount of time listening to music at high volume.
•
Avoid turning up the volume to block out noisy surroundings.
•
Turn the volume down if you can't hear people speaking near you.
Warnings
•
•
•
•
•
•
•
•
Do not use this product near water.
Do not place this product on an unstable cart, stand or table. If the product
falls, it could be seriously damaged.
Slots and openings are provided for ventilation to ensure reliable
operation of the product and to protect it from overheating. These
openings must not be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug or other similar surface.
This product should never be placed near or over a radiator or heat
register, or in a built-in installation unless proper ventilation is provided.
Never push objects of any kind into this product through cabinet slots as
they may touch dangerous voltage points or short-out parts that could
result in a fire or electric shock. Never spill liquid of any kind onto or into
the product.
To avoid damage of internal components and to prevent battery leakage,
do not place the product on a vibrating surface.
Never use it under sporting, exercising, or any vibrating environment
which will probably cause unexpected short current or damage internal
devices.
The adapter is only used for this monitor ,do not be used for other purposes.
Your device uses one of the following power supplies:
Manufacturer: Delta Electronics Inc., Model: ADP-40PH BB(Q226HQL/Q236HL)
Manufacturer: T PV Electronics ( Fu jian) CO., LTD , Model: ADPC1940 (Q226HQL/Q236HL)
.
(Q226HQL/Q236HL)
Manufacturer: T PV Electronics ( Fu jian) CO., LTD , Model: ADPC1965 (Q276HL)
.
ADS-65 LSI-19-1 19065G
(Q276HL)
Using electrical power
•
•
•
This product should be operated from the type of power indicated on the
marking label. If you are not sure of the type of power available, consult
your dealer or local power company.
Do not allow anything to rest on the power cord. Do not locate this
product where people will walk on the cord.
If an extension cord is used with this product, make sure that the total
v
•
•
ampere rating of the equipment plugged into the extension cord does not
exceed the extension cord ampere rating. Also, make sure that the total
rating of all products plugged into the wall outlet does not exceed the fuse
rating.
Do not overload a power outlet, strip or receptacle by plugging in too
many devices. The overall system load must not exceed 80% of the branch
circuit rating. If power strips are used, the load should not exceed 80% of
the power strip's input rating.
This product's power cord is equipped with a three-wire grounded plug.
The plug only fits in a grounded power outlet. Make sure the power outlet
is properly grounded before inserting the power cord plug. Do not insert
the plug into a non-grounded power outlet. Contact your electrician for
details.
Warning! The grounding pin is a safety feature. Using a power
outlet that is not properly grounded may result in electric shock
and/or injury.
Note: The grounding pin also provides good protection from
unexpected noise produced by other nearby electrical devices that
may interfere with the performance of this product.
•
Use the product only with the supplied power supply cord set. If you need
to replace the power cord set, make sure that the new power cord meets
the following requirements: detachable type, UL listed/CSA certified, type
SPT-2, rated 7 A 125 V minimum, VDE approved or its equivalent, 4.6
meters (15 feet) maximum length.
Product servicing
Do not attempt to service this product yourself, as opening or removing covers
may expose you to dangerous voltage points or other risks. Refer all servicing to
qualified service personnel.
Unplug this product from the wall outlet and refer servicing to qualified service
personnel when:
•
the power cord or plug is damaged, cut or frayed
•
•
•
•
•
liquid was spilled into the product
the product was exposed to rain or water
the product has been dropped or the case has been damaged
the product exhibits a distinct change in performance, indicating a need
for service
the product does not operate normally after following the operating
instructions
vi
Note: Adjust only those controls that are covered by the operating
instructions, since improper adjustment of other controls may
result in damage and will often require extensive work by a
qualified technician to restore the product to normal condition.
