Philips DVD player with HDMI and USB DVP3388/94 User manual

Philips DVD player with HDMI and USB DVP3388/94 User manual
Register your product and get support at
www.philips.com/welcome
DVP3388
User manual
dvp3388_94_en.indd 1
2/19/2009 6:13:13 PM
2
dvp3388_94_en.indd 2
2/19/2009 6:13:14 PM
Contents
Safety and important notice
Trademark Notice
2 Your DVD player
Features highlight
Product overview
3 Connect
Connect video cables
Connect audio cables
Route audio to other devices
Connect USB device
Connect to power outlet
4 Get started
Prepare the remote control
Find the correct viewing channel
Select menu display language
Turn on Progressive Scan
Use Philips EasyLink
5 Play
Play from disc
Play video
Play music
Play photo
Play from USB device
25
Media copy
Create MP3 files
25
25
7 Adjust settings
27
General setup
Audio setup
Video setup
Preferences
27
28
31
33
4
4
5
6
6
7
9
9
10
11
12
12
13
8 Additional information
Update software
Care
Contents
1 Important
6 Advanced features
36
36
36
9 Specification
37
10 Troubleshooting
39
11 Glossary
41
13
14
14
15
16
17
17
18
21
23
24
3
dvp3388_94_en.indd 3
2/19/2009 6:13:14 PM
1 Important
Safety and important notice
Warning
• Risk of overheating! Never install the DVD player
•
•
•
•
•
•
in a confined space. Always leave a space of at least
four inches around the DVD player for ventilation.
Ensure the curtains or other objects never cover the
ventilation slots on the DVD player.
Never place the DVD player, remote control or
batteries near naked flames or other heat sources,
including direct sunlight.
Only use this DVD player indoors. Keep this DVD
player away from water, moisture and liquid-filled
objects.
Never place this DVD player on other electrical
equipment.
Keep away from this DVD player during lightning
storms.
Where the mains plug or an appliance coupler is
used as the disconnect device, the disconnect device
shall remain readily operable.
Visible and invisible laser radiation when open. Avoid
exposure to beam.
About Progressive Scan
Recycle notice
This electronic equipment contains a large
number of materials that can be recycled or
reused if disassembled by a specialized
company. If you are disposing of an old
machine, please take it to a recycling center.
Please observe the local regulations regarding
disposal of packaging materials, exhausted
batteries and old equipment.
Copyright notice
This product incorporates copyright protection
technology that is protected by method claims
of certain U.S. patents and other intellectual
property rights owned by Macrovision
Corporation and other rights owners. Use of
this copyright protection technology must be
authorised by Macrovision Corporation, and is
intended for home and other limited viewing
uses only unless otherwise authorised by
Macrovision Corporation. Reverse engineering
or disassembly is prohibited.
Consumers should note that not all high
definition television sets are fully compatible
with this product and may cause artifacts to be
displayed in the picture. In case of 525 or 625
progressive scan picture problems, it is
recommended that the user switch the
connection to the ‘standard definition’ output. If
there are questions regarding our TV set
compatibility with this model 525p and 625p
DVD player, please contact our customer
service center.
4
dvp3388_94_en.indd 4
2/19/2009 6:13:14 PM
Trademark Notice
HDMI, and HDMI logo and High-Definition
Multimedia Interface are trademarks or
registered trademarks of HDMI licensing LLC.
Important
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol
are trademarks of Dolby Laboratories.
Windows Media and the Windows logo are
trademarks, or registered trademarks of
Microsoft Corporation in the United States and/
or other countries.
DivX, DivX Ultra Certified, and associated
logos are trademarks of DivX, Inc. and are used
under license.
Official DivX® Ultra Certified product.
Plays all versions of DivX ® video (including
DivX ® 6) with enhanced playback of DivX®
media files and the DivX® Media Format.
Plays DivX® video with menus, subtitles and
audio tracks.
The USB-IF Logos are trademarks of Universal
Serial Bus Implementers Forum, Inc.
5
dvp3388_94_en.indd 5
2/19/2009 6:13:14 PM
2 Your DVD
player
Screen fit
View the movie in full screen on any TV with
this DVD player.
Congratulations on your purchase, and
welcome to Philips! To fully benefit from the
support that Philips offers, register your product
at www.philips.com/welcome.
Hi speed USB 2.0 link
Simply plug your USB flash drive into the USB
jack to play your MP3/WMA/JPEG/DivX/WMV
files to enjoy the music play in superb sound
quality.
This DVD player offers higher picture quality
video play for an amazing viewing experience.
Features highlight
Video upscaling to 1080p
You can now watch the DVDs in the highest
picture quality available for your HDTV. This
DVD player offers full high-definition video play
up to 1080p resolution for an amazing viewing
experience. A highly detailed picture and
increased sharpness delivers a more true-to-life
picture.
EasyLink
EasyLink uses the HDMI CEC (Consumer
Electronics Control) industry standard protocol
to share functionality with all HDMI CEC
compliant devices over HDMI. It enables the
connected devices to control each other with a
single remote control.
Media copy
You can transfer data files such as MP3, WMA
and JPEG from disc to USB flash drive.
Create MP3 files
Convert your favourite audio tracks from an
audio CD into MP3 format. The created MP3
files are saved in your USB device.
Region codes
Your DVD player plays discs with the following
region codes.
DVD region code
Countries
India
ALL
Note
• EasyLink (HDMI CEC) is only applicable with certain
•
criteria. Terms and conditions may vary by product.
Consult your product dealer for information.
Philips does not guarantee 100% interoperability
with all HDMI CEC devices.
6
dvp3388_94_en.indd 6
2/19/2009 6:13:14 PM
Product overview
Remote control
Main unit
1
3
Your DVD player
2
18
4
17
5
1
2
3
4
5
6
16
6
7
15
14
a 2 (Standby-on)
• Turn on the DVD player or switch to
standby mode.
8
9
13
10
12
b Disc compartment
11
c Display panel
d Z (Open/Close)
• Open or close the disc compartment.
e u (Play/Pause)
• Start, pause or resume disc play.
f
(USB) jack
• Connect a USB flash drive.
a 2 (Standby-On)
• Turn on the DVD player or switch to
standby mode.
b Z (Open/Close)
• Open or close the disc compartment.
c DISC MENU
• Access or exit the disc menu.
• Switch to disc mode.
• For VCD/SVCD, turn PBC (Playback
Control) on or off in PBC mode.
7
dvp3388_94_en.indd 7
2/19/2009 6:13:14 PM
d v V b B (Navigation buttons)
• Navigate through the menus.
• Toggle between various repeat modes.
• Search fast-forward (B) or fastbackward (b). Press repeatedly to
change the search speed.
• Mark the section for repeat play, or turn
off repeat mode.
• Search slow-forward (v) or slowbackward (V). Press repeatedly to
change the search speed.
e
l REPEAT/REPEAT A-B
BACK
m AUDIO/CREATE MP3
• Select an audio language/channel.
• Access the menu to create MP3.
n x (Stop)
• Stop disc play.
• Return to the previous display menu.
• For DVD, navigate to the title menu.
• For VCD version 2.0 or SVCD with
PBC turned on, return to the menu.
f í/ë (Previous/Next)
• Skip to the previous or next title,
chapter, or track.
• Press and hold for fast-backward or
fast-forward search.
g
(USB)
• Switch to USB mode and display the
content.
h Numeric buttons
o u (Play/Pause)
• Start, pause or resume disc play.
p
INFO
• For disc, display the current status or
disc information.
• For slideshows, display a thumbnail view
of photo files.
q OK
• Confirm an entry or selection.
r SETUP
• Access or exit the setup menu.
• Select an item to play.
i SUBTITLE
• Select DVD or DivX subtitle language.
• Access the menu to USB copy or USB
delete.
j , ZOOM
• Fit the picture format to the TV screen.
