Samsung | DVD-VR330S | Samsung DVD-VR330S 사용자 매뉴얼

00995J(00)_VR330_AFS-Eng1
2006.4.13
7:0 PM
Page 1
Instruction Manual
DVD-VR330,VR330S
www.samsung.com
English
AK68-00995J-00
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:0 PM
Page 2
Getting Started
Warning
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE THE COVER(OR BACK).
NO USER-SERVICEABLE PARTS ARE INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol indicates “dangerous voltage”
inside the product that presents a risk of
electric shock or personal injury.
This symbol indicates important instructions
accompanying the product.
Do not install this equipment in a confined space such
as a bookcase or similar unit.
WARNING : To prevent damage which may result in fire or
electric shock hazard, do not expose this appliance to rain or moisture.
CAUTION : This DVD Recorder & VCR USES AN INVISIBLE LASER BEAM WHICH CAN CAUSE
HAZARDOUS RADIATION EXPOSURE IF
DIRECTED.
BE SURE TO OPERATE RECORDER CORRECTLY AS INSTRUCTED.
CAUTION
THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR
YOURSELF. REFER SERVICING TO QUALIFIED
PERSONNEL.
CAUTIONS
Caution: To prevent electric shock, match wide blade of
plug to wide slot, fully insert.
Attention: Pour éviter les chocs électriques, introduíre la
lame la plus large de la fiche dans la borne
correspondante de la prise et pousser jusqu au
fond.
This product satisfies FCC regulations when shielded
cables and connectors are used to connect the unit to
other equipment. To prevent electromagnetic interference
with electric appliances, such as radios and televisions, use
shielded cables and connectors for connections.
FCC NOTE (for U.S.A):
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
2 - English
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or
television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: FCC regulations state that any unauthorized
changes or modifications to this equipment
may void the user’s authority to operate it.
This unit can be used only where the power
supply is ~100-240V, 60Hz. It cannot be used
Note
elsewhere.
This DVD Recorder & VCR is designed and
manufactured to respond to the Region
Management Information.
If the Region number of a DVD disc does not
correspond to the Region number of this, the
DVD Recorder & VCR cannot play the disc.
This device is protected by U.S. Patent
Nos.4,631,603;4,577,216;4,819,098;4,907,093;
and 6,516,132. This product incorporates copyright protection technology that is protected by
U.S. patents and other intellectual property rights.
Use of this copyright protection technology must
be authorized by Macrovision,and is intended for
home and other limited viewing uses only unless
otherwise authorized by Macrovision. Reverse
engineering or disassembly is prohibited.
This product is covered by one or more of the
following U.S. patents:
5,034,830 5,060,200 5,457,669 5,561,649
5,691,858 5,705,762 5,987,417 6,043,912
6,222,983 6,272,096 6,377,524 6,377,531
6,385,587 6,389,569 6,389,570 6,408,408
6,466,532 6,473,736 6,477,501 6,480,829
6,556,520 6,556,521 6,556,522 6,594,208
6,674,697 6,674,957 6,721,493 6,728,474
6,741,535 09/610381 09/610695
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:0 PM
Page 3
Precaution
• Exterior interference such as lightning and static electricity can affect normal operation of this recorder. If
this occurs, turn the DVD Recorder & VCR off and on
again with the POWER button, or disconnect and then
reconnect the AC power cord to the AC power outlet.
The recorder will operate normally.
use.
Important Safety Instructions
Read these operating instructions carefully before using
the unit. Follow all the safety instructions listed below.
Keep these operating instructions handy for future reference.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings, Install in
accordance with the manufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized
or grounding- type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. if the provided plug does not
fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles, and the point where they exit from the
apparatus.
11) Only use attachments/accessories specified by
the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or
when unused for long periods of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate normally, or has been
dropped.
Handling Cautions
• Before connecting other components to this
recorder, be sure to turn them all off.
• Do not move the recorder while a disc is being
played, or the disc may be scratched or broken,
and the recorder’s internal parts may be damaged.
• Do not put a flower vase filled with water or any
small metal objects on the recorder.
• Be careful not to put your hand into the disc tray.
• Do not place anything other than the disc in the
disc tray.
• Disconnect the AC power cord from the AC outlet
when you don’t intend to use the recorder for long
periods of time.
• Clean the disc by wiping in a straight line from the
inside to the outside of the disc.
Maintenance of Cabinet
For safety reasons, be sure to disconnect the AC power
cord from the AC outlet.
• Do not use benzene, thinner, or other solvents for
cleaning.
• Wipe the cabinet with a soft cloth.
Disc Handling
• Use discs with regular shapes.
If an irregular disc (a disc with
a special shape) is used, this
DVD Recorder & VCR may be
damaged.
Holding discs
• Avoid touching the surface of a disc
where recording is performed.
DVD-RAM, DVD±RW and DVD±R
• Clean with an optional DVD-RAM/PD
disc cleaner.
Do not use cleaners or cloths for CDs
to clean DVD-RAM/DVD±RW/DVD±R
discs.
DVD-Video, CD
• Wipe off dirt or contamination on the disc with a soft
cloth.
Cautions on handling discs
• Do not write on the printed side with a ball-point pen
or pencil.
• Do not use record cleaning sprays or antistatic. Also,
do not use volatile chemicals, such as benzene or
thinner.
• Do not apply labels or stickers to discs. (Do not use
discs fixed with exposed tape adhesive or leftover
peeled-off stickers.)
English - 3
Getting Started
• Be sure to remove the disc and turn off the recorder after
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:0 PM
Page 4
• Do not use scratch-proof protectors or covers.
• Do not use discs printed with label printers available
on the market.
Getting Started
• Do not load warped or cracked discs.
Disc Storage
Be careful not to harm the disc because the data on
these discs is highly vulnerable to the environment.
• Do not keep under direct sunlight.
• Keep in a cool ventilated area.
• Store vertically.
• Keep in a clean protection jacket.
• If you move your DVD Recorder & VCR suddenly from
a cold place to a warm place, condensation may generate on the operating parts and lens and cause
abnormal disc playback. In this case, do not connect
the plug to the power outlet and wait for two hours.
Then insert the disc and try to play back again. It will
work properly when condensation has evaporated.
Disc Specifications
DVD-Video
• A digital versatile disc (DVD) can contain up to 135minutes of images, 8 audio languages and 32 subtitle
languages. It is equipped with MPEG-2 picture compression and Dolby 3D surround, allowing you to
enjoy vivid and clear theater quality images in the
comfort of your own home.
• When switching from the first layer to the second layer
of a double-layered DVD Video disc, there may be
momentary distortion in the image and sound.
This is not a malfunction of the unit.
• Once a DVD±R/DVD-RW(V) recorded is finalized, it is
playable in a standard DVD player.
Audio CD
• An audio disc on which 44.1kHz PCM Audio is recorded.
• Plays CD-DA format audio CD-R and CD-RW discs. This
unit may not be able to play some CD-R or CD-RW discs
due to the condition of the recording.
CD-R/-RW
MP3 CD-R/-RW
• Only CD-R discs with MP3 files recorded with
ISO9660 or JOLIET format can be played back
• Only MP3 files with the "mp3" or "MP3" extension can
be used.
JPEG CD-R/-RW
• Only JPEG files with the ".jpg", ".JPG" extension can be
used.
• The unit can handle a maximum of 1000 files and folders.
• Maximum size of progressive JPEG is 3M pixels.
• MOTION JPEG is not supported.
• DVD-RAM/±RW/±R discs that contain JPEG files can be
played back.
Using CD-R/-RW
• Use a 700MB(80 minutes) CD-R/-RW disc.
If possible, do not use a 800MB(90 minutes) or above
disc, as the disc may not play back.
• If the CD-R/-RW disc was not recorded as a closed session, you may experience a delay in the early play-back
time, and all recorded files may not play.
• Some CD-R/-RW discs may not be playable with this unit,
depending on the device which was used to burn them.
For contents recorded on CD-R/-RW media from CDs for
your personal use, playability may vary depending on contents and discs.
DVD±R Disc Playback and Recording
• Once a DVD±R recorded is finalized, it is playable in a
standard DVD player.
• You can record onto the available space on the disc and
perform editing functions such as giving titles to discs and
programs and erasing programs before finalizing.
• When programming is erased from a DVD±R, that space
does not become available. Once an area on a DVD±R is
recorded on, that area is no longer available for recording,
whether the recording is erased or not.
• It takes about 30 seconds for the unit to complete recording management information after recording finishes.
• This product optimizes the DVD±R for each recording.
Optimizing is carried out when you start recording after
inserting the disc or turning on the unit. Recording onto
the disc may become impossible if optimizing is carried
out too many times.
• Playback may be impossible in some cases due to the
condition of recording.
• This unit can play back DVD±R discs recorded and finalized with a Samsung DVD video recorder. It may not be
able to play some DVD±R discs depending on the disc
and the condition of the recording.
DVD-RW Disc Playback and Recording
• For MP3 files recorded with a VBR(Variable Bit
Rates), from 80 Kbps to 320 Kbps, the sound may cut
in out.
• Playable bitrate range is from 56Kbps to 320Kbps.
• The unit can handle a maximum of 1000 files and folders.
• DVD-RAM/±RW/±R discs that contain MP3 files can
be played back.
4 - English
• Recording and playback can be performed on DVDRW discs in both Video and VR Modes.
• Once a DVD-RW recorded in VR Mode or Video mode
is finalized, you cannot perform additional recording.
• Once a DVD-RW recorded in Video Mode is finalized,
it becomes DVD-Video.
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:0 PM
Page 5
• In both modes, playback can be performed before and after
• DVD-RW (VR mode)
- This is a format that is used for recording data on
DVD-RW disc. You can record multiple titles, edit, delete,
partial delete, create a playlist, etc.
- A disc that is recorded in this mode may not be played
by existing DVD players.
• DVD-RW (Video mode)
- This is a format that is used for recording data on a
DVD-RW or DVD-R disc. The disc can be played by an
existing DVD player once it has been finalized.
- If a disc that has been recorded in Video mode by a different manufacturer's recorder but has not been finalized
it cannot be played or additionally be recorded by this
recorder.
DVD+RW Disc Playback and Recording
• With DVD+RW discs, there is no difference between
DVD-Video format (Video mode) and DVD-Video
Recording format (VR mode).
• You can make your own chapters on DVD+RWs and edit
them using the Chapter Edit menu.
• Finalizing is generally unnecessary when using a
DVD+RW disc.
DVD-RAM Disc Playback and Recording
• For cartridge type DVD-RAM discs, remove the
cartridge and use the disc only.
• Ensure that the recording mode is set to VR mode.
Otherwise, this product will not be able to play the
recording.
• You cannot play a DVD-RAM in most DVD players due
to compatibility issues.
• Only DVD-RAM standard Version 2.0 discs can be
played in this unit.
• DVD-RAM recorded on this unit may not work with other
DVD Players. To determine compatibility with these DVDRAM discs, refer to the user’s manual for the player.
COPY PROTECTION
• Many DVD discs are encoded with copy protection. Because of this, you should only connect
your DVD Recorder & VCR directly to your TV,
not to a VCR. Connecting to a VCR results in a
distorted picture from copy-protected DVD discs.
• This product incorporates copyright protection
technology that is protected by methods claims of
certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and
other rights owners. Use of this copyright protection technology must be authorized by
Macrovision Corporation, and is intended for
home and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.
Protection
• Program-protection: See page 73 “Locking a Title”
• Disc-protection: See page 86 “Disc Protection”
❋ DVD-RAM/DVD±RW/DVD±R discs that are incompatible with the DVD-VIDEO format cannot be played with
this product.
❋ For more information on DVD recording compatibility,
consult your DVD-RAM/DVD±RW/DVD±R manufacturer.
❋ Use of poor quality DVD-RAM/DVD±RW/DVD±R discs
may cause following unexpected problems including,
without limitation, recording failure, loss of recorded or
edited materials or damage to the recorder.
Do not use the following discs!
• LD, CD-G, CD-I, CD-ROM and DVD-ROM discs should
not be used in this product.
[Note]
• Some commercial discs and DVD discs purchased outside your region may not be playable with this product.
When these discs are played, either “No Disc” or “The
disc cannot be played. Please check the regional code
of the disc.” will be displayed.
• If your DVD-RAM/DVD±RW/DVD±R disc is an illegal
copy or is not in DVD video format, it may also not be
playable.
Disc compatibility
• A 8X speed DVD+RW or above disc can be played, but
can not be recorded.
• Not all brands of discs will be compatible with this unit.
• The latest firmware upgrade to improve recording &
playback quality can be downloaded from our web site.
(Download Center at www.samsung.com)
• If disc compatibility problems continue, or there is an
issue upgrading your recorder, contact the Call Center at
1-800-SAMSUNG.
English - 5
Getting Started
finalization, but additional recording, deleting and editing can
not be performed after finalization.
• If you want to record the disc in VR Mode and then record in
V Mode, be sure to execute format. Be careful when executing Format because all the recorded data may be lost.
• For an unused disc, a message that asks whether to initialize
a disc or not. If you select “Yes”, disc will be formatted in VR
mode.
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:0 PM
Page 6
Contents
Step 3 : Connecting the Audio Cable . . . . . . . . . . .22
Connecting to your TV . . . . . . . . . . . . . . . . . . . . . . . .22
Connecting to a stereo amplifier with
Getting Started
analog input jacks . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Connecting to an AV amplifier with a
digital input jack
Getting Started
Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Precaution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . .3
Handling Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Maintenance of Cabinet . . . . . . . . . . . . . . . . . . . . . . . . . .3
Disc Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Disc Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Disc Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
General Features . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Before Reading the User’s Manual . . . . . . . . . . . . .8
How to use the DVD Recorder & VCR . . . . . . . . . . .9
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Front Panel (DVD-VR330) . . . . . . . . . . . . . . . . . . . . . . .11
Rear Panel (DVD-VR330) . . . . . . . . . . . . . . . . . . . . . . .11
Front Panel (DVD-VR330S) . . . . . . . . . . . . . . . . . . . . . .12
Rear Panel (DVD-VR330S) . . . . . . . . . . . . . . . . . . . . . .12
Front Panel Display . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Tour of the Remote Control . . . . . . . . . . . . . . . . . . . . . .14
Connecting & Setting Up
Quick Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Step 1 : Connecting the Antenna Cable . . . . . . . . . .16
Antenna + DVD Recorder & VCR + TV :
. . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Step 4 : Connecting External Devices . . . . . . . . . .25
Connecting a VCR, Set-Top Box(STB) or
DVD player to the AV 1 IN or S-VIDEO IN jacks . . . . .25
Connecting a Camcorder to the AV 2 IN jacks . . . . . .26
Connecting a Camcorder to the DV IN jack . . . . . . . .27
Step 5 : Connecting the Power Cord . . . . . . . . . . .28
Step 6 : Preparing the Remote Control . . . . . . . . .28
Setting the Remote Control . . . . . . . . . . . . . . . . . . . . .29
System Setup
On-Screen Menu Navigation . . . . . . . . . . . . . . . . .30
Auto Clock Set . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Manual Clock Set . . . . . . . . . . . . . . . . . . . . . . . . .32
Channel Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Auto Channel Memory . . . . . . . . . . . . . . . . . . . . . .33
Channel Add/Delete . . . . . . . . . . . . . . . . . . . . . . .34
RF Output Channel . . . . . . . . . . . . . . . . . . . . . . . .34
Setting Up the Language Options . . . . . . . . . . . . .35
Setting Up the Audio Options . . . . . . . . . . . . . . . .36
Setting Up the Display(Video) Options . . . . . . . . . .37
Setting Up the Parental Control . . . . . . . . . . . . . . .38
VCR Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Video Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
DVD EP Mode Time . . . . . . . . . . . . . . . . . . . . . . .41
Automatic Chapter Creator . . . . . . . . . . . . . . . . . .41
Quick Recording . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Playback
No Cable box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Antenna + Cable box + DVD Recorder & VCR + TV :
Cable box with many scrambled channels . . . . . . . . . . .17
Antenna + DVD Recorder & VCR + Cable box + TV :
Cable box with a few scrambled channels . . . . . . . . . . .18
Step 2 : Connecting the Video Cable . . . . . . . . . . . .19
Connecting to a Video input jack . . . . . . . . . . . . . . . . . .19
Connecting to an S-video input jack . . . . . . . . . . . . . . . .20
Connecting to Component video input jacks (Y,PB,PR) . .21
6 - English
DVD Playback
Before Playing . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Using the Disc Menu and Title Menu . . . . . . . . . . .45
Using the Search & Skip Functions . . . . . . . . . . . .45
Slow Motion Play / Step Motion Play . . . . . . . . . . .46
About ANYKEY . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Repeat Playback . . . . . . . . . . . . . . . . . . . . . . . . . .47
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:0 PM
Page 7
VCR Playback
Playing the VCR . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Tracking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Special VCR Playback Features . . . . . . . . . . . . . .57
S-VHS Playback . . . . . . . . . . . . . . . . . . . . . . . . . .57
Variable Search System . . . . . . . . . . . . . . . . . . . . .57
Recording
DVD Recording
Before Recording . . . . . . . . . . . . . . . . . . . . . . . . .59
Recordable discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Recording Formats . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Recording Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Unrecordable video . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Recording the Current Channel you are watching . .61
Recording from External Devices . . . . . . . . . . . . . .62
Recording through a DV Input jack . . . . . . . . . . . .62
Making a One Touch Recording(OTR) . . . . . . . . . .63
Making a Timer Recording . . . . . . . . . . . . . . . . . . .63
Editing the Scheduled Record List . . . . . . . . . . . . .65
Deleting the Scheduled Record List . . . . . . . . . . . .65
VCR Recording
Basic VCR Recording . . . . . . . . . . . . . . . . . . . . . .66
Check Remaining Time . . . . . . . . . . . . . . . . . . . . .67
Special Recording Features . . . . . . . . . . . . . . . . .67
Copy to DVD or VCR . . . . . . . . . . . . . . . . . . . . . . .68
Editing
Playing the Title List . . . . . . . . . . . . . . . . . . . . . . . .70
Basic Editing (Title List) . . . . . . . . . . . . . . . . . . . . .72
Renaming(Labeling) a Title . . . . . . . . . . . . . . . . . . . . .72
Locking(Protecting) a Title . . . . . . . . . . . . . . . . . . . . . .73
Deleting a Title . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
Deleting a Section of a Title . . . . . . . . . . . . . . . . . . . .74
Editing a Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
Dividing a Title . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Advanced Editing (Playlist) . . . . . . . . . . . . . . . . . . .79
Creating a Playlist . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Playing Titles in the Playlist . . . . . . . . . . . . . . . . . . . . .80
Renaming a Playlist Title . . . . . . . . . . . . . . . . . . . . . . .80
Editing a Scene for the Playlist . . . . . . . . . . . . . . . . . .81
Copying a Playlist Title to the VCR . . . . . . . . . . . . . . .84
Deleting a Playlist Title from the Playlist . . . . . . . . . . .85
Disc Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
Editing the Disc Name . . . . . . . . . . . . . . . . . . . . . .85
Disc Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
Formatting a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
Finalizing a disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
Unfinalizing a disc (V/VR mode) . . . . . . . . . . . . . . . . .88
Delete All Title Lists . . . . . . . . . . . . . . . . . . . . . . . . . . .89
Edit Compatible . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90
Reference
Troubleshooting
(DVD-VIDEO/DVD-RAM/DVD±RW/DVD±R) . . . . .92
Troubleshooting (DVD) . . . . . . . . . . . . . . . . . . . . . .93
Troubleshooting (VCR) . . . . . . . . . . . . . . . . . . . . .94
Problems and Solutions (Display error message) . .95
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . .97
English - 7
Getting Started
Selecting the Subtitle & Audio Language . . . . . . . .48
Changing the Camera Angle . . . . . . . . . . . . . . . . .49
Zooming-In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Using the Bookmarks . . . . . . . . . . . . . . . . . . . . . .50
Using the Markers . . . . . . . . . . . . . . . . . . . . . . . . .51
Playing back an Audio CD (CD-DA) . . . . . . . . . . . .52
Playing back an MP3 Disc . . . . . . . . . . . . . . . . . . .53
Repeat Playback of an Audio/MP3 Disc . . . . . . . .54
Play Option Mode . . . . . . . . . . . . . . . . . . . . . . . . .54
To Program Tracks . . . . . . . . . . . . . . . . . . . . . . . . .55
Playing a Picture Disc . . . . . . . . . . . . . . . . . . . . . .55
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:0 PM
Page 8
Getting Started
General Features
The DVD-VR330, VR330S allows you to record and play
high quality digital video on DVD-RAM/DVD±RW/DVD±R
discs. You can record and edit digital video on DVD-RAM/
DVD±RW/ DVD±R discs as if they were VCR tapes.
High quality digital audio and video recording and
playback
You can record up to approximately 16-hours of video on a
double side 9.4 GB DVD-RAM disc,up to 15-hours on a
dual-layer 8.5GB DVD±R disc, and up to 8-hours on a 4.7
GB DVD-RAM/DVD±RW/DVD±R disc, depending on the
recording mode.
Before Reading the
User’s Manual
Make sure to check the following terms before reading
the user’s manual.
Icons that will be used in manual
Term
Definition
DVD
This involves a function available
in DVD or DVD-R/DVD-RW(V)/+R
discs that have been recorded
and finalized.
Creating DVD video titles using DVD±RW/DVD±R discs
With the DVD-VR330, VR330S, you can create your own
DVD video titles on 4.7 GB DVD±RW/DVD±R or 8.5GB
DVD±R discs.
RAM
This involves a function available
in DVD-RAM.
-RW
This involves a function available
in DVD-RW.
A Variety of Recording Options
Select an appropriate recording mode between XP, SP, LP
and EP to meet your recording needs. (See page 60.)
• XP mode - High quality, about 1 hour
• SP mode - Standard quality, about 2 hours
• LP mode - Low quality, about 4 hours
• EP mode - Lower quality, about 6 or 8 hours
- The dual layer DVD±Rs have approximately double the
capacity of single layer DVD±Rs. (See page 43.)
-R
This involves a function available
in DVD-R.
+RW
This involves a function available
in DVD+RW.
+R
This involves a function available
in DVD+R.
CD
This involves a function available
in a data CD (CD-R or CD-RW).
JPEG
This involves a function available
in CD-R/-RW or DVD±R/±RW/
-RAM discs.
MP3
This involves a function available
in CD-R/-RW or DVD±R/±RW/
-RAM discs.
Copying digital camcorder content using DV input jack
Record digital camcorder images onto DVD-RAM/DVD±
RW/DVD±R discs or video tape using the DV input jack
(IEEE 1394-4pin). (See page 62.)
High quality progressive scan
Progressive scanning provides high resolution and flicker
free video. The 10-bit 54-MHz DAC, 2D Y/C Separating circuitry and Time Base Corrector processor technology provide you with the highest image playback and recording
quality. (See page 21.)
Component progressive scan output video is available in
both DVD and VCR modes.
A variety of functions with easy-to-use user interface
Integrated menu system and messaging functionality allow
you to perform the desired operations easily and conveniently. With a DVD-RAM/DVD-RW(VR mode) disc, you
can edit recorded images, create playlist, and edit video in
specific sequence according to your needs.
Copyright
©2006 Samsung Electronics Co.
All rights reserved; No part or whole of this user’s
manual may be reproduced or copied without the prior
written permission of Samsung Electronics Co.
8 - English
Icon
Caution
NOTE
This involves a case where a
function does not operate or
settings may be cancelled.
This involves tips or instructions
on the page that help each
function operate.
One-Touch A function that can be operated
button
by using only one button.
ANYKEY
button
A function that can be operated
by using ANYKEY button.
About the use of this user’s manual
1) Be sure to be familiar with Safety Instructions before
using this product. (See pages 2~5)
2) If a problem occurs, check the Troubleshooting.
(See pages 92~94)
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:0 PM
Page 9
How to use the DVD
Recorder & VCR
Select the disc type
This unit can record on the following types of discs.
If you want to repeatedly record on the same disc or
you want to edit the disc after recording, select a
rewritable DVD±RW or DVD-RAM type disc. If you
want to save a recording without any changes,
choose a non-rewritable DVD±R.
Step 2
Format the disc to start recording
Unlike a VCR, the recorder automatically starts formatting when an unused disc is inserted. This is required
for the preparation of recording on a disc.
Recording
There are two different recording methods: Direct
Recording and Timer Recording. Timer recording is
classified as a Date : Once, Daily or Weekly.
Recording mode : XP (high quality mode), SP (standard quality mode), LP (long recording mode), and
EP (extended mode).
Step 4
Playing
You can select the title you want to play in a displayed
menu and then immediately start playback.
A DVD consists of sections called titles, and sub sections called chapters.
During recording, a title is created between two points
where you start and stop recording. Chapters will be
created automatically when you finalize recording on
DVD-R / DVD-RW discs in Video mode.
You can make your own chapters on DVD+RWs and
edit them using the Chapter Edit menu.
The chapter’s length (interval between chapters) varies
according to the recording mode.
Using a DVD-RAM
This type of disc can be formatted in DVD-Video
Recording format (VR mode). You can edit recorded
images and create a playlist in a specific sequence
according to your requirements.
Using a DVD±RW/+R
• When an unused DVD±RW/+R disc is first inserted,
Step 5
the message "Uninitialized Disc. Do you want to initialize this disc?" will be displayed.
If you select Yes, initializing will be start. DVD-RW
disc can be formatted in either DVD-Video format
(Video mode) or DVD-Video Recording format (VR
mode)
• With DVD+RW discs, there is no difference between
DVD-Video format (Video mode) and DVD-Video
Recording format (VR mode).
Editing on discs is easier than conventional video
tapes. The recorder supports many different edit functions, possible only with DVDs.
With a simple and easy edit menu, you can operate
various edit functions, such as delete, copy, rename,
lock, etc., on a recorded title.
Using a DVD-R
Initializing disc is unnecessary and only V mode
Recording is supported. You can play this type of disc
on various DVD components only when they have
been finalized.
■
Note
■
Editing a recorded disc
Creating a playlist (DVD-RAM/-RW in VR mode)
With this recorder, you can create a new playlist on
the same disc and edit it without changing the
original recording.
You can only use either the VR or Video
mode on a DVD-RW, but not both at the
same time.
You can format a DVD-RW to V or VR
mode using disc manager.
It should be noted that the disc's data will
be lost when changing formats.
English - 9
Getting Started
Step 1
Step 3
00995J(00)_VR330_AFS-Eng1
Getting Started
Step 6
2006.4.13
7:0 PM
Page 10
Finalizing & Playing on
other DVD components
To play your DVD on other DVD players, finalizing
may be necessary. First, finish all editing and recording operations, then finalize the disc.
When using a DVD-RW disc in VR Mode
Although finalizing is generally unnecessary when
playing the disc on a VR Mode compatible component, a finalized disc should be used for playback.
When using a DVD-RW disc in Video Mode
The disc should be finalized first to enable playback
on anything other than this recorder. No more editing
or recording can be made on the disc once it has
been finalized.
When using a DVD±R disc
You should finalize the disc to play it on a component
other than this recorder. You cannot edit or record on
the disc once it has been finalized.
10 - English
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:0 PM
Page 11
Description
Getting Started
Front Panel (DVD-VR330)
1
5
1.
2.
3.
4.
5.
6.
7.
8.
6
7
2
8
9
DVD DECK
DVD OPEN/CLOSE BUTTON
VCR DECK
VCR EJECT BUTTON
POWER BUTTON
VIDEO INPUT JACK (AV 2 IN)
AUDIO L, R INPUT JACKS (AV 2 IN)
DV INPUT JACK
4
3
10
11
9.
10.
11.
12.
13.
14.
15.
12
13
14
15
P.SCAN BUTTON
FRONT PANEL DISPLAY
DVD/VCR SELECT BUTTON
COPY BUTTON
CHANNEL / BUTTONS
RECORD BUTTON
PLAY/STILL, REW/SKIP, F.F/SKIP, STOP
BUTTONS
Rear Panel (DVD-VR330)
1
4 5 6
2
7
8
3
9 10
11
Fan
The fan always revolves when the power is on.
Ensure a minimum of 4” clear space on all sides of the fan
when installing the product.
1.
2.
3.
4.
5.
VIDEO INPUT JACK (AV 1 IN)
VIDEO OUT JACK (AV OUT)
AUDIO OUT JACKS
(COMPONENT OUT)
S-VIDEO IN/OUT JACKS
ANT IN JACK
6.
7.
8.
9.
10.
11.
ANT OUT (TO TV) JACK
AUDIO INPUT JACKS (AV 1 IN)
AUDIO OUT JACKS (AV OUT)
DIGITAL AUDIO OUT JACK (OPTICAL)
DIGITAL AUDIO OUT JACK (COAXIAL)
VIDEO OUT JACKS (COMPONENT OUT)
English - 11
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:0 PM
Page 12
Front Panel (DVD-VR330S)
2
4
3
Getting Started
1
5
1.
2.
3.
4.
5.
6.
7.
8.
6
7
8
9
DVD DECK
DVD OPEN/CLOSE BUTTON
VCR DECK
VCR EJECT BUTTON
POWER BUTTON
VIDEO INPUT JACK (AV 2 IN)
AUDIO L, R INPUT JACKS (AV 2 IN)
DV INPUT JACK
10
11
9.
10.
11.
12.
13.
14.
15.
12
13
14
15
P.SCAN BUTTON
FRONT PANEL DISPLAY
DVD/VCR SELECT BUTTON
COPY BUTTON
CHANNEL / BUTTONS
RECORD BUTTON
PLAY/STILL, REW/SKIP, F.F/SKIP, STOP
BUTTONS
Rear Panel (DVD-VR330S)
1
4 5 6
2
7
8
3
9 10
11
Fan
The fan always revolves when the power is on.
Ensure a minimum of 4” clear space on all sides of the fan
when installing the product.
1.
2.
3.
4.
5.
VIDEO INPUT JACK (AV 1 IN)
VIDEO OUT JACK (AV OUT)
AUDIO OUT JACKS
(COMPONENT OUT)
S-VIDEO IN/OUT JACKS
ANT IN JACK
12 - English
6.
7.
8.
9.
10.
11.
ANT OUT (TO TV) JACK
AUDIO INPUT JACKS (AV 1 IN)
AUDIO OUT JACKS (AV OUT)
DIGITAL AUDIO OUT JACK (OPTICAL)
DIGITAL AUDIO OUT JACK (COAXIAL)
VIDEO OUT JACKS (COMPONENT OUT)
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:0 PM
Page 13
Front Panel Display
1
2
3
4
5
6
Getting Started
7
1.
2.
3.
4.
5.
6.
DVD is activated.
DVD-RAM is activated.
DVD(±)R or DVD(±)RW is actived.
Progressive Scan mode is activated.
Record function is activated.
VCR is activated.
8
9
10
7. DVD or CD media is loaded.
8. The time, counter position or current deck
status is indicated.
9. When you set a Timer recording,
this indicator appears.
10. VHS videotape is loaded.
Unpacking
Accessories
Check for the supplied accessories below.
Audio/Video Cable
RF Cable for TV
EP-2 Plug Converter
Remote Control
Batteries for Remote
Control (AAA Size)
User’s Manual
Quick Guide
English - 13
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:0 PM
Page 14
Getting Started
Tour of the Remote Control
1
2
18
19
20
3
21
4
5
6
7
22
23
8
24
9
25
26
10
11
12
13
14
15
16
17
27
28
29
30
31
32
33
1. DVD Button
Press this when you use a DVD.
2. TV Button
Press this to operate TV.
3. POWER Button
4. NUMBER Button
5. 100+ Button
Press this to select channel 100 or higher.
6. F.ADV/SKIP Button
7. Playback-related Buttons
Forward/Rewind, Search, Skip, Stop, Play/Pause
8. VOL (Volume) Button
TV volume adjustment
9. MENU Button
Press this to bring up the DVD Recorder & VCR’s
setup menu.
10. ENTER/DIRECTION Buttons
(UP/DOWN or LEFT/RIGHT Buttons)
This button functions as a toggle switch.
11. INFO Button
Press this to display current setting or disc status.
12. TITLE LIST/DISC MENU Button
Press this to enter the TITLE LIST/Disc menu.
14 - English
13. SUBTITLE Button
Press this to switch the DVD’s subtitle language.
14. ANYKEY Button
Press this to set the status of the disc that is being
played.
15. REC Button
Press this to make a recording on VCR, DVD-RAM/
±RW/±R discs.
16. TO DVD COPY Button
Press this when you copy from the VCR to the
DVD.
17. REC SPEED Button
Press this to set the desired recording time and
picture quality.
18. VCR Button
Press this when you use a VCR.
19. INPUT SEL. Button
Press this to select AV input signal in external input
mode. (Tuner, AV input, DV input)
20. OPEN/CLOSE Button
Press this to open and close the disc tray.
21. TV POWER Button
22. TV/VCR Button
23. MARKER Button
Press this to bookmark or mark a position while
playing a disc.
24. CH/TRK Button
Press this to select a TV channel/Adjust tape
tracking.
25. RETURN Button
Returns to a previous menu.
26. AUDIO/TV MUTE Button
Press this to access various audio functions.
This operates as sound mute. (TV mode)
27. CANCEL Button
28. PLAY LIST/TITLE MENU Button
Press this to enter the Edit playlist/Title menu.
29. ANGLE Button
Press this to access various camera angles on a
disc (if the disc contains multiple camera angles).
30. ZOOM Button
Zooms in on screen.
31. TIMER REC Button
Press this when you use Timer Recording.
32. TO VCR COPY Button
Press this when you copy from the DVD to the VCR.
33. REC PAUSE Button
Press this to pause during recording.
❚ Key Lock Function
If you do not want others to operate the DVD Recorder &
VCR (for example if you have programmed a timer recording)
you can set the equipment to lock out all button controls.
• Press and hold the INFO button on the remote control for 5
seconds.
The display will show “SAFE” when the feature is activated.
• To resume normal mode, press and hold the INFO button
again for 5 seconds.
“SAFE” will disappear and the DVD Recorder & VCR will
operate normally.
❋ This is a special remote control for the visually impaired, and has Braille points on the
POWER( ), STOP( ) and PLAY( ) buttons.
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:0 PM
Page 15
Connecting &
Setting Up
Quick Overview
A Quick overview presented in this guide will give you
enough information to start using the recorder.
†
Step 2 : Connecting the Video Cable
†
Step 3 : Connecting the Audio Cable
†
Step 4 : Connecting External Devices
†
Step 5 : Connecting the Power Cord
†
Step 6 : Preparing the Remote Control
Quick Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Step 1: Connecting the Antenna Cable . . . . . . . . . . . . . . . . .16
Step 2 : Connecting the Video Cable . . . . . . . . . . . . . . . . . .19
Step 3 : Connecting the Audio Cable . . . . . . . . . . . . . . . . . .22
Step 4 : Connecting External Devices . . . . . . . . . . . . . . . . . .25
• Note to CATV system installer : This reminder is
to call CATV system installer’s attention to Article 820-40
of the National Electrical Code (Section 54 of Canadian
Electrical Code, Part I), that provides guidelines for
proper grounding and, in particular, specifies that the
cable ground shall be connected to the grounding
Step 5 : Connecting the Power Cord . . . . . . . . . . . . . . . . . . .28
system of the building as close to the point of cable title
Step 6 : Preparing the Remote Control . . . . . . . . . . . . . . . . .28
as practical.
English - 15
Connections
Step 1 : Connecting the Antenna Cable
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:0 PM
Page 16
Step 1: Connecting the Antenna Cable
There are several ways to connect your DVD Recorder & VCR. Select the antenna connection that best suits you below.
Connections
Antenna + DVD Recorder & VCR + TV : No Cable box
You can record non-scrambled channels by selecting the channel on the DVD Recorder & VCR. Also use this
method if you watch channels without cable box.
■
Note
If you are using an off-air antenna that has 300ohm twin flat leads, use an external antenna
connector (300-75 ohm adaptor : not supplied)
to connect the antenna to the DVD Recorder &
VCR.
16 - English
■
Note
If you have two separate antennas (one VHF
and the other UHF), use a UHF/VHF combineradaptor (available at most electronics shops) to
connect the antenna to the DVD Recorder &
VCR.
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:0 PM
Page 17
You can record channels by selecting the channel on the cable box. You cannot record one channel while watching
another channel. Be sure that the cable box is turned on.
English - 17
Connections
Antenna + Cable box + DVD Recorder & VCR + TV : Cable box with many scrambled
channels
Connections
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:0 PM
Page 18
Antenna + DVD Recorder & VCR + Cable box + TV : Cable box with a few scrambled
channels
You can record non-scrambled channels by selecting the channel on the cable box. You cannot record scrambled
channels that require a cable box.
18 - English
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:0 PM
Page 19
Step 2 : Connecting the Video Cable
There are several ways to connect your DVD Recorder & VCR. Select one of the video connections on the following pages.
You must use one of the following audio/video connections on this unit.
Connecting to a Video input jack
INPUT
VIDEO
Audio/Video
Cable
Yellow
L
White AUDIO
R
Red
• You will enjoy regular quality images.
• Connect audio cables(white and red) between the
AUDIO OUT jacks on the DVD Recorder & VCR and
AUDIO IN jacks on TV(or AV amplifier).
(See pages 22 ~ 24)
English - 19
Connections
Connect a video(yellow) cable between the VIDEO(yellow) OUT jack on DVD Recorder & VCR and VIDEO(yellow)
IN jack on the TV (or AV amplifier).
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:0 PM
Page 20
Connections
Connecting to an S-Video input jack
Connect an S-Video cable(not supplied) between the S-VIDEO OUT jack on DVD Recorder & VCR and S-VIDEO
IN jack on your TV (or AV amplifier).
INPUT
S-VIDEO
S-Video Cable
(not supplied)
• You will enjoy high quality images. S-Video separates
the picture element into black and white (Y) and color
(C) signals to present clearer images than regular
video input mode.
• Connect audio cables(white and red) between the
AUDIO OUT jacks on the DVD Recorder & VCR and
AUDIO IN jacks on TV(or AV amplifier).
(See pages 22 ~ 24)
20 - English
■
Note
S-Video and Component video output are
available only if your TV supports S-Video
input or Component video input, respectively.
If S-Video or Component video output does
not work, check the TV connections and the
TV input selection settings.
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:2 PM
Page 21
Connecting to Component video input jacks (Y,PB,PR)
COMPONENT
green
• You will enjoy high quality accurate color reproduction
images. Component video separates the picture
element into black and White(Y), blue(PB), red(PR)
signals to present clear and clean images.
• Connect audio cables(white and red) between the
Component AUDIO OUT jacks on the DVD Recorder &
VCR and Component AUDIO IN jacks on TV(or AV
amplifier). (See pages 22 ~ 24)
• Progressive scan
- If the your TV supports Progressive Scan, you can
enjoy higher quality video by pressing the P.SCAN
button. (The component cable has to be connected.)
1. With the unit in stop mode, press the P.SCAN button on the front of the DVD Recorder & VCR.
2. The message ‘Press “Yes” to confirm Progressive
scan mode. Otherwise press “No”’ will appear.
Press the œ √ buttons to select Yes, and then
press the ENTER button.
Component Cable
(not supplied)
green
Y
blue
blue
PB
red
red
PR
■
Note
Compared to standard interlaced video, progressive scan doubles the amount of video lines fed to
your TV, resulting in a more stable, flicker-free,
and clear image than interlaced video. The progressive scan video output jack is used in progressive output mode. This is only available with
TVs that support progressive scan.
■ Progressive Scan Output (480p) Consumers
should note that not all high definition television
sets are fully compatible with this product and may
cause artifacts to be displayed in the picture.
If you experience 480p progressive scan picture
problems, it is recommended that you switch the
connection to the ‘standard definition’ output. If
there are questions regarding TV set compatibility
with this model, please contact our customer
service center at 1-800-SAMSUNG.
English - 21
Connections
Connect Component video cables (not supplied) between the COMPONENT OUT (Y,PB,PR) jacks on
DVD Recorder & VCR and COMPONENT IN (Y,PB,PR) jacks on your TV (or AV amplifier).
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:2 PM
Page 22
Step 3 : Connecting the Audio Cable
Select one of the Audio connections on the following pages.
Connections
Connecting to your TV
This connection will use your TV’s speakers.
INPUT
VIDEO
Audio/Video
Cable
Yellow
L
White AUDIO
R
Red
22 - English
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:2 PM
Page 23
Connecting to a stereo amplifier with analog input jacks
Connections
If your stereo amplifier only has AUDIO INPUT jacks(L and R), use the AUDIO OUT jacks.
Audio/Video
Cable
Red
White
R
L
ANALOG AUDIO
Front(L)speaker
Front(R)speaker
INPUT
English - 23
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:2 PM
Page 24
Connections
Connecting to an AV amplifier with a digital input jack
If your AV amplifier has a Dolby Digital or DTS decoder and a digital input jack, use this connection.
To enjoy Dolby Digital or DTS sound, you will need to set up the audio settings. (See page 36)
Optical Cable
(not supplied)
or
Coaxial Cable
(not supplied)
AV amplifier
Digital Audio
INPUT
Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
“DTS” and “DTS Digital Out” are trademarks of
Digital Theater Systems, Inc.
24 - English
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:2 PM
Page 25
Step 4 : Connecting External Devices
This allows you to connect your DVD Recorder & VCR to other external devices and view or record their outputs.
Connecting a VCR, Set-Top Box(STB) or DVD player to the AV 1 IN or S-VIDEO IN jacks
Connections
Connecting a VCR or external device to AV 1 IN jacks of the DVD Recorder & VCR.
You can record from connected equipment (VCR, STB or DVD).
S-Video Cable
(not supplied)
Audio/Video
Cable
L
R
S-VIDEO
AUDIO
VIDEO
OUTPUT
or
■
Note
You can also use the AV 2 IN jacks on the
front panel of the DVD Recorder & VCR.
■ Press the INPUT SEL. button to select the
AV1 or S-Video input.
■ Copy protected content cannot be recorded.
■ Depending on your input connection, you
must choose AV 1 (Composite) or S-video.
(See page 40)
English - 25
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:2 PM
Page 26
Connections
Connecting a Camcorder to the AV 2 IN jacks
You can also use the AV 2 IN jacks on the front panel of the DVD Recorder & VCR. You can record from connected
equipment, such as a camcorder. When an input source is inserted into AV 2 IN while viewing TV, the input will be
switched to AV 2 IN automatically.
Audio/Video
Cable
L
VIDEO
R
AUDIO
OUTPUT
Camcorder
■
Note
26 - English
If the AV 2 In input source is not selected
automatically, press the INPUT SEL. button
to select the AV 2 input.
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:2 PM
Page 27
Connecting a Camcorder to the DV IN jack
DV Cable
(not supplied)
DV OUT
Camcorder
■
Note
If the input is not selected automatically, use
INPUT SEL. button to select proper input.
English - 27
Connections
If your camcorder has a DV output jack, connect it to the DV input jack of your DVD Recorder & VCR.
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:2 PM
Page 28
Step 5 : Connecting
the Power Cord
Connections
After all connections are complete, plug the power cord
in the wall outlet.
“Auto” appears in the front panel display. This
means that the current time is being set automatically through the antenna under connection(Auto
Program). The setup may take several minutes.
When the DVD Recorder & VCR operates normally, the
current time is automatically set and displayed in the
front panel display.
Step 6 : Preparing the
Remote Control
Install Batteries in the Remote Control
• Open the battery cover on the back of the
remote control.
• Insert two AAA batteries. Make sure that the polarities
(+ and -) are aligned correctly.
• Replace the battery cover.
If the remote control does not operate
properly:
• Check the polarity + - of the batteries (Dry-Cell)
• Check if the batteries are drained.
• Check if the remote sensor is blocked by obstacles.
• Check if there is any fluorescent lighting nearby.
Dispose of batteries according to local
environmental regulations. Do not put them in
the household trash.
28 - English
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:2 PM
Page 29
Setting the Remote Control
You can control part of another manufacturer’s TV
functions with this remote control.
• Buttons that can be controlled on your TV :
TV POWER, INPUT SEL., VOL +/-, CH/TRK ( / ),
TV MUTE, 0~9, 100+.
To determine whether your television is
compatible, follow the instructions below.
1. Switch your television on.
2. Point the remote control towards the television.
3. Press and hold the TV button and enter the two-figure
code simultaneously corresponding to the brand of
your television by pressing the appropriate number
buttons.
Codes
01,14,15,23,31
19
21
30
10
11
06,08,18
28
04
MITSUBISHI 13
Brand
NEWSAN
NOBLEX
PANASONIC
RCA
SANYO
SHARP
SONY
TELEFUNKEN
TOSHIBA
Codes
27
25
12,24
07,29
05,20
02,16,22
03
26
09
ZENITH
17
Result: If your television is compatible with the remote
control, it will switch off.
It is now programmed to operate with the remote
control.
■ If several codes are indicated for your
Note
television brand, try each one in turn until you
find one that works. If you replace the remote
control’s batteries, you must set the brand code
again.
You can then control the television using the
following buttons.
Button
TV POWER
INPUT SEL.
VOL +/-
Function
Used to switch the television on and off.
Used to select an external source.
Used to adjust the volume of the television.
CH/TRK ( / ) Used to select the desired channel.
TV MUTE
Used to toggle the sound on and off.
0~9
Used to input number directly.
100+
Used to select channels over 100.
The various functions may be able to be
Note
controlled on all televisions. If you encounter
problems, operate the television directly.
English - 29
Connections
Brand
SAMSUNG
DAEWOO
EMERSON
GRADIENTE
HITACHI
JVC
LG
LOEWE
MAGNAVOX
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:2 PM
Page 30
System Setup
On-Screen Menu
Navigation
The on-screen menus allow you to enable or disable
various functions on your DVD Recorder & VCR.
Use the following buttons to open and navigate through
the on-screen menus.
DVD-Recorder
Timer Record
System Setup
No Disc
Timer Rec.
Timer Record
√
Setup
Scheduled Record List
√
MOVE
1
2
ENTER
RETURN
EXIT
MENU Button
Press this button on the remote control to open
the on-screen MENU. Press again to exit the
on-screen MENU.
…/†,œ /√ Buttons
Press these buttons on the remote control to
move the selection bar …/†,œ /√ to cycle through
the menu options.
3
ENTER Button
4
RETURN Button
Press this button on the remote control to confirm
any new settings.
On-Screen Menu Navigation..............................................30
Auto Clock Set ..................................................................31
Manual Clock Set ..............................................................32
Channel Set .......................................................................33
Auto Channel Memory.......................................................33
Channel Add/Delete ..........................................................34
RF Output Channel............................................................34
Setting Up the Language Options .....................................35
Setting Up the Audio Options ...........................................36
Setting Up the Display (Video) Options ............................37
Setting Up the Parental Control ........................................38
VCR Setting ......................................................................39
Video Input .......................................................................40
DVD EP Mode Time .........................................................41
Automatic Chapter Creator ...............................................41
Quick Recording .................................................................42
30 - English
Press this button on the remote control to return to
the previous MENU screen displayed or to exit the
on-screen MENU.
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:2 PM
Page 31
Press the …† buttons to select Auto Clock Set,
then press the ENTER or √ button.
4
Auto Clock Set
DVD-Recorder
Auto Clock Set
No Disc
Timer Rec.
Clock Data CH
: Automatic
√
Setup
Time Zone
: Automatic
√
Daylight Saving
: Automatic
√
This menu is used to set the current time. You need to
set the time to use timer recording.
MOVE
You must have the antenna connected to set
Note
With the unit in Stop mode/No Disc mode, press
the MENU button.
DVD-Recorder
RETURN
EXIT
■ If your clock is set to the wrong time zone or
Note
5
daylight saving, you can adjust these settings
without turning off the Auto Clock Set function.
Press the …† buttons to select the sub menu
(Clock Data CH, Time Zone or Daylight Saving),
then press the ENTER or √ button.
Timer Record
No Disc
Timer Rec.
Timer Record
√
Setup
Scheduled Record List
√
Clock Data CH
MOVE
2
ENTER
RETURN
Press the …† buttons to select a channel that
carries a time signal, then press the ENTER button.
Select Auto to set the channel automatically.
EXIT
Press the …† buttons to select Setup, then press
the ENTER or √ button.
DVD-Recorder
Clock Data CH
No Disc
Timer Rec.
DVD-Recorder
Setup
Select channel :
Setup
Auto
No Disc
Timer Rec.
System
√
Setup
Clock Set
√
Channel Set
√
Language
√
Audio
√
Video
√
Parental Control
MOVE
3
ENTER
MOVE
ENTER
EXIT
√
RETURN
Time Zone
EXIT
Press the …† buttons to select Clock Set, then
press the ENTER or √ button.
DVD-Recorder
Press the …† buttons to select the time zone of
your area, then press the ENTER or √ button.
Select Automatic to set the time zone automatically.
Clock Set
DVD-Recorder
No Disc
Timer Rec.
Auto Clock Set
√
Setup
Manual Clock Set
√
Auto Clock Set
No Disc
Timer Rec.
Clock Data CH
Setup
Time Zone
Daylight Saving
MOVE
RETURN
ENTER
RETURN
Automatic
Atlantic
Eastern
Central
Mountain
Pacific
Alaska
Hawaii
EXIT
MOVE
ENTER
RETURN
EXIT
English - 31
System Setup
1
the Auto Clock. See pages 16~18 for Antenna
Connections.
The Clock will be automatically set when you
turn off the recorder.
ENTER
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:2 PM
Page 32
Daylight Saving
3
Press the …† buttons to select Yes or No, then
press the ENTER or √ button.
Select Automatic to set the daylight saving
automatically.
DVD-Recorder
Press the …† buttons to select Clock Set, then
press the ENTER or √ button.
DVD-Recorder
Clock Set
No Disc
Timer Rec.
Auto Clock Set
√
Setup
Manual Clock Set
√
Auto Clock Set
No Disc
Timer Rec.
Clock Data CH
: Automatic
√
Setup
Time Zone
: Automatic
: Automatic
Automatic
Yes
No
√
Daylight Saving
System Setup
MOVE
ENTER
RETURN
MOVE
ENTER
RETURN
EXIT
√
4
EXIT
Manual Clock Set
Press the …† buttons to select Manual Clock
Set, then press the ENTER or √ button.
DVD-Recorder
Manual Clock Set
No Disc
Timer Rec.
Setup
Month Day
01
01
Year
2006
Hour Minute AM/PM
12
00
AM
SUN
Press numeric keys or …† keys.
If Auto Setup fails to set the DVD Recorder & VCR’s internal clock by locating a local TV station, follow these steps
to set the date and time manually.
Note
1
For accurate Timer Recording, your DVD Recorder
& VCR's internal clock must be set correctly.
With the unit in Stop mode/No Disc mode, press
the MENU button.
DVD-Recorder
Timer Record
No Disc
Timer Rec.
Timer Record
√
Setup
Scheduled Record List
√
MOVE
2
ENTER
RETURN
EXIT
Press the …† buttons to select Setup, then press
the ENTER or √ button.
DVD-Recorder
Setup
No Disc
Timer Rec.
System
√
Setup
Clock Set
√
Channel Set
√
Language
√
Audio
√
Video
√
Parental Control
MOVE
32 - English
ENTER
√
RETURN
EXIT
MOVE
5
ENTER
RETURN
EXIT
Press the …†œ √ buttons to select the Current Date
and Time, then press the ENTER button.
When the current time is stored in memory and
then the set is powered off, the current time will
appear in the front panel display.
…† : Sets the value
You can set the value using the number (0~9)
buttons.
œ √: Moves to items
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:2 PM
Page 33
4
Channel Set
Press the …† buttons to select Antenna/Cable
TV, then press the ENTER or √ button.
DVD-Recorder
Channel Set
No Disc
This feature allows you to manually set the DVD
Recorder & VCR’s tuner band to Antenna or Cable,
whichever you connected to the Antenna In jack during
initial setup.
• Use this setting only if Auto Setup detected the
incorrect tuner band, i.e. channels are coming in on
the wrong channel numbers.
Timer Record
√
Scheduled Record List
√
MOVE
2
ENTER
RETURN
√
ENTER
RETURN
EXIT
• Cable TV - Select this if the DVD Recorder &
VCR is connected to a cable TV. (See page 17)
Auto Channel Memory
EXIT
Press the …† buttons to select Setup, then press
the ENTER or √ button.
DVD-Recorder
Setup
No Disc
Timer Rec.
System
√
Setup
Clock Set
√
Channel Set
√
Language
√
Audio
√
Video
√
Parental Control
MOVE
3
√
RF Output Channel : CH3
• Antenna - Select this if the DVD Recorder &
VCR is connected to an indoor or outdoor
VHF/UHF antenna. (See pages 16, 18)
No Disc
Setup
√
Channel Add/Delete
Select the Antenna or Cable TV(Signal Source)
that matches the antenna connection you selected
on pages 16~18.
Timer Record
Timer Rec.
√
Auto Channel Memory
Cable TV
MOVE
With the unit in Stop mode/No Disc mode, press
the MENU button.
DVD-Recorder
Antenna/Cable TV Antenna
: Cable TV
Setup
ENTER
√
RETURN
1
With the unit in Stop mode/No Disc mode, press
the MENU button.
2
Press the …† buttons to select Setup, then press
the ENTER or √ button.
3
Press the …† buttons to select Channel Set,
then press the ENTER or √ button.
EXIT
Press the …† buttons to select Channel Set,
then press ENTER or √ button.
DVD-Recorder
Auto Channel Memory will automatically seek and store
all active channels in your area.
Channel Set
No Disc
DVD-Recorder
Channel Set
Timer Rec.
Antenna/Cable TV
Setup
Auto Channel Memory
√
No Disc
Channel Add/Delete
√
Timer Rec.
Antenna/Cable TV
RF Output Channel : CH3
√
Setup
Auto Channel Memory
√
Channel Add/Delete
√
RF Output Channel : CH3
√
MOVE
ENTER
: Antenna
RETURN
√
: Antenna
√
EXIT
MOVE
ENTER
RETURN
EXIT
English - 33
System Setup
1
Timer Rec.
00995J(00)_VR330_AFS-Eng1
4
2006.4.13
7:2 PM
Page 34
Press the …† buttons to select Auto Channel
Memory, then press the ENTER or √ button.
4
Press the …† buttons to select Channel
Add/Delete, then press the ENTER or √ button.
DVD-Recorder
Channel Add/Delete
No Disc
Timer Rec.
Auto Channel Memory
Setup
Select channel :
1
Total channel numbers : 02/125
Saved channel :
1%
Stop
Add
• The DVD Recorder & VCR will automatically
search for all available channels in the selected
tuner band. This procedure may take a few
minutes to complete.
• When finished, the lowest channel will be displayed.
• If you want to stop or cancel scanning, press the
ENTER button. Then select ‘YES’.
Channel Add/Delete
5
ENTER
RETURN
EXIT
Press the …† or number buttons to select the
channels you want to add or delete on the Select
channel screen. Then, press the ENTER button.
• Using CH/TRK ( / ) buttons for channel selection
allows the user to add/delete one channel at a time.
• Using …† buttons for channel selection jumps to
the next channel memorized in Auto Channel
Memory.
6
Press the œ √ buttons to select Add or Delete,
then press the ENTER button.
DVD-Recorder
Channel Add/Delete
No Disc
Timer Rec.
Setup
Select channel :
11
Channel is added.
Add
Use this feature if Auto Channel Memory missed a
channel that you would like to add or if you wish to
remove a channel.
1
With the unit in Stop mode/No Disc mode, press
the MENU button.
2
Press the …† buttons to select Setup, then press
the ENTER or √ button.
3
Press the …† buttons to select Channel Set, then
press the ENTER or √ button.
DVD-Recorder
NUMBER
ENTER
Delete
RETURN
EXIT
RF Output Channel
When you connect the DVD Recorder & VCR to your
TV with the RF Antenna Cable, follow the steps below
to set the RF Output Channel.
Channel Set
No Disc
Timer Rec.
Antenna/Cable TV
Setup
Auto Channel Memory
√
Channel Add/Delete
√
RF Output Channel : CH3
√
MOVE
34 - English
ENTER
: Antenna
RETURN
√
EXIT
1
With the unit in Stop mode/No Disc mode, press
the MENU button.
2
Press the …† buttons to select Setup, then press
the ENTER or √ button.
System Setup
System Setup
NUMBER
Delete
00995J(00)_VR330_AFS-Eng1
3
2006.4.13
7:2 PM
Page 35
Press the …† buttons to select Channel Set,
then press ENTER or √ button.
DVD-Recorder
2
Press the …† buttons to select Setup, then press
the ENTER or √ button.
DVD-Recorder
Channel Set
Setup
No Disc
No Disc
Timer Rec.
Antenna/Cable TV
Setup
Auto Channel Memory
: Antenna
√
Timer Rec.
System
√
√
Setup
Clock Set
√
√
Channel Add/Delete
√
Channel Set
RF Output Channel : CH3
√
Language
√
Audio
√
Video
√
Parental Control
MOVE
4
ENTER
RETURN
Press the …† buttons to select RF Output
Channel, then press the ENTER or √ button.
DVD-Recorder
MOVE
EXIT
3
Channel Set
ENTER
√
RETURN
EXIT
Press the …† buttons to select Language, then
press the ENTER or √ button.
Language setup menu will be displayed.
No Disc
Timer Rec.
Antenna/Cable TV
Setup
Auto Channel Memory
√
Channel Add/Delete
√
: Antenna
MOVE
ENTER
RETURN
DVD-Recorder
Timer Rec.
Audio
: Original
√
Setup
Subtitle
: Automatic
√
Disc Menu
: English
√
On-Screen Menu : English
√
√
EXIT
MOVE
5
Language
No Disc
System Setup
System Setup
RF Output Channel : CH3
CH4
√
Press the …† buttons to select CH3 or CH4, then
press the ENTER or √ button.
The message "Please tune your TV to channel 3
(4)" will appear on the screen. Change your TV
channel to CH3 or CH4 to match the RF Output
Channel of the DVD Recorder & VCR.
4
ENTER
RETURN
EXIT
Press the …† buttons to select the desired
language option, press the ENTER or √ button.
DVD-Recorder
Language
No Disc
1
Audio
Setup
Subtitle
: Original
Original
MOVE
…
: English
Automatic
Français
Disc Menu
: English
Deutsch
On-Screen Menu : English
Español
Italiano
Nederlands
Korean
Setting Up the
Language Options
If you set audio, subtitle, disc menu and on-screen
menu language in advance, they will come up
automatically every time you watch a movie.
If the selected language is not recorded on the disc,
the original pre-recorded language is selected.
Timer Rec.
ENTER
RETURN
√
√
√
√
†
EXIT
• Audio: For the disc audio language.
• Subtitle: For the disc subtitles.
• Disc Menu: For the disc menu contained on the
disc.
• On-Screen Menu: For the on-screen menu of
your DVD Recorder & VCR.
5
Press the …† buttons to select the desired
language, then press the ENTER or √ button.
With the unit in Stop mode/No Disc mode, press
the MENU button.
■ Press the RETURN or œ button to return to the
Note
previous menu. Press the MENU button to exit
the menu.
■ The selected language will only appear if it is
supported on the disc.
English - 35
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:2 PM
Page 36
Setting Up the Audio
Options
Allows you to setup the audio device and sound status
settings depending on the audio system in use.
Digital Output
1. PCM : Converts to PCM(2CH) 48kHz audio.
Select PCM when using the Analog Audio
Outputs.
2. Bitstream : Converts to Dolby Digital Bitstream
(5.1CH). Select Bitstream when using
the Digital Audio Outputs.
Be sure to select the correct Digital Output or
1
With the unit in Stop mode/No Disc mode, press
the MENU button.
2
Press the …† buttons to select Setup, then press
the ENTER or √ button.
DVD-Recorder
Setup
System Setup
No Disc
Timer Rec.
System
√
Setup
Clock Set
√
Channel Set
√
Language
√
Audio
√
Video
√
Parental Control
√
MOVE
3
ENTER
RETURN
Audio
No Disc
Timer Rec.
Digital Output
: PCM
√
Setup
DTS
: Off
√
Dynamic Compressiom : On
√
MOVE
ENTER
RETURN
EXIT
4
Press the …† buttons to select the desired audio
option, then press the ENTER or √ button.
5
Press the …† buttons to select the desired item,
then press the ENTER or √ button.
■ Press the RETURN or œ button to return to the
Note
previous menu.
Press the MENU button to exit the menu.
36 - English
DTS
1. Off : Doesn’t output digital signal.
2. On : Outputs DTS Bitstream via digital output
only. Select DTS when connecting to a DTS
Decoder.
When DTS soundtrack is played, sound is not
Note
output from Analog Audio Output.
EXIT
Press the …† buttons to select Audio, then press
the ENTER or √ button.
Audio setup menu will be displayed.
DVD-Recorder
no audio will be heard.
Note
Dynamic Compression
This is only active when a Dolby Digital signal is
detected.
1. On : When the Movie soundtracks are played at
low volume or from small speakers, the
system can apply appropriate compression
to make low-level content more intelligible
and prevent dramatic passages from getting
too loud.
2. Off : You can enjoy the movie with the standard
Dynamic Range.
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:2 PM
Page 37
Setting Up the
Display(Video) Options
This function allows you to setup the TV screen
settings.
1
With the unit in Stop mode/No Disc mode, press
the MENU button.
2
Press the …† buttons to select Setup, then press
the ENTER or √ button.
DVD-Recorder
TV Aspect
Depending on the type of television you have, you
may want to adjust the screen setting. (aspect ratio)
• 4:3 Letter Box : Select when you want to see the
total 16:9 ratio screen DVD supplies, even though you have a TV
with a 4:3 ratio screen. Black
bars will appear at the top and
bottom of the screen.
• 4:3 Pan & Scan : Select this for a conventional
size TV when you want to see
the central portion of the 16:9
screen. (Extreme left and right
side of movie picture will be cut
off.)
• 16:9 Wide : You can view the full 16:9 picture on
your wide-screen TV.
Setup
No Disc
System
√
Setup
Clock Set
√
Channel Set
√
Language
√
Audio
√
Video
√
Parental Control
√
MOVE
3
ENTER
RETURN
EXIT
Press the …† buttons to select Video, then press
the ENTER or √ button.
Video option menu will be displayed.
DVD-Recorder
Video
No Disc
Timer Rec.
TV Aspect
: 16:9 Wide
√
Setup
Input Level
: Darker
√
Black Level
: 7.5 IRE
√
3D Noise Reduction : Off
MOVE
ENTER
RETURN
√
EXIT
4
Press the …† buttons to select the desired video
option, then press the ENTER or √ button.
5
Press the …† buttons to select the desired item,
then press the ENTER or √ button.
Input Level
Adjusts the level of the input signal.
• Darker : If you feel the screen is too light
and you want to make the screen
darker.
• Lighter : If you feel the screen is too dark
and you want to make the screen
lighter.
Black Level
Adjusts the black level of the screen.
• 7.5 IRE : This will enhance the black level for
increased brightness/contrast when
viewing DVDs.
Select this when you want to make the
screen lighter.
• 0 IRE : This is the standard NTSC reference black
level for consistent brightness/contrast
across all sources.
Select this when you want to make the
screen darker.
3D Noise Reduction
• Off : Normal
• On : Select to remove noise from the screen.
Press the RETURN or œ button to return to the
Note
previous menu.
Press the MENU button to exit the menu.
This function depends on disc type. It may not
Note
work for some disc types.
IRE: Short for the Institute of Radio Engineers.
An IRE unit is a relative unit of measure
equaling 1/140th of the peak-to peak (p-p)
video amplitude.
English - 37
System Setup
Timer Rec.
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:2 PM
Page 38
Setting Up the Parental
Control
5
The Re-enter Password screen appears to confirm
the password. Enter your password again, and
then press the ENTER or √ button.
DVD-Recorder
Parental Control
No Disc
Timer Rec.
Password
:Off
Off
The Parental Control function works in conjunction with
DVDs that have been assigned a rating - which helps
you control the types of DVDs that your family watches.
There are up to 8 rating levels on a disc.
With the unit in Stop mode/No Disc mode, press
the MENU button on the remote control.
2
Press the …† buttons to select Setup, then press
the ENTER or √ button.
System Setup
1
MOVE
6
Setup
No Disc
Timer Rec.
System
√
Setup
Clock Set
√
Channel Set
√
Language
√
Audio
√
Video
√
Parental Control
MOVE
3
ENTER
RETURN
EXIT
Press the …† buttons to select On, then press
the ENTER or √ button.
The Parental Control screen appears.
previous menu. Press the MENU button to exit the
menu.
Refer to Troubleshooting if you forget your password. (See page 92)
About the Rating Level
√
RETURN
EXIT
1
Press the …† buttons to select Parental Control,
then press the ENTER or √ button.
DVD-Recorder
ENTER
Press the RETURN or œ button to return to the
Note
DVD-Recorder
√
On
Setup
Press the …† buttons to select Rating Level,
then press the ENTER or √ button.
DVD-Recorder
Parental Control
No Disc
Timer Rec.
Password
: On
√
Setup
Rating Level
: Level 1 Kids
√
Change Password
Parental Control
√
No Disc
Timer Rec.
Setup
Create the password
MOVE
ENTER
DVD-Recorder
NUMBER
4
ENTER
RETURN
EXIT
Parental Control
No Disc
EXIT
Timer Rec.
Password
√
Setup
Rating Level
√
Create a 4-digit password using the 0 to 9 buttons
on the remote control.
DVD-Recorder
RETURN
MOVE
Parental Control
:On
Level 8 Adults
:Level
Level71 Kids
Level 6
Change Password Level 5
Level 4
Level 3
Level 2
Level 1 Kids
ENTER
RETURN
√
EXIT
No Disc
Timer Rec.
Setup
Confirm the password
2
NUMBER
38 - English
ENTER
RETURN
EXIT
Press the …† buttons to select the rating level
you want, then press the ENTER or √ button.
For example, if you select up to Level 6, discs that
contain Level 7, 8 will not play. A larger number
indicates that the program is intended for adult
use only.
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:2 PM
Page 39
About the Change Password
1
VCR Setting
Press the …† buttons to select Change Password,
then press the ENTER or √ button.
DVD-Recorder
Parental Control
No Disc
Timer Rec.
Password
: On
√
Setup
Rating Level
: Level 1 Kids
√
Change Password
MOVE
ENTER
DVD-Recorder
This function allows you to setup the VCR.
√
RETURN
1
With the unit in Stop mode/No Disc mode, press
the MENU button.
2
Press the …† buttons to select Setup, then press
the ENTER or √ button.
EXIT
Change Password
No Disc
Timer Rec.
Setup
DVD-Recorder
Enter the password
Setup
No Disc
ENTER
RETURN
System
√
Setup
Clock Set
√
Channel Set
√
Language
√
Audio
√
Video
√
EXIT
Parental Control
MOVE
2
Enter the 4-digit password using the number buttons
on the remote control.
The ‘Confirm the password’ message will be
displayed.
DVD-Recorder
3
Change Password
3
Confirm the password
ENTER
RETURN
EXIT
Enter your password again.
Press the RETURN or œ button to return to the
Note
EXIT
Press the …† buttons to select System, then
press the ENTER or √ button.
System
No Disc
Timer Rec.
NUMBER
√
RETURN
DVD-Recorder
No Disc
Setup
ENTER
System Setup
NUMBER
Timer Rec.
previous menu.
Press the MENU button to exit the menu.
Timer Rec.
VCR
Setup
Video Input
MOVE
4
√
: AV 1
√
DVD EP Mode Time : 6 Hours
√
Chapter Creator
: Off
√
Quick Recording : Off
√
ENTER
RETURN
EXIT
Press the …† buttons to select VCR, then press
the ENTER or √ button.
DVD-Recorder
VCR
No Disc
Timer Rec.
Tape Length
: T120
√
Setup
Auto Play
: On
√
Auto Repeat
: Off
√
ENTER
RETURN
MOVE
EXIT
English - 39
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:2 PM
Page 40
5
Press the …† buttons to select the desired VCR
option, then press the ENTER or √ button.
6
Press the …† buttons to select the desired item,
then press the ENTER or √ button.
You can watch video from an external component
through the AV 1(Composite) or S-video input jacks.
Tape Length
This information is usually printed on the tape box.
The menu cycles through: T-120, T-160 or T-180.
Once the type of cassette is set, the VCR can display the amount of time remaining on the tape when
you press the INFO button.
DVD-Recorder
VCR
No Disc
System Setup
Video Input
Timer Rec.
Tape Length
T120
√
Setup
Auto Play
T160
On
T180
Off
√
Auto Repeat
1
With the unit in Stop mode/No Disc mode, press
the MENU button.
2
Press the …† buttons to select Setup, then press
the ENTER or √ button.
DVD-Recorder
√
Setup
No Disc
MOVE
ENTER
RETURN
Timer Rec.
System
√
Setup
Clock Set
√
Channel Set
√
Language
√
Audio
√
Video
√
EXIT
Parental Control
Auto Play
MOVE
ENTER
√
RETURN
EXIT
If you want your videotapes to play automatically
when you insert them, turn on Auto Play.
• Off : Auto play is disabled.
• On : The VCR will automatically begin playing a
video tape when it is inserted, as long as the
safety tab of the cassette has been removed.
3
Press the …† buttons to select System, then
press the ENTER or √ button.
DVD-Recorder
System
No Disc
DVD-Recorder
VCR
Timer Rec.
VCR
Setup
Video Input
No Disc
Timer Rec.
Setup
Tape Length
: T120
√
Auto Play
: Off
On
√
Auto Repeat
: On
Off
√
ENTER
RETURN
√
Chapter Creator
: Off
√
Quick Recording : Off
√
ENTER
RETURN
EXIT
EXIT
4
Auto Repeat
Press the …† buttons to select Video Input, then
press the ENTER or √ button.
DVD-Recorder
It sets the VCR to play a tape repeatedly (unless a
tape control is activated :Stop, Fast Forward or
Rewind).
DVD-Recorder
√
DVD EP Mode Time : 6 Hours
MOVE
MOVE
√
: AV 1
System
No Disc
Timer Rec.
VCR
Setup
Video Input
VCR
√
:AV
AV 11
√
DVD EP Mode Time :S-Video
6 Hours
√
Chapter Creator
: Off
√
Quick Recording : Off
√
No Disc
Timer Rec.
Tape Length
: T120
√
Setup
Auto Play
: On
√
Auto Repeat
: Off
Off
On
√
MOVE
40 - English
ENTER
RETURN
EXIT
MOVE
5
ENTER
RETURN
EXIT
Press the …† buttons to select AV 1 or
S-Video, then press the ENTER or √ button.
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:2 PM
Page 41
DVD EP Mode Time
You can set the EP(Extended Play)mode’s time setting
to 6 or 8hours.
1
With the unit in Stop mode/No Disc mode, press
the MENU button.
2
Press the …† buttons to select Setup, then press
the ENTER or √ button.
Automatic Chapter
Creator
A DVD-Video consists of ‘Titles’ and ‘Chapters’.
When you record one program, it makes one Title.
If you use this function, the Title will be divided into
Chapters.
(V mode)
DVD-Recorder
Timer Rec.
System
√
2
Press the …† buttons to select Setup, then press
the ENTER or √ button.
Setup
Clock Set
√
Channel Set
√
Language
√
Audio
√
Video
√
Parental Control
√
ENTER
RETURN
DVD-Recorder
EXIT
Title List
System
√
Disc Manager
Clock Set
√
Channel Set
√
Language
√
Audio
√
Video
√
Timer Rec.
Setup
Copy
3
Press the …† buttons to select System, then
press the ENTER or √ button.
4
Press the …† buttons to select DVD EP Mode
Time, then press the ENTER or √ button.
DVD-Recorder
System
No Disc
Timer Rec.
VCR
Setup
Video Input
Parental Control
MOVE
Hours
: 8Off
Quick Recording : Off
ENTER
√
RETURN
EXIT
3
Press the …† buttons to select System, then
press the ENTER or √ button.
4
Press the …† buttons to select Chapter Creator,
then press the ENTER or √ button.
√
DVD-Recorder
√
RETURN
System
√
DVD-RW(V)
√
Title List
VCR
Disc Manager
Video Input
Timer Rec.
MOVE
ENTER
√
: AV 1
DVD EP Mode Time : 66 Hours
Hours
Chapter Creator
Setup
DVD-RW(V)
EXIT
Setup
√
: AV 1
DVD EP Mode Time : 6 Hours
√
√
: Off
Off
√
Quick Recording : On
Off
√
Chapter Creator
Copy
5
MOVE
Press the …† buttons to select 6 Hours or
8 Hours, then press the ENTER or √ button.
ENTER
RETURN
EXIT
5
Press the …† buttons to select On, then press
the ENTER or √ button.
Press the MENU button to exit the menu.
6
Set the recording speed by pressing the REC
SPEED button on the remote (see page 60 for
more information on recording speeds).
English - 41
System Setup
With the unit in Stop mode/No Disc mode, press
the MENU button.
Setup
No Disc
MOVE
1
00995J(00)_VR330_AFS-Eng1
7
2006.4.13
7:2 PM
Page 42
Press the REC button to start recording.
The message "Do you want to create the chapter
menu after this recording?" is displayed.
Quick Recording
Do you want to create the chapter menu
after this recording?
Yes
8
It takes about 10 seconds for a disc to load (initialize)
every time you turn on the unit. To bypass this initialization process, you can set the Quick Recording feature
to On. This enables you to record immediately without
having to wait for the disc to load.
No
Press the œ √ buttons to select Yes and press
the ENTER button and recording begins.
In XP and SP mode, you must record at least 5
minutes to create a chapter. In LP and EP mode,
15 minutes.
1
2
System Setup
Press the STOP button to stop recording.
9
10
With the unit in Stop mode/No Disc mode, press the
MENU button.
Press the …† buttons to select Setup, then press the
ENTER or √ button.
DVD-Recorder
Setup
No Disc
To display the created titles, finalize the disc
(see page 87) and then press the TITLE MENU
button. The title menu will be displayed.
Timer Rec.
System
√
Setup
Clock Set
√
Channel Set
√
Language
√
Audio
√
Video
√
Parental Control
1/1
JAN/01/2006
12:00 AM CH1
JAN/01/2006
12:30 AM CH1
JAN/01/2006
01:00 AM CH1
JAN/01/2006
01:30 AM CH1
MOVE
3
ENTER
√
RETURN
Press the …† buttons to select System, then press
the ENTER or √ button.
DVD-Recorder
Previous
11
Top
1/1
2
System
No Disc
Next
To display the created chapters, select the
desired Title and then press the DISC MENU
button. The chapter menu for the selected Title
will be displayed.
1
EXIT
3
Timer Rec.
VCR
Setup
Video Input
√
DVD EP Mode Time : 6 Hours
√
Chapter Creator
: Off
√
Quick Recording : Off
√
MOVE
4
√
: AV 1
ENTER
RETURN
EXIT
Press the …† buttons to select Quick Recording,
then press the ENTER or √ button.
DVD-Recorder
System
No Disc
Previous
Top
Timer Rec.
VCR
Setup
Video Input
Next
√
: AV 1
√
DVD EP Mode Time : 6 Hours
√
Chapter Creator
: Off
√
Quick Recording : Off
Off
√
On
On DVD-RW discs, additional chapters and
Note
titles can be added to a finalized disc by
unfinalizing and recording again.On DVD-R
discs, once finalized, no additional chapters or
titles can be recorded.
MOVE
5
ENTER
RETURN
EXIT
Press the …† buttons to select On, then press the
ENTER or √ button.
The Automatic Chapter Creator function does
CAUTION
not work during Timer Recording or when you
turn the power off.
DVD-R discs cannot be unfinalized.
42 - English
Note
The Quick Recording is set to Off as default.
If this function is set to on, power consumption
will be increased when the unit is powered off.
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:2 PM
Page 43
Before Playing
Playback
Read the following information before playing a disc.
This section introduces basic functions of playback by disc type.
Dolby Digital
DTS
Digital Audio
Region code (DVD-Video only)
Both the DVD Recorder & VCR and the discs are coded
by region. These regional codes must match in order for
the disc to play. If the codes do not match, the disc will not
play. The Region Number for this DVD Recorder & VCR is
described on the rear panel of the DVD Recorder & VCR.
Disc types that can be played
Disc Types
Stereo
NTSC broadcast system in U.S.A, Canada,
Korea, Japan,etc.
MP3
DVD-VIDEO
AUDIO-CD
JPEG CD-R/-RW
◆ DVD Playback
Before Playing ...................................................................43
MP3 CD-R/-RW
Disc Logo
Recorded
content
Single sided(5”)
Double sided(5”)
Single sided(3.5”)
Double sided(3.5”)
Single sided(5”)
AUDIO
Single sided(3.5”)
Single sided(5”)
JPEG Images
Single sided(3.5”)
Single sided(5”)
MP3 Audio
Single sided(3.5”)
VIDEO
AUDIO
Single sided(5”)
(4.7GB)
Using the Disc Menu and Title Menu ...............................45
DVD-RAM
Slow Motion Play / Step Motion Play ...............................46
VIDEO
AUDIO
Double sided(5”)
(9.4GB)
About ANYKEY .................................................................46
Repeat Playback ................................................................47
Selecting the Subtitle & Audio Language.........................48
Changing the Camera Angle.............................................49
DVD-RW
VIDEO
AUDIO
5” (4.7GB)
Zooming-In .......................................................................49
Using the Bookmarks .......................................................50
Single layer(5”)
(4.7GB)
Using the Markers ...........................................................51
Playing back an Audio CD (CD-DA)................................52
Playing back an MP3 Disc ................................................53
DVD-R
VIDEO
AUDIO
Dual layer(5”)
(8.5GB)
Repeat Playback of an Audio/MP3 Disc............................54
Play Option Mode..............................................................54
To Program Tracks ............................................................55
Playing a Picture Disc .......................................................55
DVD+RW
VIDEO
AUDIO
5” (4.7GB)
◆ VCR Playback
Single layer(5”)
(4.7GB)
Playing the VCR................................................................56
Tracking.............................................................................56
Special VCR Playback Features ........................................57
S-VHS Playback ...............................................................57
Variable Search System.....................................................57
DVD+R
VIDEO
AUDIO
Dual layer(5”)
(8.5GB)
Max. Playing Time
or minute.
240
480
80
160
74
20
1 hr (XP: Excellent Quality)
2 hrs (SP: Standard Quality)
4 hrs (LP: Long Playback)
6 hrs or 8 hrs (EP:Extended)
2 hrs (XP: Excellent Quality)
4 hrs (SP: Standard Quality)
8 hrs (LP: Long Playback)
12 or 16 hrs (EP:Extended)
1 hr (XP: Excellent Quality)
2 hrs (SP: Standard Quality)
4 hrs (LP: Long Playback)
6 or 8 hrs (EP:Extended)
1 hr (XP: Excellent Quality)
2 hrs (SP: Standard Quality)
4 hrs (LP: Long Playback)
6 or 8 hrs (EP:Extended)
2 hrs (XP: Excellent Quality)
4 hrs (SP: Standard Quality)
8 hrs (LP: Long Playback)
11 or 15 hrs (EP:Extended)
1 hr (XP: Excellent Quality)
2 hrs (SP: Standard Quality)
4 hrs (LP: Long Playback)
6 or 8 hrs (EP:Extended)
1 hrs (XP: Excellent Quality)
2 hrs (SP: Standard Quality)
4 hrs (LP: Long Playback)
6 or 8 hrs (EP:Extended)
2 hrs (XP: Excellent Quality)
4 hrs (SP: Standard Quality)
8 hrs (LP: Long Playback)
11 or 15 hrs (EP:Extended)
English - 43
Playback
Playing a Disc ...................................................................44
Using the Search & Skip Functions ..................................45
Disc Shape
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:2 PM
Page 44
Discs that cannot be played
• DVD-Video with a region number other than “1” or “ALL”
• 3.9 GB DVD-R Disc for Authoring.
• A DVD±R/DVD-RW(V) disc which has been recorded and
not finalized in a different manufacturer's recorder.
• PAL discs
• DVD-ROM/PD/MV-Disc/ DivX Video Disc, etc
• Video CD/CVD/SVCD/CD-ROM/CDV/CD-G/CD-I
This DVD Recorder & VCR can only operate with
Playback
Note
discs that are compatible with DVD-RAM Standard
Version 2.0.
Playback and/or recording may not work for some
types of discs or when specific operations, such as
angle change and aspect ratio adjustment, are
being performed. Information about the disc is
written in detail on the box. Please refer to this if
necessary.
Do not allow the disc to become dirty or scratched,
fingerprints, dirt, dust, scratches and deposits of
cigarette smoke on the recording surface may
make it impossible to use the disc for recording.
DVD-RAM/±RW/±R discs may not be able to play
on some DVD players, depending on the player,
disc and the condition of the recording.
Discs with PAL programs recorded on them cannot be played using this product.
1
Press the OPEN/CLOSE button.
2
Place a disc gently into the tray with the disc’s
label facing up.
3
Press OPEN/CLOSE button to close the disc tray.
• Your DVD Recorder & VCR closes the disc
tray and plays the disc automatically.
• The recorder does not play discs automatically
after being powered on initially.
• When the recorder is powered on and a disc is
in the tray, the unit will be activated and wait in
stop status. Press the PLAY button to start playback.
4
Press the STOP button to stop playback.
When you stop playing the disc, the DVD
Recorder & VCR remembers where you stopped.
When you press PLAY button again, it will pick up
where you left off. (unless the disc is removed or
the DVD Recorder & VCR is unplugged, or if you
press the STOP button twice.) This function is
only applicable to DVD-VIDEO, DVD-RAM,
DVD±RW, DVD±R or Audio CDs (CD-DA).
Note
Playing a Disc
Do not move your DVD Recorder & VCR while
playing, as this may cause damage to the disc.
CAUTION
Make sure to press the OPEN/CLOSE button
to open or close the disc tray.
Do not push the disc tray while it is being
44 - English
opened or closed, as this may cause a product
malfunction.
Do not place foreign materials on or in the disc
tray.
Some functions may perform differently or be
disabled depending on the disc type. If this
occurs, refer to the instructions written on the
disc case.
Be especially careful that children's fingers are
not caught between the disc tray and the tray
chassis when it closes.
After turning power on, it will take a few
seconds until the DVD Recorder & VCR
operates.
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:2 PM
Page 45
Using the Disc Menu
and Title Menu
Some discs contain a dedicated menu system that
allows you to select special functions for title, chapters,
audio track, subtitles, film previews, information on
characters, etc.
For DVD-VIDEO disc
Press the DISC MENU button to enter the disc
menu of the disc.
1
Using the Search & Skip
Functions
Searching through a Chapter or Track
During the playback, press the SEARCH œœ or √√
button on the remote control. Each time you press
the SEARCH button, the playback speed will
change as follows.
√√ Fast 1/œœ Fast 1➝ √√ Fast 2/œœ Fast 2➝
DVD-VIDEO/
DVD-RAM/DVD±RW √√ Fast 3/œœ Fast 3➝ √√ Fast 4/œœ Fast 4➝
DVD±R
√√ Fast 5/œœ Fast 5➝ √√ Fast 6/œœ Fast 6
• Move to the setup menu related to playback operation.
• You can select audio language and subtitle etc.,
provided by the disc.
2
For DVD-RAM/DVD±RW/DVD±R disc
1
Press the TITLE LIST button to display title list.
Title List : The Title List is simply a list of titles
Note
on a disc. If a title is deleted, that
title cannot be played again.
Playlist (DVD-RAM/-RW(VR)) :
A playlist is a custom-made list of titles.
When one playlist is played, only the titles
within the playlist will play and then stop.
Even if that playlist is deleted, the original
recording will not be deleted.
➝ X2 ➝ X4 ➝ X8
• You can scan the program in reverse order.
To return to normal speed playback, press the
√ll button.
No sound is heard during Scan(Search) mode,
Note
except on CDs (CD-DA). (You can hear the
sound during forward search (Fast 1) in disc.)
Depending on the disc type, the sound quality
may lower during Fast 1 mode.
Skipping Chapters or Tracks
During the playback, press the lœœ or √√l button
on the remote control.
• If you press the lœœ button
If you press the lœœ button, it moves to the beginning of the chapter, track or marker(DVD-RAM,
DVD-RW(VR mode) ). Pressing the button once
again within 3 seconds returns to the beginning of
the previous chapter, track or marker(DVD-RAM,
DVD-RW(VR mode) ).
• If you press the √√l button
If you press the √√l button, it moves to the next
chapter, track or marker(DVD-RAM,DVD-RW
(VR mode) )
Skipping ahead 30 seconds
During the playback, press F.ADV/SKIP button to
skip ahead exactly 30 seconds.
English - 45
Playback
Press the TITLE MENU button to move to the title
menu of the disc.
• Use this button if the disc contains more than one
title. Some discs may not support the title menu
functionality.
AUDIO CD(CD-DA)
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:2 PM
Page 46
Slow Motion Play/
Step Motion Play
About ANYKEY
Slow Motion Play (DVD-VIDEO / DVD-RAM
/ DVD±RW / DVD±R)
The ANYKEY functions allows you to easily search for
a desired scene by accessing title, chapter or time.
You can also change the subtitle and audio settings and
set some features including Repeat, Angle and Zoom.
During pause mode, press the SEARCH œœ or √√
button on the remote control for more than 1 second.
Moving to a scene directly using
the ANYKEY
• Each time you press the √√ button :
l √ Slow 1 ➝ l √ Slow 2 ➝ l √ Slow 3
• If you want to move to a title or a chapter to find a
desired scene.
• Each time you press the œœ button :
œl Slow 1 ➝ œl Slow 2 ➝ œl Slow 3
Playback
To return to normal speed playback, press the
√ll button.
Step Motion Play (DVD-VIDEO / DVD-RAM
/ DVD±RW / DVD±R)
1
Press the ANYKEY button during playback.
2
Press the …† buttons to select Title, Chapter.
DVD-VIDEO
During pause mode, press the F.ADV button on the
remote control.
• Each time the button is pressed, a new frame will
appear.
Title
1/2
Chapter
1/28
Time
Subtitle
00:00:01
ENG
Audio
ENG
Repeat
Angle
Off
1/1
Zoom
Off
MOVE
D 5.1CH
CHANGE
To return to normal speed playback, press the
√ll button.
No sound is heard during Step or Slow mode.
Note
46 - English
3
Press the œ √ buttons or number (0~9) buttons to
select the desired scene.
Then, press the ENTER button.
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:3 PM
Page 47
• If you want to move to a desired time to help you find
a scene.
1
Press the ANYKEY button during playback.
2
Press the …† buttons to select Time.
3
Select repeat mode using œ √ button.
Press the ENTER button.
• To make the screen disappear, press the
ANYKEY or RETURN button.
DVD-RAM/DVD-RW(VR mode), unfinalized
Note
DVD±R and unfinalized DVD-RW (Video
mode) do not repeat a chapter.
DVD-VIDEO
Title
1/2
Chapter
1/28
Time
Subtitle
00:00:01
ENG
Audio
ENG
Repeat
Angle
Off
1/1
Zoom
Off
MOVE
D 5.1CH
0~9 NUMBER
Enter the time in the sequence of hours, minutes,
and seconds using the number buttons, then
press the ENTER button.
3
This may not work for some discs. When an
Note
Playing a Certain section Repeatedly
(A-B Repeat Playback)
1
Press the ANYKEY button during playback.
2
Press the …† buttons to select Repeat.
DVD-VIDEO
Repeat Playback
Title
1/2
Chapter
1/28
Time
Subtitle
00:00:01
ENG
Audio
ENG
Repeat
Angle
Off
1/1
Zoom
Off
MOVE
D 5.1CH
Playback
Audio CD(CD-DA) or an MP3 disc is inserted,
depending on the disc type, the information
display may not be appear.
The Time Search function does not operate in
some discs.
To make the screen disappear, press the
ANYKEY button again.
CHANGE
3
Press the œ √ button to select A-B, then press the
ENTER button.
4
Press the ENTER button at the point where you want
repeat play to start (A) and press it again at the point
where you want the repeat play to stop (B).
Repeat playback of the A-B section starts.
Playing Repeatedly(Repeat Playback)
Repeat A-B
1
Press the ANYKEY button during playback.
2
Press the …† buttons to select Repeat.
A-B
- To return to normal playback DVD-VIDEO
Title
1/2
Chapter
1/28
Time
Subtitle
00:00:01
ENG
Audio
ENG
Repeat
Angle
Off
1/1
Zoom
Off
MOVE
5
Press the CANCEL button to return to normal
playback.
D 5.1CH
If you set point (B) before five seconds has
CHANGE
Note
lapsed, the prohibition mark (
) will appear.
CDs do not support the Repeat A-B function.
English - 47
00995J(00)_VR330_AFS-Eng1
2006.4.13
7:3 PM
Page 48
Selecting the Subtitle &
Audio Language
Selecting the Audio language
Audio languages may not work depending on the
disc type. This is only available during playback.
Using the AUDIO button
Selecting the SUBTITLE language
Subtitle languages may not work depending on the
disc type. This is only available during playback.
1
Press the AUDIO button during playback.
Audio
ENG Dolby Digital 5.1CH
Using the SUBTITLE button
1
Press the SUBTITLE button during playback.
Subtitle
ENG
Playback
2
2
Press the …† buttons to select the desired subtitle language.
• To make the screen disappear, then press the
CANCEL or RETURN button.
Using the ANYKEY button
1
Press the ANYKEY button during playback.
2
Press the …† buttons to select Subtitle, then
press the œ √ buttons to select the desired subtitle language.
Press the AUDIO or …† buttons to select the
desired audio language.
Using the ANYKEY button
1
Press the ANYKEY button during playback.
2
Press the …† buttons to select Audio, then press
the œ √ buttons to select the desired audio language.
DVD-VIDEO
DVD-VIDEO
1/2
Chapter
1/28
Time
00:00:01
Subtitle
ENG
Audio
ENG
Repeat
Angle
Off
1/1
Zoom
Off
MOVE
Title
1/2
Chapter
1/28
Time
Subtitle
00:00:01
ENG
Audio
ENG
Repeat
Angle
Off
1/1
Zoom
Off
MOVE
Title
D 5.1CH
CHANGE
D 5.1CH
Audio languages may be different because
CHANGE
Note
they are disc-specific.
Some discs allow you to select the audio
language for the disc menu only.
The subtitle display may be different dependNote
ing on the disc type.
If the subtitles overlap, disable the caption
function on your TV.
Some discs allow you to select the language
for the disc menu only.
48 - English
00995J(00)_VR330_AFS-Eng2
2006.4.13
7:4 PM
Page 49
Changing the Camera
Angle
Zooming-In
If a DVD-VIDEO contains multiple angles of a particular
scene, you can use the Angle function. If the disc contains multiple angles, ANGLE appears on the screen.
1
DVD-VIDEO
Using the ANGLE button
1
Press the ANYKEY button during playback.
Press the ANGLE button, during playback.
Title
1/2
Chapter
1/28
Time
Subtitle
00:00:01
ENG
Audio
ENG
Repeat
Angle
Off
1/1
Zoom
Off
MOVE
Angle
2
D 5.1CH
CHANGE
1/3
Press the …† button to select the desired angle.
Press the …† buttons to select Zoom, then press
the ENTER button. ( ) will be displayed.
3
Press …†, œ √ buttons to move to the area you
want to enlarge.
4
Press the ENTER button.
Each time the ENTER button is pressed, the picture
is enlarged up to 4X (four times the normal size).
Playback
2
Using the ANYKEY button
1
Press the ANYKEY button during playback.
2
Press the …† buttons to select Angle, then press
the œ √ buttons or number (0~9) buttons to select
the desired angle scene.
DVD-VIDEO
Title
1/2
Chapter
1/28
Time
Subtitle
00:00:01
ENG
Audio
ENG
Repeat
Angle
Off
1/1
Zoom
Off
MOVE
D 5.1CH
CHANGE
This function is disc-dependent, and may not
Note
work all DVDs.
This function does not work when a DVD has not
been recorded with a multi-camera angle system.
DVD-VIDEO/
DVD-RAM/DVD±RW/
DVD±R
normal size ➝ 2X ➝ 4X ➝ 2X
➝ normal size
You can also select Zoom function directly
Note
using ZOOM button on the remote control.
English - 49
00995J(00)_VR330_AFS-Eng2
2006.4.13
7:4 PM
Page 50
Using the Bookmarks
Playing back a Bookmark
1
Press the MARKER button.
2
Press the œ √ buttons to select a bookmarked
scene.
(V mode)
Bookmark
1 2 - - - - - - - --
Set marks at scenes you want to see again so that you
can start playback from the marked position.
1
Press the MARKER button during playback.
MOVE
Bookmark
3
Playback
MOVE
2
SELECT
1
Press the MARKER button.
2
Press the œ √ buttons to select a bookmarked
scene.
1 - - - - - - - - --
PLAY
CANCEL
1 2 - - - - - - - --
RETURN
MOVE
3
Press the œ √ button to move to the next position.
4
Press the ENTER button again when the desired
scene appears.
• The number 2 is displayed and the scene is
memorized. Repeat above to bookmark other
positions. You can bookmark up to 10 scenes.
3
Bookmark
RETURN
Press the ENTER or √ll button to start playing
from the selected scene.
Bookmark
MOVE
CANCEL
Clearing a Bookmark
RETURN
Press the ENTER button when the desired scene
appears.
• The number 1 is displayed and the scene is
memorized.
Bookmark
PLAY
- - - - - - - - - --
PLAY
CANCEL
RETURN
Press the CANCEL button to delete the selected
bookmark.
Bookmark
1 - - - - - - - - --
1 2 - - - - - - - --
MOVE
SELECT
RETURN
When the disc tray is opened and then
MOVE
50 - English
PLAY
CANCEL
RETURN
Note
closed, bookmarks will disappear.
00995J(00)_VR330_AFS-Eng2
2006.4.13
7:4 PM
Page 51
Playing back a Marker
Using the Markers
1
Press the MARKER button during playback.
2
Press the œ √ buttons to select a marked scene.
(VR mode)
Marker
1
Press the MARKER button during playback.
Marker
-- -- -- -- -- -- -- -- -- --
N:0
MOVE
SELECT
2
01 02 - - - - - - - -- N : 2
RETURN
3
Press the ENTER button when the desired scene
appears.
Marker
01 - - - - - - - - -- N : 1
PLAY
CANCEL
RETURN
Press the ENTER or √ll button to start playing
from the selected scene.
• If you press the NEXT SKIP (√√l )button or the
PREVIOUS SKIP(lœœ)button in marker mode,
and the next or current marked point plays for
shorter than three seconds, playback starts from
the previous marked point.
MOVE
PLAY
CANCEL
RETURN
• The number 01 is displayed and the scene is
memorized.
3
4
Press the œ √ button to move to the next position.
Press the ENTER button again when the desired
scene appears.
Marker
MOVE
1
Press the MARKER button during playback.
2
Press the œ √ buttons to select a marked scene.
Press the CANCEL button to delete the selected
mark.
Marker
01 02 03 04 05 06 07 08 09 10 √ N : 10
Marker
01 02 03 04 05 06 07 08 09 --
01 02 - - - - - - - -- N : 2
PLAY
CANCEL
N:9
RETURN
• The number 02 is displayed and the scene is
memorized.
• DVD-RAM or DVD-RW (VR Mode) discs have
the Marker function instead of the Bookmark
function. The Marker function allows you to mark
up to 99 scenes. Since the scenes may be displayed as many different pages, numbering is
necessary. If a disc in use is encoded with Disc
Protect, Markers cannot be set or deleted. Only
playback is available.
MOVE
PLAY
CANCEL
RETURN
• When a marker is cleared while DVD-RAM/
DVD-RW(VR mode) is playing, marker numbers
will change. For example, if the 7th marker is
cleared after ten markers are registered, the
marker numbers after the eighth will automatically move ahead by one and the 8th marker
becomes the 7th.
English - 51
Playback
Clearing a Marker
00995J(00)_VR330_AFS-Eng2
2006.4.13
7:4 PM
Page 52
Playing back an Audio
CD (CD-DA)
Buttons on the Remote Control used
for CD playback
Each disc has a variety of menu functions available.
Playing an Audio CD (CD-DA)
Insert an Audio CD (CD-DA) into the disc tray.
• The Audio CD menu appears and the tracks
(songs) are played automatically.
1
CD
1
2
3
3
4
5
Music List
TRACK 1
√ 0:00:15
TRACK 1
CDDA
PLAY MODE
6
01/15
No.
Title
TRACK 1
00:03:50
002
003
004
005
006
007
TRACK 2
TRACK 3
TRACK 4
TRACK 5
TRACK 6
TRACK 7
00:04:00
00:03:49
00:03:47
00:04:29
00:03:44
00:03:44
MOVE
ENTER
Length
RETURN
7
6
EXIT
Playback
8
2
Press the …† buttons to select the track (song) to
start playback from, and then press the ENTER
button.
Audio CD(CD-DA) Screen Elements
!
CD
@
Music List
TRACK 1
01/15
No.
$
√ 0:00:15
TRACK 1
CDDA
PLAY MODE
002
003
004
005
006
007
MOVE
Title
Length
TRACK 1
00:03:50
TRACK 2
TRACK 3
TRACK 4
TRACK 5
TRACK 6
TRACK 7
00:04:00
00:03:49
00:03:47
00:04:29
00:03:44
00:03:44
ENTER
RETURN
EXIT
#
%
^
1. Play mode icon.
2. Current track (song): Displays the number of the track
currently being played.
3. Displays the current play index and total track number.
4. This shows the operating state of a disc and a playback
time corresponding to a portion that is currently played.
5. Displays the track list (song list) and the playing time of
each track.
6. Button display
52 - English
1. lœœ button: Returns to the beginning of the current
track when pressed during playback. If pressed
again, your DVD Recorder & VCR moves to and
plays the previous track.
If you press this button within three seconds after
playback starts, the previous track will be played.
If you press this button after three seconds, the
current track will be replayed from the beginning.
2. √√l button: Plays the next track.
œœ /√
√√) button: Fast Play (X2, X4, X8)
3. Press the (œ
4. ■ : Stops a track(song).
5. √ll : Plays a track(song) or pauses playback.
6. …†: Selects a track (song).
7. √, ENTER button: Plays the selected track (song).
8. ANYKEY : To display the play mode window.
(Repeat or Play Option).
00995J(00)_VR330_AFS-Eng2
2006.4.13
7:4 PM
Page 53
Playing back an MP3
Disc
Buttons on the Remote Control
used for MP3 disc playback
Playing an MP3 Disc
Insert an MP3 disc into the disc tray.
1
DVD-Recorder
1
2
3
4
Disc Navigation
MP3
Disc
Navigation
Photo
√
Timer Rec.
Music
√
Setup
5
6
MOVE
ENTER
RETURN
EXIT
7
4
Press the …† buttons to select the track (song) you
want to hear, and then press the ENTER button.
Press the …† buttons to select the Music, and then
press the ENTER or √ button.
MP3
8
Music List
SONG01
√ 0:00:15
SONG01
3.5MB
2006/01/01
MP3
PLAY MODE
01/11
No.
Title
002
ROOT
SONG01
SONG02
003
004
005
006
SONG03
SONG04
SONG05
SONG06
MOVE
ENTER
RETURN
EXIT
MP3 Screen Elements
!
MP3
@
6
Music List
SONG01
$
√ 0:00:15
&
SONG01
3.5MB
2006/01/01
MP3
PLAY MODE
01/11
No.
Title
002
ROOT
SONG01
SONG02
003
004
005
006
SONG03
SONG04
SONG05
SONG06
MOVE
ENTER
#
%
RETURN
EXIT
^
1. lœœ button: Returns to the beginning of the current
track when pressed during playback. If pressed
again, your DVD Recorder & VCR moves to and
plays the previous track.
If you press this button within three seconds after
playback starts, the previous track will be played.
If you press this button after three seconds, the
current track will be replayed from the beginning.
2. √√l button: Plays the next track.
3. ■ : Stops a track(song).
4. √ll : Plays a track(song) or pauses playback.
5. RETURN button: Moves to the folder to which the
current song belongs.
6. …† : Selects a track (song).
7. √, ENTER button: Plays the selected track (song) or
displays the files in the selected folder.
8. ANYKEY : To display the play mode window.
(Repeat or Play Option).
1. Play mode icon.
2. Current track (song): Displays the name of the track
being played.
3. Displays the current play index and total file number.
4. This shows the operating state of a disc and a playback
time corresponding to a portion that is currently played.
5. Displays the mp3 file and folder list (song list).
6. Button display.
7. MP3 file information
English - 53
Playback
2
3
Press the …† buttons to select the Disc Navigation,
and then press the ENTER or √ button.
00995J(00)_VR330_AFS-Eng2
2006.4.13
7:4 PM
Page 54
Repeat Playback of an
Audio/MP3 Disc
1
During playback, press the ANYKEY button.
The Repeat mode will be highlighted.
Play Option Mode
1
During Stop, Press the ANYKEY button.
The Play option will be highlighted.
CD
Music List
TRACK 1
01/15
No.
CD
Music List
TRACK 1
01/15
No.
√ 0:00:01
TRACK 1
CDDA
PLAY MODE
001 MODE
TRACK 1
PLAY
002
TRACK 2
Repeat : Off
003
TRACK 3
Play option
004 : Normal
TRACK 4
005
TRACK 5
006
TRACK 6
007
TRACK 7
MOVE
ENTER
Length
√ 0:00:01
00:03:50
00:04:00
TRACK 1
CDDA
00:03:49
00:03:47
00:04:29
00:03:44
00:03:44
RETURN
PLAY MODE
001 MODE
TRACK 1
PLAY
002
TRACK 2
Repeat : Off
003
TRACK 3
Play option
004 : Normal
TRACK 4
005
TRACK 5
006
TRACK 6
007
TRACK 7
MOVE
2
Title
001 MODE
TRACK 1
PLAY
002
TRACK 2
Repeat : Off
003
TRACK 3
004
TRACK 4
•
•
•
00:03:50
00:04:00
00:03:49
Repeat Track (CD (CD-DA)/MP3)
Repeat Folder (MP3)
Repeat Disc (CD (CD-DA)/MP3)
Press the CANCEL button to return to normal
playback.
54 - English
√ 0:00:01
TRACK 1
Length
- To return to normal playback -
3
EXIT
Music List
TRACK 1
01/15
No.
00:03:49
00:03:47
00:04:29
00:03:44
00:03:44
RETURN
CD
Music List
TRACK 1
ENTER
00:03:50
00:04:00
Press the œ √ buttons to select a desired Play
Option, then press the ENTER button.
01/15
No.
CD
Length
EXIT
Press the œ √ buttons to select the desired repeat
mode you want to play repeatedly, then press the
ENTER button.
Playback
2
Title
Title
CDDA
Title
001 MODE
TRACK 1
PLAY
002
TRACK 2
Repeat : Off
003
TRACK 3
Play option
004 : Normal
TRACK 4
005
TRACK 5
Length
00:03:50
00:04:00
00:03:49
00:03:47
00:04:29
• Normal: Tracks on a disc are played in the
order in which they were recorded on the disc.
• Playlist: The Playlist playback option allows you to
select the order in which you want tracks to play.
• Intro[ I ]: The first 10 seconds of each track will be
played. If you want to listen to the music that you
have selected, press the ENTER button or √ll button. The play option will be changed to Normal Play.
When Intro Play is completed, Normal Play is performed.
• Random[ R ]: The Random option plays a disc’s
tracks in random order. After a random list is generated and played completely, another random list is
generated and played.
Random Play is continued until the play option is
changed.
00995J(00)_VR330_AFS-Eng2
2006.4.13
7:4 PM
Page 55
To Program Tracks
Playing a Picture Disc
You can register a maximum 30 tracks in the playlist.
1
In still mode, press the ANYKEY button.
The Play option will be highlighted.
2
Press the œ √ buttons to select Playlist, then
press the ENTER button.
Playlist screen is displayed.
1
Insert a JPEG into the disc tray.
DVD-Recorder
Disc Navigation
JPEG
Disc
Navigation
Photo
√
Timer Rec.
Music
√
Setup
CD
Playlist
01/15
CDDA
TRACK 1
CDDA
TRACK 2
CDDA
TRACK 3
CDDA
TRACK 4
CDDA
TRACK 5
CDDA
TRACK 6
CDDA
TRACK 7
CDDA
TRACK 8
PLAY MODE
MOVE
ENTER
EXIT
Press the …† buttons to select tracks in the order
in which you want them to play, then press the
ENTER button.
CD
04/15
TRACK 1
001
TRACK 1
CDDA
TRACK 2
002
TRACK 2
CDDA
TRACK 3
003
TRACK 3
CDDA
TRACK 4
004
TRACK 4
CDDA
TRACK 5
CDDA
TRACK 6
CDDA
TRACK 7
CDDA
EXIT
Press the …† buttons to select Disc Navigation,
and then press the ENTER or √ button.
3
Press the …† buttons to select Photo, and then
press the ENTER or √ button.
4
Press the …† œ √ buttons to select a picture.
JPEG
Photo List
01/10
JPEG01
TRACK 8
PLAY MODE
4
RETURN
2
Playlist
CDDA
ENTER
MOVE
ENTER
EXIT
If you selected a wrong track, press the √ button,
then press the …† buttons to select the wrong
track. Press the CANCEL button. The wrong track
will be removed.
ROOT
JPEG01
JPEG02
JPEG03
JPEG04
JPEG05
JPEG06
JPEG07
Slide Show
MOVE
ENTER
RETURN
EXIT
• To see the next 8 pictures, press the √√l button.
• To see the previous 8 pictures, press the lœœ button.
CD
Playlist
03/03
CDDA
TRACK 1
001
TRACK 1
CDDA
TRACK 2
002
TRACK 2
CDDA
TRACK 3
003
TRACK 3
CDDA
TRACK 4
CDDA
TRACK 5
CDDA
TRACK 6
CDDA
TRACK 7
CDDA
TRACK 8
PLAY MODE
5
MOVE
ENTER
CANCEL
EXIT
Press the PLAY button to play the playlist.
English - 55
Playback
3
MOVE
00995J(00)_VR330_AFS-Eng2
5-1
2006.4.13
7:4 PM
Page 56
If you press the √ll button, the Slide Show
Speed screen will appear.
Press the œ √ buttons to set the slide show
speed, then press the ENTER button.
Playing the VCR
DVD-RW(VR)
Slide Show Speed
Slow
Normal
Fast
JPEG01
MOVE
-2
5
PHOTO
ENTER
1
Insert a standard VHS tape into the VCR deck.
• When a tape is inserted, power will turn on automatically.
2
Press the √II(PLAY/PAUSE) button on the
remote control or on the front panel of the unit.
The videotape will begin to play automatically if
the Record Safety Tab is removed and Auto Play
is turned on.
RETURN
Press the ENTER button with a picture selected
in the Album screen and select a display mode
(Album screen (
), Slide show (
),
Rotation (
) or Zoom (
)) using the œ √
buttons, then press the ENTER button.
DVD-RW(VR)
Record Safety Tab
Playback
JPEG01
MOVE
PHOTO
ENTER
RETURN
: Returns to the Album screen.
: The unit enters slide show mode.
Before the slide show can begin, the picture
interval (Slide show speed) must be set.
: Each time the ENTER button is pressed, the
picture rotates 90 degrees clockwise.
: Each time the ENTER button is pressed, the
picture is enlarged up to 4X(four times the
normal size).
3
Press the (STOP) button on the remote control
or on the front panel of the unit.
Tracking
➝ normal size ➝ 2X ➝ 4X ➝ 2X
• Press the ANYKEY button to display menu bar.
• Press the RETURN button to clear the menu bar.
The Tracking adjustment removes the white lines that
sometimes appear during playback because of slight
differences in recording decks. The CH/TRK ( / )
button will automatically align the recorded tracks with
the playback heads to solve this problem. You may also
set tracking manually.
1
56 - English
Adjust Tracking Manually During playback, press
the CH/TRK ( / ) buttons to remove white lines
from the picture.
00995J(00)_VR330_AFS-Eng2
2006.4.13
7:4 PM
Page 57
Special VCR Playback
Features
While a videotape is playing, you can enjoy a variety of
special playback features, including Still, Frame Advance,
Skip, Slow motion, and more.
Pause
In Play mode, press √II(PLAY/PAUSE)button to still
a single frame.
Frame Advance
Variable Search
System
Each time you record a cassette on this DVD Recorder
& VCR, an “index” is automatically marked on the tape
when recording is started. The Search function allows
you to fast-forward or rewind to a specific index and
start playback from that point. Depending on the direction selected, the indexes are numbered as follows
• This DVD Recorder & VCR uses a standard indexing
system (VISS). As a result, it will recognize any indexes marked by other VCRs using the same system and
vice versa.
In Pause mode, press F.ADV/SKIP button to
advance to the next frame.
Go To Zero
Use this feature when you want to search for the
0:00:00 counter position on a cassette.
Fps/Review
1
Press the CANCEL button at the point on the tape
where you want to set the counter to 0:00:00.
2
While a cassette is stopped, press the ANYKEY
button.
Skip
VCR
Go To Zero
End Search
In Play mode, press F.ADV/SKIP button to cue
ahead exactly 30 seconds. Press F.ADV/SKIP button
repeatedly up to 4 times to cue ahead 2 minutes.
Forward Intro Scan
Reverse Intro Scan
MOVE
SELECT
Slow motion
In Pause mode, press √√ button for slow motion.
Press the √√ button repeatedly to vary slow motion
speed from 1/5 to 1/30 of normal playback. Press
the PLAY button twice to resume normal viewing.
S-VHS Playback
3
Press the …† buttons to select Go To Zero, then
press the ENTER button.
The VCR will rewind or fast forward, searching for
the 0:00:00 counter position, and then automatically stop at that position.
Go To Zero
➛➛
The DVD Recorder & VCR allows you to playback high
quality S-VHS tapes.
1
Insert an S-VHS tape into the VCR deck.
2
Press √II (PLAY/PAUSE) button on the remote
control or on the front panel to play a S-VHS tape.
00:00:49
English - 57
Playback
In Play mode, press Forward (√√)button or Rewind
(œœ)button to Fps/review at two speeds:
• Picture Search - Press and release repeatedly to
advance the tape forward or backward at 2,3,5,7
times normal speed.
• Jet Search - Press and hold to advance the tape
forward or backward at 7 times normal speed.
00995J(00)_VR330_AFS-Eng2
2006.4.13
7:4 PM
Page 58
2
End Search
Use this feature when you want to search for a blank
position to record a program on a cassette.
While a cassette is stopped, press the ANYKEY
button.
1
VCR
Go To Zero
End Search
Scan and Play
❿❿
00:01:49
Forward Intro Scan
Reverse Intro Scan
MOVE
SELECT
Press the …† buttons to select End Search, then
press the ENTER button.
The VCR will fast forward, searching for a blank
position, and then automatically stop at that position. If the VCR reaches the end of the tape during
end search, the tape will be ejected.
Playback
2
End Search
❿❿
00:00:13
Forward / Reverse Intro Scan
Use scan and play when you don’t know exactly
where a program is located on a cassette tape.
1
Press the …† buttons to select Forward Intro
Scan or Reverse Intro Scan, then press the
ENTER button. When an Index mark is found, the
DVD Recorder & VCR will playback the tape for 5
seconds, after which it will continue searching for
the next Index mark.
While a cassette is stopped, press the ANYKEY
button.
VCR
Go To Zero
End Search
Forward Intro Scan
Reverse Intro Scan
MOVE
58 - English
SELECT
00995J(00)_VR330_AFS-Eng2
2006.4.13
7:4 PM
Page 59
Recording
Before Recording
This unit can record on various types of discs. Before
recording, read the following instructions and select the
disc type according to your preference.
Recordable discs
This recorder can record on the following discs.
This section explains various DVD recording
methods.
DVD-RAM
DVD-RW
DVD-R
DVD+RW
DVD+R
• DVD±RWs and DVD-RAMs are rewritable.
• DVD±Rs are non-rewritable.
Compatibility between Samsung and
other manufacturer's Recorders.
Disc Types
Recording
format
DVD-RAM
VR Mode
VR Mode
DVD-RW
V Mode
Recordable discs ...............................................................59
Recording Formats ...........................................................60
DVD-R
V Mode
DVD+RW
-
DVD+R
-
Recording Mode................................................................60
Unrecordable video ..........................................................60
Recording the Current Channel you are watching ...........61
Recording from External Devices ......................................62
Recording through a DV Input jack...................................62
Making a One Touch Recording(OTR) ..............................63
Making a Timer Recording ................................................63
■
Editing the Scheduled Record List .....................................65
Deleting a the Scheduled Record List................................65
VCR Recording
Basic VCR Recording.........................................................66
Check Remaining Time ....................................................67
Special Recording Features ..............................................67
Copy to DVD or VCR........................................................68
Note
■
Finalize
- This closes the DVD-RW/±R so no additional
recording can be done.
Unfinalize
- This allows additional recording on a DVD-RW disc
originally recorded on the DVD-VR330, VR330S.
- A DVD-RW disc that has been recorded by
DAO(Disc At Once) in a PC cannot be unfinalized.
- A DVD-RW disc that has been recorded in Video
Mode of a different maker’s recorder cannot be
unfinalized.
- A DVD±R disc cannot be unfinalized.
English - 59
Recording
DVD Recording
Before Recording ...............................................................59
Recording Device Finalizing Additional Recording
in Samsung Recorder
Samsung
X
Recordable
Recordable
Other Company
X
Not
recordable
finalized
Samsung
Recordable
not finalized
finalized
Not recordable
Other Company
not finalized
Recordable
finalized
Not
recordable
Samsung
not finalized
Recordable
Not recordable
finalized
Other Company
not finalized Not recordable
finalized
Not recordable
Samsung
not finalized
Recordable
finalized
Not recordable
Other Company
not finalized Not recordable
Samsung
Recordable
X
Not recordable in some cases
Other Company
X
finalized
Not recordable
Samsung
not finalized
Recordable
finalized
Not recordable
Other Company
not finalized Not recordable in some cases
00995J(00)_VR330_AFS-Eng2
2006.4.13
7:4 PM
Page 60
Recording Formats
DVD+RW/+R
When you insert an unused disc, the following message
appears. Since available functions differ depending on
the disc type, select a disc that best fits your preferences.
DVD-RAM: Use after formatting the disc.
• You can also make your own chapters on DVD+RWs
and edit them using the Chapter Edit menu.
(see pages 76 to 78)
Recording Mode
Unformatted Disc
Do you want to format this disc?
Yes
NO
DVD±RW/+R: When an unused DVD±RW/+R disc is
first inserted, the message “Uninitialized
Disc Do you want to initialize this disc?”
will be displayed. If you select Yes, initializing will be start.
With the unit in Stop mode, select one of four recording
modes by pressing the REC SPEED button repeatedly
for the desired recording time and picture quality.
In general, picture quality improves as the recording
time decreases.
In AUTO mode, the most suitable record mode is
adjusted automatically, according to remaining time on
the disc and length of the timer recording.
You can select only one mode from XP, SP, LP and EP
for timer recording.
Mode
Characteristic
Approx. 2 hours
about 4 Mbps
LP
(long recording mode)
Select when the
video quality is
important.
Select to record in
standard quality.
Select when a long
recording time is
required.
EP
(extended mode)
Select when a long
recording time is
required.
Approx. 6 hours/
about 1.2 Mbps
Approx. 8 hours/
about 0.8 Mbps
AUTO
for timer recording
only see page 64.
Approx 60 to 480 Min
approx 0.8 to 8 Mbps
XP
(high quality mode)
Uninitalized Disc
SP
(standard quality mode)
Do you want to initialize this disc?
Yes
NO
Recording
When using a DVD-RW disc, you can change
the mode. Refer to Formatting a Disc on
page 87.
DVD-Recorder
Disc Manager
Recording Times
Data Rates
Approx. 1 hour
about 8 Mbps
Approx. 4 hours
about 2 Mbps
DVD-RW(VR)
Title List
Disc Name
:
√
Playlist
Disc Protection
: Not Protected
√
Disc Format
: DVD-VR
Disc Manager
Choose
theFinalize
recording format for DVD-RW
Disc
√
Delete All Title Lists
√
Timer Rec.
Setup
DVD-VR
DVD-V
ENTER
RETURN
√
Copy
MOVE
EXIT
DVD-R: Initializing disc is unnecessary.
DVD-RW(Video mode)/-R
- The dual layer DVD±Rs have approximately double
the capacity of single layer DVD±Rs. (See page 43.)
Unrecordable video
Pictures with copy protection cannot be recorded on this
DVD Recorder & VCR.
When the DVD Recorder & VCR receives a copy guard
signal while recording, recording stops and the following
message appears on the screen.
• Chapters will be created automatically when you
finalize recording on DVD-R/DVD-RW discs in Video
mode.
• Simple editing (erasing titles/changing title name).
DVD-RAM/-RW(VR mode)
• This mode involves multiple editing functions (such as
deletion of the whole title, partial deletion of a title,
etc.).
• Various editing options using a created Playlist.
60 - English
You cannot record copy protected movie.
00995J(00)_VR330_AFS-Eng2
2006.4.13
7:4 PM
Page 61
Concerning Copy Control Signals
TV broadcasts that contain copy control signals may have
one of the following three signal types, Copy-Free, CopyOnce and Copy-Never. If you want to record a copy-once
type program, use DVD-RW with CPRM in VR Mode or
DVD-RAM discs.
DVD-RW(Ver.1.1)
DVD-RW(Ver.1.1)
with CPRM
VR mode
DVD-R
DVD-RAM(Ver.2.0)
DVD+R
DVD+RW
Copy-Free
O
Copy-Once
-
Copy-Never
-
O
O
O
O
O
O*
O*
-
-
3
Press the CH/TRK ( / ) buttons or number
buttons to select the channel you want to record.
4
Press the REC SPEED button repeatedly, to select the
recording speed (quality).
• XP(High, approx. 1 hour) ➝ SP(Standard,
approx. 2 hours) ➝ LP(Low, approx. 4 hours)
➝ EP(Extended Play, approx. 6 hours/8hours)
-RW
VR
XP
CH6
Recordable Time 00:26
Once “Copy Once” has been recorded, additional recording
cannot be performed.
* compatible with CPRM.
- Content Protection for Recordable Media (CPRM)
CPRM is a mechanism that ties a recording to the
media on which it is recorded. It is supported by some
DVD recorders, but not by many DVD players. Each
blank recordable DVD has a unique 64-bit media ID
etched in the BCA(Burst Cutting Area). When protected
content is recorded onto the disc, it can be encrypted
with a 56-bit C2 (Cryptomeria) cipher derived from the
media ID. During playback, the ID is read from the BCA
and used to generate a key to decrypt the contents of
the disc. If the contents of the disc are copied to other
media, the ID will be absent or wrong and the data will
not be decryptable.
1. Check to make sure the antenna cable is connected.
2. Check the remaining time on the disc.
DVD-RAM/DVD±RW/+R discs should be formatted or
initialized in advance before beginning recording.
(See page 59.)
1
Press the OPEN/CLOSE button and place a
recordable disc on the disc tray.
2
Press the OPEN/CLOSE button to close the disc
tray.
Wait until “LOAD” disappears from the front panel
display.
Press the REC button.
• “” is displayed on the screen and recording
begins.
6
Press the STOP button to stop or finish a recording
in progress.
• The message “Updating the information of disc.
Please wait for a moment” is displayed.
Pausing / Resuming
• Press the REC PAUSE button to pause a recording
in progress.
• Press the REC PAUSE button again during pause to
resume recording.
• You can switch channels by pressing the CH/TRK
( / ) buttons while recording pauses.
Recording will stop automatically if there is
Note
no free space left for recording.
Up to 99 titles can be recorded onto a DVD-
RAM/-RW/-R disc, and up to 48 titles onto a
DVD+RW/+R disc.
If the power is interrupted due to power fail-
ure or other reasons, the title being recorded
will not be saved onto the disc.
Recording will stop automatically if a copy
protected image is selected.
Do not use DVD-R authoring discs with this
unit.
English - 61
Recording
Recording the Current
Channel you are watching
5
00995J(00)_VR330_AFS-Eng2
2006.4.13
7:4 PM
Page 62
Recording from
External Devices
Follow these directions to record onto a disc or a tape
from External Devices such as a Camcorder.
1
Connect the AV out jack of your External Device to
the AV IN jack on the front or rear of your DVD
Recorder & VCR using the Audio/Video Cable.
2
Power on your DVD Recorder & VCR and switch
to AV In mode by pressing the INPUT SEL. button
on the remote control.
The front panel display changes in the following
sequence depending on the Video input setting in
the menu.
AV1: ➝ Channel Number ➝ AV 1 ➝ AV 2➝ DV
Recording through the
DV Input jack
You may control your Camcorder using the IEEE1394
(DV) interface.
Follow these directions to record onto a disc or tape
from a camcorder that has a DV output jack.
1
Connect the DV output jack of your camcorder to
the DV input jack on the front of your DVD
Recorder & VCR using a DV cable.
2
Power on your DVD Recorder & VCR and switch
to DV mode by pressing the INPUT SEL. on the
remote control.
3
Press the REC SPEED button repeatedly to select
the recording speed(quality).
➝ SP ➝ LP ➝ EP ➝ XP
S-Video: ➝ Channel Number ➝ SUPER ➝ AV 2➝ DV
3
Press the REC SPEED button repeatedly to select
the recording speed(quality).
4
If the input is set to DV, a playback/record menu that
enables camcorder control appears on the top of the
screen.
➝ SP ➝ LP ➝ EP ➝ XP
Recording
DV
4
When your DVD Recorder & VCR is in the Stop
mode, start playback on your external device.
5
Press the REC button on your DVD Recorder &
VCR to start recording when the desired video is
displayed from the external device.
6
Press the STOP button on your DVD Recorder &
VCR when the recording is finished.
Also refer to the user manual for your External
Note
Devices when recording through AV In jacks on
the DVD/VCR using Audio/Video cable.
You can record an external source through
S-Video cable. (see page 25).
For more information on changing the Video
Input from AV1 to S-Video, see page 39(Video
Input).
The DV device is connected.
MOVE
SELECT
RETURN
5
Select the Play icon on the upper part of the
screen to playback the camcorder and find the
starting position to copy.
6
To start recording, Press the œ √ button to select
rec(●) icon in the top side of the screen, then
press the ENTER button.
You can press the REC button on the remote control to start recording. To display playback related
icons on the screen, press either direction button
on the remote control.
7
Press the STOP button on your DVD Recorder &
VCR when the recording is finished.
Some camcorders may not work with your
Note
62 - English
DVD Recorder & VCR even if they have a DV
output jack.
Also refer to the user manual for your camcorder when recording through the DV jack.
00995J(00)_VR330_AFS-Eng2
2006.4.13
7:4 PM
Page 63
Making a One Touch
Recording (OTR)
One-Touch Recording (OTR) allows you to add
recording time in preset increments up to 4 hours by
pressing the REC button repeatedly.
Press the CH/TRK ( / ) buttons or number buttons to select the channel to record.
If you want to record through a connected external
component, press the INPUT SEL. button to
select an appropriate external input(AV1, AV2 or
DV).
• CATV channel: 1 to 125
1
Making a Timer
Recording
The clock (Setup – Clock Set) must be set before
proceeding with a timer recording. (See page 31)
1
Press the OPEN/CLOSE button, and place a
recordable disc on the disc tray.
2
Press the OPEN/CLOSE button to close the disc
tray.
Wait until “LOAD” disappears from the front panel
display.
3
With the unit in Stop mode, press the MENU
button.
4
Press the …† buttons to select Timer Rec., then
press the ENTER or √ button.
• TV channel: 2 to 69
2
Press the REC button to start recording.
3
While in Record mode, press the REC button
again to activate the One-Touch Recording (OTR).
• Record length 0:30 appears on the On-Screen
Display and the DVD Recorder & VCR will record
for exactly 30 minutes.
DVD-Recorder
Timer Record
DVD-RAM(VR)
Title List
Timer Record
√
Playlist
Scheduled Record List
√
4
Timer Rec.
Continue pressing REC button to add recording
time in preset increments up to 4hours.
Setup
Copy
MOVE
➝ 0:30 ➝ 1:00 ➝ 1:30 ➝ 2:00 ➝ 3:00 ➝ 4:00 ➝ Off
• The DVD Recorder & VCR stops recording
automatically when the time has elapsed.
To stop recording
Press the STOP () button.
The message “Press STOP button once more to
cancel Timer Record.” is displayed.
Press the STOP () button again.
The message “Updating the Information of disc.
Please wait for a moment.” is displayed.
The timer counter decreases by the minute
Note
5
ENTER
RETURN
EXIT
Press the …† buttons to select Timer Record,
then press the ENTER or √ button.
You can go to the Timer recording screen directly
by pressing the TIMER REC button.
The Timer Recording screen is displayed.
Scheduled Record List
DVD-Recorder
DVD-RAM(VR)
No.
To
Source
Current Time 1:05 AM
Date
Start
End Mode Edit
No. 01
To
Source
Date
DVD
CH06
01/01
Recordable Time
MOVE
Start
End
Mode
01:05 AM 03:05 AM SP
00:45 SP
ENTER
RETURN
EXIT
from 4:00 to 0:00, then the DVD Recorder
& VCR stops recording.
English - 63
Recording
Disc Manager
00995J(00)_VR330_AFS-Eng2
6
2006.4.13
7:4 PM
Page 64
Fill in the items using the …†œ √ buttons.
œ √ : Moves to the previous/next item,
…† or 0~9 : To set or change items in the
Scheduled Record List Menu.
• To : Select the media to record (DVD or VCR).
• Source : The video input source (AV 1, AV 2), or
the broadcasting channel you want to
make a timer recording from.
• Date: Date that the timer recording starts
- There are three options when setting the date.
see below:
! To make a recording on a specific date, press the
…† or number buttons until the date you want
appears.
No. 01
To
Source
Date
DVD
CH06
01/01
Recordable Time
Start
End
Mode
03:05 AM 05:05 AM SP
00:45 SP
When you are recording at EP mode on a
Note
DVD-RW(V)/-R disc, it may not record for the
full 6 or 8 hours because the unit uses the
VBR(Variable Bit Rate) ENCODING system.
For example, if you record a program with a lot
of action, it uses a higher bit rate which in turn
consumes more disc memory.
• Recording mode (VCR)
AUTO : Select when you want to set video quality
automatically. The auto quality depends on
remaining time of VCR tape.
SP : Standard Play, for best picture quality.
SLP : Super Long Play, for maximum recording time
(3 times SP).
@ To make a recording at the same time every day
(Mon-Fri), press the …† buttons until Mon-Fri
appears:
No. 01
To
Source
DVD
CH06
Recordable Time
Date
Start
End
Mode
Mon~Fri 03:05 AM 05:05 AM SP
00:45 SP
If the timer settings overlap
The programs are recorded in order of priority.
If timer recording is set for the first program and
then again for the second program and both
programs overlap, the following message will
appear on the screen: “This setting is identical with
1,2.” The message shows that the first program has
priority. After recording of the first program is
complete, the second program starts being
recorded.
# To make a recording on a specific day of the
week(Sun’s-Sat’s), press the …† buttons until
Sun’s….Sat’s appears:
No. 01
To
Source
Date
DVD
CH06
Sun’s
Recording
Recordable Time
Press the ENTER button.
•
will appear on the front panel. It means that a
timer recording is registered.
7
Start
End
Mode
03:05 AM 05:05 AM SP
00:45 SP
• Start/End Time : Start and end time of the timer
recording.
To exit without saving the current setting
• Recording mode (DVD)
Press the MENU or TIMER REC button.
AUTO : Select when you want to set video quality automatically. In AUTO mode, the most suitable
record mode is adjusted automatically, according to remaining time on the disc and length of
the timer recording.
You can selected only one mode from XP, SP,
LP and EP for timer recording.
To return to the previous menu
XP (high quality) : Select when audio and video qualities
are important. (Approx. 1 hour)
Press the RETURN button if you don’t want to set a
timer recording.
8
SP (standard quality) : Select to record in standard quality. (Approx. 2 hours)
LP (low quality) : Select when a long recording time is
required.(Approx. 4 hours)
EP (extended mode) : Select when a longer recording
time is required. (Approx.6 hours
at 1.2 Mbps or Approx.8 hours
at 0.8 Mbps )
64 - English
Turn the power off to finish the timer recording.
•
will blink if disc or tape is not inserted.
The timer recording time may differ from the set
Note
time depending on disc status and overall timer
recording status (for example, recording times
overlapping, or when the previous recording
ends within 3 minutes before the start time of
the next recording.)
00995J(00)_VR330_AFS-Eng2
2006.4.13
7:4 PM
Page 65
Editing the Scheduled
Record List
5
Press the …† button to select Edit, then press
the ENTER button.
• The Timer Recording screen is displayed.
Edit the items you want to modify. See the Timer
Recording section for more information on Timer
Recording Input items. (See page 64)
Scheduled Record List
DVD-Recorder
DVD-RAM(VR)
No.
To
Source
Current Time 1:07 AM
Date
Start
End Mode Edit
No. 01
Follow these directions to edit the timer record list.
To
Source
Date
DVD
CH06
01/01
Recordable Time
1
2
Press the MENU button.
MOVE
Press the …† button to select Timer Rec., then
press the ENTER or √ button.
DVD-Recorder
Timer Record
DVD-RAM(VR)
Title List
Timer Record
√
Playlist
Scheduled Record List
√
Start
End
Mode
03:05 AM 05:05 AM SP
00:45 SP
ENTER
RETURN
EXIT
6
Press the ENTER button to confirm the edited setting.
7
Press the MENU button after finishing the operation. The menu screen will disappear.
Disc Manager
Timer Rec.
Setup
Copy
MOVE
3
ENTER
EXIT
Press the …† button to select Scheduled Record
List, then press the ENTER or √ button.
DVD-Recorder
To
Source
01
02
03
DVD
DVD
––
CH06
CH06
–––
Current Time 12:27 AM
Date
Start
End Mode Edit
01/01 03:05AM 05:05AM SP
01/02 01:06AM 03:06AM SP
––/–– ––:–– –– ––:–– –– ––
ENTER
RETURN
√
√
√
EXIT
Press the …† button to select the number of the
scheduled record list you want to edit, then press
the ENTER or √ button.
• The Edit and Delete items are displayed.
Follow these directions to delete a title from the timer
record list.
1
Press the MENU button.
2
Press the …† button to select Timer Rec., then
press the ENTER or √ button.
DVD-Recorder
Timer Record
DVD-RAM(VR)
DVD-Recorder
Scheduled Record List
DVD-RAM(VR)
No.
To
Source
01
02
03
DVD
DVD
––
CH06
CH06
–––
Current Time 12:27 AM
Date
Start
End Mode Edit
01/01 03:05AM 05:05AM
01/02 01:06AM 03:06AM
––/–– ––:–– –– ––:–– ––
√
SP Edit
√
SP Delete
√
––
Title List
Timer Record
√
Playlist
Scheduled Record List
√
Disc Manager
Timer Rec.
Setup
Copy
MOVE
MOVE
ENTER
RETURN
ENTER
RETURN
EXIT
EXIT
English - 65
Recording
No.
MOVE
Deleting the
Scheduled Record List
Scheduled Record List
DVD-RAM(VR)
4
RETURN
00995J(00)_VR330_AFS-Eng2
3
2006.4.13
Page 66
Press the …† button to select Scheduled
Record List, then press the ENTER or √ button.
DVD-Recorder
Current Time 12:27 AM
No.
To
Source
01
02
03
DVD
DVD
––
CH06
CH06
–––
MOVE
Basic VCR Recording
Scheduled Record List
DVD-RAM(VR)
4
7:4 PM
Date
Start
End Mode Edit
01/01 03:05AM 05:05AM SP
01/02 01:06AM 03:06AM SP
––/–– ––:–– –– ––:–– –– ––
ENTER
RETURN
√
√
√
EXIT
Press the …† button to select the number of the
scheduled record list you want to delete, and then
press the ENTER button.
• The Edit and Delete items are displayed.
Before starting
1. Check TV channel and Antenna connections.
2. Check the remaining time on the tape.
You can record a TV show in progress by inserting a
blank tape and pressing the (REC) button. You can
even add time in preset increments up to 4 hours by
pressing the (REC) button repeatedly.
Be sure your videotape has a Record Safety
Tab. If the tab is missing, you can cover the
opening with a small piece of tape.
Note
DVD-Recorder
Scheduled Record List
DVD-RAM(VR)
To
Source
01
02
03
DVD
DVD
––
CH06
CH06
–––
MOVE
Recording
5
Current Time 12:27 AM
No.
Date
Start
End Mode Edit
√
01/01 03:05AM 05:05AM SP Edit
√
01/02 01:06AM 03:06AM SP Delete
√
––/–– ––:–– –– ––:–– –– ––
ENTER
RETURN
EXIT
Press the …† button to select Delete, then press
the ENTER or √ button.
• You will be prompted with the delete confirm
message such as “Do you want to delete
‘No.01’?”.
Scheduled Record List
DVD-Recorder
DVD-Recorder
DVD-RAM(VR)
DVD-RAM(VR)
No.
No.
To
To
01
01
02
02
03
03
DVD
DVD
DVD
DVD
––
Current
Current Time
Time 12:27
12:27 AM
AM
Source
Source
Date
Date Start
Start
No. 01
Yes
MOVE
End
End Mode
Mode Edit
Edit
CH06
05:05AM SP
CH06 01/01
01/01 03:05AM
03:05AM 05:05AM
SP
CH06
03:06AM SP
CH06 01/02
01/01 01:06AM
01:06AM 03:06AM
SP
Do you––want
to delete
‘N0.01’?
–––
//–– ––:––
: –– ––::–– –– ––
ENTER
Warning: Do not cover this opening unless you
1
Insert a blank VHS tape into the VCR deck.
• Make sure the tape is long enough to record the
entire program.
2
Press the Number buttons or the CH/TRK ( / )
buttons to select the desired channel.
Press the INPUT SEL. button to select AV 1, AV 2
or DV if recording from an external device connected to the input jacks of the recorder.
3
Press the REC SPEED button on the remote control to set the Record Speed to one of the following options:
• SP – Standard Play, for best picture quality.
√
√
√
√
√
√
• SLP – Super Long Play, for maximum recording
time (3 times SP).
NO
RETURN
are sure you want to record over the tape.
CAUTION
EXIT
The selected Record Speed will appear on the
front panel and on-screen displays.
Note
6
7
Press the œ √ buttons to select Yes, then press
the ENTER button.
• The selected title will be deleted from the list.
Press the MENU button after finishing the operation. The menu screen will disappear.
Maximum Recording Time - SP vs. SLP
Tape Length
Note
66 - English
SLP (Super Long Play)
T-120
Approx. 2 hrs
Approx. 6 hrs
T-160
Approx. 2hrs 40 mins
Approx. 8 hrs
T-180
Approx. 3 hrs
Approx.9 hrs
You can not delete programs that are currently
being recorded.
SP (Standard Play)
When you watch or record on the VCR during
Note
DVD Recording, some function buttons may
not operate.
The message “This function is not available.”
will be displayed.
00995J(00)_VR330_AFS-Eng2
4
5
2006.4.13
7:5 PM
Page 67
Press the (REC) button on the remote control or
front panel.
For options while recording is in progress, see
“Special Recording Features”.
1
To Watch a Different Channel from the
One being Recorded
2
Watch a different media during recording
3
To Add Recording Time
4
Recording on the DVD and VCR at the
same time
Press the STOP button to stop or finish a recording in progress.
Pausing / Resuming
• Press the REC PAUSE button to pause a recording
in progress.
• Press the REC PAUSE button again during pause to
resume recording.
• You can switch channels by pressing the CH/TRK
( / ) buttons while recording pauses.
Check Remaining Time
1
Press INFO button on the remote control.
Following information will be displayed.
(Current deck status, recording speed, remaining
time, input channel, current time.)
VCR
STOP
00:01:32
SP
Rem 01:41
CH6
Sun Jan 01. 2006
You can watch a DVD during VCR recording or
watch a Video tape during DVD recording.
• During VCR recording, insert a DVD in the DVD
deck. The output will automatically change to the
DVD and start playback.
• During DVD recording, insert a Video tape in the
VCR deck. The output will automatically change
to the VCR and start playback. (Only if tape is
missing the safety tab)
Refer to the One-Touch Recording (OTR).
(See page 62)
You can record on the DVD and VCR at the same
time, but both modes must be set up to record
separately.
• Press the DVD/VCR button to set the unit to
DVD or VCR mode.
• Choose AV input mode (CH, AV1, AV2 or DV).
for DVD or VCR.
• Choose REC mode for DVD or VCR.
• Press REC button for DVD or VCR.
01:08 AM
When the DVD Recorder & VCR is connected
Note
Special Recording
Features
to your TV using an S-Video or component
video cable, the video tape's playback screen
will not be displayed during DVD recording.
You cannot record different channels at the same
time.
The DVD and VCR cannot start recording at the
exact same time. You must set one mode to start
recording, then the other.
While a recording is in progress, you can watch a different media, or add recording time in preset increments. (for example, you can watch VCR playback
while recording from a DVD and vice-versa)
English - 67
Recording
-RAM
STOP
00:01:06
XP
Rem 00:26
CH6
When you watching through the Antenna input
during recording, Press the TV/VCR button on the
remote control. Change the channel you want to
watch with the TV's remote.
00995J(00)_VR330_AFS-Eng2
2006.4.13
7:5 PM
Page 68
To copy from "Edit Copylist", you need to make a
copylist in advance.
Select "New Copylist" and create the new playlist.
(See pages 79)
If you want to copy directly, choose "Direct Copy".
On DVD-RW(V)/DVD+RW/±R disc, you can only use
Direct copy function.
Copy to DVD or VCR
You can copy from the DVD to VCR or VCR to DVD.
Check the remaining time on the tape and Disc.
Press the …† buttons to select desired copylist,
then press the ENTER or √ button.
5
DVD-Recorder
Edit Copylist
DVD-RAM(VR)
To copy from DVD to VCR
No. Title
Length Edit
Play
01 JAN/01/2006 12:0 00:00:11 √
Rename
02 JAN/01/2006 12:0 00:00:09 √
Edit Scene
Copy
JAN/01/2006 12:00 AM
1
With the unit in Stop mode, press the MENU
button.
2
Press the …† buttons to select Copy, then press
the ENTER or √ button.
DVD-Recorder
JAN/01/2006 12:00 AM
MOVE
Copy
RETURN
EXIT
DVD-Recorder
Edit Copylist
DVD-RAM(VR)
Title List
DVD-->VCR
√
Playlist
VCR-->DVD
√
No. Title
Length Edit
Play
01 JAN/01/2006 12:0 00:00:11 √
Rename
02 JAN/01/2006 12:0 00:00:09 √
Edit Scene
Disc Manager
Copy
Timer Rec.
JAN/01/2006 12:00 AM
Setup
1 Scene
Delete
JAN/01/2006 12:00 AM
Copy
MOVE
Recording
ENTER
Press the …† buttons to select Copy, then press
the ENTER or √ button.
6
DVD-RAM(VR)
3
Delete
1 Scene
(VR mode)
ENTER
RETURN
EXIT
MOVE
Press the …† buttons to select DVD --> VCR,
then press the ENTER or √ button.
DVD-Recorder
DVD-->VCR
DVD-RAM(VR)
Title List
New Copylist
√
Playlist
Edit Copylist
√
Disc Manager
Direct Copy
√
Timer Rec.
Setup
ENTER
RETURN
EXIT
Direct copy DVD to VCR
• Insert a DVD disc you want to copy.
• Insert a VHS tape.
• Press the VCR copy button on front panel or
remote control (TO VCR).
• To stop recording, press the STOP button.
Copy
MOVE
ENTER
RETURN
EXIT
Copy function is not allowed in progressive
4
Press the …† buttons to select Edit Copylist,
then press the ENTER or √ button.
DVD-Recorder
Edit Copylist
DVD-RAM(VR)
No. Title
Length Edit
01 JAN/01/2006 12:0 00:00:11 √
02 JAN/01/2006 12:0 00:00:09 √
JAN/01/2006 12:00 AM
1 Scene
JAN/01/2006 12:00 AM
MOVE
68 - English
ENTER
RETURN
EXIT
Note
scan mode.
00995J(00)_VR330_AFS-Eng2
2006.4.13
7:5 PM
Page 69
5
To copy from VCR to DVD
1
With the unit in Stop mode, press the MENU
button in stop mode.
2
Press the …† buttons to select Copy, then press
the ENTER or √ button.
DVD-Recorder
You can use the √II, Iœœ or √√I, œœ or √√
buttons to search for the end position.
Press the ENTER button at the end point.
• A copylist will be generated.
Repeat the above steps to create the copylist.
• In VCR mode, the copylist cannot be saved.
DVD-Recorder
VCR-->DVD
DVD-RAM(VR)
No. Start
End
Edit
01 00 : 00: 37
02 : :
00:03:45
: :
√
√
Copy
DVD-RAM(VR)
00:01:07
Title List
DVD-->VCR
√
Playlist
VCR-->DVD
√
FF
Copy All
Disc Manager
MOVE
ENTER
RETURN
EXIT
Timer Rec.
Setup
Copy
MOVE
3
ENTER
RETURN
EXIT
6
DVD-Recorder
Press the …† buttons to select VCR-->DVD, then
press the ENTER or √ button.
DVD-Recorder
Press the …† buttons to select desired copylist,
then press the ENTER or √ button.
VCR-->DVD
DVD-RAM(VR)
No. Start
End
Edit
01 00 : 00: 37
02 : :
00:03:45
Play
: :
Copy
√
√
Delete
VCR-->DVD
00:01:07
DVD-RAM(VR)
No. Start
01
:
End
:
:
Edit
:
STOP
Copy All
√
MOVE
ENTER
RETURN
EXIT
00:00:00
STOP
Copy All
MOVE
ENTER
RETURN
EXIT
7
Press the …† buttons to select Copy, then press
the ENTER or √ button.
DVD-Recorder
VCR-->DVD
DVD-RAM(VR)
No. Start
End
Edit
01 00 : 00: 37
02 : :
00:03:45
: :
√
√
00:01:07
DVD-Recorder
VCR-->DVD
RPS
DVD-RAM(VR)
Copy All
No. Start
End
01 00 : 00: 37
:
Edit
:
√
00:01:07
FF
Copy All
MOVE
ENTER
RETURN
EXIT
MOVE
ENTER
RETURN
EXIT
• The VCR will fast forward, searching for a start
position and then automatically start a copy.
• The Start and End points may not match up
exactly.
• If you want to copy all content, select Copy All.
Direct copy VCR to DVD
• Insert the VHS tape you want to copy.
• Insert a recordable DVD disc.
• Press DVD copy button on front panel or remote
control(TO DVD).
• To stop recording press the STOP button.
English - 69
Recording
4
You can use the √II, Iœœ or √√I, œœ or √√
buttons to search for the Start position.
Press the ENTER button at the start point.
00995J(00)_VR330_AFS-Eng2
2006.4.13
7:5 PM
Page 70
Playing the Title List
Editing
This section introduces basic functions of DVD
editing and explains both edit functions for the
recording on a disc and edit functions for the
entire disc.
Follow these instructions to play back a scene from the
Title List.
Using the TITLE LIST button
Press the TITLE LIST button.
The Title List screen is displayed.
1
Title List
DVD-RAM(VR)
1/4
JAN/01/2006
No.
JAN/01/2006 12:00 AM CH1
Title
01 JAN/01/2006
02 JAN/01/2006
03 JAN/01/2006
04 JAN/01/2006
Length Edit
12:00
12:30
01:00
01:30
00:00:11
00:00:09
00:01:36
00:00:11
√
√
√
√
JAN/01/2006
SP
MOVE
Playing the Title List .........................................................70
EXIT
Press the …† buttons to select a title you want to
play from Title List, and then press the PLAY button.
The selected title will be played back.
3
To stop title play, press the STOP button.
To return the title list screen, press the TITLE
LIST button.
Renaming(Labeling) a Title .............................................72
Deleting a Title ................................................................74
RETURN
2
Basic Editing (Title List) ...................................................72
Locking(Protecting) a Title ..............................................73
ENTER
Deleting a Section of a Title ............................................74
Editing a Chapter.............................................................76
Using the MENU button
Dividing a Title ................................................................78
Advanced Editing (Playlist)...............................................79
Editing
Creating a playlist ...........................................................79
Playing Titles in the Playlist............................................80
Renaming a Playlist Title.................................................80
1
Press the MENU button.
DVD-Recorder
Title List
DVD-RAM(VR)
Editing a Scene for the Playlist........................................81
Copying a Playlist Title to the VCR ................................84
Title List
Title List
√
Playlist
Disc Manager
Deleting a Playlist Title from the Playlist .......................85
Disc Manager ...................................................................85
Timer Rec.
Setup
Copy
Editing the Disc Name .....................................................85
Disc Protection.................................................................86
Formatting a Disc ............................................................87
Finalizing a disc...............................................................87
Unfinalizing a disc (V/VR mode) .....................................88
Delete All Title Lists ........................................................89
Edit Compatible ...............................................................90
70 - English
MOVE
ENTER
RETURN
EXIT
00995J(00)_VR330_AFS-Eng2
2
2006.4.13
7:5 PM
Page 71
Title List Screen Elements
Press the …† buttons to select Title List, then
press the ENTER or √ button twice.
# $
The Title List screen is displayed.
Title List
DVD-RAM(VR)
No.
Title
01 JAN/01/2006
02 JAN/01/2006
03 JAN/01/2006
04 JAN/01/2006
JAN/01/2006 12:00 AM CH1
00:00:11
00:00:09
00:01:36
00:00:11
No.
√
√
√
!
√
JAN/01/2006 01:00 AM CH1
JAN/01/2006
@
SP
MOVE
3
ENTER
RETURN
EXIT
Press the …† buttons to select a Title, then press
the ENTER or √ button.
The Edit menu is displayed:Play, Rename, Delete,
Edit, Protection(See pages 72~75)
Title List
DVD-RAM(VR)
3/4
JAN/01/2006
No.
Title
01 JAN/01/2006
02 JAN/01/2006
03 JAN/01/2006
04 JAN/01/2006
JAN/01/2006 01:00 AM CH1
JAN/01/2006
√
√
√
√
Edit
XP
Protection
MOVE
4
Length Edit
12:00 00:00:11
12:30 00:00:09
Play
01:00 00:01:36
Rename
01:30 00:00:11
Delete
ENTER
RETURN
EXIT
√
00:00:11
00:00:09
00:01:36
00:00:11
JAN/01/2006 12:00 AM CH1
JAN/01/2006
XP
XP
√
02 JAN/01/2006 12:30 00:00:09 √
Play
√
03 JAN/01/2006 01:00 00:01:36 √
Rename
√
04 JAN/01/2006 01:30 00:00:11 √
Delete
Edit
Protection
MOVE
RETURN
ENTER
1/4
Length Edit
√
01 JAN/01/2006 12:00 00:00:11 √
ENTER
EXIT
EXIT
&
! Playback screen for recorded titles.
@ Information window for the selected title: Title name,
recording date, lock status, recording mode
# Recorded title No.
$ Recorded title name
% Recording Length (i.e., the playing time)
^ Edit menu
Play: Plays the selected title.
Rename: Changes the name of a selected title.
Delete: Deletes the selected title from the list.
Edit: Deletes a section of title.
Protection: Locks or unlocks the selected title.
& Button display
This may depend on the disc type.
Note
VR
1/4 JAN/0
Length Edit
No. Title
12:00
12:30
01:00
01:30
JAN/01/2006
MOVE
Press the …† buttons to select Play to play the
title list, then press the ENTER button.
The selected title will be played back.
– RAM
Title
01 JAN/01/2006
02 JAN/01/2006
03 JAN/01/2006
04 JAN/01/2006
Title List
^
DVD-RW(VR)
JAN/01/2006
Length Edit
12:00
12:30
01:00
01:30
DVD-Recorder Title List
DVD-RAM(VR)
1/4
JAN/01/2006
%
DVD-RW(V)/DVD+RW/±R has limited editing
function.
XP
Free Space Function
This function is only available with DVD+RW discs.
If existing titles are deleted, new free space will be
created.
When you operate free space function, on-air TV
images will appear on the left side of the title list.
5
Press the STOP button to stop playing.
To return the title list screen, press the TITLE LIST
button.
Note
pressing the ANYKEY button.
DVD-RAM(VR)
Title
3/4
Time
00: 00: 07
Subtitle
Off
Audio
ENG
Repeat
Off
Off
Zoom
MOVE
D 2CH
Press the TITLE LIST button.
The Title List screen is displayed.
Or use the MENU button.
• Press the MENU button.
• Press the …† buttons to select Title List, then
press the ENTER or √ button twice.
Title List
DVD+RW
1/4
JAN/01/2006
No.
CHANGE
JAN/01/2006 12:00 AM CH1
Title
01 JAN/01/2006
02 JAN/01/2006
03 JAN/01/2006
04 Free Space
Length Edit
12:00
12:30
01:00
01:30
00:00:11
00:00:09
00:01:36
01:58:04
√
√
√
√
JAN/01/2006
Press the …† buttons to select Title.
Press the œ √ buttons to select to play the
SP
MOVE
ENTER
RETURN
EXIT
title list, then press the ENTER button.
English - 71
Editing
You can also play a recorded program by
1
00995J(00)_VR330_AFS-Eng2
2
2006.4.13
Page 72
Press the …† buttons to select a Title you want to
delete, then press the ENTER or √ button.
Title List
DVD+RW
No.
JAN/01/2006 01:00 AM CH1
Title
01 JAN/01/2006
02 JAN/01/2006
03 JAN/01/2006
04 Free Space
Length Edit
Play00:00:11 √
12:00
Rename
12:30
00:00:09 √
01:00
00:01:36 √
Delete
01:30
01:58:04 √
Protection
Chapter Edit
JAN/01/2006
Renaming(Labeling) a Title
Divide Title
SP
MOVE
Basic Editing (Title List)
3/4
JAN/01/2006
3
7:5 PM
ENTER
RETURN
EXIT
Follow these instructions to rename a title list name,
i.e., to edit the title of a recorded program.
Press the …† button to select Delete, then press
the ENTER or √ button.
Title List
DVD+RW
3/4
JAN/01/2006
1
Press the TITLE LIST button.
The Title List screen is displayed.
Do you want to delete?
Or use the MENU button.
• Press the MENU button.
• Press the …† buttons to select Title List, then
press the ENTER or √ button twice.
JAN/01/2006 01:00 AM CH1
Yes
JAN/01/2006
No
SP
MOVE
ENTER
RETURN
EXIT
• You will be prompted with the confirmation
message 'Do you want to delete?'.
4
1/4
JAN/01/2006
No.
Press the œ √ buttons to select Yes, then press
the ENTER button.
The selected title has been deleted and Free
Space is displayed.
JAN/01/2006 01:00 AM CH1
Title
01 JAN/01/2006
02 JAN/01/2006
03 JAN/01/2006
04 JAN/01/2006
Length Edit
12:00
12:30
01:00
01:30
00:00:11
00:00:09
00:01:36
00:00:11
√
√
√
√
JAN/01/2006
SP
MOVE
ENTER
RETURN
EXIT
Title List
DVD+RW
Free Space
4/4
No.
Free Space
Title List
DVD-RAM(VR)
Title
01 JAN/01/2006
02 JAN/01/2006
03 JAN/01/2006
04 Free Space
Length Edit
12:00
12:30
01:00
01:30
00:00:11
00:00:09
00:01:36
01:58:04
√
√
√
√
2
Press the …† buttons to select a title you want to
rename from the Title List, then press the ENTER
or √ button.
CH1
SP
Title List
DVD-RAM(VR)
MOVE
ENTER
RETURN
EXIT
3/4
JAN/01/2006
No.
• New free Space will be created equal to the
length of the deleted title.
Editing
JAN/01/2006 01:00 AM CH1
- Recording a title
1
Press the …† button to select Free Space, then
press the ENTER or √ button.
On-air TV images will appear on the left side of
the title list.
Title List
DVD+RW
Free Space
4/4
No.
Free Space
Title
01 JAN/01/2006
02 JAN/01/2006
03 JAN/01/2006
04 Free Space
Length Edit
01 JAN/01/2006
02 JAN/01/2006
03 JAN/01/2006
04 JAN/01/2006
12:00 00:00:11
12:30 00:00:09
Play
01:00 00:01:36
Rename
01:30 00:00:11
Delete
JAN/01/2006
Edit
XP
Protection
MOVE
3
Title
ENTER
RETURN
√
√
√
√
EXIT
Press the …† buttons to select Rename, then
press the ENTER or √ button.
The Rename screen is displayed.
Length Edit
12:00 00:00:11
12:30 00:00:09
01:00 00:01:36
Recording
01:30
01:58:04
√
√
√
√
DVD-Recorder
Rename
DVD-RAM(VR)
JAN/01/2006 01:00 AM CH1
CH1
SP
MOVE
ENTER
RETURN
EXIT
Save
Back Space
2
Press the ENTER button.
72 - English
MOVE
Space
ENTER
Delete
RETURN
Clear
EXIT
00995J(00)_VR330_AFS-Eng2
4
2006.4.13
7:5 PM
Page 73
Select the desired characters using the …† œ √
buttons, press the ENTER button.
DVD-Recorder
Locking(Protecting) a Title
Follow these instructions to lock a title to protect it from
accidental deletion.
Rename
DVD-RAM(VR)
Sport(A1)
1
Or use the MENU button.
• Press the MENU button.
• Press the …† buttons to select Title List, then
press the ENTER or √ button twice.
Save
Back Space
MOVE
Space
ENTER
Delete
RETURN
Press the TITLE LIST button.
The Title List screen is displayed.
Clear
EXIT
Title List
DVD-RAM(VR)
JAN/01/2006
• Back Space: Moves the cursor one position
backwards.
• Space: Enters a blank and moves the cursor one
forward (to the right).
• Delete: Deletes the character at the cursor
position.
• Clear: Deletes all the character inputs.
• Save: Registers the character inputs.
5
Press the …† œ √ buttons to select Save, and
then press the ENTER button.
The changed title name is displayed in the title field
of the selected title.
JAN/01/2006 12:00 AM CH1
MOVE
2
Title
ENTER
RETURN
√
√
√
√
RETURN
EXIT
Press the …† buttons to select a title you want to
protect in the Title List, then press the ENTER or
√ button.
Title List
3/4
No.
Title
01 JAN/01/2006
02 JAN/01/2006
03 JAN/01/2006
04 JAN/01/2006
JAN/01/2006
Length Edit
EXIT
00:00:11
00:00:09
00:01:36
00:00:11
JAN/01/2006
MOVE
3
Length Edit
12:00 00:00:11
12:30 00:00:09
Play
01:00 00:01:36
Rename
01:30 00:00:11
Delete
√
√
√
√
Edit
EP
01 JAN/01/2006 12:00 00:00:11 √
02 JAN/01/2006 12:30 00:00:09 √
03 Sport(A1)
00:01:36 √
04 JAN/01/2006 01:30 00:00:11 √
XP
12:00
12:30
01:00
01:30
DVD-RAM(VR)
JAN/01/2006
MOVE
ENTER
JAN/01/2006 12:00 AM CH1
No.
01 JAN/01/2006
02 JAN/01/2006
03 JAN/01/2006
04 JAN/01/2006
Length Edit
SP
3/4
Sport(A1)
Title
JAN/01/2006
Title List
DVD-RAM(VR)
Sport(A1)
1/4
No.
Protection
ENTER
RETURN
EXIT
Press the …† buttons to select Protection, then
press the ENTER or √ button.
Title List
DVD-RAM(VR)
JAN/01/2006
5/31
Title Protection :
JAN/01/2006 12:00 AM CH1
On
JAN/01/2006
Off
MOVE
4
ENTER
RETURN
EXIT
Press the œ √ buttons to select On, then press
the ENTER button. The lock icon on the information window for the selected title changes to the
locked status. ( ➝ )
Title List
DVD-RAM(VR)
3/4
JAN/01/2006
No.
JAN/01/2006 12:00 AM CH1
Title
01 JAN/01/2006
02 JAN/01/2006
03 JAN/01/2006
04 JAN/01/2006
Length Edit
12:00
12:30
01:00
01:30
00:00:11
00:00:09
00:01:36
00:00:11
√
√
√
√
JAN/01/2006
EP
MOVE
ENTER
RETURN
EXIT
English - 73
Editing
EP
00995J(00)_VR330_AFS-Eng2
2006.4.13
7:5 PM
Page 74
DVD-RW(Video mode),DVD+RW, DVD±R : Since
Playlist is not present, the message ‘Do you want
to delete?’ is displayed.
Deleting a Title
Follow these instructions to delete a title from the Title
List.
Title List
DVD-RW(V)
JAN/01/2006
1
Press the TITLE LIST button.
The Title List screen is displayed.
1/4
Do you want to delete?
JAN/01/2006 12:00 AM CH1
Yes
JAN/01/2006
Or use the MENU button.
• Press the MENU button.
• Press the …† buttons to select Title List, then
press the ENTER or √ button twice.
MOVE
ENTER
RETURN
EXIT
• The message may depend on the type of disc.
Title List
DVD-RAM(VR)
1/4
JAN/01/2006
No.
JAN/01/2006 12:00 AM CH1
Title
01 JAN/01/2006
02 JAN/01/2006
03 JAN/01/2006
04 JAN/01/2006
Length Edit
12:00
12:30
01:00
01:30
00:00:11
00:00:09
00:01:36
00:00:11
√
√
4
Press the œ √ buttons to select Yes, then press
the ENTER button.
√
√
You cannot delete a protected title.
JAN/01/2006
SP
MOVE
No
EP
ENTER
RETURN
EXIT
Note
If you want to delete a protected title, select
Off in the Title Protection menu.
Once a title is deleted from the Title List it
cannot be recovered.
2
Press the …† buttons to select a title you want to
delete in the Title List, then press the ENTER or √
button.
be deleted.
With DVD±R, titles are only deleted from the
menu, however, the Title remains physically
on the disc.
Title List
DVD-RAM(VR)
1/4
JAN/01/2006
No.
JAN/01/2006 12:00 AM CH1
Title
01 JAN/01/2006
02 JAN/01/2006
03 JAN/01/2006
04 JAN/01/2006
Length Edit
12:00 00:00:11
12:30 00:00:09
Play
01:00 00:01:36
Rename
01:30 00:00:11
Delete
JAN/01/2006
Edit
EP
Protection
MOVE
Once DVD±R, DVD-RW is finalized, it cannot
ENTER
RETURN
√
√
√
√
EXIT
Deleting a Section of a Title
Follow these instructions to delete a section of a
Title List title.
(VR mode)
Editing
3
Press the …† buttons to select Delete, then
press the ENTER or √ button.
You will be prompted with a confirmation message.
DVD-RAM(VR), DVD-RW(VR mode) : Since
Playlist is present, the message ‘Do you want to
delete? (Related playlists may be deleted.)’ is displayed.
Title List
DVD-RAM(VR)
1
Press the TITLE LIST button.
The Title List screen is displayed.
Or use the MENU button.
• Press the MENU button.
• Press the …† buttons to select Title List, then
press the ENTER or √ button twice.
Title List
DVD-RAM(VR)
1/4
JAN/01/2006
1/4
JAN/01/2006
No. Title
Do you want to delete?
(Related playlists
may be deleted.)
JAN/01/2006 12:00 AM CH1
JAN/01/2006 12:00 AM CH1
Yes
JAN/01/2006
Length Edit
01 JAN/01/2006
02 JAN/01/2006
03 JAN/01/2006
04 JAN/01/2006
12:00
12:30
01:00
01:30
00:00:11
00:00:09
00:01:36
00:00:11
√
√
√
√
JAN/01/2006
No
SP
EP
MOVE
MOVE
74 - English
ENTER
RETURN
EXIT
ENTER
RETURN
EXIT
00995J(00)_VR330_AFS-Eng2
2
2006.4.13
Page 75
Press the …† buttons to select a title you want to
delete from the Title List, then press the ENTER
or √ button.
Press the ENTER button at the end point.
The image and end point time are displayed in the
Section deletion ending point window.
Edit Title List
DVD-RAM(VR)
3/4
JAN/01/2006
No.
JAN/01/2006 12:00 AM CH1
Title
01 JAN/01/2006
02 JAN/01/2006
03 JAN/01/2006
04 JAN/01/2006
Length Edit
12:00 00:00:11
12:30 00:00:09
Play
01:00 00:01:36
Rename
01:30 00:00:11
Delete
JAN/01/2006
Edit
EP
Protection
MOVE
5
Title List
DVD-RAM(VR)
3
7:5 PM
ENTER
RETURN
Tist List No. 03
Start
End
√
√
√
√
00:00:01
00:00:15
00:00:15
Start
EXIT
End
Delete
MOVE
Press the …† buttons to select Edit, then press
the ENTER or √ button.
The Edit Title List screen is displayed.
6
ENTER
Return
RETURN
Press the œ √ buttons to select Delete, then
press the ENTER button.
Edit Title List
DVD-RAM(VR)
Edit Title List
DVD-RAM(VR)
Tist List No. 03
Start
End
Tist List No. 03
Start
End
00:00:02
00:00:00
00:00:06
00:00:00
End
MOVE
Delete
ENTER
Start
Return
RETURN
End
Delete
MOVE
ENTER
Return
RETURN
EXIT
EXIT
Edit Title List
DVD-RAM(VR)
4
00:00:06
00:00:00
√
Start
EXIT
Press the ENTER button at the starting point.
The image and starting point time are displayed in
the section deletion starting point window.
Edit Title List Screen Elements
Title List No. 03
Start
End
Do you want to delete?
(Deleted part will not be restored.)
00:00:10
Yes
Start
End
No
Delete
Return
Edit Title List
DVD-RAM(VR)
MOVE
ENTER
RETURN
EXIT
Tist List No. 03
Start
End
00:00:02
Start
End
MOVE
7
00:00:00
00:00:02
√
Delete
ENTER
Return
RETURN
EXIT
Edit Title List
The length of the section to be deleted must
Tist List No. 03
Start
End
00:00:02
00:00:02
√
Start
MOVE
End
00:00:00
➂
➃
Delete
ENTER
Return
RETURN
EXIT
1 Playback bar
2 Playtime
3 Section deletion starting point window and time
4 Section deletion end point window and time
• Select the start and end points of the section
you want to delete using the playback related
buttons.
• Playback related buttons: (√II,Iœœ,œœ,√√).
Note
be at least 5 seconds long.
If the length of the section to be deleted is
less than 5 seconds, you will be prompted
with the message 'The range is too short.'.
If the end time precedes the starting time,
you will be prompted with the message ‘End
point cannot be marked earlier than start
point.’.
The section cannot be deleted when it
includes a still picture.
Press the MENU button after the operation
has finished.
The Title List screen will disappear.
English - 75
Editing
DVD-RAM(VR)
①
②
Press the œ √ buttons to select Yes, then press
the ENTER button.
The selected section has been deleted.
To return to the Title List screen, press the œ √
buttons to select Return.
00995J(00)_VR330_AFS-Eng2
2006.4.13
7:5 PM
Page 76
Editing a Chapter
Chapter Edit Screen Elements
You can make your own chapters on DVD+RWs and
edit them using the Chapter Edit menu.
1
①
②
Press the TITLE LIST button.
The Title List screen is displayed.
Title List
DVD+RW
Chapter : 1/3 Show
00:00:00
√
Add
Or use the MENU button.
• Press the MENU button.
• Press the …† buttons to select Title List, then
press the ENTER or √ button twice.
Chapter Edit
DVD+RW
Delete
MOVE
Hidden
ENTER
Delete All
RETURN
Return
➂
➃
EXIT
1. Current chapter number and status
2. Playback bar
3. Playtime
4. Chapter Edit menu
1/4
JAN/01/2006
No.
JAN/01/2006 12:00 AM CH1
Title
Length Edit
01 JAN/01/2006 12:00 00:04:48 √
02 JAN/01/2006 12:30 00:01:47 √
03 JAN/01/2006 01:00 00:49:57 √
04 Free Space
01:13:08 √
Adding a chapter
JAN/01/2006
SP
MOVE
2
ENTER
RETURN
EXIT
Press the …† buttons to select a title containing a
chapter you want to edit, then press the ENTER
or √ button.
Chapter Edit
DVD+RW
3/4
JAN/01/2006
No.
JAN/01/2006 01:00 AM CH1
Chapter : 1/2 Show
Title
Length Edit
Play00:04:48 √
01 JAN/01/2006 12:00
Rename
02 JAN/01/2006 12:30
00:01:47 √
03 JAN/01/2006 01:00
00:49:57 √
Delete
04 Free Space
01:13:08 √
Protection
00:10:10
√
Add
Delete
MOVE
Hidden
ENTER
Delete All
RETURN
Divide Title
SP
ENTER
RETURN
EXIT
• Playback related buttons: (√II,Iœœ,√√I,œœ,√√).
EXIT
Press the …† buttons to select Chapter Edit,
then press the ENTER or √ button.
The Chapter Edit screen is displayed.
5
Press the œ √ buttons to select Return, and then
press the ENTER button.
The edited title will now have the chapter you
added.
Title List
DVD+RW
3/4
JAN/01/2006
Editing
Return
Chapter Edit
JAN/01/2006
MOVE
Select the point where you want to add a chapter
using the playback related buttons, then press the
ENTER button at that point.
Each time you press the ENTER button, a new
chapter will be added.
Title List
DVD+RW
3
4
No.
Chapter Edit
DVD+RW
JAN/01/2006 01:00 AM CH1
Title
Length Edit
01 JAN/01/2006 12:00 00:04:48 √
02 JAN/01/2006 12:30 00:01:47 √
03 JAN/01/2006 01:00 00:49:57 √
04 Free Space
01:13:08 √
JAN/01/2006
SP
Chapter : 1/1 Show
00:00:00
√
Add
MOVE
Delete
Hidden
ENTER
Delete All
RETURN
MOVE
ENTER
RETURN
EXIT
Return
EXIT
You can make up to 99 chapters in a title and
Note
254 chapters in a disc.
The edited chapters are shown on existing
DVD players only after performing the Edit
Compatible function. (See page 90)
If you add a chapter, the title is divided at that
point; If you add a chapter onto a title that has
only one chapter, it creates another chapter.
76 - English
00995J(00)_VR330_AFS-Eng2
2006.4.13
7:5 PM
Page 77
5
Deleting a chapter
Press the œ √ buttons to select Hidden, and then
press the ENTER button.
The selected chapter is hidden.
Follow steps 1 to 3 in page 76
Chapter Edit
DVD+RW
4
Select a chapter you want to delete using the
playback related buttons.
Chapter Edit
DVD+RW
Chapter : 2/4 Hidden
00:15:00
√
Add
Delete
MOVE
Hidden
ENTER
Delete All
Return
RETURN
EXIT
Chapter : 2/4 Show
Delete
MOVE
• To finish the operation, select Return using the
œ √ buttons then press the ENTER button.
00:15:00
√
Add
Hidden
ENTER
Delete All
RETURN
Return
EXIT
• Playback related buttons: (√II,Iœœ,√√I,œœ,√√).
5
Press the œ √ buttons to select Delete, and then
press the ENTER button.
The selected chapter will be deleted.
Note
one chapter in the selected title.
The hidden chapters are not shown on the
existing DVD players.
Hidden menu is changed to Show with a
Chapter Edit
DVD+RW
If there is only one chapter, it can’t be hidden.
Hidden/Show menu is not available if there is
chapter playing back. You can make the hidden chapter shown by pressing the ENTER
button at Show menu.
Chapter : 2/3 Show
00:15:00
√
Add
Delete
MOVE
Hidden
ENTER
Delete All
RETURN
Return
EXIT
• To finish the operation, select Return using the
œ √ buttons then press the ENTER button.
Note
First chapter can’t be deleted.
Delete menu is not available if there is one
Deleting all chapters
Follow steps 1 to 3 in page 76
4
Press the œ √ buttons to select Delete All, and
then press the ENTER button.
Chapter Edit
DVD+RW
chapter in the selected title.
When deleting a chapter, only the chapter marker
is actually deleted, not the recorded video.
Deleting a chapter can't be canceled.
Do you want to delete all chapter marks?
Yes
√
Add
MOVE
No
Hidden
ENTER
Delete All
RETURN
00:00:00
Return
EXIT
Follow steps 1 to 3 in page 76
4
Select a chapter you want to hide using the
playback related buttons.
5
Press the œ √ buttons to select Yes, and then
press the ENTER button.
Chapter Edit
DVD+RW
When deleting a chapter, only the chapter
Note
Chapter : 2/4 Show
00:15:00
√
Add
MOVE
Delete
Hidden
ENTER
Delete All
RETURN
Return
EXIT
marker is actually deleted, not the recorded
video.
Delete All menu is not available if there is one
chapter in the selected title.
• Playback related buttons: (√II,Iœœ,√√I,œœ,√√).
English - 77
Editing
Hiding a chapter
Delete
00995J(00)_VR330_AFS-Eng2
2006.4.13
7:5 PM
Page 78
Dividing a Title
Follow these instructions to divide a long title into
several titles.
4
Select the point you want to divide using the
playback related buttons, then press the ENTER
button.
Divide Title
DVD+RW
Title List No. 03
Start
End
1
Press the TITLE LIST button.
The Title List screen is displayed.
00:00:00
00:00:00
00:010:10
√
Or use the MENU button.
• Press the MENU button.
• Press the …† buttons to select Title List, then
press the ENTER or √ button twice.
Point
Divide
MOVE
Return
ENTER
RETURN
EXIT
• Playback related buttons: (√II,Iœœ,œœ,√√).
Title List
DVD+RW
1/4
JAN/01/2006
No.
JAN/01/2006 12:00 AM CH1
Title
Length Edit
01 JAN/01/2006 12:00 00:04:48 √
02 JAN/01/2006 12:30 00:01:47 √
03 JAN/01/2006 01:00 00:49:57 √
04 Free Space
01:13:08 √
5
Press the œ √ buttons to select Divide, then
press the ENTER button.
Divide Title
DVD+RW
JAN/01/2006
SP
Title List No. 03
Start
End
MOVE
ENTER
RETURN
EXIT
Do you want to divide title?
2
(Once divided, titles cannot be merged back.)
00:00:00
Yes
No
00:010:10
Press the …† buttons to select a title you want to
divide from the Title List, then press the ENTER or
√ button.
Point
Title List
DVD+RW
3/4
JAN/01/2006
No.
JAN/01/2006 01:00 AM CH1
Title
Length Edit
Play00:04:48 √
01 JAN/01/2006 12:00
Rename
02 JAN/01/2006 12:30
00:01:47 √
03 JAN/01/2006 01:00
00:49:57 √
Delete
04 Free Space
01:13:08 √
Protection
6
Chapter Edit
JAN/01/2006
Return
ENTER
Press the œ √ buttons to select Yes, then press
the ENTER button.
The selected title has been divided into two titles.
Title List
1/5
No.
ENTER
RETURN
EXIT
JAN/01/2006 12:00 AM CH1
Editing
Press the …† buttons to select Divide Title, then
press the ENTER or √ button.
The Divide Title List screen is displayed.
JAN/01/2006
MOVE
00:04:48
00:01:47
00:19:25
00:30:32
01:13:08
√
√
√
√
√
ENTER
RETURN
EXIT
If the point length to be divided is less than 5
Note
00:00:00
00:00:00
00:00:01
√
Divide
78 - English
Length Edit
12:00
12:30
01:00
01:30
SP
Title List No. 03
Start
End
MOVE
Title
01 JAN/01/2006
02 JAN/01/2006
03 JAN/01/2006
04 JAN/01/2006
05 Free Space
Divide Title
DVD+RW
Point
EXIT
JAN/01/2006
MOVE
3
RETURN
DVD+RW
Divide Title
SP
Divide
MOVE
Return
ENTER
RETURN
EXIT
seconds, you will be prompted with the message 'The range is too short.'.
Press the MENU button after the operation
has finished.
The Title List screen will disappear.
00995J(00)_VR330_AFS-Eng2
2006.4.13
7:5 PM
Page 79
5
Advanced Editing
(Playlist)
Press the ENTER button at the end point.
DVD-Recorder
Make Scene
DVD-RAM(VR)
Scene No. 003
Start
End
00:00:02
Title List : 1/31
Creating a Playlist
End
MOVE
Playlist
DVD-RAM(VR)
Title List
New Playlist
√
Playlist
Edit Playlist
√
Return
ENTER
RETURN
EXIT
• The yellow-colored selection bar moves to the
Make icon.
With the unit in Stop mode, press the MENU
button.
Press the …† buttons to select Playlist, then
press the ENTER or √ button.
Make
• The image and end point time are displayed in
the End window.
(VR mode)
DVD-Recorder
00:00:08
Start
Follow these instructions to create a
new playlist title from a recorded title.
1
2
00:00:08
»
- To make a new playlist -
6
Disc Manager
Press the œ √ buttons to select Make, then press
the ENTER button.
A new Scene will be added to the current Playlist.
A new Make Scene screen is displayed.
Timer Rec.
Setup
You can check and see all the scenes on
Copy
MOVE
3
ENTER
RETURN
EXIT
Note
Scene No. 003
Start
End
00:00:00
Title List : 1/31
00:00:00
00:00:00
√
End
MOVE
Repeat steps 4~6 if you want to add scenes
to the playlist.
Make Scene
DVD-RAM(VR)
Start
Repeat steps 1~6 if you want to make a new
playlist.
Press the …† buttons to select New Playlist,
then press the ENTER or √ button.
The Make Scene screen is displayed.
DVD-Recorder
Edit Playlist screen.
Make
ENTER
- To return to Edit Playlist menu -
7
Press the …† buttons to select Return, then
press the ENTER button.
The Edit Playlist screen is displayed.
Return
RETURN
EXIT
DVD-Recorder
Edit Playlist
DVD-RAM(VR)
Title
Length Edit
01 JAN/01/2006 12:00 00:00:03 √
02 JAN/01/2006 12:30 00:00:25 √
03 JAN/01/2006 01:00 00:00:05 √
DVD-Recorder
Make Scene
JAN/01/2006 12:00 AM
1 Scene
JAN/01/2006 12:00 AM
DVD-RAM(VR)
Scene No. 003
Start
End
MOVE
00:00:02
Title List : 1/31
ENTER
RETURN
EXIT
00:00:00
00:00:02
√
Start
MOVE
End
Make
ENTER
Return
RETURN
EXIT
8
Press the MENU or PLAY LIST button after the
operation has finished.
The Edit Playlist screen will disappear.
• The image and time at the start point are displayed on the Start window.
• The yellow-colored selection bar moves to the
End item.
• Select the starting point of the section from
which you want to create a new scene using the
playback related buttons (√II,Iœœ,√√I,œœ,√√).
You can create up to 99 playlist titles.
Note
Depending on the kind of disc, the displayed
screen may have a slight difference.
English - 79
Editing
4
No.
Press the ENTER button at the start point.
00995J(00)_VR330_AFS-Eng2
2006.4.13
7:5 PM
Page 80
Playing Titles in the Playlist
– RAM
√
VR
EP
Follow these instructions to play the playlist titles.
(VR mode)
1
Press the PLAY LIST button with the disc stopped.
The Edit Playlist screen is displayed.
Or use the MENU button.
• Press the MENU button with the disc stopped.
• Press the …† buttons to select Playlist, then
press the ENTER or √ button.
• Press the …† buttons to select Edit Playlist,
then press the ENTER or √ button.
DVD-Recorder
Playlist
DVD-RAM(VR)
Title List
New Playlist
√
Playlist
Edit Playlist
√
4
Press the STOP button to stop playing.
The screen returns to the Edit Playlist screen.
Renaming a Playlist Title
Follow these instructions to rename a playlist title, i.e.
to edit the title of a playlist title.
Disc Manager
Timer Rec.
(VR mode)
Setup
Copy
MOVE
ENTER
RETURN
DVD-Recorder
EXIT
1
Or use the MENU button.
• Press the MENU button with the disc stopped.
• Press the …† buttons to select Playlist, then
press the ENTER or √ button.
• Press the …† buttons to select Edit Playlist,
then press the ENTER or √ button.
Edit Playlist
DVD-RAM(VR)
No.
Title
Length Edit
01 JAN/01/2006 12:00 00:00:03 √
02 JAN/01/2006 12:30 00:00:25 √
03 JAN/01/2006 01:00 00:00:05 √
JAN/01/2006 12:00 AM
1 Scene
JAN/01/2006 12:00 AM
MOVE
ENTER
RETURN
Press the PLAY LIST button with the disc stopped.
The Edit Playlist screen is displayed.
EXIT
DVD-Recorder
Edit Playlist
DVD-RAM(VR)
No.
Editing
2
3
Press the …† buttons to select the title you want
to play from the Playlist, then press the ENTER or
√ button.
The Edit Playlist menu is displayed : Play,
Rename, Edit Scene, Copy, Delete.
Press the …† buttons to select Play, then press
the ENTER or √ button.
The playlist titles will be played back.
DVD-Recorder
Edit Playlist
DVD-RAM(VR)
No.
Title
02 JAN/01/2006 12:30 00:00:25 √
Play
03 JAN/01/2006 01:00 00:00:05 √
Rename
MOVE
ENTER
02 JAN/01/2006 12:30 00:00:25 √
03 JAN/01/2006 01:00 00:00:05 √
JAN/01/2006 12:00 AM
1 Scene
JAN/01/2006 12:00 AM
MOVE
2
RETURN
EXIT
Press the …† buttons to select the title you want
to rename from the Playlist, then press the
ENTER or √ button.
The Edit menu is displayed : Play, Rename, Edit
Scene, Copy, Delete
DVD-Recorder
Edit Playlist
DVD-RAM(VR)
No.
Title
Length Edit
01 JAN/01/2006 12:00 00:00:03 √
Copy
02 JAN/01/2006 12:30 00:00:25 √
Play
03 JAN/01/2006 01:00 00:00:05 √
Rename
Delete
EXIT
Edit Scene
JAN/01/2006 12:00 AM
1 Scene
JAN/01/2006 12:00 AM
MOVE
80 - English
ENTER
Edit Scene
RETURN
Length Edit
Length Edit
01 JAN/01/2006 12:00 00:00:03 √
JAN/01/2006 12:00 AM
1 Scene
JAN/01/2006 12:00 AM
Title
01 JAN/01/2006 12:00 00:00:03 √
ENTER
Copy
Delete
RETURN
EXIT
00995J(00)_VR330_AFS-Eng2
3
2006.4.13
7:5 PM
Page 81
Press the …† buttons to select Rename, then
press the ENTER or √ button.
The Rename screen is displayed.
DVD-Recorder
Editing a Scene for the Playlist
Follow these instructions to edit scenes for a playlist.
Rename
DVD-RAM(VR)
(VR mode)
JAN/01/2006 12:00 AM
1
Save
Back Space
MOVE
4
Space
ENTER
Delete
RETURN
Or use the MENU button.
• Press the MENU button with the disc stopped.
• Press the …† buttons to select Playlist, then
press the ENTER or √ button.
• Press the …† buttons to select Edit Playlist,
then press the ENTER or √ button.
Clear
EXIT
Enter the desired characters using the …† œ √
buttons.
DVD-Recorder
Press the PLAY LIST button with the disc stopped.
The Edit Playlist screen is displayed.
DVD-Recorder
Rename
Edit Playlist
DVD-RAM(VR)
DVD-RAM(VR)
No.
Dolphin
Title
Length Edit
01 JAN/01/2006 12:00 00:00:03 √
02 JAN/01/2006 12:30 00:00:25 √
03 Dolphin
00:00:05 √
JAN/01/2006 12:00 AM
1 Scene
JAN/01/2006 12:00 AM
Save
Back Space
MOVE
Space
ENTER
Delete
RETURN
Clear
• This function is the same as the Rename
function in renaming the title list. (See page 72.)
• The maximum number of characters that can be
entered is 31.
5
MOVE
EXIT
2
Press the …† œ √ buttons to select Save, then
press the ENTER button.
The changed title is displayed in the title field of
the selected title.
DVD-Recorder
EXIT
Press the …† buttons to select the title you want
to edit from the Playlist, and then press the
ENTER or √ button.
The Edit Playlist menu is displayed: Play,
Rename, Edit Scene, Copy, Delete
Edit Playlist
DVD-RAM(VR)
No.
Title
Length Edit
01 JAN/01/2006 12:00 00:00:03 √
02 JAN/01/2006 12:30 00:00:25 √
Play
03 Dolphin
00:00:05 √
Rename
Edit Playlist
Title
RETURN
DVD-Recorder
Edit Scene
Dolphin
1 Scene
JAN/01/2006 12:00 AM
DVD-RAM(VR)
No.
ENTER
Copy
Delete
Length Edit
01 JAN/01/2006 12:00 00:00:03 √
MOVE
ENTER
RETURN
EXIT
02 JAN/01/2006 12:30 00:00:25 √
03 Dolphin
00:00:05 √
MOVE
ENTER
RETURN
EXIT
3
Press the …† buttons to select Edit Scene, then
press the ENTER or √ button.
The Edit Scene screen is displayed.
DVD-Recorder
Edit Scene
DVD-RAM(VR)
Scene No.
2/7
Playlist No.
3
Play
Modify
01 00:00:05
02 00:00:06
03 00:00:07
04 00:00:08
05 00:00:10
06 00:00:11
Move
Add
MOVE
ENTER
RETURN
Delete
EXIT
English - 81
Editing
Dolphin
1 Scene
JAN/01/2006 12:00 AM
00995J(00)_VR330_AFS-Eng2
2006.4.13
7:6 PM
Page 82
6
Playing a Selected Scene
4
Press the …†œ √ buttons to select the scene
you want to play, then press the ENTER button.
The playlist title to be played is selected.
DVD-Recorder
Press the ENTER button at the start point of the
scene.
DVD-Recorder
Modify Scene
DVD-RAM(VR)
Scene No. 001
Start
End
Edit Scene
Title List : 1/31
DVD-RAM(VR)
Scene No.
2 / 17
Playlist No.
3
00:00:04
00:00:00
00:00:04
√
Play
Start
End
Change
Cancel
Modify
01 00:00:05
02 00:00:06
03 00:00:07
MOVE
Move
ENTER
RETURN
EXIT
Add
04 00:00:08
05 00:00:10
MOVE
5
ENTER
06 00:00:11
RETURN
• The image and starting point time are displayed
on the Start window.
• Select the starting or ending point of the section
you want to modify using the playback related
buttons (√II,Iœœ,√√I,œœ,√√).
Delete
EXIT
Press the ENTER button.
The selected scene will be played back.
– RAM
√
VR
7
LP
Press the ENTER button at the end point of the
scene.
DVD-Recorder
Modify Scene
DVD-RAM(VR)
Scene No. 001
Start
End
Title List : 1/31
• To stop scene play, press the STOP button.
Start
Modifying a Scene (Replacing a Scene)
DVD-Recorder
Playlist No.
3
Play
Modify
02 00:00:42
03 00:00:04
Editing
05 00:00:11
MOVE
8
ENTER
06 00:00:04
RETURN
DVD-Recorder
DVD-RAM(VR)
Scene No.
2/7
DVD-Recorder
EXIT
Modify Scene
DVD-RAM(VR)
Scene No. 001
Start
End
Title List : 1/31
00:00:00
00:00:00
00:00:00
√
End
MOVE
82 - English
Change
ENTER
Cancel
RETURN
Edit Scene
Playlist No.
EXIT
3
Play
Modify
01 00:00:03
02 00:00:42
03 00:00:04
04 00:00:03
05 00:00:11
06 00:00:04
Delete
Press the …† buttons to select Modify, then
press the ENTER button.
The Modify Scene screen is displayed.
Start
EXIT
Press the œ √ buttons to select Change, then
press the ENTER button.
Move
Add
MOVE
5
RETURN
Move
Add
04 00:00:03
ENTER
Cancel
Edit Scene
DVD-RAM(VR)
Scene No.
2/7
01 00:00:03
Change
• The image and ending point time are displayed
in the End window.
To setup, follow steps 1 to 3 in page 81.
Press the …† œ √ buttons to select the scene
you want to modify, then press the ENTER button.
00:00:10
00:00:10
End
MOVE
4
00:00:04
»
ENTER
RETURN
Delete
EXIT
• The scene you want to modify is changed with
the selected section.
00995J(00)_VR330_AFS-Eng3
2006.4.13
7:8 PM
Page 83
Moving a Scene (Changing the Position of a Scene)
Adding a Scene
To setup, follow steps 1 to 3 in page 81.
To setup, follow steps 1 to 3 in page 81.
4
Press the …† œ √ buttons to select the scene you
want to move (change the position), then press the
ENTER button.
DVD-Recorder
4
Edit Scene
DVD-RAM(VR)
Scene No.
1/7
Playlist No.
Press the …† œ √ buttons to select the scene
that will have a new scene inserted before it, then
press the ENTER button.
A yellow selection window is displayed on the
scene to be added as the new scene.
3
Play
DVD-Recorder
Modify
01 00:00:03
02 00:00:42
03 00:00:04
Edit Scene
DVD-RAM(VR)
Scene No.
3/3
Move
Playlist No.
04 00:00:03
MOVE
05 00:00:11
ENTER
06 00:00:04
RETURN
Modify
Delete
01 00:00:03
02 00:00:42
03 00:00:04
EXIT
Add
Press the …† buttons to select Move, then press the
ENTER button.
DVD-Recorder
Edit Scene
DVD-RAM(VR)
Scene No.
1/7
Playlist No.
Move
Delete
04 00:00:00
5
3
Play
Add
3
MOVE
5
Play
ENTER
RETURN
EXIT
Press the …† buttons to select Add, then press
the ENTER button.
The Add Scene screen is displayed.
Modify
01 00:00:03
02 00:00:42
03 00:00:04
DVD-Recorder
Move
04 00:00:03
MOVE
05 00:00:11
ENTER
06 00:00:04
RETURN
Add Scene
DVD-RAM(VR)
Add
Scene No. 001
Start
End
Delete
EXIT
Title List : 1/31
• A yellow selection window is displayed on the
scene to be moved.
6
DVD-Recorder
DVD-RAM(VR)
Scene No.
2/7
6
End
Add
ENTER
DVD-Recorder
3
EXIT
Add Scene
DVD-RAM(VR)
Scene No. 001
Start
End
Modify
02 00:00:42
03 00:00:04
04 00:00:03
05 00:00:11
06 00:00:04
Move
Add
MOVE
Edit Scene
3
Play
00:00:00
00:00:01
Start
EXIT
Playlist No.
00:00:01
√
End
Add
ENTER
Cancel
RETURN
EXIT
• The image and starting point time are displayed
in the Start window.
• Select the end point of the section where you
want to add the new scene using the playback
related buttons (√II,Iœœ,√√I,œœ,√√).
Modify
01 00:00:42
02 00:00:03
03 00:00:04
04 00:00:03
05 00:00:11
06 00:00:04
Move
Add
MOVE
■
Note
ENTER
RETURN
Delete
EXIT
Depending on the kind of disc, the displayed
screen may have a slight difference.
English - 83
Editing
RETURN
Title List : 1/31
Delete
• The selected scene is moved to the selected
position.
DVD-Recorder
DVD-RAM(VR)
Scene No.
2/7
RETURN
Edit Scene
Playlist No.
01 00:00:03
ENTER
Cancel
Press the ENTER button at the starting point of
the scene.
Play
MOVE
00:00:00
00:00:00
Start
MOVE
Press the …† œ √ buttons to select the position to
which you want to move the selected scene, then
select the ENTER button.
00:00:00
√
00995J(00)_VR330_AFS-Eng3
7
2006.4.13
7:8 PM
Page 84
Press the ENTER button at the end point of the
scene.
DVD-Recorder
Copying a Playlist Title to the VCR
Add Scene
DVD-RAM(VR)
1
Scene No. 001
Start
End
Title List : 1/31
00:00:01
Or use the MENU button.
• Press the MENU button with the disc stopped.
• Press the …† buttons to select Playlist, then
press the ENTER or √ button.
• Press the …† buttons to select Edit Playlist,
then press the ENTER or √ button.
00:00:03
00:00:03
»
Start
End
MOVE
Add
ENTER
Cancel
RETURN
EXIT
• The image and time of the end point are
displayed in the End window.
• To cancel, press the œ √ buttons to select
cancel and then press the ENTER button.
8
Press the PLAY LIST button with the disc stopped.
The Edit Playlist screen is displayed.
DVD-Recorder
Edit Playlist
DVD-RAM(VR)
No. Title
Length Edit
01 JAN/01/2006 12:00 00:00:11 √
02 JAN/01/2006 12:30 00:00:09 √
03 Dolphin
00:01:36 √
Press the …† buttons to select Add, then press
the ENTER button.
JAN/01/2006 12:00 AM
1 Scene
JAN/01/2006 12:00 AM
DVD-Recorder
DVD-RAM(VR)
Scene No.
1/4
Edit Scene
MOVE
Playlist No.
ENTER
RETURN
EXIT
3
Play
Modify
01 00:00:03
02 00:00:42
04 00:00:03
05 00:00:00
03 00:00:04
2
Move
Add
MOVE
ENTER
Delete
RETURN
EXIT
• The section you want to add is inserted prior to
the scene selected in step 4.
Press the …† buttons to select the title you want
to copy to the VCR, and then press the ENTER or
√ button.
The Edit Playlist menu is displayed: Play,
Rename, Edit Scene, Copy, Delete.
DVD-Recorder
Edit Playlist
DVD-RAM(VR)
No. Title
Deleting a Scene
To setup, follow steps 1 to 3 in page 81.
Dolphin
Edit Scene
2 Scene
Copy
JAN/01/2006 12:00 AM
4
Press the …† œ √ buttons to select the scene
you want to delete, and then press the ENTER
button.
DVD-Recorder
Edit Scene
DVD-RAM(VR)
Scene No.
4/4
Length Edit
01 JAN/01/2006 12:00 00:00:11 √
02 JAN/01/2006 12:30 00:00:09 √
Play
03 Dolphin
00:01:36 √
Rename
Playlist No.
MOVE
3
3
Play
Delete
ENTER
RETURN
EXIT
Press the …† buttons to select Copy, then press
the ENTER button.
• The title you choose is played and copied to
VCR tape.
Modify
Editing
01 00:00:03
02 00:00:42
03 00:00:04
DVD-Recorder
Move
Edit Playlist
DVD-RAM(VR)
Add
No. Title
04 00:00:03
MOVE
5
Delete
05 00:00:00
ENTER
RETURN
EXIT
Press the …† buttons to select Delete, then
press the ENTER button.
DVD-Recorder
Playlist No.
Play
Modify
01 00:00:03
02 00:00:42
04 00:00:03
05 00:00:00
Edit Scene
2 Scene
Copy
JAN/01/2006 12:00 AM
MOVE
03 00:00:04
3
4
Delete
ENTER
RETURN
EXIT
ENTER
The playlist can contain up to 99 playlist
Delete
RETURN
Press the MENU button after the operation has
finished. The menu screen will disappear.
Move
Add
84 - English
Dolphin
Edit Scene
DVD-RAM(VR)
Scene No.
4/3
MOVE
Length Edit
01 JAN/01/2006 12:00 00:00:11 √
02 JAN/01/2006 12:30 00:00:09 √
Play
03 Dolphin
00:01:36 √
Rename
EXIT
Note
titles.
00995J(00)_VR330_AFS-Eng3
2006.4.13
7:8 PM
Page 85
Deleting a Playlist Title from the
Playlist
1
4
Press the PLAY LIST button with the disc stopped.
The Edit Playlist screen is displayed.
DVD-Recorder
Edit Playlist
DVD-RAM(VR)
Or use the MENU button.
• Press the MENU button with the disc stopped.
• Press the …† buttons to select Playlist, then
press the ENTER or √ button.
• Press the …† buttons to select Edit Playlist,
then press the ENTER or √ button.
DVD-Recorder
Press the œ √ buttons to select Yes, then press
the ENTER button.
It automatically returned to the Edit Playlist screen
after the delete operation has finished.
Deleting...
(Please wait)
Dolphin
2 Scene
JAN/01/2006 12:00 AM
MOVE
ENTER
DVD-Recorder
Edit Playlist
No. Title
Edit Playlist
No. Title
Length Edit
Length Edit
01 JAN/01/2006 12:00 00:00:11 √
02 JAN/01/2006 12:30 00:00:09 √
01 JAN/01/2006 12:00 00:00:11 √
02 JAN/01/2006 12:30 00:00:09 √
03 Dolphin
00:01:36 √
JAN/01/2006 12:00 AM
JAN/01/2006 12:00 AM
3 Scene
1 Scene
JAN/01/2006 12:00 AM
JAN/01/2006 12:00 AM
2
EXIT
DVD-RAM(VR)
DVD-RAM(VR)
MOVE
RETURN
ENTER
RETURN
Press the …† buttons to select the title you want
to delete from the Playlist, then press the ENTER
or √ button.
The Edit Playlist menu is displayed: Play,
Rename, Edit Scene, Copy, Delete
DVD-Recorder
MOVE
EXIT
ENTER
RETURN
EXIT
Disc Manager
Edit Playlist
DVD-RAM(VR)
No. Title
Length Edit
01 JAN/01/2006 12:00 00:00:11 √
02 JAN/01/2006 12:30 00:00:09 √
Play
03 Dolphin
00:01:36 √
Rename
Dolphin
Edit Scene
2 Scene
Copy
JAN/01/2006 12:00 AM
Delete
MOVE
RETURN
Follow these instructions to give a name to a disc.
EXIT
Press the …† buttons to select Delete, then
press the ENTER button.
• You will be prompted with the delete confirmation
message ‘Do you want to delete?’.
1
With the unit in Stop mode, press the MENU
button.
DVD-Recorder
Title List
DVD-Recorder
Edit Playlist
Title List
DVD-RAM(VR)
Title List
√
Playlist
Disc Manager
DVD-RAM(VR)
Timer Rec.
Setup
Do you want to delete?
Copy
MOVE
Dolphin
Yes
ENTER
RETURN
EXIT
No
2 Scene
JAN/01/2006 12:00 AM
MOVE
ENTER
RETURN
EXIT
English - 85
Editing
3
ENTER
Editing the Disc Name
00995J(00)_VR330_AFS-Eng3
2
2006.4.13
7:9 PM
Page 86
Press the …† buttons to select Disc Manager,
then press the ENTER or √ button.
DVD-Recorder
Disc Manager
Disc Protection
Disc Protect allows you to protect your discs from being
formatted or deleted due to unintended operations.
DVD-RAM(VR)
Title List
Disc Name
:
√
Playlist
Disc Protection
: Not Protected
√
Disc Manager
Disc Format
:
√
Timer Rec.
Delete All Title Lists
√
1
Setup
Copy
MOVE
ENTER
RETURN
With the unit in Stop mode, press the MENU
button.
EXIT
DVD-Recorder
Title List
DVD-RAM(VR)
3
Press the …† buttons to select Disc Name, then
press the ENTER or √ button.
The Edit Name screen is displayed.
Title List
Title List
√
Playlist
Disc Manager
Timer Rec.
DVD-Recorder
Setup
Rename
DVD-RAM(VR)
Copy
MOVE
2
Save
Back Space
MOVE
Space
ENTER
Delete
Clear
RETURN
ENTER
RETURN
EXIT
Press the …† buttons to select Disc Manager,
then press the ENTER or √ button.
EXIT
DVD-Recorder
Disc Manager
DVD-RAM(VR)
4
Enter the desired characters using the …† œ √
buttons.
DVD-Recorder
Title List
Disc Name
:
√
Playlist
Disc Protection
: Not Protected
√
:
√
Disc Manager Disc Format
Timer Rec.
Rename
DVD-RAM(VR)
Delete All Title Lists
Disc
Copy
MOVE
Save
Back Space
MOVE
Space
ENTER
Delete
3
Clear
RETURN
EXIT
• This function is the same as the Rename
function in renaming the title list. (See page 72.)
• The maximum number of characters that can be
entered is 31.
Title List
Disc Name
: Disc
√
Playlist
Disc Protection
: Not Protected
√
Disc Manager
Disc Format
:
√
Timer Rec.
Delete All Title Lists
√
Copy
Title List
Disc Name
:
√
Playlist
Disc Protection
Protected
:Not
Protected
:Protected
√
Disc Manager Disc Format
Editing
Delete All Title Lists
√
√
Setup
Copy
MOVE
4
ENTER
RETURN
EXIT
Press the …† button to select Protected, then
press the ENTER or √ button.
DVD-Recorder
ENTER
RETURN
EXIT
Disc Manager
Title List
Disc Name
:
√
Playlist
Disc Protection
: Protected
√
:
√
Disc Manager Disc Format
Timer Rec.
You may need to clear disc protection before
beginning editing. (see page 86)
Depending on the kind of disc, the displayed
screen may be different.
86 - English
Disc Manager
DVD-RAM(VR)
DVD-RAM(VR)
Setup
Note
EXIT
Disc Manager
DVD-RAM(VR)
MOVE
RETURN
DVD-Recorder
Press the …† œ √ buttons to select Save, then
press the ENTER button.
A disc name is given to the disc.
DVD-Recorder
ENTER
Press the …† buttons to select Disc Protection,
then press the ENTER or √ button.
Timer Rec.
5
√
Setup
Delete All Title Lists
√
Setup
Copy
MOVE
ENTER
RETURN
EXIT
00995J(00)_VR330_AFS-Eng3
2006.4.13
7:9 PM
Page 87
Formatting a Disc
Use these instructions to format a disc. Clear disc
protection before formatting.
DVD-RW
• You will be prompted with the confirmation
message ‘Choose the recording format for
DVD-RW.’
DVD-Recorder
Disc Manager
DVD-RW(VR)
1
With the unit in Stop mode, press the MENU
button.
DVD-Recorder
Title List
Title List
Disc Name
:
√
Playlist
Disc Protection
: Not Protected
√
Disc Format
: DVD-VR
Disc Manager
Choose the recording format for DVD-RW.
Disc Finalize
Timer Rec.
Delete
All Title Lists DVD-V
DVD-VR
Setup
DVD-RAM(VR)
Title List
Title List
√
√
√
√
Copy
Playlist
MOVE
ENTER
RETURN
EXIT
Disc Manager
Timer Rec.
Setup
Copy
MOVE
2
ENTER
RETURN
EXIT
4
DVD-VR and DVD-V modes are compatible
with the following disc types.
Press the …† buttons to select Disc Manager,
then press the ENTER or √ button.
DVD-Recorder
Press the œ √ buttons to select Yes, then press
the ENTER button. The disc is formatted.
DVD-VR
DVD-V
DVD-RAM
DVD-RW
DVD-RW
DVD-R
Disc Manager
DVD-RAM(VR)
Title List
Disc Name
:
√
Playlist
Disc Protection
: Not Protected
√
Disc Manager
Disc Format
:
√
Timer Rec.
Delete All Title Lists
DISC
√
Setup
Copy
MOVE
3
ENTER
RETURN
EXIT
Press the …† buttons to select Disc Format,
then press the ENTER or √ button.
DVD-Recorder
Finalizing a disc
After you record titles onto a DVD-RW/DVD±R disc with
your DVD Recorder & VCR, it needs to be finalized
before it can be played back on external devices.
Disc Manager
DVD-RAM(VR)
Title List
Disc Name
:
√
Playlist
Disc Protection
: Not Protected
√
Disc Manager
Disc Format
:
√
Timer Rec.
Delete All Title Lists
√
Setup
1
With the unit in Stop mode, press the MENU
button.
Copy
MOVE
ENTER
RETURN
EXIT
DVD-Recorder
Title List
DVD-RW(VR)
Title List
Title List
√
Playlist
Disc Manager
Timer Rec.
Setup
DVD-Recorder
Disc Manager
Copy
DVD-RAM(VR)
Title List
Disc Name
:
√
Playlist
Disc Protection
: Not Protected
√
Format
:
Disc Manager Disc
Do you want to format disc?
Delete All Title Lists
Timer Rec.
Setup
Yes
MOVE
ENTER
RETURN
EXIT
√
√
No
Copy
MOVE
ENTER
RETURN
EXIT
• You will be prompted with the confirmation
message 'All data will be deleted. Do you want
to continue?'.
English - 87
Editing
DVD-RAM/+RW
• You will be prompted with the confirmation
message 'Do you want to format disc?'.
00995J(00)_VR330_AFS-Eng3
2
2006.4.13
7:9 PM
Page 88
Press the …† buttons to select Disc Manager,
then press the ENTER or √ button.
DVD-Recorder
4
Press the œ √ buttons to select Yes, then press the
ENTER button.
The disc is finalized.
Disc Manager
DVD-RW(VR)
Title List
Disc Name
:
√
Playlist
Disc Protection
: Not Protected
√
Disc Manager
Disc Format
: DVD-VR
√
Timer Rec.
Disc Finalize
√
Delete All Title Lists
√
Setup
Once a disc is finalized, you cannot delete
Note
is finalized, it is playable in a standard DVD
player.
Copy
MOVE
ENTER
RETURN
titles from the record list.
Once a DVD±R/DVD-RW (video mode)disc
EXIT
Depending on the disc type, the displayed
screen may be different.
3
Press the …† button to select Disc Finalize, then
press the ENTER or √ button.
Finalizing time may be different depending
on the amount of data recorded on the disc.
Data on the disc will be damaged if the
DVD-Recorder
Disc Manager
recorder is powered off during finalize
process.
DVD-RW(VR)
Title List
Disc Name
:
√
Playlist
Disc Protection
: Not Protected
√
Disc Manager
Disc Format
: DVD-VR
√
Timer Rec.
Disc Finalize
√
Delete All Title Lists
√
Setup
Unfinalizing a disc (V/VR mode)
Copy
MOVE
ENTER
RETURN
DVD-Recorder
EXIT
Disc Manager
DVD-R(V)
Title List
Disc Name
:
√
Disc Manager
Disc Protection
: Not Protected
√
Timer Rec.
Disc Finalize
√
Setup
Delete All Title Lists
√
1
With the unit in Stop mode, press the MENU
button.
DVD-Recorder
Title List
DVD-RW(VR:F)
Title List
Copy
Title List
√
Playlist
Disc Manager
MOVE
ENTER
RETURN
EXIT
Timer Rec.
Setup
You will be prompted with the message 'Do you
want to finalize disc?'.
DVD-Recorder
Editing
MOVE
ENTER
RETURN
EXIT
Disc Manager
DVD-RW(VR)
Title List
Disc Name
:
√
Playlist
Disc Protection
: Not Protected
√
: DVD-VR
Disc Manager Disc Format
Do you want to finalize disc?
Disc Finalize
Timer Rec.
Delete Yes
All Title Lists No
Setup
ENTER
RETURN
2
Press the …† buttons to select Disc Manager,
then press the ENTER or √ button.
√
√
DVD-Recorder
√
DVD-RW(VR:F)
Copy
MOVE
Copy
EXIT
Disc Manager
Title List
Disc Name
:
√
Playlist
Disc Format
: DVD-VR
√
Disc Manager
Disc Unfinalize
√
Timer Rec.
If you select Yes, you will be prompted again with
the message 'Disc will be finalized. Do you want
to continue?'
DVD-Recorder
Setup
Copy
MOVE
ENTER
RETURN
EXIT
Disc Manager
DVD-Recorder
DVD-RW(VR)
Title List
Disc Name
:
√
Playlist
Disc Protection
: Not Protected
√
: DVD-VR
Disc will be finalized.
Disc Manager Disc Format
you want to continue?
DiscDo
Finalize
Timer Rec.
Delete Yes
All Title Lists No
Setup
√
Disc Manager
DVD-Video(RW)
Title Menu
Disc Format
Disc Menu
Disc Unfinalize
√
Disc Manager
√
Timer Rec.
: DVD-V
√
√
Setup
Copy
Copy
MOVE
ENTER
RETURN
EXIT
MOVE
88 - English
ENTER
RETURN
EXIT
00995J(00)_VR330_AFS-Eng3
3
2006.4.13
7:9 PM
Page 89
Press the …† button to select Disc Unfinalize,
then press the ENTER or √ button.
You will be prompted with the message 'Do you
want to unfinalize disc?'.
DVD-Recorder
1
Disc Manager
DVD-RW(VR:F)
Title List
Disc Name
:
√
Playlist
Disc Format
: DVD-VR
√
Disc Manager Disc Unfinalize
Do you want to unfinalize disc?
Timer Rec.
Setup
Delete All Title Lists
With the unit in Stop mode, press the MENU
button.
DVD-Recorder
Title List
DVD-RAM(VR)
√
Title List
Title List
√
Playlist
Yes
No
ENTER
RETURN
Disc Manager
Copy
MOVE
Timer Rec.
EXIT
Setup
Copy
If you select Yes, you will be prompted again with
the message 'Disc will be unfinalized. Do you
want to continue?'
DVD-Recorder
MOVE
2
Disc Manager
ENTER
RETURN
EXIT
Press the …† buttons to select Disc Manager,
then press the ENTER or √ button.
DVD-RW(VR:F)
Title List
Disc Name
:
√
Playlist
Disc Format
: DVD-VR
√
Unfinalize
will be unfinalized.
Disc Manager DiscDisc
Do you want to continue?
Timer Rec.
Setup
Yes
DVD-Recorder
Title List
Disc Name
:
√
Playlist
Disc Protection
: Not Protected
√
Disc Manager
Disc Format
:
√
No
Copy
MOVE
Timer Rec.
ENTER
RETURN
Disc Manager
DVD-RAM(VR)
√
EXIT
Delete All Title Lists
√
Setup
Copy
MOVE
4
Press the œ √ buttons to select Yes, then press
the ENTER button.
The disc is unfinalized.
■
Note
A DVD-RW can be finalized or unfinalized in
Video mode.
Mark
Finalize
DVD-Video(RW)
Operation Same as DVD-Video
Unfinalize
DVD-RW(V)
Additional recording, protection
and deletion are possible.
3
ENTER
DVD-Recorder
Finalize
Disc Manager
DVD-RAM(VR)
Title List
Disc Name
:
√
Playlist
Disc Protection
: Not Protected
√
:
√
Disc Manager Disc Format
Timer Rec.
Delete All Title Lists
√
Setup
Copy
ENTER
RETURN
EXIT
• You will be prompted with the confirmation message 'Do you want to delete all title lists?'.
Unfinalize
DVD-Recorder
Disc Manager
DVD-RAM(VR)
Mark
Operation
DVD-RW(VR:F)
Additional recording,
deletion, editing, and
protection are impossible.
DVD-RW(VR)
Additional recording,
deletion, editing, and
protection are possible.
Title List
Disc Name
:
√
Playlist
Disc Protection
: Not Protected
√
Format
:
Disc Manager Disc
Do you want to delete all title lists?
Delete All Title Lists
Timer Rec.
Yes
No
Setup
√
√
Copy
MOVE
ENTER
RETURN
EXIT
English - 89
Editing
A DVD-RW can be finalized or unfinalized in
VR mode.
EXIT
Press the …† button to select Delete All Title
Lists, then press the ENTER or √ button.
MOVE
■
RETURN
00995J(00)_VR330_AFS-Eng3
2006.4.13
7:9 PM
Page 90
• When Protected Title exists: The Delete All Title
List function will not operate. If there is a title
containing a still picture, however, that function
will not operate.
If you want to delete a protected title, disable
Protect for it on the Lock item.
3
Press the …† buttons to select Edit Compatible,
then press the ENTER or √ button.
DVD-Recorder
Disc Manager
DVD+RW
Title List
Disc Name
Disc Manager
Disc Format
√
Timer Rec.
Edit Compatible
√
:
√
Setup
4
Press the œ √ buttons to select Yes, then press
the ENTER button.
All title lists are deleted.
Copy
MOVE
ENTER
RETURN
DVD-Recorder
EXIT
Disc Manager
DVD+RW
Title List
Edit Compatible
For DVD+RW discs, this function needs to be performed
in order to view edited chapters or titles on a standard
DVD player.
1
Title List
DVD+RW
Title List
Title List
√
Disc Manager
Setup
Copy
MOVE
ENTER
RETURN
EXIT
Press the …† buttons to select Disc Manager,
then press the ENTER or √ button.
DVD-Recorder
Disc Manager
Editing
DVD+RW
Title List
Disc Name
Disc Manager
Disc Format
√
Timer Rec.
Edit Compatible
√
:
√
Setup
Copy
MOVE
90 - English
:
ENTER
RETURN
√
√
√
EXIT
• You will be prompted with the confirmation message 'Do you want to execute Edit compatible?
This may take more than an hour depending on
the configuration.'.
4
Press the œ √ buttons to select Yes, then press
the ENTER button to execute the edit compatible.
After performing this function, you can go to
TITLE MENU screen directly by pressing the
TITLE MENU button.
Timer Rec.
2
MOVE
With the unit in Stop mode, press the MENU
button.
DVD-Recorder
Disc Name
Disc Manager Disc Format
Do you want to execute Edit compatible?
Edit Compatible
Timer Rec. This
may take more than an hour
depending on the configuration.
Setup
Yes
No
Copy
ENTER
RETURN
EXIT
00995J(00)_VR330_AFS-Eng3
2006.4.13
7:9 PM
Page 91
Reference
Troubleshooting
†
Specifications
Troubleshooting
(DVD-VIDEO/DVD-RAM/DVD±RW/DVD±R) .................92
Troubleshooting (DVD) .....................................................93
LIMITED WARRANTY TO ORIGINAL
PURCHASER
Troubleshooting (VCR)......................................................94
Problems and Solutions (Display error Message).............95
Specifications ....................................................................97
English - 91
Reference
†
00995J(00)_VR330_AFS-Eng3
2006.4.13
7:9 PM
Page 92
Troubleshooting
(DVD-VIDEO/DVD-RAM/DVD±RW/DVD±R)
If your product malfunctions, go through the check points below before contacting a Samsung authorized service center,
Reference
Problem
Explanation/Solution
No power.
• Check whether the power cord is securely plugged into the power outlet.
• Did you press the power button of your DVD Recorder & VCR.
The input is displayed
for a while when the
power turns on.
• The DVD Recorder & VCR requires some time to initialize after it is turned on.
If Quick recording function is set to on, the DVD Recorder & VCR will power on quickly,
which enables you to immediately record a desired channel. (See page 42.)
Cannot record TV
programs.
• Check whether the power cord is securely plugged into the power outlet.
• Did you set the DVD Recorder & VCR channel settings correctly?
• Check the free space on your DVD-RAM/DVD±RW/DVD±R disc.
• Check the antenna cable is connected.
Timer recording does
not work properly.
• Check the recording time, end time and current time settings again.
• Recording will be cancelled if the power is interrupted due to a power
failure or other reason during recording.
Cannot record.
• Check whether the disc is formatted. This product can record on
formatted discs only. (See page 87.)
• Check whether your DVD-RAM/DVD±RW/DVD±R disc has a sufficient free space.
I pressed the REC
button but there is
no response.
• Recording is available on DVD-RAM/DVD±RW/DVD±R discs only.
• If a program is copy protected, you cannot record it.
I forget the password
for parental lock.
• Press and hold the CH ( / ) button on the front panel of your unit for more than 5
seconds with no disc, and then press the POWER OFF/ON button. All settings including
password will revert to factory settings. Do not use it if not absolutely required.
(Note that this function is available only when there is no disc inserted.)
Cannot play the disc.
• Check whether the disc is inserted correctly with the label facing up.
• Check the regional code of your DVD disc.
• This DVD Recorder & VCR cannot playback some types of disc. (See page 5.)
No sound.
• Are you watching a program in slow or skip mode?
If you are playing a program at a speed other than normal speed, sound
is not output. (Except for forward search Playback (Fast1))
• Check the connections and initial settings.
• Check whether the disc is damaged.
Clean up the disc, if necessary.
• Check whether the disc is inserted correctly with the label facing up.
92 - English
00995J(00)_VR330_AFS-Eng3
2006.4.13
7:9 PM
Page 93
Troubleshooting (DVD)
Problem
Explanation/Solution
You cannot use the operation or function due to one of the following reasons:
(1) Your DVD disc does not support the feature (for example, angles)
(2) You've requested a title, chapter, or scan time that is out of the correct range.
Play mode settings are
different from the settings configured with
the Setting menu.
The disc does not support all the selected functions.
In this case, some settings you configure on the Setting menu may not work properly.
Cannot change the
aspect ratio.
Aspect ratio is fixed for DVD disc.
No audio output.
Check whether you selected correct digital output options in the Audio Output Options menu.
No video or audio output.
The disc tray is ejected
after 2 to 5 seconds.
Did you move your DVD Recorder & VCR suddenly from a cold place to a warm place?
In this case, do not connect the plug to the power outlet and wait for two hours. Then insert
the disc and try to play back again. It will work properly when condensation has evaporated.
Angle operation does not
work during playback of a
DVD disc.
Angle operation is available only when the disc contains images captured at different
angles.
The disc revolves, but
no image or bad quality images are output.
• Check whether there is damage or foreign materials on your disc.
• Some discs with bad manufacturing quality may not be played back.
• If the scene changes from dark to bright suddenly, the screen may jitter temporarily,
but it is not a defect.
Desired sound
language and
subtitle language are
not played.
Sound languages and subtitle languages are disc-specific.
Only the sound and subtitle languages contained on a DVD disc are available and displayed
on the disc menu.
No progressive
output.
• Check whether PS is displayed on front panel.
• Make sure to change the component video output using the Progressive button when the
disc is stopped.
The remote control
doesn't work.
• Point the remote control at the remote control sensor on your DVD Recorder & VCR.
Operate within distance. (15ft)
Remove obstacles between your DVD Recorder & VCR and remote control.
• Check whether the batteries are depleted.
Other problems
• Read the table of contents and then find and read the sections describing your problem,
and follow the directions given.
• Turn the unit off and on.
• If your problem still persists, contact your nearest Samsung service center.
English - 93
Reference
icon appears on
the screen.
00995J(00)_VR330_AFS-Eng3
2006.4.13
7:9 PM
Page 94
Troubleshooting (VCR)
Before contacting a Samsung authorized service center, perform the following simple checks.
Problem
Explanation/Solution
No power
• Check that the power plug is connected to a wall outlet.
• Have you pressed the POWER button?
You cannot insert a video cassette
• A video cassette can only be inserted with the window side up and
the safety tab facing you.
The television program was not recorded
• Check the DVD Recorder & VCR antenna connections.
• Is the DVD Recorder & VCR tuner properly set?
• Check if the safety tab is intact on the cassette.
Timer recording was unsuccessful
• Re-check the recording start/stop time settings and the current time
• Check whether you insert a tape which has enough time record
No playback picture or the picture
is distorted
• Check to see if you are using a prerecorded tape.
You cannot see normal broadcasts
Noise bars or streaks on playback
• Check the tuner/external setting. It should be on tuner.
• Check the TV antenna connections.
• Press the CH/TRK ( / ) buttons to minimize this effect.
When the √II button is pressed
during playback, the still picture
has severe “noise bar” streaks
• A still picture may have “noise bars”, depending on the
condition of the tape. Press the CH/TRK ( / ) buttons
during slow motion to minimize this effect.
Video Head Cleaning
• If poor pictures appear on a variety of cassettes, the video
heads may need cleaning. This is not a common problem
and unless it appears, the heads should not be cleaned.
When cleaning the video heads, read all instructions
provided with the head cleaning cassette. Incorrect head
cleaning can permanently damage the video heads.
Reference
If you are unable to solve the problem after reading the above instructions, note:
• The model and serial number on the rear of your DVD Recorder & VCR
• The warranty information
• A clear description of the problem
Then contact your nearest SAMSUNG authorized service center.
94 - English
00995J(00)_VR330_AFS-Eng3
2006.4.13
7:9 PM
Page 95
Problems and Solutions
(Display error Message)
Before contacting a Samsung authorized service center, perform the following simple checks.
Problem
You cannot record a copy protected movie.
Explanation / Solution
• You can’t record the video since it is protected by copyright.
You cannot record. This disc is protected.
This disc cannot be formatted (the disc is
protected).
This disc cannot be renamed
(the disc is protected).
This disc cannot be finalized (the disc is
protected).
• Disc you are using is protected. To record on this disc or use
this function, cancel the disc protection function. Refer to
page 85.
This [Menu] is not available (the disc is
protected).
The disc cannot be played,
Please check the regional code of the disc.
• The disc does not match the regional code for your area and
cannot be played on this device.
This disc cannot be formatted.
Please check the disc.
You could not format the disc
because of error detection.
You could not finalize the disc
because of error detection.
• Make sure there are no scratches or dirt on the disc.
You could not unfinalize the disc
because of error detection.
The disc cannot be played,
Please check the TV system.
• The disc is PAL format and cannot be played on this unit.
The disc can be neither played nor recorded.
• Make sure there are no scratches or dirt on the disc.
If the disc has invalid information,
no more titles can be recorded.
Please format the disc beforehand.
• You can’t use the disc because it contains errors from
previous recordings.
Use the disc after formatting.
English - 95
Reference
The disc cannot be played, Please check the
disc.
00995J(00)_VR330_AFS-Eng3
2006.4.13
7:9 PM
Page 96
Problems and Solutions
(Display error Message)
Problem
Explanation / Solution
Error is detected on the disc.
• You can’t use the disc because it contains errors from
previous recordings.
Use the disc after formatting.
System error is found.
Please try it again after turning off the power.
• When operating, errors happen. Turn off the device.
(To turn off, press and hold the power button on the front of
the device for 10 seconds.)
After turning off, press the Open button and remove the disc
from the device.
The DV device is not connected.
• Make sure the DV device is connected properly to the DV
connection Jack.
If it is connected properly, turn it off and on once again.
If you are unable to solve the problem after reading the above instructions, note:
• The model and serial number on the rear of your DVD Recorder & VCR
• The warranty information
• A clear description of the problem
Reference
Then contact your nearest SAMSUNG authorized service center. Call 1-800-SAMSUNG for a center near you.
96 - English
00995J(00)_VR330_AFS-Eng3
2006.4.13
7:9 PM
Page 97
Specifications
General
Power requirements
~100-240V, 60Hz
Power consumption
28 Watts
Weight
8.75 lb
Dimensions
16.9 in(W) x 10.6 in(D) x 3.1 in(H)
Operating temp.
+41°F to +95°F
Other conditions
Keep level when operating. Less than 75% operating humidity
Video
1.0 V p-p at 75Ω load, sync negative
S-Video input (Y: 1.0Vp-p, C: 0.286Vp-p at 75Ω load)
Input
Max. Audio Input Level
2Vrms
DV Input
IEEE 1394(4p) compatible jack
Receivable Channels
Regular TV broadcasting: VHF (2~13), UHF (14~69)
Cable TV broadcasting: 1~125
Audio
Audio output jacks 1, 2
Optical/Coaxial digital audio output support
Min. 100 dB signal-to-noise ratio
Max. 0.005% total harmonic distortion (T.H.D)
Output
at average 1 KHz
Video
Video output jacks 1
S-Video output 1 (Y:1.0Vp-p, C:0.286Vp-p at 75Ω load)
Component output
(Y: 1.0Vp-p, Pb: 0.70Vp-p, Pr: 0.70Vp-p at 75Ω load)
Picture Compression format
MPEG-II
Audio Compression format
Dolby AC-3 256kbps
Recording Quality
XP (about 8 Mbps), SP (about 4 Mbps), LP (about 2 Mbps),
DVD
EP (about 1.2 Mbps)
Video S/N Ratio
Min. 50dB at standard recording
Audio S/N Ratio
Min. 75dB
Audio frequency characteristics
20 Hz ~ 20 KHz
Audio Output
For DVD discs, audio signals recorded at 96kHz sampling frequency are converted into and output at 48kHz.
DVD
AUDIO CD(CD-DA)
48 / 96KHz
44.1KHz
Digital Audio Output
48KHz
44.1KHz
English - 97
Reference
Disc Type
Analog Audio Output
00995J(00)_VR330_AFS-Eng3
2006.4.13
7:9 PM
Page 98
SAMSUNG DVD RECORDER & VCR
LIMITED WARRANTY TO ORIGINAL PURCHASER
This SAMSUNG brand product, as supplied and distributed by Samsung Electronics America, Inc. (SAMSUNG)
and delivered new, in the original carton to the original consumer purchaser, is warranted by SAMSUNG against
manufacturing defects in materials and workmanship for a limited warranty period of:
One (1) Year Parts / Ninety (90) days Labor
(90 days Parts and Labor for Commercial Use)
This limited warranty begins on the original date of purchase, and is valid only on products purchased and used
in the United States. To receive warranty service, the purchaser must contact SAMSUNG for problem determination and service procedures. Warranty service can only be performed by a SAMSUNG authorized service center.
The original dated bill of sale must be presented upon request as proof of purchase to SAMSUNG or
SAMSUNG’s authorized service center. Transportation of the product to and from the service center is the
responsibility of the purchaser.
SAMSUNG will repair or replace this product, at our option and at no charge as stipulated herein, with new or
reconditioned parts or products if found to be defective during the limited warranty period specified above. All
replaced parts and products become the property of SAMSUNG and must be returned to SAMSUNG.
Replacement parts and products assume the remaining original warranty, or ninety (90) days, whichever is
longer.
SAMSUNG ís obligations with respect to software products distributed by SAMSUNG under the SAMSUNG
brand name are set forth in the applicable end user license agreement. Non-SAMSUNG hardware and software
products, if provided, are on an ”AS IS” basis. Non-SAMSUNG manufacturers, suppliers, publishers, and service
providers may provide their own warranties.
This limited warranty covers manufacturing defects in materials and workmanship encountered in normal, and
except to the extent otherwise expressly provided for in this statement, noncommercial use of this product, and
shall not apply to the following, including, but not limited to: damage which occurs in shipment; delivery and
installation; applications and uses for which this product was not intended; altered product or serial numbers;
cosmetic damage or exterior finish; accidents, abuse, neglect, fire, water, lightning or other acts of nature; use of
products, equipment, systems, utilities, services, parts, supplies, accessories, applications, installations, repairs,
external wiring or connectors not supplied and authorized by SAMSUNG, or which damage this product or result
in service problems; incorrect electrical line voltage, fluctuations and surges; customer adjustments and failure to
follow operating instructions, cleaning, maintenance and environmental instructions that are covered and prescribed in the instruction book; product removal or reinstallation; reception problems and distortion related to
noise, echo, interference or other signal transmission and delivery problems. SAMSUNG does not warrant uninterrupted or error-free operation of the product.
THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE LISTED AND DESCRIBED ABOVE, AND NO WARRANTIES WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, SHALL APPLY AFTER THE EXPRESS WARRANTY PERIODS STATED ABOVE, AND NO OTHER EXPRESS WARRANTY OR GUARANTY GIVEN BY ANY PERSON, FIRM OR CORPORATION WITH RESPECT TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG. SAMSUNG SHALL NOT BE LIABLE FOR LOSS OF REVENUE OR PROFITS, FAILURE TO REALIZE SAVINGS OR
OTHER BENEFITS, OR ANY OTHER SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE
USE, MISUSE OR INABILITY TO USE THIS PRODUCT, REGARDLESS OF THE LEGAL THEORY ON WHICH THE
CLAIM IS BASED, AND EVEN IF SAMSUNG HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
NOR SHALL RECOVERY OF ANY KIND AGAINST SAMSUNG BE GREATER IN AMOUNT THAN THE PURCHASE
PRICE OF THE PRODUCT SOLD BY SAMSUNG AND CAUSING THE ALLEGED DAMAGE. WITHOUT LIMITING
THE FOREGOING, PURCHASER ASSUMES ALL RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO PURCHASER AND PURCHASERíS PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF THE USE,
MISUSE OR INABILITY TO USE THIS PRODUCT SOLD BY SAMSUNG NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF SAMSUNG. THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS PRODUCT, IS NONTRANSFERABLE AND STATES YOUR EXCLUSIVE REMEDY.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty
gives you specific legal rights, and you may also have other rights which vary from state to state.
To obtain warranty hardware service, please contact SAMSUNG at:
Samsung Electronics America, Inc.
105 Challenger Road Ridgefield Park, NJ 07660-0511
1-800-SAMSUNG (726-7864) and www.samsung.com
00995J(00)_VR330_AFS-Eng3
2006.4.13
7:9 PM
Page 99
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG
customer care centre.
Region
North America
Latin America
Europe
CIS
Country
CANADA
MEXICO
U.S.A
ARGENTINE
BRAZIL
CHILE
COSTA RICA
ECUADOR
EL SALVADOR
GUATEMALA
JAMAICA
PANAMA
PUERTO RICO
REP. DOMINICA
TRINIDAD & TOBAGO
VENEZUELA
BELGIUM
CZECH REPUBLIC
DENMARK
FINLAND
FRANCE
GERMANY
HUNGARY
ITALIA
LUXEMBURG
NETHERLANDS
NORWAY
POLAND
PORTUGAL
SLOVAKIA
SPAIN
SWEDEN
U.K
RUSSIA
UKRAINE
AUSTRALIA
CHINA
HONG KONG
INDIA
Asia Pacific
INDONESIA
JAPAN
MALAYSIA
PHILIPPINES
SINGAPORE
THAILAND
Middle East & Africa
TAIWAN
VIETNAM
SOUTH AFRICA
U.A.E
Customer Care Center ☎
1-800-SAMSUNG (7267864)
01-800-SAMSUNG (7267864)
1-800-SAMSUNG (7267864)
0800-333-3733
0800-124-421
800-726-7864(SAMSUNG)
0-800-507-7267
1-800-10-7267
800-6225
1-800-299-0013
1-800-234-7267
800-7267
1-800-682-3180
1-800-751-2676
1-800-7267-864
1-800-100-5303
02 201 2418
844 000 844
38 322 887
09 693 79 554
08 25 08 65 65 (0,15€/Min)
01805 - 121213 (€ 0,12/Min)
06 40 985 985
199 153 153
02 261 03 710
0900 20 200 88 (€ 0.10/Min)
231 627 22
0 801 801 881
80 8 200 128
0850 123 989
902 10 11 30
08 585 367 87
0870 242 0303
8-800-200-0400
8-800-502-0000
1300 362 603
800-810-5858, 010- 6475 1880
2862 6001
3030 8282
1600 1100 11
0800-112-8888
0120-327-527
1800-88-9999
1800-10-SAMSUNG (7267864)
1800-SAMSUNG (7267864)
1800-29-3232
02-689-3232
0800-329-999
1 800 588 889
0860 7267864 (SAMSUNG)
800SAMSUNG (7267864)
Web Site
www.samsung.com/ca
www.samsung.com/mx
www.samsung.com
www.samsung.com/ar
www.samsung.com/br
www.samsung.com/cl
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/be
www.samsung.com/cz
www.samsung.com/dk
www.samsung.com/fi
www.samsung.com/fr
www.samsung.de
www.samsung.com/hu
www.samsung.com/it
www.samsung.lu
www.samsung.com/nl
www.samsung.com/no
www.samsung.com/pl
www.samsung.com/pt
www.samsung.com/sk
www.samsung.com/es
www.samsung.com/se
www.samsung.com/uk
www.samsung.ru
www.samsung.com/ur
www.samsung.com/au
www.samsung.com.cn
www.samsung.com/hk
www.samsung.com/in
www.samsung.com/id
www.samsung.com/jp
www.samsung.com/my
www.samsung.com/ph
www.samsung.com/sg
www.samsung.com/th
www.samsung.com/tw
www.samsung.com/vn
www.samsung.com/za
www.samsung.com/mea
00995J(00)_VR330_AFS-Eng3
2006.4.13
7:9 PM
Page 100
SAMSUNG ELECTRONICS AMERICA, INC.
105 Challenger Road, Ridgefield Park,
N.J. 07660-0511
TEL: 1-800-SAMSUNG (726-7864)
English
AK68-00995J-00
Download PDF