Potentially explosive environments
Switch off your device in any area with a potentially explosive atmosphere and
obey all signs and instructions. Potentially explosive atmospheres include areas
where you would normally be advised to turn off your vehicle engine. Sparks in
such areas could cause an explosion or fire resulting in bodily injury or even
death. Switch off the device near gas pumps at service stations. Observe
restrictions on the use of radio equipment in fuel depots, storage and
distribution areas; chemical plants; or where blasting operations are in progress.
Areas with a potentially explosive atmosphere are often, but not always,
marked. They include below deck on boats, chemical transfer or storage
facilities, vehicles using liquefied petroleum gas (such as propane or butane),
and areas where the air contains chemicals or particles such as grain, dust or
metal powders.
Additional safety information
Your device and its enhancements may contain small parts. Keep them out of
the reach of small children.
IT Equipment Recycling Information
Acer is strongly committed to environmental protection and views recycling, in
the form of salvaging and disposal of used equipment, as one of the company's
top priorities in minimizing the burden placed on the environment.
We at Acer are very conscious of the environmental effects of our business and
strive to identify and provide the best working procedures to reduce the
environmental impact of our products.
For more information and help when recycling, please go to this website:
http://www.acer-group.com/public/Sustainability/sustainability01.htm
Visit www.acer-group.com for further information on the features and benefits
of our other products.
"For use in Office environments with special controlled illumination to avoid disturbing reflections from the screen' "For indoor use only and gaming purposes
illumination
in environments with special controlled
to avoid disturbing
reflections
from the screen '
Disposal instructions
Do not throw this electronic device into the trash when discarding.
To minimize pollution and ensure utmost protection of the global
environment, please recycle. For more information on the Waste
from Electrical and Electronics Equipment (WEEE) regulations, visit
http://www.acer-group.com/public/Sustainability/sustainability01.htm
vii
LCD pixel statement
The LCD unit is produced with high-precision manufacturing techniques.
Nevertheless, some pixels may occasionally misfire or appear as black or
red dots. This has no effect on the recorded image and does not constitute
a malfunction.
This product has been shipped enabled for power management:
•
•
•
Activate display’s Sleep mode within 15 minutes of user inactivity.
Activate computer’s Sleep mode within 30 minutes of user inactivity.
Wake the computer from Sleep mode by pushing the power button.
Tips and information for comfortable use
Computer users may complain of eyestrain and headaches after prolonged use.
Users are also at risk of physical injury after long hours of working in front of a
computer. Long work periods, bad posture, poor work habits, stress,
inadequate working conditions, personal health and other factors greatly
increase the risk of physical injury.
Incorrect computer usage may lead to carpal tunnel syndrome, tendonitis,
tenosynovitis or other musculoskeletal disorders. The following symptoms may
appear in the hands, wrists, arms, shoulders, neck or back:
•
•
•
•
•
numbness, or a burning or tingling sensation
aching, soreness or tenderness
pain, swelling or throbbing
stiffness or tightness
coldness or weakness
If you have these symptoms, or any other recurring or persistent discomfort
and/or pain related to computer use, consult a physician immediately and
inform your company's health and safety department.
The following section provides tips for more comfortable computer use.
Finding your comfort zone
Find your comfort zone by adjusting the viewing angle of the monitor, using a
footrest, or raising your sitting height to achieve maximum comfort. Observe
the following tips:
•
•
•
refrain from staying too long in one fixed posture
avoid slouching forward and/or leaning backward
stand up and walk around regularly to remove the strain on your leg
muscles
viii
Taking care of your vision
Long viewing hours, wearing incorrect glasses or contact lenses, glare, excessive
room lighting, poorly focused screens, very small typefaces and low-contrast
displays could stress your eyes. The following sections provide suggestions on
how to reduce eyestrain.
Eyes
•
•
•
Rest your eyes frequently.
Give your eyes regular breaks by looking away from the monitor and
focusing on a distant point.
Blink frequently to keep your eyes from drying out.
Display
•
Keep your display clean.
•
•
•
•
•
Keep your head at a higher level than the top edge of the display so your
eyes point downward when looking at the middle of the display.
