Samsung DVD-P181K User manual

Samsung DVD-P181K User manual
DVD Player
DVD-P181K
www.samsung.com/my
AK68-01640B
PRECAUTIONS
1. Setting up
- Refer to the identification label located on
the rear of your player for its proper operating voltage.
- Install your player in a cabinet with adequate ventilation holes. (7~10cm) Do not
block ventilation holes on any of the components for air circulation.
- Do not push the disc tray in by hand.
- Do not stack components.
- Be sure to turn all components off before
moving the player.
- Before connecting other components to this
player, be sure to turn them off.
- Be sure to remove the disc and turn off the
player after use, especially if you don’t use
it for a long time.
- The mains plug is as a disconnect device
and shall stay readily operable at any time.
2. For your safety
- This product utilizes a laser. Use of controls
or adjustments or performance of procedures other than those specified herein may
result in hazardous radiation exposure.
- Do not open covers and do not repair yourself. Refer servicing to qualified personal.
3. Caution
- Your player is not intended for industrial use
but for domestic purposes. Use of this product is for personal use only.
- Apparatus shall not be exposed to dripping
or splashing and no objects filled with liquids, such as vases, shall be placed on the
apparatus.
- Exterior influences such as lightning and
static electricity can affect normal operation
of this player. If this occurs, turn the player
off and on again with the POWER button, or
disconnect and then reconnect the AC
power cord to the AC power outlet. The
player will operate normally.
- When condensation forms inside the player
2
due to sharp changes in temperature, the
player may not operate
correctly. If this occurs, leave the player at
room temperature until the inside of the
player becomes dry and operational.
4. Disc
- Do not clean record-cleaning sprays, benzene, thinner, or other volatile solvents that
may cause damage to the disc surface.
- Do not touch the disc’s signal surface. Hold
by the edges or by one edge and the hole
in the center.
- Wipe the dirt away gently; never wipe a
cloth back and forth over the disc.
5. Environmental info
- The battery used in this product contains
chemicals that are harmful to the environ
ment.
- So, dispose of batteries in the proper man
ner, according to federal, state, and local
regulations.
The product unit accompanying this user manual is
licensed under certain intellectual property rights of
certain third parties. This license is limited to private
non-commercial use by end-user consumers for
licensed contents. No rights are granted for
commercial use. The license does not cover any
product unit other than this product unit and the
license does not extend to any unlicensed product
unit or process conforming to ISO/OUR 11172-3 or
ISO/OUR 13818-3 used or sold in combination with
this product unit. The license only covers the use of
this product unit to encode and/or decode audio files
conforming to the ISO/OUR 11172-3 or ISO/OUR
13818-3. No rights are granted under this license for
product features or functions that do not conform to
the ISO/OUR 11172-3 or ISO/OUR 13818-3.
CAUTION: USE OF ANY CONTROLS,
ADJUSTMENTS, OR PROCEDURES OTHER
THAN SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
Remote Control
Video/Audio
Cable
User’s Manual
Install Batteries in the Remote control
1. Open the battery cover on the back of the remote
control.
2. Insert two AAA batteries.
Make sure that the
polarities (+ and -) are aligned correctly.
3. Replace the battery cover.
If remote control doesn’t operate
properly:
- Check the polarity + - of the batteries (Dry-Cell)
- Check if the batteries are drained.
- Check if remote control sensor is blocked by
obstacles.
- Check if there is any fluorescent lighting nearby.
TABLE OF
CONTENT
Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Before you start . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Setup
General Features . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Disc Type and Characteristics . . . . . . . . . . . . . . . . 5
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Tour of the Remote Control . . . . . . . . . . . . . . . . . . 8
Connections
Choosing a Connection . . . . . . . . . . . . . . . . . . . . . 9
Basic Functions
Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Using the Search and Skip Functions . . . . . . . . . 15
Using the Display Function . . . . . . . . . . . . . . . . . 15
Using the Disc and Title Menu . . . . . . . . . . . . . . 15
Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Slow Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Advanced Functions
Adjusting the Aspect Ratio (EZ View) . . . . . . . . . 17
Selecting the Audio Language . . . . . . . . . . . . . . . 17
Selecting the Subtitle Language. . . . . . . . . . . . . . 18
Changing the Camera Angle . . . . . . . . . . . . . . . . 18
Using the Bookmark Function . . . . . . . . . . . . . . . 18
Using the Zoom Function . . . . . . . . . . . . . . . . . . . 19
Clips Menu for MP3/WMA/JPEG/
CD Audio/MPEG4. . . . . . . . . . . . . . . . . . . . . . . . . 19
Folder Selection . . . . . . . . . . . . . . . . . . . . . . . . . . 19
MP3/WMA/CD Audio Playback. . . . . . . . . . . . . . . 19
MPEG4 Playback . . . . . . . . . . . . . . . . . . . . . . . . . 20
Picture CD Playback. . . . . . . . . . . . . . . . . . . . . . . 21
Karaoke Functions
Karaoke Functions . . . . . . . . . . . . . . . . . . . . . . . . 22
Changing Setup Menu
Using the Setup Menu . . . . . . . . . . . . . . . . . . . . . 22
Setting Up the Language Features . . . . . . . . . . . 23
Setting Up the Audio Options . . . . . . . . . . . . . . . . 24
Setting Up the Display Options . . . . . . . . . . . . . . 25
Setting Up the Parental Control . . . . . . . . . . . . . . 26
Reference
Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . 28
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
3
English
BEFORE YOU
STAR T
SETUP
General Features
Excellent Sound
Dolby Digital, a technology developed by Dolby
Laboratories, provides crystal clear sound reproduction.
Screen
Both regular and widescreen(16:9) pictures can be
viewed.
Slow Motion
An important scene can be viewed in slow motion.
Parental Control (DVD)
The parental control allows users to set the level
necessary to prohibit children from viewing harmful
movies such as those with violence, adult subject
matter, etc.
Various On-Screen Menu Functions
You can select various languages (Audio/Subtitle)
and screen angles while enjoying movies.
Progressive Scan
Progressive scanning creates an improved picture
with double the scan lines of a conventional interlaced picture.
EZ VIEW (DVD)
Easy View enables picture adjustment to match
your TV's screen size (16:9 or 4:3).
Digital Photo Viewer (JPEG)
You can view Digital Photos on your TV.
Repeat
You can repeat a song or movie simply by pressing
the REPEAT button.
MP3/WMA
This unit can play discs created from MP3/WMA
files.
MPEG4
This unit can play MPEG4 formats within an
avi file.
Note
- Discs which cannot be played with this
player.
• DVD-ROM
• DVD-RAM
• CD-ROM
• CDV
• CDI
• CVD
• CDGs play audio only, not graphics.
4
- Ability to play back may depend on recording
conditions.
• DVD-R, +R
• CD-RW
• DVD+RW, -RW (V mode)
- The unit may not play certain CD-R, CD-RW
and DVD-R due to the disc type or recording
conditions.
COPY PROTECTION
Many DVD discs are encoded with copy protection.
Because of this, you should only connect your DVD
player directly to your TV, not to a VCR. Connecting
to a VCR results in a distorted picture from copyprotected DVD discs.
This product incorporates copyright protection
technology that is protected by methods claims of
certain U.S. patents and other intellectual property
rights owned by Macrovision Corporation and other
rights owners. Use of this copyright protection technology must be auzthorized by Macrovision
Corporation, and is intended for home and other
limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
PROGRESSIVE SCAN OUTPUTS
(525p)
“CONSUMERS SHOULD NOTE THAT NOT ALL
HIGH DEFINITION TELEVISION SETS ARE FULLY
COMPATIBLE WITH THIS PRODUCT AND MAY
CAUSE ARTIFACTS TO BE DISPLAYED IN THE
PICTURE, IN CASE OF 525 PROGRESSIVE
SCAN PICTURE PROBLEMS, IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION TO THE ‘STANDARD DEFINITION’ OUTPUT. IF THERE ARE QUESTIONS
REGARDING YOUR TV SET COMPATIBILITY
WITH THIS MODEL 525p DVD PLAYER, PLEASE
CONTACT SAMSUNG'S CUSTOMER SERVICE
CENTER.”
