简体中文
镜头
使用本产品前
使用说明书
更新相 机机身和镜头的固件。请访问 www.samsung.com 以下载
固件。
SAMSUNG 45mm F1.8 [T6] 2D/3D
拆开包装
此说明书专门为指导您了解镜头基本功能和特征而设计。
为保证安全、正确地使用,请仔细阅读此说明书。
镜头,镜头盖,镜头接口盖,遮光罩,镜头包,使用说明书
•另购项目:滤光镜
各部位名称(见图 A)
AD68-08121A (1.5)
A
1
2
6
4
1 镜头连接指示 2 对焦圈 3 镜头 4 i-Function 按钮
5 2D/3D 开关 6 镜头信息触点
连接和移除镜头
► 要安装镜头,
1卸下镜头盖、镜头接口盖和机身盖。
2将相机机身红色标记对准镜头红色标记。然后如图
所示旋转镜头,直到其锁定到位。(见图 B)
3
5
B
D
► 要
卸下镜头,按住镜头释放按钮,然后如图所示旋转镜头。
(见图 C)
使用对焦环
在 MF 模式中,可通过旋转镜头上的对焦环来手动调整对焦。
可以在相机上选择 MF 模式。
以 3D 模式拍摄(见图 D)
将镜头上的 2D/3D 开关置于 3D,然后拍摄距离拍摄对象
1.5-5 米的照片或视频。可以通过镜头拍摄 3D 照片或视频。
•除 B 以外,不管相机的模式旋钮处于什么位置,3D 模式
始终开启。
C
F
E
•仅可在支持 3D 功能的相机上使用 3D 模式。在 3D 模
式中,光圈值的设置约为 F6。
•以 3D 功能拍摄的相片将另存为 JPEG (2D) 和 MPO
(3D) 格式。在相机的显示屏上,仅可查看 JPEG 文
件。
•在低温中拍摄可能导致影像颜色失真并可能消耗更多电
池电量。
•在低于 8.5 LV/900 lux 的条件下可能无法正常拍摄。
为了获得最佳效果,请在光线充足的地方拍摄照片。
•拍摄显示屏、墨镜或偏光滤镜等包含偏光材料的对象
时,或在镜头上使用偏光材料时,影像可能会显得较
暗,或者可能无法正确应用 3D 效果。
•在 2D 模式中通过 3D 设置拍摄照片或视频所产生的
3D 效果可能不如在 3D 模式中所拍摄的效果显著。要
增强 3D 效果,请将 2D/3D 开关置于 3D。
•如果在拍摄时垂直旋转或倾斜相机,可能无法正确应用
3D 效果。使用相机以正常姿势拍摄影像。
•如果在荧光灯下拍摄或拍摄投影仪或电视上显示的影
像,由于闪烁效果,影像可能会显得较黑。
•不要长时间在 3D 电视或 3D 显示器查看用相机拍摄的
3D 图像。否则可能会造成不适症状,例如眼睛疲劳,
身体疲劳,恶心或其他。
•如果在观看 3D 照片或视频时觉得头晕或眼花,请立即
中止使用 3D 功能。如果问题仍然存在,请咨询健康专
家。
使用 i-Function
按下镜头上的 i-Function 按钮时,可以选择 E 以调
整景深或选择 Z 以放大拍摄对象。也可调整某些拍摄选
项。此功能仅在相机支持 i-Function 时可用。可用选项可能因
拍摄模式不同而各异。
1将模式旋钮旋转到 P、A、S、M 或 i。
2按镜头上的 [i-Function] 选择一个设置。
•可用设置可能因拍摄模式不同而异。
3旋转镜头上的对焦环来调整设置(或在 Z
模式中更改变焦率)。
使用镜头遮光罩(见图 E)
若要避免影像画质因不必要的光线遮挡而变差,请使用镜头罩。
在拍摄对象与相机之间距离较近的情况下使用闪光灯,
闪光灯光线可能会被镜头或镜头遮光罩部分遮挡。为确
保获得适当的光照,请卸下镜头遮光罩或调整相机和拍
摄对象之间的距离。
使用滤光镜(另购)(见图 F)
将滤光镜连接在镜头上之前,请确保滤光镜与镜头兼容。
关于兼容的滤光镜尺寸,请参考“规格”。
•使用滤镜时,使其远离灰尘、污垢或刮擦。另外,请勿
尝试同时安装两个或更多滤镜。否则可能会使图像画质
变差并导致虚光效果。
•如果使用广角镜头和较厚的滤光镜,影像可能会发暗。
规格
镜头名称
焦距
相当于 35 mm 的焦距
镜头结构-元件
镜头结构-组
查看角度
光圈叶片数
最小焦距(广角)
光圈叶片数
最小焦距
最大放大倍率
镜头遮光罩
光学图像稳定
接口类型
滤光片尺寸
最大直径
长度
重量(仅限镜头,近似值)
操作温度
操作湿度
SAMSUNG 45mm F1.8 [T6] 2D/3D
45 mm
69.3 mm
7
6
34.7°
2D- F1.8, 3D- T6
F22
9
0.5 m
0.12X
附带
否
三星 NX 接口
43 mm
62 mm
44.5 mm
122 g
0–40 °C
5–85%
健康与安全信息
警告
注意
•不要通过镜头或相机看太阳。否则可能会严重损伤您
的眼睛。
•使您的镜头或相机远离儿童和宠物。
•不要在未安装镜头盖的情况下,将镜头放在阳光直射
的地方。直射的阳光通过镜头后聚焦在易燃物上可能
导致火灾。
•请仅使用坚固的三脚架。轻型或不稳定的三脚架可能
会倒塌并损坏相机。
•镜头是精密光学设备,小心不要掉落或受到其他物体的撞击。
•避免在温度频繁变化的地方使用镜头,将镜头放在塑料袋或相
机包,防止镜头内外会产生水珠。
•携带或不使用镜头时,请在镜头上装上镜头盖或镜头接口盖,
以免镜头被异物污染或被划伤。
•不要把没带镜头盖的相机放在三脚架上,相机内部零件可能被
直射的阳光损坏。
•为保持镜头性能,每一年或两年检查一次。
•不要对镜头前面施加外力。
•为了安全地使用镜头,请在电源关闭的状态下安装或拆卸镜
头。
•对于使用其他公司镜头造成的任何损坏,三星不承担任何责
任。
•在安装镜头时,确保仅在清洁的环境更换镜头并且不要将手指
伸到镜头接口中。如果有异物进入相机机身或镜头,可能会影
响拍摄效果或导致故障。
产品中有害物质的名称及其含量
有害物质
部件名称 铅
汞
镉 六价铬 多溴联苯 多溴二苯醚
(Pb) (Hg) (Cd) (Cr6+) (PBB)
(PBDE)
镜头/LENS
×
○
○