Adjust the display brightness and/or contrast to a comfortable level for
enhanced text readability and graphics clarity.
Eliminate glare and reflections by:
•
placing your display in such a way that the side faces the window or
any light source
•
•
•
minimizing room light by using drapes, shades or blinds
•
•
using a glare-reduction filter
using a task light
changing the display's viewing angle
using a display visor, such as a piece of cardboard extended from the
display's top front edge
Avoid adjusting your display to an awkward viewing angle.
Avoid looking at bright light sources, such as open windows, for extended
periods of time.
Developing good work habits
Develop the following work habits to make your computer use more relaxing
and productive:
•
Take short breaks regularly and often.
•
•
•
Perform some stretching exercises.
Breathe fresh air as often as possible.
Exercise regularly and maintain a healthy body.
TABLE OF CONTENTS
UNPACKING............................................................................................ 1
ATTACHING / REMOVING THE BASE..................................................... 2
SCREEN POSITION ADJUSTMENT .......................................................... 2
CONNECTING THE POWER CORD.......................................................... 3
SAFETY PRECAUTION............................................................................. 3
CLEANING YOUR MONITOR .................................................................. 3
POWER SAVING...................................................................................... 4
DDC......................................................................................................... 4
CONNECTOR PIN ASSIGNMENT............................................................. 5
STANDARD TIMING TABLE .................................................................... 7
INSTALLATION........................................................................................ 8
USER CONTROLS ................................................................................... 10
TROUBLESHOOTING ............................................................................ 16
UNPACKING
Please check the following items are present when you unpack the box, and
save the packing materials in case you will need to ship or transport the
monitor in future.
z
z
AC Power Cord
Audio Cable
(Optional)
z
z
z
LCD Monitor
D-Sub Cable
(Optional)
MHL cable
(Optional)
MHL
z
AC Adapter
z
Quick Start Guide
Q226HQL/Q236HL/Q276HL
EN-1
z
z
DVI Cable (Optional)
HDMI cable
(Optional)
ATTACHING / REMOVING THE BASE
Note: Remove the monitor and monitor base from its packaging.
Carefully place the monitor face-down on a stable surface -- use a
cloth to avoid scratching the screen.
1.
2.
Attach the monitor stand arm to the Ensure that the base is locked onto the
base.
monitor stand arm.
SCREEN POSITION ADJUSTMENT
In order to optimize the best viewing position, you can adjust the tilt of the
monitor by using both of your hands to hold the edges of the monitor as
shown in the figure below.
The monitor can be adjusted to 15 degrees up or 5 degrees down as indicated
by arrow below.
EN-2
CONNECTING THE POWER CORD
z
z
z
z
z
Check first to make sure that the power cord you use is the correct type
required for your area.
This monitor has a universal power supply that allows operation in either
100/120V AC or 220/240 V AC voltage area. No user-adjustment is required.
Plug one end of the AC power cord to the adapter, and plug the other end
into an AC outlet.
For unit using at 120 V AC:
Use a UL Listed Cord Set, Type SVT wire and plug rated 10 A/125 V.
For unit using at 220/240 V AC (outside of U.S.):
Use a Cord Set consisting of H05VV-F cord and plug rated 10 A, 250 V. The
cord set should have the appropriate safety approvals for the country in
which the equipment will be installed.
SAFETY PRECAUTION
z
z
z
z
z
z
Avoid placing the monitor, or any other heavy object, on the power cord
to avoid damage to the cable.
Do not expose the monitor to rain, excessive moisture, or dust.
Do not cover the ventilation slots or openings of the monitor. Always put
the monitor in a place where there is adequate ventilation.
Avoid placing the monitor against a bright background or where sun-light
or other light sources may reflect on the face of the monitor. Place the
monitor just below eye level.
Handle with care when transporting the monitor.
Refrain from giving shock or scratch to the screen, as screen is fragile.
