Samsung | SP-43T8HL | Samsung SP-43T8HL Quick start guide

BP68-00303A(J60A_Asia_ENG)
4/2/04
12:14 AM
Page 6
Control Panels (depending on the model)
➢
ENG
The actual configuration on your TV may be different, depending on
your model.
SP43T7
SP43T8
SP54T8
SP43W6
SP42Q2
(a)
(b)
(c)
(d)
(e)
➢
Input Source Selection
Menu Display
Channel Selection
Volume Adjustment
Power On/Off
( f ) Standby & Timer Indicator
( g ) Remote Control Sensor
( h ) Accessing to the Selected Option
on the Menu System
( i ) Picture On/Off
Using the Buttons on the Panel
If the remote control no longer works or you have lost it, you can use controls on the panel of the TV to:
◆ Switch on the TV when it is in Standby mode and select channels
(
CH
or Picture On/Off)
◆ Access the menu ( MENU )
◆ Adjust the volume ( - VOL + )
◆ Switch among Video input modes (SOURCE ) and access to the selected option on the menu
system ( )
1
BP68-00303A(J60A_Asia_ENG)
4/2/04
12:14 AM
Page 7
Connection Panels (depending on the model)
➢
The actual configuration on your TV may be different, depending on
your model.
ENG
Side of the TV
( a ) Video Input
( b ) Audio Input
( c ) S-Video Input
Rear of the TV
( a ) ANT IN VHF/UHF (75Ω)
d
( b ) AV INPUT
(VIDEO/L-AUDIO-R)-1, 2
( c ) AV OUTPUT
(VIDEO / L-AUDIO-R)
( d ) COMPONENT
VIDEO/AUDIO INPUT
c
a
:
➢
☛
b
For further details about connection, refer to pages 7~10.
Whenever you connect an audio or video system to your television, ensure that all elements are
switched off. Refer to the documentation supplied with your equipment for detailed connection
instructions and associated safety precautions.
2
BP68-00303A(J60A_Asia_ENG)
4/2/04
12:14 AM
Page 8
Using a Display Deck (depending on the model)
ENG
You can display a VCR or DVD Player, etc. by using the display
deck.
SP43W6
SP54T8
1
Hold the center of the door and lift it up in the direction of arrow.
2
After placing a component you have in the display deck, hold the
center of the door and pull it down.
➢
SP54T8
You should display only the component that is within
126mm high. When displaying a component in the
display deck, please space it out 30mm from the front,
20mm from either end.
Inserting the Batteries in the Remote Control
You must insert or replace the batteries in the remote control when
you:
◆ Purchase the television
◆ Find that the remote control is no longer operating
correctly
3
1
Remove the cover on the rear of the remote control by pressing
the symbol ( ) downwards and then pulling firmly to remove it.
2
Insert two R03, UM4, “AAA” 1.5V or equivalent batteries taking
care to respect the polarities:
◆ + on the battery against + on the remote control
◆ - on the battery against - on the remote control
3
Replace the cover by aligning it with the base of the remote
control and pressing it back into place.
BP68-00303A(J60A_Asia_ENG)
4/2/04
12:14 AM
Page 9
Infrared Remote Control
ENG
TELEVISION STANDBY
PICTURE SIZE/
TELETEXT SIZE SELECTION
TUNER/CABLE NETWORK
SELECTION
MAKE THE REMOTE CONTROL WORKS
FOR TV, STB, VCR, CABLE, DVD
PLAYER
DIRECT CHANNEL SELECTION
ONE OR TWO-DIGIT CHANNEL
SELECTION/
TELETEXT STORE
VOLUME INCREASE
TEMPORARY SOUND SWITCH-OFF
VOLUME DECREASE
TELETEXT DISPLAY/
MIX BOTH TELETEXT INFORMATION
AND THE NORMAL BROADCAST
SWITCH REPEATEDLY BETWEEN THE
LAST TWO CHANNELS DISPLAYED
NEXT CHANNEL/
TELETEXT NEXT PAGE
EXTERNAL INPUT SELECTION/
TELETEXT MODE (LIST/FLOF)
SELECTION
PREVIOUS CHANNEL/
TELETEXT PREVIOUS PAGE
INFORMATION DISPLAY/
TELETEXT REVEAL
EXIT FROM ANY DISPLAY
MENU DISPLAY/
TELETEXT INDEX
CONTROL THE CURSOR
IN THE ON-SCREEN MENU
SOUND EFFECT SELECTIOND
SURROUND ON/OFF DIRECTLY
SELF FOCUS
PICTURE FREEZE
TELETEXT SUB-PAGE
REMOTE CONTROL SETUP
CONFIRM YOUR CHOICE
(STORE OR ENTER)
PICTURE EFFECT SELECTION
SOUND MODE SELECTION
FASTEXT TOPIC SELECTION
AUTOMATIC SWITCH-OFF
VCR/DVD FUNCTIONS;
- REWIND (
)
- STOP ( )
- PLAY/PAUSE (
)
- FAST FORWARD (
)
TELETEXT CANCEL
IF YOUR REMOTE CONTROL IS
NOT FUNCTIONING PROPERLY,
TAKE OUT THE BATTERIES AND
PRESS THE RESET BUTTON FOR
ABOUT 2~3 SECONDS. RE-INSERT
THE BATTERIES AND TRY USING
THE REMOTE CONTROL AGAIN.
➢
TELETEXT PAGE HOLD
The performance of the remote control may be affected by bright light.
4
BP68-00303A(J60A_Asia_ENG)
4/2/04
12:14 AM
Page 10
Connecting to an Aerial or Cable Television Network
ENG
To view television channels correctly, a signal must be received by
the set from one of the following sources:
◆ An outdoor aerial
◆ A cable television network
◆ A satellite network
Rear of the TV
or
Cable Television
Network
5
1
In the first three cases, connect the aerial or network input cable to
the 75Ω coaxial socket on the rear of the television.
2
If you are using an indoor aerial, you may need to turn it when
tuning your television until you obtain a picture that is both sharp
and clear.
For further details, refer to the user manual :
◆ “Storing Channels Automatically” on page 20
◆ “Storing Channels Manually” on page 22.
BP68-00303A(J60A_Asia_ENG)
4/2/04
12:14 AM
Page 11
Connecting a Satellite Receiver or Decoder
ENG
In order to watch television programmes broadcast via a satellite
network, you must connect a satellite receiver to the rear of TV.
Also, in order to descramble a coded transmission signal, you must
connect a decoder to the rear of TV.
Rear of the TV
Using a Coaxial cable
Connect a coaxial cable to the:
◆ Receiver (or Decoder) output socket.
◆ Television aerial input socket.
➢
If you wish to connect both a satellite receiver (or decoder)
and a VCR, you should connect the:
◆ Receiver (or Decoder) to the VCR
◆ VCR to the television
Otherwise, connect the receiver (or decoder) directly to the
television.
Satellite receiver/
Decoder
6
BP68-00303A(J60A_Asia_ENG)
4/2/04
12:15 AM
Page 49
Connecting to the External Devices
ENG
Rear of the TV
(Input/Output)
VCR
②
Decoder /
Video game device
③
Video disc player
①
Satellite receiver
➃
① This end can be fitted with:
◆ Three RCA connectors (VIDEO + AUDIO-L and R)
② If you have a second VCR and wish to copy cassettes tape, connect the source VCR to “IN 1” and the
target VCR to “OUT” so that you can redirect the signal from source VCR to target VCR.
③ If you have a decoder, connect the decoder to the VCR and the VCR to the television.
➃ “OUT” is used for displaying the current picture to an external device. When you wish to record the
current picture, connect the VCR to “OUT”.
Side of the TV
(Input)
(depending on the model)
Camcorder
Video disc player
Video game device
☛
Whenever you connect an audio or video system to your
television, ensure that all elements are switched off.
Refer to the documentation supplied with your equipment
for detailed connection instructions and associated safety
precautions.
7
BP68-00303A(J60A_Asia_ENG)
4/2/04
12:15 AM
Page 50
Connecting to the Audio Outputs
ENG
➢
The AUDIO-L and R connectors are used for equipment, such as an audio system or external amplifier
(to take full advantage of the Surround sound effect).
Rear of the TV
Audio System/
External Amplifier
8
BP68-00303A(J60A_Asia_ENG)
4/2/04
12:15 AM
Page 51
Connecting to the S-Video Input
ENG
➢
The S-VIDEO (or S-VIDEO INPUT) and RCA (AUDIO3-L and R) connectors are used for
equipment with an S-Video output, such as a camcorder or VCR.
Side of the TV
(depending on the model)
①
Camcorder
and
VCR
①
and
① To play pictures and sound, both the S-VIDEO (or S-VIDEO INPUT) and RCA connectors must be used.
9
BP68-00303A(J60A_Asia_ENG)
4/2/04
12:15 AM
Page 52
Connecting to the Component Input
ENG
Rear of the TV
①
②
➢
DVD
DTV receiver
The COMPONENT IN connectors are used for equipment with a DVD or DTV receiver output.
(480i, 480p, 576i,576p, 1080i)
10
Download PDF

advertising