Samsung | SCC-C4203A | Samsung SCC-C4203A 사용자 매뉴얼

220X POWER ZOOM CAMERA
SCC-C4201(P), C4203(P),
C4301(P), C4303(P)
Owner’s Instructions
Gebrauchsanleitung
Guide d’utilisation
Guía del usuario
Istruzioni per l’uso
220x Pow
LOW er Zoo
m
LIG
HT
DIGIT
AL CO
LOR
CAM
ERA
Part : AB68-00366A
Printed in Korea
✽ Be sure to read the "Safety Precautions" in this manual
to ensure correct use and operation of this product.
E
D
F
Es
I
Safety Precautions
The purpose of safety precautions is to prevent
accidental injury or property damage. Always observe
all safety precautions.
✽ The precautions are divided into "Warnings" and
"Cautions" as distinguished below:
Warning
Ignoring this precaution
may result in death or
serious injury.
Caution
Ignoring this precaution
may result in injury or
damage to property.
Warnings
1. Be sure to use only the standard adapter which is
specified in the specification sheet. (page 28~31)
Using any other adapter could cause fire, electrical
shock, or damage to the product.
2. Check the external connection terminals first before
connecting the power source and signal wires.
Connect the alarm signal wires to the alarm
terminals. Connect the DC12V power adapter to
the SCC-C4201(P)/C4203(P) power input, making
sure that the currect polarity is observed.
Connect the DC12V or AC24V power adapter to
the SCC-C4301(P)/C4303(P) power input.
3. Do not connect multiple cameras to a single
adapter. (Exceeding the capacity may cause
abnormal heat generation or fire.)
1
4. Securely plug the power cord into the power
receptacle. (A loose connection may result in fire.)
5. When mounting the camera on a wall or ceiling,
fasten it safely and securely. (A falling camera may
cause personal injury.)
E
6. Do not place conductive objects (e.g.,
screwdrivers, coins, and metal things) or containers
filled with water on top of the camera. (Serious
injury may result from fire, electrical shock, or
falling objects.)
7. Do not install the unit in humid, dusty, or sooty
locations. (Doing so may cause fire or electrical
shock.)
8. If any unusual smells or smoke come from the unit,
stop using the product. In such case, immediately
disconnect the power source and contact the
service center. (Continued use in such a condition
may cause fire or electrical shock.)
9. If this product fails to operate normally, contact the
store of purchase or your nearest service center.
Never disassemble or modify this product in any
way. (Problems caused by unauthorized user
disassembly or repairs are not covered by your
warranty.)
10. When cleaning, do not spray water directly onto
parts of the product. (Doing so may cause fire or
electrical shock.) Gently wipe the surface with a dry
cloth. Never use detergents or chemical cleaners
on the product, as this may result in discoloration
of surface or cause damage to the finish.
2
Contents
Cautions
1. Do not drop objects on the product or apply strong
shock to it. Keep away from a location subject to
excessive vibration or magnetic interference.
2. Do not install in a location subject to high
temperature, low temperature, or high humidity.
(Doing so may cause fire or electrical shock.)
3. Avoid a location which is exposed to direct sunlight,
or near heat sources such as heaters or radiators.
(Neglecting to do so may result in a risk of fire.)
4. If you want to relocate the already installed product,
be sure to turn off the power before moving or
reinstalling it.
5. Install in a well-ventilated location.
6. Remove the power plug from the outlet when there
is a lightning storm. (Neglecting to do so may cause
fire or damage to the product.)
1. Overview.............................................................5
2. Part Names and Functions ...............................6
3. Installation ........................................................ 8
Checking the Package Contents ....................... 8
Preparing the Cables ........................................ 9
Connecting the Cables .................................... 10
4. Navigating the Setup Menu........................... 12
Structure of the Setup Menu ...........................
- CAMERA ID...................................................
- IRIS................................................................
- BLC................................................................
- ALC ...............................................................
- MANU ............................................................
- SHUTTER......................................................
- AGC (MOTION) .............................................
- WHITE BAL ...................................................
- SPECIAL .......................................................
- AUTO FOCUS ...............................................
- MOTION DET ................................................
- PRESET ........................................................
- COLOR/ BW ..................................................
- EXIT...............................................................
12
16
17
17
17
18
19
20
21
22
24
24
25
26
28
5. Specifications ............................................... 29
3
4
E
1
Overview
2
Part Names and Functions
This camera is a high performance surveillance camera that
provides a maximum of 220x zoom surveillance capability
with its 22x optical zoom lens and digital zoom IC.
It is a multifunction camera that is equipped with all of the
key features of the existing surveillance cameras :
●
E
Day & Night function (SCC-C4203(P), C4303(P)) that
ensures sharp and clear images even at night.
●
Low - Light Surveillance function that enables image
capture even under extremely low light conditions.
●
White Balance function that provides accurate color
rendition under any light conditions.
●
BLC function that enables effective back light
compensation even under a spotlight or a very bright
incident light.
●
Auto Focus function that automatically tracks and focuses
on the moving subject.
●
RS485/ Wired remote control function.
220x Power Zoom
LOW LIGHT
DIGITAL COLOR CAMERA
SET-UP button
REMOTE
RS-485
POWER
Instead of “POWER”, “DC IN”
is writtern in
SCC-C4201(P)/4203(P).
Instead of “POWER”, “PWR
IN” and instead of “GND”,
“DC12&AC24V” is writtern in
SCC-C4301(P)/4303(P).