CLEANING YOUR MONITOR
Please carefully follow the below guidelines when cleaning the monitor.
z Always unplug the monitor before cleaning.
z Use a soft cloth to wipe the screen and cabinet front and sides.
EN-3
POWER SAVING
The monitor will be driven into Power Saving” mode by the control signal
from the display controller, as indicated by the amber-color power LED.
State
LED Light
ON
Blue
Power Saving Mode
Amber
The power saving states will be kept until a control signal has been detected
or the keyboard or mouse is activated. The recovery time from Active OFF
state back to ON state is around 3 seconds.
DDC
To make your installation easier, the monitor is able to Plug and Play with
your system if your system also supports DDC protocol. The DDC (Display Data
Channel) is a communication protocol through which the monitor
automatically informs the host system about its capabilities, for example,
supported resolutions and corresponding timing. The monitor supports
DDC2B standard.
EN-4
CONNECTOR PIN ASSIGNMENT
15-Pin Color Display Signal Cable
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1.
Red
9.
+5V
2.
Green
10.
Logic Ground
3.
Blue
11.
Monitor Ground
4.
Monitor Ground
12.
DDC-Serial Data
5.
DDC-return
13.
H-Sync
6.
R-Ground
14.
V-Sync
7.
G-Ground
15.
DDC-Serial Clock
8.
B-Ground
24-Pin Color Display Signal Cable*
PIN
Meaning
PIN
Meaning
1.
TMDS Data2-
13.
NC
2.
TMDS Data2+
14.
+5V Power
3.
TMDS Data 2/4 Shield
15.
Logic Ground
4.
NC
16.
Hot Plug Detect
5.
NC
17.
TMDS Data0-
6.
DDC Clock
18.
TMDS Data0+
7.
DDC Data
19.
TMDS Data 0/5 Shield
8.
NC
20.
NC
9.
TMDS Data1-
21.
NC
10.
TMDS Data1+
22.
TMDS Clock Shield
11.
TMDS Data 1/3 Shield
23.
TMDS Clock+
12.
NC
24.
DDC TMDS Clock-
EN-5
19-Pin Color Display Signal Cable*
PIN
Meaning
PIN
Meaning
1.
TMDS Data2+
10.
TMDS Clock+
2.
TMDS Data2 Shield
11.
TMDS Clock Shield
3.
TMDS Data2-
12.
TMDS Clock-
4.
TMDS Data1+
13.
CEC
5.
TMDS Data1 Shield
14.
Reserved (N.C. on device)
6.
TMDS Data1-
15.
SCL
7.
TMDS Data0+
16.
SDA
8.
TMDS Data0 Shield
17.
DDC/CEC Ground
9.
TMDS Data0-
18.
+5V Power
19.
Hot Plug Detect
* only for certain models
*19-Pin Color Display Signal Cable
PIN NO.
DESCRIPTION
7.
MHL+
9.
MHL-
18.
VBUS
19.
CBUS
5, 11, 17
GND
*Only for MHL models
EN-6
STANDARD TIMING TABLE
Mode
1
2
3
4
5
6
7
8
9
10
11
12
13
14
MAC
VESA
SVGA
SVGA
XGA
XGA
VESA
SXGA
VESA
WXGA
WXGA+
WSXGA+
UXGA
Resolution
640x480
60
Hz
640x480
66.66 Hz
720x400
70
Hz
800x600
56
Hz
800x600
60
Hz
1024x768
60
Hz
1024x768
70
Hz
1152x864
75
Hz
1280x1024
60
Hz
1280x720
60
Hz
1280x800
60
Hz
1440x900
60
Hz
1680x1050
60
Hz
1920x1080
60
Hz
*Only for MHL-Model
Mode
Resolution
1
640x480 @60Hz
2
720x480p @60Hz
3
720x576p @50Hz
4
800x600 @60Hz
5
1024x768 @60Hz
6
1280x720p @60Hz
7
1280x720p @50Hz
8
1920x1080p @30Hz
EN-7
INSTALLATION
To install the monitor to your host system, please follow the steps as given
below:
Steps
1. 1-1 Connect Video Cable
a. Make sure both the monitor and computer are powered-OFF.
b. Connect the VGA video cable to the computer.
