advertisement
▼
Scroll to page 2
of 20
City Line 2 3 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 2 4 ENGLISH 6 10 CITY LINE 14 6 ENGLISH Important Read these instructions for use carefully before using the appliance and save them for future reference. ◗ ◗ ◗ ◗ ◗ ◗ ◗ ◗ ◗ Check if the voltage indicated on the appliance corresponds to the local mains voltage before you connect the appliance. Do not use the appliance if the plug, the cord or the appliance itself is damaged. If the mains cord is damaged, it must be replaced by Philips, a service centre authorised by Philips or similarly qualified persons in order to avoid a hazard. Keep the appliance out of the reach of children. Never suck up water or any other liquid. Never suck up flammable substances and do not suck up ashes until they are cold. Do not point the hose at the eyes or ears nor put it in your mouth when the vacuum cleaner is switched on and the hose is connected to the vacuum cleaner. When the vacuum cleaner is used to suck up fine dust, the pores of the dustbag may become clogged, causing the passage of air through the dustbag to become obstructed.As a result, the dustbag-full indicator will indicate that the dustbag needs to be replaced, even though the dustbag is not full at all (see chapter 'Replacing the dustbag'). Never use the appliance without the Motor Protection Filter.This could damage the motor and shorten the life of the appliance. Only use Philips s-bag` double-layer paper dustbags. Preparing for use Connecting accessories Hose 1 To connect the hose to the appliance, push it into the appliance and turn it clockwise (fig. 1). 2 To disconnect the hose from the appliance, turn it anticlockwise and pull it out of the appliance. Tube Conical coupling (specific types only) 1 To connect the tube to the handgrip, insert the narrow section into the wider section while turning it a little (fig. 2). 2 To disconnect the tube, pull while turning it a little. Use the same methods to connect the accessories to or to disconnect them from the tube or handgrip. Button coupling (specific types only) 1 Connect the tube to the handgrip ('click') (fig. 3). 2 To disconnect the tube from the handgrip, push the lock button and pull the tube out of the handgrip (fig. 4). Use the same methods to connect the accessories to or to disconnect them from the tube or handgrip. Telescopic tube (specific types only) 1 Adjust the tube to the length you find most comfortable during vacuum cleaning (fig. 5). ENGLISH 7 Nozzle ◗ Convertible nozzle (specific types only) The convertible nozzle can be used on either carpets or hard floors. 1 Connect the convertible nozzle to the tube. 2 Push the rocker switch on top of the convertible nozzle with your foot to make the brush strip for cleaning hard floors come out of the nozzle housing (fig. 6). 3 Push the rocker switch again to make the brush strip disappear into the convertible nozzle housing (fig. 7). ◗ ◗ Reach & Clean nozzle (specific types only) The Reach & Clean nozzle can be used on either carpets or hard floors.The nozzle can be turned 360 degrees to 4 different positions, allowing you to also vacuum clean hard-to-reach places in an easy way.When the nozzle is positioned lengthwise, the suction power is concentrated at the front side of the nozzle (fig. 8). To adjust the nozzle to the type of floor and the area to be cleaned, put your foot on the indicated spot and then turn the tube until the nozzle is in the required position (fig. 9). 1 Connect the Reach & Clean nozzle to the tube. 2 With the nozzle positioned breadthwise and the brush strip folded out, you can clean large hard floor areas.Turn the tube until the brush strip pops out of the nozzle housing and the nozzle is positioned breadthwise (fig. 10). 3 With the nozzle positioned lengthwise and the brush strip folded out, you can vacuum clean small hard floor areas.Turn the tube 90 degrees anti-clockwise until it is positioned lengthwise with the brush strip still folded out of the nozzle housing (fig. 11). 4 With the nozzle positioned breadthwise and the brush strip folded in, you can vacuum clean large soft floor areas.Turn the tube 90 degrees anti-clockwise again to position the nozzle breadthwise and to make the brush strip disappear into the nozzle housing (fig. 12). 5 With the nozzle positioned lengthwise and the brush strip folded in, you can vacuum clean small soft floor areas.Turn the tube 90 degrees anti-clockwise again until it is positioned lengthwise with the brush strip still folded in (fig. 13). Crevice tool, small nozzle and small brush (specific types only) 1 Connect the crevice tool, small nozzle or small brush directly to the handgrip or to the tube. Accessory clip (specific types only) ◗ ◗ The accessory clip can simply be snapped onto the tube. The crevice tool and the small nozzle can be snapped onto the clip (fig. 14). Using the appliance Vacuum cleaning 1 Pull the cord out of the appliance and put the mains plug in the wall socket (fig. 15). 