Samsung | NS048SCREB | Samsung NS024SCREB 사용자 매뉴얼

Features of your new air conditioner
• Cool Summer Offer
On those hot sweltering summer days and long restless nights, there is no better escape
from the heat than the cool comforts of home. Your new air conditioner brings an end to
exhausting hot summer days and lets you rest. This summer, beat the heat with your own
air conditioner.
• Flexible installation
Duct type air conditioner is designed to be slimmer and offers different solutions for any
shape room allowing for specific air flow requirements. Also, the air intake can be set up on
either the bottom or rear of the unit, so there is more flexibility in installation.
For easy future reference, write the model and serial
number down. You will find your model number on the
bottom right side of the air conditioner.
2
Model #
Serial #
Contents
USING PARTS
ENGLISH
Safety precautions ..................................................................................................................................................... 4
Viewing your air conditioner .................................................................................................................................. 8
Using your air conditioner ....................................................................................................................................... 9
Tips on using your air conditioner ...................................................................................................................................................... 9
Cleaning and maintaining the air conditioner ................................................................................................. 10
Cleaning the filter ..................................................................................................................................................................................... 10
Maintaining your air conditioner ...................................................................................................................................................... 11
Appendix . .................................................................................................................................................................. 12
Troubleshooting . ...................................................................................................................................................................................... 12
Operation ranges ...................................................................................................................................................................................... 13
INSTALLATION PARTS
Safety precautions.................................................................................................................................................... 14
Selecting the installation location........................................................................................................................ 16
Indoor unit installation . ......................................................................................................................................... 21
Purging the unit........................................................................................................................................................ 22
Connecting the refrigerant pipe........................................................................................................................... 23
Cutting/flaring the pipes......................................................................................................................................... 24
Performing leak test & insulation......................................................................................................................... 25
Drain pipe and drain hose installation................................................................................................................ 27
Wiring work................................................................................................................................................................ 30
Adjusting air flow...................................................................................................................................................... 33
Setting up the mode option................................................................................................................................... 34
Assigning address to indoor unit . ....................................................................................................................... 37
Additional functions................................................................................................................................................ 38
Final check and Providing information for user................................................................................................ 39
Troubleshooting . ..................................................................................................................................................... 40
3
USING PARTS
Safety precautions
A
Before using your new air conditioner, please read this manual thoroughly to ensure that you know how to
safely and efficiently operate the extensive features and functions of your new appliance.
Because the following operating instructions cover various models, the characteristics of your air conditioner
may differ slightly from those described in this manual. If you have any questions, call your nearest contact
center or find help and information online at www.samsung.com.
Important safety symbols and precautions:
WARNING
Hazards or unsafe practices that may result in severe personal injury or death.
CAUTION
Hazards or unsafe practices that may result in minor personal injury or
property damage.
Follow directions.
Do NOT attempt.
Make sure the machine is grounded to prevent electric shock.
Unplug the power plug from the wall socket.
Do NOT disassemble.
FOR INSTALLATION
WARNING
Plug the power cord into a wall socket with the power specifications of the product or higher and use the
socket for this appliance only. In addition, do not use an extension cord.
Sharing a wall socket with other appliances using a power strip or extending the power cord may result in
electric shock or fire.
 Do not use an electric transformer. It may result in electric shock or fire.
 If the voltage/frequency/rated current condition is different, it may cause fire.
The installation of this appliance must be performed by a qualified technician or service company.
 Failing to do so may result in electric shock, fire, explosion, problems with the product, or injury.
Install a switch and circuit breaker dedicated to the air conditioner.
 Failing to do so may result in electric shock or fire.
Fix the outdoor unit firmly so that the electric part of the outdoor unit is not exposed.
 Failing to do so may result in electric shock or fire.
Do not install this appliance near a heater, inflammable material. Do not install this appliance in a humid,
oily or dusty location, in a location exposed to direct sunlight and water (rain drops). Do not install this
appliance in a location where gas may leak.
 This may result in electric shock or fire.
Never install the outdoor unit in a location such as on a high external wall where it could fall.
 If the outdoor unit falls, it may result in injury, death or property damage.
This appliance must be properly grounded. Do not ground the appliance to a gas pipe, plastic water pipe,
or telephone line.
 Failure to do so may result in electric shock, fire, an explosion, or other problems with the product.
 Never plug the power cord into a socket that is not grounded correctly and make sure that it is in accordance with
local and national codes.
FOR INSTALLATION
CAUTION
This appliance should be positioned in such a way that it is accessible to the power plug.
 Failing to do so may result in electric shock or fire due to electric leakage.
Install your appliance on a level and hard floor that can support its weight.
 Failing to do so may result in abnormal vibrations, noise, or problems with the product.
4
FOR INSTALLATION
CAUTION
Install the draining hose properly so that water is drained correctly.
ENGLISH
 Failing to do so may result in water overflowing and property damage.
When installing the outdoor unit, make sure to connect the draining hose so that draining is performed
correctly.
 The water generated during the heating operation by the outdoor unit may overflow and result in property damage. In
particular, in winter, if a block of ice falls, it may result in injury, death or property damage.
FOR POWER SUPPLY
WARNING
Remove all foreign substances such as dust or water from the power plug terminals and contact points
using a dry cloth on a regular basis.
 Unplug the power plug and clean it with a dry cloth.
 Failing to do so may result in electric shock or fire.
Plug the power plug into the wall socket in the right direction so that the cord runs towards the floor.
 If you plug the power plug into the socket in the opposite direction, the electric wires within the cable may be
damaged and this may result in electric shock or fire.
When the appliance or power plug or power cord is damaged, contact your nearest service center.
Plug the power plug into the wall socket firmly. Do not use a damaged power plug, damaged power cord
or loose wall socket.
 This may result in electric shock or fire.
Do not pull the power cord, when unplugging the power plug.
 Unplug the power plug by holding the plug.  Failing to do so may result in electric shock or fire.
Do not pull or excessively bend the power cord. Do not twist or tie the power cord. Do not hook the
power cord over a metal object, place a heavy object on the power cord, insert the power cord between
objects, or push the power cord into the space behind the appliance.
 This may result in electric shock or fire.
FOR POWER SUPPLY
CAUTION
When not using the air conditioner for a long period of time or during a thunder/lightning storm, cut the
power at the circuit breaker.
 Failing to do so may result in electric shock or fire.
FOR USING
WARNING
If the appliance is flooded, please contact your nearest service center.
 Failing to do so may result in electric shock or fire.
If the appliance generates a strange noise, a burning smell or smoke, unplug the power plug immediately
and contact your nearest service center.
 Failing to do so may result in electric shock or fire.
In the event of a gas leak (such as propane gas, LP gas, etc.), ventilate immediately without touching the
power plug. Do not touch the appliance or power cord.
 Do not use a ventilating fan.
 A spark may result in an explosion or fire.
To reinstall the air conditioner, please contact your nearest service center.
 Failing to do so may result in problems with the product, water leakage, electric shock, or fire.
 A delivery service for the product is not provided. If you reinstall the product in another location, additional
construction expenses and an installation fee will be charged.
 Especially, when you wish to install the product in an unusual location such as in an industrial area or near the seaside
where it is exposed to the salt in the air, please contact your nearest service center.
5
A
Safety
precautions
FOR USING
WARNING
Do not touch the power plug or the circuit breaker with wet hands.
 This may result in electric shock.
Do not unplug the power plug or turn the air conditioner off with the circuit breaker while it is operating.
 Plugging the power plug into the wall outlet or turning the air conditioner on from the circuit breaker may cause a
spark and result in electric shock or fire.
After unpacking the air conditioner, keep all packaging materials well out of the reach of children, as
packaging materials can be dangerous to children.
 If a child places a bag over its head, it may result in suffocation.
Do not insert your fingers or foreign substances into the air inlet/outlet of the air conditioner.
 Take special care that children do not injure themselves by inserting their fingers into the product.
Do not strike or pull the air conditioner with excessive force.
 This may result in fire, injury, or problems with the product.
Do not place an object near the outdoor unit that allows children to climb onto the machine.
 This may result in children seriously injuring themselves.
Do not use this air conditioner for long periods of time in badly ventilated locations or near infirm people.
 Since this may be dangerous due to a lack of oxygen, Open a window at least once an hour.
If any foreign substance such as water has entered the appliance, cut the power by unplugging the power
plug and turning the circuit breaker off and then contact your nearest service center.
 Failing to do so may result in electric shock or fire.
Do not attempt to repair, disassemble, or modify the appliance yourself.
 Do not use any fuse (such as cooper, steel wire, etc.)other than the standard fuse.
 Failing to do so may result in electric shock, fire, problems with the product, or injury.
FOR USING
CAUTION
Do not place objects or devices under the indoor unit.
 Water dripping from the indoor unit may result in fire or property damage.
Check that the installation frame of the outdoor unit is not broken at least once a year.
 Failing to do so may result in injury, death or property damage.
Max current is measured according to IEC standard for safety and current is measured according to ISO
standard for energy efficiency.
Do not stand on top of the appliance or place objects (such as laundry, lighted candles, lighted cigarettes,
dishes, chemicals, metal objects, etc.) on the appliance.
 This may result in electric shock, fire, problems with the product, or injury.
Do not operate the appliance with wet hands.
 This may result in electric shock.
Do not spray volatile material such as insecticide onto the surface of the appliance.
 As well as being harmful to humans, it may also result in electric shock, fire or problems with the product.
Do not drink the water from the air conditioner.
 The water may be harmful to humans.
Do not apply a strong impact to the remote controller and do not disassemble the remote controller.
Do not touch the pipes connected with the product.
 This may result in burns or injury.
6
FOR USING
CAUTION
ENGLISH
Do not use this air conditioner to preserve precision equipment, food, animals, plants or cosmetics, or for
any other unusual purposes.
This may result in property damage.
Avoid directly exposing humans, animals or plants from the air flow from the air conditioner for long
periods of time.
This may result in harm to humans, animals or plants.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety. Children should be
supervised to ensure that they do not play with the appliance.
FOR CLEANING
WARNING
Do not clean the appliance by spraying water directly onto it. Do not use benzene, thinner or alcohol to
clean the appliance.
This may result in discoloration, deformation, damage, electric shock or fire.
Before cleaning or performing maintenance, unplug the air conditioner from the wall socket and wait
until the fan stops.
Failing to do so may result in electric shock or fire.
FOR CLEANING
CAUTION
Take care when cleaning the surface of the heat exchanger of the outdoor unit since it has sharp edges.
To avoid cutting your fingers, wear thick cotton gloves when cleaning it.
Do not clean the inside of the air conditioner by yourself.
For cleaning inside the appliance, contact your nearest service center.
When cleaning the internal filter, refer to the descriptions in the
‘Cleaning and maintaining the air conditioner’ section.
Failure to do may result in damage, electric shock or fire.
7
Viewing your air conditioner
Congratulations on the purchase of the air conditioner. We hope you enjoy the features of your air
conditioner and stay cool or warm with optimal efficiency.
Please read the user manual to get started and to make the best use of the air conditioner.
Air filter (the return air side)
Ceiling
Air intake
Air outlet
Your air conditioner may slightly look different from illustration shown above depending on
your model, Air Filter application is as below table.
8
Using your air conditioner
Tips on using air conditioner
Here are some tips that you would follow when using your air conditioner.
RECOMMENDATION
Cooling
• If current outside temperatures are much higher than the selected indoor
temperature, it may take time to bring the inner temperature to the desired
coolness.
• Avoid drastically turning down the temperature.
Energy is wasted and the room does not cool faster.
Power failure
• If a power failure occurs during the operation of the air conditioner, the
operating immediately stops and unit will be off. When power returns, the
air conditioner will run automatically.
Protection
mechanism
• If the air conditioner has just been turned on after operation stops or being
plugged in, cool/warm air does not come out for 3 minutes to protect the
compressor of the outdoor unit.
ENGLISH
TOPIC
9
Cleaning and maintaining the air conditioner
For the best performance from your air conditioner, clean it periodically. When cleaning, make sure to
unplug from the unit for user’s safety.
CLEANING THE FILTER
When cleaning the filter, make sure to unplug the power from the unit. Washable foam based Air filter
captures large particles from the air. The filter is cleaned with a vacuum or by hand washing.
1. Slide out the Air filter on the rear side panel to the right side.
2. Clean the Air filter with a vacuum cleaner or soft brush. If dust is too heavy, then rinse it with
running water and dry it in a ventilated area.
• For best conditions, repeat every two weeks.
• If the Air filter dries in a confined (or humid) area, odors may generate. If it occurs,
re-clean and dry it in a ventilated area.
3. Insert the Air filter back in its original position.
 The designs and shape are subject to change according to the model.
• The illustration shown above may differ from your depending on your model.
• After cleaning the filter, press the Filter Reset button on the remote control for 2 seconds to
reset the filler schedule. Filter sign indicator will be on for cleaning time.
10
MAINTAINING YOUR AIR CONDITIONER
1. Dry the air conditioner thoroughly by operating in Fan mode for 3 to 4 hours and disconnect
the power plug. There may be internal damage if moisture is left in components.
2. Before using the air conditioner again, dry the inner components of the air conditioner again by
running in Fan mode for 3 to 4 hours. This helps remove odors which may have generated from
dampness.
Periodical checks
Refer to the following chart to maintain the air conditioner properly.
Type
Description
Clean the air filter (1)
Indoor
unit
Monthly
Every 4
months

Clean the condensate drain pan (2)

Thoroughly clean the heat exchanger (2)

Clean the condensate drain pipe (2)

Replace the remote control batteries (1)
Clean the heat exchanger on the outside of the
unit (2)
Outdoor
unit
Once a
year


Clean the heat exchanger on the inside of
the unit (2)

Clean the electric components with jets of
air (2)

Verify that all the electric components are firmly
tightened (2)

Clean the fan (2)

Verify that all the fan assembly is firmly
tightened (2)

Clean the condensate drain pan (2)

The checks and maintenance operations described are essential to guarantee the
efficiency of the air conditioner. The frequency of these operations varies according to the
characteristics of the area, the amount of dust, etc.
(1) The described operations should be performed more frequently if the area of
installation is very dusty.
(2) These operations must always be performed by qualified personnel. For more detailed
information, see the Installation Manual.
11
ENGLISH
If the air conditioner will not be used for an extended period of time, dry the air conditioner to maintain it
in best condition.
Cleaning and maintaining the air conditioner
MAINTAINING YOUR AIR CONDITIONER
Internal protections via the unit control system
This internal protection operates if an internal fault occurs in the air conditioner.
Type
Description
Anti-protection of
internal battery
The compressor will be off to protect internal battery when the air conditioner
operates in Cool mode.
Protect
compressor
The air conditioner does not start operating immediately to protect the compressor of the outdoor unit after it has been started.
Appendix
TROUBLESHOOTING
Refer to the following chart if the air conditioner operates abnormally. This may save time and
unnecessary expenses.
PROBLEM
SOLUTION
The air conditioner does not
operate immediately after it has
been restarted.
The air conditioner does not work
at all.
• Because of the protective mechanism, the appliance does not start operating
immediately to keep the unit from overloading.
The air conditioner will start in 3 minutes.
• Check that the power plug is properly connected. Insert the power plug into the wall
socket correctly.
• Check if the circuit breaker is switched off.
• Check if there is a power failure.
• Check your fuse. Make sure it is not blown out.
• Check if you selected Fan mode.
Press the Mode button on the remote control to select another mode.
• Check if the set temperature is higher (lower) than the current temperature. Press the
Temperature button on the remote control to change the set temperature. Press the
Temperature button to decrease or increase the temperature.
• Check if the air filter is blocked by dirt.
• Check if the air conditioner has just been turned on. If so, wait 3 minutes. Cool air does
not come out to protect the compressor of the outdoor unit.
The temperature does not change.
The cool air does not come out of
the air conditioner.
12
Appendix
SOLUTION
The cool air does not come out of
the air conditioner.
• Check if the air conditioner is installed in a place with a direct exposure to sunlight.
Hang curtains on windows to boost cooling efficiency.
• Check if the cover or any obstacle is not near the outdoor unit.
• Check if the refrigerant pipe is too long.
• Check if the air conditioner is only available in Cool mode.
• Check if the remote control is only available for cooling model.
• Check if you selected Auto or Dry mode.
The air conditioner automatically adjusts the fan speed to Auto in Auto/Dry mode.
• Check if you press the Power button on the remote control after you have set the time.
• Check if the appliance is running in a smoky area or if there is a smell entering from
outside. Operate the air conditioner in Fan mode or open the windows to air out the
room.
• A bubbling sound may be heard when the refrigerant is circulating through the
compressor. Let the air conditioner operate in a selected mode.
• When you press the Power button on the remote control, noise may be heard from the
drain pump inside the air conditioner.
• Check if the air conditioner has been cooling for an extended period of time with the
air flow blades pointed downwards. Condensation may generate due to the difference
in temperature.
• Check if your batteries are depleted.
• Make sure batteries are correctly installed.
• Make sure nothing is blocking your remote control sensor.
• Check that there are strong lighting apparatus near the air conditioner. Strong light
which comes from fluorescent bulbs or neon signs may interrupt the electric waves.
• Check if you set the wired remote control for group control.
The fan speed does not change.
Timer function does not set.
Odors permeate in the room
during operation.
The air conditioner makes a
bubbling sound.
Water is dripping from the air flow
blades.
Remote control is not working.
The air conditioner does not turn
on or off with the wired remote
control.
The wired remote control does not
operate.
The indicators of the digital display
flashes.
• Check if TEST indicator is displayed on the wired remote control. If so, turn off the unit
and switch off the circuit breaker. Call your nearest contact center.
• Press the Power button on the remote control to turn the unit off and switch the
circuit breaker off. Then, switch it on again.
OPERATION RANGES
The table below indicates the temperature and humidity ranges the air conditioner can be operated
within. Refer to the table for efficient use.
MODE
COOLING
DRYING
OPERATIONAL TEMPERATURE
INDOOR
21˚C to 32˚C
21˚C to 32˚C
OUTDOOR
21˚C to 54˚C
21˚C to 54˚C
INDOOR
HUMIDITY
IF OUT OF CONDITIONS
80%
or less
Condensation may occur on the
indoor unit with risk to have either
water blow off or drops on the
floor.
-
Condensation may occur on the
indoor unit with risk to have either
water blow off or drops on the
floor.
If the cooling operation is used at over 32˚C (indoor temperature), it does not cool at its full capacity.
13
ENGLISH
PROBLEM
INSTALLATION PARTS
Safety precautions
(Carefully follow the precautions listed below because they are essential to guarantee the safety of the
equipment.)
WARNING
 Always disconnect the air conditioner from the power supply before servicing it or
accessing its internal components.
 Verify that installation and testing operations are performed by qualified personnel.
 Verify that the air conditioner is not installed in an easily accessible area.
General information
 Carefully read the content of this manual before installing the air conditioner and store the manual in a safe place in
order to be able to use it as reference after installation.
 For maximum safety, installers should always carefully read the following warnings.
 Store the operation and installation manual in a safe location and remember to hand it over to the new owner if the
air conditioner is sold or transferred.
 This manual explains how to install an indoor unit with a split system with two SAMSUNG units. The use of other types
of units with different control systems may damage the units and invalidate the warranty. The manufacturer shall not
be responsible for damages arising from the use of non compliant units.
 The air conditioner is compliant with the requirements of the Low Voltage Directive (72/23/EEC),
the EMC Directive (89/336/EEC) and the Directive on pressurized equipment (97/23/EEC).
 The manufacturer shall not be responsible for damage originating from unauthorized changes or the improper connection
of electric and hydraulic lines. Failure to comply with these instructions or to comply with the requirements set forth in the
“Operating limits” table, included in the manual, shall immediately invalidate the warranty.
 The air conditioner should be used only for the applications for which it has been designed: the indoor unit is not
suitable to be installed in areas used for laundry.
 Do not use the units if damaged. If problems occur, switch the unit off and disconnect it from the power supply.
 In order to prevent electric shocks, fires or injuries, always stop the unit, disable the protection switch and contact
SAMSUNG’s technical support if the unit produces smoke, if the power cable is hot or damaged or if the unit is very noisy.
 Always remember to inspect the unit, electric connections, refrigerant tubes and protections regularly.
These operations should be performed by qualified personnel only.
 The unit contains moving parts, which should always be kept out of the reach of children.
 Do not attempt to repair, move, alter or reinstall the unit. If performed by unauthorized personnel, these operations
may cause electric shocks or fires.
 Do not place containers with liquids or other objects on the unit.
 All the materials used for the manufacture and packaging of the air conditioner are recyclable.
 The packing material and exhaust batteries of the remote control(optional) must be disposed of in accordance with
current laws.
 The air conditioner contains a refrigerant that has to be disposed of as special waste. At the end of its life cycle, the air
conditioner must be disposed of in authorized centers or returned to the retailer so that it can be disposed of correctly
and safely.
Installing the unit
IMPORTANT: When installing the unit, always remember to connect first the refrigerant tubes, then the electrical lines.
Always disassemble the electric lines before the refrigerant tubes.
 Upon receipt, inspect the product to verify that it has not been damaged during transport. If the product appears
damaged, DO NOT INSTALL it and immediately report the damage to the carrier or retailer (if the installer or the
authorized technician has collected the material from the retailer.)
 After completing the installation, always carry out a functional test and provide the instructions on how to operate
the air conditioner to the user.
 Do not use the air conditioner in environments with hazardous substances or close to equipment that release free
flames to avoid the occurrence of fires, explosions or injuries.
 The air conditioner should be used only for the applications for which it has been designed: the indoor unit is not
suitable to be installed in areas used for laundry.
14
Power supply line, fuse or circuit breaker
 Always make sure that the power supply is compliant with current safety standards. Always install the air conditioner in
compliance with current local safety standards.
 Always verify that a suitable grounding connection is available.
 Verify that the voltage and frequency of the power supply comply with the specifications and that the installed power is
sufficient to ensure the operation of any other domestic appliance connected to the same electric lines.
 Always verify that the cut-off and protection switches are suitably dimensioned.
 Verify that the air conditioner is connected to the power supply in accordance with the instructions provided in the
wiring diagram included in the manual.
 Always verify that electric connections (cable entry, section of leads, protections…) are compliant with the electric
specifications and with the instructions provided in the wiring scheme. Always verify that all connections comply with
the standards applicable to the installation of air conditioners.
CAUTION
 Make sure that you earth the cables.
- Do not connect the earth wire to the gas pipe, water pipe, lighting rod or telephone wire.
If earthing is not complete, electric shock or fire may occur.
 Install the circuit breaker.
- If the circuit breaker is not installed, electric shock or fire may occur.
 Make sure that the condensed water dripping from the drain hose runs out properly and safely.
 Install the power cable and communication cable of the indoor and outdoor unit at least 1m
away from the electric appliance.
 Install the indoor unit away from lighting apparatus using the ballast.
- If you use the wireless remote control, reception error may occur due to the ballast of the
lighting apparatus.
 Do not install the air conditioner in following places.
- Place where there is mineral oil or arsenic acid.
Resin parts flame and the accessories may drop or water may leak.
The capacity of the heat exchanger may reduce or the air conditioner may be out of order.
- The place where corrosive gas such as sulfurous acid gas generates from the vent pipe or air
outlet.
The copper pipe or connection pipe may corrode and refrigerant may leak.
- The place where there is a machine that generates electromagnetic waves.
The air conditioner may not operate normally due to control system.
- The place where there is a danger of existing combustible gas, carbon fiber or flammable
dust.
The place where thinner or gasoline is handled.
Gas may leak and it may cause fire.
15
ENGLISH
 Our units must be installed in compliance with the spaces indicated in the installation manual to ensure either
accessibility from both sides or ability to perform routine maintenance and repairs. The units’ components must be
accessible and that can be disassembled in conditions of complete safety either for people or things.
For this reason, where it is not observed as indicated into the Installation Manual, the cost necessary to reach and repair
the unit (in safety, as required by current regulations in force) with slings, trucks, scaffolding or any other means of
elevation won’t be considered in-warranty and charged to end user.
Selecting the installation location
A
The following accessories are supplied with the indoor unit.
The type and quantity may differ depending on the specifications.
Accessories
User & Installation
manual
Flexible hose
Thermal insulation Thermal insulation
sponge B
sponge C
Insulation drain Thermal insulation
sponge A
Clamp hose
Rubber
Cable-tie
Wired remote control accessories
Wired remote
control(1)
Cable-tie(2)
Indoor unit power Communication
drawing cable (1) cable of the wired
remote control (1)
Cable clamp(4)
M4x16
tapped screw(5)
Wire joint(4)
User’s
manual (1)
Installation
manual (1)
Indoor Unit
There must be no obstacles near the air inlet and outlet.
Install the indoor unit on a ceiling that can support its weight.
Maintain sufficient clearance around the indoor unit.
Make sure that the water dripping from the drain hose runs away correctly and safely.
 The indoor unit must be installed in this way, that they are out of public access. (Not touchable by the users)
After connecting a chamber, insulate the connection part between the indoor unit and the chamber with t10 or thicker insulation. Otherwise, there can be air leak or dew from the connection part.
Rigid wall without vibration.
Where it is not exposed to direct sunshine.
Where the air filter can be removed and cleaned easily.
16
Space requirements for installation & service
Unit Depth(D)+50mm
ENGLISH
 Construction Standard for Inspection Hole.
1) In case, the ceiling is textile, Inspection hole dose not need.
2) In case, the ceiling is plaster board, Inspection hole depends on Inside height of the ceiling.
a. Height is more than 1m : Only “B” [Inspection for PBA] is applied.
b. Height is less than 1m : Both “A” & ”B” are applied.
c. “A” & ”B” are inspection holes.
Unit Width(W)
“A”=W+100mm
“B”=500mm
20mm or more
20mm or more
 You must have 20mm or more space between the ceiling and the bottom of indoor unit. Otherwise, the noise from
the vibration of indoor unit may bother the user.When the ceiling is under construction, the hole for check-up must
be made to take service, clean and repair the unit.
 It is possible to install the unit at an height of between 2.2~2.5m from the ground, if the unit has a duct with a well
defined lenght (300mm or more), to avoid fan motor blower contact.
 If you install the cassette or duct type indoor unit on the ceiling with humidity over 80%, you must apply extra
10mm of polyethylene foam or other insulation with similar material on the body of the indoor unit.
Insulation Guide
B
D
Back
Front
A
Thickness: more than 10mm
Indoor Unit
900x480x260
A
900x480
B
900x480
C
480x260
1150x480x320
1150x480
1150x480
480x320
1200x650x360
1200x650
1200x650
MA duct
C
D
Front/Back
480x260 Insulate the front and back side in
480x320 proper size at the same time when
insulating the suction duct and
650x360 discharge duct.
650x360
 Insulate the end of the pipe and some curved area by using separate insulator.
 Insulate the discharge and suction part at the same time when you insulate connection duct.
17
Selecting the installation location
A
Drawing of the indoor unit
NS012SCRE
NS018SCRE
NS024SCRE
Unit:mm
397 (Suspension position)
1000
900
87
500
97
900
7
135x5=675
844 (Air outlet duct flange)
6
936 (Suspension position)
530
480
8
222
77
117
Discharge side
185
90
260
Inspection hole
2
1
5
No.
18
4
3
Suction side
76
132
139
Name
1
Liquid pipe connection
2
Gas pipe connection
3
4
5
6
7
8
Drain pipe connection
Drain pipe connection
Power supply connection
Air discharge flange
Air filter
Hook
Description
ø6.35(1/4")
ø9.52(3/8")(012);
ø12.70(1/2")(018);
ø15.88(5/8")(024);
OD25 ID20(without drain pump)
Using drain pump (Optional)
M8~M10
12
NS036SCRE
ENGLISH
Unit:mm
500
102
1150
1250
530
Inspection hole
No.
Name
Description
1
2
3
4
5
6
7
8
Liquid pipe connection
Gas pipe connection
Drain pipe connection
Drain pipe connection
Power supply connection
Air discharge flange
Air filter
Hook
ø9.52(3/8")
ø15.88(5/8")
OD25 ID20(without drain pump)
Using drain pump (Optional)
M8~M10
19
Selecting the installation location
A
Drawing of the indoor unit
NS048SCRE
NS060SCRE
Unit:mm
700
650
1300
500
102
1200
1000(Air outlet duct flange)
1236(Suspension position)
534(Suspension position)
Discharge side
Suction side
Inspection hole
20
No.
Name
Description
1
2
3
4
5
6
7
8
Liquid pipe connection
Gas pipe connection
Drain pipe connection
Drain pipe connection
Power supply connection
Air discharge flange
Air filter
Hook
ø9.52(3/8")
ø19.05(3/4")
OD25 ID20(without drain pump)
Using drain pump (Optional)
M8~M10
Indoor unit installation
A
1
Place the pattern sheet on the ceiling at the spot where
you want to install the indoor unit.
ENGLISH
NoteSince the diagram is made of paper, it may
shrink or stretch slightly due to temperature
or humidity. For this reason, before drilling
the holes maintain the correct dimensions
between the markings.
Concrete
2
3
Insert bolt anchors, use existing ceiling supports or
construct a suitable support as shown in figure.
Install the suspension bolts depending on the ceiling
type.
CAUTION
4
Hole in anchor
Hole in plug
Suspension bolt( 3/8” or M10)
Ceiling support
Screw eight nuts to the suspension bolts making space
for hanging the indoor unit.
CAUTION
5
 Ensure that the ceiling is strong enough to
support the weight of the indoor unit.
Before hanging the unit, test the strength
of each attached suspension bolt.
 If the length of suspension bolt is more
than 1.5m, it is required to prevent vibration.
 If this is not possible, create an opening on
the false ceiling in order to be able to use it
to perform the required operations on the
indoor unit.
Insert
 You must install the suspension bolts more
than four when installing the indoor unit.
Hang the indoor unit to the suspension bolts between
two nuts.
NotePiping must be laid and connected inside
the ceiling when suspending the unit. If the
ceiling is already constructed, lay the piping
into position for connection to the unit
before placing the unit inside the ceiling.
6
Screw the nuts to suspend the unit.
7
Adjust level of the unit by using measurement plate for
all 4 sides.
NoteFor proper drainage of condensate, give a
'A' slant to the left or right side of the unit
which will be connected with the drain hose,
as shown in the figure. Make a tilt when you
wish to install the drain pump, too.
Rubber
3mm
Drain hose port
21
Purging the unit
On delivery, the indoor unit is loaded with inert gas.
All this gas must therefore be purged before connecting the
assembly piping. To purge the inert gas, proceed as follows.
Unscrew the pinch pipe at the end of each refrigerant pipe.
Result: All inert gas escapes from the indoor unit.
NoteTo prevent dirt or foreign objects from getting
into the pipes during installation, do NOT remove
the pinch pipe completely until you are ready to
connect the piping.
 The designs and shape are subject to
change according to the model.
22
Connecting the refrigerant pipe
The connection procedure for the refrigerant pipes varies
according to the exit position of the pipes from the indoor unit, as
seen when facing the indoor in the “A” side.
 Liquid refrigerant port
 Gas refrigerant port
 Drain hose port
1
Remove the pinch pipe on the pipes and connect the
assembly pipes to each pipe, tightening the nuts, first
manually and then with a torque wrench, a spanner applying
the following torque.
Outer Diameter
6.35 mm (1/4")
9.52 mm (3/8")
12.70 mm (1/2")
15.88 mm (5/8")
19.05 mm (3/4")
Torque (kgf•cm)
145~175
333~407
505~615
630~769
990~1210
NoteMust apply refrigerant oil on the flaring area to
prevent a leak.
2
Refrigerant oil
ENGLISH
There are two refrigerant pipes of differing diameters:
 A smaller one for the liquid refrigerant
 A larger one for the gas refrigerant
 The inside of copper pipe must be clean & has no dust.
Torque wrench
Spanner
Flare nut
Union
Liquid
refrigerant port
Gas refrigerant port
Drain hose connection port
Be sure that there must be no crack or kink on the bended area.
 The designs and shape are subject to change
according to the model.
23
Cutting/flaring the pipes
1
Make sure that you prepared the required tools.
(pipe cutter, reamer, flaring tool and pipe holder)
2
If you want to shorten the pipe, cut it using a pipe cutter ensuring that
the cut edge remains at 90° with the side of the pipe. There are some
examples of correctly and incorrectly cut edges below.
Oblique
Rough
Burr
3
To prevent a gas leak, remove all burrs at the cut edge of the pipe using a
reamer.
4
Carry out flaring work using flaring tool as shown below.
A
Flaring tool
York
Die
Die
Clutch type
Wing nut type
Outer diameter
(mm)
Flare tool for
R22 clutch type
6.35
9.52
12.70
15.88/19.05
5
0~0.5
0~0.5
0~0.5
0~0.5
Flare nut
Copper
pipe
A(mm)
Conventional flare tool
Clutch type
Wing nut type
1.0~1.5
1.5~2.0
1.0~1.5
1.5~2.0
1.0~1.5
1.5~2.0
1.0~1.5
1.5~2.0
Check if you flared the pipe correctly. There are some examples of
incorrectly flared pipes below.
Inclined
6
Copper pipe
Damaged Surface Cracked
Uneven Thickness
Align the pipes and tighten the flare nuts first manually and then with a
torque wrench, applying the following torque.
Outer diameter (mm)
6.35
9.52
12.70
15.88
19.05
Connection
Torque(kgf•cm)
145~175
333~407
505~615
630~769
990~1210
CAUTION
24
In case of needing brazing, you must work with Nitrogen gas blowing.
Performing leak test & insulation
Leak test
ENGLISH
LEAK TEST WITH NITROGEN (before opening valves)
In order to detect basic refrigerant leaks, before recreating the
vacuum and recirculating the R22, it’s responsible of installer
to pressurize the whole system with nitrogen (using a pressure
regulator) at a pressure above 4.1MPa (gauge).
Leak check
LEAK TEST WITH R22 (after opening valves)
Before opening valves, discharge all the nitrogen into the system
and create vacuum. After opening valves check leaks using a
leak detector for refrigerant R22.
CAUTION
Discharge all the nitrogen to create a vacuum and
charge the system.
 The designs and shape are subject to change
according to the model.
Insulation
Once you have checked that there are no leaks in the system,
you can insulate the piping and hose.
1
No gap
To avoid condensation problems, place T13.0 or thicker
Acrylonitrile Butadien Rubber separately around each
refrigerant pipe.
NBR(T13.0 or thicker)
NoteAlways make the seam of pipes face upwards.
Insulation cover pipe
2
Insulation pipe
Wind insulating tape around the pipes and drain hose
avoiding to compress the insulation too much.
Indoor unit
3
Finish wrapping insulating tape around the rest of the
pipes leading to the outdoor unit.
Be sure to overlap
the insulation
4
The pipes and electrical cables connecting the indoor
unit with the outdoor unit must be fixed to the wall with
suitable ducts.
CAUTION
Must fit tightly against body
without any gap.
CAUTION
All refrigerant connection must be accessible, in order
to permit either unit maintenance or removing it
completely.
25
Performing leak test & insulation
5 Select the insulator of the refrigerant pipe.
Insulate the gas side and liquid side pipe referring to the thickness according to the pipe size.
 Indoor temperature of 30°C and humidity of 85% is the standard condition. If installing in a high
humidity condition, use one grade thicker insulator by referring to the table below.
If installing in an unfavorable conditions, use thicker one.
Insulator’s heat-resistance temperature should be more than 120°C.
Pipe
Pipe size
Liquid
pipe
Ø6.35 ~ Ø9.52
Ø12.7 ~ Ø50.80
Ø6.35
Ø9.52
Ø12.70
Ø15.88
Ø19.05
Ø22.23
Ø25.40
Ø28.58
Ø31.75
Ø38.10
Ø44.45
Ø50.80
Gas
pipe
Insulation Type (Heating/Cooling)
Standard
High humidity
[30°C, 85%]
[30°C, over 85%]
EPDM, NBR
9t

13t

13t
19t
25t
19t
Remarks
Internal temperature
is higher than 120°C
32t
25t
Refrigerant pipe
You can contact the gas side and liquid side pipes but the
pipes should not be pressed.
When contacting the gas side and gas side pipe, use 1 grade
thicker insulator.
38t
Insulation
Insulation
Liquid pipe
Gas pipe
CAUTION
 Install the insulation not to get wider and use the adhesives on the connection part of it to prevent
moisture from entering.
 Wind the refrigerant pipe with insulation tape if it is exposed to outside sunlight.
 Install the refrigerant pipe respecting that the insulation does not get thinner on the bent part or
hanger of pipe.
 Add the additional insulation if the insulation plate gets thinner.
Hanger
Additional insulation
a
a×3
26
Refrigerant pipe insulation
Drain pipe and drain hose installation
Care must be taken when installing the drain hose for the indoor unit to ensure that any condensate water is correctly drained outside.
ENGLISH
1
Installing the drain hose should be the shorter, the better.
 In order to discharge condensation water, the drain hose should keep tilted.
 Fix the drain hose with Cable-Tie, so that it will not separate from the machine.
 While using draining pump, connect the end with draining pump.
2
Insulate and fix the drain hose according to the figure.
 Insert the drain hose to bottom of the outfall of water basin.
 Lock steel ring of the drain hose according to the figure.
 Wind and wrap steel ring and drain hose fully with thermal insulation sponge; fix both ends
of external layer with ribbon for thermal insulation.
 After being installed, drain hose must be insulated fully by heat insulating material. (To be
provided at site.)
Fix with Cable-Tie
Indoor unit
Steel ring of drain hose
Joint of drain hose
Drain hose
A-A’
Drain hose
As shown in the figure,
tighten steel ring of the
drain hose.
Wrap thermal sleeve hose
27
Drain pipe and drain hose installation
Drainpipe Connection
Without the drain pump
1
Install horizontal drainpipe with a slope of 1/100 or more and fix it by hanger space of 1.0~1.5m.
2
Install U-trap at the end of the drainpipe to prevent a nasty smell to reach the indoor unit.
3
Do not install the drainpipe to upward position. It may cause water flow back to the unit.
1~1.5m
Hanger
Flexible hose
Horizontal drainpipe
more than 1/100 slope
Ceiling
With the drain pump
1
The drain pipe should be installed within 300mm to 550mm from the flexible hose and then lift
down 20mm or more.
2
Install horizontal drainpipe with a slope of 1/100 or more and fix it by hanger space of 1.0~1.5m.
3
Install the air vent in the horizontal drainpipe to prevent water flow back to the indoor unit.
Note
4
You may not need to install it if there were proper slope in the horizontal drainpipe.
The flexible hose should not be installed upward position, it may cause water flow back to the
indoor unit.
Air vent
300mm or less
Flexible hose
200mm
or more
1~1.5m
Hanger
20mm
or more
Within
300~550mm
Horizontal drainpipe
more than 1/100 slope
Ceiling
28
Testing the drainage
ENGLISH
Prepare a little water about 5 liter.
1
Pour water into the base pan in the indoor unit as shown in figure.
2
Confirm that the water flows out through the drain hose.
29
Wiring work
A
Power and communication cable connection
1
Before wiring work, you must turn off all power source.
2
Indoor unit power should be supplied through the breaker( ELCB or MCCB+ELB ) separated by the
outdoor power.
ELCB: Earth Leakage Circuit Breaker
MCCB:Molded Case Circuit Breaker
ELB:Earth Leakage Breaker
3
The power cable should be used only copper wires.
4
Connect the power cable{1(L), 2(N)} among the units within maximum length and communication
cable(3(C)) each.
5
Connect V1, V2(for DC12V) and F3, F4(for communication) when installing the wired remote control.
WARNING
Power off before connecting any wires;
Indoor PBA will be damaged while V1,V2,F3,F4 short each other.
Indoor unit
NS012SCRE/RC012FSTRE
NS018SCRE/RC018FSTRE
Wired
Remote
Controller
Main Power
220-240V~, 50Hz
Outdoor unit
 Between Indoor and Outdoor Connection Cord Specifications
Power Supply (Single Phase)
Power Supply
Max/Min(V)
Connection Wire
220-240V~/50Hz
±10%
1.25mm2,2 wires
Earth Cable
Communication Cable
Ø 1.6mm,1 wire
0.75~1.25mm2 ,1 wire
kThe terminal block designs and shape are subject to change according to the model.
k For connection cord, use the grade H07RN-F or H05RN-F materials.
k Screws on terminal block must not be unscrewed with the torque less than 12 kgf•cm.
30
Indoor unit
NS024SCRE/RC024FSTRE
NS036SCRE/RC036FSTRE
ENGLISH
Wired
Remote
Controller
Main Power
220-240V~, 50Hz
Outdoor unit
Indoor unit
NS036SCRE/RC036FSTRG
NS048SCRE/RC048FSTRG
NS060SCRE/RC060FSTRG
Wired
Remote
Controller
Main Power
3N~,380-415V, 50Hz
Outdoor unit
 Between Indoor and Outdoor Connection Cord Specifications
Power Supply (Single Phase)
Power Supply
Max/Min(V)
Connection Wire
220-240V~/50Hz
±10%
1.25mm2,2 wires
Earth Cable
Communication Cable
Ø 1.6mm,1 wire
0.75~1.25mm2 ,1 wire
kThe terminal block designs and shape are subject to change according to the model.
k For connection cord, use the grade H07RN-F or H05RN-F materials.
k Screws on terminal block must not be unscrewed with the torque less than 12 kgf•cm.
31
Wiring work
A
Selecting compressed ring terminal
Silver solder
B
D
d1
E
F
L
d2
t
Norminal Norminal
Standard
Standard
Standard
dimensions dimensions Standard
Allowance
Allowance
Allowance
Allowance
dimension
dimension
Min. Min. Max. dimension
Min.
for cable for screw dimension
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
(mm2)
4
6.6
+0.3
+0.2
1.5
±0.2
3.4
1.7
±0.2
4.1
6
16
4.3
0.7
4
8
-0.2
0
4
6.6
+0.3
+0.2
2.5
±0.2
4.2
2.3
±0.2
6
6 17.5
4.3
0.8
4
8.5
-0.2
0
+0.3
+0.2
4
4
9.5
±0.2
5.6
3.4
±0.2
6
5
20
4.3
0.9
-0.2
0
CAUTION

















Select the power cable in accordance with relevant local and national regulations.
Wire size must comply with local and national code.
For the power cable, use the grade of H07RN-F or H05RN-F materials.
You should connect the power cable into the power cable terminal and fasten it with a clamp.
The unbalanced power must be maintained within 10% of supply rating among whole indoor
units.
If the power is unbalanced greatly, it may shorten the life of the condenser. If the unbalanced
power is exceeded over 10% of supply rating, the indoor unit is protected, stopped and the error
mode indicates.
To protect the product from water and possible shock, you should keep the power cable and the
connection cord of the indoor and outdoor units in the iron pipe.
Connect the power cable to the auxiliary circuit breaker.
An all pole disconnection from the power supply must be incorporated in the fixed wiring(≥3mm).
You must keep the cable in a protection tube.
Keep distances of 50mm or more between power cable and communication cable.
Maximum length of power cables are decided within 10% of power drop. If it exceeds, you must
consider another power supplying method.
The circuit breaker(ELCB or MCCB+ELB) should be considered more capacity if many indoor units
are connected from one breaker.
Use round pressure terminal for connections to the power terminal block.
For wiring, use the designated power cable and connect it firmly, then secure to prevent outside
pressure being exerted on the terminal board.
Use an appropriate screwdriver for tightening the terminal screws. A screwdriver with a small
head will strip the head and make proper tightening impossible.
Over-tightening the terminal screws may break them.
See the table below for tightening torque for the terminal screws.
Tightening torque(kgf•cm)
32
M3
5.9
M4
12.0~14.7
Adjusting
air flow
A
E. S. P(External Static Pressure) setting for phase control motor
Static Pressure(mmAq)
Model
Step
NS012SCRE
MID
HI
LOW
HI
NS018SCRE
MID
LOW
HI
NS024SCRE
MID
LOW
HI
NS036SCRE
MID
LOW
HI
NS048SCRE
MID
LOW
HI
NS060SCRE
MID
LOW
0
2
4
6
8
10
12
14
15
Option code for indoor unit
010044 010044
-1600F3 -16023A
010044
-160380
-
-
-
-
-
-
010001 010001
-1A027F -1A03A2
010001
-1A03D4
010003
-1A0156
-
-
-
-
-
010003 010003
-1C013D -1C014F
010004
-1C0215
010004
-1C03F5
010004
-1C03FD
-
-
-
-
010003 010003
-1F018E -1F01AF
010004
-1F00D0
010004
-1F0232
010004
-1F02F5
010004
-1F02F5
-
-
-
010814- 0108141300B4 1300D6
0108141300F8
01081413021A
01081413023C
010814- 010814- 010814- 01081413025E 1303A0 1303F4 1303F6
010814- 0108141400E1 140204
010814140225
010814140257
010814140299
010814- 010814- 010814- 010814140279 140259 140259 140259
Note  represents E. S. P(External Static Pressure) range of factory setting.
You don’t have to adjust the fan speed separately if the external static pressure of the installation place
. When it is out of , input the appropriate option code.
is in
 If you input the inappropriate option code, error may occur or the air conditioner is out of order. The
option code must be inputted correctly by the installation specialist or service agent.
33
ENGLISH
With its phase control motor, you can adjust the indoor unit fan speed depending on the installation condition.
If the external static pressure is high so that the duct becomes longer or if the external static pressure is low so
that the duct becomes shorter, adjust the fan speed by referring the following table. Refer to the page 34 to set
the option code.
Setting up the mode option
Setting option setup method
For example) Option code :
1
Prepare of the option setup mode.
a. Take out the batteries of remote control.
b. Press the
button simultaneously and insert the battery again.
c. Make sure the remote control display shows as
2
.
Enter the option setup mode and select your option according to the
following procedure.

The default value is
. Otherwise, push the
button to
.



 E very time you press the button, the display panel reads or

repeatedly.

Press the
button to set the display panel to
 E very time you press the button, the display panel reads
  ...      repeatedly.

Press the
button to set the display panel to
Press the
Press the
Press the
button to set the display panel to
 
.
 E very time you press the button, the display panel reads
  ...      repeatedly.
34
 
button to set the display panel to .
 E very time you press the button, the display panel reads
  ...      repeatedly.

 
button to set the display panel to .
 E very time you press the button, the display panel reads
  ...      repeatedly.

 
.
 E very time you press the button, the display panel reads
  ...      repeatedly.



.
 
 Setting is not required if you want to input
. is displayed by default.
Press the
button, then the default value is
.

Press the
button to set the display panel to
.
 E very time you press the button, the display panel reads
  ...      repeatedly.

Press the
button to set the display panel to
ENGLISH

 
.
 E very time you press the button, the display panel reads
  ...      repeatedly.



 


Press the
button to set the display panel to
.
 E very time you press the button, the display panel reads
  ...      repeatedly.
Press the
button to set the display panel to
button to set the display panel to
 
 Setting is not required if you want to input
. is displayed by default.
.
 E very time you press the button, the display panel reads
  ...      repeatedly.
3
 
.
 E very time you press the button, the display panel reads
  ...      repeatedly.
Press the


 
Check you made right selections upon completion of the selection.
a. Press the
button once to check the former part of option code
you inputted.
 T he display part shows
.
b. Press the
button once to check the former part of option code
you inputted.
 T he display part shows
.
35
Setting
up the mode option
A
4
Press the
button.
hen you press the
W
button towards the indoor unit,
the sound ‘Ding’ or ‘Diriring’ is heard and the power indicator of the
display flashes at the same time. Then the option code setting is
completed.
button again.)
(If the sound is not heard, press the
5
Check the air conditioner operates normally.
a. Remove the battery from the remote control.
b. Insert the battery into the remote control again.
c. Press the
towards the indoor unit.
Note If all indicators of the indoor unit are flashing, plug out the
power plug and plug it in again.
button.
Then press the
 If the air conditioner does not operate normally or all lamps
indicators flash, check that the correct option code is set up.
Option items
Remote
control SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 SEG7 SEG8 SEG9 SEG10 SEG11 SEG12
Model
NS012SCRE
0
1
0
0
4
4
1
6
0
2
3
A
NS018SCRE
0
1
0
0
0
1
1
A
0
3
D
4
NS024SCRE
0
1
0
0
0
4
1
C
0
2
1
5
NS036SCRE
0
1
0
0
0
4
1
F
0
2
F
5
NS048SCRE
0
1
0
8
1
4
1
3
0
2
3
C
NS060SCRE
0
1
0
8
1
4
1
4
0
2
9
9
 If you are going to use up to SEG 24, please refer to following instruction.
SEG 17 : 0 1: Using high ceiling kit for 4way.
SEG 18 :
Change temperature display
Sound Mute
Mixed operation control
Not in use
0(Celsius)
0
0
Use
1(Fahrenheit)
2
4
 If you want to use multiple functions, add each of the ‘use’ value of the function you want to used and input the final
addition as option value.(Use Fahrenheit + Sound mute + Mixed operation control : 1 + 2 + 4 = 7)
Ex) 044217-1d00e6-200000-300000
When using Sound mute : 044217-1d00e6-200002-300000
When using high ceiling kit for 4way and mixed operation error preventing function : 044217-1d00e6-200014-300000
36
A
Assigning address to indoor unit
Before installing the indoor unit, assign an address to the indoor unit according to the air conditioning
system plan.
2
The address of the indoor unit is assigned by adjusting MAIN(SW02) and RMC(SW04) rotary switches.
01
78
23
9
ENGLISH
1
 The designs and shape are subject to
change according to the model.
456
Setting Main Address
 The MAIN address is for communication between the indoor unit and the outdoor unit.
Therefore, you must set it to operate the air conditioner properly.
 You can set the MAIN address from ‘0’ to ‘9’ by SW02.
The MAIN address from ‘0 to ‘9’ should differ from each other.
 Check the indoor unit address on the plan that you may install and set the address according to the
plan.
Note
You may not need to set main address if you selected Auto Address Setting from the
outdoor unit: see details on the outdoor unit installation manual.
For Example
When MAIN address is set as "2".
78
456
Setting RMC Address
01
23
9
 The SW04 RMC switch is the address setting switch for controlling the indoor unit with the centralized controller.
 You must set the SW04 and K2 switch when using the centralized controller.
For Example
When RMC address is set as "2".
37
Additional functions
Function
ON
OFF
Model
K1
External room sensor
Not use
Use
12/18/24/36
K2
Centralized controller
Not use
Use
12/18/24/36
/48/60
K3
-
-
-
-
K4
Option drain pump
Not use
Use
12/18/24/36
/48/60
No.
SW05
K1 K2 K3 K4
SW05
 K1 OFF
Heating mode : Setting temperature compensation value = 0°C
Thermo OFF Fan OFF
No.
SW06
Function
Model
K5
+2°C
+5°C
12/18/24/36
/48/60
K6
Filter Time
1000
hours
2000 hours
12/18/24/36
/48/60
K7
Hot Water Heater
Not use
Use
36/48/60
K8
Heater
Not use
Use
36/48/60
Function
ON
OFF
Model
K9
-
-
-
-
K10
Wired Remocon
Group Master
Not use
Use
36/48/60
K11
External control
Not Use
Use
12/18/24/36
/48/60
K12
38
OFF
Heating Current
Temperature
Compensation
No.
SW07
ON
Operation output Thermal ON Operation ON
12/18/24
/36
K5 K6 K7 K8
SW06
K9 K10 K11 K12
SW07
Final check
To complete the installation, perform the following checks and tests
to ensure that the air conditioner operates correctly.
ENGLISH
Check the following:







Strength of the installation site
Tightness of pipe connection to detect gas leak
Electric wiring connection
Heat-resistant insulation of the pipe
Drainage
Grounding conductor connection
Correct operation (follow the steps below)
Providing information for user
After finishing the installation of the air conditioner, you should explain the following to the user.
Refer to appropriate pages in the user & installation manual.
1
How to start and stop the air conditioner
2
How to select the modes and functions
3
How to adjust the temperature and fan speed
4
How to adjust the airflow direction
5
How to set the timers
6
How to clean and replace the filters
Note
W
hen you complete the installation successfully, hand over the user & installation
manual to the user for storage in a handy and safe place.
39
Troubleshooting
A
Detection of errors
 If an error occurs during the operation, an LED flickers and the operation is stopped except the LED.
 If you re-operate the air conditioner, it operates normally at first, then detect an error again.
LED Display on the receiver & display unit
LED Display
Indicators
Concealed Type
Abnormal conditions
Green
Red
Operating
Standard Type
Power reset
Error of temperature sensor in indoor unit
(OPEN/SHORT)
Displayed on
appropriate indoor unit
which is operating
Error of heat exchanger sensor in indoor unit
Error of heat exchanger OUT sensor in indoor unit
Error of outlet temperature sensor in indoor unit
(OPEN/SHORT)
Displayed on
appropriate indoor unit
which is operating
Error of the outdoor temperature sensor
Displayed on
appropriate indoor unit
which is operating
Displayed on outdoor
unit
Error of the condensor temperature sensor
Error of the discharge temperature sensor
1. No communication for 2 minutes between
indoor unit and outdoor unit (communication
error for more than 2 minutes)
2. Indoor unit receiving the communication error
from outdoor unit
3. Outdoor unit tracking 3 minute error
4. When sending the communication error from
outdoor unit the mismatching of the
communication numbers and installed
numbers after completion of tracking.
(communication error for more than 2 minutes)
 On
Flickering
1. Error of indoor unit:
Displayed on the
indoor unit regardless
of operation
2. Error of outdoor unit:
Displayed on the
indoor unit which is
operating
Off
 If you turn off the air conditioner when the LED is flickering, the LED is also turned off.
 If you re-operate the air conditioner, it operates normally at first, then detect an error again.
40
ENGLISH
LED Display
Indicators
Concealed Type
Abnormal conditions
Green
Remarks
Red
Standard Type
Communication error between indoor units
X
1. Error of electronic expansion valve close
2. Error of electronic expansion valve open
3. 2’nd detection of high temperature
cond
4. 2’nd detection of high temperature
discharge
5. Error of reverse phase
6. Compressor down due to 6th detection
of freezing
X
X
Detection of the float switch
X
X
Error of setting option switches for
optional accessories
X
X
EEPROM error
X
X
X
X
X
EEPROM option error
 On
Flickering
Off
 If you turn off the air conditioner when the LED is flickering, the LED is also turned off.
 If you re-operate the air conditioner, it operates normally at first, then detect an error again.
41
Troubleshooting
Wired remote control
If an error occurs,
is displayed on the wired remote control.
If you would like to see an error code, press the Test button.
Display
Explanation
Compressor down due to protection control of the discharge
temperature sensor
Remark
Error about protection
control of the outdoor unit
Control due to the condenser temperature sensor when cooling
mode
Error of the low pressure switch (Protection control)
Reverse phase error (Protection control)
In removing frost
Error of discharge temperature sensor (Open/Short)
Error about the outdoor unit
sensor (Open/Short)
Detection during the
operation of the indoor unit
(sensing and sending errors
into the communication data)
- System down caused by communication error after completion of
tracking
Communication and the
indoor unit errors
Error of the outdoor temperature sensor (Open/Short)
Error of condensor temperature sensor (Open/Short)
- Mismatching of the indoor unit numbers set with those
communication after completion of 5 times tracking
Error of temperature sensor in the indoor unit (Open/Short)
Self-diagnosis of the indoor
and outdoor unit
Error of the heat exchanger sensor in the indoor unit (Open/Short)
Error of electronic expansion valve open in the outdoor unit
(when it is detected more than once)
Error of electronic expansion valve close in the outdoor unit
(when it is detected more than once)
Error of communication between the indoor unit and the wired
remote controller
Master wired remote controller nSlave wired remote controller
COM1/COM2 Cross-installed error
Error of setting option for wired remote controller COM2
42
Wired remote controller
errors
Memo
ENGLISH
43
QUESTIONS OR COMMENTS?
COUNTRY
CALL
OR VISIT US ONLINE AT
IRAN
021-8255 [CE]
021-42132 [HHP]
www.samsung.com/iran/
support
OMAN
800-SAMSUNG (800 - 726 7864)
U.A.E
800-SAMSUNG (800 - 726 7864)
KUWAIT
183-CALL (183-2255)
BAHRAIN
8000-GSAM (8000-4726)
EGYPT
08000-7267864
16580
www.samsung.com/eg/support
JORDAN
0800-22273
06 5777444
www.samsung.com/Levant
MOROCCO
080 100 22 55
www.samsung.com/n_africa/
support
SAUDI ARABIA
800 247 3457 (800 24/7 HELP)
www.samsung.com/sa/home
www.samsung.com/sa_en
TURKEY
444 77 11
www.samsung.com/tr/support
www.samsung.com/ae/
support (English)
www.samsung.com/ae_ar/
support (Arabic)
Duct Type Series
MA duct:
NSSCRE
Air Conditioner
user & installation manual
imagine the possibilities
Thank you for purchasing this Samsung product.
EN FA DB98-33928A-04
Download PDF