Disc Type and Characteristics
Disc Types (Logos)
Recording Types
DVD
Audio
+
Video
VIDEO-CD
Audio
+
Video
AUDIO-CD
Disc Size
Max. Playing Time
Characteristics
12 Cm
Single-sided 240 min.
Double-sided 480 min.
8 Cm
Single-sided 80 min.
Double-sided 160 min.
- DVD contains excellent sound
and video due to Dolby Digital
and MPEG-2 system.
- Various screen and audio functions can be easily selected
through the on-screen menu.
12 Cm
74 min.
8 Cm
20 min.
12 Cm
74 min.
8 Cm
20 min.
Audio
Disc Markings
~
PAL
Play Region Number
PAL broadcast system in
U.K, France, Germany, etc.
Dolby Digital disc
STEREO
DIGITAL
SOUND
Stereo disc
- Video with CD sound, VHS quality & MPEG-1 compression technology.
- CD is recorded as a Digital
Signal with better audio quality,
less distortion and less deterioration of audio quality over time.
Region Number
Both the DVD player and the discs are coded
by region. These regional codes must match in
order for the disc to play. If the codes do not
match, the disc will not play.
The Region Number for this player is
described on the rear panel of the player.
Digital Audio disc
DivX Certification
DTS disc
DivX, DivX Certified, and associated logos are trademarks of
DivXNetworks, Inc and are used
under license.
MP3 disc
You must only insert one DVD disc at a
time. Inserting two or more discs will not
allow to play them back and it may cause
damage to the DVD player.
5
English
This DVD player is capable of playing the following types of discs with the corresponding logos:
Description
Front Panel Controls
1
1.
2.
3.
4.
2
3
STANDBY/ON ( )
When STANDBY/ON is pressed on, the indicator
goes out and the player is turned on.
STANDBY indicator
When the unit is first plugged in, this indicator
lights.
DISC TRAY
Place the disc here.
MIC
Connect Microphone for karaoke functions.
4
5
6
7
8
5.
MICROPHONE VOLUME
Use to adjust microphone volume level. Use the button
by pressing it. Turn it to the left or right to control the
volume.
6.
DISPLAY
Operation indicators are displayed here.
OPEN/CLOSE /STOP ( )
Stops disc play.
Press to open and close the disc tray.
PLAY/PAUSE (
)
Begin or pause disc play.
7.
8.
Front Panel Display
Total playing time/Displays various messages concerning operations such as PLAY,
STOP, LOAD ...
nodSC: No disc loaded.
OPEn: The disc tray is open.
LOAd: Player is loading disc information.
6
Rear Panel
English
4
1
2 3
1.
AUDIO OUT JACKS
- Connect to the Audio input jacks of your television or
audio/video receiver.
2.
VIDEO OUT JACK
- Use a video cable to connect to the Video input jack
on your television.
3.
COMPONENT VIDEO OUT JACKS
- Use these jacks if you have a TV with Component
Video in jacks. These jacks provide PR, PB and Y
video.
- If P-SCAN Video Output is selected in Setup Menu,
progressive scan mode will work.
- If I-SCAN Video Output is selected in Setup Menu,
4.
DIGITAL AUDIO OUT JACKS
- Use either coaxial digital cable to connect to a compatible Dolby Digital receiver.
- Use either coaxial digital cable to connect to an A/V
Amplifier that contains a Dolby Digital, MPEG2 or
DTS decoder.
Note
- Consult your TV User’s Manual to find out if your TV supports Progressive Scan.
If Progressive Scan is supported, follow the TV User’s Manual regarding Progressive Scan
settings in the TV’s menu system.
- See pages 22 to get more information on how to use the setup menu.
7
Tour of the Remote Control
6.
7.
16
17
8.
18
9.
10.
3
19
11.
4
20
12.
5
6
7
8
9
10
21
1
2
22
13.
23
24
14.
15.
11
16.
17.
12
25
13
26
18.
14
15
27
28
19.
20.
21.
22.
23.
1.
DVD Power Button
Turns the power on or standby.
2.
NUMBER Buttons
3.
TITLE MENU (number 7) Button
24.
25.
26.
Brings up the Title menu.
4.
5.
8
ZOOM/- /-- Button
Enlarge DVD Picture
Use this button to select the channel of TV program by inserted the channel number (TV mode).
TV VOLUME
TV VOL(+,-) button
27.
28.
SEARCH Buttons (
)
/
Allow you to search forward/backward through a disc.
VIDEO SEL.Button
Change video output mode
SKIP Buttons (
)
/
Use to skip the title, chapter or track.
STOP Button (
)
MENU Button
Brings up the DVD player’s menu.
œ/ƒ,¦/‹ Buttons
ENTER/œ
This button functions as a toggle switch.
EZ VIEW Button
The aspect ratio of a picture can easily be adjusted
according to the screen size of your TV (16:9 or 4:3)
DISC MENU Button
Brings up the Disc menu.
OPEN/CLOSE (
) Button
To open and close the disc tray
AUDIO Button
Use this button to access various audio functions on a disc.
DVD Button
Use to operate DVD
TV Button
Use to operate TV
KARAOKE (Number 8) Button
Use to begin Karaoke functions.
BOOKMARK (Number 9 Button)
Quickly find bookmark sections of a DVD or VCD.
STEP /TV SOURCE Button
Advances play one frame at a time/Press this button to
select an available TV source (TV mode).
TV CH Buttons
Use to change channel.
SUBTITLE Button
PLAY/PAUSE Button (
)
Begin/Pause disc play.
RETURN Button
Returns to a previous menu.
INFO Button
Displays the current disc mode.
CANCEL Button
Use to remove menus or status displays from the
screen.
REPEAT A-B Button
Allows you to repeat A-B disc.
REPEAT Button
Allows you to repeat play a title, chapter, track, or disc.
CONNECTIONS
The following shows examples of connections commonly used to connect the DVD player with a TV and
other components.
Before Connecting the DVD Player
- Always turn off the DVD player, TV, and other components before you connect or disconnect any cables.
- Refer to the user’s manual of the additional components you are connecting for more information on those
particular components.
Connection to a TV (For Video)
1
Using component video cables (not included), connect the
VIDEO OUT on the rear of the DVD player to the VIDEO
IN terminal of TV.
WHITE
RED
2
Turn on the DVD player and TV.
YELLOW
Video Cable
Audio Cable
RED
WHITE
YELLOW
3
Press the TV/VIDEO button on the TV's remote
control to select Video.
Note
- Noise may be generated if the audio cable is too close to the power cable.
- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 12 to 13)
- The number and position of terminals can vary depending on your TV set. Please refer to the user's manual of the TV.
- If you press the VIDEO SEL. button when DVD Player is in stop mode or no disc is inserted, the Video
Output mode changes in the following sequence: (I-SCAN ➝ P-SCAN).
9
English
Choosing a Connection
Connection to a TV (Interlace)
- Connecting to your TV using Component video cables.
- You will enjoy high quality and accurate color reproduction images. Component video separates the picture element into black and white(Y), blue(PB), red(PR) signals to present clear and clean images. (Audio
signals are delivered through the audio output.)
1
Using component video cables (not included), connect the
COMPONENT VIDEO OUT terminal on the rear of the
DVD player to the COMPONENT IN terminal of TV.
2
WHITE
Using the audio cables, connect the AUDIO (red and
white) OUT on the rear of the DVD player to the AUDIO
(red and white) IN terminals of TV. Turn on the DVD player and TV.
RED
BLUE
GREEN
RED
Component cable
(not included)
Audio Cable
3
RED
WHITE
RED
BLUE GREEN
Press the TV/VIDEO button on the TV's remote control to
select Component or DVD.
4
Set the Video Output to Component (I-SCAN) in the
Display Setup menu. (See pages 25)
Note
- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 12 to 13)
- The component terminal of TV can be marked by “R-Y, B-Y, Y” or “Cr, Cb, Y” instead of “PR, PB, Y”
depending on the manufacturer. The number and position of terminals can vary depending on the TV set.
Please refer to the user's manual of the TV.
10
Connection to a TV (Progressive)
1
English
Using component video cables (not included), connect the
COMPONENT VIDEO OUT terminal on the rear of the
DVD player to the COMPONENT IN terminal of TV.
2
Using the audio cables, connect the AUDIO (red and
white) OUT on the rear of the DVD player to the AUDIO
(red and white) IN terminals of TV. Turn on the DVD player and TV.
WHITE
BLUE
RED
GREEN
RED
3
Press the input selector on your TV remote control until the
Component signal from the DVD player appears on the TV
screen.
Component cable
(not included)
Audio Cable
RED
WHITE
RED
BLUE GREEN
4
Set the Video Output to Component (P-SCAN) in the
Display Setup menu. (See pages 25)
To see the progressive video output,
-You
Consult
TVsupporting
User’s Manual
to find out
need ayour
TV set
the progressive
scanif your TV supports Progressive Scan. If Progressive
Scan isfunction.
supported,
follow
TV up
User’s
Manual regarding Progressive Scan settings in the TV’s
input
And you
havethe
to set
the TV
menu system.
- Depending on your TV, the connection method may differ from the illustration above.
Note
- What is "Progressive Scan"?
Progressive scan has twice as many scanning lines as the interlace output method has. Progressive
scanning method can provide better and clearer picture quality.
11
Connection to an Audio System (2 Channel Amplifier)
1
Using the audio cables, connect the AUDIO (red and
white) OUT on the rear of the DVD player to the AUDIO
(red and white) IN terminals of the Amplifier.
2
Using the video signal cable(s), connect the VIDEO or
COMPONENT OUT terminals on the rear of the DVD player to the VIDEO orCOMPONENT IN terminal of your TV.
WHITE
RED
3
Audio Cable
Turn on the DVD player, TV, and Amplifier.
RED
WHITE
4
Press the input select button of the Amplifier to select external input in order to hear sound from the DVD player.
Note
- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause
damage to the speakers and your ears.
- Please set the audio in the menu screen according to the Amplifier. (See pages 24)
- The position of terminals can vary depending on the Amplifier.
Please refer to the user's manual of the Amplifier.
12
Connection to an Audio System (Dolby digital, MPEG2 or DTS Amplifier)
1
English
If using a coaxial cable (not included), connect the DIGITAL AUDIO OUT (COAXIAL) terminal on the rear of the
DVD player to the DIGITAL AUDIO IN (COAXIAL) terminal of the Amplifier.
2
Using the video signal cable(s), connect the VIDEO or
COMPONENT OUT terminals on the rear of the DVD player to the VIDEO or COMPONENT IN terminal of TV.
Audio Cable
3
Turn on the DVD player, TV, and Amplifier.
4
Press the input select button of the Amplifier to select
external input in order to hear sound from the DVD player.
Note
- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause
damage to the speakers and your ears.
- Please set the audio in the menu screen according to the Amplifier. (See pages 24)
- The position of terminals can vary depending on the Amplifier.
Please refer to the user's manual of the Amplifier.
13
BASIC FUNCTIONS
Playing a Disc
Before Play
- Turn on your TV and set it to the correct Video
Input by pressing TV/VIDEO button on the TV
remote control.
- If you connected an external Audio System, turn
on your Audio System and set it to the correct
Audio Input.
After plugging in the player, the first time you press the DVD
POWER button, this screen comes up: If you want to select
a language, press a NUMBER button. (This screen will only
appear when you plug in the player for the first time.)
If the language for the startup screen is not set, the settings
may change whenever you turn the power on or off.
Therefore, make sure that you select the language you want
to use.
Once you select a menu language, you can change it by
pressing the
button on the front panel of the unit for
more than 5 seconds with no disc in the unit. Then the
SELECT MENU LANGUAGE window appears again where
you can reset your preferred language.
SELECT MENU LANGUAGE
Press
1
for English
Touche
2
pour Français
Drücken Sie
3
für Deutsch
Pulsar
4
para Español
Premere
5
per Italiano
Druk op
6
voor Nederlands
4. Stopping Play
Press the STOP ( ) button during play.
5. Removing Disc
Press the OPEN/CLOSE ( ) button.
6. Pausing Play
Press the PLAY/PAUSE ( ) or STEP button on the
remote control during play.
- Screen stops, no sound.
To resume, press the PLAY/PAUSE ( )
button once again.
7. Step Motion Play (Except CD)
Press the STEP button on the remote control during play.
- Each time the button is pressed, a new frame will
appear.
- No sound is heard during STEP mode.
- Press the PLAY/PAUSE ( ) button to resume
normal play.
- You can only perform step motion play in the
forward direction.
8. Slow Motion Play
Press SEARCH ( ) button to choose
the play speed between 1/2, 1/4, 1/8 and 1/16 of normal
during PAUSE or STEP mode.
- No sound is heard during slow mode.
- Press the PLAY/PAUSE ( ) button to resume
normal play.
- Reverse slow motion play will not work.
Playback
1. Press the OPEN/CLOSE ( ) button. The STANDBY
indicator light goes out and the tray opens.
2. Place a disc gently into the tray with the disc’s label facing
up.
- You must only insert one DVD disc at a time.
Inserting two or more discs will not allow to play
them back and it may cause damage to the DVD
player.
3. Press the PLAY/PAUSE ( ) button or OPEN/ CLOSE
( ) button to close the disc tray.
- When you stop disc play, the player remembers
where you stopped, so when you press
PLAY/PAUSE ( ) button again, it will pick up where
you left off. (unless the disc is removed or the player
is unplugged, or if you press the STOP ( ) button
twice.)
14
Note
- If the player is left in the stop mode for more
than one minute without any user interaction, a
screen saver will be activated. Press the
PLAY/PAUSE ( ) button to resume normal play.
- If the player is left in the stop mode for more than
about 30 minutes, the power will automatically
shut off. (Automatic Power-Off Function)
- If the player is left for about 5 minutes in pause
mode, it will stop.
- This (
) icon indicates an invalid button press.
During play, you can search quickly through a chapter or track, and use the skip function to jump to the
next selection.
Searching through a Chapter or
Track.
During play, press the SEARCH (
the remote control.
or
2. Press the œ/ƒbuttons to select the desired item.
3. Press the ¦/‹ buttons to make the desired setup and then
press the ENTER button.
- You may use the number buttons of the remote control
to directly access a title, chapter or to start the
playback from the desired time.
4. To make the screen disappear, press the RETURN button
again.
) button on
Note
DVD
2X, 4X, 64X, 128X
VCD
4X, 8X
CD
2X, 4X, 8X
To access the desired title when there is
more than one in the disc. For example, if
there is more than one movie on a DVD,
each movie will be identified.
Note
- The speed marked in this function may be different from
the actual speed of playback.
Allows playback of the film from a desired
time. You must enter the starting time as a
reference.The time search function does not
operate on some disc.
Skipping Tracks
During play, press the SKIP (
or
) button.
- When playing a DVD, if you press the SKIP (
Most DVD discs are recorded in chapters so
that you can quickly find a specific passage
) button, it
moves to the next chapter. If you press the SKIP (
)
button, it moves to the beginning of the chapter. One more
Refers to the language of the film soundtrack.
In the example, the soundtrack is played in
English 5.1CH. A DVD disc can have up to
eight different soundtracks.
press makes it move to the beginning of the previous
chapter.
- When playing a VCD 2.0 in Menu Off mode, or a VCD 1.1
or a CD, if you press the SKIP (
) button, it moves to
the next track. If you press the SKIP (
) button, it moves
to the beginning of the track. One more press makes it
move to the beginning of the previous track.
- If a track exceeds 15 minutes when playing a VCD and
you press the
If you press the
Refers to the subtitle languages available in
the disc. You will be able to choose the
subtitle languages or, if you prefer, turn them
off from the screen. A DVD disc can have up
to 32 different subtitles.
To access the desired Angle function.
Some DVD discs are have more angle function from any picture.
button, it moves forward 5minutes.
button, it moves backward 5 minutes.
Note
Only Menu Off is available for VCD2.0. Each press of the
DISC MENU button toggles between Menu On and Menu
Off.
Using the Display Function
When Playing a DVD/VCD/MPEG4
1. During play, press the INFO button on the remote control.
Using the Disc and Title
Menu
Using the Disc Menu
1. Press the MENU button on the remote control.
2. Press the œ/ƒ buttons to select Disc Menu, then press the
‹ or ENTER button.
.. L a n g u a g e S e t u p P a g e . .
Player Menu
E N G
Disc Menu
E N G
Audio
ORI
Subtitle
A U T O
15
English
Using the Search and Skip
Functions
Note
DVD/VCD
- Depending on a disc, the Disc Menu may not work.
- You can also use the Disc Menu, using the DISC
MENU button on the remote control.
- Only Menu Off is available for VCD2.0. Each press of
the DISC MENU button toggles between Menu On and
Menu Off.
Repeat Play
Press the REPEAT button to change playback
mode.
When playing a DVD/VCD
- DVD repeat play by chapter,title or disc VCD
repeat play by disc or track.
- Chapter : repeats the chapter that is playing.
- Title : repeats the title that is playing.
- Disc : repeats the disc that is playing.
- Track : repeats the track that is playing.
- Off
T
(
Not
- A-B REPEAT allows you to set point(B) directly
after point (A) has been set.
- Depending on a disc, the Repeat function may
not work.
- Only Menu Off is available for VCD2.0. Each
press of the DISC MENU button toggles
between Menu On and Menu Off.
Slow Play
This feature allows you slowly to repeat scenes containing sports, dancing, musical instruments being
played etc., so you can study them more closely.
When playing a DVD/VCD
1. During play, press the PLAY/PAUSE (
) button.
2. Press the SEARCH ( ) button repeatedly to choose
the play speed between 1/2, 1/4,1/8,1/16 of normal during
PAUSE mode.
Using the A-B Repeat function
1. Press the REPEAT A-B button on the remocon at the point
where you want repeat play to start (A).
2. Press the REPEAT A-B button on the remocon at the
point where you want the repeat play to stop (B).
3. To return to normal play, press REPEAT A-B button
again.
16
-
If you are using a 4:3 TV
Adjusting the Aspect Ratio
(EZ View)
To play back using aspect ratio
(DVD)
Press the EZ VIEW button.
- The screen size changes when the button is pressed
repeatedly.
- The screen zoom mode operates differently depending on the
screen setting in the Display Setup menu.
- To ensure correct operation of the EZ VIEW button, you
should set the correct aspect ratio in the Display Setup
menu. (See pages 25).
If you are using a 16:9 TV
For 16:9 aspect ratio discs
- WIDE SCREEN
Displays the content of the DVD title in 16:9 aspect ratio.
- SCREEN FIT
The top and bottom portions of the screen are cut off.
When playing a 2.35:1 aspect ratio disc, the black bars at
the top and bottom of the screen will disappear. The picture
will look vertically stretched. (Depending on a type of disc,
the black bars may not disappear completely.)
- ZOOM FIT
The top, bottom, left and right of the screen are cut off and
the central portion of the screen is enlarge
For 16:9 aspect ratio discs
- 4:3 Letter Box
Displays the content of the DVD title in 16:9 aspect ratio. The
black bars will appear at the top and bottom of the screen.
- 4:3 Pan&Scan
The left and right portions of the screen are cut off and the
central portion of the 16:9 screen is displayed.
- SCREEN FIT
The top and bottom portions of the screen are cut off and a
full screen appears. The picture will look vertically stretched.
- ZOOM FIT
The top, bottom, left and right of the screen are cut off and
the central portion of the screen is enlarged.
For 4:3 aspect ratio discs
- Normal Screen
Displays the content of the DVD title in 4:3 aspect ratio.
- SCREEN FIT
The top and bottom portions of the screen are cut off and the
full screen appears. The picture will look vertically stretched.
- ZOOM FIT
The top, bottom, left and right portions of the screen are cut
off and the central portion of the screen is enlarged.
Note
This function may behave differently depending on
the type of disc.
Selecting the Audio
Language
You can select a desired audio language quickly and
easily with the AUDIO button.
Using the AUDIO button
1. Press the Audio button. The Audio changes when the audio
button is press repeatedly.
The audio languages are represented by
abbreviations.
DVD
For 4:3 aspect ratio discs
- Normal Wide
Displays the content of the DVD title in 16:9 aspect ratio.
The picture will look horizontally stretched.
- SCREEN FIT
The top and bottom portions of the screen are cut off and
the full screen appears.
The picture will look vertically stretched.
- ZOOM FIT
The top, bottom, left and right portions of the screen are
cut off and the central portion of the screen is enlarged.
- Vertical Fit
When a 4:3 DVD is viewed on a 16:9 TV, black bars will
appear at the left and right of the screen in order to prevent
the picture from looking horizontally stretched.
When playing a VCD,
you can select among
STEREO, LEFT,
RIGHT.
2. To remove the AUDIO icon, press the CANCEL or RETURN button.
17
English
ADVANCED
FUNCTIONS
Note
- This function depends on audio languages are
encoded on the disc and may not work.
- A DVD disc can contain up to 8 audio languages.
- To have the same audio language come up
whenever you play a DVD;
Refer to “Using the Audio Language” on page
23.
Selecting the Subtitle
Language
You can select a desired subtitle quickly and easily
with the SUBTITLE button.
Using the SUBTITLE button (DVD)
Using the Bookmark
Function
This feature lets you bookmark sections of a DVD or
VCD (Menu Off mode) so you can quickly find them
at a later time.
Using the Bookmark Function
(DVD/VCD)
1. During play, press the Bookmark button on the remote
control.
DVD/VCD
1. Press the SUBTITLE button. The subtitle languages are
represented by abbreviations. The subtitle changes when
the button is pressed repeatedly.
DVD
Bookmark
Clear
Play
2. When you reach the scene you want to mark, press the
ENTER button. Up to12 scenes may be marked at a time.
English
Bookmark
1
TT:01 CH:05 Time 0:39:23
Clear
Play
Note
- You have to change the desired subtitle in the
Disc Menu, according to discs. Press the INFO
MENU button.
- This function depends on what subtitles are
encoded on the disc and may not work on all
DVDs.
- A DVD disc can contain up to 32 subtitle
languages.
- To have the same subtitle language come up
whenever you play a DVD; Refer to “Using the
Subtitle Language” on page 23.
Note
- Depending on a disc, the Bookmark function
may not work.
Recalling a Marked Scene
1. During play, press the bookmark button on the remocon
2. Press the œ/ƒ¦/‹ buttons to select a marked scene.
Bookmark
1
2
TT:01 CH:05 Time 0:39:23
Clear
Play
Changing the Camera
Angle
When a DVD contains multiple angles of a particular
scene, you can use the ANGLE function.
Using the ANGLE Function (DVD).
If the disc contains multiple angles, the ANGLE
appears on the screen.
3. Press the PLAY/PAUSE (
scene.
) button to skip to the marked
Clearing a Bookmark
1. During play, press the Bookmark button on the remocon.
2. Press the œ/ƒ¦/‹ buttons to select the bookmark number you want to delete.
3. Press the CANCEL button to delete a bookmark number.
1. During play, press the INFO button on the remote control.
2. Press the œ/ƒ buttons to select
3. Press the ¦/‹ buttons or you can use the number buttons
on the remote control to select the desired angel Angle.
18
Bookmark
1
2
3
TT:01 CH:05 Time 0:39:23
Play
Clear
Using the Zoom Function
(DVD/VCD)
- During DVD or VCD play or pause mode, press ZOOM
button on the remocontrol repetedly to zoom in
2X/3X/4X
- During VCD play, press ZOOM button to zoom in
2X/4X/2X/Normal in order.
: STOP file icon.
-
: PLAY file icon
-
: WMA file icon
-
: MP3 file icon.
-
: JPG file icon.
-
: AVI file icon.
-
: CD file icon.
-
: Folder file icon
-
: current file icon
Folder Selection
Clips Menu for
MP3/WMA/JPEG/CD
Audio/MPEG4
CD Audio or discs with MP3/WMA/JPEG/MPEG4
contain individual songs and/or pictures that can be
organized into folders as shown below. They are similar to how you use your computer to put files into different folders.
Open the disc tray.
Place the disc on the tray.
Close the tray.
The tray closes and this
screen displays.
-
English
Using the Zoom Function
001/004
Off
- To select the Parent Folder
Press the RETURN button to go to parent folder, or press the
œ/ƒ
ƒ buttons to select “..” and press ENTER to go to the
parent folder.
MP3/WMA/CD Audio Playback
1. Open the disc tray. Place the disc on the tray. Close the tray.
- Only one kind of file is played back when a disc or a
folder contains both MP3 and WMA files.
ƒ buttons to select a song file.
2. Press the œ/ƒ
Press ENTER to begin playback of the song file.
00:01 03:12
Off
001/004
128kbps
track 1
-
: Current Playback Mode : There are four
track 2
track 3
track 4
modes. They can be selected in order by
pressing the REPEAT button.
- Off: Normal Playback
- Track: Repeats the current track.
- Folder: Repeats the current folder.
- Random: Files in the disc will be played in
random order.
Repeat/Random playback
Press the REPEAT button to change the playback mode. There
are four modes, such as Off, Track, Folder and Random.
- Off: Normal Playback
- Track: Repeats the current song file.
- Folder: Repeats the song files which have the same
extension in the current folder.
- Random: Song files which have the same extension will be
played in random order.
19
CD-R MP3/WMA file
When you record MP3 or WMA files on CD-R, please refer
to the following.
- Your MP3 or WMA files should be ISO 9660 or JOLIET
format.
ISO 9660 format and Joliet MP3 or WMA files are
compatible with Microsoft's DOS and Windows, and with
Apple's Mac. This format is the most widely used.
- When naming your MP3 or WMA files, do not exceed 8
characters, and enter “.mp3, .wma” as the file extension.
General name format : Title.mp3. or Title.wma. When
composing your title, make sure that you use 8 characters or
less, have no spaces in the name, and avoid the use of
special characters including: (.,/,\,=,+).
- Use a decompression transfer rate of at least 128 Kbps
when recording MP3 files.
Sound quality with MP3 files basically depends on the rate of
compression/decompression you choose. Getting CD audio
sound requires an analog/digital sampling rate, that is
conversion to MP3 format, of at least 128 Kbps and up to 160
Kbps. However, choosing higher rates, like 192 Kbps or more,
only rarely give better sound quality. Conversely, files with
decompression rates below 128 Kbps will not be played
properly.
- Use a decompression transfer rate of at least 64Kbps
when recording WMA files.
Sound quality with WMA files basically depends on the rate of
compression/decompression you choose.
Getting CD audio sound requires an analog/digital sampling
rate, that is conversion to WMA format, of at least 64Kbps
and up to 192Kbps. Conversely, files with decompression
rates below 64Kbps or over 192Kbps will not be played
properly.
- Do not try recording copyright protected MP3 files.
Certain "secured" files are encrypted and code protected to
prevent illegal copying. These files are of the following types:
TM
Windows Media (registered trade mark of Microsoft Inc) and
TM
SDMI (registered trade mark of The SDMI Foundation). You
cannot copy such files.
- Important:
The above recommendations cannot be taken as a
guarantee that the DVD player will play MP3 recordings, or as
an assurance of sound quality. You should note that certain
technologies and methods for MP3 file recording on CD-Rs
prevent optimal playback of these files on your DVD player
(degraded sound quality and in some cases, inability of the
player to read the files).
- This unit can play a maximum of 500 files and 500 folders
per disc.
20
MPEG4 Playback
MPEG4 Play Function
AVI files are used to contain the audio and video
data. Format files with the “.avi&DivX” extensions
can be played.
1. Open the disc tray. Place the disc on the tray.
Close the tray.
ƒ buttons to select an avi file
2. Press the œ/ƒ
(DivX/XviD), then press the ENTER button.
001/005
Off
Repeat Playback
Press the REPEAT button to change playback mode. There
are 4 modes, such as Off, Folder, Title an A-B.
-Folder : Repeats the AVI files which have the same exten
sion in the current folder.
-Title : repeats the title that is playing.
-A-B : repeats a segment of the file that you selecting.
MPEG4 Function Description
(
(
Function
Description
Reference page
Skip
or
During play, press the
or
button, it moves forward or
backward 5 minutes.
During play, press the SEARCH (
or
) button and press again to
search at a faster speed. Allows you
to search at a faster speed in an
AVI file. (2X, 4X, 8X)
Allows you to search at a slower
speed in an AVI file. (1/2X, 1/4X,
1/8X,1/16X)
Each time the STEP button is
pressed, a new frame will
appear.
-
)
Search
or
)
Slow Motion
Play
Step Motion
Play
-
P 14
P 14
- These functions may not work depending on MPEG4 file.
CD-R AVI file
This unit can play the following video compression formats
within the AVI file format:
- DivX 3.11 contents
- DivX 4 contents (Based on MPEG4 Simple Profile)
- DivX 5 contents (MPEG4 simple profile plus additional features such as bi-directional frames. Qpel and GMC are also
supported.)
- XviD MPEG4 compliant Contents.
This unit supports all resolutions up to maximum below.
DivX5
Zoom
Bitrate may fluctuate:
720 x 480 @30fps
Device may skip decoding the
720 x 576 @25fps
- Each time number 7 is pressed, the picture is
enlarged.
zoom mode : 100% -125%-150%-200%-100% .
high bitrate portions and begin
: Maximum bitrate : 4Mbps
Slide show
decoding again when Bitrate
returns to
normal.
Note
- Some MPEG4 files created on a personal computer may not be play back.
That is why Codec Type, Version and Higher resolution over specification is not supported.
- This unit supports CD-R/RW written in MPEG4 in
accordance with the “ISO9660 format”.
Picture CD Playback
1. Select the desired folder.
ƒ buttons to select a Picture file in the clips
2. Press the œ/ƒ
menu and then press the ENTER button.
Rotation
- Each time the ¦/‹button is pressed,the picture
rotates 90 degree clockwise.
- Each time the œ button is pressed,the picture
rotate 180 degree.
- When you press the ENTER/PLAY at JPEG file,it
will go to full screen mode and automaically slide
show.
Note
- Depending on a file size, the amount of time
between each picture may be different from the
manual.
- If you don’t press any button, the slide show will
start automatically in about 8 seconds by default.
CD-R JPEG Discs
- Only files with the “.jpg” and “.JPG” extensions can be played.
- If the disc is not closed, it will take longer to start playing and
not all of the recorded files may be played.
- Only CD-R discs with JPEG files in ISO 9660 or Joliet format
can be played.
- The name of the JPEG file may not be longer than 8
characters and should contain no blank spaces or special
characters (. / = +).
- Only a consecutively written multi-session disc can be played.
If there is a blank segment in the multi-session disc, the disc
can be played only up to the blank segment.
- A maximum of 500 images can be stored on a single CD.
- Kodak Picture CDs are recommended.
- When playing a Kodak Picture CD, only the JPEG files in the
pictures folder can be played.
- When playing a Kodak Picture CD, only the JPEG files in the
pictures folder can be played.
- Kodak Picture CD: The JPEG files in the pictures folder can
be played automatically.
- Konica Picture CD: If you want to see the Picture, select the
JPEG files in the clips menu.
- Fuji Picture CD: If you want to see the Picture, select the
JPEG files in the clips menu.
- QSS Picture CD: The unit may not play QSS Picture CD.
- If the number of files in 1 Disc is over 500, only 500 JPEG
files can be played.
- If the number of folders in 1 Disc is over 500, only JPEG
files in 500 folders can be played
- Each time the ƒ button is pressed,the picture
go to miror appearance.
21
English
DivX3.11 & DivX4 & XviD
KARAOKE
FUNCTIONS
CHANGING SETUP
MENU
Karaoke Functions
Using the Setup Menu
Operation Sequence
1. Connect the Mixed Audio Out terminals with the TV or
Amplifier. (see page 9 to 13)
2. Connect Mic into Mic jack. When a MIC is connected, the
karaoke functions can be used.
The Setup menu lets you customize your DVD player by allowing you to select various language preferences, set up a parental level, even adjust the player to the type of television screen you have.
1. Pess the MENU button on the remote control.Use the ¦/‹
buttons to select Setup, then press the ƒ or ENTER button.
.. L a n g u a g e
Player Menu
Disc Menu
Audio
Subtitle
Setup
ENG
ENG
ORI
AUTO
Page
. . ..
Key Control
1. Playback the Karaoke Disc containing the wanted songs.
Press the KARAOKE button.
‹ buttons to change the desired tone.
2. Press the ¦/‹
Key+ 00
❶ Language Setup page: Setup of the Language.
❷ Audio Setup page: Setup of the Audio Options.
❸ Display Setup page: Setup of the Display Options. Use
to select which type of screen you want to watch and
several display options.
❹ Parental Setup page: Setup of the Parental Level. Allows
users to set the level necessary to prevent children from
viewing unsuitable movies such as those with violence,
adult subject matter, etc.
❺ DivX(R) page : Please use the Registration code
Note
- If you hear feedback(squealing or howling) while
using the karaoke feature, move the microphone
away from the speakers or turn down the
microphone volume or the speaker volume.
- When playing MP3, WMA, DTS and LPCM disc,
the karaoke functions will not operate.
- When the MIC is connected, Digital Out does
not work.
- If the MIC is connected in VCD 2.0, Playback is
selected to Menu off mode automatically.
- The MIC sound outputs only from Analog Audio
Out.
22
to register this player with the DivX(R) Video On
Demand format. To learn more go to www.divx.com/vod.
2. Press the ¦/‹ buttons to access the different features.
Press the ƒ or ENTER button to access the sub features.
3. To make the setup screen disappear after setting up, press
the MENU button again.
Note
Depending on the disc, some Setup Menu selections may not work.
If you set the player menu, disc menu, audio and
subtitle language in advance, they will come up
automatically every time you watch a movie.
Using the Player Menu Language
1. Press the MENU button.
2. Press the ¦/‹ buttons to select Language Setup, then
press the ƒ or ENTER button.
ƒ buttons to select Player Menu, then press
3. Press the œ/ƒ
the ‹ or ENTER button.
ƒ buttons to select the desired language,
4. Press the œ/ƒ
then press ENTER button.
- The language is selected and the screen
returns to Language Setup page.
- To make the setup menu disappear, press the MENU
button.
Using the Audio Language
1. Press the MENU button.
2. Press the ¦/‹ buttons to select Language Setup page,
then press the ƒ or ENTER button.
ƒ buttons to select Audio, then press ENTER
3. Press the œ/ƒ
button.
ƒ buttons to select the desired language, then
4. Press the œ/ƒ
press ENTER button.
- Select “Original” if you want the default soundtrack
language to be the original language the disc is
recorded in.
- If the selected language is not recorded on the disc, the
original pre-recorded language is selected.
- The language is selected and the screen returns to
Language Setup menu.
- To make the setup menu disappear, press the MENU
button.
.. L a n g u a g e
.. L a n g u a g e
Player Menu
Disc Menu
Audio
Subtitle
Setup
ENG
ENG
ORI
AUTO
Page
English
Français
Deutsch
Español
Italiano
Nederlands
This function changes the text language only on the
disc menu screens.
1. Press the MENU button.
2. Press the ¦/‹ buttons to select Language Setup page,
then press the ƒ or ENTER button.
ƒ buttons to select Disc Menu, then press
3. Press the œ/ƒ
the ENTER button.
ƒ buttons to select the desired language,
4. Press the œ/ƒ
then press the ENTER button.
- The language is selected and the screen returns to
Language Setup page
- To make the setup menu disappear, press the MENU
button.
Setup
Page
Player Menu
ENG
Disc Menu
ENG
Audio
ORI
Subtitle
AUTO
. . ..
English
Français
Deutsch
Español
Italiano
Nederlands
Cesky
Dansk
Page
ENG
Disc Menu
ENG
Audio
ORI
Subtitle
AUTO
. . ..
Using the Disc Menu Language
.. L a n g u a g e
Setup
Player Menu
. . ..
Original
English
Français
Deutsch
Español
Italiano
Nederlands
Cesky
Using the Subtitle Language
1. Press the MENU button.
2. Press the ¦/‹ buttons to select Language Setup, then
press the ƒ or ENTER button.
ƒ buttons to select Subtitle, then press the ‹
3. Press the œ/ƒ
or ENTER button.
ƒ buttons to select the desired language,
4. Press the œ/ƒ
then press the ENTER button.
- Select “Automatic” if you want the subtitle language to
be the same as the language selected as the audio
language.
- Some discs may not contain the language you select as
your initial language; in that case the disc will use its
original language setting.
- The language is selected and the screen returns to
setup menu.
- To make the setup menu disappear, press the MENU
button.
.. L a n g u a g e
Setup
Page
Player Menu
IND
Disc Menu
ENG
Audio
ORI
Subtitle
AUTO
. . ..
Automatic
English
Français
Deutsch
Español
Italiano
Nederlands
Cesky
23
English
Setting Up the Language
Features
Using the DivX Subtitle Language
1. Press the MENU button.
2. Press the ¦/‹ buttons to select DivX Page, then press
the ƒ or ENTER button.
ƒ buttons to select DivX Subtitle, then press
3. Press the œ/ƒ
the ‹ or ENTER button.
ƒ buttons to select the desired language,
4. Press the œ/ƒ
then press the ENTER button.
- The language is selected and the screen returns to
Language Setup menu.
- To make the setup menu disappear, press the
Setting Up the Audio
Options
Audio Options allows you to setup the audio device
and sound status settings depending on the audio
system in use.
1. Press the MENU button.
2. Press the ¦/‹ buttons to select Audio Setup, then
press the ƒ or ENTER button.
ƒ buttons to select the desired item, then
3. Press the œ/ƒ
press the ‹ or ENTER button.
MENU button.
.. DivX Page..
Divx Subtitle
Divx VOD
Western
Western
Central
Cyrillic
Greek
Turkish
Arabic
.. Audio Setup Page ..
Dolby Digital Out
MPEG2 Digital Output
Dynamic Compression
PCM Down Sampling
.. Audio Setup Page ..
Dolby Digital Out
MPEG2 Digital Output
Dynamic Compression
PCM Down Sampling
PCM
PCM
On
On
PCM
PCM
On
On
PCM
BItstream
Using the DivX VOD
1. With the unit in stop mode, press the menu butoon.
2. Press the ¦/‹ button to select DivX Page, then
press the ƒ or ENTER.button
ƒbutton to select DivX VOD, then
3. Press the œ/ƒ
press the ‹ or ENTER .button.
4. Press OK to see the DivX registrasion number.
DivX(R) Video on demand
your registration code is:
XR3YJ4HZ
http://www.divx.com/vod
OK
Note
- If you press ok will make the setup menu dissa
pear.
OK
- Divx VoD item only can acces at stop mode.
❶ Dolby Digital Out
- PCM : Converts to PCM(2CH) audio.
- Bitstream : Outputs Dolby Digital via the digital out
put.Select Bitstream when connecting to a
Dolby Digital Decoder.
❷ MPEG-2 Digital Out
- PCM : Converts to PCM(2CH) audio.
- Bitstream : Converts to MPEG-2 Digital Bitstream
(5.1CH or 8CH). Select Bitstream when using the
Digital Audio Output.
❸ Dynamic Compression
- On : To select dynamic compression.
- Off : To select the standard range.
❹ PCM Down Sampling
- On : Select this when the Amplifier connected to the
player is not 96KHz compatible. In this case, the
96KHz signals will be down converted to 48KHZ.
- Off : Select this when the Amplifier connected to the
player is 96KHz compatible. In this case, all sig
nals will be output without any changes.
Note
Even when PCM Down sampling is Off
• Some discs will only output down sampled
audio through the digital outputs.
• To make the Setup menu disappear, press the
MENU button.
24
❷ Screen Message
Use to turn on-screen messages On or Off.
❸
Video Output
Select Video Output.
- I-SCAN: Select when you want to use
Component Interlace (525i) Out.
“DTS” and “DTS Digital Out” are trademarks of
Digital Theater Systems, Inc.
- P-SCAN: Select when you want to use
Component Progressive (525p) Out.
Setting Up the Display
Options
• If you press the VIDEO SEL. button, Video
output mode is changed in regular sequence
in no disc mode. (I-SCAN ➝ P-SCAN).
Display options enable you to set various video
functions of the player.
1. Press the MENU button.
2. Press the ¦/‹ buttons to select Display Setup page
then press the ƒ or ENTER button.
ƒ buttons to select the desired item, then
3. Press the œ/ƒ
press the ‹ or ENTER button.
.. Display Setup Page ..
Tv Aspect
LB
Screen Message
On
Video Output
I-Scan
Black Level
Off
TV System
PAL
❹
P-SCAN
I-SCAN
Black Level
Adjusts the brightness of the screen.(On or Off) It does
not function in Progressive mode.
➎ TV System
❶ TV Aspect
Depending on a type of television you have, you
may want to adjust the screen setting (aspect
ratio).
- 4:3 Pan&Scan : Select this for conventional
size TVs when you want to see the central portion of the 16:9 screen. (Extreme left and right
side of movie picture will be cut off.)
- 4:3 Letter Box : Select when you want to see
the total 16:9 ratio screen DVD
supplies, even though you have a TV with a 4:3
ratio screen. Black bars will appear at the top
and bottom of the screen.
- 16:9 Wide : You can view the full 16:9
picture on your wide screen TV.
.. Display Setup Page ..
Tv Aspect
LB
Screen Message
On
Video Output
I-Scan
Black Level
Off
TV System
PAL
.. Display Setup Page ..
Tv Aspect
LB
Screen Message
On
I-Scan
Off
PAL
Video Output
Black Level
TV System
4:3 Pan&Scan
4:3 letter Box
16:9 Wide
- NTSC : In case of using NTSC disc
• If your TV system only has PAL-Video input,
you must choose “PAL”. When you choose
“PAL”, Interlace output format is PAL 60 Hz
output.
• If your TV system only has NTSC, input you
must choose “NTSC ”.
• If you set up the NTSC TV system
- PAL : In case of using PAL disc
• If your TV system only has NTSC-Video input,
you must choose “NTSC”.
• If your TV system only has PAL input, you
must choose “PAL ”.
• If you set up the PAL TV system.
.. Display Setup Page ..
Tv Aspect
LB
Screen Message
On
Video Output
I-Scan
Black Level
Off
TV System
PAL
PAL
AUTO
NTSC
• Consult your TV User’s Manual to find
out if your TV supports Progressive Scan. If
Progressive Scan is supported, follow the TV
User’s Manual regarding Progressive Scan
settings in the TV’s menu system.
• If Video Output is set incorrectly, the screen
may be blocked.
• When the resolution is changed during playback, it may take a few seconds for a normal
image to appear.
25
English
Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D symbol
are trademarks of Dolby Laboratories.
Note
Setting Up the Parental
Control
❶ KID SAFE
❷ G(General Audiences) : All Ages Admitted
❸ PG(Parental Guidance suggested): Some material may
The Parental Control function works in conjunction
not be suitable for young children.
with DVDs that have been assigned a rating, which ❹ PG-13 (PG-13-Parents strongly cautioned) : Some material
helps you control the types of DVDs that your family may be inapproriate for children under 13
watches. There are up to 8 rating levels on a disc. ❺ PGR ( parental guidance Recommended): These are not
necessarily unsuitable for children, but viewer discretion is
Setting Up the Rating Level
advised, and parents and guardians are encouraged to
supervise younger viewers.
❻
1. Press the MENU button.
R( Restricted): Under 17 requires accompanying adult
❼ NC17( NC-17) : No one 17 and under admitted
❽ Adult
2. Press the ¦/‹ buttons to select parental setup page,
Note
then press the ƒ or ENTER button.
• To make the setup menu disappear, press the
MENU button. For example.
.. P a r e n t a l P a g e . .
Parental
Password
Changing the Password
1. Press the MENU button.
ƒ buttons to select Parental, then press
3. Press the œ/ƒ
‹ or ENTER button.
the 2. Press the ¦/‹ buttons to select parental setup page,
then press the ƒ or ENTER button.
ƒ buttons to select the Rating Level you want,
4. Press the œ/ƒ
then press the ENTER button.
e.g) Setting up in KID SAFE
.. P a r e n t a l P a g e . .
Parental
1 KID SAFE
2G
Password
3 PG
4 PG 13
5 PGR
6R
7 NC17
8 ADULT
.. P a r e n t a l P a g e . .
Parental
Password
ƒ buttons to select PASSWORD, then
3. Press the œ/ƒ
press the ‹ or ENTER button.
.. P a r e n t a l P a g e . .
Parental
Password
OK
5. Enter your password.
- By default, password is set to 0000.
4. The Enter password screen appear. Enter your pasword
(default password), Enter the new password again
Sandi
Password
OK
Cancel
.. P a r e n t a l P a g e . .
Parental
Change
Password
26
English
Note
If you have forgotten your password, see
“Forgot Password” in the Troubleshooting Guide.
27
REFERENCE
Firmware upgrade
Introduction
Samsung will often support the software upgrade
to improve the performance of this unit to the
lastest status , trough samsung Internet
Site(www.samsung.com)
2.Press enter or play to start upgrade.
- Other key to cancel upgrade back to samsung logo and eject the disc.
Upgrade file detected
Curent version: 07.12.15.00
Upgrade ?
Press Play to start
File copying
Firmware upgrade Start
Because the specially new mpeg4 codec continuse and it is appearing.What improvements are
made depends on the upgrade software your are
using as well as the software that your DVD-player contained before the upgrde.
Upgrade file detected
Curent version: 07.12.15.00
Upgrade ?
Press Play to start
Upgrade
Firmware upgrade Start
How to make an upgrade disc
Write the downloaded file onto a blank CD-R or CDRW disc, using the following settings:
- In the middle of the writing, the tray will open
automatically. After taking out the disc, please
wait for about 2 minutes.
- If the unit was succesfully update, the unit will
turn off and on after closing the tray automatically.
When the unit turns on, this screen will display.
1. You have to download a new file trough Download
center of Samsung Internet Site (http://www.sam
sung.com).
3.Press the number buttons to select the
desired language
2. Write the file to disc using CD-RW driver of your
SELECT MENU LANGUAGE
computer.
Note
- File system CD-ROM
- Chracteer set ISO 9660
- Finalized, single session
- Write speed low
Note
Update procedure
1.Open the disc tray. Place disc the on the tray.
close the tray. The Firm ware Upgrade sreen
appears.
Upgrade file detected
Curent version: 07.12.15.00
Upgrade ?
Press Play to start
Firmware upgrade
Appears
28
Press
1
Touche
2
Drücken Sie
3
for English
für Deutsch
Pulsar
4
para Español
Premere
5
per Italiano
Druk op
6
voor Nederlands
pour Français
- If the “Select Menu Language”doesn’t appear,
please contact to “Samsung Service Center- If
the unit was succesfully update, the unit will
turn off and on after closing the tray automatical
- Do not press any button and plug the power code
during upgrade.
- The upgrade procedure may change, refer to the
web site( www.samsung.com)
Troubleshooting
Before requesting service (troubleshooting), please check the following.
Page
No operations can be
performed with the
remote control.
• Check the batteries in the remote control.
They may need replacing.
• Operate the remote control at a distance of no more than 20 feet.
• Remove batteries and hold down one or more buttons for several minutes to drain
the microprocessor inside the remote control to reset it. Reinstall batteries and try
to operate the remote control again.
P3
Disc does not play.
• Ensure that the disc is installed with the label side facing up.
• Check the region number of the DVD.
P5
5.1 channel sound is
not being reproduced.
The
icon appears
on screen.
• 5.1 channel sound is reproduced only when the following conditions are met. :
1) The DVD player is connected with the proper Amplifier
2) The disc is recorded with 5.1 channel sound.
• Check whether the disc being played has the “5.1 ch” mark on the outside.
• Check if your audio system is connected and working properly.
• In a SETUP Menu, is the Audio Output set to Bitstream?
• The features or action cannot be completed at this time because:
1. The DVD’s software restricts it.
2. The DVD’s software doesn’t support the feature (e.g., angles).
3. The feature is not available at the moment.
4. You’ve requested a title or chapter number or search time that is out of range.
English
Action
Problem
P12-13
P24-25
Disc Menu doesn’t appear. • Check if the disc has a Menu.
Play mode differs from the
Setup Menu selection.
• Some of the functions selected in the Setup Menu may not work properly if the
disc is not encoded with the corresponding function.
The screen ratio
cannot be changed.
• The Screen Ratio is fixed on your DVDs.
No audio.
• Make sure you have selected the correct Digital Output in the Audio Options
Menu.
The screen is blocked
• Press the
P25
P24-25
button (in front panel) for more than 5 seconds under no disc
inside. All settings will revert to the factory settings.
Forgot password
P22-27
• Press the
button (in front panel ) for more than 5 seconds
under no disc inside. All settings including the password will revert to the factory
settings. Don't use this unless absolutely necessary.
If you experience
other problems.
• Go to the contents and find the section of the instruction book that contains the
explanations regarding the current problem, and follow the procedure once again.
• If the problem still cannot be solved, please contact your nearest authorized service center.
The picture is noisy or
distorted
• Make sure that the disc is not dirty or scratched.
• Clean the disc.
P14
P26
P2
29
Specifications
General
Power Requirements
AC 110-240 V, 60/50 Hz
Power Consumption
9W
1.3 Kg
Weight
360mm (W) X 200mm (D) X 37mm (H)
Dimensions
+5°C to +35°C
Operating Temperature Range
Operating Humidity Range
10 % to 75 %
DVD
(DIGITAL VERSATILE DISC)
Disc
Reading Speed : 3.49 ~ 4.06 m/sec.
Approx. Play Time
(Single Sided, Single Layer Disc) : 135 min.
CD : 12Cm
(COMPACT DISC)
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 74 min.
CD : 8Cm
(COMPACT DISC)
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 20 min.
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 74 min. (Video + Audio)
VCD : 12Cm
Video
Output
Composite Video
1 channel : 1.0 Vp-p (75 Ω load)
Component Video
Y : 1.0 Vp-p (75 Ω load)
Pr : 0.70 Vp-p (75 Ω load)
Pb : 0.70 Vp-p (75 Ω load)
2 Channel
Audio
Output
L(1/L), R(2/R)
48 kHz Sampling : 4 Hz to 22 kHz
96 kHz Sampling : 4 Hz to 44 kHz
*Frequency Response
*S/N Ratio
110 dB
*Dynamic Range
100 dB
*Total Harmonic Distortion
0.004 %
*: Nominal specification
- Samsung Electronics Co., Ltd reserves the right to change the specifications without
notice.
- Weight and dimensions are approximate.
30
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer
care center.
Region
North America
Latin America
Country
CANADA
MEXICO
U.S.A
ARGENTINE
BRAZIL
CHILE
NICARAGUA
HONDURAS
COSTA RICA
ECUADOR
EL SALVADOR
GUATEMALA
JAMAICA
PANAMA
PUERTO RICO
REP. DOMINICA
TRINIDAD & TOBAGO
VENEZUELA
COLOMBIA
BELGIUM
CZECH REPUBLIC
DENMARK
FINLAND
FRANCE
Europe
CIS
Asia Pacific
Middle East &
Africa
GERMANY
HUNGARY
ITALIA
LUXEMBURG
NETHERLANDS
NORWAY
POLAND
PORTUGAL
SLOVAKIA
SPAIN
SWEDEN
U.K
EIRE
AUSTRIA
SWITZERLAND
RUSSIA
KAZAHSTAN
UZBEKISTAN
KYRGYZSTAN
TADJIKISTAN
UKRAINE
LITHUANIA
LATVIA
ESTONIA
AUSTRALIA
NEW ZEALAND
CHINA
HONG KONG
INDIA
INDONESIA
JAPAN
MALAYSIA
PHILIPPINES
SINGAPORE
THAILAND
TAIWAN
VIETNAM
TURKEY
Customer Care Center 1-800-SAMSUNG(726-7864)
01-800-SAMSUNG(726-7864)
1-800-SAMSUNG(726-7864)
0800-333-3733
0800-124-421 , 4004-0000
800-SAMSUNG(726-7864)
00-1800-5077267
800-7919267
0-800-507-7267
1-800-10-7267
800-6225
1-800-299-0013
1-800-234-7267
800-7267
1-800-682-3180
1-800-751-2676
1-800-SAMSUNG(726-7864)
0-800-100-5303
01-8000112112
0032 (0)2 201 24 18
844 000 844
Distributor pro Českou republiku:
Samsung Zrt., česka organizační složka
Vyskočilova 4, 14000 Praha 4
70 70 19 70
030-6227 515
3260 SAMSUNG ( 0,15/Min),
08 25 08 65 65 ( 0,15/Min)
01805 - SAMSUNG(726-7864) (
06-80-SAMSUNG(726-7864)
800-SAMSUNG(726-7864)
0035 (0)2 261 03 710
Web Site
www.samsung.com/ca
www.samsung.com
www.samsung.com
www.samsung.com/ar
www.samsung.com
www.samsung.com/cl
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com.co
www.samsung.com/be
www.samsung.com/cz
www.samsung.com/dk
www.samsung.com/fi
www.samsung.com
0,14/Min)
0900-SAMSUNG(726-7864) ( 0,10/Min)
815-56 480
0 801 801 881 , 022-607-93-33
80820-SAMSUNG(726-7864)
0800-SAMSUNG(726-7864)
902 10 11 30
0771-400 200
0845 SAMSUNG (7267864)
0818 717 100
0800-SAMSUNG(726-7864)
0800-SAMSUNG(726-7864)
8-800-555-55-55
8-10-800-500-55-500
8-10-800-500-55-500
00-800-500-55-500
8-10-800-500-55-500
8-800-502-0000
8-800-77777
800-7267
800-7267
1300 362 603
0800SAMSUNG(726-7864)
800-810-5858 , 010-6475 1880
3698-4698
3030 8282 , 1800 110011
0800-112-8888
0120-327-527
1800-88-9999
1800-10-SAMSUNG(726-7864)
1800-SAMSUNG(726-7864)
1800-29-3232 , 02-689-3232
0800-329-999
1 800 588 889
444 77 11
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com/be
www.samsung.com/nl
www.samsung.com/no
www.samsung.com/pl
www.samsung.com/pt
www.samsung.com/sk
www.samsung.com
www.samsung.com/se
www.samsung.com
www.samsung.com/ie
www.samsung.com/at
www.samsung.com/ch
www.samsung.com
www.samsung.kz
www.samsung.uz
www.samsung.com
www.samsung.lt
www.samsung.com/lv
www.samsung.ee
www.samsung.com
www.samsung.com/nz
www.samsung.com
www.samsung.com/hk
www.samsung.com
www.samsung.com
www.samsung.com/jp
www.samsung.com/my
www.samsung.com/ph
www.samsung.com
www.samsung.com
www.samsung.com/tw
www.samsung.com
www.samsung.com
SOUTH AFRICA
0860-SAMSUNG(726-7864 )
www.samsung.com
U.A.E
800-SAMSUNG (726-7864), 8000-4726
www.samsung.com
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products,
please contact the SAMSUNG customer care centre.
☎1800-88-9999/www.samsung.com/my
AK68-01640B
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement