Samsung | AP55Q1DN | Samsung AP55Q1DN User guide

AP50Q1C Series
AP55Q1C Series
AP55Q1D Series
Air Conditioner
user & installation manual
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service, please
register your product at
www.samsung.com/register
E A DB98-32202A(2)
AP50Q1C_IBIM_E 32202-2.indd 37
2010-07-14 오후 4:42:19
Register your product at www.samsung.com/register
Safety Precautions
The following safety precautions must be taken when using your air conditioner.
WARNING
During operation
• Risk of electric shock can cause injury or death. • Disconnect all remote
electric power supplies before servicing, installing or cleaning. • This
must be done by the manufacturer or its service agent or a similar
qualified person in order to avoid a hazard.
u Users of this product are cautioned not to attempt repair of this product at
their own discretion. Instead, they are requested to directly contact a designated service center or the outlet at which the product was purchased.
u Never spill any kind of liquid into the unit. Should this happen, unplug
or main switch off the unit and contact an authorized service center.
u Do not insert anything between the air outlet blades because the inner
fan may be damaged and could cause injury. Keep children away from the
unit.
u Do not place any obstacles in front of the unit.
u Do not spray liquid of any kind into the indoor unit. Should this happen,
switch off the breaker used for your air conditioner and contact your installation specialist.
u Make sure that the unit is correctly ventilated at all times:
Do not place clothing or other materials over it.
u If the wireless remote control will not be used for a long time, remove the
batteries. (If applicable)
u When using a wireless remote control, the distance should not be more than
7 m from the air conditioner. (If applicable)
Disposing of the unit
u B
efore throwing out the device, it is necessary to pull back the battery cells
and get rid of them safely for recycling reasons.
u When you need to dispose of the unit, consult your dealer. If pipes are
removed incorrectly, refrigerant may blow out and come into contact with
your skin, causing injury. Releasing refrigerant into the atmosphere also
damages the environments.
u P
lease recycle or dispose of the packaging material for this product in an
environmentally responsible manner.
Others
u Never store or ship the air conditioner upside down or sideways to avoid
damage to the compressor.
u T he appliance is not intended for use by young children or infirm
persons without supervision: Young children should be supervised to ensure
that they do not play with the appliance.
u Max current is measured according to IEC standard for safety and
current is measured according to ISO standard for energy efficiency.
E-2
AP50Q1C_IBIM_E 32202-2.indd 2
2010-07-14 오후 4:42:00
Contents
u
u
u
u
u
u
u
u
Preparing your air conditioner
 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  View of the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  Remote Control-Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  Inserting the Remote Control Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  Operating Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
4
5
5
6
6
Operating your air conditioner
 Cooling Your Room . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
 Heating Your Room . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
 Selecting the Automatic Operating Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
 Changing the Room Temperature Quickly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
 Operating to the Long Distance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
 Removing Excess Humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
 Airing Your Room . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
 Adjusting the Air Flow Direction Vertically . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
 Adjusting the Air Flow Direction Horizontally . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Programming your air conditioner
 Setting the Off Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
 Other Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Recommendations for use
 Operating Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
 Temperature and Humidity Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
 Cleaning Your Air Conditioner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
 Solving Common Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Technical specifications
 Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Installation part
 Accessory Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
 Selection of Installation Place . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
 Electrical Work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
 Installation Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
 Connection of Refrigerant Piping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
 Drilling a Hole in the Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
 Drain Hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
 Connecting the Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
 Air Purge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
 Refrigerant Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
 Check and Test Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Packing and unpacking guide
 Packing and Unpacking Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
How to connect your extended power cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
E-3
AP50Q1C_IBIM_E 32202-2.indd 3
2010-07-14 오후 4:42:00
View of the Unit
Indoor Unit
Air flow blades
(up/down orientation)
Air flow blades
(right/left orientation)
Air outlet
Remote control holder
Air filter
To open the grille
u Hold the
upper part of the grille, then
pull it slightly forward.
Air inlet
Control Panel
You can operate the air conditioner with the control panel when you do not wish to or
cannot operate the air conditioner with the remote control.
Using the control panel, you can adapt the On/Off, temperature, fan speed, operation
mode and air swing setting to your specific requirements.
Timer indicator
Operating mode indicators
(Cool, Heat, Auto, Dry, Fan)
Remote control sensor
Lock function indicator
Defrost indicator
Turbo function indicator
Set temperature
Indoor temperature
Outdoor operating indicator
On/Off button
Long function indicator
Fan speed
Temperature adjustment
buttons
Fan speed adjustment button
Operation mode selection button
Air Swing button
E-4
AP50Q1C_IBIM_E 32202-2.indd 4
2010-07-14 오후 4:42:01
Remote Control-Buttons
All air conditioner features except Lock function can be controlled from your seat by using the remote
control. You must operate the Turbo, Long function and Off Timer with the remote control.
Temperature adjustment buttons
Air flow swing buttons
Operation mode selection button
(Cool, Heat, Auto, Dry, Fan)
Off Timer button
Turbo/Long function button
(Only in the cool mode)
Fan speed adjustment button
On/Off button
Inserting the Remote Control Batteries
You must insert or replace the remote control batteries when :
u You purchase the air conditioner
u The remote control does not work correctly
Noteu Use two AAA, LR03 1.5V batteries.
u Do not use old batteries or different kinds of batteries together.
u Batteries may be completely discharged after 12 months,
even if they have not actually been used.
1
Push the battery cover on the rear of the remote control with your
thumb in the direction of the arrow and remove it.
