Samsung | PS-50P4H1 | Samsung PS-50P4H1 Operating instrustions

BN68-00718T-00Eng_1007
10/13/04
9:28 AM
Page 1
PDP-TELEVISION
(PLASMA DISPLAY PANEL)
Owner’s Instructions
Before operating the unit,
please read this manual thoroughly,
and retain it for future reference.
ON-SCREEN MENUS
PICTURE IN PICTURE (PIP)
COLOUR WEAKNESS ENHANCEMENT MODE
MY COLOUR CONTROL
TELETEXT (OPTION)
SRS TRUSURROUNDXT
DIGITAL NATURAL IMAGE ENGINE
This device is a Class B digital apparatus.
BN68-00718T-00Eng_1007
10/13/04
9:28 AM
Page 2
User Instructions
◆ Screen Image retention
Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the
plasma monitor panel for more than 2 hours as it can cause screen image retention. This image
retention is also known as “screen burn”. To avoid such image retention, reduce the degree of
brightness and contrast of the screen when displaying a still image.
◆ Height
The PDP can normally operate only under 2000m in height. It might abnormally function at a place
over 2000m in height and do not install and operate there.
◆ Heat on the top of the PDP TV
The top side of the product may be hot after long periods of use as heat dissipates from the panel
through the vent hole in the upper part of the product.
This is normal and does not indicate any defect or operation failure of the product.
However, children should be prevented from touching the upper part of the product.
◆ The product is making a ‘clacking’ noise.
A ‘cracking’ noise may occur when the product contracts or expands due to a change of
surrounding environment such as temperature or humidity. This is normal and not a defect of the unit.
◆ Cell Defects
The PDP uses a panel consisting of 1,230,000(SD-level) to 3,150,000(HD-level) pixels which require
sophisticated technology to produce. However, there may be few bright or dark pixels on the screen.
These pixels will have no impact on the performance of the product.
◆ Avoid operating the TV at temperatures below 5°C(41°F)
◆ A still image displayed too long may cause permanent damage to the PDP Panel
Watching the PDP TV in 4:3 format for a long period of time may leave
traces of borders displayed on the left, right and center of the screen caused
by the difference of light emission on the screen.
Playing a DVD or a game console may cause similar effect to the screen.
Damages caused by the above effect are not covered by the Warranty.
◆ Afterimage on the Screen.
Displaying still images from Video games and PC for longer than a certain period of time may
produce partial afterimages.
To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images for a
long time.
◆ Warranty
- Warranty does not cover any damage caused by image retention.
- Burn-in is not covered by the warranty.
English - 2
BN68-00718T-00Eng_1007
10/13/04
9:28 AM
Page 3
Checking Parts
Sold Separately
Owner’s Instructions
Ferrite Core for
Side AV Cable
S-VIDEO Cable
Remote Control/
AAA Batteries
Antenna Cable
Component Cables
(RCA)
Scart Cable
Speaker Wire
DVI Cable
PC Cable
PC Audio Cable
Power Cord
Ferrite Core (depending on the model)
The ferrite core is used to attenuate undesired signals.
When connecting cable, attach this ferrite core to
the cable near the connector.
When you connect Side AV cable to the AV3, first bind Side
AV Cable round the ferrite core to secure it.
DNIeTM (Digital Natural Image engine)
This feature bring you more detailed image with 3D noise
reduction, detail enhancement, contrast enhancement and
white enhancement. New image compensation Algorithm gives
brighter, clearer, much detailed image to you. DNIeTM
technology will fit every signals into your eyes.
English - 3
BN68-00718T-00Eng_1007
10/13/04
9:28 AM
Page 4
Contents
◆ FOREWORD
■
User Instructions............................................................................................
2
◆ CONNECTING AND PREPARING YOUR DISPLAY
■
■
■
■
■
■
■
■
■
■
■
■
■
Your New Plasma Display Panel...................................................................
Infrared Remote Control ................................................................................
Inserting the Batteries in the Remote Control................................................
Assembling the Stand-Base ..........................................................................
Installing the Display on the Wall Attachment Panel .....................................
Connecting to an Aerial or Cable Television Network ...................................
Connecting a Satellite Receiver or Decoder..................................................
Switching On and Off.....................................................................................
Placing in Standby Mode...............................................................................
Becoming Familiar with the Remote Control .................................................
Setting Up Your Remote Control ...................................................................
Plug & Play Feature.......................................................................................
Choosing Your Language..............................................................................
6
8
9
9
10
12
12
13
13
14
15
16
17
◆ SETTING THE CHANNELS
■
■
■
■
■
■
■
■
Storing Channels Automatically.....................................................................
Storing Channels Manually............................................................................
Skipping Unwanted Channels .......................................................................
Sorting the Stored Channels .........................................................................
Assigning Names to Channels ......................................................................
Using the LNA (Low Noise Amplifier) Feature...............................................
Activating the Child Lock ...............................................................................
Displaying Information ...................................................................................
18
19
21
22
23
24
25
26
◆ USING YOUR DISPLAY
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
Changing the Picture Standard .....................................................................
Adjusting the Picture Settings........................................................................
Adjusting the Picture Settings (PC or DVI Mode) ..........................................
Setting the Picture (PC Mode).......................................................................
Using the Fine Tune ......................................................................................
Viewing the Channel Scan Picture ................................................................
Freezing the Current Picture .........................................................................
Selecting the Picture Size..............................................................................
Selecting the Film Mode ................................................................................
DNIeTM (Digital Natural Image engine)
...............................................
Setting the My Colour Control (Easy Control) ...............................................
Setting the My Colour Control (Detail Control) ..............................................
Setting the Blue Screen.................................................................................
Setting the Melody Sound .............................................................................
Using the Colour Weakness Enhancement Feature..........................................
Viewing the Picture In Picture (PIP) ..............................................................
English - 4
26
27
28
29
31
32
32
33
34
34
35
36
37
37
38
39
BN68-00718T-00Eng_1007
10/13/04
9:28 AM
Page 5
Contents (continued)
◆ USING YOUR DISPLAY (continued)
■
■
■
■
■
■
■
■
■
■
■
■
■
■
Using the Digital NR (Noise Reduction) Feature ...........................................
Selecting the Fan...........................................................................................
Protecting the Screen Burning.......................................................................
Changing the Sound Standard ......................................................................
Adjusting the Sound Settings ........................................................................
Adjusting the Volume Automatically ..............................................................
Setting the TruSurround XT...........................................................................
Selecting the Internal mute............................................................................
Selecting the Sound Mode (depending on the model) ..................................
Setting the Sleep Timer .................................................................................
Setting and Displaying the Current Time.......................................................
Switching the Television On and Off Automatically .......................................
Viewing an External Signal Source ...............................................................
Redirecting an Input to the External Output ..................................................
41
41
42
43
44
44
45
45
46
47
48
49
50
51
◆ USING THE TELETEXT FEATURE
■
■
■
■
Teletext Feature ............................................................................................
Displaying the Teletext Information ...............................................................
Selecting Display Options..............................................................................
Selecting a Teletext Page..............................................................................
52
52
53
54
◆ ADDITIONAL INFORMATION AND CONNECTIONS
■
■
■
■
■
■
■
■
■
■
Connecting to the External Devices ..............................................................
Connecting to the S-Video Input....................................................................
Connecting to the DVI Input ..........................................................................
Connecting to the PC Input ...........................................................................
Connecting to the Component Input..............................................................
Connecting and Using the Home Theater System ........................................
How to Install Speakers.................................................................................
Setting up Your PC Software (Windows only) ...............................................
Input Mode (PC/DVI) .....................................................................................
Pin Configurations .........................................................................................
55
56
57
57
58
59
60
62
63
64
◆ RECOMMENDATIONS FOR USE
■
■
Troubleshooting: Before Contacting Service Personnel................................
Programming the Remote Control for Other Components ............................
Symbols
Press
☛
Important
65
66
➢
Note
English - 5
BN68-00718T-00Eng_1007
10/14/04
10:13 AM
Page 6
Your New Plasma Display Panel
➢
The actual configuration on your PDP may be different,
depending on your model.
Front Panel
Touch button
Touch the right side of each
button name using your finger
to operate the button.
a) SOURCE
External input selection.
b) MENU
Menu display.
c) -
+
Volume adjustment.
Also used to select or adjust items on the
on-screen menu.
d)
C/P.
Channel selection. Auto power On.
Also used to move up or down in the
on-screen menu.
e)
Confirm your choice (Store or Enter).
English - 6
f) I /
Press to turn the PDP on and off.
Power Indicator
- Power Off: Red
- Power On: Off
- Timer On: Green
g) Remote Control Signal Receiver
Aim the remote control towards this
spot on the PDP.
BN68-00718T-00Eng_1007
10/13/04
9:28 AM
Page 7
Your New Plasma Display Panel (continued)
➢
The actual configuration on your PDP may be different,
depending on your model.
Side of the TV
S-Video Input
Video Input
Audio Input (L, R)
Rear Panel
➢
For further details about connection, refer to pages 55~59.
a) DVI INPUT (DVI-D / L-AUDIO-R)
Connect to the digital video and audio
output jack for device with DVI output.
g) AV1, AV2, AV3
(VIDEO / L-AUDIO-R)
Video and audio inputs for external devices, such
as a camcorder or VCR.
b) MONITOR OUT (VIDEO / L-AUDIO-R)
Outputs for external devices.
c) Ext.1, Ext.2, Ext.3
Inputs or outputs for external devices, such as
VCR, DVD, video game device or video disc
players.
d) PC INPUT (RGB / AUDIO)
Connect to the video and audio output jack on
your PC.
h) COMPONENT1, COMPONENT2
Video (Y/Pb/Pr) and audio (L-AUDIO-R) inputs for
Component.
i) ANT IN VHF/UHF (75Ω)
75Ω Coaxial connector for Aerial/Cable Network.
j) EXT SPEAKER (8Ω)
Connectors for external rear speakers.
k) POWER IN
e) ONLY FOR SERVICE
Connect the supplied power cord.
Connector for service only.
f) S-VIDEO1, S-VIDEO2
(S-VIDEO1 or S-VIDEO2 / L-AUDIO-R)
Video and audio inputs for external devices with
an S-Video output, such as a camcorder or VCR.
English - 7
BN68-00718T-00Eng_1007
10/13/04
9:28 AM
Page 8
Infrared Remote Control
TURNS THE PDP ON AND OFF
WHEN YOU PRESS A BUTTON , ‘
’
APPEARS ALONG WITH SELECTED MODE
(TV, VCR, CATV, DVD, OR STB) AND
REMAINING BATTERIES ON LCD
PICTURE EFFECT SELECTION
SOUND EFFECT SELECTION
TELETEXT CANCEL
MAKE THE REMOTE CONTROL WORKS
FOR TV, VCR, CATV, DVD PLAYER, OR
STB
DIRECT CHANNEL SELECTION
AUTOMATIC SWITCH-OFF/
TELETEXT SUB-PAGE
PICTURE SIZE/
TELETEXT SIZE SELECTION
VOLUME INCREASE
TEMPORARY SOUND SWITCH-OFF
VOLUME DECREASE
TELETEXT DISPLAY/
MIX BOTH TELETEXT INFORMATION
AND THE NORMAL BROADCAST
MENU DISPLAY/
TELETEXT INDEX
NEXT CHANNEL/
TELETEXT NEXT PAGE/
EXTERNAL INPUT SELECTION/
TELETEXT PAGE HOLD
PREVIOUS CHANNEL/
TELETEXT PREVIOUS PAGE/
INFORMATION DISPLAY
TV MODE SELECTION
EXIT TELETEXT
(DEPENDING ON THE MODEL)
MOVE TO THE REQUIRED
MENU OPTION/
ADJUST AN OPTION VALUE
RESPECTIVELY
PICTURE STILL
DNIe ON/DEMO/OFF
FASTEXT TOPIC SELECTION
REMOTE CONTROL SETUP
IF YOUR REMOTE CONTROL IS NOT
FUNCTIONING PROPERLY, TAKE
OUT THE BATTERIES AND PRESS
THE RESET BUTTON FOR ABOUT
2~3 SECONDS. RE-INSERT THE
BATTERIES AND TRY USING THE
REMOTE CONTROL AGAIN.
➢
English - 8
CONFIRM YOUR CHOICE
(STORE OR ENTER)
SOUND MODE SELECTION
TruSurround XT
MODE SELECTION
PIP FUNCTIONS:
- PIP ACTIVATING OR DEACTIVATING
(PIP ON)
- SWAPPING THE MAIN AND THE SUB
PICTURE (SWAP)
- LOCATION SELECTION (POSITION)
- SOURCE SELECTION (SOURCE)
- SIZE SELECTION (SIZE)
- SCAN
- SELECTING THE CHANNEL OF SUB
PICTURE (P
)
VCR/DVD FUNCTIONS:
- REWIND (REW)
- STOP
- PLAY/PAUSE
- FAST FORWARD (FF)
The performance of the remote control may be affected by bright light.
BN68-00718T-00Eng_1007
10/14/04
10:16 AM
Page 9
Inserting the Batteries in the Remote Control
You must insert or replace the batteries in the remote control when
you:
◆ Purchase the PDP
◆ Find that the remote control is no longer operating
correctly
1
Remove the cover on the rear of the remote control by pressing
the symbol ( ) downwards and then pulling firmly to remove it.
2
Insert two R03, UM4, “AAA” 1.5V or equivalent batteries taking
care to respect the polarities:
◆ - on the battery against - on the remote control
◆ + on the battery against + on the remote control
3
Replace the cover by aligning it with the base of the remote
control and pressing it back into place.
Do not mix battery types, i.e. alkaline and manganese.
Assembling the Stand-Base
1
Assemble two support pins with the stand base and firmly secure
both sides of the support pins using 8 screws provided.
2
Assemble the PDP with the stand and firmly secure the PDP using
4 screws provided.
➢
◆ Two or more people should carry the PDP. Never lay the
PDP on the floor because of possible damage to the screen.
Always store the PDP upright.
(depending on your model)
The angle of the PDP can be up to 15
degrees left/right.
English - 9
BN68-00718T-00Eng_1007
10/13/04
9:28 AM
Page 10
Installing the Display on the Wall Attachment Panel
Installation Notes
◆ Do not install the PDP on any place other than vertical walls.
◆ To protect the performance of the PDP and prevent troubles, avoid the followings:
- Do not install next to smoke and fire detectors.
- Do not install in an area subjected to vibration or high voltage.
- Do not install near or around any heating apparatus.
◆ Use only recommended parts and components.
Mounting Kits (Sold Separately)
Wall Mount Bracket
Plastic Hanger
Screws
4 EA
4 EA
How to Adjust Mounting Angle
(depending on your model)
The wall mount bracket is delivered
separately. Please tighten the captive
screw in the direction of the arrow after
assembling the bracket.
English - 10
1
Secure the PDP to the wall mount bracket.
(Please refer to the following instructions.)
2
Set the angle by pulling the upper end of the
PDP attached to bracket in the direction of the
arrow.
3
The angle can be adjusted from 0° to 15° by
±2°.
BN68-00718T-00Eng_1007
10/13/04
9:28 AM
Page 11
Installing the Display on the Wall Attachment Panel (continued)
➢ The exterior of the PDP may be different than the picture.
(Assembly and installation of the plastic hanger is the same.)
1
Remove the screws from the back of the PDP.
2
Use the screws and assemble the plastic
hanger.
☛
◆ Please ask the installers to install the
wall mount bracket.
◆ Please be sure to check if the plastic
hanger is completely secured on both
the left and right side after hanging
the PDP on the wall mount bracket.
◆ Please avoid catching your fingers
while installing and adjusting the
angle.
◆ Please tightly secure the wall mount
bracket to the wall to avoid injury
from a falling PDP.
3
Tighten the screws of the plastic hanger to the
back side of the PDP.
4
Put the 4 pegs on the PDP in the grooves of the wall mount bracket and pull down on the PDP (!) to
secure it to the wall mount bracket (@). Tighten the screws as shown (#) so that the PDP cannot be
separated from wall mount bracket.
PDP panel
Wall attachment panel bracket
Wall
Connecting External Devices to the PDP
◆ To connect external devices such as a DVD or a Home Theater System to the PDP, please refer
to following instructions:
1
Be sure to remove the safety pins underneath the PDP.
◆ If the safety pins are not removed, the angle cannot be adjusted.
Any attempt to do so may cause damage to the PDP.
2
Pull out the bottom of the PDP (which has been attached to the Wall
Mount Bracket) in the direction indicated by the arrows (refer to
the illustration) until it clicks.
◆ Using the PDP After Connecting External Devices.
Be sure to secure the PDP by inserting the 2 safety pins after
o
readjusting the angle of the PDP to 0 .
◆ For safety, be sure to secure the PDP using the safety pins.
If the safety pins are not used, the PDP may fall, causing serious
injury.
English - 11
BN68-00718T-00Eng_1007
10/13/04
9:28 AM
Page 12
Connecting to an Aerial or Cable Television Network
To view television channels correctly, a signal must be received by
the set from one of the following sources:
◆ An outdoor aerial
◆ A cable television network
◆ A satellite network
Rear of the PDP
1
In the first three cases, connect the aerial or network input cable to
the ANT IN jack on the rear of the PDP.
2
If you are using an indoor aerial, you may need to turn it when
tuning your PDP until you obtain a picture that is both sharp and
clear.
For further details, refer to:
◆ “Storing Channels Automatically” on page 18
◆ “Storing Channels Manually” on page 19
or
Cable Television
Network
➢
When installing or re-installing your PDP, be sure to use the
supplied coaxial antenna cable. If you connect using a different
coaxial cable, there is risk of noise or interference to the screen
image. (You must not use another general purpose cable.
Use the 3M/5M/7M cable supplied by Samsung.)
Connecting a Satellite Receiver or Decoder
Rear of the PDP
or
In order to watch television programmes broadcast via a satellite
network, you must connect a satellite receiver to the rear of the
PDP. Also, in order to descramble a coded transmission signal, you
must connect a decoder to the rear of the PDP.
Using a Coaxial cable
Connect a coaxial cable to the:
◆ Receiver (or Decoder) output socket.
◆ Television aerial input socket.
➢
If you wish to connect both a satellite receiver (or decoder)
and a VCR, you should connect the:
◆ Receiver (or Decoder) to the VCR
◆ VCR to the PDP
Otherwise, connect the receiver (or decoder) directly to the
PDP.
Satellite receiver/
Decoder
English - 12
BN68-00718T-00Eng_1007
10/13/04
9:28 AM
Page 13
Switching On and Off
The mains lead is attached to the rear of your PDP.
1
Plug the mains lead into an appropriate socket.
Result:
➢
2
The main voltage is indicated on the rear of the PDP and
the frequency is 50 or 60Hz.
Press the “ I / ” button on the front of the PDP (or POWER (
button on the remote control) to switch the PDP on.
Result:
➢
3
Front of the PDP
The Standby indicator on the front of the PDP lights up.
)
The programme that you were watching last is
re-selected automatically.
If you have not yet stored any channels, no clear picture
appears. Refer to “Storing Channels Automatically” on page
18 or “Storing Channels Manually” on page 19.
To switch your PDP off, press the “ I /
TV
” button again.
Placing in Standby Mode
Your PDP can be placed in Standby mode, in order to reduce the
Power consumption.
The Standby mode can be useful when you wish to interrupt
viewing temporarily (during a meal, for example).
1
Press the POWER (
Result:
2
) button on the remote control.
The screen is turned off and the Standby indicator on
the front of the PDP lights.
To switch the PDP back on, simply press the POWER (
again or a numeric button.
➢
TV
You can also switch on by pressing the P
or
) button
button.
English - 13
BN68-00718T-00Eng_1007
10/13/04
9:28 AM
Page 14
Becoming Familiar with the Remote Control
The remote control is used mainly to:
◆ Change channels and adjust the volume
◆ Display the on-screen menu system
The following table presents the most frequently used buttons and
their functions.
Button
to
SLEEP
Menu Function
Used to display the next
stored channel.
-
Used to display the
previous stored channel.
-
Used to display the corresponding channels.
➢ For double digit channels, the second digit must be
pushed immediately after the first. Failure to do this will
result in a single digit channel being displayed.
Used to select a preset time interval (off - 30 - 60 - 90 - 120 150-180).
Used to increase the
volume.
-
Used to decrease the
volume.
-
MUTE
Used to switch the sound off temporarily.
➢ To turn the sound back on, press this button again, or
press the
or
button.
MENU
Used to display the
on-screen menu system.
Used to return to the previous
menu or normal viewing.
-
Used to:
◆ Display a submenu
containing selections for
the current menu option
◆ Increase/decrease a
menu option value
-
Used to confirm your choice.
-
Used to exit from the menu
system and return to normal
viewing directly.
EXIT/TV
English - 14
Viewing Function
BN68-00718T-00Eng_1007
10/13/04
9:28 AM
Page 15
Setting Up Your Remote Control
This PDP’s remote control can operate VCR, Cable box(CATV),
DVD, or Set-top box(STB), in addition to controlling the PDP.
➢
The remote control is not compatible with the TV
manufactured by another company.
1
Turn off your VCR, Cable box(CATV), DVD, or STB.
2
Press the SELECT button.
Mode is changed whenever SELECT button is pressed.
3
Press the POWER ( ) button on the remote control.
The component you select should turn on. If it turns on,
your remote control is now set correctly.
4
Once your remote control is set up, press the SELECT button any
time you want to use the remote control to operate your VCR,
Cable box(CATV), DVD, or STB.
➢
➢
➢
➢
VCR
When your remote control is in the VCR, Cable box(CATV),
DVD, or STB mode, the volume buttons still control your
television’s volume.
To program the cable receiver controls:
◆ Press the SELECT button to select CATV.
◆ Point the remote control at the cable receiver and press
the SET button. Then press the company code number(s)
for the component in page 66.
Ex) If the component is manufactured by Oak, press 026.
To program the VCR controls:
◆ Press the SELECT button to select VCR
◆ Point the remote control at the VCR and press the SET
button. Then press the company code number(s) for the
component in page 67.
To program the DVD controls:
◆ Press the SELECT button to select DVD
◆ Point the remote control at the DVD and press the SET
button. Then press the company code number(s) for the
component in page 66.
English - 15
BN68-00718T-00Eng_1007
10/13/04
9:28 AM
Page 16
Plug & Play Feature
Plug & Play
Press ENTER to Start Plug & Play
When the television is initially powered on, several basic customer
settings proceed automatically and subsequently. The following
settings are available.
Start
Enter
Exit
1
Language
Result:
Move
3
Press the ENTER (
Result:
6
Press the ENTER (
Enter
➢
Auto Store
➢
Press ENTER to start channel memory
40 MHz
0%
Enter
57 MHz
1%
Stop
Enter
Stop
Clock
Hour
Min
01
00
Move
Stop
Enjoy Your Watching
English - 16
The Auto Store menu is displayed.
) button.
The search will end automatically. Channels are sorted
and stored in an order which reflects their position in
the frequency range (with lowest first and highest last).
When it has finished, the Clock Set menu is displayed.
To stop the search before it has finished or return to normal
viewing, press the MENU (
) button.
Press the ENTER (
) button to set the clock.
8
Press the œ or √ button to move to the hour or minute.
Set the hour or minute by pressing the … or † button.
9
When it has finished, the message Enjoy Your Watching is
displayed, and then the channel which has been stored will be
activated.
Stop
Auto Store
Channel store in process.
) button to confirm your choice.
To start the search, press the ENTER (
Result:
Start
The Country menu is displayed.
Select your country by pressing the … or † button.
7
Move
The message Antenna input check is displayed.
5
Result:
Austria
Belgium
Croatia
Denmark
Finland
France
Germany
▼ More
) button to confirm your choice.
Make sure that the antenna is connected to the TV, and then
press the ENTER (
) button.
Result:
Antenna Input Check
Country
The message Plug & Play is displayed, and then the
Language menu is automatically displayed a few
seconds later.
Select the appropriate language by pressing the … or † button.
4
Country
) button
2
Enter
Plug & Play
Adjust
If the television is in standby mode, press the POWER (
on the remote control.
BN68-00718T-00Eng_1007
10/13/04
9:28 AM
Page 17
Plug & Play Feature (continued)
If you want to reset this feature...
TV
1
Press the MENU (
) button.
The main menu is displayed.
Result:
2
Press the … or † button to select Setup.
The options available in the Setup group are displayed.
Result:
3
Press the ENTER (
4
Press the … or † button to select Miscellaneous.
Press the ENTER (
) button.
The options available in the Miscellaneous group are
Result:
displayed.
5
6
) button.
Move
Enter
TV
√
√
√
√
√
√
√
√
Return
Miscellaneous
Melody
√
: Off
√
Plug & Play
Press the … or † button to select Plug & Play.
Press the ENTER (
) button.
Result:
Setup
Time
Language
: English
AV Setup
Digital NR
: On
Miscellaneous
PC Setup
Colour Weakness: Off
Burn Protection
Blue Screen
: Off
√
Fan
: On
√
The message Plug & Play is displayed.
For further details on how to set, refer to the opposite page.
Move
Enter
Return
Choosing Your Language
When you start using your television for the first time, you must
select the language which will be used for displaying menus and
indications.
TV
1
Press the MENU (
) button.
The main menu is displayed.
Result:
2
Press the … or † button to select Setup.
The options available in the Setup group are displayed.
Result:
3
Press the ENTER (
4
Press the … or † button to select Language.
Press the ENTER (
) button.
The available languages are listed.
Result:
Move
) button.
5
Select the appropriate language by pressing the … or † button.
6
Press the ENTER (
7
When you are satisfied with your choice, press the EXIT/TV (
button to return to normal viewing.
Setup
Time
Language
: English
AV Setup
Digital NR
: On
Miscellaneous
PC Setup
Colour Weakness: Off
Burn Protection
Enter
TV
) button to confirm your choice.
)
√
√
√
√
√
√
√
√
Return
Setup
Time
Language
: English
AV Setup
Digital NR
: On
Miscellaneous
PC Setup
Colour Weakness: Off
Burn Protection
Move
Enter
English - 17
Return
√
√
BN68-00718T-00Eng_1007
10/13/04
9:28 AM
Page 18
Storing Channels Automatically
TV
Channel
Country
: Austria
√
Auto Store
√
Manual Store
√
Edit
√
Fine Tune
√
Ch. Scan
√
You can scan for the frequency ranges available to you, (availability
depends on your country). Automatically allocated programme
numbers may not correspond to actual or desired programme
numbers. However you can sort numbers manually and clear any
channels you do not wish to watch.
1
Press the MENU (
Result:
Move
Enter
Auto Store
Manual Store
Edit
Fine Tune
Ch. Scan
Press the … or † button to select Channel.
Result:
Channel
Country
: Austria
Austria
Belgium
Croatia
Denmark
Finland
France
Press the ENTER (
4
Press the … or † button to select Country.
Press the ENTER (
) button.
) button.
†
Enter
TV
Return
: Austria
Select your country (or area) by pressing the … or † button.
➢ If you have selected the Others option but do not wish to
scan the PAL frequency range, store the channels manually
(see page 19).
6
Press the ENTER (
7
Press the … or † button to select Auto Store.
Press the ENTER (
) button.
√
Auto Store
√
Manual Store
√
Edit
√
Fine Tune
√
Ch. Scan
√
Result:
Enter
The countries available are listed.
5
Channel
Country
Move
The options available in the Channel group are
displayed.
3
Result:
Move
The main menu is displayed.
Return
2
TV
) button.
) button to confirm your choice.
The Auto Store menu is displayed.
Return
8
Press the ENTER (
Result:
Auto Store
Channel store in process.
57 MHz
1%
Stop
Enter
➢
Return
9
English - 18
) button to start the search.
The search will end automatically. Channels are sorted
and stored in an order which reflects their position in
the frequency range, (with lowest first and highest last).
The programme originally selected is then displayed.
To stop the search before it has finished, press the
MENU (
) button.
When the channels have been stored, you can:
◆ Sort them in the order required (see page 22)
◆ Clear a channel (see page 21)
◆ Fine-tune channel reception if necessary (see page 31)
◆ Assign a name to the stored channels (see page 23)
◆ Activate/deactivate the Digital NR (Noise Reduction) feature
(see page 41)
BN68-00718T-00Eng_1007
10/13/04
9:28 AM
Page 19
Storing Channels Manually
You can store up to 100 television channels, including those
received via cable networks.
TV
Channel
Country
When storing channels manually, you can choose:
◆ Whether or not to store each of the channels found
◆ The programme number of each stored channel which
you wish to identify
1
Result:
2
Result:
The options available in the Channel group are
displayed.
Press the ENTER (
4
Press the … or † button to select Manual Store.
Press the ENTER (
) button.
Result:
6
) button.
The option available in the Manual Store group are
displayed with Prog. is selected.
To assign a programme number to a channel, find the correct
number by pressing the … or † button.
If necessary, select the broadcasting standard required.
Press the œ or √ button to select Colour System and press
the … or † button. The colour standards are displayed in the
following order. (depending on the model.)
Auto - PAL - SECAM or
Auto - NT3.58 - NT4.43 - PAL60
7
√
Edit
√
Fine Tune
√
Ch. Scan
√
The main menu is displayed.
3
5
√
Enter
Return
) button.
Press the … or † button to select Channel.
Press the œ or √ button to select Sound System and press the
… or † button. The sound standards are displayed in the following
order. (depending on the model.)
√
Manual Store
Move
Press the MENU (
: Austria
Auto Store
Manual Store
Prog.
Colour
System
Sound
System
9
Auto
BG
Channel
Search
Store
C --
245MHz
?
Adjust
Return
√ Move
Manual Store
Prog.
Colour
System
Sound
System
9
Auto
BG
Channel
Search
Store
C --
245MHz
?
Adjust
Return
œ √ Move
Manual Store
Prog.
Colour
System
Sound
System
9
Auto
BG
Channel
Search
Store
C 00
245MHz
?
Adjust
Return
œ √ Move
BG - DK - I - L
English - 19
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 20
Storing Channels Manually (continued)
8
Manual Store
Prog.
Colour
System
Sound
System
9
Auto
BG
Channel
Search
Store
C --
245MHz
?
Adjust
Return
œ √ Move
◆ Press the œ or √ button to select Channel.
◆ Press the … or † button to select C (Air channel) or S (Cable
channel).
◆ Press the √ button.
◆ Press the numeric buttons (0~9), … or † button to indicate
the desired channel number.
➢
Manual Store
Prog.
Colour
System
Sound
System
9
Auto
BG
Channel
Search
Store
C 15
245MHz
?
Adjust
Return
œ √ Move
9
Colour
System
Sound
System
9
Auto
BG
Channel
Search
Store
C 15
245MHz
?
Adjust
Return
œ √ Move
If there is no sound or noise only, try a different sound
standard.
If you do not know the channel numbers, select the Search by
pressing the œ or √ button. Press the … or † button to start the
search.
Result:
Manual Store
Prog.
If you know the number of the channel to be stored, see the
following steps.
The tuner scans the frequency range until the first
channel or the channel that you selected is received on
your screen.
10
To assign a programme number to a channel, select the Prog.
by pressing the œ or √ button. Press the … or † button until you
find the correct number.
11
To store the channel and associated programme number, select
the Store by pressing the œ or √ button.
Press the ENTER (
) button.
12
Repeat Steps 8 to 11 for each channel to be stored.
Manual Store
Prog.
Colour
System
Sound
System
9
Auto
BG
Channel
Search
Store
C 15
245MHz
OK
œ √ Move
Enter
Return
☛
Channel mode
◆ P (Programme mode): When completing tuning, the
broadcasting stations in your area have been assigned to
position numbers from P00 to P99. You can select a
channel by entering the position number in this mode.
◆ C (Real channel mode): You can select a channel by entering
the assigned number to each air broadcasting station in this
mode.
◆ S (Cable channel mode): You can select a channel by entering
the assigned number for each cable channel in this mode.
English - 20
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 21
Skipping Unwanted Channels
◆ Skipping unwanted channels
You can exclude the channels of your choice from the channel
scan operation. When you scan through the stored channels,
those that you have chosen to skip are thus not displayed.
All channels that you do not specifically choose to skip are
displayed during scanning.
1
Press the MENU (
Result:
2
Channel
Country
: Austria
√
Manual Store
√
Edit
√
Fine Tune
√
Ch. Scan
√
Move
Enter
TV
The options available in the Channel group are
displayed.
Return
Edit
Add/Delete
√
Sort
√
√
Name
3
Press the ENTER (
) button.
LNA
√
: Off
√
Child Lock
4
Press the … or † button to select Edit.
Press the ENTER (
) button.
Result:
5
Move
The Edit menu is displayed.
Press the … or † button to select Add/Delete.
Press the ENTER (
) button.
Result:
√
Auto Store
) button.
The main menu is displayed.
Press the … or † button to select Channel.
Result:
TV
TV
Press the … or † button to select the channel to be deleted.
Press the ENTER (
) button.
7
To add or delete the channel, select Added or Deleted by
pressing the … or † button.
Press the ENTER (
) button to confirm.
Return
Add/Delete
The Add/Delete menu is displayed with the current
channel automatically is selected.
6
Enter
Prog.
1
2
3
4
5
✽
✽
✽
✽
✽
Added
Deleted
Deleted
Deleted
Deleted
Enter
Return
---------------------
Move
TV
Add/Delete
Prog.
1
2
3
4
5
Adjust
✽
✽
✽
✽
✽
Added
Deleted
Deleted
Deleted
Deleted
Enter
Return
---------------------
English - 21
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 22
Sorting the Stored Channels
TV
This operation allows you to change the programme numbers of
stored channels. This operation may be necessary after using ATM.
You can delete those channels you do not want to keep.
Channel
Country
: Austria
√
Auto Store
√
Manual Store
√
Edit
√
Fine Tune
√
Ch. Scan
√
1
Result:
2
Move
Enter
TV
Return
Edit
√
Sort
√
Name
√
4
Press the … or † button to select Edit.
Press the ENTER (
) button.
Result:
√
Enter
Return
Sort
---------------------
Move
✽
✽
✽
✽
✽
7
Select the number of the programme to which the channel is to
be moved by pressing the … or † button.
Press the ENTER (
) button.
Return
8
TV
Sort
Prog.
2
3
4
5
6
Move
---------------------
✽
✽
✽
✽
✽
Enter
English - 22
----- ✽
Return
The Sort menu is displayed.
Select the channel that you wish to move by pressing the … or †
button. Press the ENTER (
) button.
Result:
Enter
The Edit menu is displayed.
6
Prog.
2
3
4
5
6
) button.
Press the … or † button to select Sort.
Press the ENTER (
) button.
Result:
TV
The options available in the Channel group are
displayed.
Press the ENTER (
5
Move
The main menu is displayed.
3
√
: Off
Child Lock
) button.
Press the … or † button to select Channel.
Result:
Add/Delete
LNA
Press the MENU (
The channel is moved to its new position and all other
channels are shifted accordingly.
Repeat Steps 6 to 7 until you have moved all the channels to the
required programme numbers.
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 23
Assigning Names to Channels
Channel names will be assigned automatically when channel
information is broadcast. These names can be changed, allowing
you to assign new names.
1
Press the MENU (
Result:
2
4
√
Edit
√
Fine Tune
√
Ch. Scan
√
) button.
Enter
TV
Return
Edit
√
Press the … or † button to select Edit.
Press the ENTER (
) button.
Sort
√
Result:
Child Lock
LNA
The Edit menu is displayed.
The Name menu is displayed with the current channel
automatically is selected.
√
Enter
Return
Name
TV
Prog.
2
3
4
5
6
Arrow indications are displayed around the name box.
Press the … or † button to select a letter (A~Z), a number (0~9),
or a symbol (space, ., -). Move on to the previous or next letter by
pressing the œ or √ button.
√
: Off
Move
If necessary, select the channel to be assigned to a new name by
pressing the … or † button. Press the ENTER (
) button.
Preset steps 6 to 7 for each channel to be assigned to a new
name.
√
Name
Press the … or † button to select Name.
Press the ENTER (
) button.
Result:
9
√
Manual Store
Add/Delete
Result:
8
√
: Austria
Auto Store
Move
The options available in the Channel group are
displayed.
Press the ENTER (
7
) button.
The main menu is displayed.
3
6
Channel
Country
Press the … or † button to select Channel.
Result:
5
TV
Name
✽
✽
✽
✽
✽
---------------------
Move
Enter
TV
Return
Name
When you have finished entering the name, press the ENTER
(
) button to confirm the name.
Prog.
2
3
4
5
6
Adjust
Name
---------------------
Move
English - 23
✽
✽
----✽
✽
Return
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 24
Using the LNA (Low Noise Amplifier) Feature
TV
Channel
Country
: Austria
√
Auto Store
√
Manual Store
√
Edit
√
Fine Tune
√
Ch. Scan
√
This function is very useful in the situation that the TV is used in
weak signal. LNA amplifies the TV signal in the weak signal area,
but not noise.
1
2
Move
Enter
TV
Return
Edit
√
Sort
√
Name
√
Press the ENTER (
4
Press the … or † button to select Edit.
Press the ENTER (
) button.
Result:
√
5
Move
Enter
Return
Edit
6
Add/Delete
Sort
) button.
The Edit menu is displayed.
Press the … or † button to select LNA.
Press the ENTER (
) button.
Result:
TV
The options available in the Channel group are
displayed.
3
√
: Off
Child Lock
) button.
The main menu is displayed.
Press the … or † button to select Channel.
Result:
Add/Delete
LNA
Press the MENU (
Result:
The available options are listed.
Select On or Off by pressing the … or † button.
Press the ENTER (
) button to confirm.
Name
LNA
: Off Off
Child Lock
Move
Enter
English - 24
On
Return
➢
◆ If the picture is noisy with the LNA set to On, select Off.
◆ LNA setting is to be made for each channel.
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 25
Activating the Child Lock
◆ Activating the child lock
This feature allows you to lock the television so that it cannot be
switched on via the front panel. It can, however, still be switched
on via the remote control. Thus, by keeping the remote control
away from unauthorised users, such as children, you can prevent
them from watching unsuitable programme.
1
Press the MENU (
Result:
2
Channel
Country
: Austria
√
Manual Store
√
Edit
√
Fine Tune
√
Ch. Scan
√
Move
Enter
TV
The options available in the Channel group are
displayed.
Return
Edit
Add/Delete
√
Sort
√
√
Name
3
Press the ENTER (
) button.
LNA
√
: Off
√
Child Lock
4
Press the … or † button to select Edit.
Press the ENTER (
) button.
Result:
5
Move
The Edit menu is displayed.
Press the … or † button to select Child Lock.
Press the ENTER (
) button.
Result:
√
Auto Store
) button.
The main menu is displayed.
Press the … or † button to select Channel.
Result:
TV
Press the … or † button to select the channel to be locked.
7
Press the ENTER ( ) button. To lock the channel, select
Locked by pressing the … or † button (to unlock the channel,
select Unlocked). Press the ENTER ( ) button to confirm.
Return
Child Lock
TV
The Child Lock menu is displayed with the current
channel automatically is selected.
Blue Screen is displayed when the Child Lock is
activated.
6
Enter
Prog.
2
3
4
5
6
---------------------
Move
✽
✽
✽
✽
✽
Enter
Unlocked
Unlocked
Unlocked
Unlocked
Unlocked
Return
Child Lock
TV
Prog.
2
3
4
5
6
Adjust
---------------------
✽
✽
✽
✽
✽
Enter
English - 25
Unlocked
Unlocked
Unlocked
Unlocked
Unlocked
Return
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 26
Displaying Information
You can view the channel information and setting status you select
by pressing the “INFO (
)” button on the remote control.
The information displayed varies according to the selected source.
Mono
P1 ✽
Picture
Sound
07 : 05
: Dynamic
: Custom
Changing the Picture Standard
TV
You can select the type of picture which best corresponds to your
viewing requirements.
Picture
Mode
Custom
Colour Tone
Colour Control
Film Mode
Size
PIP
† More
Move
: Dynamic
: Normal
: Off
: 16 : 9
Enter
TV
√
√
√
√
√
√
√
1
Press the MENU (
) button.
The main menu is displayed.
Result:
2
Press the … or † button to select Picture.
The options available in the Picture group are
Result:
displayed.
3
Press the ENTER (
) button.
The Mode is selected.
Result:
4
Press the ENTER (
) button again.
The options available are listed.
Result:
5
Select the option by pressing the … or † button.
The following modes are available depending on the
Result:
input source.
◆ Dynamic - Standard - Movie - Custom
◆ High - Middle - Low - Custom
(PC or DVI Mode).
6
Press the ENTER (
Return
Picture
Mode
Custom
Colour Tone
Colour Control
Film Mode
Size
PIP
† More
Move
: Dynamic
Dynamic
Standard
: Normal
Movie
Custom
: Off
: 16 : 9
Enter
Return
➢
English - 26
) button to confirm.
You can also set these options simply by pressing the
P.MODE (
: Picture Mode) button.
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 27
Adjusting the Picture Settings
Your television has several settings which allow you to control
picture quality.
1
Press the MENU (
Result:
2
TV
) button.
The main menu is displayed.
Press the … or † button to select Picture.
Result:
The options available in the Picture group are
displayed.
3
Press the ENTER (
4
Select the required option (Custom, Colour Tone) pressing the
… or † button.
5
Press the … or † button to select Custom.
Press the ENTER (
) button.
Result:
6
Move
) button.
: Normal
: Off
: 16 : 9
Return
Custom
Contrast
Brightness
Sharpness
Colour
Tint
G50
70
50
70
50
R50
The Custom menu is displayed.
Move
➢
Custom Options available in PC, DVI Mode: Contrast,
Brightness, or Sharpness.
➢
The horizontal bar is displayed. Move the horizontal bar’s
cursor left or right by pressing the œ or √ button.
➢
When the picture mode is set to Custom, the settings values
may vary depending on the input source.
(ex. RF, Video, Component, PC, or DVI)
➢
If you make any changes to these settings, the picture
standard is automatically switched to the Custom
When you are satisfied with the settings, press the EXIT/TV (
button to return to normal viewing.
Enter
Return
Contrast
70
TV
Picture
Mode
Custom
Colour Tone
Colour Control
Film Mode
Size
PIP
† More
Move
◆ Colour Tone : Cool2, Cool1, Normal, Warm1, or Warm2.
➢
√
√
√
√
√
√
√
: Dynamic
Enter
TV
Press the ENTER (
) button to change the setting.
The options are displayed in the following order.
◆ Custom : Contrast, Brightness, Sharpness, Colour, or
Tint(NTSC ONLY).
7
Picture
Mode
Custom
Colour Tone
Colour Control
Film Mode
Size
PIP
† More
: Dynamic
: Normal
Cool2
Cool1
: Off Normal
: 16 :Warm1
9
Enter
)
If you make any changes to these settings, the picture
standard is automatically switched to the Custom.
English - 27
Warm2
Return
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 28
Adjusting the Picture Settings (PC or DVI Mode)
➢
Preset to the PC or DVI mode by using the SOURCE button.
1
TV
Press the MENU (
Picture
Mode
Custom
Colour Tone
Colour Control
Film Mode
Size
PIP
† More
Move
: Colour1
: Off
: 16 : 9
Enter
TV
√
√
√
√
√
√
√
: Middle
Result:
2
Press the … or † button to select Picture.
Result:
Press the ENTER (
4
Press the … or † button to select Custom.
Press the ENTER (
) button.
Result:
80
50
50
50
R50
5
Enter
The Custom menu is displayed.
The horizontal bar is displayed. Move the horizontal
bar’s cursor left or right by pressing the œ or √ button.
Return
Picture
Move
) button.
Press the … or † button to select the option (Contrast,
Brightness, or Sharpness) to be adjusted.
Press the ENTER (
) button.
Result:
Mode
Custom
Colour Tone
Colour Control
Film Mode
Size
PIP
† More
The options available in the Picture group are
displayed.
3
Custom
TV
The main menu is displayed.
Return
Contrast
Brightness
Sharpness
Colour
Tint
G50
Move
) button.
6
Press the MENU (
) button to confirm your choice.
7
Press the MENU (
) button.
: Middle
Result:
: Normal
Custom
Colour1
: Off
Colour2
: 16 : 9
Colour3
Enter
The options available in the Picture group are
displayed again.
8
Press the † or … button to select Colour Tone.
Press the ENTER (
) button.
9
Select the option by pressing the … or † button.
The colour tones are displayed in the following order.
Return
Custom (PC mode only) - Colour1 - Colour2 - Colour3
TV
Colour Control
10
R
G
B
50
50
50
11
Move
Enter
100
English - 28
The Colour Control menu is displayed.
Press the … or † button to select the option (R, G, or B) to be
adjusted. Press the ENTER (
) button.
Result:
➢
) button.
The options available in the Picture group are
displayed again.
Press the … or † button to select Colour Control.
Press the ENTER (
) button.
Result:
Return
12
R
Press the MENU (
Result:
The horizontal bar is displayed. Move the horizontal
bar’s cursor left or right by pressing the œ or √ button.
The Colour Control is not available in the DVI Mode.
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 29
Setting the Picture (PC Mode)
➢
1
Preset to the PC mode by using the SOURCE button.
Press the MENU (
) button.
TV
Result:
2
Setup
The main menu is displayed.
Press the … or † button to select Setup.
Result:
The options available in the Setup group are
displayed.
3
Press the ENTER (
4
Press the … or † button to select PC Setup.
Press the ENTER (
) button.
) button.
Move
Result:
5
Enter
TV
Image Lock
√
Position
√
Information
√
Auto Adjustment
√
The options available in the Image Lock group are
displayed.
Move
6
Press the … or † button to select the option (Coarse, Fine) to be
adjusted. Press the ENTER (
) button.
Result:
Press the MENU (
) button to confirm your choice
8
Press the MENU (
) button.
9
Result:
10
11
The options available in the PC Setup group are
displayed again.
Press the … or † button to select Position.
Press the ENTER (
) button.
Enter
TV
Return
Image Lock
The horizontal bar is displayed. Move the horizontal
bar’s cursor left or right by pressing the œ or √ button.
7
Result:
Return
PC Setup
The options available in the PC Setup group are
displayed.
Press the … or † button to select Image Lock.
Press the ENTER (
) button.
Result:
√
√
√
√
√
√
√
√
Time
Language
: English
AV Setup
Digital NR
: On
Miscellaneous
PC Setup
Colour Weakness: Off
Burn Protection
Coarse
50
Fine
20
Move
Enter
Return
Coarse
50
The options available in the Position group are
displayed.
Adjust the position by using the …, †, œ, or √ button.
Press the MENU (
TV
) button to confirm your choice
PC Setup
Image Lock
√
Position
√
Information
√
Auto Adjustment
√
Move
Enter
TV
Return
Position
Move
œ √ Move
English - 29
Return
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 30
Setting the Picture (PC Mode)
➢
12
TV
PC Setup
Image Lock
√
Position
√
Information
√
Auto Adjustment
√
Preset to the PC mode by using the SOURCE button.
If you get the PC information, select the Information by pressing
the … or † button. Press the ENTER (
) button.
Result:
13
Enter
Information
Resolution
: 1024 ✻ 768
:
48.5KHz
V Frequency
:
60.2Hz
15
Return
PC Setup
Image Lock
√
Position
√
Information
√
Auto Adjustment
√
Move
TV
The options available in the PC Setup group are
displayed again.
Enter
Return
Auto Adjustment
Auto Adjusting
English - 30
Press the … or † button to select Auto Adjustment.
Press the ENTER (
) button.
Result:
H Frequency
TV
) button.
Return
14
TV
The resolution, horizontal and vertical frequency are
displayed.
Press the MENU (
Result:
Move
(continued)
The screen quality and position are automatically reset
with the Auto Adjusting displayed.
When you are satisfied with the settings, press the MENU (
button repeatedly to return to the normal viewing.
)
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 31
Using the Fine Tune
If reception is weak, you can fine tune a channel manually.
TV
1
Press the MENU (
Result:
2
) button.
The main menu is displayed.
Press the … or † button to select Channel.
Result:
The options available in the Channel group are
displayed.
3
Press the ENTER (
4
Press the … or † button to select Fine Tune.
Press the ENTER (
) button.
Result:
5
Channel
Country
√
: Austria
Auto Store
√
Manual Store
√
Edit
√
Fine Tune
√
Ch. Scan
√
Move
Enter
Return
) button.
Fine Tune
P1
0
The horizontal bar is displayed. Move the horizontal
bar’s cursor left or right by pressing the œ or √ button
to reach the required setting.
Reset
Move
Press the œ or √ button until the picture and sound are both clear
and sharp. Press the ENTER (
) button.
Return
œ √ Adjust
Store
Fine Tune
P1
6
To reset the fine tuning to 0, select Reset by pressing the … or †
button then press the ENTER (
) button.
3
Reset
Move
➢
➢
If you are unable to fine tune a channel, check that the
Colour System and Sound System settings are correct.
Return
œ √ Adjust
Store
Fine Tune
Fine tune Store will change the colour of the Channel
OSD(On Screen Display) from White to Red.
P 1 is Fine Tuned
3
Reset
Move
P1
Return
œ √ Adjust
C11
English - 31
Store
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 32
Viewing the Channel Scan Picture
TV
1
Channel
Country
: Austria
√
Manual Store
√
Edit
√
Fine Tune
√
Ch. Scan
√
Enter
Return
Result:
√
Auto Store
Move
Press the MENU (
2
) button.
The main menu is displayed.
Press the … or † button to select Channel.
Result:
The options available in the Channel group are
displayed.
3
Press the ENTER (
4
Press the … or † button to select Ch. Scan.
Press the ENTER (
) button.
) button.
Ch. Scan
Result:
P1✽
5
Return
You can view every memorized channel in order.
Press the MENU (
➢
) button to exit.
When PIP ON is activated, the PIP will appear in Large
mode and PIP channel will be scanned.
Freezing the Current Picture
You can freeze the picture when watching a television programme
simply by pressing the “STILL” button. To return to normal viewing,
press it again.
➢
➢
English - 32
In the PIP mode, the main and sub pictures are stilled at
the same time.
This function will automatically cancel after 5 minutes.
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 33
Selecting the Picture Size
You can select the picture size which best corresponds to your
viewing requirements.
1
Press the MENU (
Result:
2
TV
) button.
The main menu is displayed.
Press the … or † button to select Picture.
Result:
The options available in the Picture group are
displayed.
3
Press the ENTER (
4
Press the … or † button until the Size is selected.
Press the ENTER (
) button.
5
) button.
Move
6
Press the ENTER (
) button to confirm.
: Dynamic
: Normal
: Off
: 16 : 9
Enter
TV
Return
Size
Auto Wide
16:9
Panorama
Zoom
Press the … or † button to change the setting.
◆ Auto Wide : Expanding and pulling up the picture from 4:3
to 16:9 ratio.
◆ 16:9
: Sets the picture to 16:9 wide mode.
◆ Panorama : Use this mode for the wide aspect ratio of a
panoramic picture.
◆ Zoom
: Magnify the size of the picture vertically on
screen.
◆ 14:9
: Magnify the size of the picture more than 4:3.
◆ 4:3
: Sets the picture to 4:3 normal mode.
Picture
Mode
Custom
Colour Tone
Colour Control
Film Mode
Size
PIP
† More
14:9
4:3
Move
Enter
Return
PC to DVI Mode
TV
Size
Auto Wide
16:9
Panorama
Zoom
14:9
➢
4:3
◆ You can select these options by simply pressing the
P.SIZE button on the remote control.
Move
Enter
◆ The picture size can not be changed in the PIP mode.
◆ Depending on the input source, the P.SIZE options
may vary.
Positioning and Sizing the screen using Zoom
➢
◆ Resizing the screen using the Zoom enables the
positioning and sizing of the screen to up/down
direction using the … or † button as well as the
screen size.
◆ Move the screen up/down using the … or † button
after selecting the
by pressing the … or † button.
◆ Resize the screen vertically using the … or † button
after selecting the
by pressing the … or † button.
◆ Screen enlargement operates only in TV/Video/
S-Video/Component1,2 input modes.
◆ PC/DVI modes prevents the screen enlargement
function.
English - 33
Return
√
√
√
√
√
√
√
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 34
Selecting the Film Mode
You can automatically sense and process film signals from some
sources and adjust the picture for optimum quality.
TV
Picture
Mode
Custom
Colour Tone
Colour Control
Film Mode
Size
PIP
† More
Move
: Dynamic
: Normal
: Off
: 16 : 9
Enter
TV
√
√
√
√
√
√
√
Return
1
Press the MENU (
) button.
Result:
The main menu is displayed.
2
Press the … or † button to select Picture.
The options available in the Picture group are displayed.
Result:
3
Press the ENTER (
4
Press the … or † button to select Film Mode.
Press the ENTER (
) button.
5
Select Off or On by pressing the … or † button.
Picture
Mode
Custom
Colour Tone
Colour Control
Film Mode
Size
PIP
† More
Move
: Dynamic
: Normal
◆ On : Automatically senses and processes film signals from
some sources and adjusts the picture for optimum quality.
◆ Off : Switches off the Film Mode.
: Off Off
: 16 :On
9
6
Enter
) button.
Return
Press the ENTER (
➢
) button to confirm.
◆ Not available in the PC, Component (480p, 576p, 720p,
1080i) or DVI modes.
◆ Mode discrepancies, such as turning off Film Mode while
viewing a film source or turning on Film Mode while viewing
non-film sources, may affect the picture quality.
DNIeTM (Digital Natural Image engine)
TV
Picture
Mode
Custom
Colour Tone
Colour Control
Film Mode
Size
PIP
† More
Move
: Dynamic
: Normal
: Off
: 16 : 9
Press the MENU (
Result:
Picture
Demo
Enter
Result:
The main menu is displayed.
The options available in the Picture group are displayed.
3
Press the ENTER (
4
Press the … or † button until the DNIe is selected.
Press the ENTER (
) button.
5
Press the … or † button to change the setting.
◆ On: Switches on the DNIe mode.
◆ Off: Switches off the DNIe mode.
◆ Demo (Option): The screen before applying DNIe appears on
the right and the screen after applying DNIe
appears on the left.
6
Press the ENTER (
Return
➢
English - 34
) button.
Press the … or † button until the Picture is selected.
Return
… More
DNIe
: On On
My Colour Control
Off
Move
1
2
Enter
TV
√
√
√
√
√
√
√
This feature bring you more detailed image with 3D noise reduction, detail
enhancement, contrast enhancement and white enhancement. This feature
brings you a more detailed image with 3D noise reduction and detail, contrast
and white enhancement.
) button.
) button to confirm.
You can also set these options simply by pressing the
DNIe button.
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 35
Setting the My Colour Control (Easy Control)
This feature allows you to adjust colours according to their
preferences, by adjusting skin, sky, and grass tones using the
predefined settings (“Blue”, “Green”, “Pink”, “Standard”, and
“Custom”) without affecting other colours on the screen.
1
Press the MENU (
Result:
2
Mode
Custom
Colour Tone
Colour Control
Film Mode
Size
PIP
† More
) button.
The main menu is displayed.
Press the … or † button to select Picture.
Result:
The options available in the Picture group are
displayed.
3
Press the ENTER (
4
Press the … or † button to select My Colour Control.
Press the ENTER (
) button.
Result:
Picture
TV
Move
: Off
: 16 : 9
Enter
Return
Easy Control
Detail Control
) button.
√
√
: Blue
The options available are displayed with the Easy
Control is selected.
Press the ENTER (
Result :
: Normal
My Colour Control
TV
Move
5
√
√
√
√
√
√
√
: Dynamic
Enter
Return
) button.
The following modes are available:
◆ Blue
Emphasizing Clear Blues.
Original
Blue
◆ Green
Emphasizing Mild Greens.
◆ Pink
Emphasizing Warm Skin Colours.
◆ Standard
Standard Picture
Easy Control
Blue
Move
Green
Enter
◆ Custom
Changing the settings in the Detail Control
menu will automatically set to Custom (see next
page).
6
Select the required mode by pressing the œ or √ button.
Result :
The original picture (before adjustment) is shown on
the left side, while the selected mode is shown on the
right side.
7
Press the ENTER (
➢
◆ Depending on the input source, this feature may not
operate.
) button to confirm.
◆ This feature is operated when the “DNIe” is set to “On”
or “Demo” mode.
English - 35
Pink
√
Return
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 36
Setting the My Colour Control (Detail Control)
This settings can be adjusted to suit your personal preferences.
Picture
TV
Mode
Custom
Colour Tone
Colour Control
Film Mode
Size
PIP
† More
Move
√
√
√
√
√
√
√
: Dynamic
: Normal
: Off
: 16 : 9
Enter
Easy Control
Detail Control
Press the MENU (
Result:
2
Result:
Enter
TV
Return
Detail Control
Pink
Green
Blue
Reset
4
Press the ▲ or ▼ button to select My Colour Control.
Press the ENTER (
) button.
5
Press the ▲ or ▼ button to select Detail Control.
Press the ENTER (
) button.
7
Press the œ or √ button until you reach the required setting.
Result :
8
Original
Return
9
Adjusted
10
Pink
50
Move
Adjust
TV
Return
Detail Control
Pink
Green
Blue
Reset
Move
50
50
100
Enter
English - 36
Return
Changing the adjustment value will refresh the adjusted
screen.
Press the MENU (
) button.
The options available in the Detail Control group
are displayed again.
To return the factory defaults, select Reset by pressing
the ▲ or ▼ button.
Result:
Detail Control
The options available are displayed.
Select the required option (Pink, Green or Blue) by pressing the
▲ or ▼ button. Press the ENTER (
) button.
50
50
100
Enter
) button.
6
Result:
Move
The options available in the Picture group are
displayed.
Press the ENTER (
Result:
Move
The main menu is displayed.
3
√
√
: Blue
) button.
Press the … or † button to select Picture.
Return
My Colour Control
TV
1
The previously adjusted colours will be reset to the
factory defaults.
Press the ENTER (
) button.
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 37
Setting the Blue Screen
TV
If no signal is being received or the signal is very weak, a blue screen automatically replaces the noisy picture background. If you wish to continue viewing the
poor picture, you must set the “Blue Screen“ mode to “Off“.
1
Press the MENU (
Result:
2
) button.
The main menu is displayed.
Press the … or † button to select Setup.
Result:
The options available in the Setup group are displayed.
3
Press the ENTER (
4
Press the … or † button to select Miscellaneous.
Press the ENTER ( ) button.
Result:
Setup
Time
Language
: English
AV Setup
Digital NR
: On
Miscellaneous
PC Setup
Colour Weakness: Off
Burn Protection
Move
Enter
TV
√
Blue Screen
: Off
√
Fan
: On
√
The options available in the Miscellaneous group are
displayed.
Press the … or † button to select Blue Screen.
Press the ENTER (
) button.
6
Select Off or On by pressing the … or † button.
7
Press the ENTER (
Enter
TV
Return
Miscellaneous
Melody
: Off
Plug & Play
Blue Screen
➢
√
: Off
Plug & Play
Move
5
Return
Miscellaneous
Melody
) button.
√
√
√
√
√
√
√
√
) button to confirm.
:
Off
: Off On
Fan
◆ Blue Screen is displayed while no signal from the external
device in the External Mode, regardless of the Blue Screen
Setting.
Move
Enter
Return
Setting the Melody Sound
TV
You can hear clear melody sound when the television is powered on or off.
1
Press the MENU (
) button.
The main menu is displayed.
Result:
2
Press the … or † button to select Setup.
The options available in the Setup group are displayed.
Result:
3
Press the ENTER (
4
) button.
Miscellaneous
Melody
: Off
√
Fan
: On
√
Move
Enter
TV
Result:
Press the … or † button to select Melody.
Press the ENTER (
) button.
6
Select Off or On by pressing the … or † button.
7
Press the ENTER (
Return
Miscellaneous
Press the … or † button to select Miscellaneous.
Press the ENTER (
) button.
5
√
Blue Screen
Melody
The options available in the Miscellaneous group are
displayed.
√
: Off
Plug & Play
Plug & Play
: Off Off
On
Blue Screen
: Off
Fan
: On
Move
Enter
) button to confirm.
English - 37
Return
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 38
Using the Colour Weakness Enhancement Feature
This Feature adjusts the Red, Green, or Blue colour to enhance
the picture according to the user's particular colour weakness.
TV
Setup
√
√
√
√
√
√
√
√
Time
Language
: English
AV Setup
Digital NR
: On
Miscellaneous
PC Setup
Colour Weakness: Off
Burn Protection
Move
TV
Enter
Return
Colour Weakness
TV
Enter
Return
Colour Weakness
√
0
0
0
Colour Weakness : On
Red
Green
Blue
Move
Enter
Return
Colour Weakness
Red
Move
0
Adjust
English - 38
Press the MENU (
) button.
The main menu is displayed.
Result:
2
Press the … or † button to select Setup.
The options available in the Setup group are
Result:
displayed.
3
Press the ENTER (
4
Press the … or † button to select Colour Weakness.
Press the ENTER (
) button.
The options available in the Colour Weakness
Result:
group are displayed.
5
Press the ENTER ( ) button again.
Press the … or † button to select On, then press the
ENTER (
) button.
6
Press the … or † button to select the colour you wish to adjust,
then press the ENTER ( ) button.
7
Press the œ or √ button to adjust to your preference.
8
Press the MENU (
√
0
0
0
Colour Weakness : Off
Red
Green
Blue
Move
1
Return
) button.
) or ENTER (
) button to confirm.
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 39
Viewing the Picture In Picture (PIP)
You can display a sub picture within the main picture of TV program or external
A/V devices. In this way you can watch TV program or monitor the video input
from any connected devices while watching TV or other video input.
1
TV
Press the MENU (
) button.
Result:
The main menu is displayed.
2
Press the … or † button to select Picture.
The options available in the Picture group are displayed.
Result:
3
Press the ENTER (
4
Press the … or † button to select PIP.
Press the ENTER (
) button.
Picture
Mode
Custom
Colour Tone
Colour Control
Film Mode
Size
PIP
† More
Move
Result:
5
Press the ENTER (
) button again.
To activate, set the PIP to on by pressing the … or † button.
Press the ENTER (
) button.
6
Press the … or † button to select Source.
Press the ENTER (
) button.
Result:
The sources are displayed in the following order:
TV - Ext.1 - Ext.2 - Ext.3 - AV1 - AV2 - AV3 - S-Video1 S-Video2 - Component1 - Component2 - PC - DVI
7
8
9
Move
PIP
Main TV
TV
Ext.1
Ext.2
Ext.3
AV1
AV2
AV3
S-Video1
S-Video2
Component1
Component2
PC
DVI
O
O
O
O
O
O
O
O
O
O
O
O
O
Ext.1 Ext.2 Ext.3 AV1 AV2 AV3 S-Video1 S-Video2 Component1 Component2 PC DVI
O
O
O
O
O
O
O
O
O
O
O
O
X
O
O
O
O
O
O
O
O
O
O
O
O
X
O
O
O
O
O
O
O
O
O
O
O
O
X
O
O
O
O
O
O
O
O
O
O
O
O
X
O
O
O
O
O
O
O
O
O
O
O
O
X
O
O
O
O
O
O
O
O
O
O
O
O
X
O
O
O
O
O
O
O
O
O
O
O
O
X
O
O
O
O
O
O
O
O
O
O
O
O
X
O
O
O
O
O
O
O
O
O
O
O
O
X
X
X
X
O
O
O
O
O
O
O
O
X
X
X
X
O
O
O
O
O
O
O
O
X
X
X
X
O
O
O
O
O
O
O
O
X
X
X
X
Return
PIP
: On
: TV
TV
Ext.1
:
Ext.2
Ext.3
:
: P08 AV1
AV2
†
Move
Enter
Return
PIP
TV
PIP
Source
Swap
Size
Position
Prog.
◆ The Double 1 or Double 2 mode can not be
selected in PC or DVI mode.
X - This PIP combination is not available.
O - This PIP combination is available.
Enter
PIP
Source
Swap
Size
Position
Prog.
The sizes are displayed in the following order:
Table of PIP Settings
:
:
: P 11
TV
Press the … or † button to select Size.
Press the ENTER (
) button.
Select a size of the sub picture by pressing the … or † button.
Press the ENTER (
) button.
: On Off
: TV On
Source
Swap
Size
Position
Prog.
(Large) - (Small) - (Double1) - (Double2)
10
Return
PIP
PIP
◆ The PC can not be selected in DVI mode.
◆ The DVI can not be selected in PC mode.
Press the … or † button to select Swap.
Press the ENTER (
) button.
Result:
The main picture and sub picture are interchanged.
➢
: Off
: 16 : 9
Enter
TV
Select a source of the sub picture by pressing the … or † button.
Press the ENTER (
) button.
Result:
: Normal
√
√
√
√
√
√
√
) button.
The options available in the PIP group are displayed.
➢
: Dynamic
Move
: On
: TV
√
√
√
:
:
: P11
√
√
Enter
√
Return
PIP
TV
PIP
Source
Swap
Size
Position
Prog.
Move
: On
: TV
:
:
: P08
Enter
English - 39
Return
BN68-00718K-00Eng_1014
10/18/04
5:07 PM
Page 40
Viewing the Picture In Picture (PIP) (continued)
11
PIP
TV
PIP
Source
Swap
Size
Result:
:
:
: P08
Position
Prog.
Move
The positions available are displayed.
-
Enter
-
-
12
Select a position by pressing the … or † button.
Press the ENTER (
) button.
13
Press the … or † button to select Prog..
Press the ENTER (
) button.
14
Select the channel that you want to view through sub picture by
pressing the … or † button. Press the ENTER (
) button.
Return
PIP
TV
PIP
Source
: On
: TV
Swap
Size
Position
Prog.
:
:
: P08
Move
Press the … or † button to select Position.
Press the ENTER (
) button.
: On
: TV
Enter
➢
P1
Return
If the sub picture is no signal and the main picture is
output from a Component, PC or DVI signal, the sub
picture will be blue. If the main picture is output from a
Video signal, the sub picture will be black.
Easy functions of remote control.
Buttons
Feature
PIP ON
Used to activate or deactivate the PIP function directly.
SWAP
Used to interchange the main picture and the sub
picture.
➢
English - 40
When the main picture is in the Video mode and
the sub picture is in the TV mode, you might not
hear the sound of main picture when pressing
the SWAP (
) button after changing the sub
picture channel. At this time, reselect the channel
of main picture.
POSITION
Used to move the sub picture counterclockwise.
SOURCE
Used to assign a source of sub picture (TV, Ext.1,
Ext.2, Ext.3, AV1, AV2, AV3, S-Video1, S-Video2,
Component1, Component2, PC, or DVI).
SIZE
Used to select a size of sub picture (Large, Small,
Double1, or Double2).
SCAN
Used to scan every memorized channel in order.
To stop scanning, press it again.
P
Used to select the channel of sub picture.
/
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 41
Using the Digital NR (Noise Reduction) Feature
If the signal received by your television is weak, you can activate
this feature to help reduce any static and ghosting that may appear
on the screen.
1
Press the MENU (
) button.
The main menu is displayed.
Result:
2
Press the … or † button until the Setup is selected.
The options available in the Setup group are displayed.
Result:
3
Press the ENTER (
4
Press the … or † button until the Digital NR is selected.
Press the ENTER (
) button.
5
Select Off or On by pressing the … or † button.
Press the ENTER (
) button to confirm.
TV
Setup
Time
Language
: English
AV Setup
Digital NR
: On
Miscellaneous
PC Setup
Colour Weakness: Off
Burn Protection
Move
Enter
√
√
√
√
√
√
√
√
Return
) button.
TV
Setup
Time
Language
: English
AV Setup
Digital NR
: On Off
Miscellaneous
On
PC Setup
Colour Weakness: Off
Burn Protection
Move
Enter
Return
Selecting the Fan
Operates or stops the TV’s internal Fan.
What is the Fan: Fans inside the TV are used to reduce the temperature of
the tops and the front of the TV. To reduce the noise of the fan, you may
stop the fan by setting the Fan to “Off”. The temperature of the top and
the front of the TV may increase when you watch the TV for a long
period of time while the fan is stopped, but the TV will operate normally.
1
2
TV
Press the MENU (
) button.
The main menu is displayed.
Result:
Press the … or † button to select Setup.
The options available in the Setup group are displayed.
Result:
Setup
Time
Language
: English
AV Setup
Digital NR
: On
Miscellaneous
PC Setup
Colour Weakness: Off
Burn Protection
Move
Enter
TV
Miscellaneous
Melody
3
Press the ENTER (
) button.
4
Press the … or † button to select Miscellaneous.
The options available in the Miscellaneous group are
Result:
displayed.
5
Press the ENTER (
6
Press the … or † button to select Fan.
Press the ENTER (
) button.
7
Select Off or On by pressing the … or † button.
8
Press the ENTER (
) button.
Return
: Off
Plug & Play
Blue Screen
: Off
Fan
: On Off
On
Move
Enter
) button to confirm.
English - 41
Return
√
√
√
√
√
√
√
√
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 42
Protecting the Screen Burning
You can prevent the residual image of the PDP.
TV
Setup
Time
Language
: English
AV Setup
Digital NR
: On
Miscellaneous
PC Setup
Colour Weakness: Off
Burn Protection
Move
Enter
TV
√
√
√
√
√
√
√
√
Return
1
Press the MENU (
) button.
The main menu is displayed.
Result:
2
Press the … or † button to select Setup.
The options available in the Setup group are
Result:
displayed.
3
Press the ENTER (
4
Press the … or † button to select Burn Protection.
5
Press the ENTER (
) button.
The Burn Protection menu is displayed with the
Result:
Pixel Shift selected.
6
Press the ENTER (
) button.
Burn Protection
√
Pixel Shift
All White
: Off
√
Signal Pattern
: Off
√
Result:
Move
Enter
TV
Return
7
Press the ENTER (
) button. Set to On by pressing the … or †
button for making the screen move per regular hour and
preventing the residual image, then press the ENTER (
)
button.
8
Select the option (Horizontal Dot, Vertical Line, or Time) to
be adjusted by pressing the … or † button.
Press the ENTER (
) button.
Pixel Shift
Pixel Shift
:
Horizontal Dot
: Off On
Off
Vertical Line
: 4
Time
: 4 Min
Move
Enter
TV
➢
Return
Burn Protection
Pixel Shift
All White
Signal Pattern
Move
Horizontal Dot
2
Vertical Line
4
Time
4MIN
9
Press the … or † button to reach the required setting.
Press the ENTER (
) button.
10
When you are satisfied with the settings, press the MENU (
button. Press the ENTER (
) button.
11
Press the … or † button to select All White.
Press the ENTER (
) button. Set to On by pressing the … or †
button for removing the residual image after making the screen
white. Press the ENTER (
) button.
12
Press the … or † button to select Signal Pattern.
Press the ENTER (
) button. Set to On by pressing the … or †
button for removing the residual image.
Press the ENTER (
) button.
Return
Burn Protection
Pixel Shift
All White
: Off
Signal Pattern
: Off Off
On
Move
Optimum condition for pixel shift;
: Off Off
: Off On
Enter
TV
) button again.
The Pixel Shift menu is displayed with the
Pixel Shift selected.
Enter
Return
➢
English - 42
The Signal Pattern and All White feature are
effective after working for a long time.
)
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 43
Changing the Sound Standard
You can select the type of special sound effect to be used when
watching a given broadcast.
TV
Sound
Mode
1
Press the MENU (
Result:
2
: Standard
The main menu is displayed.
Auto Volume
: Off
√
SRS TSXT
: Off
√
Internal Mute
: Off
√
Press the … or † button to select Sound.
Result:
The options available in the Sound group are displayed.
Move
3
Press the ENTER (
Result:
Enter
Return
) button.
The Mode is selected.
4
Press the ENTER (
5
Select the option by pressing the … or † button. The sound
effects are displayed in the following order.
) button again.
TV
Sound
Mode
: Standard
Standard
Equalizer
Music
Auto Volume
: Off
SRS TSXT
: Off
Internal Mute
: Off
Custom
Movie
Speech
Standard - Music - Movie - Speech - Custom.
6
Press the ENTER (
➢
) button to confirm.
√
√
Equalizer
) button.
Move
Enter
You can also set these options simply by pressing the
S.MODE (
: Sound Mode) button.
English - 43
Return
BN68-00718K-00Eng_1014
10/18/04
5:07 PM
Page 44
Adjusting the Sound Settings
The sound settings can be adjusted to suit your personal preferences.
TV
Sound
Mode
√
: Custom
Auto Volume
: Off
√
SRS TSXT
: Off
√
Internal Mute
: Off
√
Move
1
Press the MENU (
) button.
The main menu is displayed.
Result:
2
Press the … or † button to select Sound.
The options available in the Sound group are displayed.
Result:
3
Press the ENTER (
4
Press the … or † button to select Equalizer.
Press the ENTER (
) button.
The Equalizer menu is displayed with the current
Result:
option.
5
Select the option (volume, balance, or equalizer) to be adjusted by
pressing the œ or √ button. Press the … or † button to reach the
required setting.
6
When you are satisfied with the settings, press the MENU (
button to store them.
√
Equalizer
Enter
Equalizer
TV
0
) button.
Return
R
+
+
0
0
_
_
L
100Hz 300Hz 1kHz 3kHz 10kHz
√ Move
Adjust
Return
➢
)
If you make any changes to the equalizer settings, the
sound standard is automatically switched to the Custom.
Adjusting the Volume Automatically
Sound
TV
Mode
: Custom
√
√
Equalizer
Auto Volume
: Off
√
SRS TSXT
: Off
√
Internal Mute
: Off
√
Move
Enter
TV
Each broadcasting station has its own signal conditions, and so it
is not easy for you to adjust the volume every time the channel is
changed. This feature lets you automatically adjust the volume of
the desired channel by lowering the sound output when the
modulation signal is high or by raising the sound output when the
modulation signal is low.
1
Press the MENU (
) button.
The main menu is displayed.
Result:
2
Press the … or † button to select Sound.
The options available in the Sound group are displayed.
Result:
3
Press the ENTER (
4
Press the … or † button to select Auto Volume.
Press the ENTER (
) button.
5
Select the option (Off or On) by pressing the … or † button.
6
Press the ENTER (
Return
Sound
Mode
: Custom
Equalizer
Auto Volume
SRS TSXT
Internal Mute
Move
: Off Off
: Off On
: Off
Enter
English - 44
Return
) button.
) button to confirm.
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 45
Setting the TruSurround XT
TruSurround XT is a patented SRS technology that solves the
problem of playing 5.1 multichannel content over two speakers.
TruSurround delivers a compelling, virtual surround sound
experience through any two-speaker playback system, including
internal television speakers. It is fully compatible with all
multichannel formats.
1
Press the MENU (
Result:
2
TV
) button.
√
SRS TSXT
: Off
√
Internal Mute
: Off
√
The main menu is displayed.
Move
Enter
TV
Sound
Press the … or † button until the SRS TSXT is selected.
Press the ENTER (
) button.
Equalizer
Press the … or † button to change the setting.
(Off, 3D Mono, or Stereo.)
Press the ENTER (
➢
Return
The options available in the Sound group are displayed.
4
➢
√
: Off
Press the ENTER (
6
√
Auto Volume
3
5
: Standard
Equalizer
Press the … or † button until the Sound is selected.
Result:
Sound
Mode
) button.
Mode
: Standard
Auto Volume
: Off
SRS TSXT
: Off Off
Internal Mute
: Off
3D Mono
Stereo
) button to confirm.
Move
Enter
Return
TruSurround XT, SRS and
Symbol are trademarks of
SRS Labs, Inc. TruSurround XT
technology is incorporated under
license from SRS Labs, Inc.
You can also set these options simply by pressing the
SRS TSXT (
)button.
Selecting the Internal Mute
TV
If you want to hear the sound through separate speakers,
cancel the internal amplifier.
1
Press the MENU (
Result:
2
: Standard
) button.
Auto Volume
: Off
√
SRS TSXT
: Off
√
Internal Mute
: Off
√
The main menu is displayed.
The options available in the Sound group are displayed.
3
Press the ENTER (
4
Press the … or † button to select Internal Mute.
Press the ENTER (
) button.
) button.
Move
Enter
TV
Return
Sound
Mode
: Standard
Equalizer
Auto Volume
: Off
SRS TSXT
: Off
Internal Mute
: Off Off
On
5
Select Off or On by pressing the … or † button.
6
Press the ENTER (
) button to confirm.
√
√
Equalizer
Press the … or † button to select Sound.
Result:
Sound
Mode
Move
Enter
English - 45
Return
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 46
Selecting the Sound Mode (depending on the model)
The “DUAL I-II” button displays/controls the processing and output
of the audio signal. When power is switched on, the mode is
automatically preset to either “DUAL-I ” or “Stereo”, depending on
the current transmission.
NICAM
Stereo
Type of broadcast
On-screen indication
Regular broadcast
(Standard audio)
Mono (Normal use)
Regular +
NICAM Mono
NICAM Mono ↔ Mono
NICAM Stereo
A2
Stereo
NICAM DUAL-I/II
NICAM DUAL-I →
NICAM DUAL-II →
Mono
Regular broadcast
(Standard audio)
Mono
Bilingual or DUAL-I/II
DUAL-I ↔ DUAL-II
Stereo
➢
NICAM Stereo ↔ Mono
(Forced mono)
Stereo ↔ Mono
(Forced mono)
◆ If the receiving conditions deteriorate, listening will be
easier if the mode is set to the Mono.
◆ If the stereo signal is weak and an automatic switching
occurs, then switch to the Mono.
◆ When receiving a mono sound in the AV mode, connect
to the “AUDIO-L” input connector on the side of the
television. If the mono sound comes out only from left
speaker, press the DUAL I-II button.
English - 46
BN68-00718K-00Eng_1014
10/18/04
5:07 PM
Page 47
Setting the Sleep Timer
You can select a time period of between 30 and 180 minutes after
which the television automatically switches to Standby mode.
1
Press the MENU (
Result:
2
TV
) button.
The main menu is displayed.
Press the … or † button to select Setup.
Result:
Setup
Time
Language
: English
AV Setup
Digital NR
: On
Miscellaneous
PC Setup
Colour Weakness: Off
Burn Protection
The options available in the Setup group are
displayed.
Move
Enter
√
√
√
√
√
√
√
√
Return
3
Press the ENTER (
4
Press the … or † button to select Time.
Press the ENTER (
) button.
Clock
07 : 05
√
Sleep Timer
Off
√
Result:
On Timer
Off
√
Off Timer
Off
√
) button.
TV
5
The options available in the Time group are displayed.
Time
Press the … or † button to select Sleep Timer.
Press the ENTER (
) button.
Result:
The Sleep Timer menu is displayed with the Min is
selected.
6
Select the preset time intervals (-- (Off), 30, 60, 90, 120, 150, or
180) by pressing the … or † button.
7
Press the œ or √ button to move to the Activation.
8
When you are satisfied with the settings, select Activation to
Yes or No by pressing the … or † button.
9
Press the ENTER (
➢
Move
TV
) button to confirm your selection.
◆ You can also set these options simply by pressing the
SLEEP button.
Enter
Return
Sleep Timer
Adjust
Min
Activation
--
No
√ Move
TV
Return
Sleep Timer
◆ If the sleep timer is not yet set, Off is displayed.
If the sleep timer is already set, the remaining time
before which the television switches to Standby mode
is displayed.
Adjust
Min
Activation
30
Yes
œ √ Move
Off
English - 47
Return
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 48
Setting and Displaying the Current Time
TV
Setup
Time
Language
: English
AV Setup
Digital NR
: On
Miscellaneous
PC Setup
Colour Weakness: Off
Burn Protection
Move
Enter
TV
√
√
√
√
√
√
√
√
You can set the television’s clock so that the current time is displayed
by pressing the “INFO (
)” button. You must also set the time if
you wish to use the automatic on or off timers.
➢
1
Press the MENU (
) button.
The main menu is displayed.
Result:
2
Press the … or † button to select Setup.
The options available in the Setup group are
Result:
displayed.
3
Press the ENTER (
4
Press the … or † button to select Time.
Press the ENTER (
) button.
The options available in the Time group are displayed
Result:
with Clock is selected.
5
Press the ENTER (
6
Press the "!button to move to the Hour or Min.
Set the Hour or Min by pressing the … or † button.
7
When you have finished, press the MENU (
8
Press the INFO (
Return
Time
Clock
07 : 05
√
Sleep Timer
Off
√
On Timer
Off
√
Off Timer
Off
√
Move
Enter
TV
Return
Clock
Adjust
Hour
Min
01
00
√ Move
English - 48
Return
When pressing the “I / ” button (On/Off) on the front of
the television, the clock setting will be reset.
) button.
) button.
) button to exit.
) button to display the current time.
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 49
Switching the Television On and Off Automatically
You can set the television’s clock and set the On or Off timers so that
the television will:
◆ Switch on automatically and tune to the channel of your
choice at the time you select
TV
◆ Switch off automatically at the time you select
➢
Setup
Time
Language
: English
AV Setup
Digital NR
: On
Miscellaneous
PC Setup
Colour Weakness: Off
Burn Protection
The first step is to set the television’s clock (refer to
“Setting and Displaying the Current Time” on the
previous page).
Move
1
Press the MENU (
) button.
The main menu is displayed.
Result:
2
Press the ENTER (
4
Press the … or † button to select Time.
Press the ENTER (
) button.
The options available in the Time group are displayed.
Result:
5
) button.
Press the … or † button to select On Timer.
Press the ENTER (
) button.
Result:
The options available in the On Timer group are
displayed.
6
Select the Hour, Min, Prog., or Volume by pressing the √ button.
Set these by pressing the … or † button.
7
Press the œ or √ button to move to the Activation.
8
When you are satisfied with the settings, select Activation to
Yes or No by pressing the … or † button.
9
Return
TV
Press the … or † button to select Setup.
The options available in the Setup group are displayed.
Result:
3
Enter
Time
Clock
07 : 05
√
Sleep Timer
Off
√
On Timer
Off
√
Off Timer
Off
√
Move
Enter
TV
Return
On Timer
Adjust
Hour
Min
Prog.
12
01
1
Volume
Activation
10
No
√ Move
TV
Return
Off Timer
Press the MENU (
) button.
Result:
The options available in the Time group are displayed
again.
Hour
Min
12
00
Activation
10
Press the … or † button to select Off Timer.
Press the ENTER (
) button.
The Off Timer menu is displayed.
Result:
11
Select the Hour, Min, or Activation by pressing the √ button.
Set these by pressing the … or † button.
12
Press the ENTER (
➢
➢
√
√
√
√
√
√
√
√
No
Adjust
√ Move
) button to confirm.
Auto Power Off
Auto Power OFF will automatically turn the TV off if you do not
operate any controls within 3 hours after the TV is turned on by
the timer. This function is available in the timer “On” mode
only and will prevent a leakage accldent or overheating caused
by your TV being left on too long.
If no signal is received for 15 minutes, the TV will be
automatically turned off.
English - 49
Return
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 50
Viewing an External Signal Source
TV
Input
Source List
√
: TV
Use the remote control to switch between viewing signal from
connected equipment, such as VCR, DVD, Set-Top-boxs, and the
TV source (broadcast or cable)
√
Edit Name
1
Press the MENU (
Result:
2
Move
Enter
TV
Result:
Source List
Move
-------------------
Enter
TV
Press the … or † button to select Input .
Return
TV
Ext.1
Ext.2
Ext.3
AV1
AV2
AV3
▼ More
Press the ENTER (
4
Press the … or † button to select Source List.
Press the ENTER (
) button.
5
➢
√
: TV
√
Edit Name
Move
Enter
TV
Move
:
:
:
:
:
:
:
- ------ VCR
DVD
Cable STB
HD STB
Satellite STB
Enter
7
Press the … or † button to select Edit Name.
Press the ENTER (
) button.
Result:
) button and select Input.
The options available in the Edit Name group are
displayed.
8
Press the … or † button to select external device :
Ext.1 - Ext.2 - Ext.3 - AV1 - AV2 - AV3 - S-Video1 S-Video2 - Component1 - Component2 - PC - DVI
9
Press the ENTER (
) button.
The Edit Name available are listed.
Result:
10
Select the name by pressing the … or † button.
Press the ENTER (
) button.
11
Set other signal sources (VCR, DVD, Cable STB, HD STB,
Satellite STB, AV Receiver, DVD Receiver, Game,
Camcorder, DVD Combo, DHR, or PC) using the same method as
listed above.
➢
➢
English - 50
When you connect equipment to the TV, you can choose
between the following sets of jacks : Ext.1, Ext.2, Ext.3,
AV1, AV2, AV3, S-Video1, S-Video2, Component1,
Component2, PC, or DVI on the TV’s rear panel.
Press the MENU (
†
Return
The options available in the Source List group are
displayed.
6
Return
Edit Name
Ext.1
Ext.2
Ext.3
AV1
AV2
AV3
S-Video1
▼ More
) button.
Press the … or † button to select signal source, then press the
ENTER (
) button.
Input
Source List
The options available in the Input group are
displayed.
3
Result:
Return
) button.
The main menu is displayed.
You can also set these options simply by pressing the
SOURCE (
) button. If you change the external source
while viewing, pictures might take a short period of time to
be switched.
DHR: DVD HDD Recorder.
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 51
Redirecting an Input to the External Output
Your television enables you to choose which audio/video signals
are output to the external connector.
1
Press the MENU (
Result:
2
) button.
The main menu is displayed.
The options available in the Setup group are
displayed.
3
Press the ENTER (
4
Press the … or † button to select AV Setup.
Press the ENTER (
) button.
Result:
6
) button.
Move
Enter
TV
The AV Setup menu is displayed.
Press the … or † button to select required input (Ext.2 or Ext.3).
Select the source to be directed to the output by pressing the
… or † button.
Press the ENTER (
Setup
Time
Language
: English
AV Setup
Digital NR
: On
Miscellaneous
PC Setup
Colour Weakness: Off
Burn Protection
Press the … or † button to select Setup.
Result:
5
TV
√
√
√
√
√
√
√
√
Return
AV Setup
Ext.1
: TV
√
Ext.2
: TV
√
Ext.3
: TV
√
Move
Enter
Return
) button to confirm the change.
TV
AV Setup
Ext.1
: TV
Ext.2
: TV
Ext.3
: TV
TV
Ext.1
Ext.2
Ext.3
AV1
AV2
†
Move
Enter
English - 51
Return
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 52
Teletext Feature
Most television channels provide written information services via
teletext. Information provided includes:
◆
◆
◆
◆
Television programme times
News bulletins and weather forecasts
Sports results
Travel information
This information is divided into numbered pages (see diagram).
Part
Contents
A
B
C
D
E
F
➢
Selected page number.
Broadcasting channel identity.
Current page number or search indications.
Date and time.
Text.
Status information.
FASTEXT information.
Teletext information is often divided between several
pages displayed in sequence, which can be accessed by:
◆ Entering the page number
◆ Selecting a title in a list
◆ Selecting a coloured heading (FASTEXT system)
Displaying the Teletext Information
You can display Teletext information at any time on your television.
Teletext information to be displayed correctly,
☛ For
channel reception must be stable; otherwise:
◆ Information may be missing
◆ Some pages may not be displayed
1
Select the channel providing the Teletext service by pressing the
P
or
button.
2
Press the TTX/MIX (
Result:
English - 52
) button to activate the teletext mode.
The contents page is displayed. It can be redisplayed
at any time by pressing the
(index) button.
3
Press the TTX/MIX (
) button again.
The screen will be split into two. This Double Teletext
Result:
feature lets you view the actual broadcast and teletext
information separately on the screen.
4
If you wish to display the actual broadcast and teletext information
on a single screen, press the TTX/MIX (
) button again.
5
To exit from the teletext display, press the EXIT/TV (
) button.
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 53
Selecting Display Options
When you have displayed a Teletext page, you can select various
options to suit your requirements.
To display...
Press the...
◆ Hidden text
(answers to quiz games, for example)
(reveal)
◆ The normal screen
(reveal) again
◆ A secondary page by entering its number
(sub-page)
◆ The broadcast when searching for a page
(cancel)
◆ The next page
(page up)
◆ The previous page
(page down)
◆ Double-size letters in the:
• Upper half of the screen
• Lower half of the screen
(size)
• Once
• Twice
◆ The normal screen
• Three times
TV
.
English - 53
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 54
Selecting a Teletext Page
You can enter the page number directly by pressing the numeric
buttons on the remote control.
1
Enter the three-digit page number given in the content by
pressing the corresponding numeric buttons.
Result:
The current page counter is incremented and the
page is then displayed. If the selected page is linked
with several secondary pages, the secondary pages
are displayed in sequence. To freeze the display on a
given page, press the
(hold). Press it again to
resume.
2
If the FASTEXT system is used by the broadcasting company,
the different topics covered on a Teletext page are colour-coded
and can be selected by pressing the coloured buttons on the
remote control.
Press the coloured button corresponding to the topic that you wish
to select; the available topics are given on the status line.
Result:
The page is displayed with other coloured information
that can be selected in the same way.
3
To display the previous or next page, press the corresponding
coloured button.
4
To display the subpage, see the following steps.
◆ Press the
(sub-page) button.
Result:
The available subpages appear.
◆ Select the required sub-page. Sub-pages can be scrolled by
pressing the
or
button.
5
English - 54
When you have finished, press the EXIT/TV (
return to your normal broadcast.
) button to
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 55
Connecting to the External Devices
“MONITOR OUT” are used for the equipment with an RGB output, such as
video game devices or video disc players.
Rear of the TV
(Input/Output)
①
or
VCR
②
DVD
Decoder /
Video Game Device
Video Disc Player
Side of the TV
Satellite Receiver
③
① This end can be fitted with:
◆ A SCART connector
◆ Three RCA connectors (VIDEO + AUDIO-L/R)
② If you have a second VCR and wish to copy cassettes tape, connect the source VCR to
“Ext.1(Ext.2, Ext.3, AV 1, AV 2 or AV 3)” and the target VCR to “MONITOR OUT” so that you can redirect
the signal from “Ext.1(Ext.2, Ext.3, AV 1, AV 2 or AV 3)” to “MONITOR OUT”.
③ When you wish to record a programme, connect the receiver to “Ext.1(Ext.2, Ext.3, AV 1, AV 2 or AV 3)”
and the VCR to “MONITOR OUT” so that you can redirect the signal from “Ext.1(Ext.2, Ext.3, AV 1, AV 2
or AV 3)” to “MONITOR OUT”.
Input/Output Specification
Input
Connector
Output
Video
Audio (L/R)
S-Video
RGB
Video + Audio (L/R)
Ext.1
✔
✔
✔
✔
Only TV output is available.
Ext.2
✔
✔
✔
Ext.3
✔
✔
Output you can choose.
✔
Output you can choose.
English - 55
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 56
Connecting to the S-Video Input
The S-VIDEO1 and RCA (AUDIO-L/R) connectors are used for equipment with an S-Video output,
such as a camcorder or VCR.
Rear of the TV
①
and
Camcorder
Side of the TV
①
VCR
and
① To play picture and sound, both the S-VIDEO and RCA connectors must be used.
☛
English - 56
Whenever you connect an audio or video system to your television,
ensure that all elements are switched off. Refer to the documentation
supplied with your equipment for detailed connection instructions
and associated safety precautions.
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 57
Connecting to the DVI Input
The “DVI” (video) and “L-AUDIO-R” connectors are used for equipment with a DVI output.
Rear of the TV
Personal Computer
and
Connecting to the PC Input
The “RGB” (video) and “AUDIO” connectors are used for interfacing with your PC.
Rear of the TV
Personal Computer
and
English - 57
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 58
Connecting to the Component Input
Rear of the TV
① The “COMPONENT 1” connectors are
①
DVD
②
DTV receiver
used for equipment with a DVD output.
(480i,p/576i,p/720p/1080i)
② The “COMPONENT 2” connectors are
used for DTV receiver. (480i,p/576i,p/
720p/1080i)
English - 58
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 59
Connecting and Using the Home Theater System
Use the Monitor Out ports of the PDP for Home Theater System Connections.
Rear of the TV
Connecting the Home Theater System
① Connect the monitoring audio out L, and
R jacks of the MONITOR OUT on the
rear-side connection panel of the PDP
TV to the AUDIO IN jacks of the DVD
Home Theater System (or AV Receiver)
using the audio cable.
② Press the SOURCE button to select the
desired external device connected to the
PDP TV.
③ If you want to hear the sound through
separate speakers, cancel the internal
amplifier.
②
①
DVD Home Theater
☛
AV Receiver Amplifier
◆ Refer to corresponding user’s manual from the manufacturer for wiring the
speakers to the DVD Home Theater System (or AV Receiver).
◆ Disable the PDP TV internal speaker to enjoy the rich sound through the
speakers of your Home Theater System.
◆ In this case, enjoy the sound from the Home Theater System while the PDP TV
does not produce the audio.
To Display the DVD Home Theater
! Turn the PDP on and press the SOURCE button to select the Ext.1 (Ext.2 or Ext.3) or
Component(1, 2).
@ Be sure to connect the video cable properly if desired external input (Ext.1 (Ext.2 or Ext.3) or
Component(1, 2)) cannot be selected.
# Play the DVD after activating the DVD Home Theater System.
$ Use the volume control of the Home Theater System while watching the PDP using the DVD
Home Theater, where the PDP TV does not produce the audio.
English - 59
BN68-00718T-00Eng_1007
10/14/04
10:15 AM
Page 60
How to Install Speakers
➢
This speaker installation guide is for the 5040 Model.
How to Assemble the Speakers(Standing)
Parts
① Remove the screws indicated on the rear of the PDP
(6 screws on the left and right sides).
The actual product may differ
slightly from the illustration.
Speakers
② Set the Speaker Guide Bracket into the square grooves
located on either side of the PDP’s bottom rear then push
the Speaker Guide Bracket towards the center (as the arrow
illustrates). Secure the Speaker Guide Bracket with provided
screws @. (Always use the proper screws, as indicated.)
2 EA
Middle Cabinet
(Wall Mount Only)
1 EA
screw@
Speaker Dust Cover
③ Secure the Speaker Dust Cover by setting it into the
grooves located on the front side of the speakers.
1 EA
Speaker Cable
④ Connect the speakers to the PDP using the speaker cable.
The connection terminals are on the rear side of both the
PDP and the speakers.
(Match the colour coded terminals and cables.)
Screws
BLACK
Screw①
: 2EA
Screw➁
: 6EA
RED
BLACK RED
WARNING
1. When moving the PDP with the speakers attached, be sure to hold on to the PDP to prevent damage.
(Damage may occur to the speaker connecting brackets or the speakers.)
2. Speakers of 8Ω Impedance, 15W Nom. Power, 30W Max. Power is recommended.
English - 60
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
How to Install Speakers
Page 61
(continued)
How to Assemble the Speakers(Wall Mount)
Parts
① Remove the screws indicated on the rear of the PDP (6
screws on the left and right sides, 2 screws on the center).
The actual product may differ
slightly from the illustration.
Speakers
② Set the Speaker Guide Bracket into the square grooves located
on either side of the PDP’s bottom rear then push the Speaker
Guide Bracket towards the center (as the arrow illustrates).
Secure the Speaker Guide Bracket with provided screws @.
Secure the Middle Cabinet to the center of the PDP with a screw
!. (Always use the proper screws, as indicated.)
2 EA
Middle Cabinet
(Wall Mount Only)
1 EA
Screw!
Screw@
Speaker Dust Cover
③ Secure the Speaker Dust Cover by setting it into the
grooves located on the front side of the speakers.
1 EA
Speaker Cable
④ Connect the speakers to the PDP using the speaker cable.
The connection terminals are on the rear side of both the
PDP and the speakers.
(Match the colour coded terminals and cables.)
Screws
RED
BLACK
Screw①
: 2EA
Screw➁
: 6EA
BLACK RED
WARNING
1. When moving the PDP with the speakers attached, be sure to hold on to the PDP to prevent damage.
(Damage may occur to the speaker connecting brackets or the speakers.)
2. Speakers of 8Ω Impedance, 15W Nom. Power, 30W Max. Power is recommended.
English - 61
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 62
Setting up Your PC Software (Windows only)
The Windows display-settings for a typical computer are shown below. But the actual screens on your
PC will probably be different, depending upon your particular version of Windows and your particular
video card. But even if your actual screens look different, the same, basic set-up information will apply
in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer.)
1 Right click the mouse on the Windows Desktop,
then click on Properties. The Display Dialog-Box
will be displayed.
2 Click on Settings, then set the Display Mode
with reference to the Display Modes Table. You
do not need to change the Colours settings.
3 Click on Advanced. A new settings dialog box
will be displayed.
2
3
4 Click on the Monitor tab, then set the Screen
Refresh Rate with reference to the Display
Modes Table. Set the Vertical Frequency and
Horizontal Frequency individually if you can do
so instead of setting the Screen Refresh Rate.
5 Press the OK button, close the window, then
press the OK button on the Display Registration
Information window. Automatic re-booting may
commence at this moment.
6 Shutdown the PC, and connect it to your TV.
(See page 57)
4
5
English - 62
➢
◆ The actual screens on your PC may look
different, depending on your particular
version of Windows and the type of your
PC.
◆ When you use your TV as a PC monitor, it
supports Colours up to 32 bits.
◆ In this case, the display on the TV may look
different depending on your particular
version of Windows or the PC
manufacturer.
◆ When connecting a PC (including the DVI
connection), you must set it to the display
settings that are supported by the TV.
Otherwise, the message Out of input
range will be displayed.
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 63
Input Mode (PC/DVI)
Both screen position and size will vary depending on the type of PC monitor and its resolution.
The table below shows all of the display modes that are supported:
Resolution
(Dot X Line)
Vertical
Frequency(Hz)
Horizontal
Frequency(KHz)
Vertical
Polarity
Horizontal
Polarity
720 X 400
70.087
31.469
P
N
59.940
31.469
N
N
72.809
37.861
N
N
75.000
37.5
N
N
85.008
43.269
N
N
56.250
35.156
N/P
N/P
60.317
37.897
P
P
72.188
48.077
P
P
IBM PC / AT
75.000
46.875
P
P
Compatible
85.061
53.674
P
P
60.004
48.363
N
N
70.069
56.476
N
N
75.029
60.023
P
P
84.997
68.677
P
P
60.020
63.981
P
P
Video Signal
640 X 480
800 X 600
1024 X 768
1280 X 1024
(N: Negative / P: Positive)
◆ The interlace mode is not supported.
◆ The television might operate abnormally if a non-standard video format is selected.
◆ “1280 x 1024” is not available in DVI mode.
Notes
◆ The PC text quality is optimum in XGA mode (1024 x 768@60Hz).
◆ When this television is used as a PC display, 32-bit colour is supported.
◆ Your PC display screen might appear different depending on the manufacturer (and your particular version of
Windows). Check your PC instruction book for information about connecting your PC to a television.
◆ If a vertical and horizontal frequency-select mode exists, select 60Hz (vertical) and 48.3kHz (horizontal).
In some cases, abnormal signals (such as stripes) might appear on the screen when the PC power is turned
off (or if the PC is disconnected). If so, press the SOURCE (
) button to enter the Video mode. Also, make
sure that the PC is connected.
◆ When connecting a notebook PC to the television, make sure that the PC screen is displayed through only the
television (Otherwise, random signals might appear).
◆ When horizontal synchronous signals seem irregular in PC mode, check PC power saving mode or cable
connections.
◆ The Display Settings Table above complies to the IBM/VESA standards, and based on the analog input.
◆ The DVI support mode is regarded as same to the PC support mode.
◆ The best timing for the vertical frequency to each mode is 60Hz.
English - 63
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 64
Pin Configurations
SCART Connector (Ext.1/Ext.2/Ext.3)
➢
Pins 5, 7, 9, 11, 13, 15 and 16 are used for RGB processing and are
only wired on the Ext.1 or Ext.3 connector.
Pin
1
2
3
4
5
6
7
8
9
10
11
Signal
Audio output R
Audio input R
Audio output L
Audio chassis return
Video chassis return (RGB blue)
Audio input L
RGB blue input
Switching voltage
Video chassis return (RGB green)
AV-Link (Ext 1)
RGB green input
PC Input Connector
(15Pin)
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
English - 64
Pin
12
13
14
15
16
17
18
19
20
21
Signal
Video chassis return (RGB red)
RGB red input
Blanking signal (RGB switching)
Video chassis return
Blanking signal ground
Video output
Video input
Screening/chassis return
DVI Input Connector
(24Pin)
PC IN
Red (R)
Green (G)
Blue (B)
Grounding
Grounding (DDC)
Red (R) Grounding
Green (G) Grounding
Blue (B) Grounding
Reserved
Sync Grounding
Grounding
Data (DDC)
Horizontal sync.
Vertical sync.
Clock (DDC)
Pin
Signal
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
T.M.D.S. Data2T.M.D.S. Data2+
T.M.D.S. Data2/4 Shield
T.M.D.S. Data4T.M.D.S. Data4+
Clock (DDC)
Data (DDC)
Not Connected
T.M.D.S. Data1T.M.D.S. Data1+
T.M.D.S. Data1/3 Shield
T.M.D.S. Data3T.M.D.S. Data3+
+5V Power
5V Grounding
Hot Plug Detect
T.M.D.S. Data0T.M.D.S. Data0+
T.M.D.S. Data0/5 Shield
T.M.D.S. Data5T.M.D.S. Data5+
T.M.D.S. Clock Shield
T.M.D.S. Clock+
T.M.D.S. Clock-
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 65
Troubleshooting: Before Contacting Service Personnel
Before contacting Samsung after-sales service, perform the following simple checks.
If you cannot solve the problem using the instructions below, note the model and serial number of the
television and contact your local dealer.
No sound or picture
◆ Check that the mains lead has been connected to a wall socket.
◆ Check that you have pressed the “ I ” button (On/Off) and the
POWER ( ) button.
◆ Check the picture contrast and brightness settings.
◆ Check the volume.
Normal picture but no sound
◆ Check the volume.
◆ Check whether the volume MUTE (
has been pressed.
) button on the remote control
No picture or black and white picture
◆ Adjust the colour settings.
◆ Check that the broadcast system selected is correct.
Sound and picture interference
◆ Try to identify the electrical appliance that is affecting the television,
then move it further away.
◆ Plug your television into a different mains socket.
Blurred or snowy picture,
distorted sound
◆ Check the direction, location and connections of your aerial.
This interference often occurs due to the use of an indoor aerial.
Remote control malfunctions
◆ Replace the remote control batteries.
◆ Clean the upper edge of the remote control (transmission window).
◆ Check the battery terminals.
English - 65
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 66
Programming the Remote Control for Other Components
CABLE CODE LIST
Anvision
GI
Hamlin
Hitachi
Jerrold
Macom
Magnavox
Oak
Panasonic
Philips
Pioneer
RCA
Regal
Regency
SA
Samsung
Scientific Atlanta
Sprucer
Stargate 2000
Sylvania
Texscan
Tocom
Universal
Viewstar
Wamer amex
Zenith
English - 66
017, 018
041
003, 024, 031
025, 030
038, 039
025, 030
019, 023, 028
026
003, 022, 027, 037, 044
019, 021, 023, 028
018, 020, 004, 044
014, 022, 040
003
015, 023
042, 043
000, 001, 002, 003, 004, 005, 006, 007
042, 043
022
036
016
016
032
033, 034
019, 021,023, 028
046
017, 029, 035, 037, 045
DVD CODE LIST
Samsung
Samsung
JVC
PROSCAN, RCA
Panasonic
LG(Goldstar)
Sony
Denon
Curtis Mathes
000
001
002
003
005
006
007
008
009
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 67
Programming the Remote Control for Other Components (continued)
VCR CODE LIST
Admiral
020
Aiwa
025
Akai
027, 004, 032
Audio Dynamics
007, 026
Bell&Howell
018
Broksonic
022
Candle
002, 006, 003, 015, 008, 055
Canon
021, 056
Citizen
002, 006, 003, 015, 008, 055
Colortyme
007
Craig
002, 024
Curtis Mathes 002, 017, 007, 008, 021, 025, 056, 064, 066
Daewoo
003, 015, 010, 011, 012, 013, 014, 016
DBX
007, 026
Dimensia
017
Dynatech
034
Emerson
001, 003, 006, 021, 022, 025, 030, 032, 034,
040, 047, 050, 052, 060, 063, 065, 066, 067, 069
Fisher
018, 024, 028, 029, 048, 051, 061
Funai
025
General Electric
017, 002, 021, 005, 056
Go Video
002
LG(Goldstar)
006, 007, 008, 009, 010
Harman Kardon
007
Hitachi
019, 025, 041, 042
Instant Replay
021
JC Penny
002, 007, 018, 019, 021, 026, 037, 041, 054, 056
JVC
007, 008, 018, 021, 026, 037
Kenwood
007, 008, 018, 026, 037
KLH
070
Lioyd
025
Logik
038
LXI
025
Magnavox
021, 036, 056, 059
Marantz
018, 021, 007, 026, 037, 008, 062, 036
Marta
006
MEI
021
Memorex
006, 021, 024, 025
MGA
034
Midland
005
Minolta
019, 041
Mitsubishi
019, 034, 041, 046
Montgomery Ward
020
MTC
002, 025
Multitech
002, 025, 038, 005
NEC
Optimus
Panasonic
Pentax
Pentex Research
Philco
Philips
Pioneer
Portland
PROSCAN
Quartz
Quasar
Radio Shack/Realistic
018, 007, 026, 037, 008, 062, 064
020
021, 056, 071, 072
019, 041
008
021, 036, 056, 059
021, 036
019, 026, 039, 053
015, 049, 055
017
018
021, 056
006, 018, 020, 021, 024,
025, 029, 034, 048, 056
RCA
017, 019, 002, 021, 035, 041, 043, 057, 068
Samsung
000, 001, 002, 003, 004, 005
Sansui
026
Sanyo
018, 024
Scott
003, 047, 052, 067
Sears
018, 019, 006, 024, 028, 029, 041, 048, 051
Sharp
020, 034, 045, 015
Shimom
027, 033, 038, 058
Signature
025
Sony
027, 033, 044
Sylvania
021, 025, 036, 056, 059
Symphonic
025
Tandy
018, 025
Tashika
006
Tatung
037
Teac
025, 037, 068
Technics
021
Teknika
021, 006, 025, 031
TMK
066
Toshiba
003, 019, 029, 051, 052
Totevision
002, 006
Unitech
002
Vector Research
007, 026
Victor
026
Video Concepts
007, 026
Videosonic
002
Wards
002, 003, 006, 019, 020, 021, 024,
025, 034, 038, 041
Yamaha
007, 008, 018, 026, 037
Zenith
023, 027, 033, 073
English - 67
BN68-00718T-00Eng_1007
10/13/04
9:29 AM
Page 68
- AFTER SALES SERVICE
- Do not hesitate to contact your retailer or service agent
if a change in the performance of your product indicates
that a faulty condition may be present.
ELECTRONICS
BN68-00718T-00
Download PDF