○
○
○
本表格依据 SJ/T 11364 的规定编制
○: 表示该有害物质在该部件所有均质材料中的含量均在
GB/T 26572 规定的限量要求以下。
×: 表示该有害物质至少在该部件的某一均质材料中的含量
超出 GB/T 26572 规定的限量要求。
□ 产品名: 镜头(Lens)
□ 环保使用期限:10年
- 只有按照本产品使用说明书中的方法正常使用
时,环保使用期限才能有效
镜头的存储和维护
中国制造 天津三星光电子有限公司
•请勿将镜头存放在密闭的空间、靠近化学物品地方或高温或湿
度大的区域。
•镜头没有防水功能,在水附近使用时,小心不要弄湿镜头。
•不要使用任何化学药品如稀释剂、酒精或苯擦镜头的灰尘。
中国 天津津港公路微电子工业区张衡道9号
保留备用
A
English
1
2
6
4
Before Using This Device
Update the firmware of the camera body and lens.
Visit www.samsung.com to download the firmware.
Unpacking
3
5
B
Lens, Lens cap, Lens mount cover, Hood, Leather case,
User manual
•Optional Item: Filter
Layouts (See illustration A)
1 Lens mount index 2 Focus ring 3 Lens
4 i-Function button 5 2D/3D switch
6 Lens information contacts
Attaching and Removing the Lens
C
► To attach the lens,
1 Remove the lens cap, lens mount cover, and body cap.
2 Align the red mark on the lens with the red mark on the
camera body. Then, rotate the lens as shown in the
illustration until it locks into place. (See illustration B)
► To remove the lens, press and hold the lens release
button, and then rotate the lens as shown in the
illustration. (See illustration C)
Using the focus ring
D
E
F
In the MF mode, adjust the focus manually by rotating the
focus ring on the lens. You can select the MF mode on the
camera.
Shooting in 3D mode (See illustration D)
Set the 2D/3D switch on the lens to 3D, and then capture a
photo or video 1.5–5 m away from the subject. You can take
3D photos or videos with the lens.
•3D mode is always on, regardless of the mode dial of the
camera, except B.
•You can use 3D mode only with a camera that supports
the 3D function. In 3D mode, the aperture value is
approximately set to F6.
•Photos captured with the 3D function are saved in JPEG
(2D) and MPO (3D) formats. On your camera’s display,
you can view only JPEG files.
•Shooting in low temperatures may result in color distortion
in images and may consume more battery power.
•You may not be able to shoot properly in conditions below
8.5 LV/900 lux. For best results, capture photos in places
with sufficient light.
•When you photograph objects that contain polarizing
material, such as a display, sunglasses, or a polarizing
filter, or use the polarizing material with your lens, the
images may appear dark or the 3D effect may not be
applied properly.
•Capturing photos or videos with the 3D setting in 2D
mode may result in a less pronounced 3D effect than
those captured in 3D mode. To increase the 3D effect, set
the 2D/3D switch to 3D.
•If you rotate or tilt the camera vertically while shooting, the
3D effect may not be applied properly. Capture images
with the camera in the normal position.
•If you shoot in fluorescent lighting or capture images
displayed by projectors or TVs, the images may appear
black due to the flicker effect.
•Do not view the 3D photos or videos captured by your
camera on a 3D TV or 3D monitor for an extended period
of time. It may cause unpleasant symptoms, such as
eyestrain, fatigue, nausea, and dizziness.
•If you feel dizzy or disoriented while viewing 3D photos or
videos, discontinue use of the 3D feature immediately. If
the problem persists, consult a healthcare professional.
Using i-Function
When you press the i-Function button on the lens, you can
select E to adjust the depth of field or select Z
to zoom in on a subject. This feature is available only when
your camera supports i-Function. Available options may differ
depending on shooting modes.
1 Rotate the mode dial to P, A, S, M, or i.
2 Press [i-Function] on the lens to select a setting.
•Available settings may differ depending on the shooting
mode.
3 Rotate the focus ring on the lens to adjust the setting (or
to change the zoom rate in Z mode).
Using a Lens Hood (See illustration E)
To prevent deterioration of image quality by blocking out
unnecessary light, use a lens hood.
To ensure proper lighting, remove the lens hood or adjust
the distance between the camera and subjects.
Using a Filter (optional) (See illustration F)
Before putting a filter on the lens, make sure it is compatible.
Refer to "Specifications" for compatible filter size.
•When using a filter, keep away from dust, dirt, or
scratches. Also, do not try to mount two or more filters
at the same time. Doing so may deteriorate the image
quality and cause vignetting.
•In case of a thick framed filter, the vignetting can occur
with a wide-angle lens.
Specifications
Lens Name
Focal Length
Focal Length in 35 mm
Equivalent
Lens ConstructionElements
Lens ConstructionGroups
Angle of View
Maximum Aperture
Minimum Aperture
Number of Diaphragm
Blades
Minimum Focus
Distance
Maximum Magnification
Lens Hood
Optical Image Stabilizer
Mount Type
Filter Size
Max. Diameter
Length
Weight (Lens Only,
Approx.)
Operating Temperature
Operating Humidity
SAMSUNG 45mm F1.8 [T6] 2D/3D
45 mm
69.3 mm
7
6
34.7°
2D- F1.8, 3D- T6
F22
9
0.5 m
0.12X
Included
No
Samsung NX Mount
43 mm
62 mm
44.5 mm
122 g
0–40 °C
5–85 %
Health and Safety Information
•Do not stare at the sun through the lens or camera.
This may cause severe damage to your eyes.
Warning •Keep your lens or camera away from small children
and pets.
•Do not store the lens in direct sunlight without the
lens cap. Direct sunlight that passes through the
lens may combust if it comes into contact with
Caution flammable materials.
•Use only sturdy tripods. Lightweight or unstable
tripods may fall over and damage the camera.
•Do not drop the lens or apply excessive shock to it. The lens is
a precise optical product.
•Avoid using the lens anywhere there is a sudden temperature
change. Keep the lens in a plastic bag or a camera case to
prevent condensation from forming on the inside or outside of
the lens.
•When carrying or not using the lens, place the lens cap and
lens mount cover on the lens to prevent contamination from
foreign particles and protect the lens from scratches.
•Do not keep the camera mounted on a tripod without the
lens cap. The inside of the camera can be damaged by direct
sunlight.
•Check the lens once every year or two for best performance.
•Do not apply excessive force to the front of the lens.
•For safe use of the lens, mount or dismount the lens while the
camera is turned off.
•Samsung is not responsible for any damage incurred by using
other manufacturers’ lenses.
•Make sure to change lenses only in a clean environment and
do not put your fingers into the lens mount when mounting the
lens. Foreign particles may affect shooting results or cause a
malfunction if they enter the camera body or the lens.
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in countries with separate collection systems)
This marking on the product, accessories or literature
indicates that the product and its electronic accessories
(e.g. charger, headset, USB cable) should not be disposed of
with other household waste at the end of their working life. To
prevent possible harm to the environment or human health from
uncontrolled waste disposal, please separate these items from
other types of waste and recycle them responsibly to promote
the sustainable reuse of material resources. Household users
should contact either the retailer where they purchased this
product, or their local government office, for details of where
and how they can take these items for environmentally safe
recycling. Business users should contact their supplier and
check the terms and conditions of the purchase contract. This
product and its electronic accessories should not be mixed with
other commercial wastes for disposal.
Lens Storage and Maintenance
•Do not store the lens in closed rooms, near chemicals, or in
areas of high temperature or humidity.
•The lens is not waterproof. Be careful not to allow it to get wet
when using it near water.
•Do not use chemicals such as thinner, alcohol, or benzene to
remove dust.
Please refer to the warranty that came with your
product or visit our website www.samsung.com for
after-sales service or inquiries.
Download PDF

advertising