Acer | HA220Q | Acer HA220Q User Manual

Acer LCD Monitor
User Guide
Copyright © 2016. Acer Incorporated.
All Rights Reserved.
English
Acer LCD Monitor User Guide
Original Issue: 07/2016
Changes may be made periodically to the information in this publication without obligation to notify
any person of such revisions or changes. Such changes will be incorporated in new editions of this
manual or supplementary documents and publications. This company makes no representations or
warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims
the implied warranties of merchantability or fitness for a particular purpose.
Record the model number, serial number, purchase date and place of purchase information in the
space provided below. The serial number and model number are recorded on the label affixed to
your computer. All correspondence concerning your unit should include the serial number, model
number and purchase information.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any
form or by any means, electronically, mechanically, by photocopy, recording or otherwise, without
the prior written permission of Acer Incorporated.
Acer LCD Monitor User Guide
Model number: __________________________________
Serial number: ___________________________________
Date of purchase: ________________________________
Place of purchase: ________________________________
Acer and the Acer logo are registered trademarks of Acer Incorporated. Other companies’ product
names or trademarks are used herein for identification purposes only and belong to their respective
companies.
Special notes on LCD monitors
The following are normal with the LCD monitor and do not indicate a problem.
Due to the nature of the fluorescent light, the screen may flicker during initial
use. Turn off the power switch and then turn it on again to make sure the flicker
disappears.
•
You may find slightly uneven brightness on the screen depending on the desktop
pattern you use.
•
The LCD screen has 99.99% or more effective pixels. It may include blemishes of
0.01% or less such as a missing pixel or pixel lit all the time.
•
Due to the nature of the LCD screen, an afterimage of the previous screen may
remain after switching the image, when the same image is displayed for hours. In this
case, the screen is recovered slowly by changing the image or turning off the power
switch for a few hours.
English
•
Information for your safety and
comfort
Safety instructions
Read these instructions carefully. Keep this document for future reference. Follow all
warnings and instructions marked on the product.
Cleaning your monitor
Please carefully follow these guidelines when cleaning the monitor:
•
Always unplug the monitor before cleaning.
•
Use a soft cloth to wipe the screen and cabinet front and sides.
Connecting/disconnecting the device
Observe the following guidelines when connecting and disconnecting power from the
LCD monitor:
•
Make sure the monitor is attached to its base before connecting the power cord to
the AC power outlet.
•
Make sure both the LCD monitor and the computer are turned off before
connecting any cable or unplugging the power cord.
•
If the system has multiple sources of power, disconnect power from the system by
unplugging all power cords from the power supplies.
iii
Accessibility
English
Be sure that the power outlet you plug the power cord into is easily accessible and
located as close to the equipment operator as possible. When you need to disconnect
power from the equipment, be sure to unplug the power cord from the electrical outlet.
Safe listening
To protect your hearing, follow these instructions.
•
Gradually increase the volume until you can hear it clearly and comfortably and
without distortion.
•
After setting the volume level, do not increase it after your ears have adjusted.
•
Limit the amount of time listening to music at high volume.
•
Avoid turning up the volume to block out noisy surroundings.
•
Turn the volume down if you can’t hear people speaking near you.
Warnings
•
Do not use this product near water.
•
Do not place this product on an unstable cart, stand or table. If the product falls, it
could be seriously damaged.
•
Slots and openings are provided for ventilation to ensure reliable operation of the
product and to protect it from overheating. These openings must not be blocked
or covered. The openings should never be blocked by placing the product on a bed,
sofa, rug or other similar surface. This product should never be placed near or over
a radiator or heat register, or in a built-in installation unless proper ventilation is
provided.
•
Never push objects of any kind into this product through cabinet slots as they may
touch dangerous voltage points or short-out parts that could result in a fire or
electric shock. Never spill liquid of any kind onto or into the product.
•
To avoid damage of internal components and to prevent battery leakage, do not
place the product on a vibrating surface.
•
Never use it under sporting, exercising, or any vibrating environment which will
probably cause unexpected short current or damage internal devices.
Using electrical power
•
•
iv
This product should be operated from the type of power indicated on the marking
label. If you are not sure of the type of power available, consult your dealer or local
power company.