Broadcast System
●
●
SCC-C4201/ C4203/ C4301/ C4303 : NTSC System
SCC-C4201P/ C4203P/ C4301P/ C4303P : PAL System
Power System/Power Consumption
●
●
SCC-C4201(P), C4203(P) : DC 12V/5.0W
SCC-C4301(P), C4303(P) : AC 24V, DC 12V/5.5W
SET-UP button
The function of the SET-UP button varies depending on
whether you are currently in Normal Operation mode (i.e.,
the Setup Menu is not displayed) or Setup Menu mode.
☞ In Normal Operation Mode
- UP/ DOWN buttons : Use as the ZOOM Tele button
and the ZOOM Wide button respectively.
- LEFT/ RIGHT buttons : Use as the FOCUS Near
button and the FOCUS Far button respectively.
- SET- UP button: Use to enter the Setup Menu.
Hold the SET- UP button for longer than 3 seconds to
enter the Setup Menu.
5
6
3
☞ In Setup Menu Mode
Installation
- UP/ DOWN buttons: Use to move the cursor up or down.
- LEFT/ RIGHT buttons: Use to move the cursor left or
right, or to sequentially view the values that can be
assigned to a parameter.
- ENTER button: Use to select a Sub Menu item, and to
accept the current value.
ZOOM/ FOCUS REMOTE terminals
Use to control ZOOM/ FOCUS from an external controller.
Depending on the input conditions, the terminals can be
set to 4 different modes.
(Operating Voltage Range : +3V ~+13V, -3V~-13V)
Item
Code
A
B
C
D
Tele
-6V
-6V
+6V
+6V
Wide
+6V
+6V
-6V
-6V
Far
+6V
-6V
+6V
-6V
Near
-6V
+6V
-6V
+6V
Caution : In the event of a simultaneous input of RS485 and
wired remote control signal, whichever was input first
will be activated.
Before Installation
Checking the Package Contents
Make sure that the following accessories are included in
the package.
220x Powe
LOW
E
r Zoom
LIG
DIGITA
HT
L CO
LOR
CAM
ERA
SCC-C4201(P),C4203(P),
C4301(P),C4303(P)
User's Guide
ALARM OUT terminal
An alarm signal is output from this terminal when the
MOTION DET mode is activated or BW mode is activated.
(Open Collector: DC24V 40mA Max)
VIDEO OUT terminal
Connect the monitor's VIDEO IN. The video signal from
the camera is transmitted to the monitor via this terminal.
RS485 terminal
RS485 remote control terminal.
Mount Adapter
Screw (2)
Terminal Block
Power LED
Lights when power is on.
POWER IN terminal
Plug in the power adapter here.
7
8
Preparing the Cables
To install and use the camera, first prepare the following
cables.
The requirements for the power adapter, which connects to
the camera's POWER IN terminal, are as follows:
●
●
Connecting the Cables
1. Connect one end of the BNC cable to the VIDEO OUT.
2. Connect the other end of the BNC cable to the VIDEO IN
of the monitor.
SCC-C4201(P), SCC-C4203(P) : DC12V 600mA
SCC-C4301(P), SCC-C4303(P) : AC24V 300mA
DC12V 600mA
E
Video terminals on the back
of the monitor
BNC cable
REMOTE
RS-485
POWER
3. Plug in the power adapter. Use a "minus" screwdriver to
connect one part of the power adapter, which consists of
two lines, to the POWER terminal of the camera as follows :
Video Cable
Use a BNC cable, such as the one shown below, to connect
the camera's VIDEO OUT to the monitor.
POWER SELECTION switch
underneath the power adapte
POWER SELECTION
switch underneath the
power adapte
9
REMOTE
RS-485
POWER
10
4
4. Determine the type of power supply and set the POWER
SELECTION switch accordingly. Next, plug the power
adapter into a wall outlet.
The requirements for the power adapter for each model are
as follows:
●
●
SCC-C4201(P), SCC-C4203(P) : DC12V 600mA
SCC-C4301(P), SCC-C4303(P) : AC24V 300mA
DC12V 600mA
5. If the camera operates normally, the following screen will
be displayed for 5 seconds and then disappears.
SAMSUNG PROTOCOL
ADDR : 0
TYPE : RS-485, HALF
BAUD : 9600
LENS CHECK : OK!
Navigating the Setup Menu
In this chapter, we will take a look at the menu system of the
SCC-C4201(P), C4203(P), C4301(P), and C4303(P). First,
we will take a look at the structure of the Setup Menu and
then describe the functions of each menu item in the menu.
Structure of the Setup Menu
●
E
Structure of the Setup Menu of the SCC-C4201(P)
CAMERA ID
OFF/ON...
IRIS
ALC.../MANU...
SHUTTER
OFF/1/100(1/120) ~ 1/10K
/AUTO X2~X128/FIX X2~X128
AGC
OFF/LOW/HIGH
MOTION
S.S/SLOW/NORMAL/FAST/F.F
WHITE BAL
ATW/AWC/MANU...
SPECIAL
...
6. The requirements for RS485 control is as follows :
● Signaling Speed: 9600 bps
● Data Bit : 8 bits
● Stop Bit : 1 bit
● Parity Bit : none
LANGUAGE
ENGLISH
CTRL TYPE
A/B/C/D
RS-485
...
PIP
OFF/ON...
