Samsung | HG32AD590HW | Samsung HG40AD590BK User Manual

LED TV
Installation manual
Thank you for purchasing Samsung product.
To receive more service, please register your
product at
www.samsung.com/register
Model
Serial No.
Figures and illustrations in this User Manual are provided for reference only and may differ from actual product
appearance. Product design and specifications may be changed without notice.
Instruction
This TV is provided with interactive functionality through a set-back box (SBB/STB) connected to the TV, and with other TVs in a computercontrolled system for hotels and other hospitality businesses.
Interactive: When the TV is powered-up initially, it sends a command to identify the SBB/STB; if identified, theTV switches to ONLINE mode
and full control is through the SBB/STB.
If the TV is in ONLINE mode, it stops receiving IR(Samsung remote) commands and acts according to interface protocol.
Stand-Alone: If SBB/STB is not identified, the TV should be switched to STAND-ALONE mode with restricted operation.
Operational Modes
When this TV (in Hotel mode) is operated with a SBB/STB, it is in one of two states :
•ONLINE or STAND-ALONE. In the STAND-ALONE state, the TV will act as a Hotel TV, but without active communication. This is to prevent
guests from trying to cheat the system by disconnecting the SBB/STB.
Hotel Mode On
Hotel TV
SBB/STB Online if
one success within
10 attempts
Stand-alone
Mode
SBB/STB
Online-10
consecutive
fails
Power
ON
SBB/STB
StatusAttempt
every 2secs
Online Mode
Poll Rate 20/sec
To set the details for Stand-alone or interactive mode, refer to pages 17-20 (Setting the hotel option data : Stand-alone mode and Interactive
mode)
•Some operations may be restricted to prevents guests from "cheating" the TV system.
• No main menu(Interactive mode) or Channel Menu, Plug & Play in Main Menu (Stand-Alone mode)
•Limited Volume and Panel key lock or unlock
Still image warning
Avoid displaying still images (like jpeg picture files) or still image element (like TV Program logo, panorama or 4:3 image format, stock or news
bar at screen bottom etc.) on the screen. Constant displaying of still picture can cause uneven wear of screen phosphor, which will affect
image quality. To reduce risk of this effect, please follow below recommendations:
•Avoid displaying the same TV channel for long periods.
•Always try do display any image on full screen, use TV set picture format menu for best possible match.
•Reduce brightness and contrast values to minimum required to achieve desired picture quality, exceeded values may speed up the burnout
process.
•Frequently use all TV features designed to reduce image retention and screen burnout. Refer to the relevant user manual section for details.
Securing the Installation Space
Keep required distances between the product and other objects (e.g. walls) to ensure proper ventilation.
Failing to do so may result in fire or a problem with the product due to an increase in the internal temperature.
✎✎ When using a stand or wall-mount, use parts provided by Samsung Electronics only.
•Using parts provided by another manufacturer may result in a problem with the product or injuries due to the product falling.
✎✎ The appearance may differ, depending on the product.
Installation with a stand.
Installation with a wall-mount.
10 cm
10 cm
10 cm
10 cm
10 cm
10 cm
10 cm
Contents
yy Installing the LED TV Stand....................................................................................................................... 5
yy Viewing the Connection Panel................................................................................................................... 6
yy Viewing the Remote Control...................................................................................................................... 10
yy Connecting the MediaHub HD.................................................................................................................. 14
yy Connecting the RJP (Remote Jack Pack).................................................................................................. 15
yy Setting the Hotel Option Data................................................................................................................... 17
yy Installing the Wall Mount........................................................................................................................... 56
yy Securing the TV to the Wall....................................................................................................................... 57
yy Anti-theft Kensington Lock........................................................................................................................ 57
yy Specifications........................................................................................................................................... 58
yy Dimensions............................................................................................................................................... 59
yy Licence..................................................................................................................................................... 62
English
3
ENGLISH
yy Accessories.............................................................................................................................................. 4
Accessories
✎✎ Please make sure the following items are included with your LED TV. If any items are missing, contact your dealer.
✎✎ The items’ colour and shapes may vary depending on the model.
• Remote Control & Batteries (AAA x 2)
• Quick Set up Guide
• Cable Holder
• Power Cord / Data Cable
• Owner’s Instructions
Safety Guide (Not available in all locations)
✎✎ The stand and stand screw may not be included, depending on the model.
✎✎ The Data Cable may not be included, depending on the SI Vendor.
4
English
Installing the LED TV Stand
Stand Components
When installing the stand, use the provided components and parts.
B 1 EA
A 1 EA
32"
x8 (M4 X L12)
40"
x4 (2ea)
(M4 X L14)
C
32"
40"
32"
Stand
40"
Guide Stand
Screws
HG32AD590 / HG40AD590
1
C
32"
Top View
x4 (M4 X L12)
40"
C
x4 (M4 X L14)
B
B
A
Front
Front
A
ATTENTION
Rear
DO NOT USE
CHEMICALS
2
Rear
DO NOT USE DO NOT USE
GREASE
OIL
✎✎ Place a soft cloth over
the table to protect the
TV, and then place the
TV on the cloth screen
side down.
✎✎ Insert the Stand Guide
into the slot on the
bottom of the TV.
(Correct assembly)
Side View
(Incorrect assembly)
3
C
32"
40"
x4 (M4 X L12) x4 (M4 X L14)
4
When the declination
happened, try reassemble
it 2 category.
✎✎ Make sure to
assembling stand guide
attached on the TV.
✎✎ Progress the assembly of screw in the
manual’s order.
✎✎ NOTE
• Make sure to distinguish between the front and back of each component when assembling them.
• Make sure that at least two persons lift and move the TV.
English
5
Viewing the Connection Panel
2
2
3
3
4
4
HG32AD590
1
1
5
5
6 7
6 7
2
4
0
2
4
0
8
8
1
9
9
0
0
3
1
3
HG40AD590
7
67
6
5
5
8
8
9
9
✎✎ Whenever you connect an external device to your TV, make sure that power on the unit is turned off.
✎✎ When connecting an external device, match the colour of the connection terminal to the cable.
6
English
1USB (HDD 5V 0.5A) / CLONING, USB (5V 0.5A) / CLONING
−− Connector for software upgrades and Media Play, etc.
−− Service connection.
2RJP
This port is an RJP (Remote Jack Pack) communication port that enables connecting different devices to additional
modules to improve device use and convenience.
3HDMI IN 1(DVI), 2(ARC)
Connects to the HDMI jack of a device with an HDMI output.
✎✎ No sound connection is needed for an HDMI-HDMI connection. HDMI connections carry both audio and video.
✎✎ Use the HDMI IN 1(DVI) jack for a DVI connection to an external device. Use a DVI to HDMI cable or DVI-HDMI
adapter (DVI to HDMI) for the video connection and the PC/DVI AUDIO IN jacks for audio.
4DATA
−− Used to support data communication between the TV and the SBB.
−− Connects using RJ-12 TV type plugs.
5ANT IN
−− To view television channels correctly, the TV must receive a signal from one of the following sources:
−− An outdoor antenna / A cable television system
6HEADPHONE JACK
Headphones may be connected to the headphone jack on your TV. While the headphones are connected, the sound
from the built-in speakers is disabled.
7HP-ID
Connect the cable to HP-ID and Headphone Jack simultaneously and connect it to separated Headphone Box. See
page 14. When connecting Headphone to Headphone Box, it works same as Headphone function.
8PC/ DVI AUDIO IN
Connects to the audio input jacks on an Amplifier/Home Theater.
9PC IN
Connect to the video output jack on your computer.
0LAN
Connect to a wired LAN using CAT 7 cable.
English
7
Display Modes
You can also select one of the standard resolutions listed in the Resolution column. The TV will automatically adjust to the
resolution you choose.
After connecting a computer to the TV, set the screen resolution for the TV on the computer. The optimal resolution is 1920
x 1080 @ 60 Hz. If it is set to any other than in the table below, the TV may display nothing. Set the resolution properly,
referring to the user guide of the computer or its graphic card.
The resolutions in the table are recommended.
✎✎ Optimal resolution is 1920 X 1080 @ 60 Hz.
Mode
Resolution
Horizontal Frequency
(KHz)
Vertical Frequency
(Hz)
Pixel Clock
Frequency
(MHz)
Sync Polarity
(H / V)
IBM
720 x 400
31.469
70.087
28.322
-/+
MAC
640 x 480
832 x 624
1152 x 870
35.000
49.726
68.681
66.667
74.551
75.062
30.240
57.284
100.000
-/-/-/-
VESA DMT
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
1024 x 768
1024 x 768
1024 x 768
1152 x 864
1280 x 1024
1280 x 1024
1280 x 720
1280 x 800
1280 x 960
1366 x 768
1440 x 900
1600 x 900RB
1680 x 1050
1920 x 1080
31.469
37.861
37.500
37.879
48.077
46.875
48.363
56.476
60.023
67.500
63.981
79.976
45.000
49.702
60.000
47.712
55.935
60.000
65.290
67.500
59.940
72.809
75.000
60.317
72.188
75.000
60.004
70.069
75.029
75.000
60.020
75.025
60.000
59.810
60.000
60.015
59.887
60.000
59.954
60.000
25.175
31.500
31.500
40.000
50.000
49.500
65.000
75.000
78.750
108.000
108.000
135.000
74.250
83.500
108.000
85.500
106.500
108.000
146.250
148.500
-/-/-/+/+
+/+
+/+
-/-/+/+
+/+
+/+
+/+
+/+
-/+
+/+
+/+
-/+
+/+
-/+
+/+
✎✎ When using an HDMI/DVI cable connection, you must use the HDMI IN 1(DVI) jack.
✎✎ The interlace mode is not supported.
✎✎ The set might operate abnormally if a non-standard video format is selected.
✎✎ Separate and Composite modes are supported. SOG is not supported.
8
English
TV Controller
TV Controller is a multi directional button that helps navigate without using the remote control.
✎✎ Some functions which require a PIN code may not be available.
✎✎ The product colour and shape may vary, depending on the model.
✎✎ Exits the menu when pressing the controller for more than 1 second.
✎✎ When selecting the function by moving the controller to the up/down/left/right directions, do not press the controller. If
the controller is used first, you cannot operate it to move the up/down/left/right directions.
Function menu
TV Controller
The image is drawn by facing the
front side of the TV.
Remote control sensor
Power on
Turn the TV on by pressing the controller in standby mode.
Adjusting the volume
Adjust the volume by moving the controller from side to side when the power is on.
Selecting a channel
Select a channel by moving the controller up and down when the power is on.
Using the function menu
Press the controller when the power is on and the function menu appears. If you
press it again, the function menu screen disappears.
Using the Menu
Selects the MENU(m) by moving the controller in the function menu screen. The
OSD(On Screen Display) of your TV’s feature appears.
Selecting the Source
Selects the Source(s) by moving the controller in the function menu screen. The
Source list screen appears.
Selecting the SMART HUB
(™)
With the Function menu visible, select SMART HUB (™) by moving the Controller
upwards. The SMART HUB main screen appears. Select an application by moving
the Controller, and then pressing the Controller.
Power Off
Selects the Power Off(P) to turn the TV off by moving the controller in the function
menu screen.
✎✎ To close the Menu, SMART HUB, or Source, press the Controller for more than 1 second.
Standby mode
Do not leave your TV in standby mode for long periods of time a small amount of electric power is still consumed even when
the power button is such as when on holiday. off. It is best to unplug the power cord.
English
9
Viewing the Remote Control
✎✎ This remote control has Braille points on the Power, Channel, and Volume buttons and can be used by visually
impaired persons.
SOURCE
Turns the TV on and off.
−− Display and select available video
sources.
Have direct access to channels.
GUIDE
Alternately selects Teletext, Double
or Mix.
Electronic Programme Guide (EPG)
display.
Cut off the sound temporarily.
Change channels.
Adjust the volume.
Display channel list on the screen.
Switch to the HOME Screen.
HOME
Display the main on-screen menu.
CONTENT
CLOCK
Quickly select frequently used
functions.
Select on-screen menu items and
change menu values.
View the Contents Home.
Press to display information on the
TV screen.
CLOCK: When you press INFO key
in standby mode, TV screen displays
the time.
Exit the menu.
Return to the previous menu.
Buttons in the Channel list,
Contents Home menu, etc.
ALARM: Enter the hour you want the
TV to turn on.
X: Turns the 3D image on or off.
( Not available )
SUBT.: Displays digital subtitles.
10
English
ALARM
Use these buttons in the Contents
Home.
Installing batteries (Battery size: AAA)
X
Y
Z
✎✎ NOTE
• Use the remote control within 7m of the TV.
• Bright light may affect the performance of the remote control. Avoid using nearby special fluorescent light or neon
signs.
• The colour and shape may vary depending on the model.
• Remote control button 'HOME' & '3D' are not supported. When pressing these buttons, the TV unit does not
respond.
English
11
Connecting the TV with SBB
TV Rear Panel
ETH MODEM
Data Cable
1. Connect the DATA jack of the TV to the [ETH MODEM] jack of the STB (SBB) with the Data cable.
✎✎ Use data communication.
List of Vendors and Compatible Data Cables Supplied with the TV
• Confirm that you are using the correct data cable for your vendor. Refer to the code label on the data cables.
6
1
TV SIDE
STB SIDE
1
6
CON A
CON B
CON A
6: NC
5: IR
4: GND
3: Rx
2: Tx
1: Nc
12
English
CON A
CON B
5
6
4
2
3
5
2
3
CON B
1: NC
2: GND
3: Rx
4: NC
5: Tx
6: IR
Audio Loop In
An additional Headphone Box can be installed on a bed or business desk for added convenience. The installation
procedures are given below.
• Detailed Drawing of the Headphone Box.
TV Rear Panel
HEADPHON BOX
Headphone Box
Shield wire
TV Headphones jack
Red Wire (Audio-R)
Whitewire (Audio-L)
Red wire + White wire
Shield Wire
TV HP-ID jack
<Headphone Box>
English
13
Connecting the MediaHub HD
Output to any external source connected to MediaHub HD on the hotel desk.
MediaHub HD Rear
HDMI
USB
RS/232
TV Rear Panel
1 RS-232
Data Cable
2 HDMI cable
1. Connect the RJP port of the TV and the RS/232 port of the MediaHub HD.
2. Connect the HDMI IN 1(DVI), 2(ARC) port of the TV and the HDMI port of the MediaHub HD.
• MediaHub HD
−− The MediaHub HD is a hardware module that has different Audio Video inputs (A/V, Audio, PC, HDMI and USB)
and corresponding outputs. The corresponding output sources connect from MediaHub to the TV. MediaHub
communicates with the TV via RS232. Hot Plug & Play is a function that allows hotel guests to connect an external
source to the MediaHub. MediaHub communicates with the TV by sending messages regarding Active/Inactive
sources. The TV switches to the Active external source.
−− You have to connect the HDMI of the MediaHub to the HDMI IN 1(DVI) port of the TV.
−− When the TV is on, connect the TV and the RJP within 10 seconds.
• Special features
−− PIP
−− Auto Detection
14
English
Connecting the RJP (Remote Jack Pack)
Output to any external source connected to RJP on the hotel desk.
RJP Rear
USB
HDMI
VIDEO AUDIO AUDIO/PC
RS/232
3
TV Rear Panel
2 HDMI cable
1 D-sub / PC Audio cable
1. Connect the PC IN / PC/DVI AUDIO IN port of the TV to the PC/AUDIO port of the RJP.
2. Connect the HDMI IN 1(DVI), 2(ARC) port of the TV and the HDMI port of the RJP.
3. Connect the RJP port of the TV and the RS/232 port of the RJP.
✎✎ The RJP (Remote Jack Pack) compatible with this Samsung TV is TeleAdapt TA-7610, TA-7650 (HD) and TA-7660
(HD Plus).
• RJP (Remote Jack Pack): RJP stands for Remote Jack Pack. The RJP is a hardware module that has different Audio
Video inputs (A/V, Audio, PC and HDMI) and corresponding outputs. The corresponding output sources are connected
from RJP to TV. The RJP communicates with the TV via RS232. Hot Plug & Play is a function that allows hotel guests
to connect an external source to the RJP. The RJP communicates with the TV by sending messages regarding Active/
Inactive sources. The TV will switch to the Active external source according to the priority set by the User.
✎✎ You can select HDMI IN 1(DVI), 2(ARC) and AV IN for connecting RJP.
✎✎ When the TV is on, connect the TV and the RJP within 10 seconds.
English
15
• The RJP can be returned to the factory default settings by pressing the A/V and HDMI buttons simultaneously for 10
seconds. All LEDs blink 5 times to acknowledge that this has been finished.
• The RJP will automatically turn off any LEDs after 5 minutes to avoid unnecessary light pollution in the hotel room. The
LEDs that were turned off will turn on again if the guest touches any of the buttons and the 5 minute timer will restart. If
the guest then touches another source button, the TV will change to the selected source and the corresponding LED will
be lit.
• After an RJP Reset or a TV Power OFF/ON, it takes approx. 10 seconds to establish communications between the TV
and the RJP.
• The following table shows the approximate time in seconds to switch from the TV to the input source, based on the
priority.
✎✎ Scenario 1: When no inputs are connected.
Source
To Connect
AV
PC
HDMI
2 Sec
0.7 Sec
3.9 Sec
✎✎ Scenario 2: When two or more inputs are connected and an Input source is disconnected and then reconnected.
Source
Disconnect
To Connect
Total
AV
PC
HDMI
4.5 Sec
0.7 Sec
3.9 Sec
2 Sec
0.7 Sec
3.9 Sec
6.5 Sec
1.4 Sec
7.8 Sec
✎✎ E.g. If the RJP has all its live sources AV, PC and HDMI connected, AV is viewed as the highest priority. If the RJP is
in HDMI mode, and a guest removes and reconnects the AV, the minimum time required to switch to the AV is 6.5
seconds.
• To connect audio (Ipod or Mp3), Music mode should be ON and Jack Ident detect should be OFF.
• A/V, PC and HDMI input sources are supported.
16
English
Setting the Hotel Option Data
To Enter: Press the MUTE → 1 → 1 → 9 → ENTERE buttons in order. (From the Hospitality mode, the Standalone mode is set.)
To Exit from this menu : power off and turn on again.
✎✎ Depending on Model and Region, some menus do not exist on the TV set.
Hotel TV Function
Category
Item
Hospitality
Mode
Hospitality Mode
SI Vendor
SI Vendor
Power On
Description
Select Hospitality mode.
•Interactive mode : TV works with an SI STB or SBB.
•Standalone mode : TV works alone, without an SI STB or SBB.
•Interactive mode : Samsung / OCC / MTI / Nstreams / Enseo / Cardinal / Guestek / Seachange /
MDC / Innvne
•Standalone mode : OFF / Smoovie
Power On Channel
Set the default values that will be applied when the TV is turned on.
•User Defined : Lets you set Power On Channel and Channel Type manually. See Power On
Channel and Channel Type below.
•Last Saved : If you select this item, when the TV is turned on, it displays the channel it was
displaying when it was turned off.
Power On Channel
Num
When the TV is turned on, it switches automatically to this channel.
Power On Channel
Type
Select channel band : AIR (analogue air band), DTV (digital air band), CATV (analogue cable band),
CDTV (digital cable band)
Power On Volume
•User Defined : Lets you set the Power On Volume manually. See Power On Volume below.
•Last Saved : When the TV is turned on, it returns to the volume that had been set when the
power had been turned off.
Power On Volume Num The TV turns on with this Volume Level in Stand Alone Hospitality mode.
Min Volume
The minimum Volume Level the user can set in Stand Alone Hospitality mode.
Max Volume
The maximum Volume Level the user can set in Stand Alone Hospitality mode.
Power On Source
Select the input source the TV displays when turns on.
Power On Option
Determines the TV's state when power returns after a power failure or after you have unplugged
the TV and then plugged it in again.
•Last Option : Returns to its last Power state. If it was in Stand-by, it returns to Stand-by. If it was
on, it turns on.
•Power ON : When the power returns, the TV turns on.
•Standby : When the power returns, the TV enters the Standby mode.
Channel Setup
Gives you direct, immediate access to some of the Channel menu functions on the user Channel
menu such as Auto Tuning, Antenna selection, etc.
Channel Editor
The Channel Editor lets you edit the channels stored in the TV's memory. Using Channel Editor you
can:
•Change the channel numbers and names, and sort the channels in your desired channel number
order.
•Apply the video mute to channels you select. The video mute blanks out the video from a channel
and outputs only the sound while displaying a speaker icon on the screen.
The Channel Editor also lets you view information about each channel easily, without your having to
display each channel directly.
Mixed Channel Map
This Feature enables showing/browsing all antenna type (Air/Cable or Satellite) channels at the
same time.
•ON: When ON, guests can access the complete Channel Map irrespective of the selected
antenna type. The Channel list will also populate Air as well Cable type channels.
•OFF: When OFF, guest can access the Channel Map corresponding to the selected antenna type
[AIR/CABLE or Satellite] only. The Channel list/Editor will only show the selected antenna type
channels.
Channel
Dynamic SI
•ON : Check the DTV Programme channel number. (the TV channel editor is inaccessible)
•OFF: Do not check the DTV Programme channel number.
(the DTV channel editor is accessible, but additional channel Programme number update is not
supported)
English
17
Hotel TV Function
Category
Description
Item
Channel Rescan
Message
Channel
Mychannel
Genre Editor
When there is a mismatch between the data in the channel map and the transmitted data, the TV
autotunes the channels to restore the data/parameters in the channel map.
•ON: When Channel Rescan Message is ON, the OSD showing that the channels are being
rescanned will be displayed to Hotel Guests.
•OFF: A Hotel Admin can turn the Channel Rescan Message OFF, if the rescan message OSD
should not to be displayed to Hotel Guests.
Enable or disable the Mychannel feature.
Edith the genre for channels. (Available when Mychannel is On)
TTX Widescreen Mode Widen the subtitle section to fit the screen width.
Picture Menu Lock
Menu Display
•ON : Main Menu display.
•OFF : Main Menu No display.
Tools Display
Hide or show the Tools menu.
Channel Menu Display
Menu OSD
Panel Button Lock
Home Menu Editor
Edit Home Menu.
OFF : No clock option of Factory menu shall work. Only Main menu.
SW Clock : SW clock shall work only.
Local Time
Select the method to update the clock data.
•Manual: Use clock data from DVB channel or manual clock setting When the TV is in the standalone mode.
•TTX: Bring up the time information from the TTX stream.
•Time Channel: Use clock data from the selected Channel type and Channel num.
Timer Type
Enable or disable the alarm function.
•WakeUp : Enable the alarm function to turn on the device at the specified time.
•OnOff : Disable the Alarm function.
Priority HDMI
If the jack priority is set, the corresponding source is automatically set when a jack is inserted
according to the jack priority.
HDMI Option
Select which HDMI source of the TV is connected to the RJP jack.
When USB is connected to the TV,
•Default : A popup window appears.
•Automatic : This Enters the USB content menu automatically.
•Disable : Nether the pop-up window nor the menu appears.
External Source
Banner
Users can set External Source Banner to On or Off.
•ON : When TV power is On or the Mode changes, the TV will displays the external source banner.
•OFF : When TV power is On or the Mode changes, the TV does not display the external source
banner.
Auto Source
•OFF : Auto Source is Off.
•ON : When an external source is connected to the TV, the TV will auto-ident and switch the input
source.
•PC : Auto Ident PC Input only.
Anynet+ Return Source
English
Backlight On/Off option in Music mode to save energy.
If the jack priority is set, the corresponding source is automatically set when a jack is inserted
according to the jack priority.
External
Source
18
To get music output from an mp3/audio player through a PC Input Source. When on, you can hear
sound from the player through the TV even there is no video signal. The TV’s backlight, however,
remains on. And add a video signal,it works normally.
Priority PC
USB Pop-up Screen
External
Source
ON : The Home Menu is Auto Start.
OFF : The Home Menu is not Auto Start.
Clock Type
Music Mode Backlight
Remote
Jack Pack
Turning the front panel (local key) operations on/off.
•Unlock : Unlocks all panel keys.
•Lock : Locks all panel keys.
•OnlyPower : Locks all panel keys except the Power panel key.
•Menu/Source : Locks the Menu and Source panel keys.
OFF : The Home Menu is not displayed.
ON : The Home Menu is displayed.
Music Mode PC
Music Mode
Hide or show the Channel menu.
Home Menu Display
Home Menu Auto Start
Clock
Enable or disable the Picture Menu.
Select the return TV source after stopping an Anynet+(HDMI-CEC) connection. (This fuction is
especially useful for the Guestlink RJP.)
Hotel TV Function
Category
HP Mode
HP
Management
Eco Solution
Description
Item
Default HP Volume
•ON: When the Headphone is connect to the TV, allows you to listen to audio through the TV's
speakers and the connected headphones simultaneously. But, you can only adjust the volumes
of TV speaker.
•OFF: When the Headphone is connect to the TV, allows you to listen to audio through the
connected headphones only.
Configure the values of headphones' volume when HP Mode is set to ON.
Main Speaker
•ON: Plays the TV sound through the TV speaker.
•OFF: Plays the TV sound through the headphones only.
Energy Saving
Adjusts the brightness of the TV to reduce power consumption.
•Off: Turns off the energy saving function.
•Low: Sets the TV to low energy saving mode.
•Medium: Sets the TV to medium energy saving mode.
•High: Sets the TV to high energy saving mode.
Welcome Message
Displays on Welcome Message.
Edit Welcome Message Edit the Welcome Message.
Hospitality Logo
Logo/
Message
Turns the Hospitality logo feature On or Off, if On, when the TV isturned on, the Logo is displayed,
before the signal from the initial source, for the amount of time set in "Logo Display Time"
Hospitality Logo DL
Downloads the Hospitality logo.
Hospitality logo file requirements:
•BMP or AVI files only.
•Max file size : BMP - 960 X 540. AVI - 30MB.
•The file can only be named samsung.bmp or samsung.avi.
Logo Display Time
Set the logo display time (3/5/7 Seconds).
Clone TV to USB
Clone the current TV option values to a USB memory device.
Clone USB to TV
Clone the saved TV option values in a USB memory device to the TV.
Cloning
Setting Auto Initialize
REACH 3.0
REACH Channel
Group ID
Ticker
REACH
Solution
REACH Update Time
When Setting Auto Initialize is set to On, and the power is turned off and on or the Master Power is
turned off and on, the data is restored to the cloned values. If there is no cloned value, even when
the Setting Auto Initialize is set to On, it will be ignored and the operation will be the same as that
when Setting Auto Initialize is set to Off.
ON : The feature of REACH 3.0 in this TV becomes available.
OFF : The feature of REACH 3.0 in this TV becomes not available.
Assign a DTV channel number to carry the update REACH data. This channel number must be the
same as the number set on the Reach server.
Select the Group ID of the REACH server.(Refer to the REACH server manual for more details.)
ON : The Ticker content is displayed.
OFF : The Ticker content is not displayed.
Lets you set when data such as updated SW, cloning files, and S-LYNC REACH contents is
downloaded from the REACH server to the TV :
1hour : Every hour
2hour : Every 2 hours
12:00 am : Every 12:00 a.m.
12:00 pm : Every 12:00 p.m.
2:00 pm : Every 2:00 p.m.
REACH Update
Immediate
ON : Whenever the TV enters standby mode (the power cord is plugged in and the power is off),
the REACH data is updated on the TV.
OFF : The REACH data is only updated on the TV at the REACH server update time.
Room Number
Set the Room Number.
REACH Server Version The version of REACH Server is displayed.
Network Setup
Network
Set an IP address to establish an Internet connection.
SmartHub Model
Setting
Set SmartHub Model.
SmartHub Setting
Set up SmartHub.
English
19
Hotel TV Function
Category
Widget Mode
Widget Mode ON/OFF.
Solution Type
Select type of solution (Vender Server/ SINC Server).
Server URL Setting
License Server IP
Setting
Widget
Solution
IPTV Mode
Virtual Standby
Instant On
Room Num Setting
Set server URL.
Set server IP.
IPTV mode On/Off.
Virtual Standby mode On/Off.
When Virtual Standby is On, TV power consumption will be 9.5W to 17.4W (Depending on the size
of the TV screen).
Setup booting mode.
Set Room Number.
Self Diagnosis
for TV
Enter Self Diagnosis Menu.
•Picture Test: Use to check for picture problems. If the problem appears in the test picture, select
Yes and follow the directions on the screen.
•Sound Test: Use the built-in melody sound to check for sound problems. If the problem occurs
during the test, select Yes and follow the directions on the screen.
Self Diagnosis for HTV
HD Function Check Menu On Executing Item Below OSD is displayed ProIdiom DTV Channel Key
Loss : Ok/Failure (Hotel US) STB SI Vendor
Setting : SI Name Ok/Failure
Bathroom AMP : Ok/Failure (Hotel EU)
RTC : Ok/Failure (Hotel EU)
System
SW Update
Same function with SVC Service Pattern.
Sound Bar Out
ON: TV speaker sound will be mute. Sound will come out through HDMI.
You must connect the Sound Bar to hear the sound.
OFF: Sound will come out through TV speakers normally.
Standby LED
TV Reset
English
SW USB Update function.
Service Pattern
Contact Samsung
20
Description
Item
Display the web site of related Samsung service center, software version, and Mac address
information when the TV has a problem.
When the TV is in standby mode, you can configure the settings of external LED.
•ON: The LED is on.
•OFF: The LED is off.
Returns all settings on the TV to their factory defaults.
Welcome Message
The welcome message is used to display custom messages on the TV every time TV is turned on by a Guest in Hotel room.
−− Welcome message settings are found in the Hotel Option Menu.
−− Welcome message should be ON in order to display the message on power-on.
Hospitality Mode
Standalone
SI Vendor
OFF
Power On
Network
Widget Solution
System
Channel
Menu OSD
Clock
Welcome Message
Music Mode
Edit Welcome Message
r
Remote Jack Pack
External Source
ON
Hospitality Logo
OFF
Hospitality Logo DL
...
Logo Display Time
...
Bathroom Speaker
HP Management
Eco Solution
Logo/Message
Cloning
REACH Solution
−− A welcome message can be up to 25 characters and it can be edited by changing the text in the Hotel Service
menu.
−− The following is the list of characters supported by Welcome message:
✎✎ Capital letters, from A-Z
−− Welcome message can be edited by using the navigation, colour & enter key on the Remote in the “Edit Welcome
Message” OSD.
Edit Welcome Message
W
E
L
C
O
M
E
_
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Move
Enter
A
Move to left
B
Move to Right
C
Leave Black
D
Done
Return
−− The Welcome message and hotel logo cannot both be active at the same time.
English
21
Hotel Logo
The Hospitality Logo function displays the Hotel's picture image when the TV is initially powered on.
−− Hospitality Logo settings are the Hospitality mode menus.
−− The Logo Download and Logo Display Menu items are enabled when you turn the Hospitality Logo option on.
−− If there is a logo image stored in memory and the Hospitality Logo option is on, the Hospitality logo is displayed
when the TV is turned on.
−− The Hospitality logo is not displayed when the Hospitality found Logo option is off, even if the logo image has been
loaded into the TV.
Hospitality Mode
SI Vendor
Standalone
OFF
Power On
Network
Widget Solution
System
Channel
Menu OSD
Clock
Welcome Message
Music Mode
Edit Welcome Message
Remote Jack Pack
External Source
Bathroom Speaker
r
Hospitality Logo
OFF
BMP
Hospitality Logo DL
Logo Display Time
5 Second
HP Management
Eco Solution
Logo/Message
Cloning
REACH Solution
• Hospitality Logo
−− This option lets you choose whether the Hospitality Logo image is displayed or not.
−− Initial value is OFF.
−− Can be set to OFF or ON.
−− When set to ON, the Logo Download and Logo Time Display menu items become accessible.
• Hospitality Logo DL
−− This option lets you download the logo image to the TV’s memory from a USB device.
−− A wait message appears while the image is being copied to the TV.
−− A "completed" message appears when the copy operation finishes successfully.
−− The word "failed" appears if the copy operation was unsuccessful.
−− No USB appears if no USB device is connected.
−− No File appears if there is no file to copy on the USB device or or the file is in the wrong format must be a BMP file.
If No File appears and there is a logo file on the USB device, check the file format.
• Logo File Format
−− The TV supports only BMP and AVI format.
−− The file name must be samsung.bmp or samsung.avi.
−− The maximum resolution of the BMP format is 960 x 540.
−− The maximum file size for AVI format is 30MB.
−− The TV does not change the size or scale of the image.
22
English
USB Cloning
USB Cloning is used to download user-configured settings (Picture, Sound, Input, Channel, Setup, and Hotel Setup)
from one TV set and upload them to other TV sets.
All the user-defined settings from the TV (Master Set) can be copied to the USB device.
• Cloning from TV to USB: This copies stored data from the TV set to the USB
device.
1. Insert a USB drive into the USB port on the rear of the TV.
2. Enter the Interactive menu by pressing buttons in order.
• MUTE → 1 → 1 → 9 → ENTER
3. Press the ▲ or ▼ button to select “Clone TV to USB”, then press the ENTER
button.
4. When the message “Clone TV to USB” is displayed, press the ENTER button.
5. You can verify USB cloning behavior.
• In Progress: during copying data to USB.
• Completed: copy was finished successfully.
• Failed: copy was not finished successfully.
• No USB: USB is not connected.
• Cloning from USB to TV: This to downloads the stored data in the USB device to
TV set.
Logo/Message
Cloning
d
Clone TV to USB
Clone USB to TV
Setting Auto Initialize
Logo/Message
Cloning
d
1. Insert a USB drive into the USB port on the rear of the TV.
2. Enter the Interactive menu by pressing buttons in order: MUTE → 1 → 1 → 9 →
ENTER
OFF
Clone TV to USB
Clone USB to TV
Setting Auto Initialize
OFF
3. Press the ▲ or ▼ button to select “Clone USB to TV”, then press the ENTER
button.
4. When the message “Clone USB to TV” is displayed, then press the ENTER button.
5. You can Make sure USB cloning behavior.
• In Progress: copying data to TV.
• Completed: copy finished successfully.
• Failed: copy did not finish successfully.
• No USB: USB is not connected.
• No File: there is no file to copy on the USB.
✎✎ Activate copying from USB to TV by pressing ENTER key for 5 seconds.
✎✎ The Hotel TV product family does not support the CLONE function between models that supports the satellite / T2
operation and models that do not.
For fast, instant cloning during installation,
insert a USB drive with master settings from the first TV and press the Enter key for 5 seconds.
English
23
Setting Auto Initialize
When you clone settings from one TV to another, you clone both the guest side menu and hotel side menu settings: Picture,
Sound, Input, Channel, Setup, and Hotel Setup). This lets you set nearly all of the menu values on your hospitality TVs to
the same, standard settings. If you allow guests access to the guest side menus, for example the Picture menu, they can
change the settings in those menus so they are no longer standard. If you set the Setting Auto Initialize function to on, the
TV automatically restores (initializes) any guest-side menu values to the cloned, standard values when the TV is turned off
and then turned on again. Note that Setting Auto Initialize works on cloned guest side menu values only. Settings which
have not been cloned are ignored.
The table below lists the settings that are restored to their cloned values when you set the Setting Auto Initialize function to
on.
Menu
Picture
Sound
24
Menu Item
Picture Mode
Backlight
Contrast
Brightness
Sharpness
Colour
Tint (G/R)
Apply Picture Mode
Picture Size
Picture Size
Zoom/Position
4:3 Screen Size
Auto Adjustment
PC Screen Adjustment
Coarse
Fine
Position
Image Reset
PIP
Advanced Settings
Dynamic Contrast
Black Tone
Flesh Tone
RGB Only Mode
Colour Space
White Balance
Gamma
Motion Lighting
Picture Options
Colour Tone
Digital Clean View
MPEG Noise Filter
HDMI Black Level
Film Mode
LED Clear Motion
Picture Off
Reset Picture
Sound Mode
Sound Effect
DTS TruSurround HD
DTS TruDialog
Equaliser
Speaker Settings
Additional Settings
DTV Audio Level
Audio Format
Audio Delay
Dolby Digital Comp
Auto Volume
Reset Sound
English
Menu
System
Menu Item
Accessibility
Audio Description
Subtitle
Menu Transparency
High Contrast
Enlarge
Football Mode
Menu Language
Smart Control Settings
Motion Sensitivity
Touch Sensitivity
Onscreen Remote Size
Voice Control
Language
Use TV Voice
Voice Gender
Device Manager
Keyboard Settings
Mouse Settings
Time
Clock
Sleep Timer
Alarm
Eco Solution
Energy Saving
Eco Sensor
No Signal Power Off
Auto Power Off
Smart Security
Auto Protection Time
Change PIN
General
Game Mode
Sound Feedback
Boot Logo
Samsung Instant On
Anynet+(HDMI-CEC)
DivX® Video On Demand
Plug & Play
Hotel Plug & Play automatically performs Hotel mode selection, Country Setup, Clock Setup and Picture mode Setup.
−− Hotel Plug & Play is available only one time when power is first turned ON.
−− This is available after first setting up the TV and transferring Clone TV data to a USB drive.
−− To use next TV, you only need to exit Hotel Plug & Play, connect the USB, then Clone the USB to TV.
−− Depending on model and region, some menus may not exist.
Local Set
Local Set
If you select
Change
Change Local Set if Located in North America, Latin America and Europe.
In other regions, Please press SKIP button move to the next step.
Warning! TV might not function if Local Set is not correctly configured.
When Local Set is changed, TV will turn off automatically to apply it.
Current Localset : EU
E
Skip
Change
Next
EU
If you change the
country of the Current
Location
The TV is
automatically turned
off and on
Countries List
Bulgaria, Croatia, Czech, Estonia, Greece, Hungary, Latvia, Lithuania,
Romania, Serbia, Slovakia, Slovenia, EU-Others
If you select Skip
E
E
TV Setup Complete!
Easy Set Up
Your TV is now ready to use.
If you select this, Easy
setup will be started.
There are Essential
Details, Channel Scan,
Clock and Terms in Easy
setup.
Intercactive
(Hotel Menu)
c
Standalone Setup
Previous
Next
(Continue Setup)
Standalone Only
(End Setup)
E
OK
If you select
Standalone Setup
E
Clock
Select your Language
You can adjust your time to set DST, Time Zone and clock
mode
Select your language to start the on screen setup.
Clock Mode
c
English
Previous
Fraçais
Press the udlr buttons
to move the highlight.
Press the enter button to
select.
Deutsch
Italiano
Next
Set current date and time
Auto
Date
-- / -- / ----
Time
-- : --
Time Zone
Auto
DST
Next
Off
-- : --
Polski
The Language Setting will be applied to Main Menu and not Plug and Play.
E
Select your language
E
Auto Tuning
Essential Details
This is basic setup to use your Smart TV.
Previous
Country
Bulgaria
Picture Mode
Standard
Auto Tuning completed.
Please Select your country.
Previous
Next
Digital
- TV
- Radio
- Data/Other
0
0
0
0
Analogue
0
Next
Change settings
Scan Again
E
Auto Tuning
Auto Tuning
Auto Tuning
How do you get your broadcast signal?
To receive channels, configure the options belows then
select Scan.
Auto tuning is finding channels for you...
c
Previous
E
E
Both
Terrestrial/Cable
Satellite
Select Both to scan for both
Terrestrial or Cable channels and
Satellite channels.
Next
Aerial
Previous
Channel Type
E
Terrestrial
Digital & Analogue
Scan
Channel
Select the connected aerial that
you want to use to get channels.
Next
Previous
7
2%
Digital
- TV
- Radio
- Data/Other
0
0
0
0
Analogue
0
Next
Stop
English
25
• Plug & Play OSD
−− Initial Highlight: Interactive
−− If Standalone Only button is selected, Standalone hotel mode is set by default and “Standalone mode is set”
OSD is displayed for 3 seconds.
−− TV enters into RF mode automatically after displaying “Standalone mode is set” OSD for 3 seconds.
−− When Interactive mode is selected, the Interactive Setup Menu appears. Press the power off button to exit from the
Interactive menu.
−− When Standalone Plug & Play mode is selected, the “Select Menu Language” OSD is displayed.
• Select Menu Language OSD
−− When Standalone Plug & Play is selected from “Easy Set Up” OSD, “Select Menu Language” OSD is displayed.
−− Initial Highlight : English
−− Display time: OSD timeout and operation are the same as Samsung's consumer TV models.
−− If the ENTER button is pressed, “Select Area” OSD is displayed.
• Select Country
−− Initial Highlight: United Kingdom.
−− The Country OSD is displayed and the area can be selected.
• Clock setting OSD
−− Display time: 30 seconds.
−− The Clock Set item OSD is displayed
−− If ENTER button is pressed after setting the clock or in Auto, Picture Mode OSD is displayed.
• Auto Search Mode OSD
−− If skip option is selected, this goes to Clock setting OSD.
−− If the ENTER button is pressed, auto searching of channels is performed.
−− The OSD Display time, from the time that Auto Store is started to the time that Auto Sort is completed, is 30
seconds.
• Picture Mode OSD
−− Initial Highlight: Standard.
−− The Picture Mode OSD is displayed and the Dynamic or a Standard Picture mode can be selected.
−− After selecting the picture mode and the TV enters Standalone Setup Menu OSD, press power off to exit.
26
English
Multi Code Remocon
Multi Code Remocon is a special transmitter which is designed to control each TV with one remote.
This is useful where there is more than one TV in a location, such as in a hospital the set ID number is displayed in the
source osd. It is possible to support up to 9 different remote key transmissions for multiple codes.
Each TV has an initial code of "0".
−− The ID code can be set and reset in Analogue TV mode or PC mode. (not available in TTX channel or DTV channel.
−− ID code can be from 0 to 9.
−− Press the MUTE button and the RETURN button simultaneously for more than 7 seconds and then select the
number button to set the code.
−− Set ID OSD appears.
−− The following words appear: “Remote control code is set to X. If you want to change the Remote control code,
enter the chosen digit.” X is the digit number.
✎✎ This OSD displays until Exit is pressed.
Remote control code is set to 0. If you want
to change the Remote control code, enter the
chosen digit.
−− For example, TV and Remote will be set to ID code #1 if the user presses #1.
−− The following words appear: “Remote control code is changed to 1” At this point, the TV can be controlled only by
the remote with the same ID code as the TV.
−− TV, the following words will be displayed. “ TV ID x”(x is the TV’s ID)
−− To reset the ID code, press the MUTE button and the EXIT button simultaneously for more than 7 seconds. When
you stop pressing the buttons, the ID code for both the TV and Remote are reset to “0”. “Remote control code is
set to 0.” appears.
English
27
CH Bank Editor (Smoovie TV Only)
Channel Bank Editor edits channels, with 3 different Bank Options.
Depending on the Bank card, there are specific channels Hotel customers can enjoy.
Setting the CH Bank Editor under Stand-alone Mode
1. Enter the Hotel Standalone menu by “MUTE+1+1+9+Enter”
2. Please select SI vendor : “Smoovie”
3. find the new menu option, “Channel Bank Editor”
4. Enter the “Channel Bank Editor”
Hospitality Mode
Standalone
SI Vendor
OFF
REACH Sever
Network
d
SI Vendor
Smoovie
d
Channel
d
Channel Bank Editor
<Depending on model and region, some menu items may not exist>
5. Edit the channel bank like below example.
a. BANK1 (Free channel): Select the channel that will be used when remote doesn’t have any card.
b. BANK2 (Family Card - Green): Select the channel that will be used when remote has a GREEN CARD.
c. BANK3 (Adult Card - Red): Select the channel that will be used when remote has a RED CARD.
Channel Bank Edit
Registered
1
1futech
2
BBC1
3
24ore.tv
4
C3
5
BBC World
6
C5
7
Coming Soom
8
S2
9
S2
Bank1 (4)
Bank2 (6)
n Move
Bank3 (36)
Select/Deselect
Return
References of using SMOOVIE Remote Controller
1. If you select SMOOVIE as the SI vendor, you should use the SMOOVIE Remote Controller.
2. With the Numeric keys of the remote controller, users can select only the Bank1 channel.
To change the channel using the Green or Red Card, please use channel up/down keys.
3. For the Channel guide or the Channel list, users can see only Bank1 channel list.
28
English
Channel Editor
Channel Editor edits channel number a and name.
−− Use Channel Editor to sort the channels as user-desired channel numbers.
Hospitality Mode
Standalone
SI Vendor
OFF
Power On
Network
Widget Solution
System
Channel
Menu OSD
Clock
Music Mode
r
Remote Jack Pack
External Source
Channel Editor
Bathroom Speaker
HP Management
Eco Solution
Logo/Message
Cloning
REACH Solution
<Depending on model and region, some menu items may not exist>
Simple Steps for channel Editor under Stand-alone Mode
Step
Broad Outline
1
Operate ‘Channel Auto Store’ in Hotel Option Menu
2
Enter ‘Channel Editor’ in Hotel Option Menu
3
Compile a table related to the final channel lists you want to have
4
Rearrange channels with the TOOLS Button based on the table you compiled
5
Press the EXIT or RETURN Button to exit.
<please refer to the following details>
Smoovie On sequence
Smovie TV used (Air/ Cable )
Step
Mixed Channel Map On (Air and Cable both used)
If the tv starts with Hotel P&P
1
Do the P&P, except channel
store
Only Air or Cable used
Only Air or Cable used
If P&P already done
If the tv starts with Hotel P&P
If P&P already done
Enter Hotel menu
Do the P&P all (Air or Cable
auto tune)
Enter Hotel menu
After P&P TV will show hotel
menu
Select channel type
- ATV or ADTV for Air
- CATV or CDTV for cable
2
After P&P TV shows hotel
menu
Setup Mixed Channel Map
On
3
Setup Mixed Channel Map
On
TV power off & on
4
Make TV power off & on
Enter Hotel menu
5
Enter Hotel menu
Select smoovie TV in Hotel
menu
6
Select smoovie TV in Hotel
menu
Select Channel Setup
7
Select Channel Setup
Select "Air + Cable" to auto
tune
Setup CH Bank Editor
8
Select "Air + Cable" to auto
tune
Setup CH Bank Editor
After power off & on, user can
use TV
9
Setup CH Bank Editor
After power off & on, user can
use TV
10
After power off & on, user can
use TV
Select channel type
- ATV or ADTV for Air
- CATV or CDTV for cable
Select smoovie TV in Hotel
menu
Select Channel Setup
(can be skipped)
Select "Air" or "Cable" to auto
tune (can be skipped)
Select smoovie TV in Hotel
menu
Select Channel Setup
Select "Air" or "Cable" to
auto tune
setup CH Bank Editor
After power off & on, user can
use TV
English
29
Smovie TV used( Satellite )
Mixed Channel Map On (Satellite and Air or Cable both
usedused)
Step
If the tv starts with Hotel P&P
Do the P&P except channel
store
1
Only Satellite used
If P&P already done
If the tv starts with Hotel P&P
Enter Hotel menu
Do P&P all: Air or Cable auto
tune)
Enter Hotel menu
after P&P TV shows hotel
menu
Select channel type
- ATV or ADTV for Air
- CATV or CDTV for cable
2
After P&P TV will show hotel
menu
Setup Mixed Channel Map On
3
Setup Mixed Channel Map On
Make TV power off & on
4
Make TV power off & on
Enter Hotel menu
5
Enter Hotel menu
Select smoovie TV in Hotel
menu
6
Select smoovie TV in Hotel
menu
Select Channel Setup
7
Select Channel Setup
Select Satellite to auto tune
Setup CH Bank Editor
8
Select Satellite to auto tune
Setup CH Bank Editor
After power off & on, user can
use TV
9
Setup CH Bank Editor
After power off & on, user can
use TV
10
After power off & on, user can
use TV
Select channel type
- ATV or ADTV for Air
- CATV or CDTV for cable
Select smoovie TV in Hotel
menu
Select Channel Setup (can be
skipped)
Select Satellite to auto tune
(can be skipped)
If P&P already done
Select smoovie TV in Hotel
menu
Select Channel Setup
Select Satellite to auto tune
Setup CH Bank Editor
After power off & on, user can
use TV
Channel List
You can view channel information, All, TV, Radio, Data/Other, Analogue or Favourites 1-5.
✎✎ When you press the CH LIST button on the remote control, Channel List screen displays immediately.
Contents Home
Channel List
Guide
AllShare Play
Schedule Manager
Source
R Return
* The displayed image may differ depending on the model.
•
•
•
•
•
•
All: Shows all currently available channels.
TV: Shows all currently available TV channels.
Radio: Shows all currently available radio channels.
Data/Other: Shows all currently available MHP or other channels.
Analogue: Shows all currently available analogue channels.
Favourites 1-5: Shows all favourite channels.
✎✎ If you want to view added favourite channels press the CH LIST button and use the L (Ch. Mode) button to move
between Favourites 1-5.
✎✎ Using the control buttons with the Channel List.
• T (Tools): Displays the option menu.
• L (Ch. Mode / Channel): Move to the All, TV, Radio, Data/Other, Analogue or Favourites 1-5.
• When you select the Programme View in T (Tools) menu, you can move to other channels using L (Channel)
button.
• E (Watch / Information): Watches the channel you selected. / Displays details of the selected programme.
• k (Page): Move to the next or previous page.
30
English
How to use Schedule Viewing in Channel List
(digital channels only)
When you set the Schedule Viewing in Channel List, you can only set the programme in Programme View.
1. Press the CH LIST button, then select a desired digital channel.
2. Press the TOOLS button, and then select Programme View. The programme list for that channel appears.
3. Press the ▲ / ▼ buttons to select the desired programme, then press the ENTERE (Information) or INFO button.
4. Select Schedule Viewing, then press the ENTERE button when done.
✎✎ If you want to cancel Schedule Viewing, follow steps 1 through 3. Select Cancel schedule.
Using Option Menu t
Set each channel using the Channel List menu options (Programme View, Edit Favourites, Lock/Unlock, Edit Channel
Name, Edit Channel Number, Delete, Information, Sort, Edit Mode).
Option menu items may differ depending on the channel status.
1. Select a channel and press the TOOLS button.
2. Select a function and change its settings.
• Programme View: Displays the programme when a digital channel is selected.
• Edit Favourites: Set channels you watch frequently as favourites. Add or delete the selected channel in Favourites 1-5.
1. Select the Edit Favourites, then press the ENTERE button.
2. Press the ENTERE button to select Favourites 1-5, then press the OK button.
✎✎ One favourite channel can be added to several favourites among Favourites 1-5.
• Lock/Unlock: Lock a channel so that the channel cannot be selected and viewed.
✎✎ This function is available only when the Channel Lock is set to On.
✎✎ The PIN input screen appears. Enter your 4-digit PIN. Change the PIN using the Change PIN option.
• Edit Channel Name (analogue channels only): Assign your own channel name.
• Edit Channel Number (digital channels only): Edit the number by pressing the number buttons.
✎✎ Some areas may not be able to support Edit Channel Name and Edit Channel Number.
• Delete: You can delete a channel to display the channels you want.
• Information: Displays details of the selected programme.
• Sort: Changes the list ordered by channel number or channel name.
• Edit Mode: Select desired channels and edit them.
English
31
Using Option Menu t
Set each channel using the menu options (Edit Favourites, Lock/Unlock, Delete, Deselect, Select All).
1. Press the TOOLS button in Channel List screen, then select the Edit Mode. A check box appears to the left of the
channel.
2. Press the ▲/▼ buttons to select the desired channel, then press the ENTERE button. The (c) mark indicates the
channel you’ve selected.
✎✎ You can select more than one channel.
✎✎ Press the ENTERE again to deselect the channel.
3. Press the TOOLS button, then select a function and change its settings.
• Edit Favourites: Set the selected channels you watch frequently as favourites.
✎✎ The Edit Favourites screen has five groups (Favourites 1, Favourites 2, etc.). You can add a favourite channel to
any one of the groups. Press the ▲/▼ buttons to select a group.
• Lock/Unlock: Lock a channel so that the channel cannot be selected and viewed.
✎✎ This function is available only when the Channel Lock is set to On.
✎✎ The PIN input screen appears. Enter your 4-digit PIN. Change the PIN using the Change PIN option.
• Delete: You can delete a channel to display the channels you want.
• Deselect: Deselect the selected channels.
• Select All: Select all the channels in the channel list.
32
English
My Channel
Determines the country and genre for the channels provided by the hotel, and if the user selects a country and genre, shows
the corresponding channels.
• You must select the country first, or you can not set a genre.
• If you select the genre without adding any channels, the channel list displays all of the available channels.
• My Channel works in Standalone mode only.
• SI Vendor in Standalone mode: This does not work if Smoovie is selected.
• This is in the Hotel Options in Hotel Menu > Service Mode and can be turned on or off.
• The option only works when it is set to On.
• Channel Composition [Genre Mode]
Standard
Hotel
Category
Ch. Mode
Genre
All (Default)
News
Radio
Entertainment
Sport
Hotel
2
1
3
Current status : Austria/Sports
6
Antenna Mode Activation
Air/Cable
Satellite
O
O
O
O
O
O
O
O
O
O
O
O
Description
Provide genre channel mode by each country that
master has managed in factory mode.
My Channel
4
5
Country
Genre
All Country
All
Austria
News
Belgium (Dutch)
Radio
Belgium (French)
Entertainment
Czech
Sports
France
Germany
▼
Hotel
7
(Blue)Keep Previous (U/D/L/R)Move (En)Enter 8
* For the number of items to be displayed in the list, refer to the design document.
Key Guide
Button
Action
Nav. Help
BLUE
Returns to the screen. (Genre setup: Last Country & Genre)
Keep Previous
ENTER
Selects an item.
Enter
Ch. Up/Down
Move the highlight by page.
(No Guide)
UP/DOWN
Navigates the each country, genre list. (in a circular manner.)
RIGHT
Selects the highlighted item, and then move the highlight to Genre section.
RETURN
Returns to the screen. (Genre setup: Last Country & Genre)
(No Guide)
EXIT
Returns to the screen. (Genre setup: Last Country & Genre)
(No Guide)
Move
English
33
✎✎ NOTE
• This section describes the layout of the Front UI that appears when the TV is turned on. (Factory Mode > Genre
Mode: Enable)
• The genre is a sub-list for each country.
• The broadcast screen that was being displayed the last memorial channel.
−− If user want to keep the previous country & genre channel map, press the ‘BLUE’, RETURN, and EXIT remotecontrol key to close the Front UI.
✎✎ ETC.
• Default Highlight : Last Memory items (Country, Genre)
• Timeout (60 sec)
Elements
No
Name
Description
1
Background Screen
Displays the last memorized channel that appears when TV is turned on.
2
Function Title
This is name of the function.
3
Current Status
4
Country Items
5
Genre Items
Display current settings the Country/Genre.
The item for the country list is displayed.
Displays the last selected country.
The item for the genre list is displayed.
Displays available genre items by each country that master managed in factory
mode. (always provide ‘All’ item)
Displays the last selected genre.
6
Highlight
If the item title is too long to be displayed within the area, Auto Text Sliding works.
7
Indicator
This is displayed when there is a previous or next page.
8
Nav. Help
The key guide is right-aligned.
34
English
Highlight Interaction [Country Items]
• This page is only to indicate possible interactions. It may not be exactly identical to actual screens.
✎✎ NOTE
• Users can navigate the items in each country & genre list by pressing the up or down remote control keys.
• Circular navigation is supported.
1
My Channel
My Channel
Current status : All Country/Sports
Current status : All Country/Sports
Country
Genre
▲
DOWN x 4
Country
Genre
▲
All Country
All
All Country
All
Austria
News
Austria
News
Belgium (Dutch)
Radio
Belgium (Dutch)
Radio
Belgium (French)
Entertainment
Belgium (French)
Entertainment
Czech
Sports
Czech
Sports
France
Hotel
France
Hotel
UP x 4
Germany
Germany
▼
▼
UP x 4
DOWN x 4
My Channel
Current status : All Country/Sports
Country
Genre
▲
All Country
All
Austria
News
Belgium (Dutch)
Radio
Belgium (French)
Entertainment
Czech
Sports
France
Hotel
Germany
▼
DOWN
UP
UP
DOWN
My Channel
Current status : All Country/Sports
Country
Genre
▲
Austria
All
Belgium (Dutch)
News
Belgium (French)
Radio
Czech
Entertainment
France
Sports
Germany
Hotel
Hungary
▼
UP x N
DOWN x N
END
My Channel
My Channel
Current status : All Country/Sports
Country
Current status : All Country/Sports
Genre
▲
Country
Genre
▲
Slovakia
All
Slovakia
All
Spain
News
Spain
News
Switzerland
Radio
Switzerland
Radio
United Kingdom
Entertainment
United Kingdom
Entertainment
Eastern Europe
Sports
Eastern Europe
Sports
Other
Hotel
Other
Hotel
▼
▼
English
35
Highlight Interaction [Default Genre]
• This page is only to indicate possible interactions. It may not be exactly identical to actual screens.
My Channel
My Channel
Current status : All Country/Sports
Country
Current status : All Country/Sports
Genre
▲
All Country
All
Austria
News
Country
ENTER / RIGHT
Genre
▲
All Country
All
Austria
News
Belgium (Dutch)
Radio
Belgium (Dutch)
Radio
Belgium (French)
Entertainment
Belgium (French)
Entertainment
Czech
Sports
Czech
Sports
France
Hotel
France
Hotel
LEFT
Germany
Germany
▼
▼
Navigation Help Area
Navigation Help Area
• The current selection of the country is high-lighted.
• Default High-light: The current selection of the genre.
My Channel
My Channel
Current status : All Country/Sports
Country
Current status : All Country/Sports
Genre
Country
▲
All Country
All
Austria
News
ENTER / RIGHT
All Country
All
Austria
News
Belgium (Dutch)
Radio
Belgium (Dutch)
Radio
Belgium (French)
Entertainment
Belgium (French)
Entertainment
Czech
Sports
Czech
Sports
France
Hotel
France
Hotel
LEFT
Germany
Germany
▼
▼
Navigation Help Area
• Seems source error, it should be read as "The other item
of the county is high-lighted.". Please verify. (ex. France)
36
Genre
▲
English
Navigation Help Area
• Default Highlight : All
Mode Change Interaction 1 (1/2)
• This page is only to indicate possible interactions. It may not be exactly identical to actual screens.
My Channel
My Channel
Current status : All Country/Sports
Country
Current status : All Country/Sports
Genre
Country
▲
Genre
▲
DOWN
All Country
All
Austria
News
All Country
All
Austria
News
Belgium (Dutch)
Radio
Belgium (Dutch)
Radio
Belgium (French)
Entertainment
Belgium (French)
Entertainment
Czech
Sports
Czech
Sports
France
Hotel
France
Hotel
LEFT
Germany
Germany
▼
▼
Navigation Help Area
Navigation Help Area
• Current Genre Mode : All Country / Sports
ENTER / RIGHT
My Channel
My Channel
Current status : All Country/Sports
Country
Current status : All Country/Sports
Genre
Country
▲
ENTER
Genre
▲
All Country
All
Austria
News
UP
All Country
All
Austria
News
Belgium (Dutch)
Radio
Belgium (Dutch)
Radio
Belgium (French)
Entertainment
Belgium (French)
Entertainment
Czech
Sports
Czech
Sports
France
Hotel
France
Hotel
DOWN
Germany
Germany
▼
▼
Navigation Help Area
Navigation Help Area
• If the country is selected, highlight moves to genre menu
automatically.
ENTER / RIGHT
6
English
37
Mode Change Interaction 1 (2/2)
• This page is only to indicate possible interactions. It may not be exactly identical to actual screens.
5
1
6
My Channel
Current status : All Country/Sports
ENTER
Country
1
Info
Genre
▲
Genre Mode change to Austria/News.
OK
All Country
All
Austria
News
Belgium (Dutch)
Radio
Belgium (French)
Entertainment
Czech
Sports
France
Hotel
Germany
▼
Navigation Help Area
• The genre mode change complete message is displayed.
• Timeout(5 sec.)
ENTER / RETURN / Timeout
Current Status : Austria / News
38
English
• Pressing the left key from the genre to country menu highlights an
existing selected country item.
Mode Change Interaction 2 (1/2)
• This page is only to indicate possible interactions. It may not be exactly identical to actual screens.
1
My Channel
My Channel
Current status : All Country/Sports
Country
Current status : All Country/Sports
Genre
▲
All Country
All
Austria
News
Country
DOWN
Genre
▲
All Country
All
Austria
News
Belgium (Dutch)
Radio
Belgium (Dutch)
Radio
Belgium (French)
Entertainment
Belgium (French)
Entertainment
Czech
Sports
Czech
Sports
France
Hotel
France
Hotel
UP x 5
Germany
Germany
▼
▼
Navigation Help Area
Navigation Help Area
• Current Genre Mode : All Country / Sports
ENTER / RIGHT
My Channel
Current status : All Country/Sports
Country
101
Info
Genre
▲
Genre Mode change to Austria/News.
OK
BLUE
/
RETURN
/
EXIT
All Country
All
Austria
News
Belgium (Dutch)
Radio
Belgium (French)
Entertainment
Czech
Sports
France
Hotel
Germany
▼
Navigation Help Area
5
ENTER
/
RETURN
/
Timeout
• If the country is selected, highlight moves to genre menu
automatically.
Current Status : Austria / News
• Current Genre Mode : All Country / Sports
English
39
Power On Scenario [Last Memory]
• This page is only to indicate possible interactions. It may not be exactly identical to actual screens.
1
Current Status : Austria / News
POWER
Power Off
• Current Genre Mode : Austria / News
POWER
My Channel
Current status : All Country/Sports
Country
Genre
▲
All Country
All
Austria
News
Belgium (Dutch)
Radio
Belgium (French)
Entertainment
Czech
Sports
France
Hotel
Germany
▼
Navigation Help Area
• Current Genre Mode : Austria / News
40
English
Genre Editor: This configures the genres of each of the hotel TV channels.
• This can be used through the Hotel Menu (Factory).
• Supported genres include News, Radio, Entertainment, Sports and Hotel.
• More than one genre can be selected for each channel at the same time.
Country Editor (Channel Editor): This is the editor that configures the country for each of the hotel TV channels.
• Supported countries (20 countries): Austria, Belgium, China, Denmark, Finland, France, Germany, Greece, Italy, Japan,
Netherlands, Norway, Portugal, Russia, Korea, Spain, Sweden, Turkey, USA
• If more than one channel is set to a country, the country is registered as a category and users can view the channels by
country.
• More than one country can be set to a channel. If the user selects a category, only the channels corresponding to the
country are displayed in the channel list.
• If any channel for which the country is set is selected from the channel list, the Edit Countries item is added to the Tools.
Otherwise, the Add to Countries item is added to the Tools.
• * If the corresponding function is executed, a country for the selected channel can be set or canceled.
• Front UI
• Provides the screen where the user can select a country or genre when the user turns the power on.
Left Frame Layout
Key Guide
Button
Action
Nav. Help
ENTER
Selects or enters the corresponding Channel Browser area.
(No Guide)
RETURN
Selects or enters the corresponding Channel Browser area.
Return
UP/DOWN
Moves the highlight up or down.
(No Guide)
RIGHT
Moves the highlight to the Channel Browser area.
(No Guide)
INFO
Shows the Category Info.
(No Guide)
TOOLS
Shows the utility function menus.
Tools
EXIT
Cancels and returns to the previous step (Factory Mode).
(No Guide)
✎✎ NOTE
• This is a component of the Left Frame (Country Categories).
✎✎ ETC.
• Default Highlight: ‘The currently selected country’
English
41
Elements
No
Name
Description
• When the user enters this screen, the currently selected default item is highlighted.
• The Country Icon + Category Name are provided. (If the highlight is in the Main Frame, only the
icon is displayed.)
• Moving the highlight
−− Pressing the up or down button moves the highlight.
1
−− If the items cannot be displayed on one page, up and down indicators are provided.
−− Once the highlight is moved to a category, the channel list corresponding to the
corresponding category is loaded to the Main Frame.
Left Frame [Country Categories]
Standard
Hotel
Category
Ch. Mode
Original Tuned
Country
Antenna Mode Activation
Air/Cable
Satellite
Registered
O
O
All Country
O
O
Country 1
O
O
Country 2
O
O
.
O
O
Description
• Lists all the channels registered by the Auto
Tune operation.
• Provides the list of channels and sources
specified in the Registered Channels list.
• All Country is the sum of all channels registered
to each country. (This is only provided to end
users.)
•
Tools [Registered/Countries Categories]
• Channel Manager > Channel Category > Tools > Info
• The items are displayed without ‘Channel’.
• If the Registered/Country item in the Left Frame is
highlighted, you can enable the corresponding window
by pressing the ‘INFO’ remote control key.
• All countries are displayed.
• navigate country items by pressing the up or down key.
Indicators are provided.
42
English
✎✎ NOTE
• This is a definition of the Tools menu in the Left Frame Category.
• Only the Info item for each Register/Country is provided.
Elements
Category
Tools menu
Descriptions
Registered, Country
Information
Registered Channels. The number of channels of each country.
• The items are displayed without ‘Channel’.
Error Cases
✎✎ NOTE
• This is the message for when there are no saved channels in the Registered Channels list.
Elements
No
1
Name
Message
Description
• When entering the browser, if the Registered channels item is empty,
a popup message is displayed which enables users to switch to the
Auto Store (Programme) menu.
• When both the time and the channel are not configured, and a user
enters the Channel Manager, a message that allows the user to switch
to the Auto Tuning (Auto Program) operation is displayed in the same
way as above.
• This is the message when the time is not configured.
−− If the time is not configured, the message is displayed in Factory Mode before entering the Channel Manager.
English
43
✎✎ NOTE
• This is the component for when there are no channels registered to the country category.
Elements
No
Description
Description
The message is displayed when the currently selected country does not contain any items.
Main Frame [Channel Browser]
44
English
Key Guide
Button
Action
Nav. Help
CH UP/DOWN
Moves the page.
Page
ENTER
Selects or enters the corresponding Channel Browser area.
Select
RETURN
Returns to the previous step (Factory Mode).
Return
UP/DOWN
Moves the highlight up or down.
(No Guide)
RIGHT
Moves the highlight to the Channel Browser area.
(No Guide)
INFO
Shows the Category Info.
(No Guide)
TOOLS
Shows the utility function menus.
Tools
EXIT
Cancels and returns to the previous step (Factory Mode).
(No Guide)
✎✎ NOTE
• This is a component of the Main Frame (Channel Browser).
• The initial highlight is on the channel before entering Factory Mode or the external input.
Elements
No
Name
1
Main Frame
2
Scroll Bar
3
Navigation Help Area
• This is displayed whenever a user enters the Channel Manager. (If a user exits and then
reenters the Channel Manager, it is displayed again.)
• This disappears when the timeout (5 sec.) is reached or a user presses a key.
4
Navigation Help Area
• The currently configured country information and the RED buttons are left-aligned. They
are displayed and navigated by group graphically. The key guide is right-aligned.
Description
• Shows the channel or the source list of the currently selected category.
• Shows the position of the current page amongst the total amount of pages.
English
45
Channel Common Elements [+ Icon-method]
Channel list representation rules
Standard
Item
Construction
Digital channels
• Check Box + Status Icon + Digital Channel Number + Channel Name
• Channel number representation format: ###-### (The channel number is
represented by ‘-’.)
Analog channels
• Check Box + Analog Icon + Analog Channel Number + Channel Name
• Channel number representation format: ### (‘-’ is not used to represent analog
channel numbers.)
ATSC
• Check Box + Status Icon + Digital Channel Number + Channel Name
Digital channels
• Channel number representation format: ### (For the maximum length of the
channel number, follow the regional specifications.)
DVB (CHEM)
• Check Box + Analog Icon + Analog Channel Number + Channel Name
Analogue channels
• Channel number representation format: ### (For the maximum length of the
channel number, follow the regional specifications.)
Channel list icon representation rules
Item
Example
Dynamic SI
Icon
Channels deleted by
Dynamic SI
Channels added by
Dynamic SI
Analogue Channel Icon
Priority
NNNNNNNN CH. NAME
• Channels that have been deleted by the Dynamic SI
but not by the user.
1
NNNNNNNN CH. NAME
• Channels that have been added by the Dynamic SI
but not by the user.
2
• The Analogue channel icon is displayed.
3
• A channel that is an input source.
4
• Represents the live channels from the antennas.
The Air, Cable or Satellite antenna icons are
displayed with the lowest priority.
5
NNNNNNNN CH. NAME (The
edited channel name.)
Source Channel Icon
Antenna Icon
NNNNNNNN CH. NAME
Air
NNNNNNNN CH. NAME
Cable
NNNNNNNN CH. NAME
Satellite
NNNNNNNN CH. NAME
Scrambled Channel Icon
NNNNNNNN CH. NAME
Video Mute
NNNNNNNN CH. NAME
46
English
• The scrambled channel icon. This appears for the
Satellite antenna.
• A screen-muted channel. Audio and channel
information is provided.
-
Add to Countries / Edit Countries (1/2)
• Channel Manager > Browser > Tools > Add to Countries
Key Guide
Button
Action
Nav. Help
ENTER
Selects the highlighted item.
Enter
RETURN
Cancels and returns to the previous screen (Tools).
Return
UP/DOWN
Moves the highlight over country items.
Move
LEFT/RIGHT
Moves the highlight.
Move
INFO
N/R
N/R
TOOLS
Closes the current window and displays the ‘Tools’ menu.
(No Guide)
EXIT
Cancels and returns to the previous step (Factory Mode).
(No Guide)
✎✎ NOTE
• This is the definition of Add to Countries.
• The highlighted channel or more than one selected channel is added to the Country category.
✎✎ ETC.
• Timeout (60 sec)
English
47
Elements
No
Name
Add to Countries
1
Window
2
Description
• If there are no channels that have been registered to the country list in the
selected channels, “Add to Countries” is displayed as the title.
• A check box is displayed depending on whether the country that was
selected when entering the screen is registered or not.
Guide
• The number of the selected channel or the channel name.
3
Selection Info
4
Complete Message
5
Selection Mark
- The channel name is displayed when one channel has been
selected: Selected channel: NNNN-NNN ABC
- The number of selected channels is displayed when more than one
channel has been selected: Selected Channels : N
• The message is displayed after the completion of the operation. (This
message is always displayed if the OK button is selected.)
• How to identify the meaning of multiple channel selection marks
• When all of the items have been registered.
• When only part of the items have been registered.
• When none of the items have been registered.
Add to Countries / Edit Countries (2/2)
• Channel Manager > Browser > Tools > Add to Countries
Key Guide
Button
Action
Nav. Help
ENTER
Selects the highlighted item.
Enter
RETURN
Cancels and returns to the previous screen (Tools).
Return
UP/DOWN
Moves the highlight over country items.
Move
LEFT/RIGHT
Moves the highlight.
Move
INFO
N/R
N/R
TOOLS
Closes the current window and displays the ‘Tools’ menu.
(No Guide)
EXIT
Cancels and returns to the previous step (Factory Mode).
(No Guide)
48
English
✎✎ NOTE
• This is the definition for Edit Countries.
• The highlighted channel item or more than one selected channel item is added or deleted from the Country category.
• Timeout (60 sec)
Elements
No
Name
1
Add to Countries
2
Guide
3
Complete Message
Description
• If there is a registered channel among the selected channels, Edit Countries
is displayed as the title.
• A check box is displayed depending on whether the selected country is
registered or not.
•
• The message is displayed after the completion of the operation. (This
message is always displayed if the OK button is selected.)
Edit Channel Number [Swap Type]
• Channel Manager > Browser > Tools > Edit Channel Number
Key Guide
Button
Action
Nav. Help
ENTER
Applies the changes and closes the window.
Enter
RETURN
Cancels and returns to the previous screen (Tools).
Return
U/D
Changes the channel number of the selected channel.
Adjust
0~9
Enters a digit.
Number
INFO
N/R
N/R
TOOLS
Closes the current window and displays the ‘Tools’ menu.
(No Guide)
EXIT
Cancels and returns to the previous step (Factory Mode).
(No Guide)
✎✎ NOTE
• This is the function that changes the channel number. (Swap Type)
• Channel numbers can be changed in all the channel lists and changes are applied to all the channels.
• If the new channel number has not been allocated to another channel, the channel number is updated to the new
channel number and the list is sorted again in ascending order of channel number.
• If the new channel number has already been allocated to another channel, follow the Hotel specifications.
✎✎ ETC. Vertical circulation is supported.
English
49
Elements
No
Name
Description
• Both the numeric keys and the Up/Down keys are supported.
−− Selected Channel: Shows the currently selected channel name.
1
Edit Channel
Number Window
−− Number: Shows the new channel number.
(The currently allocated channel name is also displayed.)
−− Name: Shows the currently allocated channel name. (If there are
no channels, it is displayed as “(Empty)”.) : If there is a channel but it
does not have a name, the name is represented as “-----”.
2
Warning
Message
• If an already allocated channel is selected
−− If the new channel number has already been allocated to another
channel, the confirmation message pops up. (Refer to the figure
below.)
−− If the user wants to change the channel number to one that has
already been allocated to another channel, the channel numbers are
swapped and saved.
Edit the Channel Number [External Input] (3/3)
• Channel Manager > Browser > Tools > Edit Channel Number
50
English
Key Guide
Button
Action
Nav. Help
RED
If a user presses the button, the channel number is initialized.
Reset
ENTER
Applies the changes and closes the window.
Enter
RETURN
Cancels or returns to the previous screen (Tools).
Return
U/D
Changes the channel number of the selected channel.
Adjust
0~9T
Enters a digit.
Number
INFO
N/R
N/R
TOOLS
Closes the current window and displays the ‘Tools’ menu.
(No Guide)
EXIT
Cancels and returns to the previous step (Factory Mode).
(No Guide)
✎✎ NOTE
• This function allocates an external input source to a channel number. (The changes are applied to all the channels.)
• If the new channel number has already been allocated to another channel, follow the Hotel specifications.
✎✎ ETC.
• Default Highlight: Channel number area.
• Vertical circulation is supported.
• Timeout (60 sec)
Elements
No
Name
Description
• The channel number area.
−− Both the numeric keys and the Up/Down keys are supported.
−− If no value is allocated, as many ‘-’ are displayed as the number of digits.
1
Channel Number Area
▲
-▼
▲
→
1
▲
→
▼
2
Source Name
• External input name
−− Items that cannot be configured are disabled.
3
Nav. Help Area
• If a user presses the red button, the channel number is initialized.
15
▼
English
51
Edit Channel Name
• Channel Manager > Browser > Tools > Edit Channel Name
Key Guide
Button
Action
Nav. Help
GREEN
Saves the changes and returns to the Channel Manager.
Done
ENTER
Saves the channel name and moves the cursor to the next field.
Enter
RETURN
Cancels and returns to the previous screen (Tools).
Return
U/D/L/R
Navigates on the keyboard.
Move
0~9
Enters a digit.
(No Guide)
INFO
N/R
N/R
TOOLS
Closes the current window and displays the ‘Tools’ menu.
(No Guide)
EXIT
Cancels and returns to the previous step (Factory Mode).
(No Guide)
✎✎ NOTE
• This is the definition of the keypad that is used for the Edit Channel Name function.
✎✎ ETC.
• Timeout (60 sec)
Elements
No
Name
1
Channel Name Edit Window
2
Channel Name
3
Keyboard
52
English
Description
• The cursor and the character that are currently being entered are in the same colour as the
highlight.
• When the maximum number of characters is reached, the cursor disappears.
• For a detailed scenario, refer to the keypad design document.
Tools [Edit Mode]
Edit Mode
Content Highlight (when the number of the checked item is 0 or 1)
When there is more than one checked item.
Add to Countries
Edit Countries (when an already-registered item is
checked.)
Channel Name Edit
Edit Channel Number
Video Mute
Channel Copy (Astra HD +)
Reorder (Satellite)
Select All
Deselect All (this is only displayed when 1 or more items are
selected)
Add to Countries
Edit Countries (when an already-registered item is
checked.)
Video Mute
Reorder (Satellite)
Select All
Deselect All
Delete
Delete
✎✎ NOTE
• The position of the popup menu: The Tools menu for an item in the left column of the Channel List → This is
displayed on the right. The Tools menu for an item in the right column of the Channel List → This is displayed on the
left.
• If a user presses the Tools button when the highlighted item is not selected, the item is automatically marked as
selected.
• For detailed specifications of each function, refer to the NEO Channel Manager.
English
53
CH Banner [when a channel number is allocated to an external input]
✎✎ NOTE
• The TV channel banner specifications are applied.
• When there is an unsupported item or there is no corresponding information, the item values are not displayed.
• The channel name is represented as the ‘external input name’.
Elements
No
Name
1
External Input Name
Description
The Channel List provides access to functions related to GenreTV.
• Country Mode
• Changes the genre mode.
Mixed Channel Map
Mixed Channel Map is a function to mix Air, Cable and Satellite channels.
[ Except for Aus, Singapore, NZ models ]
−− Mixed channel Map should be ON in order to mix Air, Cable and Satellite channels.
−− Use Channel Editor to sort the channels after turning on 'Mixed channel Map' in Hotel Option Menu.
54
English
Sound Bar
• Samsung Sound-Bars and Hospitality TV
−− Use Samsung Sound-Bars and hospitality TVs support the ARC feature in HDMI 1.4. If you connect a compatible
Samsung Sound-Bar to a compatible Samsung hospitality TV using a single HDMI cable, guests can listen to
theTV’s sound through the Sound-Bar.
−− Models supporting the ARC function are listed below:
• Sound-Bars: HW-H450/H550/H570/H600/H7500
HW-J450/J470/J550/J6000
• Setting the Sound-Bars to Hotel Mode.
1. Set the following Hotel menu options:
−− Hotel option > External Device > Sound Bar Out = On.
−− Hotel option > Power On > Power On Volume EN = User Defined.
−− Hotel option > Power On > Power On Volume > Set greater than 0.
−− Hotel option > Power On > Max Volume > Set greater than 0.
2.Connect an HDMI cable from the HDMI OUT jack on the back of Sound-Bar to the HDMI1 port (supporting ARC)
on the hospitality TV.
3.After the Sound-Bar is connected to the hospitality TV, when the TV turns on, the Sound-Bar automatically
detects the TV, and then automatically switches to Hotel Mode.
Sound Bar Hotel mode functional characteristics:
•
•
•
•
•
Power On/Off is synchronized with the TV
HDMI_CEC defaults to On
Functions through the “HDMI OUT” port only
Disables the “Input mode” key on the VFD to prevent unexpected audio-source changes.
Acquires adjustable Power On and Max Volume settings from the TV’s Hotel option menu. The Sound-Bar’s Power
On Volume and Max Volume values, however, are ½ of the Power On Volume and Max Volume settings in the TV’s
Hotel option menu.
Example: If the TV’s Power On Volume=20 and Max Volume=90, then the Sound Bar’s Power On Volume=10 and
Max Volume=45.
*This function may differ depending on the model.
Security mode
Design Specifications
• This is to restrict some functions such as TTX and external source (HDMI, USB) input in specific facilities such as a
correctional facility.
• The Security menu is password-protected. Access to the Security menu is denied without the password.
• Security Setting
−− The Security Setting can be set to ONor OFF.
−− The default is OFF.
−− Security Setting: If set to On, external source (HDMI, USB) input and the TTX function will be disabled.
• Password Setting
−− This allows users to change the password.
−− Users must input the current password, a new password, and confirmation of the new password.
• Password Reset
−− This is to reset the password.
−− The default password is "00000000".
−− Password Reset is visible only in the Factory menu by using the key combination of Info and Factory.
It is not visible using the key combination of MUTE + 1 + 1 + 9 + ENTER.
• Security Setting: If set to On, the SIRCH function is not available.
• Factory Reset will not reset the Security Setting.
English
55
Installing the Wall Mount
The wall mount kit (sold separately) allows you to mount the TV on the wall. For detailed information on installing the wall
mount, see the instructions provided with the wall mount. Contact a technician for assistance when installing the wall mount
bracket. We do not advise you to do it yourself.
Samsung Electronics is not responsible for any damage to the product or injury to yourself or others if you select to install
the TV on your own.
Wall Mount Kit Specifications (VESA)
✎✎ The Wall mount kit is not supplied but sold separately.
Install your wall mount on a solid wall, perpendicular to the floor. When attaching to other building materials, please contact
your nearest dealer. If installing on a ceiling or slanted wall, it may fall and result in severe personal injury.
✎✎ NOTE
• Standard dimensions for wall mount kits are shown in the table below.
• When purchasing our wall mount kit, a detailed installation manual and all parts necessary for assembly are provided.
• Do not use screws that do not comply with VESA standard screw specifications.
• Do not use screws longer than the standard dimensions, as they may cause damage to the inside of the TV set.
• For wall mounts that do not comply with the VESA standard screw specifications, the length of the screws may differ
depending on their specifications.
• Do not fasten the screws too tightly. This may... damage the product or cause the product to fall, leading to personal
injury. Samsung is not liable for these kinds of accidents.
• Samsung is not liable for product damage or personal injury when a non-VESA or non-specified wall mount is used or
the consumer fails to follow the product installation instructions.
• Do not exceed a 15 degrees tilt when mounting this TV.
inches
VESA Spec. (A * B)
Standard Screw
Quantity
32~40
200 X 200
M8
4
Do not install your Wall Mount Kit while your TV is turned on. It may result in personal injury due to electric
shock.
56
English
Securing the TV to the Wall
[
Caution: Pulling, pushing, or climbing onto the TV may cause the TV to fall. In particular, ensure that your children do not
hang over or destabilize the TV; doing so may cause the TV to tip over, resulting in serious injuries or death. Follow all safety
precautions provided on the included Safety Flyer. For added stability, install the anti-fall device for safety purposes, as follows.
To avoid the TV from falling
1. Put the screws into the clamps and firmly fasten them onto the wall. Confirm that the screws have been firmly installed
onto the wall.
✎✎ You may need additional material, such as an anchor, depending on the type of wall.
✎✎ Since the necessary clamps, screws, and string are not supplied, please purchase these additionally.
2. Remove the screws from the centre back of the TV, put the screws into the clamps, and then fasten the screws onto the
TV again.
✎✎ Screws may not be supplied with the product. In this case, please purchase the screws of the following
specifications.
3. Connect the clamps fixed onto the TV and the clamps fixed onto the wall with a strong string and then tie the string
tightly.
✎✎ NOTE
• Install the TV near to the wall so that it does not fall backwards.
• It is safe to connect the string so that the clamps fixed on the wall are equal to or lower than the clamps fixed on
the TV.
• Untie the string before moving the TV.
4. Verify that all connections are properly secured. Periodically check connections for any sign of fatigue for failure. If you
have any doubt about the security of your connections, contact a professional installer.
Anti-theft Kensington Lock
The Kensington Lock is not supplied by Samsung. It is a device used to
physically fix the system when using it in a public place. The appearance and
locking method may differ from the illustration, depending on the manufacturer.
Refer to the manual provided with the Kensington Lock for additional
information on proper use.
To lock the product, follow these steps:
Please find the “K” icon on the rear of the TV. A kensington slot is beside the
“K” icon.
1
<Optional>
1. Wrap the Kensington lock cable around a large, stationary object such as
desk or chair.
2. Slide the end of the cable with the lock attached through the looped end of the Kensington lock cable.
3. Insert the locking device into the Kensington slot on the product (1).
4. Lock the lock.
✎✎ These are general instructions. For exact instructions, see the User manual supplied with the locking device.
✎✎ The locking device has to be purchased separately.
✎✎ The location of the Kensington Lock may be different depending on the model.
English
57
Specifications
Display Resolution
Environmental Considerations
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
Stand Swivel (Left / Right)
Model Name
Screen Size (Diagonal)
Sound (Output)
Dimensions (WxDxH)
Body
With stand
Weight
Without Stand
With Stand
1920 x 1080
10°C to 40°C (50°F to 104°F)
10% to 80%, non-condensing
-20°C to 45°C (-4°F to 113°F)
5% to 95%, non-condensing
0˚
HG32AD590
80 cm
HG40AD590
100 cm
10W x 2
73.8 x 9.3 x 44.4 cm
73.8 x 19.1 x 49.8 cm
90.5 x 9.1 x 52.5 cm
90.5 x 19.6 x 56.2 cm
5.9 kg
6.6 kg
6.4 kg
7.3 kg
✎✎ Design and specifications are subject to change without prior notice.
✎✎ For power supply and power consumption information, refer to the label attached to the product.
58
English
Dimensions
Front view / Side view
4
1
2
3
5
(Unit: cm)
1
2
3
4
5
HG32AD590
73.8
44.4
49.8
9.3
19.1
HG40AD590
90.5
52.5
56.2
9.1
19.6
English
59
Jack panel detail / Rear view
5
6
8
7
(Unit: cm)
1
2
3
4
5
6
7
8
HG32AD590
20.0
20.0
26.9
11.6
18.9
8.8
10.5
48.3
HG40AD590
20.0
20.0
33.7
5.0
24.4
18.9
16.0
57.8
60
English
Base Stand detail
HG32AD590
(Unit: cm)
5.5
13.5
R0.9
R0.3
15.2
41.9
19.1
16.4
HG40AD590
(Unit: cm)
38.3
15.1
✎✎ NOTE: All drawings are not necessarily to scale. Some dimensions are subject to change without prior notice. Refer to
the dimensions prior to performing installation of your TV. Not responsible for typographical or printed errors.
English
61
Licence
Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are
trademarks of Dolby Laboratories.
Manufactured under a license from U.S. Patent No’s: 5,956,674, 5,974,380, 5,978,762,
6,487,535, 6,226,616, 7,212,872, 7,003,467, 7,272,567, 7,668,723, 7,392,195,
7,930,184, 7,333,929 and 7,548,853. DTS, the Symbol, and DTS and the Symbol
together are registered trademarks & DTS Premium Sound is a trademark of DTS, Inc.
©2012 DTS, Inc. All Rights Reserved.
Manufactured under a license from U.S. Patent No’s: 6,285,767, 8,027,477, 5,319,713,
5,333,201, 5,638,452, 5,771,295, 5,970,152, 5,912,976, 7,200,236, 7,492,907,
8,050,434, 7,720,240, 7,031,474, 7,907,736 and 7,764,802. DTS, the Symbol, and DTS
and the Symbol together are registered trademarks & DTS Studio Sound is a trademark
of DTS, Inc. ©2012 DTS, Inc. All Rights Reserved.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are
trademarks or registered trademarks of HDMI Licensing LLC in the United States and
other countries.
DivX Certified® to play DivX® video up to HD 1080p, including premium content.
ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary of Rovi Corporation. This is an
official DivX Certified® device that has passed rigorous testing to verify that it plays DivX video. Visit divx.com for more
information and software tools to convert your files into DivX videos.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered in order to play purchased DivX Videoon-Demand (VOD) movies.
To obtain your registration code, locate the DivX VOD section in your device setup menu. Go to vod.divx.com for more
information on how to complete your registration.
DivX®, DivX Certified® and associated logos are trademarks of Rovi Corporation or its subsidiaries and are used under
license.
Covered by one or more of the following U.S. patents: 7,295,673; 7,460,668; 7,515,710; 7,519,274
Open Source License Notice
Open Source used in this product can be found on the following webpage. (http://opensource.samsung.com)
Open Source Licence Notice is written only English.
62
English
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care centre.
Country
Customer Care Centre
1800-SAMSUNG(726-7864)
1300 362 603
0800 726 786
1800 588 889
Web Site
www.samsung.com/th/support
ALGERIA
IRAN
SAUDI ARABIA
0-2689-3232,
1800-29-3232
+95-1-2399-888
+855-23-993232
+856-214-17333
1800-88-9999
603-77137477 (Overseas contact)
021-56997777
08001128888
1-800-10-726-7864 [ PLDT Toll Free ]
1-800-8-726-7864 [ Globe Landline and Mobile ]
02- 422-2111 [ Standard Landline ]
0800-329999
0120-363-905
1800 40 SAMSUNG (1800 40 7267864) (Toll-Free)
18000910113
0961-2300300
0800-0300300 (Toll Free)
0115900000
08000-7267864
16580
3004
021-8255 [CE]
800 247 3457 (800 24/7 HELP)
PAKISTAN
TUNISIA
0800-Samsung (72678)
80 1000 12
U.A.E
OMAN
KUWAIT
BAHRAIN
QATAR
TURKEY
JORDAN
800-SAMSUNG (800 - 726 7864)
800-SAMSUNG (800 - 726 7864)
183-CALL (183-2255)
8000-GSAM (8000-4726)
800-CALL (800-2255)
444 77 11
0800-22273
06 5777444
962 5777444
961 1484 999
1299
964 77 261 72220
964 75 118 92525
080 100 22 55
SINGAPORE
AUSTRALIA
NEW ZEALAND
VIETNAM
THAILAND
MYANMAR
CAMBODIA
LAOS
MALAYSIA
INDONESIA
PHILIPPINES
TAIWAN
JAPAN
INDIA
NEPAL
BANGLADESH
SRI LANKA
EGYPT
SYRIA
LEBANON
IRAQ
MOROCCO
© 2015 Samsung Electronics Co., Ltd. All rights reserved.
www.samsung.com/sg/support
www.samsung.com/au/support
www.samsung.com/nz/support
www.samsung.com/vn/support
www.samsung.com/th/support
www.samsung.com/my/support
www.samsung.com/id/support
www.samsung.com/ph/support
www.samsung.com/tw/support
www.samsung.com/jp/support
www.samsung.com/in/support
www.samsung.com/support
www.samsung.com/support
www.samsung.com/support
www.samsung.com/eg/support
www.samsung.com/n_africa/support
www.samsung.com/iran/support
www.samsung.com/sa/home
www.samsung.com/sa_en
www.samsung.com/pk/support
www.samsung.com/n_africa/support
www.samsung.com/ae/support (English)
www.samsung.com/ae_ar/support (Arabic)
www.samsung.com/tr/support
www.samsung.com/levant/support
www.samsung.com/n_africa/support
AD590_Asia_ENG-03
Download PDF

advertising