advertisement
▼
Scroll to page 2
of 43
FULL MANUAL HW-N850 Imagine the possibilities Thank you for purchasing this Samsung product. To receive more complete service, please register your product at www.samsung.com/register SAFETY INFORMATION SAFETY WARNINGS WARNING •• To reduce the risk of fire or electric shock, do TO REDUCE THE RISK OF ELECTRIC SHOCK, DO not expose this appliance to rain or moisture. NOT REMOVE THE COVER (OR BACK). CAUTION NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE •• TO PREVENT ELECTRIC SHOCK, MATCH WIDE PERSONNEL. BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. •• This apparatus shall always be connected to a CAUTION AC outlet with a protective grounding RISK OF ELECTRIC SHOCK. DO NOT OPEN. connection. •• To disconnect the apparatus from the mains, This symbol indicates that high voltage is present inside. It is dangerous to make any kind of contact with any internal part of this product. the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable. This symbol indicates that this product has included important literature concerning operation and maintenance. Class II product : This symbol indicates •• Do not expose this apparatus to dripping or splashing. Do not put objects filled with liquids, such as vases on the apparatus. •• To turn this apparatus off completely, you must pull the power plug out of the wall that it does not require a safety connection to electrical earth (ground). AC voltage : This symbol indicates that the rated voltage marked with the symbol is AC voltage. DC voltage : This symbol indicates that the rated voltage marked with the symbol is DC voltage. Caution, Consult instructions for use : This symbol instructs the user to consult the user manual for further safety related information. ENG - ii socket. Consequently, the power plug must be easily and readily accessible at all times. PRECAUTIONS 5. The battery used with this product contains chemicals that are harmful to the environment. Do not dispose of the battery 1. Ensure that the AC power supply in your in the general household trash. Do not house complies with the power expose the battery to excess heat, direct requirements listed on the identification sunlight, or fire. Do not short circuit, sticker located on the bottom of your disassemble, or overheat the battery. product. Install your product horizontally, on Danger of explosion if the battery is replaced a suitable base (furniture), with enough incorrectly. Replace only with the same or space around it for ventilation (7~10 cm). equivalent type. Make sure the ventilation slots are not covered. Do not place the unit on amplifiers or other equipment which may become hot. This unit is designed for continuous use. To ABOUT THIS MANUAL fully turn off the unit, disconnect the AC plug The user manual has two parts: this simple paper from the wall outlet. Unplug the unit if you USER MANUAL and a detailed FULL MANUAL you intend to leave it unused for a long period of can download. time. 2. During thunderstorms, disconnect the AC plug from the wall outlet. Voltage peaks due to lightning could damage the unit. 3. Do not expose the unit to direct sunlight or USER MANUAL other heat sources. This could lead to See this manual for safety instructions, overheating and cause the unit to product installation, components, malfunction. connections, and product specifications. 4. Protect the product from moisture (i.e. vases), and excess heat (e.g. a fireplace) or equipment creating strong magnetic or electric fields. Unplug the power cable from the AC wall socket if the unit malfunctions. Your product is not intended for industrial use. It is for personal use only. Condensation FULL MANUAL may occur if your product has been stored in You can access the FULL MANUAL on cold temperatures. If transporting the unit Samsung’s on-line customer support centre by during the winter, wait approximately scanning the QR code. To see the manual on 2 hours until the unit has reached room your PC or mobile device, download the temperature before using. manual in document format from Samsung’s website. (http://www.samsung.com/support) Design, specifications, and App screen are subject to change without prior notice. ENG - iii CONTENTS 01 Checking the Components 2 Inserting Batteries before using the Remote Control (AA batteries X 2) -------------------------- 2 02 03 04 05 Product Overview 3 Front Panel / Top Panel of the Soundbar -------------------------- 3 Bottom Panel of the Soundbar -------------------------- 4 Connecting the Soundbar 5 Connecting Electrical Power -------------------------- 5 Connecting the Soundbar to the Subwoofer –– Automatic connection between the Subwoofer and the Soundbar –– Manually connecting the Subwoofer if automatic connection fails -------------------------- 6 -------------------------- 6 -------------------------- 7 Connecting the SWA-9000S to a Soundbar (Sold Separately) -------------------------- 8 Connecting to a TV 10 Method 1. Connecting with a Cable –– Connecting a TV using an HDMI Cable –– Connecting using an Optical Cable -------------------------- 10 -------------------------- 10 -------------------------- 11 Method 2. Connecting Wirelessly –– Connecting a TV via Bluetooth –– Connecting via Wi-Fi -------------------------- 12 -------------------------- 12 -------------------------- 14 Connecting an External Device 16 Connecting using an HDMI Cable (Dolby Atmos® supported) -------------------------- 16 Connecting using an HDMI Cable -------------------------- 17 Connecting using an Optical Cable -------------------------- 18 ENG - iv 06 07 08 09 10 Connecting a Mobile Device 19 Connecting via Bluetooth -------------------------- 19 Connecting via Wi-Fi (Wireless Network) -------------------------- 22 Connecting an Amazon product 24 Connect and use with an Amazon product (Amazon Echo) -------------------------- 24 Use voice commands to control the Soundbar -------------------------- 26 Using the Remote Control 27 How to Use the Remote Control -------------------------- 27 Adjusting the Soundbar volume with a TV remote control -------------------------- 30 Using the Hidden Buttons (Buttons with more than one function) -------------------------- 31 Output specifications for the different sound effect modes -------------------------- 31 Installing the Wall Mount 32 Installation Precautions -------------------------- 32 Wallmount Components -------------------------- 32 Software Update 34 11Troubleshooting 35 12Licence 36 13 Open Source Licence Notice 37 14 Important Notes About Service 37 15 Specifications and Guide 38 Specifications -------------------------- 38 ENG - v 01 CHECKING THE COMPONENTS PAIR SOUND MODE VOL WOOFER SOUNDBAR Soundbar Main Unit 1 Remote Control / Batteries