Samsung | 753v | Samsung 753V 사용자 매뉴얼

SyncMaster 750s/753s/753v/753Ms/750Ms
User’s Manual
Index
Main Page
On-Screen Display
Safety Instructions
Troubleshooting
Power
Check List
Installation
Q&A
Cleaning
Self-Test Feature Check
Other
Introduction
Specifications
Unpacking
General Specifications
Front
Preset Display Modes
Rear
PowerSaver
Bottom
Setup
Information
Connecting Your Monitor
Service
Installing the Monitor Driver
Terms
Windows 2000
Regulatory
Other Operating System
Authority
Tilt/Swivel Base Installation
2
User’s Manual
Safety Instructions
Warning / Caution
Failure to follow directions noted by this symbol could result in bodily harm or damage to
equipment.
Notational Conventions
Prohibited
Important to read and understand at all times
Do not disassemble
Disconnect the plug from the outlet
Do not touch
Grounding to prevent an electric shock
3
User’s Manual
4
Safety Instructions
Power
When not used for extended periods of time, set your PC to DPMS. If using a screen saver,
set it to the active screen mode.
If the size of your monitor is small, or if the same image is present for long periods of time,
you may see afterimages due to damage to the flourescent substance on the inside of the
CDT.
● Do not use a damaged or loose plug.
◆ This may cause an electric shock or fire.
● Do not pull the plug out by the wire nor touch the plug with
wet hands.
◆ This may cause an electric shock or fire.
● Use only a properly grounded plug and recepticle.
◆ An improper ground may cause electric shock or equipment damage.
● Do not excessively bend the plug and wire nor place heavy
objects upon them, which could cause damage.
◆ Failure to do so may cause an electric shock or fire.
User’s Manual
Safety Instructions
● Disconnect the plug from the outlet during storms or lightening or if it is
not used for a long period of time.
◆ Failure to do so may cause an electric shock or fire.
● Do not connect too many extension cords or plugs to an outlet.
◆ This may cause a fire.
5
User’s Manual
6
Safety Instructions
Installation
Do not cover the vents on the monitor cabinet.
Bad ventilation may cause a breakdown or fire.
Put your monitor in a location with low humidity and a minimum of dust.
An electric shock or fire could result inside the monitor.
Do not drop the monitor when moving it.
This may cause damage to the product or human body.
Place the monitor on a flat and stable surface.
The monitor can cause injury by falling.
Set down the monitor carefully.
It could be damaged or broken.
Do not place the monitor face down.
The CRT surface may be damaged.
Do not use the monitor without the monitor stand.
It could break down or cause a fire due to bad ventilation.
If the monitor must be used without the supplied stand, take steps to insure proper ventilation.
User’s Manual
Safety Instructions
Cleaning
When cleaning the monitor case or the surface of the CDT, wipe with a slightly
moistened, soft fabric.
Do not clean Flat monitor with water. Use a water-diluted mild detergent.
(Some detergents contain significant amounts of alcohol-based solvents, which can
damage (color change) or crack the monitor case. The antiglare/anti-static surface coating
on the CDT may also be affected.)
Dilute the detergent (1:10 ratio) with water before using.
● Do not spray detergent directly on the monitor.
● Use the recommended detergent with a smooth cloth.
◆ You can prevent the coated CDT from being damaged or the monitor cabinet from
being dissolved, cracked or discolored.
◆ You can buy a recommended detergent at any Samsung Service Center.
Caution : Use a recommended detergent only, as other
surfactants containing large amounts of alcohol,
solvent or other strong substances, can discolor or
crack the monitor or damage the coated CDT
● If the connector between the plug and the pin is dusty or dirty, clean it
properly with a dry cloth.
◆ A dirty connector can cause an electric shock or fire.
● Do not set a glass of water, chemicals or any small metal
objects on the monitor.
◆ This may cause damage, electric shock or a fire.
◆ If a foreign substance gets into the monitor, disconnect the plug
and then contact a service center.
7
User’s Manual
Safety Instructions
Other
● Do not remove cover(or back). No user serviceable parts inside.
◆ This may cause an electric shock or a fire.
◆ Refer servicing to qualified service personnel.
● If your monitor does not operate normally - in particular,if there are any
unusual sounds or smells coming from it - unplug it immediately and
contact an authorized dealer or service.
◆ This may cause an electric shock or a fire.
● Do not place any heavy objects on the monitor.
◆ This may cause an electric shock or a fire.
● For each hour of looking at the monitor, you should let
your eyes rest for 5 minutes.
◆ This will reduce eye fatigue.
● Do not use or store inflammable substances near the monitor.
◆ This may cause an explosion or fire.
● Do not try to move the monitor by pulling on the wire
or the signal cable.
◆ This may cause a breakdown, electric shock or a fire due to damage to the cable.
8
User’s Manual
Safety Instructions
● Do not move the monitor right or left by pulling only the wire
or the signal cable.
◆ This may cause a breakdown, electric shock or a fire due to damage to the cable.
● Never insert anything metallic into the monitor openings.
◆ This may cause an electric shock, fire or injury.
● Keep the monitor away from any magnetic substances.
◆ This may cause discoloring or distortion of the image.
9
User’s Manual
Introduction
Unpacking
Monitor and Stand
Power Cord
Stand
Quick Setup Guide
Warranty card (Not available in all locations)
(Some models include a stand attached.)
Please make sure the following items are
included with your monitor.
If any items are missing, contact your dealer.
User's Guide and Driver Installation CD
USB(Option)
For Multimedia model
Multimedia Speaker Stand
Sound Cables(2each)
DC Power Cord(Option)
User Guide
10
User’s Manual
11
Introduction
Front
1. Exit button
2,3 Adjust buttons
4. Menu button
5. Power indicator
6. Power button
Note:
:
:
:
:
Use this button to Exit the active menu or the OSD.
These buttons allow you to highlight and adjust items in the menu.
Use this button to open the OSD and activate a highlighted menu item.
This light glows green during normal operation, and grows amber
when you are making adjustments.
: Use this button to turn the monitor on and off.
See PowerSaver described in the manual for further information regarding power saving functions.
For energy conservation,turn your monitor OFF when it is not needed,or when leaving it unattended for
long periods.
User’s Manual
12
Introduction
Rear
1. Power port : Connect the power cord for your
monitor to the power port on the back
of the monitor.
2.Signal cable :Connect the end of the signal cable
to your computer's video port
(video board,video card or graphics
card).
Note See Connecting Your Monitor for further information
regarding cable connections.
(The configuration at the back of the moniter
may vary from product to product.)
Bottom
1. Signal cable
: Connect the end of the signal cable to your computer's video port
(video board, video card or graphics card).
2. Power port
: Connect the power cord for your monitor to the power port on the
back of the monitor.
3. Tilt/Swivel Base : You can separate the base from the monitor.
User’s Manual
Setup
Connecting Your Monitor
1. General
1. Connect the power cord for your monitor to the power port on the back of the monitor.
Plug the power cord for the monitor into a nearby outlet.
2. Connect the end of the signal cable to your computer's video port
(video board, video card or graphics card).
3. If you are using a Macintosh computer, connect the cable to a Macintosh adapter, and set
the pins on your adapter(Adapter not included).
A PC-compatible computer does not need an adapter.
Note Turn on your computer and monitor.
If your monitor displays an image, installation is complete.
2. Multimedia
13
User’s Manual
14
Setup
1.Turn off your computer and unplug the power cord.
2.Connect the end of the signal cable to your computer's video port
(video board, video card or graphics card).
3.Connect one end of a sound cable to the Stereo Output jack on your sound card or
computer.Connect the other end of the cable to the Stereo Input jack on the back of the
monitor stand.Connect one end of the other sound cable to the Mic Input jack on your
sound card or computer.Connect the other end of this cable to the Mic By-pass jack
on the back of the nonitor stand.
4.Plug the DC power cord from the stand into a nearby outlet.5. Connect the power cord for
your monitor to the power port on the back of the monitor.
6.Plug the power cord for the monitor and the power cord for your computer into a nearby outlet.
7.Turn on your computer and monitor. If your monitor displays an image,video installation is
complete.
8.Turn up or down the On-Off control terminal on the stand of the monitor until it clicks.
9.Execute a sound program, music or sound effect in your computer and then adjust the
volume by turning up or down until the sound volume is appropriate.
10. Adjust the treble and bass.
Note
Sound distortion may occur when the monitor is placed on top of a mostly hollow
cabinet such as your computer. If this occurs, place a pad or magazine beneath
the monitor stand. High sound volume may also cause sound distortion;
lower the volume.
3. Multimedia Speaker Stand
1.Mic By-pass Jack
To transmit your voice,connect a sound cable from
the Mic By-pass jack to the mic in jack on the sound card
slot in your computer.
2.Stereo Input Jack
Connect a sound cable from the input source
(sound card,computer,CD-ROM drive).
3.DC power Cord
Connect DC power cord to monitor DC 12V output jack.
4.Power Indicator
Glows green when the speakers are turned on.
5.On/Off Volume
Turns On/Off and adjusts the output volume.
6.Treble Control
Use to control high frequencies.
7.Bass Control
Use to control low frequencies.
8.Mic Input Jack
To transmit your voice,connect a microphone to this jack.
9.Headphone Jack
To listen in privacy,connect headphones here.
10.Detachable Stand Top
Setup
When prompted by the operating system for the monitor driver, insert the CD-ROM
included with this monitor. Driver installation is slightly different from one operating
system to another. Follow the directions as appropriate for the operating system you
have.
Prepare a blank disk and download the driver program file at the Internet web site shown
here.
z
Internet web site : http://www.samsung-monitor.com/ (Europe)
http://www.samsungmonitor.com/ (USA)
http://www.sec.co.kr/ (Korea)
http://www.samsungmonitor.com.cn/ (China)
Windows ME/98/95
1. Insert CD into the CD-ROM driver.
2. Click "Windows ME/98/95 Driver".
3. Choose your monitor model in the model list, then click the "OK" button.
4. Click the "Install" button in the "Warning" window.
Setup
Windows XP/2000
1. Insert CD into the CD-ROM driver.
2. Click "Windows XP/2000 Driver".
3. Choose your monitor model in the model list, then click the "OK" button.
4. Click the "Install" button in the "Warning" window.
5. If you can see following "Message" window, then click the "Continue Anyway" button.
Then click "OK" button.
This monitor driver is under certifying MS logo,and this installation don't damage your
system.The certified driver will be posted on Samsung Monitor Homepage
http://www.samsung-monitor.com/.
6. Monitor driver installation is completed.
Setup
When prompted by the operating system for the monitor driver, insert the CD-ROM
included with this monitor. Driver installation is slightly different from one operating
system to another. Follow the directions as appropriate for the operating system you
have.
Prepare a blank disk and download the driver program file at the Internet web site shown
here.
z
Internet web site : http://www.samsung-monitor.com/ (Europe)
http://www.samsungmonitor.com/ (USA)
http://www.sec.co.kr/ (Korea)
http://www.samsungmonitor.com.cn/ (China)
Microsoft® Windows® XP Operating System
1. Insert CD into the CD-ROM driver.
2. Click "Start" —> "Control Panel" then click the "Appearance and Themes" Icon.
3. Click "Display" icon and choose the "Settings" tab then click "Advanced..".
4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab.
Setup
5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button.
6. Select "Don't search ,I will.." then click "Next" and then click "Have disk".
7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the
model list and click the "Next" button.
8. If you can see following "Message" window, then click the "Continue Anyway" button. Then
click "OK" button.
Setup
This
is
your
Thi monitor
it driver
di
i under
d certifying
tif i MS logo,and
l
d this
thi installation
i t ll ti don't
d 't damage
d
system.The certified driver will be posted on Samsung Monitor Homepage
http://www.samsung-monitor.com/.
9. Click the "Close" button then click "OK" button continually.
10. Monitor driver installation is completed.
Microsoft® Windows® 2000 Operating System
When you can see "Digital Signature Not Found" on your monitor, follow these steps.
1. Choose "OK" button on the "Insert disk" window.
2. Click the "Browse" button on the "File Needed" window.
3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button.
How to install
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Click "Start" , "Setting" , "Control Panel".
Double click the "Display" Icon.
Choose the "Settings" tab and then click "Advanced..".
Choose "Monitor".
Case1: If the "Properties" button is inactive, it means your monitor is properly configured.
Please stop installation
Case2: If the "Properties" button is active, click the "Properties" button then follow next
steps continually.
Click "Driver" and then click on "Update Driver.." then click on the "Next" button.
Choose "Display a list of the known drivers for this device so that I can choose a
specific driver" then click "Next" and then click "Have disk".
Click the "Browse" button then choose A:(D:\Driver).
Click the "Open" button, then click "OK" button.
Choose your monitor model and click the "Next" button then click "Next" button.
Click the "Finish" button then the "Close" button.
If you can see the "Digital Signature Not Found" window then click the "Yes"button.
And click the "Finish" button then the "Close" button.
Setup
Microsoft® Windows® Millennium Operating System
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Click "Start" , "Setting" , "Control Panel".
Double click "Display" icon.
Select the "Settings" tab and click "Advanced Properties" button.
Select the "Monitor" tab.
Click the "Change" button in the "Monitor Type" area.
Choose "Specify the location of the driver".
Choose "Display a list of all the driver in a specific location.." then click "Next" button.
Click the "Have Disk" button
Specify A:\(D:\driver) then click "OK" button.
Select "Show all devices" and choose the monitor that corresponds to the one you
connected to your computer and click "OK".
11. Continue choosing "Close" button and "OK" button until you close the Display Properties
dialogue box.
(You can get some other screen for warning message or others, then click the appreciate
option for your monitor.)
Microsoft® Windows® 98 Operating System
1.
2.
3.
4.
5.
6.
7.
8.
9.
Click "Start" , "Setting" , "Control Panel".
Double click "Display" icon.
Select the "Settings" tab and click "Advanced Properties" button.
Select the "Monitor" tab.
Click the "Change" button in the "Monitor Type" area then click "Next" button.
Choose "Display a list of all the driver.." then click "Next" button.
Click the "Have Disk" button, then click "browse.." button.
Specify A:\(D:\driver) then click "OK" button.
The "Select Device" dialogue box will appear. Select "Show all devices" then choose the
monitor that corresponds to the one you connected to your computer and click OK.
10. Continue choosing "Close" button and "O.K" button until you close the Display Properties
dialogue box.
Microsoft® Windows® 95 Operating System
First determine the Windows 95 version installed on your computer by right-clicking the My
Computer icon on PC and selecting Properties. The version number is listed under System.
Perform the steps for the appropriate version.
Version 4.00.950A
1. Click Start, Settings, Control Panel, and then double-click "Display" icon.
2. In the "Display Properties" window, click the "Settings" tab and click "Change Display
Type".
3. In the "Change Display Type" window, click "Change" and then click "Have Disk".
4. Click "browse.." button and specify A:\(D:\driver) and click "OK".
5. In the Select Device window, click the appropriate monitor model and then click OK.
6. Continue choosing "Close" button and "OK" button until you close the "Display
Properties" dialogue box.
Version 4.00.950B
1. Click Start, Settings, Control Panel, and then double-click "Display" icon.
2. In the "Display Properties" window, click the Settings tab and then click "Advanced
Properties" button.
3. In the "Advanced Display Properties" window, click the "Monitor" tab and then click
"Change" button.
4. In the "Select Device" window, click "Have Disk" button.
5. Click "browse.." button and specify A:\(D:\driver) and click "OK".
6. In the "Select Device" window, click the appropriate monitor model and then click "OK".
Setup
7. C
Continue
choosing
"Close"" b
button
button
the "Di
"Display
7
ti
h
i "Cl
tt and
d "OK" b
tt until
til you close
l
th
l
Properties" dialogue box.
Microsoft® Windows® NT Operating System
1. Click Start, Settings, Control Panel, and then double-click Display icon.
2. In Display Registration Information window, click Settings Tab and then click All Display
Modes.
3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency)
and then click OK.
4. Click Apply button if you see the screen working normally after clicking Test. If the screen
is not normal, change to a different mode (lower mode of resolution, colors or frequency).
Note: If there is no Mode at All Display Modes, select the level of resolution and vertical
frequency by referring to the Preset Display Modes in the user guide.
Linux Operating System
To execute X-Window, you need to make the X86Config file, which is a type of system setting
file.
1.
2.
3.
4.
5.
6.
7.
Press Enter at the first and the second screen after executing the X86Config file.
The third screen is for setting your mouse.
Set a mouse for your computer.
The next screen is for selecting a keyboard.
Set a Keyboard for your computer.
The next screen is for setting your monitor.
First of all, set a horizontal frequency for your monitor. (You can enter the frequency
directly.)
8. Set a vertical frequency for your monitor. (You can enter the frequency directly.)
9. Enter the model name of your monitor. This information will not affect the actual
execution of X-Window.
10. You have finished setting up your monitor.
Execute X-Window after setting other requested hardware.
User’s Manual
Setup
Tilt/Swivel Base Installation
1. Tilt/Swivel Base
With the built-in pedestal, you can tilt and/or swivel the monitor for the most comfortable viewing angle.
Note The base is detachable.
20
User’s Manual
Setup
2. Attaching the Base
1. Place the monitor upside-down on a flat
work surface.
2. Align the tabs on the base with the corresponding
slots on the bottom of the monitor.
Do not bend the snap.
3. Press the base onto the monitor until the tabs
are fully engaged in the slots.
4. Push the base toward the front of the monitor
until the release latch clicks into the locked
position.
21
User’s Manual
22
Setup
Removing the Base
5. Squeeze and pull up on the release latch on the base.
6. Push the base toward the back of the monitor and lift up to remove
the base.
Note The Base will align with the monitor slots in only one position.
3. Disconncecting Speaker Cables
1. Turn off your speakers,monitor and computer before removing or connecting cables.
2. Disconnect the sound cables from the Stereo Input jack and the Mic By-pass jack on
the back of the monitor stand and the sound card in your computer.
User’s Manual
On Screen Display (OSD) Menu System
23
User’s Manual
24
On Screen Display (OSD) Menu System
Menu
How to adjust
Brightness
Adjust the Brightness.
With the menu off, push the menu
button.
Push the - button or + button until the Brightness
screen is displayed.
Push the menu
button to open the Brightness adjustment screen.
Use the + button to increase the brightness or - button to decrease the
brightness.
Contrast
Adjust the Contrast.
With the menu off, push the menu
button.
Push the - button or + button until the Contrast
screen is displayed.
Push the menu
button to open the Contrast adjustment screen.
Use the + button to increase the contrast or - button to decrease the
contrast.
User’s Manual
25
On Screen Display (OSD) Menu System
Menu
How to adjust
H-Position
Follow these instructions to change the Position of
the monitor’s entire display.
With the menu off, push the menu
button.
Push the - button or + button until the H-Position screen is
displayed.
Push the menu
button to open the H-Position adjustment screen.
Use the - and + buttons to change the Horizontal
position of the monitor’s viewing area.
V-Position
Follow these instructions to change the Position of
the monitor’s entire display.
With the menu off, push the menu
button.
Push the - button or + button until the V-Position screen is
displayed.
Push the menu
button to open the V-Position adjustment screen.
Use the - and + buttons to change the vertical
position of the monitor’s viewing area.
User’s Manual
26
On Screen Display (OSD) Menu System
Menu
How to adjust
H-Size
Follow these instructions to change the Size of
the monitor’s entire display.
With the menu off, push the menu
button.
Push the - button or + button until the H-Size screen is displayed.
Push the menu
button to open the H-Size adjustment screen.
Use the - and + buttons to change the Horizontal
Size of the monitor’s viewing area.
V-Size
Follow these instructions to change the Size of
the monitor’s entire display.
With the menu off, push the menu
button.
Push the - button or + button until the V-Size screen is displayed.
Push the menu
button to open the V-Size adjustment screen.
Use the - and + buttons to change the Vertical
Size of the monitor’s viewing area
User’s Manual
27
On Screen Display (OSD) Menu System
Menu
How to adjust
Pincushion
Adjust the pincushion setting when the sides of the display
are bowed in or bowed out
With the menu off, push the menu
button.
Push the - button or + button until the Pincushion
screen is displayed.
Push the menu
button to open the Pincushion
adjustment screen.
Use the - button or + button to adjust the pincushion setting.
Trapezoid
Adjust the trapezoid setting when the top or bottom of the
display is too large or small.
With the menu off, push the menu
button.
Push the - button or + button until the Geometry
screen is displayed.
Push the menu
button again and then press the - or + button until
the Trapezoid screen appears.
Push the menu
button to open the Trapezoid adjustment screen.
Use the - button or + button to adjust the trapezoid setting.
User’s Manual
28
On Screen Display (OSD) Menu System
Menu
How to adjust
Parallelogram
Adjust the parallelogram setting when the display is leaning
left or right.
With the menu off, push the menu
button.
Push the - button or + button until the Geometry
screen is displayed.
Push the menu
button again and then press the - or + button until
the Parallelogram screen appears.
Push the menu
button to open the Parallelogram
adjustment screen.
Use the - button or + button to adjust the parallel setting.
Rotation
Adjust the rotation setting when the entire display
is tilted left or right.
With the menu off, push the menu
button.
Push the - button or + button until the Geometry
screen is displayed.
Push the menu
button again and then press the - or + button until
the Rotation screen appears.
Push the menu
button to open the Rotation
adjustment screen.
Use the - button or + button to adjust the rotation setting.
User’s Manual
29
On Screen Display (OSD) Menu System
Menu
How to adjust
Pinbalance
Adjust the pinbalance setting when the sides of the display are
bowed towards the left or right.
With the menu off, push the menu
button.
Push the - button or + button until the Geometry
screen is displayed.
Push the menu
button again and then press the - or + button until
the Pinbalance screen appears.
Push the menu
button to open the Pinbalance
adjustment screen.
Use the - button or + button to adjust the pinbalance setting.
V-Linearity
Adjust the linearity setting when the display image is
compressed at the left, right or top, bottom.
With the menu off, push the menu
button.
Push the - button or + button until the Geometry
screen is displayed.
Push the menu
button.
Push the - button or + button until the V-Linearity
screen is displayed.
Push the menu
button to open the V-Linearity adjustment screen.
Use the - button or + button to adjust the vertical linearity.
User’s Manual
30
On Screen Display (OSD) Menu System
Menu
How to adjust
Language
Follow these steps to change the language used in the menu.
You can choose one of ten languages.
English,German,French, Italian, Portuguese, Spanish, Swedish,
Russian, Polish, or Magyar.
(Some OSD languages may not appear in some areas.)
With the menu off, push the menu
button.
Push the - button or + button until the Language
screen is displayed.
Push the menu
button to open the Language selection screen.
Use the - button or + button to select the language you would like to
use.
Note The language chosen affects only the language of the
OSD. It has no effect on any software running on the
computer.
User’s Manual
31
On Screen Display (OSD) Menu System
Menu
How to adjust
H-Moire
A “Moiré” pattern can appear on your screen, looking like a
series of concentric circles or arcs. To eliminate this pattern,
use the clear moiré adjustments.
With the menu off, push the menu
button.
Push the - button or + button until the Advanced
screen is displayed.
Push the menu
button again and then press the - or + button until
the H-Moire screen appears.
Push the menu
button to open the H-Moire
adjustment screen.
Use the - button or + button to adjust horizontal moiré.
V-Moire
A “Moiré” pattern can appear on your screen, looking like a
series of concentric circles or arcs. To eliminate this pattern,
use the clear moiré adjustments.
With the menu off, push the menu
button.
Push the - button or + button until the Advanced
screen is displayed.
Push the menu
button again and then press the - or + button until
the V-Moire screen appears.
Push the menu
button to open the V-Moire
adjustment screen.
Use the - button or + button to adjust vertical moiré.
User’s Manual
32
On Screen Display (OSD) Menu System
Menu
How to adjust
Video Input Level
Some video cards use video signals higher than 1.0V which
causes the display to be very bright. For those video cards,
use this feature to select the 1.0V Level.
With the menu off, push the menu
button.
Push the - button or +button until the Advanced
screen is displayed.
Push the menu
button again and then press the - or + button until
the Video Input Level screen appears.
Push the menu
button to open the Video Input Level
selection screen.
Use the - button or + button to select 0.7 V or 1.0 V.
Color Temperature
Color temperature is a measure of the “warmth” of the image
colors. The available range is between 6500 to 9300K.
With the menu off, push the menu
button.
Push the - button or + button until the Advanced
screen is displayed.
Push the menu
button again and then press the - or + button until
the Color Temperature screen appears.
Push the menu
button to open the Color Temperature selection
screen.
Press the - or + button to select 9300K(Bluish colors)
or 6500K(Reddish colors).
User’s Manual
33
On Screen Display (OSD) Menu System
Menu
How to adjust
Zoom
Follow these instructions to get a close-up or a longshot view
of the monitor’s viewing area.
With the menu off, push the menu
button.
Push the - button or + button until the Zoom
screen is displayed.
Push the menu
button to open the Zoom adjustment screen.
Use the - button to decrease the screen viewing area.
Use the + button to enlarge the screen viewing area.
User’s Manual
34
On Screen Display (OSD) Menu System
Menu
How to adjust
Degauss
The Degauss feature will remove color impurities caused by
magnetic fields.
You can use this function to turn on the power of the monitor
or change the power saving mode to the normal mode.
Do not use the Degauss feature more than once within a
30-minute period.
With the menu off, push the menu
button.
Push the - button or + button until the Degauss
screen is displayed.
Push the menu
button to execute the degauss function.
The degaussing screen will appear.
Note The monitor may buzz momentarily, the image colors may
change and the image will jiggle for a few seconds.
These effects are normal.
Recall
Use the recall feature to reset these monitor settings to their
original levels: Position, Size, Pincushion, Trapezoid,
Parallelogram, Pinbalance, Rotation, H-Moire and V-Moire.
With the menu off, push the menu
button.
Push the - button or + button until the Recall
screen is displayed.
Push the menu
button to open the Recall adjustment screen.
Push the + button to select Yes.
If you don’t want to reset the monitor, use the - button to select No.
Note If you have selected “Yes”, all settings listed above will be
reset. All other settings will remain the same.
CAUTION This operation resets all of the data in the user memory
area for the current timing signal.
User’s Manual
35
On Screen Display (OSD) Menu System
Menu
How to adjust
Display Timing
The information on this screen shows Display Timing , User
Timing and Factory Timing.
With the menu off, push the menu
button.
Push the - button or + button until the Display Timing
screen is displayed.
Push the menu
button to open the Display Timing adjustment screen.
Use the - button to see user control mode and thedefault mode.
Note You can see the frequency(user control mode) used by the user,
the polarity of the operational signals, the default frequency(default mode)
set when you buy the monitor and the resolution level.
OSD Lock/Unlock
Push and hold in the menu
button for 10 seconds or more
to Lock the OSD.
(In this case, even if you click the menu
button the control
screen will not be printed.)
Push and hold in the menu
to Unlock the OSD.
button for 10 seconds or more
User’s Manual
Troubleshooting
Chek List
Note Before calling for service, check the information in this section to see if you can solve the problem yourself.
If you do need assistance, please call the phone number on the warranty card, the phone number on
the Information section or contact your dealer.
1. General
Symptom
Chek List
Solution
Is the power cord connected
properly?
Check the power cord connection and
supply.
Can you see "No Connection, Check
Signal Cable" on the screen?
Check the signal cable connection.
If the power is on, reboot the
computer to see the initial
screen(the login screen),
which can be seen.
If the initial screen (the login screen)
appears, boot the computer in the
applicable mode (the safe mode for
Windows 98/95) and then change the
frequency of the video card.(Refer to
the Preset Display Modes)
Note: If the initial screen (the login
screen) does not appear,
contact a service center or
your dealer.
Can you see "Sync. Out of Range"
on the screen?
You can see this message when the
signal from the video card exceeds the
maximum resolution and frequency that
the monitor can properly handle.
Adjust the maximum resolution and
frequency applicable to the monitor.
There is no image on the screen.Is
the power indicator on the monitor
blinking at 1 second intervals?
Have you locked the On Screen
Display (OSD) Menu to prevent
changes?
The monitor is in PowerSave mode.
Press a key on the keyboard or move
the mouse to activate the monitor and
restore the image on the screen.
Unlock the OSD by pressing the MENU
button for at least 10 seconds.
36
User’s Manual
Troubleshooting
Symptom
Chek List
Solution
Check the monitor configuration to
see if it is in Interlace Mode.
(Interlace Mode: Vertical frequency
43Hz, 87Hz(i), etc)
The signal from the video card
exceeds the maximum resolution
and frequency of the monitor.
Are there any magnetic products
such as a high voltage wire near by?
Move the monitor away from
anything that can create a strong
magnetic field.
Is the voltage stable?
The screen image can appear to
shake or vibrate at a particular time
of day due to low supply voltage.
The screen image can also appear to shake or vibrate if there is a problem with the video
card or the computer's main board.
Is the screen displaying only one
color as if looking at the screen
through a cellophane paper?
Check the signal cable connection.
Have the screen colors become
strange after running a program or due
to a crash between applications?
Reboot the computer.
Has the video card been set properly?
Set the video card by referring to the
video card manual.
Have you changed the video card or
the driver?
Adjust screen image position and
size using the OSD.
Have you adjusted the resolution or
frequency to the monitor?
Adjust the resolution and frequency
at the video card.
(Refer to the Preset Display Modes).
Make sure the video card is fully
inserted in it's slot.
The screen can be unbalanced due to the cycle of the video card signals.
Readjust Position by referring to the OSD.
Have you adjusted the resolution or
frequency on the monitor?
Adjust the resolution and frequency of
the video card.
(Refer to the Preset Display Modes).
37
User’s Manual
Troubleshooting
Symptom
Chek List
Solution
Are there any magnetic products such
as an adapter, speaker or a high
voltage wire near the monitor?
Enter the OSD and perform a
'Degauss'.
Is the frequency properly adjusted
when checking the Display Timing
on the menu?
Adjust the frequency properly by
referring to the video card manual
and the Preset Display Modes.
Keep the monitor away from any
magnetic products.
(The maximum frequency per
resolution may differ from product to
product.)
Have the Windows colors been set
properly?
For Windows 98(95):
Set the colors properly at the Control
Panel, Display, Settings.
For Windows 3.1:
Adjust the colors of the screen using
the VGA utility provided by the video
card.
Has the video card been set
properly?
Set the video card by referring to the
video card manual.
Have you installed the monitor
driver?
Install the monitor driver according to
the Driver Installation Instructions.
See the video card manual to see if
the Plug & Play (VESA DDC)
function can be supported.
Install the monitor driver according to
the Driver Installation Instructions.
38
User’s Manual
Troubleshooting
2. Multimedia
Symptom
Solution
There is no sound.
Connect the stereo input jack of the monitor to the stereo output jack of the
computer thoroughly by using the voice cable or adjust the volume.
The sound is
too weak.
Turnthe volume up to MAX.
If the sound is still too weak even after setting the volume on MAX,
adjust the volume of the sound card or software program in your computer.
The sound is too
sharp.
Turn the volume slightly down.
If using an extensive microphone, adjust the volume while keeping a certain
distance from the speaker.
The sound is too
thick.
The microphone is
not working.
Re-adjust Bass and Treble.
The sound is
distorted.
Turn the volume down.
Place a magazine or a pad under the stand of your monitor.
Check to see if the connection cord of the microphone is connected properly
and then try again.
The sound card in your computer should support the microphone input
function. Otherwise, change your sound card or use a microphone provided
with your computer.
Check the following items if there is trouble with the monitor.
1. Check if the power cord and the cable are properly connected to the computer.
2. Check if the computer beeps more than 3 times when booting.
(If it does, request an after-service for the main board of the computer.)
3. If you installed a new video card or if you assembled the PC, check if the installed the adapter
(video) driver and the monitor driver.
4. Check if the scanning ratio of the video screen is set at 75Hz or 85Hz.
(Do not exceed 60Hz when using the maximum resolution.)
5. If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode,
remove the Display Adapter at the “Control Panel, System, Device Administrator" and then
reboot the computer to reinstall the adapter (video) driver.
Note If problems repeatedly occur, contact an authorized service center.
39
User’s Manual
Troubleshooting
Q&A
Question
How can I change the
frequency?
Answer
Frequency can be changed by reconfiguring the video card.
Note that video card support can vary, depending on the version of the
driver used.
(Refer to the computer or the video card manual for details.)
How can I adjust the resolution?
Windows 95/98: Set the resolution at the Control Panel,
Display, Settings.
Windows 3.1: Change the resolution and the colors
using the VGA Utility provided by the video card.
* Contact the video card manufacturer for details.
How can I set the Power
Saving function?
Windows 95/98: Set the function at BIOS-SETUP of the computer or the
screen saver. (Refer to Windows/Computer Manual).
Windows 3.1: Set the function using the VGA Utility
provided by the video card.
The monitor makes a sound when it
is turned on.
This is normal as some sound may be generated when the metal case and
the electromagnet, which are installed to block any electromagnetic waves,
interact with each other.
How can I clean the outer
case/Picture tube?
Disconnect the power cord and then clean the monitor with a soft cloth,
using either a plain water.
Do not leave any remains of the detergent nor scratch the case. Do not
allow any water to go inside the monitor.
40
User’s Manual
Troubleshooting
Self-Test Feature Check
A self-test feature is provided that allows you to check for proper monitor function. If your monitor and
computer are properly connected but the monitor screen remains dark and the power indicator is blinking, run
the monitor self-test by performing the following steps:
Self-Test Feature Check
1. Turn off both your computer and the monitor.
2. Unplug the video cable from the back of the computer.
3. Turn on the monitor.
If your monitor is functioning properly, you will see a box with a blue border and red text
inside as shown in the following illustration:
The three boxes inside the border are red, green and blue.
Failure of any of the boxes to appear indicates a problem with your monitor. This box
also appears during normal operation if the video cable becomes disconnected or
damaged.
4.Turn off your monitor and reconnect the video cable; then turn on both your
computer and the monitor.
If your monitor screen remains blank after using the previous procedure,
check your video controller and computer system; your monitor is functioning properly.
41
User’s Manual
42
Troubleshooting
Self-Test Feature Check
Warning Messages
If there is something wrong with the input signal, a message appears on the screen or the screen goes blank
although the power indicator LED is still on. The message may indicate that the monitor is out of scan range or that
you need to check the signal cable.
Environment
The location and the position of the monitor may influence the quality and other features of the monitor.
1. If there are any woofer speakers near the monitor, unplug and relocate the
woofer to another room.
2. Remove all electronic devices such as radios, fans, clocks and telephones that
are within 3 feet (one meter) of the monitor.
3. Degauss the monitor if any devices were removed from the area.
Userful Tip
A monitor recreates visual signals received from the PC. Therefore, if there is trouble with the PC or the video card, this can
cause the monitor to become blank, have poor coloring, noise, Sync. Out of Range, etc. In this case, first check the source
of the problem, and then contact a service center or your dealer.
Judging the monitor's working condition
If there is no image on the screen or an "Sync. Out of Range" message comes up, disconnect the cable from
the computer while the monitor is still powered on.
If there is a message coming up on the screen or if the screen goes white, this means the monitor is in
working condition.
In this case, check the computer for trouble.
User’s Manual
Specifications
General Specifications
General
Model Name
Picture Tube
Type
Deflection angle
Dot Pitch
Screen type
SyncMaster 750s
17" (43cm) Full square type(40.6cm viewable)
90°
0.23 mm(Horizontal)
Aluminized tri-color phosphor dot trio with black matrix.
Anti-doming invar shadow mask. Multi-layer coated with anti-static.
Maximum Resolution
1280 Dots, 1024 Lines at 65Hz
Active Display
Horizontal
312 ± 4 mm
Vertical
234 ± 4 mm
Synchronization
Horizontal
30 ~ 70kHz
Vertical
50 ~ 160 Hz
Input Signal Definition
Video Signal
RGB, Analog 0.7 Vpp positive at 75ohms
Sync Signal
Separate H/V sync, TTL level, Positive or Negative
Display Color
Unlimited
Maximum Pixel Clock
110MHz
Power Supply
90 ~ 264VAC rms, 60/50 Hz ± 3Hz
Power Consumption
90 W(Max.), 80 W(Nom.)
Dimensions (WxDxH)
398x 412 x 400mm (with stand)
Weight
15 kg
Environmental Considerations
Operating Temperature 32 F ~ 104 F (0 ~ 40 )
Humidity
10% ~ 80%, non-condensing
Storage Temperature -4 F ~ 113 F (-20 ~ -45 )
Humidity
5% ~ 95%, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and
computer systems will provide the best operating conditions and monitor settings. In most cases,
monitor installation will proceed automatically, unless the user wishes to select alternate settings.
43
User’s Manual
Specifications
General Specifications
General
Model Name
Picture Tube
Type
Deflection angle
Dot Pitch
Screen type
SyncMaster 753s
17" (43cm) Full square type(40.6cm viewable)
90°
0.23 mm(Horizontal)
Aluminized tri-color phosphor dot trio with black matrix.
Anti-doming invar shadow mask. Multi-layer coated with anti-static.
Maximum Resolution
1280 Dots, 1024 Lines at 65Hz
Active Display
Horizontal
312 ± 4 mm
Vertical
234 ± 4 mm
Synchronization
Horizontal
30 ~ 70kHz
Vertical
50 ~ 160 Hz
Input Signal Definition
Video Signal
RGB, Analog 0.7 Vpp positive at 75ohms
Sync Signal
Separate H/V sync, TTL level, Positive or Negative
Display Color
Unlimited
Maximum Pixel Clock
110MHz
Power Supply
90 ~ 264VAC rms, 60/50 Hz ± 3Hz
Power Consumption
90 W(Max.), 80 W(Nom.)
Dimensions (WxDxH)
398x 412 x 400mm (with stand)
Weight
15 kg
Environmental Considerations
Operating Temperature 32 F ~ 104 F (0 ~ 40 )
Humidity
10% ~ 80%, non-condensing
Storage Temperature -4 F ~ 113 F (-20 ~ -45 )
Humidity
5% ~ 95%, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and
computer systems will provide the best operating conditions and monitor settings. In most cases,
monitor installation will proceed automatically, unless the user wishes to select alternate settings.
44
User’s Manual
Specifications
General Specifications
General
Model Name
Picture Tube
Type
Deflection angle
Dot Pitch
Screen type
SyncMaster 753v
17" (43cm) Full square type(40.6cm viewable)
90°
0.23 mm(Horizontal)
Aluminized tri-color phosphor dot trio with black matrix.
Anti-doming invar shadow mask. Glare
Maximum Resolution
1280 Dots, 1024 Lines at 65Hz
Active Display
Horizontal
312 ± 4 mm
Vertical
234 ± 4 mm
Synchronization
Horizontal
30 ~ 70kHz
Vertical
50 ~ 160 Hz
Input Signal Definition
Video Signal
RGB, Analog 0.7 Vpp positive at 75ohms
Sync Signal
Separate H/V sync, TTL level, Positive or Negative
Display Color
Unlimited
Maximum Pixel Clock
110MHz
Power Supply
90 ~ 264VAC rms, 60/50 Hz ± 3Hz
Power Consumption
90 W(Max.), 80 W(Nom.)
Dimensions (WxDxH)
398x 412 x 400mm (with stand)
Weight
15 kg
Environmental Considerations
Operating Temperature 32 F ~ 104 F (0 ~ 40 )
Humidity
10% ~ 80%, non-condensing
Storage Temperature -4 F ~ 113 F (-20 ~ -45 )
Humidity
5% ~ 95%, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and
computer systems will provide the best operating conditions and monitor settings. In most cases,
monitor installation will proceed automatically, unless the user wishes to select alternate settings.
45
User’s Manual
Specifications
General Specifications
General
Model Name
Picture Tube
Type
Deflection angle
Dot Pitch
Screen type
SyncMaster 753Ms
17" (43cm) Full square type(40.6cm viewable)
90°
0.23 mm(Horizontal)
Aluminized tri-color phosphor dot trio with black matrix.
Anti-doming invar shadow mask. Multi-layer coated with anti-static.
Maximum Resolution
1280 Dots, 1024 Lines at 65Hz
Active Display
Horizontal
312 ± 4 mm
Vertical
234 ± 4 mm
Synchronization
Horizontal
30 ~ 70kHz
Vertical
50 ~ 160 Hz
Input Signal Definition
Video Signal
RGB, Analog 0.7 Vpp positive at 75ohms
Sync Signal
Separate H/V sync, TTL level, Positive or Negative
Display Color
Unlimited
Maximum Pixel Clock
110MHz
Power Supply
90 ~ 264VAC rms, 60/50 Hz ± 3Hz
Power Consumption
100 W(Maximum, Speaker on), 80 W(Nominal)
Dimensions (WxDxH)
398x 412 x 400mm (with stand)
Weight
15 kg
Environmental Considerations
Operating Temperature 32 F ~ 104 F (0 ~ 40 )
Humidity
10% ~ 80%, non-condensing
Storage Temperature -4 F ~ 113 F (-20 ~ -45 )
Humidity
5% ~ 95%, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and
computer systems will provide the best operating conditions and monitor settings. In most cases,
monitor installation will proceed automatically, unless the user wishes to select alternate settings.
46
User’s Manual
Specifications
General Specifications
Multimedia Speaker Stand
Out Power Continuous(RMS)
3.0 Watt at 10% THD
S/N(;Signal to Noise) Ratio
55dB
Input Level
500mV
Frequency Response
180 Hz ~ 20,000Hz
Power Supply
DC(Adapter) 12V/1A
Design and specifications are subject to change without prior notice
47
User’s Manual
Specifications
General Specifications
General
Model Name
Picture Tube
Type
Deflection angle
Dot Pitch
Screen type
SyncMaster 750Ms
17" (43cm) Full square type(40.6cm viewable)
90°
0.23 mm(Horizontal)
Aluminized tri-color phosphor dot trio with black matrix.
Anti-doming invar shadow mask. Multi-layer coated with anti-static.
Maximum Resolution
1280 Dots, 1024 Lines at 65Hz
Active Display
Horizontal
312 ± 4 mm
Vertical
234 ± 4 mm
Synchronization
Horizontal
30 ~ 70kHz
Vertical
50 ~ 160 Hz
Input Signal Definition
Video Signal
RGB, Analog 0.7 Vpp positive at 75ohms
Sync Signal
Separate H/V sync, TTL level, Positive or Negative
Display Color
Unlimited
Maximum Pixel Clock
110MHz
Power Supply
90 ~ 264VAC rms, 60/50 Hz ± 3Hz
Power Consumption
100 W(Maximum, Speaker on), 80 W(Nominal)
Dimensions (WxDxH)
398x 412 x 400mm (with stand)
Weight
15 kg
Environmental Considerations
Operating Temperature 32 F ~ 104 F (0 ~ 40 )
Humidity
10% ~ 80%, non-condensing
Storage Temperature -4 F ~ 113 F (-20 ~ -45 )
Humidity
5% ~ 95%, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and
computer systems will provide the best operating conditions and monitor settings. In most cases,
monitor installation will proceed automatically, unless the user wishes to select alternate settings.
48
User’s Manual
Specifications
General Specifications
Multimedia Speaker Stand
Out Power Continuous(RMS)
3.0 Watt at 10% THD
S/N(;Signal to Noise) Ratio
55dB
Input Level
500mV
Frequency Response
180 Hz ~ 20,000Hz
Power Supply
DC(Adapter) 12V/1A
Design and specifications are subject to change without prior notice
49
User’s Manual
50
Specifications
SyncMaster 750s/753s/753v/753Ms/750Ms
Preset Display Modes
If the signal transferred from the computer is the same as the following Preset Display Modes, the
screen will be adjusted automatically. However, if the signal differs, the screen may go blank while
the power LED is on. Refer to the video card manual and adjust the screen as follows.
Display Mode
Horizontal Frequency
(kHz)
Vertical Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM, 640 x 480
31.469
59.940
25.175
-/-
IBM, 720 x 400
31.469
70.087
28.322
-/+
VESA, 640 X 480
37.500
75.000
31.500
-/-
VESA, 640 X 480
43.269
85.008
36.000
-/-
VESA, 800 X 600
46.875
75.000
49.500
+/+
VESA, 800 X 600
53.674
85.061
56.250
+/+
VESA, 1024 X 768
60.023
75.029
78.750
+/+
VESA, 1024 x 768
68.677
84.997
94.500
+/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen
horizontally is called Horizontal Cycle and the inverse number of the Horizontal
Cycle is called Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per
second to display an image to the user. The frequency of this repetition is called
Vertical Frequency or Refresh Rate. Unit: Hz
User’s Manual
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves
energy by switching your monitor into a low-power mode when it has not been used for a certain
amount of time. The monitor automatically returns to normal operation when you move the
computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor
OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver
system operates with a VESA DPMS compliant video card installed in your computer.
Use a software utility installed on your computer to set up this feature.
SyncMaster 750s/753s/753v
State
Normal Operation
Power Indicator
Green
Power Consumption
80W (Nominal)
Poweer- off mode EPA/ ENERGY 2000
Green, Blinking
Lass than 3W
90W (Maximum)
This monitor is EPA ENERGY STAR R compliant and ENERGY2000 compliant
when used with a computer equipped with VESA DPMS functionality.
As an ENERGY STAR R Partner, SAMSUNG has determined that this product
meets the ENERGY STAR R guidelines for energy efficiency.
51
User’s Manual
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves
energy by switching your monitor into a low-power mode when it has not been used for a certain
amount of time. The monitor automatically returns to normal operation when you move the
computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor
OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver
system operates with a VESA DPMS compliant video card installed in your computer.
Use a software utility installed on your computer to set up this feature.
SyncMaster 753Ms/750Ms
Normal Operation
State
Power Indicator
Green
Power Consumption
80W (Nominal)
Poweer- off mode EPA/ ENERGY 2000
Green, Blinking
Lass than 3W
100W (Maximum,Speaker on)
This monitor is EPA ENERGY STAR R compliant and ENERGY2000 compliant
when used with a computer equipped with VESA DPMS functionality.
As an ENERGY STAR R Partner, SAMSUNG has determined that this product
meets the ENERGY STAR R guidelines for energy efficiency.
52
User’s Manual
53
Information
Service
● U.S.A.
Samsung Computer Products Customer Service 400 Valley Road,
Suite 201, Mt. Arlington, NJ 07856
Tel. : (973)601-6000, 1-800-SAMSUNG (1-800-726-7864)
Fax. : (973)601-6001
http://samsungmonitor.com/
● BRAZIL
Samsung Eletronica da Amazonia Ltda.R. Prof. Manoelito de Ornellas, 303, Terro B
Chacara Sto. Antonio, CEP : 04719-040
Sao Paulo, SP SAC : 0800 124 421
http://www.samsung.com.br/
● CANADA
Samsung Electronics Canada Inc. 7037 Financial Drive Mississauga, Ontario L5N 6R3
Tel. : 1-800-SAMSUNG (1-800-726-7864)
Fax. : (905) 542-1199
http://www.samsung.ca
● COLOMBIA
Samsung Electronics Colombia
Cra 9 No 99A-02 Of. 106 Bogota, Colombia
Tel.: 9-800-112-112
Fax: (571) 618 – 2068
http://www.samsung-latin.com/
e-mail : soporte@samsung-latin.com
● PANAMA
Samsung Electronics Latinoamerica( Z.L.) S.A. Calle 50 Edificio Plaza Credicorp,
Planta Baja Panama
Tel. : (507) 210-1122, 210-1133
Tel : 800-3278(FAST)
http://www.samsung-latin.com/
● PERU
Servicio Integral Samsung Av.Argentina 1790 Lima1. Peru
Tel: 51-1-336-8686
Fax: 51-1-336-8551
http://www.samsungperu.com
● GERMANY
TELEPLAN Rhein-Main GmbH Feldstr. 16
64331 Weiterstadt
T. 06151/957-1306
F. 06151/957-1732
http://www.samsung.de/
● AUSTRALIA
Samsung Electronics Australia Pty Ltd.
Customer Response Centre 7 Parkview Drive, Homebush Bay NSW 2127
Tel : 1300 362 603
http://www.samsung.com.au/
● ITALY
Samsung Electronics Italia SpA
Via C. Donat Cattin, 5-20063 Cernusco sul Naviglio (Mi)
Tel. : 167-010740
http://www.samsung-italia.com
● ESPAÑA
Samsung Electronics Comercial Iberica, S.A.
Ciencies, 55-65 (Poligono Pedrosa) 08908
Hospitalet de Llobregat (Barcelona)
Tel. : (93) 261 67 00
Fax. : (93) 261 67 50
http://samsung.es/
● United Kingdom
Samsung Electronics (UK) Ltd.
Samsung House, 225 Hook Rise South
Surbiton, Surrey KT6 7LD
Tel. : (0208) 391 0168
Fax. : (0208) 397 9949
<European Service Center & National Service>
Stafford Park 12 Telford, Shropshire, TF3 3BJ
Tel. : (0870) 242 0303
Fax. : (01952) 292 033
http://samsungservice.co.uk/
● SOUTH AFRICA
Samsung Electronics,5 Libertas Road, Somerset Office Park, Bryanston Ext
16. Po Box 70006, Bryanston,2021, South Africa
Tel : 0027-11-549-1621
Fax : 0027-11-549-1629
http://www.samsung.co.za
● UKRAINE
SAMSUNG ELECTRONICS REPRESENTATIVE OFFICE
IN UKRAINE 4 Glybochitska str. Kiev, Ukraine
Tel. 8-044-4906878
Fax 8-044-4906887
Toll-free 8-800-502-0000
www.samsung.com.ua
● SWEDEN/DENMARK/NORWAY/FINLAND
Samsung Electronics AB Box 713
S-194 27 UPPLANDS VÄSBY
SVERIGE
Besöksadress : Johanneslundsvägen 4
Samsung support Sverige: 020-46 46 46
Samsung support Danmark : 8088-4646
Samsung support Norge: 8001-1800
Samsung support Finland: 0800-118001
Tel +46 8 590 966 00
Fax +46 8 590 966 50
http://www.samsung.se
● HUNGARY
Samsung Electronics Magyar Rt. 1039, Budapest, Lehel u. 15-17.
Tel: 36 1 453 1100
Fax: 36 1 453 1101
http://www.samsung.hu
● FRANCE
SAMSUNG ELECTRONICS FRANCE Service Paris Nord 2
66 rue des Vanesses BP 50116 Villepinte 95950 Roissy CDG Cedex
Tel : 08 25 08 65 65
Fax : 01 48 63 06 38
http://www.samsungservices.com
● PORTUGAL
SAMSUNG ELECTRONICA PORTUGUESA S.A.
Rua Mário Dioniso, N 2 - 1 Drt. 2795-140 LINDA-A-VELHA
Tel. 214 148 114/100 Fax. 214 148 133/128 Free Line 800 220 120
http://www.samsung.pt/
● NETHERLANDS/BELGIUM/LUXEMBOURG
Samsung Electronics Benelux B. V.
Fleminglaan 12 2289 CP Rijiswijk, NEDERLANDS Service and informatielijn ;
Belgium :0800-95214, http://www.samsung.be/
Netherlands : 0800-2295214, http://www.samsung.nl/
● CHILE
SONDA S.A.
Teatinos 550, Santiago Centro, Santiago, Chile
Fono: 56-2-5605000 Fax: 56-2-5605353
56-2-800200211
http://www.sonda.com/
http://www.samsung.cl/
● MEXICO
Samsung Electronics Mexico S.A. de C.V.Saturno 44 Col.
Nueva Industrial Vallejo Del. Gustavo A. Madero C.P. 07700 Mexico D.F.
Tel. 01 57 47 51 00
Fax. 01 57 47 52 02
RFC: SEM950215S98
http://www.samsung.com.mx/
IMPORTADO POR :
● THAILAND
HAI SAMSUNG SERVICE CENTER MPA COMPLEX BUILDING,1st-2nd
Floor 175 SOI SUEKSA VIDHAYA SATHON SOI 12 SILOM ROAD ,
SILOM,BANGRAK
BANGKOK 10500
TEL : 0-2635-2567
FAX : 0-2635-2556
EXPORTADO POR :
SAMSUNG ELECTRONICS MEXICO S.A. DE C.V.
SATURNO 44 COL. NVA. INDUSTRIAL VALLEJO
DEL. GUSTAVO A. MADERO C.P. 07700
MEXICO D.F. TEL. 5747-5100
RFC: SEM950215S98
SAMSUNG ELECTRONICS CO.,LTD.
JOONG-ANG DAILY NEWS BLDG.
7 SOON-WHA-DONG CHUNG-KU,
C.P.O BOX 2775, 1144 SEOUL, KOREA
User’s Manual
Information
Terms
● Dot Pitch
The image on a monitor is composed of red, green and blue dots. The closer the dots,
the higher the resolution. The distance between two dots of the same color is
called the 'Dot Pitch'. Unit: mm
● Vertical Frequency
The screen must be redrawn several times per second in order to create and display
an image for the user. The frequency of this repetition per second is called Vertical Frequency or
Refresh Rate. Unit: Hz
Example:
If the same light repeats itself 60 times per second, this is regarded as 60 Hz.
In this case, flickering of the screen can be detected. To avoid this problem,
there is a Flicker-free Mode using a vertical frequency over 70 Hz.
● Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen
horizontally is called Horizontal Cycle. The inverse number of the Horizontal Cycle
is called Horizontal Frequency. Unit: kHz
● Interlace and Non-Interlace Methods
Showing the horizontal lines of the screen from the top to the bottom in order is called
the Non-Interlace method while showing odd lines and then even lines in turn is
called the Interlace method. The Non-Interlace method is used for the majority of monitors to
ensure a clear image. The Interlace method is the same as that used in TVs.
● Plug & Play
This is a function that provides the best quality screen for the user by allowing
the computer and the monitor to exchange information automatically. This monitor
follows the international standard VESA DDC for the Plug & Play function.
● Resolution
The number of horizontal and vertical dots used to compose the screen image is called 'resolution'.
This number shows the accuracy of the display. High resolution is good for performing multiple tasks
as more image information can be shown on the screen.
Example: If the resolution is 1024 X 768, this means the screen is composed of
1024 horizontal dots (horizontal resolution) and 768 vertical lines
(vertical resolution).
54
User’s Manual
55
Information
Regulatory
FCC Information | IC Compliance Notice | MPR II Compliance (Except SyncMaster 753v)
European Notice (Europe only) | PCT Notice
TCO'95-Ecological requirements for personal computers (TCO applied model only)
TCO'99-Ecological requirements for personal computers (TCO applied model only)
● FCC Information
User Instructions
The Federal Communications Commission Radio Frequency Interference Statement includes the following
warning:
Note:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television receptions, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
User Information
Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment. If necessary, consult your dealer or an experienced
radio/television technician for additional suggestions. You may find the booklet called How to Identify and
Resolve Radio/TV Interference Problems helpful. This booklet was prepared by the Federal
Communications Commission. It is available from the U.S. Government Printing Office, Washington,
DC 20402, Stock Number 004-000-00345-4.
Warning
User must use shielded signal interface cables to maintain FCC compliance for the product.
Declaration of conformity for products Marked with FCC Logo
This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesire$ operation.
The party responsible for product compliance:
SAMSUNG ELECTRONICS CO., LTD
America QA Lab of Samsung
85 West Tasman Drive
San Jose, CA 95134 USA
Tel) 408-544-5124
Fax) 408-544-5191
User’s Manual
56
Information
Provided with this monitor is a detachable power supply cord with IEC320 style terminations. It may be suitable for
connection to any UL Listed personal computer with similar configuration. Before making the connection, make
sure the voltage rating of the computer convenience outlet is the same as the monitor and that the ampere rating of
the computer convenience outlet is equal to or exceeds the monitor voltage rating.
For 120 Volt applications, use only UL Listed detachable power cord with NEMA configuration 5-15P type (parallel
blades) plug cap. For 240 Volt applications use only UL Listed Detachable power supply cord with NEMA
configuration 6-15P type (tandem blades) plug cap.
● IC Compliance Notice
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations of ICES-003.
Cet appareil Numérique de classe B respecte toutes les exigences du Règlemont ICES-003 sur les
équipements produisant des interférences au Canada.
● MPR II Compliance (Except SyncMaster 753v)
This monitor complies with SWEDAC(MPR II) recommendations for reduced electric and magnetic fields.
● European Notice (Europe only)
Products with the CE Marking comply with both the EMC Directive (89/336/EEC), (92/31/EEC), (93/68/EEC)
and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community.
Compliance with these directives implies conformity to the following European Norms:
• EN55022:1998 - Radio Frequency Interference
• EN55024:1998 - Electromagnetic Immunity
• EN61000-3-2:1995+A1+A2 - Power Line Harmonics
• EN61000-3-3:1995 - Voltage Fluctuations
• EN60950 - Product Safety.
● PCT Notice
User’s Manual
57
Information
● TCO'95-Ecological requirements for personal computers (TCO applied model only)
AB general requirements
AB2 Written Eco-document acompanying the products
Congratulations! You have just purchased a TCO'95 approved and labelled product! Your choice has provided you with a product
developed for professional use. Your purchase has also contributed to reducing the burden on the environment and to the further
development of environmentally- adapted electronic products.
Why do we have environmentally-labelled monitors?
In many countries, environmental labelling has become an established method for encouraging the adaptation of goods and services to
the environment.The main problem as far as monitors and other electronic equipment are concerned is that environmentally harmful
substances are used both in the products and during their manufacture. Since it has not been possible so far for the majority of
electronic equipment to be recycled in a satisfactory way, most of these potentially damaging substances sooner or later enter Nature.
There are also other characteristics of a monitor, such as energy consumption levels, that are important from both the working and
natural environment viewpoints.Since all types of conventional electricity generation have a negative effect on the environment (acidic
and climate-influencing emissions, radioactive waste, etc.) it is vital to conserve energy. Electronic equipment in offices consumes an
enormous amount of energy, since it is often routinely left running continuously.
What does labelling involve?
This product meets the requirements for the TCO'95 scheme, which provides for international environmental labelling of monitors.
