Philips Spotify multiroom adapter SW100M/10 User manual

Philips Spotify multiroom adapter SW100M/10 User manual
Always there to help you
Register your product and get support at
www.philips.com/support
Question?
Contact
Philips
User manual
SW100M
Contents
1Important2
Safety2
Notice2
2 Your audio adapter4
Introduction4
What's in the box
4
What else you need
4
8 Product information20
Specifications
20
9Troubleshooting21
10 Appendix: Understand meanings
of LED colors22
3 Overview of the main unit5
4Prepare6
Download SpeakerSet Multiroom
Manager to your iOS or Android device 6
Connect to your audio system
6
Connect power and switch on
7
5 Connect SW100M to your home
Wi-Fi network8
Option 1: Set up through an iOS device 9
Option 2: Set up through an Android
device10
Option 3: Set up wireless connection
to a WPS router directly
11
Option 4: Set up through a PC/Mac
(advanced)12
Rename speakers
12
6Play13
Enjoy Spotify music services through
SW100M13
Stream music to multiple speakers/
audio adapters at the same time
14
7 Other features18
Restore factory settings
Update software
18
19
EN
1
1Important
Safety
•
Only use attachments/accessories specified
by the manufacturer.
•
Use only power supplies listed in the user
manual.
•
The product shall not be exposed to
dripping or splashing.
•
Do not place any sources of danger on the
product (e.g. liquid filled objects, lighted
candles).
•
Where the mains plug or an appliance
coupler is used as the disconnect device,
the disconnect device shall remain readily
operable. Warning
•• Never remove the casing of this apparatus.
•• Never lubricate any part of this apparatus.
•• Never place this apparatus on other electrical
the essential requirements and other
relevant provisions of Directive 1999/5/
EC. You can find the Declaration of
Conformity on www.philips.com/support.
Any changes or modifications made to this
device that are not expressly approved by
WOOX Innovations may void the user’s
authority to operate the equipment.
Philips and the Philips’ Shield Emblem are
registered trademarks of Koninklijke Philips N.V.
and are used by WOOX Innovations Limited
under license from Koninklijke Philips N.V.
Specifications are subject to change without
notice. WOOX reserves the right to change
products at any time without being obliged
to adjust earlier supplies accordingly.
Disposal of your old product
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
equipment.
•• Keep this apparatus away from direct sunlight, naked
flames or heat.
•• Ensure that you always have easy access to the power
cord, plug or adaptor to disconnect this apparatus from
the power.
Risk of overheating! Never install this
apparatus in a confined space. Always
leave a space of at least four inches around
this apparatus for ventilation. Ensure
curtains or other objects never cover
the ventilation slots on this apparatus.
Notice
Hereby, WOOX Innovations declares
that this product is in compliance with
2
EN
This symbol on a product means that the
product is covered by European Directive
2012/19/EU. Inform yourself about the local
separate collection system for electrical and
electronic products. Follow local rules and
never dispose of the product with normal
household waste. Correct disposal of old
products helps prevent negative consequences
for the environment and human health. Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy
to separate into three materials: cardboard
(box), polystyrene foam (buffer) and
polyethylene (bags, protective foam sheet.)
Your system consists of materials which
can be recycled and reused if disassembled
by a specialized company. Please observe
the local regulations regarding the
disposal of packaging materials, exhausted
batteries and old equipment. Trademark notice
iPad, iPhone, iPod, iPod classic, iPod nano
and iPod touch are trademarks of Apple Inc.,
registered in the U.S. and other countries.
Lightning is a trademark of Apple Inc.
Android is a trademark of Google Inc. Use of
this trademark is subject to Google permissions. Class II equipment symbol:
CLASS II apparatus with double insulation,
and no protective earth provided. Note
•• The type plate is located on the bottom of the
apparatus.
EN
3
2 Your audio
adapter
What else you need
To stream Spotify music wirelessly to the
audio adapter through Wi-Fi, you need:
• a certified Wi-Fi router
Congratulations on your purchase, and
welcome to Philips! To fully benefit from
the support that Philips offers, register your
product at www.philips.com/welcome.
If you contact Philips, you will be asked
for the model and serial number of
this apparatus. The model number and
serial number are on the bottom of the
apparatus. Write the numbers here:
Model No. __________________________
Serial No. ___________________________
Introduction
After connection of this audio adapter
to your audio system, you can:
• stream Spotify music wirelessly via
Spotify Connect with your iOS or
Android device as remote control
• listen to Spotify music everywhere
at your home through group
play (multiple Spotify Multiroom
speakers required)
What's in the box
Check and identify the contents
of your package:
• Audio adapter
• 1 x AC power adapter
• Printed materials
4
EN
• an iOS or Android device, such
as an iPod touch/iPhone/iPad or
an Android phone or tablet
• the SpeakerSet and Spotify
(with a premium account) apps
available on Apple App Store
(for iOS devices) or Google Play
Store (for Android devices)
Your audio adapter should be connected
to the same local network as your iOS or
Android device through the Wi-Fi router.
3 Overview of the
main unit
a b c
g OPTICAL OUT
• Connect the audio adapter to your
audio system through an optical cable
(not supplied).
h COAX OUT
• Connect the audio adapter to your
audio system through a coaxial cable
(not supplied).
i AUX OUT
d
• Connect the audio adapter to your
audio system through RCA audio
cables (red/white; not supplied).
j DC IN
• Connect the power adapter.
j
a
i h gf e
/
• Skip to the previous/next song.
b
• Start or pause music play.
c -/+
• Adjust volume.
d System status indicator
• Show the current status of the audio
adapter.
e WPS button/indicator
• Enter WPS Setup mode for connection
of the audio adapter to a Wi-Fi
network.
• Show the Wi-Fi setup
status in WPS mode.
f SETUP button/indicator
• Enter App-Assisted Wi-Fi Setup mode
for connection of the audio adapter to
a Wi-Fi network.
• Show the Wi-Fi setup status.
EN
5
4Prepare
2
On the initial setup page, tap Setup a new
speaker.
Always follow the instructions in sequence.
Download SpeakerSet
Multiroom Manager to your
iOS or Android device
1
(For iPod touch/iPhone/iPad users) Install
SpeakerSet from Apple App Store, and
then run the app.
Connect to your audio
system
To enjoy music, first connect the
audio adapter to your audio system
in one of the following ways:
(For users of Android smartphones or
tablets) Install SpeakerSet from Google
Play Store and then run the app.
Option 1: Connect through AUX
OUT
L
R
L
6
EN
R
Option 2: Connect through
COAXIAL OUT
Connect power and switch
on
Caution
•• Risk of product damage! Make sure that the power
supply voltage matches the voltage printed on the
bottom of the audio adapter.
•• Risk of electric shock! When you unplug the AC
adapter, always pull the plug from the socket. Never
pull the cord.
•• Before you connect the AC adapter, make sure that you
have completed all the other connections.
•
Note
•• Make sure that no cable is plugged in the AUX OUT
sockets.
As instructed on the app screen, connect
the AC power adapter to
• the DC IN socket on the back of the
audio adapter.
• the wall power socket.
»» The audio adapter switches on
automatically.
Option 3: Connect through OPTICAL
OUT
»» The system status indicator on the
front panel blinks amber during bootup.
»» If a Wi-Fi connection has been set
up for the audio adapter, the system
status indicator turns solid green after
successful connection.
OPTICAL OUT
Note
•• Make sure that no cable is plugged in the AUX OUT
sockets.
Tip
•• The audio adapter enters standby mode automatically
after 15 minutes of inactivity.
EN
7
5Connect
SW100M to
your home WiFi network
To connect the audio adapter to your existing
home Wi-Fi network, you need to apply your
home Wi-Fi settings to the audio adapter
in one of the following ways (depending on
the type of your smart device and whether
your Wi-Fi router is WPS enabled):
Devices
required
for speaker
setup
iOS device
+ Wi-Fi
router
Android
device
+ Wi-Fi
router
WPS Wi-Fi
router
PC/Mac
with Wi-Fi
enabled
+ Wi-Fi
router
8
EN
Setup method
Choose option 1 (see
'Option 1: Set up through
an iOS device' on page 8).
Choose option 2 (see
'Option 2: Set up through an
Android device' on page 9).
Choose option 3 (see
'Option 3: Set up wireless
connection to a WPS router
directly' on page 10).
Choose option 4 (see 'Option
4: Set up through a PC/Mac
(advanced)' on page 11).
Before connection of the audio adapter to
your home Wi-Fi network, make sure that:
ayour Wi-Fi router is powered
on and working properly.
bthe audio adapter has been powered
on and booted up successfully.
c(for option 1, 2 and 4 only) you
have jotted down the password
of your home Wi-Fi router.
* If your Wi-Fi password contains
such special characters as #/:/;/', you
need to change your password.
Once connected successfully, the audio
adapter will remember your home WiFi settings. Whenever the audio adapter
is powered on, it is connected to your
home Wi-Fi network automatically.
Option 1: Set up through an
iOS device
1
Before setup, make sure that your iOS
device is connected to your home Wi-Fi
network.
2
As instructed on the app, press and hold
SETUP on the back of the audio adapter
for more than 3 seconds.
»» Both the system status indicator on
the front panel and the Wi-Fi status
indicator on the SETUP button turns
solid amber.
3
Tap Next on the above app screen, and
then read how to proceed with network
setup.
4
Select Wireless (Wi-Fi) under HOW DO
YOU WANT TO CONNECT?.
5
As instructed, exit the app, and then select
:) Philips Setup from the list of available
Wi-Fi networks.
6
After automatic detection of the audio
adapter successfully, open the SpeakerSet
app again.
7
Select the name of your home Wi-Fi
network under Select a network to use
speaker.
8
Enter the password of your home Wi-Fi
network, and then tap Done to finish
setup.
9
Wait until successful connection of
the audio adapter to your home Wi-Fi
network.
»» The Wi-Fi status indicator on the
SETUP button turns off.
»» The system status indicator on the
front panel turns solid green.
EN
9
Option 2: Set up through an
Android device
1
2
10
Before setup, make sure that your Android
device is connected to your home Wi-Fi
network.
As instructed on the app, press and hold
SETUP on the back of the audio adapter
for more than 3 seconds.
»» Both the system status indicator on
the front panel and the Wi-Fi status
indicator on the SETUP button turns
solid amber.
EN
3
Tap Next on the above app screen, and
then read how to proceed with network
setup.
4
Select Wireless (Wi-Fi) under HOW DO
YOU WANT TO CONNECT?.
5
Select the name of your home Wi-Fi
network under Select a network to use
speaker.
6
Enter the password of your home Wi-Fi
network, and then tap Done to finish
setup.
7
Wait until successful connection of
the audio adapter to your home Wi-Fi
network.
»» The Wi-Fi status indicator on the
SETUP button turns off.
»» The system status indicator on the
front panel turns solid green.
Option 3: Set up wireless
connection to a WPS router
directly
1
2
Press the WPS button on your home
Wi-Fi router.
WPS
As instructed on the app, press and hold
WPS on the back of the audio adapter for
more than 3 seconds.
»» The Wi-Fi status indicator on the WPS
button blinks green.
3
Wait until successful connection of the
speaker to your home Wi-Fi network.
»» The Wi-Fi status indicator on the WPS
button turns off.
»» The system status indicator on the
front panel turns solid green.
Tip
•• Only WPA and WPA2 are supported. If the wireless
security is WEP or no security is applied, the WPS
method does not work.
•• For some Wi-Fi routers, you may need to hold the
WPS button for Wi-Fi connection or enable the WPS
PBC function from the router configuration pages. See
the user manuals of the specific routers for details.
WPS
EN
11
Option 4: Set up through a
PC/Mac (advanced)
1
2
Go to your Wi-Fi enabled PC/Mac.
3
Select :) Philips Setup from the list of
available Wi-Fi networks on your PC/Mac.
4
After successful connection, open a web
browser on your PC/Mac.
5
Enter http://philips.speakers or 172.24.0.1
at the address bar and click the Enter key.
6
Make changes on the setup page and
confirm your settings.
»» The Wi-Fi status indicator on the
SETUP button turns off.
»» The system status indicator on the
front panel turns solid green.
12
Press and hold SETUP on the back of the
audio adapter for more than 3 seconds.
»» Both the system status indicator on
the front panel and the Wi-Fi status
indicator on the SETUP button turns
solid amber.
EN
Rename speakers
1
After successful Wi-Fi setup, go to the
home page and tap the speaker icon on
the app screen.
2
Tap
3
Rename the speaker as you like.
4
Tap Done to confirm.
beside the speaker name.
6Play
3
Tap the Connect icon
screen.
4
Select the audio adapter for music
streaming.
on the play
Enjoy Spotify music services
through SW100M
Note
•• With Spotify, you can enjoy unlimited music on your
new device. Thanks to the Spotify Connect feature, you
can play and control all this music wirelessly. Choose
music on your mobile or tablet, and hear it on your
brand new device.
•• Make sure that the audio adapter is connected to your
home Wi-Fi network with Internet connection available.
1
Switch to the Spotify app from SpeakerSet
or open the Spotify app directly.
2
Log in to your Spotify premium account.
Username
Password
Philips SW100M xxxxxx
5
Stream music from the Spotify app to the
audio adapter.
»» You can enjoy music through your
audio system connected to the audio
adapter.
EN
13
During play, you can:
• press
on the audio adapter to
pause/resume music play.
• press / on the audio adapter
to skip to the previous/next song.
Group and ungroup speakers/audio
adapters
1
Connect multiple Spotify Multiroom
Speakers/audio adapters to your home
Wi-Fi network (see 'Connect SW100M to
your home Wi-Fi network' on page 8).
2
Run SpeakerSet on your iOS/Android
smartphone or tablet.
3
On the home page, tap beside a
speaker/audio adapter to act as the master
speaker of a group.
• press +/- on the audio adapter
to adjust volume level.
Tip
•• See the SpeakerSet app screen for more advanced
settings.
•• You can take your iOS or Android device away from
the network, or even switch it off. In this case, Spotify
music will continue to play on your audio adapter.
Stream music to multiple
speakers/audio adapters at
the same time
You can add multiple Spotify Multiroom
Speakers/audio adapters connected to the
same Wi-Fi network into a group. Then,
you can stream music from Spotify on your
iOS or Android device in the same Wi-Fi
network to all speakers/audio adapters in
the group at the same time. In this way, you
can enjoy music everywhere at your home.
14
EN
4
Tick circles beside the speakers/audio
adapters to add them into the group.
5
Tap beside the group name to enter the
edit page.
6
Edit the group name as you like on the edit
page.
7
Tap the check mark at the top right on the
above app screen, and then wait for more
than 10 seconds until the grouping finishes.
To ungroup speakers:
1
2
Tap
beside the master speaker.
Untick the box beside the speaker/audio
adapter to be removed from the group.
EN
15
Enjoy music streamed to the group
speakers/audio adapters
1
On the home page, tap the icon of the
master speaker on the SpeakerSet app
screen.
2
Tap Go Spotify app to play music to
switch to the Spotify app.
3
4
Log in to your Spotify premium account.
5
Select and play your favorite music from
the Spotify app.
»» You can enjoy music streamed to all
speakers/audio adapters in the same
group at the same time.
16
EN
Tap the Connect icon
master speaker.
to select the
To adjust volume of all speakers/audio
adapters in a group at the same time:
1
Open the SpeakerSet app, then tap
on the main page to enter the volume
adjustment page.
2
Move the group volume slider to adjust
volume of all speakers/audio adapters in
the group at the same time.
To adjust volume of an individual
speaker/audio adapter:
•
Press +/- on the top panel of the speaker/
audio adapter.
•
Open the SpeakerSet app, then move the
slider beside the speaker/audio adapter on
the above volume adjustment page directly.
To play/pause music play:
•
on the top panel of any speaker/
Press
audio adapter in the group or use controls
on the Spotify app screen directly.
Tip
•• On the volume adjustment page of the SpeakerSet app,
you can also tap beside a speaker/audio adapter to
mute/unmute its volume output.
•• More music controls and sound settings are available
on the SpeakerSet app screen, such as bass/treble
adjustment.
Adjust audio delay
2
Tap Audio sync to enter the audio
synchronization page.
3
Adjust the audio delay time until the sound
output is synchronized.
During group play, if the audio output from
your audio system connected to the audio
adapter is not synchronized with that from
the other speakers in the group, you can
adjust the delay time for the audio adapter
to synchronize with the other speakers.
1
Open the SpeakerSet app, then tap the
image of the audio adapter on the main
page to see the available options.
EN
17
7 Other features
5
Tap Factory reset to enter the factory
reset page.
6
Tap Yes to reset your audio adapter.
Restore factory settings
In some cases, you may need to reset the
audio adapter, for example, when you need
to reset the Wi-Fi settings or log out from
the current Spotify premium account.
1
Make sure that the audio adapter is
powered on and connected to the same
Wi-Fi network as your smartphone or
tablet.
2
Make sure that your home Wi-Fi network
is connected to the Internet.
3
Run SpeakerSet on your iOS or Android
smartphone or tablet.
4
Tap the image of the audio adapter to see
the available options.
If the above operation fails, you can reset
the audio adapter in the following way:
1
2
Unplug the power cable.
Hold both the + and keys on the top
panel and then plug in the power cable
again.
Tip
•• The audio adapter reboots after factory reset.
•• Your Spotify account will be logged out after factory
reset.
•• If the reset audio adapter is running in a group, it will be
ungrouped. When the master speaker is reset, one of
the other speakers in the group will serve as the master
speaker instead.
18
EN
Update software
5
Tap Software update to enter the software
update page.
6
Tap Check online to see whether any new
version of software is available.
7
If a new version is available, tap Update to
start software update.
»» The system status indicator on the
front panel blinks amber and red
alternately during this process.
8
Wait until the software update process
finishes, then tap OK to reboot the audio
adapter.
To improve product performance,
Philips may offer you new software for
you to update your audio adapter.
Warning
•• Always connect your audio adapter to AC power for
firmware upgrade. Never power off your audio adapter
nor close the app during firmware upgrade.
1
Make sure that audio adapter is powered
on and connected to the same Wi-Fi
network as your smartphone or tablet.
2
Make sure that your home Wi-Fi network
is connected to the Internet.
3
Run SpeakerSet on your iOS or Android
smartphone or tablet.
4
Tap the image of the audio adapter to see
the available options.
Tip
•• Depending on the network connection, it may take 10
minutes to finish update.
EN
19
8Product
information
•• Product information is subject to change without prior
notice.
Specifications
Audio output
Output Voltage
Signal to Noise Ratio
Total Harmonic Distortion
1000 mV RMS
> 62 dBA
< 2%
Wireless
Frequency
range
WPS
PBC (one
button
push)
20
EN
AC power
PHILIPS
SWITCHING
POWER SUPPLY
Note
Wireless
standard
Wireless
security
General information
802.11b/g/n
WEP, 10 or 26 hex digit keys
WPA (TKIP) or WPA2 (TKIP /
AES) with 8 - 40 ASCII printable
characters passphrase
2412 - 2462 MHz (CH1CH11) (for /37, /55)
2412 - 2472 MHz (CH1-CH13)
(for /12, /10, /05, /79, /98)
Yes
Operation Power
Consumption
Power Consumption
in Network Standby
Dimensions
Model:
S018KM0500200;
input: 100 - 240
V~, 50/60 Hz 500
mA; output: 5.0
V 2000 mA
< 10 W
< 2W
- Main Unit (L x W x H)
Weight
179 x 105 x 66 mm
- Main Unit
0.4 kg
9Troubleshooting
Warning
•• Never remove the casing of this apparatus.
To keep the warranty valid, never try
to repair the system yourself.
If you encounter problems when using this
apparatus, check the following points before
requesting service. If the problem remains
unsolved, go to the Philips web site (www.
philips.com/welcome). When you contact Philips,
ensure that the apparatus is nearby and the
model number and serial number are available.
No power
••
••
••
Make sure that the AC power plug of the
audio adapter is connected properly.
Make sure that there is power at the AC
outlet.
Check whether the audio adapter is in
standby mode (see 'Connect power and
switch on' on page 7). No sound
••
••
••
••
••
Check whether the audio adapter is
correctly connected to your audio system.
Check whether your audio system is
powered on.
Check whether the audio adapter is muted
or the streamed music is still buffering. The
system status indicator blinks green when
the audio adapter is muted or during music
buffering. If the audio adapter is muted,
adjust volume on the SpeakerSet app or
on the audio adapter directly.
Check the Wi-Fi network connection.
Set up the network again if needed (see
'Connect SW100M to your home Wi-Fi
network' on page 8).
If there is no sound from a speaker in a
group, check whether the speaker is out of
range. You can check whether the wireless
connection of the speaker is poor on the
app screen directly. No response from the speaker
•• Restart the audio adapter, and then
set up the Wi-Fi network for the audio
adapter again (see 'Connect SW100M to
your home Wi-Fi network' on page 8).
•• Disconnect and reconnect the AC power
plug to switch on the speaker again.
•• If there is no sound from a speaker in a
group, check whether the speaker is out of
range. You can check whether the wireless
connection of the speaker is poor on the
app screen directly. How can I reconfigure the Wi-Fi settings?
•• Reset the speaker (see 'Restore
factory settings' on page 18), and
then configure the Wi-Fi settings again
(see 'Connect SW100M to your
home Wi-Fi network' on page 8). Occasional breaking of music streaming
Do one or all of the following:
••
••
••
••
••
••
Move SW100M closer to your Wi-Fi router.
Remove any obstacles between SW100M
and your Wi-Fi router.
Avoid using Wi-Fi channel which is
overlapped by the nearby Wi-Fi network.
Check if your network speed is fast enough
(in cases where multiple devices share the
same router, the wireless performance may
be affected). Turn off the other devices
connected to your home router.
Enable the Quality of Service (QoS)
option (if available on the Wi-Fi router).
Turn off other Wi-Fi routers. No response from the audio adapter
•• Restart the audio adapter, and then
set up the Wi-Fi network for the audio
adapter again (see 'Connect SW100M to
your home Wi-Fi network' on page 8).
•• Disconnect and reconnect the AC power
plug to switch on the audio adapter again.
•• If there is no sound from a speaker in a
group, check whether the speaker is out of
range. You can check whether the wireless
connection of the speaker is poor on the
app screen directly.
EN
21
10Appendix:
Understand
meanings of
LED colors
1 solid green
1
1 blinking green
quickly
1 blinking green
slowly
1
1
a
1
1 dimmed by 50%
in solid green
1
1 solid red
1 blinking red
1
c
1
b
1
a System status indicator
(on the front panel)
1
b SETUP indicator (on the back panel)
c WPS indicator (on the back panel)
LED
colors
1
1 and 2 indicators
in solid amber
2
1 blinking amber
quickly, and 3
blinking green
1
1
22
LED behavior
No light
1 blinking amber
slowly
1 blinking amber
quickly
1
1
2
EN
Status of
the audio
adapter
Power off
Booting up
Connecting
to a
network
In appassisted Wi-Fi
setup mode
In WPS
mode
1 solid red, and
2 solid amber
1 blinking red
and amber
1 blinking red,
amber and green
alternately
Network
connection
successful
During audio
buffering
Muted or
playback
paused
In standby
mode with
network
connection
In standby
mode
without
network
connection
Network
connection
failed
During
factory reset
During
firmware
upgrade
Firmware
upgrade
failed
Open Source Declaration for Philips
SW700M/SW750M/SW100M
ALAC
FLAC
Iperf
jQuery
JSBN 1.2
Jungo USB DFU Driver
Marvell WPS2 Client
mDNSResponder
OpenSSL
RSA MD5
zlib
getopt
Mongoose
Tremor
ALAC
http://alac.macosforge.org/
The Apple Lossless Audio Codec sources are available under the Apache license. Details can be
found here http://www.apache.org/licenses/LICENSE-2.0.
FLAC
https://xiph.org/flac/license.html
The FLAC and Ogg FLAC formats themselves, and their specifications, are fully open to the
public to be used for any purpose (the FLAC project reserves the right to set the FLAC
specification and certify compliance). They are free for commercial or noncommercial use. That
means that commercial developers may independently write FLAC or Ogg FLAC software which
is compatible with the specifications for no charge and without restrictions of any kind. There
are no licensing fees or royalties of any kind for use of the formats or their specifications, or for
distributing, selling, or streaming media in the FLAC or Ogg FLAC formats.
The FLAC project also makes available software that implements the formats, which is
distributed according to Open Source licenses as follows:
The reference implementation libraries are licensed under the New BSD License. In simple
terms, these libraries may be used by any application, Open or proprietary, linked or
incorporated in whole, so long as acknowledgement is made to Xiph.org Foundation when
using the source code in whole or in derived works. The Xiph License is free enough that the
libraries have been used in commercial products to implement FLAC, including in the firmware
of hardware devices where other Open Source licenses can be problematic. In the source code
these libraries are called libFLAC and libFLAC++.
The rest of the software that the FLAC project provides is licensed under the GNU General
Public License (GPL). This software includes various utilities for converting files to and from
FLAC format, plugins for audio players, et cetera. In general, the GPL allows redistribution as
long as derived works are also made available in source code form according to compatible
terms.
Neither the FLAC nor Ogg FLAC formats nor any of the implemented encoding/decoding
methods are covered by any known patent.
FLAC is one of a family of codecs of the Xiph.org Foundation, all created according to the same
free ideals. For some other codecs' descriptions of the Xiph License see
the Speex and Vorbis license pages.
Iperf
http://pirlwww.lpl.arizona.edu/resources/guide/software/iperf/
Copyright 1999,2000,2001,2002,2003
The Board of Trustees of the University of Illinois
All rights reserved
Permission is hereby granted, free of charge, to any person obtaining a copy of this software
(Iperf) and associated documentation files (the "Software"), to deal in the Software without
restriction, including without limitation the rights to use, copy, modify, merge, publish,
distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the
Software is furnished to do so, subject to the following conditions:
Redistributions of source code must retain the above copyright notice, this list of
conditions and the following disclaimers.
Redistributions in binary form must reproduce the above copyright notice, this list of
conditions and the following disclaimers in the documentation and/or other materials
provided with the distribution.
Neither the names of the University of Illinois, NCSA, nor the names of its contributors
may be used to endorse or promote products derived from this Software without
specific prior written permission.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE CONTIBUTORS OR
COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN
AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION
WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
See UI License for complete details.
jQuery
http://jquery.org
jQuery projects are released under the terms of the MIT license.
The MIT License is simple and easy to understand and it places almost no restrictions on what
you can do with a jQuery project.
You are free to use any jQuery project in any other project (even commercial projects) as long
as the copyright header is left intact.
JSBN
jsbn is released under a BSD license. See LICENSE for details.
Licensing
--------This software is covered under the following copyright:
/*
* Copyright (c) 2003-2005 Tom Wu
* All Rights Reserved.
*
* Permission is hereby granted, free of charge, to any person obtaining
* a copy of this software and associated documentation files (the
* "Software"), to deal in the Software without restriction, including
* without limitation the rights to use, copy, modify, merge, publish,
* distribute, sublicense, and/or sell copies of the Software, and to
* permit persons to whom the Software is furnished to do so, subject to
* the following conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
* EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
* WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
*
* IN NO EVENT SHALL TOM WU BE LIABLE FOR ANY SPECIAL, INCIDENTAL,
* INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND, OR ANY DAMAGES WHATSOEVER
* RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER OR NOT ADVISED OF
* THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF LIABILITY, ARISING OUT
* OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
*
* In addition, the following condition applies:
*
* All redistributions must retain an intact copy of this copyright notice
* and disclaimer.
*/
Address all questions regarding this license to:
Tom Wu
[email protected]
Jungo USB DFU Driver
http://www.jungo.com/st/products/drivercore-advanced-usb-drivers/
BSD license
Marvell WPS2 client
http://www.marvell.com/
BSD license
mDNSResponder
http://www.opensource.apple.com/source/mDNSResponder/mDNSResponder-320.10.80/
The majority of the source code in the mDNSResponder project is licensed
under the terms of the Apache License, Version 2.0, available from:
<http://www.apache.org/licenses/LICENSE-2.0>
To accommodate license compatibility with the widest possible range
of client code licenses, the shared library code, which is linked
at runtime into the same address space as the client using it, is
licensed under the terms of the "Three-Clause BSD License".
The Linux Name Service Switch code, contributed by National ICT
Australia Ltd (NICTA) is licensed under the terms of the NICTA Public
Software Licence (which is substantially similar to the "Three-Clause
BSD License", with some additional language pertaining to Australian law).
OpenSSL
http://www.openssl.org
OpenSSL is based on the SSLeay library developed by Eric Young and Tim Hudson. The OpenSSL
toolkit is licensed under an Apache-style licence which basically means that you are free to get
and use it for commercial and non-commercial purposes.
RSA MD5
/* MD5C.C - RSA Data Security, Inc., MD5 message-digest algorithm
*
* Copyright (C) 1991-2, RSA Data Security, Inc. Created 1991. All
* rights reserved.
*
* License to copy and use this software is granted provided that it
* is identified as the "RSA Data Security, Inc. MD5 Message-Digest
* Algorithm" in all material mentioning or referencing this software
* or this function.
*
* License is also granted to make and use derivative works provided
* that such works are identified as "derived from the RSA Data
* Security, Inc. MD5 Message-Digest Algorithm" in all material
* mentioning or referencing the derived work.
*
* RSA Data Security, Inc. makes no representations concerning either
* the merchantability of this software or the suitability of this
* software for any particular purpose. It is provided "as is"
* without express or implied warranty of any kind.
*
* These notices must be retained in any copies of any part of this
* documentation and/or software.
Zlib
http://www.zlib.net/
/* zlib.h -- interface of the 'zlib' general purpose compression library
version 1.2.8, April 28th, 2013
Copyright (C) 1995-2013 Jean-loup Gailly and Mark Adler
This software is provided 'as-is', without any express or implied
warranty. In no event will the authors be held liable for any damages
arising from the use of this software.
Permission is granted to anyone to use this software for any purpose,
including commercial applications, and to alter it and redistribute it
freely, subject to the following restrictions:
1. The origin of this software must not be misrepresented; you must not
claim that you wrote the original software. If you use this software
in a product, an acknowledgment in the product documentation would be
appreciated but is not required.
2. Altered source versions must be plainly marked as such, and must not be
misrepresented as being the original software.
3. This notice may not be removed or altered from any source distribution.
Jean-loup Gailly
[email protected]
Mark Adler
[email protected]
*/
getopt
http://cvsweb.netbsd.org/bsdweb.cgi/src/lib/libc/stdlib/
BSD license
Mongoose
https://github.com/cesanta/mongoose/
Mongoose is released under commercial and GNU GPL v.2 open source licenses. The GPLv2
open source License does not generally permit incorporating this software into non-open
source programs. For those customers who do not wish to comply with the GPLv2 open source
license requirements,Cesanta Software offers a full, royalty-free commercial license and
professional support without any of the GPL restrictions.
Tremor
http://wiki.xiph.org/index.php/Tremor
BSD license
2015 © WOOX Innovations Limited.
All rights reserved.
Philips and the Philips’ Shield Emblem are registered
trademarks of Koninklijke Philips N.V. and are used
by WOOX Innovations Limited under license from
Koninklijke Philips N.V.
SW100M_UM_10_V2.0
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement