Samsung | LS32A23W | Samsung LS32A23W الدليل السريع

BN68-00448G-00Eng.q
9/24/03 4:10 PM
Page 7
Viewing the Connection Panel
Power Input
☛
Whenever you connect an audio or video system to your set, ensure that all elements are switched
off.
1 Connecting an Aerial or Cable Television Network
To view television channels correctly, a signal must be received by the set from one of the following sources:
- An outdoor aerial
- A cable television network
- A satellite network
2 Connecting DVD, VCR or DTV Set-Top Box
- Connect the RCA Cable to “AUDIO(L)” and “AUDIO(R)” on the rear of your set and the other end to
“Audio Out” connector of the DVD, VCR, or DTV Set-Top Box.
- Connect the RCA Cable to “Y”, “Pb”, and “Pr” on the rear of your set and the other end to “Component Out”
connector of the DVD, VCR, or DTV Set-Top Box.
3
Connecting External A/V Devices
- Connect RCA or S-VIDEO cable to an appropriate external A/V device such as VCR, DVD or Camcorder.
- Connect RCA audio cables to “AUDIO(L)” and “AUDIO(R)” on the rear of your set and the other ends to
corresponding audio out connectors on the A/V device.
- Headphone may be connected to the headphone output ( 4 ) on the rear of your set. While the headphone
is connected, the sound from the built-in speakers will be disabled.
English-1
BN68-00448G-00Eng.q
9/24/03 4:10 PM
Page 8
Viewing the Connection Panel
5
Connecting Component Devices (DTV/DVD)
- Connect component video cables to component connector (“Y”,“Pb”,“Pr”) on the rear of your set and the
other ends to corresponding component video out connectors on the DTV or DVD.
- If you wish to connect both the Set-Top Box and DTV (or DVD), you should connect the Set-Top Box to the
DTV (or DVD) and connect the DTV (or DVD) to component connector (“Y”,“Pb”,“Pr”) on your set.
- The Y, Pb and Pr connectors on your component devices (DTV or DVD) are sometimes labeled Y, B-Y and
R-Y or Y, Cb and Cr.
- Connect RCA audio cables to “AUDIO(L)” and “AUDIO(R)” on the rear of your set and the other ends to
corresponding audio out connectors on the DTV or DVD.
Source
Video
Horizontal Frequency
(kHz)
Vertical Frequency
(Hz)
Resolution
(Lines)
TV/VIDEO
PAL
SECAM
NTSC4.43
NTSC3.58
15.625
15.625
15.734
15.704
50
50
60
60
575
575
483
483
480/60i
480/60p
576/50i
576/50p
720/60p
1080/50i
1080/60i
15.734
31.469
15.625
31.250
45.000
28.125
33.750
60
60
50
50
60
50
60
483
483
576
576
720
1080
1080
Component 1/2
6
Connecting Computer
- Connect the DVI connector to the PC video connector.
- Connect the stereo audio cable to “PC AUDIO IN (STEREO)” on the rear of your set and the other end to
“Audio Out” of the sound card on your computer.
7
Connecting Digital Audio Inputs
Connect optical digital audio cable or coaxial cable (RCA audio cable) to “DIGITAL AUDIO IN” on the rear of
your set and the other end to “DIGITAL OUT” of the equipment with a digital output to enjoy digital sound
(Multi-Channel Surround Sound, Stereo or Dolby Pro-Logic II).
English-2
BN68-00448G-00Eng.q
9/24/03 4:10 PM
Page 9
Viewing the Connection Panel
8
Connecting 5.1 Channel Speakers For Home Theater
Surround
Speaker
Surround
Speaker
Woofer
Main Speaker
Main Speaker
The other speakers
(Surround/Center/Sub
woofer):Connect the each
speaker audio cable to the
speaker output jack(surround 10
/Center 12 / Woofer 11
1 )on the
rear of your set making sure
that the +, - polarities are
correctly aligned.
LCD TV Rear
the speaker cable on
➢ Wind
the core twice or more.
Center Speaker
9 Main Speaker : When the speakers are separated from LCD TV
Connect the speaker audio cables to the main
speaker output jacks on the rear of your set
making sure that the +, - polarities are correctly
aligned.
➢
The speakers MUST have more than
10watts rating (Impedance 8Ω).
9 Main Speaker : When the speakers are attached with LCD TV
Mount the brackets on the speaker
and your set.
Connect the speaker and your set
using screws.
English-3
BN68-00448G-00Eng.q
9/24/03 4:12 PM
Page 54
How to Install the Wall Bracket
List of Contents
Wall bracket
Main body bracket
Screws
1 Bracket bar
Plastic screw anchors: 4
1 Wall bracket plate
2 Brackets
(Left and Right)
(The two brackets
are interchangeable.)
Screws: 4
Screws: 8
2 Assembly hinges
(Make sure they are a
left/right pair.)
How to Adjust the Angle of the Bracket
➢ Please adjust the angle of the bracket to 0 degrees before you fix it to the wall.
Captive screws
Make sure you put the right
hinge to the right side of the
bracket and vice versa.
Be aware of the correct installation direction
of the bracket when you set the angle to 30
and 32 degrees. (The direction for 30 and 32
degrees is indicated on the bracket surface.)
When you first open the box, the bracket is
not assembled.
Put the left and right brackets in the direction
of the arrow and tighten the captive screws.
English-4
1. Attach the LCD TV onto the wall bracket.
(Follow the instructions below.)
2. Pull the upper part of the LCD TV fixed to
the bracket forward in the direction of the
arrow and adjust the angle.
3. You can adjust the angle to your liking
between 0°~20°(±2°).
BN68-00448G-00Eng.q
9/24/03 4:12 PM
Page 55
How to Install the Wall Bracket
How to Attach the LCD TV to the Bracket
The LCD TV in the picture may not look exactly like yours.
(You assemble the plastic screw anchors and the screws the same way regardless of the model of your TV.)
1
Assemble the plastic screw anchors
and the screws. (See the picture below.)
2
Assemble the main body bracket as below
and put the plastic screw anchors in.
1) Attach the plastic screw anchors to
each of the left/right brackets as in 1.
2) Assemble the bracket bars to the
left/right brackets as in the picture
on the left.
They are left-right and upper-lower
symmetry and the assembly direction
does not matter.
3
4
Warning
1. Installing a wall bracket must be done by a
qualified professional installer.
2. After you hang the LCD TV on the wall
bracket, check from both sides to see if the
plastic screw anchors are securely in
place.
3. Be careful not to get your fingers caught
during installation or while adjusting the
angle of the bracket.
4. The LCD TV may fall from the wall and
hurt someone if the wall bracket is not
attached securely to the wall. Make sure
the bracket is screwed tightly to the wall.
Assemble the main body bracket as in the
pictures in 2. and below.
Put the four holders on the back of the TV
into the holes on the wall bracket, (1) lower
the TV, and (2) hang the TV on the bracket.
Fasten the TV securely to the wall bracket with
stickscrews as in (3) so that the two will not
separate.
LCD TV
Wall
Wall bracket
English-5
Download PDF

advertising