2
Insert the two batteries, taking care to respect the polarities :
u + on the batt ery with + on the remote control.
u - on the battery with - on the remote control. 3
Close the cover by sliding it back until it clicks into place.
E-5
AP50Q1C_IBIM_E 32202-2.indd 5
2010-07-14 오후 4:42:02
Getting Started
You have just purchased a floor stand type air conditioner and it has been
installed by your installation specialist.
Your Manual contains valuable information on using your
air conditioner. Please take the time to read it as it will help you take full
advantage of the unit’s features.
The booklet is organized as follows.
u The following figures are shown on pages from 4 to 5 :
- Indoor unit
- Remote control(buttons and display)
They will help you find the buttons and understand the symbols displayed.
u In the manual, you will find a series of step-by-step procedures for each
function available.
The illustrations in the step-by-step procedures use three different symbols:
PRESS
PUSH
HOLD DOWN
For the...
The illustrations are...
Remote control
In the upper part.
Unit itself
In the lower part.
Operating Preparation
Look around the indoor and outdoor units. Confirm if any obstacles
that may prevent the air flow are present near the air conditioner.
Turn the power switch on.
IMPORTANT
T o operate the unit, the power switch is fitted to the wall
and should be set to ON.
E-6
AP50Q1C_IBIM_E 32202-2.indd 6
2010-07-14 오후 4:42:02
Cooling Your Room
You must select the Cool mode if you wish to adjust the :
 Cooling temperature
 Fan speed when cooling
1 If necessary, press the
(On/Off) button.
Result: u The power indicator on the control panel comes on.
u The indoor unit beeps.
The air conditioner is fitted with a protection mechanism
IMPORTANT
to prevent the unit from being damaged when it is
started immediately after being:
 Switched on
 Stopped
lt will start up normally after three minutes.
2 If the
is not displayed on the control panel, press the
button on the remote control one or more times until it appears.
Result:
u The indoor unit beeps each time you press the
Note
u The air conditioner runs in the Cool mode.
button.
You can change modes at any time.
3 To adjust the temperature, press the
buttons on the remote
control or
buttons on the control panel one or more times
until the required temperature is displayed. Possible temperatures
are between 18°C and 30°C inclusive.
Result:
u Each time you press the
buttons:
- The temperature is adjusted by 1°C.
- The indoor unit beeps.
u The air conditioner starts cooling, provided that
the room temperature is higher than the selected
temperature.
u If the room temperature reaches the set temperature,
the air conditioner stops cooling, but the fan is still
operating.
4 Select the fan speed by pressing the
button on the remote
control or
button one or more times until the required setting
is displayed :
Automatic(rotated :


)
Low
High
Turbo
Result:
Each time you press the
button, the indoor unit beeps.
5 To control the direction of the air flow, refer to page 14.
E-7
AP50Q1C_IBIM_E 32202-2.indd 7
2010-07-14 오후 4:42:04
Heating Your Room
You must select the Heat mode if you wish to adjust the :
 Heating temperature
 Fan speed when heating
1 If necessary, press the
Result:
(On/Off) button.
u The power indicator on the control panel comes on.
u The indoor unit beeps.
The air conditioner is fitted with a protection mechanism
IMPORTANT
to prevent the unit from being damaged when it is
started immediately after being:
 Switched on
 Stopped
lt will start up normally after three minutes.
2 If the
is not displayed on the control panel, press the
button on the remote control one or more times until it appears.
Result:
u The indoor unit beeps each time you press the
button.
u The air conditioner runs in the Heat mode.
Note
You can change modes at any time.
3 To adjust the temperature, press the
buttons on the remote
control or
buttons on the control panel one or more times
until the required temperature is displayed. Possible temperatures
are between 16°C and 30°C inclusive.
Result:
u Each time you press the
buttons:
- The temperature is adjusted by 1°C.
- The indoor unit beeps.
u The air conditioner starts heating, provided that the room
temperature is lower than the selected temperature.
u For the first 3~5 minutes, the fan may not operate to prevent
the cool air from running out of the indoor unit.
u If the room temperature reachs the set temperature, the air
conditioner stops heating, but the fan is still operating.
u The Defrost indicator( ) appears when frost forms on the
outdoor unit and disappears automatically after removing frost.
4 Select the fan speed by pressing the
button on the remote control
or
button one or more times until the required setting is displayed :
Automatic(rotated :


)
Low
High
Result:
Each time you press the
button, the indoor unit beeps.
5 To control the direction of the air flow, refer to page 14.
E-8
AP50Q1C_IBIM_E 32202-2.indd 8
NoteYou can't control the airflow direction when the fan
doesn't operate.
2010-07-14 오후 4:42:06
Selecting the Automatic Operating Mode
You can start the air conditioner in the Automatic mode.
In the Automatic mode, the temperature and the optimum fan speed
is selected automatically.
1 If necessary, press the
Result:
(On/Off) button.
u The power indicator on the control panel comes on.
u The indoor unit beeps.
IMPORTANT
The air conditioner is fitted with a protection mechanism
to prevent the unit from being damaged when it is
started immediately after being:
 Switched on
 Stopped
lt will start up normally after three minutes.
2 If the
is not displayed on the control panel, press the
button on the remote control one or more times until it appears.
