Philips | DVDR3360H/75 | Philips Hard disk/DVD recorder DVDR3360H/75 User manual

Philips Hard disk/DVD recorder DVDR3360H/75 User manual
User Manual
LASER
Type
Semiconductor laser
InGaAlP (DVD)
AIGaAs (CD)
Wave length
658 nm (DVD)
790 nm (CD)
Output Power 30 mW(DVD±RW write)
1.0 mW (DVD read)
1.0 mW (CD read)
Beam divergence 84 degrees (DVD)
61 degrees (CD)
‘CONSUMERS SHOULD NOTE THAT NOT ALL HIGH
DEFINITION TELEVISION SETS ARE FULLY
COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE
ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN
CASE OF 525 OR 625 PROGRESSIVE SCAN PICTURE
PROBLEMS, IT IS RECOMMENDED THAT THE USER
SWITCH THE CONNECTION TO THE ‘STANDARD
DEFINITION’ OUTPUT. IF THERE ARE QUESTIONS
REGARDING OUR TV SET COMPATIBILITY WITH THIS
MODEL 525p AND 625p DVD PLAYER, PLEASE
CONTACT OUR CUSTOMER SERVICE CENTER.’
For Customer Use:
Read carefully the information located at
the bottom or rear of your HDD/ DVD
Recorder and enter below the Serial No.
Retain this information for future reference.
Model No. DVDR 3360H / DVDR 3370H
Serial No. _______________
2
CAUTION
Use of controls or adjustments or
performance of procedures other than
herein may result in hazardous radiation
exposure or other unsafe operation.
This product incorporates copyright protection
technology that is protected by US patents. Use of
this copyright protection technology must be
authorized by Macrovision, and is intended for
home and other limited viewing uses only unless
otherwise authorized by Macrovision. Reverse
engineering or disassembly is prohibited.
U.S. Patent Number 4,631,603; 4,819,098;
4,907,093; 5,315,448; and 6,516,132
Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D symbol
are trademarks of Dolby Laboratories.
G-CODE ® is a registered trademark of Gemstar
Development Corporation. The G-CODE ® system is
manufactured under licence from Gemstar
Development Corporation.
DivX®, DivX Certified, and associated logos are
trademarks of DivX, Inc and are used under license.
3
Table of Contents
English
General
Special Features ................................................................................................................ 6
Frequently Asked Questions........................................................................................... 7
Care and Safety Information .......................................................................................... 8
Setup precautions.................................................................................................................................................8
Cleaning discs ........................................................................................................................................................8
HDD (Hard Disk Drive) handling care ..........................................................................................................8
General Information ........................................................................................................ 9
Introduction ...........................................................................................................................................................9
Accessories supplied ...........................................................................................................................................9
Region codes..........................................................................................................................................................9
Copyright notice ...................................................................................................................................................9
Product Overview
Remote Control ............................................................................................................. 10
Inserting Batteries..............................................................................................................................................12
Main Unit ......................................................................................................................... 13
Connections
Step 1: Basic Recorder Connections ............................................................................ 14
Connecting the antenna cables ......................................................................................................................14
Connecting the video cable .............................................................................................................................15
Connecting the audio cables ...........................................................................................................................16
Step 2: Optional Connections....................................................................................... 17
Connecting to a Cable Box or Satellite Receiver .....................................................................................17
Connecting to a VCR or other similar device............................................................................................18
Connecting to a VCR and Cable Box/Satellite Receiver.........................................................................19
Connecting a camcorder to the front jacks............................................................................................... 20
Step 3: Installation and Setup ....................................................................................... 21
Finding the viewing channel .............................................................................................................................21
Setting your TV channel programs................................................................................................................21
GENERAL settings .................................................................................................................................... 22
Setting the language ...........................................................................................................................................24
Setting the time & date .....................................................................................................................................24
LANGUAGE settings ................................................................................................................................ 25
DATE/ TIME settings................................................................................................................................. 25
Watch TV
Control TV programs .................................................................................................... 26
Switching on to TV program .......................................................................................................................... 26
Pause live TV function...................................................................................................................................... 26
Instant Replay function .................................................................................................................................... 26
Recording
Before Recording ............................................................................................................ 27
About temporary HDD storage (Time Shift Buffer) .................................................................................27
Accessing the HDD (Hard Disk Storage) Setup Menu ......................................................................... 28
HDD settings ...............................................................................................................................................29
Default Recording settings ............................................................................................................................ 30
GENERAL settings .....................................................................................................................................31
4
Record on Hard Disk ...................................................................................................... 32
Recording TV programs ...................................................................................................................................32
Recording from a DV camcorder ...................................................................................................................32
Recording from an external device (Camcorder/VCR/ DVD player) .................................................33
Record on DVD Recordable Disc.................................................................................. 35
Copying from HDD to a recordable DVD ................................................................................................. 35
Discs for recording ........................................................................................................................................... 35
Recording from various sources ................................................................................................................... 36
Timer Recording ............................................................................................................. 38
About timer recording ..................................................................................................................................... 38
Timer recording (G- CODE ® System) ............................................................................................................. 38
Timer recording (manually) ............................................................................................................................ 40
Changing/ Deleting a timer recording ..........................................................................................................41
Playback
Playback from Hard Disk ............................................................................................... 42
Playback your HDD recordings..................................................................................................................... 42
Playback from Disc ......................................................................................................... 43
Playable discs ...................................................................................................................................................... 43
Inserting a disc ................................................................................................................................................... 43
Starting disc playback ....................................................................................................................................... 44
Additional Playback Features ....................................................................................... 47
Changing to another title/chapter/track .....................................................................................................47
Pausing playback and step play ......................................................................................................................47
Searching forward/backward ..........................................................................................................................47
Zooming in ...........................................................................................................................................................47
Using m(INFO) options ................................................................................................................................ 48
Edit Recordings
Edit Recordings - HDD ................................................................................................... 51
About HDD title edit menu ............................................................................................................................51
Accessing the HDD title edit menu ..............................................................................................................51
Edit Recordings - Recordable DVD .............................................................................. 54
About disc edit menu ....................................................................................................................................... 54
Accessing disc editing menu ........................................................................................................................... 54
Playing your recordings (DVD±R) on other DVD players .................................................................... 56
About DVD title editing ...................................................................................................................................57
Accessing DVD title edit menu ......................................................................................................................57
About video editing ...........................................................................................................................................59
Accessing video editing menu .........................................................................................................................59
Other Information
Setup Menu Options....................................................................................................... 62
Accessing the Setup Menu ...............................................................................................................................62
VIDEO settings ........................................................................................................................................... 63
PREFERENCES settings............................................................................................................................ 64
AUDIO settings .......................................................................................................................................... 65
Firmware Upgrade ......................................................................................................... 66
Installing the latest firmware.......................................................................................................................... 66
Troubleshooting .............................................................................................................. 67
Specifications .................................................................................................................. 70
Glossary ........................................................................................................................... 71
Display panel symbols/ messages ................................................................................. 72
TV System Guide ............................................................................................................ 74
5
English
Table of Contents
Special Features
English
‘Time Shift Buffer’
As soon as you turn on this recorder, the
program shown on the TV will be stored into
the ‘Time Shift Buffer’. It acts as a
temporary HDD storage of your recordings.
The contents will automatically be deleted
after 3 hours, when you turn off this recorder
or when you switch it to standby mode. To
store the contents on the hard disk, you have
to mark the segment in the ‘Time Shift Buffer’
for recording to prevent them from being
deleted.
‘Instant Replay’
You can repeat a scene of a live TV program
by pressingÑ button on the remote control,
as often as you like.
To return to the live TV program, press and
holdÉ.
‘Pause Live TV’
A live TV program is now under your control.
You can pause the program by pressing
PAUSEÅ button. Resume playback at the
scene it was interrupted by pressing the
PLAYÉbutton.
To return to the live TV program, press and
holdÉ.
‘Direct Recording to DVD’
This feature enables you to record content
directly on to a recordable DVD disc.
Press the DVD REC button on the remote
control to activate direct recording to the
recordable DVD disc.
6
This is a simple programming system for
recorders. To use it, enter the programming
number associated with your television
program.You can find this number in your
favourite listings magazine.
i.Link is also known as ‘FireWire’ and
‘IEEE1394’. This connection is used for the
transfer of high bandwidth digital signals as
used by digital video (DV) camcorders. It
carries all audio and video signals via a single
cable.
What kind of disc should I use for
recording?
You can only record on both DVD±R and
DVD±RW discs. DVD±R/±RW is the most
compatible recordable DVD format on the
market today. They are fully compatible to
most of the existing DVD-Video players and
DVD-ROM drives in computers.
What are Titles and Chapters?
A DVD disc contains Titles and Chapters,
which are similar to the Titles and Chapters of
a book. A Title is often a complete movie and
is broken down into Chapters, or individual
scenes from the movies.
Title
Chapter
What is the capacity of a
DVD recordable disc?
4.7GB, or equivalent to 6 CDs. You can store
only one hour of recordings on a single disc at
the highest quality (DVD standard) and about
6 hours recordings at the lowest quality
(VHS standard.)
The mode of record quality indicates the
number of hours that will fit on a single disc.
What is the difference between
DVD±R and DVD±RW?
Title
Chapter Chapter Chapter Chapter
chapter markers
A program is recorded as a single title, it may
consist of one chapter or a few chapters
within a title, depending on the recording
settings.
DVD±Rs are “recordable” discs and
DVD±RWs are “rewritable” discs. With a
DVD±R disc, you can record multiple sessions
on the same disc, but when the disc is full, you
cannot record any more content on the disc.
The DVD±RW disc allows you to record over
the same disc repeatedly.
How do I set up Titles and Chapters?
The recorder will automatically create a new
Title each time you start a new recording.
– For DVD recordings, you can add chapters
manually.
– For HDD recordings, you can preset
chapters to be automatically inserted at
5-minutes intervals.
What is DV?
What does “finalizing” a disc do?
Using DV, also known as i.LINK, you can
connect a DV-equipped camcorder to this
recorder using a single DV cable for input and
output of audio, video, data and control signals.
– This recorder is only compatible with
DV-format (DVC-SD) camcorders. Digital
satellite tuners and Digital VHS video
recorders are not compatible.
– You cannot connect more than one DV
camcorder at any one time to this recorder.
– You cannot control this recorder from
external equipment connected via the
DV IN jack.
Can I copy a VHS tape or DVD
from an external player?
Yes, but only if the VHS tape or DVD is not
copy-protected.
Finalizing a disc locks the disc so it can no
longer be recorded, only required for
DVD±Rs. It will then be compatible with
virtually any DVD player. To close a disc
without finalizing it, simply stop recording and
eject the disc. You will still be able to record
on the disc if there is capacity for more
recordings.
How good is the quality of the
recording?
There are six modes of record quality levels
to choose from, ranging from “HQ” (1 hour
recording at high quality) to “SLP” (6 hours
recording at VHS quality) on a recordable
DVD. Choose the quality level that best suits
your purpose and the length of material.
Record Quality
HQ High Quality
SP Standard Play
SP+ Standard Play Plus
LP Long Play
EP Extended Play
SLP Super Long Play
Hours of Recording that can be stored
DVDR3360H
160GB HDD
34
68
85
102
136
204
DVDR3370H
250GB HDD
53
106
132
159
212.5
318
DVD±R/
DVD±RW
1
2
2.5
3
4
6
Values are estimates only. Parts of the HDD storage capacity will be reserved for
the operations of this recorder and time shifting.
7
English
Frequently Asked Questions
Care and Safety Information
English
CAUTION!
High voltage! Do not open the
device. You run the risk of getting
an electric shock.
The machine does not contain any
user-serviceable parts. Please leave
all maintenance work to qualified
personnel.
Setup precautions
Finding a suitable location
– Place the set on a flat, hard and stable
surface. Do not place the set on a carpet.
– Do not position the set on top of
other equipment that might heat it up
(e.g., receiver or amplifier.)
– Do not put anything under the set
(e.g., CDs, magazines.)
– Install this unit near the AC outlet and
where the AC power plug can be reached
easily.
Space for ventilation
– Place the apparatus in a location with
adequate ventilation to prevent internal
heat build up. Allow at least 10 cm (4”)
clearance from the rear and the top of
the set and 5 cm (2”) from the left and
right to prevent overheating.
Avoid high temperatures, moisture,
water and dust
– Apparatus must not be exposed to
dripping or splashing.
– Do not place any sources of danger
on the apparatus (e.g., liquid filled
objects, lighted candles.)
Cleaning discs
Some problems occur because the disc
inside the recorder is dirty (frozen picture,
sound disruptions, picture distortions.) To
avoid these problems, discs should be
cleaned on a regular basis.
To clean a disc, use a micro fibre cleaning
cloth and wipe the disc from the center
to the edge in a straight line.
CAUTION!
Do not use solvents such as benzene,
thinner, commercially available cleaners,
or anti-static sprays intended for discs.
HDD (Hard Disk Drive)
handling care
The HDD is a fragile piece of device that
is easily prone to damage due to its long
recording capacity and high speed
operation.
– Do not move the unit while it is turned
on.
– Do not remove the AC power plug
from the power outlet during operation.
– Do not use the unit in excessively hot
or humid places. It may cause
condensation to form inside the unit.
If the HDD fails, playback and recording
will not be possible. In this case, it will be
necessary to replace the HDD unit.
WARNING!
The HDD is not a device for storing
recorded content permanently. We
recommend that you copy the important
video content to a recordable DVD as
backup.
8
Introduction
Accessories supplied
This recorder has a built-in hard disk
drive (HDD). You can record up to
204 ~ 318 hours of video in SLP (Super
Long Play) record quality mode.
–
–
–
–
Model
Internal hard
disk drive
English
General Information
Remote control and batteries
Audio/video (AV) cables
RF coaxial cable
Quick Start Guide
Maximum
recording hours
DVDR3360H
160 GB
204
DVDR3370H
250 GB
318
Note: These values are estimates only. Parts of the HDD
storage capacity will be reserved for the operations of this
recorder and time-shifting.
This recorder allows you to enjoy the
flexibility to keep recordings in the HDD
or copy to a recordable DVD for future
playback.
Furthermore, you can take advantage of
features like ‘Instant Replay’, or ‘Pause
Live TV’; see the section “Control TV
programmes”.
Before you can start using this recorder,
you must complete the basic connections
and set-up in three easy steps.
Region codes
DVD films are usually not released at the
same time in all regions of the world,
thus all DVD players are keyed to a
specific region code.
The regional code is shown on the back
panel of this device. If the DVD is
marked with a different region code, it
cannot be played back on this device.
Region
Asia Pacific,
Taiwan, Korea
DVD that can
be played
ALL
3
ALL
4
Step 1: Basic recorder connections
Step 2: Optional connections for
other devices
Australia,
New Zealand,
Latam
Step 3: Basic installation and set-up
Please take time to read this user manual
before using your recorder. It contains
important information and notes
regarding operations of the recorder.
Helpful Hints:
– If you have any questions or if problems
occur during operation, see the chapter
‘Troubleshooting’.
– If you need further assistance, please call
the customer support service for your
country. The corresponding telephone
numbers and e-mail addresses are given in
the guarantee booklet.
– Refer to the type plate on the rear or
bottom of the product for identification and
supply ratings.
Copyright notice
The making of unauthorized copies of
copy-protected material, including
computer programs, files, broadcasts and
sound recordings, may be an infringement
of copyrights and constitute a criminal
offence. This equipment should not be
used for such purposes.
9
Remote Control
English
d
–
a
–
Cursor buttons for moving to the left/ right or
making a forward/reverse search.
In time shift mode, use
button to jump
forward 30 seconds and
button to jump
backward by 10 seconds.
: Cursor buttons for moving up/down.
e m (INFO)
–
b
c
d
–
Displays the Time Shift video bar. It shows the
timing of the TV programs stored in the
temporary HDD storage.
Displays the on-screen help text.
f PLAYÉ
–
–
Plays a disc.
Plays a recording.
g REC
e
f
g
h
i
j
k
l
m
n
–
Starts recording the current TV channel or the
current video input source.
h .>
–
Skips to previous or next Chapter/Track.
i RETURN
–
Returns to the previous menu of a video CD
(VCD) or some DVDs.
j SHUFFLE
–
–
–
Switches to random playback of an audio CD,
Video CD (VCD), picture CD or DVD disc.
In HDD title menu, select to sort the titles.
In tuner mode, selects between dual language
broadcasts.
k REPEAT
–
–
Select to repeat title playback in HDD mode.