Subwoofer 2 x2 Power Cord (Subwoofer) Power Cord (Main Unit) x2 HDMI Cable Bracket-Wall Mount x2 (M4 x L10) Wall Mount Guide Holder-Screw Screw •• For more information about the power supply and power consumption, refer to the label attached to the product. (Label : Bottom of the Soundbar Main Unit) •• The power components are labelled (1, 2). For more information about power connections, see page 5. •• For Soundbar wall mounting components, see page 32. •• To purchase additional components or optional cables, contact a Samsung Service Centre or Samsung Customer Care. •• The appearance of the accessories may differ slightly from the illustrations above. Inserting Batteries before using the Remote Control (AA batteries X 2) Slide the battery cover in the direction of the arrow until it is completely removed. Insert 2 AA batteries (1.5V) oriented so that their polarity is correct. Slide the battery cover back into position. ENG - 2 02 PRODUCT OVERVIEW Front Panel / Top Panel of the Soundbar Position the product so that the Top Panel "Samsung Harman Kardon" logo is located on the top. (Power) Button Turns the power on and off. (Source) Button Selects the source input mode. Input mode Display Optical Digital input D.IN ARC (HDMI OUT) input D.IN TV ARC (Auto conversion) HDMI input HDMI 1 / HDMI 2 Wi-Fi mode WIFI BLUETOOTH mode BT •• To turn on “BT PAIRING” mode, change the source to “BT” mode, and then press and hold the (Source) button on the top panel for more than 5 seconds. -/+ (Volume) Button Adjusts the volume. •• When adjusted, the volume level appears on the Soundbar’s front display. Display Displays the product’s status and current mode. •• When you plug in the AC cord, the power button will begin working in 4 to 6 seconds. •• When you turn on this unit, there will be a 4 to 5 second delay before it produces sound. •• If you want to enjoy sound only from the Soundbar, you must turn off the TV’s speakers in the Audio Setup menu of your TV. Refer to the owner’s manual supplied with your TV. ENG - 3 DIGITAL AUDIO IN DIGITAL AUDIO IN (OPTICAL) (OPTICAL) Bottom Panel of the Soundbar POWER POWER POWER SERVICE SERVICE DIGITAL AUDIO IN (OPTICAL) SERVICE ID SET (WOOFER/REAR) ID SET (WOOFER/REAR) ID SET (WOOFER/REAR) NETWORK NETWORK NETWORK HDMI IN 1 HDMI IN 1 HDMI IN 1 HDMI IN 2 HDMI IN 2 HDMI IN 2 HDMI OUT (TV-ARC) HDMI OUT (TV-ARC) HDMI OUT (TV-ARC) POWER POWER POWER ID SET ID SET ID SET (WOOFER/REAR) (WOOFER/REAR) (WOOFER/REAR) SERVICE SERVICE SERVICE HDMI HDMI INHDMI IN 1 1 IN 1 HDMI HDMI INHDMI IN 2 2 IN 2 NETWORK NETWORK NETWORK DIGITAL DIGITAL DIGITAL AUDIO AUDIO AUDIO IN IN IN (OPTICAL) (OPTICAL) (OPTICAL) HDMI HDMI OUT HDMI OUT OUT (TV-ARC) (TV-ARC) (TV-ARC) DIGITAL AUDIO IN (OPTICAL) POWER SERVICE ID SET (WOOFER/REAR) HDMI IN 1 NETWORK HDMI IN 2 HDMI OUT (TV-ARC) POWER Connect the Soundbar's AC power cord. POWER SERVICE DIGITAL AUDIO IN (OPTICAL) HDMI IN 1 ID SET ID SET (WOOFER/REAR) (WOOFER/REAR) Press to connect the Soundbar to surround NETWORK speakers and a subwoofer wirelessly. HDMI IN 2 •• Press and hold the Up button on the remote for 5 seconds to complete ID SET. NETWORK Press to connect to a wireless network (Wi-Fi) via the SmartThings app. SERVICE Connect a USB storage device to upgrade the product's software. DIGITAL AUDIO IN (OPTICAL) Connect to the digital (optical) output of an external device. HDMI IN 1 / HDMI IN 2 Inputs digital video and audio signals simultaneously using an HDMI cable. Use when connecting a supported external device. HDMI OUT (TV-ARC) HDMI OUT (TV-ARC) Connect to the HDMI (ARC) jack on a TV. •• When disconnecting the power cord from a wall outlet, pull the plug. Do not pull the cable. •• Do not connect this unit or other components to an AC outlet until all connections between components are complete. ENG - 4 03 CONNECTING THE SOUNDBAR Connecting Electrical Power Use the power components (1, 2) to connect the Subwoofer and Soundbar to an electrical outlet in the following order: 1 Connect the power cord to the Subwoofer. 2 Connect the power cord to the Soundbar. See the illustrations below. •• For more information about the required electrical power and power consumption, refer to the label attached to the product. (Label : Bottom of the Soundbar Main Unit) 1 Power Cord POWER Rear of Subwoofer POWER Connecting Electrical Power POWER 2 Power Cord DIGITAL AUDIO IN (OPTICAL) SERVICE POWER ID SET (WOOFER/REAR) HDMI IN 1 NETWORK HDMI IN 2 HDMI OUT (TV-ARC) Bottom of the Soundbar Main Unit Connecting Electrical Power POWER ID SET (WOOFER/REAR) NETWORK ENG - 5 SERVICE DIGITAL AUDIO IN (OPTICAL) HDMI IN 1 HDMI IN 2 HDMI OUT Connecting the Soundbar to the Subwoofer When the subwoofer is connected, you can enjoy rich bass sound. Automatic connection between the Subwoofer and the Soundbar When you turn the power on after connecting the power cables to the Soundbar and subwoofer, the subwoofer is automatically connected to the Soundbar. •• When auto pairing is complete, the blue indicators at the rear of the subwoofer turn on. LED Indicator Lights on the Rear of Subwoofer LED Status On Blue Blinking Description Successfully connected (normal operation) On Check the power supply to the Soundbar main unit turned off) main unit. Connection failed Connect again. (Refer to the instructions on manual connection on page 7.) main unit turned off) blue Blinking Check the power supply to the Soundbar main unit. Connect again. (Refer to the instructions on Connection failed Red and - Standby (with the Soundbar Standby (with the Soundbar Red Resolution manual connection on page 7.) See the contact information for the Malfunction Samsung Service Centre in this manual. ENG - 6 Manually connecting the Subwoofer if automatic connection fails Before performing the manual connection procedure below: •• Check whether the power cables for the Soundbar and subwoofer are connected properly. •• Make sure that the Soundbar is turned on. 1. Press and hold ID SET on the rear of the subwoofer for at least 5 seconds. •• The red indicator on the rear of the subwoofer turns off and the blue indicator blinks. 5 Sec Blue LED Blinking Fast Rear of Subwoofer 2. Press and hold the Up button on the remote control for at least 5 seconds. •• The ID SET message appears on the display of the Soundbar for a moment, and then it disappears. •• The Soundbar will automatically power on when ID SET is complete. 5 Sec PAIR “Samsung Harman Kardon” logo is on the top ID SET ND SOUODE M 3. Check if the LINK LED is solid blue (connection complete). The LINK LED indicator stops blinking and glows a solid blue when a connection is established between the Soundbar and the Blue is On Wireless Subwoofer. ENG - 7 NOTES •• Do not connect the power cord of this product or your TV to a wall outlet until all connections between components are complete. •• Before moving or installing this product, be sure to turn off the power and disconnect the power cord. •• If the main unit is powered off, the wireless subwoofer will go into stand-by mode and the STANDBY LED on the rear will be Red after blinking Blue several times. •• If you use a device that uses the same frequency (5.8GHz) as the Soundbar near the Soundbar, interference may cause some sound interruption. •• The maximum transmission distance of the wireless signal of the main unit is about 10 meters, but may vary depending on your operating environment. If a steel-concrete or metallic wall is between the main unit and the wireless subwoofer the system may not operate at all, because the wireless signal cannot penetrate metal. PRECAUTIONS •• Wireless receiving antennas are built into the wireless subwoofer. Keep the units away from water and moisture. •• For optimal listening performance, make sure that the area around the wireless subwoofer and Wireless Receiver Module (Sold separately) location is clear of any obstructions. Connecting the SWA-9000S to a Soundbar (Sold Separately) Expand to true wireless surround sound by connecting the Samsung Wireless Rear Speaker Kit (SWA-9000S) to your Soundbar (Sold separately). 1. Connect the Wireless Receiver Module to 2 Surround Speakers. –– The speaker cables are color coded. L SURROUND-LEFT R SURROUND SPEAKERS OUT SPEAKER IMPEDANCE : 3Ω SURROUND-RIGHT ID SET L R SURROUND-LEFT SURROUND-RIGHT SURROUND SPEAKERS OUT SPEAKER IMPEDANCE : 3Ω POWER ID SET ENG - 8 2. Check the standby status of the Wireless Receiver Module after plugging it into an electrical outlet. •• The LINK LED indicator (blue LED) on the Wireless Receiver Module blinks. If the LED does not blink, press the ID SET button on the back of the Wireless Receiver Module with a pen tip for 5~6 seconds until the LINK LED indicator blinks (in Blue). For more about the LED, please refer to the SWA-9000S user manual. STANDBY SURROUND SPEAKERS OUT SPEAKER IMPEDANCE : 3Ω L R 5 Sec SURROUND SPEAKERS OUT SPEAKER IMPEDANCE : 3Ω STANDBY ID SET ID SET LINK LINK POWER Blue blinking POWER 3. Press and hold the Up button on the remote control for at least 5 seconds. •• The ID SET message appears on the display of the Soundbar for a moment, and then it disappears. •• The Soundbar will automatically power on when ID SET is complete. 5 Sec PAIR “Samsung Harman Kardon” logo is on the top ID SET ND SOUODE M CAUTION •• If your Soundbar was playing music when it connects to the SWA-9000S, you may hear some stuttering from the woofer as the connection finalises. 4. Check if the LINK LED is solid blue (connection complete) STANDBY STANDBY LINK The LINK LED indicator stops blinking and glows a solid blue when a connection is LINK established between the Soundbar and the Wireless Receiver Module. Blue is On 5. If SWA-9000S is not connected, repeat the procedure from Step 2. ENG - 9 04 CONNECTING TO A TV Hear TV sound from your Soundbar through wired or wireless connections. •• When the Soundbar is connected to selected Samsung TVs, the Soundbar can be controlled using the TV’s remote control. –– This feature is available on 2017 and later Samsung Smart TVs that support Bluetooth when the Soundbar is connected to the TV using an optical cable. –– This function also allows you to use the TV menu to adjust the sound field and various settings as well as the volume and mute. Method 1. Connecting with a Cable When the audio in a broadcast is encoded in Dolby Digital and the “Digital Output Audio Format” on your TV is set to PCM, we recommend that you change the setting to Dolby Digital. When the setting on the TV is changed, you will experience better sound quality. (The TV menu may use different words for Dolby Digital and PCM depending on the TV manufacturer.) Connecting a TV using an HDMI Cable Connect to the HDMI IN (ARC) port of your TV. HDMI Cable HDMI IN (ARC) Bottom of the Soundbar HDMI OUT (TV-ARC) Connect to the HDMI OUT (TV-ARC) port of the Soundbar main unit. Top of the Soundbar TV ARC 1. With the Soundbar and TV turned on, connect the HDMI cable as shown in the figure. 2. “TV ARC” appears in the display window of the Soundbar main unit and the Soundbar plays TV sound. •• If TV sound is inaudible, press the (Source) button on the remote control or on the top of the Soundbar to switch to “D.IN” mode. The screen displays “D.IN” and “TV ARC” in sequence, and TV sound is played. ENG - 10 •• If “TV ARC” does not appear in the display window of the Soundbar main unit, confirm that the HDMI cable is connected to the correct port. •• Use the volume buttons on the TV’s remote control to change the volume on the Soundbar. NOTES •• HDMI is an interface that enables the digital transmission of video and audio data with just a single connector. •• If the TV provides an ARC port, connect the HDMI cable to the HDMI IN (ARC) port. •• We recommend you use a coreless HDMI cable if possible. If you use a cored HDMI cable, use one whose diameter is less than 14 mm. •• Anynet+ must be turned on. •• This function is not available if the HDMI cable does not support ARC. Connecting using an Optical Cable Optical Cable Bottom of the Soundbar (not supplied) DIGITAL AUDIO IN (OPTICAL) OPTICAL OUT Top of the Soundbar HDMI IN 1 HDMI IN 2 D.IN 1. Connect the DIGITAL AUDIO IN (OPTICAL) jack on the Soundbar to the OPTICAL OUT jack of the TV with a digital optical cable (not supplied). 2. Press the (Source) button on the top panel or on the remote control, and then select the “D.IN” mode. Auto Power Link Auto Power Link automatically turns on the Soundbar when the TV is turned on. 1. Connect the Soundbar and a TV with a digital optical cable (not supplied). 2. Press the Left button on the remote control for 5 seconds to turn Auto Power Link on or off. •• Auto Power Link is set to ON by default. (To turn off this function, press the Left button on the remote for 5 seconds.) •• Depending on the connected device, Auto Power Link may not function. •• This function is only available in the “D.IN” mode. ENG - 11 Method 2. Connecting Wirelessly Connecting a TV via Bluetooth When a TV is connected using Bluetooth, you can hear stereo sound without the hassle of cabling. •• Only one TV can be connected at a time. Top of the Soundbar PAIR OR ND SOUODE M The initial connection 1. Press the PAIR button on the remote control to enter the “BT PAIRING” mode. (OR) a. Press the (Source) button on the top panel and then select “BT”. “BT” changes to “BT READY” in a few seconds automatically if there is no Bluetooth device connected to the Soundbar. b. When “BT READY” appears, press and hold the (Source) button on the top panel of the Soundbar for more than 5 seconds to display “BT PAIRING”. 2. Select Bluetooth mode on the TV. (For more information, see the TV’s manual.) 3. Select “[AV] Samsung Soundbar Nxxx” from the list on the TV’s screen. An available Soundbar is indicated with “Need Pairing” or “Paired” in the TV Bluetooth device list. To connect the TV to the Soundbar, select the message, and then establish a connection. •• When the TV is connected, [TV Name] → “BT” appears on the Soundbar’s front display. 4. You can now hear TV sound from the Soundbar. If the device fails to connect •• If a previously connected Soundbar (e.g. “[AV] Samsung Soundbar Nxxx”) appears in the list, delete it. •• Then repeat steps 1 through 3. ENG - 12 Disconnecting the Soundbar from the TV Press the (Source) button on the top panel or on the remote control and switch to any mode but “BT”. •• Disconnecting takes time because the TV must receive a response from the Soundbar. (The time required may differ, depending on the TV model.) •• To cancel the automatic Bluetooth connection between the Soundbar and TV, press the p (Play/Pause) button on the remote control for 5 seconds with the Soundbar in “BT READY” status. (Toggle On → Off) NOTE •• After you have connected the Soundbar to your TV the first time, use the “BT READY” mode to reconnect. What is the difference between BT READY and BT PAIRING? •• BT READY : In this mode, you can search for previously connected TVs or connect a previously connected mobile device to the Soundbar. •• BT PAIRING : In this mode, you can connect a new device to the Soundbar. (Press the on the remote control or press and hold the PAIR button (Source) button on the top of the Soundbar for more than 5 seconds while the Soundbar is in “BT” mode.) NOTES •• If asked for a PIN code when connecting a Bluetooth device, enter <0000>. •• In Bluetooth connection mode, the Bluetooth connection will be lost if the distance between the Soundbar and the Bluetooth device exceeds 10 meters. •• The Soundbar automatically turns off after 5 minutes in the Ready state. •• The Soundbar may not perform Bluetooth search or connection correctly under the following circumstances: –– If there is a strong electrical field around the Soundbar. –– If several Bluetooth devices are simultaneously paired with the Soundbar. –– If the Bluetooth device is turned off, not in place, or malfunctions. •• Electronic devices may cause radio interference. Devices that generate electromagnetic waves must be kept away from the Soundbar main unit - e.g., microwaves, wireless LAN devices, etc. ENG - 13 Connecting via Wi-Fi Pre-connection Checklist 1. Confirm that your Samsung Smart TV was released after 2013. This function is compatible only with Samsung Smart TVs released after 2013. 2. Make sure your Wireless router (Wi-Fi) is ready and working. 3. Make sure that the TV is connected to the Wireless router (your Wi-Fi network). Top of the Soundbar Step 1 : Connecting the Soundbar to Wi-Fi 1. Press the (Source) button on the top of the Soundbar or on the remote control to select “WIFI” mode. •• When using selected Samsung TVs (2016 ~ 2018 Samsung Smart TVs that support Bluetooth.) –– If you select “WIFI” mode when the TV is turned on, the TV screen displays a pop-up window providing instructions on how to automatically connect the Soundbar to a wireless router (Wi-Fi). Refer to instructions in the pop-up window of the TV. Top of the Soundbar WIFI 2. Connect your mobile device (smartphone, tablet, etc.) to the Wi-Fi network the TV is connected to. 3. Install and launch the SmartThings app on your mobile device (smartphone, tablet, etc.). Android iOS SmartThings app 4. Follow the instructions in the app screen on the mobile device to connect the Soundbar to your Wi-Fi network. ENG - 14 Step 2 : Configuring Settings on the TV •• If the TV disconnects from your wireless network after you change the input source to the Soundbar, use the TV menu to connect the TV to the network again. For TVs released in 2018 Home ( ) Settings ( ) Sound Sound Output [AV] Samsung Soundbar Nxxx (Wi-Fi) For TVs released in 2017 Home ( ) Settings ( ) Sound Sound Output [AV] Samsung Soundbar Nxxx (Wi-Fi) For TVs released in 2016 Home ( ) Settings ( ) Sound Select Speaker [AV] Samsung Soundbar Nxxx (Wi-Fi) For TVs released in 2015 Menu Sound Speaker List For TVs released in 2014 Menu Sound Speaker Settings Multiroom Link - Settings NOTES •• The TV and Soundbar must be connected to the same wireless network (Wi-Fi). •• If your wireless router (Wi-Fi) uses a DFS channel, you will not be able to establish a Wi-Fi connection between the TV and Soundbar. Contact your Internet service provider for details. •• If the 5GHz Wi-Fi connection is not smooth, use the 2.4GHz bandwidth. •• Because the menus may differ depending on the year of manufacture, refer to your TV manual. ENG - 15 05 CONNECTING AN EXTERNAL DEVICE Connect to an external device via a wired or wireless network to play the external device’s sound through the Soundbar. Connecting using an HDMI Cable (Dolby Atmos® supported) •• What is Dolby Atmos®? Atmos technology enhances existing 7.1 channel surround sound systems by adding an overhead speaker. This envelops the listener in 360 degrees of sound, delivering an immersive, high-definition, rich, detailed, and deeper experience. •• Important: This product supports Dolby Atmos® only in HDMI mode. Top of the Soundbar HDMI 1 OR DIGITAL AUDIO IN (OPTICAL) HDMI IN 1 HDMI Cable OR HDMI OUT HDMI IN 2 External Device HDMI IN (ARC) HDMI 2 HDMI Cable HDMI OUT (TV-ARC) Bottom of the Soundbar 1. Connect an HDMI cable from the HDMI IN 1 or HDMI IN 2 jack on the bottom of the Soundbar to the HDMI OUT jack on your digital device. 2. Connect an HDMI cable from the HDMI OUT (TV-ARC) jack on the bottom of the Soundbar to the HDMI IN jack on your TV. 3. Press the (Source) button on the top panel or on the remote control, and then select “HDMI 1” or “HDMI 2”. 4. “HDMI 1” or “HDMI 2” mode is displayed on the Soundbar display panel and sound plays. ENG - 16 NOTE •• When Dolby Atmos® is activated, “DOLBY ATMOS” appears in the front display. Configuring Dolby Atmos® on your BD player or other device. •• Open the audio output options on the settings menu of your BD player or other device and make sure that “No Encoding” is selected for Bitstream. For example, on a Samsung BD Player, go to Home Menu → Sound → Digital Output and then select Bitstream (unprocessed). •• If the Audio Output options include Secondary Audio, make sure Secondary Audio is set to Off. •• Dolby Atmos® works only on 7.1.2 channels. •• Make sure that the content supports Dolby Atmos®. Connecting using an HDMI Cable Top of the Soundbar HDMI 1 OR DIGITAL AUDIO IN (OPTICAL) HDMI IN 1 HDMI Cable OR HDMI OUT HDMI IN 2 External Device HDMI IN (ARC) HDMI 2 HDMI Cable HDMI OUT (TV-ARC) Bottom of the Soundbar 1. Connect an HDMI cable from the HDMI IN 1 or HDMI IN 2 jack on the bottom of the Soundbar to the HDMI OUT jack on your digital device. 2. Connect an HDMI cable from the HDMI OUT (TV-ARC) jack on the bottom of the Soundbar to the HDMI IN jack on your TV. 3. Press the (Source) button on the top panel or on the remote control, and then select “HDMI 1” or “HDMI 2”. 4. “HDMI 1” or “HDMI 2” mode is displayed on the Soundbar display panel and sound plays. ENG - 17 Connecting using an Optical Cable Top of the Soundbar BD / DVD player / Set-top box / Game console D.IN OPTICAL OUT DIGITAL AUDIO IN (OPTICAL) Optical Cable (not supplied) Bottom of the Soundbar 1. Connect DIGITAL AUDIO IN (OPTICAL) on the main unit to the OPTICAL OUT jack of the Source Device using a digital optical cable (not supplied). 2. Select “D.IN” mode by pressing the (Source) button on the top panel or on the remote control. ENG - 18 06 CONNECTING A MOBILE DEVICE Connecting via Bluetooth When a mobile device is connected using Bluetooth, you can hear stereo sound without the hassle of cabling. •• You cannot connect more than one Bluetooth device at a time. Top of the Soundbar PAIR OR Bluetooth device ND SOUODE M The initial connection 1. Press the PAIR button on the remote control to enter the “BT PAIRING” mode. (OR) a. Press the (Source) button on the top panel and then select “BT”. “BT” changes to “BT READY” in a few seconds automatically if there is no Bluetooth device connected to the Soundbar. b. When “BT READY” appears, press and hold the (Source) button on the top panel of the Soundbar for more than 5 seconds to display “BT PAIRING”. 2. On your device, select “[AV] Samsung Soundbar Nxxx” from the list that appears. •• When the Soundbar is connected to the Bluetooth device, [Bluetooth Device Name] → “BT” appears in the front display. 3. Play music files located on the device connected via Bluetooth through the Soundbar. If the device fails to connect •• If a previously connected Soundbar (e.g. “[AV] Samsung Soundbar Nxxx”) appears in the list, delete it. •• Then repeat steps 1 and 2. NOTE •• After you have connected the Soundbar to your mobile device the first time, use the “BT READY” mode to reconnect. ENG - 19 What is the difference between BT READY and BT PAIRING? •• BT READY : In this mode, you can search for previously connected TVs or connect a previously connected mobile device to the Soundbar. •• BT PAIRING : In this mode, you can connect a new device to the Soundbar. (Press the on the remote control or press and hold the PAIR button (Source) button on the top of the Soundbar for more than 5 seconds while the Soundbar is in “BT” mode.) NOTES •• If asked for a PIN code when connecting a Bluetooth device, enter <0000>. •• In Bluetooth connection mode, the Bluetooth connection will be lost if the distance between the Soundbar and the Bluetooth device exceeds 10 meters. •• The Soundbar automatically turns off after 5 minutes in the Ready state. •• The Soundbar may not perform Bluetooth search or connection correctly under the following circumstances: –– If there is a strong electrical field around the Soundbar. –– If several Bluetooth devices are simultaneously paired with the Soundbar. –– If the Bluetooth device is turned off, not in place, or malfunctions. •• Electronic devices may cause radio interference. Devices that generate electromagnetic waves must be kept away from the Soundbar main unit - e.g., microwaves, wireless LAN devices, etc. •• The Soundbar supports SBC data (44.1kHz, 48kHz). •• Connect only to a Bluetooth device that supports the A2DP (AV) function. •• You cannot connect the Soundbar to a Bluetooth device that supports only the HF (Hands Free) function. •• Once you have paired the Soundbar to a Bluetooth device, selecting “[AV] Samsung Soundbar Nxxx” from the device’s scanned devices list will automatically change the Soundbar to “BT” mode. –– Available only if the Soundbar is listed among the Bluetooth device’s paired devices. (The Bluetooth device and the Soundbar must have been previously paired at least once.) •• The Soundbar will appear in the Bluetooth device’s searched devices list only when the Soundbar is displaying “BT READY”. •• The Soundbar cannot be paired to another Bluetooth device if already in Bluetooth mode and paired to a Bluetooth device. ENG - 20 Disconnecting the Bluetooth device from a Soundbar You can disconnect a Bluetooth device from the Soundbar. For instructions, see the Bluetooth device’s user manual. •• The Soundbar will be disconnected. •• When the Soundbar is disconnected from the Bluetooth device, the Soundbar will display “BT DISCONNECTED” on the front display. Disconnecting the Soundbar from the Bluetooth device Press the (Source) button on the top panel or on the remote control, and then change to any mode except “BT”. •• Disconnecting takes time because the Bluetooth device must receive a response from the Soundbar. (Disconnection time may differ, depending on the Bluetooth device) •• When the Soundbar is disconnected from the Bluetooth device, the Soundbar will display “BT DISCONNECTED” on the front display. NOTES •• In Bluetooth connection mode, the Bluetooth connection will be lost if the distance between the Soundbar and the Bluetooth device exceeds 10 meters. •• The Soundbar automatically turns off after 5 minutes in the Ready state. More About Bluetooth Bluetooth is a technology that enables Bluetooth-compliant devices to interconnect easily with each other using a short wireless connection. •• A Bluetooth device may cause noise or malfunction, depending on usage, if: –– A part of your body is in contact with the receiving/transmitting system of the Bluetooth device or the Soundbar. –– It is subject to electrical variation from obstructions caused by a wall, corner, or office partition. –– It is exposed to electrical interference from same frequency-band devices including medical equipment, microwave ovens, and wireless LANs. •• Pair the Soundbar with the Bluetooth device while they are close together. •• The further the distance between the Soundbar and Bluetooth device, the worse the quality is. If the distance exceeds the Bluetooth operational range, the connection is lost. •• In poor reception areas, the Bluetooth connection may not work properly. •• The Bluetooth connection only works when it is close to the unit. The connection will be automatically cut off if the Bluetooth device is out of range. Even within range, the sound quality may be degraded by obstacles such as walls or doors. •• This wireless device may cause electric interference during its operation. ENG - 21 Connecting via Wi-Fi (Wireless Network) •• Connect a single Soundbar to Wi-Fi to access a variety of music streaming services and Internet radio. Connect multiple Soundbars to Wi-Fi to use grouped playback or the stereo sound mode. •• To connect a Soundbar to a mobile device via a wireless network (Wi-Fi), the SmartThings app is required. Top of the Soundbar Mobile device The initial connection 1. Press the (Source) button on the top of the Soundbar or on the remote control to select “WIFI” mode. Top of the Soundbar WIFI 2. Install and launch the SmartThings app on your mobile device (e.g. smartphone or tablet). Android iOS ENG - 22 SmartThings app 3. Launch the app, and then follow the instructions on the screen to register (add) your Soundbar in the app. •• The automatic pop-up (the third illustration below) may not be available on some mobile devices. If this is the case, select and complete “Add device” from the app menu . Your Soundbar is now added to the app. Launch App Auto pop-up Add speakers NOTE •• To connect an additional SWA-9000S wireless rear speaker kit (not supplied), disconnect the Samsung wireless speakers from the Soundbar to disable the surround sound system. (If you connect the surround speakers without disconnecting the SWA-9000S speakers, sound is played via both the Samsung wireless speaker and the Surround speaker.) ENG - 23 07 CONNECTING AN AMAZON PRODUCT •• This feature may not be available in some countries. •• This service is provided by Amazon and can be terminated at any time. Samsung does not assume responsibility for service availability. Connect and use with an Amazon product (Amazon Echo) Use an Amazon Echo product to control your Soundbar and enjoy music services provided by Amazon Echo. NOTE •• Check if the Soundbar is connected to Wi-Fi. (Refer to “Connecting via Wi-Fi (Wireless Network)”) 1. In the SmartThings app, change your Soundbar’s name to one that can be recognized by your Amazon device. (Example: Samsung, Soundbar, Living Room, Family Room, Bedroom, Office, etc.) CAUTION •• Amazon devices may not recognize names that contain elements such as special characters. Select Edit Select speakers ENG - 24 Change name Save 2. In the Alexa app, search “Samsung Wireless Audio” in Skills, and then select “ENABLE”. •• Skip this step if you have Skills set up already. Amazon Alexa app Select Skills Search Enable 3. In the Alexa app, tap “Smart Home → Devices → Discover” to complete the connection. Amazon Alexa app Select Smart Home ENG - 25 Select Devices Discover device Use voice commands to control the Soundbar •• The Amazon Echo service you can use with your Soundbar is limited to music. Other services provided by Amazon Echo, such as news and weather, can only be accessed through your Amazon Echo product. Trigger + Command + Speaker name Use the Speaker name you changed in the SmartThings app. (Refer to “Connect and use with an Amazon product (Amazon Echo)”) Action Voice Command To search an audio device added to the SmartThings account connected to the "Alexa Discover devices" Amazon Alexa account * To use voice commands for the Soundbar named “Living room” Action Voice Command To set the volume level to 5 "Alexa Set the volume to 5 on Living room" To increase the volume level "Alexa Volume up on Living room" To mute the sound "Alexa Mute on Living room" To listen to a radio station named KISS FM "Alexa Play Kiss FM on Living room" To play the next song "Alexa Next song on Living room" To stop the audio "Alexa Stop on Living room" To turn the audio on "Alexa Turn on Living room" To turn the audio off "Alexa Turn off Living room" To change the input source "Alexa Switch to Bluetooth on Living room" ENG - 26 08 USING THE REMOTE CONTROL How to Use the Remote Control Turns the Soundbar on and off. Power PAIR Press to select a source connected to the Soundbar. •• BT PAIRING mode To turn on “BT PAIRING” mode, press and hold the (Source) button for more than 5 seconds. Source Press the (Mute) button to mute the sound. Press it again PAIR to unmute the sound. SOUND MODE WOOFER SOUND MODE Press to select the desired sound effect: SOUND MODE STANDARD, SURROUND, or SMART. Select the STANDARD mode if you want to enjoy SOUND MODE the original sound. PAIR PAIRmode •• SMART Automatically optimizes sound effects to suit SOUND the scene currently playing. VOL PAIR Mute SOUNDBAR MODE VOL VOL PAIR VOL WOOFER VOL WOOFER Press the PAIR button. “BT PAIRING” appears in the Soundbar’s display. You can connect the Soundbar to a new Bluetooth device in this mode by selecting the Soundbar in the Bluetooth device's search list. WOOFER PAIR Bluetooth SOUND MODE SOUND MODE WOOFER VOL ENG - 27 WOOFER Play / Pause (BT/Wi-Fi) Press the p button to pause a music file temporarily. Press the button again and the music file plays. •• Auto Power Down Function The unit turns off automatically in the following situations. –– D.IN / WIFI / BT Mode : If there is no audio signal for 5 minutes. –– HDMI 1 or HDMI 2 Mode : If there is no audio signal for 15 minutes. Press the indicated areas to select Up/Down/Left/Right. Up/Down/ PAIR Left/Right SOUND MODE VOL Press Up/Down/Left/Right on the button to select or set functions. •• Music Skip Press the Right button to select the next music file. Press the Left button to select the previous music file. WOOFER •• Anynet+ / Auto Power Link You can turn Anynet+ and Auto Power Link on or off. Anynet+ and Auto Power Link are turned on and turned off by the Right and Left buttons respectively. –– Anynet+ : If the Soundbar is connected to a Samsung TV through an HDMI cable, you can control your Soundbar with a Samsung TV remote control. Press and hold the Right button for 5 seconds to toggle Anynet+ ON and OFF. –– Auto Power Link : If the Soundbar is connected to your TV through a digital optical cable, the Soundbar can automatically turn on when you turn on your TV. Press and hold the Left button for 5 seconds to toggle Auto Power Link ON and OFF. –– Anynet+ / Auto Power Link are set to ON by default. •• ID SET Press and hold the Up button for 5 seconds to complete ID SET (when connecting to an accessary item). ENG - 28 You can select from TREBLE, BASS, SYNC, CENTER LEVEL, SIDE LEVEL, or FRONT TOP LEVEL. •• To control the volume of the treble or bass sound, select TREBLE or BASS in Sound Settings, and then adjust the volume between -6~+6 by using the Up/Down buttons. •• Press and hold the (Sound Control) button for about 5 seconds to adjust the sound for each frequency band. 150Hz, 300Hz, 600Hz, 1.2KHz, 2.5KHz, 5KHz, and 10KHz are selectable using the Left/Right buttons and each can be adjusted to a setting between -6 to +6 using the Up/Down buttons. •• To control the volume of the each speaker select CENTER LEVEL, SIDE LEVEL or FRONT TOP LEVEL in Sound Settings, and then adjust the volume between -6~+6 by using the Up/Down buttons. •• If the video on the TV and audio from the Soundbar are not synchronised, select SYNC in Sound Control, and then set the audio delay between 0~300 milliseconds by using the Up/Down buttons. •• SYNC is only supported for some functions. Sound Control PAIR SOUND MODE PAIR SO M UN OD D E SO U N VO L SO SO D BA R W OO W OO D BA R VO L U N VO L D BA R W OO OO D BA R U N O FE R FE R SOUND SOUNDMODE MODE U N FE R SO M UN OD D E SO M UN OD D E WOOFER WOOFER FE R VOL PAIR Push the button up or down to adjust the volume of the subwoofer to -12 or between -6 to +6. To set the subwoofer volume level to 0, press the button. R FE W OO BA R D N U SO VO L N D SO U U N VO L D BA R BA R W OO W OO FE FE R R WOOFER SO M UN OD D E SO M UN OD D E SO M UN OD D E WOOFER SO VOL VO L VOL VOL SO M UN OD D E Push the button up or down to adjust the volume. •• Mute Press the VOL button to mute the sound. Press it again to unmute the sound. ENG - 29 Adjusting the Soundbar volume with a TV remote control 4. If you want to return the Soundbar to the If you have a Samsung TV, you can adjust the Soundbar’s volume using the IR remote control that came with your Samsung TV. button for 5 seconds repeatedly until remote), push up and hold the WOOFER “SAMSUNG-TV REMOTE” appears in the display. (Default mode) 5 Sec FE W OO BA R D N U VO L SO control by a Samsung TV remote. If your TV is not SAMSUNG-TV REMOTE R SO M UN OD D E First use the TV menu to set the TV audio on your Samsung TV to external speakers, then use your Samsung remote to control the Soundbar’s volume. For more information, see the TV’s user manual. The default mode for this function is default mode (control by a Samsung TV –– Each time you push the WOOFER button up and hold it for 5 seconds, the mode switches in the following order: a Samsung TV, follow the directions below to change the settings of this function. 1. Turn Off the Soundbar. “SAMSUNG-TV REMOTE” (Default mode) → “OFF-TV REMOTE” → “ALL-TV REMOTE”. –– This function may not be available, depending on the remote control. BYE –– Manufacturers supporting this function: 2. If you do not want to use this function, push up and hold the WOOFER button on the “OFF-TV REMOTE” appears in the display. N D SO U VO L BA R W OO FE R SO M UN OD D E OFF-TV REMOTE 3. If you want to control the Soundbar with your TV’s remote, push up and hold the WOOFER button for 5 seconds repeatedly until “ALL‑TV REMOTE” appears in the display. Then, use your TV’s menu to select external speakers. ALL-TV REMOTE D N SO U VO L BA R W OO FE R SO M UN OD D E 5 Sec PANASONIC, TOSHIBA, GRUNDIG, Hisense, RCA remote repeatedly for 5 seconds until 5 Sec VIZIO, LG, Sony, Sharp, PHILIPS, ENG - 30 Using the Hidden Buttons (Buttons with more than one function) Hidden Button Reference page Remote Control Button Function WOOFER TV remote control On/Off (Standby) page 30 BT Pairing page 27 p (Play / Pause) Auto Power Down On/Off (AUX mode) page 28 BT Ready page 20 Left Auto Power Link ON/OFF page 28 Right Anynet+ ON/OFF page 28 Up ID SET page 28 7 Band EQ page 29 (Source) (Sound Control) Output specifications for the different sound effect modes Output Effect STANDARD SURROUND SMART With Subwoofer Only With Subwoofer & Surround Speaker With Subwoofer & Wireless Rear Speaker Kit 2.0 ch 2.1 ch 2.1 ch 2.1 ch 5.1 ch 5.1 ch 5.1 ch / 7.1 ch (DTS) 5.1 ch / 7.1 ch (DTS) 7.1 ch 5.1 ch 7.1 ch 7.1 ch 7.1.4 ch 5.1.2 ch 7.1.2 ch 7.1.2 ch 2.0 ch 5.1.2 ch 7.1.2 ch 7.1.2 ch 5.1 ch 5.1.2 ch 7.1.2 ch 7.1.2 ch 7.1 ch 5.1.2 ch 7.1.2 ch 7.1.2 ch 7.1.4 ch 5.1.2 ch 7.1.2 ch 7.1.2 ch 2.0 ch 2.1 ch 2.1 ch 2.1 ch 5.1 ch 5.1 ch 5.1 ch / 7.1 ch (DTS) 5.1 ch / 7.1 ch (DTS) 7.1 ch 5.1 ch 7.1 ch 7.1 ch 7.1.4 ch 5.1.2 ch 7.1.2 ch 7.1.2 ch Input •• If the input source is Dolby Atmos®, 7.1.2 channel is outputted. The sound effect is not available. •• The Samsung Wireless Rear Speaker Kit and the Surround Speakers can be purchased separately. To purchase a Kit or the Subwoofer, contact the vendor you purchased the Soundbar from. ENG - 31 09 INSTALLING THE WALL MOUNT Wallmount Components Installation Precautions Wall Mount Guide •• Install on a vertical wall only. •• Do not install in a place with high x2 x2 temperature or humidity. (M4 x L10) •• Verify that the wall is strong enough to Holder-Screw support the product’s weight. If not, reinforce the wall or choose another installation point. Screw x2 •• Purchase and use the fixing screws or anchors appropriate for the kind of wall you have (plaster board, iron board, wood, etc.). Bracket-Wall Mount If possible, fix the support screws into wall studs. •• Purchase wall mounting screws according to the type and thickness of the wall you want to 1. Place the Wall Mount Guide against the wall mount the Soundbar on. surface. •• The Wall Mount Guide must be level. –– Diameter: M5 –– Length: 35 mm or longer recommended. •• Connect cables from the unit to external •• If your TV is mounted on the wall, install the Soundbar at least 5 cm below the TV. devices before you install the Soundbar on the wall. •• Make sure the unit is turned off and unplugged before you install it. Otherwise, it 5 cm or more may cause an electric shock. ENG - 32 2. Align the Wall Mount Guide’s Centre Line 5. Push a screw (not supplied) through each with the centre of your TV (if you are Holder-Screw, and then screw each screw mounting the Soundbar below your TV), and firmly into a support screw hole. then fix the Wall Mount Guide to the wall using tape. •• If you are not mounting below a TV, place the Centre Line in the centre of the installation area. 6. Install the 2 Bracket-Wall Mounts in the correct orientation on the bottom of the Soundbar using 2 Screws. Centre Line 3. Push a pen tip or sharpened pencil tip through the centre of the A-TYPE images on each end of the Guide to mark the holes for the supporting screws, and then remove the Wall Mount Guide. •• When assembling, make sure the hanger part of the Bracket-Wall Mounts are located behind the rear of the Soundbar. Rear of Soundbar 4. Using an appropriately sized drill bit, drill a hole in the wall at each marking. •• If the markings do not correspond to the positions of studs, make sure you insert appropriate anchors or mollies into the holes before you insert the support screws. If you use anchors or mollies, make sure the holes you drill are large Right end of Soundbar enough for the anchors or mollies you use. ENG - 33 7. Install the Soundbar with the attached Bracket-Wall Mounts by hanging the Bracket-Wall Mounts on the Holder-Screws on the wall. 10 SOFTWARE UPDATE When the Soundbar is connected to the Internet, software updates automatically occur even when the Soundbar is turned off. •• To use the Auto Update function, the Soundbar must be connected to the Internet. The Wi-Fi connection to the Soundbar will be 8. Slide the Soundbar down as shown below so that the Bracket-Wall Mounts rest securely on the Holder-Screws. •• Insert the Holder-Screws into the wide (bottom) part of the Bracket-Wall Mounts, and then slide the Bracket-Wall Mounts down so that Bracket-Wall Mounts rest securely on the Holder-Screws. ENG - 34 terminated if the Soundbar’s power cord is disconnected or the power is cut off. If the power is cut off, when the power comes back on or you reconnect the power cord, turn on the Soundbar, and then reconnect it to the Internet. 11 TROUBLESHOOTING Before seeking assistance, check the following. The unit will not turn on. Is the power cord plugged into the outlet? ;; Connect the power plug to the outlet. The red LED on the subwoofer blinks and the subwoofer is not producing sound. This issue can occur if the subwoofer is not connected to the Soundbar main unit. A function does not work when the button is pressed. ;; Try to connect your subwoofer again. Is there static electricity in the air? The subwoofer drones and vibrates noticeably. ;; Disconnect the power plug and connect it again. (See page 6.) Try to adjust the vibration of your subwoofer. Sound dropouts occur in BT mode. ;; Push the WOOFER button on your remote control up or down to adjust the subwoofer ;; See the Bluetooth connection sections on pages 12 and 19. Sound is not produced. Is the Mute function on? ;; Press the volume. (to -12, or between -6 ~ +6). Cannot connect to the TV. If connected via a wired network ;; Check if the cable is connected correctly. (Check the port name to make sure that (Mute) button to cancel the the cable is connected to the correct port.) mute function. (See the corresponding page regarding Is the volume set to minimum? ;; Adjust the Volume. The remote control does not work. each connection method.) ;; Press the control to check if the mode is correct. Are the batteries drained? ;; Replace with new batteries. Is the distance between the remote control (Source) button on the top panel of the Soundbar or on the remote If connected via a wireless network ;; Connected via Bluetooth 1. Switch the Soundbar to “BT PAIRING” and Soundbar main unit too far? mode, and then use the TV to search ;; Move the remote control closer to the again. (See page 12 for details.) Soundbar main unit. ENG - 35 12 LICENCE ;; Connected via Wi-Fi 1. Check if the TV is a compatible model. •• Only Samsung Smart TVs released after 2013 are supported. 2. Check if the TV is connected to Wi-Fi. •• If the TV is not connected to Wi-Fi, use the network menu on the TV to Manufactured under license from Dolby Laboratories. Dolby, Dolby Atmos, Dolby Audio, establish a connection. (See the TV Dolby Digital Plus, Pro Logic, and the double-D user manual.) symbol are trademarks of Dolby Laboratories. 3. Check if the Soundbar is connected to Wi-Fi. •• When the Soundbar is connected, you can find it in the list of speakers on For DTS patents, see http://patents.dts.com. your mobile device when you run the Manufactured under license from DTS SmartThings app. See page 22 for details. 4. Check for a DFS channel. •• If your wireless router (Wi-Fi) is using a DFS channel, you cannot establish a Wi-Fi connection between the TV and Soundbar. Contact your Internet service provider for details. Licensing Limited. DTS, the Symbol, & DTS and the Symbol together, DTS:X, and the DTS:X logo are registered trademarks and/or trademarks of DTS, Inc. in the United States and/or other countries. © DTS, Inc. All Rights Reserved. The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. •• The Spotify Software is subject to third party licences found here : www.spotify.com/connect/third-partylicenses. •• For more information about Spotify Connect, please visit www.spotify.com/ connect ENG - 36 13 OPEN SOURCE LICENCE NOTICE For further information on Open Sources used in this product, please visit the website: http://opensource.samsung.com 14 IMPORTANT NOTES ABOUT SERVICE Figures and illustrations in this User Manual are provided for reference only and may differ from actual product appearance. ENG - 37 15 SPECIFICATIONS AND GUIDE Specifications Model Name HW-N850 Weight 8.8 kg Dimensions (W x H x D) 1226.0 x 83.0 x 136.0 mm Operating Temperature Range +5°C to +35°C Operating Humidity Range 10 % ~ 75 % AMPLIFIER Rated Output power 18W x 10 + 10W x 3, 4ohm LPCM 2ch, Dolby Audio™ Supported play formats (supporting Dolby® Digital), DTS Subwoofer Name PS-WN80 Weight 9.6 kg Dimensions (W x H x D) 203.5 x 400.0 x 415.5 mm AMPLIFIER Rated Output power 162W NOTES •• Samsung Electronics Co., Ltd reserves the right to change the specifications without notice. •• Weight and dimensions are approximate. •• For India Only “This product is RoHS compliant” Precaution : The Soundbar will restart automatically if you turn on/turn off Wi-Fi. Wi-Fi Port deactivation method Bluetooth Port deactivation method Press the ID SET button on the bottom panel of the Soundbar for 30 seconds to turn Wi-Fi On / Off. Press the NETWORK button on the bottom panel of the Soundbar for 30 seconds to turn Bluetooth On / Off. ENG - 38 © 2018 Samsung Electronics Co., Ltd. All rights reserved. Contact SAMSUNG WORLD WIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care Centre. Area Contact Centre Web Site ` Asia Pacific CHINA 400-810-5858 www.samsung.com/cn/support HONG KONG 3698 4698 www.samsung.com/hk/support (Chinese) www.samsung.com/hk_en/support (English) MACAU 0800 333 www.samsung.com/support SINGAPORE 1800 7267864 | 1800-SAMSUNG www.samsung.com/sg/support AUSTRALIA 1300 362 603 www.samsung.com/au/support NEW ZEALAND 0800 726 786 (All Product) 0800 6 726 786 www.samsung.com/nz/support VIETNAM 1800 588 889 www.samsung.com/vn/support THAILAND 0-2689-3232 1800-29-3232 (Toll free) www.samsung.com/th/support MYANMAR +95-1-2399-888 www.samsung.com/mm/support CAMBODIA +855-23-993232 1800-20-3232 (Toll free) www.samsung.com/th/support LAOS +856-214-17333 MALAYSIA 1800-88-9999 +603-7713 7420 (Overseas contact) www.samsung.com/my/support INDONESIA 021-5699-7777 0800-112-8888 (All Product, Toll Free) www.samsung.com/id/support PHILIPPINES 1-800-10-726-7864 [ PLDT Toll Free ] 1-800-8-726-7864 [ Globe Landline and Mobile ] 02-422-2111 [ Standard Landline ] www.samsung.com/ph/support TAIWAN 0800-329-999 www.samsung.com/tw/support INDIA 1800 40 SAMSUNG (1800 40 7267864) (Toll-Free) NEPAL 16600172667 (Toll Free for NTC Only) 9801572667 BANGLADESH 09612300300 08000300300 (Toll free) SRI LANKA +9411SAMSUNG (+94117267864) +94117540540 +94115900000 www.samsung.com/in/support
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Key Features
- 5.1.2 channels
- Wi-Fi Bluetooth
- Black