1-2 Connect the digital cable (only for Dual-Input Model).
a. Make sure both the monitor and computer are powered-OFF.
b. Connect one end of the 24-pin DVI cable to the back of the
monitor and connect the other end to the computer’s port.
Or connect HDMI Cable (Only for HDMI-Input Model)(Optional)
a. Make sure both the monitor and computer are powered-OFF.
b. Connect the HDMI cable to the computer.
Connect
HDMI Cable (Only for HDMI-Input Model)(Optional)
1-3
a. Make sure both the monitor and computer are powered-OFF.
b. Connect the HDMI cable to computer. Or connect MHL cable
Or connect MHL cable(Only for MHL-Input Model)(Optional)
to the portable device.
1-4 Connect the Audio Cable (Only Audio-Input Model)(Optional)
2. Connect the adapter
a Connect the AC cord to the adapter.
b Connect one end of the adapter to the monitor and the other end to
a properly grounded, AC outlet .
3. Power-ON Monitor and Computer
Power-ON the monitor first, then power-ON the computer.
This sequence is very important.
4. If the monitor still does not function properly, please refer to the
troubleshooting section to diagnose the problem.
VGA
DC-IN
HDMI
DVI-D IN
VGA IN
AUDIO IN
*Only for MHL-Input Model
EN-8
MHL (Mobile High-Definition Link) (Only for MHL-input Models)
Mobile High-Definition Link is a digital interface for transmitting video and audio from
an external portable device. It is also capable of charging a portable device
(5 V @ 500 mA).
Connecting the devices
Plug the MHL-certified cable into the display's HDMI® (MHL) port and the portable
device's HDMI®-out port.
MHL
Using MHL
MHL-certified portable devices will automatically display content on the monitor,
provided the output display and audio formats are supported by the portable device.
When the portable device is in standby mode, the monitor will show a black screen or
turn to standby mode, depending on the portable device's output signal.
Due to the difference in size and resolution between the monitor and the portable
device, you may find the display quality not as crisp as it appears on the portable device.
This may be due to the portable device changing the output format.
This monitor only receives content from the portable device. It is not capable of
controlling the portable device.
EN-9
USER CONTROLS
Power Switch / Power LED:
To turn the monitor ON or OFF.
Lights up to indicate the power is turned ON.
Using the Shortcut Menu
Press the function button to open the shortcut menu. The shortcut menu lets you
quickly select the most commonly accessed settings.
Empowering:
Press the Empowering Key to open the Acer eColor Management OSD and access
the scenario modes.
AUTO Auto Adjust:
Press this button to activate the Auto Adjustment function. The Auto Adjustment
function is used to set the HPos, VPos, Clock and Focus.
MENU OSD functions:
Press this botton to activate the OSD menu.
Volume Up/Down:
Press to adjust volume(only Audio-Input Mode)(Optional).
INPUT Input Key:
Use Input key to select from different video sources that may be connected to
your monitor.
(a) VGA input
(b) DVI input
(c) HDMI input
(d) HDMI(MHL) input
As you cycle through the sources you will see the following messages on right top
side of screen to indicate currently selected input source. It may take 1 or 2
seconds for the image to appear.
VGA or DVI
If either VGA or DVI input is selected ,but the VGA and DVI cables are not connected, a floating dialog box indicates:
“No Cable Connect” or “No Signal”
EN-10
Acer eColor Management
Operation instructions
Step 1: Press “
” Key to open the Acer eColor Management OSD and access
the scenario modes
Step 2: Press “W“ or “X” to select the mode
Step 3: Press “ AUTO “ Key to confirm the mode and run Auto Adjust.
