Philips | 191V2SB/94 | Philips LCD-Monitor mit SmartControl Lite 191V2SB/01 Bedienungsanleitung

191V2
www.philips.com/welcome
EN User manual
1
Customer care and warranty
27
Troubleshooting & FAQs
39
Table of Contents
1
1.1
1.2
1.3
Important
Safety precautions and maintenance................ 1
Notational Descriptions.......................................... 2
Disposal of product and packing material.... 3
2
2.1
2.2
2.3
Setting up the monitor
Installation........................................................................ 4
Operating the monitor............................................ 5
Remove Base Stand and Base.............................. 7
3
3.1
3.2
3.3
Product information
SmartContrast.............................................................. 7
SmartControl Lite....................................................... 8
Philips Pixel Defect Policy....................................... 15
4
Technical Specifications.................................. 17
4.1 Resolution & Preset Modes.................................. 20
4.2 Automatic PowerSaving........................................... 20
5
Regulatory Information.................................. 21
6
Customer care and warranty....................... 27
7
7.1
7.2
7.3
Troubleshooting & FAQs
Troubleshooting........................................................... 39
SmartControl Lite FAQs......................................... 41
General FAQs............................................................... 43
2010 © Koninklijke Philips Electronics N.V. All rights reserved.
Philips and the Philips Shield Emblem are registered trademarks of Koninklijke
Philips Electronics N.V. and are used under license from Koninklijke Philips
Elecrtonics N.V.
Specifications are subject to change without notice.
•
•
1. Important
This electronic user’s guide is intended for anyone
who uses the Philips monitor. Take time to read
this user manual before you use your monitor.
It contains important information and notes
regarding operating your monitor.
Do not subject the monitor to severe vibration or high impact conditions during operation.
Do not knock or drop the monitor during operation or transportation.
Maintenance
• To protect your monitor from possible damage, do not put excessive pressure on the LCD panel. When moving your monitor, grasp the frame to lift; do not lift the
monitor by placing your hand or fingers on the LCD panel.
• Unplug the monitor if you are not going to use it for an extensive period of time.
• Unplug the monitor if you need to clean it with a slightly damp cloth. The screen may be wiped with a dry cloth when the power is
off. However, never use organic solvent, such as, alcohol, or ammonia-based liquids to clean your monitor.
• To avoid the risk of shock or permanent damage to the set, do not expose the monitor to dust, rain, water, or excessive moisture environment.
• If your monitor gets wet, wipe it with dry cloth as soon as possible.
• If foreign substance or water gets in your
monitor, please turn the power off immediately and disconnect the power cord. Then, remove the foreign substance or water, and send it to the maintenance center.
• Do not store or use the monitor in locations exposed to heat, direct sunlight or extreme cold.
• In order to maintain the best performance of your monitor and use it for a longer lifetime, please use the monitor in a location that falls within the following temperature and humidity ranges.
o Temperature: 0-40°C 32-95°F
o Humidity: 20-80% RH
The Philips guarantee applies provided the
product is handled properly for its intended use,
in accordance with its operating instructions and
upon presentation of the original invoice or cash
receipt, indicating the date of purchase, dealer’s
name and model and production number of the
product.
1.1Safety precautions and maintenance
Warnings
Use of controls, adjustments or procedures other
than those specified in this documentation may
result in exposure to shock, electrical hazards
and/or mechanical hazards.
Read and follow these instructions when
connecting and using your computer monitor.
Operation
• Keep the monitor out of direct sunlight and away from stoves or any other heat source.
• Remove any object that could fall into ventilation holes or prevent proper cooling of the monitor’s electronics.
• Do not block the ventilation holes on the cabinet.
• When positioning the monitor, make sure the power plug and outlet are easily accessible.
• If turning off the monitor by detaching the power cable or DC power cord, wait for 6 seconds before attaching the power cable or DC power cord for normal operation.
• Please use approved power cord provided
by Philips all the time. If your power cord is missing, please contact with your local service center. (Please refer to Customer Care Consumer Information Center)
1
•
1.2Notational Descriptions
IMPORTANT: Always activate a moving screen saver program when you leave your monitor unattended. Always activate a periodic screen refresh application if your monitor will display unchanging static content. Uninterrupted display of still or static images over an extended period may
cause “burn in”, also known as “after-imaging”
or “ghost imaging”, on your screen.
"Burn-in", "after-imaging", or "ghost imaging" is a well-known phenomenon in LCD panel technology. In most cases, the “burned in” or “after-imaging” or “ghost imaging” will disappear gradually over a period of time after the power has been switched off.
The following subsections describe notational
conventions used in this document.
Notes, Cautions and Warnings
Throughout this guide, blocks of text may be
accompanied by an icon and printed in bold or
italic type. These blocks contain notes, cautions or
warnings. They are used as follows:
Note
This icon indicates important information and tips
that help you make better use of your computer
system.
Caution
This icon indicates information that tells you how
to avoid either potential damage to hardware or
loss of data.
Warning
Severe” burn-in” or “after-image” or “ghost image”
symptoms will not disappear and cannot be
repaired. The damage mentioned above is not
covered under your warranty.
Warning
This icon indicates the potential for bodily harm
and tells you how to avoid the problem.
Some warnings may appear in alternate formats
and may not be accompanied by an icon. In such
cases, the specific presentation of the warning is
mandated by the relevant regulatory authority.
Service
• The casing cover should be opened only by qualified service personnel.
• If there is any need for any document for repair or integration, please contact with your local service center. (please refer to the chapter of "Consumer Information Center")
• For transportation information, please refer to "Technical Specifications".
• Do not leave your monitor in a car/trunk under direct sun light.
Note
Consult a service technician if the monitor does
not operate normally, or you are not sure what
procedure to take when the operating instructions
given in this manual have been followed.
2
Recycling Information for Customers
There is currently a system of recycling up and
running in the European countries, such as The
Netherlands, Belgium, Norway, Sweden and
Denmark.
In Asia Pacific, Taiwan, the products can be taken
back by Environment Protection Administration
(EPA) to follow the IT product recycling
management process, detail can be found in web
site www.epa.gov.tw
The monitor contains parts that could cause
damage to the nature environment. Therefore, it is
vital that the monitor is recycled at the end of its
life cycle.
For help and service, please contact Consumers
Information Center or F1rst Choice Contact
Information Center in each country.
1.3Disposal of product and packing material
Waste Electrical and Electronic EquipmentWEEE
This marking on the product or on its packaging
illustrates that, under European Directive 2002/96/
EC governing used electrical and electronic
appliances, this product may not be disposed
of with normal household waste. You are
responsible for disposal of this equipment through
a designated waste electrical and electronic
equipment collection. To determine the locations
for dropping off such waste electrical and
electronic, contact your local government office,
the waste disposal organization that serves your
household or the store at which you purchased
the product.
Your new monitor contains materials that can be
recycled and reused. Specialized companies can
recycle your product to increase the amount of
reusable materials and to minimize the amount to
be disposed of.
All redundant packing material has been omitted.
We have done our utmost to make the packaging
easily separable into mono materials.
Please find out about the local regulations on how
to dispose of your old monitor and packing from
your sales representative.
3
Connecting to your PC
2. Setting up the monitor
2.1Installation
191V2
Package contents
LCD Monitor
Monitor LCD / Monitor LCD / LCD-Monitor / Moniteur LCD /
LCD Monitor / LCD监视器 / LCD-монитором
191V
191V
1 -813 -2A
191V
1VE
1
TQ7
0G 19
C
Guide de démarrage rapide / Guía rápida / Kurzanleitung /
Guida rapida / H�
zl�
başlangiç k�
lavuzu / 快速入门指南 /
Краткое руководство по запуску
M2
19
Kurulum 安装
连接性
Monitor
Power cord
Quick start guide
VGA signal cable
EDFU CD
Audio cable (optional)
人体工程学调整
DVI cable (opti
oonal)
AC power input
VGA input
PC Audio input(Available for selected models)
Kensington anti-thief lock
DVI-D input(Available for selected models)
Connect to PC
Install base stand
1.
2.
3.
4.
5.
191V2
1. Place the monitor face down a smooth surface taking care to avoid scratching or damaging the screen.
Connect the power cord to the back of the monitor firmly.
Turn off your computer and unplug its power cable.
Connect the monitor signal cable to the video connector on the back of your computer.
Plug the power cord of your computer and your monitor into a nearby outlet.
Turn on your computer and monitor. If the monitor displays an image, installation is complete.
2.2Operating the monitor
2. Hold the monitor base stand with both hands and firmly insert the base stand into the base column.
191V
CLICK!
CLICK!
4
The OSD Menu
Below is an overall view of the structure of the
On-Screen Display. You can use this as a reference
when you want to work your way around the
different adjustments later on.
Front view product description
Main menu
Input
: To switch monitor’s power ON and OFF
: To access the OSD menu
: To adjust brightness of the display
:Auto picure control switching in wide
and 4:3 format
: Automatically adjust the horizontal
position, vertical position, phase and clock settings./
Return to previous OSD level.
Sub menu
VGA
DVI (available for selective models)
Picture
Picture Format - 4:3, Wide screen
Brightness
Contrast
SmartContrast - On, Off
Color
Gamma
- 1.8, 2.0, 2.2, 2.4, 2.6
Color Temp.
- 5000K, 6500K, 7500K, 8200K, 9300K, 11500K
sRGB
User Define
Red
Green
Blue
Language
Description of the On Screen Display
English, Español, Français, Deutsch, Italiano
Português, PycckИЙ, 簡體中文
What is On-Screen Display (OSD)?
OSD Settings
Horizontal
Vertical
Transparency - Off, 1, 2, 3, 4
On-Screen Display (OSD) is a feature in all Philips
LCD monitors. It allows an end user to adjust
screen performance or select functions of the
monitors directly through an on-screen instruction
window. A user friendly on screen display interface
is shown as below:
OSD Time out - 5, 10, 20, 30, 60
Setup
Power LED
- 0, 1, 2, 3, 4
H. Position
- 0 ~ 100
V. Position
- 0 ~ 100
Phase
- 0 ~ 100
Clock
- 0 ~ 100
Resolution Notification - On, Off
Reset
- Yes, No
Information
Resolution notification
This monitor is designed for optimal performance
at its native resolution, 1366×768@60Hz.
When the monitor is powered on at a different
resolution, an alert is displayed on screen: Use
1366×768@60Hz for best results.
Display of the native resolution alert can be switched off from Setup in the OSD (On Screen
Display) menu.
Basic and simple instruction on the control keys
In the OSD shown above users can press
buttons at the front bezel of the monitor to move
the cursor, OK to confirm the choice or change.
5
Physical Function
Tilt
191V
(191V2)
Note
This monitor accepts a 100mm x 100mm VESA-Compliant mounting interface.
2.3Remove Base Stand and Base
Remove the Base Stand
191V2
Place the monitor face on a safe surface, pull the
base stand away from the monitor.
100mm
100mm
Remove the Base
Condition:
• For VESA standard mounting applications
1. Separate the base from the base stand.
6
3. Product information
3.1SmartContrast
What is it?
Unique technology that dynamically analyzes
displayed content and automatically optimizes
a LCD monitor's contrast ratio for maximum
visual clarity and viewing enjoyment, stepping up
backlighting for clearer, crisper and brighter images
or dimming backlighting for clear display of images
on dark backgrounds.
Why do I need it?
You want the very best visual clarity and viewing
comfort for every type of content. SmartContrast
dynamically controls contrast and adjusts
backlighting for clear, crisp, bright gaming and
video images or displays clear, readable text for
office work. By reducing your monitor's power
consumption, you save on energy costs and
extend the lifetime of your monitor.
How does it work?
When you activate SmartContrast, it will analyse
the content you are displaying in real time to
adjust colors and control backlight intensity. This
function will dynamically enhance contrast for a
great entertainment experience when viewing
videos or playing games.
7
3.2 Philips SmartControl Lite
First launch -Wizard
• The first time after installation of
SmartControl Lite, it will automatically
go to Wizard for first time launch.
• The wizard will guide you through
adjustment your monitor performance step
by step.
• You can go to Plug-in menu to launch wizard
later on as well.
• You can adjust more options without wizard
by Standard pane.
The new SmartControl Lite software by Phillips
allows you to control your monitor via an easy
to use on-screen graphic interface. Complicated
adjustments are a thing of the past as this user
friendly software guides you through
fine-tuning resolution, Color calibration,
Clock/Phase adjustments, RGB White point
adjustment, etc.
Equipped with latest technology in core algorithm
for fast processing and response, this Windows
7 compliant eye catching animated Icon based
software is ready to enhance your experience
with Philips monitors!
Installation
•
•
•
Follow the instruction and complete the
installation.
You can launch after installation is completed.
If you want to launch later, you can either
click the shortcut on desktop or toolbar.
8
Start with Standard pane:
Adjust menu:
• Adjust Menu allow you to adjust Brightness,
Contrast, Focus, Position and Resolution.
• You can follow the instruction and do the
adjustment.
• Cancel prompts user if you want to cancel
installation.
9
Color menu:
• Color Menu allow you to adjust RGB,
Black Level, White Point, Color Calibration,
and SmartImage Lite (Please refer to
SmartImage Lite section).
• You can follow the instruction and do the
adjustment.
• Refer to below table for sub-menu item base
on your input.
• Example for Color Calibration
1. "Show Me" starts color calibration tutorial.
2. Start - starts the 6-step color calibration
sequence.
3. Quick View loads the before/after images.
4. To return to Color home pane, click the
Cancel button.
5. Enable color calibration - by default is
on. If unchecked, does not allow for color
calibration to happen, dimes out start and
quick view buttons.
6. Must have patent info in calibration screen.
10
First color Calibration Screen:
•
•
•
•
Previous button is disabled until the second
color screen.
Next goes to the succeeding target
(6-targets).
Final next goes File>Presets pane.
Cancel closes the UI and returns to the plug
in page.
SmartImage Lite
Allows user to change setting for better display
setting based on content.
•
•
•
When Entertainment is set, SmartContrast and
SmartResponse are enabled.
•
•
Options>Preferences - Will only be active
when selecting Preferences from the drop-down
Options menu. On a non-supported display
capable of DDC/CI, only the Help and Options
tabs are available.
•
11
Displays current preference settings.
A checked box enables the feature. The
check box is a toggle.
Enable Context Menu on desktop is checked
(On) by default. Enable Context menu
displays SmartControl Lite selections
for Select Preset and Tune Display in the
desktop right-click context menu. Disabled
removes SmartControl Lite from the
right click context menu.
Enable Task Tray icon is checked (On) by
default. Enable context menu shows the task
tray menu for SmartControl Lite. A right
click on the task tray icon displays the menu
options for Help, Technical Support. Check
for Upgrade, About, and Exit. When Enable
task tray menu is disabled, the task tray icon
will only display EXIT.
Run at Startup is checked (On) by default.
When disabled, SmartControl Lite will
not launch at start or be in the task tray. The
only way to launch SmartControl Lite is
either from the desktop short cut or from the
program file. Any preset set to run at startup
will not load when this box is unchecked
(Disabled).
Enable transparency mode (Windows 7,
Vista, XP). Default is 0% Opaque.
Options>Input - Will only be active when
selecting Input from the drop-down Options
menu. On a non-supported display capable of
DDC/CI, only the Help and Options tabs are
available. All other SmartControl Lite tabs are not
available.
•
•
Display the Source instruction pane and
current input source setting.
On single input displays, this pane will not be
visible.
Options>Audio - Will only be active when
selecting Volume from the drop-down Options
menu.
On a non-supported display capable of DDC/CI,
only the Help and Options tabs are available.
Help>User Manual - Will only be active when
selecting User Manual from the drop-down Help
menu. On a non-supported display capable of
DDC/CI, only the Help and Options tabs are
available.
12
Context Sensitive menu
The Context Sensitive menu is Enabled by default.
If Enable Context Menu has been checked in the
Options>Preferences pane, then the menu will be
visible.
Help>Version - Will only be active when selecting
Version from the drop- down Help menu. On a
non-supported display capable of DDC/CI, only
the Help and Options tabs are available.
The Context Menu has four entries:
• SmartControl Lite - When selected the
About Screen is displayed.
• Select Preset - Provides a hierarchical menu
of saved presets for immediate use. A check
mark shows the currently selected preset.
Facoty Preset can also be called from the
drop down menu.
• Tune Display - Opens the SmartControl
Lite control panel.
• SmartImage Lite - Check current settings,
Standard, Internet, Game.
13
Task Tray Menu Disabled
When the Task Tray is disabled in the preference
folder, only the EXIT selection is available.
To completely remove SmartControl Lite
from the task tray, disable Run at Startup in
Options>Preferences.
Task Tray Menu Enabled
The task tray menu can be displayed by rightclicking on the SmartControl Lite icon from the
task tray. Left Click will launch the application.
The task tray has five entries:
• Help - Access to User Manual file: Open
User Manual file using the default browser
window.
• Technical Support - displays the tech support
page.
• Check for Update - takes the user to PDI
Landing and checks the user's version against
the most current available.
• About - Displays detailed reference
information: product version, release
information, and product name.
• Exit - Close SmartControl Lite
To run SmartControl Lite again either
select SmartControl Lite from Program
menu, double-click the desktop PC icon or
restart the system.
14
3.3Philips' Flat Panel Monitors Pixel Defect Policy
Types of Pixel Defects
Pixel and sub pixel defects appear on the screen
in different ways. There are two categories of pixel
defects and several types of sub pixel defects
within each category.
Philips strives to deliver the highest quality
products. We use some of the industry's most
advanced manufacturing processes and practice
stringent quality control. However, pixel or sub
pixel defects on the TFT LCD panels used in flat
panel monitors are sometimes unavoidable. No
manufacturer can guarantee that all panels will
be free from pixel defects, but Philips guarantees
that any monitor with an unacceptable number
of defects will be repaired or replaced under
warranty. This notice explains the different types
of pixel defects and defines acceptable defect
levels for each type. In order to qualify for repair
or replacement under warranty, the number of
pixel defects on a TFT LCD panel must exceed
these acceptable levels. For example, no more
than 0.0004% of the sub pixels on a 18.5" XGA
monitor may be defective. Furthermore, Philips
sets even higher quality standards for certain
types or combinations of pixel defects that are
more noticeable than others. This policy is valid
worldwide.
Bright Dot Defects Bright dot defects appear as
pixels or sub pixels that are always lit or 'on'. That
is, a bright dot is a sub-pixel that stands out on the
screen when the monitor displays a dark pattern.
There are the types of bright dot defects:
One lit red, green or blue sub pixel
Two adjacent lit sub pixels:
- Red + Blue = Purple
- Red + Green = Yellow
- Green + Blue = Cyan (Light Blue)
Pixels and Sub pixels
A pixel, or picture element, is composed of three
sub pixels in the primary colors of red, green and
blue. Many pixels together form an image. When
all sub pixels of a pixel are lit, the three colored
sub pixels together appear as a single white pixel.
When all are dark, the three colored sub pixels
together appear as a single black pixel. Other
combinations of lit and dark sub pixels appear as
single pixels of other colors.
Three adjacent lit sub pixels (one white pixel)
15
Note
A red or blue bright dot must be more than 50
percent brighter than neighboring dots while
a green bright dot is 30 percent brighter than
neighboring dots.
Black Dot Defects Black dot defects appear as
pixels or sub pixels that are always dark or 'off'.
That is, a dark dot is a sub-pixel that stands out
on the screen when the monitor displays a light
pattern. These are the types of black dot defects:
Proximity of Pixel Defects
Because pixel and sub pixels defects of the same
type that are near to one another may be more
noticeable, Philips also specifies tolerances for the
proximity of pixel defects.
Pixel Defect Tolerances
In order to qualify for repair or replacement due
to pixel defects during the warranty period, a TFT
LCD panel in a Philips flat panel monitor must
have pixel or sub pixel defects exceeding the
tolerances listed in the following tables.
BRIGHT DOT DEFECTS
MODEL
1 lit subpixel
2 adjacent lit subpixels
3 adjacent lit subpixels (one white pixel)
Distance between two bright dot defects*
Total bright dot defects of all types
ACCEPTABLE LEVEL
191V2
3
1
0
>15mm
3
BLACK DOT DEFECTS
MODEL
1 dark subpixel
2 adjacent dark subpixels
3 adjacent dark subpixels
Distance between two black dot defects*
Total black dot defects of all types
ACCEPTABLE LEVEL
191V2
5 or fewer
2 or fewer
0
>15mm
5 or fewer
TOTAL DOT DEFECTS
MODEL
Total bright or black dot defects of all types
ACCEPTABLE LEVEL
191V2
5 or fewer
Note
1 or 2 adjacent sub pixel defects = 1 dot defect
This monitor is ISO9241-307 compliant.
16
4 Technical Specifications
191V2
Picture/Display
LCD panel type
Backlight
Panel size
Aspect ratio
Pixel Pitch
Brightness
SmartContrast
Contrast ratio (typ.)
Response time (typical)
Optimum Resolution
Viewing angle
Picture Enhancement
Display colors
Vertical refresh rate
Horizontal Frequency
sRGB
Connectivity
Signal input
Input Signal
Convenience
User Convenience
OSD Languages
Other convenience
Plug & Play Compatibility
Stand
Tilt
TFT-LCD
CCFL
18.5" W( 47 cm)
16:9
0.300 x 0.300 mm
250 cd/m²
300000:1
1000:1
5 ms
1366x768 @ 60Hz
176° (H) / 170° (V) @ C/R > 5
Smartcontrol Lite
16.7 M
56Hz -76Hz
30kHz - 80kHz
YES
DVI-D (digital, HDCP), VGA (Analog)
Separate Sync, Sync on Green
4:3 Wide/ , Power On/Off , Menu (OK),
Brightness/ , AUTO/back,
English, French, German, Italian, Russian, Spanish,
Simplified Chinese, Portuguese
VESA mount ( 100 x 100mm), Kensington lock
DDC/CI, sRGB, Windows 7/Vista/XP, Mac OSX, Linux
-5/+20 (191V2)
17
Power
On mode
(EnergyStar 5.0 test method)
Energy Consumption
(EnergyStar 5.0 test method)
Normal Operation (typical)
Sleep
Off
Heat Dissipation*
Normal Operation
Sleep
Off
Power LED indicator
Power Supply
Dimension
Product with stand (WxHxD)
Product without stand
(WxHxD)
Box dimension (WxHxD)
Weight
Product with stand
Product without stand
Product with packaging
Operating Condition
Temperature range (operation)
Temperature range (operation)
Relative humidity
Altitude
MTBF
16.6W
AC Input Voltage at AC Input Voltage at AC Input Voltage at
100VAC +/-5VAC,
115VAC +/-5VAC,
230VAC +/-5VAC,
50Hz +/- 3Hz
60Hz +/- 3Hz
50Hz +/ -3Hz
15.66W
15.48W
15.55W
0.15W
0.16W
0.2W
0.15W
0.14W
0.12W
AC Input Voltage at AC Input Voltage at AC Input Voltage at
100VAC +/-5VAC, 115VAC +/-5VAC,
230VAC +/-5VAC,
50Hz +/ -3Hz
60Hz +/ -3Hz
50Hz +/ -3Hz
15.83W
15.98W
16.12W
0.15W
0.15W
0.18W
0.11W
0.12W
0.14W
On mode: Green, Standby/Sleep mode: Amber
Build-in, 100-240VAC, 50/60Hz
445 x335 x161mm
445x270x64mm
490x350x128mm
3.48kg
3.23kg
4.61Kg
0°C to 40 °C
-20°C to 60°C
20% to 80%
Non-operation: + 12,000 ft ( 3,658 m)
operation: + 40,000 ft ( 12,192 m)
50000 hrs
18
Environmental
ROHS
EPEAT
Packaging
Compliance and standards
Regulatory Approvals
Cabinet
Color
Finish
YES
Silver. (www.epeat.net)
100% recyclable
CE Mark, FCC Class B, SEMKO, TCO5.0, TÜV/
GS, TÜV Ergo, UL/cUL, Energy star 5.0, TCO5.0
Black/Black
Texture
Note
This data is subject to change without notice.
Go to www.philips.com/support to download the latest version of leaflet.
19
4.2Automatic PowerSaving
4.1Resolution & Preset Modes
Maximum Resolution
For 191V2
1366 x 768 at 60 Hz (analog input)
1366 x 768 at 60 Hz (digital input)
Recommended Resolution
For 191V2
1366 x 768 at 60 Hz (digital input)
H. freq (kHz)
31.469
31.469
31.469
35.000
37.500
35.156
37.879
46.875
48.363
60.023
63.981
79.976
55.469
55.935
70.635
66.587
Resolution
640x350
720x400
640x480
640x480
640x480
800x600
800x600
800x600
1024x768
1024x768
1280x1024
1280x1024
1440x900
1440x900
1440x900
1920x1080
65.290
64.674
1680x1050
1680x1050
If you have VESA DPM compliance display card
or software installed in your PC, the monitor can
automatically reduce its power consumption when
not in use. If an input from a keyboard, mouse or
other input device is detected, the monitor will
'wake up' automatically. The following table shows
the power consumption and signaling of this
automatic power saving feature:
Power Management Definition
V. freq (Hz)
70.086
70.086
59.940
67.000
75.000
56.250
60.317
75.000
60.004
75.029
60.020
75.025
59.901
59.887
74.984
60.000
VESA
Mode
Active
Video
H-sync
V-sync
ON
Yes
Yes
Sleep
OFF
No
No
Switch Off
OFF
-
-
Power
Used
< 16.6 W
(typ.)
< 29 W
(max.)
< 0.8 W
(typ.)
< 0.5 W
(typ.)
LED color
Green
Amber
OFF
This monitor is ENERGY STAR ® compliant. As an ENERGY STAR ®
Partner, we have determined that this product meets the ENERGY STAR®
guidelines for energy efficiency.
The following setup is used to measure power
consumption on this monitor.
Native resolution: 1366 x 768
Contrast: 50%
Brightness: 250 nits
Color temperature: 6500k with full white pattern
Audio (Off)
(reduce blinking)
Note
This data is subject to change without notice.
60.000
60.000
20
• Calibrated color temperature and gamma curve
• Wide luminance level, Dark black levels, Low motion blur
5 Regulatory Information
Lead-free Product
Electrical Safety
• Product fulfills rigorous safety standards
Emissions
• Low alternating electric and magnetic fields emissions
• Low acoustic noise emissions
Some of the Environmental features of the TCO Displays 5.0 requirements:
• The brand owner demonstrates corporate social responsibility and has a certified environmental management system (EMAS or ISO 14001)
• Very low energy consumption both in on- and standby mode
• Restrictions on chlorinated and brominated flame retardants, plasticizer and polymers
• Restrictions on heavy metals such as cadmium, mercury and lead (RoHS compliance)
Lead free display promotes
environmentally sound recovery and
disposal of waste from electrical and
electronic equipment. Toxic substances
like Lead has been eliminated and compliance
with European community’s stringent RoHs
directive mandating restrictions on hazardous
substances in electrical and electronic equipment
have been adhered to in order to make Philips
monitors safe to use throughout its life cycle.
TCO Displays 5.0 Information
Congratulations,
Your display is designed for both
you and the planet!
This display carries the TCO
Certified label. This ensures that
the display is designed for minimal impact on the
climate and natural environment, while offering
all the performance expected from top of the
line electronic products. TCO Certified is a third
party verified program, where every product
model is tested by an accredited independent
test laboratory. TCO Certified represents one of
the toughest certifications for displays worldwide.
EPEAT
(www.epeat.net)
“The EPEAT (Electronic Product
Environmental Assessment Tool)
program evaluates computer
desktops, laptops, and monitors
based on 51 environmental criteria
developed through an extensive stakeholder
consensus process supported by US EPA.
EPEAT system helps purchasers in the public
and private sectors evaluate, compare and select
desktop computers, notebooks and monitors
based on their environmental attributes. EPEAT
also provides a clear and consistent set of
performance criteria for the design of products,
and provides an opportunity for manufacturers to
secure market recognition for efforts to reduce
the environmental impact of its products.”
Some of the Usability features of the TCO
Displays 5.0 requirements:
Visual Ergonomics
Good visual ergonomics in order to improve the
working environment for the user and to reduce
sight and strain problems. Important parameters
are:
•Light levels without color tint, Uniform color
and luminance, Wide color gamut
21
This monitor is equipped with a function for saving
energy which supports the VESA Display Power
Management (DPM) standard. This means that the
monitor must be connected to a computer which
supports VESA DPM. Time settings are adjusted
from the system unit by software.
Benefits of EPEAT
Reduce use of primary materials
Reduce use of toxic materials
Avoid the disposal of hazardous waste EPEAT’S
requirement that all registered products meet
ENERGY STAR’s energy efficiency specifications,
means that these products will consume less
energy throughout their life.
Normal
operation
Power Saving
Alternative 2
One step
CE Declaration of Conformity
This product is in conformity with the following
standards
• EN60950-1:2006 (Safety requirement of Information Technology Equipment)
• EN55022:2006 (Radio Disturbance requirement of Information Technology Equipment)
• EN55024:1998+A1:2001+A2:2003 (Immunity requirement of Information Technology Equipment)
• EN61000-3-2:2006 (Limits for Harmonic Current Emission)
• EN61000-3-3:1995+A1:2001+A2:2005 (Limitation of Voltage Fluctuation and Flicker)
following provisions of directives applicable
• 2006/95/EC (Low Voltage Directive)
• 2004/108/EC (EMC Directive)
• 2005/32/EC (EuP Directive, EC No. 1275/2008 mplementing Directive for Standby and Off mode power consumption) and is produced by a manufacturing organization on ISO9000 level.
The product also comply with the following standards
• ISO9241-307:2008 (Ergonomic requirement, Analysis and compliance test methods for electronic visual displays)
• GS EK1-2000:2009 (GS mark requirement) • prEN50279:1998 (Low Frequency Electric and Magnetic fields for Visual Display)
• MPR-II (MPR:1990:8/1990:10 Low Frequency Electric and Magnetic fields)
• TCO Displays 5.0 (Requirement for
Environment Labeling of Ergonomics, Energy, Ecology and Emission, TCO: Swedish Confederation of Professional Employees) for TCO versions
VESA State
LED Indicator
ON (Active)
Green
Power
Consumption
< 16.6 W (typ.)