• Zoom in or out of the picture.
k VOLUME
• Display the current volume level and
use (b) or (B) navigation buttons to
set the volume level between 0 ~ 20.
8
dvp3388_94_en.indd 8
2/19/2009 6:13:14 PM
Make the following basic connections to use the
DVD player.
Basic connections:
• Video cables
• Audio cables
Select the best video connection that the TV can
support.
• Option 1: Connect to HDMI jack (for a
HDMI, DVI or HDCP-compliant TV).
• Option 2: Connect to component video
jacks (for a standard TV or Progressive Scan
TV).
• Option 3: Connect to video (CVBS) jack
(for a standard TV).
Optional connections:
• Audio to other devices:
• Multi channel receiver
Connect
3 Connect
Note
• You must connect this DVD player directly to a
TV.
• Digital amplifier/receiver
• Analog stereo system
Option 1: Connect to HDMI jack
Note
• Refer to the type plate at the rear or bottom of the
product for identification and supply ratings.
• Before you make or change any connections, ensure
that all the devices are disconnected from the power
outlet.
HDMI IN
HDMI OUT
Tip
• Different types of connectors may be used to
connect this product to your TV, depending on
availability and your needs. A comprehensive
interactive guide to help you connect your product is
available at www.connectivityguide.philips.com.
1
Connect a HDMI cable (not supplied) to
the HDMI OUT jack on this DVD player
and the HDMI input jack on the TV.
• Use a HDMI-DVI adaptor in case the
TV has only a DVI connection.
Connect video cables
Connect this DVD player to the TV to view
disc play.
Note
• If the device supports HDMI CEC, you can control
compliant devices with a single remote control (see
chapter ‘Use Philips EasyLink’).
Tip
• This type of connections provide best picture quality.
9
dvp3388_94_en.indd 9
2/19/2009 6:13:14 PM
Option 2: Connect to component
video jacks
Option 3: Connect to video (CVBS)
jack
VIDEO IN
Pb
Y
Pr
COMPONENT VIDEO OUT
Pr
Pb
Y
COMPONENT
VIDEO IN
1
1
Connect the component video cables (not
supplied) to the Y Pb Pr jacks on this DVD
player and the component video input
jacks on the TV.
• If a progressive scan TV is used, you
may turn on the progressive scan mode
(see chapter ‘Turn on Progressive Scan’
for details).
Connect a composite video cable
(supplied) to the TV OUT jack on this
DVD player and the video input jack on
the TV.
Tip
• The video input jack on the TV may be labeled as
A/V IN, VIDEO IN, COMPOSITE or BASEBAND.
• This type of connection provides standard picture
quality.
Tip
• The component video input jacks on the TV may be
labeled as Y Pb/Cb Pr/Cr or YUV.
• This type of connection provides good picture
quality.
Connect audio cables
Connect the audio from this DVD player to the
TV to allow sound output through the TV.
AUDIO IN
FRONT L
FRONT R
1
Connect the audio cables (supplied) to the
AUDIO OUT FRONT L/R jacks on this
DVD player and the audio input jacks on
the TV.
10
dvp3388_94_en.indd 10
2/19/2009 6:13:14 PM
Route audio to other devices
Connect to digital amplifier/receiver
Route the sound from this DVD player to other
devices to enhance audio play.
DIGITAL AUDIO
INPUT
Connect
OPTICAL COAXIAL
Connect to multi channel receiver
COAXIAL
OPTICAL
MULTI CHANNEL
AUDIO IN
FRONT L REAR L CENTER
1
FRONT R REAR R SUBWOOFER
or
FRONT L REAR L CENTER
FRONT R REAR R SUBWOOFER
1
Connect the audio cables (not supplied) to
the AUDIO OUT (FRONT L/R, REAR
L/R, CENTER and SUBWOOFER) jacks
on this DVD player and the audio input
jacks on the device.
Connect a coaxial cable (not supplied) to
the COAXIAL jack on this DVD player
and the DIGITAL IN (COAXIAL) jack on
the device.
1
Connect an optical cable (not supplied) to
the OPTICAL jack on this DVD player and
the DIGITAL IN (OPTICAL) jack on the
device.
Tip
• You can optimize the audio output (see chapter
‘Adjust settings’ - [ Audio Setup ] > [ Digital Audio
]) for details.
Tip
• You can optimize the audio output (see chapter
‘Adjust settings’ - [ Audio Setup ] > [ Analog Output
]) for details.
11
dvp3388_94_en.indd 11
2/19/2009 6:13:14 PM
Connect to analog stereo system
Connect USB device
AUDIO IN
FRONT L
FRONT R
1
Connect the audio cables (supplied) to the
AUDIO OUT FRONT L/R jacks on this
DVD player and the audio input jacks on
the device.
Tip
• You can optimize the audio output (see chapter
‘Adjust settings’ - [ Audio Setup ] > [ Analog Output
]) for details.
1
Connect the USB flash drive to the
(USB) jack on this DVD player.
Note
• This DVD player can only play/view MP3, WMA,
•
DivX, JPEG or WMV files that are stored on such
devices.
to access the content and play the files.
Press
Connect to power outlet
Warning
• Risk of product damage! Ensure that the power
supply voltage corresponds to the voltage printed on
the back or the underside of the DVD player.
1
Connect the power cord to the power
outlet.
The DVD player is ready to be set up
for use.
12
dvp3388_94_en.indd 12
2/19/2009 6:13:14 PM
4 Get started
Navigate through the menu
1
Point the remote control directly at the
remote sensor on this DVD player and
select the desired function.
1
2
3
Push to open the battery compartment
cover.
Insert two R03 or AAA batteries type with
correct polarity (+/-) as indicated.
Close the battery compartment.
Get started
Prepare the remote control
2
Use the following buttons on the remote
control to navigate through the on-screen
menus.
Button
vV
Action
Move up or down.
bB
Move left or right.
OK
Confirm a selection.
Caution
• Remove batteries if they are exhausted or if the
remote control is not to be used for a long time.
• Do not mix batteries (old and new or carbon and
alkaline, etc.).
Enter numbers.
• Batteries contain chemical substances, they should
be disposed of properly.
13
dvp3388_94_en.indd 13
2/19/2009 6:13:14 PM
Find the correct viewing
channel
Select menu display language
Note
1
2
Press 2 to turn on the DVD player.
• You can skip this setting if this DVD player is
connected to a HDMI CEC compliant TV. It switches
automatically to the same OSD menu language as
per your TV setting.
Turn on the TV and switch to the correct
video-in channel.
• You may go to the lowest channel on
the TV, then press the Channel Down
button on the TV remote control until
you see the Video In channel.
• You may press ° button repeatedly
on the TV remote control.
1
2
Press SETUP.
[ General Setup ] menu is displayed.
Select [ OSD Language ], then press B.
General Setup
• Usually this channel is between the
lowest and highest channels and may
be called FRONT, A/V IN, VIDEO, etc..
Disc Lock
Auto (Eng)
OSD Language
English
Sleep Timer
Auto Standby
Tip
DivX(R) VOD Code
• See the TV user manual on how to select the correct
input on the TV.
• If the audio output of this DVD player is routed
to other audio device (such as audio system
or receiver), turn on the audio device to the
appropriate audio input channel. Refer to the device
user manual for details.
• The language options are different
depending on your country or region.
It may not correspond to the illustration
shown here.
3
Press vV to select a language, then press
OK.
Tip
• You can set the default language for DVD audio
and disc menu, see chapter ‘Adjust settings’ - [
Preferences ] for details.
14
dvp3388_94_en.indd 14
2/19/2009 6:13:14 PM
Connect a progressive scan TV with
component video jacks (see chapter ‘Connect
video cables - Option 2: Connect to
component video jacks’ for details).
1
2
3
4
7
You can now turn on the progressive scan
mode on the TV (see the TV user manual).
Note
• The progressive scan setting will not be available
when the HDMI video signal is detected.
• During play, when progressive scan mode is on for
Turn on the TV to the correct viewing
channel for this DVD player.
both this DVD player and the TV, distorted picture
may display. Turn off the progressive scan feature on
both this DVD player and the TV.
Press SETUP.
Get started
Turn on Progressive Scan
Press V to select [ Video Setup ].
Select [ Progressive ] > [ On ], then press
OK.
A warning message is displayed.
Video Setup
TV System
On
TV Display
Progressive
Off
Picture Setting
HD JPEG
HDMI Setup
5
To proceed, select [ OK ] and press OK.
The progressive setup is complete.
Note
• If a blank/distorted screen is displayed, wait for 15
seconds for the auto recover.
• If no picture displayed, turn off the progressive scan
mode as follows:
1) Press Z to open the disc compartment.
2) Press the numeric button ‘1’.
6
To exit the menu, press SETUP.
15
dvp3388_94_en.indd 15
2/19/2009 6:13:14 PM
Use Philips EasyLink
The DVD player supports Philips EasyLink,
which uses the HDMI CEC (Consumer
Electronics Control) protocol. EasyLinkcompliant devices that are connected through
HDMI connectors can be controlled by a single
remote control.
Philips does not guarantee 100% interoperability
with all HDMI CEC devices.
1
2
Turn on the HDMI CEC operations on the
TV and other connected devices. See TVs/
devices manual for details.
You can now enjoy the following Philips
EasyLink controls.
One-touch play
When you press the STANDBY button, it turns
on the TV and this DVD player, then video disc
play starts.
• To enable One-touch play, a video disc
must be placed in the disc compartment
before operation.
One-touch standby
When you press and hold the STANDBY button,
all connected HDMI CEC devices switch to
standby mode simultaneously.
Tip
• The default setting for EasyLink features is on. You
can change the default setting, see chapter ‘Adjust
settings’ - [ Video Setup ] > [ HDMI Setup ] > [
EasyLink Setup ] for details.
16
dvp3388_94_en.indd 16
2/19/2009 6:13:14 PM
5 Play
Tip
• If the password entry menu is displayed, you have to
enter the password before it can be played.
• If you pause or stop a disc for about 5 minutes, the
•
Play
Play from disc
screen saver activates. To deactivate the screen
saver, press DISC MENU.
After you pause or stop a disc, if no buttons
are pressed within 15 minutes, this DVD player
automatically switches to standby mode.
Note
• DVDs and DVD players are designed with regional
•
•
•
restrictions. Ensure that the DVD video you play is
for the same region zone as the player (indicated on
its back).
This DVD player can support play of the following
file formats: MP3/WMA/JPEG/DivX/WMV.
About WMV 9 - this DVD player only supports Main
Profile (low level) and Simple Profile. Advanced
Profile and DRM-protected video files are not
supported.
To play DVD-R, DVD+R or DVD-RW, the disc must
be finalized.
Play a disc
Caution
• Never place any objects other than discs into the
disc compartment.
1
2
Press Z to open the disc compartment.
Insert a disc with its label facing up.
• For double-sided disc, load the side to
play faces up.
3
Press Z to close the disc compartment
and start disc play.
• To view disc play, turn on the TV to
the correct viewing channel for this
DVD player.
4
To stop disc play, press x.
17
dvp3388_94_en.indd 17
2/19/2009 6:13:14 PM
Play video
Change video play
Note
• For video disc, play always resumes from the point
where it was last stopped. To start play from the
1
2
Play a title.
Use the remote control to change the
video play.
beginning, press í while the message is displayed.
Control a title
1
2
Button
Action
AUDIO/
CREATE MP3
Change audio language.
• Only applicable to discs
with multiple audio
language or channel.
SUBTITLE
Change subtitle language.
• Only applicable to discs
with multiple subtitle
language.
REPEAT/
REPEAT A-B
Selects or turns off repeat
mode.
• To select a repeat play
mode, press b B.
• Repeat options vary
depending on the disc
type.
• For VCD/SVCD, repeat
play is only possible if the
PBC mode is turned off.
, ZOOM
(Screen Fit)
Fit the picture format to the
TV screen.
• Press repeatedly until the
image is scaled to fi t to
the TV screen.
, ZOOM
Toggle between screen
aspect ratio and different
zoom factor.
• To pan through the
zoomed image, press the
navigation buttons.
INFO
Display the current status or
disc information.
• You can change the video
play options here without
interrupting disc play.
Play a title.
Use the remote control to control the title.
Button
Action
u
Start, pause or resume disc
play.
x
Stop disc play.
ë
Skip to the next title or
chapter.
í
Skip to the beginning of the
current title or chapter.
• Press twice to jump to the
previous title or chapter.
m, M
Searches fast-forward (M)
or fast-backward (m).
• Press repeatedly to change
the search speed.
v, V
Searches slow-forward (v) or
slow-backward (V).
• Press repeatedly to change
the search speed.
• For VCD/SVCD, slowbackward search is not
possible.
18
dvp3388_94_en.indd 18
2/19/2009 6:13:14 PM
Note
Preview disc contents
• Some operations may not work with some discs. See
the information accompanying the disc for details..
Play
Access DVD menu
1
2
1
2
Press DISC MENU to access disc main
menu.
Select Digest Type:
Title Digest
• In some menus, press the numeric
buttons to input your selection.
Chapter Digest
Title Interval
• To return to the title menu during play,
press BACK.
Chapter Interval
VCD/SVCD
Select Digest Type:
The PBC (Playback Control) for VCD/SVCD is
turned on by default in the factory. When you
load in a VCD/SVCD, the contents menu is
displayed.
1
Press numeric buttons to select a play
option, then press OK to start play.
• If PBC is off, it skips the menu and starts
play from the first track.
• During play, you can press BACK to
return to the menu (if the PBC mode is
on).
Select [ Preview ], then press B.
DVD
Select a play option, then press OK.
Access VCD menu
During play, press
INFO.
The disc status menu is displayed.
Track Digest
Disc Interval
Track Interval
3
Select a preview option, then press OK.
A six thumbnails preview screen is
displayed.
• To go to the next/previous preview
screen, press í/ë.
• To start play, press OK at the selected
thumbnail picture.
Tip
• The default setting for PBC is on. You can change the
default setting, see chapter ‘Adjust settings’ [ Preferences ] > [ PBC ] for details.
19
dvp3388_94_en.indd 19
2/19/2009 6:13:14 PM
Quick skip play to a specific time
View DVD play from different angles
1
1
2
During play, press
INFO.
The disc status menu is displayed.
Select the current elapsed playing time,
then press B.
• [ TT Time ] (title time)
2
3
• [ CH Time ] (chapter time)
During play, press
INFO.
The disc status menu is displayed.
Select [ Angle ], then press B.
Press the numeric buttons to change the
angle.
Play changes to the selected angle.
• [ Disc Time ] (disc time)
• [ Track Time ] (track time)
3
Press the numeric buttons to change the
time where you want to skip to.
Display play time
1
2
• Only applicable to discs contain sequences recorded
from different camera angles.
Set repeat play for a specific section
During play, press
INFO.
The disc status menu is displayed.
1
Select [ Time Disp ], then press B.
The display options are different
depending on the disc type.
2
Option
Action
[ Title Elapsed ] Display DVD title or chapter
/ [ Chapter
elapsed play time.
Elapsed ]
[ Title Remain ] Display DVD title or chapter
/ [Chapter
remaining play time
Remain ]
[ Total Elapsed
] / [Single
Elapsed ]
Display VCD/SVCD disc or
track elapsed play time.
[ Total Remain
] / [Single
Remain ]
Display VCD/SVCD disc or
track remaining play time.
3
Note
During play, press REPEAT/REPEAT A-B
repeatedly until [ K A ] appears at
where you want to set the starting point.
Press REPEAT/REPEAT A-B repeatedly
again until [ K AB ] appears to set the
ending point.
Repeat play starts.
3
To cancel repeat play, press REPEAT/
REPEAT A-B repeatedly until [ Off ]
appears.
Note
• The marked section for repeat play is only possible
within a track/title.
Select an option, then press OK.
20
dvp3388_94_en.indd 20
2/19/2009 6:13:14 PM
DivX video is a digital media format that retains
high quality despite a high rate of compression.
This DVD player is DivX® Certified so that
you can enjoy DivX video.
1
Note
• For some commercial audio disc, play may resume
from the point where it was last stopped. To start
play from first track, press í.
Insert a disc or USB that contains the DivX
videos.
• For USB, press
.
A contents menu is displayed.
2
3
Play music
Select a title to play, then press OK.
Use the remote control to control the
title.
Play
Play DivX® video
Control a track
1
2
Play a track.
Use the remote control to control the
track.
Button
Action
Button
Action
SUBTITLE
Change subtitle language.
u
AUDIO/
CREATE MP3
Change audio language/
channel.
Start, pause or resume disc
play.
x
Stop disc play.
x
Stop disc play.
• For DivX, the contents
menu is displayed.
• For DivX Ultra video,
press this button again
to display the contents
menu.
ë
Skip to the next track.
í
Skip to the beginning of the
current track. Press twice to
jump to the previous track.
INFO
• Display title elapsed play
time or title remaining
play time.
• Display DivX Ultra video
information.
Select an item to play.
m, M
Searches fast-forward (M)
or fast-backward (m).
• Press repeatedly to change
the search speed.
REPEAT/
REPEAT A-B
Toggle through various repeat
play mode; or turn off repeat
mode.
• Repeat options vary
depending on the disc type.
Note
• You can only play DivX videos that were rented or
purchased with the DivX registration code of this
DVD player (see chapter ‘Adjust settings’ - [ General
Setup ] > [ DivX(R) VOD Code ] for details).
• If the subtitle does not appear correctly, change the
subtitle language (see chapter ‘Adjust settings’ [ Preferences ] > [ DivX Subtitle ] for details).
21
dvp3388_94_en.indd 21
2/19/2009 6:13:14 PM
Quick skip play
Play MP3/WMA music
1
MP3/WMA is a type of highly compressed
audio file (files with .mp3, .wma extensions).
During play, press
INFO until one of
the following options is selected.
Display
Action
[ Disc Go
To ]
Skip play to a specific time
within the disc.
[ Track Go
To ]
Skip play to a specific time
within a track
[ Select
Track ]
Skip play to a specific track
number.
2
Press the numeric buttons to change the
time/number where you want to skip to.
1
Insert a disc or USB that contains the MP3/
WMA music.
.
• For USB, press
A contents menu is displayed.
Play starts.
2
Select a track to play if play does not start
automatically.
• To select another track/folder, press
vV, then press OK.
3
To return to the main menu, press v until
the root menu is selected, then press OK.
Note
• For CDs recorded in multiple sessions, only the first
session is played.
• This DVD player does not support MP3PRO audio
format.
• If any special characters are present in the MP3
•
•
track name (ID3) or album name, it may not display
correctly on the screen because these characters are
not supported.
Some WMA is protected by Digital Rights
Management (DRM), it cannot be played on this
DVD player.
Folders/files exceed the supported limit of this DVD
player are not displayed or played.
Tip
• You can display the data disc contents without
folders, see chapter ‘Adjust settings’ - [ Preferences ]
> [ Mp3/Jpeg Nav ] for details.
22
dvp3388_94_en.indd 22
2/19/2009 6:13:14 PM
Play photo
Note
•
Play photos as slideshow
This DVD player can play JPEG photos (files
with .jpeg or .jpg extensions).
1
Insert a disc or USB that contains the JPEG
photos.
• For USB, press
.
For a Kodak disc, the slideshow begins
automatically.
For a JPEG disc, the photo menu is
displayed.
2
Select the folder/album you want to play.
• To preview the photos in the folder/
album, press
INFO.
• To go to previous or next screen
display, press í/ë.
•
•
content on the TV due to the large number of songs/
photos compiled onto one disc.
If the JPEG photo is not recorded with an ‘exif ’ type
file, the actual thumbnail picture is not be shown
on the display. It is replaced by a ‘blue mountain’
thumbnail picture.
This DVD player can only display digital camera
pictures according to the JPEG-EXIF format, typically
used by almost all digital cameras. It cannot display
Motion JPEG and pictures in formats other than
JPEG, or sound clips associated with pictures.
Folders/files exceed the supported limit of this DVD
player are not displayed or played.
Play
• You may require longer time to display the disc
Control photo play
1
2
Play photo slideshow.
Use the remote control to control the
photo.
Button
Action
b
Rotate the photo anticlockwise.
B
Rotate the photo clockwise.
v
Flip the photo vertically.
V
Flip the photo horizontally.
, ZOOM
Zoom in/ out.
• Play pause in zoom mode.
x
Stop disc play.
• To select a photo, press the navigation
buttons.
• To display the selected photo only,
press OK.
3
Press OK to start slideshow play.
• To return to the menu, press
BACK.
23
dvp3388_94_en.indd 23
2/19/2009 6:13:14 PM
Play musical slideshow
Play from USB device
Play MP3/WMA music files and JPEG photo
files simultaneously to create musical slideshow.
The MP3/WMA and JPEG files must be stored
on the same disc.
This DVD player plays/views MP3, WMA, DivX,
JPEG or WMV files that are stored on USB
device.
1
2
Play MP3/WMA music.
Navigate to the photo folder/album and
press OK to start slideshow play.
Slideshow begins and continues till the
end of the photo folder or album.
Audio continues to play till the end of
the disc.
• To return to the menu, press
3
4
To stop slideshow play, press x.
To stop music play, press x again.
BACK.
1
2
3
Connect a USB flash drive to the
(USB) jack on this DVD player.
Press
.
A contents menu is displayed.
Play starts.
Select a file to play if play does not start
automatically.
• For more information, see chapters
‘Play music, Play photo, Play video’ for
details.
4
To stop play, press x or remove the USB
device.
• To switch to the disc mode, press
or DISC MENU.
Tip
• If the device does not fi t into the USB jack, connect it
through a USB extension cable.
• Digital cameras that require additional programme
installation when connected to a PC are not
supported.
24
dvp3388_94_en.indd 24
2/19/2009 6:13:15 PM
6 Advanced
features
Note
• While you copy, never press any buttons.
• Copy-protected media cannot be copied.
You can transfer data files such as MP3, WMA
or JPEG from disc to the USB device.
1
2
3
4
5
Insert a disc contains the MP3/WMA/JPEG
files.
You can convert audio CDs into MP3 audio
files with this DVD player. The created MP3
audio files are saved in the USB device.
1
2
Press x to stop disc play.
Connect the USB flash drive to the
(USB) jack on this DVD player.
3
4
Select the file to copy, then press
SUBTITLE.
005/030
Select [ Yes ] in the menu and press OK.
Speed
Normal
Bitrate
128kbps
Track02
04:17
Yes
Track03
03:58
USB 1
Track04
04:51
Track05
03:53
Track06
04:09
Track07
04:38
Summary
Do you want
to copy this file
Press [OK] button
to change speed.
Start
Yes
TRACK
Track01
Device
Track 1
Track 4
During disc play, press AUDIO/CREATE
MP3.
CRT ID3
Previous
Track 3
Connect the USB flash drive to the
(USB) jack on this DVD player.
OPTIONS
\MP3
Track 2
Insert an audio CD.
Create MP3
Select [ Yes ] in the menu to start to copy,
then press OK.
00:00/00:00
Advanced features
Create MP3 files
Media copy
Exit
Select all
04:14
Deselect all
No
Track 5
Track 6
Track 7
5
Select the conversion options in the
[ OPTIONS ] panel and press OK.
Once complete, a new folder is created
automatically in the USB device to store
all the new data files.
6
To stop copy progress, press x, then
press OK.
25
dvp3388_94_en.indd 25
2/19/2009 6:13:15 PM
Option
Description
[ Speed ]
Select the write-to-file speed.
• If [ Normal ] speed is
selected, music play can be
heard while creating the
MP3 file.
[ Bitrate ]
Select the quality level.
Higher bitrate for better sound
quality and bigger file size.
• Default setting is [ 128
kbps ].
[ CRT ID3 ]
Copy track information into
the MP3 file.
• Default setting is [ Yes ].
[ Device ]
The created MP3 files can
only be saved in USB device.
6
7
Press B to access the [ TRACK ] panel.
Select the audio track, then press OK.
• To select another track, repeat step 7.
• To select all tracks, select [ Select all ]
in the menu and press OK.
• To deselect all tracks, select [ Deselect
all ] in the menu and press OK.
8
Select [ Start ] in the menu to start to
convert, then press OK.
Once complete, a new folder is created
automatically in the USB device to store
all the new MP3 files.
• To exit the menu, select [ Exit ] and
press OK.
Note
• While you convert, never press any buttons.
• DTS CDs and copy-protected CDs cannot be
converted.
• Write-protected or password-protected USB
devices cannot be used to store MP3 files.
26
dvp3388_94_en.indd 26
2/19/2009 6:13:15 PM
This section describes the various setting
options of this DVD player.
Symbol
Option
[ General Setup ]
4
Select a setting, then press OK.
• To return to the previous menu, press
b.
• To exit the menu, press SETUP.
Note
Adjust settings
7 Adjust settings
• See the explanations of the above options in the
following pages.
[ Audio Setup ]
[ Disc Lock ]
[ Video Setup ]
[ Preferences ]
Note
• If the setup option is grayed out, it means the setting
cannot be changed at the current state.
Set play restriction for a specific discs.
Before you start, place the disc in the disc
compartment (maximum 20 discs can be
locked).
• [ Lock ] – restrict access to the current
disc. The next time you want to play
this disc or unlock it, you need to enter
the password.
• [ Unlock ] – play all discs.
Tip
• You can set or change the password, go to
[ Preferences ] > [ Password ].
General setup
1
2
3
[ OSD Language ]
Press SETUP.
[ General Setup ] menu is displayed.
Press B.
Select an option, then press OK.
General Setup
Disc Lock
OSD Language
Sleep Timer
Auto Standby
DivX(R) VOD Code
Select the default on-screen menu
language.
[ Sleep Timer ]
Switch to standby automatically after the
preset time.
• [ Off ] – disable sleep mode.
• [ 15 Mins ], [ 30 Mins ], [ 45 Mins ],
[ 60 Mins ] – select the count down
time before the DVD player switches
to standby.
27
dvp3388_94_en.indd 27
2/19/2009 6:13:15 PM
[ Auto Standby ]
Turn off or on automatic standby switching
mode. It is an energy saving feature.
• [ On ] – switch to standby after 15
minutes of inactivity (for example, in
pause or stop mode).
• [ Off ] – disable auto standby mode.
[ DivX(R) VOD Code ]
Audio setup
1
2
3
Display the DivX® registration code.
Press SETUP.
[ General Setup ] menu is displayed.
Press V to select [ Audio Setup ], then
press B.
Select an option, then press OK.
Audio Setup
Tip
Analog Output
• Enter this DVD player’s DivX registration code when
Digital Audio
you rent or purchase video from www.divx.com/vod.
The DivX videos rented or purchased through the
DivX® VOD (Video On Demand) service can be
played only on the device to which it is registered.
HDMI Audio
Audio Sync
Volume
Sound Mode
Speaker Setup
CD Upsampling
4
Select a setting, then press OK.
• To return to the previous menu, press
b.
• To exit the menu, press SETUP.
Note
• See the explanations of the above options in the
following pages.
28
dvp3388_94_en.indd 28
2/19/2009 6:13:15 PM
Select the analog audio setting based on
the audio device that is connected through
the analog audio jack.
• [ Stereo ] – for stereo output.
• [ LT/RT ] – for surround sound output
through two speakers.
Note
• [ Digital Audio ] setting is only available if the
[ HDMI Audio ] is set to [ Off ].
• [ LPCM Output ] setting is only available if the
[ Digital Output ] is set to [ PCM only ].
• The higher the sampling rate, the better the sound
quality.
• [ Multi Channel ] – for multi channel
output.
[ HDMI Audio ]
[ Digital Audio ]
Select the audio output setting when you
connect this DVD player and the TV with
a HDMI cable.
Select the setting based on the digital
amplifier/receiver that is connected
through the digital jack.
• [ Digital Output ] – select the type of
digital output.
Option
Description
[ Off ]
Disable digital output.
[ All ]
The device supports
multi-channel audio
formats.
[ PCM Only ]
The device is not capable
of decoding multi-channel
audio. Audio is
downmixed to twochannel sound: see [
LPCM Output ] setting.
• [ LPCM Output ] – select the LPCM
(Linear Pulse Code Modulation) output
sampling rate.
Option
Description
[ 48kHz ]
For discs recorded at
sampling rate of 48 kHz.
[ 96kHz ]
For discs recorded at the
sampling rate of 96 kHz.
Adjust settings
[ Analog Output ]
• [ On ] – audio output through the TV.
• [ Off ] – disable audio output from the
TV.
[ Audio Sync ]
Set the default delay time for audio output
when you play a video disc.
1. Press OK.
2. Press b B to set the delay time.
3. Press OK to confirm and exit.
[ Volume ]
Set the default volume level when you play
a disc.
1. Press OK.
2. Press b B to set the volume.
3. Press OK to confirm and exit.
29
dvp3388_94_en.indd 29
2/19/2009 6:13:15 PM
[ Sound Mode ]
Select a preset sound effect to enhance
the audio output.
• [ 3D ] – select a virtual surround sound
effect that is produced from the left and
right audio channels.
• [ Movie Mode ] – select a sound effect
for movies.
• [ Music Mode ] – select a sound effect
for music.
[ Speaker Setup ]
When you connect a speaker system, you
can optimize surround output for the
connected speakers.
• [ Front Speaker ]
Option
Description
[ Large ]
Produce low frequency
signal below 120 Hz.
[ Small ]
Cannot produce low
frequency signal below
120 Hz.
• [ Center Speaker ] / [ Rear Speaker ]
Option
Description
[ Large ]
Produce low frequency
signal below 120 Hz.
[ Small ]
Cannot produce low
frequency signal below
120 Hz.
[ Off ]
No speaker is
connected.
• [ Subwoofer ]
Option
Description
[ On ]
A subwoofer is
connected.
[ Off ]
No subwoofer is
connected.
• [ Speakers Volume ] – Set the volume
level of each speaker to get the ideal
audio balance.
1. Press OK.
2. Select a speaker, then press b B to
adjust the volume.
3. Press OK to confirm and exit.
• [ Speakers Delay ] – Set the delay time
for the center, subwoofer and rear
speakers if they are placed closer to the
listening position, so that the sound
output from all speakers reach the
listening position at the same time.
1. Press OK.
2. Select a speaker, then press b B to
set the delay time.
3. Press OK to confirm and exit.
Note
• [ Speaker Setup ] setting is only available if you have
set the [ Analog Output ] setting to [ Multi Channel
].
[ CD Upsampling ]
For better sound quality in stereo mode,
convert the music CD to a higher sampling
rate.
• [ Off ] – turn off CD-upsampling.
• [ 88.2kHz ] – convert to twice the
original sampling rate.
• [ 176.4kHz ] – convert to four times
the original sampling rate.
[ Night Mode ]
You can play DVDs with Dolby Digital
mode at a low volume, without disturbing
others. High volume output is decreased
and low volume output is increased to an
audible level.
• [ On ] – turn on night mode.
• [ Off ] – enjoy surround sound with its
full dynamic range.
30
dvp3388_94_en.indd 30
2/19/2009 6:13:15 PM
1
2
3
Press SETUP.
[ General Setup ] menu is displayed.
Press V to select [ Video Setup ], then
press B.
Select an option, then press OK.
Video Setup
TV System
TV Display
Progressive
[ TV System ]
If the video does not appear correctly,
change the setting. By default, this setting
matches the most common setting for TVs
in your country.
• [ NTSC ] – for NTSC-system TV.
• [ Multi ] – for TV that is compatible
with both PAL and NTSC.
Adjust settings
Video setup
• [ PAL ] – for PAL-system TV.
[ TV Display ]
Select the screen format according to how
you want the picture to appear on the TV.
Picture Setting
HD JPEG
HDMI Setup
4
Select a setting, then press OK.
• To return to the previous menu, press
b.
• To exit the menu, press SETUP.
Note
• See the explanations of the above options in the
following pages.
4:3 Pan Scan (PS)
4:3 Letter Box (LB)
16:9 (Wide Screen)
• [ 4:3 Pan Scan ] – for standard TV, a
full-height screen display with the sides
trimmed.
• [ 4:3 Letter Box ] – for standard TV, a
‘wide-screen’ display with black bars on
the top and bottom.
• [ 16:9 ] – for wide-screen TV (frame
ratio 16:9).
[ Progressive ]
If a progressive scan TV is not connected
through HDMI cable, turn on progressive
scan mode.
• [ On ] – turn on progressive scan
mode.
• [ Off ] – disable progressive scan mode.
Tip
• There is more detailed description available. See
chapter ‘Get Started - Turn on Progressive Scan’ for
details.
31
dvp3388_94_en.indd 31
2/19/2009 6:13:15 PM
[ Picture Setting ]
Select a predefined set of picture color
settings or customize the personal setting.
• [ Standard ] – original color setting.
• [ Bright ] – vibrant color setting.
Note
• If the setting is not compatible with the TV, a blank
screen appears. Wait for 15 seconds for auto
recover or switch to its default mode as follows:
1) Press Z to open the disc compartment.
2) Press numeric button ‘1’.
• [ Soft ] – warm color setting.
• [ Personal ] – customize the color
setting. Set the level of brightness,
contrast, sharpness and color saturation,
then press OK.
• [ Wide Screen Format ] – define the
wide screen format for disc play.
Option
Description
[ Superwide ]
Center position of the
screen is stretched less
than the side. This
setting is only applicable
if the video resolution is
set to 720p or 1080i/p.
[ 4:3 Pillar
Box ]
No stretching of the
picture. Black bars are
displayed on both sides
of the screen. This
setting is only applicable
if the video resolution is
set to 720p or 1080i/p.
[ Off ]
Picture will be displayed
according to the format
of the disc.
[ HD JPEG ]
Enjoy untouched and uncompressed JPEG
pictures at it’s original resolution when you
connect this DVD video player and the TV
with a HDMI cable.
• [ On ] – display high definition picture.
• [ Off ] – display standard picture.
Note
• This DVD video player supports the resolution
display of 720p and above.
[ HDMI Setup ]
When you connect this DVD player and
the TV with a HDMI cable, select the best
HDMI setup that the TV can support.
• [ Resolution ] – select a video
resolution that is compatible with the
TV display capability.
Option
Description
[ Auto ]
It detect and select
the best supported
video resolution
automatically.
[ 480i ], [ 480p ],
[ 576i ], [ 576p ],
[ 720p ], [ 1080i ],
[ 1080p ]
Select a video
resolution that best
supported by the TV.
See the TVs manual
for details.
Note
• This setting is only available if you have set the [ TV
Display ] setting to [ 16:9 ].
32
dvp3388_94_en.indd 32
2/19/2009 6:13:15 PM
Option
Description
[ EasyLink ]
Turn off or turn on all
EasyLink features.
• To disable this feature,
select [ Off ].
[ One Touch
Play]
[ One Touch
Standby ]
Preferences
1
2
3
Note
• Philips does not guarantee 100% interoperability
Press V to select [ Preferences ] , then
press B.
Select an option, then press OK.
Preferences
When you press the
STANDBY button, it
turns on the TV and this
DVD player, then video
disc play starts (if a video
disc is found in the disc
compartment).
• To disable this feature,
select [ Off ].
When you press and
hold the STANDBY
button, all connected
HDMI CEC devices
switch to standby mode
simultaneously.
• To disable this feature,
select [ Off ].
Press SETUP.
[ General Setup ] menu is displayed.
Adjust settings
• [ EasyLink Setup ] – if this DVD player
is connected to HDMI CEC compliant
TV/devices, all connected devices can
respond to the following commands
simultaneously:
Audio
Subtitle
Disc Menu
Parental Control
PBC
Mp3/Jpeg Nav
Password
DivX Subtitle
4
Select a setting, then press OK.
• To return to the previous menu, press
b.
• To exit the menu, press SETUP.
Note
• Stop disc play before you can access to [ Preferences ].
• See the explanations of the above options in the
following pages.
with all HDMI CEC compliant devices.
• You must turn on the HDMI CEC operations on
the TV/devices before you can enjoy the EasyLink
controls. See the TVs/devices manual for details.
33
dvp3388_94_en.indd 33
2/19/2009 6:13:15 PM
[ Audio ]
[ PBC ]
Select the default audio language for
DVDs.
For VCDs/SVCDs recorded with PBC
(playback control), you can access the disc
content through an interactive menu.
[ Subtitle ]
• [ On ] – an index menu is displayed
when you load a disc for play.
Select the default subtitle language for
DVDs.
[ Disc Menu ]
Select the menu language for DVDs.
Note
• If the language you have set is not available on the
•
•
disc, the disc uses its own default language.
For some DVDs, the subtitle/audio language can only
change from the disc menu.
To select the languages that are not listed in the
menu, select [ Others ]. Then check the Language
Code list at the back of this user manual and enter
the respective language code.
[ Parental Control ]
Restrict access to DVDs that are unsuitable
for children. These types of DVDs must be
recorded with ratings.
1. Press OK.
2. Select a rating level, then press OK.
3. Press the numeric buttons to enter
the password.
• [ Off ] – skip the menu and start play
from the first track.
[ Mp3/Jpeg Nav ]
Select to display the folders or display all
the files.
• [ View Files ] – display all the files.
• [ View Folders ] – display the folders of
MP3/WMA files.
[ Password ]
Follow the instructions on the TV to set or
change the password for locked discs and
play restricted DVDs.
Preferences
Change password
Old Password
New Password
Confirm PWD
OK
Note
• Rated DVDs above the level you set in [ Parental
Control ] require a password to be played.
• The ratings are country-dependent. To allow all discs
to play, select ‘8’.
• Some DVDs have ratings printed on them but are
not recorded with ratings. This function has no
effect on such DVDs.
Tip
• You can set or change the password, go to
[ Preferences ] > [ Password ].
1. Press the numeric buttons to enter
‘136900’ or the last set password at [
Old Password ] field.
2. Enter the new password at [ New
Password ] field.
3. Enter the new password again at
[ Confirm PWD ] field.
4. Press OK to exit the menu.
Note
• If you forget the password, enter ‘136900’ before
you set a new password.
34
dvp3388_94_en.indd 34
2/19/2009 6:13:15 PM
[ DivX Subtitle ]
Select a character set that supports the
DivX subtitle.