Do not allow anything to rest on the power cord. Do not locate this product where
people will walk on the cord.
If an extension cord is used with this product, make sure that the total ampere rating
of the equipment plugged into the extension cord does not exceed the extension
cord ampere rating. Also, make sure that the total rating of all products plugged into
the wall outlet does not exceed the fuse rating.
• Do not overload a power outlet, strip or receptacle by plugging in too many devices.
The overall system load must not exceed 80% of the branch circuit rating. If power
strips are used, the load should not exceed 80% of the power strip’s input rating.
• This product’s power cord is equipped with a three-wire grounded plug. The
plug only fits in a grounded power outlet. Make sure the power outlet is properly
grounded before inserting the power cord plug. Do not insert the plug into a nongrounded power outlet. Contact your electrician for details.
Warning! The grounding pin is a safety feature. Using a power
outlet that is not properly grounded may result in electric
shock and/or injury.
Note: The grounding pin also provides good protection from
unexpected noise produced by other nearby electrical devices that
may interfere with the performance of this product.
•
Use the product only with the supplied power supply cord set. If you need to
replace the power cord set, make sure that the new power cord meets the following
requirements: detachable type, UL listed/CSA certified, type SPT-2, rated 7 A 125 V
minimum, VDE approved or its equivalent, 4.6 meters (15 feet) maximum length.
Product servicing
Do not attempt to service this product yourself, as opening or removing covers may
expose you to dangerous voltage points or other risks. Refer all servicing to qualified
service personnel.
Unplug this product from the wall outlet and refer servicing to qualified service
personnel when:
•
the power cord or plug is damaged, cut or frayed
•
liquid was spilled into the product
•
the product was exposed to rain or water
•
the product has been dropped or the case has been damaged
•
the product exhibits a distinct change in performance, indicating a need for service
•
the product does not operate normally after following the operating instructions
v
English
•
English
Note: Adjust only those controls that are covered by the operating
instructions, since improper adjustment of other controls may result
in damage and will often require extensive work by a qualified
technician to restore the product to normal condition.
Potentially explosive environments
Switch off your device in any area with a potentially explosive atmosphere and obey all
signs and instructions. Potentially explosive atmospheres include areas where you would
normally be advised to turn off your vehicle engine. Sparks in such areas could cause
an explosion or fire resulting in bodily injury or even death. Switch off the device near
gas pumps at service stations. Observe restrictions on the use of radio equipment in fuel
depots, storage and distribution areas; chemical plants; or where blasting operations are
in progress. Areas with a potentially explosive atmosphere are often, but not always,
marked. They include below deck on boats, chemical transfer or storage facilities,
vehicles using liquefied petroleum gas (such as propane or butane), and areas where the
air contains chemicals or particles such as grain, dust or metal powders.
Additional safety information
Your device and its enhancements may contain small parts. Keep them out of the reach
of small children.
IT Equipment Recycling Information
Acer is strongly committed to environmental protection and views recycling, in the form
of salvaging and disposal of used equipment, as one of the company’s top priorities in
minimizing the burden placed on the environment.
We at Acer are very conscious of the environmental effects of our business and strive to
identify and provide the best working procedures to reduce the environmental impact
of our products.
For more information and help when recycling, please go to this website:
http://www.acer-group.com/public/Sustainability/sustainability
Visit www.acer-group.com for further information on the features and benefits of our
other products.
Disposal instructions
Do not throw this electronic device into the trash when discarding.
To minimize pollution and ensure utmost protection of the global
environment, please recycle. For more information on the Waste
from Electrical and Electronics Equipment (WEEE) regulations, visit
http://www.acer-group.com/public/Sustainability/sustainability
vi
LCD pixel statement
English
The LCD unit is produced with high-precision manufacturing techniques. Nevertheless,
some pixels may occasionally misfire or appear as black or red dots. This has no effect on
the recorded image and does not constitute a malfunction.
This product has been shipped enabled for power management:
•
Activate display’s Sleep mode within 5 minutes of user inactivity.
•
Wake the monitor when it is in Active Off mode, move the mouse or press any
keyboard key.
