Samsung | CL-21A11MQ | Samsung CL-21A11MQ Manual de Usuario

AA68-02647A-00 (ENG)
Owner’s
Instructions
.............
COLOR TELEVISION
.............................................................................................................................
CL21M6W
CL21M5W
Warning! Important
Safety Instructions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol indicates high voltage is present inside. It is
dangerous to make any kind of contact with any inside part of
this product.
This symbol alerts you that important literature concerning
operation and maintenance has been included with this product.
Note to CATV system installer: This reminder is provided to call CATV system
installer’s attention to Article 820-40 of the National Electrical Code (Section 54 of
Canadian Electrical Code, Part I), that provides guidelines for proper grounding
and, in particular, specifies that the cable ground shall be connected to the
grounding system of the building as close to the point of cable entry as practical.
Important: One Federal Court has held that unauthorized recording of
copyrighted TV programs is an infringement of U.S. copyright laws.
Certain Canadian programs may also be copyrighted and any unauthorized
recording in whole or in part may be in violation of these rights.
To prevent damage which may result in fire or electric shock
hazard, do not expose this appliance to rain or moisture.
Thank You for Choosing Samsung
Thank you for choosing Samsung! Your new Samsung TV receiver represents the latest in
television technology. It has easy-to-use, on-screen menus and closed-captioning capabilities,
making this TV one of the best products in its class. This product will provide convenient,
dependable service and enjoyment for years to come.
Important Safety Information
To reduce the risk of fire, electrical shock, and other injuries, keep these safety precautions in
mind when installing, using, and maintaining your machine.
• Read all safety and operating instructions before operating the TV receiver.
• Retain the safety and operating instructions for future reference.
• Heed all warnings on the TV receiver and in the operating instructions.
• Follow all operating instructions.
• Unplug the TV receiver from the wall outlet before cleaning, Use a damp cloth, Do not use
liquid or aerosol cleaners.
• Never add any attachments and/or equipment without approval of the manufacturer. Such
additions may cause risk of fire, electric shock, or other personal injury.
• Do not use the TV receiver where contact with or immersion in water is a possibility, such as
near bath tubs, sinks, washing machines, swimming pools, etc.
• Do not place the TV receiver on an unstable cart, stand, tripod,
bracket, or table. The TV receiver may fall, causing injury to
people and/or damage to the TV. Use only with a cart, stand,
tripod, bracket, or table recommended by the manufacturer or
sold with the TV receiver.
• Follow the manufacturer’s instructions when mounting the unit,
and use a mounting accessory recommended by the manufacturer.
Move the TV receiver and its cart with care. Quick stops, excessive
force, and uneven surfaces may cause the unit and cart to overturn.
• Provide ventilation for the TV receiver. The unit is designed with slots in the cabinet for
ventilation to protect it from overheating. Do not block these openings with any object, and
do not place the TV receiver on a bed, sofa, rug, or other similar surface. Do not place it near
a radiator or heat register. If you place the TV receiver on a rack or bookcase, ensure that
there is adequate ventilation and that you’ve followed the manufacturer’s instructions for
mounting.
• Operate your TV receiver only from the type of power source indicated on the marking label.
If you are not sure of the type of power supplied to your home, consult your appliance dealer
or local power company.
• Use only a grounded or polarized outlet. For your safety, this TV is equipped with a polarized
alternating-current line plug having one blade wider than the other. This plug will fit into the
power outlet only one way. If you are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug still does not fit, contact your electrician to replace your outlet.
SAFETY
1
• Protect the power cord. Power supply cords should be routed so that they will not be walked
on or pinched by items placed on or against them. Pay particular attention to cord placement
at plugs, convenience receptacles, and at the point where they exit from the unit.
• Unplug the TV receiver from the wall outlet and disconnect the antenna or cable system during a lightning storm or when left unattended and unused for long periods of time. This will
prevent damage to the unit due to lightning and power-line surges.
• An outside antenna system should not be placed in the vicinity of overhead power lines or
other electric light or power circuits or where it can fall into such power lines or circuits.
Avoid overhead power lines: When installing an outside antenna system, be extremely careful
to keep from touching the power lines or circuits. Contact with such lines might be fatal.
• Do not overload the wall outlet or extension cords. Overloading can result in fire or electric
shock.
• Do not insert foreign objects through openings in the unit, as they may touch dangerous
voltages or cause damage. Never spill liquid of any kind on the TV receiver.
• Ground outdoor antennas. If an outside antenna or cable
system is connected to the TV receiver, be sure the
antenna or cable system is grounded so as to provide
some protection against voltage surges and built-up static
charges. Read information with respect to proper
grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna
discharge unit, size of grounding conductors, location of
antenna-discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
EXAMPLE OF
ANTENNA GROUNDING
ANTENNA
LEAD IN WIRE
GROUND CLAMP
ANTENNA
DISCHARGE UNIT
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING
CONDUCTORS
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
• Do not attempt to service the TV receiver yourself. Refer all servicing to qualified service
personnel. Unplug the unit from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
- When the power-supply cord or plug is damaged
- If liquid has been spilled on the unit or if objects have fallen into the TV
- If the TV receiver has been exposed to rain or water
- If the TV receiver does not operate normally by following the operating instructions
- If the TV receiver has been dropped or the cabinet has been damaged
- When the TV receiver exhibits a distinct degradation in performance
• If you make adjustments yourself, adjust only those controls that are covered by the operating instructions. Adjusting other controls may result in damage and will often require extensive work by a qualified technician to restore the TV receiver to normal.
• When replacement parts are required, be sure the service technician uses replacement parts
specified by the manufacturer or those that have the same characteristics as the original part.
Unauthorized substitutions may result in additional damage to the unit.
• Upon completion of any service or repairs to this TV receiver, ask the service technician to
perform safety checks to determine that the TV receiver is in a safe operating condition.
2 SAFETY
CONTENTS
Chapter 1: Your New TV . . . . . . . . . . . . . . .1.1
List of Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1
Familiarizing Yourself with The TV. . . . . . . . . . . . . . . . . . . . . . . . . . 1.2
Front Panel Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2
Side Panel Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3
Rear Panel Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5
Chapter 2: Installation . . . . . . . . . . . . . . . . 2.1
Connecting VHF and UHF Antennas . . . . . . . . . . . . . . . . . . . . . . . . 2.1
Antennas with 300-ohm Flat Twin Leads . . . . . . . . . . . . . . 2.1
Antennas with 75-ohm Round Leads . . . . . . . . . . . . . . . . . 2.2
Separate VHF and UHF Antennas. . . . . . . . . . . . . . . . . . . . 2.2
Connecting Cable TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2
Cable without a Cable Box . . . . . . . . . . . . . . . . . . . . . . . . . 2.2
Connecting to a Cable Box that Descrambles
All Channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3
Connecting to a Cable Box that Descrambles
Some Channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3
Connecting a VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4
Connecting a Second VCR to Record from the TV . . . . . . . 2.6
Connecting a DVD Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6
Connecting a Camcorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7
Installing Batteries in the Remote Control. . . . . . . . . . . . . . . . . . . . . 2.8
Chapter 3: Operation . . . . . . . . . . . . . . . . . . 3.1
Turning the TV On and Off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.1
Plug & Play Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.1
Viewing the Menus and On-Screen Displays. . . . . . . . . . . . . . . . . . . 3.3
Viewing the Menus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3
Viewing the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3
Selecting a Menu Language. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.4
Memorizing the Channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5
Selecting the Video Signal-source . . . . . . . . . . . . . . . . . . . . 3.5
Storing Channels in Memory (Automatic Method) . . . . . . . 3.6
Adding and Erasing Channels (Manual Method) . . . . . . . . 3.7
Changing Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.8
Using the Channel Buttons. . . . . . . . . . . . . . . . . . . . . . . . . 3.8
Directly Accessing Channels. . . . . . . . . . . . . . . . . . . . . . . . 3.8
Using the PRE-CH Button to select the Previous Channel. . 3.8
CONTENTS
1
CONTENTS
Chapter 3: Operation (Cont...) . . . . . . . . . . 3.8
Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.8
Using Mute. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.8
Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.9
Customizing the Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.10
Using Automatic Picture Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.11
Customizing the Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.12
Using Automatic Sound Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.13
Setting The On/Off Melody. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.14
Viewing a VCR or Camcorder Tape. . . . . . . . . . . . . . . . . . . . . . . . . . 3.15
Chapter 4: Special Features . . . . . . . . . . . . 4.1
Customizing Your Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1
Setting Up Your Remote Control to Operate Your VCR. . . . 4.1
Setting Up Your Remote Control to Operate Your Cable Box. . 4.3
Fine Tuning Channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4
Changing the Screen Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5
Digital Noise Reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.6
Using the Surf Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.7
Setting the On/Off Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.8
Setting the Sleep Timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.9
Sound Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.10
Choosing a Multi-Channel Sound (MTS) Soundtrack. . . . . 4.10
Extra Sound Settings
(Turbo Sound, Surround, or Auto Volume) . . . . . . . . . . . . 4.11
Viewing Closed Captions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.12
Viewing the Demonstration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.13
Chapter 5: Troubleshooting . . . . . . . . . . . . 5.1
Identifying Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.1
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . A.1
Cleaning and Maintaining Your TV. . . . . . . . . . . . . . . . . . . . . . . . . . A.1
Using Your TV in Another Country . . . . . . . . . . . . . . . . . . . . . . . . . A.1
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.1
2
CONTENTS
Chapter One
YOUR NEW TV
List of Features
Your TV was designed with the latest technology. This TV is a high-performance unit that
includes the following special features:
• Easy-to-use remote control
• Easy-to-use on-screen menu system
• Automatic timer to turn the TV on and off
• Adjustable picture and sound settings that can be stored in the TV’s memory
• Automatic channel tuning for up to 181 channels
• A special filter to reduce or eliminate reception problems
• Fine tuning control for the sharpest picture possible
• Built-in, dual channel speakers
• A special sleep timer
CHAPTER ONE: YOUR NEW TV
1.1
YOUR NEW TV
Familiarizing Yourself with The TV
Front Panel Buttons
The buttons on the front panel control your TV’s basic features, including the on-screen
menu. To use the more advanced features, you must use the remote control.
ΠMENU
Press to see an on-screen menu of your TV's features.
´ VOL – , +
Press to increase or decrease the volume.
Also used to select items on the on-screen menu.
ˇ CH ▼ and CH ▲
Press to change channels. Also press to select
various items on the on-screen menu.
1.2
CHAPTER ONE: YOUR NEW TV
¨ Remote Control Sensor
Aim the remote control towards this spot on the
TV.
ˆ STAND BY indicator
Lights up when you turn the power off.
Ø POWER
Press to turn the TV on and off.
YOUR NEW TV
Side Panel Jacks
You can use the Side panel jacks to connect an A/V component that is used only occasionally, such as a camcorder or video game. (For information on connecting equipment,
see pages 2.1 – 2.7.)
ΠAUDIO INPUTS
Audio signals from VCRs, DVD players and similar devices.
´ VIDEO INPUT
Video signals from VCRs, DVD players and similar devices.
ˇ HEADPHONE
Connect a set of external headphones to this jack for private listening.
CHAPTER ONE: YOUR NEW TV
1.3
YOUR NEW TV
Rear Panel Jacks
Use the rear panel jacks to connect an A/V component that will be connected
continuously, such as a VCR or a DVD player.
Because there are two sets of input jacks, you can connect two different A/V
components (i.e., a VCR and a DVD, 2 VCRs, etc.)
For more information on connecting equipment, see pages 2.1 – 2.7.
ΠAUDIO-VIDEO MONITOR
OUTPUTS
These audio-video signals are identical to A/V
signals being displayed on the big screen.
(Typically used as the input signals for a recording VCR.)
¨ DVD AUDIO INPUTS
(INPUT 2)
Use these jacks to connect the audio signals
from a DVD player when using the DVD video
input jacks. When not using the DVD jacks, these
audio jacks function as audio for Video 2.
ˆ DVD VIDEO INPUT
´ VIDEO INPUT
Video signals from VCRs, DVD players and similar
devices.
ˇ AUDIO INPUTS
Audio signals from VCRs, DVD players and similar
devices.
1.4
CHAPTER ONE: YOUR NEW TV
Connect video from a DVD player.
Note: Monitor Output doesn’t operate in the DVD
mode.
Ø VHF/UHF
Connect to an antenna or to a cable TV system.
YOUR NEW TV
Remote Control
You can use the remote control up to about 23 feet from the TV. When using the remote,
always point it directly at the TV.
You can also use your remote control to operate your VCR and cable box. See page 4.1
for details.
ΠPOWER
˝ TV
Turns the TV on and off.
Press to use your remote control
to operate your TV.