Sleep
Switch Off
Amber
OFF
< 0.8 W (typ.)
< 0.5 W (typ.)
As an ENERGY STAR® Partner,
we have determined that this
product meets the ENERGY STAR®
guidelines for energy efficiency.
Note
We recommend you switch off the monitor when
it is not in use for a long time.
22
FCC Declaration of Conformity
Federal Communications Commission (FCC)
Notice (U.S. Only)
•
•
•
•
Declaration of Conformity for Products Marked
with FCC Logo,
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC
Rules. These limits are designed to
provide reasonable protection against
harmful interference in a residential
installation. This equipment generates, uses
and can radiate radio frequency energy and,
if not installed and used in accordance with
the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off and on, the user
is encouraged to try to correct the
interference by one or more of the following
measures:
Reorientorrelocatethereceivingantenna.
Increasetheseparationbetweenthe
equipment and receiver.
Connecttheequipmentintoanoutleton
a circuit different from that to which the
receiver is connected.
Consultthedealeroranexperiencedradio/
TV technician for help.
United States Only
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user's authority
to operate the equipment.
Use only RF shielded cable that was supplied with
the monitor when connecting this monitor to a
computer device.
To prevent damage which may result in fire or
shock hazard, do not expose this appliance to rain
or excessive moisture.
THIS CLASS B DIGITAL APPARATUS MEETS
ALL REQUIREMENTS OF THE CANADIAN
INTERFERENCE-CAUSING EQUIPMENT
REGULATIONS.
23
EN 55022 Compliance (Czech Republic Only)
Commission Federale de la Communication
(FCC Declaration)
•
•
•
•
Cet équipement a été testé et déclaré conforme auxlimites des appareils numériques de class B,aux termes de l'article 15 Des règles de la FCC. Ces limites sont conçues de façon à fourir une
protection raisonnable contre les interférences nuisibles dans le cadre d'une installation résidentielle.
CET appareil produit, utilise et peut émettre des hyperfréquences qui, si l'appareil n'est pas installé et utilisé selon les consignes données, peuvent causer des interférences nuisibles aux communications radio.
Cependant, rien ne peut garantir l'absence d'interférences dans le cadre d'une installation particulière. Si cet appareil est la cause d'interférences nuisibles pour la réception des signaux de radio ou de télévision, ce qui peut être décelé en fermant l'équipement, puis en le remettant en fonction, l'utilisateur pourrait essayer de corriger la situation en prenant les mesures suivantes:
Réorienter ou déplacer l'antenne de réception.
Augmenter la distance entre l'équipement et le récepteur.
Brancher l'équipement sur un autre circuit que celui utilisé par le récepteur.
Demander l'aide du marchand ou d'un technicien chevronné en radio/télévision.
Toutes modifications n'ayant pas reçu l'approbation des services compétents en matière de conformité est susceptible d'interdire à l'utilisateur l'usage du présent équipement.
N'utiliser que des câbles RF armés pour les
connections avec des ordinateurs ou
périphériques.
CET APPAREIL NUMERIQUE DE LA CLASSE
B RESPECTE TOUTES LES EXIGENCES DU
REGLEMENT SUR LE MATERIEL BROUILLEUR
DU CANADA.
24
Polish Center for Testing and Certification
Notice
North Europe (Nordic Countries) Information
Placering/Ventilation
VARNING:
FÖRSÄKRA DIG OM ATT HUVUDBRYTARE
OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU
STÄLLER DIN UTRUSTNING PÅPLATS.
The equipment should draw power from a socket
with an attached protection circuit (a threeprong socket). All equipment that works together
(computer, monitor, printer, and so on) should
have the same power supply source.
The phasing conductor of the room's electrical
installation should have a reserve short-circuit
protection device in the form of a fuse with a
nominal value no larger than 16 amperes (A).
Placering/Ventilation
ADVARSEL:
S Ø R G V E D P L A C E R I N G E N F O R , AT
NETLEDNINGENS STIK OG STIKKONTAKT ER
NEMT TILGÆNGELIGE.
To completely switch off the equipment, the
power supply cable must be removed from the
power supply socket, which should be located
near the equipment and easily accessible.
Paikka/Ilmankierto
VAROITUS:
SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO
VO I DA A N TA R V I T TA E S S A H E L P O S T I
IRROTTAA PISTORASIASTA.
A protection mark "B" confirms that the
equipment is in compliance with the protection
usage requirements of standards PN-93/T-42107
and PN-89/E-06251.
Plassering/Ventilasjon
ADVARSEL:
NÅR DETTE UTSTYRET PLASSERES, MÅ
D U PA S S E P Å AT KO N TA K T E N E F O R
STØMTILFØRSEL ER LETTE Å NÅ.
BSMI Notice (Taiwan Only)
25
Ergonomie Hinweis (nur Deutschland)
China RoHS
Der von uns gelieferte Farbmonitor entspricht den
in der "Verordnung über den Schutz vor Schäden
durch Röntgenstrahlen" festgelegten Vorschriften.
The People's Republic of China released a
regulation called "Management Methods for
Controlling Pollution by Electronic Information
Products" or commonly referred to as China
RoHS. All products including CRT and LCD
monitor which are produced and sold for China
market have to meet China RoHS request.
Auf der Rückwand des Gerätes befindet sich
ein Aufkleber, der auf die Unbedenklichkeit der
Inbetriebnahme hinweist, da die Vorschriften über
dieBauartvonStörstrahlernnachAnlageIII¤5
Abs. 4 der Röntgenverordnung erfüllt sind.
Damit Ihr Monitor immer den in der Zulassung
gefordertenWertenentspricht,istdaraufzu
achten, daß
1. Reparaturen nur durch Fachpersonal
durchgeführt werden.
2. nur original-Ersatzteile verwendet werden.
3. bei Ersatz der Bildröhre nur eine
bauartgleiche eingebaut wird.
Aus ergonomischen Gründen wird empfohlen,
die Grundfarben Blau und Rot nicht auf dunklem
Untergrund zu verwenden (schlechte Lesbarkeit
und erhöhte Augenbelastung bei zu geringem
Zeichenkontrast wären die Folge).
Der arbeitsplatzbezogene Schalldruckpegel nach
DIN 45 635 beträgt 70dB (A) oder weniger.
环保使用期限
ACHTUNG: BEIM AUFSTELLEN
DIESES GERÄTES DARAUF
ACHTEN, DAß NETZSTECKER UND
NETZKABELANSCHLUß LEICHT
ZUGÄNGLICH SIND.
此标识指期限(十年),电子信息产品中含有的
有毒有害物质或元素在正常使用的条件下不
会发生外泄或突变, 电子信息产品用户使用该
电子信息产品不会对环境造成严重污染或对
其人身、 财产造成严重损害的期限.
26
6 Customer care and warranty
Customer Care & Warranty
PLEASE SELECT YOUR COUNTRY/AREA
TO REVIEW DETAILS OF YOUR WARRANTY
COVERAGE
WESTERN EUROPE
Austria / Belgium / Denmark / France /
Germany / Greece / Finland / Ireland / Italy /
Luxembourg / the Netherlands / Norway /
Portugal / Sweden / Switzerland / Spain /
United Kingdom / Poland
EASTERN EUROPE
Czech Republic / Hungary / Russia / Slovakia /
Slovenia / Turkey
LATIN AMERICA
Argentina / Brasil
NORTH AMERICA
Canada / USA
PACIFIC
Australia / New Zealand
ASIA
China / Hong Kong / India / Indonesia / Korea /
Malaysia / Pakistan / Philippines / Singapore /
Taiwan / Thailand / Vietnam
AFRICA
South Africa
MIDDLE EAST
United Arab Emirates
27
F1rst Choice Contact Information
Country
Austria
Belgium
Denmark
Finland
Luxembourg
The Netherlands
Norway
Poland
Portugal
Spain
Sweden
Switzerland
United Kingdom
Code
+43
+32
+45
+358
+352
+31
+47
+48
+351
+34
+46
+41
+44
Telephone number
0810 000206
078 250851
3525 8761
840 320 041
26 84 30 00
0900 0400 063
2270 8250
0223491505
2 1359 1440
902 888 785
08 632 0016
02 2310 2116
0207 949 0069
29
Tariff
€0.07
€0.06
Local call tariff
€0.08
Local call tariff
€0.10
Local call tariff
Local call tariff
Local call tariff
€0.10
Local call tariff
Local call tariff
Local call tariff
CROATIA
Renoprom d.o.o.
Ljubljanska 4,
Sv. Nedjelja,10431
Croatia
Tel: +385 1 333 0974
Consumer Information Centers
Argentina / Australia / Brasil / Canada /
New Zealand / Belarus / Bulgaria / Croatia /
Czech Republic / Estonia / United Arab Emirates /
Hong Kong / Hungary / India / Indonesia /
Israel / Latvia / Lithuania / Malaysia /
Middle East + North Africa / New Zealand /
Pakistan / Romania / Russia /
Serbia & Montenegro / Singapore / Slovakia /
Slovenia / South Africa / South Korea / Taiwan /
Philippines / Thailand / Turkey / Ukraine /
Vietnam
ESTONIA
FUJITSU SERVICES OU
Akadeemia tee 21G
EE-12618 Tallinn
Tel: +372 6519900
www.ee.invia.fujitsu.com
HUNGARY
Serware Szerviz
Vizimolnár u. 2-4
HU - 1031 Budapest
Tel: +36 1 2426331
Email: inbox@serware.hu
www.serware.hu
Eastern Europe
BELARUS Technic al Center of JV IBA
M. Bogdanovich str. 155
BY - 220040 Minsk
Tel: +375 17 217 33 86
BELARUS
Service.BY
Petrus Brovky st. 19 – 101-B
220072, Minsk
Belarus
HUNGARY
Profi Service Center Ltd.
123 Kulso-Vaci Street,
H-1044 Budapest ( Europe Center )
Hungary
Tel: +36 1 814 8080
m.andras@psc.hu
BULGARIA
LAN Service
140, Mimi Balkanska Str.
Office center Translog
1540 Sofia, Bulgaria
Tel: +359 2 960 2360
www.lan-service.bg
LATVIA
ServiceNet LV
Jelgavas iela 36
LV - 1055 Riga,
Tel: +371 7460399
Email: serviss@servicenet.lv
CZECH REPUBLIC
General Consumer Information Center
800 142100
LITHUANIA
ServiceNet LT
Gaiziunu G. 3
LT - 3009 KAUNAS
Tel: +370 7400088
Email: servisas@servicenet.lt
www.servicenet.lt
Xpectrum
Lu.ná 591/4
CZ - 160 00 Praha 6 Tel: 800 100 697 or 220 121
435
Email:info@xpectrum.cz
www.xpectrum.cz
31
TURKEY
Türk Philips Ticaret A.S.
Yukari Dudullu Org.San.Bolgesi
2.Cadde No:22
34776-Umraniye/Istanbul
Tel: (0800)-261 33 02
ROMANIA
Blue Ridge Int'l Computers SRL
115, Mihai Eminescu St., Sector 2
RO - 020074 Bucharest
Tel: +40 21 2101969
SERBIA & MONTENEGRO
Kim Tec d.o.o.
Viline vode bb, Slobodna zona
Beograd L12/3
11000 Belgrade
Serbia
Tel. +381 11 20 70 684
UKRAINE
Comel
Shevchenko street 32
UA - 49030 Dnepropetrovsk
Tel: +380 562320045
www.csp-comel.com LLC Topaz Company
Topaz-Service Company,
Mishina str. 3,
Kiev
Ukraine-03151
Tel: +38 044 245 73 31
SLOVAKIA
General Consumer Information Center
0800004551
Datalan Servisne Stredisko
Puchovska 8
SK - 831 06 Bratislava
Tel: +421 2 49207155
Email: servis@datalan.sk
Latin America
ARGENTINA
Azopardo 1480.
(C1107ADZ) Cdad. de Buenos Aires
Tel: 0800 3330 856
Email: CIC.monitores@Philips.com
SLOVENIA
PC HAND
Brezovce 10
SI - 1236 Trzin
Tel: +386 1 530 08 24
Email: servis@pchand.si
BRASIL
Alameda Raja Gabaglia, 188 - 10°Andar - V.
Olímpia - S. Paulo/SP - CEP 04551-090 Brasil
Tel: 0800-7254101
Email: CIC.monitores@Philips.com
RUSSIA
CPS
18, Shelepihinskaya nab.
123290 Moscow
Russia
Tel. +7(495)797 3434
Pacific
AUSTRALIA
Company: AGOS NETWORK PTY LTD
Address: 4/5 Dursley Road, Yenorra, NSW 2161,
Australia
Tel: 1300 360 386
Fax: +61-2-80808147
Email: philips@agos.com.au
Service hours: Mon.~Fri. 8:00am-7:30pm
Profservice:
14A -3, 2Karacharovskaya str,
109202, Moscow ,
Russia
Tel. +7(095)170-5401
32
Additional service points:
1. Philips Building Jl. Buncit Raya Kav 99. Jakarta Selatan.
Phone: 021-7940040, ext 1722/1724, 98249295, 70980942
NEW ZEALAND
Company: Visual Group Ltd.
Address: 28 Walls Rd Penrose Auckland
Phone: 0800 657447
Fax: 09 5809607
E-mail: vai.ravindran@visualgroup.co.nz
Service Hours: Mon.~Fri. 8:30am~5:30pm
2. Jl. Tanah Abang 1 no 12S. Jakarta Pusat.
Phone: 021-3455150, 34835453
Asia
HONG KONG/Macau
Company Name: PHK Service Limited
Address: Flat A, 10/F., Pak Sun Building, 103 - 107
Wo Yi Hop Road, Kwai Chung, New Territories,
Hong Kong
Tel.: (852) 2610-6908 / (852) 2610-6929 for Hong
Kong and (853) 2856-2277 for Macau
Fax: (852) 2485 3574 for Hong Kong and (853)
2856 1498 for Macau
E-mail: enquiry@phkservice.com.hk
Service Hours: Mon.~Sat. 09:00am~06:00pm
3.
Rukan City Home no H31, Gading Square. Jl. Bulevar Barat. Kelapa Gading. Jakarta Utara. Phone: 021-45870601, 98131424
South Korea
Company: PCS One Korea Ltd.
Address: 112-2, Banpo-dong, Seocho-ku, Seoul,
137-040, Korea
Call Center Tel: 080-600-6600
Tel: 82 2 591 1528
Fax: 82 2 595 9688
E-mail: cic_korea@philips.com
Service hours: Mon.~Fri. 9:00AM~ 6:00PM; Sat.
9:00AM~1:00PM
India
Company: REDINGTON INDIA LTD
Address: SPL Guindy House, 95 Mount Road,
Chennai 600032, India
Tel: +9144-42243352/353
E-mail: aftersales@in.aocmonitor.com
Service hours: Mon.~Fri. 9:00AM~5:30PM; Sat.
9:00AM~1:00PM
Malaysia
Company: After Market Solutions (CE) Sdn Bhd
Address: Lot 6. Jalan 225/51A, 46100 Petaling Jaya,
Selangor DE, Malaysia.
Phone: 603 7953 3370
Philips Info Line: 1-800-880-180
Fax: 603 7953 3338
E-mail: pceinfo.my@philips.com
Service Hours: Mon.~Fri. 8:15am~5:15pm; Sat.
9:00am~1:00pm
Indonesia
Company Name: PT. Gadingsari elektronika Prima
Address: Kompleks Pinang 8, Jl. Ciputat raya No. 8F,
Pondok Pinang. Jakarta
Tel: 021-750909053, 021-750909056
Fax: 021-7510982
E-mail: gepta@cbn.net.id
Service hours: Mon.~Fri. 8:30am~4:30pm;
Sat. 8:30am~2:00pm
Pakistan
Philips Consumer Service
Address: Mubarak manzil, 39, Garden Road, Saddar,
Karachi-74400
Tel: (9221) 2737411-16
Fax: (9221) 2721167
E-mail: care@philips.com
Website: www.philips.com.p
33
Singapore
Company: Philips Electronics Singapore Pte Ltd
(Philips Consumer Care Center)
Address: 620A Lorong 1 Toa Payoh, TP4 Building
Level 1, Singapore 319762
Tel: (65) 6882 3999
Fax: (65) 62508037
E-mail: consumer.care.sg@philips.com
Service hours: Mon.~Fri. 9:00am~6:00pm; Sat.
9:00am~1:00pm
MDR Microware Sales Inc.
Cebu Branch
N. Escario corner Clavano St., Cebu City Phils.
# 255-4415/ 255-3242/253-9361/4124864 to 67
Sun # 0922-8210045 to 46
Taiwan
Company: FETEC.CO
Address: 3F, No.6, Lane 205, Sec. 1, Chang Hsing
Rd, Lu Chu Hs, Taoyuan, Taiwan R.O.C 33800
Consumer Care: 0800-231-099
Tel: (03)2120336
Fax: (03)3129184
E-mail: knlin08@xuite.net
Service hours: Mon.~Fri. 8:30am~7:00pm
CDO Office:
1445 Corrales Ext.,CDO City
088-856-8540/856-8541
Sun # 0922-8210080
Thailand
Company: Axis Computer System Co., Ltd.
Address: 1421 Soi Lardprao 94, Srivara Town In
Town Soi 3 Road, Wangthonglang, Bangkok 10310
Thailand
Tel: (662) 934-5498
Fax: (662) 934-5499
E-mail: axis5@axiscomputer.co.th
Service Hours: Mon.~Fri. 08:30am~05:30pm
Africa
SOUTH AFRICA
Company name: Sylvara Technologies Pty Ltd
Address: Ho Address Palm Springs Centre
Christoffel Road Van Riebeeck Park Kempton Park,
South Africa
Tel: +27878084456
Fax: +2711 391 1060
E-mail: customercare@philipssupport.co.za
Service hours: Mon.~ Fri. 08:00am~05:00pm
Davao Office:
C. Arellano St., Davao City 8000
082- 225-3021/225-3022
Sun# 0922-8210015
Iloilo Office:
C. Lim Comp., Gomez St., Iloilo City
# 033 338-4159/ 033 508-3741
Sun # 0922-8808850
Glee Electronics Inc
Contact nos. (632) 636-3636 / 7064028 to 29
Fax no. (632) 7064026
Middle East
Middle East + North Africa
Company: AL SHAHD COMPUTER L.L.C
Address: P.O.BOX: 29024, DUBAI, UNITED ARAB
EMIRATES
TEL: 00971 4 2276525
FAX: 00971 4 2276242
E-mail: shahd52@eim.ae
Service hours: Sat.~Thur. 9:00am~1:00pm &
4:00pm- 8:00pm
Receiving Centers
NEO CARE - Megamall
4th Level Cyberzone, Building B,
SM Megamall, Mandaluyong City
NEO CARE - SM North EDSA
4th Level Cyberzone, Annex Bldg.
SM City North EDSA, Quezon City
441-1610
34
AUTO button doesn't function
• The auto function is applicable only in
VGA-Analog mode. If the result is not satisfactory, you can do manual adjustments via the OSD menu.
7 Troubleshooting & FAQs
7.1Troubleshooting
This page deals with problems that can be
corrected by a user. If the problem still persists
after you have tried these solutions, contact Philips
customer service representative.
Note
The Auto Function is not applicable in
DVI-Digital mode as it is not necessary.
Visible signs of smoke or sparks
• Do not perform any troubleshooting steps
• Disconnect the monitor from mains power source immediately for safety
• Contact with Philips customer service representative immediately.
Common Problems
No Picture (Power LED not lit)
• Make sure the power cord is plugged into the power outlet and into the back of the monitor.
• First, ensure that the power button on the front of the monitor is in the OFF position, then press it to the ON position.
Imaging Problems
Image is not centered
• Adjust the image position using the “Auto” function in OSD Main Controls.
• Adjust the image position using the Phase/
Clock of Setup in OSD Main Controls. It is valid only in VGA mode.
No Picture (Power LED is Green)
• Make sure the computer is turned on.
• Make sure the signal cable is properly connected to your computer.
• make sure the monitor cable has no bent pins on the connect side. If yes, repair or replace the cable.
• The Energy Saving feature may be activated
Image vibrates on the screen
• Check that the signal cable is properly securely
connected to the graphics board or PC.
Screen says
Vertical flicker appears
•
•
•
•
•
Make sure the monitor cable is properly connected to your computer. (Also refer to the Quick Set-Up Guide).
Check to see if the monitor cable has bent pins.
Make sure the computer is turned on.
39
Adjust the image using the “Auto” function in OSD Main Controls.
Eliminate the vertical bars using the Phase/
Clock of Setup in OSD Main Controls. It is valid only in VGA mode.
Horizontal flicker appears
•
•
Green, red, blue, dark, and white dots appears on
the screen
• The remaining dots are normal characteristic of the liquid crystal used in today’s technology, Please refer the pixel policy for more detail.
Adjust the image using the “Auto” function in OSD Main Controls.
Eliminate the vertical bars using the Phase/
Clock of Setup in OSD Main Controls. It is valid only in VGA mode.
The "power on" light is too strong and is
disturbing
• You can adjust “power on” light using the power LED Setup in OSD main Controls.
Image appears blurred, indistinct or too dark
• Adjust the contrast and brightness on
On-Screen Display.
Audio problem
No sound
• Check if audio cable is connected to PC and monitor correctly.
• Ensure audio is not muted. Press OSD “Menu”, select “Audio” then “Mute”. Check it on “Off ” position.
• Press “Volume” in OSD main control to adjust the volume.
An "after-image", "burn-in" or "ghost image"
remains after the power has been turned off.
• Uninterrupted display of still or static images over an extended period may cause " burn in", also known as "after-imaging " or "ghost imaging", on your screen. "Burn-in", "after-
imaging", or "ghost imaging" is a well-known phenomenon in LCD panel technology. In most cases, the "burned in" or "after-imaging"
or "ghost imaging" will disappear gradually over a period of time after the power has been switched off.
• Always activate a moving screen saver
program when you leave your monitor unattended.
• Always activate a periodic screen refresh application if your LCD monitor will display unchanging static content.
• Severe” burn-in” or “after-image” or “ghost image” symptoms will not disappear and cannot be repaired. The damage mentioned above is not covered under your warranty.
For further assistance, refer to the Consumer
Information Centers list and contact Philips
customer service representative.
Image appears distorted. Text is fuzzy or blurred.
• Set the PC’s display resolution to the same mode as monitor’s recommended screen native resolution.
40
7.2SmartControl Lite FAQs
Q1.
I change the monitor on a PC to a different one and the SmartControl Lite becomes un-usable, what do I do?
Q3. After installing SmartControl Lite, when clicking on SmartControl Lite tab, nothing shows up after a while or a failure message shows, what happened?
Ans.:It might be your graphic adaptor is not compatible with the SmartControl Ans.:Restart your PC and see if SmartControl Lite. If your graphic adaptor is one
Lite can work. Otherwise, you will of the above mentioned brands, try to need to remove and re-install SmartControl download the most updated graphic adaptor
Lite to ensure proper driver is installed.
driver from corresponding companies’ web site. Q2. The SmartControl Lite functions Install the driver. Remove SmartControl worked well before, but it does not work Lite, and re-install it once more.
anymore, what can I do?
If it is still not working, we are sorry that the graphic adaptor is not supported. Please Ans.:If the following actions were executed, visit Philips website and check if an updated the monitor driver may need to be
SmartControl Lite driver is available.
re-installed.
•Changed video graphic adapter to another Q4. When I click on Product Information, one
only partial information is shown, what •Updated video driver
happened?
•Activities on OS, such as service pack or patch
Ans.:It might be your graphic card adaptor driver •Run Windows Update and updated is not the most updated version which fully monitor and/or video driver
supporting DDC/CI interface. Please try to •Windows was booted with the monitor download the most updated graphic power off or disconnected.
adaptor driver from corresponding To find out, please right click My
companies’ web site. Install the driver. Computer and click on Properties-
Remove SmartControl Lite and
>Hardware-> Device Manager.
re-install it once more.
If you see "Plug and Play Monitor" shows under Monitor, then you need to re-install. Simply remove SmartControl Lite and re-install it.
Q5. I forgot my PIN for Theft Deterrence Function. How can I do?
Ans.: Philips Service center has a right to ask for legitimate identification and authorization, in order to establish ownership of the monitor.
41
Q3: What are the .inf and .icm files on the CD-ROM? How do I install the drivers (.inf and .icm)?
7.3General FAQs
Q1: When I install my monitor what should I do if the screen shows 'Cannot display this Ans.:These are the driver files for your monitor. video mode'?
Follow the instructions in your user manual Ans.:Recommended resolution for Philips 18.5": to install the drivers. Your computer may ask you for monitor drivers (.inf and .icm 1366 x 768 @60Hz.
•Unplug all cables, then connect your PC to files) or a driver disk when you first install your monitor. Follow the instructions to the monitor that you used previously.
•In the Windows Start Menu, select Settings/ insert the ( companion CD-ROM) included Control Panel. In the Control Panel Window, in this package. Monitor drivers (.inf and .icm files) will be installed automatically.
select the Display icon. Inside the Display
Control Panel, select the 'Settings' tab. Q4: How do I adjust the resolution?
Under the setting tab, in box labeled
'desktop area', move the sidebar to Ans.:Your video card/graphic driver and monitor 1366 x 768 pixels (18.5").
together determine the available resolutions. •Open 'Advanced Properties' and set the You can select the desired resolution under Refresh Rate to 60Hz, then click OK.
Windows® Control Panel with the "Display •Restart your computer and repeat step
properties".
2 and 3 to verify that your PC is set at 1366 x 768@60Hz (18.5").
•Shut down your computer, disconnect your Q5: What if I get lost when I am making monitor adjustments via OSD?
old monitor and reconnect your Philips LCD monitor.
Ans.:Simply press the OK button, then select •Turn on your monitor and then turn on 'Reset' to recall all of the original factory your PC.
settings.
Q2: What does the recommended refresh Q6: Is the LCD screen resistant to scratches?
rate for LCD monitor?
Ans.:Recommended refresh rate in LCD monitors is 60Hz, In case of any disturbance on screen, you can set it up to 75Hz to see if that removes the disturbance.
Ans.:In general it is recommended that the panel surface is not subjected to excessive shocks and is protected from sharp or blunt objects. When handling the monitor, make sure that there is no pressure or force applied to the panel surface side. This may affect your warranty conditions.
Q7: How should I clean the LCD surface?
Ans.:For normal cleaning, use a clean, soft cloth. For extensive cleaning, please use isopropyl alcohol. Do not use other solvents such as ethyl alcohol, ethanol, acetone, hexane, etc.
42
sales representative for more information.
Q10: Can I connect my LCD monitor to any PC, workstation or Mac?
Q8: Can I change the color setting of my monitor?
Ans.:Yes, you can change your color setting through OSD control as the following procedures,
•Press "OK" to show the OSD (On Screen Display) menu
•Press "Down Arrow" to select the option "Color" then press "OK" to enter color setting, there are three settings as below.
1. Color Temperature; The six settings are 5000K, 6500K, 7500K, 8200K, 9300K and 11500K. With settings in the 5000K range the panel appears ‘warm,' with a
red-white color tone, while a 11500K temperature yields ‘cool, blue-white toning."
2. sRGB; this is a standard setting for ensuring correct exchange of colors between different device (e.g. digital cameras, monitors, printers, scanners, etc)
3. User Define; the user can choose
his/her preference color setting by adjusting red, green blue color.
Note:
A measurement of the color of light radiated by an object while it is being heated. This measurement is expressed in terms of absolute scale, (degrees Kelvin). Lower Kevin temperatures such as 2004K are red; higher temperatures such as 9300K are blue. Neutral temperature is white, at 6504K.
Q9: Can the Philips LCD Monitor be mounted
on the wall?
Ans.:Yes. Philips LCD monitors have this optional feature. Four standard VESA mount holes on the rear cover allows the user to mount the Philips monitor on most of the VESA standard arms or accessories. We recommend you to contact your Philips 43
Ans.:Yes. All Philips LCD monitors are fully
compatible with standard PCs, Macs and workstations. You may need a cable adapter to connect the monitor to your Mac
system. Please contact your Philips sales representative for more information.
Q11: Are Philips LCD monitors
Plug-and- Play?
Ans.:Yes, the monitors are Plug-and-Play compatible with Windows 7/Vista/XP/NT, Mac OSX, Linux
Q12: What kind of wide-angle technology is available?
Ans.:Currently, the IPS type panels offer the best Contrast Ratio, compared to MVA,
or PVA technologies. TN panels have improved over the years, but IPS panel still gives superior results over TN panel.
Q13: What is Image Sticking, or Image Burn-in, or After Image, or Ghost Image in LCD panels?
Ans.:Uninterrupted display of still or static images over an extended period may cause
"burn in", also known as "after-imaging" or "ghost imaging", on your screen. "Burn-in",
"after-imaging", or "ghost imaging" is a
well-known phenomenon in LCD panel
technology. In most cases, the "burned in" or
"atter-imaging" or "ghost imaging" will
disappear gradually over a period of time
after the power has been switched off.
Always activate a moving screen saver
program when you leave your monitor unattended.
Always activate a periodic screen refresh application if your LCD monitor will display unchanging static content.
Warning
Severe"burn-in" or "after-image" or
"ghost image" symptoms will not disappear and cannot be repaired. The damage mentioned above is not covered under your warranty.
Q14: Why is my Display not showing sharp text,
and is displaying jagged characters?
Ans.:Your LCD monitor works best at its native resolution of 1366 x 768@60Hz. For best display please use this resolution.
44
2010 © Koninklijke Philips Electronics N.V. All rights reserved.
Philips and the Philips Shield Emblem are registered trademarks of
Koninklijke Philips Electronics N.V. and are used under license from
Koninklijke Philips Electronics N.V.
Specifications are subject to change without notice.
Version: M2191VE1T
45
Download PDF