Samsung | L18200MB | Samsung L18200MB 사용자 매뉴얼

简体中文
镜头
3旋转镜头上的对焦环来调整设置(或在 Z 模式中更
使用本产品前
使用说明书
感谢您购买三星镜头。更新相机机身和镜头的固件。请访问
www.samsung.com 以下载固件。
SAMSUNG 18-200mm F3.5-6.3 ED OIS
拆开包装
此说明书专门为指导您了解镜头基本功能和特征而设计。
为保证安全、正确地使用,请仔细阅读此说明书。
镜头、镜头盖、镜头接口盖、遮光罩、镜头包、使用说明书
•另购项目:滤光镜
各部位名称(见图 A)
AD68-08136A (1.5)
A
B
C
D
0
1
2
3
4
5
9
8
7
6
E
F
1 镜头连接指示 2 变焦圈 3 对焦圈 4 镜头盖接口指示
5 镜头 6 i-Function 按钮 7 AF/MF 开关 8 OIS 开关
9 变焦锁定开关 0 镜头信息触点
改变焦率)。
4对焦并拍摄相片。
•若想选择在您按下镜头上的 i-Function 按钮时显示的
项目,可使用相机上的 iFn 自定义菜单。
•E 模式中的可用场景或滤镜效果可能会因相机
型号不同而异。
•如果选择 Z ,照片的分辨率将根据变焦率而有
所不同。
使用变焦圈
旋转镜头上的变焦环设置相片的 构图(镜头的焦距)。
由于更改焦距会造成对焦的轻微改变,所以调整变焦 圈
改变焦距后,建议拍照前重新调整对焦。
连接和移除镜头
► 要安装镜头,
1卸下镜头盖、镜头接口盖和机身盖。
2将相机机身红色标记对准镜头红色标记。然后如图
所示旋转镜头,直到其锁定到位。(见图 B)
► 要
卸下镜头,按住镜头释放按钮,然后如图所示旋转镜头。
(见图 C)
锁定变焦(见图 D)
设定变焦锁定以保持镜头视角一致。
若要设置变焦锁,请转动变焦环,直到•焦距达 18 mm,
然后将开关推到左侧。
设置对焦方式
使用光学图像稳定(OIS)功能(见图 E)
将镜头上的 AF/MF 开关置于 AF 或 MF。
通过使用 OIS 功能,用户可以尽可能的减小相机震动。
设定镜头的 OIS 开关设定为 ON。
使用自动对焦 (AF):半按 [快门] 按钮,自动对焦。
相机在使用自动对焦 (AF) 时请勿对镜头前端太过用
力。否则可能会导致镜头故障。
使用镜头遮光罩(见图 F)
使用手动对焦 (MF):可以旋转镜头上的对焦环来手动调整对
焦。
设定 MF 辅助功能以协助手动对焦。有关更多详细信
息,请参阅相机说明书。
若要避免影像画质因不必要的光线遮挡而变差,请使用镜头罩。
在拍摄对象与相机之间距离较近的情况下使用闪光灯,
闪光灯光线可能会被镜头或镜头遮光罩部分遮挡。为确
保获得适当的光照,请卸下镜头遮光罩或调整相机和拍
摄对象之间的距离。
使用 i-Function
使用滤光镜(另购)
按下镜头上的 i-Function 按钮时,可以使用 E 模式或
Z,或者调整某些拍摄选项。在 E 模式中,可以
选择相机支持的场景或滤镜效果。相对于数码变焦,Z 在
放大时照片画质损失更少。只有当您的相机支持此功能时可用。
i-Scene 模式仅适用于部分相机型号。
将滤光镜连接在镜头上之前,请确保滤光镜与镜头兼容。关于兼
容的滤光镜尺寸,请参考“规格”。
•滤光镜是精密的光学设备,注意避免灰尘、污垢和划
伤。 不要将两个或两个以上滤光镜同时安装在镜头
上,否则会损坏图像的质量并造成光晕(镜头的视角被
遮挡造成的图像边缘亮度或饱和度损失)。
•如果使用广角镜头和较厚的滤光镜,影像可能会发暗。
1将模式旋钮旋转到 P、A、S、M 或 i。
2按镜头上的 [i-Function] 选择一个设置。
快门速度
S、M
设置
光圈值
曝光值
白平衡、