The labelling scheme was developed as a joint effort by the TCO (The Swedish Confederation of Professional Employees),
Naturskyddsforeningen (The Swedish Society for Nature Conservation) and NUTEK (The National Board for Industrial and Technical
Development in Sweden).
The requirements cover a wide range of issues: environment, ergonomics, usability, emission of electrical and magnetic fields, energy
consumption and electrical and fire safety.
The environmental demands concern among other things restrictions on the presence and use of heavy metals, brominated and
chlorinated flame retardants, CFCs (freons), and chlorinated solvents. The product must be prepared for recycling and the manufacturer
is obliged to have an environmental plan, which must be adhered to in each country where the company conducts its operations policy.
The energy requirements include a demand that the monitor after a certain period of inactivity shall reduce its power consumption to a
lower level, in one or more stages. The length of time to reactivate the monitor shall be reasonable for the user.
Labelled products must meet strict environmental demands, for example in respect of the reduction of electric and magnetic fields,
along with physical and visual ergonomics and good usability.
TCO Development Unit 1996-11-29
On the page this folder you will find a brief summary of the environmental requirements met by this product.
The complere environmental criteria document may be ordered from:
TCO Development Unit
S-11494 Stockholm
Sweden
Fax: +46 8 782 92 07
E-mail (Internet): development@tco.se
Current information regarding TCO'95-approved and labelled products may also
be obtained via the Internet, using the address:
http://www.tco-info.com/
TCO'95 is a co-operative project between(3 logos)
User’s Manual
58
Information
Environmental Requirements
Brominated flame retardants are present in printed circuit boards, cables, wires, casings and housings. In turn, they delay the spread of
fire. Up to thirty percent of the plastic in a computer casing can consist of flame retardant substances. These are related to another
group of environmental toxins, PCBs, which are suspected to give rise to similar harm, including reproductive damage in fish eating
birds and mammals, due to the bioaccumulative processes. Flame retardants have been found in human blood and researchers fear
that disturbances in foetus development may occur.
● TCO'95 demand requires that plastic components weighing more than 25 grams must not contain organically bound chlorine and
bromine.
Lead
Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous system and in higher doses,
causes lead poisoning.
● TCO'95 requirement Permits the inclusion of lead since no replacement has yet been developed.
Cadmium
Cadmium is present in rechargeable batteries and in the colour generating layers of certain computer displays. Cadmium damages the
nervous system and is toxic in high doses.
● TCO'95 requirement states that batteries may not contain more than 25 ppm (parts per million) of cadmium.
The colour-generating layers of display screens must not contain any cadmium.
Mercury
Mercury is sometimes found in batteries, relays and switches. Mercury damages the nervous system and is toxic in high doses.
● TCO'95 requirement states that batteries may not contain more than 25 ppm (parts per million) of mercury.
It also demands that no mercury is present in any of the electrical or electronics components concerned with the display unit.
CFCs (freons)
CFCs (freons) are sometimes used for washing printed circuit boards and in the manufacturing of expanded foam for packaging. CFCs
break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on Earth of ultraviolet light
with consequent increased risks of skin cancer (malignant melanoma).
● The relevant TCO'95 requirement: Neither CFCs nor HCFCs may be used during the manufacturing of the product or its packaging.
● TCO'99-Ecological requirements for personal computers (TCO applied model only)
Congratulations!
You have just purchased a TCO'99 approved and labelled product! Your choice has provided you with a product developed for
professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of
environmentally adapted electronics products.
This product meets the requirements for the TCO'99 scheme which provides for an international environmental and quality labelling
labelling of personal computers. The labelling scheme was developed as a joint effort by the TCO(The Swedish Confederation of
Professional Employees), Svenska Naturskyddsforeningen(The Swedish Society for Nature Conservation), Statens
Energimyndighet(The Swedish National Energy Administration) and SEMKO AB.
User’s Manual
59
Information
The requirements cover a wide range of issuse: environment, ergonomics, usability, reduction of electric and magnetic fields, energy
consumption and electrical safet
Why do we have environmentally labelled computers?
In many countries, environmental labelling has become an established method for encouraging the adaptation of goods and services to
the environment. The main problem, as far as computers and other electronics equipment are concerned, is that environmentally
harmful substances are used both in the products and during their manufacture. Since it is not so far possible to satisfactorily recycle
the majority of electronics equipment, most of these potentially damaging substances sooner or later enter nature.
There are also other characteristics of a computer, such as energy consumption levels, that are important from the viewpoints of both
the work (internal) and natural (external) environments. Since all methods of electricity generation have a negative effect on the
environment (e.g. acidic and climate-influencing emissions, radioactive waste), it is vital to save energy. Electronics equipment in offices
is often left running continuously and thereby consumes a lot of energy.
What does labelling involve?
The environmental demands has been developed by Svenska Naturskyddsforeningen (The Swedish Society for Nature Conservation).
These demands impose restrictions on the presence and use of heavy metals, brominated and chlorinated flame retardants,
CFCs(freons)and chlorinated solvents, among other things. The product must be prepared for recycling and the manufacturer is obliged
to have an environmental policy which must be adhered to in each country where the company implements its operational policy.
The energy requirements include a demand that the computer and/or display, after a certain period of inactivity, shall reduce its power
consumption to a lower level in one or more stages. The length of time to reactivate the computer shall be reasonable for the user.
Below you will find a brief summary of the environmental requirements met by this product. The complete environmental criteria
document may be ordered from:
TCO Development
SE-114 94 Stockholm, Sweden
Fax: +46 8 782 92 07
Email (Internet): development@tco.se
Current information regarding TCO'99 approved and labelled products may also be obtained via the Internet, using the address:
http://www.tco-info.com/
Environmental requirements
Flame retardants
Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to
delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances. Most flame retardants
contain bromine or chloride, and those flame retardants are chemically related to another group of environmental toxins, PCBs. Both
the flame retardants containing bromine or chloride and the PCBs are suspected of giving rise to severe health effects, including
reproductive damage in fish-eating birds and mammals, due to the bio-accumulative* processes. Flame retardants have been found in
human blood and researchers fear that disturbances in foetus development may occur.
The relevant TCO'99 demand requires that plastic components weighing more than 25 grams must not contain flame retardants with
organically bound bromine or chlorine. Flame retardants are allowed in the printed circuit boards since no substitutes are available.
Cadmium**
Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer displays. Cadmium damages the
nervous system and is toxic in high doses. The relevant TCO'99 requirement states that batteries, the colour-generating layers of
display screens and the electrical or electronics components must not contain any cadmium.
Mercury**
Mercury is sometimes found in batteries, relays and switches. It damages the nervous system and is toxic in high doses. The relevant
TCO'99 requirement states that batteries may not contain any mercury. It also demands that mercury is not present in any of the
electrical or electronics components associated with the labelled unit. There is however one exception. Mercury is, for the time being,
permitted in the back light system of flat panel monitors as today there is no commercially available alternative. TCO aims on removing
this exception when a Mercury free alternative is available.
User’s Manual
60
Information
CFCs (freons)
The relevant TCO'99 requirement states that neither CFCs nor HCFCs may be used during the manufacture and assembly of the
product. CFCs (freons) are sometimes used for washing printed circuit boards. CFCs break down ozone and thereby damage the
ozone layer in the stratosphere, causing increased reception on earth of ultraviolet light with e.g. increased risks of skin cancer
(malignant melanoma) as a consequence.
Lead**
Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous system and in higher doses,
causes lead poisoning. The relevant TCO'99 requirement permits the inclusion of lead since no replacement has yet been developed.
* Bio-accumulative is defined as substances which accumulate within living organisms.
** Lead, Cadmium and Mercury are heavy metals which are Bio-accumulative.
User’s Manual
61
Information
Authority
Information in this document is subject to change without notice.
© 2001 Samsung Electronics Co., Ltd. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden.
Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection
with the furnishing, performance, or use of this material.
Samsung is the registered trademark of Samsung Electronics Co., Ltd.;
Microfoft, Windows and Windows NT are registered trademark of Microsoft Corporation; VESA, DPMS and DDC are registered
trademarks of Video Electronics Standard Association;
the ENERGY STAR name and logo are registered trademarks of the U.S. Environmental Protection Agency(EPA).
As an ENERGY STAR Partner, Samsung Electronics Co., Ltd. has determined that this product meets the ENERGY STAR
guidelines for energy efficiency.
All other product names mentioned herein may be the tradmarks or registered trademarks of their respective owners.
Installing the Video Driver
http://www.samsung-monitor.com
http://www.samsungmonitor.com(USA only)
Download PDF

advertising