Tips and information for comfortable use
Computer users may complain of eyestrain and headaches after prolonged use. Users are
also at risk of physical injury after long hours of working in front of a computer. Long
work periods, bad posture, poor work habits, stress, inadequate working conditions,
personal health and other factors greatly increase the risk of physical injury.
Incorrect computer usage may lead to carpal tunnel syndrome, tendonitis, tenosynovitis
or other musculoskeletal disorders. The following symptoms may appear in the hands,
wrists, arms, shoulders, neck or back:
•
numbness, or a burning or tingling sensation
•
aching, soreness or tenderness
•
pain, swelling or throbbing
•
stiffness or tightness
•
coldness or weakness
If you have these symptoms, or any other recurring or persistent discomfort and/or pain
related to computer use, consult a physician immediately and inform your company’s
health and safety department.
The following section provides tips for more comfortable computer use.
Finding your comfort zone
Find your comfort zone by adjusting the viewing angle of the monitor, using a footrest,
or raising your sitting height to achieve maximum comfort. Observe the following tips:
•
refrain from staying too long in one fixed posture
•
avoid slouching forward and/or leaning backward
•
stand up and walk around regularly to remove the strain on your leg muscles
vii
Taking care of your vision
English
Long viewing hours, wearing incorrect glasses or contact lenses, glare, excessive room
lighting, poorly focused screens, very small typefaces and low-contrast displays could
stress your eyes. The following sections provide suggestions on how to reduce eyestrain.
Eyes
•
Rest your eyes frequently.
•
Give your eyes regular breaks by looking away from the monitor and focusing on a
distant point.
•
Blink frequently to keep your eyes from drying out.
Display
•
Keep your display clean.
•
Keep your head at a higher level than the top edge of the display so your eyes point
downward when looking at the middle of the display.
•
Adjust the display brightness and/or contrast to a comfortable level for enhanced
text readability and graphics clarity.
•
Eliminate glare and reflections by:
•
placing your display in such a way that the side faces the window or any light
source
•
minimizing room light by using drapes, shades or blinds
•
using a task light
•
changing the display’s viewing angle
•
using a glare-reduction filter
•
using a display visor, such as a piece of cardboard extended from the display’s top
front edge
•
Avoid adjusting your display to an awkward viewing angle.
•
Avoid looking at bright light sources, such as open windows, for extended periods of
time.
Developing good work habits
Develop the following work habits to make your computer use more relaxing and
productive:
viii
•
Take short breaks regularly and often.
•
Perform some stretching exercises.
•
Breathe fresh air as often as possible.
•
Exercise regularly and maintain a healthy body.
Acer Incorporated
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi
New Taipei City 221, Taiwan
English
Declaration of Conformity
We,
Acer Incorporated
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi, New Taipei City 221, Taiwan
And,
Acer Italy s.r.l.
Via Lepetit, 40, 20020 Lainate (MI) Italy
Tel: +39-02-939-921 ,Fax: +39-02 9399-2913
www.acer.it
Product:
Trade Name:
Model Number:
SKU Number:
LCD Monitor
ACER
HA220Q/HA230/HA240Y/HA270
HA220Q/HA230/HA240Y/HA270
xxxxxx;
(“x” = 0~9, a ~ z, A ~ Z, or blank)
We, Acer Incorporated, hereby declare under our sole responsibility that the product described above is in
conformity with the relevant Union harmonization legislations as below Directive and following harmonized
standards and/or other relevant standards have been applied:
EMC Directive: 2014/30/EU
EN 55022:2010+AC:2011 Class B
EN 55024:2010
EN 61000-3-2:2006+A2:2009 Class D
EN 61000-3-3:2013
LVD Directive: 2014/35/EU
EN 60950-1:2006/A11:2009/A1:2010/A12:2011/A2:2013
RoHS Directive: 2011/65/EU
EN 50581:2012
ErP Directive: 2009/125/EC
Regulation (EC) No. 1275/ 2008; EN 50564:2011
Year to begin affixing CE marking: 2016.
_______________________________
RU Jan / Sr. Manager
Regulation, Acer Inc.
