LG WF-HX110BW

Add to my manuals
44 Pages

advertisement

LG WF-HX110BW | Manualzz
 @ LG
Life's Good
OWNER’S MANUAL
WASHING MACHINE
Please read this manual carefully before operating
your washing machine and retain it for future reference.
WF-HX110BW / WF-S110S
P/No.:MFL67568723 |
ver.022714.00 www.lg.com
Product Features
) The Turbo Drum DD washing machine does not operate with the lid open.
If the lid is opened during wash, rinse and spin cycles, the machine will stop automatically.
A Please close the door gently. Closing the door in an aggressive manner can cause damage and or
injury.
Smart Drum achieved by DD Motor Technology
e Smart Drum with Drum Washing Type is more hygienic and cleaner washer tub that
protects the fabric and prevents damages.
Normal logic control
® A built-in load sensor automatically detects and measures the laundry load and amicroprocessor
optimizes washing conditions such as ideal water Е
consumption and washing time. START № нее ‘=> WASHING b> POWER
e Advanced technology is built into the Electronic Control ЧР e < OFF
System which ensures the best washing result.
New DD type washing with fabric care
IL >
Fast revolution accelerates Laundry blade Fast revolution of Tub rotates to either
detergent dissolving and revolution to either tub creates the side to balance and
soaks thoroughly into the side in turn to remove current of water. unwind laundry.
clothes. stains in the laundry.
Low Noise Direct Drive System
e The advanced Brushless DC motor rotates the Tub directly without belt and clutch,
thereby reducing the noise of the washer.
e The washing machine adjusts to optimum speed according to the type of clothing in
the load.
. TM
SmartDiagnosis
e |t is the technology to transmit the anomalies to the service center when
there is a problem with the washer. It provides the service that gives faith and Smart
trust to the customers through precise and fast analysis. Diagnosis"
READ THIS MANUAL
Inside you will find many helpful hints on how to use and maintain your washer properly. Just a little
preventive care on your part can save you a great deal of time and money over the life of your
washer. You will find many answers to common problems in the Troubleshooting section. If you
review our chart of Troubleshooting Tips first, you may not need to call for service at all.
Introduction Safety Information 4
Identification of Parts 7
Function Information 8
Before Starting to Wash Preparation Before Washing 9
Use of Water, Dispenser Drawer, Detergent, Bleach and Softener 10
Special Guide for Stain Removal 13
Function of each Button 14
Washing Course Normal Wash 16
Smart Rinse 16
Eco Wash 16
Quick Wash 16
Delicate Wash 16
School Care Wash 18
Duvet Wash 18
Silent Wash 18
Favorite Wash 20
Soak Wash 21
Intensive Rinse 22
Additional Function Tub Clean 23
Course Air Dry 24
Option Washing 25
Time Delay (RESERVATION) Wash 26
Other Useful Functions 27
Installation Placing and Leveling 28
Connecting Water Supply Hose 29
Connecting Drain Hose 32
Care and Maintenance Grounding Method 33
Cleaning and Maintenance 34
Soft Safety Door 36
Troubleshooting Common washing problems 37
Troubleshooting 38
SmartDiagnosis™ 39
Terms of Warranty Terms of Warranty 40
Specification Specification 41
Safety Information
Read carefully and thoroughly through this booklet as it contains important safety information
that will protect the user from unexpected dangers and prevent potential damages to the product.
This booklet is divided into 2 parts : Warning and Caution.
: This is a warning sign specifying user’s applications which might
be dangerous.
: This is a sign specifying ‘Strictly Forbidden’ applications.
>> O>
WARNING : Failure to comply with the instructions under this
CAUTION : Failure to comply with the instructions under this
sign may result in major physical injuries or death.
sign may result in minor physical injuries or
damages to the product.
WATER
HEATER
SAFETY
/N WARNING
* Under certain conditions hydrogen gas may be produced in a water heater that has not been
used for two weeks or more. Hydrogen gas can be explosive under these circumstances.
If the HOT water has not been used for two weeks or more, prevent the possibility of
damage or injury by turning on all Hot water faucets and allowing them to run for several
minutes. Do this before using any electrical appliance which is connected to the HOT
water system. This simple procedure will allow any built-up hydrogen gas to escape. Since
the gas 1s flammable, do not smoke or use an open flame or appliance during this process.
PROPER
INSTALLATION
/N CAUTION
* The base opening must not be obstructed by carpeting when the washing machine 1s installed on a
carpeted floor.
* Install or store where it will not be exposed to temperatures below freezing or exposed to the weather.
If the product is exposed to such conditions, electric shock, fire, break down or
deformation may occur.
» Properly ground washer to conform with all governing codes and ordinances. Follow details in
Installation Instructions.
If not grounded properly, break down and leakage of electricity may occur, which may
cause electric shock.
* Must be positioned so that the plug is accessible.
If the plug is placed between the wall and the machine, it may get damaged, possibly
causing fire or electric shock.
* Make sure the plug 1s completely pushed into the outlet.
Failure to do so may cause electric shock and fire due to overheating,
Safety Information
ELE /N WARNING
LAUNDRY
AREA « Keep the area underneath and around your appliances free of combustible
materials such as lint, paper, rags. chemical, etc.
Operating with such materials around the machine may trigger
explosion or fire.
* The appliance 1s not intended for use by young children or infirm persons
without supervision.
* Young Children should be supervised to ensure that they do not play with
appliance.
There is potential danger that children might drown in the tub.
Q Do not touch the power plug with a wet hand.
It will cause electric shock
Do not put your hand. foot or anything under the washing machine
® while the washing machine is in operation.
There is a rotating mechanism under the machine, so you could be injured.
WHEN USING A CAUTION
THE WASHER
* Use this appliance only for its intended purpose as described in this Owner’s Manual.
* The laundry process can reduce the flame retardancy of fabrics. To avoid such a result,
carefully follow the garment manufacturer’s wash and care instructions.
» To minimize the possibility of electric shock, unplug this appliance from the power
supply or disconnect the washer at the household distribution panel by removing the
fuse or switching off the circuit breaker before attempting any maintenance or cleaning.
\ [019 : Pressing Circuit button to turn off DO NOT
disconnect the appliance from the power supply.
» Make sure that drainage is working properly.
If water is not drained properly, your floor may get flooded. Flooded floors
may induce electricity leakage, further resulting in electric shock or fire.
* If, during spinning, opening the lid does not stop the tub within about 15 seconds,
immediately discontinue operating the machine.
Call for repair. A machine that spins with its door open may cause injuries.
Never reach into washer while it is moving.
Q Wait until the machine has completely stopped before opening the lid.
Even slow rotation can cause injury.
Never attempt to operate this appliance if it 1s damaged, malfunctioning, partially
W disassembled, or has missing or broken parts, including a damaged cord or plug.
Operating with a damaged plug may cause electric shock.
Do not use water hotter than 50°C.
OQ Use of excessively hot water may cause damage to fabrics or cause
leakage of water.
Safety Information
WHEN USING
THE WASHER
/N WARNING
O
O
O
Do not use a plug socket and wiring equipment for more than their rated capacity.
Exceeding the limit may lead to electric shock, fire , break down, and/or
deformation of parts.
Do not mix chlorine bleach with ammonia or acids such as vinegar and/or rust remover.
Mixing different chemicals can produce toxic gases which may cause death.
Do not wash or dry articles that have been cleaned in, washed in, soaked in, or spotted
with combustible or explosive substances (such as wax, oil, paint, gasoline, dry-
cleaning solvents, kerosene, etc). Do not add these substances to the wash water.
Do not use or place these substances around your washer or dryer during operation.
It may ignite or explode.
WHEN NOT
IN USE
/\\ CAUTION
» Turn off water faucets to relieve pressure on hoses and valves and to minimize leakage
if a break or rupture should occur. Check the condition of the fill hoses: they may need
replacement after Syears.
» When the air temperature is high and the water temperature is low, condensation may
occur and thus wet the floor.
» Wipe off dirt or dust on the contacts of the power plug.
Using unclean power plug may cause fire.
* Before discarding a washer, or removing it from service, remove the washer lid to
prevent children from hiding inside.
Children may be trapped and suffocated if the lid is left intact.
O
© © ©
Do not attempt to repair or replace any part of this appliance unless specifically
recommended in this Owner’s Manual, or in published user-repair instructions
that vou understand and have the skills to carry out.
Operating the machine with improperly replaced parts may be a
cause for fire or electric shock.
Do not tamper with controls.
It may lead to electric shock, fire , break down, deformation.
Do not yank the power cord in an attempt to disconnect the power plug.
Securely hold the power plug to unplug the machine.
Failure to observe these instructions may cause electric shock or fire
due to short-circuit .
When you are cleaning the washing machine, do not apply water directly to any
part of the washing machine.
It will cause short circuit and electric shock.
Identification of Parts
Body
* Picture might be different by model.
— Shas
FS — *WATERSUPPLY
> HOSE
E Make sure the water
SOFT SAFETY DOOR Abes nt leaks
TEMPERED GLASS
or *
ME Sr POWER PLUG
POWDER AND LIQUID # If the supply cord is
DETERGENT BOX (3) й damaged, it must be
: replaced by the
BLEACH vs + manufacturer orits
DISPENSER (&) A service agents or
‘ = #7 similarly qualified
FUNCTION i person in order to
SELECTOR ii avoid a hazard,
TUB | JET SPRAY CAP
START/PAUSE ;
BUTTON e “DRAIN HOSE
Use to start or for pump model
stop the washing Check if the drain
machine hose 1s hung up
temporarily. before operating the
washing machine.
DOOR SWITCH
ADJUSTABLE LEGS . *DRAIN HOSE
Use to level the washing
5 for non pum
machine for correct PEER
balance & spin mel
operation. BASE
Accessories
Water supply hoses
Anti-rat cover (option)
Fixing screw for Anti-rat cover
(uN
<
1 Each for COLD and
HOT water
NOTE
% Part can be different according to the model.
Le
Function Information
Our machine provides various washing methods which suits various conditions and types of laundry.
Different types of laundry washing
Normal Wash
Use this Course for everyday washing e.g. sheets, towels, T-shirts. (refer to page 16)
Smart Rinse
Use this Course to get better rising performance. (refer to page 16)
Eco Wash
To save water and detergent for less than 7kg of laundry that is not too dirty. (refer to page 16)
Delicate Wash
Wool clothes (lingerie, wool, etc.) which may be easily damaged can be washed. (refer to page 16)
The fibers of machine washable woolens have been specifically modified to prevent felting when they are machine washed.
Most handknitted garments are not made of machine washable wool and we recommend that you hand wash them
» Before washing your woolens check the care label for the washing instructions.
* When washing woolens use a mild Detergent recommended for washing wool.
* Hand washed woolens may be spun in a washing machine to reduce the time they take to dry.
* To dry woolens lay down them flat on a towel and pat into shape. Dry woolens out of direct sunlight. (The heat and tumble action of a
dryer may cause shrinkage or felting of woolen garments.) Some wool underlays and sheepskin products can be washed in a washing
machine but may cause pump blockages. (Ensure that the whole article is suitable for machine washing and not just the backing
material.) You may wish to handwash these articles and place them in the machine to spin dry.
School Care Wash
Use this Course to wash School Uniform. (refer to page 18)
Duvet Wash
Use for blanket or duvet with (hand wash) sign. (refer to page 18)
Silent Wash
Use this Course to wash quietly at mght. (refer to page 18)
Favorite Wash
This setting allows you to store your Favorite wash conditions in the normal cycle memory. (refer to page 20)
Washing according to the condition of laundry
Quick Wash
Quick Wash can be selected to wash lightly soiled clothes of less than 3.0 kg in a short time. (refer to page 16)
Soak Wash
Soak Wash can be selected to wash heavily soiled laundry by soaking in water for some time to remove dirt and grime. (refer to page 21)
Intensive Rinse
Use Intensive Rinse to remove detergents more effectively. (refer to page 22)
Other washing method
Tub Clean
Use this Course to clean the inside of washing machine especially Inner tub & Outer tub . (refer to page 23)
Time Delay (RESERVATION) Wash
Time Delay(RESERVATION) Wash is used to delay the finishing time of the operation.
The number of hours to be delayed can be set by the user accordingly. (refer to page 26)
Option Wash
When the user needs only Spin, Rinse/Spin, Rinse, Wash/Rinse, Wash, Wash/Rinse/Spin, Soak/Wash/Rinse/Spin (refer to page 25)
Preparation Before Washing
Care Labels
* Look for a care label on your clothes. This will tell you about the fabric content of your garment
and how 1t should be washed.
Sort clothes into loads that can be washed with the same wash cycle, Water Temperature and spin speed.
Sorting
To get the best results, different fabrics need to be washed in different ways,
* SOIL (Heavy, Normal, Light) Separate clothes according to the type and amount of soil.
* COLOR (Whites, Lights, Darks) Separate white fabrics from colored fabrics.
* LINT (Lint producers, Collectors) Separate lint producers and lint collectors.
Lint Producers Terry cloth, Chenille, Towels, Nappies, Diapers
Lint Collectors Synthetics, Corduroy, Permanent Press, Socks
Check before Loading
* Check all pockets to make sure that they are empty. Things such as nails, hairclips, matches,
pens, coins, and keys can damage both your washer and your clothes,
* Mend any torn garments or loose buttons. Tears or holes may become larger during washing, > A
* Remove belts, underwires, etc. to prevent damage to the machine or your clothes. DI
* Pretreat any dirt and stains. SOS
* Make sure the clothes are washable in water. = =
» Check the washing instructions.
* Remove tissue in pockets.
A CAUTION
Do not wash or spin any item labeled or known to be water-proof or water-resistant, even if the product care
label on the item permits machine washing. Failure to follow these instructions could result in severe damage to
your laundry, your washer and/or property damage as a result of abnormal vibration of the washer.
- Examples of water-proof or water-resistant items include certain mattress pads, mattress covers, rain gear, camping
gear, skiing apparel , outdoor gear and similar items.
WIRE
Pretreatment on stains or heavy soil
* Pretreat shirt collars and cuffs with a pre-wash product or liquid Detergent when placing them in the washer.
Before washing treat special stains with bar soaps, liquid Detergent or a paste of water and granular Detergent.
* Use a pretreat soil and stain remover.
Treat stains AS SOON AS POSSIBLE. The longer they are left the harder they are to remove. (For more detail refer to pagel 3)
Loading
A WARNING
Do not wash fabrics containing flammable materials (waxes, cleaning fluids, etc.).
: Fire Hazard
Load Size Never place items in the washer that are
The WATER LEVEL should just cover the clothes. Adjust the load size dampened with gasoline or other flammable fluids.
accordingly. Loosely load clothes no higher than the top row of holes in the No washer can completely remove oil.
washer tub. To add items after washer has started, press Start button and Do not dry anything that has ever had any type of
bmerge additional items. Close the lid and press Start button again to restart CNI ON
SHOMCTE Р 5a + | Doing so can result in death, explosion, or fire.
Light and Large-sized clothing
Clothes like downs and woollens are light weight, large and float easily. Use a nylon net and
wash them in a small amount of water. If the laundry floats during the wash cycle, it may
become damaged. Use dissolved Detergent to prevent the Detergent from clumping.
Long laundry items
Use nylon nets for long, DELICATE items. For laundry with long strings or long length, a net will .
prevent tangling during washing. Fasten zippers, hook, and strings to make sure that these items don't
snag on other clothes.
Nylon net 1s not supplied by LG.
Use of Water, Dispenser Drawer, Detergent, Bleach and Softener
Using Water
Amount of WATER LEVEL
* This machine detects the quantity of laundry automatically, then sets the Water Level
and proper amount of Detergent.
* When you select a wash Course, the Water Level will be shown on the control panel.
* The following table shows the amount of water.
* When the Water Level 1s automatically detected, it may differ depending on the quantity
of laundry even though the same Water Level is indicated on the control panel.
NOTE
[ Minimum water amount |
It depends on laundry load and washer model. Or manually you can pour a certain amount water into tub directly to
some height. That's because if water level reaches to the some height sensed by washer itself, washer automatically
operates. In other words, it 1s needed to pour water to the point when washer starts operating.
Water Temperature
* The machine sets the appropriate temperature automatically according to the wash Course.
* The temperature of the water impacts the effectiveness of all laundry additives and therefore, the cleaning results.
We recommend temperatures of:
- HOT 49~60°C...(120-140°F) White items, diapers, underclothing and heavily soiled, colorfast items.
- WARM 29~40°C...(85-105°F) Most items
- COLD* 18~24°C...(65-75°F) Only very bright colors with light soil.
» When washing in COLD water additional steps may be needed:
- Adjust Detergent amount and pre-dissolve Detergent in WARM water
- Pretreat spots and stains
- Soak heavily soiled items
- Use appropriate bleach
* Temperature below 18°C...(65°F) will not activate laundry additives and may cause lint. residue, poor cleaning, etc.
In addition, Detergent manufactures and care labels define COLD water as 26~29°C.. (80-85°F).
If the temperature of the water in the tub is too cold for your hands, the Detergent will not activate and clean effectively.
NOTE
Ifiron 1s present in the water the clothes may become an all-over yellow or they may be stained with brown or orange
spots or streaks. Iron 1s not always visible. Installation of water softener or an tron filter may be necessary for severe cases.
Using Dispenser Drawer
Using the Dispenser Drawer
The dispenser drawer contains 2 compartments:
» Liquid Fabric Softener
* Liquid or Powder Low-Sudsing, High-Efficiency Detergent
The dispenser automatically dispenses additives at the proper time in the wash cycle.
1. Slowly open the dispenser drawer by pulling the drawer out until it stops.
2. After adding laundry products, slowly close the dispenser drawer. Closing the
drawer too quickly could result in early dispensing of additives.
+ Avoid overfilling or splashing when adding laundry products to the dispenser. Doing
so could result in early dispensing of laundry products.
At the end of the cycle, you may see water in the compartments. This is part of the
normal operation of the washer.
10 NOTE : Do not use bleach in the dispenser drawer.
Using Detergent
Detergent
Follow the Detergent package directions. Using too little Detergent is a common cause of laundry problems.
Use more Detergent if you have hard water, large loads, greasy or oily soils or lower Water Temperature.
Choosing the right Detergent
We recommend the use of domestic Detergent, (powder, liquid or concentrated). Soap flakes or granulated
soap powders should not be used in your washing machine. When washing woolens remember to use
Detergent suitable for washing woolens.
How much Detergent
The correct amount of Detergent will vary depending on the amount of soil in your clothes (Jeans and work
clothes may need more Detergent, while bath towels usually need less.).
For liquid and concentrated Detergents, follow the recommendations of the Detergent manufacturer.
Note: To check you are using the correct amount of Detergent, lift the lid of your machine about half-
way through the wash. There should be a thin layer of foam over the surface of the water. Lots of
foam may look good, but it does not contribute to cleaning your clothes. No foam means not enough
Detergent has been used; soil and lint can settle back on the clothes or the washing machine.
If excess Detergent is used, the rinse will not be as clean and efficient. Also, it could cause
environmental pollution, so use it accordingly.
Adding Detergent
Add measured detergent to the detergent compartment of the dispenser drawer.
Detergent is flushed through the dispenser at the beginning of the wash phase.
Detergent usage may need to be adjusted for water temperature, water hardness. size and soil level of the load.
Avoid using too much detergent in your washer, as it can lead to oversudsing and detergent residue being left on
the clothes.
Note : Using Liquid detergent
- Dilute Liquid detergent with water and pour into the tub, start the cycle.
- Delay wash course is not available if you use liquid detergent.
Using liquid detergent without diluting, or leaving laundry for a long time after pouring
diluted liquid detergent into the tub might cause damage, bleaching or discoloration of cloth,
11
Use of Water, Dispenser Drawer, Detergent, Bleach and Softener
Using Liquid Bleach
* Check clothing care label for special instructions and separate the Bleach dispenser (£b)
laundry to be bleached |
* Dilute liquid chlorine bleach. J
* Measure the recommended amount of liquid bleach carefully /
following instructions on the bottle. ús
* Before starting the washer, pour measured amount of bleach directly С | №
into bleach dispenser. Avoid splashing or overfilling. Powdered
bleach should be mixed with water before pouring,
NOTE
m Never pour undiluted liquid bleach directly onto clothes or into the wash basket.
This may cause change of color or damage the laundry.
m Do not pour powdered bleach into bleach dispenser.
Using Fabric Softener
If desired, pour the recommended amount of liquid
fabric softener into the right-hand compartment.
Use only liquid fabric softener.
Dilute with water to the maximum fill line.
* Do not exceed the maximum fill line.
Overfilling can cause early dispensing of the fabric
softener, which could stain clothes.
NOTE : Do not pour fabric softener directly on the
wash load. It may stan the clothes.
= Do not mix with Detergent or bleach.
= Never pour fabric softener directly on clothes. It may stain them.
= Do not stop the washer during the first spin for timely dispensing.
= Option washing is not designed to be used with fabric softener dispenser.
Scrud(Waxy Build up)
12
Scrud is the name given to the waxy build-up that can occur within any washer when the fabric softener comes into
contact with Detergent. This build-up is not brought about by a fault in the machine.
If scrud is allowed to build-up in the machine it can result in stains on your clothes or an unpleasant smell in
your washer.
If you wish to use fabric softener we recommend
» Using fabric softener sparingly.
* When filling the dispenser, do not splash or overfill.
* Clean dispenser as soon as the cycle is finished.
* Clean your machine regularly. (refer to page 23 or 34)
* Cold water washing increases the chance of this build-up occurring. We recommend a regular WARM or HOT wash
e.g. every 5th wash should be at least a warm one.
« Fabric softener of thinner consistency is less likely to leave residue on the dispenser and contribute to a build-up.
Special Guide for Stain Removal
AWARNING
m Do not use or mix liquid chlorine bleach with other household chemicals such as toilet cleaners, rust removers, acid or
products containing ammonia. These mixtures can produce dangerous fumes which can cause serious injury or death.
m To reduce the risk of fire or serious injury to persons or property, comply with the basic wamings listed below:
* Read and comply with all instructions on stain removal products.
* Keep stain removal products in their original labeled containers and out of children’s reach.
* Thoroughly wash any utensil used.
+ Do not combine stain removal products, especially ammonia and chlorine bleach. Dangerous fumes may result.
* Never wash items which have been previously cleaned in, washed in, soaked in or spotted with gasoline, dry cleaning solvents or
other flammable or explosive substances because they give off vapors that could ignite or explode.
» Never use highly flammable solvents, such as gasoline, inside the home. Vapors can explode on contact with flames or sparks.
For successful stain removal:
+ Remove stains promptly.
Determine the kind of stain, then follow the recommended treatment in the stain
removal chart below.
» To pretreat stains, use a prewash product, liquid Detergent, or a paste made from
granular Detergent and water.
* Use COLD water on unknown stains because HOT water can set stains.
» Check care label instructions for treatments to avoid on specific fabrics.
* Check for colorfastness by testing stain remover on an inside seam.
Follow fabric care
label instructions
* Rinse and wash items after stain removal.
Stain Removal
STAIN TREATMENT
Adhesive tape, chewing gum, Apply ice. Scrape off excess. Place stain face down on paper towels. Saturate with prewash stain remover or
rubber cement nonflammable dy cleaning fluid.
Baby formula, dairy products, egg
Use product containing enzymes to pretreat or soak stains.
alcoholic beverages)
Beverages (coffee, tea, soda, Juice,
Pretreat stain. Wash using COLD water and bleach safe for fabric.
Blood Rinse with COLD water. Rub with bar soap. Or pretreat or soak with product containing enzymes. Wash using
bleach safe for fabric.
Candle wax. ray Scrape off surface wax. Place stain face down between paper towels. Press with warm iron until wax is absorbed.
ARE WEN aan Replace paper towels Te Treat remaining stain with prewash stain remover or nonflammable dry cleaning
fluid. Hand wash to remove solvent. Wash using bleach safe for fabric.
Chocolate Pretreat or soak in WARM water using product contaming enzymes. Wash using bleach safe for fabric,
Callar or cuff soil, cosmetics Pretreat with prewash stain remover or rub with bar soap.
Dye transfer on white fabric Use packaged color remover. Wash using bleach safe for fabric.
Grass
Pretreat or soak in WARM water using product contaming enzymes. Wash using bleach safe for fabric,
Grease, oil, tar (butter, fats, salad
dressing, cooking oils, car grease,
motor oils)
Scrape residue from fabric. Pretreat. Wash using hottest water safe for fabric. For heavy stains and tar, apply,
nonflammable dry cleaning fluid to back of stain. Replace towels under stain frequently, Rinse throughly. Wash
using hottest water safe for fabric.
Some inks may be impossible to remove. Washing may set some inks. Use prewash stain remover, denatured
Ink alcohol or nonflammable dry cleaning fluid.
Wash with chlorine bleach if safe for fabric. Or, soak in oxygen bleach and HOT water before washing. Badly
Mildew, scorch mildewed fabrics may be permanently damaged.
Mud Brush off dry mud. Pretreat or soak with product containing enzymes.
Mustard. fomato Pretreat with prewash stain remover. Wash using bleach safe for fabric.
Nail polish May be impossible to remove. Place stain face down on paper towels. Apply nail polish remover to back of stain,
Repeat, replacing paper towels frequently. Do not use on acetate fabrics.
Paria WATER BASED : Rinse fabric in cool water while stain is wet. Wash. Once paint is dry, it cannot be removed,
am, van OIL BASED AND VARNISH : Use solvent recommended on can label. Rinse throughly before washing,
Rust, brown or yellow For spots, use rust remover safe for fabric. For discoloration of an entire load, use phosphate Detergent and
scoloration
nonchlorine bleach. Do not use chlorine bleach because it may intensify discoloration.
Shoe polish
LIQUID : Pretreat with a paste of granular Detergent and water. PASTE : Scrape residue from fabric.
Pretreat with E stain remover or nonflammable dry cleaning fluid. Rub Detergent into dampened area,
Wash using bleach safe for fabric.
13
Function of each Button
Display laundry progress Display remaining time, reservation time, and alarm for trouble
* Laundry progress is indicated * During operation this indicates time to finish of laundry.
here. ex) indicates remaining time of laundry, rinse, spin
* Process to be done will have dry during operation/pause.
light on. Process in progress * If there 15 a trouble, it blinks with buzzer sound and indicates
will blink and process already the source of trouble. It will work normally after
done will have light off. troubleshooting.
smart Drum™
Time Delay (Reservation)
button Tm
* Use for laundry
reservation. | Hr
* To cancel, turn power 3 Li
off. (refer to page 26)
[
Water wave button Buzzer Button Tub Dry Button Water Level button
(display detergent amount)
* To control water wave. * Pressing the * Use this when you
+ Initially set at “medium” | | button allows want to dry the empty | | * Use to adjust Water Level.
but will not be indicated. | | OFF №» ОМ. tub after a wash. * It can be changed during
operation.
To control Strong wave
power, press Strong
wave. (all course except
Allergy Care, Delicate,
Silent and Tub Clean
can adjust wave.)
* Add detergent as much as
indicated amount next to
Water Level.
* Detergent is based on
condensed detergent.
NOTE
* The standard detected by the sensor changing the algorithm is set by the normal standard. It may not be same to
the washing habit of a specific user. So, it does not matter that the user uses it according to her/his washing habit.
* The steam option cannot be used with all cycles.
* Steam may not be clearly visible during the steam cycles. This 1s normal. Too much steam could damage clothing.
* As supplying water temperature different steam time will be different.
14
Air dry START/PAUSE button|| SmartDiagnosis™ POWER button
Function Display
* To shorten dry time. || * Use to start or pause * Use to turn the power
* Air dry is a stand the washing process. || * It marks the place on or off.
alone process. * After 4 minutes in to put the phone to * Push again я power
* Press for 3 seconds pause status, it will Tee when ||, The power goes off
to select, press power || automatically turn SPREE GCOS, automatically about
button to deselect. off. (refer to page 39) 10 seconds after the
(refer to page 24) wash is finished.
—/
Normal School Care
Smart Rinse Duvet
Eco Wash Silent
Quick Wash Tub Clean
Delicates
Wash, Rinse, Spin button | Child lock function Course button
* To change laundry time, + Use to prevent an accident | | * To select laundry
number of rinse, strength by children operating the course.
of spin dry. machine. * Select course by
* Use safe rinse to more + Press ‘rinse’ button and type of clothes
effectively remove detergent. “spin” button simultaneously! | and level of
* Press START/PAUSE for 3 seconds to select or dirtiness.
button to indicate deselect.
remaining time. (refer to page 27)
* Do not use steam with delicate fabrics such as wool, silk, or easily discolored fabrics.
* For optimal steam cleaning performance, limit laundry loads to 3 kg or less.
* When the steam option is selected for the Normal or Favorite Courses, the water level will not exceed
level '7' in order to maintain optimal performance.
* The control panel may differ according to different models.
15
Washing Course
Washing
Course
Add the
laundry
Add
the Detergent
Normal
Used for normal loads, this mode
automatically selects the most
appropriate conditions and completes
the sequence in one operation. The
built-in sensor detects the size of the
load and the ideal wash power and
wash, rinse and spin times are set
accordingly.
re»
E e
* Water will be supplied.
After supplying, launderin
will be rad” J
Use this Course to increase rinsing
performance. This would include
underwear and baby clothes. If
someone has sensitive skin or skin
trouble, use this Course.
Fe»
Ш ©»
* Select the smart
Rinse Course on the
Control panel.
E ©»
* Add designated amount of detergent
by Water Level and close the door,
Use exclusive neutral detergent or
dry detergent for home.
Eco Wash
Eco course consumes less water and
electricity to wash normal clothes.
Fo»
BE eo»
* Select the Eco Wash
Course on the
Control panel.
Ш ©»
+ Add the appropriate quantity of
Detergent as indicated by the
Water Level. Or follow the
Detergent manufacturer's
instructions
Quick Wash
Use this mode when washing
lightly soiled clothes for a short
time. The highly recommended
laundry amount is under 3.0kg.
Fe»
Ш ©»
* Select the
Quick Wash
Course on the
Control panel.
* Add the appropriate quantity
of Detergent as indicated by
the Water Level.
Or follow the Detergent
manufacturer's instructions
Delicates
Use this Course for washing
delicate fabrics such as lingerie and
woolens. (wash only “water
washable” clothes)
Before washing your woolens
check the care label for the
washing instructions.
(wash only water washable clothes)
re»
Ш eo»
* Select the
Delicates
Course on the
Control panel.
Ш ©»
* Use neutral Detergent
appropriate for the
laundry.
* When washing woolens
use a mild Detergent
recommend for washing
wool.
16
Close the lid
© START/PAUSE
Finish
Caution & Note
Ш o>
* Water will be supplied.
After supplying,
laundering will
be started.
* Tub will rotate more than
once without water (While
Water Level LED blinking) to
recognize Water Level.
* Then the Water Level and the
amount of Detergent to be
used will be shown and water
will be supplied.
* When the wash Course
ends, the buzzer will
ring for 10 seconds
before the Power goes
off automatically.
* IF water is already in the tub, or putting wet laundry into the
tub before starting will increase the Water Level.
* With lightweight bulky loads, Water Level can be set low.
Ш ©»
E >
E >
* During rinse, tub will rotate while water is supplied. "Water
supply - Tub rotation - Drain will be repeated 3 times. Water
supply and drain is executed during rinse and this is a part of
normal operation.
Ш ©»
Pi
E >
—
* Lay out in cool floor or on a hanger
covered by a towel to dry these type of
clothes.
* It might have damped clothes because
spin dry intensity and time are set to short
to prevent damage of clothes. (Spin dry
cannot be changed)
17
Washing Course
Washing
Course
© POWER
Add the
laundry
Add
the Detergent
School Care
Use this Course to wash School
Uniform.
ше»
Ш ©»
* Select the School
Care Course on the
Control panel.
Ш ©»
* Add the appropriate
quantity of Detergent
As indicated by the
Water Level,
Or follow the Detergent
Manufacturer's
instructions.
Use for blanket or bedclothes with
"hand wash y sign.
E Oo
E e
* Select the Duvet
Course on the
Control panel.
>»
* Pour detergent after
dissolve at warm water.
IF detergent is pour into
cold water, it might
cause leftover detergent
in bedclothes.
Use this Course to wash quietly in
Silent especially during late night
and dawn.
Ше»
Ш eo»
* Select the Silent
Course
on the Control
panel
Ш ©»
* Add the appropriate
quantity of Detergent as
indicated by the Water
Level.
Or follow the Detergent
manufacturer's instructions
18
Close the lid © START/PAUSE Finish Caution & Note
pu
E o E > E >
* Cashmere bedclothes, acrylic blanket, mixed
©» = spinning blanket, woolen blanket, infilling
E A E — L | (polyester 100), and bed sheet might be damaged
= = » by floating. Please purchase a separate laundry
net to wash.
* Separate bed clothes to general clothes. It might
cause laundry to askew and results in abnormal
washing.
* Spin dry might take longer to spread out laundry
if bedclothes are lumped to a side.
* Never laundry an electric blanket and a carpet. It
cause damage to a laundry machine and the
laundry.
* Please use laundry net to soak and sink
bedclothes that are easy to be inflated. It might
cause damage on laundry and machine parts if
inflated.
PS Ba » Silent Course takes longer washing time than
E o > E > E о» Normal Course,
* То reduce noise in spinning, spin rpm is
lower than normal spinning rpm.
So the laundry has more moisture than
normal.
19
O POWER
20
Press the POWER button to turn power on.
Put laundry in and Press the Course button to Select Favorite Course.
+ Press Water Wave button and select Water Wave.
("Medium Wave" if nothing 1s selected)
e Select Water Level by pressing Water Level button.
« Select laundry time, number of rinse, and Spin intensity desire to save by
pressing each of laundry, rinse and Spin button.
Press the START/PAUSE button.
Add designated amount of detergent by Water Level and close
the door.
« Please use appropriate exclusive neutral detergent or dry detergent for home when
"Delicate" course 1s selected for Favorite Course.
When the wash Course ends, the buzzer will ring for 10 seconds
before the Power goes off automatically.
= To save Favorite Course.
otc 1. Select laundry options and operate as above.
2. It is saved as the operation starts.
= = 3. It is saved even if laundry 1s paused or power is turned off.
To recall your Favorite cycle.
1. Press POWER on.
2. Select the Favorite cycle by pressing the Course.
3. Press the START/PAUSE button. Then the wash cycle starts.
Press the POWER button to turn power on.
Put laundry in and Press the Course button to Select Washing Course.
« Whitening, Allergy Care, Delicate, Quick Wash, Tub Clean Course do not
suppose soak laundry.
Press soak laundry button.
“Soak laundry” can be selected by pressing button and indicated by light on soak
indicator( )
» Soak selection : 15 p30 p45 p 1:00 p 2:00 № 3:00 p off » 15
Press each of rinse and Spin button to select number of Rinse and Spin.
Add designated amount of detergent by Water Level and close the door.
Press the START/PAUSE button.
« Water will be supplied. After supplying, laundry will be started.
When the wash Course ends, the buzzer will ring for 10 seconds
before the Power goes off automatically.
21
Intensive Rinse
“©
Course
NOTE
Press the POWER button to turn power on.
Put laundry in and Press the Course button to Select Washing Course.
« Intensive Rinse can only be selected only under Normal, Smart Rinse, School Care,
and Favorite.
Press Rinse button to start Intensive Rinse( ).
=]
Leia
1e : is : O mas -
mios = Times — Cms = Les — mes —> aiii
Press each of Wash button and Spin button to set duration.
Add designated amount of detergent by Water Level.
Press the START/PAUSE button.
When the wash Course ends, the buzzer will ring for
10 seconds before the Power goes off automatically.
* Use Intensive Rinse to remove detergents more effectively.
* Intensive Rinse might work if Water Level changed during operation.
Tub Clean
If scrud is allowed to build-up in the machine it can result in stains on your clothes or unpleasant smell in your washer.
Scrud is the way build-up that can occur within any washer when the fabric softener comes into contact with
Detergent, and according to particular degree of dirtiness or quality of water to be use, in these case, use this Course
to clean inner tub and outer tub.
© --
Course
O START/PAUSE
Press the POWER button to turn power on.
Press the Course button to Select Tub Clean Course.
e Water Level of "1" will be selected automatically.
Press the START/PAUSE button.
* Time will be displayed on screen.
After put in exclusive detergent for laundry tub or oxide bleaching
agent in the bleaching agent input and close the door.
When the wash Course ends, the buzzer will ring for 10 seconds
before the Power goes off automatically.
Recommended cleaner :
[= (1) Powder bleaching agent :
pote Purchase a product at a market and refer to usage instruction at the back of the product.
— (2) Liquid bleaching agent:
Dilute to 300 times of water capacity of washing machine.
Do not put laundry for laundry tub course.
« Use oxide bleaching agent (300g). (do not use chlorine bleaching agent.)
« Clean laundry tub per month using laundry tub course.
e Please clean laundry tub if there are fuzz.
e It 1s convenient to use laundry tub course at night or during an outing
23
© POWER Press the POWER button to turn power on.
Press Spin for 3 seconds to select Air Dry.
e Other function cannot be selected during Air Dry.
» Automatically set to 60 minutes upon selection.
n e Press Spin button again to select duration (90min p 120 min № 60 тит.)
(Press E Hold sac. for Ar Dry)
» To deselect Air Dry press power button.
© cams | Press the START/PAUSE button.
When the wash Course ends, the buzzer will ring for
10 seconds before the Power goes off automatically.
€ When you select Air Dry for more than 60 minutes
iil 1) You can reduce the drying time by minimzing the moisture in the laundry.
ps 2) Always keep the laundry amount to 2kg or less and make sure to spread it out evenly.
= 3) Select 60 minutes for cotton laundry and 120 minutes for synthetic fiber laundry for
effective Moisture removal.
Option Washing
When you only need the Wash, Wash/Rinse or Rinse cycles, these can be set manually.
Press the POWER button to turn power on.
O POWER
Only Wash
Only Rinse
Only Spin
Press the Wash button to
select the desired timing.
Press the Rinse button to
select the desired times of
Press the Spin button to
select the desired times of
rinse. 6 spin. e
Wash RINSE sm Spin
Only Wash,Rinse Only Rinse,Spin Only Drain
Press the Wash button to Press the Rinse button to
select the desired timing.
Washes
Press the Rinse button to
select the desired times of
rinse.
Rinses=
You can use this option
select the desired times of
rinse.
RINSE tees
Press the $ in button to
select the desired times of
spin.
Spin
When you want to only
drain, wait until the water
in the washing tub drains
completely.
for preventing wrinkles of
laundry
Press the Water Level button, to control the water
level according to the amount of laundry. If you do
not choose anything, it is set the middle water
level automatically.
Water Level
Add the laundry into the washing tub.
Press the START/PAUSE button.
O START/PAUSE
Add the detergent and close the lid.
NOTE
* When a Wash, Wash/Rinse or Rinse only option 1s selected, after the wash is completed the water will not
be drained off. If you wish to drain the water, press Spin button and wait until the water in the tub has drained
completely. Then press the START/PAUSE button.
* If you do not specify the water level, then Medium will be automatically selected.
* IFonly Rinse is selected, the process will start from Water Supply.
25
Time Delay (RESERVATION) Wash
Course
Time
Delay
© START/PAUSE
Press the POWER button to turn power on.
Put laundry in and detergent and Press the Course button to Select
Washing Course.
* Put detergent in a slot for reserved synthetic powder detergent.
* This Course will not work in Delicate and Tub Clean Course.
Press Time Delay (RESERVATION) button to set reservation time.
« If reservation button is pressed, it will turn on reservation lamp and show up 3:00.
a =
ex) It is 1:00 PM and if you want to finish laundry by 7:00 PM
» Keep press reservation button to set desired laundry ending time.
(7:00-1:00=6hours)
= BEN в г Г Г]
oo Oo uy
J
e Reservation can be made up to 3~18 hours by 1 hour interval up to 3-12hours
and 2 hour interval for 12-18 hours.
+ Less than 3 hour is cannot be reserved.
Close the door and press START/PAUSE button.
* Reservation lamp will blink and remaining time will be displayed
Laundry will be done at reserved time.
» Ending time might be slightly different by water pressure
* If door is opened during reservation.
Press “START/PAUSE” button to reschedule reservation. Then close the door and press
“START/PAUSE” button.
« To cancel reservation, press Time Delay (Reservation) button repeatedly until the reservation
is canceled or press power button to turn off and on power.
Other Useful Functions
Child Lock Function
If you want to lock all the keys to prevent settings from being changed by a child, you can use the
child lock option.
How to Lock
Press the POWER button.
© POWER
Press the START/PAUSE button to start washing.
* After all washing conditions are set according to the manual.
O START/PAUSE
* Turn Power on.
Press both the Rinse button and the Spin button simultaneously.
® (71 * The button lock is set, it will not be released
[Ey automatically if the cycle is terminated.
* Thus, you should turn power on washing machine
and then terminate the function by pushing "Rinse &
Spin" button.
How to Unlock
[If you want to unlock during wash, press both the Rinse and the Spin button simultaneously again,
NOTE
» “| " & the remaining time are alternatively shown on the display while they are locked.
Seeing Remaining Time
To see the remaining time for each process, press one of the Wash, Rinse and Spin buttons.
The remaining time for each process will appear for about 1 second.
27
Placing and Leveling
Please ensure that transit restraint has been removed before operating your machine.
Place the machine on a flat and firm surface which allows proper clearance.
We suggest a minimum clearance of 2 cm to the
right side and left sides of the machine for ease of
more than 10 cm
installation. y =
su more
At the rear, a minimum clearance of 10 em is “ \ >
than =7
suggested. 20m | $
fl more than
| ` 2 ст
МОТЕ
If the washer is installed on a uneven, weak or tilted floor causing excessive vibration,
spin failure or “ Y E ” error can happen to it.
It must be placed on a firm and level floor to prevent spin failure.
Make sure that the washer is properly Level
Open the lid and look from above to see if it is
same as shown.
Top view of the machine
Leveling the machine
Lift the front of the washing machine and twist
the Adjustable Leg until the surface bubble 1s
placed in the center.
Adjustable legs
* Installing the Anti-Rat Cover(option) : Insert the anti rat cover to be firmly fixed from the
back or the front of the washing machine and then secure it by using the setting screw.
If the power is supplied from a extension cord set or generator, the extension cord set or electrical
portable outlet device should be positioned so that it is not exposed to splashing or ingress of moisture.
Connecting Water Supply Hose
Before connecting the Water Supply Hose to the water tap, check the hose type and then choose the
correct instruction here under.
Note that the Water Supply Hose supplied may vary from country to country. Make sure to connect the
blue inlet hose to the COLD water tap, and the orange inlet hose to the HOT water tap.
Connecting Water Supply Hose to water tap
Normal Type (Normal tap without thread & screw type inlet hose.)
Untighten the screw Rubber packing
Untighten the screw of the connector so that the
tap can be placed in the middle. screw
Connector
Fixing the connector to the tap
Push the upper connector up till the rubber
packing is in tight contact with the tap. Then
tighten the 4 screws.
Attach the water supply hose securely to the
connector
Push the water supply hose vertically upwards so
that the rubber seal within the hose can adhere
completely to the tap. Water
Fixing the connector to the water supply hose
Attach the water supply hose to the connector and
then tighten it by screwing it to the right.
After connecting the hose, open the tap to check
for any water leakage.
If the water leaks, close the tap and start again
from step |
NOTE
The washing machine 1s to be connected to the water mains using new hose-sets and old hose-sets should
not be reused.
29
Connecting Water Supply Hose
Normal Type (Normal tap without thread & one touch type inlet hose.)
Separate Middle connector from Water Supply Hose
Separate Middle connector from the Water Middle Fixed Sticker
Supply Hose by pulling the Pressing Rod and the Connector Pressing Handle
Pressing Handle that 1s attached to the Water Pressing Rod
Supply Hose.
Water Supply Hose
Loosen the fixed nuts to connect the connector to the tap
Untighten the screw of the connector so that the
tap can be placed in the middle.
Pressing Rod
screw
Fixed sticker
NOTE
In case tap is too large.
If the tap diameter is too large or is square,
untighten the 4 screws and remove the guide
plate. Then follow stepl.
Fixing Connectors to the Tap
Push the upper connector up till the rubber
packing 1s in tight contact with the tap. Then
tighten the 4 screws.
Fixing Upper Connector and Middle Connector
Remove the fixed sticker in between the Upper
and Middle Connectors. Tighten the connectors Sab Middie Connector
by holding one connector and twist middle 4 Connector > Middle
connector to the right. Fixed sticker Connector
Connector
30
Connecting Middle Connector and Water Supply Hose
Press down the pressing rod of the Water Supply
Hose which was separated from middle connector
(refer to Step!) and then join it to the middle
connector.
Pressing rod МБ Pressing handle
Water Supply Hose
Check for water leakage
After connecting the hose, open the tap to check
for any water leakage.
If the connection leaks, close the tap and start Ss 2
again from step 1. EZ
If you skip step 1, water leakage may occur.
Screw Type
Attach the water supply hose to the tap.
Push the water supply hose up so that the rubber
packing within the hose can adhere completely to
the tap.
>
Rubber Packing
Water Supply Hose
Connect the water supply hose to the tap.
Connect the water supply hose to the tap and then
tighten it by screwing it to the right.
Check water leakage.
After connecting the hose, open the tap to check
for any water leakage.
Connecting Water Supply Hose to the machine
» Connect the water supply hose to inlet valve of
the washing machine, and then lock it by turning
the hose connecting part.
* Check to see 1f there is a rubber seal inside the
connector.
A Te
> i
Fo Fr
A
Л
| Rubber seal
31
Connecting Drain Hose
Before connecting Drain Hose, check your Drain Hose model and choose the correct instructions.
Pump Model
Fit the end of the drain hose to the outlet of the
drain pump and tighten the clamp.
Put the other end of the drain hose over the standpipe or
wash tub.
Drain Hose
NOTE
* To prevent siphoning, the drain hose should not extend more than 50 mm from the end of the hose guide.
* The discharge height should be approximately 0.9 ~ 1.2 m from the floor.
Non-Pump Model
Before connecting
Ensure that the hose clip is set as indicated here.
Connect the Elbow Hose
Push the elbow hose toward the body of the
washing machine,
Place the Drain Hose
To change the direction of the hose, pull out the
elbow hose and change the direction.
Repeat Step 2.
32
Grounding Method
Earth wire should be connected.
If the earth wire is not connected, there is possible a danger of electric shock caused by the current leakage .
Grounding Method with Ground insert space Terminal
~ Ground
[the AC current outlet has a ground terminal, then — Terminal
separate grounding 1s not required. Note that AC power
outlet configurations may differ from country to country
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a dedicated circuit; that 1s, a single outlet circuit which powers
only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's
manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets,
extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these
conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its
appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord
replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular
attention to plugs, wall outlets, and the point where the cord exits the appliance.
Other Grounding Method
Burying Copper Plate
Connect the Ground Wire to a Ground Copper
Plate and bury it more than 75cm in the ground. Ground Wire
E
Using Ground Wire
Connect the ground Wire to the socket provided
exclusively for Grounding,
Using a Short Circuit Breaker
Г Short-circuit
If grounding methods described above are not breaker
possible, a separate circuit breaker should be
employed and installed by a qualified electrician |
* To prevent a possible explosion, do not connect ground to a gas pipe
* Do not connect ground to telephone wires or lightning rods. This may be dangerous during electrical
storms
* Connecting ground to plastic has no effect
* Ground wires should be connected when an extension cord 1s used.
33
Cleaning and Maintenance
Cold water washing
* IF you always use COLD water, we recommend that a WARM or HOT wash be used at a regular
intervals e.g. every Sth wash should be at least a WARM one.
When you have finished
* Turn off taps to prevent the chance of flooding should a hose burst.
* Always unplug the power cord after use.
When water supply into the tub is not clean or the filter is clogged with particles (such as sand), clean the
filter in the inlet valve occasionally.
(The figure of power cord and water tap may vary according to the country)
To Clean the Filter in the Inlet Valve
Close the tap before turning off the power.
HOT/COLD(WARM) and then press the
[START/PAUSE] button to remove water
from the machine completely.
Tum off the power before
pulling out the cord. : e)
m
After removing the water supply
hose pull out the filter.
Then use a brush to clean the filter. —
Replace the filter after cleaning it.
NOTE
* Before cleaning the filter, the impurities in the water supply hose should be removed.
To Clean the Pump casing (for pump model)
Place a towel on the Turn the cap ~~ Remove any foreign ‚ Replace the cap. Insert the filter along
floor under the drain counter- «objects and fluff inside the guide ribs inside the pump casing.
pump cap. Excess clockwise and pump casing and from the Filter must face the guide ribs inside
water may flow out. pull it out. filter. pump casing and securely turn the cap
Filter clockwise.
f= Guide rib
NOTE
* Check 1f water leaks after reassembling. (The Rubber ring is in the cap)
Cleaning and Maintenance
When there is a fear of freezing
* Close the water taps and remove the Water Supply Hose.
* Remove the water which remains in the water supply.
* Lower the drain hose and drain the water in the bowl and the drain hose by spinning.
If frozen
* Remove the water supply hose, and immerse it in HOT water at approx.. 40°C.
* Pour approx.. 2 liters of HOT water at approx.. 40°C, into the bowl and let 1t stand for 10 minutes.
* Connect the water supply hose to the water tap and confirm that the washing machine performs the
supply and drainage of water.
Wash Inner-tub Leave the lid open after washing to allow moisture to evaporate. If you want to clean
the inner-tub use a clean soft cloth dampened with liquid Detergent, then rinse. (Do
not use harsh or gritty cleaners.)
Inlet Hoses Hoses connecting washer to faucet should be replaced every 5 years.
Exterior Immediately wipe off any spills. Wipe with damp cloth. Try not to hit surface with
sharp objects.
Long Vacations Be sure water supply is shut off at faucets. Drain all water from hoses if weather will
be below freezing.
Cleaning the Inside of your Washer
If you use fabric softener or do regular COLD water washing, it 1s very important that you occasionally clean the
inside of your washer.
» Fill your washer with HOT water.
* Add about two cups of a powdered Detergent that contains phosphate.
* Let it operate for several minutes.
« Stop the washer, open the lid and leave it to soak overnight,
» After soaking, drain the washer and run it through a normal cycle.
Or use TUB CLEAN COURSE periodically.
We do not recommend that you wash clothes during this procedure.
Products that might damage your washing machine
* Concentrated bleaches and diaper sanitizer will cause damage to the paintwork and components of your washer.
* Hydrocarbon solvents i.e. petrol, paint thinners and lacquer thinners, etc. can dissolve plastic and blister paint
(Be careful when washing garments stained with these solvents as they are flammable DO NOT put them in
washer or dryer.)
+ Some pretreatment sprays or liquids can damage your washer's control panel.
* Use of dyes in your washer may cause staining of the plastic components. The dye will not damage the machine
but we suggest you thoroughly clean your washer afterwards. We do not recommend the use of dye strippers in
your washer.
* Do not use your washer lid as a work surface.
Soft Safety Door
« Using tempered glass, inside can be seen while washing and safety is guaranteed.
» To prevent sudden close of door, it uses smart hinge so the door closes softly.
* Door 1s heavy. Be careful not to be caught in hand or other material.
[t might cause injury or damage on product.
Smart Hinge
Smart Hinge
NOTE
* For customer safety, the door will be locked automatically during operation (Light turn on "door lock" )sign.
If there are additional laundry to put in, press operate/pause to unlock.
* Press START/PAUSE Button again to resume operation.
36
Common washing problems
Many washing problems involve poor soil & stain removal, residues of lint and scum, and fabric damage.
For satisfactory washing results, follow these instructions.
WASH PROBLEM
Problems Possible Causes Solutions & Preventive Measures
Poor soil * Not enough Detergent + Use correct amount of Detergent for load size, amount of soil and
removal * Wash Water Temperature water Hardness.
too low. * Different Water Temperature may be required according to soil type.
* Overloading the washer * Reduce load size.
* Incorrect wash cycle * Wash with Duvet or Soak & Duvet wash cycle for heavy soiled
* Incorrect sorting laundry
* Dot prevest sell + Separate heavily soiled items from lightly soiled ones.
* Pretreat stain and heavy soil according to directions shown on page 9.
Blue Stains * Undiluted fabric softener * Rub the stain with bar soap. Wash.
dispensed directly onto
fabric
* Do not overfill fabric softener dispenser and do not pour liquid fabric
softener directly onto fabric.
See page 12 for more instructions.
Black or gray
* A buildup caused by the
* Keep the recommendations against Scrud(waxy butldup).
marks on interaction of fabric softener (refer to scrud el2.
clothes and Detergent can flake off г Е o for | fsoil
and mark clothes Use correct amount of Detergent for load size, amount of soil and water
* Not enough Detergent Hardness.
Yellow or * Iron or manganese in * To restore discolored load of whites, use rust remover safe for fabric.
brown rust water supply, water pipes, + Install nonprecipitating water softener or an iron filter in your water
stains or water heater supply system for an ongoing problem.
» Before washing, run water for a few minutes to clear lines.
Lint * Incorrect sorting * Wash lint givers eg towels, flannelette sheets, separately from lint
* Tissues left in pocket collectors eg synthetic fabrics and remove tissues in pockets before wash.
* Overloading the washer See page 9 for sorting and caring before loading.
* Do not overload the washer
Residue or * Overloading the washer * Do not overload the washer,
Detergent * Undissolved Detergent * Some Detergents need to be pre-dissolved, check the Detergent instructions. Try pre-
* Use too much Detergent dissolving the Detergent
* Increase Water Temperature using HOT water safe for fabric.
* Use proper amount of Detergent.
Holes, tears, * Incorrect use of chlorine * Never pour chlorine bleach directly on fabric.
or snags bleach.
* Unfastened zippers,
hooks, buckles
* Ribs, tears and broken
threads
* Overloading the washer
* Degradation of fabric
See page 11 for adding liquid bleach.
* Fasten zippers, hooks, and buckles.
* Remove objects in pockets. See page 9 for caring before
loading.
* Do not overload the washer.
37
Troubleshooting
Before calling for service, check the problem against the list bellows.
Symptom Error Message Check up
* Is the water tap shut off?
» [s the water supply cut off ?
* [5 the tap or water supply hose frozen ?
* Is the water pressure low or is the filter of the inlet valve
clogged with impurities?
* Is the Hot hose connected to cold?
* Is the Cold hose connected to hot?
Water Supply
Failure
* Is the drain hose positioned correctly?
+ Is the drain hose bent or placed too high?
* [s the internal part of the hose or drain pump
(only pump model) clogged with impurities?
* Check if electric power has gone off.
Drainage Failure
® Is the laundry evenly balanced?
SRI Failure » [s the washing machine placed on a flat surface?
Door(Lid) Open
* Is the lid closed?
+ Is the lid closed?
* Make sure that the lid is closed properly and press the
START/PAUSE button.
The washer will not operate unless the lid is locked.
* Make sure that nothing 1s caught under the lid, including shipping
material or clothing.
Door(Lid) Close
* Are there foreign objects such as coins, pins, etc., caught between
the wash plate and the inner basket ?
* Тит off the washer and then press the Power button.
Press the spin speed button without selecting a cycle to drain and
spin the load.
When the spin is complete, remove the clothes and then find and
remove any objects caught in the wash plate.
Foreign objects
The washer
experienced a
power failure.
* Restart the cycle.
* It occurs when there is a failure in the water supply, drainage failure
and the water temperature 1s low.
* Check the water supply and drain cycles are normal?
+ Check the inlet hose, drain hose and the inner tub are freezing?
+ Ifthe test is positive, ask for help to the nearest LG technical assistance.
Avoid freezing at
low temperatures.
) Г » Please call your nearest LG Electronics service center for help.
LL
38
SmartDiagnosis™
Close the washer door, and press the POWER button.
» If you manipulated other button or dial before
pressing Tub Dry button, turn off the power
POWER and start again from the beginning.
Place the phone to SmartDiagnosis™ display.
* Make sure that the
CG speaking side of the e ou
Smart. SmartDiagnosis™
Diagnosis™ display
START/PAUSE
Long press Tub Dry button to activate smart diagnosis.
* Place the phone near the
SmartDiagnosis""
= display, and long press
Tub Dry Tub Dry button
until tak tatk tak sounds.
Note: Before pressing the “Tub Dry” should turn
the power button for reuse if you have made
other operations. If under the condition “CL”,
uninstall it, and reconnect the power.
19) i=
\ = NY, eE
Hold the phone while data is transmitted.
* Keep placing phone to SmartDiagnosis™
display while data for smart diagnosis is being
transmitted. The time remaining for data
transmission will be displayed on screen.
* Transmission sound may be irritating. For
proper diagnosis, do not take off the phone.
You can press power button to stop diagnosis
function and the sound.
After the data transmission is completed, listen to the diagnosis result from the consultant.
* When data transmission is completed, the
EF cd power is automatically turned off with “End”
Ш display after a few seconds.
NOTE
Smart Diagnosis is a troubleshooting feature designed to assist, not replace, the traditional method of
troubleshooting through service calls. The effectiveness of this feature depends upon various factors,
including, but not limited to, the reception of the cellular phone being used for transmission, any
extemal noise that may be present during the transmission, and the acoustics of the room where the
machine is located. Accordingly, LG does not guarantee that Smart Diagnosis would accurately
troubleshoot any given issue.
39
Terms of Warranty
What Is Not Covered:
* Service trips to your home to teach you how to use the product.
* If the product is connected to any voltage other than that shown on the rating plate.
* If the fault is caused by accident, neglect, misuse or Act of God.
* If the fault is caused by factors other than normal domestic use or use in accordance with the
owners manual.
* Provide instruction on use of product or change the set-up of the product.
* [f the fault is caused by pests for example, rats or cockroaches etc..
* Noise or vibration that is considered normal for example water drain sound, spin sound, or
warming beeps.
» Correcting the installation for example, levelling the product, adjustment of drain.
* Normal maintenance which recommended by the owner's manual.
* Removal of foreign objects / substances from the machine, including the pump and inlet hose
filter for example, grit, nails, bra wires, buttons etc.
* Replace fuses in or correct house wiring or correct house plumbing.
* Correction of unauthorized repairs.
» Incidental or consequential damage to personal property caused by possible defects with this
appliance.
* If this product 1s used for commercial purpose, it is not warranted.
(Example : Public places such as public bathroom, lodging house, training center, dormitory)
If the product is installed outside the normal service area, any cost of transportation involved in
the repair of the product, or the replacement of a defective part, shall be borne by the owner.
Model WF-HX110BW WF-S110S
Wash capacity 11.0 kg
Power supply 240 V- 50 Hz 220 V~ 60 Hz
Rated input 600 W
Water tab pressure 30 - 800 kPa (0.3 - 8.0 kgf/cm?)
Weight 45 kg
Size 590(W) x 606(D) x 990(H) mm
% In our continuing effort to improve the quality of our appliances, it may be necessary to make
changes to the appliance without revising this manual.
41
@ LG
Life's Good

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement