Samsung | AW2492L | Samsung AW2492L 사용자 매뉴얼

OWNER'S
INSTRUCTIONS
AW2492L
Window-type Room Air Conditioner
(Cool)
E S DB98-15119A
Safety Precautions
The following safety precautions must be taken when installing
and using your air conditioner.
1 The air conditioner must be plugged into its own specific power source, which must be
installed in compliance with national wiring, earthing and safety regulations.
Depending on national regulations and your specific installation, you may need to install:
A circuit breaker
For further information on electrical requirements, contact a professional electrician.
This device must be installed according to the national electrical rules.
2 Make sure that the unit is correctly ventilated at all times;
do NOT place clothing or other materials over it.
3 NEVER spill liquids of any kind into the unit.
Should this happen, unplug the unit and contact your installation specialist.
4 Do NOT insert anything between the air outlet blades, as it may damage the inner fan
and you may get hurt. Keep children away from the unit.
5 If the supply cord is damaged, it must be replaced by the manufacturer, its service agent
or similarly qualified persons in order to avoid a hazard.
6 Do NOT attempt to repair the unit yourself. If it is damaged in any way, contact:
An authorized service center
The dealer from whom you purchased the air conditioner.
7 Do NOT place any blocking objects in front of the unit.
8 If the remote control will not be used for a long time, remove the batteries.
9 Before throwing out the device, it is necessary to pull back the battery cells
and get rid of them safely.
10 The appliance is not intended for use by young children or infirm person without supervision;
young children should be supervised to ensure that they do not play with the appliance.
11 Do NOT use an extension cord with this product.
CA U T I O N
The manufacturer does not assume responsibility for accidents or injury
caused by an incorrectly installed air conditioner. If you are unsure about
installation, contact an installation specialist.
E-2
Contents
PREPARING YOUR AIR CONDITIONER
Safety Precautions .........................................................................................
Description of Each Component ....................................................................
Remote Control - Buttons and display ............................................................
Getting Started ...............................................................................................
Inserting the Remote Control Batteries ..........................................................
2
4
5
6
7
U S I N G T H E C O N T R O L PA N E L O N T H E U N I T
OPERATING YOUR AIR CONDITIONER
Cooling Your Room ........................................................................................ 9
Ventilating Your Room .................................................................................... 10
Removing Excess Humidity ............................................................................ 11
PROGRAMMING YOUR AIR CONDITIONER
Setting the On Timer ......................................................................................
Setting the Off Timer ......................................................................................
Setting the Sleep Timer ..................................................................................
Selecting Energy Saving mode ......................................................................
12
13
14
15
USING T H E WIRELESS REMOTE CONTROL
OPERATING YOUR AIR CONDITIONER
Cooling Your Room ........................................................................................ 17
Ventilating Your Room .................................................................................... 18
Removing Excess Humidity ............................................................................ 19
PROGRAMMING YOUR AIR CONDITIONER
Setting the On Timer ......................................................................................
Setting the Off Timer ......................................................................................
Setting the Sleep Timer ..................................................................................
Selecting Energy Saving mode ......................................................................
Adjusting the Air Flow Direction Horizontally ..................................................
Adjusting the Air Flow Direction Vertically ......................................................
20
21
22
23
24
24
RECOMMENDATIONS FOR USE
Temperature and Humidity Ranges ................................................................
Cleaning Your Air Conditioner ........................................................................
Solving Common Problems ............................................................................
Technical Specifications .................................................................................
25
26
27
27
E-3
Description of Each Component
The design and shape are subject to
change.
Air outlet
Inner air flow blades
(right/left orientation)
Air inlet (Inside)
Outer air flow blades
(up/down orientation)
Air filter
(The air filter is
located in inside.)
Air inlet (Outside)
Air outlet
Ventilation lever
Mode
Cool/Dr
y/Fan
E.Saver
Temp.
Sleep
Timer
Fan Spee
d
Swing
Power
Power plug (The type of
power plug may differ,
depending on the local
power supply.)
Temperature/Timer
settings
Mode
Mode selection button
(Cool,Fan, Dry)
Cool/Dry/Fan
Energy Saver button
E.Saver
Sleep timer setting button
Temp.
Temperature adjustment
buttons
Swing
Sleep
Fan Speed
Timer setting button
On/Off button
Timer
Fan speed adjustment button
E-4
Power
Remote control sensor
Remote Control - Buttons and display
Remote control
transmission indicator
Operating mode
(
Cool,
Dry,
Mode selection button
(Cool, Fan, Dry)
Fan)
Temperature setting
Sleep mode
Energy Saving mode
Fan speed
Air flow direction
On Timer setting
Off Timer setting
Temperature adjustment
buttons
Sleep timer setting button
Fan speed adjustment
button
Energy Saving button
Timer setting button
Timer Set/Cancel button
Battery discharge indicator
Air flow blade swing button
On/Off button
E-5
Getting Started
You have just purchased a Samsung window-type r oom air conditioner which should be installed
following your installation manual.
Your Owner’s Instructions contain much valuable information on using your air conditioner.
Please take the time to r ead them as they will help you take full advantage of the unit’ s features.
The booklet is organized as follows.
The following figures are shown on pages 4 and 5:
-
Description of Each Component
-
Remote control (buttons & display)
They will help you find the buttons and understand the symbols displayed.
In the manual, you will find a series of step-by-step pr ocedures for each function
available.
The illustrations in the step-by-step procedures use four different symbols:
PRESS
E-6
PUSH
IMPORTANT
NOTE
Inserting the Remote Control Batteries
You must insert or replace the remote control batteries when :
You purchase the air conditioner
The remote control does not work correctly
Use two AAA, LR03 1.5V batteries.
Do not use old batteries or different kinds of batteries together.
Batteries may be completely discharged after 12 months, even
if they have not actually been used.
1
Push the battery cover on the rear of the remote control with your thumb
in the direction of the arrow and remove it.
2
Insert the two batteries, taking care to respect the polarities :
+ on the battery with + on the remote control.
- on the battery with - on the remote control.
3
Close the cover by sliding it back until it clicks into place.
E-7
U s i n g th e
C o nt r ol Pa n e l
on the Uni t
p.
Tem
Mo
de
l/Dr
Coo
y/F
an
ing
Sw
r
Powe
ver
E.Sa
p
Slee
d
Spee
Fan
er
Tim
This chapter indicates how to operate and program
your air conditioner with the control panel on the unit.
E-8
Cooling Your Room
You must select the Cool mode if you wish to lower the temperature
in your room. You can also set the Fan speed.
1
Press the
Result:
(On/Off) button.
The air conditioner starts up in the cool mode.
The unit beeps twice.
Control Panel
Power
The air conditioner is fitted with a protection mechanism to prevent
the unit from being damaged when it is started immediately after
being:
Plugged in
Stopped
It will start up normally after three minutes.
2 If the temperature is not displayed on the control panel:
Press the
button on the unit one or more times until the
temperature is displayed.
Mode
Cool/Dry/Fan
Result:
The unit beeps each time you press the
button.
The air conditioner starts up in the Cool mode.
Mode
Cool/Dry/Fan
You can chang modes at any time.
3 To adjust the temperature, press the
or
buttons on the unit one
or more times until the desired temperature is displayed.
The temperature can be set between 64 Fand 86 F.
Result:
Each time you press the
or
buttons:
- The temperature is adjusted by 1 F and displayed on
the control panel
- The unit beeps
The air conditioner starts cooling, if the room temperature is
higher than the selected temperature.
If the room temperature reaches the set temperature, the air
conditioner stops cooling, but the fan is still operating.
4 To set the fan speed:
Press the
button on the unit one or more times until the
desired the Fan speed(F1, F2 or F3) is displayed.
Low
Fan Speed
Medium
High
5 To control the direction of the air flow, refer to page 24.
E-9
Ventilating Your Room
If the air in your room is stale, you can ventilate the room using the Fan feature.
1
If you wish to discharge stale air, push the ventilation lever on the front of the
unit to the right and open position (
Result:
Mode
Mode
Cool/Dry/
Cool/Dry/F
an
Fan
E.Save
r
E.Save
r
Temp.
Temp.
Sleep
Sleep
Swing
Swing
Timer
Fan Speed
Timer
Power
Fan Speed
Power
).
The air inside the room circulates and stale air is discharged
outside.
Otherwise, push the ventilation lever to the left and closed position (
Result:
Control Panel
2
3
The air simply circulates inside the room.
If necessary, press the
Result:
Power
).
(On/Off) button.
The air conditioner starts up in the mode selected when
the unit was last used.
The unit beeps twice.
If the fan speed(F1, F2 or F3) is not displayed on the control panel:
Press the
button on the unit one or more times until the fan speed
(F1, F2 or F3) is displayed.
Result:
The unit beeps each time you press the
button.
The air conditioner starts up in the Fan mode.
You can change modes at any time.
When the air conditioner is in the Fan mode, the temperature
cannot be set or displayed.
4
To set the fan speed:
Press the
button on the unit one or more times until the
desired fan speed(F1, F2 or F3) is displayed.
Low
Medium
High
5
E-10
To control the direction of the air flow, refer to page 24.
Removing Excess Humidity
If the atmosphere in your room is very humid or damp,you can remove
excess humidity without lowering the room temperature too much.
1 If necessary, press the
Result:
(On/Off) button.
The air conditioner starts up in the Cool mode.
The unit beeps twice.
Control Panel
Power
The air conditioner is fitted with a protection mechanism to
prevent the unit from being damaged when it is started
immediately after being:
Plugged in
Stopped
It will start up normally after three minutes.
2 If the temperature is not displayed on the control panel:
press the
button the unit one or more times until the
temperature is displayed.
Result:
The unit beeps each time you press the
button.
The air conditioner starts up in the cool mode.
You can change modes at any time.
3
To adjust the temperature, press the
or
buttons one or
more times until the required temperature is displayed.
Possible temperatures are between 64 F and 86 F inclusive.
Result:
Each time you press the
or
buttons:
- The temperature is adjusted by 1 F
- The unit beeps
The air conditioner starts removing the excess humidity;
the quantity of air is adjusted automatically.
4 To control the direction of the air flow, refer to page 24.
E-11
Setting the On Timer
Control Panel
Power
The On Timer enables you to switch on the air conditioner automatically after a
given time,You can select the On Timer only when the air conditioner is off.You
can select the On timer when the air conditioner operates in the Cool or Dry mode.
1
Check that the air conditioner has been switched off; if necessary,
press the
(On/Off) button.
2
Set the operating time by pressing the Timer button on the unit one or
more times until the desired time is displayed. The operating time can be
set between 1 and 24 hours.
Result:
Each time you press the Timer buton:
- The time is adjust by 1 hour and displayed on the control
panel
- The unit beeps
The operating time is displayed and decreases automatically to
indicate the remaining time.
The air conditioner starts up in the Cool mode automatically
when the operating time reaches zero.
You can select the fan speed, temperature and Energy saving mode
after setting the On timer and Off timer mode. However, when you
change the mode, the On timer and Off timer mode is cancelled.
To Cancel the On Timer
1 To cancel the timer, press the
Timer
button on the unit one or more times
until "--" is displayed.
2 Press the
E-12
(On/Off) button on the unit.
Setting the Off Timer
The Off Timer enables you to switch off the air conditioner automatically after a
given time. You can select the On timer only when the air conditioner is on. You
can select the Off timer when the air conditioner operates in the Cool or Dry mode.
1 Check that the air conditioner has been switched on; if necessary,
press the
(On/Off) button.
Control Panel
Power
22 Set the operating time by pressing the
Timer button on the unit one or
more times until the desired time is displayed. The operating time can be
set between 1 and 24 hours.
Each time you press the Timer button:
- The time is adjusted by 1 hour and displayed on the control
panel
- The unit beeps
The operating time is displayed and decreases automatically to
indicate the remaining time.
The air conditioner switches off automatically when the
operating time reaches zero.
Result:
You can select the fan speed, temperature and Energy saving mode
after setting the On timer and Off timer mode. However, when you
change the mode, the On timer and Off timer mode is cancelled.
To Cancel the Off Timer
1
To cancel the timer, press the
times until "--" is displayed.
2
Press the
Timer
button on the unit one or more
(On/Off) button on the unit.
E-13
Setting the Sleep Timer
The Sleep Timer can be used when your are cooling your room to switch
the air conditioner off automatically after 8 hours.
If you wish to switch the unit off at a specific time, refer to page 13.
Control Panel
Power
1
Make sure that you have selected the Cool mode.
2
Press the
Result:
Cooling
button on the unit.
Each time you press a button, the unit beeps.
The " " will be displayed.
The remaining time is displayed and decreased by 1 hour
automatically to indicate the remaining time.
The air conditioner will be controlled as illustration below
.
When the temperature has
been increased by 2 F
(after 1 hour), it is maintained
for 7 hours.
To Cancel the Sleep Timer
To cancel the timer, press:
The
Result:
button on the unit.
The unit beeps.
The SLEEP indicator is no longer displayed.
The air conditioner operates in the mode selected last.
If you select the Energy Saving mode in the Sleep Timer mode,
the Sleep Timer will be cancelled and the air conditioner will start
up in the Energy Saving mode.
E-14
Setting Energy Saving Mode
If the wish to save energy when using your air conditioner,
select the energy saving mode.
1
To select the energy saving mode, press the
button on the unit one
or more times until the Energy Saver indicator lights up.
Result:
Control Panel
The fan and compressor cycle on and off together.
The fan will continue to run for a short time after the
compressor cycles off.
If you would like the air conditioner to run in the Dry mode, do not
press the
button. You cannot use the Dry mode in the energy
saving mode.
2
To stop the energy saving mode, press the the
on the unit again.
Result:
button
Control Panel
The fan runs at all times, while the compressor cycles on and off.
If you select the Sleep Timer in the Energy Saving Mode, the Energy
Saving will be cancelled and the air conditioner will start up in the
Sleep Timer mode.
E-15
Using t h e
W ir e l e ss
Re mo t e
Cont rol
This chapter indicates how to operate and program
your air conditioner with the control panel on the unit.
E-E-16
8
Cooling Your Room
You must select the Cool mode if you wish to adjust the:
Cooling temperature
Fan speed when cooling
1
If necessary, press the
Result:
(On/Off) button.
The air conditioner starts up in the Cool mode.
The unit beeps.
The air conditioner is fitted with a protection mechanism to
prevent the unit from being damaged when it is started
immediately after being:
Plugged in
Stopped
lt will start up normally after three minutes.
2 If the
is not displayed at the top of the remote control,
press the
button on the remote control one or more times until it
appears.
Result:
The unit beeps each time you press the
The air conditioner runs in the Cool mode.
button.
You can change modes at any time.
3
To adjust the temperature, press the
buttons one or more times
until the required temperature is displayed.
Possible temperatures are between 64°F and 86°F inclusive.
Result:
4
Each time you press the
buttons:
- The temperature is adjusted by 1°F
- The unit beeps
The air conditioner starts cooling, if the room temperature is
higher than the selected temperature.
If the room temperature reaches the set temperature, the air
conditioner stops cooling, but the fan is still operating.
Select the fan speed by pressing the
until the required setting is displayed:
button one or more times
Low
Medium
High
Result:
5
Each time you press the
button, the unit beeps.
To control the direction of the air flow, refer to page 24.
E-17
Ventilating Your Room
If the air in your room is stale, you can ventilate the room using the Fan feature.
1
If you wish to discharge stale air, push the ventilation lever on the front of the
unit to the right and open position (
Result:
Mode
Mode
Cool/Dry/F
an
Cool/Dry/F
an
E.Save
r
Temp.
E.Save
r
Temp.
Sleep
Sleep
Swing
Swing
Timer
Fan Speed
Power
Timer
Fan Speed
Power
).
The air inside the room circulates and stale air is discharged
outside.
Otherwise, push the ventilation lever to the left and closed position (
Result:
2
3
The air simply circulates inside the room.
If necessary, press the
Result:
).
(On/Off) button.
The air conditioner starts up in the Cool mode.
The unit beeps twice.
If the
is not displayed at the top of the remote control,
press the
button on the remote control one or more times until it
appears.
Result:
The unit beeps each time you press the
The air conditioner runs in the Fan mode.
The temperature is set automatically.
button.
You can change modes at any time.
4
Select the fan speed by pressing the
until the required setting is displayed:
Low
button one or more times
Medium
High
Result:
5
E-18
Each time you press the
button, the unit beeps.
To control the direction of the air flow, refer to page 24.
Removing Excess Humidity
If the atmosphere in your room is very humid or damp, you can remove
excess humidity w ithout low ering the room temperature too much.
1
If necessary, press the
Result:
(On/Off) button.
The air conditioner starts up in the Cool mode.
The unit beeps.
The air conditioner is fitted with a protection mechanism
to prevent the unit from being damaged when it is started
immediately after being:
Plugged in
Stopped
It will start up normally after three minutes.
2
If the
is not displayed at the top of the remote control, press the
button on the remote control one or more times until it appears.
Result:
The unit beeps each time you press the
The air conditioner runs in the Dry mode.
button.
You can change modes at any time.
3
To adjust the temperature, press the
buttons one or more times
until the required temperature is displayed.
Possible temperatures are between 64°F and 86°F inclusive.
Result:
4
Each time you press the
buttons:
- The temperature is adjusted by 1°F
- The unit beeps
The air conditioner starts removing the excess humidity;
the quantity of air is adjusted automatically.
To control the direction of the air flow, refer to page 24.
E-19
Setting the On Timer
The On Timer enables you to switch on the air conditioner automatically after a
given time. You can select the On timer only when the air conditioner is off. You
can select the On timer when the air conditioner operates in the Cool or Dry mode.
1
To set the operating time, press the
button one or more times until
the required time is displayed. Possible time is between 1 hour and
24 hours inclusive.
2
Press the
Result:
(Set/Cancel) button to complete the setting.
The remaining time is displayed.
Blinking of the timer indicator stops.
The air conditioner will switch on automatically when the
counter displayed on the remote control reaches the set time
and disappears the On timer setting.
You can select the temperature, Energy saving mode after setting
the On timer mode.
To Cancel the On Timer
1
Press the
(Set/Cancel) button.
If you want to turn on the air conditioner before the timer reaches
the setting time, press the
(On/Off) button.
E-20
Setting the Off Timer
The Off Timer enables you to switch off the air conditioner automatically after a
given time. You can select the Off timer only when the air conditioner is on. You
can select the On timer when the air conditioner operates in the Cool or Dry mode.
1
To set the operating time, press the
button one or more times until
the required time is displayed. Possible time is between 1 hour and
24 hours inclusive.
2
Press the
(Set/Cancel) button to complete the setting.
Result:
The remaining time is displayed.
Blinking of the timer indicator stops.
The air conditioner will switch off automatically when the
counter displayed on the remote control reaches the set time
and disappears the Off timer setting.
You can select the fan speed, temperature, air flow direction and
Energy saving mode after setting the Off timer mode. However,
when you change the mode, the Off timer mode is canceled.
To Cancel the Off Timer
1
Press the
(Set/Cancel) button.
If you want to turn off the air conditioner before the timer reaches
the setting time, press the
(On/Off) button.
E-21
Setting the Sleep Timer
The Sleep Timer can be used when you are cooling to switch the air
conditioner off automatically after a period of 8 hours.
If you wish to switch the unit off at a specific time, refer to
page 21.
1
Make sure that you have selected the Cool mode.
2
Press the
Result:
Cooling
button on the remote control.
Each time you press a button, the unit beeps.
The
indicator is displayed.
The remaining time is displayed and decreased by 1 hour
automatically to indicate the remaining time.
The air conditioner will be controlled as illustration below.
When the temperature has
been increased by 2¡F
(after 1 hour), it is maintained
for 7 hours.
To Cancel the Sleep Timer
To cancel the timer, press:
The
Result:
button on the remote control.
The unit beeps.
The
indicator is no longer displayed.
The air conditioner operates in the mode selected last.
If you select the Energy Saving mode in the Sleep Timer mode,
the Sleep Timer will be cancelled and the air conditioner will start
up in the Energy Saving mode.
E-22
Selecting Energy Saving Mode
If you wish to save energy when using your air conditioner,
select the energy saving mode.
1
To select the energy saving mode, press the
button on the remote
control one or more times until the Energy Saving indicator lights up.
Result:
The fan and compressor cycle on and off together.
The fan will continue to run for a short time after the
compressor cycles off.
If you would like the air conditioner to run in Dry mode, do not press
the
button. You cannot use the Dry mode in the Energy Saving
mode.
2 To stop the energy saving mode, press the
button on the remote
control again.
Result:
The fan runs at all times, while the compressor cycles on and off.
If you select the Sleep Timer in the Energy Saving mode, the Energy
Saving will be cancelled and the air conditioner will start up in the
Sleep Timer mode.
E-23
Adjusting the Air Flow Direction Horizontally
Depending on the position of the unit in your room, you can adjust
the orientation of the inner air flow blades on the right-hand side of
the unit, thus increasing the efficiency of the air conditioner.
1 Press the swing button on the remote control or unit.
Result:
Mode
The inner blades swing automatically left and right.
Cool/Dry/Fan
Temp.
In the Energy Saving mode, the blades may stop when the
compressor is off. For details on the Energy Saving mode, refer to
page 23.
E.Saver
Swing
Sleep
Fan Speed
Power
Timer
2
To stop the blades moving left and right, press the swing button again.
To stop the blades in a specific position and orient the air flow in
the corresponding direction, simply press the swing button when
the blades are in the desired position.
Adjusting the Air Flow Direction Vertically
The outer air flow blades can be adjusted to control the vertical air
flow direction.
RECOMMENDATION
When...
Adjust the blades to face...
Cooling
Upwards.
Adjust the air flow blades to the desired position, by pushing them upwards or
downwards.
If you orient the air flow blades downwards and the unit operates in the Cool
mode for long periods of time, dew may:
Form on the surface of the blades
Drip from the blades
E-24
Temperature and Humidity Ranges
The following table indicates the temperatur e and humidity ranges
within which the air conditioner can be used.
Mode
Indoor Temperature
Outdoor Temperature
Indoor Humidity
Cooling
70°F to 90°F approx.
70°F to 110°F approx.
80% or less
If the air conditioner is used at...
Then...
Higher temperature
The automatic protection feature may be triggered and the air
conditioner stopped.
Lower temperature
A water leakage or some other malfunction may happen if the
heat exchanger freezes.
Higher humidity levels
Water may condense on and drip from the surface of the unit
if it is used for long periods.
E-25
Cleaning Your Air Conditioner
Be sure to clean the air filter periodically to maintain the air conditioner
in the best condition for a long period of time.
When cleaning the air conditioner, turn it off and pull out the
power plug.
1
Open the front grille by pulling on the tabs of the unit.
The removal of the front grille makes it easier to clean the air
conditioner. After opening the front grille, lift it up as much as possible,
then pull down to release it.
Mode
Cool/Dry/Fan
E.Saver
Temp.
Sleep
Swing
Timer
Fan Speed
Power
2
Grasp the handle on the air filter and lift it slightly and then out to the front.
3
Remove all dust on the air filter with a vacuum cleaner or brush.
4
When you have finished, insert the air filter back into its original position.
5
Wipe the surface of the unit with a neutral detergent
and then wipe it again with dry cloth.
(Be sure not to use benzene, solvent or other chemical products.)
Front grille
Grille groove
Body guide
Mode
Cool/Dry/Fan
E.Saver
Temp.
Sleep
Swing
Timer
Fan Speed
Power
If you...
Will not be using the
air conditioner for a
long period of time
Have not used the air
conditioner for a long
period of time
E-26
Then...
Set the fan going for a few hours to
dry the inside of the air conditioner
thoroughly.
Switch the air conditioner off and
unplug it from the wall socket.
Clean the filter and outer surfaces.
Set the fan going for a few hours to
dry the inside of the air conditioner
thoroughly.
Solving Common Problems
Before contacting an authorized service center, perform the following simple checks.
They may save you the time and expense of an unnecessary call.
Problem
Explanation / Solution
The air conditioner does
not operate at all
Check that the circuit breaker used for the air conditioner has not been
triggered.
Check that the power cable is plugged into a wall socket and the socket is
switched on, if necessary.
Check that the temperature indicator on the unit is lit; if necessary,
press the
(On/Off) button on the remote control or unit.
The air conditioner does not
operate with the remote
control
Check that there are no obstacles between you and the unit.
Replace the remote control batteries if necessary.
Check that you are close enough to the unit (seven metres/yards or less).
No beep is heard when you
press the
(On/Off) button
on the remote control
Check that you are pointing the remote control at the remote control sensor
on the unit.
Replace the remote control batteries if necessary.
The air conditioner does not
cool
Check that the correct operating mode has been selected(Cool).
The room temperature may be too low.
Dust may be blocking the air filter; refer to page 26 for cleaning instructions.
Check that there is no obstacle blocking the air flow into or out of the unit.
The timer is not correctly
triggered
Check that the timer has been programmed correctly;
refer to page 12~14, 20~22.
Odors are permeating the
room during air conditioning
Ventilate the room.
Technical Specifications
Design and specifications are subject to change without notice.
Model
Power Supply
AW2492L
230-208V~, 60Hz
E-27
SAMSUNG ROOM AIR CONDITIONER
LIMITED WARRANTY TO ORIGINAL PURCHASER
This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS AMERICA, INC. (SAMSUNG) and delivered new, in the original carton to the original consumer purchaser, is warranted by SAMSUNG against
manufacturing defects in materials and workmanship for a limited warranty period of:
One (1) Year Parts and Labor, Five (5) Years Parts Warranty for Compressor
This limited warranty begins on the original date of purchase, and is valid only on products purchased and used in the United
States. Warranty repairs must be performed by SAMSUNG's authorized service center. To receive warranty service, the original
dated bill of sale must be presented upon request as proof of purchase to SAMSUNG or SAMSUNG's authorized service center.
SAMSUNG will repair or replace any part found to be defective at no charge, as stipulated herein, with new or reconditioned
parts during the limited warranty period specified above. To request warranty service, the purchaser must contact SAMSUNG
for problem determination and service procedures. SAMSUNG does not warrant uninterrupted or error-free operation of the
product. All replaced parts and products become the property of SAMSUNG and must be returned to SAMSUNG. Replacement
parts and products assume the remaining original warranty, or ninety(90) days,whichever is longer.
In - Home Service: During the warranty labor period, in-home service will be provided subject to availability within the contiguous United States. In-home service is not available in all areas. If during in-home service repair can not be completed, it may be
necessary to remove, repair and return the product. If in-home service is unavailable, SAMSUNG may elect, at our option, to
provide for transportation of our choice to and from a SAMSUNG authorized service center. Otherwise, transportation to and
from the SAMSUNG authorized service center is the responsibility of the purchaser.
This limited warranty covers manufacturing defects in materials and workmanship encountered in normal, noncommercial use of
this product and shall not apply to the following, including, but not limited to: delivery and installation; damage which occurs in
shipment; applications and uses for which this product was not intended; failures or problems which are caused by products or
equipment not supplied by SAMSUNG; accidents, misuse, abuse, neglect, misapplication, fire, water, lightning or other acts of
nature; incorrect electrical line voltage, fluctuations or surges; damage caused by improper or faulty installation; product alteration or modification; improper or unauthorized repair; cosmetic damage or exterior finish; product with altered serial numbers;
failure to follow operating and environmental instructions that are covered and prescribed in the instruction book; customer
adjustments, routine maintenance and cleaning; consumable items such as filters; use of non-SAMSUNG or unauthorized parts,
supplies, accessories or equipment which damage this product or result in service problems.
THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE LISTED AND DESCRIBED ABOVE, AND NO WARRANTIES WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, SHALL APPLY AFTER THE EXPRESS WARRANTY PERIODS STATED ABOVE, AND NO OTHER EXPRESS WARRANTY OR GUARANTY GIVEN BY ANY PERSON, FIRM OR
CORPORATION WITH RESPECT TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG. SAMSUNG SHALL NOT BE
LIABLE FOR LOSS OF REVENUE OR PROFITS, FAILURE TO REALIZE SAVINGS OR OTHER BENEFITS, OR ANY
OTHER SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE
THIS PRODUCT, REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF SAMSUNG
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. NOR SHALL RECOVERY OF ANY KIND AGAINST
SAMSUNG BE GREATER IN AMOUNT THAN THE PURCHASE PRICE OF THE PRODUCT SOLD BY SAMSUNG AND
CAUSING THE ALLEGED DAMAGE. WITHOUT LIMITING THE FOREGOING, PURCHASER ASSUMES ALL RISK AND
LIABILITY FOR LOSS, DAMAGE OR INJURY TO PURCHASER AND PURCHASERS PROPERTY AND TO OTHERS AND
THEIR PROPERTY ARISING OUT OF THE USE, MISUSE OR INABILITY TO USE THIS PRODUCT SOLD BY SAMSUNG
NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF SAMSUNG. THIS LIMITED WARRANTY SHALL NOT EXTEND TO
ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS PRODUCT, IS NONTRANSFERABLE AND STATES YOUR
EXCLUSIVE REMEDY.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and
you may also have other rights which vary from state to state.
To obtain warranty service, please contact SAMSUNG at:
SAMSUNG ELECTRONICS AMERICA, INC. - CONSUMER ELECTRONICS CUSTOMER SERVICE
400 Valley Road, Suite 201 Mount Arlington, NJ 07856
Tel: 973-601-6000, Fax: 973-601-6001
1-800-SAMSUNG (1-800-726-7864)
www.sosimple.com
Download PDF

advertising