MIRROR
OFF/ON
D-ZOOM
OFF/X2 ~ X10
POSI/NEGA
+/-
ZOOM SPEED
1/2/3/4
DETAIL(0)
---- I----
RET
11
AUTO FOCUS
AF/MF/ONEAF
MOTION DET
OFF/ON...
PRESET
...
EXIT
QUIT/SAVE/PRESET
12
Structure of the Setup Menu
●
Structure of the Setup Menu of the SCC-C4203(P)
●
Structure of the Setup Menu of the SCC-C4301(P)
CAMERA ID
OFF/ON...
CAMERA ID
OFF/ON...
IRIS
ALC.../MANU...
IRIS
ALC.../MANU...
SHUTTER
OFF/1/100(1/120) ~ 1/10K
/AUTO X2~X128/FIX X2~X128
SHUTTER
OFF/1/100(1/120) ~ 1/10K
/AUTO X2~X128/FIX X2~X128
AGC
OFF/LOW/HIGH
AGC
OFF/LOW/HIGH
MOTION
S.S/SLOW/NORMAL/FAST/F.F
MOTION
S.S/SLOW/NORMAL/FAST/F.F
WHITE BAL
ATW/AWC/MANU...
WHITE BAL
ATW/AWC/MANU...
SPECIAL
...
SPECIAL
...
LANGUAGE
ENGLISH
LANGUAGE
CTRL TYPE
A/B/C/D
V-SYNC
INT/LINE...
RS-485
...
CTRL TYPE
A/B/C/D
ENGLISH
PIP
OFF/ON...
RS-485
MIRROR
OFF/ON
PIP
OFF/ON...
D-ZOOM
OFF/X2 ~ X10
MIRROR
OFF/ON
POSI/NEGA
+/-
D-ZOOM
OFF/X2 ~ X10
ZOOM SPEED
1/2/3/4
POSI/NEGA
+/-
DETAIL(0)
---- I----
ZOOM SPEED
1/2/3/4
DETAIL(0)
----I----
RET
E
...
RET
13
AUTO FOCUS
AF/MF/ONEAF
MOTION DET
OFF/ON...
AUTO FOCUS
AF/MF/ONEAF
PRESET
...
MOTION DET
OFF/ON...
COLOR/BW
COLOR/BW/AUTO...
PRESET
...
EXIT
QUIT/SAVE/PRESET
EXIT
QUIT/SAVE/PRESET
14
Structure of the Setup Menu
●
Structure of the Setup Menu of the SCC-C4303(P)
CAMERA ID
OFF/ON...
IRIS
ALC.../MANU...
SHUTTER
OFF/1/100(1/120) ~ 1/10K
/AUTO X2~X128/FIX X2~X128
EXIT
AGC
OFF/LOW/HIGH
MOTION
S.S/SLOW/NORMAL/FAST/F.F
WHITE BAL
ATW/AWC/MANU...
SPECIAL
...
LANGUAGE
[SCC-C4201(P),SCC-C4301(P)]
E
[SCC-C4203(P),SCC-C4303(P)]
ENGLISH
INT/LINE...
CTRL TYPE
A/B/C/D
PIP
QUIT
The COLOR/BW option is available only with the
SCC-C4203(P) and C4303(P).
V-SYNC
RS-485
(SET UP)
CAMERA ID
OFF
IRIS
ALC...
SHUTTER
OFF
AGC
LOW
WHITE BAL
ATW
SPECIAL
...
AUTO FOCUS
ONEAF
MOTION DET
OFF
PRESET
...
COLOR/BW
COLOR
EXIT
QUIT
(SET UP)
CAMERA ID
OFF
IRIS
ALC...
SHUTTER
OFF
AGC
LOW
WHITE BAL
ATW
SPECIAL
...
AUTO FOCUS
ONEAF
MOTION DET
OFF
PRESET
...
...
OFF/ON...
MIRROR
OFF/ON
D-ZOOM
OFF/X2 ~ X10
POSI/NEGA
+/-
ZOOM SPEED
1/2/3/4
DETAIL(0)
----I----
CAMERA ID
In the CAMERA ID menu, you can assign an ID to the camera
that appears on the monitor screen. If you select ON...
for CAMERA ID and press the ENTER button, a screen from
which you can assign a camera ID will appear.
You can use alphanumeric characters and a few special
characters that are displayed on the screen to assign a
maximum of 20 characters for the CAMERA ID.
You can use the LOCATION option to place the camera ID
anywhere on the screen.
RET
15
AUTO FOCUS
AF/MF/ONEAF
MOTION DET
OFF/ON...
PRESET
...
COLOR/BW
COLOR/BW/AUTO...
EXIT
QUIT/SAVE/PRESET
(SET UP)
CAMERA ID
ON...
IRIS
ALC...
SHUTTER
OFF
AGC
LOW
WHITE BAL
ATW
SPECIAL
...
AUTO FOCUS
ONEAF
MOTION DET
OFF
PRESET
...
COLOR/BW
COLOR
EXIT
QUIT
(CAMERA ID)
A B C D
MNO P
Y Z 0 1
: ! -
Press the
ENTER
button.
E
Q
2
+
F
R
3
*
G
S
4
(
H
T
5
)
I J K L
U VWX
6 7 8 9
/
SP
SP
LOCATION...
RET
ZOOM.CAMERA.........
16
IRIS
The level of video output to the monitor can be controlled by
the iris lens according to the intensity of the incoming light.