Features and Benefits
Main
Menu icon
Sub Menu
icon
Sub Menu
item
Description
N/A
User mode User defined. Settings can be fine-tuned to
suit any situation
N/A
ECO mode Adjusts the settings to reduce power
consumption.
N/A
Standard
mode
N/A
Grahpic
mode
N/A
Movie
mode
Default Setting. Reflects native display
capability
Enhances colors and emphasize fine detail.
Pictures and photographs appear in vibrant
colors with sharp detail.
Displays scenes in clearest detail. Presents
great visuals, even in unsuitably-lit
environments.
EN-11
Adjusting the OSD settings
Note: The following content is for general reference only. Actual
product specifications may vary.
The OSD can be used for adjusting the settings of your LCD Monitor.
Press the MENU key to open the OSD. You can use the OSD to adjust the
picture quality, OSD position and general settings. For advanced settings,
please refer to following page:
Adjusting the picture quality
1 Press the MENU key to bring up the OSD.
2 Using the e/ f keys, select
Picture from the OSD. Then navigate to the
picture element you wish to adjust.
3 Use the e/ f keys to adjust the sliding scales.
4 The Picture menu can be used to adjust the current Brightness, Contrast,
Colour Temp, Auto Config and other image-related qualities.
EN-12
Adjusting the OSD position
1 Press the MENU key to bring up the OSD.
2 Using the directional keys, select
OSD from the on screen display. Then
navigate to the feature you wish to adjust.
EN-13
Adjusting the setting
1 Press the MENU key to bring up the OSD.
2 Using the e/ f keys, select
Setting from the OSD. Then navigate to
the feature you wish to adjust.
3 The Setting menu can be used to adjust the screen Menu Language and
other important settings.
EN-14
Product information
Information
1920 x 1080
H:65KHz V:60Hz
VGA Input
S/N:ETL5309 1326350380B3742
1 Press the MENU key to bring up the OSD.
2 Using the e/ f keys, select
Information from the OSD. Then the basic
information of LCD monitor will show up for current input.
EN-15
TROUBLESHOOTING
Before sending your LCD monitor for servicing, please check the troubleshooting list below to see if you can self-diagnose the problem.
(VGA Mode)
Problems
Current Status Remedy
LED ON
·
Using OSD, adjust brightness and contrast
to maximum or reset to their default
settings.
LED OFF
·
Check the power switch.
·
Check if AC power cord is properly
connected to the monitor.
·
Check if video signal cable is properly
connected at the back of monitor.
·
Check if the power of computer system is
ON.
Unstable
Picture
·
Check if the specification of graphics
adapter and monitor is in compliance
which may be causing the input signal
frequency mismatch.
Display is
missing, center
shift, or too
small or too
large in display
size
·
Using OSD, adjust RESOLUTION, CLOCK,
CLOCK-PHASE, H-POSITION and VPOSITION with non-standard signals.
·
Using OSD, in case of missing full-screen
image, please select other resolution or
other vertical refresh timing.
·
Wait for a few seconds after adjusting the
size of the image before changing or
disconnecting the signal cable or powering
OFF the monitor.
·
Check the audio cable with the host PCis
connected.
·
Check if the volume setup of the hostPC is
in minimum position and try toraise the
volume level.
No Picture
LED displays
Amber
Abnormal
Picture
Abnormal
Sound(Only
Audio-Input
model)
(Optional)
No sound, or
sound level is
too low
EN-16
(DVI/HDMI/MHL cable)
Problems
Current Status Remedy
LED ON
·
Using OSD, adjust brightness and
contrast to maximum or reset to their
default settings.
LED OFF
·
Check the power switch.
·
Check if AC power cord is properly
connected to the monitor.
·
Check if video signal cable is properly
connected at the back of monitor.
·
Check if the power of computer system
is ON.
·
Check the audio cable with the host PCis
connected.
·
Check if the volume setup of the hostPC is
in minimum position and try toraise the
volume level.
No Picture
LED displays
Amber
Abnormal
Sound(Only
Audio-Input
model)
(Optional)
No sound, or
sound level is
too low
EN-17
Acer Incorporated
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi
New Taipei City 221, Taiwan
Declaration of Conformity
We,
Acer Incorporated
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi, New Taipei City 221, Taiwan
Contact Person: Mr. RU Jan, e-mail:ru.jan@acer.com
And,
Acer Italy s.r.l
Via Lepetit, 40, 20020 Lainate (MI) Italy
Tel: +39-02-939-921 ,Fax: +39-02 9399-2913
www.acer.it
Declare under our own respons
Product:
Trade Name:
Model Number:
SKU Number:
•
•
•
•
•
LCD Monitor
Acer
Q226HQL;Q236HL;Q276HL
Q226HQL xxxxxx; Q236HL xxxxxx; Q276HL xxxxxx
(“x” = 0~9, a ~ z, A ~ Z, or blank)
To which this declaration refers conforms to the relevant standard or other standardizing documents:
EN55022:2006/A1:2007 Class B; EN55024:2010
EN 61000-3-2:2006+A1:2009+A2:2009, Class D
EN61000-3-3:2008
EN60950-1:2006/A11:2009/A1:2010+A12:2011
EN50581:2012
We hereby declare above product is in compliance with the essential requirements and other relevant
provisions of EMC Directive 2004/108/EC, Low Voltage Directive 2006/95/EC, and RoHS Directive
2011/65/EU and Directive 2009/125/EC with regard to establishing a framework for the setting of ecodesign
requirements for energy-related product.
Year to begin affixing CE marking 2013.
_______________________________
RU Jan / Sr. Manager
Regulation, Acer Inc.
Sep. 27, 2013
Date
Acer America Corporation
:HVW6DQ&DUORV6W6XLWH6DQ-RVH
CA 95110, U. S. A.
Tel : 254-298-4000
Fax : 254-298-4147
www.acer.com
Federal Communications Commission
Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
The following local Manufacturer /Importer is responsible for this declaration:
Product:
LCD Monitor
Model Number:
Q226HQL; Q236HL; Q276HL
SKU Number:
Q226HQL xxxxxx; Q236HL xxxxxx;
Q27 6HL xxxxxx
(“x” = 0~9, a ~ z, A ~ Z or Blank)
Name of Responsible Party:
Acer America Corporation
Address of Responsible Party: 333 West San Carlos St.
Suite 1500
San Jose, CA 95110
U. S. A.
Contact Person:
Acer Representative
Phone No.:
254-298-4000
Fax No.:
254-298-4147
English
For any customers who own the EPEAT Gold registered models1, Acer offers the following services at your
costs2:
1. Additional 3 years warranty for product life cycle extension
2. For the product life extension, through the use of compatible parts of after-market, or refurbished with equal or higher
specification, we offer spare parts or replacement parts for 5 years after end of production
For those INSTITUTIONAL customers who own the EPEAT Gold registered models1, Acer offers following
additional services at your costs2:
1. Product recycling program of aging Notebooks, Desktops and Monitors
2. Battery recycling program of aging Battery Pack of Notebooks and Coin Battery on PCBs
3. Packaging recycling program3 for product related unwanted packaging after installing EPEAT registered1 Notebooks,
Desktop and Monitor products
For more detail information of above services such as additional warranty EPEAT registered models 1, please visit
Acer website or contact local designated contact person
1
2
3
Qualified EPEAT registered models, please visit http://ww2.epeat.net/searchoptions.aspx.
Costs vary by country, for details, contacts and applicability refer to local country web site.
Service for Packaging ecycling program are available in limited countries, please call Acer local Customer Center for details.
Deutsch
Für alle Kunden, die ein registriertes EPEAT Gold Modell besitzen1, bietet Acer folgende kostenpflichtigen
Dienste an2:
1. 3 Jahre zusätzliche Garantie als Produkt Lebensverlängerung
2. Für die Produkt Lebensverlängerung, die durch die Benutzung von kompatiblen Teilen des Nachfolgemarktes oder
wieder aufbereiteten Teilen mit gleicher oder besserer Spezifikation zustande kommt, bieten wir Ersatzteile oder
Austauschteile bis zu 5 Jahren nach Produktionsende an
Für diese BEVORZUGTEN Kunden die eines der registrierten EPEAT Gold Modelle besitzen1, bietet Acer
folgende kostenpflichtigen Dienste an2:
1. Produkt Recycling Programm für alte Notebooks, PC’s und Bildschirme
2. Batterie Recycling Programm für alte Notebook Batterien und Knopfzellenbatterien auf Leiterplatten
3. Verpackungsrecycling Programm3 für Produktbezogene unerwünschter Verpackung nach Installation der EPEAT
registrierten1 Notebooks, PC’s und Bildschirmen
Für weitere Details zu den o. g. Diensten wie z.B. weitere registrierte EPEAT Modelle1, besuchen Sie bitte die
Acer website oder kontaktieren die designierte lokale Kontaktperson
1
2
3
Für qualifizierte EPEAT Modelle, besuchen Sie bitte http://ww2.epeat.net/searchoptions.aspx.
Kosten variieren von Land zu Land, für Details, Kontakte und Verfügbarkeit beziehen Sie sich bitte auf die lokalen Webseiten des jeweiligen
Landes
Dienste für das Verpackungs Recycling Programm sind nicht in allen Ländern erhältlich, bitte kontaktieren Sie hierfür das lokale
Kundendienstcenter für weitere Details
繁體中文
1
2
對於擁有登錄為 EPEAT Gold 產品 的客戶,為了延長產品使用年限,宏碁提供以下服務 :
1. 除了基本保固外,另提供 3 年延長保固
2. 對於延長產品使用年限,經由使用相容的零件、市場取得或更高規格的翻新零件,我們提供產品停產後 5 年零件替
換服務
1
2
對於擁有登錄為 EPEAT Gold 產品 的政府機關、學校客戶,宏碁提供以下的服務 :
1. 筆記型電腦、桌上型電腦及螢幕的產品回收
2. 筆記型電腦及主機板上鈕釦型電池的回收
3
3. 筆記型電腦、桌上型電腦及螢幕產品的包材回收
對於上述服務,如額外保修條款、更多的詳細資訊及登錄為 EPEAT Gold 產品型號,請洽宏碁官方網站
1
2
3
合格登錄為 EPEAT 註冊產品,請至 http://ww2.epeat.net/searchoptions.aspx.
產品延長保固、相關替代品項費用,請洽宏碁官方網站
包材回收服務,因各個國家或地區有所不同,請洽宏碁官方網站。
ENERGY STAR®
Acer’s ENERGY STAR qualified products save you money by reducing energy costs and helps
protect the environment without sacrificing features or performance. Acer is proud to offer our
customers products with the ENERGY STAR mark.
What is ENERGY STAR?
Products that are ENERGY STAR qualified use less energy and prevent greenhouse gas
emissions by meeting strict energy efficiency guidelines set by the U.S. Environmental Protection
Agency. Acer is committed to offer products and services worldwide that help customers save
money, conserve energy and improve the quality of our environment. The more energy we can
save through energy efficiency, the more we reduce greenhouse gases and the risks of climate
change. More information refers to http://www.energystar.gov or
http://www.energystar.gov/powermangement
Acer ENERGY STAR qualified products:
•Produce less heat and reduce cooling loads, and warmer climates.
•Automatically go into “display sleep” and “computer sleep” mode after 15 and 30 minute of
inactivity respectively.
•Wake the monitor when it is in Active Off mode, move the mouse or press any keyboard key.
•Computers will save more than 80% energy at “sleep” mode.
ENERGY STAR and the ENERGY STAR mark are registered U.S. marks
Download PDF

advertising