ISO
镜头名称
焦距
相当于 35 mm
的焦距
镜头结构-元件
镜头结构-组
非球面元件
ED 元件
查看角度
光圈叶片数
最小焦距(广角)
光圈叶片数
最小焦距(广角)
最小焦距(长焦)
最大放大倍率
镜头遮光罩
光学图像稳定
接口类型
滤光片尺寸
最大直径
长度
重量(仅限镜头,
近似值)
操作温度
操作湿度
SAMSUNG 18-200mm F3.5-6.3 ED OIS
18–200 mm
27.7–308 mm
18
13
3
2
75.9°–8.0°
F3.5–6.3
F22
7
0.5 m
0.5 m
0.28X
附带
是
三星 NX 接口
67 mm
72 mm
105.5 mm
549 g
0–40 °C
5–85%
健康与安全信息
使用镜头前请仔细阅读下列安全注意事项。
•不要通过镜头或相机看太阳。否则可能会严重损伤您的
眼睛。
警告 •使您的镜头或相机远离儿童和宠物。
•不要在未安装镜头盖的情况下,将镜头放在阳光直射的
地方。直射的阳光通过镜头后聚焦在易燃物上可能导致
火灾。
注意 •请仅使用坚固的三脚架。轻型或不稳定的三脚架可能会
倒塌并损坏相机。
镜头的存储和维护
•可用设置可能因拍摄模式不同而异。
拍摄模式
设置
i
E
Z P、A、S、M、i
规格
拍摄模式
A、M
P、A、S
P、A、S、M
•请在干燥、通风的地方存放镜头。
•请勿将镜头存放在温度或湿度过高的区域,或者放置于壁橱、
车辆或存放化学品的密闭区域。
•镜头没有防水功能,在水附近使用时,小心不要弄湿镜头。
•不要使用任何化学药品如稀释剂、酒精或苯擦镜头的灰尘。
•镜头是精密光学设备,小心不要掉落或受到其他物体的撞击。
•避免在温度频繁变化的地方使用镜头,将镜头放在塑料袋或相
机包,防止镜头内外会产生水珠。
•携带或不使用镜头时,请在镜头上装上镜头盖或镜头接口盖,
以免镜头被异物污染或被划伤。
•不要把没带镜头盖的相机放在三脚架上,相机内部零件可能被
直射的阳光损坏。
•为保持镜头性能,每一年或两年检查一次。
•不要对镜头前面施加外力。
•为了安全地使用镜头,请在电源关闭的状态下安装或拆卸镜
头。
•对于使用其他公司镜头造成的任何损坏,三星不承担任何责
任。
•在安装镜头时,确保仅在清洁的环境更换镜头并且不要将手指
伸到镜头接口中。如果有异物进入相机机身或镜头,可能会影
响拍摄效果或导致故障。
•请勿在镜头管的任何部分伸出时运送或存放镜头。 旋转镜头上
的变焦环将镜头管完全缩回机身内。
产品中有害物质的名称及其含量
有害物质
部件名称 铅
汞
镉 六价铬 多溴联苯 多溴二苯醚
(Pb) (Hg) (Cd) (Cr6+) (PBB)
(PBDE)
镜头/LENS ×
○
○
○
○
○
本表格依据 SJ/T 11364 的规定编制
○: 表示该有害物质在该部件所有均质材料中的含量均在
GB/T 26572 规定的限量要求以下。
×: 表示该有害物质至少在该部件的某一均质材料中的含量超
出 GB/T 26572 规定的限量要求。
□ 产品名: 镜头(Lens)
□ 环保使用期限:10年
- 只有按照本产品使用说明书中的方法正常使用
时,环保使用期限才能有效
中国制造 天津三星光电子有限公司
中国 天津津港公路微电子工业区张衡道9号
保留备用
A
B
English
1
2
3
4
5
0
9
8
7
6
Before Using This Device
Thank you for purchasing the Samsung Lens. Update the
firmware of the camera body and lens. Visit www.samsung.com
to download the firmware.
Unpacking
Lens, Lens cap, Lens mount cover, Hood, Case, User manual
•Optional Item: Filter
Layouts (See illustration A)
1 Lens mount index 2 Zoom ring 3 Focus ring
4 Lens hood mount index 5 Lens 6 i-Function button
7 AF/MF switch 8 OIS switch 9 Zoom lock switch
0 Lens information contacts
Attaching and Removing the Lens
C
► To attach the lens,
1 Remove the lens cap, lens mount cover, and body cap.
2 Align the red mark on the lens with the red mark on the
camera body. Then, rotate the lens as shown in the
illustration until it locks into place. (See illustration B)
► To remove the lens, press and hold the lens release
button, and then rotate the lens as shown in the
illustration. (See illustration C)
Setting the Focus Method
D
E
F
Set the AF/MF switch on the lens to AF or MF.
Auto Focus (AF): The focus is adjusted automatically when
you half-press [Shutter].
Do not apply excessive force to the front of the lens while
the camera is using auto focus (AF). Doing so may cause
the lens to malfunction.
Manual Focus (MF): The focus can be adjusted manually by
rotating the focus ring.
Use the MF Assist function on the camera to aid with
manual focusing. Refer to your camera manual for more
details.
Using i-Function
When you press the i-Function button on the lens, you can
use the E mode or Z or adjust some shooting
options. In the E mode, you can select scenes or filter
effects that your camera supports. Z allows you to
zoom in on a subject with less degradation of photo quality
than the Digital zoom. This feature is available only when
your camera supports it. i-Scene mode is available only on
some camera models.
1 Rotate the mode dial to P, A, S, M, or i.
2 Press [i-Function] on the lens to select a setting.
•Available settings may differ depending on the shooting
mode.
Shooting
Shooting
Setting
mode
mode
i
A, M
Aperture value
E
Z P, A, S, M, i Exposure value
P, A, S
White Balance,
Shutter
S, M
P, A, S, M
ISO
speed
3 Rotate the focus ring on the lens to adjust the setting
(or to change the zoom rate in Z mode).
4 Focus and capture the photo.
•To select the items that will appear when you press
the i-Function button on the lens, you can use the iFn
Customizing menu on your camera.
•Available scenes or filter effects in the E mode
may vary depending on the camera model.
•If you select Z, the photo resolution will vary
according to the zoom rate.
Setting
Using the Zoom Ring
Set the composition of the photo (the focal distance of the
lens) by rotating the zoom ring on the lens.
When you use the zoom function, focus can be slightly
changed. Adjust the focus again before you capture a photo.
Locking the zoom (See illustration D)
Set the zoom lock to keep the viewing angle of the lens constant.
To set the zoom lock, turn the zoom ring until the focal
length reaches 18 mm, and then push the switch left.
Using the Optical Image Stabilization (OIS)
Function (See illustration E)
The user can minimize the shaking of camera by using the
OIS function. Set the OIS switch on the lens to ON.
Using a Lens Hood (See illustration F)
To prevent deterioration of image quality by blocking out
unnecessary light, use a lens hood.
When you use a flash in situations where the distance
between the subject and the camera is close, the flash
light may be partially blocked by the lens or a lens hood.
To ensure proper lighting, remove the lens hood or adjust
the distance between the camera and subjects.
Using a Filter (optional)
Before putting a filter on the lens, make sure it is compatible.
Refer to "Specifications" for compatible filter size.
•A filter is a precise optical product. Keep away from
dust, dirt, or scratches. Also, do not try to mount two or
more filters at the same time. Doing so may deteriorate
the image quality and cause vignetting (a reduction of
an image’s brightness or saturation at the periphery as
the viewing angle of the lens is hidden).
•In case of a thick framed filter, the vignetting can occur
with a wide-angle lens.
Specifications
Lens Name
Focal Length
Focal Length in 35 mm
Equivalent
Lens Construction-Elements
Lens Construction-Groups
Aspherical Elements
ED Elements
Angle of View
Maximum Aperture
Minimum Aperture
Number of Diaphragm Blades
Minimum Focus Distance (Wide)
Minimum Focus Distance (Tele)
Maximum Magnification
Lens Hood
Optical Image Stabilizer
Mount Type
Filter Size
Max. Diameter
Length
Weight (Lens Only, Approx.)
Operating Temperature
Operating Humidity
SAMSUNG 18-200mm
F3.5-6.3 ED OIS
18–200 mm
27.7–308 mm
18
13
3
2
75.9°–8.0°
F3.5–6.3
F22
7
0.5 m
0.5 m
0.28X
Included
Yes
Samsung NX Mount
67 mm
72 mm
105.5 mm
549 g
0–40 °C
5–85 %
Health and Safety Information
Please read the following safety tips carefully for proper and
safe use.
•Do not stare at the sun through the lens or camera.
This may cause severe damage to your eyes.
Warning •Keep your lens or camera away from small children
and pets.
•Do not store the lens in direct sunlight without the
lens cap. Direct sunlight that passes through the lens
may combust if it comes into contact with flammable
Caution materials.
•Use only sturdy tripods. Lightweight or unstable tripods
may fall over and damage the camera.
•Do not drop the lens or apply excessive shock to it. The lens is a
precise optical product.
•Avoid using the lens anywhere there is a sudden temperature
change. Keep the lens in a plastic bag or a camera case to prevent
condensation from forming on the inside or outside of the lens.
•When carrying or not using the lens, place the lens cap and lens
mount cover on the lens to prevent contamination from foreign
particles and protect the lens from scratches.
•Do not keep the camera mounted on a tripod without the lens
cap. The inside of the camera can be damaged by direct sunlight.
•Check the lens once every year or two for best performance.
•Do not apply excessive force to the front of the lens.
•For safe use of the lens, mount or dismount the lens while the
camera is turned off.
•Samsung is not responsible for any damage incurred by using
other manufacturers’ lenses.
•Make sure to change lenses only in a clean environment and
do not put your fingers into the lens mount when mounting the
lens. Foreign particles may affect shooting results or cause a
malfunction if they enter the camera body or the lens.
•Do not transport or store the lens with any part of the tube is
extended. Completely retract the lens tube inside the body by
rotating the zoom ring on the lens.
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in countries with separate collection systems)
This marking on the product, accessories or literature indicates that
the product and its electronic accessories (e.g. charger, headset, USB
cable) should not be disposed of with other household waste at the
end of their working life. To prevent possible harm to the environment
or human health from uncontrolled waste disposal, please separate
these items from other types of waste and recycle them responsibly to
promote the sustainable reuse of material resources. Household users
should contact either the retailer where they purchased this product,
or their local government office, for details of where and how they can
take these items for environmentally safe recycling. Business users
should contact their supplier and check the terms and conditions of the
purchase contract. This product and its electronic accessories should
not be mixed with other commercial wastes for disposal.
Lens Storage and Maintenance
•Store the lens in dry and well ventilated areas.
•Do not store the lens in areas of high temperature or humidity or
in a closet, car, or confined area where chemicals are stored.
•The lens is not waterproof. Be careful not to allow it to get wet
when using it near water.
•Do not use chemicals such as thinner, alcohol, or benzene to
remove dust.
Please refer to the warranty that came with your
product or visit our website www.samsung.com for
after-sales service or inquiries.
Download PDF