July 29,2016
Date
ix
Acer America Corporation
English
333 West San Carlos St., San Jose
Suite 1500
CA 95110, U. S. A.
Tel : 254-298-4000
Fax : 254-298-4147
www.acer.com
Federal Communications Commission
Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
The following local Manufacturer /Importer is responsible for this declaration:
x
Product:
LCD Monitor
Model Number:
HA220Q/HA230/HA240Y/HA270
SKU Number:
HA220Q/HA230/HA240Y/HA270 XXXXXX
Name of Responsible Party:
Acer America Corporation
Address of Responsible Party:
333 West San Carlos St.
Suite 1500
San Jose, CA 95110
U. S. A.
Contact Person:
Acer Representative
Phone No.:
254-298-4000
Fax No.:
254-298-4147
(“x” = 0~9, a ~ z, or A ~ Z)
iii
iii
iii
iv
iv
iv
iv
v
vi
vi
vii
vii
viii
xi
Unpacking1
Attaching the base (for selected models) Screen position adjustment
Connecting the adapter and AC Power cord Power saving
Display Data Channel (DDC)
Connector pin assignment
15-pin color display signal cable
24-pin color display signal cable
19-pin color display signal cable
2
3
3
3
4
4
4
4
5
Standard timing table
6
Installation7
Users controls
8
Panel controls
Using the Shortcut Menu
Input Source Selection
Acer eColor Management
Operation instructions
Features and benefits
Using the OSD Menus Picture Menu
OSD Menu
Setting Menu
8
9
9
10
10
10
11
11
12
13
English
Safety instructions
Cleaning your monitor
Connecting/disconnecting the device
Accessibility
Safe listening
Warnings
Using electrical power
Product servicing
Additional safety information
IT Equipment Recycling Information
Disposal instructions
LCD pixel statement
Tips and information for comfortable use
Federal Communications Commission
Declaration of Conformity
iii
iii
Contents
Special notes on LCD monitors
Information for your safety and comfort
Information Menu
14
English
Troubleshooting15
VGA Mode
DVI/HDMI Mode (Optional)
15
16
Unpacking
LCD monitor
Quick start guide
D-sub cable
HDMI cable
(Optional)
DVI cable
(Optional)
AC Adapter
English
Please check that the following items are present when you unpack the box, and save
the packing materials in case you need to ship or transport the monitor in the future.
Audio cable
(Optional)
AC Power cord
1
Attaching the base (for selected models)
English
Note: Remove the monitor and monitor base from its packaging.
Carefully place the monitor face-down on a stable surface -- use a
cloth to avoid scratching the screen.
1
Attach the monitor stand arm to the base.
2
Ensure that the base is locked onto the monitor stand arm.
• Secure the base to the monitor stand arm by turning the white screw using the
integrated tab or a suitable coin. (for selected models)
Note: Take care when performing the installation to avoid injuring
yourself.
2
Screen position adjustment
English
To optimize the viewing position, you can adjust the
monitor tilt, using both of your hands to hold the edges
of the monitor. The monitor can be adjusted to 15
degrees up or 5 degrees down.
Connecting the adapter and AC Power cord
• Check first to make sure that the power cord you use is the correct type required for
your area.
• The monitor has a universal power supply that allows operation in either 100/120 V
AC or 220/240 V AC voltage area. No user-adjustment is required.
• Plug one end of the AC power cord to the Adapter, and plug the other end into an
AC outlet.
• For units using 120 V AC:
Use a UL-listed cord set, type SVT wire and plug rated 10 A/125 V.
• For units using 220/240 V AC:
Use a cord set consisting of H05VV-F cord and plug rated 10 A/250 V. The cord set
should have the appropriate safety approvals for the country in which the equipment
will be installed.
Power saving
The monitor will be switched to “power saving” mode by the control signal from the
display controller, as indicated by the blinking blue light.
Mode
LED light
On
Blue
Standby/Power saving
Blinking Blue
The power saving mode will be kept until a
control signal has been detected or the keyboard
or mouse is activated. The recovery time from
“power saving” mode back to “on” is around 3
seconds.
3
Display Data Channel (DDC)
English
To make installation easier, so long as your system supports the DDC protocol, the
monitor is able to plug-and-play. The DDC is a communication protocol through which
the monitor automatically informs the host system about its capabilities; for example,
supported resolutions and corresponding timing. The monitor supports the DDC2B
standard.
Connector pin assignment
1
15-pin color display signal cable
PIN No.
1
Description
Red
PIN No.
9
5
10
6
11
15
Description
+5 V
2
Green
10
Logic ground
3
Blue
11
Monitor ground
4
Monitor ground
12
DDC-serial data
5
DDC-return
13
H-sync
6
R-ground
14
V-sync
7
G-ground
15
DDC-serial clock
8
B-ground
24-pin color display signal cable
PIN No.
4
Description
PIN No.
Description
1
TMDS data 2-
13
NC
2
TMDS data 2+
14
+5 V power
3
TMDS data 2/4 shield
15
DVI detect
4
NC
16
Hot-plug detection
5
NC
17
TMDS data 0-
6
DDC clock
18
TMDS data 0+
7
DDC data
19
TMDS data 0/5 shield
8
NC
20
NC
9
TMDS data 1-
21
NC
10
TMDS data 1+
22
TMDS clock shield
11
TMDS data 1/3 shield
23
TMDS clock+
12
NC
24
DDC TMDS clock-
19-pin color display signal cable
19 17 15 13 11 9 7 5 3 1
PIN No.
Description
PIN No.
English
18 16 1412 10 8 6 4 2
Description
1
TMDS Data2+
2
TMDS Data2 Shield
3
TMDS Data2-
4
TMDS Data1+
5
TMDS Data1 Shield
6
TMDS Data1-
7
TMDS Data0+
8
TMDS Data0 Shield
9
TMDS Data0-
10
TMDS Clock+
11
TMDS Clock Shield
12
TMDS Clock-
13
CEC
14
Reserved (N.C. on device)
15
SCL
16
SDA
17
DDC/CEC Ground
18
+5V Power
19
Hot Plug Detect
5
Standard timing table
No.
English
1
2
Mode
VGA
640x480
Refresh Rate
60
Hz
640x480
72
Hz
3
MAC
640x480
66.7
Hz
4
VESA
720x400
70
Hz
800x600
56
Hz
800x600
60
Hz
5
6
SVGA
7
800x600
72
Hz
8
1024x768
60
Hz
1024x768
70
Hz
1152x864
75
Hz
9
10
11
XGA
VESA
1280x960
60
Hz
12
SXGA
1280x1024
60
Hz
13
VESA
1280x720
60
Hz
1280x800
60
Hz
14
15
6
Resolution
WXGA
1360x768
60
Hz
16
WXGA+
1440x900
60
Hz
17
WSXGA+
1680x1050
60
Hz
18
UXGA
1600x1200
60
Hz
19
VESA
1920x1080
60
Hz
Installation
To install the monitor on your host system, please follow the steps below:
English
Steps
1 Connect cable(s)
a Make sure both the monitor and computer are switched off.
b Connect the VGA video cable to the computer.
c Connect DVI Cable (Optional, only Dual-Input Model)to the computer.
d Connect the HDMI Cable (Optional, only HDMI-Input Model)to the computer.
e Connect the audio cable (Optional, only Audio-input Model)to the computer.
2
Connect the adapter
a Connect the AC cord to the adapter.
b Connect one end of the adapter to the monitor and the other end to a properly
grounded, AC outlet.
3
Turn on the monitor and computer
Turn on the monitor first, then the computer. This sequence is very important.
4
If the monitor does not function properly, please refer to the troubleshooting section
to diagnose the problem.
Note: Audio output is only for audio output model.
In order to prevent damage to the monitor, do not lift the monitor by its base.
7
English
Users controls
Panel controls
No.
Item
Description
1
Power button/
indicator
Turn the monitor on/off.
Blue indicates power on. Blinking blue indicates standby/
power saving mode.
2
< / > button
Press the < / > button to navigate to the desired function,
and press the Menu button to select the function. Press the
< / > button to change the settings of the current function.