2 Switch the appliance on by pushing the on/off button on top of the appliance with your foot. 3 The appliance can be carried in two ways: ◗ ◗ You can carry the vacuum cleaner vertically by the handle on the front of the appliance (fig. 16). You can carry the vacuum cleaner horizontally by the handle on top of the appliance. 8 ENGLISH Adjusting suction power You can adjust the suction power while vacuum cleaning. 1 Adjust the suction power by means of the electronic suction power knob (fig. 17). 2 Turn the knob to MAX for maximum suction power (fig. 18). Use maximum suction power for vacuum cleaning very dirty carpets and hard floors. 3 Turn the knob to MIN for minimum suction power. Use minimum suction power for vacuum cleaning curtains, table carpets, etc. Storage 1 Switch the appliance off and remove the mains plug from the wall socket. 2 Rewind the mains cord by pressing the cord rewind button (fig. 19). 3 Put the appliance in upright position and attach the nozzle to the appliance by inserting the ridge on the nozzle into the slot (fig. 20). Replacing the dustbag ◗ Replace the dustbag as soon as the dustbag-full indicator has changed colour permanently, i.e. even when the nozzle is not placed on the floor (fig. 21). 1 Switch the appliance off and open the cover (fig. 22). 2 Push the dustbag holder backwards (fig. 23). 3 Remove the full dustbag from the holder by pulling it up by the cardboard tag, which will cause the dustbag to be sealed (fig. 24). 4 Slide the cardboard front of the new dustbag into the two grooves of the dustbag holder. Press it down as far as possible (fig. 25). 5 Pull the dustbag holder forwards ('click') (fig. 26). You cannot close the cover if no dustbag has been inserted. Ordering dustbags Philips Classic s-bag` paper dustbags are available under type number FC8021. Replacing filters Motor Protection Filter Replace the Motor Protection Filter once a year. 1 Switch the appliance off and open the cover. Remove the filter. 2 Insert a new filter into the holder with the white side pointing towards the dustbag compartment (fig. 27). Super Clean Air Filter (specific types only) Replace the Super Clean Air Filter every 6 months. 1 Open the grille at the back of the appliance and remove it (fig. 28). 2 Remove the old filter and place the sides and the bottom edge of the new filter properly behind the ridges of the holder on the inside of the grille. ENGLISH 9 3 Put the grille back into the vacuum cleaner by first hooking the bottom edge of the grille into the appliance (1) and then pushing the grille towards the appliance (2) until it snaps home (fig. 29). Super Clean Air HEPA Filter (specific types only) Instead of the Super Clean Air Filter, some types are equipped with the special Super Clean Air HEPA Filter.This filter not only removes household dust, but also harmful microscopic vermin. Replace the Super Clean Air HEPA Filter every 6 months. 1 Open the filter grille and remove the Super Clean Air HEPA Filter. 2 Place the new filter behind the brackets. Make sure that the Philips logo on the filter is visible in the bottom right-hand corner (fig. 30). 3 Close the filter grille. Ordering filters Two Super Clean Air Filters and one Motor Protection Filter are available under type number FC8032. Super Clean Air HEPA Filters are available under type number FC8044. Troubleshooting ◗ Insufficient suction power 1 Check if the dustbag needs to be replaced. 2 Check if the filters need to be replaced. 3 Check if the electronic suction power knob is in maximum position. 4 Check if the nozzle, tube or hose is blocked up. 5 To remove the obstruction, disconnect the blocked-up item and connect it (as far as possible) in reverse position (fig. 31). 6 Switch the vacuum cleaner on to force the air through the blocked-up item in opposite direction. Make the airflow suck the obstructing material out of the blocked-up item. Guarantee & service If you need information or if you have a problem, please visit the Philips website at www.philips.com or contact the Philips Customer Care Centre in your country (you will find its phone number in the worldwide guarantee leaflet). If there is no Customer Care Centre in your country, turn to your local Philips dealer or contact the Service Department of Philips Domestic Appliances and Personal Care BV. 10 ◗ ◗ ◗ ◗ ◗ ◗ ◗ ◗ ◗ 1 2 1 2 1 2 1 ◗ 1 2 3 ` 11 ◗ ◗ 1 2 3 4 5 1 ◗ ◗ 1 2 3 ◗ ◗ 1 2 3 1 2 3 12 ◗ 1 2 3 4 5 1 2 1 2 3 1 2 3 13 ◗ 1 2 3 4 5 6 14 ◗ ◗ ◗ ◗ ◗ ◗ ◗ ◗ ◗ ` 15 ◗ ◗ ◗ ◗ ◗ ◗ ◗ 16 ◗ ` 17 ◗ 18 21 22 23 24 25 26 27 28 29 30 31 19 u www.philips.com 4222 003 32942
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Key Features
- Cylinder vacuum 2 L 1800 W White
- Dry Dust bag
- Micro, HEPA Filtering 79 dB
- Dust container full indicator Operating radius: 9 m
- Carrying handle(s)