Select to repeat playback of title, chapter,
track or disc in DVD mode.
a STANDBY-ON 2
l SOURCE
–
–
Turns on the recorder or switch to standby
mode.
b CH + / –
While in tuner mode, selects the next/
previous TV channel.
c OK
–
–
10
Stores/confirms an entry.
Confirms a selection.
In tuner or DVD REC mode, selects the
recorder’s video input source from the TV
channel or external sources.
( EXT1, CAM1, CAM2.)
m DVD REC
–
Activates the ‘direct recording to DVD’ mode.
n TUNER
–
Switches to the recorder’s tuner mode
(TV channel.)
Remote Control (continued)
–
–
English
o Numeric keypad
Selects a chapter/track number to play.
Selects the recorder’s preset TV tuner
channel.
p TV VOL +/ –
–
Adjust the volume of the TV set (Philips TV
only.)
q SETUP
–
o
Enters/exits the system setup menu.
r STOP
–
–
Stops playback/recording.
Hold down the button to open and close the
disc tray.
p
s PAUSEÅ
–
–
Pauses the playback.
Pauses ‘Live TV’ viewing.
t ZOOM
–
Enlarges a picture on the TV screen.
u T/C
–
Displays title/chapter information.
v SELECT
–
–
Selects a track/chapter/file in the program
menu.
In HDD title menu, marks titles for copying to
a DVD recordable disc.
w TIMER
–
Enters/exits the timer recording menu.
q
r
s
t
u
v
w
x
y
z
x HDD
–
Enters the HDD content menu.
y DVD
–
Switches to disc mode or displays the disc
content menu.
z DV
–
Switches to ‘camera mode’ for camcorder
connected to DV IN jack. Recording can be
made directly onto the HDD/DVD.
11
Remote Control (continued)
English
Inserting Batteries
Using the remote control to
operate the system
3
1
2
A Open the battery compartment.
B Insert two batteries type R06 or AA,
following the indications (+-) inside
the compartment.
C Close the cover.
CAUTION!
– Remove batteries if they are
exhausted or if the remote control
will not be used for a long time.
– Do not mix batteries (old and new
or carbon and alkaline, etc.).
– Batteries contain chemical
substances and should be
disposed of properly.
12
A Aim the remote control directly at the
remote sensor (iR) on the front panel.
B Select the source you want to control by
pressing the TUNER, HDD or DVD
button on the remote control.
C Select the desired function (for example
., >.)
English
Main Unit
a STANDBY-ON 2
– Turns on the recorder or switch to
standby mode.
b Disc tray
c OPEN/CLOSE ç
– Opens/closes the disc tray.
d Display panel
– Show information about the current
status of the recorder.
e IR
– Point the remote control towards this
sensor
f HDD Active indicator
– Blue ring lights up while temporary
recording to the time shift buffer is in
progress.
g
– Starts recording the current TV channel
or the current video input source.
– Red ring lights up while recording to the
HDD or DVD recordable disc is in
progress.
É
– Starts playback of the selected title/track.
./>
– Skips to the previous or next chapter/
track, or hold down the button to make
a reverse/forward search.
– Stops playback/recording.
Jacks behind the flap
Flip down the door as indicated by the
OPENÉlabel at the right hand corner.
h S-VIDEO
– S-video input for SVHS/Hi8 camcorders
or SVHS/Hi8 video recorders.
In tuner mode, press SOURCE on the
remote control repeatedly to select
‘CAM2’ when using this input source.
i VIDEO
– Video input for camcorders or video
recorders.
In tuner mode, press SOURCE on the
remote control repeatedly to select
‘CAM1’ when using this input source.
j L/R AUDIO
– Audio input for camcorder or the audio/
video device which is connected to the
S-VIDEO or VIDEO jack.
k DV IN
– Input for digital camcorders or other
suitable devices using this connector.
Press DV on the remote control when
using this input source.
13
Step 1: Basic Recorder Connections
English
CABLE
ANTENNA
SATELLITE
A
~
ANTENNA
MAINS
VIDEO
(CVBS)
VIDEO
(CVBS)
Y
S-VIDEO
(Y/C)
L
AUDIO
TV
R
EXT1
PB
L
AUDIO
PR
R
COAXIAL
AUDIO
OUT 2
OUT 1
DIGITAL AUDIO OUT
B
TV
AU D IO
O U T
S-V ID E O
IN
V ID E O IN
Connecting the antenna
cables
These connections enable you to watch
and record TV programs using this
recorder. If the antenna signal is
connected via a VCR, Cable Box or
Satellite Receiver, ensure that these
devices are turned on in order to watch
or record the cable programs.
If you want to connect to a VCR
and/or Cable Box/Satellite Receiver,
see page 17~18 for the complete
connection to your TV.
A Connect the existing Antenna/Cable TV
signal (or from the Cable Box/Satellite
Receiver {RF OUT or TO TV}) to the
ANTENNA
jack on the recorder.
B Use the supplied RF coaxial cable to
jack on the recorder
connect the TV
to the antenna input jack on your TV
(VHF/UHF RF IN.)
Helpful Hint:
– Depending on how you have currently
connected your TV channel (directly from an
off-air antenna or Cable box or VCR), you
will have to disconnect some of the cables
before you make the above connection.
TIPS: Before making or changing any connections, make sure that all the devices are disconnected
from the power outlet.
14
ANTENNA
VIDEO
(CVBS)
VIDEO
(CVBS)
English
Step 1: Basic Recorder Connections (continued)
Y
S-VIDEO
(Y/C)
L
AUDIO
TV
PB
L
AUDIO
R
PR
R
COAXIAL
AUDIO
EXT1
OUT 2
OR
OUT 1
DIGITAL AUDIO OUT
OR
Option 3
Option 1
Option 2
TV
AU D IO
O U T
S-V ID E O
IN
V ID E O IN
Connecting the video cable
This connection enables you to view the
disc playback from the recorder.
You only need to choose one of the
options below to make your video
connection.
Option 1: Using Video (CVBS) jack
Use the supplied audio/video cable
(yellow plug) to connect the VIDEO
(CVBS)-OUT2 jack on the recorder to
the video input jack (or labeled as A/V In,
Video In or Composite) on the TV.
Option 2: Using S-Video jack
Use an S-video cable (not supplied) to
connect the S-VIDEO (Y/C) - OUT2
jack on the recorder to the S-Video input
jack (or labeled as Y/C or S-VHS) on the
TV.
Option 3 : Using Component Video
jack
A Use the component video cable (red/
blue/green - not supplied) to connect the
Y PB PR -OUT1 jacks on the recorder
to the corresponding component video
input jacks (or labeled as Y Pb/Cb Pr/Cr
or YUV) on the TV.
B If your TV accepts Progressive Scan
signal, see page 63 for detailed
Progressive Scan set up.
IMPORTANT!
The progressive scan video quality is
only available through a Y PB PR
connection and a progressive TV is
required. It is strongly advised to
complete the recorder installation
first, before enabling the progressive
scan feature.
TIPS: Before making or changing any connections, make sure that all the devices are disconnected
from the power outlet.
15
Step 1: Basic Recorder Connections (continued)
English
ANTENNA
VIDEO
(CVBS)
VIDEO
(CVBS)
Y
S-VIDEO
(Y/C)
L
AUDIO
TV
R
EXT1
PB
L
AUDIO
PR
R
COAXIAL
AUDIO
OUT 2
DIGITAL AUDIO OUT
OUT 1
Option 2
OR
Option 1
DIGITAL IN
TV
AU D IO
O U T
S-V ID E O
IN
V ID E O IN
AV amplifier/
receiver
This connection enables you to listen to
the sound.
Option 2: Using a Coaxial cable
You can connect the recorder to an AV
amplifier/receiver in order to enjoy
multichannel surround sound.
Option 1: Using an Audio cable
You can connect the recorder to a two
channel stereo system or receiver in
order to enjoy the stereo sound system.
Use a coaxial cable (not supplied) to
connect the COAXIAL jack to the
digital input on the AV amplifier/receiver
with a digital multichannel sound
decoder.
Connecting the audio cables
Use the supplied audio cable (red/white
ends) to connect the AUDIO L/R
OUT1 or -OUT2 jacks to these devices
with the same input jacks.
Before you start operating, set the audio
settings accordingly (see page 65.)
If the AUDIO settings do not match your
amplifier’s capabilities, the amplifier may
produce a strong, distorted sound or no
sound at all.
Helpful Hint:
– Do not connect your TV’s audio output
jacks to the AUDIO L/R (IN-EXT) jacks on
this recorder, this may cause unwanted
noise.
TIPS: Before making or changing any connections, make sure that all the devices are disconnected
from the power outlet.
16
English
Step 2: Optional Connections
CABLE
A
IN
RF
VIDEO
Back of a Cable
Box or Satellite
Receiver (Example
only)
OUT
R
AUDIO
L
S-VIDEO
SATELLITE
D
ANTENNA
B
~
ANTENNA
MAINS
VIDEO
(CVBS)
VIDEO
(CVBS)
E
Y
S-VIDEO
(Y/C)
L
AUDIO
TV
R
EXT1
PB
L
AUDIO
PR
R
COAXIAL
AUDIO
OUT 2
OUT 1
DIGITAL AUDIO OUT
C
TV
AU D IO
O U T
S-V ID E O
IN
V ID E O IN
Connecting to a Cable Box or
Satellite Receiver
Option 1
If your Cable Box/Satellite Receiver
has only an antenna output jack
(RF OUT or TO TV),
refer to “Connecting the antenna cables”
on page 14 for the complete connection
to your TV.
Option 2
If your Cable Box/Satellite Receiver
has video/audio output jacks,
A Keep the existing antenna connection
from the Cable Box/Satellite Receiver to
your TV.
B Use the supplied RF coaxial cable to
jack on the
connect the ANTENNA
recorder to the RF OUT jack on the
Cable Box/Satellite Receiver.
C Use a RF coaxial cable to connect the
TV
jack on the recorder to the
antenna input jack on your TV (VHF/UHF
RF IN.)
D Use the audio/video cables to connect
the VIDEO/AUDIO -EXT1 on the
recorder to the matching VIDEO/AUDIO
output jacks on the Cable Box/Satellite
Receiver.
E Use the audio/video cables to connect
the VIDEO/AUDIO -OUT2 on the
recorder to the matching VIDEO/AUDIO
input jacks on the TV.
TIPS: Before making or changing any connections, make sure that all the devices are disconnected
from the power outlet.
17
Step 2: Optional Connections (continued)
English
Back of a VCR
(Example only)
VHF/UHF
RF IN
CABLE
SATELLITE
VHF/UHF
RF OUT
A
IN
OUT
VIDEO
OUT
VIDEO
IN
AUDIO
L
AUDIO
L
AUDIO
R
AUDIO
R
C
ANTENNA
~
ANTENNA
MAINS
VIDEO
(CVBS)
VIDEO
(CVBS)
Y
S-VIDEO
(Y/C)
L
AUDIO
TV
R
EXT1
PB
L
AUDIO
PR
R
COAXIAL
AUDIO
OUT 2
OUT 1
DIGITAL AUDIO OUT
D
B
TV
AU D IO
O U T
S-V ID E O
IN
V ID E O IN
C Use the audio/video cables to connect
Connecting to a VCR or
other similar device
This connection enables you to record
from a video tape to the HDD or a DVD
recordable disc and allows the VCR to be
used for playback if the recorder is
turned off.
IMPORTANT!
Your new recorder can replace the
VCR for all your recording needs.
Just unplug all the connections to
your VCR.
A Connect the Antenna/Cable TV signal to
the ANTENNA
jack on the recorder.
the VIDEO/AUDIO -EXT1 on the
recorder to the matching VIDEO/AUDIO
output jacks on the VCR.
D Use the audio/video cables to connect
the VIDEO/AUDIO -OUT2 on the
recorder to the matching VIDEO/AUDIO
input jacks on the TV.
Helpful Hints:
– Most commercial video cassettes and
DVDs are copy-protected and therefore
cannot be recorded.
– Connect the recorder directly to the
TV. If there is a VCR or an additional device
in between, the picture quality may be poor
because of the copy protection system built
into the recorder.
B Use a RF coaxial cable to connect the
TV
jack on the recorder to the
antenna input jack on your TV (VHF/UHF
RF IN.)
TIPS: Before making or changing any connections, make sure that all the devices are disconnected
from the power outlet.
18
English
Step 2: Optional Connections (continued)
CABLE
A
IN
RF
VIDEO
OUT
R
AUDIO
L
S-VIDEO
Back of a Cable Box
or Satellite Receiver
F
(Example only)
SATELLITE
B
ANTENNA
D
~
ANTENNA
MAINS
VIDEO
(CVBS)
VIDEO
(CVBS)
Y
S-VIDEO
(Y/C)
L
AUDIO
TV
R
EXT1
Front Panel of
HDD recorder
PB
L
AUDIO
PR
R
COAXIAL
AUDIO
OUT 2
OUT 1
DIGITAL AUDIO OUT
E
C
TV
AU D IO
O U T
S-V ID E O
IN
V ID E O IN
F
VHF/UHF
RF IN
VHF/UHF
RF OUT
IN
OUT
VIDEO
OUT
VIDEO
IN
AUDIO
L
AUDIO
L
AUDIO
R
AUDIO
R
Connecting to a VCR and
Cable Box/Satellite Receiver
A Connect the Antenna/Cable TV signal to
the antenna input (RF IN) jack on the
Cable Box/Satellite Receiver.
B Use the supplied RF coaxial cable to
connect the ANTENNA
jack on the
recorder to the RF OUT jack on the
Cable Box/ Satellite Receiver.
C Use a RF coaxial cable to connect the
TV
jack on the recorder to the
antenna input jack on your TV (VHF/UHF
RF IN.)
S-VIDEO
Back of a VCR
(Example only)
D Use the supplied audio/video cables to
connect the VIDEO/AUDIO -EXT1
jacks on the recorder to the matching
VIDEO/AUDIO output jacks on the
Cable Box/ Satellite Receiver.
E Use the audio/video cables to connect
the VIDEO/AUDIO OUT2 on the
recorder to the matching VIDEO/AUDIO
input jacks on the TV.
F Use another set of audio/video cables to
connect the VIDEO IN/L-AUDIO-R
jacks on the front panel of the recorder
to the to the matching VIDEO/AUDIO
output jacks on the VCR.
TIPS: Before making or changing any connections, make sure that all the devices are disconnected
from the power outlet.
19
Step 2: Optional Connections (continued)
English
DV OUT
L
A
R
B
OR
Connecting a camcorder to
the front jacks
You can use the front jacks to copy
camcorder recordings. These jacks are
located behind the flap on the right hand
side and provides convenient connections
for a camcorder.
Alternatively, you can use the VIDEO
connection if your camcorder has only a
single video output (Composite Video,
CVBS.)
Option 1: Using the DV IN jack
Use this connection if you have a Digital
Video or Digital 8 camcorder. The DV
jack conforms to the i.LINK standard.
It provides the best picture quality.
A Connect the S-VIDEO or VIDEO jack
Use an i.LINK 4-pin cable (not supplied)
to connect the DV IN jack on the
recorder to the appropriate DV OUT
jack on the camcorder.
connect the AUDIO L/R jacks on the
front panel of the recorder to the audio
output jacks on the camcorder.
Before you start operating, press DV on
the remote to select ‘DV’ as the input
channel. For recording, see pages 27~37.
Helpful Hints:
– The DV IN jack does not support a
connection to a Personal Computer.
– It is not possible to record from the
recorder to your camcorder via the DV IN
jack on your recorder.
TIPS:
20
Option 2: Using the S-VIDEO In or
VIDEO In jack
Use the S-VIDEO connection if you have a
Hi8 or S-VHS(C) camcorder. It provides
good picture quality.
on the front panel of the recorder to the
corresponding S-VHS or Video output
jack on the camcorder.
B Use an audio cable (red/white ends) to
Before you start operating, press
SOURCE on the remote control
repeatedly to select ‘CAM1’ or ‘CAM2’
as the input channel, depending on your
connections. For recording, see pages
27~37.
Before making or changing any connections, make sure that all the devices are disconnected from the power
outlet.
IMPORTANT!
When you complete the
connections and turn on the
recorder for the first time, it is
advisable that you make several
basic settings.
English
Step 3: Installation and Setup
Setting your TV channel
programs
Before the recorder can start recording
any TV channel programs, you need to
search for the available TV channels and
store them in this recorder.
Please see the following pages on using
the Setup Menu features to program TV
channels, menu language and system
clock settings. This will improve the
performance of this recorder
considerably.
Note: Ensure that you have successfully
made all the required connections to the
recorder, TV and Satellite Receiver/
Cable Box (if any) and have switched
them on.
Tuner settings can only be changed
when the recorder is not playing or
recording.
Finding the viewing channel
A Press STANDBY-ON 2 on the
recorder to turn it on.
B Turn on the TV and set it to the correct
video-in channel. You should see the blue
DVD background screen.
Usually this channel is between the
lowest and highest channels and may be
called FRONT, A/V IN, VIDEO. See your
TV’s manual for more details.
Or, you may go to Channel 1 on your
TV, then press the Channel down button
repeatedly until you see the Video In
channel.
Or, the TV remote control may have
a button or switch that chooses different
video modes.
SETUP
OK
A Press SETUP on the remote control.
The setup menu appears on the TV.
B Use
keys to highlight
{ SETUP MENU - GENERAL } and
press .
TIPS:
Press to access the options of an item in the menu.
Press SETUP to exit the menu.
21
Step 3: Installation and Setup (continued)
English
GENERAL settings (underlined options are the factory default settings)
Auto Program
Select to start automatic TV channel programming.
SETUP MENU - GENERAL
Auto Chapter Marker
5min.
Record Quality
SP
Auto Program
Search
Manual Program
Edit
Sort
OK
Manual Program
Manual Program
Program Number
Name
Frequency
Fine Tuning
Standard
NICAM
Audio
Skip
OK OK
P001
Ch001
0 5 8 . 9 8 Mhz
PAL B/G
On
Dual A
No
OK
CANCEL
1) Use
keys to highlight { Auto Program - Search } and
press .
A warning message will appear.
2) Select OK OK
and press OK on the remote control
The automatic TV channel search will start. This process may
take several minutes. Once complete, the total number of
channels found will appear on the TV.
Select to modify your preset TV channels.
1) Use
keys to highlight { Manual Program - Edit } and
press .
The modify channel options will be displayed.
2) Use
keys to select one of the options and press
.
{ Program Number } – Use CH+/ CH– to select by the program
number for modifying.
{ Name }
– Use
to select by the channel name for
modifying. Press OK on the remote control to
confirm the selection.
{ Frequency } – Select this to adjust the frequency of the channel.
– Use
keys to search for the next frequency or
use the numeric keypad 0-9 to change the
frequency. Press OK on the remote control to
confirm the setting.
{ Fine Tuning }– Select this to fine-tune the TV channel manually if
the reception is poor.
– Use
keys to fine-tune the frequency.
22
{ Standard }
– Select this to set the system that produces the least
distortion of picture and sound. Press OK on the
remote control to confirm the setting. (See chapter
“TV System Guide” at the back of this manual for
information.)
{ NICAM }
– Select this to receive dual language broadcasts and to
improve the sound quality of the TV channel.
– Use
keys to select { On } or { Off }, then press
OK on the remote control to confirm the setting.
English
Step 3: Installation and Setup (continued)
GENERAL settings (underlined options are the factory default settings)
Manual Program
(continued)
Select to modify your preset TV channels.
{ Audio }
– For dual language broadcasts, select this to switch
between stereo (original) and the additional audio
language.
– Use
keys to select { Dual A } or { Dual B },
then press OK on the remote control to confirm
the setting. This is the default language during timer
recording.
{ Skip }
– Select this to set the channel to be skipped. The
skipped channels can only be accessed by pressing
the corresponding number button on the remote
control.
– Use
keys to select { Yes } if you wish to skip
the channel and press OK on the remote control to
confirm the setting.
3) To confirm all the changes, select OK OK
and press OK on
the remote control to exit to the previous screen.
Sort
Select to sort your stored TV channels.
1) Use
Sort
OK
OK
CANCEL
P001
P002
P003
P004
P005
P006
P007
P008
BC020
SW006
CH008
CH004
GG006
CH010
CH012
CH005
keys to highlight { Sort - OK } and press
.
The list of TV channel programmes appears.
P009 CH001
2) Use
press
keys to highlight the channel you want to shift and
.
The selected channel will move to the right side of the screen.
3) Use
keys to shift the TV channel to the desired position,
and press OK on the remote
Use
to highlight OK OK
control.
The selected channel will be inserted before the current position.
To cancel the change, highlight
OK
CANCEL
and press OK.
4) Repeat steps 2~3 until you have sorted all the TV channels you
want.
23
Step 3: Installation and Setup (continued)
English
Setting the language
Setting the time & date
You can select the language for subtitles
and audio for DVD playback. For some
DVDs, the subtitle/audio language can
only be changed via the DVD disc menu.
If the selected language is not available on
the disc, the disc’s default language will be
used instead.
If the recorder has not set the time and
date correctly, set the clock manually by
following the steps below.
A Press SETUP.
The setup menu appears.
B Use
keys to highlight
{ SETUP MENU - DATE / TIME} and
press to access the menu.
The menu language (on-screen display)
for the system will remain as you set it.
SETUP MENU - DATE / TIME
Language settings can only be
changed when the recorder is not
playing or recording.
Date(dd/mm/yyyy)
31 12 2005
Time(hh:mm)
15 : 33
A Press SETUP.
The setup menu appears.
B Use
keys to highlight
{ SETUP MENU - LANGUAGE } and
press to access the menu.
C Use
keys to highlight one of the
options and press to access the
options.
SETUP MENU - LANGUAGE
System Language
English
Audio Language
English
Subtitle Language
Off
Disc Menu Language
English
If the recorder has not set the time and
date correctly, you can further adjust the
clock settings, see next page for details.
D Once complete, press
previous menu.
E Press SETUP to exit.
C Use
keys to highlight one of the
options and press . See next page for
details.
D Use
keys to highlight the desired
setting and press OK to confirm.
TIPS:
24
Press to access the options of an item in the menu.
Press SETUP to exit the menu.
to return to the
English
Step 3: Installation and Setup (continued)
LANGUAGE settings (underlined options are the factory default settings)
System Language
Selects the menu language for this recorder on-screen display.
Audio Language
Selects the preferred audio language for DVD playback.
Subtitle Language
Selects the preferred subtitle language for DVD playback.
Disc Menu Language Selects the preferred disc menu language for DVD playback
Helpful Hints:
– If the selected audio/subtitle language is not available on the disc, the disc’s
default setting language will be used instead.
– For some DVDs, the subtitle/audio language can only be changed via the DVD
disc menu.
DATE/ TIME settings (underlined options are the factory default settings)
Date (dd/mm/yy)
Use
keys to change the number and use
keys to
select different entry fields, then press OK to confirm.
Time (hh/mm)
Use
keys to change the number and use
keys to
select different entry fields, then press OK to confirm.
The basic installation is now complete. This recorder is ready for use!
25
Control TV programs
English
Switching on to TV program
CH + /
Pause live TV function
You may be interrupted whilst watching
your favourite TV program. You can
pause the show by pressing PAUSEÅ
and pressing PLAYÉto resume
playback of the program at the scene it
was interrupted. You can ‘pause’ the live
TV broadcast up to a maximum period of
3 hours. It behaves exactly as if you were
in control of the live broadcast.
TUNER
If you want to return to the live TV
program, press and holdÉ.
A Turn on the TV to the correct program
number for the recorder (e.g. ‘EXT’, ‘0’,
‘AV’).
B Press STANDBY-ON 2 to turn on
the recorder.
If no TV program appears on the
screen, press TUNER on the remote
control.
C Press CH +/- to select a TV channel.
The selected TV channel will appear
on the status window.
The active TV programs will be stored
automatically to the temporary
HDD storage in this recorder. This
information is shown on the Time Shift
video bar.
Instant Replay function
Whilst watching a live TV program, you
can pressÑon the remote control to
jump back 10 seconds upon every single
press for instant replay.
If you want to return to the live TV
program, press and holdÉ.
To display or remove the Time Shift
video bar, press the m key repeatedly.
07:15:36
10:15:36
LIVE
For more information about the
temporary HDD storage (Time
Shift Buffe), see next page.
TIPS:
26
Press m to display the time shift video bar or help text.
About temporary HDD
storage (Time Shift Buffer)
As soon as you switch on this recorder,
the currently selected TV program will
be stored in a temporary hard disk
storage called ‘Time Shift Buffer’ (TSB),
up to 3 hours of programs.
In tuner mode, the Time Shift video bar
will appear on the screen, it indicates the
status and timing of the TV programs
stored in the temporary HDD storage.
You can choose to display or remove the
video bar by pressing the m key on the
remote control.
a
b
07:15:36
WARNING!
The TV programs stored in the
temporary HDD storage will be deleted
once it has exceeded the storage buffer
or when you press STANDBY-ON 2
to turn off the recorder.
In addition, executing the following
actions will also clear the contents in the
temporary HDD storage:
Press DV, DVD REC or SOURCE on
the remote control.
OR
Use the option { Delete HDD } to
erase all contents of your hard disk
storage. See “Before Recording – HDD
Settings” for details.
10:15:36
LIVE
c
d
The Time Shift video bar consists of the
following information :
a Content temporarily saved in the time
shift buffer.
b The TV program start time.
Once it has exceeded 3 hours, the
content stored at the beginning will be
deleted and the start time will be updated
accordingly.
c Status of source of video input.
“LIVE” or the time of current playback
being viewed “HH:MM:SS”.
d Icon which shows the status of the time
shift buffer.
– playback of content stored in the
time shift buffer.
– marks the beginning of content
recording.
– marks the current recording in
progress.
– the current screen has been paused
from playback. (This will not pause
recording.)
TIPS:
Press m to display the time shift video bar or help text.
27
English
Before Recording
Before Recording (continued)
English
Accessing the HDD (Hard
Disk Storage) Setup Menu
You can preset the behavior of your hard
disk storage of the recorder. This
recorder offers various options for easy
management of your hard disk recording.
OK
SETUP
A Press SETUP.
The system setup menu appears.
B Use
keys to highlight
{ SETUP MENU - HDD } and press
to access the menu.
SETUP MENU - HDD
C Use
press
Save Time Shift Buffer
No
HDD Info
Show
Space Management
Automatic
Delete HDD
OK
Delete Optical Disc
OK
keys to highlight the option and
to access its options.
D To exit, press
TIPS:
28
.
Press to go back to the previous menu item.
Press SETUP to exit the menu.
English
Before Recording (continued)
HDD settings (underlined options are the factory default settings)
Save Time Shift
Buffer
HDD Info
This option allows you to control the behavior of the Time Shift
Buffer.
{ Yes }
– Select to retain the contents in the temporary HDD
storage when you switch the tuner’s TV channel or
external video input source.
{ No }
– Select to clear the contents in the temporary HDD
storage.
Press OK to display information on:
–
–
–
–
Space Management
Hard disk size in MB ( Megabytes).
Used space in MB ( Megabytes).
Remaining space in MB ( Megabytes).
Number of titles stored on the HDD.
This option determines how the recorder will respond when
the HDD is full of recordings.
{ Automatic }–During recording, when the HDD is full, the
recorder will proceed to overwrite any unprotected
recordings in the HDD. The oldest unprotected
recordings will be deleted first.
{ Manual }
Delete HDD
– During recording, when the HDD is full, recording
will be stopped. A warning message { The hard disk
is full. Please erase some programs to allow
further recording. } will appear on the screen.
This option will erase all marked/ unmarked recordings on the
HDD. This option is not available when recording to HDD is in
progress.
Press to highlight OK.
A warning message will appear. Select OK OK
to proceed or
OK
CANCEL
to abort. Once complete, the recorder will switch to standby
mode.
Delete Optical Disc
This option will erase all content on a DVD±RW disc, including
those that were not recorded on this recorder. This option
is only available in tuner mode.
Press to highlight OK.
A warning message will appear. Select
OK
CANCEL
to abort.
OK OK
to proceed or
29
Before Recording (continued)
English
Default Recording settings
The default recording settings will allow
you to preset auto chapter markers and
the preferred mode of recording quality
for HDD recording.
A Press SETUP on the remote control.
The setup menu appears on the TV.
B Use
keys to highlight
{ SETUP MENU - GENERAL } and
press to confirm.
SETUP MENU - GENERAL
Auto Chapter Marker
5min.
Record Quality
SP
Auto Program
Search
Manual Program
Edit
Sort
OK
C Use
keys to select the setting you
wish to change and press OK to confirm.
Instructions and explanation of the
options are provided in the following
pages.
D To exit, press SETUP.
Auto Chapter Markers
You can insert chapter markers within a
title during recording. This allows you to
access to specific points on the
recording.
A Use
keys to highlight { Auto
Chapter Marker } and press to
access its options.
B Use
keys to select your preferred
setting.
C Press OK to confirm.
Default Recording Quality
The setting defines the picture quality of
recordings and the maximum recording
time on the HDD.
Important! When copying from the
HDD to a DVD recordable disc, the
mode of record quality for the selected
recording in the HDD will automatically
be transferred, selecting another mode of
record quality is not possible.
A Use
keys to highlight { Record
Quality } and press to access its
options.
B Use
keys to select your preferred
mode of record quality.
C Press OK to confirm.
TIPS:
30
Press to go back to previous menu item.
Press SETUP to exit the menu.
GENERAL settings (underlined options are the factory default settings)
Auto Chapter
Markers
You can insert chapter markers within a title during recording.
This lets you access to specific points on the recording.
Press
to access the menu and use
options.
{ 5min. }
{ 10min. }
{ 20min. }
{ 30min. }
{ Off }
Record Quality
keys to select one of the
– Chapter markers are inserted during recording at
every 5 minutes interval.
– Chapter markers are inserted during recording at
every 10 minutes interval.
– Chapter markers are inserted during recording at
every 20 minutes interval.
– Chapter markers are inserted during recording at
every 30 minutes interval.
– The feature is disabled.
Select this option to preset your preferred mode of record
quality.
Press to access the menu and use
options.
Record Quality
HQ High Quality
SP Standard Play
SP+ Standard Play Plus
LP Long Play
EP Extended Play
SLP Super Long Play
keys to select one of the
Hours of Recording that can be stored
DVDR3360H
160GB HDD
34
DVDR3370H
250GB HDD
53
DVD±R/
DVD±RW
1
68
85
106
132
2
2.5
102
136
159
212.5
204
318
3
4
6
Values are estimates only. Parts of the HDD storage capacity will be reserved for
the operations of this recorder and time shifting.
Auto Program
Select to make automatic TV channel programming.
See section “Step 3: Installation and Setup – Setting your TV
channel programs”.
Manual Program
Select to modify your preset TV channels.
See section “Step 3: Installation and Setup – Setting your TV
channel programs”.
Sort
Select to sort your stored TV channels.
See section “Step 3: Installation and Setup – Setting your TV
channel programs”.
31
English
Before Recording (continued)
Record on Hard Disk
English
IMPORTANT!
Unrecordable pictures
Television programs, films, video tapes,
discs, and other materials may be
copy-protected and therefore cannot be
recorded on this recorder.
Recording from a DV
camcorder
You can record video directly from a
connected DV camcorder onto the
HDD, where you can edit it easily and
copy to a recordable DVD if required.
Recording TV programs
Follow the instructions below to record
TV programs onto the HDD, where you
can store for future viewing or copy to a
DVD recordable disc if required.
CH
A In tuner mode, press the m key on the
remote control to display the time shift
video bar.
B Use . / > keys to search for the
beginning of the scene in the temporary
HDD storage where you want to start
recording.
STOP
REC
PAUSE
DV
C Press RECâ on the remote control to
start recording.
To cancel, press SELECT.
To save all current programs stored in
the time shift buffer, press and hold
RECâ.
IMPORTANT!
– If you press DV on the remote
control, the unmarked contents in
the TSB will be removed.
D To stop recording, press STOPÇon the
remote control.
To record directly to a recordable
DVD disc, see page 35.
TIPS:
32
Set the appropriate mode of record quality for HDD recording. The same record quality will be transferred
from HDD to a recordable DVD, see page 30~31.
A Connect the DV camcorder to the
DV IN jack on the front panel of this
recorder.
B Find the footage on the DV camcorder
that you want to start recording from
and set the camcorder to pause mode.
C Turn on the TV to the correct program
number for the recorder (e.g. ‘EXT’, ‘0’,
‘AV’.)
D Turn on the recorder and press DV on
the remote control.
An information box will be displayed.
System State: Stop DV State: Stop
Record to Hard Disk As Standard Play
Elapsed Time: 00:00:00 Remaining Time: 00:00:00
Recording from an external
device (Camcorder/VCR/
DVD player)
A copy protection system has been built
into this recorder to prevent the transfer
of data from pre-recorded DVDs or
other copy protected material onto the
recordable DVD. You can only store the
contents in the temporary HDD storage
of this recorder.
Note: Set the preferred mode of record
quality before proceeding, see “Before
Recording - Default Recording Settings.”
Press SELECT repeatedly to change the
mode of record quality.
E Press RECâ to start recording and
PAUSE
press the PLAY button on the DV
camcorder to start playback.
To pause the recording, press PAUSE Å.
To resume recording, press PLAY
again.
A new chapter marker is created
after recording restarts.
F To stop recording, press STOPÇ.
A new title will be created when you
begin another recording.
English
Record on Hard Disk (continued)
REC
SOURCE
TUNER
A Connect the external device to this
recorder (see pages 17 ~ 20).
B Turn on the TV to the correct program
number for the recorder (e.g. ‘EXT’, ‘0’,
‘AV’).
C Press STANDBY-ON 2 to turn on
To record directly to a recordable
DVD disc, see page 35.
the recorder.
If no TV program appears on the
screen, press TUNER on the remote
control.
D Press SOURCE repeatedly to select the
correct input channel that matches the
connected jack of the device.
– { EXT 1 } : EXT 1 jack at the back.
– { CAM 1 } : VIDEO jack on the
front.
– { CAM 2 } : S-VIDEO jack on the
front.
TIPS:
Set the appropriate mode of record quality for HDD recording. The same record quality will be transferred
from HDD to a recordable DVD, see page 30~31.
33
Record on Hard Disk (continued)
English
E Press RECâ to start recording.
You can also press RECâ
repeatedly to increase the recording time
in 30-minute increments.
F Start playback on the connected device.
The content on the connected device
will be recorded.
G To stop the recording before the
scheduled ending, press STOPÇ.
To record directly to a recordable
DVD disc, see page 35.
TIPS:
34
Set the appropriate mode of record quality for HDD recording. The same record quality will be transferred
from HDD to a recordable DVD, see page 30~31.
IMPORTANT!
Unrecordable pictures
Television programs, films, video tapes,
discs, and other materials may be copyprotected and therefore cannot be
recorded on this recorder.
Copying from HDD to a
recordable DVD
You can copy a recorded title(s) from the
HDD (hard disk drive) to a recordable
DVD disc.
The time taken to copy content from the
HDD to a recordable DVD depends on
the record quality of the HDD
recordings.
It is not possible to change the mode of
record quality during the copying
process. As such, it is important that you
choose the appropriate record quality
when you first set up the recording to
the HDD.
The copying process is done at a higher
speed than the recording.
Discs for recording
There are several formats of DVD
recordable discs which can be used with
this recorder:
DVD±RW (DVD ReWritable discs)
– Discs that are rewritable can be used
for multiple recordings once the existing
data has been erased.
DVD±R (DVD Recordable discs)
– Discs that can only be used for a single
recording. Each new recording is always
added at the end of all previous
recordings as existing recordings cannot
be overwritten.
– Editing can be made on DVD±R discs
as long as they have not been finalized.
– To play a DVD±R disc on another
DVD player, it must be finalized (see page
56.) After this is done, no more content
can be added to the disc.
The following information will be stored
on the disc :
– Title/name of recording
– Date of recording
– Time of recording
– Record quality mode/ length of
recording
– Index picture of title
TIPS:
Ensure that there is sufficient space available on the DVD±R before recording.
You have to finalize the DVD±R before it can be played on other players, see page 56.
35
English
Record on DVD Recordable Disc
Record on DVD Recordable Disc (continued)
English
Recording from various
sources
You can choose to copy your recordings
from the HDD or an external device to a
DVD recordable disc. The storage
capacity of the disc depends on the
record quality that was selected for the
recording in the recorder or device, see
page 30.
Recording from the HDD
A Turn on the TV to the correct program
number for the recorder (e.g. ‘EXT’, ‘0’,
‘AV’).
B Insert a DVD recordable disc into the
recorder.
C Press HDD on the remote control.
The HDD content menu appears on
the screen.
HDD 16 Titles
No Ch.
001 CH001
002 CH003
003 CH009
004 CH004
005 CH002
006 CH008
007 CH012
008 CH010
Date
20/05/05
14/05/05
25/04/05
30/04/05
28/03/05
12/04/05
05/08/05
30/06/05
Time
14.00
16.00
20.30
03.30
08.30
11.00
21.30
22.30
25%
Title
Travel
News
Drama
Nature
News
Title 3
News
Discover
For other options, press [DVD], [DV],
[TUNER] keys. Press [RIGHT] to edit menu.
STOP
PAUSE
SELECT
HDD
00:20:20
SP PAL
1. Press [SELECT] to
mark or unmark
recordings.
2. Press [HDD] to
copy selected
recordings to DVD.
Press [SHUFFLE] to
sort by title.
REC
DVD REC
SOURCE
DV
D Use
keys to highlight the title/titles
and press SELECT to mark the titles to
copy to DVD.
If you have many HDD title recordings,
use .( fast reverse) or > (fast
forward) to view the previous/ next page of
HDD titles for selection.
E Press HDD on the remote control.
Recording to the DVD recordable disc
will begin. The dubbing icon
will be
displayed at the bottom right corner of
the screen.
Once complete, the icon will not be
shown.
F To stop recording, press STOPÇ on
the remote control.
Helpful Hint:
– During selection of recordings for copying,
press SHUFFLE on the remote control to sort
according to the titles of recording.
TIPS:
36
Ensure that there is sufficient space available on the DVD±R before recording.
You have to finalize the DVD±R before it can be played on other players, see page 56.
Record on DVD Recordable Disc (continued)
A Turn on the TV to the correct program
number for the recorder (e.g. ‘EXT’, ‘0’,
‘AV’).
B Insert a DVD recordable disc into the
recorder.
C Press DVD REC to switch to direct
recording mode.
An information box will be displayed
on the screen.
System State: Stop
Record to Optical Disc As Standard Play Plus
Elapsed Time: 00:00:00 Remaining Time: 00:00:00
E Press SELECT to toggle between the
English
Recording from an external device/
VCR/ DV Camcorder
different modes of record quality.
Record Quality
HQ High Quality
SP Standard Play
SP+ Standard Play Plus
LP Long Play
EP Extended Play
SLP Super Long Play
Hours of Recording that can be stored
DVDR3360H
160GB HDD
34
68
DVDR3370H
250GB HDD
53
106
DVD±R/
DVD±RW
1
2
85
102
132
159
2.5
3
136
204
212.5
318
4
6
Values are estimates only. Parts of the HDD storage capacity will be reserved for
the operations of this recorder and time shifting.
F Press RECâon the remote control.
Recording to the DVD recordable disc
will be begin.
G To stop recording, press STOPÇ on
the remote control.
D Press SOURCE repeatedly to select
from the various options:
{ Tuner }
Input source from TV programs.
Helpful Hint:
– All title selections and settings will be lost
once you replace or remove the recordable
DVD.
{ CAM 1 }
Input source from the device connected to the
VIDEO and AUDIO L/R jacks on the front
panel.
To edit your recordings on the
DVD recordable disc, see pages
54~61.
{ CAM 2 }
Input source from the device connected to the
S-VIDEO and AUDIO L/R jacks on the front
panel.
{ EXT 1 }
Input source from the device connected to the
VIDEO (CVBS)-IN-EXT and AUDIO L/R jacks
on the back panel.
OR
Press DV to record from the DV
camcorder connected to the DV IN jack on
the front panel.
TIPS:
Ensure that there is sufficient space available on the DVD±R before recording.
You have to finalize the DVD±R before it can be played on other players, see page 56.
37
Timer Recording
English
Timer recording (G-CODE®
System)
About timer recording
Use ‘Timer Recording’ to automatically
start and stop a recording at a later
date/ time. The recorder will tune to the
right program channel and begin
recording at the specified time.
With this recorder, you can pre-program
up to 20 recordings.
To make a timer recording, your
recorder needs to know:
– The date you want to make the
recording.
– The recording input source.
– The start and stop time of the
recording.
– The mode of record quality, see
page 31.
This is a simple programming system for
recorders. To use it, enter the G-CODE®
programming number associated with
your television program. You can find
this number in your TV listings magazine.
All the information needed by the
recorder for programming is contained in
the programming number.
A Turn on the TV power. Select the
correct Video In channel at the TV.
If you are recording directly to a
DVD disc, insert the DVD recordable
disc before proceeding to step B.
B Press TIMER on the remote control.
The timer schedule list appears.
Timer Schedule
Source Rec Mode Date
Start
End Rec To
1
2
3
4
OK
5
6
SELECT
TIMER
C Use
keys to highlight the next
available empty slot and press OK.
The G-CODE® System setup menu
appears.
G-CODE System
Enter the G-CODE programming
number for the show you wish to
record. Press CANCEL for manual
timer recording. To go back to timer
schedule press [RETURN].
OK
CONFIRM
TIPS:
38
OK
CANCEL
Set the appropriate mode of record quality for HDD recording, the same record quality will be transferred
from HDD to a recordable DVD.
Timer Recording (continued)
– Use
keys or the numeric keypad
0-9 to enter the end time of recording.
the G-CODE® programming number for
the show you wish to record and press
OK. (e.g. : 5-312-4 or 5,312 4, key in
‘53124’.)
{ Title }
®
To cancel the G-CODE programming, use
OK
keys to select CANCEL
in the menu
and press OK.
E To confirm your entry, select
OK
CONFIRM
in
the menu and press OK.
The timer editor menu appears.
OK OK
– Use
keys to select the
alphanumeric options to enter the title of your
recording.
G Select
OK OK
in the menu and press
OK.
The system will store the timer entry
and return to the timer schedule list.
H Press TIMER to exit the menu.
Timer Editor
Source
Rec To
Rec Mode
Mode
Date
Start
End
Title
{ End }
English
D Use the numeric keypad 0-9 to enter
Ch003
HDD
SP
Once
31 / 01 / 0 5
21 : 3 3
22 : 0 3
MyTitle0
OK
CANCEL
I Press STANDBY-ON2 to turn off
the recorder.
If the recorder is not in standby mode,
a warning message will appear three
minutes before the recording starts.
The ‘TIMER’ icon will light up on the
display panel if a timer recording is set.
F Use
keys to select an entry in the
menu and press to enter its options.
{ Source }
– Use
source.
keys to select the recording input
{ Rec To }
– Use
keys to select { HDD } or
{ DVD } to enter the recording destination.
{ Rec Mode }
– Use
keys to select your option.
{ Mode }
– Use
keys to select { Once },
{ Daily }, { Weekly }.
{ Date }
– Use
keys or the numeric keypad
0-9 to enter the date for recording.
{ Start }
– Use
keys or the numeric keypad
0-9 to enter the start time of recording.
TIPS:
Set the appropriate mode of record quality for HDD recording, the same record quality will be transferred
from HDD to a recordable DVD.
39
Timer Recording (continued)
English
Timer recording (manually)
D Select
OK
in the menu and press
CANCEL
OK.
The timer editor menu appears.
A Turn on the TV power. Select the
Timer Editor
correct Video In channel at the TV.
Source
Rec To
Rec Mode
Mode
Date
Start
End
Title
If you are recording directly to a
DVD disc, insert the DVD recordable
disc before proceeding to step B.
B Press TIMER on the remote control.
The timer schedule list appears.
OK OK
Timer Schedule
Source Rec Mode Date
Start
End Rec To
1
2
Ch003
HDD
SP
Once
31 / 01 / 0 5
21 : 3 3
22 : 0 3
MyTitle0
OK
CANCEL
E Use
keys to select an entry in the
menu and press to enter its options.
{ Source }
3
– Use
source.
4
5
keys to select the recording input
{ Rec To }
6
C Use
keys to highlight the next
available empty slot and press OK.
The G-CODE® System setup menu
appears.
G-CODE System
Enter the G-CODE programming
number for the show you wish to
record. Press CANCEL for manual
timer recording. To go back to timer
schedule press [RETURN].
– Use
keys to select { HDD } or
{ DVD } to enter the recording destination.
{ Rec Mode }
– Use
keys to select your option.
{ Mode }
– Use
keys to select { Once },
{ Daily }, { Weekly }.
{ Date }
– Use
keys or the numeric keypad
0-9 to enter the date for recording.
{ Start }
OK
CONFIRM
OK
CANCEL
– Use
keys or the numeric keypad
0-9 to enter the start time of recording.
{ End }
– Use
keys or the numeric keypad
0-9 to enter the end time of recording.
{ Title }
– Use
keys to select the
alphanumeric options to enter the title of your
recording.
F Select
OK OK
in the menu and press
OK.
The system will store the timer entry
and return to the timer schedule list.
TIPS:
40
Set the appropriate mode of record quality for HDD recording, the same record quality will be transferred
from HDD to a recordable DVD.
To cancel the above timer setting, press
SELECT on the remote control.
G Press TIMER to exit the menu.
H Press STANDBY-ON 2 to turn off
the recorder.
If the recorder is not in standby mode,
a warning message will appear three
minutes before the recording starts.
The ‘TIMER’ icon will light up on the
display panel if a timer recording is set.
English
Timer Recording (continued)
Changing/ Deleting a timer
recording
A Turn on the TV power. Select the
correct Video In channel at the TV.
B Press TIMER on the remote control.
The timer schedule list appears.
Timer Schedule
Source Rec Mode Date
Helpful Hint:
– Set the timer recording one minute ahead
of the program’s start time. This helps
ensure the entire program is recorded as
the disc requires about 30 seconds to
prepare for recording.
Start
End Rec To
1 CH003
SP
31/01/05 21.33
22.03
HDD
2 EXT 1
EP
25/04/05 16.00
17.30
DVD
3 CH008
SP
30/01/05 10.00
11.15
HDD
4
5
6
C Use
keys to select a timer program
which you want to change/ delete.
Setting a timer recording from an
external Cable Box/
Satellite Receiver
If you have a Satellite Receiver/Cable Box
connected to this recorder via the
VIDEO (CVBS) (see page 17,) follow the
steps described below to program the
recordings.
A Select the channel you want to record at
the Satellite Receiver/Cable Box.
B Program the recording with the required
information. Follow the steps A~D of
“Timer Recording (manually)” on the
previous page.
When selecting options for { Source }
choose { EXT 1 } as the input channel
and press OK to confirm.
C Keep the Satellite Receiver/Cable Box
switched on for the recording.
D To delete the timer entry, press
SELECT on the remote control.
E To change the timer schedule, press
OK to enter the timer editor menu of
the selected timer program.
Timer Editor
Source
Rec To
Rec Mode
Mode
Date
Start
End
Title
OK OK
Ch003
HDD
SP
Once
31 / 01 / 0 5
21 : 3 3
22 : 0 3
MyTitle0
OK
CANCEL
F Select the entry field and make the
necessary changes.
G Once complete, select
OK OK
in the
menu and press OK to save the changes.
H Press TIMER to exit the menu.
D Press STANDBY-ON 2 to turn off
the recorder.
TIPS:
Set the appropriate mode of record quality for HDD recording, the same record quality will be transferred
from HDD to a recordable DVD.
41
Playback from Hard Disk
English
Playback your HDD
recordings
Each recording stored on the HDD is
displayed in the HDD content menu with
an index picture.
00:00:00
01:15:30
00:38:36
A Press HDD on the remote control.
The HDD content menu appears.
B Use
keys to highlight a title and
press OK on the remote control to start
playback.
If you have many HDD title recordings,
use .( fast reverse) or > (fast
forward) to view the previous/ next page of
HDD titles for selection.
Date
20/05/05
14/05/05
25/04/05
30/04/05
28/03/05
12/04/05
05/08/05
30/06/05
Time
14.00
16.00
20.30
03.30
08.30
11.00
21.30
22.30
– jump forward by 30 seconds.
– jump backward by 10 seconds.
HDD 16 Titles
No Ch.
001 CH001
002 CH003
003 CH009
004 CH004
005 CH002
006 CH008
007 CH012
008 CH010
.>
– move to the beginning or previous/ next
chapter.
– hold down this button to start fast
backward/ forward search, press the button
again to increase the search speed.
Title
Travel
News
Drama
Nature
News
Title 3
News
Discover
For other options, press [DVD], [DV],
[TUNER] keys. Press [RIGHT] to edit menu.
PLAY
00:20:20
SP PAL
1. Press [SELECT] to
mark or unmark
recordings.
2. Press [HDD] to
copy selected
recordings to DVD.
Press [SHUFFLE] to
sort by title.
C During playback, you can use the
following keys on the remote control to
access additional playback features.
– starts playback
PAUSE Å
– view a still picture.
m
– displays the Time Shift video bar. Press
repeatedly to remove the video bar display.
– displays the help text for the selected
function.
STOPÇ
– stop playback.
ZOOM
– zoom in and out of a still/paused picture.
STOP
PAUSE
ZOOM
42
PLAY
Helpful Hint:
– During selection of recordings for
playback, press SHUFFLE on the remote
control to sort according to the titles of
recording.
Playable discs
Using this recorder, you can play and
record on the following discs:
Recording and Playback
DVD±RW
(DVD ReWritable);
can be recorded on
and overwritten repeatedly.
DVD±R
(DVD Recordable);
can be recorded on
only once.
IMPORTANT!
– If the inhibit icon (
Error )
appears on the TV screen when a
button is pressed, it means the
function is not available on the
current disc or at the current time.
– DVD discs and players are
designed with regional restrictions.
Before playing a disc, make sure the
disc is for the same region as your
player.
– Do not push on the disc tray or
put any objects other than discs on
the disc tray. It may cause the disc
player to malfunction.
Playback only:
Inserting a disc
DVD Video
(Digital Versatile Disc)
A Press STANDBY-ON 2 to turn on
CD-RW (CD-ReWritable)
Audio/ MP3/ JPEG contents
the recorder.
ReWritable
CD-R (CD-Recordable)
Audio/ MP3/ JPEG contents
Audio CD (Compact Disc
Digital Audio)
MP3-Disc
Video CD
(Formats 1.0, 1.1, 2.0)
Super Video CD
DivX Disc
(DivX 3.11, 4.x, 5.x)
TIPS:
B Press OPEN CLOSE ç on the front of
the recorder.
The disc tray opens.
Recordable
C Carefully place the disc onto the tray
with the label facing up, then press
OPEN CLOSEç.
Make sure the disc label is facing up.
For double-sided discs, load the disc as
indicated on the label.
D Turn on the TV power. Select the
correct Video In channel at the TV (see
page 21.)
E Playback will start automatically or a
dialog will appear on the TV (see next
page.)
Some discs cannot be played on this recorder due to the configuration and characteristics of the disc,
or due to the condition of recording and authoring software.
43
English
Playback from Disc
Playback from Disc (continued)
English
Starting disc playback
Press DVD on the remote control.
Playback will begin automatically. If the
disc has its own menu this will be loaded,
otherwise the recorder will launch an
index screen.
If the pin code entry dialog appears on
the TV, this means that the parental
control was activated for the inserted
disc (see page 64.)
Use the numeric keypad 0-9 on the
remote control to enter your pin code
(password.)
For more playback features, see pages
47~50 “Additional Playback Features”.
Playing a DVD video disc
The DVD disc is usually formatted with a
disc menu. You may have to make your
selection (e.g., subtitle or audio language)
within the disc menu.
A Insert a DVD disc. Press DVD on the
remote control.
If the disc menu appears on the TV
Use the numeric keypad 0-9 to input
your selection or use
keys to
select a play option and press OK to
start playback.
Playing a (Super) Video CD
(Super) Video CDs may feature ‘PBC’
(Play Back Control.) This allows you to
play the video CDs interactively,
following the menu on the display.
A Insert a (Super) Video CD. Press DVD
on the remote control.
If the ‘PBC’ is on, the disc index
menu will appear on the TV
B Use numeric keypad 0-9 to input your
selection or to select a play option.
Press RETURN on the remote control
to return to the previous menu.
To turn on/off the Playback Control
mode, press m key on the remote
control twice during playback to access
the playback menu options.
Use
keys to select { PBC } and
press to select either { PBC On } or
{ PBC Off }.
C To stop playback, press STOP .
Playing an audio CD
A Insert an audio CD. Press DVD on the
remote control.
Playback starts automatically.
B To stop playback, press STOP .
To select a specific chapter/title
marker
During playback, press T/C on the
remote control repeatedly to toggle
bewteen { Title }, { Chapter } or
{ Time }. Use the numeric keypad 0-9
to input your selection of title/chapter
number or specific time during playback.
B To stop playback, press STOP .
TIPS:
44
Some discs cannot be played on this recorder due to the configuration and characteristics of the disc,
or due to the condition of recording and authoring software.
Playback from Disc (continued)
A Insert a recorded DVD±R/±RW disc.
Press DVD on the remote control.
The Index Picture screen appears.
B Use
PLAY
Playing a MP3 disc
A Insert a MP3 CD. Press DVD on the
remote control.
The disc content menu appears.
keys to select a title and press
to start playback.
File Play - Stop 0:00:00/ 0:00:00
Directory
C To stop playback, press STOP .
1
2
3
4
5
6
7
8
Helpful Hint:
– If the message ‘BLANK’ appears on the
display panel, this means that there are no
recordings on this disc.
Playing a DivX disc
This recorder supports the playback of
DivX movies which you can copy from
your computer onto a CD-R/RW or
DVD±R/±RW disc.
A Insert a DivX disc. Press DVD on the
remote control.
The disc content menu appears.
If the DivX movie contains external
subtitles, you have to first select the
subtitle file from the file list.
Use
keys to select the files for
playback and press SELECT to confirm
your selection.
B Press PLAY
to start playback.
During playback, you can press m on
the remote control to display the disc
content menu.
Helpful Hints:
– Subtitle files with the following filename
extensions (.srt, .smi, .sub, .sami) are
supported.
– It is normal to experience an occasional
pixelation during MPEG-4/DivX playback
due to poor encoding of the content.
TIPS:
English
Playing a DVD±R/±RW disc
Playlist
Bee Gees
Phil Collins
Bryan Adams
Collin Raye
Nat King Cole
UB40
Jordan Hill
Faith Hill
Note: It may require a longer time for
the recorder to display the disc content
menu on the TV due to the large number
of songs/pictures compiled into one disc.
B Use
keys to navigate within the menu
and press OK to access the folder/ album.
C Use
keys to select the track/file to
play.
To go to the previous menu, press
RETURN.
D To create a playlist, highlight the track/file
and press SELECT.
The selected tracks/files will appear
on the right screen.
Use
keys to toggle between the
left and right screens.
E Press PLAY
to start playback.
F During playback, you can press ./
> to select the next/previous track.
G To stop playback, press STOP .
Helpful Hints:
– Only the first session of a multi-session
CD will play back.
– It is normal to experience an occasional
“skip” while listening to your MP3 disc.
– Further album, track and artist information
will also be displayed on the TV if included in
the ID tag.
Some discs cannot be played on this recorder due to the configuration and characteristics of the disc,
or due to the condition of recording and authoring software.
45
Playback from Disc (continued)
English
Playing a picture disc (or musical
slide show)
You can display JPEG pictures in the
selected roll automatically one after the
other.
A Insert a JPEG picture disc (CD,
CD-R/RW, DVD.) Press DVD on the
remote control.
The disc content menu appears.
B Use
keys to navigate within the
menu and press OK to access the folder/
album.
C To create a playlist, highlight the track/file
and press SELECT.
The selected tracks/files will appear
on the right screen.
To remove the track/file from the
playlist, press SELECT once.
D You can select to playback from the
original disc content or from the playlist,
just use
keys to move to the correct
screen before selecting the track/file for
playback.
File Play - Stop 0:00:00/ 0:00:00
Directory
1
2
3
4
Japan trip
Bryan Bday
My songs
Hot Hits
Playlist
File Play - Stop 0:00:00/ 0:00:00
Directory
Playlist
..\
1
2
3
4
5
6
7
8
P1010001.JPG
P1010008.JPG
BUTTER-1.JPG
NATURE-1.JPG
BUTTER-1.JPG
P1022500.JPG
P1023000.JPG
MERLIO-1.JPG
E During playback, you can press m on
the remote control to access various
settings for the slide show playback.
File Play
Type
Mode
Trick
Wipe
Zoom
Rotate
PIC
Normal
Play
Top to bottom
Fitscreen
Clockwise 0
Top to bottom
Down to top
Left to right
Right to left
Extend center V.
Press ZOOM on the remote control to
enlarge the picture.
F To stop playback, press STOP .
Playable JPEG picture disc
This recorder can read JPEG pictures
stored on a CD-ROM, Picture CD, or
DVD.
File format:
– The file extension has to be ‘.JPG,’
‘.JPE’ or ‘.JPEG.’
– It can only display DCF-standard still
pictures or JPEG pictures e.g. TIFF. It
cannot play back moving pictures, Motion
JPEG, progressive JPEG and other
formats, or pictures in formats other
than JPEG, or pictures associated with
sound.
– It may require a longer time for the
recorder to display the disc content on
the TV due to the large number of songs/
pictures compiled onto one disc.
If the disc contains MP3 music and
JPEG picture files, you can start a
musical slide show playback,
Select an MP3 file and press OK to start
playback, then select a picture file in the
menu and press OK to start the musical
slide show playback.
TIPS:
46
Some discs cannot be played on this recorder due to the configuration and characteristics of the disc,
or due to the condition of recording and authoring software.
Changing to another title/
chapter/track
When a disc contains more than one
track, title or chapter, you can change to a
different track, title or chapter as follows.
During playback,
Press > to go to the next title/chapter/
track.
Press . to return to the start of the
previous title/chapter/track.
OR
Press T/C repeatedly to toggle between
{ Title }, { Chapter } or { Time }. Then
use the numeric keypad 0-9 to input
the title/chapter/track number.
Searching forward/backward
You can fast forward or fast reverse a
disc at two, four, sixteen or thirty two
times the normal playback speed.
A During playback, press and hold .(fast
reverse) or > (fast forward) to switch
to the search function.
B During disc playback, press
(RIGHT)
to access the playback menu.
Use
keys to highlight { Trick
Mode - Play } and press (RIGHT) to
access the search speed options:
– FREV x32, FREV x16, FREV x4, FREV
x2, FFWD x2, FFWD x4, FFWD x16,
FFWD x32.
The sound will be muted.
C To resume normal playback, press
PLAY
.
Pausing playback and step
play
Zooming in
A During playback, press PAUSEÅto
pause playback and display a still picture.
B Press PAUSEÅagain to move one
This option allows you to enlarge the
picture on the screen and pan through
the enlarged picture.
frame forward.
C To resume normal playback, press
PLAY
.
A Press ZOOM on your remote control to
activate zoom.
B Use
keys to pan through the
zoomed picture.
C To exit, press ZOOM repeatedly until
the picture returns to the normal size.
TIPS:
The operating features described here might not be possible for certain discs.
Always refer to the instructions supplied with the discs.
47
English
Additional Playback Features
Additional Playback Features (continued)
English
Using m (INFO) options
Selecting various repeat functions
You can select various repeat play or
random play mode during playback.
This function can also be accessed via the
REPEAT key on the remote control.
A During disc playback, press m twice on
OK
the remote control.
The playback menu appears.
B Use
keys to select { Mode } and
press OK.
C Use
SELECT
keys to select one of the repeat
options.
{ Normal }
A During playback, press m twice on the
remote control.
The playback menu appears on the TV.
DVD
Mode
Trick mode
Title
Chapter
Audio
Subtitle
Angle
Title Time
Normal
Play
02/05
01/22
01/02 - OTH
Off
01/03
00:22:03 - 00:27:24
B Use
keys to select the setting you
want to adjust.
Instructions and explanation of the
options are provided in the following
pages.
C To exit, press m.
Select this to cancel the repeat mode and
return to normal playback.
{ Repeat A-B }
Select this to repeat the playback of a specific
segment within a title/chapter/track. Press OK
to mark the start and end of the segment you
want to repeat.
{ Repeat Chapter }
Select this to repeat playback of the current
chapter (DVD, recordable DVDs only.)
{ Repeat Track/Title }
Select this to repeat playback of the current
track/title.
{ Repeat Directory }
Select this to repeat playback of the current
folder/directory (MP3, JPEG, picture disc
only.)
{ Repeat Disc }
Select this to repeat playback of the entire
disc.
{ Shuffle }
Select this to randomly playback all the tracks
within the disc.
D To cancel repeat playback, press STOP ,
then press PLAY . Alternatively,
repeat steps select A to C and select
{ Normal } and press OK.
TIPS:
48
The operating features described here might not be possible for certain discs.
Always refer to the instructions supplied with the discs.
Programming disc tracks
You can play the contents of the disc in
the order you want by programming the
tracks to be played.
A Press m on the remote control.
The playback menu appears.
B Select { Mode } > { Program }.
To start program play
key to move to the right screen
and press OK.
Playback will start from the selected
track/ file/ chapter according to the
programmed sequence.
F Press
To exit program play
to exit program play.
G Press STOP
The program menu appears.
DVD
Title
Playlist
Title 1
Title 2
Title 3
Title 4
Title 5
Title 6
Title 7
Title 8
C If the disc is recorded with Titles/Folders/
Albums, press OK to access the tracks/
files/chapters.
Pressing OK at the highlighted track/file/
chapter will start playback.
Use
keys to toggle between the left
and right screen.
To program your favourite track/
file/chapter
D Use
keys to select the track/file/
chapter to program and press SELECT
on the remote control.
The selected track/file/title will appear
at the right screen.
The order on the right screen will be
the order of program playback.
Changing the audio soundtrack
language
This operation works only on DVDs with
multiple soundtrack language or VCDs
with multiple audio channels.
A Press m on the remote control.
The playback menu appears.
B Use
press
keys to select { Audio } and
to access its options.
C Use
keys to select the audio
language and press OK to confirm.
The languages may be numbered or
abbreviated, such as “En” for English.
If the language selected is not available
on the disc, the disc’s default setting for
language will be used instead.
Helpful Hint:
– Some DVDs allow soundtrack language
changes only via the DVD disc menu. To
access the disc menu, press DVD on the
remote control.
To remove the programmed item
from your selection
E Press key to move to the right screen.
Use
keys to select the track/file/
chapter to program and press SELECT
on the remote control.
TIPS:
The operating features described here might not be possible for certain discs.
Always refer to the instructions supplied with the discs.
49
English
Additional Playback Features (continued)
Additional Playback Features (continued)
English
Changing subtitle language
This operation works only on DVDs with
multiple subtitle languages, you can
change the language you want while
playing back the DVD.
A Press m on the remote control.
The playback menu appears.
B Use
keys to select { Subtitle } and
press to enter the menu and find the
different available options.
Time search
This option allows you to skip to a
specific point on the current disc.
A Press T/C on the remote control
repeatedly to display
{ Time : – : – – : – – } on the top left
corner of the screen.
Use the numeric keypad (0-9) to
enter the time required.
Playback skips to the selected time.
C Use
keys to select the language and
press OK to confirm.
The languages may be numbered or
abbreviated, such as “En” for English.
If the language selected is not available
on the disc, the disc’s default setting
language will be used instead.
Helpful Hint:
– Some DVDs discs allow subtitle language
changes only via the DVD disc menu. To
access the disc menu, press DVD.
Switching camera angles
This option is only available with DVDs
that contain sequences recorded from
different camera angles. This allows you
to view the picture from different angles.
A Press m on the remote control.
The playback menu appears.
B Use
keys to select { Angle } and
press to enter its options.
The camera angles available for
selection appears.
C Use
keys to select the camera angle
you want to switch to, then press OK to
confirm.
TIPS:
50
The operating features described here might not be possible for certain discs.
Always refer to the instructions supplied with the discs.
About HDD title edit menu
Accessing the HDD title edit
menu
In the HDD title edit menu, you can
change the title name, hide unwanted
scenes, delete titles, split a title or change
the title index picture.
OK
The edit options in the HDD title edit
menu are:
{ Play Title }
– Select a title (recording) to play.
SELECT
HDD
{ Delete Title}
( For unprotected and unlocked titles only )
– Delete the title (recording).
{ Divide Title }
– Divide the recording into two separate
titles.
{ Edit Title }
A Press HDD on the remote control.
The HDD content menu appears.
B Use
keys to highlight a title
(recording) and press .
The HDD title edit menu appears.
– Hide the unwanted scene in the
recording
HDD 16 Titles
No
001
002
003
004
005
006
007
008
{ Change Index Picture }
( For unprotected and unlocked titles only )
– Select a scene in the recording to
replace the existing index picture screen.
{ Rename }
– Change the name of a title (recording).
{ Lock/ Unlock }
– Lock or unlock a title (recording) to
prevent/allow playback.
{ Protect/ Unprotect }
– Protect or unprotect a title (recording)
to prevent/allow erasure or changes
being made.
Ch.
CH001
CH003
CH009
CH008
CH002
CH008
CH012
CH010
Date
20/05/05
14/05/05
25/04/05
30/04/05
28/03/05
12/04/05
05/08/05
30/06/05
Time
14.00
16.00
20.30
03.30
08.30
11.00
21.30
22.30
Press [OK] to play title.
Title
Travel
News
Drama
Nature
CSI
Title 3
News
Discover
Play Title
Delete Title
Divide Title
00:20:20
SP NTSC
Edit
Title
Press
[SELECT] to
mark or unmark
Change
Index Picture
recordingS.
Press [HDD] to
Rename
copy selected
recordings to DVD.
Lock
Press [SHUFFLE] to
Protect
sort by name or time.
If you have many HDD title recordings,
use .( fast reverse) or > (fast
forward) to view the previous/ next page of
HDD titles for selection.
C Use
keys to access the different
options and press OK.
Instructions and explanation of the
options are provided in the following pages.
D To exit, press
to go back to the HDD
title menu screen.
Note: Any title/ recording which has been
edited will be marked with an edited icon
next to the selected title’s index
picture.
TIPS:
Press
to go back to the previous menu.
51
English
Edit Recordings - HDD
Edit Recordings - HDD (continued)
English
Dividing a Title
You can divide the current title into two
new titles. Each of these titles is
characterized by its own index picture.
Warning! Once a title is divided, the
process cannot be reversed.
A In HDD title edit mode, use
keys to
highlight { Divide Title } and press OK.
The edit title playback screen appears.
To unhide the scenes,
D In HDD title edit mode, use
keys to
highlight { Edit Title } and press OK.
The edit title playback screen appears.
E During playback, use
keys to
navigate through the title. Press OK at
the beginning of the marked segment.
F Press
repeatedly until you reach the
end of the marked segments and press
OK.
B During playback, use
keys to
navigate through the title. Press OK to
divide the title at the desired playback
position.
A warning message will appear.
C To confirm, select
OK OK
in the menu
and press OK.
A new title will be shown in the HDD
title menu.
D To abort, select
OK
CANCEL
and press OK.
Hiding/ unhiding unwanted scenes
You can choose to hide certain scenes
from playback (e.g. skipping a commercial
scene) or make it visible again.
A In HDD title edit mode, use
keys to
highlight { Edit Title } and press OK.
The edit title playback screen appears.
B During playback, press PAUSEÅand
use . > keys to navigate through
the title. Press OK to mark the beginning
of a segment to hide.
C Press OK again to mark the end of
segment to hide.
To hide more segments, repeat steps B
to C for each segment you want to hide.
TIPS:
52
Press
to go back to the previous menu.
Helpful Hints:
– All hidden scenes will be played back in
HDD title edit mode.
– The { Edit Title } option is only available if
the title is unlocked or unprotected.
Change Index Picture
The index picture is the picture of the
title you will see when the recorder loads
up the Index menu. Normally, the first
frame of a recording is shown as the
title’s index picture.
A In HDD title edit mode, use
keys to
highlight { Change Index Picture } and
press OK.
The edit title playback screen appears.
B During playback, use
keys on the
remote control to search for the scene
to use. Press OK to confirm the current
scene as the index picture for the title.
The new index picture will be shown
in the HDD content menu.Rename a
Rename a title
The original title name is automatically
generated by the recorder. You can
change the disc name by following the
steps below.
A In HDD title edit mode, use
keys to
highlight { Rename } and press OK.
The keyboard screen appears.
B Use
keys to highlight a
character on the keyboard and press OK
to select.
The maximum input is up to 255
characters. However, only 12 characters
will be displayed at any one time in the
HDD title menu.
You can use the following keys on the
keyboard screen to edit your input:
BkSp
Space
Caps
Clear
Exit
: to remove a character to the
left of the cursor.
: to create a space between
characters.
: to toggle between upper and
lower case characters .
: to clear the entry field
completely.
: to exit the keyboard screen.
C To confirm your entry, select
OK OK
on
the keyboard and press OK.
The info panel is now updated.
To exit, select
and press OK.
TIPS:
Press
Exit
Lock/Unlock a title
You can choose to lock a title to prevent
any unauthorized playback of the
recording.
If a title has been locked, the user will be
prompted to enter a 4-digit password
preset in the system setup menu.
For details, see “Parental Rating Level.”
In HDD title edit mode, use
keys to
highlight { Lock } and press OK.
The locked title will have a Lock icon
next to its index picture.
When the title is locked, the option in
the HDD title edit menu will change to
{ Unlock }.
Protect/ Unprotect a title
You can choose to protect the title in
order to prevent accidental loss of
recordings.
In HDD title edit mode, use
keys to
highlight { Protect } and press OK.
The protected title will have a Safe
Box icon
next to its index picture.
When the title is protected, the
option in the HDD title edit menu will
change to { Unprotect }.
on the keyboard
to go back to the previous menu.
53
English
Edit Recordings - HDD (continued)
Edit Recordings - Recordable DVD
English
About disc edit menu
Accessing disc editing menu
This recorder offers various disc edit
options for various disc types. You can
change the disc content and settings of a
DVD recordable disc from the disc
editing menu. The edited contents may
not be available if you play the disc on
another DVD player.
OK
The displayed options in the disc editing
menu may differ depending on the type of
disc.
{ Play }
– Start playing from the beginning of the
disc.
{ Rename Disc }
– Change the name of the disc.
{ Erase Disc } - DVD±RWs only
– Erase all the recordings in the disc.
{ Record New Title }
– Start recording from the last empty
title in the disc.
{ Overwrite Disc } - DVD±RWs only
– Start a new recording from the
beginning of the disc, all the recorded
content will be overwritten.
REC
DVD
A Insert a recorded DVD±R/±RW disc into
the recorder. Press DVD on the remote
control.
The Index Picture screen appears on
the TV.
B Select the first title on the disc, press and
hold
on the remote control.
The disc editing menu appears. Press
to access the options. The available
editing options may vary for DVD±R and
DVD±RW discs.
{ Finalize Disc } - DVD±Rs only
– Finalize the disc to enable playback on
other DVD players. Further recording
and editing to the disc are not allowed. It
is not possible to unfinalize the disc.
Play
PAL
DVD
Rename Disc
Erase Disc
Record New Title
Overwrite disc
{ Make Compatible } - DVD±RWs only
– To ensure the edited changes remain
when the disc is played back on another
DVD player. (eg., hidden chapters to
remain hidden).
C Use
{ Lock/Unlock Disc } - DVD±RWs only
– Lock or unlock a disc to prevent
accidental erasure or changes being
made.
D To exit, press DVD to go back to the
EDIT
Finalize Disc
Make Compatible
Lock Disc
keys to access different options
and OK to select.
Instructions and explanation of the
options are provided in the following pages.
disc Index Picture screen.
TIPS:
54
No further recording and editing can be carried out on a finalized recordable DVD.
Press DVD to return to the index picture screen.
Rename disc
The original disc name is generated
automatically by the recorder. You
can change the disc name by following
the steps below.
A In disc editing menu, use
keys to
select { Rename Disc } and press OK.
The keyboard screen appears.
B Use
keys to highlight a
character on the keyboard and press OK
to select.
The maximum input is up to 9
characters.
You can use the following keys on the
keyboard screen to edit your input:
BkSp
Space
Caps
Clear
Exit
: to remove a character to the
left of the cursor.
: to create a space between
characters.
: to toggle between upper and
lower case characters .
: to clear the entry field
completely.
: to exit the keyboard screen.
C To confirm your entry, select
OK OK
on
the keyboard and press OK.
The info panel is now updated.
To exit, select
and press OK.
Exit
on the keyboard
Erase disc (DVD±RWs only)
This erases the content of the
DVD±RW disc including those that was
not recorded on this recorder. Once
the existing content is erased, it can be
used for recording.
A In disc editing menu, use
keys to
select { Erase Disc } and press OK.
A warning message will appear.
B Select
YESOK
or NO OK
confirm.
in the menu to proceed
, to abort, then press OK to
Helpful Hint:
– To erase content that cannot be played
back on this recorder, please use the option
{ Delete Optical Disc } under the setup
menu.
Record a new title
This function allows you to start a new
recording at the remaining empty space
in the DVD recordable disc.
A In disc editing menu, use
keys to
select { Record New Title } and press
OK.
B Select the source you want to record
from and press REC
recording.
to start
Overwrite disc (DVD±RWs only)
This function allows you to start a new
recording from the beginning of a
DVD±RW regardless of the contents of
the disc.
A In disc editing menu, use
keys to
select { Overwrite disc } and press OK.
B Select the source you want to record
from and press REC
recording.
TIPS:
to start
No further recording and editing can be carried out on a finalized recordable DVD.
Press DVD to return to the index picture screen.
55
English
Edit Recordings - Recordable DVD (continued)
Edit Recordings - Recordable DVD (continued)
English
Make compatible (DVD±RW only)
The edited DVD±RW may still display
the original titles or hidden scenes when
playbacked on other DVD players. This
function ensures that the edited changes
of the DVD±RW remain when played
back on other players.
In disc editing menu, use
keys to
select { Make Compatible } and press
OK to confirm.
Helpful Hint:
– If the option {Compatible} is not available
for selection, it means that the disc is already
compatible.
Playing your recordings
(DVD±R) on other DVD
players
It is necessary to finalize a DVD±R disc
before you can play it on any other DVD
player. Otherwise, the disc will only
playback on this recorder.
After a DVD±R disc has been
finalized, no further recordings or
editing can be made to it. Make
sure you have completed all the
recordings and editing before
finalizing the disc.
A In disc editing menu, use
Lock/Unlock disc (DVD±RWs only)
You can choose to protect the
recordings on the DVD±RW disc in
order to prevent accidental loss of
recordings.
A In disc editing menu, use
keys to
select { Lock Disc } and press OK.
The disc is locked for this DVD
recorder only.
When the disc is locked, the option in
the disc editing menu will change to
{ Unlock Disc }.
keys to
select { Finalize Disc } and press OK.
A warning message will appear.
B Select
YESOK
in the menu and press
OK to start the process.
Finalization will take a few minutes.
Do not try to open the disc tray or turn
the power off as this may render the disc
unusable.
C Select
NO OK
B If you want to overwrite or edit on the
protected disc, select { Unlock Disc }.
TIPS:
56
No further recording and editing can be carried out on a finalized DVD±R.
Press DVD to return to the index picture screen.
to abort.
About DVD title editing
You can change the individual title
information or delete a title (recording)
on a recorded DVD disc. If the
recordable DVD disc has been finalized,
it cannot be edited.
The displayed options in the title editing
menu may differ depending on the type of
disc.
{ Play Title }
– Start playing a recording.
{ Edit Title }
– Access video editing menu.
English
Edit Recordings - Recordable DVD (continued)
Accessing DVD title edit
menu
A Insert a recorded DVD±R/±RW disc into
the recorder. Press DVD on the remote
control.
The Index Picture screen appears on
the TV.
During playback, press DVD to access
the Index Picture screen.
B Use
keys to highlight a title
(recording), and press .
The title editing menu appears.
Play Title
{ Rename Title }
– Change the name of the recording.
Edit Title
Rename Title
Erase Title
{ Erase Title } - DVD±RWs only
– Delete the title (recording.)
Overwrite Title
Overwrite Disc
{ Overwrite Title } - DVD±RWs only
– Start a new recording and the existing
title (recording) will be overwritten.
{ Overwrite Disc } - DVD±RWs only
– Overwrite from existing selected title
onwards to the end of the disc.
{ Append Title }
– Insert a new recording to the last
existing recording.
Append Title
3. My movie
11 / 04 / 2004
12 : 31 : 53
HQ 00 : 05 : 59
Empty
C Use
keys to access different options
and OK to select.
Instructions and explanation of the
options are provided in the following
pages.
D To exit, press
.
Editing video
This feature allows access to the video
editing menu. See “About video editing”
on pages 59~61 for more information.
In title editing menu, use
keys to
select { Edit Title } and press OK.
The video editing menu appears.
The recorder will play the
selected title.
TIPS:
No further recording and editing can be carried out on a finalized DVD±R.
Press to go back to the previous menu.
57
Edit Recordings - Recordable DVD (continued)
English
Rename title
The original title name is generated
automatically by the recorder. You can
give a new name to the title by following
the steps below.
A In title editing menu, use
keys to
select { Rename Title } and press OK.
The keyboard screen appears.
B Use
You can use the following keys on the
keyboard screen to edit your input:
: to remove a character to the
left of the cursor.
: to create a space between
characters.
: to toggle between upper and
lower case characters .
: to clear the entry field
completely.
: to exit the keyboard screen.
Space
Caps
Clear
Exit
C To confirm your entry, select
OK OK
on
the keyboard and press OK.
The info panel is now updated.
To exit, select
and press OK.
Exit
on the keyboard
Erase title
You can delete a specific title (recording)
from the disc. However, for the DVD±R
disc, the deleted space cannot be used for
further recording.
A In title editing menu, use
keys to
select { Erase Title } and press OK.
A warning message will appear.
B Select
YESOK
or NO OK
confirm.
TIPS:
58
A In title editing menu, use
keys to
select { Overwrite Title } and press
OK.
B Select the source you want to record
from and press REC
recording.
keys to highlight a
character and press OK to select.
The maximum input is up to 9
characters.
BkSp
Overwrite title (DVD±RW only)
This function allows you to record a new
title from the beginning of the current
title in the DVD±RW disc.
to start
Overwrite from the selected title
You can select to overwrite only the
recordings from the selected title to the
end of the disc.
A In title editing menu, use
keys to
select { Overwrite Disc } and press OK
to delete.
Append recording
This function allows you to append
recording to the last existing title.
Note: Under the { Append Title }
option, it is not possible to select the
mode of record quality when a recording
is appended to an existing title on a DVD.
The recording quality will always be
determined by the quality mode of the
existing title.
A In title editing menu, use
keys to
select { Append Title } and press OK.
B Press SOURCE to select the input
channel to append.
C Press REC
to start append recording.
D To stop append recording, press
STOP
.
in the menu to proceed
to abort, then press OK to
No further recording and editing can be carried out on a finalized DVD±R.
Press to go back to the previous menu.
About video editing
Accessing video editing menu
After a recording has been made, this
recorder allows you to edit the video
content. You can add/delete chapter
marker, hide unwanted scenes, change
the picture in the index picture screen
and split a title (recording) into two.
OK
When you playback a recording in video
edit mode, the entire recording will be
played back including hidden scenes.
The edit functions available in the disc
editing menu are:
{ Title }
– Select a specific title (recording) to
play.
{ Chapter }
– Select a chapter within the selected
title.
{ Chapter Marker }
– Insert a chapter marker in the
recording or erase a chapter marker to
combine two chapters.
{ Hide Chapter }
– Hide the unwanted scene in the
recording.
PLAY
SELECT
DVD
A Insert a recorded DVD±R/±RW disc into
the recorder. Press DVD on the remote
control.
The Index Picture screen appears on
the TV.
B Use
keys to highlight a title
(recording), and press to access the
menu.
The title editing menu appears.
C Use
keys to select { Edit Title }
and press OK.
The edit mode menu appears.
Edit Mode
Title 02/06
{ Index Picture }
– Select a scene in the recording as the
index picture screen.
Chapter 01/10
Play
Chapter Marker
Hide Chapter
{ Split Title } - DVD±RWs only
– Divide the recording into two under
separate titles.
Index Picture
Split Title
Title Elapsed 0:20:45
D Use
keys to access different options
and press OK to select.
Instructions and explanation of the
options are provided in the following
pages.
E To exit, press DVD.
TIPS:
No further recording and editing can be carried out on a finalized DVD±R.
Press to go back to the previous menu.
59
English
Edit Recordings - Recordable DVD (continued)
Edit Recordings - Recordable DVD (continued)
English
Selecting a title
It shows the current title and the total
number of titles in the disc. It also allows
you to select another title.
A In edit mode, use
keys to select
{ Title } and press OK.
Creating chapter markers
You can create a chapter by inserting
chapter marker at any point within a title
during playback. This will allow you to
access a specific point in the recording
easily or set a chapter you wish to hide.
Title
B Use the numeric keypad 0-9 to key in
a title and press OK.
The recorder will play the selected
title.
Chapter Chapter Chapter Chapter
chapter markers
Selecting a chapter
It shows the current chapter and the
total number of chapters in the title. It
also allows you to select another chapter
within the title.
A In edit mode, use
keys to select
{ Chapter } and press OK.
B Use the numeric keypad 0-9 to key in
the chapter and press OK.
The recorder will play the
selected chapter.
A In edit mode, use
keys to select
{ Chapter Marker } and press
OK.
B Use
keys to select one of the
options and press OK to confirm.
{ Insert Marker }
Select this to insert a new chapter
marker at the current point of playback.
{ Delete Marker }
Select this to delete the current chapter
marker (it refers to the closest marker
before the current point of playback.)
The current chapter will then combine
with the chapter before it.
{ Delete All Markers }
Select this to delete all the chapter
markers in the current title.
TIPS:
60
No further recording and editing can be carried out on a finalized DVD±R.
Press to go back to the previous menu.
Hiding an unwanted chapter
You can choose to hide certain scenes
from playback (e.g. skipping a commercial
scene) or make it visible again.
A Create a chapter marker at the scene
you are going to hide. ( See previous page
on “Creating chapter markers”.)
B Select the chapter you want to hide and
start playback. ( See previous page on
“Selecting a chapter”.)
C In edit mode, use
keys to select
{ Hide Chapter } and press OK.
The current chapter will be hidden.
To unhide a chapter
keys to select
{ Unhide Chapter } and press
OK.
The video editing menu appears.
While in editing mode, the hidden
chapter/chapters will play.
Changing Index Picture
The index picture is the picture of the
title you will see when the recorder loads
up the Index menu. Normally, the first
frame of a recording is shown as the
title’s index picture.
A In edit mode, use
keys to select
{ Index Picture } and press OK.
The display will be in playback mode.
B Use
keys on the remote control to
search for the scene to use, then press
OK to confirm the current scene as the
index picture for the title.
The new index picture will be shown
in the title menu.
A In edit mode, use
B Wait for the chapter you want to unhide
to occur or use
keys on the remote
control to make a fast search.
The current chapter will be visible
during playback.
Helpful Hint:
– All the hidden chapters will be played
back while in video editing mode.
TIPS:
Splitting a title (DVD±RWs only)
You can divide the current title into two
new titles. Each of these titles will be
characterized by its own index picture.
Warning! Once a title is divided, the
process cannot be reversed.
In edit mode, use
keys to select
{ Split Title } and press OK to
divide the title at the current playback
position.
A new title will be shown at the Index
Picture screen.
No further recording and editing can be carried out on a finalized DVD±R.
Press to go back to the previous menu.
61
English
Edit Recordings - Recordable DVD (continued)
Setup Menu Options
English
Accessing the Setup Menu
The setup menu provides various options
for you to adjust the recorder to suit
your preferences.
SETUP MENU - VIDEO
TV System
PAL
TV Shape
4:3 LB
Progressive Scan
Off
Page 63
DivX(R) Video on Demand OK
SETUP MENU - AUDIO
SPDIF Output
RAW
LPCM Output
LPCM 96Hz
Page 65
OK
SETUP
SETUP MENU - LANGUAGE
A Press SETUP on the remote control.
The setup menu appears on TV.
B Use
and press
System Language
English
Audio Language
English
Subtitle Language
Off
Disc Menu Language
English
Page 25
keys to highlight a setup option
to access.
C Use
keys to highlight the setting you
wish to change and press OK to confirm
and go back to the previous menu item.
Instructions and explanation of the
options are provided in the following
pages.
D To exit, press SETUP.
SETUP MENU - DATE / TIME
Date(dd/mm/yyyy)
31 12 2005
Time(hh:mm)
15 : 33
Page 25
SETUP MENU - PREFERENCES
SETUP MENU - GENERAL
Auto Chapter Marker
5min.
Record Quality
SP
Auto Program
Search
Manual Program
Edit
Sort
OK
Pages
22-23,
31
Parental Level
Off
Change Password
OK
Reset Menu Settings
OK
Screensaver
On
Page 64
SETUP MENU - HDD
62
Save Time Shift Buffer
No
HDD Info
Show
Space Management
Automatic
Delete HDD
OK
Delete Optical Disc
OK
Page 29
VIDEO settings (underlined options are the factory default settings)
TV System
The colour system of the DVD system, DVD and TV should match.
Only then will it be possible to play a DVD on this system. Before
changing the TV system, determine the colour system of your TV.
Press to access this menu and use
the options.
TV Shape
keys to select one of
{ NTSC }
– Select this if the connected TV has the NTSC colour
system. It will change the video signal of a PAL disc and
output it to NTSC format.
{ PAL }
– Select this if the connected TV has the PAL colour
system. It will change the video signal of an NTSC disc
and output it to PAL format.
The picture shape can be adjusted to fit your TV.
Press to access this menu and use
the options.
keys to select one of
{ 4:3 LB } –
For a ‘wide screen’ display with black bars on
the top and bottom of the screen.
{ 4:3 PS } –
For a full-height picture with sides trimmed.
{ 16:9 WS } – For wide screen TV (frame ratio 16:9.)
Progressive Scan
Progressive scan delivers a higher picture quality than the standard
interlaced TV channel scan. It only works when you have connected the
recorder’s Y Pb Pr jacks to your TV that supports the progressive video
input. Otherwise, the image may not appear or will be distorted. Please
check your TV user manual for more information.
Press to access this menu and use
options.
keys to select one of the
{ Off } – Select this to disable progressive scan feature.
{ On } – Select this to enable progressive scan feature.
If a blank/distorted TV screen appears, wait for 10 seconds for the auto recovery.
DivX® Video on
Demand
Philips provides you with the DivX® VOD (Video On Demand)
registration code that allows you to rent and purchase videos
using the DivX® VOD service. For more information, visit us at
www.divx.com/vod.
1) Press to display the registration code.
2) Use the registration code to purchase or rent videos from DivX®
VOD service at www.divx.com/vod. Follow the instructions and
copy the video from your computer onto a CD-R/RW for playback
on this recorder.
63
English
Setup Menu Options (continued)
Setup Menu Options (continued)
English
PREFERENCES settings (underlined options are the factory default settings)
Parental Level
Some DVDs may have a parental level assigned to the complete
disc or to certain scenes on the disc. This feature lets you set a
playback limitation level.
The rating levels range from 1 to 8 and are country dependent.
You can prohibit the playing of certain discs that are not
suitable for your children, or have certain discs played with
alternative scenes.
Press to access this menu and use
the options.
Rating explanations
keys to select one of
{ 1. Kid Safe } ~ { 2. G } – Childsafe; acceptable for viewers of all
ages.
{ 3. PG }
– Parental Guidance suggested.
{ 4. PG13 } – Unsuitable for children under age 13.
{ 5. PG R } ~ { 6. R } – Restricted; recommended that parents
restrict children under 17 from viewing or allow to
view only when supervized by a parent or adult
guardian.
{ 7. NC 17 } – No children under age 17; not recommended viewing
for children under age 17.
{ 8. Adult } – Mature material; should be viewed only by adults due
to graphic sexual material, violence or language.
{ Off }
– Parental Control is not active.
DVDs that are rated higher than the level you have selected will not
play unless you enter your four-digit pin code.
Change Password
New Password
Enter password
****
Enter new password
****
Re-enter password
OK
OK
CANCEL
This option allows you to change your password setting for
parental control.
1) Use
keys to highlight { Change Password } and press OK.
You will be prompted to enter your four-digit pin code.
2) Use the numeric keypad 0-9 to enter your four-digit pin code.
When doing this for the first time, enter the default password
‘3308’.
If you forget your four-digit pin code, the default password is 3308.
3) Enter your new password and press
.
4) Re-enter your new password and select
the remote control to confirm.
64
OK OK
, then press OK on
English
Setup Menu Options (continued)
PREFERENCES settings (underlined options are the factory default settings)
Reset Menu
Settings
Screensaver
Press
to reset the menu settings of this recorder.
A warning message will appear. Select OK OK
in the menu to
OK
proceed or CANCEL
to abort, then press OK to confirm.
The screen saver prevents damage to the TV screen by
avoiding exposure to a static image for too long.
Press to access this menu and use
the options.
keys to select one of
{ On }
– Select this if you wish to turn off the TV screen, after
playback had been stopped or paused for more than
15 minutes.
{ Off }
– Select this to disable the screen saver.
AUDIO settings (underlined options are the factory default settings)
SPDIF Output
LPCM Output
Press to access this menu and use
the options.
keys to select one of
{ RAW }
– Select this if you have used the recorder’s COAXIAL
OUT jack to connect to a multichannel receiver.
{ LPCM }
– Select this if you have used the recorder’s COAXIAL
OUT jack to connect to a stereo or audio/video
system.
This setting allows you to select between two levels:
{ LPCM 48 kHz} – Select this if the connected audio device is
capable of processing digital signal input with
sampling rates of 48 kHz. In addition, the disc
you are playing back must be recorded in 48kHz
LPCM format.
{ LPCM 96 kHz} – Select this if the connected audio device is
capable of processing digital signal input with
sampling rates of 96 kHz.In addition, the disc
you are playing back must be recorded in 96kHz
LPCM format.
65
Firmware Upgrade
English
Installing the latest firmware
Periodically, Philips will issue upgrades for
the firmware that was initially installed in
your recorder as the firmware is
continuously refined for greater stability
and compatibility of the recorder.
Caution! Power supply must not be
interrupted during upgrade!
Visit Philips’ website at
‘www.philips.com/support’ to check for
the availability of the latest firmware
upgrade.
Note: When checking for the latest
firmware upgrade, please also check for
any accompanying instructions on
installing the firmware.
66
Troubleshooting
English
WARNING
Under no circumstances should you try to repair the system yourself, as this will
invalidate the warranty. Do not open the system as there is a risk of electric shock.
If a fault occurs, first check the points listed below before taking the system for repair.
If you are unable to remedy a problem by following these hints, consult your dealer or
Philips for help.
Problem
Solution
No power.
– Press STANDBY-ON button on the front of the recorder to
turn on the system.
– Make sure the AC outlet has power.
The recorder does not
respond.
– There is a technical problem. Disconnect the recorder from the
power outlet for 30 seconds, then reconnect and switch on the
recorder again.
Remote control does not
work.
– Aim the remote control directly at the iR sensor on the front of
the recorder (not towards TV).
– Remove any obstacles between the recorder and remote
control.
– Batteries are weak, replace the batteries.
No picture.
– Turn on your TV and set to the correct Video In channel for
the recorder. You may go to Channel 1 on your TV, then press
the channel down button on your TV’s remote control until you
see the TV program.
– Check the video connection between the recorder and the TV.
– Your recorder might have been set to Progressive Scan mode
while your TV does not support Progressive Scan.
Follow the steps below:
1) Connect the supplied AV cable (red/white/yellow) from your
recorder OUT2 on the rear panel to the TV’s Video In and
Audio In jacks.
2) Turn on the TV and use the TV’s remote control to select
the corresponding video-in channel on the TV. (eg., AV, EXT1.)
3) Turn on the recorder and wait till the display panel shows a
channel number. Press SETUP on the remote control once. The
message ‘MENU’ will be shown on the display panel. Enter the
code “1168” and wait for the screen to be refreshed after a few
seconds. The “PRO SCAN” icon on the display panel will
disappear.
No sound.
– Check the recorder audio connections. Read chapter “Basic
Recorder Connections - Connecting the audio cables” for
details.
– Set the option for Digital audio output correctly, based on the
device you have connected to the recorder. Read chapter
“Setup Menu Options - AUDIO settings” for details.
No TV signal received from
the recorder.
– Have your antenna or cable TV signal checked.
– Install the TV channel. Read chapter “Installation and Setup Setting your TV channel programs” for details.
67
Troubleshooting (continued)
English
Problem
Solution
Disc will not play.
– Insert the disc with the label facing up.
– Wrong region code. The DVD must be coded for ALL regions
or Region 3 or 4 in order to play on this recorder.
– There is no recording on the disc or it is not a supported type
of disc. Read chapter “Playback from Disc - Playable discs” for
details.
– Make sure the disc is not scratched or warped. Clean the disc
or replace a new one.
– Check if the disc is defective by trying another disc.
The picture is distorted or
black and white during
playback.
– The disc does not match with the TV colour system standard
(PAL/NTSC).
– The disc is dirty, clean the disc.
– Sometimes a small amount of picture distortion may appear.
This is not a malfunction.
There is picture or sound
interference with the TV
reception.
– Have your antenna or cable TV signal checked.
– Fine-tune your TV channel. Read chapter “Installation and Setup
- Setting your TV channel programs” for details.
Distorted sound coming from
a connected hi-fi system or
amplifier.
– Do not connect any cables from the recorder to the ‘Phono’
input of your amplifier.
– If you are playing a DTS CD, you have to connect the COAXIAL
jack of this recorder to a Hi-Fi system or amplifier.
Recordings are not occurring
as scheduled. New recordings
cannot be made.
– The TV channel you want to record is not stored. Or, you may
have selected the wrong program number. Check the TV
channels stored.
– You have to reset the timer recording after adjusting the clock
setting.
– You cannot use the recorder to duplicate copy-protected
materials (DVDs or videotapes) onto a DVD recordable disc.
– The hard disk could be full. Delete some titles to create space
for new recordings.
The wrong TV channel was
decoded (recorded) after you
programmed a recording
using the G-CODE® system.
1) Enter the G-CODE® programming number of the desired TV
channel.
2) Press OK to confirm.
3) Check the channel number in the {Program #} input field. If this
does not correspond to the desired TV channel, select this
entry field and change the channel number.
4) Press OK to confirm.
The recorded DVD cannot
be played back on another
DVD player.
68
– If a recording is too short, it is possible that a DVD player/
recorder cannot detect it. Please observe the following
‘minimum recording times’. Mode of record quality: {High
Quality - HQ} – 5 minutes, {Standard Play - SP} – 10 minutes,
{Standard Play Plus - SP+} – 13 minutes, {Long Play - LP} – 15
minutes, {Extended Play - EP} – 20 minutes, {Super Long Play SLP} – 30 minutes.
– You have to finalize the DVD±R. Refer to chapter “Playing your
recordings on other DVD players” for details.
Problem
Solution
The message ‘UNKNOWN
DISC’ appears.
– This message may appear if you insert a disc that may have
encountered one of the following:
– Error during recording: The title may be missing.
– Error while changing the title/index picture: The original title/
index picture may be visible.
– Error while finalizing or the disc has not been finalized.
Picture is fuzzy and
brightness varies when
copying DVD Video discs or
prerecorded video cassettes.
– This happens if you try to copy DVDs or video cassettes that
have been copy-protected. Even though the picture on the TV is
fine, but the recording on the DVD recordable disc is faulty.
This interference is unavoidable with copy-protected DVDs or
video cassettes.
– The DVD recordable disc has a limited recording lifetime, please
change a new disc for recording.
The message ‘This will clear
the time shift buffer’ appears.
– The requested action requires that the time shift buffer
(temporary HDD storage) to be cleared. All contents that were
not marked for recording will be deleted.
There is a power failure
during the formatting of the
recorder’s HDD.
– You have to reselect the { Delete HDD } option and delete the
HDD contents again.
There is a power failure
during the copying of files to
a DVD±R disc.
– The titles that were previously recorded will be deleted and the
space used for recording cannot be re-used. The disc can be
used as a normal blank disc. You have to re-copy the files to the
disc again.
During recording from the
time shift buffer, it is not
possible to start or stop a
recording.
– Parts of the signal may be copy-protected by the
broadcaster. This portion of the time shift video bar will be
shown in a different color. You can only start or stop a
recording if the selected portion does not contain any
copyright content.
keys or .> keys to navigate to a
– Use
non-protected portion and press REC to start a recording.
To end a recording, press STOP.
– Press SELECT to clear a recording at any time.
69
English
Troubleshooting (continued)
Specifications
English
Video Recording
Tuner/Reception/ Transmission
• Recording System: PAL / NTSC
• Compression formats: MPEG2
• Modes of Record Quality:
High Quality
: HQ
(M1)
Standard Play
: SP
(M2)
Standard Play Plus
: SP+
(M2x)
Long Play
: LP
(M3)
Extended Play
: EP
(M4)
Super Long Play
: SLP
(M6)
• Recording enhancements:
Auto Chapter Marker Insertion, Divide Title,
Erase, Manual Chapter Marking, One Touch
Record
• Audio compression: Dolby Digital
• TV System: PAL, NTSC
• Aerial input: 75 ohm coaxial (IEC75)
Video Playback
• Disc Playback Media: CD, CD-R/CD-RW, DVD,
DVD-Video, DVD+R, DVD+RW, DVD-R,
DVD-RW, MP3-CD, Video CD, SVCD
• Compression formats: MPEG2, MPEG1, MPEG4,
DivX
• Video disc playback system: PAL, NTSC
Audio Playback
• Disc Playback Media: MP3-CD, CD, CD-R/
CD-RW
• Compression formats: Dolby Digital, DTS, MP3,
PCM,
• MP3 bit rates: 32 - 256 kbps
Still Picture Playback
• Disc Playback Media: Picture CD
• Picture compression format: JPEG
• Picture enhancement: Rotate, Zoom, Slideshow
TV systems
• Playback:
• Recording:
• Internal tuner:
PAL/NTSC
PAL/NTSC
PAL/NTSC
Storage Media
• Recording :
– DVD+R, DVD+RW, DVD-R, DVD-RW,
• Hard Disk Capacity:
– DVDR 3360H : 160GB
– DVDR 3370H : 250GB
• HDD recording enhancements:
– Instant Replay, Time Shift Buffer
• Extra Hard Disk Technology:
– Pause Live TV, Simultaneous Record and
Playback, Direct Record to DVD
• HDD to DVD archiving: high speed (direct copy)
Connectivity
• Rear Connections
–
–
–
–
–
–
–
S-video out
Component Video out
Video (CVBS) out
Analog audio left/right out
Antenna in
TV out
Digital audio out (coaxial)
• Front Connections
– i.LINK DV in (IEEE 1394 4-pin)
– S-Video in
– Video (CVBS) in
– Analog audio left/right in
Timer Recording
• Programmable events: 20
• Repeat modes: Once, Daily, Weekly
• Enhancement: Manual Timer, G-CODE®
Convenience
• Direct Record to optical disc
• Child Protection: Parental Control
Video Performance
• D/A Converter
10 bit, 54 MHz
• A/D Converter
10 bit, 27 MHz
• Picture Enhancement: Progressive Scan
Power
• Power Supply:
110V~240V, 50~60 Hz
• Power Consumption:
28 W
• Standby power consumption: < 3.0 W
Audio Performance
•
•
•
•
•
DA Converter
24 bit, 192 kHz
AD Converter
24 bit, 96 kHz
Signal / Noise (1kHz) 100 dB
Dynamic range (1kHz) 95 dB
Crosstalk (1kHz)
105 dB
70
Dimensions
• Set dimension (W x H x D) : 435 x 65 x 340 mm
• Set Weight : 4.3 kg
Analog: Sound that has not been turned into
numbers. Analog sound varies, while digital sound
has specific numerical values. These jacks send audio
through two channels, the left and right.
Aspect ratio: The ratio of vertical and
horizontal sizes of a displayed image. The horizontal vs. vertical ratio of conventional TVs. is 4:3,
and that of wide-screens is 16:9.
AUDIO OUT Jacks: Red and white jacks
on the back of the system that send audio to
another system (TV, Stereo, etc.)
Chapter: Sections of a picture or a music piece
on a DVD that are smaller than titles. A title is
composed of several chapters. Each chapter is
assigned a chapter number enabling you to locate
the chapter you want.
Component Video Out Jacks: Jacks on
the back of the DVD System that send high-quality
video to a TV that has Component Video In
jacks (R/G/B,Y/Pb/Pr, etc.)
Digital: Sound that has been converted into
numerical values. Digital sound is available when
you use the DIGITAL AUDIO OUT COAXIAL.
These jacks send audio through multiple channels,
instead of just two channels as analog does.
Disc menu: A screen display prepared for
allowing selection of images, sounds, subtitles,
multi-angles, etc recorded on a DVD.
DivX 3.11/4.x/5.x: The DivX code is a
patent-pending, MPEG-4 based video compression
technology, developed by DivXNetworks Inc., that
can shrink digital video to sizes small enough to be
transported over the internet, while maintaining
high visual quality.
Dolby Digital: A surround sound system developed by Dolby Laboratories containing up to six
channels of digital audio (front left and right,
surround left and right, center and subwoofer.)
DTS: Digital Theatre Systems.This is a surround
sound system, but it is different from Dolby Digital.
The formats were developed by different companies.
Index Picture Screen: A screen that gives an
overview of a DVD±RW or DVD±R. An Index
Picture represents each recording.
JPEG: A very common digital still picture format.
A still-picture data compression system proposed
by the Joint Photographic Expert Group, which
features small decrease in image quality in spite of
its high compression ratio.
MP3: A file format with a sound data compression
system. “MP3” is the abbreviation of Motion
Picture Experts Group 1 (or MPEG-1) Audio
Layer 3. By using the MP3 format, one CD-R or
CD-RW can contain about 10 times more data
then a regular CD.
MPEG: Motion Picture Experts Group. A
collection of compression systems for digital audio
and video.
Multichannel: DVDs are formatted to have each
sound track constitute one sound field.
Multichannel refers to a structure of sound tracks
having three or more channels.
PBC: Playback Control. Refers to the signal
recorded on video CDs or SVCDs for controlling
playback. By using menu screens recorded on a
Video CD or SVCD that supports PBC, you can
enjoy interactive playback and searching.
PCM: Pulse Code Modulation. A digital audio
encoding system.
Parental control: Limits disc play according to
the age of the users or the limitation level in each
country. The limitation varies from disc to disc;
when it is activated, playback will be prohibited if
the software’s level is higher than the user-set
level.
Region code: A system allowing discs to be
played only in the region designated. This unit will
only play discs that have compatible region codes.
You can find the region code of your unit by
looking on the product label. Some discs are
compatible with more than one region (or ALL
regions.)
S-Video: Produces a clear picture by sending
separate signals for the luminance and the color.
You can use S-Video only if your TV has an S-Video
In jack.
Surround: A system for creating realistic three
dimensional sound fields full of realism by
arranging multiple speakers around the listener.
Title: The longest section of a movie or music
feature on DVD. Each title is assigned a title
number, enabling you to locate the title you want.
VIDEO OUT jack:Yellow jack on the back
of the DVD system that sends the DVD picture
video to a TV.
71
English
Glossary
Display panel symbols/ messages
English
The following symbols/messages may
appear on your recorder display:
00:00
Multifunction display/ text line
– Title/track number
– Total/elapsed/remaining title/track time
– Disc/title name
– Additional information regarding the disc
– TV channel number or source of video
– Clock (This is displayed in Standby mode).
– TV program title
X TIMER
A timer recording has been programmed
or is active.
BLANK
No recordings on the disc.
CLOSING
Disc tray is closing.
EMPTY
No recordings in the hard disk drive.
UPDATE
Please wait until the blinking message
disappears. The disc is being formatted or
data is being written to it.
MENU
The system setup menu, disc menu or
title menu display is on.
HDDMENU
The hard disk menu display is on.
NO DISC
No disc has been inserted. If a disc has
been inserted, then it is possible that the
disc cannot be read.
OPEN
Disc tray is opened or opening.
72
PRO SCAN
Lights up when progressive scan is
activated.
READING
Disc is being recognized by the recorder.
PHILIPS
The recorder has been turned on.
SCANXXX
Please wait until this message disappears.
The recorder is busy processing an
operation. XXX indicates the number of
found channels, and is constantly updated
¡_CHXXX
In time shift mode, where XXX indicates
the input video source or channel
number of tuner input.
73
TV System Guide
English
COUNTRY
VHF
AFGHANISTAN
ALBANIA
ALGERIA
ANGOLA
ARGENTINA
AUSTRALIA
AUSTRIA
AZORES
BAHAMAS
BAHRAIN
BANGLADESH
BARBADOS
BELGIUM
BERMUDA
BOLIVIA
BOTSWANA
BRAZIL
BRUNEI
BULGARIA
BURKINA FASO
BURMA
BURUNDI
CAMBODIA
CAMEROON
CANADA
CANARY ISLANDS
CHAD
CHILE
CHINA
COLOMBIA
COSTA RICA
CROATIA
CUBA
CYPRUS
CZECH REPUBLIC
DAHOMEY
DENMARK
DJIBOUTI
DOMINICAN REP
ECUADOR
EGYPT
EL SALVADOR
EQUAT. GUINEA
ESTONIA
ETHIOPIA
FIJI
FINLAND
FRANCE
FRENCH POLYNESIA
GABON
GAMBIA
GERMANY
GHANA
GIBRALTAR
GREECE
GREENLAND
GUADELOUPE
GUAM
GUATEMALA
GUINEA
GUYANA (FRENCH)
HONDURAS
PAL/SECAM B
PAL B
PAL B
PAL I
PAL N
PAL B
PAL B
PAL B
NTSC M
PAL B
PAL B
NTSC M
PAL B
NTSC M
NTSC M
PAL I
PAL M
PAL B
SECAM D
SECAM K1
NTSC M
SECAM K1
NTSC M
PAL B
NTSC M
PAL B
SECAM K1
NTSC M
PAL D
NTSC M
NTSC M
PAL B
NTSC M
PAL B
PAL D
SECAM K1
PAL B
SECAM B
NTSC M
NTSC M
SECAM B/PAL B
NTSC M
PAL B
PAL B (was SECAM)
PAL B
PAL B
PAL B
SECAM L
SECAM K1
SECAM K1
PAL I
PAL B
PAL B
PAL B
PAL B (was SECAM)
NTSC/PAL B
SECAM K1
NTSC M
NTSC M
PAL K
SECAM K1
NTSC M
74
UHF
PAL G
PAL G
PAL N
PAL H
PAL G
PAL G
PAL H
NTSC M
PAL M
PAL B
SECAM K
PAL G
NTSC M
NTSC M
NTSC M
NTSC M
PAL G
NTSC M
PAL G
PAL K
PAL G
SECAM G
NTSC M
NTSC M
SECAM G/PAL G
NTSC M
DVD REGIONS
5
2
5
5
4
4
2
4
2
5
4
2
4
5
4
2
5
5
3
5
1
2
5
4
6
4
4
2
4
2
PAL D
PAL G
2
5
4
4
2
4
5
5
5
PAL G
SECAM L
2
2
PAL G
PAL G
PAL H
PAL G
NTSC M
NTSC M
5
5
2
5
2
2
2
1
4
5
4
4
COUNTRY
VHF
UHF
DVD REGIONS
LIBYA
LITHUANIA
LUXEMBOURG
MADAGASCAR
MADEIRA
MALAGASY
MALAWI
MALAYSIA
MALI
MALTA
MARTINIQUE
MAURITANIA
MAURITIUS
MEXICO
MONACO
MONGOLIA
MOROCCO
MOZAMBIQUE
NAMIBIA
NEPAL
NETHERLANDS
NETH. ANTILLES
NEW CALEDONIA
NEW GUINEA
NEW ZEALAND
NICARAGUA
NIGER
NIGERIA
NORWAY
OMAN
PAKISTAN
PANAMA
PARAGUAY
PERU
PHILIPPINES
POLAND
PORTUGAL
PUERTO RICO
QATAR
REUNION
RUMANIA
RUSSIA
RWANDA
SABAH/SAWARA
ST. KITTS
SAMOA (US)
SAUDI ARABIA
SENEGAL
SEYCHELLES
SIERRA LEONE
SINGAPORE
SLOVAK REPUBLIC
SOMALIA
SOUTH AFRICA
SPAIN
SRI LANKA
SUDAN
SURINAM
SWAZILAND
SWEDEN
SWITZERLAND
SYRIA
SECAM B
PAL D (was SECAM)
PAL B/SECAM L
SECAM K1
PAL B
SECAM K1
PAL B
PAL B
SECAM K1
PAL B
SECAM K1
SECAM B
SECAM B
NTSC M
SECAM L
SECAM D
SECAM B
PAL B
PAL I
PAL B
PAL B
NTSC M
SECAM K1
PAL B
PAL B
NTSC M
SECAM K1
PAL B
PAL B
PAL B
PAL B
NTSC M
PAL N
NTSC M
NTSC M
PAL D
PAL B
NTSC M
PAL B
SECAM K1
PAL D
SECAM D
SECAM K1
PAL B
NTSC M
NTSC M
SECAM-B/PAL-B
PAL
PAL B
PAL B
PAL B
PAL
PAL B
PAL I
PAL B
PAL B
PAL B
NTSC M
PAL B
PAL B
PAL B
SECAM B
SECAM G
PAL K
PAL G/SEC L
5
5
2
5
PAL G
5
3
5
2
PAL H
NTSC M
5
5
4
2
5
5
5
5
PAL G
NTSC M
2
PAL G
PAL G
NTSC M
4
4
4
5
5
2
2
5
4
4
4
3
2
2
1
2
PAL G
PAL G
PAL G
NTSC M
PAL N
NTSC M
NTSC M
PAL K
PAL G( was SECAM D )
NTSC M
PAL K
SECAM K
English
TV System Guide (continued)
2
5
5
NTSC M
SECAM G
PAL G
PAL G
PAL G
PAL
PAL G
PAL I
PAL G
PAL G
NTSC M
PAL G
PAL G
PAL G
1
2
5
5
5
2
5
2
2
5
5
4
2
2
2
75
English
These Warranty conditions are valid for the following consumer electronics products:
Colour Televisions, Projection TV, Plasma & LCD TV, Video Cassette Recorders, CD Recorders &
Players, DVD Players, DVD Recorders, Audio Systems, Home Theatre systems & Portable Audio.
The benefits given to the purchaser by this warranty are in addition to
all other rights and remedies, which the purchaser has in respect of the
product under the Trade Practices Act or other Commonwealth or State
Law.
Philips Consumer Electronics warrants its products to the purchaser as
follows and subject to the stated conditions.
This warranty does not
cover:
a)
Mileage or travel outside the
normal service area covered by
selected Authorised Service
Centre.
b)
Service costs arising from failure
to correctly adjust the controls of
the product or to observe the
instructions, or inspections that
reveal that the product is in
normal working order.
c)
Product failures caused by
misuse, neglect, accidental
breakage, transit damage,
inexpert repairs or modification
by un-authorised persons,
external fires, lightning strikes,
floods, vermin infestation or
liquid spillage.
d)
Cleaning of video or audio
heads.
e)
Inadequate receiving antennae.
f)
Replacement of worn or used
batteries or other consumables.
g)
Consumer products used in
commercial applications (This
warranty is limited to 3 months
only)
h)
Second hand products.
3 Years Free Repair Service – at Philips ASC
Colour Television, Plasma Television, LCD Television, Projection Television
DVDR/VCR Combo, DVD Recorder, DVD Recorder with Hard Drive, LCD Projectors
Wireless Audio Systems
1 Year Free Repair Service – at Philips ASC
Audio Systems & Home Theatre Systems.
1 Year Free Replacement – at your Retailer
Portable Audio, MP3 Infotainment products, Video Cassette Recorders
DVD Player, DVD/VCR Combo Player, Portable DVD/LCD player.
Conditions of Repair Warranty
1.
All claims for warranty service should be made to your nearest Philips Authorised
Service Centre. Reasonable evidence of date of purchase must be provided.
2.
This warranty extends only to defects in material or workmanship occurring under
normal use of the product when operated in accordance with the instructions.
3.
If a replacement product is supplied under the repair policy it is warranted, under
this warranty, for the remainder of the warranty of the original purchased product
only.
4.
Home service is provided only within the normal service area of one of our
recommended Authorised Service Centres (ASC). It will be provided for television
receivers only, regardless of size or type (i.e. CRT, LCD, PTV, PDP). All other
products are to be taken or sent by the consumer to the workshop of your nearest
ASC (at the Consumer’s expense).
5.
This Manufacturers Warranty is limited to 3 months for above listed Consumer
Electronics products if used in commercial applications.
6.
Philips may, at its discretion choose to replace rather than repair any product
covered by this warranty.
7. This Manufacturers Warranty is neither transferable nor valid in countries other
than Australia.
The conditions contained in this warranty card replace and override the provision of the Philips World-Wide Guarantee for
products purchased in Australia and used in Australia.
Version 6: 1 April 2006
76
Warranty valid for all new products purchased after 1st April 2006
1
English
Philips Consumer Electronics a division of Philips Electronics Australia Limited
ABN 24 008 445 743,
Level 1, 65 Epping Road NORTH RYDE NSW 2113.
Service is provided through more than 100 accredited Authorised Service Centres throughout Australia.
For direct contact with the nearest recommended Authorised Service Centre in capital & regional cities/towns
Authorised Service Centre Network
Customer support is provided in Australia by our trained call centre staff
For assistance with product features and specifications, please call
Technology Care Centre
Please record the following information for your records and keep in a safe place.
We recommend retaining your purchase receipt to assist with any warranty claim
Model number
: ………………………………………………………..
Serial number
: ………………………………………………………..
Date of purchase
: ………………………………………………………..
Retailer
: ………………………………………………………..
Version 6: 1 April 2006
Warranty valid for all new products purchased after 1st April 2006
2
77
English
78
79
English
English
Meet Philips at the Internet
http://www.philips.com
http://www.philips.com/support
DVDR3360H
DVDR3370H
CLASS 1
LASER PRODUCT
3139 246 20532
Sgp-0623/75-1
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising