Acer | U5330W | Acer U5230 User Manual

Acer Projector
U5530/U5330W/U5230/R350/R320/R310/
PU-F20/PU-W20/PU-X20/SP150/SP130/
SP110/FU-420/FU-320/FU-120/D1P1801/
DWX1802/DNX1803
User's Guide
Copyright © 2018. Acer Incorporated.
All Rights Reserved.
Acer Projector User's Guide
Original Issue: 06/2018
Changes may be made periodically to the information in this publication without obligation
to notify any person of such revisions or changes. Such changes will be incorporated in new
editions of this manual or supplementary documents and publications. This company makes
no representations or warranties, either expressed or implied, with respect to the contents
hereof and specifically disclaims the implied warranties of merchantability or fitness for a
particular purpose.
Record the model number, serial number, purchase date and place of purchase information in
the space provided below. The serial number and model number are recorded on the label
affixed to your projector. All correspondence concerning your unit should include the serial
number, model number and purchase information.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronically, mechanically, by photocopy, recording or otherwise,
without the prior written permission of Acer Incorporated.
Model number: _________________________________
Serial number: __________________________________
Date of purchase: _______________________________
Place of purchase: ______________________________
Acer and the Acer logo are registered trademarks of Acer Incorporated. Other companies' product
names or trademarks are used herein for identification purposes only and belong to their respective
companies.
"HDMI™, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC."
iii
Information for your safety and
comfort
Read these instructions carefully. Keep this document for future reference.
Follow all warnings and instructions marked on the product.
Turning the product off before cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
Caution for plug as disconnecting device
Observe the following guidelines when connecting and disconnecting power to
the external power supply unit:
•
•
•
Install the power supply unit before connecting the power cord to the AC
power outlet.
Unplug the power cord before removing the power supply unit from the
projector.
If the system has multiple sources of power, disconnect power from the
system by unplugging all power cords from the power supplies.
Caution for Accessibility
Be sure that the power outlet you plug the power cord into is easily accessible
and located as close to the equipment operator as possible. When you need to
disconnect power to the equipment, be sure to unplug the power cord from the
electrical outlet.
Warnings!
•
•
•
•
•
•
Do not use this product near water.
Do not place this product on an unstable cart, stand or table. If the product
falls, it could be seriously damaged.
Slots and openings are provided for ventilation to ensure reliable
operation of the product and to protect it from overheating. These
openings must not be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug or other similar surface.
This product should never be placed near or over a radiator or heat
register, or in a built-in installation unless proper ventilation is provided.
Never push objects of any kind into this product through cabinet slots as
they may touch dangerous voltage points or short-out parts that could
result in a fire or electric shock. Never spill liquid of any kind onto or into
the product.
To avoid damage of internal components and to prevent battery leakage,
do not place the product on a vibrating surface.
iv
•
Never use it under sporting, exercising, or any vibrating environment
which will probably cause unexpected short current or damage rotor
devices, lamp.
Using electrical power
•
•
•
•
•
This product should be operated from the type of power indicated on the
marking label. If you are not sure of the type of power available, consult
your dealer or local power company.
Do not allow anything to rest on the power cord. Do not locate this
product where people will walk on the cord.
If an extension cord is used with this product, make sure that the total ampere
rating of the equipment plugged into the extension cord does not exceed the
extension cord ampere rating. Also, make sure that the total rating of all
products plugged into the wall outlet does not exceed the fuse rating.
Do not overload a power outlet, strip or receptacle by plugging in too
many devices. The overall system load must not exceed 80% of the branch
circuit rating. If power strips are used, the load should not exceed 80% of
the power strip's input rating.
This product's AC adapter is equipped with a three-wire grounded plug.
The plug only fits in a grounded power outlet. Make sure the power outlet
is properly grounded before inserting the AC adapter plug. Do not insert
the plug into a non-grounded power outlet. Contact your electrician for
details.
Warning! The grounding pin is a safety feature. Using a power outlet that is
not properly grounded may result in electric shock and/or injury.
Note: The grounding pin also provides good protection from unexpected
noise produced by other nearby electrical devices that may interfere with
the performance of this product.
•
Use the product only with the supplied power supply cord set. If you need
to replace the power cord set, make sure that the new power cord meets
the following requirements: detachable type, UL listed/CSA certified, VDE
approved or its equivalent, 4.5 meters (15 feet) maximum length.
Product servicing
Do not attempt to service this product yourself, as opening or removing covers
may expose you to dangerous voltage points or other risks. Refer all servicing to
qualified service personnel.
Unplug this product from the wall outlet and refer servicing to qualified service
personnel when:
•
the power cord or plug is damaged, cut or frayed
v
•
•
•
•
•
liquid was spilled into the product
the product was exposed to rain or water
the product has been dropped or the case has been damaged
the product exhibits a distinct change in performance, indicating a need
for service
the product does not operate normally after following the operating
instructions
Note: Adjust only those controls that are covered by the operating
instructions, since improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to
restore the product to normal condition.
Warning! For safety reasons, do not use non-compliant parts when adding
or changing components. Consult your reseller for purchase options.
Your device and its enhancements may contain small parts. Keep them out of
the reach of small children.
Additional safety information
•
•
•
Do not look into the projector's lens when the lamp is on. The bright may
hurt your eyes.
Turn on the projector first and then signal sources
Do not place the product in following environments:
•
•
•
•
•
•
•
•
•
•
•
Space that is poorly ventilated or confined. At least 50cm clearance from walls
and free flow of air around the projector is necessary.
Locations where temperatures may become excessively high, such as inside of a
car with all windows rolled up.
Locations where excessive humidity, dust, or cigarette smoke may contaminate
optical components, shortening the life span and darkening the image.
Locations near fire alarms.
Locations with an ambient temperature above 40 ºC/104 ºF.
Locations where the altitudes are higher than 10000 feet.
Unplug immediately if there is something wrong with your projector. Do
not operate if smoke, strange noise or odor comes out of your projector. It
might cause fire or electric shock. In this case, unplug immediately and
contact your dealer.
Do not keep using this product to break or drop it. In this case contact your
dealer for inspection.
Do not face the projector lens to the sun. It can lead to fire.
When switching the projector off, suggest to ensure the projector
completes its cooling cycle before disconnecting power.
Do not frequently turn off the main power abruptly or unplug the
projector during operation. The best way is to wait for the fan to turn off
before turning main power off.
vi
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Do not touch air outlet grille and bottom plate which becomes hot.
Clean the air filter frequently if have. The temperature inside may rise and
cause damage when the filter/ventilation slots clogged with dirt or dust.
Do not look into the air outlet grille when projector is operating. It may
hurt your eyes.
Always open the lens shutter or remove the lens cap when the projector is
on.
Do not block the projector lens with any object when the projector is
under operation as this could cause the object to become heated and
deformed or even cause a fire.
The lamp becomes extremely hot during operation. Allow the projector to
cool for approximately 45 minutes prior to removing the lamp assembly for
replacement.
Do not operate lamps beyond the rated lamp life. It could cause it to break
on rare occasions.
Never replace the lamp assembly or any electronic components unless the
projector is unplugged.
The product will detect the life of the lamp itself. Please be sure to change
the lamp when is showing warning message.
When changing the lamp, please allow unit to cool down, and follow all
changing instructions.
Reset the "Lamp Reset" function from the Onscreen display "OPTIONS |
Lamp Settings" menu after replacing the lamp module.
Do not attempt to disassemble this projector. There are dangerous high
voltages inside which may hurt you. The only user serviceable part is the
lamp which has its own removable cover. Refer servicing only to suitable
qualified professional service personnel.
Do not stand the projector on end vertically. It may cause the projector to
fall over, causing injury or damage.
This product is capable of displaying inverted images for ceiling mount
installation. Only use acer ceiling mount kit for mounting the projector
and ensure it is securely installed.
The projector should be placed in a horizontal way by means of desktop or
ceiling mount mode only, and its tilt angles should not exceed 3.8 degrees,
otherwise it would cause dramatical decrease of lamp life or severe safety
concern of system malfunction.
3.8°
3.8°
vii
Caution for Listening
To protect your hearing, follow these instructions.
•
•
•
•
•
Increase the volume gradually until you can hear clearly and comfortably.
Do not increase the volume level after your ears have adjusted.
Do not listen to music at high volumes for extended periods.
Do not increase the volume to block out noisy surroundings.
Decrease the volume if you can't hear people speaking near you.
Disposal instructions
Do not throw this electronic device into the trash when discarding. To minimize
pollution and ensure utmost protection of the global environment, please
recycle. For more information on the Waste from Electrical and Electronics
Equipment (WEEE) regulations, visit
http://www.acer-group.com/public/Sustainability/sustainability01.htm
Mercury advisory
For projectors or electronic products containing an LCD/CRT monitor or display:
“Lamp(s) contain Mercury,
Dispose Properly.”
Lamp(s) inside this product contain mercury and must be recycled or disposed of
according to local, state or federal laws. For more information, contact the
Electronic Industries Alliance at www.eiae.org. For lamp-specific disposal
information, check www.lamprecycle.org
viii
First things first
Usage Notes
Do:
•
Turn off the product before cleaning.
•
Use a soft cloth moistened with mild detergent to clean the display
housing.
•
Disconnect the power plug from AC outlet if the product is not being used
for a long period of time.
Don't:
•
Block the slots and openings on the unit provided for ventilation.
•
Use abrasive cleaners, waxes or solvents to clean the unit.
•
Use under the following conditions:
•
•
•
•
In extremely hot, cold or humid environments.
In areas susceptible to excessive dust and dirt.
Near any appliance that generates a strong magnetic field.
Place In direct sunlight.
Precautions
Follow all warnings, precautions and maintenance as recommended in this
user's guide to maximize the life of your unit.
Warning:
•
•
Do not look into the projector's lens when the lamp is on. The bright light may hurt
your eyes.
To reduce the risk of fire or electric shock, do not expose this product to rain or
moisture.
•
•
Please do not open or disassemble the product as this may cause electric shock.
•
This product will detect the life of the lamp itself. Please be sure to change the lamp
when it shows warning messages.
•
Reset the "Lamp Reset" function from the Onscreen display "OPTIONS | Lamp
Settings" menu after replacing the lamp module.
•
When switching the projector off, please ensure the projector completes its cooling
cycle before disconnecting power.
•
•
•
Turn on the projector first and then the signal sources.
When changing the lamp, please allow unit to cool down, and follow all changing
instructions.
Do not use lens cap when projector is in operation.
When the lamp reaches the end of its life, it will burn out and may make a loud
popping sound. If this happens, the projector will not turn back on until the lamp
module has been replaced. To replace the lamp, follow the procedures listed under
"Replacing the Lamp".
Table of Contents
Table of Contents.............................1
Introduction.......................................2
Package Overview...............................2
Product Overview................................3
Main Unit............................................... 3
Control Panel........................................ 4
Input/Output Connections..................... 5
Remote Control..................................... 6
Installation........................................7
Connecting to the Projector.................7
Connecting a Computer/Notebook....... 7
Connecting a Video source................... 8
Connect to 3D Video Devices..............9
Using the 3D glasses.........................11
Powering On/Off the Projector...........12
Powering On the Projector.................. 12
Powering Off the Projector................. 13
Warning Indicator................................ 14
Adjusting the Projected Image...........15
Adjusting the Projector’s Height ........ 15
Adjusting the Projector’s Focus.......... 16
Adjusting Projection Image Size......... 16
SETUP | Advanced............................. 62
OPTIONS............................................ 63
OPTIONS | Lamp Settings.................. 67
OPTIONS | Advanced......................... 69
OPTIONS | Remote Settings.............. 71
OPTIONS | Filter Settings................... 72
OPTIONS | Filter Settings................... 73
Appendices.....................................74
Troubleshooting.................................74
Image Problems.................................. 74
Other Problems................................... 76
Remote Control Problems.................. 76
LED Lighting Messages...................... 77
On Screen Messages......................... 78
Replacing the Lamp...........................79
Installing and Cleaning the
Dust Filter..........................................81
Compatibility Modes..........................82
Ceiling Mount Installation...................84
Regulations and safety notices..........85
User Controls.................................19
Control Panel & Remote Control.......19
Control Panel...................................... 19
Remote Control................................... 20
On-screen Display Menus.................23
How to operate................................... 23
IMAGE................................................ 24
IMAGE | Advanced............................. 27
DISPLAY............................................. 32
DISPLAY | 3D .................................... 37
SETUP................................................ 39
SETUP | Audio Settings...................... 42
SETUP | Security................................ 44
SETUP | Network................................ 46
SETUP | Network| LAN Settings......... 47
SETUP | Network| Control Settings.... 49
SETUP | Signal (RGB)........................ 59
SETUP | Signal (Video)...................... 61
1
English
Introduction
Package Overview
Unpack and inspect the box contents to ensure all parts listed
below are in the box. If something is missing, please contact
Acer customer service.
Standard Accessories
Power
Switch
Freeze
L
R
Enter
Laser
Page-
Keystone
-
Page+
Volume
-
+
1
2
Menu
4
5
HDMI
VGA
+
3
3D
6
Video
7
8
9
User1
User2
User3
0
Source
Projector
Power Cord
Resync
Remote
CD User Manual

Warranty Card

Quick Start Guide

VGA Cable
English
2
2 × AAA Batteries
Documentation
Introduction
Product Overview
Main Unit
1
3
2
4
6
5
™™ Do not block
projector in/out air
vents.
9
7
1.
2.
3.
4.
5.
Lamp Cover
Control Panel
Focus Switch
IR Receiver
Input/Output Connections
8
6.
7.
8.
9.
Lens
Power Socket
Speaker
IR Camera (Only for
interactive version)
3
English
Introduction
Control Panel
1
2
3
4
5
8
6
9
7
1.
2.
3.
4.
5.
6.
7.
8.
9.
English
4
ON/STANDBY LED
Enter
TEMP LED
LAMP LED
Menu
Input
Four Directional Select Keys
Power/Standby button
IR Receiver
Introduction
Input/Output Connections
7
8
9
VGA IN 2 / VGA OUT
VGA IN 1
10
SERVICE
11
HDMI 2
DC 12V OUT
RS-232
6
HDMI 1
VIDEO
3D SYNC
5
12
4
13
AUDIO IN 2
14
R-AUDIO IN 1-L
15 16
MICROPHONE AUDIO OUT
AC POWER
LAN
3
2
1
1.
2.
3.
4.
5.
6.
7.
™™ Remote mouse
requires special
remote.
Power Socket
KensingtonTM Lock Port
RJ45 Connector
3D Sync Connector (5V)
RS-232C Connector (9-pin DIN Type)
12V Out Connector
USB Connector (Connect to PC for Remote Mouse
function)
8. VGA-Out/VGA2-In Connector
9. VGA1-In/YPbPr Connector (PC Analog Signal/Component
Video Input/HDTV/YPbPr)
10. Composite Video Input Connector
11. HDMI2 Input Connector
12. HDMI1 Input Connector
13. Audio 2 In Connector (3.5mm mini Jack)
14. Composite Audio Input (right/left) Connector
15. Audio Input Connector (microphone)
16. Audio Output Connector (3.5mm mini Jack)
5
English
Introduction
Remote Control
™™ Some keys may
have no function
for models which
do not support
these features.
1
Power
Switch
16
2
Freeze
3
4
17
L
R
18
5
19
Enter
6
7
8
9
10
11
12
13
14
15
English
6
Laser
Page-
Keystone
-
-
+
1
Page+
+
2
3
Menu
3D
4
5
6
HDMI
VGA
Video
7
8
9
User1
User2
User3
21
22
23
24
25
26
0
Source
20
Volume
Resync
27
1. Power on / off
2. Freeze
3. Display blank /
audio mute
4. Mouse left click
5. Enter
6. Laser
7. Page 8. Keystone - / +
9. Menu
10. Aspect ratio
11. HDMI
12. User 2
13. User 1
14. Source
15. Brightness mode
16. Mouse on / off
17. Mute
18. Mouse right click
19. Four directional
select keys
20. Page +
21. Volume - / +
22. 3D menu on / off
23. VGA
24. Video
25. User 3
26. Numeric keypad
(0-9)
27. Re-sync
Installation
Connecting to the Projector
Connecting a Computer/Notebook
MOLEX
1
2
3
5
4
8
Microphone input
VGA IN 2 / VGAA OUT
UT
RS-232
™™ Due to the
difference in
applications for
each country,
some regions may
have different
accessories.
™™ (*) Optional
accessory
VGA IN 1
HDMI 1
VIDEO
3D SYNC
R-AUDIO IN 1-L
MICROPHONE AUDIO OUT
AC POWER
Audio output
11
3D glasses
AUDIO IN 2
LAN
E62405SP
HDMI 2
R
6
SERVICE
7
10
9
1��������������������������������������������������������������������������������������������*RS-232C cable
2.�������������������������������������������������������������������������*Remote Mouse USB cable
3.����������������������������������������������������������������������������������VGA1-In/YPbPr cable
4.�������������������������������������������������������������������������������������������������*HDMI cable
5.����������������������������������������������������������������������������������������� *Audio 2 In cable
6����������������������������������������������������������������������������������������������������Power cord
7�������������������������������������������������������������������������������������������*Audio Out cable
8������������������������������������������������������������������������������������*Microphone In cable
9������������������������������������������������������������������������������������������������� *RJ-45 cable
10���������������������������������������������������������������������������������������� *3D emitter cable
11���������������������������������������������������������������������������� *VGA-Out/VGA2-In cable
7
English
Installation
Connecting a Video source
DVD player, Blu-ray player, Set-top box, HDTV
receiver, Games console
1
2
3
4
5
SERVICE
HDMI 2
VGA IN 1
VIDEO
AUDIO IN 2
R-AUDIO IN 1-L
MICROPHONE AUDIO OUT
AC POWER
R
VGA IN 2 / VGA OUT
HDMI 1
™™ Due to the
difference in
applications for
each country,
some regions may
have different
accessories.
™™ (*) Optional
accessory
RS-232
3D SYNC
LAN
E62405SP
DC 12V OUT
6
3D glasses
9
7
Audio output
8
DVD player, Set-top box,
HDTV receiver
1�����������������������������������������������������������������������������*3 RCA Component cable
2.�������������������������������������������������������������������������������������������������*HDMI cable
3.������������������������������������������������������������������������������������������ *Audio2 In cable
4.�������������������������������������������������������������������������������������������� *Audio In cable
5.���������������������������������������������������������������������������������������������������Power cord
6�������������������������������������������������������������������������������������������*Audio Out cable
7������������������������������������������������������������������������������������*Microphone In cable
8��������������������������������������������������������������������������������������������������*Video cable
9������������������������������������������������������������������������������������������ *3D emitter cable
English
8
Installation
Connect to 3D Video Devices
™™ The 3D video
source device
must be
powered on
before the 3D
projector.
™™ If input video
is normal 2D,
please press
“3D Format”
and switch to
“Auto”.
™™ If “SBS” is
active, 2D
video content
will not display
correctly.
Once you have connected your devices together with HDMI
cables, as shown in the diagram, you are ready to begin.
Power ON your 3D video source and your 3D projector.
PlayStation® 3 Games
yy Make sure that you have updated your console to the latest
software version.
yy Go to the “Settings menu -> Display settings -> Video output ->
HDMI”. Select “Automatic” and follow the on-screen instructions.
yy Insert your 3D game disc. Alternatively you can download games
(and 3D updates) via the PlayStation® network.
yy Launch the game. In the in-game menu, select “Play in 3D”.
Blu-ray 3D™ Player
yy Make sure that your player can support 3D Blu-ray™ disc and that
3D output is enabled.
yy Insert the 3D Blu-ray™ disc into the player, press “Play”.
3D TV (e.g. SKY 3D, DirecTV)
yy Contact your TV service provider to enable any 3D channels on
your channel package.
yy Once enabled, switch to the 3D channel.
yy You should see two images side-by-side.
yy Switch to the “SBS” of the 3D projector. The option is located in
the “DISPLAY” section of the projector OSD menu.
3D Device (e.g. 3D DV/DC) with 2D 1080i side by side signal
output
yy Connect your 3D device and switch to out 3D content with 2D
side-by-side output to 3D Projector.
-- You should see two images side-by-side.
yy Switch to the “SBS” of the 3D projector. The option is located in
the “DISPLAY” section of the projector OSD menu.
If watching 3D content from an HDMI 1.4a source (e.g. 3D Blu-ray)
your 3D glasses should always be in sync. If watching 3D content
from an HDMI 1.3 source (e.g. 3D broadcast using SBS mode) it may
be necessary to use the projector’s 3D Sync-Invert option to optimize
your 3D experience. The option is located in the “DISPLAY ->3D”
section of the projector OSD menu.
9
English
Installation
3D Broadcast
3D Blu-ray™ Disc
SKY+HD, cable/satellite
box
3D Blu-ray™ Player
3D Console Games
PlayStation® 3
3D DLP®Link™ Glasses
Full 3D 1080p DLP® Projector
3D RF Glasses
English
10
3D Emitter
Installation
Using the 3D glasses
™™ For more
detailed
information,
please refer
to 3D glasses
user’s guide.
1. To turn ON 3D glasses.
2. Verify that 3D content is being sent to the projector and
signal is compatible with projector specifications.
3. Turn on the “3D Mode” (Off/ DLP-Link/ VESA 3D depending on which type of glasses you are using) of the
3D projector. The option is located in the “3D” section of the
projector OSD menu.
4. Turn on 3D glasses and verify image appears in 3D without
eyestrain.
5. If the image does not appear in 3D, please check 3D
device set up correctly to send out 3D image or not. Or
“SBS” should turn on when input signal is 2D 1080i sideby-side and repeat previous steps 1 ~ 4.
6. It may be necessary to use projector’s “3D Sync. Invert”
option to optimize your 3D experience. The option is
located in the “3D” section of the projector OSD menu.
7. To turn OFF 3D glasses: Press the “Power” button and hold
until the LED switches off.
8. For more detailed information, please refer to the 3D
glasses user’s guide, or manufacturer's Website.
11
English
Installation
Powering On/Off the Projector
Powering On the Projector
1. Securely connect the power cord and signal cable. When
connected, the On/Standby LED will turn Red.
2. Turn on the lamp by pressing “ ” button either on the top of
the projector or on the remote. The On/Standby LED will now
turn Blue.
The startup screen will display in approximately 10 seconds.
The first time you use the projector, you will be asked to
select the preferred language and power saving mode.
3. Turn on and connect the source that you want to display
on the screen (computer, notebook, video player, etc). The
projector will detect the source automatically. If not, push
menu button and go to “OPTIONS”.
Make sure that the “Source Lock” has been set to “Off”.
If you connect multiple sources at the same time, press the
“Source” button on the Remote Control or direct source keys
on the remote control to switch between inputs.
™™ Turn on the
projector first and
then select the
signal sources.
™™ (*) Optional
accessory.
or
Power
Switch
Freeze
L
R
Enter
Laser
Page-
Keystone
-
English
12
-
+
1
Page+
Volume
+
2
3
Menu
3D
4
5
6
HDMI
VGA
Video
7
8
9
User1
User2
User3
0
Source
Resync
Installation
Powering Off the Projector
1. Press the “ ” button on the remote control or on the
Control Panel to turn off the projector. The following
message will be displayed on the screen.
Power Off?
Press Power again
Press the “ ” button again to confirm otherwise the
message will disappear after 15 seconds. When you press
the “ ” button for the second time, the projector will shut
down.
2. The cooling fans continue to operate for about 10 seconds
for cooling cycle and the On/Standby LED will flash Blue.
When the On/Standby LED lights solid Red, the projector
has entered standby mode.
If you wish to turn the projector back on, you must wait
until the projector has completed the cooling cycle and
has entered standby mode. Once in standby mode, simply
press “ ” button to restart the projector.
3. Disconnect the power cord from the electrical outlet and the
projector.
4. Do not turn on the projector immediately following a power
off procedure.
13
English
Installation
Warning Indicator
™™ Contact the
nearest service
center if the
projector displays
these symptoms.
English
14
When the warning indicators (see below) come on,
the projector will automatically shutdown:
 “LAMP” LED indicator is lit red and if “On/Standby” indicator
flashes red.
 “TEMP” LED indicator is lit red and if “On/Standby”
indicator flashes red. This indicates the projector has
overheated. Under normal conditions, the projector can be
switched back on.
 “TEMP” LED indicator flashes red and if
“On/Standby” indicator flashes red.
Unplug the power cord from the projector, wait for 30 seconds
and try again. If the warning indicator light up again, please
contact your nearest service center for assistance.
Installation
Adjusting the Projected Image
Adjusting the Projector’s Height
The projector is equipped with elevator feet for adjusting
the image height.
1.Locate the adjustable foot you wish to modify on the
underside of the projector.
2. Rotate the adjustable ring clockwise to raise the projector
or counter clockwise to lower it. Repeat with the remaining
feet as needed.
Tilt-Adjustment Feet
Tilt-Adjustment Ring
15
English
Installation
Adjusting the Projector’s Focus
To focus the image, slide the focus switch until the image is
clear.
Standard throw series (XGA): The projector will focus at
distances from 1.55 to 2.21 feet (0.47 to 0.68 meters)
counted from the center of lens.
Standard throw series (WXGA): The projector will focus
at distances from 1.59 to 2.15 feet (0.49 to 0.66 meters)
counted from the center of lens.
Standard throw series (1080p): The projector will focus
at distance from 1.46 to 1.83 feet (0.45 to 0.56 meters)
counted from the center of lens.
Focus Switch
Adjusting Projection Image Size
Projection Image Size (XGA) from 70”-100” (1.78 to 2.54
meters).
Projection Image Size (WXGA) from 85”-115” (2.16 to 2.92
meters).
Projection Image Size (1080p) from 80”-100” (2.03 to 2.54
meters).
English
16
Installation
Variables:
“a”: Image Offset (m) from the center of the lens to the top of the vertical image.
“b”: Distance from the center of the lens to the bottom of the projector.
“c”: Distance between the wall (projection surface) to the back of the projector.
“d”: Image Diagonal.
“g”: Distance between the center of the lens and wall (projection surface).
“m”: Distance between the wall (projection surface) and the front of the projector.
“p”: Distance from top of projector to the mounting hole.
“H”: Height of the Image.
“W”:Width of the image.
b
p
m
c
a
g
d
(H)
(W)
d
(H)
(W)
a
g
c
m
p
b
17
English
Installation
Standard throw XGA (4:3)
a
b
c
d
W
H
g
m
P
Distance
Image Offset
from the center
Distance from center
of the lens to the of lens to the bottom
top of the vertical
of projector (m)
image (m)
between
Distance between
the wall (projection
Image Diagonal
surface) to the back
(inch)
Width of Image Height of Image
Size
Size
the center
of lens and
wall(projection
of projector (m)
surface)
(inch)
(m)
(inch)
(m)
(feet)
(m)
Distance between
the wall(projection
Distance from
surface) and the
top of projector to
front of the projector mounting hole (m)
(m)
0.181
0.0631
0.219
70
56.0
1.42
42.0
1.07
1.55
0.47
0.253
0.115
0.192
0.0631
0.246
74
59.2
1.50
44.4
1.13
1.64
0.50
0.253
0.115
0.207
0.0631
0.287
80
64.0
1.63
48.0
1.22
1.77
0.54
0.253
0.115
0.233
0.0631
0.354
90
72.0
1.83
54.0
1.37
1.99
0.61
0.253
0.115
0.259
0.0631
0.422
100
80.0
2.03
60.0
1.52
2.21
0.68
0.253
0.115
m
P
Standard throw WXGA (16:10)
a
b
c
d
W
H
g
Distance
Image Offset
from the center
Distance from center
of the lens to the of lens to the bottom
top of the vertical
of projector (m)
image (m)
between
Distance between
the wall (projection
Image Diagonal
surface) to the back
(inch)
Width of Image Height of Image
Size
Size
the center
of lens and
wall(projection
of projector (m)
surface)
(inch)
(m)
(inch)
(m)
(feet)
(m)
Distance between
the wall(projection
Distance from
surface) and the
top of projector to
front of the projector mounting hole (m)
(m)
0.172
0.0631
0.232
85
72.1
1.83
45.0
1.14
1.59
0.49
0.253
0.115
0.176
0.0631
0.245
87
74.0
1.88
46.2
1.17
1.63
0.50
0.253
0.115
0.182
0.0631
0.261
90
76.4
1.94
47.7
1.21
1.69
0.51
0.253
0.115
0.202
0.0631
0.318
100
84.8
2.15
53.0
1.35
1.87
0.57
0.253
0.115
0.222
0.0631
0.375
110
93.3
2.37
58.3
1.48
2.06
0.63
0.253
0.115
0.232
0.0631
0.403
115
97.5
2.48
60.9
1.55
2.15
0.66
0.253
0.115
m
P
Standard throw 1080p (16:9)
a
b
c
d
W
H
g
Distance
Image Offset
from the center
Distance from center
of the lens to the of lens to the bottom
top of the vertical
of projector (m)
image (m)
between
Distance between
the wall (projection
Image Diagonal
surface) to the back
(inch)
Width of Image Height of Image
Size
of lens and
wall(projection
of projector (m)
surface)
(inch)
(m)
(inch)
(m)
(feet)
(m)
Distance between
the wall(projection
Distance from
surface) and the
top of projector to
front of the projector mounting hole (m)
(m)
0.179
0.0631
0.193
80
69.7
1.77
39.2
1.00
1.46
0.45
0.253
0.115
0.200
0.0631
0.244
89
77.6
1.97
43.7
1.11
1.63
0.50
0.253
0.115
0.202
0.0631
0.249
90
78.4
1.99
44.1
1.12
1.65
0.50
0.253
0.115
0.224
0.0631
0.305
100
87.2
2.21
49.0
1.25
1.83
0.56
0.253
0.115
These tables are for user’s reference only.
English
Size
the center
18
User Controls
Control Panel & Remote Control
Control Panel
Using the Control Panel
POWER
Refer to the “Power On/Off the Projector”
section on pages 12-13.
Enter
Confirm your item selection.
INPUT
Press “INPUT“ to select an input source.
MENU
Press “MENU“ to launch the on-screen display
(OSD) menu. To exit OSD, press “MENU“
again.
Four Directional
Select Keys
Use
to select items or make
adjustments to your selection.
LAMP LED
Indicate the projector’s lamp status.
TEMP LED
Indicate the projector’s temperature status.
ON/STANDBY
LED
Indicate the projector’s status.
19
English
User Controls
Remote Control
Using the Remote Control
Power
Switch
Freeze
L
R
Enter
Laser
Page-
Keystone
-
-
+
2
3
Menu
3D
4
5
6
HDMI
VGA
Video
7
8
9
User1
User2
User3
0
Source
English
Press to turn on / off the projector.
Switch
Press to switch the USB mouse on / off.
Display
blank/ audio
mute
Press to hide / unhide the screen picture
and turn off / on audio.
Freeze
Press to freeze the projector image.
Mute
Press to momentarily turn off / on the audio.
Volume
+
1
Page+
Power
Resync
20
Mouse left
click
L
Use as mouse left click.
Mouse right
click
R
Use as mouse right click.
Four
directional
select keys
Use
to select items or make
adjustments to your selection.
Enter
Confirm your item selection.
Page -
Press to page down.
Laser
Use as laser pointer.
Page +
Press to page up.
Keystone
-
+
Press to adjust image distortion caused by
tilting the projector.
Volume
-
+
Press to adjust to increase / decrease the
volume.
Aspect ratio
/1
`Press
`
to change aspect ratio of a
displayed image.
`Use
`
as numeric keypad number “1”.
Menu / 2
`Press
`
to display or exit the on-screen
display menus for projector.
`Use
`
as numeric keypad number “2”.
3D / 3
`Press
`
to manually select a 3D mode that
matches your 3D content.
`Use
`
as numeric keypad number “3”.
User Controls
Using the Remote Control
Power
Switch
HDMI / 4
`Press
`
to choose HDMI source.
`Use
`
as numeric keypad number “4”.
VGA / 5
`Press
`
to choose VGA source.
`Use
`
as numeric keypad number “5”.
Video / 6
`Press
`
to choose composite video source.
`Use
`
as numeric keypad number “6”.
User1 / 7; User2 / 8;
User3 / 9
`User
`
defined keys.
`Use
`
as numeric keypad numbers “7”, “8”,
and “9” accordingly.
Source
Press to select an input signal.
Brightness
mode / 0
`Press
`
to automatically adjust the picture
brightness to give an optimum contrast
performance.
`Use
`
as numeric keypad number “0”.
Resync
Press to automatically synchronize the
projector to the input source.
Freeze
L
R
Enter
Laser
Page-
Keystone
-
-
+
1
Page+
Volume
+
2
3
Menu
3D
4
5
6
HDMI
VGA
Video
7
8
9
User1
User2
User3
0
Source
Resync
21
English
User Controls
Installing Batteries
Two size AAA batteries are supplied for Remote Control.
Replace only with the same or equivalent type recommended by the
manufacturer.
CAUTION
Improper use of batteries can result in chemical leakage or
explosion. Be sure to follow the instructions below.
Do not mix batteries of different types. Different types of batteries
have different characteristics.
Do not mix old and new batteries. Mixing old and new batteries can
shorten the life of new batteries or cause chemical leakage in old
batteries.
Remove batteries as soon as they are worn out. Chemicals that leak
from batteries that come in contact with skin can cause a rash. If you
find any chemical leakage, wipe thoroughly with a cloth.
The batteries supplied with this product may have a shorter life
expectancy due to storage conditions.
If you will not be using the remote control unit for an extended period
of time, remove batteries from it.
When you dispose of the battery, you must obey the law in the
relative area or country.
English
22
User Controls
On-screen Display Menus
The Projector has multilingual On-screen Display menus that
allow you to make image adjustments and change a variety of
settings. The projector will automatically detect the source.
How to operate
1. To open the OSD menu, press “Menu” on the Remote Control or
Control Panel.
2 When OSD is displayed, use
keys to select any item in the
main menu. While making a selection on a particular page, press
or “Enter” key to enter sub menu.
3.Use
keys to select the desired item in the sub menu and
then press
or “Enter” key to view further settings. Adjust the
settings by
key.
4. Select the next item to be adjusted in the sub menu and adjust as
described above.
5. Press “Enter” or “Menu” to confirm, and the screen will return to
the main menu.
6. To exit, press “Menu” again. The OSD menu will close and the
projector will automatically save the new settings.
Main Menu
™™ Some of the
following OSD
settings may not
be available.
Please refer to
the actual OSD of
your projector.
™™ Functions vary
depending on
model definition.
IMAGE
DIsplay Mode
Presentation
Brightness
Contrast
Sub Menu
Settings
Sharpness
Color
Tint
Advanced
23
English
User Controls
IMAGE
IMAGE
DIsplay Mode
Presentation
Brightness
Contrast
Sharpness
Color
Tint
Advanced
DIsplay Mode
There are many factory presets optimized for various types of
images.
`` Presentation: This mode is suitable for showing in front of
public in connection to the PC.
`` Bright: Maximum brightness from PC input.
`` Movie: This mode is suitable for watching video.
`` User: Memorize user’s settings.
`` Blackboard: This mode should be selected to achieve optimum
color settings when projecting onto a blackboard (green).
`` DICOM SIM.: This mode can project a monochrome medical
image such as an X ray radiography, MRI, etc.
`` Standard Mode: Standardized accurate color.
`` 3D: To experience the 3D effect, you need to have 3D glasses,
make sure your PC/portable device has a 120 Hz signal output
quad buffered graphics card and have a 3D Player installed.
English
24
User Controls
Presentation
Bright
Movie
User
Blackboard
DICOM SIM.
Standard Mode
3D
User
Brightness
Adjust the brightness of the image.
`` Press the
to darken image.
`` Press the
to lighten the image.
Brightness
Contrast
The contrast controls the degree of difference between the lightest
and darkest parts of the picture.
`` Press the
to decrease the contrast.
`` Press the
to increase the contrast.
Contrast
25
English
User Controls
Sharpness
Adjust the sharpness of the image.
`` Press the
to decrease the sharpness.
`` Press the
to increase the sharpness.
Sharpness
Color
Adjust a video image from black and white to fully saturated color.
`` Press the
to decrease the amount of saturation in the
image.
`` Press the
to increase the amount of saturation in the
image.
Color
Tint
Adjust the color balance of red and green.
`` Press the
to increase the amount of green in the image.
`` Press the
to increase the amount of red in the image.
Tint
Reset
Choose “Yes” to return the factory default settings for “IMAGE”.
Exit
Choose “Exit” to exit the menu.
English
26
User Controls
IMAGE
IMAGE | Advanced
Advanced
Noise Reduction
Gamma
Film
Brilliant Color
RGB Gain/Bias
Color Temp.
Cool
Color Matching
Color Space
Auto
Exit
Noise Reduction
Selects a filter sensitivity to noise. A higher value may improve
noisy sources, but it will soften the image.
`` Press the
`` Press the
to decrease the noise in the image.
to increase the noise in the image.
Noise Reduction
Gamma
This allows you to set up gamma curve type. After the initial setup
and fine tuning is completed, utilize the Gamma Adjustment steps
to optimize your image output.
`` Film: for home theater.
`` Graphic: for PC / Photo source.
`` Blackboard: This mode should be selected to achieve optimum
color settings when projecting onto a blackboard (green).
`` DICOM SIM.: This mode can project a monochrome medical
image such as an X ray radiography, MRI, etc.
`` 1.8/2.0/2.2/2.6: For specific PC / Photo source.
`` 3D: for 3D mode.
Press the
or
to select the mode.
Gamma
Film
27
English
User Controls
Brilliant Color™
This adjustable item utilizes a new color-processing algorithm and
enhancements to enable higher brightness while providing true,
more vibrant colors in picture.
`` Press the
`` Press the
to stronger enhance the image.
to less enhance the image.
Brilliant Color
RGB Gain/Bias
This settings allows to configure the brightness (gain) and contrast
(bias) of an image.
`` Press the
to decrease a chosen color gain and bias.
`` Press the
to increase a chosen color gain and bias.
RGB Gain/Bias
Red Gain
Green Gain
Blue Gain
Red Bias
Green Bias
Blue Bias
Reset
Color Temp.
Press the
or
Cool and Cold.
Exit
to select a color temperature from Standard,
Color Temp.
Cool
English
28
User Controls
Color Matching
Press the
into the next menu and then use
to select the item.
or
or
or
Color Matching
Red
Cyan
Green
Magenta
Blue
Yellow
White
Reset
Exit
`` Red: Press the
or
Colors. Then press the
value respectively.
to select Hue, Saturation and Gain
or
to decrease or increase the
Red
Hue
Saturation
Gain
Exit
`` Cyan: Press the
or
Colors. Then press the
value respectively.
to select Hue, Saturation and Gain
or
to decrease or increase the
Cyan
Hue
Saturation
Gain
Exit
29
English
User Controls
`` Green: Press the
or
Colors. Then press the
value respectively.
to select Hue, Saturation and Gain
or
to decrease or increase the
Green
Hue
Saturation
Gain
Exit
`` Magenta: Press the
or
to select Hue, Saturation and
Gain Colors. Then press the
or
to decrease or increase
the value respectively.
Magenta
Hue
Saturation
Gain
Exit
`` Blue: Press the
or
Colors. Then press the
value respectively.
to select Hue, Saturation and Gain
or
to decrease or increase the
Blue
Hue
Saturation
Gain
Exit
`` Yellow: Press the
or
Colors. Then press the
value respectively.
to select Hue, Saturation and Gain
or
to decrease or increase the
Yellow
Hue
Saturation
Gain
Exit
English
30
User Controls
`` White: Press the
or
Colors. Then press the
value respectively.
to select Hue, Saturation and Gain
or
to decrease or increase the
White
Red
Green
Blue
Exit
`` Reset: Choose “ Reset” to return the factory default settings
for color adjustments.
Color Space
Press the
or
to select an appropriate color matrix type from
the following:
`` Non-HDMI Input: Auto, RGB or YUV
`` HDMI Input: Auto, RGB(0-255), RGB(16-235) or YUV.
Color Space
Auto
Exit
Choose “Exit” to exit the menu.
31
English
User Controls
DISPLAY
Format
DISPLAY
Zoom
Edge Mask
Image Shift
V. Keystone
Exit
Format
Press the
or
to choose your desired aspect ratio between
4:3, 16:9/16:10 (WXGA), LBX, Native, and Auto.
Format
XGA
`` 4:3: This format is for 4:3 input sources.
`` 16:9: This format is for 16:9 input sources, like HDTV and DVD
enhanced for Wide screen TV.
`` Native: This format displays the original image without any
scaling.
`` Auto: Automatically selects the appropriate display format.
Source
4:3
Scale to 1024 x 768
Scale to 1024 x 576
Auto
32
576i/p
16:9
Native
English
480i/p
1080i/p
720p
No scaling will be made; the resolution is dependent on
which input source and is then displayed.
``If source is 4:3, it will be auto resized to 1024 x 768
``If source is 16:9, it will be auto resized to 1024 x 576
``If source is 15:9, it will be auto resized to 1024 x 614
``If the source is 16:10, it will be auto resized to 1024 x 640
User Controls
WXGA
`` 4:3: This format is for 4:3 input sources.
`` 16:9: This format is for 16:9 input sources, like HDTV and DVD
enhanced for Wide screen TV.
`` 16:10: This format is for 16:10 input sources, like widescreen
laptops.
`` LBX: This format is for non-16x9, letterbox source and for
users who use external 16x9 lens to display 2.35:1 aspect
ratio using full resolution.
`` Native: This format displays the original image without any
scaling.
`` Auto: Automatically selects the appropriate display format. 
Detail informations about LBX mode:
1. Some Letter-Box Format DVDs are not enhanced for 16x9
TVs. In this situation, the image will not look right when
displayed in 16:9 mode. In this situation, please try to using
the 4:3 mode to view the DVD. If the content is not 4:3, there
will be black bars around the image in 16:9 display. For this
type of content, you can use LBX mode to fill the image on the
16:9 display.
2. If you use an external anamorphic lens, this LBX mode also
allows you to watch a 2.35:1 content (include Anamorphic
DVD and HDTV film source) that support anamorphic wide
is enhanced for 16x9 Display in a wide 2.35:1 image. In
this case, there are no black bars. Lamp power and vertical
resolution are fully utilized.
16:9 Screen
480i/p
576i/p
1080i/p
720p
PC
4:3
Scale to 960 x 720
16:9
Scale to 1280 x 720
LBX
Scale to 1280 x 960, in order to get the central 1280 x 720
image displayed on the screen.
Native
Auto
1:1 mapping
centered
1:1
mapping
display
1280 x 720
1280 x 720
centered
1:1 mapping
centered
``If this format is selected, the screen type will
automatically set to 16:9 (1280 x 720)
``If source is 4:3, it will be auto resized to 960 x 720
``If source is 16:9, it will be auto resized to 1280 x 720
``If source is 15:9, it will be auto resized to 1200 x 720
``If the source is 16:10, it will be auto resized to 1152 x 720
33
English
User Controls
16:10 Screen
480i/p
576i/p
1080i/p
4:3
Scale to 1066 x 800
16:10
Scale to 1280 x 800
720p
PC
Scale to 1280 x 960, in order to get the central 1280 x 800
image displayed on the screen.
LBX
Native
1:1 mapping
centered
1:1
mapping
display
1280 x 800
1280 x 720
centered
1:1 mapping
centered
``Input source will be fit into 1280x800 display area and be
kept its original aspect ratio
``If source is 4:3, auto resize to 1066 x 800
``If source is 16:9 auto resize to 1280 x 720
``If source is 15:9 auto resize to 1280 x 768
``If source is 16:10 auto resize to 1280 x 800
Auto
1080P
`` 4:3: This format is for 4:3 input sources.
`` 16:10: This format is for 16:10 input sources, like widescreen
laptops.
`` LBX: This format is for non-16x9, letterbox source and for
users who use external 16x9 lens to display 2.35:1 aspect
ratio using full resolution.
`` Native: This format displays the original image without any
scaling.
`` Auto: Automatically selects the appropriate display format.
16:9 Screen
34
576i/p
4:3
Scale to 1440 x1080
16:10
Scale to 1920x1080
1080i/p
720p
PC
LBX
Scale to 1920 x 1440, in order to get the central 1920 x
1080 image displayed on the screen.
Native
1:1 mapping centered
No scaling will be made; the resolution is dependent on
which input source and is then displayed.
Auto
English
480i/p
``If this format is selected, the screen type will automatically
become 16:9
``If source is 4:3, auto resize to 1440 x 1080
``If source is 16:9 auto resize to 1920 x 1080
``If source is 16:10 auto resize to 1920 x 1200 and cut to
1920 x x1080 area display
User Controls
Zoom
`` Press the
`` Press the
to reduce the size of an image.
to magnify an image on the projection screen.
Zoom
Edge Mask
Edge mask the image to remove video encoding noise on the
edge of video source.
`` Press the
`` Press the
to decrease the edge mask in image.
to increase the edge mask in image.
Edge Mask
Image Shift
™™ Each I/O has
different setting of
“Edge Mask”.
™™ “Edge Mask” and
“Zoom” can’t work
at same time.
Press the
into the next menu as below and then press the
or
or
or
to select item.
Image Shift
Image Shift
H: 10
Image Shift
Image Shift
H: 0
`` H: Press the
horizontally.
`` V: Press the
vertically.
V: -10
V: -10
to shift the projected image position
to shift the projected image position
35
English
User Controls
V. Keystone
Press the
or
a squarer image.
to adjust image distortion vertically and make
V. Keystone
Exit
Choose “Exit” to exit the menu.
English
36
User Controls
DISPLAY
3D
DISPLAY | 3D
DLP-Link
3D Mode
3D->2D
3D Format
3D
Frame Sequential
3D Sync. Invert
Off
Exit
3D Mode
`` Off: Select “Off” to turn off 3D mode.
`` Press the
or
to select the 3D mode.
3D Mode
™™ 3D Format is only
supported on 3D
Timing on page
82.
™™ “3D Format” is
only supported on
non-HDMI 1.4a 3D
timing.
DLP-Link
`` DLP-Link: Select “DLP-Link” to use optimized settings for DLP
Link 3D Glasses. (refer to page 11).
`` VESA 3D: Select “VESA 3D” to use optimized setting for VESA
3D Glasses. (refer to page 11).
3D->2D
`` Press the
or
to select 3D -> 2D.
3D->2D
3D
`` 3D: Display 3D signal.
`` L (Left): Display the left frame of 3D content.
`` R (Right): Display the right frame of 3D content.
37
English
User Controls
3D Format
`` Press the
or
to select 3D format.
3D Format
Frame Sequential
`` Auto: When a 3D identification signal is detected, the 3D
format is selected automatically.
`` SBS: Display 3D signal in “Side-by-Side” format.
`` Top and Bottom: Display 3D signal in “Top and Bottom” format.
`` Frame Sequential: Display 3D signal in “Frame Sequential”
format.
3D Sync. Invert
`` Press the
or
to select 3D sync. invert.
3D Sync. Invert
Off
On
`` Press the “On” to invert left and right frame contents.
`` Press the “Off” for default frame contents.
Exit
Choose “Exit” to exit the menu.
English
38
User Controls
SETUP
SETUP
Language
English
Projection
Menu Location
Audio Settings
Sceen Type
Security
Signal (RGB)
Advanced
Network
Exit
Signal (Video)
Advanced
Network
Exit
39
English
User Controls
Language
Choose the multilingual OSD menu. Press
into the sub menu
and then press the
or
or
or
key to select your preferred
language. Press “Enter” to finalize the selection.
Language
Exit
Projection
Press the
projection.
or
or
or
key to select the preferred
Projection
™™ Rear-Desktop and
Rear-Ceiling are
to be used with a
translucent screen.
Exit
``
Front-Projection
When selected, the image is projected straight on the screen.
``
Rear-Desktop
When selected, the image will appear reversed.
``
Front-Ceiling
This is the default selection. The image will turn upside down.
``
Rear-Ceiling
When selected, the image will appear reversed in upside down
position
English
40
User Controls
Menu Location
Press the
location.
or
or
or
key to select the preferred menu
Menu Location
Exit
Screen Type
Press the
™™ *This screen type
applies to WXGA
only.
or
to choose the screen type from16:10* or 16:9.
Screen Type
Exit
Choose “Exit” to exit the menu.
41
English
User Controls
SETUP
Audio Settings
SETUP |
Audio Settings
Internal Speaker
Off
Mute
Off
Volume
Audio Input
Default
Exit
Internal Speaker
Choose the “On” or “Off” to turn on or off the internal speaker.
™™ “Mute” function
affects both
internal and
external speaker
volume.
Internal Speaker
Off
On
Mute
`` Choose the “On” to turn mute on.
`` Choose the “Off” to turn mute off.
Mute
Off
Volume
`` Press the
`` Press the
On
to decrease the volume.
to increase the volume.
Volume
Audio
Mic
Exit
English
42
User Controls
Audio Input
The default audio settings are on the back panel of the projector.
Use this option to reassign any of the Audio Inputs (1 or 2) to the
current image source. Each Audio input can be assigned to more
than one video source.
`` Press
or
to select audio input.
Audio Input
Default
`` Default.
`` Audio 1: (RCA) for Composite
`` Audio 2: (Mini jack) for VGA
Exit
Choose “Exit” to exit the menu.
43
English
User Controls
SETUP
Security
SETUP | Security
Security
Off
Security Timer
Change Password
Exit
Security
`` On: Choose “On” to use security verification when the turning
on the projector.
`` Off: Choose “Off” to be able to switch on the projector without
password verification.
Security
Off
On
Security Timer
Can be select the time (Month/Day/Hour) function to set the
number of hours the projector can be used. Once this time has
elapsed you will be requested to enter your password again.
Press the
or
to set the month, day, and hour.
Security Timer
Month
Day
Hour
Exit
English
44
User Controls
Change Password
™™ Pass-code default
value is “1234” (first
time).
``
1.
2.
3.
Enter Security Code (4 digits)
REMOTE
First time:
Press “Enter” key to set the password.
The password has to be 4 digits.
Use number button on the remote or on-screen numeric
keypad to enter your new password and then press “Enter”
key to confirm your password.
`` Change Password:
(If your remote does not have a number keypad, please use
the up/down arrows to change each digit of the password,
then press enter to confirm)
1. Press “Enter” to input old password.
2. Use number button or on-screen numeric keypad to enter
current password and then press “Enter” to confirm.
3. Enter new password (4 digits in length) using the number
buttons on the remote, then press “Enter” to confirm.
4. Enter new password again and press “Enter” to confirm.
`` If the incorrect password is entered 3 times, the projector will
automatically shut down.
`` If you have forgotten your password, please contact your local
office for support.
Exit
Choose “Exit” to exit the menu.
45
English
User Controls
SETUP
Network
SETUP | Network
LAN Settings
Control Settings
Exit
LAN Settings
Loading network configuration
Please wait...
For more information on LAN Settings, refer to page 47-48,
and 51-58.
Control Settings
For more information on Control Settings, refer to page
49-58.
English
46
User Controls
SETUP
Network: LAN Settings
SETUP |
Network| LAN
Settings
Network Status
Connected
MAC Address
Off
DHCP
IP Address
Subnet Mask
Gateway
DNS
Apply
Exit
Network Status
Display the network connection status (read-only).
MAC Address
Display the MAC address (read-only).
DHCP
DHCP
Off
On
`` On: Projector will obtain an IP address automatically from your
network.
`` Off: To assign IP, Subnet Mask, Gateway and DNS
configuration manually.
Exiting OSD will automatically apply the entered values.
IP Address
IP Address
Display the IP address.
47
English
User Controls
Subnet Mask
Subnet Mask
Display subnet mask number.
Gateway
Gateway
Display the default gateway of the network connected to the
projector.
DNS
DNS
Display DNS number.
Apply
Press
and then choose “Yes” to apply the selection.
Apply
No
Exit
Choose “Exit” to exit the menu.
English
48
Yes
User Controls
SETUP
Network: Control Settings
SETUP |
Network| Control
Settings
Crestron
Off
Extron
Off
PJ Link
Off
AMX Device Discovery
Off
Telnet
Off
Exit
Crestron
Crestron
Off
On
Use this function to select the network function (port: 41794). For
more information, please visit http://www.crestron.com and
www.crestron.com/getroomview.
`` On: The Crestron function is active.
`` Off: The Crestron function is inactive.
Extron
Extron
Off
On
Use this function to select the network function (port: 2023).
`` On: The Extron function is active.
`` Off: The Extron function is inactive.
PJ Link
PJ Link
Off
On
Use this function to select the network function (port: 4352).
`` On: The PJ Link function is active.
`` Off: The PJ Link function is inactive.
49
English
User Controls
AMX Device Discovery
AMX Device Discovery
Off
On
Use this function to select the network function (port: 1023).
`` On: The AMX Discovery function is active.
`` Off: The AMX Discovery function is inactive.
Telnet
Telnet
Off
On
Use this function to select the network function (port: 23).
`` On: Telnet is enabled.
`` Off: Telnet is disabled.
Exit
Choose “Exit” to exit the menu.
English
50
User Controls
LAN_RJ45 Function
™™ Use Ethernet
Normal Cable
to connect the
projector to LAN.
For simplicity and ease of operation, the projector provides
diverse networking and remote management features.
The LAN/RJ45 function of the projector through a network, such
as remotely manage: Power On/Off, Brightness and Contrast
settings. Also, projector status information, such as: VideoSource, Sound-Mute, etc.
Projector
(Ethernet)
Wired LAN Terminal Functionalities
This projector can be controlled by using a PC (laptop) or other
external device via LAN/RJ45 port and compatible with Crestron/
Extron / AMX (Device Discovery) / PJLink.
`` Crestron is a registered trademark of Crestron Electronics, Inc.
of the United States.
`` Extron is a registered trademark of Extron Electronics, Inc. of
the United States.
`` AMX is a registered trademark of AMX LLC of the United
States.
`` PJLink applied for trademark and logo registration in Japan,
the United States of America, and other countries by JBMIA.
The projector is supported by the specified commands of the
Crestron Electronics controller and related software, for example
RoomView®.
http://www.crestron.com/
This projector is compliant to support Extron device(s) for
reference.
http://www.extron.com/
This projector is compliant to support Extron device(s) for
reference.
http://www.extron.com/
This projector is supported by AMX ( Device Discovery ).
http://www.amx.com/
51
English
User Controls
This projector supports all commands of PJLink Class1 (Version
1.00).
http://pjlink.jbmia.or.jp/english/
For more detailed information about the various types of external
devices which can be connected to the LAN/RJ45 port and
remote/control the project, as well as the supported commands
for these external devices, please contact the Support-Service
directly.
LAN RJ45
1. Connect an RJ45 cable to RJ45 ports on the projector and the
PC (laptop).
SERVICE
HDMI 2
VGA IN 2 / VGA OUT
DC 12V OUT
RS-232
VGA IN 1
3D SYNC
HDMI 1
VIDEO
AUDIO IN 2
R-AUDIO IN 1-L
MICROPHONE AUDIO OUT
AC POWER
LAN
2. On the PC (Laptop), select Start > Control Panel > Network
Connections.
English
52
User Controls
3. Right-click on the Local Area Connection, and select Property.
4. In the Properties window, select the General tab, and select
Internet Protocol (TCP/IP).
5. Click “Properties”.
53
English
User Controls
6. Type in the IP address and Subnet mask, then press “OK”.
7. Press the “Menu” button on the projector.
8. Use
keys to select SETUP > Network > LAN Settings.
9. After getting into LAN Settings, input the following connection
parameters:
`` DHCP: Off
`` IP Address: 10.10.10.10
`` Subnet Mask: 255.255.255.255
`` Gateway: 0.0.0.0
`` DNS: 0.0.0.0
10.Press “Enter” to confirm settings.
11.Open a web browser, for example Microsoft Internet Explorer.
with Adobe Flash Player 9.0 or higher installed.
12.In the Address bar, input the projector’s IP address:
10.10.10.10.
English
54
User Controls
13.Press “Enter”.
The projector is setup for remote management. The LAN/RJ45
function displays as follows:
Main Page
Information Page
55
English
User Controls
Tool Page
Contact IT Helpdesk
RS232 by Telnet Function
There is alternative RS232 command control way, in projector so
called “RS232 by TELNET” for LAN/RJ45 interface.
English
56
User Controls
Quick Start-Guide for “RS232 by Telnet”
`` Check and get the IP address on OSD of the projector.
`` Make sure that the PC/laptop can access the web-page of the
projector.
`` Make sure that "Windows FIrewall" setting is set disabled in
case of "TELNET" function filtering out by PC/laptop.
1. Start > All Programs.> Accessories > Command Prompt.
2. Input the command format as follows:
telnet ttt.xxx.yyy.zzz 23 (“Enter” key pressed)
(ttt.xxx.yyy.zzz: IP-Address of the projector)
3. If Telnet-Connection ready, and user can have RS232
command input, then “Enter” key pressed, the RS232
command will be workable.
57
English
User Controls
Specification for “RS232 by TELENT”:
™™ In Windows XP
built-in “TELNET.
exe” utility, “Enter”
key pressed will
have “CarriageReturn” and “NewLine” code.
English
58
1. Telnet: TCP.
2. Telnet port: 23 (for more detail, kindly please get contact with
the service agent or team).
3. Telnet utility: Windows “TELNET.exe” (console mode).
4. Disconnection for RS232-by-Telnet control normally: Close
5. Windows Telnet utility directly after TELNET connection ready.
`` Limitation 1 for Telnet-Control: there is less than 50
bytes for successive network payload for Telnet-Control
application.
`` Limitation 2 for Telnet-Control: there is less than 26 bytes
for one complete RS232 command for Telnet-Control.
`` Limitation 3 for Telnet-Control: Minimum delay for next
RS232 command must be more than 200 (ms).
User Controls
SETUP
Signal (RGB)
SETUP |
Signal (RGB)
Automatic
Disable
Phase
Frequency
H. Position
V. Position
Exit
Automatic
™™ “Signal” is only
supported in Analog
SETUP
VGA (RGB) signal.
Signal (RGB)
™™ If “Signal” is
Enable
Automatic
automatic, the
phase, frequency
Exit
items are grayed
out, and if “Signal”
Automatically selects the signal. If you use this function, the
is not automatic,
Phase, frequency items are grayed out, and if Signal is not
the phase,
automatic, the phase, frequency items will appear for user to
frequency items
manually tune and saved in settings after that for next time
will appear for the
projector turns off and on again
user to manually
tune and are saved Phase
in the settings after
that for the next
Phase
time projector is
turned off and on
again.
Synchronize the signal timing of the display with the graphic card.
If the image appears to be unstable or flickers, use this function to
correct it.
`` Press the
to decrease the phase value.
`` Press the
to increase the phase value.
59
English
User Controls
Frequency
Frequency
Change the display data frequency to match the frequency of
your computer’s graphic card. Use this function only if the image
appears to flicker vertically.
`` Press the
to decrease the frequency.
`` Press the
to increase the frequency.
H. Position (Horizontal Position)
H. Position
`` Press the
`` Press the
to move the image left.
to move the image right.
V. Position (Vertical Position)
V. Position
`` Press the
`` Press the
Exit
to move the image down.
to move the image up.
Choose “Exit” to exit the menu.
English
60
User Controls
SETUP
Signal (Video)
SETUP |
Signal (Video)
White Level
Black Level
Exit
White Level
White Level
Adjust the overall white level of the projected image by applying a
gain to the input image.
`` Press the
to decrease the white level.
`` Press the
to increase the white level.
Black Level
Black Level
Adjust the overall black level of the projected image by applying a
offset to the input image.
`` Press the
to decrease the black level.
`` Press the
to increase the black level.
Exit
Choose “Exit” to exit the menu.
61
English
User Controls
SETUP
Advanced
SETUP |
Advanced
Logo
Closed Captioning
Logo
Logo
Acer
Use this function to set the desired startup screen. If changes are
made they will take effect the next time the projector is powered
on.
`` Neutral: Logo is not displayed on startup screen.
`` Acer: Acer logo is displayed on startup screen.
Closed Captioning
Closed Captioning
Off
Closed Captioning is a text version of the program sound or other
information displayed on the screen. If the input signal contains
closed captions, you can turn on the feature and watch the
or
to select between CCI, or CC2. Choose
channels. Press
“Off” to disable this function.
Exit
Choose “Exit” to exit the menu.
English
62
User Controls
OPTIONS
Input Source
OPTIONS
Off
Source Lock
High Attitude
Off
Information Hide
Off
Off
Keypad Lock
Test Pattern
None
12V Trigger
On
Input Source
™™ “VGA 2” depends
on the settings of
“VGA2 Switch”.
Use this option to enable/disable input sources. Press ► to enter
the sub menu and select which sources you require. Press “Enter”
to finalize the selection. The projector will only search for inputs
that are enabled.
Input Source
Video
Exit
Source Lock
`` On: The projector will only search current input connection.
`` Off: The projector will search for other signals if the current
input signal is lost.
Source Lock
Off
On
High Attitude
When “On” is selected, the fans will spin faster. This feature is
useful in high altitude areas where the air is thin.
High Attitude
Off
On
63
English
User Controls
Information Hide
`` On: Choose “On” to hide the info message.
`` Off: Choose “Off” to show the “searching” message.
Information Hide
Off
On
Keypad Lock
When the keypad lock function is “On”, the Keypad will be locked
however, the projector can be operated by the remote control. By
selecting “Off”, you will be able to unlock the Keypad.
Keypad Lock
Off
On
Test Pattern
Display a test pattern. There are Grid, White Pattern and None.
Test Pattern
None
12V Trigger
`` Off: Choose “Off” to disable the trigger.
`` On: Choose “On” to enable the trigger.
12V Trigger
On
English
64
User Controls
OPTIONS
Background Color
OPTIONS
Black
VGA2 Switch
Out
Lamp Settings
Advanced
Filter Settings
Reset
Exit
Background Color
Use this feature to display a “Black”, “Red”, “Blue”, “Green” or
“White”, screen when no signal is available.
Background Color
White
VGA2 Switch
When the “VGA2 Switch” feature is “In” then VGA2 port functions
as input port. If the “VGA2 Switch” is “Out” then the port functions
as output port for VGA1.
VGA2 Switch
Out
In
65
English
User Controls
Reset
`` Current: Choose “Yes” to return the display parameters on this
menu to the factory default settings.
`` All: Choose “Yes” to return the display parameters on all
menus to the factory default settings.
Reset ?
No
Yes
Reset
Processing...
Exit
Choose “Exit” to exit the menu.
English
66
User Controls
OPTIONS
Lamp Settings
OPTIONS |
Lamp Settings
Lamp Hour
Lamp Reminder
Off
Dynamic
Brightness Mode
Lamp Reset
Exit
Lamp Hour
Display the projection time.
Lamp Reminder
™™ When ambient
temperature is
over 40°C in
operating, the
projector will
switch to Eco
automatically.
™™ Dynamic modelamp power can
be dynamically
adjusted from
100% to 30%.
Choose this function to show or to hide the warning message
when the changing lamp message is displayed.
The message will appear 30 hours before suggested replacement
of lamp.
Lamp Reminder
On
Off
Brightness Mode
`` Bright: Choose “Bright” to increase the brightness.
`` Eco.: Choose “Eco.” to dim the projector lamp which will lower
power consumption and extend the lamp life.
`` Dynamic: Choose “Dynamic” to dim the lamp power which will
be based on brightness level of the content and adjust lamp
power consumption between 100% and 30% dynamically. The
lamp life will be extended.
`` Eco+: When Eco+ mode is activated, the brightness level of
the content is automatically detected to significantly reduced
lamp power consumption (up to 70%) during periods of
inactivity.
Brightness Mode
Eco.
67
English
User Controls
Lamp Reset
Resets the lamp hour counter after replacing the lamp.
Lamp Reset
No
Yes
Lamp Reset ?
No
Yes
Exit
Choose “Exit” to exit the menu.
Lamp Behavior in different mode and function:
English
68
Brightness Mode
Bright
Eco.
Dynamic
Eco+
White Pattern
100%
80%
100%
80%
Dimming range
N/A
N/A
100%~30%
80%~30%
30% (Sleep
mode)
Black Pattern
100%
80%
30% (Sleep
mode)
AV Mute
30% (Sleep
mode)
30% (Sleep
mode)
30% (Sleep
mode)
30% (Sleep
mode)
Quick Resume
30% (Sleep
mode)
30% (Sleep
mode)
30% (Sleep
mode)
30% (Sleep
mode)
User Controls
OPTIONS
Advanced
OPTIONS |
Advanced
Direct Power On
Off
Signal Power On
Off
Auto Power Off (min)
Sleep Timer (min))
Quick Resume
Off
Eco.
Power Mode (Standby)
Remote Settings
Exit
Exit
Direct Power On
Choose “On” to activate Direct Power mode. The projector will
automatically power on when AC power is supplied, without
pressing the “ ” key on the projector Control Panel or on the
remote control.
Direct Power On
Off
™™ The Signal Power
On function is not
applicable if the
input source is
Video.
™™ (*)Functions vary
depending on
model definition.
On
Signal Power On*
Choose “On” to activate Signal Power mode. The projector
will automatically power on when a signal is detected, without
pressing the “ ” key on the projector Control Panel or on the
remote control.
Signal Power On
Off
On
69
English
User Controls
Auto Power Off (min)
™™ The value of
sleep timer will
be reset to zero
after the projector
power off.
Sets the countdown timer interval. The countdown timer will start,
when there is no signal being sent to the projector. The projector
will automatically power off when the countdown has finished (in
minutes).
Auto Power Off (min)
`` Press the
`` Press the
to decrease the timer interval.
to increase the timer interval.
Sleep Timer (min)
Sets the countdown timer interval. The countdown timer will start,
with or without a signal being sent to the projector. The projector
will automatically power off when the countdown has finished (in
minutes).
Sleep Timer (min)
`` Press the
`` Press the
to decrease the timer interval.
to increase the timer interval.
Quick Resume
`` On: If the projector is accidentally turned off, this feature
allows the projector to be instantly powered on again, if
selected within a period of 100 seconds.
`` Off: The fan will start cooling the system after 10 seconds
when user turns off the projector.
Quick Resume
Off
On
Power Mode (Standby)
`` Eco.: Choose “Eco.” to save power dissipation further < 0.5W.
`` Active: Choose “Active” to return to normal standby.
Power Mode (Standby)
Active
Exit
Choose “Exit” to exit the menu.
English
70
Eco.
User Controls
OPTIONS
Remote Settings
OPTIONS | Remote
Settings
USER 1
USER 2
USER 3
Test Pattern
Exit
USER 1
The default value is HDMI 2.
USER 1
HDMI 2
Press the
into the next menu and then press the
or
to
select HDMI 2/ VGA 2/ Test Pattern/ LAN/ Brightness/ Contrast/
Sleep Timer/ Color Matching/ Color Temp./ Gamma/ Source Lock
/ Projection/ Lamp Settings/ Zoom/ Freeze.
USER 2
The default value is VGA 2.
USER 2
VGA 2
Press the
into the next menu and then press the
or
to
select HDMI 2/ VGA 2/ Test Pattern/ LAN/ Brightness/ Contrast/
Sleep Timer/ Color Matching/ Color Temp./ Gamma/ Source Lock
/ Projection/ Lamp Settings/ Zoom/ Freeze.
USER 3
The default value is Test Pattern.
USER 3
Test Pattern
Press the
into the next menu and then press the
or
to
select HDMI 2/ VGA 2/ Test Pattern/ LAN/ Brightness/ Contrast/
Sleep Timer/ Color Matching/ Color Temp./ Gamma/ Source Lock
/ Projection/ Lamp Settings/ Zoom/ Freeze.
71
English
User Controls
OPTIONS
Filter Settings
OPTIONS | Filter
Settings
Filter Usage Hours
Filter Reminder
Off
500 hrs
Filter Reset
Exit
Filter Usage Hours
Display the filter time.
™™ “Filter Usage
Hours/ Filter
Reminder/ Filter
Reset” will only
appear when
“Optional Filter Installed” is “Yes”.
Filter Reminder
Choose this function to show or hide the warning message when
the changing filter message is displayed. (Factory default setting:
Off)
Filter Reminder
500 hrs
`` Press the
`` Press the
to decrease the time period.
to increase the time period.
Filter Reset
Reset the dust filter counter after replacing or cleaning the dust
filer.
Filter Reset
No
Exit
Choose “Exit” to exit the menu.
English
72
Yes
User Controls
OPTIONS
Filter Settings
OPTIONS | Filter
Settings
Filter Usage Hours
Optional Filter Installed
Yes
Filter Reminder
Off
Filter Reset
Exit
Optional Filter Installed (Depending on models)
Set the warning message setting.
OPTIONS
Filter Settings
Optional Filter Installed
No
Exit
`` Yes: Display warning message after 500 hours of use.
`` No: Turn off warning message.
73
English
Appendices
Troubleshooting
If you experience a problem with your projector, please refer to
the following information. If a problem persists, please contact
your local reseller or service center.
Image Problems
No image appears on-screen
`` Ensure all the cables and power connections are correctly and
securely connected as described in the “Installation” section.
`` Ensure the pins of connectors are not crooked or broken.
`` Check if the projection lamp has been securely installed.
Please refer to the “Replacing the Lamp” section.
`` Make sure the projector is switched on.
`` Ensure that the “AV Mute” feature is not turned on.
Image is out of focus
`` Make sure the projection screen is between the required
distance from the projector. (refer to pages 15-18)
The image is stretched when displaying 16:9 DVD title
`` When you play anamorphic DVD or 16:9 DVD, the projector
will show the best image in 16: 9 format on projector side.
`` If you play the LBX format DVD title, please change the format
as LBX in projector OSD.
`` If you play 4:3 format DVD title, please change the format as
4:3 in projector OSD.
`` If the image is still stretched, you will also need to adjust the
aspect ratio by referring to the following:
`` Please setup the display format as 16:9 (wide) aspect ratio
type on your DVD player.
Image is too small or too large
`` Move the projector closer to or further from the screen.
`` Press “Menu” on the projector panel, go to “DISPLAY-->
Format”. Try the different settings.
English
74
Appendices
Image has slanted sides:
`` If possible, reposition the projector so that it is centered on the
screen and below the bottom of the screen.
`` Use “DISPLAY-->V. Keystone” from the OSD to make an
adjustment.
Image is reversed
`` Select “SETUP-->Projection” from the OSD and adjust the
projection direction.
Blurry double image
`` Press “3D” button and switch to “Off” to avoid normal 2D
image is blurry double image.
Two images, side-by-side format
`` Press “3D” button and switch to “SBS” for input signal is HDMI
1.3 2D 1080i side-by-side.
Image does not display in 3D
`` Check if the battery of 3D glasses is drained.
`` Check if the 3D glasses is turned on.
`` When the input signal is HDMI 1.3 2D (1080i side-by-side
half), press “3D” button and switch to “SBS”.
75
English
Appendices
Other Problems
The projector stops responding to all controls
`` If possible, turn off the projector, then unplug the power cord
and wait at least 20 seconds before reconnecting power.
Lamp burns out or makes a popping sound
`` When the lamp reaches its end of life, it will burn out and may
make a loud popping sound. If this happens, the projector
will not turn on until the lamp module has been replaced. To
replace the lamp, follow the procedures in the “Replacing the
Lamp” section.
Remote Control Problems
If the remote control does not work
`` Check the operating angle of the remote control is within ±15°
both horizontally and vertically of on of the IR receivers on the
projector.
`` Make sure there are not any obstructions between the remote
control and the projector. Move to within 6 m (20 ft) of the
projector.
`` Make sure batteries are inserted correctly.
`` Replace batteries if they are exhausted.
English
76
Appendices
LED Lighting Messages
Message
Standby state
(Input power cord)
Power on
(Warming)
Lamp lighting
™™ Steady light 
No light 
On/Standby LED
Temp-LED
Lamp-LED
(Red/Green/Blue)
(Red)
(Red)
Red
Flashing Blue
Blue
Power off (Cooling)
Flashing Blue.
Red (cooling fan has
turned off)
Quick Resume (100
secs)
Flashing Blue
Error (Over temp.)
Flashing Red
Error (Fan failure)
Flashing Red
Error (Lamp failure)
Flashing Red
Flashing
77
English
Appendices
On Screen Messages
™™ Power off:
Power Off?
Press Power Key again
™™ Lamp warning:
Lamp Warning
Lamp life exceeded.
™™ Temperature warning:
Warning TEMPERATURE TOO HIGH
Please
1. Make sure air in and outlets are not blocked.
2. Make sure the environment temperature is under 40 degree C.
If the problem persists in spite of the above.
Please contact local service centre for repair.
™™ Fan failed:
Warning FAN LOCKED
The Projector will switch off automatically.
Please contact local service centre for repair.
™™ Out of display range:
HDMI
Out Of Range
English
78
Appendices
Replacing the Lamp
The projector automatically detects the lamp life. When the
lamp life is nearing the end of use, you will receive a warning
message.
Lamp Warning
Lamp life exceeded.
When you see this message, please contact your local reseller or
service center to change the lamp as soon as possible. Make sure
the projector has been cooled down for at least 30 minutes before
changing the lamp.
,
,
;
;
,
,
,
,
Warning: If ceiling mounted, please use caution when
opening the lamp access panel. It is recommended to wear
safety glasses if changing the bulb when ceiling mounted.
“Caution must be used to prevent any loose parts from falling
out of projector.”
Warning: Lamp compartment is hot! Allow it to cool down
before changing lamp!
Warning: To reduce the risk of personal injury, do not drop
the lamp module or touch the lamp bulb. The bulb may
shatter and cause injury if it is dropped.
79
English
Appendices
3
The screw on the
lamp cover and the
lamp cannot be
removed.
The projector
cannot be turned
on if the lamp
cover has not been
placed back on the
projector.
Do not touch the
glass area of the
lamp. Hand oil can
cause the lamp to
shatter. Use a dry
cloth to clean the
lamp module if it
was accidentally
touched.
4
Lamp Replacement Procedure:
1. Switch off the power to the projector by pressing the “ ” button on the remote
control or on the Control Panel of the projector.
2. Allow the projector to cool down for at least 30 minutes.
3. Disconnect the power cord.
4. Press the release button to disengage the lamp cover from the main unit. 1
5. Use your fingernail to pry the lamp cover loose and then remove it. 2
6. Unscrew the two screws on the lamp module. 3
7. Lift up the lamp handle 4 and remove the lamp module slowly and carefully. 5
To replace the lamp module, reverse the previous steps.
10. Turn on the projector and reset the lamp timer.
Lamp Reset: (i) Press “Menu”  (ii) Select “OPTIONS”  (iii) Select
“Lamp Settings”  (iv) Select “Lamp Reset”  (v) Select “Yes”.
English
80
Appendices
Installing and Cleaning the Dust
Filter
Dust filters are
only required/
supplied in
selected regions
with excessive
dust.
We recommend you clean the dust filter every 500 hours of
operation, or more often if you are using the projector in a
dusty environment.
When the warning message appears on the screen, do the
following to clean the air filter:
The usage time of the dust filter is reched.
Please clean the dust filters for better performance.
2
1
1
2
Air Filter Cleaning Procedure:
1. Switch off the power to the projector by pressing the “ ” button on the remote
control or on the Control Panel of the projector.
2. Disconnect the power cord.
3. Pull out the latch to remove the dust filter compartment, as shown in the illustration.
1
4. Carefully remove the air filter. Then clean or replace the dust filter. 2
To install the dust filter, reverse the previous steps.
5. Turn on the projector and reset the filter usage counter after the dust filter is
replaced.
81
English
Appendices
Compatibility Modes
Digital compatibility
B0/Established Timing
B0/Standard Timing
B0/Detail Timing
B1/Video Mode
B1/Detail Timing
720 x 400 @ 70Hz
XGA / WXGA:
Native timing:
640 x 480p @ 60Hz
720 x 480p @ 60Hz
640 x 480 @ 60Hz
1440 x 900 @ 60Hz
XGA: 1024 x 768 @ 60Hz
720 x 480p @ 60Hz
1280 x 720p @ 60Hz
640 x 480 @ 67Hz
1024 x 768 @ 120Hz
WXGA: 1280 x 800 @ 60Hz
1280 x 720p @ 60Hz
1366 x 768 @ 60Hz
640 x 480 @ 72Hz
1280 x 800 @ 60Hz
1080P: 1920 x 1080 @ 60Hz
1920 x 1080i @ 60Hz
1920 x 1080i @ 50Hz
640 x 480 @ 75Hz
1280 x 1024 @ 60Hz
720(1440) x 480i @ 60Hz
1920 x 1080p @ 60Hz
800 x 600 @ 56Hz
1680 x 1050 @ 60Hz
1920 x 1080p @ 60Hz
800 x 600 @ 60Hz
1280 x 720 @ 60Hz
720 x 576p @ 50Hz
800 x 600 @ 72Hz
1280 x 720 @ 120Hz
1280 x 720p @ 50Hz
800 x 600 @ 75Hz
1600 x 1200 @ 60Hz
1920 x 1080i @ 50Hz
1024 x 768 @ 60Hz
720(1440) x 576i @ 50Hz
1024 x 768 @ 70Hz
1080P / WUXGA:
1920 x 1080p @ 50Hz
1024 x 768 @ 75Hz
1280 x 720 @ 60Hz
1920 x 1080p @ 24Hz
1280 x 1024 @ 75Hz
1280 x 800 @ 60Hz
1920 x 1080p @ 30Hz
1280 x 1024 @ 60Hz
1400 x 1050 @ 60Hz
1600 x 1200 @ 60Hz
1440 x 900 @ 60Hz
1280 x 720 @ 120Hz
1024 x 768 @ 120Hz
VGA analog compatibility
B0/Established Timing
B0/Standard Timing
B0/Detail Timing
720 x 400 @ 70Hz
XGA / WXGA:
Native timing:
640 x 480 @ 60Hz
1440 x 900 @ 60Hz
XGA: 1024 x 768 @ 60Hz
640 x 480 @ 67Hz
1024 x 768 @ 120Hz
WXGA: 1280 x 800 @ 60Hz
640 x 480 @ 72Hz
1280 x 800 @ 60Hz
1080P: 1920 x 1080 @ 60Hz
640 x 480 @ 75Hz
1280 x 1024 @ 60Hz
800 x 600 @ 56Hz
1680 x 1050 @ 60Hz
800 x 600 @ 60Hz
1280 x 720 @ 60Hz
800 x 600 @ 72Hz
1280 x 720 @120Hz
800 x 600 @ 75Hz
1600 x 1200 @ 60Hz
1024 x 768 @ 60Hz
1024 x 768 @ 70Hz
English
82
1080P / WUXGA:
B1/Video Mode
B1/Detail Timing
1366 x 768 @ 60Hz
Appendices
B0/Established Timing
B0/Standard Timing
1024 x 768 @ 75Hz
1280 x 720 @ 60Hz
1280 x 1024 @ 75Hz
1280 x 800 @ 60Hz
B0/Detail Timing
B1/Video Mode
B1/Detail Timing
1280 x 1024 @ 60Hz
1400 x 1050 @ 60Hz
1600 x 1200 @ 60Hz
1440 x 900 @ 60Hz
1280 x 720 @ 120Hz
1024 x 768 @ 120Hz
True 3D video compatibility
Input timing
HDMI 1.4a 3D
Input
Input resolution
1280 x 720P @ 50Hz
Top - and - Bottom
1280 x 720P @ 60Hz
Top - and - Bottom
1280 x 720P @ 50Hz
Frame packing
1280 x 720P @ 60Hz
Frame packing
1920 x 1080i @ 50 Hz
Side- by-Side (Half)
1920 x 1080i @ 60 Hz
Side- by-Side (Half)
1920 x 1080P @ 24 Hz
Top - and- Bottom
1920 x 1080P @ 24 Hz
Frame packing
1920 x 1080i @ 50Hz
1920 x1080i @ 60Hz
1280 x 720P @ 50Hz
Side-by-Side(Half)
SBS mode is on
Top-and-Bottom
TAB mode is on
HQFS
3D format is Frame sequential
1280 x 720P @ 60Hz
HDMI 1.3
1920 x 1080i @ 50Hz
1920 x1080i @ 60Hz
1280 x 720P @ 50Hz
1280 x 720P @ 60Hz
480i
83
English
Appendices
Ceiling Mount Installation
If you wish to use a third party ceiling mount kit, please
ensure the screws used to attach a mount to the projector
meet the following specifications:
Screw type: M4*4
Maximum screw length: 11mm
Minimum screw length: 8mm
384.58
130.00
310.1
88.00
Warning:
1. If you buy a ceiling
mount from another
company, please
be sure to use the
correct screw size.
Screw size will vary
depending on the
thickness of the
mounting plate.
2. Be sure to keep
at least 10 cm gap
between the ceiling
and the bottom of the
projector.
3. Avoid installing the
projector near a heat
source.
63.00
Please note that
damage resulting
from incorrect
installation will void
the warranty.
100
Unit: mm
English
84
Appendices
Regulations and safety notices
Compliant with Russian/ Ukraine regulatory certification
Radio device regulatory notice
-------------------------------------------Note: The regulatory information below is for models with
wireless LAN and/or Bluetooth only.
General
This product complies with the radio frequency and safety standards
of any country or region in which it has been approved for wireless
use. Depending on configurations, this product may or may not
contain wireless radio devices (such as wireless LAN and/or Bluetooth
modules).
Canada — Low-power license-exempt radio communication
devices (RSS-247)
a Common information
Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference
that may cause undesired operation of the device.
b Operation in 2.4 GHz band
To prevent radio interference to the licensed service, this device
is intended to be operated indoors and installation outdoors is
subject to licensing.
List of applicable countries
This device must be used in strict accordance with the regulations
and constraints in the country of use. For further information, please
contact the local office in the country of use. Please see
http://ec.europa.eu/enterprise/rtte/implem.htm for the latest country list.
85
English
Acer Incorporated
of Conformity
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi
New Taipei City 221, Taiwan
We,
Acer Incorporated
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi, New Taipei City 221, Taiwan
And,
Acer Italy s.r.l.
Via Lepetit, 40, 20020 Lainate (MI) Italy
Tel: +39-02-939-921 ,Fax: +39-02 9399-2913
www.acer.it
Product:
Trade Name:
Model Number:
DLP Projector
Acer
D1P1801/DWX1802/DNX1803
Marketing name: U5530/U5330W/U5230/R350/R320/R310/PU-F20/PU-W20/PU-X20/
SP150/SP130/SP110/FU-420/FU-320/FU-120
We, Acer Incorporated, hereby declare under our sole responsibility that the product described above is in
as below
and following
conformity with the relevant Union
harmonized standards and/or other relevant standards have been applied:
EMC Directive: 2014/30/EU
EN 55032:2015+AC:2016, Class B
EN 55024:2010+A1:2015
EN 61000-3-2:2014, Class A
EN 61000-3-3:2013
R&TTE Directive: 1999/5/EC (until Jun 12, 2017)
RED Directive: 2014/53/EU (From Jun 13, 2017)
EN 300 328 V1.8.1
EN 301 893 V1.7.1
EN 300 440-1 V1.6.1
EN 300 440-2 V1.4.1
EN 302 291-1 V1.1.1
EN 302 291-2 V1.1.1
EN 301 511 V9.0.2
EN 301 908-1 V6.2.1
EN 301 908-2 V6.2.1
EN 301 908-13 V6.2.1
EN 301 489-1 V1.9.2
EN 301 489-3 V1.6.1
EN 301 489-7 V1.3.1
EN 301 489-17 V2.2.1
EN 301 489-24 V1.5.1
EN 50360:2001
EN 50566:2013
EN 62479:2010
EN 62311:2008
EN 62209-1:2006
EN 62209-2:2010
LVD Directive: 2014/35/EU
EN 60950-1:2006/A11:2009/A1:2010/A12:2011/A2:2013
EN 50332-1:2000
EN 50332-2:2003
RoHS Directive: 2011/65/EU
EN 50581:2012
ErP Directive: 2009/125/EC
Regulation (EU) No. 617/ 2013
Regulation (EC) No. 1275/2008; EN 50564:2011
Regulation (EC) No. 278/2009; EN 50563:2011
Year to begin affixing CE marking 2018.
_______________________________
RU Jan / Sr. Manager
Acer Incorporated (Taipei, Taiwan)
Jun. 28, 2018
Date
Download PDF