Albanian, Danish, Dutch,
English, Finnish, French,
Gaelic, German, Italian,
Kurdish (Latin),
Norwegian, Portuguese,
Spanish, Swedish, Turkish
Adjust settings
[ Standard ]
Note
• Ensure that the subtitle file has the exact same file
name as the movie file. If for example the file name
of the movie is ‘Movie.avi’, then you will need to
name the text file ‘Movie.sub’ or ‘Movie.srt’.
[ Version Info ]
Display the software version of this DVD
player.
This information is required when you
want to find out if a newest software
version is available at the Philips website
that you may download and install on this
DVD player.
[ Default ]
Reset all the settings of this DVD player to
factory default, except for [ Disc Lock ],
[ Parental Control ] and [ Password ]
settings.
35
dvp3388_94_en.indd 35
2/19/2009 6:13:15 PM
8 Additional
information
Update software
4
5
Visit www.philips.com/support to check for
the latest software version, using the file
name for this DVD player.
Refer to the upgrade instructions for more
information.
Note
• Disconnect the power cord for a few seconds and
connect again to reboot the system.
To check for updates, compare the current
software version of this DVD player with the
latest software version (if available) at the
Philips website.
Caution
• Power supply must not be interrupted during
software upgrade.
1
Press SETUP.
Preferences
Disc Menu
Care
Caution
• Never use solvents such as benzene, thinner,
cleaners available commercially, or anti-static sprays
intended for discs.
Clean discs
Wipe the disc with a micro fibre cleaning cloth
from the center to the edge in a straight line
movement.
Parental Control
PBC
Mp3/Jpeg Nav
Password
DivX Subtitle
Version Info
Default
2
3
Select [ Preferences ] > [ Version Info ],
then press OK.
Write down the file name, then press
SETUP to exit the menu.
36
dvp3388_94_en.indd 36
2/19/2009 6:13:15 PM
Note
• Specification and design are subject to change
without notice.
Accessories supplied
• Quick Start Guide
• Remote control and batteries
• Audio/video cables
Playback media
• DVD-Video, Video CD/SVCD, Audio CD, CD-R/
CD-RW, DVD+R/+RW, DVD-R/-RW, DivX-CD,
Picture CD, MP3-CD, WMA-CD, WMV-CD, USB
flash drive
USB
• Compatibility: Hi-Speed USB (2.0)
• Class support: UMS (USB Mass Storage Class)
Audio performance
• DA converter: 24 bits, 192 kHz
• Frequency response:
• DVD: 4 Hz - 22 kHz (48 kHz);
4 Hz - 44 kHz (96 kHz)
• SVCD: 4 Hz - 20 kHz (44.1 kHz);
4 Hz - 22 kHz (48 kHz)
• CD/VCD: 4 Hz - 20 kHz (44.1 kHz)
• Signal-Noise (1 kHz): > 90 dB (A-weighted)
• Dynamic range (1 kHz): > 85 dB (A-weighted)
• Crosstalk (1 kHz): > 85 dB
• Distortion/noise (1 kHz): > 70 dB
• MPEG MP3: MPEG Audio L3
Specifi cation
9 Specification
Audio format
• Digital:
• MPEG/AC-3/PCM: Compressed digital (16, 20, 24
bits fs, 44.1, 48, 96 kHz)
• MP3 (ISO 9660): 96, 112, 128, 256 kbps &
variable bit rate fs, 32, 44.1, 48 kHz
• Analog sound stereo
• Dolby surround compatible downmix from Dolby
Digital multi-channel sound
Connections
TV standard
• Number of lines:
• 625 (PAL/50Hz); 525 (NTSC/60Hz)
• Playback: Multi-standard (PAL/NTSC)
Video performance
• Video DAC: 12 bits, 108 MHz
• Y Pb Pr: 0.7 Vpp ~ 75 ohm
• Video output: 1 Vpp ~ 75 ohm
Video format
• Digital compression:
• MPEG 2: DVD/SVCD
• MPEG 1: VCD/DivX
• Horizontal resolution:
• DVD: 720/1920 pixels (50 Hz); 720/1920 pixels
(60 Hz)
• VCD: 352 pixels (50 Hz); 352 pixels (60 Hz)
• Vertical resolution:
• DVD: 576/1080 lines (50 Hz); 480/1080 lines
(60 Hz)
• VCD: 288 lines (50 Hz); 240 lines (60 Hz)
•
•
•
•
Y Pb Pr output: Cinch 3x
Video output: Cinch (yellow)
Audio output (Front L+R): Cinch (white/red)
Digital output:
• 1 coaxial: IEC60958 for CDDA/LPCM;
IEC61937 for MPEG 1/2, Dolby Digital
• 1 optical
• HDMI output
• 5.1 channel analog output
• Audio Front L+R: Cinch (white/red)
• Audio Rear L+R: Cinch (white/red)
• Audio Center: Cinch (blue)
• Audio Subwoofer: Cinch (black)
37
dvp3388_94_en.indd 37
2/19/2009 6:13:15 PM
Main unit
• Dimensions (w x h x d): 360 x 37 x 209 (mm)
• Net Weight: approximately 1.3 kg
Power
• Power supply rating: 110 V - 240 V; 50/60 Hz
• Power consumption: < 12 W
• Power consumption in standby mode: < 0.3 W
Laser Specification
• Type: Semiconductor laser InGaAIP (DVD), AIGaAs
(CD)
• Wave length: 658 nm (DVD), 790 nm (CD)
• Output Power: 7.0 mW (DVD), 10.0 mW (VCD/CD)
• Beam divergence: 60 degrees
38
dvp3388_94_en.indd 38
2/19/2009 6:13:15 PM
Warning
• Risk of electric shock. Never remove the casing of
this unit.
To keep the warranty valid, never try to repair
the system yourself.
If you encounter problems when using this
DVD player, check the following points before
requesting service. If the problem remains
unsolved, register your product and get support
at www.philips.com/welcome.
If you contact philips, you will be asked for the
model and serial number of your DVD player.
The model number and serial number are on
the back or bottom of your DVD player. Write
the numbers here:
Model No. __________________________
Serial No. ___________________________
Main unit
The buttons on this DVD player do not work.
• Disconnect this DVD player from the
power outlet for a few minutes, then
connect again.
Picture
No picture.
• See TV manual for correct video input
channel selection. Change the TV channel
until you see the DVD screen.
• If this happens when you turn on the
progressive scan setting or change the TV
system setting, you have to switch to its
default mode:
1. Press Z to open the disc compartment.
2. Press the numeric button ‘1’ (for
progressive scan) or the numeric
button ‘3’ (for TV System).
No picture on HDMI connection.
• Check if the HDMI cable is faulty. Replace a
new HDMI cable.
• If this happens when you change the HDMI
video resolution, you have to switch to its
default mode:
1. Press Z to open the disc compartment
2. Press numeric button ‘1’.
Troubleshooting
10 Troubleshooting
Sound
No sound.
• Ensure that the audio cables are connected
and the connected device is turned on to
the correct input source.
No sound on HDMI connection.
• You may not hear any sound from the
HDMI output if the connected device is
non-HDCP compliant or only DVIcompatible.
• Ensure that the [ HDMI Audio ] setting is
turned on.
No sound during DivX movies play.
• The audio codec may not be supported by
this DVD player.
39
dvp3388_94_en.indd 39
2/19/2009 6:13:15 PM
Play
DivX video files cannot be played.
• Ensure that the DivX video file is complete.
• Ensure that the file name extension is
correct.
The aspect ratio of the screen is not aligned
with the TV display setting.
• The aspect ratio is fixed on the DVD.
DivX subtitle are not displayed correctly.
• Ensure that the subtitle file name is the
same as the movie file name.
• Select the correct character set.
1. Press SETUP.
2. Select [ Preferences ] > [ DivX
Subtitle ] in the menu.
3. Select the character set that supports
the subtitle.
The contents of the USB flash drive cannot be
read.
• The USB flash drive format is not
compatible with this DVD player.
• Drive is formatted with different file system
which is not supported by this DVD player
(e.g. NTFS).
40
dvp3388_94_en.indd 40
2/19/2009 6:13:15 PM
A
Aspect ratio
Aspect ratio refers to the length to height ratio
of TV screens. The ratio of a standard TV is 4:3,
while the ratio of a high-definition or wide TV is
16:9. The letter box allows you to enjoy a
picture with a wider perspective on a standard
4:3 screen.
D
DivX®
The DivX code is a patent-pending, MPEG-4
based video compression technology,
developed by DivX Networks, Inc., that can
shrink digital video to sizes small enough to be
transported over the internet, while maintaining
high visual quality.
H
HDMI
High-Definition Multimedia Interface (HDMI) is
a high-speed digital interface that can transmit
uncompressed high definition video and digital
multichannel audio. It delivers high quality
picture and sound quality, completely free from
noise. HDMI is fully backward-compatible with
DVI.
As required by the HDMI standard, connecting
to HDMI or DVI products without HDCP
(High-bandwidth Digital Content Protection)
will result in no Video or Audio output.
J
JPEG
A very common digital still picture format. A
still-picture data compression system proposed
by the Joint Photographic Expert Group, which
features small decrease in image quality in spite
of its high compression ratio. Files are
recognised by their file extension ‘JPG or JPEG’.
Glossary
12 Glossary
M
MP3
A file format with a sound data compression
system. ‘MP3’ is the abbreviation of Motion
Picture Experts Group 1 (or MPEG-1) Audio
Layer3. By using the MP3 format, one CD-R or
CD-RW can contain about 10 times more data
than a regular CD. Files are recognized by their
file extension ‘.MP3’.
O
One-touch play
When you connect the DVD player to devices
that support one-touch play, you can control
the DVD player and the devices with one
remote control. For example, when you press
Play on the DVD remote control, the TV
automatically switches to the correct channel to
show the DVD content.
One-touch standby
When you connect the DVD player to devices
that support standby, you can use DVD player
remote control to put the DVD player and all
connected HDMI devices in standby mode. You
can perform one-touch standby using the
remote control from any of the connected
HDMI devices.
41
dvp3388_94_en.indd 41
2/19/2009 6:13:15 PM
P
PBC
Playback Control. A system of navigating a
Video CD/Super VCD through on-screen
menus recorded onto the disc. You can enjoy
interactive play and searching.
Progressive Scan
The progressive scan displays twice the number
of frames per second than ordinary TV system.
It offers higher picture resolution and quality.
W
WMA
Windows Media™ Audio. Refers to an audio
compression technology developed by
Microsoft Corporation. WMA data can be
encoded by using Windows Media Player
version 9 or Windows Media Player for
Windows XP. Files are recognized by their file
extension ‘WMA’.
WMV
A video file or stream in Windows Media
format. It is a compression format of motion
picture based on MPEG-4 developed by
Microsoft.
42
dvp3388_94_en.indd 42
2/19/2009 6:13:15 PM
Language Code
Abkhazian
6566
Afar
6565
Afrikaans
6570
Amharic
6577
Arabic
6582
Armenian
7289
Assamese
6583
Avestan
6569
Aymara
6589
Azerhaijani
6590
Bahasa Melayu
7783
Bashkir
6665
Belarusian
6669
Bengali
6678
Bihari
6672
Bislama
6673
Bokmål, Norwegian
7866
Bosanski
6683
Brezhoneg
6682
Bulgarian
6671
Burmese
7789
Castellano, Español
6983
Catalán
6765
Chamorro
6772
Chechen
6769
Chewa; Chichewa; Nyanja 7889
9072
中文
Chuang; Zhuang
9065
Church Slavic; Slavonic 6785
Chuvash
6786
Corsican
6779
Česky
6783
Dansk
6865
Deutsch
6869
Dzongkha
6890
English
6978
Esperanto
6979
Estonian
6984
Euskara
6985
6976
Faroese
7079
Français
7082
Frysk
7089
Fijian
7074
Gaelic; Scottish Gaelic 7168
Gallegan
7176
Georgian
7565
Gikuyu; Kikuyu
7573
Guarani
7178
Gujarati
7185
Hausa
7265
Herero
7290
Hindi
7273
Hiri Motu
7279
Hrwatski
6779
Ido
7379
Interlingua (International)7365
Interlingue
7365
Inuktitut
7385
Inupiaq
Irish
Íslenska
Italiano
Ivrit
Japanese
Javanese
Kalaallisut
Kannada
Kashmiri
Kazakh
Kernewek
Khmer
Kinyarwanda
Kirghiz
Komi
Korean
Kuanyama; Kwanyama
Kurdish
Lao
Latina
Latvian
Letzeburgesch;
Limburgan; Limburger
Lingala
Lithuanian
Luxembourgish;
Macedonian
Malagasy
Magyar
Malayalam
Maltese
Manx
Maori
Marathi
Marshallese
Moldavian
Mongolian
Nauru
Navaho; Navajo
Ndebele, North
Ndebele, South
Ndonga
Nederlands
Nepali
Norsk
Northern Sami
North Ndebele
Norwegian Nynorsk;
Occitan; Provencal
Old Bulgarian; Old Slavonic
Oriya
Oromo
Ossetian; Ossetic
Pali
Panjabi
Persian
Polski
Português
7375
7165
7383
7384
7269
7465
7486
7576
7578
7583
7575
7587
7577
8287
7589
7586
7579
7574
7585
7679
7665
7686
7666
7673
7678
7684
7666
7775
7771
7285
7776
7784
7186
7773
7782
7772
7779
7778
7865
7886
7868
7882
7871
7876
7869
7879
8369
7868
7878
7967
6785
7982
7977
7983
8073
8065
7065
8076
8084
Pushto
Russian
Quechua
Raeto-Romance
Romanian
Rundi
Samoan
Sango
Sanskrit
Sardinian
Serbian
Shona
Shqip
Sindhi
Sinhalese
Slovensky
Slovenian
Somali
Sotho; Southern
South Ndebele
Sundanese
Suomi
Swahili
Swati
Svenska
Tagalog
Tahitian
Tajik
Tamil
Tatar
Telugu
Thai
Tibetan
Tigrinya
Tonga (Tonga Islands)
Tsonga
Tswana
Türkçe
Turkmen
Twi
Uighur
Ukrainian
Urdu
Uzbek
Vietnamese
Volapuk
Walloon
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
8083
8285
8185
8277
8279
8278
8377
8371
8365
8367
8382
8378
8381
8368
8373
8373
8376
8379
8384
7882
8385
7073
8387
8383
8386
8476
8489
8471
8465
8484
8469
8472
6679
8473
8479
8483
8478
8482
8475
8487
8571
8575
8582
8590
8673
8679
8765
6789
8779
8872
8973
8979
9085
43
dvp3388_94_en.indd 43
2/19/2009 6:13:15 PM
Electronics
Visit us on web at www.philips.com/support or
Call us on Tel. No.: 1860-180-1111 (BSNL / MTNL)*
011-6600-1111 (GSM / WLL)*
* “standard call rates apply”
44
dvp3388_94_en.indd 44
2/19/2009 6:13:15 PM
45
dvp3388_94_en.indd 45
2/19/2009 6:13:15 PM
46
dvp3388_94_en.indd 46
2/19/2009 6:13:15 PM
47
dvp3388_94_en.indd 47
2/19/2009 6:13:15 PM
© 2009 Koninklijke Philips Electronics N.V.
All right reserved
sgptt_0908/94
dvp3388_94_en.indd 48
2/19/2009 6:13:15 PM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement