Samsung | LW29A13W | Samsung LW29A13W User Manual

apollo_en
12/23/02 5:24 PM
Page 1
LCD TV
LW29A13W
LW40A13W
Owner’s Instructions
Before operating the unit,
please read this manual thoroughly,
and retain it for future reference.
ON-SCREEN MENUS
PC DISPLAY
PICTURE IN PICTURE (PIP)
PICTURE BY PICTURE (PBP)
TELETEXT
apollo_en
12/23/02 5:24 PM
Page 2
Information in this document is subject to change without notice.
© 2002 Samsung Electronics Co., Ltd. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Samsung
Electronics Co., Ltd. is strictly forbidden.
Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for
incidental or consequential damages in connection with the furnishing, performance, or
use of this material.
The Samsung logo is the registered trademarks of Samsung Electronics Co., Ltd.;
Microsoft, Windows® and Windows® NT are registered trademark of Microsoft
Corporation; VESA, DPMS and DDC are registered trademarks of Video Electronics
Standard Association. All other product names mentioned herein may be the trademarks
or registered trademarks of their respective owners.
Plug and Play
The adoption of the new VESA® Plug and Play solution eliminates complicated and time
consuming setup. It allows you to install your set in a Plug and Play compatible system
without the usual hassles and confusion. Your computer system can easily identify and
configure itself for use with your set.
Your set automatically tells the computer system its Extended Display Identification Data
(EDID) using Display Data Channel (DDC) protocols so the computer system can
automatically configure itself to use your set. If your PC system needs a monitor driver,
install monitor driver contained on the accompanied CD according to the operating
system your computer uses. For more information, refer to the driver installation
instructions included with your CD package.
PowerSaver
This set is EPA ENERGY STAR® compliant and NUTEK compliant when used with a
computer equipped with VESA DPMS functionality. For energy conservation, turn your set
Off when you are not using it or when leaving it unattended for long periods.
European Notice
Products with the CE Marking comply with both the EMC Directive (89/336/EEC),
(92/31/EEC), (93/68/EEC) and the Low Voltage Directive (73/23/EEC) issued by the
Commission of the European Community. Compliance with these directives implies
conformity to the following European Norms:
■ EN55022:1998 – Radio Frequency Interference
■ EN55024:1998 – Electromagnetic Immunity
■ EN61000-3-2:1995 + A1 + A2 – Power Line Harmonics
■ EN61000-3-3:1995 – Voltage Fluctuations
■ EN60950 – Product Safety.
English-2
apollo_en
12/23/02 5:24 PM
Page 3
Safety Instructions
These illustrations represent precautions concerning your set.
75%
40°
H
10%
H
5°
Do NOT expose your set to
extreme temperature or
humidity conditions.
Do NOT expose your set to
direct sunlight.
Do NOT expose your set to
any liquids.
If your set is broken, do not try
to repair it yourself. Contact
qualified service personnel.
During storm conditions
(especially when there is
lightning) unplug your set from
the mains socket and aerial.
If the remote control is not
used for a long period of time,
remove the batteries and store
it in a cool, dry place.
THIS DEVICE IS NOT FOR USE IN INDUSTRIAL ENVIRONMENTS
Caution
CAUTION
RISK OF ELECTRIC
SHOCK DO NOT OPEN
CAUTION: TO PREVENT ELECTRICAL SHOCK,
DO NOT REMOVE REAR COVER, NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash and arrow head
within the triangle is a warning
sign alerting you of “dangerous
voltage” inside the product.
The exclamation point within the
triangle is a warning sign alerting
you of important instructions
accompanying the product.
WARNING: TO PREVENT DAMAGE WHICH MAY RESULT IN FIRE OR SHOCK HAZARD, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
☛
The main voltage is indicated on the rear of your set and the frequency is 50 or 60 Hz.
English-3
apollo_en
12/23/02 5:24 PM
Page 4
Contents
◆ FOREWORD
■
■
Safety Instructions ..........................................................................................
Caution ..........................................................................................................
3
3
◆ CONNECTING AND PREPARING YOUR TV
■
■
■
■
■
■
■
■
■
Viewing the Control Panel..............................................................................
Viewing the Connection Panel .......................................................................
- Connecting an Aerial or Cable Television Network.....................................
- Connecting External A/V Devices ...............................................................
- Connecting DTV Set-Top Box, VCR, or DVD ..............................................
- Connecting Computer.................................................................................
- Connecting Sound Outputs .........................................................................
- Connecting Digital Audio Inputs .................................................................
- Connecting Speakers...................................................................................
Viewing Pictures From External Sources .........................................................
Viewing the Remote Control (All Functions Except Teletext)...........................
Viewing the Remote Control (Teletext Functions) ...........................................
Inserting the Batteries in the Remote Control..................................................
Switching On and Off ....................................................................................
Becoming Familiar with the Remote Control..................................................
Choosing Your Language ................................................................................
◆ SETTING
■
■
■
■
■
■
◆ USING
■
■
■
■
■
■
■
■
English-4
THE
CHANNELS
Storing Channels Automatically......................................................................
Storing Channels Manually.............................................................................
Giving Channels Names.................................................................................
Skipping Unwanted Channels ........................................................................
Fine Tuning Channel Reception......................................................................
Sorting the Stored Channels ...........................................................................
THE
6
7
8
8
8
8
8
9
9
9
10
11
12
12
13
14
15
16
18
19
19
20
VARIOUS FUNCTIONS
Changing the Picture Standard .......................................................................
Adjusting the Picture Settings .........................................................................
Selecting the Picture Format...........................................................................
Freezing the Current Picture...........................................................................
Changing the Sound Standard ........................................................................
Adjusting the Sound Settings ..........................................................................
Enjoying the Dolby Sound (LW29A13W) .......................................................
Switching the Internal Woofers On/Off (LW29A13W) ....................................
21
21
22
22
23
23
24
24
apollo_en
12/23/02 5:24 PM
Page 5
Contents
◆ USING
■
■
■
■
■
■
■
■
■
◆ USING
■
■
■
■
■
■
■
■
◆ USING
■
■
■
■
THE
VARIOUS FUNCTIONS
Setting the External Digital Sound (LW40A13W) ............................................
Setting the Dolby Digital (LW40A13W)..........................................................
Setting the Dolby Pro-Logic (LW40A13W) .....................................................
Selecting the Sound Mode..............................................................................
Viewing the Picture In Picture (PIP) ................................................................
Selecting the Sleep Timer ...............................................................................
Setting and Displaying the Current Time ........................................................
Switching the Television On and Off Automatically .......................................
DNIe (Digital Natural Image engine) .............................................................
THE
PC FUNCTIONS
Setting up Your PC Softerware (Based on Windows 2000 or XP) ....................
Adjusting the Contrast and Brightness ............................................................
Selecting the Image Size.................................................................................
Adjusting the Image Quality...........................................................................
Changing the Image Position..........................................................................
Adjusting the Colour ......................................................................................
Initializing the Image Settings.........................................................................
Adjusting the PC Screen Automatically ..........................................................
THE
25
26
27
28
29
31
32
33
34
35
36
36
37
37
38
39
39
TELETEXT FEATURE
Teletext Feature ..............................................................................................
Displaying the Teletext Information ................................................................
Selecting Display Options ..............................................................................
Selecting a Teletext Page ................................................................................
40
41
41
42
◆ RECOMMENDATIONS FOR USE
■
■
■
■
■
Troubleshooting: Before Contacting Service Personnel ...................................
PowerSaver ....................................................................................................
Technical and Environmental Specifications...................................................
Display Modes ...............................................................................................
Wiring the Mains Power Supply Plug (UK Only) ............................................
Symbols
Press
☛
➢
Important
Note
43
44
45
46
47
English-5
apollo_en
12/23/02 5:24 PM
Page 6
Viewing the Control Panel
1
(Power)
Turns ON/OFF your set.
2 Power Indicator
3 Remote Control Sensor
4 TV/VIDEO
Displays a menu of all of the available input
sources (TV, VIDEO, S-VIDEO, EXT1, EXT2,
PC Analog, PC Digital).
English-6
5 MENU
Opens the OSD and selects the function.
6 ▼ C/P. ▲
Moves the selector up or down on the OSD.
Increases or decreases the channel number.
Switches on the TV when it is in Standby mode.
+
7 Moves the selector left or right on the OSD.
Increases or decreases the level of audio volume
and the values of the selected function.
apollo_en
12/23/02 5:24 PM
Page 7
Viewing the Connection Panel
LW29A13W
7
8
1
3
2
5
4
Power Input
LW40A13W
6
5
☛
Whenever you connect an audio or video system to your set, ensure that all elements are switched
off. Refer to the documentation supplied with your equipment for detailed connection instructions
and associated safety precautions.
English-7
apollo_en
12/23/02 5:24 PM
Page 8
Viewing the Connection Panel
1
Connecting an Aerial or Cable Television Network
To view television channels correctly, a signal must be received by the set from one of the following sources:
- An outdoor aerial
- A cable television network
- A satellite network
2
Connecting External A/V Devices
- Connect RCA or S-VIDEO cable to an appropriate external A/V device such as VCR, DVD, or Camcorder.
- Connect RCA audio cables to “AUDIO(L)” and “AUDIO(R)” on the rear of your set and the other ends to
corresponding audio out connectors on the A/V device.
- Headphone may be connected to the headphone output ( 8 ) on the rear of your set. While the headphone
is connected, the sound from the built-in speakers will be disabled.
3
Connecting DTV Set-Top Box, VCR, or DVD
- Connect the DTV, VCR, or DVD EXT cable to the EXT connector of the DTV, VCR, or DVD.
- If you wish to connect both the DTV Set-Top Box and VCR (or DVD), you should connect the DTV Set-Top
Box to the VCR (or DVD) and connect the VCR (or DVD) to your set.
4
Connecting Computer
- Connect the DVI connector to the PC video connector.
- Connect the stereo audio cable to ”PC AUDIO(ST)” on the rear of your set and the other end to “Audio Out”
of the sound card on your computer.
➣
5
DVI connector
Pin
Description
Pin
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Rx 2Rx 2+
Grounding
No connection
No connection
DDC Clock (SCL)
DDC Data (SDA)
Analog Vertical Sync
Rx 1Rx 1+
Grounding
No connection
No connection
DDC Input Power (+5V)
Self Laster
16
17
18
19
20
21
22
23
24
25(C3)
26(C5)
27(C4)
28(C2)
29(C5)
30(C1)
Output Signal Connection
Rx 0Rx 0+
Grounding
No connection
No connection
Grounding
Rx CRx C+
Analog (Blue)
Analog Grounding
Analog Horizontal sync.
Analog (Green)
Analog Grounding
Analog (Red)
Connecting Sound Outputs
Connect RCA audio cables to an audio system or external amplifier.
English-8
apollo_en
12/23/02 5:24 PM
Page 9
Viewing the Connection Panel
6
Connecting Digital Audio Inputs
Connect RCA audio cables to a equipment with a digital output (to take digital sound).
Connecting Speakers (depending on the model)
7
Connect the speaker audio cable to the external
speaker output jack on the rear of your set making
sure that the +, - polarities are correctly aligned.
➢
The speakers MUST have more than 7watts
rating (impedance 8Ω).
or
Mount the brackets on the speaker
and your set.
Connect the speaker and your set
using screws.
Viewing Pictures From External Sources
Once you have connected up your various audio and video systems,
you can view the different sources by selecting the appropriate input.
1
Check that all the necessary connections have been made (refer to
pages 8 and 9 for further details).
2
Switch your set on and if necessary, press the VIDEO button
repeatedly. The input sources are displayed in the following order:
TV - VIDEO - S-VIDEO - Ext1 - Ext2 - PC Analog - PC Digital.
➣
To watch television programme again, press the TV button.
English-9
apollo_en
12/23/02 5:24 PM
Page 10
Viewing the Remote Control (All Functions Except Teletext)
Automatic switch-off
VCR/DVD Functions:
- Stop
- Rewind
- Play/Pause
- Fast-Forward
Television On/Off
Numeric buttons for
direct channel access
Picture freeze
(Not Available in PC mode)
PIP
Picture-In-Picture Functions:
- PIP On/Off
- PIP size selection (SIZE)
- PIP channel selection (P▲/▼)
(Not available for LW29A13W)
- Interchange the main and sub picture
(SWAP)
- PIP freeze (STILL) : Not available
- PIP location selection (LOCATE)
- PIP channel scan (SCAN)
- PIP source selection (TV/VIDEO)
Make the remote control work for
TV, VCR, Cable, DVD player.
One/Two-digit channel selection
On-screen display
TV mode selection directly
Next channel
Volume decrease
Temporary sound switch-off
Available sources selection
Menu display/
Exit from the OSD
Volume increase
Previous channel
Sound mode selection
Picture size selection
Picture menu display
Not available
Picture effect selection
Sound menu display
Sound effect selection
➣
English-10
The performance of the remote control may be affected by bright light.
apollo_en
12/23/02 5:24 PM
Page 11
Viewing the Remote Control (Teletext Functions)
PIP
Teletext reveal
Teletext index
Teletext display/
Mix both teletext information and
the normal broadcast
Teletext sub-page
Teletext size selection
Fastext topic selection
English-11
apollo_en
12/23/02 5:24 PM
Page 12
Inserting the Batteries in the Remote Control
You must insert or replace the batteries in the remote control when
you:
◆ Purchase your set
◆ Find that the remote control is no longer operating
correctly
1
Remove the cover on the rear of the remote control by pressing the
symbol downwards and then pulling firmly to remove it.
2
Insert two R03, UM4, “AAA” 1.5V or equivalent batteries taking care to
respect the polarities:
◆ + on the battery against + on the remote control
◆ - on the battery against - on the remote control
3
Replace the cover by aligning it with the base of the remote control
and pressing it back into place.
➣
Do not mix battery types, i.e. alkaline and monganese.
Switching On and Off
The mains lead is attached to the rear of your set.
☛
If you have purchased this set in the United Kingdom, refer to
page 45 for further instructions on plug wiring.
1
Plug the mains lead into an appropriate socket.
A green Standby indicator appears on the front of your set.
Result:
2
Press the POWER ( ) or channel up/down (P / , ▼C/P. ▲)
button.
The screen is turned on and a green Standby indicator
Result:
disappears on the front of your set.
Your set can be placed in Standby mode, in order to reduce the power
consumption. The Standby mode can be useful when you wish to
interrupt viewing temporarily (during a meal, for example).
1
Press the POWER ( ) button.
The screen is turned off and a green Standby indicator
Result:
appears on the front of your set.
2
To switch your set back on, simply press the POWER (
again.
➣
English-12
) button
Do not leave your set in Standby mode for long periods of time
(when you are away on holiday, for example). Turn your set off by
unpluging from the mains and aerial.
apollo_en
12/23/02 5:24 PM
Page 13
Becoming Familiar with the Remote Control
The remote control is used mainly to:
◆ Change channels and adjust the volume
◆ Set up your set using the on-screen menu system
The following table presents the most frequently used buttons and
their functions.
PIP
Button
Viewing Function
Menu Function
Used to display the next
stored channel.
Used to select the previous
menu option.
P
Used to display the
previous stored channel.
Used to select the next menu
option.
to
Used to display the corresponding channels.
P
-/--
MUTE
Used to select a channel numbered ten or over.
Press this button, and the “--” symbol is displayed.
Enter the two-digit channel number.
Used to decrease the
volume.
Used to...
◆ Display a submenu containing
selections for the current
menu option.
◆ Search forwards manually
for channels
◆ Reduce a menu option value.
Used to increase the
volume.
Used to...
◆ Display a submenu containing
selections for the current
menu option.
◆ Search backwards manually
for channels
◆ Increase a menu option value.
Used to switch the sound off temporarily.
➣
MENU
To turn the sound back on, press this button again,
+ button.
- or
or press the
Used to display the
on-screen menu system.
Used to return to the previous
menu or normal viewing.
English-13
apollo_en
12/23/02 5:24 PM
Page 14
Choosing Your Language
When you start using your set for the first time, you must select the
language which will be used for displaying menus and indications.
1
Press the MENU button.
Result:
2
Press the P
Result:
Function
Time
PIP
Language
DNIe
English
Off
English-14
The main menu is displayed.
or P
button to select the Function.
The options available in the Function group are
displayed.
+ button.
3
Press the
4
Press the P
5
Select a particular language by pressing the
repeatedly.
6
When you are satisfied with your choice, press the MENU button to
return to normal viewing.
- or
or P
button to select the Language.
- or
+ button
apollo_en
12/23/02 5:24 PM
Page 15
Storing Channels Automatically
You can scan for the frequency ranges available to you (and
availability depends on your country). Automatically allocated
programme numbers may not correspond to actual or desired
programme numbers. However you can sort numbers manually and
clear any channels you do not wish to watch.
1
Channel
Auto store
Manual store
Name
Add/Erase
Fine tune
Channel sort
Press the MENU button.
Result:
The main menu is displayed.
Channel
2
Press the P
Result:
3
Press the
Result:
4
Press the
Result:
or P
button to select the Channel.
The options available in the Channel group are displayed.
- or
The Auto store is selected.
- or
+ button again.
The options available in the Auto store group are
displayed when the Country is selected.
+ button repeatedly.
- or
Select your country by pressing the
The following countries are available:
Belgie - Deutschland - Espania - France - Italia - Nederland
- Schweiz - Sverige - UK - East Europe.
6
Press the P
- or
the
➣
7
UK
+ button.
5
Result:
Country
Search
Channel
Country
Search
UK
or P
button to select the Search, and then press
+ button.
The search will end automatically. Channels are sorted
and stored in an order which reflects their position in the
frequency range, (with lowest first and highest last).
The programme originally selected is then displayed.
Search
Program
Frequency
Band
1
205MHz
VHF-H
To stop the search before it has finished, press the MENU
button.
When the channels have been stored, you can:
◆ Change channels
◆ Assign a name to the stored channels (refer to page 18)
◆ Clear a channel (refer to page 19)
◆ Fine tune channel reception if necessary (refer to page 19)
◆ Sort them in the order required (refer to page 20)
English-15
apollo_en
12/23/02 5:24 PM
Page 16
Storing Channels Manually
Channel
Auto store
Manual store
Name
Add/Erase
Fine tune
Channel sort
You can store up to 100 channels, including those received via cable
networks. When storing channels manually, you can choose:
◆ Whether or not to store each of the channels found
◆ The programme number of each stored channel which you
wish to identify
1
Channel
Colour system
Sound system
Search
Channel
Program
LNA
Store
AUTO
BG
0MHz
C 1
P 1
Off
?
Result:
2
AUTO
BG
0MHz
C 1
P 1
Off
?
Press the P
Result:
Press the P
or P
- or
Press the
Result:
5
English-16
6
button to select the Channel.
The options available in the Channel group are displayed.
4
- or
+ button.
button to select the Manual store.
+ button.
The options available in the Manual store group are
displayed with the Colour system is selected.
If necessary, indicate the broadcasting standard required by pressing
+ button repeatedly.
- or
the
Channel
AUTO
BG
0MHz
C 1
P 1
Off
?
or P
Press the
Result:
Colour system
Sound system
Search
Channel
Program
LNA
Store
The main menu is displayed.
3
Channel
Colour system
Sound system
Search
Channel
Program
LNA
Store
Press the MENU button.
The colour standards are displayed in the following order:
AUTO - PAL - SECAM - NT4.43.
Press the P
or P
button to select the Sound system. Indicate
+ button
- or
the sound standard required by pressing the
repeatedly.
Result:
The sound standards are displayed in the following order:
BG - DK - I - L.
apollo_en
12/23/02 5:24 PM
Page 17
Storing Channels Manually
Channel
Colour system
Sound system
Search
Channel
Program
LNA
Store
7
If you know the channel number to be stored, press the P
or P
button to select the Channel. Indicate the required number by
+ button.
- or
pressing the
If you do not know the channel numbers, press the P
button to select the Search.
+ button.
- or
Start the search by pressing the
Result:
8
9
Press the P
or P
button to select the LNA..(LW40A13W)
+ button.
- or
Select the On by pressing the
Amplifies signals when antenna reception is poor.
However if incoming signals are interfering with each
other, turn off LNA as it may malfuction.
Press the P
or P
button to select the Store.
+ button.
- or
Select the OK by pressing the
Result:
11
The tuner scans the frequency range until the first
channel or the channel that you selected is received on
your screen.
To assign a programme number to a channel, select the Program by
pressing the P
or P
button.
+ button to find the correct number.
- or
Press the
Result:
10
or P
The channel and associated programme number are
stored.
Repeat Steps 7 to 9 for each channel to be stored.
AUTO
BG
0MHz
C 1
P 1
Off
?
Channel
Colour system
Sound system
Search
Channel
Program
LNA
Store
AUTO
BG
0MHz
C 1
P 1
Off
?
Channel
Colour system
Sound system
Search
Channel
Program
LNA
Store
AUTO
BG
0MHz
C 1
P 1
ON
?
Channel
Colour system
Sound system
Search
Channel
Program
LNA
Store
English-17
AUTO
BG
0MHz
C 1
P 1
ON
?
apollo_en
12/23/02 5:24 PM
Page 18
Giving Channels Names (Except Russian OSD)
If channel name information is broadcast when you store the channels
either manually or automatically, the names are assigned to the
channels directly. You can however change these names or assign new
names as required.
1
Press the MENU button.
Result:
2
Press the P
Result:
or P
button to select the Channel.
The options available in the Channel group are displayed.
3
Press the
4
Press the P
or P
- or
Press the
Result:
English-18
The main menu is displayed.
- or
+ button.
button to select the Name.
+ button.
The current channels are displayed.
5
If necessary, select the channel to be assigned to a new name by
pressing the P
or P
button.
6
Press the
7
Press the P
or P
button to select a letter (A~Z), a number
(0~9) or a symbol (-, space).
+
- or
Move on the previous or next letter by pressing the
button.
8
Repeat Steps 5 to 7 for each channel to be assigned to a new
name.
- or
+ button.
apollo_en
12/23/02 5:24 PM
Page 19
Skipping Unwanted Channels
You can exclude the channels you chosen from the channels you
scanned. When you scan through the stored channels, those you have
chosen to skip are not displayed.
All channels that you do not specifically choose to skip are displayed
during scanning.
1
Press the MENU button.
Result:
2
Press the P
Result:
The main menu is displayed.
or P
The options available in the Channel group are displayed.
3
Press the
4
Press the P
or P
+ button.
- or
Result:
button to select the Channel.
- or
+ button.
button to select the Add/Erase. Press the
The stored channels are displayed.
5
Press the P
or P
button to select the channel to add or erase.
- or
If necessary, select the Added or Erased by pressing the
+ button.
6
Repeat Step 5 for each channel to be added or erased.
Fine Tuning Channel Reception
If the reception is clear, you do not have to fine-tune the channel,
as this is done automatically during the search and store operation.
If however the signal is weak or distorted, you may have to fine-tune
the channel manually.
1
Press the MENU button.
Result:
2
Press the P
Result:
Channel
Auto store
Manual store
Name
Add/Erase
Fine tune
Channel sort
The main menu is displayed.
or P
button to select the Channel.
Fine tune
The options available in the Channel group are displayed.
+ button.
3
Press the
4
Press the P
5
Obtain a sharp and clear picture and good sound quality by pressing
+ button.
- or
the
- or
or P
+ 1
button to select the Fine tune.
English-19
apollo_en
12/23/02 5:24 PM
Page 20
Sorting the Stored Channels
Channel
You can exchange the numbers of two channels, in order to:
◆ Modify the numeric order in which the channels have been
automatically stored.
Auto store
Manual store
Name
Add/Erase
Fine tune
Channel sort
◆ Give easily remembered numbers to the channels that you
watch most often.
1
Result:
Channel sort
From
To
Store
P 1 ----P-?
2
P 1 ----P 3 ----?
Channel sort
From
To
Store
The main menu is displayed.
or P
Press the
4
Press the P
or P
- or
Press the
Result:
button to select the Channel.
The options available in the Channel group are displayed.
3
- or
+ button.
button to select the Channel sort.
+ button.
The options available in the Channel sort group are
displayed with the From is selected.
5
Select the channel number that you wish to change by pressing the
+ button repeatedly.
- or
6
Press the P
or P
button to select the To. Select the new
number by which you wish to identify the channel by pressing the
+ button repeatedly.
- or
7
Press the P
or P
button to select the Store. Select the OK to
confirm the exchange of channel numbers by pressing the
+ button.
- or
P 3 ----P 1 ----OK
Result:
8
English-20
Press the P
Result:
Channel sort
From
To
Store
Press the MENU button.
The selected channel is exchanged with the one
previously stored to the chosen number.
For all the channels to move to the required channel numbers,
repeat steps 5 to 7 after select the From by pressing the
P
or P
button.
apollo_en
12/23/02 5:25 PM
Page 21
Changing the Picture Standard
You can select the type of picture which best corresponds to your
viewing requirements.
1
Press the MENU button.
The main menu is displayed.
Result:
2
Press the P
or P
button to select the Picture.
The options available in the Picture group are displayed.
Result:
➣
Picture
Mode
Custom
Contrast
Brightness
Sharpness
Colour
Colour tone
Normal
You can also display simply by pressing the P.MENU (Picture
Menu) button.
3
+ button.
- or
Press the
The Mode is selected.
Result:
4
+
- or
Select the required picture effect by pressing the
button repeatedly. The following picture effects are available:
Dynamic - Standard - Movie - Custom.
➣
➣
You can also set these options simply by pressing the P.STD
(Picture Standard) button.
On the Picture menu, if you change the Contrast, Brightness,
Sharpness, Colour or Tint (NTSC only) settings, the Custom is
selected automatically.
Adjusting the Picture Settings
Your set has several settings which allow you to control picture quality.
1
Press the MENU button.
The main menu is displayed.
Result:
2
Press the P
or P
button to select the Picture.
The options available in the Picture group are displayed.
Result:
Press the
4
Select the option (Contrast, Brightness, Sharpness, Colour or
Tint-NTSC only) to be adjusted by pressing the P
or P
+ button.
- or
button. Press the
The horizontal bar is displayed.
Result:
5
6
Press the
- or
Colour tone
Normal
+ button.
3
- or
Picture
Mode
Custom
Contrast
Brightness
Sharpness
Colour
Contrast
70
Picture
+ button to reach the required setting.
Press the P
or P
button to select the Colour tone. Select the
+ button repeatedly.
- or
required option by pressing the the
The following options are available:
Mode
Custom
Contrast
Brightness
Sharpness
Colour
Cool2 - Cool 1 - Normal - Warm 1 - Warm2.
Colour tone
➣
If you make any changes to these settings, the picture standard is
automatically switched to Custom.
English-21
Normal
apollo_en
12/23/02 5:25 PM
Page 22
Selecting the Picture Format
You can select the picture format which best corresponds to your
viewing requirements simply by pressing the “P.SIZE” (Picture Size)
button.
The following picture formats are available:
◆ 16:9
Sets the Normal picture in 16:9 Wide mode.
◆ Panorama
Sets the picture in 16:9 Wide mode so that it
can be shown like the Normal picture.
◆ Zoom 1
Expands the 4:3 aspect ratio screen size.
◆ Zoom 2
Expands the Zoom 1 screen size.
◆ 4:3
Setting for normal 4:3 format.
◆ Auto Wide
The screen size is automatically adjusted
when entering a PAL Plus signal(WSS).
➣
◆ This feature does not work while the PIP feature is activating
◆ When the picture size is selected to 16:9, the PIP feature will
work.
Freezing the Current Picture
➣
Not Available in PC mode.
Press the “STILL PICTURE” button on the remote control to freeze the
picture on a given frame.
When PIP is active, PIP screen is also frozen.
To return to normal viewing, press the “STILL PICTURE” button again.
PIP
English-22
apollo_en
12/23/02 5:25 PM
Page 23
Changing the Sound Standard
You can select the type of special sound effect to be used when
watching a given broadcast.
1
The main menu is displayed.
Press the P
Result:
➣
3
or P
button to select the Sound.
The options available in the Sound group are displayed.
You can also display simply by pressing the S.MENU
(Sound Menu) button.
- or
Press the
Result:
4
Custom
Press the MENU button.
Result:
2
Sound
Mode
Bass
Treble
+ button.
The Mode is selected.
+
- or
Select the required sound effect by pressing the
button repeatedly. The following sound effects are available:
Custom - Standard - Music - Movie - Speech.
➣
You can also set these options simply by pressing the S.STD
(Sound Standard) button.
Adjusting the Sound Settings
The sound settings can be adjusted to suit your personal preferences.
1
Press the MENU button.
Result:
2
Press the P
Result:
Sound
Mode
Bass
Treble
Custom
The main menu is displayed.
or P
button to select the Sound.
The options available in the Sound group are displayed.
+ button.
3
Press the
4
Select the option (Bass or Treble) to be adjusted by pressing the
+ button.
- or
P
or P
button. Press the
- or
Bass
47
Result:
5
Press the
➣
The horizontal bar is displayed.
- or
+ button to reach the required setting.
If you make any changes to these settings, the sound standard is
automatically switched to Custom.
English-23
apollo_en
12/23/02 5:25 PM
Page 24
Enjoying the Dolby Sound (LW29A13W)
Sound
Mode
Bass
Treble
Dolby
Woofer
Custom
:
:
On
Off
This feature provides a home theater-like Dolby effect by mixing the
left and right speakers.
1
Press the MENU button.
Result:
2
Press the P
Result:
The main menu is displayed.
or P
button to select the Sound.
The options available in the Sound group are displayed.
+ button.
3
Press the
4
Press the P
5
For enjoying the Dolby sound effect, select the On by pressing the
+ button.
- or
- or
or P
button to select the Dolby.
Switching the Internal Woofers On/Off (LW29A13W)
Sound
Mode
Bass
Treble
Dolby
Woofer
Custom
:
:
On
On
When the internal woofers are switched off, all the sound is routed to
the external woofers.
1
Press the MENU button.
Result:
2
Press the P
Result:
English-24
The main menu is displayed.
or P
button to select the Sound.
The options available in the Sound group are displayed.
+ button.
3
Press the
4
Press the P
5
Select the On to be routed the sound to the internal woofers by
+ button.
- or
pressing the
- or
or P
button to select the Woofer.
apollo_en
12/23/02 5:25 PM
Page 25
Setting the External Digital Sound (LW40A13W)
You can enjoy Digital sound when the equipment with Digital output
is connected to the television.
1
Press the MENU button.
The main menu is displayed.
Result:
2
Press the P
or P
button to select the Sound.
The options available in the Sound group are displayed.
Result:
3
Press the
4
Press the P
or P
button to select the Ext. audio.
+ button.
- or
Press the
The Ext. audio menu is displayed.
Result:
- or
+ button.
5
Select the required output (EXT1, EXT2, S-video or Video) by
+ button.
- or
pressing the
6
Select the option (Analog, Optical or Coaxial) by pressing
+ button.
- or
the
7
Press the MENU button.
The options available in the Sound group are displayed
Result:
again.
8
Press the P
9
Select the required option (Volume or Fixed) by pressing
+ button.
- or
the
or P
button to select the Audio out.
◆ If you want to adjust the volume level with the volume control on
the TV or external amplifier, set to Volume.
◆ If you set to Fixed...
- You can adjust the volume level with the volume control on the
audio amplifier. And the Int. mute is set to On automatically,
and you can not select it.
- The following controls are not available: volume, bass, treble,
and speaker setting.
10
Press the P
or P
button to select the Int. mute.
If you set to On, no sound outputs of all internal and external speakers.
➢
Rear of the TV
When the Audio out is set to Volume, you can select the Int.
mute and control it.
Coaxial
Analog
Optical
Sound
Mode
Custom
Bass
Treble
Ext. audio
Audio out
Volume
Int. mute
Off
Dolby Digital
Sound
EXT1
EXT2
S-video
Video
Analog
Analog
Analog
Analog
Sound
Mode
Custom
Bass
Treble
Ext. audio
Audio out
Volume
Int. mute
Off
Dolby Digital
Sound
Mode
Custom
Bass
Treble
Ext. audio
Audio out
Volume
Int. mute
On
Dolby Digital
English-25
apollo_en
12/23/02 5:25 PM
Page 26
Setting the Dolby Digital (LW40A13W)
You can enjoy Digital sound when the equipment with Digital output
is connected to the television.
Rear of the TV
1
Press the MENU button.
The main menu is displayed.
Result:
2
Press the P
or P
button to select the Sound.
The options available in the Sound group are displayed.
Result:
3
Press the
4
Press the P
or P
button to select the Dolby Digital.
+ button.
- or
Press the
The Dolby Digital menu is displayed with the
Result:
Pro Logic is selected.
5
Select the option (Auto, On or Off) by pressing the
+ button.
- or
Sound
Mode
Custom
Bass
Treble
Ext. audio
Audio out
Volume
Int. mute
Off
Dolby Digital
Sound
Pro Logic
:
Dynamic range :
Speaker set
➢
Sound
Pro Logic
:
Dynamic range :
Speaker set
On
On
Sound
Left
Test tone
On
Size :
Large
Volume:
0dB
Delay :
English-26
For further details of output depending on the each options,
refer to following page.
Press the P
or P
button to select the Dynamic range. If you
wish to adjust the volume properly during night viewing, select the On
+ button.
- or
by pressing the
7
Press the P
or P
button to select the Speaker setting.
+ button.
- or
Press the
The Speaker Setting menu is displayed with the main
Result:
left speaker is selected.
8
Select the speaker (Left, Center, Right, Right Rear, Left Rear,
Woofer) to be adjusted by pressing the P
or P
button.
9
Depending on the speaker, the following settings can be adjusted to
suit your personal preferences.
◆ Test tone to simulate the volume (On or Off)
◆ Size (Large, Small or Off)
◆ Volume level (-10dB ~ 10dB)
◆ delay time of surround channel (0 ~ 15ms) : When the Right
Rear or Left Rear is selected, you can adjust.
Sound
On
On
+ button.
6
On
Off
Pro Logic
:
Dynamic range :
Speaker set
- or
apollo_en
12/23/02 5:25 PM
Page 27
Setting the Dolby Pro Logic (LW40A13W)
In case of “Pro Logic : Auto”
Output
Input
(Source)
Main
Left
Center
Main
Right
Surround
Right
Left
Sub Woofer
Mono
✔
✔
PCM Stereo (L/R)
✔
✔
Mono
✔
✔
Lo/Ro
✔
✔
Lt/Rt
✔
✔
✔
✔
✔
5.1ch
✔
✔
✔
✔
✔
✔
DTS
✔
✔
✔
✔
✔
✔
MPEG I (Stereo only)
✔
MPEG I I
✔
✔
✔
✔
✔
✔
Main
Left
Center
Main
Right
Right
Left
✔
✔
✔
Dolby
Digital
✔
In case of “Pro Logic : On”
Output
Input
(Source)
Mono
Surround
Sub Woofer
✔
PCM Stereo (L/R)
✔
✔
✔
Mono
Lo/Ro
✔
✔
✔
✔
✔
Lt/Rt
✔
✔
✔
✔
✔
5.1ch
✔
✔
✔
✔
✔
✔
DTS
✔
✔
✔
✔
✔
✔
MPEG I (Stereo only)
✔
✔
✔
✔
✔
MPEG I I
✔
✔
✔
✔
✔
Main
Left
Center
Main
Right
Dolby
Digital
✔
In case of “Pro Logic : Off”
Output
Input
(Source)
Mono
✔
✔
Surround
Right
Left
Sub Woofer
✔
✔
Mono
✔
✔
Lo/Ro
✔
✔
Lt/Rt
✔
✔
5.1ch
✔
✔
✔
✔
✔
✔
DTS
✔
✔
✔
✔
✔
✔
MPEG I (Stereo only)
✔
MPEG I I
✔
✔
✔
✔
PCM Stereo (L/R)
Dolby
Digital
➣
✔
✔
✔
The output of Sub Woofer is changed depending on the speaker setting.
English-27
12/23/02 5:25 PM
Page 28
Selecting the Sound Mode
The “S.MODE” button displays/controls the processing and output of
the audio signal. When power is switched on, the mode is automatically
preset to either “Dual-I ” or “Stereo”, depending on the current
transmission.
On-screen indication
Regular broadcast
(Standard audio)
MONO (Normal use)
Regular +
NICAM Mono
MONO ↔ MONO
NICAM
(Normal)
NICAM Stereo
STEREO ↔ MONO
NICAM
(Normal)
NICAM Dual-I/II
Dual-I → Dual-I I→ MONO
NICAM NICAM (Normal)
A2
Stereo
Regular broadcast
(Standard audio)
MONO (Normal use)
Bilingual or Dual-I/II
DUAL-I ↔ DUAL-I I
Stereo
➣
→
NICAM
Stereo
Type of broadcast
→
apollo_en
STEREO ↔ MONO
(Forced mono)
◆ If the receiving conditions deteriorate, listening will be easier
if the mode is set to the MONO.
◆ If the stereo signal is weak and an automatic switching
occurs, then switch to the MONO.
◆ When receiving a mono sound in the AV mode, connect to
the “AUDIO (L)” input connector on the rear panel.
English-28
apollo_en
12/23/02 5:25 PM
Page 29
Viewing the Picture In Picture (PIP)
You can display a sub picture within the main picture of TV program or
external A/V devices such as VCR or DVD. In this way you can watch
TV program the video input from any connected devices while watching
TV or other video input.
1
Press the P
Result:
The main menu is displayed.
or P
Press the
4
Press the P
or P
- or
Press the
Result:
- or
+ button.
On
Video
Small
Main
- or
+ button.
You can also activate the PIP simply by pressing the PIP ON
button. To deactivate the PIP, press it again.
Result:
The sources are displayed in the following order
(depending on the model):
TV (LW40A13W) - Video - S-Video - EXT1 - EXT2.
7
:
The options available in the PIP group are displayed.
Press the P
or P
button to select the TV/Video. Select a
+ button.
- or
source of the sub picture by pressing the
➣
Function
PIP
TV/Video
Size
Locate
Swap
Sound sel
button to select the PIP.
+ button.
Select the On by pressing the
➣
6
button to select the Function.
The options available in the Function group are
displayed.
3
5
English
off
Press the MENU button.
Result:
2
Function
Time
PIP
Language
DNIe
Function
PIP
TV/Video
Size
Locate
Swap
Sound sel
:
On
Video
Small
Main
You can also select these options simply by pressing the
TV/VIDEO button.
Press the P
or P
button to select the Size. Select a size of
+ button.
- or
the sub picture by pressing the
Result:
The sizes are displayed in the following order:
Small - Double.
➣
You can also select these options simply by pressing the SIZE
button.
Function
PIP
TV/Video
Size
Locate
Swap
Sound sel
:
PIP
English-29
On
Video
Small
Main
apollo_en
12/23/02 5:25 PM
Page 30
Viewing the Picture In Picture (PIP)
Function
PIP
TV/Video
Size
Locate
Swap
Sound sel
:
On
Video
Small
Main
8
Press the P
or P
button to select the Locate. Move the sub
+ button.
picture counterclockwise by pressing the
➣
◆ When the size of sub picture is set to Double, this feature
does not work.
◆ You can also move the sub picture simply by pressing the
LOCATE button.
9
Press the P
Pressing the
Function
PIP
TV/Video
Size
Locate
Swap
Sound sel
:
Result:
On
Video
Small
Main
➣
10
or P
- or
button to select the Swap.
+ button.
The main picture and the sub picture are interchanged.
You can also select these options simply by pressing the
SWAP button.
Press the P
or P
button to select the Sound sel. To hear the
+
- or
sound of sub picture, select the Sub by pressing the
button.
Result:
The options are displayed in the following order:
Main - Sub.
Function
PIP
TV/Video
Size
Locate
Swap
Sound sel
:
PIP
English-30
On
Video
Small
Main
➣
◆ P▼/▲ button :
Used to select the channel of sub
picture.
◆ SCAN button :
Used to scan every memorized
channel in order. To stop scanning,
press it again.
apollo_en
12/23/02 5:25 PM
Page 31
Selecting the Sleep timer
You can select a time period of between 10 and 240 minutes after
your set automatically switches off.
1
Press the P
Result:
3
Press the
Result:
4
Press the
Result:
5
English
off
Press the MENU button.
Result:
2
Function
Time
PIP
Language
DNIe
The main menu is displayed.
or P
button to select the Function.
The options available in the Function group are
displayed.
- or
+ button.
The Time is selected.
- or
Function
Time Setting
Clock
On time
Off time
Sleep timer
+ button again.
The Time Setting menu is displayed.
Press the P
or P
button to select the Sleep timer. Select the
number of minutes after which your set switches off by pressing the
+ button repeatedly.
- or
◆ The preset time intervals: 10, 20, 30, 60, 90, 120, 150, 180, 210,
and 240 minutes.
PIP
➣
You can also select simply by pressing the “SLEEP” button.
If the sleep timer is already set, the screen displays the remaining
time and then your set will be switched off. If the sleep timer is not
yet set, displays Off.
English-31
09:37
06:00 On
23:30 On
Off
apollo_en
12/23/02 5:25 PM
Page 32
Setting and Displaying the Current Time
Function
Time
PIP
Language
DNIe
You can set the television’s clock so that the current time is display by
pressing the “DISPLAY” button. You must also set the time if you wish
switch the television on or off automatically at the time you select.
English
off
➣
1
09:35
24:00 Off
24:00 Off
Off
Press the MENU button.
Result:
Function
Time Setting
Clock
On time
Off time
Sleep timer
If you disconnect the power cord and re-connect it,
the clock will be reset to the default value.
2
Press the P
Result:
3
Press the
Result:
4
Press the
Result:
5
or P
button to select the Function.
The options available in the Function group are
displayed.
- or
+ button.
The Time is selected.
- or
+ button again.
The Time Setting menu is displayed with Clock
is selected.
+ button to move to the hour or minute.
- or
Press the
Set the hour or minute by pressing the P
or P
button.
➣
English-32
The main menu is displayed.
You can view the setting status of selected source by
pressing the “DISPLAY” button on the remote control.
apollo_en
12/23/02 5:25 PM
Page 33
Switching the Television On and Off Automatically
You can switch the television on or off automatically at the time you
select.
➣
1
The first step is to set the television’s clock (refer to “Setting
and Displaying the Current Time” on the previous page).
Function
Time
PIP
Language
DNIe
English
off
Press the MENU button.
Result:
The main menu is displayed.
Function
2
Press the P
Result:
3
Press the
Result:
4
Press the
or P
button to select the Function.
The options available in the Function group are
displayed.
- or
Time Setting
Clock
On time
Off time
Sleep timer
09:36
06:00 On
24:00 Off
Off
+ button.
The Time is selected.
- or
+ button again.
Function
Result:
5
The Time Setting menu is displayed.
Press the P
or P
button to select On time. Set the time at
which you wish the television to be switched on automatically.
+ button to move to the hour, minute or
- or
◆ Press the
on/off. Set these by pressing the P
or P
button.
6
Time Setting
Clock
On time
Off time
Sleep timer
Press the P
or P
button to select Off time.
In the same above, set the time at which you wish the television to
be switched off automatically.
English-33
09:37
06:00 On
23:30 On
Off
apollo_en
12/23/02 5:25 PM
Page 34
DNIe (Digital Natural Image engine)
Function
Time
PIP
Language
DNIe
English
off
Samsung’s New Technology bring you more detailed image with
contrast enhancement and white enhancement. New image
compensation algorithm gives brighter, cleare, to our customers.
DNIe technology will fit every signals into your eyes.
1
Press the MENU button.
Result:
2
Press the P
Result:
3
The main menu is displayed.
or P
button to select the Function.
The options available in the Function group are
displayed.
Press the P
or P
button to select the DNIe.
- or
Select the required option by pressing the the
repeatedly. The following options are available:
+ button
Off - Medium - High - Demo
English-34
◆ Off
Switches off the DNIe mode.
◆ Medium
Switches on the DNIe mode.
◆ High
The screen is more clear than in Medium.
◆ Demo
The screen before applying DNIe appears
on the right and the screen after applying
DNIe appears on the left.
apollo_en
12/23/02 5:25 PM
Page 35
Setting up Your PC Software (Based on Widows 2000 or XP)
The Windows display-settings for a typical computer are shown below. But the actual screens on your
PC will probably be different, depending upon your particular version of Windows and your particular
video card. But even if your actual screens look different, the same, basic set-up information will apply
in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer.)
1
First, click on “Settings” on the Windows start menu.
While “Settings” is highlighted, move the cursor so
that “Control Panel” is highlighted.
2
When the control panel screen appears,
click on “Display” and a display dialogbox will appear.
3
Navigate to the “Settings” tab on the display dialog-box.
The correct setting of size (resolution)
- 1280 x 768 pixels
If a vertical-frequency option exists on your display settings
dialog box, the correct value is “60” or “60 Hz”.
Otherwise, just click “OK” and exit the dialog box.
English-35
apollo_en
12/23/02 5:25 PM
Page 36
Adjusting the Contrast and Brightness
➣
Preset to the PC mode by pressing the VIDEO button.
PC
Image
Image lock
Position
Colour adjust
Recall
Auto adjustment
1024x768 48.2kHz 59.9Hz
1
Result:
2
Press the
Result:
PC
4
Press the
Result:
Expand 1
The main menu is displayed.
Press the P
Result:
3
Image
Contrast
Brightness
Size
Press the MENU button.
or P
button to select the PC.
The options available in the PC group are displayed.
- or
+ button.
The Image is selected.
- or
+ button again.
The options available in the Image group are displayed.
5
Select the option (Contrast or Brightness) to be adjusted for the
colour of your computer image by pressing the P
or P
button.
+ button.
- or
Press the
Result:
The horizontal bar is displayed.
In Digital mode, the Brightness can be only adjusted.
6
Press the
Contrast
75
- or
+ button to reach the required setting.
Selecting the Image Size
➣
Preset to the PC mode by pressing the VIDEO button.
This function doesn’t work in Digital input.
PC
Image
Contrast
Brightness
Size
1
Press the MENU button.
Result:
Expand 1
2
Press the P
Result:
3
Press the
Result:
4
Press the
Result:
5
or P
button to select the PC.
The options available in the PC group are displayed.
- or
+ button.
The Image is selected.
- or
+ button again.
The options available in the Image group are displayed.
Press the P
or P
button to select the Size. Select a size of
+ button.
- or
the your computer image by pressing the
Result:
➣
English-36
The main menu is displayed.
The sizes are displayed in the following order:
Expand 1 - Expand 2 - Normal.
You can also select these options simply by pressing the
P.SIZE (Picture Size) button.
apollo_en
12/23/02 5:25 PM
Page 37
Adjusting the Image Quality
➣
Preset to the PC mode by pressing the VIDEO button.
This function doesn’t work in Digital input.
This feature is used to fine tune and get the best image by removing
noises that create unstable images with jitters and shimmers.
1
Press the MENU button.
Result:
2
Press the P
Result:
The main menu is displayed.
or P
The options available in the PC group are displayed.
3
Press the
4
Press the P
or P
- or
Press the
Result:
5
- or
+ button.
button to select the Image lock.
+ button.
Press the
➣
PC
Image lock
Coarse
Fine
The options available in the Image lock group are
displayed.
Select the option (Coarse or Fine) to be adjusted for the quality of
your computer image by pressing the P
or P
button.
+ button.
- or
Press the
Result:
6
button to select the PC.
PC
Image
Image lock
Position
Colour adjust
Recall
Auto adjustment
1024x768 48.2kHz 59.9Hz
Coarse
1344
The horizontal bar is displayed.
- or
+ button to reach the required setting.
This feature may change the width of the image. If necessary, adjust
the position to center.
Changing the Image Position
➣
1
Preset to the PC mode by pressing the VIDEO button.
This function doesn’t work in Digital input.
PC
Press the MENU button.
Result:
2
Press the P
Result:
The main menu is displayed.
or P
The options available in the PC group are displayed.
3
Press the
4
Press the P
or P
- or
Press the
5
- or
+ button.
button to select the Position.
+ button.
Select the position (H-Position or V-Position) to be adjusted by
+ button.
- or
pressing the P
or P
button. Press the
Result:
6
button to select the PC.
Press the
Image
Image lock
Position
Colour adjust
Recall
Auto adjustment
1024x768 48.2kHz 59.9Hz
PC
Position
H-Position
V-Position
The horizontal bar is displayed.
- or
+ button to reach the required setting.
H-Position
50
English-37
apollo_en
12/23/02 5:25 PM
Page 38
Adjusting the Colour
➣
Preset to the PC mode by pressing the VIDEO button.
This function doesn’t work in Digital input.
PC
Image
Image lock
Position
Colour adjust
Recall
Auto adjustment
1024x768 48.2kHz 59.9Hz
PC
Mode
R
G
B
Press the MENU button.
Result:
2
Press the P
Result:
Press the P
or P
- or
Press the
- or
+ button.
button to select the Colour adjust.
+ button.
The options available in the Colour adjust group are
displayed with the Mode is selected.
+
5
- or
Select the required colour mode by pressing the
button repeatedly. the following colour modes are available.
Custom - Colour 1 - Colour 2 - Colour 3
6
If you wish adjust the colour which best corresponds to you viewing
requirements, select the option (R-Red, G-Green or B-Blue) to be
adjusted by pressing the P
or P
button.
+ button.
- or
Press the
Result:
7
➣
English-38
button to select the PC.
The options available in the PC group are displayed.
4
Custom
100
or P
Press the
Result:
R
The main menu is displayed.
3
Custom
PC
Mode
R
G
B
1
Press the
The horizontal bar is displayed.
- or
+ button to reach the required setting.
If you change the R(Red) G(Green)or B(Blue) setting, the Mode is
selected to Custom automatically.
apollo_en
12/23/02 5:25 PM
Page 39
Initializing the Image Settings
➣
Preset to the PC mode by pressing the VIDEO button.
You can replace all image settings with the factory default values.
1
Press the MENU button.
Result:
2
Press the P
Result:
3
4
Press the
or P
button to select the PC.
The options available in the PC group are displayed.
- or
Press the P
or P
- or
Press the
Result:
5
The main menu is displayed.
PC
Image
Image lock
Position
Colour adjust
Recall
Auto adjustment
1024x768 48.2kHz 59.9Hz
+ button.
button to select the Recall.
+ button.
PC
Recall
Image recall
Colour recall
The options available in the Recall group are displayed.
Select the option (Image recall or Colour recall) to be replaced
+ button.
- or
by pressing the P
or P
button. Press the
Result:
The screen becomes black and return to original view
about a few seconds later.
In Digital input, the Colour recall can be only adjusted.
Adjusting the PC Screen Automatically
➣
Preset to the PC mode by pressing the VIDEO button.
This function doesn’t work in Digital input.
PC
1
Press the MENU button.
Result:
2
Press the P
Result:
The main menu is displayed.
or P
The options available in the PC group are displayed.
3
Press the
4
Press the P
or P
- or
Press the
Result:
button to select the PC.
- or
Image
Image lock
Position
Colour adjust
Recall
Auto adjustment
1024x768 48.2kHz 59.9Hz
+ button.
button to select the Auto adjustment.
+ button.
Auto adjustment
Please wait
The screen quality and position are automatically adjusted,
and the screen returns to original view about a few seconds
later.
English-39
apollo_en
12/23/02 5:25 PM
Page 40
Teletext Feature
Most television channels provide written information services via
teletext. Information provided includes:
◆ Television programme times
◆ News bulletins and weather forecasts
◆ Sports results
◆ Travel information
This information is divided into numbered pages (see diagram).
Part
Contents
A
Selected page number.
B
Broadcasting channel identity.
C
Current page number or search indications.
D
Date and time.
E
Text.
F
Status information.
FASTEXT information.
➣
Teletext information is often divided between several pages
displayed in sequence, which can be accessed by:
◆ Entering the page number
◆ Selecting a title in a list
◆ Selecting a coloured heading (FASTEXT system)
English-40
apollo_en
12/23/02 5:25 PM
Page 41
Displaying the Teletext Information
You can display Teletext information at any time on your set.
☛
For Teletext information to be displayed correctly, channel
reception must be stable; otherwise:
◆ Information may be missing
◆ Some pages may not be displayed
1
Select the channel providing the Teletext service by pressing
the P
or P
button.
2
Press the TTX/MIX button to activate the teletext mode.
Result:
The contents page is displayed. It can be redisplayed at
any time by pressing the
(index) button.
3
Press the TTX/MIX button again.
Result:
The screen will be split into two. This Double Teletext
feature lets you view the actual broadcast and teletext
information separately on the screen.
4
If you wish to display the actual broadcast and teletext information on
a single screen, press the TTX/MIX button again.
5
Press the TV button again to exit from the teletext display.
Selecting Display Options
When you have displayed a Teletext page, you can select various
options to suit your requirements.
To display...
Press the...
◆ Both teletext information and
the normal broadcast
TTX/MIX twice
◆ Hidden text
(answers to quiz games, for example)
(reveal)
◆ The normal screen
(reveal) again
◆ A secondary page,
by entering its 4-digit number
◆ Double-size letters in the:
• Upper half of the screen
• Lower half of the screen
• Once
• Twice
◆ Normal screen
• Three times
English-41
apollo_en
12/23/02 5:25 PM
Page 42
Selecting a Teletext Page
The various topics included in the teletext pages are colour-coded,
and can be selected by pressing the coloured buttons on the remote
control.
1
Enter the three-digit page number given in the content by pressing
the corresponding numeric buttons.
Result:
English-42
The current page counter is incremented and the page is
then displayed.
2
If the FASTEXT system is used by the broadcasting company, the
different topics covered on a Teletext page are colour-coded and can
be selected by pressing the coloured buttons on the remote control.
Press the coloured button corresponding to the topic that you wish to
select; the available topics are given on the status line.
Result:
The page is displayed with other colored information that
can be selected in the same way.
3
To display the previous or next page, press the corresponding
coloured button.
4
To display the subpage, press the
button.
The available subpages appear.
Result:
apollo_en
12/23/02 5:25 PM
Page 43
Troubleshooting: Before Contacting Service Personnel
Before contacting Samsung after-sales service, perform the following simple checks.
If you cannot solve the problem using the instructions below, note the model and serial number of your
set and contact your local dealer.
No sound or picture
◆
◆
◆
◆
Normal picture but no sound
◆ Check the volume.
◆ Check whether the MUTE button has been pressed on the remote
control.
No picture or black and white picture
◆ Adjust the colour settings.
◆ Check that the broadcast system selected is correct.
Sound and picture interference
◆ Try to identify the electrical appliance that is affecting the set and
move it further away.
◆ Plug your set into a different mains socket.
Blurred or snowy picture,
distorted sound
◆ Check the direction, location and connections of your aerial.
This interference is often due to the use of an indoor aerial.
Remote control malfunctions
◆ Replace the remote control batteries.
◆ Clean the upper edge of the remote control (transmission window).
◆ Check the battery terminals.
“Check Signal Cable” message is
displayed.
◆ Check that the signal cable is firmly connected to the PC or video
sources.
◆ Check that the PC or video sources are turned on.
On PC mode, “Not Supported Mode”
message is displayed.
◆ Check the maximum resolution and the frequency of the video
Adapter.
◆ Compare these values with the data in the Display Modes Timing
Chart.
On PC mode, horizontal or vertical bars
appear to flicker, jitter or shimmer on the
image.
◆ Adjust the Coarse or Fine function.
On PC mode, screen is black and
power indicator light is steady amber
or blinks every 0.5 or 1 seconds
◆ The TV is using its power management system.
◆ Move the computer’s mouse or press a key on the keyboard.
On PC mode, image is not stable and
may appear to vibrate.
◆ Check that the display resolution and frequency from your
computer or video board is an available mode for your set. On your
computer check: Control Panel, Display, Settings.
◆ If the setting is not correct, use your computer utility programme to
change the display settings.
Check that the mains lead has been connected to a wall socket.
Check that you have pressed the POWER (
) button.
Check the picture contrast and brightness settings.
Check the volume.
➣
Your set supports multiscan display functions within the
following frequency domain:
Horizontal frequency: 30 ~ 60 kHz
Vertical frequency: 56 ~ 75 Hz
On PC mode, image is not centered
on the screen.
◆ Adjust the horizontal and vertical position.
You need the Monitor driver software.
◆ Download the driver from WWW pages:
http://www.samsung-monitor.com
English-43
apollo_en
12/23/02 5:25 PM
Page 44
PowerSaver
This set has a built-in power management system called PowerSaver. This system saves energy by
switching your set into a low-power mode when it has not been used for a certain period of time.
The available modes are “On”, “Standby”, “Sleep”, and “Deep Sleep”. PowerSaver operates with a
VESA DPMS compliant video card installed in your computer. You use a software utility installed on
your computer to set up this feature.
Normal Operation
Power-Saving Function mode
(EPA/NUTEK)
Horizontal Sync
Active
Inactive
Vertical Sync
Active
Inactive
Power Indicator
Green
Green, Blinking (1 sec interval)
LW29A13W : 150W (Max.)
LW40A13W : 230W (Max.)
Less than 8W
State
Power Consumption
➣
This set automatically returns to normal operation when horizontal and vertical sync return.
This occurs when you move the computer’s mouse or press a key on the keyboard.
English-44
apollo_en
12/23/02 5:25 PM
Page 45
Technical and Environmental Specifications
Model
LW29A13W
LW40A13W
Panel
Size
Display Size
Type
Pixel Pitch
Viewing Angle
29” Diagonal
39.6” Diagonal
631.68 (H) x 397.01 (V) mm
862.08 (H) x 517.24 (V) mm
a-si TFT active matrix
0.4935 (H) x 0.4935 (V) mm
0.6735 (H) x 0.6735 (V) mm
85/85/85/85 (L/R/T/B)
Frequency
Horizontal
Vertical
Display Colour
30 ~ 60 kHz
56 ~ 75 Hz
16,777,216 colours
Display Resolution
Maximum Mode
1280 x 768 @ 60 Hz
Input Signal
Sync.
Video Signal
H/V Separate, TTL, P. or N.
0.7 Vp-p @ 75 ohm
TV/Video
Colour System
Sound System
Video Format
PAL, SECAM, NTSC4.43
B/G, D/K, I, L,
CVBS, S-VHS
Ext
Video Input/Output
RGB Input
Audio Input/Output
1.0 Vp-p @ 75 ohm
0.7 Vp-p @ 75 ohm
500mVrms
Colour system
PAL
Power Supply
Input
Output
200 - 240 V~ (50/60Hz)
DC 28V/8A
Power Consumption
Maximum
Power Saving
150W
230 W
8W
Dimension (W x H x D) / Weight
Set
759.6 x 568.5 x 195 mm, 13.7 kg
Speaker L/R
570.5 x 130 x 155 mm, 2.4 kg
Wall/Mount-kit(option)
727 x 400 x 94 mm, 4.9 kg
Stand
-
1006 x 713 x 58 mm, 21.5 kg
744 x 170 x 230 mm, 4.9 kg
960 x 400 x 94 mm, 5.7 kg
956 x 33.4 x 300 mm, 5.6 kg
Environmental Considerations
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
10 °C to 40 °C (50 °F to 104 °F)
10% to 80%
-25 °C to 45 °C (- 13 °F to 113 °F)
5% to 95%
English-45
apollo_en
12/23/02 5:25 PM
Page 46
Technical and Environmental Specifications
Model
LW29A13W
LW40A13W
Audio Characteristics
Audio Input
Audio Input (PC)
Audio Output
Speaker Output
Headphone Output
Frequency
Response
RCA Jack (L, R), 0.5Vrms (-9dB)
3.5Ø Stereo Jack, 0.5Vrms (-9dB)
RCA Jack (L, R), 0.5Vrms (-9dB)
Max. 10W Output (3.5Ø Stereo Jack, 8Ω)
Max. 10mW Output (3.5Ø Stereo Jack, 32Ω)
RF: 80Hz ~ 15kHz (at- 3dB)
A/V: 80Hz ~ 20kHz (at- 3dB)
Display Modes
If the signal from the system equals to the standard signal mode, the screen is adjusted automatically.
If the signal from the system doesn’t equal to the standard signal mode, adjust the mode with referring
to the Video card user guide because the screen might not display or only the power LED might be on.
For the display modes listed below, the screen image has been optimized during manufacture.
Mode
Resolution
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
Pixel Clock
Frequency (MHz)
Sync Polarity
(H/V)
IBM
640 x 480
640 x 480
31.469
35.000
59.940
66.667
25.175
30.240
-/-/-
VESA
640 x 480
640 x 480
37.861
37.500
72.809
75.000
31.500
31.500
-/-/-
IBM
720 x 400
31.469
70.087
28.322
-/+
VESA
800 x 600
800 x 600
800 x 600
37.879
48.077
46.875
60.317
72.188
75.000
40.000
50.000
49.500
+/+
+/+
+/+
IBM
832 x 624
49.726
74.551
57.284
-/-
VESA
1024 x 768
1024 x 768
1024 x 768
48.363
56.476
60.023
60.004
70.069
75.029
65.000
75.000
78.750
-/-/+/+
GTF
1280 x 768
47.700
60.000
80.136
-/-
English-46
apollo_en
12/23/02 5:25 PM
Page 47
Wiring the Mains Power Supply Plug (UK Only)
◆ IMPORTANT NOTICE
The mains lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse
is indicated on the pin face of the plug and, if it requires replacing, a fuse approved to BSI1362 of the same
rating must be used. Never use the plug with the fuse cover omitted if the cover is detachable.
If a replacement fuse cover is required, it must be of the same colour as the pin face of the plug. Replacement
covers are available from your dealer. If the fitted plug is not suitable for the power points in your house or the
cable is not long enough to reach a power point, you should obtain a suitable safety approved extension lead
or consult your dealer for assistance. However, if there is no alternative to cutting off the plug, remove the fuse
and then safely dispose of the plug. Do NOT connect the plug to a mains socket as there is a risk of shock
hazard from the bared flexible cord.
◆ IMPORTANT
The wires in the mains lead are coloured in accordance with the following code:
BLUE - NEUTRAL
BROWN - LIVE
As these colours may not correspond to the coloured markings identifying the terminals in your plug,
proceed as follows:
The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or
BLACK. The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured
BROWN or RED.
WARNING:
DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL, WHICH IS MARKED
WITH THE LETTER E OR BY THE EARTH SYMBOL , OR COLOURED GREEN OR
GREEN AND YELLOW.
English-47
apollo_en
12/23/02 5:25 PM
Memo
English-48
Page 48
apollo_en
12/23/02 5:25 PM
Page 49
Memo
English-49
apollo_en
12/23/02 5:25 PM
Page 50
- AFTER SALES SERVICE
- Do not hesitate to contact your retailer or service agent if a
change in the performance of your product indicates that a
faulty condition may be present.
ELECTRONICS
Download PDF

advertising