´ Number buttons
VCR
Press to select channels directly
on the TV.
Press to use your remote control
to operate your VCR.
+100
CABLE
Press to select channels over 100.
For example, to select channel
121, press “+100”, then press “2”
and “1”.
Press to use your remote control
to operate a cable box.
SET
ˇ P.SIZE
Use this button when you are setting up your remote control to
operate your VCR or cable box.
Press to change the screen size.
Your choices are Normal screen
or Zoom screen.
Ô PRE-CH
¨ R.SURF
Tunes to the previous channel.
Press the R.SURF button to automatically return to a preferred
channel after a user-preset time
delay.
 MTS (Multichannel
Television Stereo)
Press to choose stereo, mono or
Separate Audio Program (SAP
broadcast).
ˆ SLEEP
Press to select a preset time interval for automatic shutoff.
Ò DISPLAY
Press to see the time, channel,
etc., on-screen. Also press to exit
(quit) the menu system.
Ø TURBO
Press to turn the TURBO sound On
or Off.
Ú VOL -, VOL
∏ MUTE
+
Press to increase or decrease the
volume. (Also used to make selections on the on-screen menus.)
Press to temporarily cut off
the sound.
” CH▲ and CH▼
(Channel Up/Down)
Æ MENU
Displays the main on-screen
menu.
Press CH▲ or CH▼ to change
channels. (Also used to highlight
selections on the on-screen
menus.)
ı TV/VIDEO
Press to display all of the
available video sources
(i.e., Antenna/cable, VCR).
’ P.STD
Adjust the TV picture by selecting
one of the preset factory settings
(or select your personal, customized picture settings).
CL21M6W
CHAPTER ONE: YOUR NEW TV
1.5
YOUR NEW TV
Remote Control
˜ VCR Controls
¯ PIP Controls
(Not available)
• REW (Rewind)
Press to rewind a tape in your
VCR.
SWAP
Exchanges the video signal that is
currently displayed on the main
screen with the signal in the PIP
window.
• STOP
Press this button to stop a tape
during play, record, rewind or
fast forward. If the button is
pressed during Full-Automatic
play, the function will be cancelled.
TV/VIDEO
Press to select one of the available
signal sources for the PIP window.
• PLAY
PIP/SIZE
Press this button to control the PIP
window. Press repeatedly to cycle
through this sequence: PIP ON
with large window, PIP ON with
small window, and PIP OFF.
Press the PLAY button to play
back prerecorded tapes.
• F.F
Press to fast forward the tape in
your VCR.
• PAUSE
CH
Not available.
Press to pause your VCR’s tape.
CL21M6W
1.6
CHAPTER ONE: YOUR NEW TV
YOUR NEW TV
Remote Control
You can use the remote control up to about 23 feet from the TV. When using the remote,
always point it directly at the TV.
ΠPOWER
Ø TV/VIDEO
Turns the TV on and off.
Press to display all of the
available video sources (i.e.,
Antenna/cable, VCR
´ Number buttons
Press to select channels directly
on the TV.
∏ SURF
Press the SURF button to automatically return to a preferred channel
after a user-preset time delay.
ˇ +100
Press to select channels over 100.
For example, to select
channel 121, press “+100,” then
press “2” and “1.”
” SLEEP
Press to select a preset time interval for automatic shutoff.
¨ MUTE
’ MTS (Multichannel
Television Stereo)
Press to temporarily cut off
the sound.
Press to choose stereo, mono or
Separate Audio Program (SAP
broadcast).
ˆ CH▲ and CH▼
(Channel Up/Down)
Press CH▲ or CH▼ to change
channels. (Also used to highlight
selections on the on-screen
menus.)
˝ PRE-CH
Tunes to the previous channel.
Ô DISPLAY
Press to see the time, channel,
etc., on-screen. Also press to exit
(quit) the menu system.
 VOL -, VOL
+
Press increase or decrease the
volume. (Also used to make selections on the on-screen menus.)
Ò MENU
Displays the main on-screen
menu.
CL21M5W
CHAPTER ONE: YOUR NEW TV
1.7
2
C h a p t e r Tw o
I N S TA L L AT I O N
Connecting VHF and UHF Antennas
If your antenna has a set of leads that
look like this, see “Antennas with
300-ohm Flat Twin Leads” below.
If your antenna has one lead that looks
like this, see “Antennas with 75-ohm
Round Leads” on page 2.2.
If you have two antennas, see “Separate
VHF and UHF Antennas” on page 2.2.
Antennas with 300-ohm Flat Twin Leads
If you are using an off-air antenna (such as a roof antenna or “rabbit ears”) that has
300-ohm twin flat leads, follow the directions below.
1
Place the wires from the
twin leads under the
screws on the 300-75 ohm
adaptor (not supplied).
Use a screwdriver to
tighten the screws.
2
Plug the adaptor into the
VHF/UHF terminal on the
bottom of the back panel.
2.1
CHAPTER TWO: INSTALLATION
I N S TA L L AT I O N
Antennas with 75-ohm Round Leads
1
Plug the antenna lead into
the VHF/UHF
terminal on the bottom of
the back panel.
Separate VHF and UHF Antennas
If you have two separate antennas for your TV (one VHF and one UHF), you must
combine the two antenna signals before connecting the antennas to the TV. This
procedure requires an optional combiner-adaptor (available at most electronics shops).
1
Connect both antenna
leads to the combiner.
2
Plug the combiner into the
VHF/UHF terminal on the
bottom of the rear panel.
Connecting Cable TV
To connect to a cable TV system, follow the instructions below.
Cable without a Cable Box
Plug the incoming cable
into the VHF/UHF antenna
terminal on back of the TV.
Because this TV is cable-ready,
you do not need a cable box to view
unscrambled cable channels.
▼
1
CHAPTER TWO: INSTALLATION
2.2
I N S TA L L AT I O N
Connecting to a Cable Box that Descrambles All Channels
Find the cable that is connected to the ANTENNA
OUT terminal on your
cable box.
This terminal might be labeled
“ANT OUT”, “VHF OUT” or simply,
“OUT”.
▼
1
2
Connect the other end of
this cable to the VHF/UHF
antenna terminal on the
back of the TV.
Connecting to a Cable Box that Descrambles Some Channels
If your cable box descrambles only some channels (such as premium channels), follow the
instructions below. You will need a two-way splitter, an RF (A/B) switch, and four lengths of
coaxial cable. (These items are available at most electronics stores.)
Find and disconnect the
cable that is connected to
the ANTENNA IN
terminal on your cable
box.
2
Connect this cable to a
two-way splitter.
3
Connect a coaxial cable
between an OUTPUT terminal on the splitter and
the IN terminal on the
cable box.
2.3
CHAPTER TWO: INSTALLATION
This terminal might be labeled
“ANT IN”, “VHF IN” or simply,
“IN”.
▼
1
I N S TA L L AT I O N
4
Connect a coaxial cable
between the ANTENNA
OUT terminal on the cable
box and the B–IN terminal
on the A/B switch.
5
Connect another cable
between the other OUT
terminal on the splitter
and the A–IN terminal on
the RF (A/B) switch.
6
Connect the last coaxial
cable between the OUT
terminal on the RF (A/B)
switch and the VHF/UHF
terminal on the rear of the
TV.
After you’ve made this connection, set the A/B switch to the “A” position for normal viewing. Set the A/B switch to the “B” position to view scrambled channels. (When you set the
A/B switch to “B”, you will need to tune your TV to the cable box’s output channel, which is
usually channel 3 or 4.)
Connecting a VCR
These instructions assume that you have already connected your TV to an antenna or a cable
TV system (according to the instructions on pages 2.1-2.3). Skip step 1 if you have not yet
connected to an antenna or a cable system.
1
Unplug the cable or
antenna from the back of
the TV.
2
Connect the cable or
antenna to the
ANTENNA IN terminal on
the back of the VCR.
CHAPTER TWO: INSTALLATION
2.4
I N S TA L L AT I O N
3
Connect a coaxial cable
between the ANTENNA
OUT terminal on the VCR
and the antenna
terminal on the TV.
A coaxial cable is usually included with a VCR. (If not, check your local electronics
store).
4
Connect a set of audio
cables between the
AUDIO OUT jacks on the
VCR and the AUDIO jacks
on the TV.
5
Connect a video cable
between the VIDEO OUT
jack on the VCR and the
VIDEO jack on the TV.
Follow the instructions in “Viewing a VCR or Camcorder Tape” to view your VCR tape.
2.5
CHAPTER TWO: INSTALLATION
I N S TA L L AT I O N
Connecting a Second VCR to Record from the TV
Your TV can send out signals of its picture and sound to be recorded by a second VCR.
To do this, connect your second VCR as follows:
1
Connect a set of audio
cables between the
AUDIO OUT jacks on the
TV and the AUDIO IN
jacks on the VCR.
(The VCR input jacks might be either on the front or on back of the VCR.)
2
Connect a video cable
between the VIDEO OUT
jack on the TV and the
VIDEO IN jack on the VCR.
Refer to your VCR’s instructions for more information about how to record using this kind
of connection.
Connecting a DVD Player
The rear panel jacks on your TV make it easy to connect a DVD player to your TV.
1
Connect a set of audio
cables between the
AUDIO INPUT 2 jacks on
the TV and the AUDIO
OUT jacks on the DVD
player.
2
Connect a video cable
between the DVD-IN (Y,
Pb, Pr) jacks on the TV
and the DVD-OUT (Y, Pb,
Pr) jacks on the DVD
player.
Note: For an explanation of Component video, see your DVD player's owner's manual.
CHAPTER TWO: INSTALLATION
2.6
I N S TA L L AT I O N
Connecting a Camcorder
The side panel jacks on your TV make it easy to connect a camcorder to your TV. They allow
you to view the camcorder tapes without using a VCR. (Also see “Viewing a VCR or
Camcorder Tape” on page 3.15)
1
Locate the A/V output
jacks on the camcorder.
They are usually found on
the side or back of the
camcorder.
2
Connect an audio cable
between the AUDIO OUTPUT jack on the camcorder and the AUDIO
terminals on the side of
the TV.
3
Connect a video cable
between the VIDEO OUTPUT jack on the camcorder and the VIDEO terminal on the side of the
TV.
The audio-video cables shown here are usually included with a Camcorder. (If not, check
your local electronics store.) If your camcorder is stereo, you need to connect a set of two
cables.
2.7
CHAPTER TWO: INSTALLATION
I N S TA L L AT I O N
Installing Batteries in the Remote Control
1
Slide the cover out completely.
Install two AA size
batteries.
Replace the cover.
Remove the batteries and store
them in a cool, dry place if you won’t
be using the remote control for a
long time.
▼
3
Make sure to match the “+” and
“–” ends of the batteries with the
diagram inside the compartment.
▼
2
The remote control can be used up
to about 23 feet from the TV.
(Assuming typical TV usage, the batteries last for about one year.)
CHAPTER TWO: INSTALLATION
2.8
C h a pOtP EeR AT
r I OTN h r e e
O P E R AT I O N
Turning the TV On and Off
Press the POWER button on the remote control.
You can also use the POWER button on the front panel.
Plug & Play Feature
When the TV is initially powered On, five basic customer settings proceed automatically
and subsequently: Setting the language, Video signal source, Ant. input check, Auto program, and Clock.
1
Press the POWER button
on the remote control.
The message “Plug &
Play” is displayed.
It flickers for a little while
and then the “Language”
menu is automatically
displayed.
2
Press the VOL+ or VOLbutton to select the
desired language.
Press the MENU button to
enter the language, and
then the “Channel” menu
is automatically displayed.
3
Press the VOL+ or VOLbutton to select the
desired video signal
source.
Press the MENU button to
enter the video signal
source, and then the
“Ant Input check” is
automatically displayed.
continued...
3.1
CHAPTER THREE: TV OPERATION
O P E R AT I O N
4
Make sure that the
antenna is connected to
the TV. And then press the
VOL+ or VOL- button to
activate "Auto Program" or
press the MENU button to
skip. (refer to “Auto
program” on page 3.6.)
5
Press the VOL+ or VOLbutton to move to the hour
or minute. Set the hour or
minute by pressing the
CH▲ or CH▼ button.
(refer to “Setting the
clock” on page 3.9.)
6
When you have finished,
press the MENU button.
The message “Enjoy your
watching..” is displayed.
7
If you want to reset this
feature
(1)Press the MENU button.
(2)Press the CH▼ button
three times to select the
Function menu and
press the VOL+ button.
(3)Press the CH▼ button
to select Plug & Play
and press the VOL+ button.
The message “Plug &
Play” is displayed.
Note: Plug & Play feature doesn’t work when in the A/V
mode.
CHAPTER THREE: TV OPERATION
3.2
O P E R AT I O N
Viewing the Menus and On-Screen Displays
Viewing the Menus
With the power on, press
the MENU button.
The on-screen menus disappear
from the screen after about thirty
seconds.
▼
1
The main menu appears
on the screen. Its left side
has four icons: Picture,
Sound, Channel, and
Function.
Use the CH▲ and CH▼ buttons to highlight one of the 4
icons. Then press the VOL+ button to access the icon’s submenu.
Press the MENU button to exit.
You can also use the MENU,
CHANNEL, and VOLUME buttons
on the control panel of the TV to
make selections.
▼
2
Viewing the Display
Press the DISPLAY button.
on the remote control.
The on-screen display
shows any or all of the
following: Active channel,
Audio source and the
time.
3.3
CHAPTER THREE: TV OPERATION
The on-screen displays
disappear after about twelve seconds.
▼
1
When Closed Caption has been set,
the icon(
) will appear by pressing the Display button.
O P E R AT I O N
Selecting a Menu Language
1
Press MENU to display
the menu.
Press CH ▼ three times to
select “Function”,
then press the VOL + button.
2
Press VOL + to select the
appropriate language:
English, Spanish, or
French.
3
Press MENU twice to exit.
CHAPTER THREE: TV OPERATION
3.4
O P E R AT I O N
Memorizing the Channels
Your TV can memorize and store all of the available channels for both “off-air” (antenna)
and cable channels. After the available channels are memorized, use the CH ▲ and
CH ▼ buttons to scan through the channels. This eliminates the need to change channels by entering the channel digits. There are three steps for memorizing channels:
selecting a broadcast source, memorizing the channels (automatic) and adding and
deleting channels (manual).
Selecting the Video Signal-source
Before your television can begin memorizing the available channels, you must specify
the type of signal source that is connected to the TV (i.e., an antenna or a cable system).
1
Press MENU to
display the menu.
Press CH ▼ two times to
select “Channel”, then
press the VOL + button.
2
Repeatedly press VOL +
to cycle through these
choices:
ANT (antenna),
STD, HRC or IRC (all cable
TV).
Note: STD, HRC and IRC identify various types of cable TV systems. Contact your local cable
company to identify the type of cable system that exists in your particular area.
At this point the signal source has been selected. Proceed to “Storing Channels in Memory”
(next page).
3
Press MENU twice to exit.
3.5
CHAPTER THREE: TV OPERATION
O P E R AT I O N
Storing Channels in Memory (Automatic Method)
1
First, select the correct
signal source (ANT, STD,
HRC, IRC). See steps 1~2
on previous page.
Press the MENU button,
then press the CH ▼ button twice to select
“Channel,” then press the
VOL + button.
2
Press the CH ▼ button to
select “Auto program”.
The TV automatically cycles
through all of the available channels
and stores them in memory. This
takes about one to two minutes.
Press the MENU button at any time
to interrupt the memorization
process and return to the Channel
menu.
▼
3
Press the VOL + button.
The TV will begin
memorizing all of the
available channels.
4
After all the available
channels are stored, the
Auto program menu reappears. Press the MENU
button twice to exit.
CHAPTER THREE: TV OPERATION
3.6
O P E R AT I O N
Adding and Erasing Channels (Manual Method)
1
Press the MENU button.
Press the CH ▼ button
twice to select “Channel”,
then press the VOL+ button.
2
Press the CH ▲ or CH ▼
button to select
“Add/Erase”.
Press the VOL+ button.
3
Press the VOL-/+ or number buttons to select the
channel you want added
or erased.
4
Press the CH ▲ or CH ▼
button to select “Select”.
Press the VOL+ or VOLbutton to select “Added”
or “Erased”.
Press the MENU button
three times to exit.
3.7
CHAPTER THREE: TV OPERATION
O P E R AT I O N
Changing Channels
Using the Channel Buttons
1
Press the CH ▲ or CH ▼ button to change channels.
When you press CH ▲ or CH ▼, the TV changes channels in sequence. You will see all the
channels that the TV has memorized. (The TV must have memorized at least three channels.)
You will not see channels that were either erased or not memorized.
Directly Accessing Channels
Use the number buttons to quickly tune to any channel.
1
Press the number buttons to go directly to a channel.
For example, to select channel 27, press “2”, then “7”.
The TV will change channels when you press the
second number.
When you use the number buttons, you can directly select channels that were either erased or
not memorized.
To select a channel over 100, press the +100 button. (For channel 122, press “+100”, then “2”,
then “2”.)
To change to single-digit channels (0–9) faster, press “0” before the
single digit. (For channel “4”, press “0”, then “4”.)
Using the PRE-CH Button to select the Previous Channel
Press the PRE-CH button.
The TV will switch to the last channel viewed.
To quickly switch between two
channels that are far apart, tune to
one channel, then use the number
button to select the second channel.
Then, use the PRE-CH button to
quickly alternate between them.
▼
1
Adjusting the Volume
Press the VOL + or VOL– button to increase or decrease the volume.
Using Mute
At any time, you can temporarily cut off the sound using the Mute button.
1
Press the MUTE button and the sound cuts off.
The word “Mute” will appear in the lower-left corner of the
screen.
2
To turn mute off, press the MUTE button again, or simply press
either the VOL – or VOL + button.
CHAPTER THREE: TV OPERATION
3.8
O P E R AT I O N
Setting the Clock
1
Press the MENU button to
display the on-screen
menu.
Press the CH ▼ button
three times to select
“Function”.
Press the VOL + button.
2
Press the CH ▼ button to
select “Time” menu.
Press the VOL + button:
The Time menu will
appear on the screen, and
“Clock” will be selected.
Press the VOL + button
again (the hours digits will
be selected). Press the CH
▲ or CH ▼ button repeatedly until the correct hour
appears.
When selecting the hours, be sure
to select the proper time of day (AM
or PM).
▼
3
You can change the hours by pressing
CH ▲ or CH ▼ repeatedly (or by
holding down either of these buttons).
After the hour is entered,
press the VOL + button.
(at this point the minutes
digits will be selected.)
Press the CH ▲ or CH ▼
button to select the
correct minutes.
After selecting the correct
minutes, press the VOL +
button.
Press the MENU button
three times to exit.
3.9
CHAPTER THREE: TV OPERATION
The time will appear every time
you press DISPLAY.
▼
4
O P E R AT I O N
Customizing the Picture
You can use the on-screen menus to change the contrast, brightness, tint, color, and
sharpness according to personal preference. (Alternatively, you can use one of the
“automatic” settings. See next page.)
1
Press MENU to display
menu.
2
Press VOL – or VOL +
repeatedly, until the
word “Custom” is
selected. (When Custom
is highlighted, the words
“Adjust” will appear on
the screen.)
Press CH ▼ to select
“Adjust”, then press
VOL+. (The words
Color Tone, Contrast,
Brightness, Sharpness,
Color, and Tint will
appear on the screen.)
Press CH ▲ or CH ▼ to
select a particular item.
The customer can select
“Normal”, “Warm”, or “Cool” according to personal preference.
▼
3
After adjusting an item, the gauge
will automatically disappear (after
about 5 seconds).
▼
4
Press VOL – or VOL +
to increase or
decrease the value of
a particular item.
Press MENU four
times to exit.
CHAPTER THREE: TV OPERATION
3.10
O P E R AT I O N
Using Automatic Picture Settings
Your TV has three automatic picture settings (“Dynamic”, “Standard”, and “Movie”) that
are preset at the factory. You can activate either Dynamic, Standard, or Movie by making a selection from the menu. Or, you can select “Custom” which automatically recalls
your personalized picture settings.
1
Press MENU to display
the menu.
2
Press VOL - or VOL + to
select the “Dynamic”,
“Standard”, “Movie” or
“Custom” picture setting.
•
•
•
•
3.11
Choose Dynamic for viewing the TV during the day or when there is brightlight in the room.
Standard: Optimal indoor screen condition.
Choose Movie when viewing the TV in low light, or when
playing video games.
Choose Custom if you want to adjust the settings according to personal preference (see “Customizing the Picture”, page 3.10).
CHAPTER THREE: TV OPERATION
O P E R AT I O N
Customizing the Sound
You can use the on-screen menus to adjust the bass, treble, and balance according to
individual preference. (Alternatively, you can use one of the “automatic” settings. See
next page.)
1
Press the MENU button to
display the menu.
Press the CH ▼ button to
select “Sound” menu.
2
Press the VOL - or VOL +
button repeatedly, until
the word “Custom” is
selected.
(When Custom is selected, the words “Adjust”
will appear on the
screen.)
3
Press the CH ▼ button to
select “Adjust”, then
press the VOL+ button.
(The words Bass, Treble,
and Balance will appear
on the screen.)
Press the CH ▲ or CH ▼
button to select a particular item to be changed.
4
Press the VOL – or VOL +
button to increase or
decrease the value of a
particular item.
Press the MENU button
four times to exit.
CHAPTER THREE: TV OPERATION
3.12
O P E R AT I O N
Using Automatic Sound Settings
Your TV has four automatic sound settings (“Standard”, “Music”, “Movie” and “Speech”)
that are preset at the factory. You can activate any of them by making a selection from the
on-screen menu. Or, you can select “Custom”, which automatically recalls your personalized
sound settings.
1
Press the MENU button to
display the menu.
Press the CH▼ button to
select “Sound” menu.
2
Press the VOL - or VOL +
button repeatedly to
select the “Standard”,
“Music”, “Movie”,
“Speech” or “Custom”
sound settings.
•
•
•
•
•
3.13
Choose Standard for the standard factory settings.
Choose Music when watching music videos or concerts.
Choose Movies when watching movies.
Choose Speech when watching a show that is mostly dialogue (i.e., news).
Choose Custom to recall your personalized settings.
CHAPTER THREE: TV OPERATION
O P E R AT I O N
Setting The On/Off Melody
You can hear clear melody sound when the TV is powered On or Off.
1
Press the MENU button to
display the menu.
Press the CH ▼ button to
select “Sound” menu ,
then press the VOL+ button.
2
Press the CH ▼ button to
select “Melody”, then
press the VOL+ or VOL–
button to select the “On”
or “Off”.
3
Press the MENU button
twice to exit.
CHAPTER THREE: TV OPERATION
3.14
O P E R AT I O N
Viewing a VCR or Camcorder Tape
You must select the appropriate mode in order to view the VCR or
Camcorder signal on the TV.
1
Press the MENU button to
display the menu.
Press the CH ▼ button
twice to select
“Channel”, then press the
VOL+ button.
2
Press the CH ▼ button
twice to select the
“TV/AV”.
3
Press the VOL+ or VOLbutton .
You will switch between
viewing the signals coming from equipment connected to the TV’s A/V
jacks, and the TV signal.
4
Press the MENU button
twice to exit.
3.15
CHAPTER THREE: TV OPERATION
Chapter Four
S P E C I A L F E AT U R E S
Customizing Your Remote Control (CL21M6W)
Your TV comes equipped with a “universal” remote control. In addition to
controlling the TV, the universal remote can also operate a VCR and a cable box
(even if your VCR and cable box are made by manufacturers other than Samsung).
Setting Up Your Remote Control to Operate Your VCR
1
Turn off your VCR.
2
On your Samsung remote control, press SET.
Press the VCR button on the top right of your remote control.
Enter both digits of the VCR code listed on the next page for
your brand of VCR.
Make sure you enter both digits of
the code, even if the first digit is a “0.”
If more than one code listed, try the
first one.
▼
4
The remote control has three
“modes”: “TV,” “VCR”, and “Cable”
Press the “VCR” button to switch the
remote control to the “VCR” mode.
▼
3
6
When your remote control is in
the “VCR” mode, the volume buttons
still control your TV’s volume.
▼
Once your remote control is set up, press the VCR button
any time you want to use the remote to operate your VCR.
▼
Press the POWER button on the remote control. Your VCR
should turn on. If your VCR turns on, your remote control is
now set correctly.
If your VCR does not turn on,
repeat steps 2, 3, and 4, but try one
of the other codes listed for the
brand of your particular VCR.
If no other codes are listed, try each
code, 000 through 72.
5
When your remote is in the “TV”
mode, the VCR control buttons (PLAY,
PAUSE, etc.) will still operate your
VCR.
CHAPTER FOUR: SPECIAL FEATURES
4.1
S P E C I A L F E AT U R E S
VCR Codes
4.2
CHAPTER FOUR: SPECIAL FEATURES
S P E C I A L F E AT U R E S
Setting Up Your Remote Control to Operate Your Cable Box
1
Turn off your
cable box.
2
On your Samsung remote control, press SET.
Press the CABLE button on the top right of your remote
control.
Enter both digits of the cable box code listed below for your
brand of cable box.
Press POWER. Your cable box should turn on. If your cable
box turns on, your remote control is now “set up” correctly.
Once your remote control is set up, press the CABLE button
any time you want to use the remote to operate your cable
box.
When your remote control is
in the “CABLE” mode, the volume
buttons still control your TV’s volume. Also, the VCR control buttons
(PLAY, PAUSE, etc.) will still operate
your VCR.
▼
6
If your cable box does not turn
on, repeat steps 2, 3, and 4, but try
one of the other codes listed for your
particular brand of cable box. (If no
other codes are listed, try each cable
box code, 00 through 35.)
▼
5
Make sure you enter both digits
of the code, even if the first digit is a
“0.” (If more than one code listed,
try the first one.)
▼
4
The remote control has three
“modes”: “TV,” “VCR,” and
“CABLE”.
Press the “CABLE” button to switch
the remote control to the “Cable”
mode.
▼
3
Cable Box Codes
CHAPTER FOUR: SPECIAL FEATURES
4.3
S P E C I A L F E AT U R E S
Fine Tuning Channels
Use fine tuning to manually adjust a particular channel for optimal reception.
1
Select the appropriate
channel.
Press the MENU button to
display the menu.
Press the CH ▼ button
twice to select “Channel”
menu, then press the
VOL+ button.
2
Press the CH ▼ button
three times to select “Fine
tune”, then press the
VOL+ button.
3
Press the VOL+ and VOLbuttons to adjust the fine
tuning.
Press the MENU button to
resume normal viewing.
▼
4
To store the fine tuning
setting in the TV’s memory, press the CH ▼ button
to select “Select”.
Press the VOL+ or VOLbutton to select “Added”.
To reset the fine tuning to
“0”, press the VOL+ or
VOL- button to select
“Erased”.
4.4
CHAPTER FOUR: SPECIAL FEATURES
S P E C I A L F E AT U R E S
Changing the Screen Size
1
Press the MENU button to
display the menu.
Press the VOL + button to
select the “Picture” menu.
2
Press the CH ▼ button to
select "Size".
3
Press the VOL + or VOL button repeatedly to
select “Normal” or
“Zoom”.
Press the MENU button
twice to exit.
•
•
Normal : Sets the picture to 4:3 normal mode. This is a standard TV screen size.
Zoom : Magnifies the size of the picture on screen.
CHAPTER FOUR: SPECIAL FEATURES
4.5
S P E C I A L F E AT U R E S
Digital Noise Reduction
If the broadcast signal received by your TV is weak, you can activate the Digital
Noise Reduction feature to help reduce any static and ghosting that may appear on
the screen.
1
Press the MENU button to
display the menu.
Press the VOL + button to
select the “Picture” menu.
2
Press the CH ▼ button to
select "Digital NR."
Pressing the VOL- or VOL+ button will alternate between “On” and
“Off”.
▼
3
Press the VOL + or VOL button to select Digital
NR “On”.
Press the MENU button to
exit.
4.6
CHAPTER FOUR: SPECIAL FEATURES
S P E C I A L F E AT U R E S
Using the Surf Feature
This feature allows you to set the TV to return to a particular channel after a certain
amount of time. For example, you may be watching a channel when commercials
start. You can set the Surf to “5 minutes”, then switch channels. After 5 minutes,
the TV will return to the original channel. To use the Surf:
1
While you are watching
the channel to which you
want to return, press the
R.SURF button. The onscreen display will read
“Surf off”.
2
Press the R.SURF button
again to set the timer in
thirty second intervals, up
to five minutes.
3
The time you set will begin counting down on the screen.
When the time runs out, the TV will return to the channel
you were watching when you set the timer.
CHAPTER FOUR: SPECIAL FEATURES
4.7
S P E C I A L F E AT U R E S
Setting the On/Off Timer
▼
Before using the timer, you must
set the TV’s clock. (See “Setting the
Clock” on page 3.9).
1
Press the MENU button to
display the menu.
Press the CH ▼ button
three times to select
"Function" menu, then
press the VOL+ button.
2
Press the CH ▼ button to
select "Time", then press
the VOL+ button.
When you set the hours, make
sure the correct time of day (AM or
PM) appears to the right of the hour.
▼
3
Press the CH ▼ button to
select "On time".
Press the VOL+ button to
select the “On time”
hours.
(The hours digits will be
highlighted.)
Press the CH ▲ or CH ▼
button repeatedly to
select the appropriate
hours (i.e., the hour when
the TV will turn on.)
4
Press VOL+ to select the
“On time” minutes.
(The minutes digits will be
highlighted.)
Press CH ▲ or CH ▼ to
select the appropriate
minutes.
4.8
CHAPTER FOUR: SPECIAL FEATURES
S P E C I A L F E AT U R E S
To deactivate the “On time,”
select “Off” during this step.
▼
5
Press the VOL + button to
select “On/Off.”
Press the CH ▲ (or CH ▼)
button to turn the ontimer “On.” (Repeatedly
pressing the CH ▲ or
CH ▼ button will alternate between on and off.)
6
When finished, press the
VOL + button .
If no function buttons
(including remote control buttons or
front panel buttons) are operated for
three hours after the TV is turned on
by “On time”, the TV will
automatically turn off.
▼
7
To set the Off time, press
the CH ▼ button to
select “Off time.”
Press the VOL + button
and set the hours and
minutes. (Follow the same
procedure as in steps 1~6
above.)
8
When finished setting the timer, press the MENU button
three times to exit.
Setting the Sleep Timer
The sleep timer automatically shuts off the TV after a preset time
(from 10 to 180 minutes).
After about 5 seconds, the sleep
display will disappear from the
screen, and the time interval will be
set.
▼
1
Press the SLEEP button on the remote control.
2
Press the SLEEP button repeatedly until the appropriate
time interval appears (any of the preset values from “Off” to
“180”).
CHAPTER FOUR: SPECIAL FEATURES
4.9
S P E C I A L F E AT U R E S
Sound Features
Choosing a Multi-Channel Sound (MTS) Soundtrack
Depending on the particular program being broadcast, you can listen to stereo, mono, or
a Separate Audio Program. (SAP audio is usually a foreign-language translation.
Sometimes SAP has unrelated information like news or weather.)
1
Press the MENU button
to display the menu.
Press the CH▼ button to
select the “Sound” menu,
then press the VOL+ button.
2
Press the CH▼ butto to
select “MTS”.
The text at the bottom of the
menu tells you if the incoming
audio is stereo, SAP, or mono.
▼
3
Press the VOL + or VOL button to select “Mono,”
“SAP,” or “Stereo.”
Press the MENU button
twice to exit
•
•
•
Choose Stereo for channels that are broadcasting in stereo.
Choose Mono for channels that are broadcasting in mono, or if you are
having difficulty receiving a stereo signal.
Choose SAP to listen to the Separate Audio Program, which is usually a
foreign-language translation.
You can also change the MTS setting by pressing the “MTS” button on the remote
control. (When you change channels, MTS is set to “Stereo” automatically.
To listen in ‘SAP’ or ‘Mono,’ change the MTS setting.)
4.10
CHAPTER FOUR: SPECIAL FEATURES
S P E C I A L F E AT U R E S
Extra sound settings (Turbo Sound, Surround, or Auto Volume )
• Turbo Sound
Turbo sound suitably emphasizes both higher and lower bands of sound (and includes
other effects).
• Surround
“Surround” converts a monaural sound signal into two identical left and right channels.
Once the “Surround” is set to “On” or “Off”, the setting applies to the sound effects such
as Standard, Music, Movie and Speech.
• Auto Volume
Each broadcasting station has its own signal conditions, and so it is not easy for you to
adjust the volume every time the channel is changed. “Auto volume” lets you automatically adjust the volume of the desired channel by lowering the sound output when the
modulation signal is high or by raising the sound output when the modulation signal is
low.
1
Press the MENU button to
display the menu.
Press the CH▼ button to
select the “Sound” menu,
then press the VOL + button.
2
Press the CH▼ button to
select “Turbo sound”.
3
Press the VOL + button to
select “On”.
Press the MENU button
twice to exit
You can set Surround and Auto volume the same way as setting Turbo
sound.
CHAPTER FOUR: SPECIAL FEATURES
4.11
S P E C I A L F E AT U R E S
Viewing Closed Captions
Your TV decodes and displays the closed captions that are broadcast with certain TV shows.
These captions are usually subtitles for the hearing impaired or foreign-language translations. All VCRs record the closed caption signal from television programs, so home-recorded video tapes also provide closed captions. Most pre-recorded commercial video tapes provide closed captions as well. Check for the closed caption symbol in your television schedule
and on the tape’s packaging:
.
1
Press the MENU button to
display the menu.
Press the CH ▼ button to
select the “Function”
menu.
Press the VOL+ button.
2
Press the CH ▼ button to
select the “Caption”
menu, then press the
VOL+ button.
Misspellings and unusual
characters sometimes occur during
closed caption transmissions, especially those of live events. There may be a
small delay before captions appear
when you change channels. These are
not malfunctions of the TV.
▼
3
Press the VOL+ or VOL –
button to turn closed captioning on/off.
In caption mode, captions
appear at the bottom of the screen,
and they usually cover only a small
portion of the picture.
▼
4
Press the CH ▼ button to
select “Mode”.
Press the VOL – or VOL +
button to select “Caption”
or “Text”.
Depending on the particular broadcast, it might be necessary to
make changes to “Channels” and “Field”:
Use the CH ▲, CH ▼, VOL + and VOL - buttons to make the
changes. (Follow the same procedure as in steps 3~4 above.)
Press the MENU button three times to exit.
4.12
CHAPTER FOUR: SPECIAL FEATURES
Different channels and fields
display different information: Field 2
carries additional information that
supplements the information in
Field 1. (For example, Channel 1
may have subtitles in English, while
Channel 2 has subtitles in Spanish.)
▼
5
In text mode, information unrelated
to the program, such as news or
weather, is displayed. Text often
covers a large portion of the screen.
S P E C I A L F E AT U R E S
Viewing the Demonstration
To become familiar with the various menus provided by your television, you can view the
in built demonstration.
1
Press the MENU button to
display the menu.
Press the CH ▼ button
to select the “Function”
menu.
Press the VOL+ button.
2
Press the CH ▼ button to
select “Demonstration”
menu.
Press the VOL+ button.
3
Each of the menu options
is displayed in turn.
When you wish to stop the
demonstration, press any
button on the remote control.
CHAPTER FOUR: SPECIAL FEATURES
4.13
Chapter Five
TROUBLESHOOTING
If the TV seems to have a problem, first try this list of possible problems and solutions.
If none of these troubleshooting tips apply, then call your nearest service center.
Identifying Problems
5.1
Problem
Possible Solution
Poor picture
Try another channel.
Adjust the antenna.
Check all wire connections.
Poor sound quality.
Try another channel.
Adjust the antenna.
No picture or sound.
Try another channel.
Press the TV/VIDEO button.
Make sure the TV is plugged in.
Check the antenna connections.
No color, wrong colors or tints.
Make sure the program is broadcast in color.
Adjust the picture settings.
If the set is moved or turned in a different
direction, the power should be OFF for
at least 30 minutes.
Picture rolls vertically.
Adjust the antenna.
Check all wire connections.
The TV operates erratically
Unplug the TV for 30 seconds, then try
operating it again.
The TV won’t turn on.
Make sure the wall outlet is working.
CHAPTER FIVE: TROUBLESHOOTING
APPENDIX
Cleaning and Maintaining Your TV
With proper care, your TV unit will give you many years of service. Please follow these
guidelines to get the maximum performance from your TV.
Placement
• Do not place the TV near extremely hot, cold, humid or dusty places.
• Do not place the TV near appliances with electric motors that create magnetic fields,
such as vacuum cleaners.
• Keep the ventilation openings clear; do not place the TV on a soft surface, such as
cloth or paper.
• Place the TV in a vertical position only.
Liquids
• Do not handle liquids near or on the TV. Liquids that spill into it can cause serious
damage.
Cabinet
• Never open the cabinet or touch the parts inside.
• Wipe your TV with a clean, dry cloth. Never use water, cleaning fluids, wax, or
chemicals.
• Do not put heavy objects on top of the cabinet.
Temperature
• If your TV is suddenly moved from a cold to a warm place, unplug the power cord,
and allow at least two hours for moisture that may have formed inside the unit to dry
completely.
Using Your TV in Another Country
If you plan to take your TV with you to a foreign country, please be aware of the different
television systems that are in use around the world. A TV designed for one system may
not work properly with another system due to differences in the TV channel frequencies.
Specifications
Model
Voltage
Frequency of Operation
Power Consumption
CL21M6W/CL21M5W
AC 100-240V
50/60Hz
110 W
APPENDIX
A.1
Download PDF

advertising