Samsung | HT-C6950W | Samsung 3D домашний кинотеатр с Blu-ray HT-C6950W Operating instrustions

HT-C6950W
7.1CH Blu-ray
Home Cinema System
user manual
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
www.samsung.com/register
HT-C6950W_CIS_ENG_0407.indd 1
2010-04-08
6:25:30
Safety Information
Safety Warnings
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER(OR BACK).
NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This symbol indicates “dangerous
CAUTION : TO PREVENT ELECTRIC
voltage” inside the product that presents SHOCK, MATCH WIDE BLADE OF PLUG
a risk of electric shock or personal injury. TO WIDE SLOT, FULLY INSERT.
WARNING
• To reduce the risk of fire or electric shock, do
not expose this appliance to rain or moisture.
CAUTION
• Apparatus shall not be exposed to dripping or splashing
and no objects filled with liquids, such as vases, shall be
placed on the apparatus.
• The Mains plug is used as a disconnect device and shall
stay readily operable at any time.
• This apparatus shall always be connected to a AC outlet
with a protective grounding connection.
• To disconnect the apparatus from the mains, the plug
must be pulled out from the mains socket, therefore the
mains plug shall be readily operable.
2
CLASS 1
KLASSE 1
LUOKAN 1
KLASS 1
PRODUCTO
This symbol indicates important
instructions accompanying the
product.
LASER PRODUCT
LASER PRODUKT
LASER LAITE
LASER APPARAT
LÁSER CLASE 1
CLASS 1 LASER PRODUCT
This Compact Disc player is classified as a
CLASS 1 LASER product.
Use of controls, adjustments or performance of
procedures other than those specified herein
may result in hazardous radiation exposure.
CAUTION
• INVISIBLE LASER RADIATION WHEN OPEN AND
INTERLOCKS DEFEATED, AVOID EXPOSURE TO BEAM.
English
HT-C6950W_CIS_ENG_0407.indd 2
2010-04-08
6:25:50
Precautions
• Ensure that the AC power supply in your house complies with the identification sticker located on the back of
your product.
• Install your product horizontally, on a suitable base (furniture), with enough space around it for ventilation
(7.5~10cm).
• Do not place the product on amplifiers or other equipment which may become hot.
Make sure the ventilation slots are not covered.
• Do not stack anything on top of the product.
• Before moving the product, ensure the Disc Insert Hole is empty.
• In order to disconnect the product completely from the power supply, remove the main plug from the wall outlet,
especially when left unused for a long period of time.
• During thunderstorms, disconnect the AC main plug from the wall outlet. Voltage peaks due to lightning could
damage the product.
• Do not expose the product to direct sunlight or other heat sources. This could lead to overheating and
malfunction of the product.
• Protect the product from moisture, and excess heat or equipment creating strong magnetic or electric fields (i.e.
speakers.).
• Disconnect the power cable from the AC supply if the product malfunctions.
• Your product is not intended for industrial use. Use of this product is for personal use only.
• Condensation may occur if your product or disc has been stored in cold temperatures. If transporting the
product during the winter, wait approximately 2 hours until the product has reached room temperature before
using.
• The batteries used with this product contain chemicals that are harmful to the environment.
Do not dispose of batteries in the general household trash.
Viewing TV using 3D function
Important safety Information. Read the following warnings before you or your child use the 3D function.
• The pregnant, elderly and epileptic and those suffering from a weak heart or serious carsickness are advised to
avoid watching 3D pictures.
• We don’t recommend 3D pictures to those who are in bad physical condition, who are sleep-deprived or who
drank liquor. Some 3D pictures may startle viewers.
• Do not place a sharp-edged or easily breaking object around you when playing a 3D video. If you feel and
respond your body to the 3D video like it’s real, you can break the object around you or be physically damaged.
• Photosensitive Seizure Warning and Other Health Risks
- Some viewers may experience an epileptic seizure or stroke when exposed to certain flashing
images or lights contained in certain television pictures or video games. If you or any of your
relatives has a history of epilepsy or strokes, please consult with a medical specialist before using
the 3D function.
- If you have any one of the following symptoms or conditions while watching 3D pictures, stop
watching immediately and rest: dizziness, eye or facial instability, involuntary movement, cramps,
clouded consciousness, mental disorder, disorientation or nausea. (If the symptom persists, please
consult a medical specialist.)
- In particular, children or teenagers need parent care and guard when they watching the 3D video.
- Do not watch 3D pictures when you feel incoherent, sleepy, tired or sick. Avoid watching 3D
pictures for long hours.
English
HT-C6950W_CIS_ENG_0415.indd 3
3
2010-04-15
6:02:02
Safety Information
Cautions on Handling and Storing Discs
Small scratches on the disc may reduce sound
and picture quality or cause skipping.
Be especially careful not to scratch discs when
handling them.
Holding discs
• Do not touch the playback side of the disc.
• Hold the disc by the edges so that fingerprints will not
get on the surface.
• Do not stick paper or tape on the
disc.
Disc Storage
• Do not keep in direct sunlight
• Keep in a cool ventilated area
• Keep in a clean Protection jacket.
Store vertically.
✎ NOTE
 Do not allow the discs to become contaminated with
dirt.
 Do not load cracked or scratched discs.
Handling and Storing Discs
If you get fingerprints or dirt on the disc, clean it with a
mild detergent diluted in water and wipe with a soft cloth.
Licence
• This product incorporates copyright protection technology that is
protected by U.S. patents and other intellectual property rights. Use of
this copyright protection technology must be authorized by Rovi
Corporation, and is intended for home and other limited viewing uses
only unless otherwise authorized by Rovi Corporation. Reverse
engineering or disassembly is prohibited.
• ABOUT DIVX VIDEO: DivX® is a digital video format
created by DivX,Inc. This is an official DivX Certified
device that plays DivX video. Visit www. divx.com for
more information and software tools to convert your
files into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be
registered in order to play DivX Video-on-Demand (VOD) content. To
generate the registration code, locate the DivX VOD section in the
device setup menu. Go to vod.divx.com with this code to complete the
registration process and learn more about DivX VOD.
DivX Certified to play DivX video up to HD 1080p, including premium
content.
• Manufactured under licence from Dolby Laboratories. Dolby,
Pro Logic and the double-D symbol are trademarks of Dolby
Laboratories.
• < Open Source Licence Notice >
In the case of using open source software, Open Source
Licences are available on the product menu.
• "Blu-ray 3D" and "Blu-ray 3D"logo are trademarks of Blu-ray
Disc Association.
Copyright
© 2010 Samsung Electronics Co., Ltd. All rights
reserved.
• When cleaning, wipe gently from the inside to
the outside of the disc
✎ NOTE
 Condensation may form if warm air comes into
contact with cold parts inside the product. When
condensation forms inside the product, it may not
operate correctly. If this occurs, remove the disc
and let the product stand for 1 or 2 hours with the
power on.
4
English
HT-C6950W_CIS_ENG_0407.indd 4
2010-04-08
6:25:50
Contents
Safety Warnings
Precautions
Cautions on Handling and Storing Discs
Licence
Copyright
GETTING STARTED
7
8
12
13
13
14
15
Icons that will be used in manual
Disc Types and Characteristics
Accessories
Description
Front Panel
Rear Panel
Remote control
CONNECTIONS
17
22
24
25
26
27
Connecting the Speakers
Connecting External Devices/your TV via HDMI
Connecting the Video Out to your TV
Connecting Audio from External Components
Connecting to the Network
Connecting the FM Antenna
SETUP
28
29
30
30
31
31
31
33
33
33
33
33
34
34
35
35
36
37
37
37
37
37
37
37
38
38
38
39
39
40
40
40
41
41
41
Before Starting (Initial settings)
Setting the Menu
Display
3D
TV Aspect
BD Wise
Resolution
HDMI Format
Movie Frame (24 Fs)
Progressive Mode
Still Mode
HDMI Deep Color
Audio
Speaker Setting
Musical Auto Calibration
HDMI Audio
Digital Output
Dynamic Range Control
AV Sync
System
Initial Settings
Internet@TV Screen Size
Anynet+(HDMI-CEC)
BD Data Management
Clock
DivX(R) Registration
DivX(R) Deactivation
Network Setup
Network Settings
Network Status
BD-LIVE Internet Connection
Language
Security
Parental Rating
Change Password
2
7
17
28
ENGLISH
2
3
4
4
4
SAFETY INFORMATION
English
HT-C6950W_CIS_ENG_0407.indd 5
5
2010-04-08
6:25:50
Contents
SETUP
41
41
41
41
41
42
42
42
General
Background
Front Display
Power On/Off Sound
Light Effect
Support
Software Upgrade
Contact Samsung
BASIC FUNCTIONS
43
43
44
45
45
46
48
50
51
52
53
Playing a Disc
Using the Disc menu / Title menu / Popup menu
Using the Search and Skip Functions
Slow Motion Play/Step Motion Play
Repeat Playback
Using the TOOLS button
Listening to Music
Sound Mode
Playing back a Picture
Playing back a USB Storage
Listening to Radio
NETWORK SERVICES
54
58
58
58
Using Internet@TV
BD-LIVE™
Software Upgrade Notification
Using the AllShare Function
OTHER INFORMATION
60
63
Troubleshooting
Specifications
41
43
54
60
• Figures and illustrations in this User Manual are provided for reference only and may differ from actual product appearance.
6
English
HT-C6950W_CIS_ENG_0407.indd 6
2010-04-08
6:25:51
01
Getting Started
Getting Started
Icons that will be used in manual
Make sure to check the following terms before reading the user manual.
Term
Logo
Icon
h
z
Z
BD-ROM
BD-RE/-R
DVD-VIDEO
Definition
This involves a function available on a BD-ROM.
This involves a function available on a BD-RE/-R disc recorded in the
BD-RE format.
This involves a function available on a DVD-VIDEO.
DVD-RW(V)
DVD-R
y
DVD+RW
This involves a function available on recorded DVD+RW or DVD-RW(V)/
DVD-R/+R discs that have been recorded and finalsed.
DVD+R
Audio CD
MP3
WMA
-
JPEG
-
DivX
MKV
MP4
DivX
USB storage
device
-
CAUTION
-
NOTE
-
Shortcut Key
-
o
w
G
x
F
!
✎
This involves a function available on an audio CD-RW/-R (CD-DA format).
This involves a function available in a CD-RW/-R, DVD-RW/-R disc or a
USB storage media containing MP3 or WMA contents.
This involves a function available in a CD-RW/-R, DVD-RW/-R disc or a
USB storage media containing JPEG contents.
This involves a function available in a CD-RW/-R, DVD-RW/-R disc or a
USB storage media containing DivX contents.
This involves a function available on a USB storage device.
This involves a situation where a function does not operate or settings may
be cancelled.
This involves tips or instructions on the page that help each function
operate.
This function provides direct and easy access pressing the button on
the remote control.
• This product is compatible with the PAL colour system only.
• NTSC discs will not play.
English
HT-C6950W_CIS_ENG_0407.indd 7
7
2010-04-08
6:25:51
Getting Started
Disc Types and Characteristics
Logos of Discs that can be played
Blu-ray Disc Compatibility
Blu-ray is a new and evolving format. Accordingly, disc
compatibility issues are possible. Not all discs are
compatible and not every disc will play back. For
additional information, refer to the Disc Types and
Characteristics section of this Manual. If you encounter
compatibility problems, please contact the SAMSUNG
customer care centre.
Blu-ray Disc
3D Blu-ray Disc
Dolby Digital Plus
PAL broadcast system in
U.K, France, Germany, etc.
Dolby TrueHD
DTS-HD High Resolution
Audio
Java
DTS-HD Master Audio |
Essential
✎ NOTE
 Playback may not work for some types of discs, or
when specific operations, such as angle change
and aspect ratio adjustment, are being performed.
Information about the discs is written in detail on
the box. Please refer to this if necessary.
 Do not allow the disc to become dirty or scratched.
Fingerprints, dirt, dust, scratches or deposits of
cigarette smoke on the recording surface may
make it impossible to use the disc for playback.
 When a BD-Java title is played, loading may take
longer than a normal title, or some functions may
perform slowly.
Discs that cannot be played
•
•
•
•
•
•
HD DVD Disc
DVD-RAM
3.9 GB DVD-R Disc for Authoring.
DVD-RW(VR mode)
Super Audio CD(except CD layer)
DVD-ROM/PD/MV-Disc, etc CVD/CD-ROM/
CDV/CD-G/CD-I/LD
• CDGs play audio only, not graphics.
✎ NOTE
BD-LIVE
 Some commercial discs and DVD discs purchased
outside your region may not be playable with this
product. When these discs are played, “Cannot read
this disc. Please check the regional code of the
disc.” will be displayed.
 If a DVD-R/-RW disc has not been recorded
properly in DVD video format, it will not be playable.
8
English
HT-C6950W_CIS_ENG_0407.indd 8
2010-04-08
6:25:51
01
Disc Types
Both the product and the discs are coded by
region. These regional codes must match in
order to play the disc. If the codes do not match,
the disc will not play.
BD-ROM
Disc Type
Blu-ray
DVD-VIDEO
Region
Code
Area
A
North America, Central America,
South America, Korea, Japan,
Taiwan, Hong Kong and South
East Asia.
B
Europe, Greenland, French
territories, Middle East, Africa,
Australia and New Zealand.
C
India, China, Russia, Central and
South Asia.
1
The U.S., U.S. territories and
Canada
2
Europe, Japan, the Middle East,
Egypt, South Africa, Greenland
3
Taiwan, Korea, the Philippines,
Indonesia, Hong Kong
4
Mexico, South America, Central
America, Australia, New Zealand,
Pacific Islands, Caribbean
5
Russia, Eastern Europe, India,
most of Africa, North Korea,
Mongolia
6
China
Blu-ray Disc Read Only Memory. A BD-ROM disc
contains pre-recorded data. Although a BD-ROM
may contain any form of data, most BD-ROM discs
will contain movies in High Definition format, for
playback on the product. This product can play
back pre-recorded commercial BD-ROM discs.
Getting Started
Region code
BD-RE/BD-R
Blu-ray Disc Rewritable/Blu-ray Disc Recordable.
BD-RE/BD-R is the ideal format for making
backups, or recording personal video.
DVD-VIDEO
• A digital versatile disc (DVD) can contain up to 135minutes of images, 8 audio languages and 32 subtitle
languages. It is equipped with MPEG-2 picture
compression and Dolby Digital surround, allowing you
to enjoy vivid and clear quality images.
• When switching from the first layer to the second
layer of a dual-layered DVD Video disc, there may
be momentary distortion in the image and sound.
This is not a malfunction of the product.
• Once a DVD-RW/-R recorded in Video Mode is
finalsed, it becomes DVD-Video. Pre-recorded
(pre-stamped) commercial DVDs with movies are
also referred to as DVD-Videos. This product can
play back pre-recorded commercial DVD discs
(DVD-Video discs) with movies.
DVD-R/-RW
• Once a DVD-R/-RW recorded in Video Mode is
finalsed, it becomes DVD-Video. Ability to play
back may depend on recording conditions.
• This product can play back DVD-R disc recorded
and finalsed with a Samsung DVD video recorder.
• Playback can be perfomed with DVD-RW discs in
the Video Mode and finalsed only.
DVD+RW
• This product can play back a DVD+RW disc
recorded with a DVD Video recorder. Ability to
play back may depend on recording conditions.
DVD+R
• This product can play back a DVD+R disc recorded
and finalsed with a DVD Video recorder. Ability to
play back may depend on recording conditions.
English
HT-C6950W_CIS_ENG_0407.indd 9
9
2010-04-08
6:25:52
Getting Started
Audio CD
DivX(Digital Video Express)
• An audio disc on which 44.1kHz PCM Audio is
recorded.
• This product can play back CD-DA format audio
CD-R and CD-RW discs.
• The product may not be able to play some CD-R or
CD-RW discs due to the condition of the recording.
DivX is a video file format developed by Microsoft and is
based on MPEG4 compression technology to provide
audio and video data over the Internet in real-time.
MPEG4 is used for video encoding and MP3 for audio
encoding so that the users can watch a movie at near
DVD-quality video and audio.
CD-R/-RW
Supported Formats(DivX)
• Use a 700MB(80 minutes) CD-R/-RW disc.
If possible, do not use a 800MB(90 minutes) or above
disc, as the disc may not play back.
• If the CD-R/-RW disc was not recorded as a closed
session, you may experience delays when playing
back the beginning of the disc or all recorded files
may not play.
• Some CD-R/-RW discs may not be playable with this
product, depending on the device which was used to
burn them. For contents recorded on CD-R/-RW
media from CDs for your personal use, playability
may vary depending on contents and discs.
This product only supports the following media formats.
If both video and audio formats are not supported, the
user may experience problems such as broken images
or no sound.
Supported Video Formats
Format
AVI
Supported Versions
DivX3.11~DivX5.1, XviD
Supported Audio Formats
Format
Using MP3 disc
MP3
80~384kbps
44.1khz
AC3
128~384kbps
44.1/48khz
DTS
1.5Mbps
44.1khz
• CD-R/-RW, DVD-RW/-R recorded with UDF,
ISO9660 or JOLIET format can be played back.
• Only MP3 files with the “.mp3” or “.MP3” extension
can be played.
• Playable bit rate range is from 56 Kbps to 320 Kbps.
• Playable sample-rate is 32KHz to 48KHz.
• The product can handle a maximum of 1500 files and
folders under a parent folder. For MP3 files recorded with
a VBR(Variable Bit Rates), the sound may cut in and out.
Using JPEG disc
• CD-R/-RW, DVD-RW/-R recorded with UDF,
ISO9660 or JOLIET format can be played back.
• Only JPEG files with the ".jpg", ".JPG", ".jpeg" or
"JPEG" extension can be displayed.
• Progressive JPEG is supported.
DVD-RW/-R (V)
• This is a format that is used for recording data on a
DVD-RW or DVD-R disc. The disc can be played by
this product once it has been finalsed.
• If a disc that has been recorded in Video Mode by a
different maker’s recorder but has not been finalsed,
it cannot be played by this product.
10
Bit Rate
Sampling
Frequency
Disc Format
• DivX files, including audio and video files, created
in the DTS format can only support up to 6Mbps.
• Aspect Ratio : Although the default DivX resolution
is 640x480 pixels (4:3), this product supports up
to 800x600 pixels (16:9). TV screen resolutions
higher than 800 will not be supported.
• When you play a disc whose sampling frequency is
higher than 48khz or 320kbps, you may experience
shaking on the screen during playback.
• Qpel and gmc is not supported.
MKV, MP4
• CD-R/-RW, DVD-R/-RW, USB, PC streaming
• Video Files with the following extensions can be
played. : .avi, .divx, .mkv, .mp4, .AVI, .DIVX,
.MKV, .MP4
✎ NOTE
 Some DivX, MKV and MP4 format discs may
not play, depending on the video resolution and
frame rate condition.
English
HT-C6950W_CIS_ENG_0407.indd 10
2010-04-08
6:25:52
01
Video File Support
File Extension
Container
*.avi
Video Codec
Audio Codec
Resolution
Divx 3.11/4.x/5.1/6.0
MP3
AC3
DTS
WMA
PCM
1920x1080
XviD
AVI
MP4v3
H.264 BP/MP/HP
1920x1080
1920x1080
1920x1080
1920x1080
VC-1 AP
*.mkv
*.wmv
DivX 5.1/6.0
MKV
XviD
WMV (wmv9)
*.mp4
MP4
*.mpg
*.mpeg
PS
Getting Started
Supported File Formats
MP3
AC3
DTS
1920x1080
1920x1080
H.264 BP/MP/HP
1920x1080
VC-1 AP
1920x1080
WMA
VC-1 SM
MP4 (mp4v)
H.264 BP/MP/HP
MPEG1
MPEG2
H.264 BP/MP/HP
1920x1080
1920x1080
AAC
1920x1080
1920x1080
MP1, 2
AC3
DTS
1920x1080
1920x1080
Music File Support
File Extension
Container
Audio Codec
Support Range
*.mp3
MP3
MP3
-
WMA
Compliant with WMA version 10
* Sampling rates (in kHz) - 8, 11, 16, 22, 32,
44.1, 48
* Bit rates - All bit-rates in the range 5kbps to
384kbps
*.wma
WMA
English
HT-C6950W_CIS_ENG_0422.indd 11
11
2010-04-22
1:51:12
Getting Started
USB Host Specification
USB Host Specification
• Supports USB 1.1 or USB 2.0 compliant devices.
• Supports devices connected using the USB
A type cable.
• Supports UMS (USB Mass Storage Device)
V1.0 compliant devices.
• Supports FAT(FAT, FAT16, FAT32) file
system formatting.
• CBI (Control/Bulk/Interrupt) is not supported.
• Digital Cameras that use PTP protocol or
require additional program installation when
connected to a PC are not supported.
• A device using the NTFS file system is not
supported. (Only the FAT 16/32 (File Allocation
Table 16/32) file system is supported.)
• Does not operate with Janus enabled MTP
(Media Transfer Protocol) devices.
USB Devices that can be used with the
product
Non-compliance
• Does not support a device that requires installing
a separate driver on the PC (Windows).
• Does not support connection to a USB hub.
• A USB device that is connected using an
USB extension cable may not be recognized.
Operational Limitations
• If the connected device has multiple drives
(or partitions) installed, only one drive
(or partition) can be connected.
• A device supporting USB 1.1 alone may
cause a difference in the picture quality,
depending on the device.
1. USB Storage Device
2. MP3 Player
3. Digital Camera
4. USB card Reader: One slot USB card reader and
Multi-slot USB card reader.
• The USB card reader may not be supported,
depending on the manufacturer.
• If you install multiple memory devices into a
multi-card reader, you may experience
problems.
✎ NOTE
Supported file Formats
 The external HDD device is not supported.
Format
Still Picture
Music
File name
File extension
Bit rate
Version
Pixel
Sampling Frequency
JPG
JPG .JPEG
–
–
640x480
–
MP3
.MP3
80~384kbps
–
–
44.1kHz
Accessories
Check for the supplied accessories below.
FUNCTION
TV SOURCE
POWER
BD RECEIVER/TV
SLEEP
1
2
4
5
7
8
3
6
9
FULL SCREEN
REPEAT
0
MUTE
TUNING
/CH
VOL
SFE MODE
DISC MENU
MENU
TITLE MENU
POPUP
TOOLS
INFO
RETURN
EXIT
TUNER
MEMORY
A
INTERNET@
Video Cable
12
FM Antenna
User's Manual
B
C
MO/ST
D
DSP
Remote Control/ Batteries
(AAA size)
ASC Microphone
English
HT-C6950W_CIS_ENG_0419.indd 12
2010-04-19
4:41:28
01
Front Panel
1
2
3
4
5
6
7
8
1
2
3
4
DISC TRAY
Insert disc here.
DISPLAY
Displays the playing status, time, etc.
REMOTE CONTROL SENSOR
Detects signals from the remote control.
OPEN/CLOSE BUTTON
Opens and closes the disc tray.
5
FUNCTION BUTTON
6
TUNING DOWN & SKIP BUTTON
7
8
STOP BUTTON
Stops disc playback.
PLAY/PAUSE BUTTON
Plays a disc or pauses playback.
9
TUNING UP & SKIP BUTTON
Goes to the next title/chapter/track.
Tunes up the FM frequency band.
10
11
12
POWER BUTTON (
Turns the product on and off.
13
)
9
10
11 12
13
Getting Started
Description
The mode switches as follows :
BD/DVD D. IN AUX HDMI. IN1 HDMI. IN2 FM
Goes back to the previous title/chapter/track.
Tunes down the FM frequency band.
VOLUME CONTROL
Volume adjustment.
ASC IN JACK
Used to connect the ASC Microphone for setting up MAC (Musical Auto Calibration).
USB PORT
A USB storage device can be connected here and used as storage when connected
to BD-LIVE. It can also be used for software upgrades and MP3/JPEG/DivX/MKV/MP4
playback.
✎ NOTE
 Software upgrades using the USB Port must be performed with a USB memory flash stick only.
English
HT-C6950W_CIS_ENG_0419.indd 13
13
2010-04-19
4:41:45
Getting Started
Rear Panel
1
2
3
4
5
6
DIGITAL
AUDIO IN
HDMI IN
7
8 9
FM ANT
LAN
WIRELESS
10
11
COMPONENT OUT
HDMI OUT
OPTICAL
SPEAKER IMPEDANCE : 3
VIDEO OUT
1
SPEAKER OUTPUT CONNECTORS
Connect the front, centre, surround back, subwoofer speakers.
2
COOLING FAN
The cooling fan supplies cool air to the product to prevent overheating
and always revolves when the power is on.
3
FM 75 COAXIAL JACK
Connect the FM antenna.
4
TX CARD CONNECTION (WIRELESS)
The TX card enables communication between the product and the
wireless receiver module.
5
EXTERNAL DIGITAL OPTICAL IN JACKS
(OPTICAL)
Use this to connect external equipment capable of digital output.
6
HDMI IN JACKS
Receives digital video and audio signals simultaneously using an
HDMI cable.
7
HDMI OUT JACK
Use an HDMI cable, connect this HDMI output terminal to the HDMI
input terminal on your TV for the best quality picture.
8
LAN TERMINAL
Can be used for network based services (see pages 54~59),
BD-LIVE and software upgrade under the network connection.
9
AUX IN JACKS
Connect to the 2CH analogue output of an external device
(such as a VCR)
10
COMPONENT VIDEO OUT JACKS
Connect a TV with Component video inputs to these jacks.
11
VIDEO OUT JACK
Connect your TV's Video Input jack (VIDEO IN) to the VIDEO OUT
Jack on this product.
! CAUTION
 Ensure a minimum of 10 cm of clear space on all sides of the cooling fan when installing the product.
 Do not obstruct the cooling fan or ventilation holes.
14
English
HT-C6950W_CIS_ENG_0407.indd 14
2010-04-08
6:25:53
01
Getting Started
Remote control
Tour of the Remote Control
POWER
FUNCTION
TV SOURCE
BD RECEIVER/TV
SLEEP
Turn the product on and off.
Press to select BD RECEIVER/TV
mode.
Press numeric buttons to operate options.
1
2
3
4
5
6
7
8
0
Allows you to repeat a title, chapter,
track or disc.
Press to search backwards or
forwards.
Press to skip backwards or forwards.
Press to pause a disc.
Press to stop/play a disc.
Cut off the sound temporarily.
MUTE
Adjust the volume.
TUNING
/CH
VOL
SFE MODE
DISC MENU
MENU
TITLE MENU
Press to view the disc menu.
POPUP
TOOLS
INFO
RETURN
EXIT
Select on-screen menu items and
change menu value.
Return to the previous menu.
These buttons are used both for menus
on the product and also several
Blu-ray Disc functions.
Press this to link to various
Internet@TV services.
Select the desired Dolby Pro
Logic II audio mode.
Set a Sleep time to shut off the
procuct.
REPEAT
Press this to see the full screen on a TV.
Press this to use the Tools menu.
To open and close the disc tray.
9
FULL SCREEN
Press this to move to the home
menu.
This is mode selection button.
or
Press to select TV's video mode.
Search for active FM stations and
change channels.
You can set the SFE(Sound Field
Effect) mode best suited for the
type of music you are listening to.
Use this to enter the popup
menu/title menu.
Use this to display the playback
information when playing
a Blu-ray/DVD disc.
Press this to exit the menu.
TUNER
MEMORY
A
INTERNET@
B
C
MO/ST
D
DSP
Used to set a preset radio
frequency.
Select MONO or STEREO for radio
broadcasting.
Regulate and stabilize the volume
level. (Digital Signal Processor)
English
HT-C6950W_CIS_ENG_0407.indd 15
15
2010-04-08
6:25:54
Getting Started
Installing batteries in the Remote Control
* Battery size: AAA
TV Brand Code List
Brand
Code
Brand
Code
Admiral
(M.Wards)
56, 57, 58
Mitsubishi/
MGA
18, 40, 59, 60, 75
A Mark
01, 15
MTC
18
NEC
18, 19, 20, 40, 59, 60
Anam
01, 02, 03, 04, 05,
06, 07, 08, 09, 10,
11, 12, 13, 14
Nikei
03
Onking
03
01, 18, 40, 48
Onwa
03
Panasonic
06, 07, 08, 09, 54,
66, 67, 73, 74
AOC
✎ NOTE
 Make sure to match the “+” and “–” ends of
Bell &
Howell
(M.Wards)
57, 58, 81
Brocsonic
59, 60
Candle
18
Penney
18
Philco
03, 15, 17, 18, 48,
54, 59, 62, 69, 90
Philips
15, 17, 18, 40,
48, 54, 62, 72
Cetronic
03
Citizen
03, 18, 25
Cinema
97
Pioneer
63, 66, 80, 91
Classic
03
Portland
15, 18, 59
Concerto
18
Proton
40
Contec
46
Quasar
06, 66, 67
Coronado
15
Craig
03, 05, 61, 82, 83, 84
Radio
Shack
17, 48, 56, 60,
61, 75
Croslex
62
03
RCA/
Proscan
18, 59, 67, 76, 77,
78, 92, 93, 94
Crown
Curtis
Mates
Realistic
03, 19
59, 61, 63
CXC
03
When operating a TV with the remote control
Daewoo
02, 03, 04, 15, 16,
17, 18, 19, 20, 21,
22, 23, 24, 25, 26,
27, 28, 29, 30, 32,
34, 35, 36, 48, 59, 90
1. Press the BD RECEIVER/TV button to set the
remote control to TV mode.
Daytron
40
Dynasty
03
Emerson
03, 15, 40, 46, 59, 61,
64, 82, 83, 84, 85
Fisher
19, 65
Funai
03
Futuretech
03
General
Electric (GE)
06, 40, 56, 59,
66, 67, 68
Hall Mark
40
Hitachi
15, 18, 50, 59, 69
Inkel
45
JC Penny
56, 59, 67, 86
JVC
70
KTV
59, 61, 87, 88
the batteries with the diagram inside the
compartment.
 Assuming typical TV usage, the batteries last
for about one year.
 The remote control can be used up to
approximately 7 meters in a straight line.
Setting the Remote Control
You can control certain functions of your TV with
this remote control.
2. Press the POWER button to turn on the TV.
3. While holding down the POWER button, enter
the code corresponding to your brand of TV.
• If there is more than one code listed for
your TV in the table, enter one at a time to
determine which code works.
• Example : For a Samsung TV
While holding down the POWER button, use the
number buttons to enter 00, 15, 16, 17 and 40.
4. If the TV turns off, the setting is complete.
• You can use the TV POWER, VOLUME,
CHANNEL, and Numeric buttons (0~9).
✎ NOTE
 The remote control may not work on some
brands of TV's. Also, some operations may not
be possible, depending on your brand of TV.
 The remote control will work with Samsung TVs
by default.
16
KEC
03, 15, 40
KMC
15
LG
(Goldstar)
01, 15, 16, 17, 37, 38,
39, 40, 41, 42, 43, 44
Sampo
40
Samsung
00, 15, 16, 17, 40,
43, 46, 47, 48, 49,
59, 60, 98
Sanyo
19, 61, 65
Scott
03, 40, 60, 61
Sears
15, 18, 19
Sharp
15, 57, 64
Signature
2000
(M.Wards)
57, 58
Sony
50, 51, 52, 53, 55
Soundesign
03, 40
Spectricon
01
SSS
18
Sylvania
18, 40, 48, 54,
59, 60, 62
Symphonic
61, 95, 96
Tatung
06
Techwood
18
Teknika
03, 15, 18, 25
TMK
18, 40
Toshiba
19, 57, 63, 71
Vidtech
18
Videch
59, 60, 69
Luxman
18
Wards
LXI
(Sears)
15, 17, 18, 40,
48, 54, 60, 64
19, 54, 56, 59,
60, 62, 63, 65, 71
Yamaha
18
York
40
Magnavox
15, 17, 18, 48, 54,
59, 60, 62, 72, 89
Yupiteru
03
Marantz
40, 54
Zenith
58, 79
Matsui
54
Zonda
01
MGA
18, 40
Dongyang
03, 54
English
HT-C6950W_CIS_ENG_0407.indd 16
2010-04-08
6:25:55
02
Connections
Connections
This section involves various methods of connecting the product to other external components.
Before moving or installing the product, be sure to turn off the power and disconnect the power cord.
Connecting the Speakers
6.6~9.8 feet (2~3m)
BD
SL
SR
SBL
SBR
Position of the product
Place it on a stand or cabinet shelf, or under the TV stand.
Selecting the Listening Position
The listening position should be located about 2.5 to 3 times the distance of the TV's screen size away from the TV.
Example : For 32" TV's 2~2.4m
For 55" TV's 3.5~4m
Front Speakers ei
Place these speakers in front of your listening position, facing inwards (about 45°)
toward you. Place the speakers so that their tweeters will be at the same height as your
ear. Align the front face of the front speakers with the front face of the centre speaker or
place them slightly in front of the centre speakers.
Centre Speaker f
It is best to install it at the same height as the front speakers. You can also install it
directly over or under the TV.
Surround Speakershj
Place these speakers to the side of your listening position. If there isn't enough room,
place these speakers so they face each other. Place them about 60 to 90cm above
your ear, facing slightly downward.
the front and centre speakers, the surround speakers are used to handle
* Unlike
mainly sound effects and sound will not come from them all the time.
Surround Back Speakers SBL SBR
If you are using two rear centre speakers, place them behind the listening position.
Place the surround back speaker about 70 cm to 1 m.
Subwoofer g
The position of the subwoofer is not so critical. Place it anywhere you like.
English
HT-C6950W_CIS_ENG_0407.indd 17
17
2010-04-08
6:25:55
Connections
Connecting the Speakers
Speaker Components
Assembled Speakers
(L) (R)
SCREW (Large): 4EA
SCREW (Small): 16EA
STAND
FRONT
CENTRE
¨
CENTRE SPEAKER
STAND BASE
(L) (R)
FRONT/SURROUND SPEAKER
(L) (R)
SUBWOOFER
SURROUND
SURROUND BACK
SPEAKER CABLE
SURROUND BACK
SPEAKER
SUBWOOFER
SWA-5000
TX Card
Wireless Receiver Module
Speaker Cable (2EA)
✎ NOTE
 Refer to page 19 to install the Speakers on the Tallboy Stand.
18
English
HT-C6950W_CIS_ENG_0407.indd 18
2010-04-08
6:25:56
02
Connections
Installing the Speakers on the Tallboy Stand
1. Turn the Stand Base upside-down and connect it to the Stand.
1
Stand
Base
Stand
2. Insert four small screws clockwise into the four holes marked using a
screwdriver as shown in the illustration.
2
3. Connect the upper Speaker to the assembled Stand.
3
Speaker
Stand
4. Insert another large screw clockwise into the hole on the rear of the
speaker using a screwdriver.
4
English
HT-C6950W_CIS_ENG_0407.indd 19
19
2010-04-08
6:26:10
Connections
Connecting the Speakers
Connecting The Speakers
1. Press down the terminal tab on the back of the speaker.
2. Insert the black wire into the black terminal (–) and the red wire into
the red (+) terminal, and then release the tab.
3. Connect the connecting plugs to the back of the product by
matching the colours of the speaker plugs to the speaker jacks.
4. With the product turned off, insert the TX card into the TX Card
Connection(WIRELESS) on the back of the product.
• Hold the TX card so that the label "WIRELESS" faces upward and
insert the card into the port.
• The TX card enables communication between the product
and the wireless receiver module.
5. Connect the left and right surround speakers to the wireless
receiver module.
6. Plug the power cord of the wireless receiver module in the
wall outlet.
7. Turn on the product. The product and wireless receiver
module will now communicate with each other and you will
hear sound from the Surround speakers.
Black
Red
TX card
Front Speaker (R)
Front Speaker (L)
Centre Speaker
Surround Speaker (L)
Surround Speaker (R)
Surround Back Speaker (R)
Surround Back Speaker (L)
SPEAKER IMPEDANCE : 3
FM ANT
WIRE
W
Wireless Receiver Module
Subwoofer
SPEAKER IMPEDANCE : 3
This product should be connected with the SWA-5000 only.
20
English
HT-C6950W_CIS_ENG_0407.indd 20
2010-04-08
6:26:10
02
 Do not let children play with or near the speakers. They could get hurt if a speaker falls.
 When connecting the speaker wires to the speakers, make sure that the polarity (+/–) is correct.
 Keep the subwoofer speaker out of reach of children so as to prevent children from inserting their
Connections
! CAUTION
hands or alien substances into the duct (hole) of the subwoofer speaker.
 Do not hang the subwoofer on the wall through the duct (hole).
 Do not insert any other card except the TX card dedicated to the product.






If a different TX card is used, the product may be damaged or the card may not be removed
easily.
Do not insert the TX card upside down or in the reverse direction.
Insert the TX card when the product is turned off. Inserting the card when it is turned on may
cause a problem.
The wireless receiving antenna is built into the wireless receiver module. Keep it away from water
and moisture.
For optimal listening performance, make sure that the area around the wireless receiver module
location is clear of any obstructions.
If no sound is heard from the wireless surround speakers, switch the mode to DVD 5.1 channel or
Dolby Pro Logic II.
In 2-CH mode, no sound will be heard from the wireless surround speakers.
✎ NOTE
 If you place a speaker near your TV set, screen colour may be distorted because of the magnetic
field generated by the speaker. If this occurs, place the speaker away from your TV set.
 Place the wireless receiver module at the rear of the listening position. If the wireless receiver
module is too close to the product, some sound interruption may be heard due to interference.
 If you use a device such as a microwave oven, wireless LAN Card or any other device that uses
the same frequency (2.4/5.8GHz) near the product, some sound interruption may be heard due
to interference.
 The transmission distance from the product to the wireless receiver module is about 10m, but
may vary depending on your operating environment. If a steel-concrete wall or metallic wall is
between the product and the wireless receiver module, the system may not operate at all,
because the radio wave cannot penetrate metal.
 If the product doesn't make wireless connection, the system needs ID Setting between the
product and wireless receiver module. With the product turned off, press the remote control's
number buttons "0"J"1"J"3"J"5" and turn on the product. With the wireless receiver module
turned on, press "ID SET" button on the back of the wireless receiver module for 5 seconds.
English
HT-C6950W_CIS_ENG_0407.indd 21
21
2010-04-08
6:26:12
Connections
Connecting External Devices/your TV via HDMI
HDMI is a standard digital interface for connection to such devices as a TV, projector, DVD player, Blu-ray
player, set top box and more.
HDMI removes any loss of signal from analogue conversion, enabling you to enjoy video and audio sound
quality as it was originally created in the digital source.
DVD or Blu-ray Player
SAT(Satellite/Set top box)
HDMI IN
FM ANT
LAN
WIRELESS
DIGITAL
AUDIO IN
HDMI IN
COMPONENT OUT
HDMI OUT
OPTICAL
SPEAKER IMPEDANCE : 3
VIDEO OUT
HDMI OUT
HDMI OUT : Connecting to a TV with an HDMI Cable (BEST QUALITY)
Connect an HDMI cable (not supplied) from the HDMI OUT jack on the back of the product to the
HDMI IN jack on your TV.
✎ NOTE
 Certain HDMI output resolutions may not work, depending on your TV.
 If an HDMI cable is connected or removed during playback of a CD-DA, MP3 or JPEG file, the product will
stop playing.
 After making the video connection, set the Video input source on your TV to match the corresponding Video
output (HDMI, Component or Composite) on your product.
See your TV owner's manual for more information on how to select the TV's Video Input source.
 If you have set the product's remote control to operate your TV, press the SOURCE button on the remote
control and select HDMI as the external source of the TV.
 You must have an HDMI connection to enjoy videos with 3D technology.
 A long HDMI cable may cause a screen noise. If this is the case, set Deep Color to Off in the menu.
22
English
HT-C6950W_CIS_ENG_0407.indd 22
2010-04-08
6:26:13
02
1. Connect an HDMI cable (not supplied) from the HDMI IN jack on the back of the product to the
HDMI OUT jack on your digital devices.
Connections
HDMI IN : Connecting to an External Component with an HDMI Cable
2. Press the FUNCTION button to select HDMI. IN1 or HDMI. IN2 input.
The mode switches as follows : BD/DVD D. IN AUX HDMI. IN1 HDMI. IN2 FM
HDMI Auto Detection Function
The product's video output will automatically change to HDMI mode when connecting an HDMI cable
before power is on. For possible HDMI resolutions, see page 32.
• This function is not available if the HDMI cable does not support CEC.
• HDMI connection description
- HDMI outputs only a pure digital signal to the TV.
- If your TV does not support HDCP, random noise appears on the screen.
• What is the HDCP?
HDCP (High-band width Digital Content Protection) is a system for protecting BD/DVD content outputted via
HDMI from being copied. It provides a secure digital link between a video source (PC, DVD. etc) and a display
device (TV, projector. etc). Content is encrypted at the source device to prevent unauthorized copies from being
made.
! CAUTION
 The Anynet+ function is supported only when an HDMI Cable is connected to the HDMI OUT of the
product.
English
HT-C6950W_CIS_ENG_0407.indd 23
23
2010-04-08
6:26:14
Connections
Connecting the Video Out to your TV
Red
Blue
Green
METHOD 1
LAN
COMPONENT OUT
METHOD 2
Yellow
VIDEO OUT
METHOD 1 : Component Video (BETTER QUALITY)
If your television is equipped with Component Video inputs, connect a Component video cable (not
supplied) from the Component Video Output (Pr, Pb and Y) Jacks on the back of the product to the
Component Video Input Jacks on your TV.
✎ NOTE
 You can select from a variety of resolution settings such as 1080i, 720p, 576p(480p) and 576i(480i),
depending on the disc type. (See page 32)
 The actual resolution may differ from the setting in the Setup menu if both Component and HDMI cables are
connected.
The resolution may also be different depending on the disc. (See page 32)
 After making the video connection, set the Video input source on your TV to match the corresponding Video
output (HDMI, Component or Composite) on your product.
See your TV owner's manual for more information on how to select the TV's Video Input source.
 If you have set the product's remote control to operate your TV, press the TV SOURCE button on the remote
control and select COMPONENT as the external source of the TV.
 In DVD playback, if both HDMI and Component jacks are connected and you select the Component 1080p,
1080i, 720p or 576p(480p) mode, the Display Setup menu will show the output resolution as 1080p, 1080i,
720p or 576p(480p) in the menu. The resolution is actually 576i(480i).
METHOD 2 : Composite Video (GOOD QUALITY)
Connect the supplied Video cable from the VIDEO OUT jack on the back of the product to the VIDEO
IN jack on your TV.
✎ NOTE
 The VIDEO source is always output in 576i(480i) resolution regardless of the resolution set in the Setup
menu. (See page 32)
 After making the video connection, set the Video input source on your TV to match the corresponding
Video output (HDMI, Component or Composite) on your product.
See your TV owner's manual for more information on how to select the TV's Video Input source.
 If you have set the product's remote control to operate your TV, press the TV SOURCE button on
the remote control and select VIDEO as the external source of the TV.
! CAUTION
 Do not connect the unit through a VCR. Video signals fed through VCRs may be affected by
copyright protection systems and the picture will be distorted on the television.
24
English
HT-C6950W_CIS_ENG_0407.indd 24
2010-04-08
6:26:14
02
Connections
Connecting Audio from External Components
LAN
DIGITAL
AUDIO IN
HDMI IN
COMPONENT OUT
HDMI OUT
OPTICAL
VIDEO OUT
Red
Optical Cable
(not supplied)
Set-Top Box
OPTICAL
White
Audio Cable
(not supplied)
If the external analogue
component has only one
Audio Out, connect either
left or right.
VCR
AUX
OPTICAL : Connecting an External Digital Component
Digital signal components such as a Cable Box/Satellite receiver (Set-Top Box).
1. Connect the Digital Input (OPTICAL) on the product to the Digital Output of the external digital
component.
2. Press the FUNCTION button to select D.IN input.
• The mode switches as follows : BD/DVD D. IN AUX HDMI. IN1 HDMI. IN2 FM
✎ NOTE
 To see video from your Cable Box/Satellite receiver, you must connect it's video output to a TV.
 This system supports Digital sampling frequencies of 32 kHz of higher from external digital components.
 This system supports only DTS and Dolby Digital audio, MPEG audio which is bitstream cannot be supported.
AUX : Connecting an External Analogue Component
Analogue signal components such as a VCR.
1. Connect AUX IN (Audio) on the product to the Audio Out of the external analogue component.
• Be sure to match connector colours.
2. Press the FUNCTION button to select AUX input.
• The mode switches as follows : BD/DVD D. IN AUX HDMI. IN1 HDMI. IN2 FM
✎ NOTE
 You can connect the Video Output jack of your VCR to the TV, and connect the Audio Output jacks of
the VCR to this product.
English
HT-C6950W_CIS_ENG_0407.indd 25
25
2010-04-08
6:26:14
Connections
Connecting to the Network
This product enables you to view network based services (See pages 54~59) such as Internet@TV and
BD-LIVE, as well as receive software upgrades when a network connection is made. We recommend
using an AP (Access Point) or IP router for the connection.
For more information on router connection, refer to the user manual of the router or contact the router
manufacturer for technical assistance.
Cable Network
1. Using the Direct LAN Cable (UTP cable), connect the LAN terminal of the product to the LAN
terminal of your modem.
2. Set the network options. (See page 39)
LAN
COMPONENT OUT
Y
HDMI IN
HDMI OUT
VIDEO OUT
Router
Broadband modem
(with integrated router)
Or
Broadband modem
Broadband
service
Broadband
service
Networking with PC for
AllShare function
(See pages 58~59)
✎ NOTE
 Internet access to Samsung’s software update server may not be allowed, depending on the router you use or the
ISP’s policy. For more information, contact your ISP (Internet Service Provider).
 For DSL users, please use a router to make a network connection.
 For the AllShare function, a PC must be connected in the network as shown in the figure.
26
English
HT-C6950W_CIS_ENG_0407.indd 26
2010-04-08
6:26:15
02
FM Antenna (supplied)
1. Connect the FM antenna supplied to the
FM 75Ω COAXIAL Jack.
FM ANT
WIRELESS
DIGIRA
AODIO I
OPTICA
Connections
Connecting the FM Antenna
2. Slowly move the antenna wire around until
you find a location where reception is good,
then fasten it to a wall or other rigid surface.
✎ NOTE
 This product does not receive AM
broadcasts.
English
HT-C6950W_CIS_ENG_0407.indd 27
27
2010-04-08
6:26:17
Setup
Before Starting (Initial Settings)
1. Turn on your TV after connecting the product.
(When the product is connected to TV for the first
time, product will turn on automatically and the
Initial Settings screen will be displayed.)
Initial Settings I On-Screen Language
7. Press the ENTER button. If you selected a
Network Setting, go to pages 39~40 for
more information about the Network settings.
When done, go to Step 8.
8. Press the OK button.
The home menu will be displayed. (For more
information about home menu, please see
page 29)
Select a language for the on-screen displays.
• Home Menu
English
Français
Deutsch
Español
You Tube
internet radio service
Please activate Internet@TV
to enjoy a variety of Internet Services.
Italiano
Nederlands
> Move
s Select
2. Press the ▲▼ buttons to select the desired
language, then press the ENTER button.
3. Press the ENTER button to select Start button.
a Change Device
d View Devices
" Enter
✎ NOTE
Initial Settings
TV Aspect, Musical Auto Calibration and Network will be set.
 When the product is connected to TV for the
Each setting may be changed later under "Settings"
Start
a Previous
No Disc
" Select
4. Press the ▲▼ buttons to select desired TV
Aspect ratio, then press the ENTER button.
(See page 31)
Musical Auto Calibration screen will be displayed.
5. Plug the ASC microphone into the ASC IN jack
on the product. (See page 35)
6. Press the ENTER button to select Start button.
first time, product will turn on automatically.
Do not confuse because this is not
malfunction.
 The home menu will not be displayed if you do
not configure the initial settings.
 If you press the BLUE(D) button during the
Musical Auto Calibration/Network setup, you
can access the home menu even if the
network setup is not completed yet.
 When you return to home menu, the full
screen mode will be cancelled automatically.
Initial Settings I Musical Auto Calibration
Preparing...
d Skip
Setting the Musical Auto Calibration function
takes about 3 minutes.
28
English
HT-C6950W_CIS_ENG_0407.indd 28
2010-04-08
6:26:17
03
again in order to make changes, press the
STOP () button on the front panel of the
product for more than 5 seconds with no disc
inserted.
 Use the HDMI cable to connect the product to
an Anynet+(HDMI-CEC)-compliant Samsung TV.
If the TV uses a language supported by the
product, that language will be set to a
preferred language automatically.
However, the Anynet+(HDMI-CEC) feature
should be set to On in both TV and the
product.
 If the product is left in the stop mode for more
than 5 minutes without being operated, a
screen saver will appear on your TV. If the
product is left in the screen saver mode for
more than 25 minutes, the power will
automatically turn off except during playback
of a CD-DA (Automatic Power-Off Function).
Setting the Menu
DISC MENU
MENU
1. Press the POWER button.
The Home Menu will appear.
• Home Menu
You Tube
internet radio service
Please activate Internet@TV
to enjoy a variety of Internet Services.
2
3
4
1
5
No Disc
a Change Device
1
Selects the Internet@TV.
2
Selects the Videos.
3
Selects the Music.
4
Selects the Photos.
5
Selects the Settings.
6
Displays buttons available.
d View Devices
POPUP
TOOLS
INFO
3
RETURN
EXIT
4
TUNER
1
MENU Button : Press this to move to the home menu.
2
RETURN Button : Return to the previous menu.
3
ENTER / DIRECTION Button:
Press the arrow buttons to move the cursor and select
an item.
Press the ENTER button to launch the selected item or
confirm the setting.
4
EXIT Button : Press this to exit the menu.
2. Press the ◄► buttons to select Settings,
then press the ENTER button.
3. Press the ▲▼ buttons to select the desired
submenu, then press the ENTER button.
4. Press the ▲▼ buttons to select the desired
item, then press the ENTER button.
5. Press the EXIT button to exit the menu.
✎ NOTE
 When the product is connected to the network,
select Internet@TV from the home menu.
Download desired content from Samsung AppS.
 The access step may differ depending on the
selected menu.
 The OSD (On Screen Display) may change in
this product after upgrading the software
version.
English
HT-C6950W_CIS_ENG_0407.indd 29
6
" Enter
TITLE MENU
1
2
Setup
 If you want to display Initial Settings screen
29
2010-04-08
6:26:20
Setup
Display
You can configure various display options such
as the TV Aspect, Resolution, 3D, etc.
3D
Select whether to play a Blu-ray Disc with 3D
contents in 3D Mode.
Settings
Display
3D
3D
Audio
System 3D Mode
: Auto
NetworkTV Screen Size :
55 inch
Language
Security
General
> Move s Select r Return
Still Mode
: Auto
Support
TV Screen Size
Lets you enter the actual screen size of your
TV so that the product can adjust the image
according to the screen size and display an
optimal 3D image. (The maximum allowed
screen size is 116 inches for this product.)
! CAUTION
 If you want to enjoy a 3D content, connect a
3D device (3D compliant AV receiver or TV)
to the product and wear a 3D glass before
playing the 3D content.
 While watching the 3D video, all analog
component and composite signals will be
blocked automatically.
 All 3D signals are output only using the
HDMI cable and through the HDMI OUT
port.
3D Mode
• Auto : The 3D Blu-ray Disc is played in 3D
mode if your product detects a TV which
supports it. It is played in 2D mode if your
product detects a TV which cannot support it.
• 3D : The 3D Blu-ray Disc is played in 3D mode
at all times. If a TV cannot support 3D Blu-ray
discs, the TV's screen can be black.
• 2D : The 3D Blu-ray Disc is played in 2D mode
at all times. Choose this to view a picture
without 3D effect or when a TV cannot support
3D Blu-ray discs.
✎ NOTE
 If you press the STOP() button once during
the 3D disc playback, 3D mode option will not
be deactivated.
To activate 3D mode option during the 3D disc
playback, press the STOP() button twice.
 As the video resolution in 3D play mode is
fixed according to the resolution of the
original 3D video, you can not change the
resolution to your preference.
 Some functions such as BD Wise, or setting
the screen size or resolution may not
operate properly in 3D play mode.
 You must use a high-speed HDMI cable for
a proper output of the 3D signal.
 Stay at least three times of the length of the
screen distant from the TV.
- It is recommended to place the 3D video
screen forward at eye level.
 If the product is connected to some 3D
devices, the 3D effect may not function
properly.
 You can not use this product for switching a
2D content to 3D.
 Depending on the content and its play position,
vertical black bars could be seen on left or right
or both sides.
30
English
HT-C6950W_CIS_ENG_0407.indd 30
2010-04-08
6:26:22
03
BD Wise (Samsung Products only)
Depending on the type of television you have, you
may want to adjust the screen setting.
BD Wise is Samsung's latest inter-connectivity feature.
• 16:9 Normal
Certain movies(4:3 source)
will be displayed in 4:3
Pillarbox (black bars on sides
of picture) if 16:9 normal is
selected.
• 16:9 Wide
You can view the full 16:9
picture on your widescreen
TV.
• 4:3 Letter Box
Select when you want to see
the total 16:9 ratio screen a
Blu-ray Disc/DVD supplies,
even though you have a TV
with a 4:3 ratio screen. Black
bars will appear at the top
and bottom of the screen.
• 4:3 Pan-Scan
Select when you want to see
the 16:9 video supplied by the
Blu-ray Disc/DVD without the
black bars on top and bottom,
even though you have a TV
with a 4:3 ratio screen(extreme
left and right portion of the
movie picture will be cut off).
✎ NOTE
 Depending on the disc type, some aspect ratios
may not be available.
 If you select an aspect ratio and option which is
different than the aspect ratio of your TV screen,
then the picture might appear to be distorted.
 If you select the 4:3 Pan-Scan or 4:3 Letter Box,
you can't see full screen by pressing the FULL
SCREEN button on the remote control.
When you connect Samsung products with
BD-Wise to each other via HDMI, the optimum
resolution will be set automatically.
• Off : The output resolution will be fixed
according to the Resolution previously set,
regardless of the resolution of the disc.
• On : The original resolution of the BD/DVD disc
will be output to the TV.
✎ NOTE
 If you want to change the resolution in BD
Wise, you must set BD Wise to Off in advance.
 If you set off the BD Wise, the resolution of the
connected TV will be adjusted to its maximum
resolution automatically.
 If the product is connected to a device that
does not support BD Wise, you can not use
BD Wise function.
 For a proper operation of BD Wise, set the BD Wise
menu of both the product and the TV to On.
Resolution
Sets the output resolution of the Component and
HDMI video signal.
The number in 1080p, 1080i, 720p, 576p(480p),
576i(480i) indicates the number of lines of video.
The i and p indicate interlace and progressive
scan, respectively.
• Auto : It automatically checks and sets the optimal
resolution. (HDMI only)
• BD Wise : Automatically sets the optimal
resolution when connected via HDMI to a TV with
the BD Wise feature. (The BD Wise menu item
appears only if BD Wise is set to On.) (HDMI only)
• 1080p : Outputs 1080 lines of progressive video. (HDMI only)
• 1080i : Outputs 1080 lines of interlaced video.
• 720p : Outputs 720 lines of progressive video.
• 576p/480p : Outputs 576(480) lines of progressive
video.
• 576i/480i : Outputs 576(480) lines of interlaced
video. (Component & VIDEO only)
English
HT-C6950W_CIS_ENG_0407.indd 31
Setup
TV Aspect
31
2010-04-08
6:26:22
Setup
Resolution according to the output mode
• Blu-ray Disc playback
HDMI / connected
Output
Setup
HDMI / not connected
HDMI Mode
Component/VIDEO Mode
Component Mode
VIDEO Mode
Auto
Optimal Resolution
576i(480i)
-
-
1080p, Movie Frame(24Fs) off
1080p@60F
576i(480i)
-
-
1080p/1080i,
Movie Frame(24Fs) on
1080p@24F
576i(480i)
-
-
1080i, Movie Frame(24Fs) off
1080i
576i(480i)
1080i
576i(480i)
720p
720p
576i(480i)
720p
576i(480i)
576p(480p)
576p(480p)
576i(480i)
576p(480p)
576i(480i)
576i(480i)
-
-
576i(480i)
576i(480i)
• DVD playback
HDMI / connected
Output
Setup
HDMI Mode
Component/VIDEO Mode
Component Mode
VIDEO Mode
Auto
Optimal Resolution
576i(480i)
-
-
1080p
1080p@60F
576i(480i)
-
-
1080i
1080i
576i(480i)
576p(480p)
576i(480i)
720p
720p
576i(480i)
576p(480p)
576i(480i)
576p(480p)
576p(480p)
576i(480i)
576p(480p)
576i(480i)
576i(480i)
-
-
576i(480i)
576i(480i)
✎ NOTE
 If the connected TV does not support Movie
Frame or the selected resolution, the message
“If no pictures are shown after the selection,
please wait for 15 seconds. And then, the
resolution will be reverted to the previous value
automatically. Would you like to make a
selection?” will be displayed.
If you select Yes and the resolution is not
supported, the TV's screen will be blank.
Please wait for 15 seconds and the resolution
will be reverted to the previous value
automatically.
 If the screen is blank, press and hold the
STOP () button on the front of the product
for more than 5 seconds (no disc inserted).
All settings are restored to the factory default.
Follow the steps on the previous page to
access each mode and select the Display
Setup that your TV will support.
32
HDMI / not connected
 When the factory default settings are restored,
all the user data stored in the BD data will be
deleted.
 The Blu-ray Disc must have the 24 frame
feature in order to use the Movie Frame (24Fs)
mode.
 If both HDMI and Component jacks are
connected and you are currently viewing
component output, there is a difference
between resolution table and actual resolution
depending on your TV.
 If the HDMI Auto Detection feature does not
work, you can't select the 1080p resolution or
Movie Frame (24Fs).
English
HT-C6950W_CIS_ENG_0407.indd 32
2010-04-08
6:26:26
03
Setup
HDMI Format
Progressive Mode
You can optimize the colour setting from the
HDMI output. Select a connected device Type.
Set to improve picture quality when viewing DVDs.
• TV : Select if connected to a TV via HDMI.
• Monitor : Select if connected to a Monitor via
HDMI.
✎ NOTE
 A TV or monitor has to be connected to the
product before you select this option.
Movie Frame (24 Fs)
Setting the Movie Frame (24Fs) feature to On
allows you to adjust the product's HDMI output to
24 frames per second for improved picture quality.
You can enjoy the Movie Frame (24Fs) feature only
on a TV supporting this frame rate. This menu can
only be selected in 1080i or 1080p HDMI output
resolution modes.
• Off : Movie Frame (24Fs) functions will not
work.
• On : Movie Frame (24Fs) functions will work.
✎ NOTE
 Two types of frame rates may be included,
depending on the disc: Movie material (24
frame) and Video material (30 frame). When the
setting switches between Movie (24 frame) and
Video (30 frame), the screen may blink for a
few seconds.
 If your TV does not support Movie Frame
(24Fs) function, the pop-up message will be
displayed.
• Auto : Select this to have the product
automatically set the best picture for the DVD
you're watching.
• Video : Select this for the best picture from
Concert or TV show DVDs.
Still Mode
Set the type of picture shown when you pause
DVD playback.
• Auto: Automatically set the best still picture
depending on the content.
• Frame : Select when pausing a scene with a
little action.
• Field : Select when pausing a scene with a lot
of action.
HDMI Deep Color
Set to output the picture from the HDMI OUT jack
with Deep Colour or not. Deep Colour allows more
accurate colour reproduction with deeper colour
depth.
• Auto: The picture will be output with Deep
Colour to the connected TV which supports
HDMI Deep Colour.
• Off : The picture will be output without Deep
Colour.
English
HT-C6950W_CIS_ENG_0407.indd 33
33
2010-04-08
6:26:26
Setup
Distance
Audio
Speaker Setting
DPL llz
• Off : Select when you place the Surround Back
speakers as shown.
• On : Provide a more realistic 3D surround
sound with vertical surround system.
Settings
Display
Audio
System
Network
Language
Security
General
Support
Speaker Setting
DPL IIz
:
◄
Off |
Level
Distance
Test tone
:
Off
If the speakers cannot be placed at equal
distances from the listening position, you can
adjust the delay time of the audio signals from the
front, centre, surround, surround back and
subwoofer speakers.
• You can set the Speaker Distance between
1ft(0.3m) and 30ft(9.0m).
Settings
Display
Audio
System
Network
Language
Security
General
Support
Distance
Front L
: ◄ 10ft (3.0m) |
Front R
: 10ft (3.0m)
Center
: 10ft (3.0m)
Surround L
: 10ft (3.0m)
Surround R
: 10ft (3.0m)
Surround Back L : 10ft (3.0m)
Surround Back R : 10ft (3.0m)
Subwoofer
: 10ft (3.0m)
Test Tone
:
Off
<Change r Return
<Change r Return
Test Tone
✎ NOTE
 When selecting DPLII Mode, you can listen
to 7.1 channel sound from 2CH, 5.1CH
audio. With 7.1 channel audio, you can
listen to 7.1 channel sound as it is.
Level
You can adjust the balance and level for each
speaker.
Adjusting Front/Centre/Surround
/Surround Back/Subwoofer Speaker Level
• The volume level can be adjusted in steps from
+6dB to -6dB.
• The sound gets louder as you move closer to
+6dB and quieter as you get closer to -6dB.
Settings
Display
Audio
System
Network
Language
Security
General
Support
34
Level
Front L
:
Front R
:
Center
:
Surround L
:
Surround R
:
Surround Back L :
Surround Back R :
Subwoofer
:
Test Tone
:
◄ 0 dB |
0 dB
0 dB
0 dB
0 dB
0 dB
0 dB
0 dB
Off
<Change r Return
Use the Test Tone feature to check the speaker
connections.
Press the ◄, ► buttons to select All.
• A test tone will be sent to Front Left Centre Front Right Surround Right Surround Back L Surround Back R Surround Left Subwoofer in order so you can
make sure the speakers are set up correctly.
To stop the test tone, press the ◄, ► buttons to
select Off.
Settings
Display
Audio
System
Network
Language
Security
General
Support
Speaker Setting
DPL IIz
:
Off
Level
Distance
Test Tone
:◄
<Change
All
|
r Return
✎ NOTE
 When HDMI Audio is ON (audio is produced
through TV speakers), the Test Tone
function is not available.
English
HT-C6950W_CIS_ENG_0407.indd 34
2010-04-08
6:26:26
03
By setting the Musical Auto Calibration (MAC)
function just once when you relocate or install the
product, you can have the product automatically
recognize the distance between speakers, levels
between channels, and frequency characteristics
to create a 7.1-channel sound field optimized for
your environment.
✎ NOTE
Setup
Musical Auto Calibration
 Setting the Musical Auto Calibration
function takes about 3 minutes.
 The Musical Auto Calibration setup can be made
when there is no disc in the product.
 If the ASC microphone is disconnected during the
Musical Auto Calibration setup, the setup will be
cancelled.
 When the Musical Auto Calibration function is
activated, the DSP, Dolby Pro Logic ll and SFE
Mode will not work.
 If the product is connected to external devices or
other components (such as an AUX, D.IN), the
Musical Auto Calibration Setup may not work
properly.
HDMI Audio
ASC
microphone
Musical Auto Calibration
You will hear either the Musical Auto Calibration
mode or the User Speaker Settings.
• Off: You will hear sound in the the Speaker
Setting value.
• On: You will hear sound in the Musical Auto
Calibration mode.
The audio signals transmitted over the HDMI
Cable can be toggled On/Off.
• Off : Video is transmitted over the HDMI
connection cable only, and audio is output
through your product speakers only.
• On : Both video and audio signals are
transmitted over the HDMI connection cable,
and audio is output through your TV speakers
only.
✎ NOTE
 HDMI Audio is automatically down-mixed to
2ch for TV speakers.
Musical Auto Calibration Setting
1. Plug the ASC microphone into the ASC IN jack.
2. Place the ASC microphone at the listening position.
• Musical Auto Calibration will be automatically
set up in the following sequence:
Front Left Centre Front Right Surround Right Surround Back L
Surround Back R Surround Left Subwoofer
• Press the RETURN button to cancel the
Musical Auto Calibration Setting.
English
HT-C6950W_CIS_ENG_0407.indd 35
35
2010-04-08
6:26:28
Setup
✎ NOTE
Digital Output
Set Digital output depending on the connected
receiver. (For more details, please refer to the
digital output selection)
 Be sure to select the correct Digital Output
or you will hear no sound or a loud noise.
 If the HDMI device (Receiver, TV) is not compatible
with compressed formats (Dolby digital, DTS), the
audio signal outputs as PCM.
• PCM
• Bistream(Re-encode)
• Bistream(Audiophile)
 Secondary and Effect audio will not be heard with
regular DVDs.
Blu-ray Discs may include three audio streams.
 Some Blu-ray Discs do not have Secondary and
- Primary Audio : The audio soundtrack of the
main feature.
 This Digital Output setup does not effect the
- Secondary Audio : Additional soundtrack
such as director or actor's commentary.
- Interactive Audio : Interactive sounds will be
heard when selected. Interactive Audio is
different on each Blu-ray Disc.
Effect audio.
analogue (L/R) audio or HDMI audio output to
your TV.
It effects the optical and HDMI audio output when
connected to a receiver.
 If you play MPEG audio soundtracks, audio signal
outputs PCM regardless of Digital Output
Selections (PCM or Bitstream).
Digital Output Selection
Setup
Connection
Definition for
Blu-ray Disc
36
Bitstream
(Audiophile)
HDMI Receiver
Optical
PCM
Up to 7.1ch
PCM 2ch
DTS re-encoded
PCM
PCM 2ch
Dolby Digital
Up to 5.1ch
PCM 2ch
DTS re-encoded
Dolby Digital
Dolby Digital
Dolby Digital
Plus
Up to 7.1ch
PCM 2ch
DTS re-encoded
Dolby Digital Plus
Dolby Digital
Audio Stream
on Blu-ray Disc Dolby TrueHD
Audio Stream
on DVD
Bitstream
(Re-encode)
PCM
HDMI Receiver or Optical HDMI Receiver
Optical
Up to 7.1ch
PCM 2ch
DTS re-encoded
Dolby TrueHD
Dolby Digital
DTS
Up to 6.1ch
PCM 2ch
DTS re-encoded
DTS
DTS
DTS-HD HRA
Up to 7.1ch
PCM 2ch
DTS re-encoded
DTS-HD HRA
DTS
DTS-HD MA
Up to 7.1ch
PCM 2ch
DTS re-encoded
DTS-HD MA
DTS
PCM
PCM 2ch
PCM 2ch
PCM 2ch
PCM 2ch
PCM 2ch
Dolby Digital
Up to 5.1ch
PCM 2ch
Dolby Digital
Dolby Digital
Dolby Digital
DTS
Up to 6.1ch
PCM 2ch
DTS
DTS
DTS
Any
Decodes Primary, Secondary and
Effect audio streams together into
PCM audio.
Outputs only the Primary audio
Decodes Primary, Secondary and
soundtrack (main soundtrack of the
Effect audio streams together into
movie) so that your receiver can decode
PCM audio, then re-encodes the
the audio bitstream. You will not hear
PCM audio into DTS bitstream.
Secondary and Effect audio.
English
HT-C6950W_CIS_ENG_0407.indd 36
2010-04-08
6:26:29
03
You can listen at low volumes but still hear dialog
clearly. This is only active when a Dolby Digital
signal is detected.
• Auto : The Dynamic Range Control will be set
automatically based on the information
provided by the Dolby TrueHD Soundtrack.
• Off : Turn Dynamic Range Control off.
• On : Choose to listen to a movie at a lower
volume without losing clarity of dialog.
Setup
Dynamic Range Control
You can operate this product using a Samsung
TV remote control and start disc playback simply
by pressing the PLAY (►) button on the TV’s
remote control.
For more information, please see the TV user
manual.
• Off : Anynet+ function will not work.
• On : Anynet+ function will work.
✎ NOTE
 This function is not available if the HDMI cable
does not support CEC.
AV Sync
 If your Samsung TV has an n logo, then
Video may look slower than the audio when the
product is connected to a digital TV. If this occurs,
adjust the audio delay time to match the video.
• You can set the audio delay time between
0 msec and 300 msec. Set it to the optimal
status.
 Depending on your TV, certain HDMI output
it supports the Anynet+ function.
System
Initial Settings
By using the Initial Settings, you can set
language, TV aspect, Musical Auto Calibration
and Network setting, etc.
For more information on the settings, refer to the
corresponding section in this user manual.
Internet@TV Screen Size
Set the Internet@TV Screen to the optimal size.
• Size 1 : Display smaller application icons, you
may see some black on sides of screen.
• Size 2 : Display normal application icons.
• Size 3 : Display larger application icons, image
may be too large for your TV screen.
resolutions may not work.
Please refer to the user manual of your TV.
 The Anynet+ function is supported only when
an HDMI Cable is connected to the HDMI OUT
of the product.
 If the HDMI cable or the power code is
unplugged, or if the product is turned off
abnormally due to power failure, first connect
the HDMI cable again; turn on all devices
including the product, and use the ANYNET+
function under the TV menu to activate all
connected devices again.
BD Data Management
Enables you to manage the downloaded contents from a
Blu-ray Disc that supports the BD-LIVE service.
You can check the device information including the
storage size, delete the BD data or change the Flash
memory device. Change Device allows you to select either
the product's Internal Memory or External Memory
(connected USB Device). If the data to be stored from
BD-LIVE is greater than the size of the remaining memory
or the Internal Memory is full, connect an External USB
device, then select External Device in the menu.
Settings
Anynet+(HDMI-CEC)
Anynet+ is a convenient function that offers linked
operations with other Samsung products with the
Anynet+ feature.
To operate this function, connect this product to
a Samsung TV with an HDMI cable.
Display
Audio
System
Network
Language
Security
General
Support
Menu :
BDOn-Screen
Data Management
Disc Menu: Internal Flash:Memory
Current Device
Total Size Audio
: 589MB
Subtitle : 589MB
Available Size
|
Delete BD Data
Change Device
> Move
:
:
: Internal Flash Memory
s Select
r Return
English
HT-C6950W_CIS_ENG_0409.indd 37
37
2010-04-09
10:56:16
Setup
Description of Device(Storage) Information on
the Product
DivX(R) Registration
• Total Size : Total size of the Device (Storage).
• Available Size : Available size of the Device (Storage).
View DivX(R) VOD Registration Code to purchase
and play DivX(R) VOD content.
✎ NOTE
 In the external memory mode, disc playback
will be stopped if you disconnect the USB
device in the middle of the playback.
 Only those USB devices formatted in FAT file
system (DOS 8.3 volume label) are supported,
and it is recommended to use USB devices
that support USB 2.0 protocol, 4 MB/sec or
faster read/write speed.
 The Resume Play function may not work after
formatting the storage device.
 The total size of BD Data Management may
differ, depending on the software version.
Clock
Set time-related functions.
Settings
Display
On-Screen
ClockMenu :
:
Audio Clock Mode Disc Menu
: Auto
|
System Clock Set
Audio
:
Network Time Zone Subtitle : GMT + 0:00:
LanguageDST
: Off
Security
General
> Move s Select r Return
Support
• Clock Mode : You can select Auto or Manual.
If you select Manual, the Clock Set menu will
be activated while DST will be deactivated.
• Clock Set : You can specify the current time
and date manually.
• Time Zone : You can specify the time zone
that is applicable to your area.
• DST : You can set DST (Daylight Saving Time)
1 hour, 2 hours and off.
38
Settings
Display
Audio
System
Network
Language
Security
General
Support
Initial Setting
Disc Menu
:
DivX(R)
AudioVideo On Demand:
Your registration
Subtitlecode is : XXXXXXXXXX
:
To learn more visit www.divx.com/vod
OK
✎ NOTE
 This option is not activated if you select OK.
To activate this option, please activate the
DivX(R) Deactivation.
DivX(R) Deactivation
Select this to get a new registration code.
Settings
Display
Audio
System
Network
Language
Security
General
Support
Initial Setting
Disc Menu
:
Audio
:
Subtitle
:
Do you want
to deactivate your device?
Yes
No
✎ NOTE
 This function can be operated when DivX(R)
Registration function is deactivated.
English
HT-C6950W_CIS_ENG_0419.indd 38
2010-04-19
4:41:50
03
Setup
Network Setup
Network Setting
To begin setting up the network connection for
your product, follow these steps:
1. In the Home menu, press the ◄► buttons to
select the Settings, and then press the
ENTER button.
Internet Protocol Setup
: Auto
IP Address
: 0
0
0
0
Subnet Mask
: 0
0
0
0
Gateway
: 0
0
0
0
DNS
: Auto
DNS Server
: 0
0
0
0
> Move
" Enter
' Return
2. Press the ▲▼ buttons to select Network,
and then press the ENTER button.
3. Press the ▲▼ buttons to select Network
Settings, and then press the ENTER button.
4. Press the ▲▼ buttons to select Network
Type, and then press the ENTER button.
Network Settings
Please contact your ISP to find out if your IP
address is static or dynamic. If it is dynamic, we
recommend using the Auto setting. This is the
easiest and will work in the majority of cases. If it is
static, you must use the manual set up procedure.
Wired Network
1. In the Network Settings menu, press the
▲▼ buttons to select Network Settings,
and then press the ENTER button.
The Internet Protocol Setup screen appears.
2. Press the ► button, then select Auto or
Manual, and then press the ENTER button.
Setting Up a Wired Connecton - Auto
1. If you selected Auto, the Network Function
acquires and fills in the values for IP Address,
Subnet Mask, etc., automatically.
✎ NOTE
 This process can take up to five minutes.
2. After the Network Function has acquired the
network values, press the RETURN button.
Then, run a Network Test to ensure the
product has connected to your network (See
page 40).
3. If the Network Function does not acquire the
network values or you selected Manual, go to
the directions for Manual Setup.
Setting Up a Wired Connecton - Manual
If the Auto Setting does not work, you’ll need to set
the Network Setting values manually.
To get the Network setting values from most
Windows computers, follow these steps:
1. Right click the Network icon on the bottom
right of the screen.
2. In the pop-up menu, click Status.
3. On the dialog that appears, click the Support
tab.
4. On the Support tab, click the Details button.
The Network settings are displayed.
To enter the Network settings into your product,
follow these steps:
1. On the Internet Protocol Setup screen, press
the ENTER button.
2. Press the ▲▼ buttons to select Manual,
and then press the ENTER button.
3. Press the ▼ button to go to the first entry
field (IP Address).
Network Setting
Internet Protocol Setup
: Manual
IP Address
: 0
Subnet Mask
: 255 255 255
0
Gateway
: 0
DNS
: Manual
DNS Server
: 0
> Move
" Enter
0
0
0
0
0
0
0
0
0
' Return
English
HT-C6950W_CIS_ENG_0407.indd 39
39
2010-04-08
6:26:32
Setup
4.
Use the number buttons on your remote to
enter numbers.
BD-LIVE Internet Connection
5.
When done with each field, use the ►
button to move successively to the next
field.
You can also use the other arrow buttons to
move up, down, and back.
6.
Enter the IP Address, Subnet Mask, and
Gateway values.
7.
Press the ▼ button to go to DNS.
Set whether to allow internet connection when
BD-LIVE service is used.
• Allow (All) : The Internet connection will be
allowed for all BD-LIVE contents.
• Allow (Valid Only) : The Internet connection
will be allowed only for BD-LIVE contents
containing a valid certificate.
• Prohibit : No Internet connection will be
allowed for any BD-LIVE content.
8.
Press the ▼ button to go to the first DNS
entry field.
9.
Press the RETURN button on your remote.
10. Run a Network Test to ensure the product
has connected to your network (See page
40).
Network Test
Use this menu to connect the wired network or
check whether your network connection is
working or not.
✎ NOTE
 What is a valid certificate?
When the product uses BD-LIVE to send the
disc data and request to the server to certify
the disc, the server uses the transferred data
to check if the disc is valid and sends the
certificate back to the product.
 The Internet connection may be restricted
while you are using BD-LIVE contents.
Language
Network Test
On-Screen Menu
:
MAC AddressDisc
(00:00:00:00:00:00)
Menu
:
IP Address,Subnet Mask,Gateway,DNS Server
Audio
:
Gateway Ping
Subtitle
Internet Service Test
:
The network configuration (IP) is not valid. Check the
network settings and enter a valid value before trying
again.
r Return
Network Status
Check whether a connection to the network and
the Internet have been established.
40
You can select the language you prefer for home
menu, disc menu, etc.
• On-Screen Menu : Select the language for the
on-screen displays.
• Disc Menu : Select the language for the disc
menu displays.
• Audio : Select the language for disc audio.
• Subtitle : Select the language for disc subtitles.
✎ NOTE
 The selected language will only appear if it is
supported on the disc.
English
HT-C6950W_CIS_ENG_0407.indd 40
2010-04-08
6:26:33
03
General
When you operate this menu for the first time,
password setup screen will be displayed. Enter
the desired 4-digit password using the number
buttons. (Default password is set to 0000.)
Parental Rating
Background
Change the background theme of the menu screen.
Settings
This function works in conjunction with Blu-ray
Disc/DVDs that have been assigned a rating,
which helps you control the types of Blu-ray Disc/
DVDs that your family watches.
Select the rating level you want to set. A larger
number indicates that the program is intended for
adult use only. For example, if you select up to
Level 6, discs that contain Level 7, 8 will not play.
Settings
Display
Audio
System
Network
Language
Security
General
Support
Setup
Security
Display
Audio
System
Network
Language
Security
General
Support
Background
Parental Rating
: Off
Change Password
Skin 1
Skin 2
Skin 3
Skin 4
Skin 5
> Move
s Select
r Return
Front Display
Parental Rating
Change Password
Off
8(Adults)
7
6
5
4
3
2
Change the brightness of the front panel.
• Auto : Dim during playback only.
• Dim : Dim the display window.
• Bright : Brighten the display window.
▼
Power On/Off Sound
Change Password
Change the 4-digit password used to access
security functions.
Settings
Change Password
Display
Audio
System
Enter the password
Network
Language
Security
General
Enter Pin r Return
Support
Play a melody when the product is turned on and
off.
• Off : Turn Power Sound Off.
• On : Turn Power Sound On.
Light Effect
You can activate or deactivate the light effect on the
top of the product.
• Always On : Activate Light Effect at all times.
Select this for retail display.
• Auto : Activate Light Effect when turning the
product on and off or when moving the tray.
Select when installing the product in your home.
• Off : Turn Light Effect off at all times.
If you forgot your password
1. Remove the disc.
2. Press and hold the STOP () button on the
front panel for 5 seconds or more.
All settings will revert to the factory settings.
✎ NOTE
 When the factory default settings are restored, all the
user data stored in the BD data will be deleted.
English
HT-C6950W_CIS_ENG_0407.indd 41
41
2010-04-08
6:26:33
Setup
Support
Software Upgrade
This menu allows you to upgrade software for
performance improvements or additional services.
You can check the current software version,
upgrade by internet and set the Auto upgrade
notification.
Settings
Display
Software Upgrade
Software
Disc MenuUpgrade :
Audio
:
System Current Version Audio : XXX-XXXXXXXXX
Subtitle
:
NetworkBy Internet
|
Language
Auto Upgrade Notification : On
Security
General
> Move s Select r Return
Support
You can update software in any of the two ways
as follows: Software update is the same as in the
By Internet menu.
• USB : Visit www.samsung.com/bluraysupport,
then download and store the latest software
(RUF file) into the USB flash drive. Connect the
USB flash drive to the USB port of the product
(disc tray must be empty) to update the
software, then follow the on-screen
instructions.
• CD : Visit www.samsung.com/bluraysupport,
download and write the latest software (RUF
file) onto a disc. Insert and play the disc in the
product to start the update, then follow the onscreen instructions.
✎ NOTE
 Software upgrades using the USB Host jack
must be performed with no disc inside.
1. To select By Internet, press the ENTER
button.
A popup message will appear if an update is
available.
2. If you select Yes, the product will turn off
automatically before restarting.
(Never turn it on manually.)
3. The update progress popup will appear.
When the update is completed, the product
will turn back off automatically.
4. Press the POWER button to turn on the
product.
✎ NOTE
 The Update will be completed when the
product turns off after restarting. Press the
POWER button to turn on the updated product
for your use. Never turn off or on the product
manually during the update process.
 Samsung Electronics shall take no legal
responsibility for product malfunction caused an
unstable internet connection or consumer
negligence during software upgrade.
42
 If you want to cancel the upgrade in the
process of downloading the upgrade data,
press the ENTER button.
 When the system upgrade is done, check the
software details in the software Upgrade
menu.
 Do not turn off the product during the System
Upgrade, as it may cause the product to not
work properly.
 Do not use USB devices other than USB Flash
Drives to do software upgrades when using
the USB Host jack.
Contact Samsung
Provide contact information for assistance with
your product.
English
HT-C6950W_CIS_ENG_0407.indd 42
2010-04-08
6:26:36
Disc Structure
The contents of disc are usually divided as below.
Playback
• Blu-ray Disc, DVD-VIDEO
1. Press the OPEN/CLOSE ( ) button to open
the disc tray.
2. Place a disc gently into the tray with the
disc’s label facing up.
3. Press the PLAY (►) button or OPEN/
CLOSE ( ) button to close the disc tray.
Playback related buttons
PLAY ( ►)
STOP (  )
chapter 1
title 2
chapter 2
chapter 3
track 3
track 4
track 5
• Audio CD (CD-DA)
track 1
track 2
• MP3, WMA, DivX, MKV and MP4
folder (group) 1
file 1
file 2
file 1
folder (group) 2
file 2
file 3
Starts playback.
Stops playback.
• If pressing the button once:
The stop position will be
memorized.
• If pressing the button twice:
The stop position will be not
memorized.
(With some Blu-ray discs (BD-J),
this function may not work.)
PAUSE (  )
title 1
chapter 1 chapter 2
Basic Functions
Playing a Disc
04
Basic Functions
Pauses playback.
✎ NOTE
 "Not Available" will appear when an invalid
Using the Disc menu / Title menu / Popup menu
Using the Disc Menu
hZ
1. During playback, press the DISC
MENU button on the remote
control.
2. Press the ▲▼◄ ► buttons to make
the desired selection, then press the
ENTER button.
DISC MENU
✎ NOTE
 Depending on the disc, the menu items may
differ and this menu may not be available.
button is pressed.
English
HT-C6950W_CIS_ENG_0407.indd 43
43
2010-04-08
6:26:36
Basic Functions
Using the Title Menu
Using the Search and Skip Functions
Z
1. During playback, press the TITLE
MENU button on the remote
control.
2. Press the ▲▼◄ ► buttons to
make the desired selection, then
press the ENTER button.
TITLE MENU
POPUP
Searching for a Desired Scene
hzZyx
✎ NOTE
 Depending on the disc, the menu items may
differ and this menu may not be available.
 The Title Menu will only be displayed if there
are at least two titles on the disc.
Playing the Title List
z
1. During playback, press the DISC
MENU or TITLE MENU button.
2. Press the ▲▼ buttons to select an
entry you want to play from Title
List, then press the ENTER
button.
DISC MENU
TITLE MENU
POPUP
BD-ROM,
BD-RE/-R,
DVD-RW/-R,
DVD+RW/+R,
DVD-VIDEO
)1
)4
(1
(4
)2
)5
(2
(5
)3
)6
(3
(6
DivX, MKV, MP4
)1
(1
)2
(2
)3
(3
)7
(7
• To return to normal speed playback, press the
PLAY (►) button.
 No sound is heard during search mode.
h
TITLE MENU
POPUP
2. Press the ▲▼◄ ► buttons or
ENTER button to select the desired
menu.
✎ NOTE
 Depending on the disc, the menu items may
differ and this menu may not be available.
44
• During playback, press the SEARCH ()
button.
Each time you press the SEARCH ()
button, the playback speed will change as
follows.
✎ NOTE
Using the Popup Menu
1. During playback, press the POPUP
button on the remote control.
During playback, you can search quickly through
a chapter or track, and use the skip function to
jump to the next selection.
Skipping Chapters
hzZyx
• During playback, press the SKIP (#$)
button.
If you press the SKIP ($) button, it moves to
the next chapter.
If you press the SKIP (#) button, it moves to
the beginning of the chapter. One more press
makes it move to the beginning of the previous
chapter.
English
HT-C6950W_CIS_ENG_0407.indd 44
2010-04-08
6:26:37
04
Basic Functions
Slow Motion Play/Step Motion Play
Repeat
Off
Slow Motion Play
hzZyx
• In pause mode, press the SEARCH ()
button.
If you press the SEARCH () button, the
playback speed is reduced to
* 1/8 * 1/4 * 1/2
• To return to normal speed playback, press the
PLAY (► ) button.
✎ NOTE
3. To return to normal play, press the REPEAT
button again.
4. Press the ▲▼ buttons to select Off, the
press the ENTER button.
✎ NOTE
 Depending on the disc, the Repeat function
may not be available.
Repeat the Section
 No sound is heard during slow mode.
 Slow motion operates only in the forward
hzZy
direction.
 Slow motion can not operate on DivX discs.
Step Motion Play
hzZyx
• In pause mode, press the PAUSE (  ) button.
Each time the PAUSE (  ) button is pressed, a
new frame will be appear.
• To return to normal speed playback, press the
PLAY ( ► ) button.
✎
NOTE
 No sound is heard during step mode.
 Step motion operates only in the forward
direction.
 Step motion can not operate on DivX discs.
1. During playback, press the REPEAT
button on the remote control.
REPEAT
2. Press the ▲▼ buttons to select
REPEAT A-B.
Repeat
REPEAT A-B : Off
s Mark A
3. Press the ENTER button at the point where
you want repeat play to start (A).
4. Press the ENTER button at the point where
you want repeat play to stop (B).
5. To return to normal play, press the REPEAT
button again.
6. Press the ENTER button.
Repeat Playback
✎ NOTE
Repeat the Title or Chapter
 If you set point (B) before 5 seconds has
hzZy
lapsed, the prohibition message will appear.
Repeat the disc title or chapter.
1. During playback, press the REPEAT
button on the remote control.
REPEAT
2. Press the ▲▼ buttons to select
Chapter or Title, then press the
ENTER button.
English
HT-C6950W_CIS_ENG_0407.indd 45
45
2010-04-08
6:26:38
Basic Functions
 Information about the primary / secondary
Using the TOOLS button
During playback, you can operate disc
menu by pressing the TOOLS button.
TOOLS
• TOOLS Menu Screen
Tools
Title
:
1/1
Chapter
4/21
Playing Time
:
00:12:06
Repeat
Audio
: 1/7 ENG Multi CH
Subtitle
:
1/6 ENG
Angle
:
1/1
BONUSVIEW Video :
Off
BONUSVIEW Audio :
0/1 Off
mode will be also displayed if the Blu-ray Disc
has a BONUSVIEW section.
Use the ◄► button to switch between
primary and secondary audio modes.
 This function depends on what audio
languages are encoded on the disc and may
not be available.
 A Blu-ray Disc can contain up to 32 audio
languages and a DVD up to 8.
 Some Blu-ray Discs may allow you to select
either the multi-channel LPCM or Dolby digital
audio soundtrack in English.
Picture Setting
< Change " Select
Selecting the Subtitle Language
✎ NOTE
▪ Depending on the disc, the TOOLS menu may
differ.
hZx
1. During playback, press the TOOLS button.
2. Press the ▲▼ buttons to select Subtitle.
Moving to a Desired Scene Directly
3. Press the ◄► buttons to select the desired
subtitle language.
hzZy ✎ NOTE
1. During playback, press the TOOLS button.
 Depending on the Blu-ray Disc / DVD, you may
2. Press the ▲▼ buttons to select Title,
Chapter or Playing Time.
3. Enter the desired Title, Chapter or Playing
Time using the number buttons, then press
the ENTER button.

Selecting the Audio Language

hzZx
1. During playback, press the TOOLS button.

2. Press the ▲▼ buttons to select Audio.

3. Press the ◄► buttons to select the desired
audio language.

be able to change the desired subtitle in the
Disc Menu.
Press the DISC MENU button.
This function depends on what subtitles are
encoded on the disc and may not be available
on all Blu-ray Discs/DVDs.
A Blu-ray Disc can contain up to 255 subtitle
languages and a DVD up to 32.
Information about the primary / secondary
mode will also be displayed if the Blu-ray Disc
has a BONUSVIEW section.
This function changes both the primary and
secondary subtitles at the same time.
The total number of subtitles is the sum of the
primary and secondary ones.
✎ NOTE
 The ◄► indicator will not be displayed on the
screen if the BONUSVIEW section does not
contain any BONUSVIEW audio settings.
46
English
HT-C6950W_CIS_ENG_0407.indd 46
2010-04-08
6:26:41
04
x
• You must have some experience with video
extraction and editing in order to use this
feature properly.
• To use the caption function, save the caption
file (*.smi) in the same file name as that of the
DivX media file (*.avi) within the same folder.
Example. Root Samsung_007CD1.avi
Samsung_007CD1.smi
• Up to 60 alphanumeric characters or 30 East Asian
characters (2 byte characters such as Korean and
Chinese) for the file name.
• User : The user can adjust the sharpness
and noise reduction function respectively.
Setting the BONUSVIEW
Basic Functions
Caption Function
h
The BONUSVIEW feature allows you to view
additional content (such as commentaries) in a
small screen window while the movie is playing.
This function is only available if the disc has the
bonusview feature.
Changing the Camera Angle
hZ
When a Blu-ray Disc/DVD contains multiple
angles of a particular scene, you can use the
ANGLE function.
1. During playback, press the TOOLS button.
Primary a audio/video
Secondary a audio/video
2. Press the ▲▼ buttons to select Angle.
3. Press the ◄► buttons to select the desired
Angle.
1. During playback, press the TOOLS button.
Selecting the Picture Setting
3. Press the ◄► buttons to select the desired
bonusview.
2. Press the ▲▼ buttons to select BONUSVIEW
Video or BONUSVIEW Audio.
hzZy ✎ NOTE
This function enables you to adjust video quality
when you are connected to a TV via HDMI.
1. During playback, press the TOOLS button.
2. Press the ▲▼ buttons to select Picture
Setting, then press the ENTER button.
3. Press the ◄► buttons to select the desired
Picture Setting, then press the ENTER
button.
• Dynamic : Choose this setting to increase
Sharpness.
• Normal : Choose this setting for most
viewing applications.
• Movie : This is the best setting for watching
movies.
 If you switch from BONUSVIEW Video,
BONUSVIEW Audio will change automatically
in accordance with BONUSVIEW Video.
Tools
BONUSVIEW Video
Off
BONUSVIEW Audio :
0/1 Off
Picture Setting
< Change " Select
English
HT-C6950W_CIS_ENG_0407.indd 47
47
2010-04-08
6:26:44
Basic Functions
Listening to Music
ow
Buttons on the Remote Control
used for Music Playback
@
1
2
3
4
5
6
7
8
9
FULL SCREEN
ENTER button : Plays and pauses the selected
track.
8
◄► buttons : Fast Play.
(except for Audio CD (CD-DA))
9
STOP button : Stops a track.
0
SKIP($) button : During playback, moves to
the next page in the Music List or moves to the
next track in the Playlist.
!
SKIP (#)button : During playback, moves to the
previous page in the Music List or moves to the
previous track in the Playlist.
If you press this button after three seconds of
playback in the Playlist, the current track will be
replayed from the beginning. But, if you press this
button within three seconds after playback starts
in the Playlist, the previous track will be played.
@
NUMBER button : During the Playlist playback,
press the desired track number. The selected
track will be played.
REPEAT
0
!
1
2
0
3
9
8
7
4
TOOLS
INFO
5
7
RETURN
EXIT
TUNER
MEMORY
A
B
C
INTERNET@
MO/ST
D
6
DSP
1
REPEAT buttons : Selects the play mode in the
Playlist.
2
SEARCH buttons : Fast Play.
(Audio CD (CD-DA) only)
3
PAUSE button : Pauses playback.
4
PLAY button : Plays the currently selected track.
5
▲▼ buttons : Selects a track in the Music List
or Playlist.
6
YELLOW(C) button : Select or deselect a track
in the music list.
48
English
HT-C6950W_CIS_ENG_0407.indd 48
2010-04-08
6:26:44
04
Repeat an Audio CD (CD-DA)/MP3
1. Insert an Audio CD (CD-DA) or an MP3 Disc
into the disc tray.
• For an Audio CD (CD-DA), the first track will
be played automatically.
• For an MP3 disc, press the ◄► buttons to
select Music, then press the ENTER
button.
1. During the Playlist playback, press
the REPEAT button.
2. Select the desired play mode by pressing
the REPEAT button repeatedly.
Off
Tracks on a disc are played
Audio CD
in the order in which they
(CD-DA)/MP3
were recorded on the disc.
(
) Track
Audio CD
(CD-DA)
Current track is repeated.
(
) One
MP3
Current track is repeated.
(
) All
Audio CD
All tracks are repeated.
(CD-DA)/MP3
(
) Shuffle
Audio CD
The random option plays a
(CD-DA)/MP3 disc's track in random order.
Audio CD (CD-DA)/MP3 Screen Elements
1
2
3
Playlist
TRACK 001
1/12
TRACK 001
05:57
REPEAT
TRACK 002
Basic Functions
Playing an Audio CD (CD-DA)/MP3
04:27
TRACK 003
7
6
04:07
TRACK 004
+
03:41
00:08 / 05:57
TRACK 005
03:17
TRACK 006
03:35
s Pause
5
Tools
Playlist
r Return
4
1
Displays the music information.
2
Displays the playlist.
3
Shows the current track/total tracks.
4
Displays buttons available.
5
Shows the current play time/total play time.
6
Displays the current playback status.
7
Displays the repeated playback status.
1. Insert an Audio CD (CD-DA) or an MP3 Disc
into the disc tray.
• For an Audio CD (CD-DA), the first track will
be played automatically.
• For an MP3 disc, press the ◄► buttons to
select Music, then press the ENTER button.
2. To move to the Music List, press the STOP ()
or RETURN button.
The Music List screen is displayed.
3. Press the ▲▼◄► buttons to move to the
desired track, then press the YELLOW(C) button
to check desired tracks.
Repeat this procedure to select additional tracks.
Music
2. Press the ▲▼ buttons to select the track
you want to play, and then press the ENTER
button.
TRACK 001
TRACK 002
00:05:57
00:04:27
TRACK 003
TRACK 004
00:04:07
00:03:41
TRACK 005
TRACK 006
00:03:17
00:03:35
TRACK 007
TRACK 008
00:03:47
00:03:49
TRACK 009
00:03:53
CDDA
3 files selected 1/2 Page
TRACK 003
TRACK 010
00:03:45
Select
 Jump page
r Return
English
HT-C6950W_CIS_ENG_0407.indd 49
49
2010-04-08
6:26:45
Basic Functions
4. If there is an undesired track in the playlist,
press the YELLOW(C) button again.
The selected track will be deleted.
5. Press the ENTER button to play the selected
tracks.
The selected track will automatically play.
1/1
Playlist
TRACK 001
+
TRACK 001
05:57
TRACK 002
04:27
TRACK 003
04:07
Sound Mode
DSP(Digital Signal Processor) Function
This will regulate and stabilize the volume level
against a drastic volume change when changing
channels or during a scene transition.
Press the DSP button.
DSP
SMART SOUND MP3 ENHANCER POWER BASS DSP MODE OFF
00:08 / 05:57
s Pause
Tools
r Return
6. To go to the Music List, press the STOP ()
or RETURN button.
7. To go to the Playlist, press the ENTER
button.
✎ NOTE
 You can create a playlist with up to 99 tracks
on Audio CD (CD-DA).
• SMART SOUND : This will regulate and
stabilize the volume level against a drastic
volume change when changing channels or
during a scene transition.
• MP3 ENHANCER : This also helps enhance
your sound experience (ex. mp3 music). You
can upscale your MP3 level sound(24 kHz,
8bit) to CD level sound(44.1 kHz, 16bit).
• POWER BASS : This function stresses low
tones providing thudding sound effects.
SFE(Sound Field Effect) MODE
You can set the SFE mode best suited for the
type of music you are listening to.
SFE MODE
Press the SFE MODE button.
HALL1
Provides a clear vocal as if
listening in a concert hall.
HALL2
Provides also a clear vocal as if
listening in a concert hall but, less
powerful than HALL1.
JAZZ
Recommended setting for Jazz.
CHURCH
Gives the feel of being in a grand
church.
ROCK
Recommended setting for Rock.
SFE OFF
50
Select this for normal listening.
English
HT-C6950W_CIS_ENG_0407.indd 50
2010-04-08
6:26:47
04
Using the TOOLS button
You can select the desired Dolby Pro
Logic II audio mode.
During the slide show playback, you
can use various function by pressing
the TOOLS button.
Press the
MUSIC
MOVIE
PL II button.
When listening to music, you can experience
sound effects as if you are listening to the
actual performance.
TOOLS
Basic Functions
Dolby Pro Logic II Mode
Tools
Stop Slide Show
Slide Show Speed :
Normal
Slide Show Effect :
Fade1
Background Music
Adds realism to the movie soundtrack.
Zoom
PROLOG
You will experience a realistic multi-channel
effect, as if using six speakers, while using
just the front left and right speakers.
MATRIX
You will hear multi channel surround sound.
STEREO
Select this to listen to sound from the front left
and right speakers and the subwoofer only.
✎ NOTE
 When selecting Dolby Pro Logic II mode,
connect your external device to the AUDIO
INPUT jacks (L and R) on the product. If you
connect to only one of the inputs (L or R), you
cannot listen to surround sound.
 This mode is available with both 2 channel
and 5.1 channel audio. 7.1ch audio is directly
transmitted without any transformation.
Playing back a Picture
G
Playing a JPEG Disc
1. Insert a JPEG disc into the disc tray.
2. Press the ◄► buttons to select the Photos,
and then press the ENTER button.
3. Press the ▲▼◄► buttons to select the
folder you want to play, and then press the
ENTER button.
Rotate
Information
> Move
" Enter
' Return
• Stop Slide Show : Select this if you want to
stop the slide show.
• Slide Show Speed : Select this if you want to
adjust the Slide Show speed.
• Slide Show Effect : Select if you want to set
the Slide Show Effect.
• Background Music : Select this if you want to
listen to music while viewing a picture.
• Zoom : Select this if you want to enlarge the
current picture. (Enlarged up to 4 times)
• Rotate : Select this if you to rotate the picture.
(This will rotate the picture either clockwise or
counter clockwise.)
• Information : Shows the picture information
including the name and size, etc.
✎ NOTE
 To enable the Background Music function,
both music and MP3 files must be contained in
the same folder. However, the sound quality
can be affected by the bit rate of the MP3 file,
the size of the photo and the encoding
method.
4. Press the ▲▼◄► buttons to select the
photo you want to play, and then press the
ENTER button.
✎ NOTE
 You can't enlarge the subtitle and PG graphic
in the full screen mode.
English
HT-C6950W_CIS_ENG_0407.indd 51
51
2010-04-08
6:26:49
Basic Functions
✎ NOTE
Playing back a USB Storage
F
You can use the USB connection to play multimedia
files (MP3, JPEG, DivX, etc) downloaded from the
USB storage device.
1. Move to the home menu.
2. In Stop mode, connect the USB storage device to
the USB port on the front panel of the product.
The message “Do you want to access the
device?” will be displayed.
3. Press the ◄► button to select Yes, then
press the ENTER button.
4. Press the RED(A) button.
You Tube
internet radio service
Please activate Internet@TV
to enjoy a variety of Internet Services.
 You must remove the USB storage device
safely (by performing the “Safe to Remove
Hardware” function) in order to prevent a
possible damage to the USB memory. Press
the MENU button to move to the main screen,
and select the YELLOW(C) button and press the
ENTER button.
 When the Audio-CD (CD-DA), MP3 and JPEG
files are in stop mode, you can't see full screen
by pressing the FULL SCREEN button on the
remote control.
 If you insert the disc when playing USB a
storage device, the device mode is changed to
“DVD or CD” automatically.
 To listen to your music files with 7.1 channel sound,
you must set the Dolby Pro Logic ll mode to Matrix.
(See page 51)
CD
USB
USB a Change Device Safely Remove USB d View Devices " Enter
5.
Press the ▲▼ buttons to select the USB,
then press the ENTER button.
6. Press the ◄► buttons to select the desired Videos,
Music or Photos, then press the ENTER button.
4-1. Press the BLUE(D) button.
Please activate Internet@TV service
to enjoy a variety of Internet Services.
USB
USB
d Home
" Enter
5-1. Press the ◄► buttons to select the USB,
then press the ENTER button.
6-1. Press the ▲▼ buttons to select the desired
Videos, Music or Photos, then press the
ENTER button.
7. For playing back Video, Music or Photos
files, see pages 43~51.
52
English
HT-C6950W_CIS_ENG_0409.indd 52
2010-04-09
10:58:45
04
Using buttons on the Remote Control
1. Press the FUNCTION button to select FM.
2. Tune in to the desired station.
• Automatic Tuning 1 : When the # $ button
is pressed, a preset broadcast station is selected.
• Automatic Tuning 2 : Press and hold the
) button to automatically
TUNING/CH (
search for active broadcasting stations.
• Manual Tuning : Press the TUNING/CH
(
) button to increase or decrease the
frequency incrementally.
Using buttons on the product
1. Press the FUNCTION (
) button to select FM.
2. Select a broadcast station.
• Automatic Tuning 1 : Press the STOP ( )
button to select PRESET and then press the
# $ button to select the preset station.
• Automatic Tuning 2 : Press the STOP ( )
button to select MANUAL and then press and
hold the # $ button to automatically
search the band.
• Manual Tuning : Press the STOP ( ) button to
select MANUAL and then press the # $
button to tune in to a lower or higher frequency.
Setting Mono/Stereo
MO/ST
Press the MO/ST button.
D
• Each time the button is pressed, the
sound switches between STEREO
and MONO.
• In a poor reception area, select MONO for a
clear, interference-free broadcast.
Presetting Stations
Example : Presetting FM 89.10 into memory
1. Press the FUNCTION button to select FM.
) button to select
2. Press the TUNING/CH (
<89.10>.
TUNER
3. Press the TUNER MEMORY button. MEMORY
C
• NUMBER flashes on the display.
4. Press the # $ button to select
preset number.
• You can select between 1 and 15
presets.
5. Press the TUNER MEMORY button again.
• Press the TUNER MEMORY button before
NUMBER disappears from the display.
• NUMBER disappears from the display and
the station is stored in memory.
6. To preset another station, repeat steps 2 to 5.
• To tune in to a preset station, press the # $
button on the remote control to select a channel.
English
HT-C6950W_CIS_ENG_0407.indd 53
Basic Functions
Listening to Radio
53
2010-04-08
6:26:54
Network Services
You can enjoy various network services such as
Internet@TV or BD-LIVE by connecting the
product to the network system.
Check the following instructions before using
any network service.
4. After you have signed off on the service
agreement, the Internet@TV service starts
updating. It takes several minutes. When the
update is complete, you will see the
Internet@TV menu screen.
1. Connect the product to the network.
(see page 26)
Internet@TV at a Glance
2. Configure the network settings.
(see pages 39~40)
1
2
3
Recommended
Contents 1
Using Internet@TV
Contents 2
Contents 3
My Applications
Contents 1
Connect this product to the network to download
various for a fee or free-of-charge applications.
Internet@TV brings useful and entertaining
content and services directly from the web to
your product such as news, weather forecasts,
stock market quotes, games, movies and music.
Contents 2
Contents 4
by Date 1/3
Contents 3
Samsung AppS Settings
a Login
6
5
b Mark as Favorite
d Sort by ' Return
4
INTERNET@
You can also initiate this function by
pressing the INTERNET@ button
on the remote control.
Getting Started with Internet@TV
1. Move to the home menu.
1
Commercial : Displays Internet@TV Guide,
product introduction and new application
introduction.
2
Recommended : Displays recommended
contents managed by Samsung.
3
My Application : Displays your personal gallery
which can be added and deleted by you.
4
Navigation Help : Displays remote control
buttons available.
• RED(A) : To log in to to Internet@TV.
• GREEN(B) : To mark the application as
a favourite.
• BLUE(D) : To sort the applications.
• Return : To return to the previous
menu.
5
Settings : You can set the system setup and
create accounts, etc.
6
Samsung AppS : You can download various
chargeable or free-of-charge application services.
You Tube
internet radio service
Please activate Internet@TV
to enjoy a variety of Internet Services.
No Disc
a Change Device
d View Devices
" Enter
2. Press the ◄► buttons to select Internet@
TV and press the ENTER button.
3. In the start screen of the Internet@TV service, you
will see the service agreement screen.
You must agree to the service terms and
conditions before you can use the Internet@TV
service.
54
English
HT-C6950W_CIS_ENG_0407.indd 54
2010-04-08
6:26:55
05
13. Press the ENTER button.
Through your remote, you can use the
On-Screen Keypad in several Internet@TV
applications to enter text.
Pressing the FULL SCREEN button on the
remote while you are using the Screen Keypad
lets you to change the text fields to lower case,
upper case, numbers and icons.
14. The map and address appear on the screen.
✎ NOTE
 Samsung Electronics shall take no legal
Network Services
Using the Keypad
responsibility for any interruption of the
Internet@TV service caused by the service
provider for any reasons.
 The Internet@TV service is to download and
1
2
abc
3
def
4
ghi
5
jkl
6
mno
7
pqrs
8
tuv
9
wxyz
a
]
0
Input Mode
A
Delete
1
For example, here is how to search an address in
Google Maps:
process data via the Internet so that you can
enjoy the contents on the TV screen.
If the Internet connection is unstable, the
service may be delayed or interrupted.
Furthermore, the product may be turned off
automatically.
If this is the case, check the Internet
connection and try again.
 The application service may be provided in
English only and the contents available may
vary, depending on the area.
1.
Press the ENTER button on the remote at
the Google Maps icon at the Internet@TV.
2.
Press the GREEN(B) button to use the
SEARCH function.
service, visit the web site of the applicable
service provider.
3.
Press the ◄► buttons to move to the
"Search or address" window.
 The services provided are subject to change,
4.
Press the ENTER button to use Search or
address function.
5.
For example, suppose that you want to input
“105 Challenger Rd., Ridgefield Park NJ’.
6.
Press the FULL SCREEN button on the
remote twice to change the input mode from
lower case to numbers.
7.
Press ‘1’, ‘0’, ‘5’.
8.
Press the YELLOW(C) button on the remote
to input a blank space.
9.
Press the FULL SCREEN button on the
remote 3 times to change the input mode
from numbers to upper case.
 For more information about the Internet@TV
depending on the Internet@TV service
provider.
 The Internet@TV service contents may differ
according to the firmware version.
 For-a-fee DivX contents with copy protection
can only be played using HDMI cable.
If you have connected your player to your TV
using Component or video cables, the DivX
video signal can not output or the popup
message “Connect with a HDMI cable to play
this file.”or “Cannot play current file” will be
displayed.
10. Press ‘2’ button on the remote 3 times to
input C.
11. Press the FULL SCREEN button on the
remote 3 times to change the input mode
from upper case to lower case.
12. Press buttons on the remote to input the rest
of ‘Challenger Rd., Ridgefield Park NJ’.
English
HT-C6950W_CIS_ENG_0407.indd 55
55
2010-04-08
6:26:57
Network Services
Account Login
System Setup
For a more enjoyable application experience,
register and log in to your account.
Reset
To do this, you must create an account first. (For
instructions on creating an account, refer to
Internet@TV ID on this page)
1.
Press the ▲▼◄► buttons to select the
desired application and press the RED(A)
button.
Resets Internet@TV settings to factory default
settings.
✎ NOTE
 If you forgot your password, press the STOP
() button on the front panel of the product for
more than 5 seconds with no disc inserted.
Login
Internet@TV ID
User Account :
Use this menu to create or delete an account and
enter or delete account information.
adgim
Password :
You can control your account including contents
site’s account information.
a Create
[0~9] Enter PIN ' Cancel
This account is only for Internet@TV.
Create
2.
Enter the user account and password.
✎ NOTE
Settings
Create IDs and configure Internet@TV settings
from this screen.
character in length but no more than 8.
Names.
Change the Service Lock password
Reset
' Cancel
56
 The account name must be at least 1
 You can register up to 10 User Account
Settings
System setup
Internet@TV ID
Service Manager
Properties
Create an account and link it with desired service
applications.
Manager
• Service Site : Register login information for
service sites.
• Change Password : Change account
password.
• Delete : Delete the account.
English
HT-C6950W_CIS_ENG_0407.indd 56
2010-04-08
6:26:58
05
Delete and lock applications installed to Internet@
TV.
Lock
Lock the application. Accessing a locked
application requires the password.
Using the colour buttons with the Samsung
Apps
• RED(A) (Login) : To log in to the internet
service.
• GREEN(B) (Thumbnail View) : To change the
view mode.
• BLUE(D) (Sort By) : To sort the applications
by Featured, Most Downloaded, Most Recent
or Name.
Network Services
Service Manager
Delete
Delete the application.
Internet@TV Services Available
Properties
- YouTube : You can view video streamed by
YouTube.
Display information about Internet@TV. Use the
Check the speed of your internet connection
option to test your network connection.
✎ NOTE
 The available Internet contents service may be
added or deleted.
Samsung AppS
Various applications are available from here,
organized into different categories. Some
applications have a download fee.
Samsung AppS
What's New!
| Video
| Sports
| Lifestyle
| Games
| Infomation
| Other
|
Video
Featured
1/1
Most downloaded
Most recent
YouTube
Name
Free
TV store Test User002
My Applications
Help
a Login
b Thumbnail View
d Sort By
' Return
My Application
Displays the application list.
Help
If you questions about Internet@TV, check this
section first. If none of the tips apply, please visit
the help website.
English
HT-C6950W_CIS_ENG_0407.indd 57
57
2010-04-08
6:26:58
Network Services
Using the AllShare Function
BD-LIVE™
Once the product is connected to the network,
you can enjoy various movie-related service
contents using a BD-LIVE compliant disc.
1. Check the size of the remaining memory.
The memory device must have at least 1GB
of free space to accommodate the BD-LIVE
services.
2. Insert a Blu-ray disc that supports BD-LIVE.
3. Select an item from various BD-LIVE service
contents provided by the disc manufacturer.
✎ NOTE
 The way you use BD-LIVE and the provided
contents may differ, depending on the disc
manufacturer.
Software Upgrade Notification
In network connection, the product will notice you of
any new software version with a popup message.
1. Turn on the product.
2. From the Software Upgrade menu, set Auto
Upgrade Notification to On. (See page 42)
If there is a new software version available,
the product will notice you with a popup
message.
3. To upgrade the firmware, select Yes.
It will turn off automatically before restarting.
(Never turn it on manually.)
4. The update progress popup will appear.
When the update is completed, it will turn
back off automatically.
AllShare enables you to play music, video and
photo files in your PC using the product.
To use AllShare, you must connect the product
to your PC via the network (See page 26) and
install the SAMSUNG PC Share Manager on the
PC.
1. Visit the Samsung website at www.samsung.
com.
2. Download the SAMSUNG PC Share
Manager and install it on the PC.
3. When the installation is completed, you will
see the SAMSUNG PC Share Manager icon
on your desktop.
Double-click the icon to launch the
application.
4. Select a folder to share from the My
computer pane, and click the Share Folder
Enabled icon ( ).
(To remove a shared folder : Select a folder
to remove from the shared folders, and click
the Share Folder Disabled icon ( ).)
5. To apply the updated sharing state to the
server, click the Set Change State icon (
SAMSUNG PC Share Manager
File
Share
Server
Help
Server : PC Share Manager
Set Device Policy
My Computer
Shared Folder
C: Document and settings Admin
IP
Device
Name
Size
Kind
SAMSUNG Blu-ray
FolderXXX.XXX.X.XX
1
FileDisc Player
Folder 2
Folder 3
5. Press the POWER button to turn on the
product.
).
6. To enable the product to locate a PC server,
click Share from the menu bar.
Click Set Device Policy and click Accept.
Folder
State
Folder 1
Deny
Delete Selected Item
Full Path
Set State
C: Document and settin..
Accept
File
File
OK
Cancel
✎ NOTE
 Update will be completed when the product
turns off after restarting. Press the POWER
button to turn on the updated product for your
use.
Never turn off or on the product manually
during the update process.
 Samsung Electronics shall take no legal
responsibility for product malfunction caused by
unstable of internet connection or consumer
negligence during software upgrade.
58
7. Click the Set Change State icon ( ) and
move to the home menu on the product.
English
HT-C6950W_CIS_ENG_0407.indd 58
2010-04-08
6:26:58
05
Application Program at a Glance
6
1
SAMSUNG PC Share Manager
File
Share
Server
Help
Server : PC Share Manager
2345
My Computer
a Change Device
d View Devices
Shared Folder
C: Document and settings Admin
You Tube
internet radio service
Please activate Internet@TV
to enjoy a variety of Internet Services.
No Disc
Name
Folder 1
" Enter
✎ NOTE
 Depending on te performance of the external
modem or router, HD video may not play
properly.
 If your system uses a firewall, the product may
 The Sorting method may differ depending on
the sever function.
Kind
File
Folder 2
File
Folder 3
File
Folder
Folder 1
Full Path
C: Document and settin..
7
1
Menu Bar
2
Share Folder Enabled icon : Use this if you
want to select a folder in your PC to share.
3
Share Folder Disabled icon : Use this if you
want to set folder sharing off.
4
Refresh icon : Use this if you want to refresh
list of folders and files in My Computer.
5
Set Change State icon : Select a folder to
share and don’t forget to press this button.
The updated state will be applied to the server.
6
Server : Displays the name of the sharing
server.
7
Shared Folder : Displays a list of the shared
folders.
8
My Computer : Displays a list of the folders
and files in the PC.
functions.
- The Background Music and Background
Music Setting functions.
- Sorting files by preference in the Photo,
Music, and Movie folders.
- The Change Group function.
- The Safe Remove function.
Size
8
not locate your PC on the TV screen.
 AllShare does not support the following
Network Services
8. To select a device, use the RED(A) or
BLUE(D) button to select a file to play.
(For playing back Video, Music or Photos files,
see pages 43~51.)
 The search and skip operation may differ
depending on the sever function.
 During video playback, play time will not
display.
 To use AllShare function, please locate both
this product and PC in same subnet.
English
HT-C6950W_CIS_ENG_0407.indd 59
59
2010-04-08
6:27:00
Other information
Troubleshooting
Refer to the chart below when this product does not function properly. If the problem you are experiencing is
not listed below or if the instruction below does not help, turn off the product, disconnect the power cord
and contact the nearest authorized dealer or Samsung Electronics Service Centre.
Symptom
Check/Remedy
I cannot eject the disc.
• Is the power cord plugged securely into the outlet?
• Turn off the power and then turn it back on.
Playback does not start.
• Check the region number of the BD/DVD.
BD/DVD discs purchased from abroad may not be playable.
• CD-ROMs and DVD-ROMs cannot be played on this Product.
• Make sure that the rating level is correct.
Playback does not start
immediately when the
Play/Pause button is pressed.
• Are you using a deformed disc or a disc with scratches on the surface?
• Wipe the disc clean.
Sound is not produced.
• No sound is heard during fast playback, slow playback, and step motion playback.
• Are the speakers connected properly? Is the speaker setup correctly customized?
• Is the disc severely damaged?
Sound can be heard only from a
few speakers and not all 8.
• On certain BD/DVD discs, sound is output from the front speakers only.
• Check if the speakers are connected properly.
• Adjust the volume.
• When listening to a CD, radio or TV, sound is output to the front speakers only.
PL II (Dolby Pro Logic II) on the remote
Select "PRO LOGIC II" by pressing
control to use all six speakers.
Dolby Digital 7.1 CH Surround
Sound is not produced.
• Is there "Dolby Digital 7.1 CH" mark on the disc? Dolby Digital 7.1 CH Surround Sound is
produced only if the disc is recorded with 7.1 channel sound.
• Is the audio language correctly set to Dolby Digital 7.1-CH in the information
display?
The remote control does not work.
• Is the remote control being operated within its operation range of angle and distance?
• Are the batteries drained?
• Have you selected the mode(TV/BD) functions of the remote control (TV or BD) correctly?
• Disc is rotating but no
picture is produced.
• Is the TV power on?
• Are the video cables connected properly?
• Is the disc dirty or damaged?
• A poorly manufactured disc may not be playable.
• Picture quality is poor and
picture is shaking.
Audio language and subtitles do
not work.
• Audio language and subtitles will not work if the disc does not contain them.
Menu screen does not appear
even when the menu function is
selected.
• Are you using a disc that does not contain menus?
60
English
HT-C6950W_CIS_ENG_0407.indd 60
2010-04-08
6:27:01
06
Check/Remedy
Aspect ratio cannot be changed.
• You can play 16:9 BD/DVDs in 16:9 Wide mode, 4:3 Letter Box mode, or 4:3
Pan - Scan mode, but 4:3 BD/DVDs can be seen in 4:3 ratio only. Refer to the
Blu-ray Disc jacket and then select the appropriate function.
• The product is not working.
(Example: The power goes out
or a strange noise is heard.)
• Turn off the power, and press and hold the STOP ( ) button on the product
for longer than 5 seconds.
• The Product is not working
normally.
The rating level password has
been forgotten.
Other information
Symptom
- Using the RESET function will erase all stored settings.
Do not use this unless necessary.
• With no disc in the product, press and hold the product's STOP ( ) button for
longer than 5 seconds. INIT appears on the display and all settings will return
to the default values.
And then press the POWER button.
- Using the RESET function will erase all stored settings.
Do not use this unless necessary.
Can't receive radio broadcasts.
• Is the antenna connected properly?
• If the antenna's input signal is weak, install an external FM antenna in an area
with good reception.
While listening to TV audio
through the Product, no sound is
heard.
• If the OPEN/CLOSE ( ) button is pressed while listening to TV audio using the
D.IN or AUX functions, the BD/DVD functions are turned on and the TV audio is
muted.
"Not Available" appears on
screen.
• The features or action cannot be completed at this time because:
1. The BD/DVD’s software restricts it.
2. The BD/DVD’s software doesn’t support the feature (e.g., angles)
3. The feature is not available at the moment.
4. You’ve requested a title or chapter number or search time that is out of range.
If the HDMI output is set to a
resolution your TV cannot support
(for example, 1080p), you may not
see a picture on your TV.
• Press the STOP ( ) button (on front panel) for more than 5 seconds with no
disc inside. All settings will revert to the factory settings.
No HDMI output.
• Check the connection between the TV and the HDMI jack of the Product.
• Check if your TV supports 576p(480p)/720p/1080i/1080p HDMI input
resolution.
Abnormal HDMI output screen.
• If random noise appears on the screen, it means that TV does not support
HDCP (High-bandwidth Digital Content Protection).
• When the factory default settings are restored, all the user data stored in the
BD data will be deleted.
English
HT-C6950W_CIS_ENG_0407.indd 61
61
2010-04-08
6:27:01
Other information
Symptom
Check/Remedy
PC Share Manager function
I can see folders shared through the
PC Share Manager, but I cannot see
the files.
• Since it shows only files corresponding to the Image, Music, and Movie
categories, files that do not correspond to these categories may not be
displayed.
AllShare function
Video is played intermittently.
• Check if the network is stable.
• Check if the network cable is properly connected and if the network is not
overloaded.
AllShare connection between TV
and PC is unstable.
• IP address under the same subnetwork should be unique, otherwise IP
collision can results in such a phenomenon.
• Check if you have a firewall enabled.
If so, disable the firewall function.
BD-LIVE
I cannot connect to the BD-LIVE
server.
• Check whether the network connection is successful or not by using Network
Test menu. (See page 40)
• Check whether the USB memory device is connected with product or not.
• The memory device must have at least 1GB of free space to accommodate the
BD-LIVE service.
You can check the available size in BD Data Management. (See page 37)
• Please check whether the BD-LIVE Internet Connection menu is set to
Allow(All).
• If all above fails, contact the contents provider or update the latest firmware.
When using the BD-LIVE service,
an error occurs.
• The memory device must have at least 1GB of free space to accommodate the
BD-LIVE service.
You can check the available size in BD Data Management. (See page 37)
✎ NOTE
 When the factory default settings are restored, all the user data stored in the BD data will be deleted.
62
English
HT-C6950W_CIS_ENG_0407.indd 62
2010-04-08
6:27:01
06
Other information
Specifications
General
FM Tuner
Weight
3.8 kg
Dimensions
430 (W) x 61 (H) x 330 (D) mm
Operating Temperature Range
+5°C to +35°C
Operating Humidity Range
10 % to 75 %
Signal/noise ratio
70 dB
Usable sensitivity
10 dB
Total harmonic distortion
0.5 %
BD (Blu-ray Disc)
Reading Speed : 4.917m/sec
DVD (Digital Versatile Disc)
Disc
CD : 12cm (COMPACT DISC)
CD : 8cm (COMPACT DISC)
Composite Video
Reading Speed : 3.49 ~ 4.06 m/sec.
Approx. Play Time (Single Sided, Single Layer Disc) : 135 min.
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 74 min.
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 20 min.
1 channel : 1.0 Vp-p (75 Ω load)
Blu-ray Disc : 576i(480i)
DVD : 576i(480i)
Y : 1.0 Vp-p (75 Ω load)
Video Output
Pr : 0.70 Vp-p (75 Ω load)
Component Video
Pb : 0.70 Vp-p (75 Ω load)
Blu-ray Disc : 1080i, 720p, 576p(480p), 576i(480i)
DVD : 576p(480p), 576i(480i)
Video/Audio
HDMI
2D : 1080p, 1080i, 720p, 576p(480p)
3D : 1080p, 720p
Front speaker output
165W x 2(3Ω)
Centre speaker output
170W(3Ω)
PCM multichannel audio, Bitstream audio, PCM audio
Amplifier
Surround speaker output
165W x 2(3Ω)
Surround Back Speaker output
165W x 2(3Ω)
Subwoofer speaker output
Frequency response
170W(3Ω)
Analogue input
20Hz~20kHz (±3dB)
Digital input
20Hz~44kHz (±3dB)
S/N Ratio
70dB
Channel separation
60dB
Input sensitivity
(AUX)500mV
English
HT-C6950W_CIS_ENG_0407.indd 63
63
2010-04-08
6:27:01
Other information
7.1ch speaker system
Speaker system
Speaker
Front/Surround
Surround back
3Ω
Centre
Subwoofer
3Ω
3Ω
Impedance
3Ω
Frequency range
140Hz~20kHz 140Hz~20kHz
Output sound pressure level
87dB/W/M
87dB/W/M
87dB/W/M
88dB/W/M
Rated input
165W
165W
170W
170W
Maximum input
330W
330W
340W
340W
Dimensions (W x H x D)
Front/Surround : 90 x 1300 x 119 mm (Stand base : 250 x 250 mm)
Surround back : 90 x 141.5 x 68.5 mm
Centre : 360 x 74.5 x 68.5 mm
Subwoofer : 168 x 350 x 295 mm
140Hz~20kHz 40Hz ~ 160Hz
Front/Surround : 3.27 kg, Surround back : 0.58 kg
Centre : 0.58 kg , Subwoofer : 4.5 kg
*: Nominal specification
- Samsung Electronics Co., Ltd reserves the right to change the specifications without notice.
- Weight and dimensions are approximate.
- Design and specifications are subject to change without prior notice.
- For the power supply and Power Consumption, refer to the label attached to the product.
Weights
SWA-5000
Weight
Dimensions (W x H x D)
Operating Temperature Range
Operating Humidity Range
Output
64
1.1 kg
Frequency range
76.2 x 228 x 152 mm
+5°C ~ +35°C
10% ~ 75%
165W x 2 CH
20Hz~20KHz
S/N Ratio
65dB
English
HT-C6950W_CIS_ENG_0407.indd 64
2010-04-08
6:27:01
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG
customer care centre.
Area
Contact Centre
` North America
Canada
1-800-SAMSUNG (726-7864)
Mexico
01-800-SAMSUNG (726-7864)
U.S.A
1-800-SAMSUNG (726-7864)
` Latin America
Argentine
0800-333-3733
0800-124-421
Brazil
4004-0000
Chile
800-SAMSUNG (726-7864)
Nicaragua
00-1800-5077267
Honduras
800-7919267
Costa Rica
0-800-507-7267
Ecuador
1-800-10-7267
El Salvador
800-6225
Guatemala
1-800-299-0013
Jamaica
1-800-234-7267
Panama
800-7267
Puerto Rico
1-800-682-3180
Rep. Dominica 1-800-751-2676
Trinidad &
1-800-SAMSUNG (726-7864)
Tobago
Venezuela
0-800-100-5303
Colombia
01-8000112112
` Europe
0810 - SAMSUNG
Austria
(7267864, € 0.07/min)
Belgium
02-201-24-18
Czech
800 - SAMSUNG
(800-726786)
70 70 19 70
030 - 6227 515
01 48 63 00 00
01805 - SAMSUNG
(726-7864 € 0,14/Min)
06-80-SAMSUNG (726-7864)
800-SAMSUNG (726-7864)
261 03 710
0900-SAMSUNG
(0900-7267864) (€ 0,10/Min)
815-56 480
0 801 1SAMSUNG (172678)
022-607-93-33
80820-SAMSUNG (726-7864)
0800-SAMSUNG (726-7864)
902 - 1 - SAMSUNG
(902 172 678)
0771 726 7864 (SAMSUNG)
0845 SAMSUNG (7267864)
0818 717100
Denmark
Finland
France
Germany
Hungary
Italia
Luxemburg
Netherlands
Norway
Poland
Portugal
Slovakia
Spain
Sweden
U.K
Eire
HT-C6950W_CIS_ENG_0407.indd 65
Web Site
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com/
be (Dutch)
www.samsung.com/
be_fr (French)
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
Area
Switzerland
Contact Centre
Web Site
0848 - SAMSUNG (7267864, www.samsung.com/ch
www.samsung.com/
CHF 0.08/min)
ch_fr/ (French)
8-800-77777
www.samsung.com
8000-7267
www.samsung.com
800-7267
www.samsung.com
Lithuania
Latvia
Estonia
` CIS
Russia
Georgia
Armenia
Azerbaijan
Kazakhstan
Uzbekistan
Kyrgyzstan
Tadjikistan
8-800-555-55-55
8-800-555-555
0-800-05-555
088-55-55-555
8-10-800-500-55-500
8-10-800-500-55-500
00-800-500-55-500
8-10-800-500-55-500
Ukraine
0-800-502-000
Belarus
Moldova
` Asia Pacific
Australia
New Zealand
810-800-500-55-500
00-800-500-55-500
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.ua
www.samsung.com/
ua_ru
1300 362 603
www.samsung.com
0800 SAMSUNG (0800 726 786) www.samsung.com
400-810-5858
China
www.samsung.com
010-6475 1880
www.samsung.com/
hk
Hong Kong
(852) 3698-4698
www.samsung.com/
hk_en/
3030 8282
1800 110011
India
www.samsung.com
1800 3000 8282
1800 266 8282
0800-112-8888
Indonesia
www.samsung.com
021-5699-7777
Japan
0120-327-527
www.samsung.com
Malaysia
1800-88-9999
www.samsung.com
1-800-10-SAMSUNG
(726-7864)
1-800-3-SAMSUNG
Philippines
(726-7864)
www.samsung.com
1-800-8-SAMSUNG
(726-7864)
02-5805777
Singapore
1800-SAMSUNG (726-7864) www.samsung.com
1800-29-3232
Thailand
www.samsung.com
02-689-3232
Taiwan
0800-329-999
www.samsung.com
Vietnam
1 800 588 889
www.samsung.com
` Middle East & Africa
Turkey
444 77 11
www.samsung.com
South Africa
0860-SAMSUNG (726-7864) www.samsung.com
U.A.E
800-SAMSUNG (726-7864)
www.samsung.com
Bahrain
8000-4726
Jordan
800-22273
2010-04-08
6:27:02
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product should not
be disposed of with other household waste at the end of their working life. Where marked, the chemical
symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference
levels in EC Directive 2006/66. If batteries are not properly disposed of, these substances can cause harm
to human health or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of
waste and recycle them through your local, free battery return system.
Correct Disposal of This Product (Waste Electrical & Electronic
Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g.
charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life. To
prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these
items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office,
for details of where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract.
This product and its electronic accessories should not be mixed with other commercial wastes for disposal.
Code No. AH68-02279P
HT-C6950W_CIS_ENG_0408.indd 66
2010-04-08
6:34:00
Download PDF