3
Menu/Enter
button
Press to view the OSD menu. Press it again to enter a
selection in the OSD menu.
4
Auto/Exit button
•
•
5
8
Empowering Key
When the OSD menu is active, press this button to exit
the OSD menu.
When the OSD menu is inactive, press this button for
two seconds to activate the Auto Adjustment function
and the monitor will automatically optimize the display
position, focus, and clock of your display.
Press this button to open the Acer eColor Management OSD
and access the scenario modes.
AUTO
English
Using the Shortcut Menu
Input
Press any of the function buttons (Empowering Key, Auto button, Menu button )
to open the shortcut menu. The shortcut menu lets you quickly select the most commonly
accessed settings.
Icon
AUTO
Input
Item
Description
Empowering
Press the Empowering Key to open the Acer eColor
Management and access the scenario modes.
Auto
Press the Auto button to activate the Auto Adjustment
function and the monitor will automatically optimize the
display position, focus, and clock of your display.
Menu
Press the Menu button to activate the OSD menu.
Volume
Press the Volume button to adjust volume. (Optional, only
Audio-Input Model)
Input
Press the Input button to select from different video
sources that may be connected to your monitor. (Optional,
only Dual-Input Model or HDMI-Input Model) When Auto
Source is off, press the “Input” Hot key to display the input
source Menu. User can switch input source, or to control the
“Auto Source” function.
Input Source Selection
Input
Auto Source On
VG A
DVI
HDMI
1. The default of Auto Source is “On”, it can support auto search for signal source in
order.
2. When Auto Source is Off, press the “Input” Hot key to display the input source Menu.
User can switch input source, or to control the “Auto Source” function.
9
Acer eColor Management
English
Operation instructions
1 Press the Empowering Key to open the Acer eColor Management OSD menu and
access the scenario modes.
mpowering Technology
User
ECO
Standard Graphics
Movie
2 Press the < / > button to select the desired mode.
3 Press the Auto button to confirm the selection and exit Acer eColor Management.
Features and benefits
Icon
10
Mode type
Description
User mode
User-defined. Settings can be fine-tuned to suit any
situation.
ECO mode
Adjusts the settings to reduce power consumption.
Standard mode
Default settings. Reflects native display capability.
Graphic mode
Enhances colors and emphasizes fine detail. Pictures and
photographs appear in vibrant colors with sharp detail.
Movie mode
Displays scenes in clearest detail. Presents great visuals,
even in unsuitably-lit environments.
Using the OSD Menus
English
Note: The following content is for general reference only. Actual
product specifications may vary.
Your LCD monitor is equipped with an on-screen display (OSD) menu for making various
adjustments and settings.
Press the Menu button to open the OSD menu. You can use the OSD menu to adjust the picture
quality, OSD timeout, and general settings.
Picture Menu
The Picture menu is used for adjusting the picture quality.
Picture
Acer eColor Management
Blue Light
On
Brightness
70
Contrast
50
H.Position
20
V.Position
50
Focus
70
Clock
50
1 Press the Menu button to bring up the OSD menu.
Picture and press the Menu button to enter the
2 Press the < / > button to select
Picture menu.
The following options are available in the Picture menu: Acer ecolor Management,
Blue Light, Brightness, Contrast, H. Position, V. Position, Focus, Clock, Colour Temp,
and Auto Config.
3 Press the < / > button to scroll through the Picture options, and press the Menu
button to enter its sub-menu.
4 Press the < / > button to adjust/select the setting and press the Auto button to
confirm.
5 Blue Light: filter out blue light by adjusting different Blue Light showing ratio - 80%,
70%, 60%, 50%.
Note: Higher values allow more blue light through. For the best
protection select a lower value.
11
6 Brightness: Adjust the brightness from 0 to 100.
English
Note: Adjusts the balance between light and dark shades.
7 Contrast: Adjust the contrast from 0 to 100.
Note: Sets the degree of difference between light and dark areas.
8. H.Position: adjust the horizontal position of the picture.
9. V.Position: adjust the vertical position of the picture.
10. Focus: adjust clk phase to ADC.
11. Clock: adjust ADC Clock Fast Lock.
12. Color Temp is for user to adjust the colour temperature from blue light, warm, cool
and user. The default value is warm.
13. 6-axis Saturate: Adjust saturation of red, green, blue, yellow, magenta and cyan.
6-axis Hue: Adjust hue for red, green, blue, yellow, magenta and cyan.
14. Auto Config: Press this button to activate the Auto Adjustment function. The Auto
adjustment function is used to set the HPos, VPos, Clock and Focus. (Only available on
VGA port.)
OSD Menu
The OSD menu is used for adjusting the OSD menu location and the timeout setting.
OSD
OSD Timeout
10
1 Press the Menu button to bring up the OSD menu.
2 Press the < / > button to select
OSD menu.
3 Press the < /
10 seconds.
12
>
OSD and press the Menu button to enter the
button to adjust the OSD Timeout (10 ~ 120 seconds), the default is
Setting Menu
English
The Setting menu is used for adjusting the general settings for current input signal such
as aspect ratio, OSD language, and etc.
Setting
Wide Mode
DDC/CI
OD
Full
ON
Normal
ACM
OFF
Input
VGA
Language
English
AutoSourc
Sourece
Auto
Englis
ON
ON
Quic k Start Mode
OFF
Reset
1 Press the Menu button to bring up the OSD menu.
Setting and press the Menu button to enter the
2 Press the < / > button to select
Setting menu.
The following options are available in the Setting menu: Wide Mode, DDC/CI, OD,
ACM, Input, Language, Auto Source ,Quick Start Mode and Reset.
3 Press the < / > button to scroll through the Setting options, and press the Menu
button to enter its sub-menu.
4 Press the < / > button to adjust/select the setting and press the Auto button to
confirm.
5 Wide mode: You can select which screen aspect you are using. The options are Full,
Aspect, and 1:1.
6 DDC/CI: Allows the monitor settings to be set through the software on the PC.
Note: DDC/CI, short for Display Data Channel/Command Interface,
which allows monitor controls to be sent via software.
7 OD: Select Off, Normal, or Extreme.
8 ACM: Turn ACM on or off. The default is off.
9 Input: Select the source from VGA,DVI, HDMI.
10 Language: Set the OSD menu language.
11 Auto Source:The default is “On”, can support auto search for signal source in order.
12 Quick start mode: Select Off or On. The default is “Off”. Turn on to speed up boot
speed.
13
Information Menu
English
The Information menu displays the basic information of the LCD monitor.
Information
H:68KHz V:60Hz
HDMI Input
S/N:ETRLA00803104000502400
1 Press the Menu button to bring up the OSD menu.
2 To view the basic information of the LCD monitor, press the < / > button to select
Information.
14
Troubleshooting
English
Before sending your LCD monitor for servicing, please check the troubleshooting list
below to see if you can self-diagnose the problem.
VGA Mode
Problem
No picture visible
LED status
Remedy
Blue
Using the OSD menu, adjust brightness and
contrast to maximum or reset to their default
settings.
Off
Check the power switch.
Check if the power cord is properly connected
to the monitor.
Blinking Blue
Check if the video signal cable is properly
connected at the back of monitor.
Check if the computer system is switched on
and in power saving/standby mode.
Unstable picture
Blue
Check if the specification of graphics adapter
and monitor is in compliance which may be
causing the input signal frequency mismatch.
Abnormal picture
(Image is missing,
off-center, too large
or too small on the
screen.)
Blue
Using the OSD menu, adjust focus, clock,
H-position and V-position with non-standard
signals.
Check the display setting on your system. In
case of a missing image, please select another
resolution or vertical refresh rate.
Wait for a few seconds after adjusting
the size of the image before changing or
disconnecting the signal cable or switching
off the monitor.
15
DVI/HDMI Mode (Optional)
English
Problem
No picture visible
LED status
Remedy
Blue
Using the OSD menu, adjust brightness and
contrast to maximum or reset to their default
settings.
Off
Check the power switch.
Check if the AC power cord is properly
connected to the monitor.
Blinking Blue
Check if the video signal cable is properly
connected at the back of monitor.
Check if the computer system is switched on
and in power saving/standby mode.
16
Download PDF