This product is equipped with an iris lens. In the ALC (Auto
Light Compensation) menu, you can set the video output
level. In the MANU menu, you can manually set the opening
and closing of the iris.
BLC (Option in the ALC Menu)
SIZE
➞
If you select ALC for IRIS and press the ENTER button, a
screen from which you can set the video output level and BLC
will appear. In the LEVEL option, you can use the LEFT/
RIGHT buttons to set the video output level. If you set the
BLC to ON, the BLC function will be applied to the screen
area specified in the AREA option. The AREA option can be
set to either PRESET or USER to specify the screen area to
which the BLC function will be applied. If you set the AREA
option to PRESET, the BLC function will be applied to the
area specified at the time of factory shipment.
17
➞
➞
ALC
(SET UP)
CAMERA ID
OFF
IRIS
ALC...
SHUTTER
OFF
AGC
LOW
WHITE BAL
ATW
SPECIAL
...
AUTO FOCUS
ONEAF
MOTION DET
OFF
PRESET
...
COLOR/BW
COLOR
EXIT
QUIT
SIZE
➞
If you use an ordinary camera when a strong light source,
such as a spot light, is shining from behind the subject, the
subject will appear dark on the monitor because of the back
light. For the SCC-C4201(P), C4203(P), C4301(P), and
C4303(P), appropriately set the BLC in the ALC menu to
solve the back -light problem and have a clear picture even
under a spotlight or a very bright incident light.
If you set the AREA option to USER and press the ENTER
button, you can customize the area to which the BLC function
will be applied. You can specify the size of the area by using
the UP, DOWN, LEFT, and RIGHT buttons. After setting the
size of the area, press the ENTER button. The specified area
will start flashing. Then, you can use the UP, DOWN, LEFT
and RIGHT buttons to specify the location of the area.
Use the ENTER button and the UP, DOWN, LEFT and
RIGHT buttons to specify the size of the area and to position E
the area. Press the ENTER button again to exit the AREA
setting menu.
(ALC)
Press the
ENTER
button.
AREA
BLC
LEVEL
RET
PRESET...
OFF
( 0) ----I----
POSITION
Use the UP,
DOWN,
LEFT, and
RIGHT
buttons.
POSITION
MANU
If you select MANU for IRIS and press the ENTER button, a
screen from which you can manually adjust the iris to a
desired level will appear. In the LEVEL option, you can use
the LEFT/ RIGHT buttons to set the manual opening and
closing of the iris.
(SET UP)
CAMERA ID
OFF
IRIS
MANU...
SHUTTER
OFF
AGC
LOW
WHITE BAL
ATW
SPECIAL
...
AUTO FOCUS
ONEAF
MOTION DET
OFF
PRESET
...
COLOR/BW
COLOR
EXIT
QUIT
(MANUAL)
Press the
ENTER
button.
LEVEL ( 00) ----I---RET
18
SHUTTER
AGC (MOTION)
In the SHUTTER option, you can specify the speeds of the
high-speed electronic shutter, auto low-speed shutter, and fix
low-speed shutter. The high - speed electronic shutter
supports 7 shutter speeds from 1/100 seconds to 1/10K
seconds, and the auto low-speed shutter and fix low-speed
shutter support 12 shutter speeds from 2x to 128x
respectively. The low-speed shutter allows you to set the
shutter speed to a slow setting to obtain a clearer video
when shooting in dark lighting conditions. Select an auto low
-speed shutter in order to have the camera detect the
amount of light and automatically set the shutter speed to a
slow setting according to the degree of darkness. Select an
item that starts with "FIX" to specify the shutter speed
yourself. The numbers that immediately follow the "AUTO"
and "FIX" indicate the number of accumulated fields.
The higher the field number, the slower the shutter speed.
Accordingly, a still picture will be sharper. In the case of
video, an image captured of an object will be blurry.
In the AGC (Automatic Gain Control) option, you can specify
whether to automatically control the GAIN when the obtained
video is below a certain level of brightness because it was
recorded under insufficient lighting. To automatically control
the GAIN, set the AGC option to LOW or HIGH. Otherwise,
set it to OFF. If the you set the AGC option to LOW, the
maximum GAIN of the AGC will be set to low, and if set to
HIGH, the maximum GAIN will be set to high.
If the SHUTTER option is set to an auto low-speed, the AGC
option will change to the MOTION option. In the MOTION
option, use the LEFT and RIGHT buttons to select from S.S, E
SLOW, NORMAL, FAST, and F.F.
(SET UP)
CAMERA ID
OFF
IRIS
ALC...
SHUTTER
OFF
AGC
LOW
WHITE BAL
ATW
SPECIAL
...
AUTO FOCUS
ONEAF
MOTION DET
OFF
PRESET
...
COLOR/BW
COLOR
EXIT
QUIT
SHUTTER
➞ OFF ➞ 1/100(1/120) ➞ 1/250 ➞ 1/500 ➞ 1/1000 ➞ 1/2000 ➞
1/4000 ➞ 1/10K ➞ OFF ➞ AUTOX2 ➞ AUTOX4 ➞ AUTOX6 ➞
AUTOX8 ➞ AUTOX12 ➞ AUTOX16 ➞ AUTOX24 ➞ AUTOX32
➞ AUTOX48 ➞ AUTOX64 ➞ AUTOX96 ➞ AUTOX128 ➞ OFF
➞ FIXX2 ➞ FIXX4 ➞ FIXX6 ➞ FIXX8 ➞ FIXX12 ➞ FIXX16 ➞
FIXX24 ➞ FIXX32 ➞ FIXX48 ➞ FIXX64 ➞ FIXX96 ➞ FIXX128
19
(SET UP)
CAMERA ID
OFF
IRIS
ALC...
SHUTTER
AUTOX4
MOTION
NORMAL
WHITE BAL
ATW
SPECIAL
...
AUTO FOCUS
ONEAF
MOTION DET
OFF
PRESET
...
COLOR/BW
COLOR
EXIT
QUIT
☞
☞
☞
☞
☞
S.S : Select to maximally enhance the resolution of a still
image by increasing the lowest value of AGC GAIN and
the scale of low speed shutter to their maximum.
(This is used mainly to monitor almost still objects in dark
places.)
SLOW : Select to enhance the resolution of a still image
as much as possible by increasing a low value of AGC
GAIN and the scale of low speed shutter. (This is used
mainly to monitor objects that make a small movement in
dark places.)
NORMAL : Select to display the normal picture with a
medium value of AGC GAIN and the scale of normal
speed shutter. (This is used mainly to monitor moving
objects in dark places.)
FAST : Select to focus on the moving objects by
decreasing a high value of AGC GAIN and the scale of
normal speed shutter. (This is used mainly to monitor
objects showing active movements in dark places.)
F.F : Select to focus on the moving objects by
decreasing the highest value of AGC GAIN and the scale
of low speed shutter to their minimum. (This is used
mainly to monitor fast moving objects in dark places.)
20
WHITE BAL
SPECIAL
In the WHITE BAL option, you can set the White Balance
function, which enables you to see the white color correctly
under illumination of any color temperature. If you set the
WHITE BAL option to ATW, the camera will continuously
monitor changes in the ambient color temperature and
automatically set the White Balance according to the color
temperature. If you set the WHITE BAL option to AWC, place
a piece of white paper in front of the camera, and press the
ENTER button, the Auto White Balance Control will be
activated just once to set the color temperature and this
value will be maintained.
You can manually adjust the LANGUAGE, V-SYNC, CTRL TYPE,
RS485, PIP, MIRROR, D-ZOOM, POSI/ NEGA, ZOOM SPEED,
and DETAIL.
If you set the WHITE BAL option to MANUAL, you can
customize the white balance to take into account the current
lighting condition.
☞
☞
☞
3200°K : Select to set the color temperature to 3200°K.
5600°K : Select to set the color temperature to 5600°K.
USER : Select to set the color temperature by selecting
appropriate values from the RED and BLUE
graphs.
MANU : If you select the MANU option and press the
ENTER button, a screen from which you can manually select
the white balance will appear. In the PRESET option, use the
LEFT and RIGHT buttons to select 3200°K, 5600°K, or
USER.
(SET UP)
CAMERA ID
OFF
IRIS
ALC...
SHUTTER
OFF
AGC
LOW
WHITE BAL
MANU...
SPECIAL
...
AUTO FOCUS
ONEAF
MOTION DET
OFF
PRESET
...
COLOR/BW
COLOR
EXIT
QUIT
(AWB/MANU)
Press the
ENTER
button.
PRESET OFF(USER)..
RED
(-2C) - - - I - - - BLUE
(-5B) - I - - - - - RET
The V-SYNC option is available only with the SCC-C4301(P)
and C4303(P).
If you press the ENTER button while in "---" is shown, the
SPECIAL screen from which you can set the special functions
will appear. When activating each function, use the LEFT and
RIGHT buttons to set the desired item.
(SET UP)
CAMERA ID
OFF
IRIS
ALC...
SHUTTER
OFF
AGC
LOW
WHITE BAL
ATW
SPECIAL
...
AUTO FOCUS
ONEAF
MOTION DET
OFF
PRESET
...
COLOR/BW
COLOR
EXIT
QUIT
Press the
ENTER
button.
E
(SPECIAL)
LANGUAGE
ENGLISH
V-SYNC
INT
CTRL TYPE
A
RS-485
...
PIP
OFF
MIRROR
OFF
D-ZOOM
OFF
POSI/NEGA
+
ZOOM SPEED
3
DETAIL
(0) ----I-RET
: Specify the vertical synchronization method that
☞ Vwill- SYNC
be used by the SCC-C4301(P) and C4303(P).
There are 2 types of vertical synchronization signal that the
camera supports : INT mode in which the signal is generated
by the camera's internal clock and LINE mode which sets the
vertical synchronization by the external power frequency. If
you select LINE and press ENTER button, the LL-PHASE
screen from which you can adjust the phase of LINE LOCK
will appear. You can specify the desired phase level in the
PHASE option.
(SPECIAL)
LANGUAGE
ENGLISH
V-SYNC
LINE...
CTRL TYPE
A
RS-485
...
PIP
OFF
MIRROR
OFF
D-ZOOM
OFF
POSI/NEGA
+
ZOOM SPEED
3
DETAIL
(0) ----I-RET
(LL-PHASE)
Press the
ENTER
button.
PHASE (0)
RET
----|----
If you are using DC power supply, it will work only in INT mode.
For LINE mode operation, use the AC power adapter (50Hz).
21
22
☞
☞
CTRL TYPE : You can select the A, B, C, or D mode
depending on the input of the wired remote control terminal.
(See page 7.)
RS-485 : It sets up ADDRESS, PROTOCOL, and BAUD
RATE of RS-485 communication.
(BAUD RATE: 2400bps, 4800bps, 9600bps, 19200bps, 38400bps)
Caution : A communication error may occur if you connect
more than one camera set with an identical address.
☞
PIP : This is the Picture in Picture feature. It will show a
screen reduced by 1/16 of the main screen only when
operating the Digital Zoom. If you set the PIP option to ON
and press the ENTER button, you can use the UP, DOWN,
LEFT, and RIGHT buttons to set the PIP position.
* The PIP feature does not work in a low speed shutter mode.
The MIRROR feature does not work on the PIP window.
(SPECIAL)
EANGUAGE
ENGLISH
V-SYNC
LINE...
CTRL TYPE
A
RS-485
...
PIP
ON
MIRROR
OFF
D-ZOOM
OFF
POSI/NEGA
+
ZOOM SPEED
3
DETAIL
(0) ----I-RET
☞
☞
☞
☞
23
In the AUTO FOCUS option, you can specify the Focus
method to AF, MF, or ONEAF.
☞
☞
☞
AF : Focuses automatically by continuously monitoring the
screen in AUTO FOCUS mode. It does not process the
FOCUS button input because it focuses automatically
during ZOOM.
MF : You can manually adjust
(SET UP)
CAMERA ID
OFF
E
the focus.
IRIS
ALC...
SHUTTER
OFF
ONEAF : Focuses about 5
AGC
LOW
seconds only when ZOOM is
WHITE BAL
ATW
SPECIAL
...
moved Wide to Tele. It is same
AUTO FOCUS
AF
as MF mode while in STOP
MOTION DET
OFF
PRESET
...
mode, and same as AF mode
COLOR/BW
COLOR
after ZOOM Tele.
EXIT
QUIT
MOTION DET
Press the
ENTER
button.
PIP
MIRROR : Horizontally flips the video output signal.
D-ZOOM : Sets the magnification of the Digital Zoom.
The magnification level can be set to up to 10x.
POSI/ NEGA : Outputs the video output signal normally or
inversely.
ZOOM SPEED : In the ZOOM SPEED option, use the
LEFT and RIGHT buttons to set the speed as follows:
1 : Takes about 17 seconds from 1 x to 22 x magnification (slowest speed).
2 : Takes about 10 seconds from 1 x to 22 x magnification (slow speed).
3 : Takes about 6 seconds from 1 x to 22 x magnification (fast speed).
4 : Takes about 3 seconds from 1 x to 22 x magnification (fastest speed).
☞
AUTO FOCUS
In the MOTION DET option, you can set the Motion
Detection function, motion detection sensitivity, and the
motion detection area. If you set the Motion Detection
function, you can detect an intruder's movement and check it
through the monitor and the ALARM OUT terminal.
If you set ALARM which is located under COLOR/BW
AUTO menu to ON while MOTION DET remains ON, the
ALARM output port can not send any motion.
(SET UP)
CAMERA ID
OFF
IRIS
ALC...
SHUTTER
OFF
AGC
LOW
WHITE BAL
ATW
SPECIAL
...
AUTO FOCUS
ONEAF
MOTION DET
ON...
PRESET
...
COLOR/BW
COLOR
EXIT
QUIT
(MOTION DET)
Press the
ENTER
button.
AREA
SENSITIVITY
RET
PRESET...
MEDIUM
DETAIL: Adjusts the sharpness.
24
If you select ON and press the ENTER button, the MOTION
DET screen will come up. You can set the AREA to which the
Motion Detection function will be applied to either PRESET or
USER. If you set the AREA option to PRESET, the Motion
Detection function will be applied to the areas preset as factory
defaults. If you set the AREA option to USER and press the
ENTER button, you can change the area size and position and
select the area where you want to apply the Motion Detection
function. You can specify the size of the area by using the UP,
DOWN, LEFT, and RIGHT buttons. If the area is not flashing,
press the ENTER button. When the area starts flashing, use the
UP, DOWN, LEFT and RIGHT buttons to specify the location of
the area. Use the ENTER button and the UP, DOWN, LEFT,
and RIGHT buttons to specify the size of the area and to
position the area. Press the ENTER button again to exit the
AREA setting menu. You can use the SENSITIVITY option to
set the motion detection sensitivity. The higher the setting, the
more sensitive the motion detection.
SIZE
SIZE
➞
➞
➞
➞
POSITION
Use the UP,
DOWN,
LEFT, and
RIGHT
buttons.
1
6
11
16
21
26
31
2
7
12
17
22
27
3
8
13
18
23
28
4
9
14
19
24
29
RET
ID : PRESET 0
You can store up to 128 ZOOM and FOCUS positions with the
PRESET. You can use the PRESET function when you connect
the SSC-1000 to the RS-485.
25
2
7
12
17
22
27
3
8
13
18
23
28
4
9
14
19
24
29
RET
ID : PRESET 0
POSITION SET
PRESET ID
...
ON...
EXIT
QUIT
Press the
ENTER
button.
If you select a preset number and press the ENTER button, a screen
that looks as above will appear.
☞
☞
POSITION SET : Select to store the ZOOM and FOCUS
positions.
PRESET ID : Select to set an ID for the PRESET position,
as you did with Camera ID.
COLOR / BW
☞
☞
(PRESET MAP)
Press the
ENTER
button.
1
6
11
16
21
26
31
In the COLOR / BW option, you can set the IR (infrared) Filter to ON or
OFF. In the BW mode, the IR Filter is turned OFF and the level of
sensitivity is increased to a level comparable to a black and white
camera. In the COLOR mode, on the other hand, the IR Filter is turned
ON and the screen turns normal, as the level of sensitivity is decreased.
POSITION
0*
5
10
15
20
25
30
0*
5
10
15
20
25
30
PRESET NO. 0
The COLOR / BW option is available only with the SCC-C4203(P)
and C4303(P).
PRESET
(SET UP)
CAMERA ID
OFF
IRIS
ALC...
SHUTTER
OFF
AGC
LOW
WHITE BAL
ATW
SPECIAL
...
AUTO FOCUS
ONEAF
MOTION DET
OFF
PRESET
...
COLOR/BW
COLOR
EXIT
QUIT
(PRESET MAP)
☞
COLOR : The IR Filter is ON and the screen is normal.
BW : The IR Filter is OFF and the screen is black and
white. (Sensitivity to low light is increased to a level
comparable to a black and white camera.)
AUTO : Select to automatically switch between the COLOR
mode and BW mode depending on the amount of light.
In low light conditions, the IR Filter is turned OFF and the
sensitivity to low light is increased by switching to the BW
mode, but in bright light conditions, the IR Filter is turned
ON and the sensitivity is decreased by switching to the
COLOR mode. If you select AUTO and press the ENTER
button, a screen from which you can set the ALARM
ON/OFF, BURST ON / OFF, BW LEVEL and DWELL TIME
will appear.
26
E
- ALARM ON : It sends out signals through the ALARM output
port in the BW mode.
- ALARM OFF : The ALARM output port is synchronized with
the MOTION DET finction regardiess of the COLOR/BW
mode.
- BURST ON : The color burst signal is output together with
black and white composite video signal.
BURST OFF : The color burst signal is not output.
- LEVEL : You can set the brightness level that changes from
COLOR mode to BW mode in 3 steps : LOW, MEDIUM, and
HIGH.
- DWELL TIME : Set the HOLDING time for switching between
COLOR and BW mode depending the changes in the amount
of light. You can set the HOLDING time to 10sec (S), 30sec,
60sec, or 300sec( L).
EXIT
The EXIT option is used to quit the Setup Menu mode and
return to the Normal Operation mode.
☞
☞
☞
QUIT : Select to ignore any changes you have made and
restore the previously saved settings.
SAVE : Select to save the settings that have been
changed so far.
PRESET : Select to ignore any changes you have made
and restore the factory default settings.
In AUTO mode, AGC will operates in high speed mode, and
you cannot change it manually, as it is indicated by "---".
(SET UP)
CAMERA ID
OFF
IRIS
ALC...
SHUTTER
OFF
AGC
--WHITE BAL
ATW
SPECIAL
...
AUTO FOCUS
ONEAF
MOTION DET
OFF
PRESET
...
COLOR/BW
AUTO...
EXIT
QUIT
(BW SETUP)
Press the
ENTER
button.
ALARM
BURST
LEVEL
DWELL TIME
RET
OFF
ON
MEDIUM
S--|----L
Caution : If you use an infrared light source while in AUTO
mode, AUTO switching malfunction and camera
AF malfunction may occur.
27
28
E
5
Specifications
SCC-C4201/C4203
SCC-C4201P/C4203P
Item
Product Type
Power Supply Voltage
Power Consumption
Broadcast System
Description
- 22x Zoom Camera
- DC 12V ± 10%
- 5.0 W
- NTSC Standard Color System
Imaging Device
- 1/4 inch IT CCD
Effective Pixe
- 768(H) x 494 (V)
Scanning Method
Line Frequency
Synchronization Method
- 525 Line, 2:1 Interlace
- Horizontal : 15,734 Hz (INT)
- Vertical : 59.94 Hz (INT)
- INT Only
Remark
Item
Product Type
Power Supply Voltage
Power Consumption
Broadcast System
Imaging Device
Effective Pixe
Scanning Method
Line Frequency
Synchronization Method
- 5.0 W
- PAL Standard Color System
- 752 (H) X 582 (V)
- 625 Line, 2:1 Interlace
- Horizontal : 15,625 Hz(INT)
- Vertical : 50 Hz(INT)
- INT Only
Resolution
- 480 TV Lines
S/N Ratio
- 50dB or more (AGC Off)
S/N Ratio
- 50dB or more (AGC Off)
Minimum Scene Illumination
- 1 Lux (AGC Max, Sense Up 2x)
- 0.02 Lux (Sense Up 128x)
- 0.005 Lux (B/W Mode, Sense Up 128x,
SCC-C4203P Only)
White Balance
- ATW/ AWC/ Manual Mode
(3200°K, 5600°K, R/B Gain Control)
White Balance
- ATW/ AWC/ Manual Mode
(3200°K, 5600°K, R/B Gain Control)
Signal Output
- Composite Video Out : 1.0 Vp-p
75ohms/BNC
Signal Output
- Composite Video Out : 1.0 Vp-p
75ohms/BNC
Lens
- 22x Zoom Lens in a single unit
- Focal length : 3.6 to 79.2 mm
- Aperture : F1.6(Wide), F3.8(Tele)
- IR Filter On/Off (SCC-C4203 Only)
Lens
- 22x Zoom Lens in a single unit
- Focal length : 3.6 to 79.2 mm
- Aperture : F1.6(Wide), F3.8(Tele)
- IR Filter On/Off (SCC-C4203P Only)
Electronic Shutter
- Off, 1/100, 1/250, 1/500, 1/1K, 1/2K,
1/4K, /10K sec
Electronic Shutter
- Off, 1/120, 1/250, 1/500, 1/1K, 1/2K,
1/4K, /10K sec
Back Light Compensation
Sense Up
Digital Zoom
Motion Detection
- Off / On (Area Setting)
- Off/Auto 2x~128x/Fix 2x~128x
- Off / On (x10), PIP
- Off / On (Area / Sensitivity Setting)
Back Light Compensation
Sense Up
Digital Zoom
Motion Detection
Operating Temperature
and Humidity
- 14°F ~ +122°F, ~90 %
Operating Temperature
and Humidity
Dimensions
- 59.5 x 60.5 x 109.5mm
Dimensions
Weight
- 375g
Weight
E
- 1/4 inch IT CCD
- 480 TV Lines
- 1 Lux (AGC Max, Sense Up 2x)
- 0.02 Lux (Sense Up 128x)
- 0.005 Lux (B/W Mode, Sense Up 128x,
SCC-C4203 Only)
Remark
- DC 12V ± 10%
Resolution
Minimum Scene Illumination
29
Description
- 22x Zoom Camera
- Off / On (Area Setting)
- Off/Auto 2x~128x/Fix 2x~128x
- Off / On (x10), PIP
- Off / On (Area / Sensitivity Setting)
- 14°F ~122°F, ~90 %
- 59.5 x 60.5 x 109.5mm
- 375g
30
Specifications
SCC-C4301/C4303
SCC-C4301P/C4303P
Item
Product Type
Power Supply Voltage
Power Consumption
Broadcast System
Description
- 22x Zoom Camera
- AC 24V (60Hz) or DC 12V ± 10%
- 5.5W
- NTSC Standard Color System
Imaging Device
- 1/4 inch IT CCD
Effective Pixe
- 768(H) X 494(V)
Scanning Method
Line Frequency
Synchronization Method
- 525 Line, 2:1 Interlace
- Horizontal : 15,734 Hz(INT), 15,750 Hz(L/L)
- Vertical : 59.94 Hz(INT), 60 Hz(L/L)
- INT / Line Lock
Remark
Item
Product Type
Power Supply Voltage
Power Consumption
Broadcast System
- 5.5W
- 1/4 inch IT CCD
Effective Pixe
- 752(H) X 582(V)
Line Frequency
Synchronization Method
- 625 Line, 2:1 Interlace
- Horizontal : 15,625 Hz(INT), 15,625 Hz(L/L)
- Vertical : 50 Hz(INT), 50 Hz(L/L)
- INT / Line Lock
- 480 TV Lines
Resolution
- 480 TV Lines
S/N Ratio
- 50dB or more (AGC Off)
S/N Ratio
- 50dB or more (AGC Off)
- 1 Lux (AGC Max, Sense Up 2x)
- 0.02 Lux (Sense Up 128x)
- 0.005 Lux (B/W Mode, Sense Up 128x,
SCC-C4303 Only)
Minimum Scene Illumination
- 1 Lux (AGC Max, Sense Up 2x)
- 0.02 Lux (Sense Up 128x)
- 0.005 Lux (B/W Mode, Sense Up 128x,
SCC-C4303P Only)
White Balance
- ATW/ AWC/ Manual Mode
(3200°K, 5600°K, R/B Gain Control)
White Balance
- ATW/ AWC/ Manual Mode
(3200°K, 5600°K, R/B Gain Control)
Signal Output
- Composite Video Out : 1.0 Vp-p
75ohms/BNC
Signal Output
- Composite Video Out : 1.0 Vp-p
75ohms/BNC
Lens
- 22x Zoom Lens in a single unit
- Focal length : 3.6 to 79.2 mm
- Aperture : F1.6(Wide), F3.8(Tele)
- IR Filter On / Off (SCC-C4303 Only)
Lens
- 22x Zoom Lens in a single unit
- Focal length : 3.6 to 79.2 mm
- Aperture : F1.6(Wide),F3.8(Tele)
- IR Filter On/ Off (SCC-C4303P Only)
Electronic Shutter
- Off, 1/100, 1/250, 1/500, 1/1K, 1/2K,
1/4K, /10K sec
Electronic Shutter
- Off, 1/120, 1/250, 1/500, 1/1K, 1/2K,
1/4K, /10K sec
Back Light Compensation
Sense Up
Digital Zoom
Motion Detection
- Off / On (Area Setting)
- Off/Auto 2x~128x/Fix 2x~128x
- Off / On (x10), PIP
- Off / On (Area / Sensitivity Setting)
Back Light Compensation
Sense Up
Digital Zoom
Motion Detection
Operating Temperature
and Humidity
- 14°F ~122°F, ~90 %
Operating Temperature
and Humidity
Dimensions
- 59.5 x 60.5 x 143mm
Dimensions
Weight
- 500g
Weight
E
- PAL Standard Color System
Imaging Device
Scanning Method
Remark
- AC 24V (50Hz) or DC 12V ± 10%
Resolution
Minimum Scene Illumination
31
Description
- 22x Zoom Camera
- Off / On (Area Setting)
- Off/Auto 2x~128x/Fix 2x~128x
- Off / On (x10), PIP
- Off / On (Area / Sensitivity Setting)
- 14°F ~122°F, ~90 %
- 59.5 x 60.5 x 143mm
- 500g
32
Memo
Memo
Download PDF