Result:
Note
u The indoor unit beeps each time you press the
button.
u The air conditioner runs in the Auto mode.
u You can change modes at any time.
u If the indoor temperature is higher than 21°C, the air
conditioner operates in the Cool mode. If the indoor
temperature is lower than 21°C, the air conditioner
operates in the Heat mode.
 Cooling operation
 Heating operation
3 To control the direction of the air flow, refer to page 14.
E-9
AP50Q1C_IBIM_E 32202-2.indd 9
2010-07-14 오후 4:42:07
Changing the Room Temperature Quickly
The Turbo function is used to Cool /Auto(cool) your room as quickly as
possible.
Example : You have just come home and find that the room is very
hot. You wish to cool it down as quickly as possible.
The Turbo function operates for 30 minutes with the maximum setting
before returning automatically to the mode and temperature previously
selected.
1 If necessary, press the
Result:
(On/Off) button.
u The power indicator on the control panel comes on.
u The indoor unit beeps.
The air conditioner is fitted with a protection mechanism
IMPORTANT
to prevent the unit from being damaged when it is
started immediately after being:
 Switched on
 Stopped
lt will start up normally after three minutes.
2 Press the
Result:
button.
u The air conditioner cools the room as quickly as
possible.
u The temperature and fan settings are adjusted
automatically.
u After 30 minutes, the air conditioner is reset
automatically to the previous mode, temperature and
fan setting.
3 If you wish to stop the Turbo function before the end of 30-minute
period, press the
button twice.
Result:
u The air conditioner is reset automatically to the
previous mode, temperature and fan settings.
u You can't select the Turbo and Long function
simultaneously.
4 To control the direction of the air flow, refer to page 14.
E-10
AP50Q1C_IBIM_E 32202-2.indd 10
2010-07-14 오후 4:42:07
Operating to the Long Distance
The Long function is used to Cool /Auto(cool) your room as far as
possible. In the Long function, the up/down orientation of air flow
and fan speed are selected automatically.
1 If necessary, press the
Result:
(On/Off) button.
u The power indicator on the control panel comes on.
u The indoor unit beeps.
IMPORTANT
The air conditioner is fitted with a protection mechanism
to prevent the unit from being damaged when it is
started immediately after being:
 Switched on
 Stopped
lt will start up normally after three minutes.
2 Press the
Result:
button twice.
u The air conditioner cools the room as far as possible.
u The fan settings are adjusted automatically.
3 To adjust the temperature, press the
buttons one or more times
until the required temperature is displayed. Possible temperatures
are between 18°C and 30°C inclusive.
Result:
u Each time you press the
buttons:
- The temperature is adjusted by 1°C.
- The indoor unit beeps.
4 If you wish to stop the Long function, press the
again.
Result:
button
u The air conditioner is reset automatically to the
previous mode, temperature and fan settings.
3 To control the direction of the air flow, refer to page 14.
NoteYou can't control the airflow direction horizontally in the
Long function.
E-11
AP50Q1C_IBIM_E 32202-2.indd 11
2010-07-14 오후 4:42:08
Removing Excess Humidity
If the atmosphere in your room is very humid or damp, you can
remove excess humidity without lowering the room temperature too
much.
1 If necessary, press the
Result:
(On/Off) button.
u The power indicator on the control panel comes on.
u The indoor unit beeps.
The air conditioner is fitted with a protection mechanism
IMPORTANT
to prevent the unit from being damaged when it is
started immediately after being:
 Switched on
 Stopped
lt will start up normally after three minutes.
2 If the is not displayed on the control panel, press the
button on the remote control one or more times until it appears.
Result:
u The indoor unit beeps each time you press the
button.
u The air conditioner runs in the Dry mode.
Note
You can change modes at any time.
3 To adjust the temperature, press the
buttons one or more times
until the required temperature is displayed. Possible temperatures
are between 18°C and 30°C inclusive.
Result:
u Each time you press the
buttons:
- The temperature is adjusted by 1°C.
- The indoor unit beeps.
u The air conditioner starts removing the excess
humidity;
the quantity of air is adjusted automatically.
4 The fan speed is selected automatically(
: Automatic).
5 To control the direction of the air flow, refer to page 14.
E-12
AP50Q1C_IBIM_E 32202-2.indd 12
2010-07-14 오후 4:42:08
Airing Your Room
If the atmosphere in your room is stale, you can air the room using
the Fan feature.
1 If necessary, press the
Result:
(On/Off) button.
u The power indicator on the control panel comes on.
u The indoor unit beeps.
IMPORTANT
The air conditioner is fitted with a protection mechanism
to prevent the unit from being damaged when it is
started immediately after being:
 Switched on
 Stopped
lt will start up normally after three minutes.
2 If the
is not displayed on the control panel, press the
button on the remote control one or more times until it appears.
Result:
u The indoor unit beeps each time you press the
button.
u The air conditioner runs in the Fan mode.
Note
You can change modes at any time.
3 Select the fan speed by pressing the
button one or more
times until the required setting is displayed:
Low
High
Turbo
Result:
Each time you press the
button, the indoor unit
beeps.
4 To control the direction of the air flow, refer to page 14.
E-13
AP50Q1C_IBIM_E 32202-2.indd 13
2010-07-14 오후 4:42:09
Adjusting the Air Flow Direction Vertically
Depending on the position of the indoor unit in your room, you can
adjust the position of the outer air flow blade on the upper part of
the unit, thus increasing the efficiency of the air conditioner.
1 Press the
button.
Result: The outer blade moves up and down.
RECOMMENDATION
When...
Cooling
Adjust the blade to face...
Upwards.
Heating
Downwards.
2 To stop the blade moving up and down, press the
again.
button
Adjusting the Air Flow Direction Horizontally
There are two sets of air flow blades. Just as the outer air flow
blade can be adjusted vertically, the inner blade can be adjusted
horizontally.
1 Press the
button.
Result: The inner blade moves right and left.
2 To stop the blade moving right and left, press the
again.
Note
button
u You can't control the airflow direction horizontally in the
Long Function.
u You can't control the airflow direction when the fan
doesn't operate in the Heat mode.
E-14
AP50Q1C_IBIM_E 32202-2.indd 14
2010-07-14 오후 4:42:11
Setting the Off Timer
The Off Timer enables you to switch off the air conditioner
automatically after a given period of time. You can set the period of
time from 1 to 8 hours. You can select the Off Timer only when the
air conditioner is on.
To set the operating time, press the
button one or more times
until the required time is displayed. Possible time is between 1 hour
and 8 hours inclusive.
Result: u After blinking of the timer indicator for 5 seconds, it will be
changed to temperature setting.
u The air conditioner will switch off automatically after the
set time and the Off Timer indicator disappears.
Note
ou can see or change the setting mode and/or the
Y
temperature by pressing the
button or the
buttons after setting the Off Timer.
To Cancel the Off Timer
Press the
disappears.
one or more times until the Off Timer indicator
E-15
AP50Q1C_IBIM_E 32202-2.indd 15
2010-07-14 오후 4:42:11
Other Function
You can use the Lock function on the control panel of the indoor unit.
1 Press the
buttons simultaneously for 3 seconds.
Result: u indicates on the control panel.
u The control panel is locked.
NoteYou can use the remote control even if the control panel is
locked.
2 To cancel the Lock function, press the
simultaneously for 3 seconds once again.
buttons
Operating Recommendations
Here are a few recommendations that you should follow when using your air conditioner.
Topic
Recommendation
Heating performances
The heat pump inside the air conditioner absorbs heat from outside
air and brings it indoors. If the temperature of the outside air drops,
the air conditioner will heat less.
Warm air circulation
The air conditioner circulates warm air to heat your room; as a result,
some time will be required after starting the air conditioner to warm
the entire room. If necessary, set the air conditioner on before you
wish to use the room.
Frost
When outside temperatures are low and humidity is high, frost may
form in the outdoor unit when heating is selected.
If this happens:
 The heating operation is stopped.
 The Defrost( ) mode is triggered automatically for about
7 minutes.
No intervention is required from you; after about 7 minutes, the air
conditioner starts operating again normally.
High indoor and outdoor
temperatures
If both the indoor and outdoor temperatures are high and you select
the Heat mode, the outdoor unit’s fan and compressor may stop at
times. This is normal; simply wait until the air conditioner switches on
again.
Power failure
If a power failure occurs when the air conditioner is operating, the unit is switched off.
When the power returns, you must press the
(On/Off ) button to
restart it.
E-16
AP50Q1C_IBIM_E 32202-2.indd 16
2010-07-14 오후 4:42:12
Temperature and Humidity Ranges
The following table indicates the temperature and humidity ranges, within which the air conditioner
can be used.
If the air conditioner is used at...
Then...
High temperature
The automatic protection feature may be triggered and the air
conditioner stopped.
Low temperature
A water leakage or some other
malfunction may happen if the heat exchanger freezes.
High humidity levels
Water may condense on and drip from the surface of the
indoor unit if it is used for a long periods.
Mode
Outdoor Temperature
Indoor Temperature
Indoor Humidity
Heating
0°C to 24°C approx.
27°C or less.
-
Cooling
21°C to 54°C approx.
18°C to 32°C approx.
80% or less
Drying
18°C to 54°C approx.
18°C to 32°C approx.
-
g If the outdoor temperature is as low as 0°C, the heating capacity drops up to 70~80% depending on the
operation condition.
If the cooling operation is used at over 33°C(indoor temperature), it does not cool at its full capacity.
E-17
AP50Q1C_IBIM_E 32202-2.indd 17
2010-07-14 오후 4:42:12
Cleaning Your Air Conditioner
For the best use of your air conditioner, you must clean it every other
week regularly to remove the dust that accumulates on the air filter.
Before cleaning your air conditioner, ensure that you
IMPORTANT
have switched off the breaker for the unit.
1 Open the front grille, then pull out the air filter.
2 Remove all dust on the air filter with a vacuum cleaner or brush.
3 When you have finished, insert the air filter into the original
position and close the front grille.
4 Clean the unit with a damp cloth and mild detergent (do NOT use
benzene, solvents or other chemicals).
Note
If you have not used the air conditioner for a long period of
time, set the fan going for 3 to 4 hours to dry the inside of the air
conditioner thoroughly.
E-18
AP50Q1C_IBIM_E 32202-2.indd 18
2010-07-14 오후 4:42:12
Solving Common Problems
Before contacting the after-sales service, perform the following simple checks.
They may save you the time and expense of an unnecessary call.
Problem
Explanation/Solution
The air conditioner does not
operate at all
 Check that the breaker used for the air conditioner is switched on.
 Check that the indoor unit is turned on;
if necessary press the
(On/Off ) button on the remote control.
 Check whether the Timer indicator on the indoor unit is switched on.
If so:
- Wait until the switch-on time is reached and the air conditioner
starts up automatically.
- Cancel the Timer (see page 15 for further details)
The air conditioner does not
operate with the remote
control
 Check that there are no obstacles between you and the indoor unit.
 Check the remote control batteries.
 Check that you are close enough to the indoor unit (7 metres /yards
or less).
No beep is heard when you
press the
(On/Off ) button
on the remote control
 Check that you are pointing the remote control at the remote
control sensor of the indoor unit.
 Replace the remote control batteries if necessary.
The air conditioner does not
cool or heat
 Check that the correct operating mode has been selected
(Cool, Auto, Heat).
 The room temperature may be too low or too high.
 Dust may be blocking the air filter guard; refer to page 19 for
cleaning instructions.
 Check that there is no obstacle in front of the outdoor unit.
The fan speed does not
change
when you press the
button
 Check that the operating mode is set to Cool, Heat or Fan ;
in the Auto, Turbo, Long and Dry mode, the fan speed is controlled
automatically.
The air flow direction does not  Check that the air conditioner has been switched on; if necessary,
change when you press the
press the
(On/Off ) button on the remote control.
or
button
The Timer is not correctly
triggered
 Check that the timer has been programmed correctly; see page 15.
Odour is permeated in the
room during air conditioning
 Air the room.
Smoke is generated from the
outdoor unit.
 It may not be a fire but it can be a steam generated by the defrost
operation from outdoor heat exchanger during Heat mode in winter.
E-19
AP50Q1C_IBIM_E 32202-2.indd 19
2010-07-14 오후 4:42:13
Technical Specifications
Model
Power Supply
AP50Q1C Series
3N~, 380V, 50Hz
AP55Q1C Series
AP55Q1D Series
3~, 220V, 60Hz
E-20
AP50Q1C_IBIM_E 32202-2.indd 20
2010-07-14 오후 4:42:13
 Be sure to read the manual carefully to ensure sufficient realization of the excellent performance
of the unit.
 Be sure to drill a hole in the wall necessary for installation before attempting to install the unit.
 After completion of installation, be sure to perform a test operation of the unit to check for
any problem, and then deliver the unit to the customer if the test results are acceptable.
 After completion of test operation, hand over the manual and warranty card to the customer.
 As the installation work requires special skill, be sure to request a qualified dealer to take
care of the installation of your unit; the user should not attempt to install his/her unit by
himself/herself.
 Do not attach any electric heating device or electric heater to the unit. Do not attempt to
disassemble or modify the unit by yourself. (It may cause machine trouble, electric shock or fire.)
Accessory Parts List
No.
Part Name
1
Drain hose
2
Connecting pipe
3
Connecting pipe
4
Connection wiring (3 strand)
5
Insulation for piping
6
Finishing tape
Remarks
No.
Part Name
8
Drain plug
ø9.52mm
(3/8 inch)
9
Cable tie
ø19.05mm
(3/4 inch)
10 Putty
Piping
box
11 Pipe band
Remarks
Piping
box
12 Cover hole
13 Screw
7
Wire of sensor (2 strand)
g The type and quantity may differ depending on the specifications.
E-21
AP50Q1C_IBIM_E 32202-2.indd 21
2010-07-14 오후 4:42:13
Selection of Installation Place
Indoor Unit
Top view
 Install the unit at a place close to the wall facing the outside as it is necessary
to perform piping connection with the outdoor unit.
- It is effective to install the unit at a window side to ensure uniform
distribution of indoor temperature.
 Install the unit at a place where there is no obstacle against the wind around
the air inlet and air outlet.
 Install the unit horizontally at a stable, rigid place.
(When installing the unit at a place subjected to oscillation, noise may occur.)
 Avoid a place near the door which is frequented by people.
 Avoid a place subject to direct sunlight.
Above 50cm
Side view
Above 20cm
Outdoor Unit
 Do not install the outdoor unit on a wood palette.
 Fix the outdoor unit completely to the base surface with anchor bolts.
 The manufacturer is not responsible for the damage occurred by not
keeping standard of the installation.
Above 100cm
 A place free from the risk of combustible gas leakage.
 A place which can bear the weight of the unit.
 A place which can bear the fixing strength of the outdoor unit.
 Avoid a place subject to oil (including machine oil).
 Avoid a saline place.
 Avoid a place subject to sulfide gas (hot spring zone).
(When installing the unit at such special environmental conditions, it may cause machine trouble. When it is unavoidable to use such places, It requires special maintenance.)
 A place where the discharge air and noise of the outdoor unit do not disturb the neighborhood.
(Take special care not to cause any inconvenience to your neighbors when installing the unit on the
borderline with your neighborhood.)
 A place where strong wind does not head against the air outlet of the outdoor unit. (If a strong wind
heads directly against the air outlet at the time of cooling operation, a safety device can be operated.)
 Do not install the outdoor unit at an unstable place such as outer wall of an apartment or building.
The outdoor unit may fall down, causing severe personal or property damage or loss.
1. When installing the unit at a roadside concentrated with buildings,
install it parallel with the road.
2. Install the unit so that the air outlet faces toward the wall at a place
such as rooftop, which may be subjected to strong wind.
Wall
Air outlet
 If there is any unavoidable reason to install the unit at such a place,
take the following measures against the wind;
Strong
wind
Roof top
 The outdoor unit should be installed in accordance with the service space.
Above 60cm
Above 50cm
Space for piping
and wiring
Above 50cm
Above 30cm
Space for piping
and wiring
The air inlet faces toward the wall.
Above 30cm
Above 60cm
The air outlet faces towards the wall.
E-22
AP50Q1C_IBIM_E 32202-2.indd 22
2010-07-14 오후 4:42:14
Electrical Work
The electrical work should be performed by a specialist qualified for the work.
 Use the three phase power supply, and be sure to install the sub power distribution board for exclusive
use with the unit(separately purchased by the user).
 Do not connect multiple plugs to an outlet at once because it can cause a drop in voltage,
resulting in poor performance of the automatic control circuit.
 Be sure to install circuit breaker (Extra purchased by the user).
 Be sure to connect the grounding wire.
 If the terminal is loose, fire may occur by arc.
If the terminal is connected too firmly, the terminal may be damaged.
Tightening torque (kgf•cm)
M3
5.9
1 Phase 220V
M4
30.0
3 Phase 380V
Electric power specification
MODEL
AP50Q1C Series
AP55Q1C/AP55Q1D Series
3N~, 380V, 50Hz
3~, 220V, 60Hz
50 A
50 A
Switch
30 A
30 A
Fuse
30 A
30 A
Size of grounding wire
2.0mm2
2.0mm2
Min. size of electric wires from/
to the indoor/outdoor unit
0.75mm2
0.75mm2
5.5/3.5mm2
5.5/3.5mm2
Power
Ampere of breaker
Knife switch
Size of electric input wires
 Be sure to use the wires, and switches or fuses of power distribution board are qualified and fulfill
the specification.
 Be sure to install knife switch or circuit breaker on the power distribution board.
 The electrical and grounding work should be performed as per “ technical specifications of
electrical facilities ” and “ specifications of internal wiring ”.
 Be sure to connect the main electrical input wires with bolted connectors using compressed
terminal.
E-23
AP50Q1C_IBIM_E 32202-2.indd 23
2010-07-14 오후 4:42:14
Electrical Work (Continued)
AP50Q1C Series
When connecting 3Phase 4wires 380V AC
When using NFB (No Fuse Breaker)
 The outdoor unit circuit is shipped based on the NFB power source wiring.
1. Remove the cover of electric box on side panel of the outdoor unit.
2. Connect the electric input wires (R,S,T,N) to each terminal (R,S,T,N) of the electric box on the outdoor
unit respectively. (Input wires are purchased by the user separately.)
3. Connect the electric wires to each terminal on the indoor and outdoor unit respectively.
OUTDOOR SIDE
Power terminals on the outdoor unit
Connector Knife switch or
automatic circuit breaker
Brown
Blue
Blue
Wire of communication
NFB
Brown
Indoor/outdoor unit
connecting wire
Electric input wires
When using ELB (Earth Leakage Circuit Breaker)
1. Remove the cover of electric box on side panel of the outdoor unit.
2. Disconnect the connector A(R-L connection) from the outdoor unit.
3. Connect the electric input wires(R,S,T) to each terminal(R,S,T) and input wires(N,L) to each terminal(N,L)
of the electric box on the outdoor unit respectively. (Input wires are purchased by the user separately.)
4. Connect the electric wires to each terminal on the indoor and outdoor unit respectively.
OUTDOOR SIDE
Brown
Power terminals on the outdoor unit
Break Connector Blue
Blue
Wire of communication
Brown
Indoor/outdoor unit
connecting wire
Electric input wires
E-24
AP50Q1C_IBIM_E 32202-2.indd 24
2010-07-14 오후 4:42:15
AP55Q1C/AP55Q1D Series
When connecting 3Phase 3wires 220V AC
1. Remove the cover of electric box on side panel of the outdoor unit.
2. Connect the electric input wires(R, S, T) to each terminal(R, S, T) of the electric box on the outdoor unit
respectively. (Input wires are purchased by the user separately.)
3. Connect the electric wires to each terminal on the indoor and outdoor unit respectively.
OUTDOOR SIDE
Power terminals on the outdoor unit
Connector
Knife switch or
automatic circuit breaker
NFB
Brown
Blue
Wire of communication
Blue
Brown
Indoor/outdoor unit
connecting wire
Electric input wires
E-25
AP50Q1C_IBIM_E 32202-2.indd 25
2010-07-14 오후 4:42:15
Installation Procedures
1. Open the front panel, and remove the flare nut.
2. Bend the connection pipe to an appropriate length using the spring bender depending upon the
installation place.
- Allowable pipe length : Maximum 25m
- Allowable pipe drop distance : Maximum 15m
- Make no more than ten bending points on the pipe
 When the pipe length is in excess of the standard pipe length of 5m, add the refrigerant (R22) of
75g(AP50Q1C Series) / 80g(AP55Q1C/AP55Q1D Series) for each additional 1m.
 Additional Refrigerant
Example:15m pipe length, additional refrigerant to be charged is
(15m-5m)X75g/m=750g(AP50Q1C Series), (15m-5m)X80g/m=800g(AP55Q1C/AP55Q1D Series)
I f the pipe is lengthened, the performance of the unit is degraded, and the service life is
shortened. Therefore, the pipe length should be as short as possible (less than 25m).
Indoor unit
Indoor unit
Indoor unit
Fix the pipe
Less than 6m
Outdoor unit
Less than 15m
Less than 15m
Outdoor unit
S-TRAP
Outdoor unit
Fix the pipe (Every 6m)
3. Install the high pressure pipe to the heat exchanger liquid pipe, and the low pressure pipe to the heat
exchanger gas pipe respectively using the flare nut, taking care not to cause any leakage of refrigerant.
4. Be sure to insulate the pipe with appropriate insulation material.
5. Insert the drain hose into the drain pipe, and connect them by tying them to the cable tie to prevent any
water leakage.
6. After completion of the installation, check the connecting area for any gas leakage.
7. Wind a finish tape when the wiring of the refrigerant pipe, the unit, and the drain piping are completed.
Indoor unit
checking area
Outdoor unit
checking area
E-26
AP50Q1C_IBIM_E 32202-2.indd 26
2010-07-14 오후 4:42:15
Connection of Refrigerant Piping
When installing, make sure there is no leakage. When recovering the refrigerant, ground the
compressor first before removing the connection pipe. If the refrigerant pipe is not properly
connected and the compressor works with the service valve open, the pipe inhales the air and it
makes the pressure inside of the refrigerant cycle abnormally high. It may cause explosion and injury.
Flare Processing
1. Cut the pipe using the pipe cutter.
90
Oblique
Roughness
Burr
2. Insert the flare nut into the pipe, and then perform the flare processing.
Outer Diameter
A(mm)
9.52mm
1.8
19.05mm
2.2
A
Pipe Bending
1. Perform bending of the pipe using the bender which has a specified bending
radius.
2. Be sure to take full care to perform bending of the pipe successfully at one
time. Bending and unbending the pipe more than twice makes the bending
work increasingly difficult.
3. You may use the spring inserted into the gas pipe instead of the bender to
bend the pipe.
4. When you bend the pipe using the spring, hold the pipe with both hands to
prevent any distortion, and secure a minimum bending radius of more than
100mm.
Spring
Tightening of Connection Parts
 Align the center of the connection piping, and tighten the flare nut by
turning it with hand. Then tighten it again using the torque wrench in the
direction as shown in the figure.
Outer Diameter
9.52mm
19.05mm
Torque (kgf•cm)
250~280
990~1210
Remarks
-
E-27
AP50Q1C_IBIM_E 32202-2.indd 27
2010-07-14 오후 4:42:16
Drilling a Hole in the Wall
 Drill a hole of 70mm in diameter to the outside.
 The drilling should be done at a distance of less than
150mm from the floor facing the indoor unit.
ø70mm
Less than
150mm
Drain Hose
 Extend the drain hose to the drain hose connected to
the drain pan, and fix it with the tape or a cable-tie to
prevent separation. Then make a covering of it so that
water cannot flow outwardly.
Piping Material
Vinyl Chloride (Outer diameter ø16mm)
Insulator
Foamed Polyethylene
Drain pan
Band
Drain hose
Insulation
Indoor and outdoor
unit connection
1. A
s the draining is of natural drain type, make the drain hose direct downward.
2. If there is any foreign substance in the drain plate, it may clog the drain pipe.
Therefore, be sure to remove the foreign substance inside after installation.
3. After completion of installation, be sure to pour water into the drain pan, and then check
the draining condition.(There is no problem in draining when the draining is completed
within 20 seconds.)
Connecting the Pipe
 The piping of this unit can be connected to the right, left, and rear side.
When you hit the area for piping connection slightly with a hammer, a hole is made.
 After connecting the piping and drain hose, insert the rubber cap as shown in the figure.
Holes for piping
connection (2 points)
E-28
Cover hole
 The shape of hole may vary with the models.
AP50Q1C_IBIM_E 32202-2.indd 28
2010-07-14 오후 4:42:16
Air Purge
 Be sure that all valve cocks are closed.
 The air in the indoor unit and in the pipe must be purged. If air remains in the refrigeration pipes, it will
affect the compressor, reduce cooling capacity and could lead to a malfunction. Use Vacuum Pump as shown at the figure.
1. Connect each assembly pipe to the appropriate valve on the outdoor unit and tighten the flare nut.
2. Connect the charging hose of low pressure side of manifold gauge to the packed valve having a service
port as shown at the figure.
3. Open the valve of the low pressure side of manifold gauge counter-clockwise.
4. Purge the air from the system using vacuum pump for about 30 minutes. - Close the valve of the low pressure side of manifold gauge clockwise.
- Make sure that pressure gauge show -0.1MPa(-76cmHg) after about 30 minutes.
- This procedure is very important in order to avoid gas leak.
- Turn off the vacuum pump.
- Remove the hose of the low pressure side of manifold gauge.
5. Set valve cork of both liquid side and gas side of packed valve to the open position.
6. Mount the valve stem nuts and the service port cap to the valve, and tighten them at the torque of
183kgf•cm with a torque wrench.
7. Check for gas leakage.
- At this time, especially check for gas leakage from the 3-way valve’s stem nuts, and from the service port cap.
Gas
pipe side
Indoor unit
OUTDOOR UNIT
D
Liquid
pipe side
Liquid
pipe side
A
B
Flare nut
Valve cock
Cap
3-way
valve
3-way
valve
Vacuum
Pump
C
Gas pipe side
B
A
Outdoor unit
Needle valve cap
E-29
AP50Q1C_IBIM_E 32202-2.indd 29
2010-07-14 오후 4:42:16
Refrigerant Charging
Air purge(at the time of new installation only)
Close the gas pipe side valve by turning it
clockwise.
Connect the pressure gauge to the low
pressure side service valve, and then open
the gas pipe side valve again.
Connect it to the refrigerant filling tank.
OUTDOOR UNIT
Gas
pipe side
Liquid
pipe side
Start cooling operation.
Check the pressure of the pressure gauge.
Check whether the low pressure side is within
the range of 4.5~5.6kg/cm2G
(outside temperature 35°C).
Open the tank and refill the refrigerant
until arriving at the proper pressure.
(Refill the refrigerant slowly checking the pressure.)
Stop operation.
Close the gas pipe side valve, and loosen
the pressure gauge connected.
Then open the gas pipe side valve again.
Tighten the cap of each valve using a specified tool.
 Always use R22 refrigerant to avoid damage of the unit or an explosion.
 Must keep the quantity of refrigerant by using a balance.
Do not use a manometer or not depend on your experiences.
E-30
AP50Q1C_IBIM_E 32202-2.indd 30
2010-07-14 오후 4:42:17
Check and Test Operation
Check
 Be sure to check the following again after completion of installation.
1. Check the piping connection area for any gas leakage.
Outdoor
connection area
Indoor
connection area
2. Is the drain hose properly connected?
Drain hose
3. Is the insulation of the piping in good condition?
Indoor and
outdoor unit connection
4. Is grounding properly made?
Insulation
E-31
AP50Q1C_IBIM_E 32202-2.indd 31
2010-07-14 오후 4:42:17
Check and Test Operation (Continued)
Test Operation
 After checking, read the manual carefully, and perform a test operation.
Then deliver the unit to the customer. (When delivering the unit, be sure to read carefully and follow the contents of the manual.)
1. Be sure to check whether the service valve is opened before attempting to perform the test
operation.
2. Never attempt to start test operation by force pressing the electronic contactor as it is very
dangerous.
(This is very dangerous as the protective device does not work.)
3. Be sure to perform the test operation after installation. It is easy to start the test operation
in winter if you increase the sensor temperature to 23°C ~ 25°C by holding the indoor
temperature sensor. (Cooling operation)
 When the outdoor temperature is below zero, do not test operation for more than
3 minutes. Otherwise, the compressor will be damaged.
Temperature sensor
E-32
AP50Q1C_IBIM_E 32202-2.indd 32
2010-07-14 오후 4:42:17
Packing and Unpacking Guide
Indoor unit
Cushion-top
Packing case
Cushion-mid
Indoor unit
Cushion-bottom
 Packing the unit as below procedure
1. Put the indoor unit onto the cushion-bottom.
2. Assemble cushion-mid of indoor unit.
3. Put the cushion-top onto the indoor unit.
4. Put the packing case from the top of set.
5. Seal the packing case.
 Unpacking the unit as below procedure
1. Take out the packing case from the set.
2. Take out the cushion-top.
3. Take out the cushion-mid.
4. Move the set from the cushion-bottom.
E-33
AP50Q1C_IBIM_E 32202-2.indd 33
2010-07-14 오후 4:42:17
Packing and Unpacking Guide (Continued)
Outdoor unit
Cushion-top
Outdoor unit
Packing case
4 screws
Wood palette
 Packing the unit as below procedure
1. Fix the outdoor unit and the wood palette by 4 screws.
2. Put the cushion-top onto the outdoor unit.
3. Put the packing case from the top of set.
4. Seal the packing case.
 Unpacking the unit as below procedure
1. Take out the packing case from the set.
2. Take out the cushion-top.
3. Unscrew 4 screws from the wood palette and then move the set.
E-34
AP50Q1C_IBIM_E 32202-2.indd 34
2010-07-14 오후 4:42:18
How to connect your extended power cables
※ Items to prepare
(compressor and insulation tape should be prepared by an installation technician.)
Tools
Spec
Crimping plier
Connection sleeve (mm)
Insulation tape
Contraction tube (mm)
MH-14
20xØ7.0(HxOD)
Width 18mm
50xØ8.0(LxOD)
Shape
1. As shown in the figure, peel off the shields from the rubber/wire of the power cable. - Peel off 20 mm of the wire shields of the tube installed already.
(Unit: mm)
Power cable (provided by us)
20
After peeling off the tube wire, you must insert a
contraction tube.
20
20
60
120
180
Wire tube power cable
20
2. Insert both sides of core wire of the power cable into the connection sleeve.
Connection sleeve
3. Using a compressor, compress the two points and flip it over and compress another two points in the same location.
- The compression dimension should be 8.0.
- After compressing it, pull both sides of the wire to make sure it is firmly pressed.
Comp. dim.
Compress it 4 times
5mm
4. Wrap it with the insulation tape twice and position your contraction tube in the middle of the insulation tape.
5. Apply heat to the contraction tube to contract it.
6. After tube contraction work is completed, wrap it with the
insulation tape to finish.
Insulation tape
40mm
Contraction tube
Insulation tape
In case of extending the electric wire, please DO NOT use a
round-shaped pressing socket.
- Incomplete wire connections can cause electric shock or a fire
E-35
AP50Q1C_IBIM_E 32202-2.indd 35
2010-07-14 오후 4:42:19
QUESTIONS OR COMMENTS?
COUNTRY
CALL
OR VISIT US ONLINE AT
444 77 11
www.samsung.com
SOUTH AFRICA
0860-SAMSUNG (726-7864)
www.samsung.com
U.A.E
800-SAMSUNG (726-7864)
www.samsung.com
TURKEY
BAHRAIN
8000-4726
JORDAN
800-22273
AP50Q1C_IBIM_E 32202-2.indd 36
2010-07-14 오후 4:42:19
Download PDF

advertising