Samsung | DVD-P180 | Samsung DVD-P180 User Manual

PRECAUTIONS
1. Setting up
- Refer to the identification label located on
the rear of your player for its proper operating voltage.
- Install your player in a cabinet with adequate ventilation holes. (7~10cm) Do not
block ventilation holes on any of the components for air circulation.
- Do not push the disc tray in by hand.
- Do not stack components.
- Be sure to turn all components off before
moving the player.
- Before connecting other components to this
player, be sure to turn them off.
- Be sure to remove the disc and turn off the
player after use, especially if you don’t use
it for a long time.
- The mains plug is as a disconnect device
and shall stay readily operable at any time.
2. For your safety
- This product utilizes a laser. Use of controls
or adjustments or performance of procedures other than those specified herein may
result in hazardous radiation exposure.
- Do not open covers and do not repair yourself. Refer servicing to qualified personal.
3. Caution
- Your player is not intended for industrial use
but for domestic purposes. Use of this product is for personal use only.
- Apparatus shall not be exposed to dripping
or splashing and no objects filled with liquids, such as vases, shall be placed on the
apparatus.
- Exterior influences such as lightning and
static electricity can affect normal operation
of this player. If this occurs, turn the player
off and on again with the POWER button, or
disconnect and then reconnect the AC
power cord to the AC power outlet. The
player will operate normally.
- When condensation forms inside the player
2
due to sharp changes in temperature, the
player may not operate
correctly. If this occurs, leave the player at
room temperature until the inside of the
player becomes dry and operational.
4. Disc
- Do not clean record-cleaning sprays, benzene, thinner, or other volatile solvents that
may cause damage to the disc surface.
- Do not touch the disc’s signal surface. Hold
by the edges or by one edge and the hole
in the center.
- Wipe the dirt away gently; never wipe a
cloth back and forth over the disc.
5. Environmental info
- The battery used in this product contains
chemicals that are harmful to the environ
ment.
- So, dispose of batteries in the proper man
ner, according to federal, state, and local
regulations.
The product unit accompanying this user manual is
licensed under certain intellectual property rights of
certain third parties. This license is limited to private
non-commercial use by end-user consumers for
licensed contents. No rights are granted for
commercial use. The license does not cover any
product unit other than this product unit and the
license does not extend to any unlicensed product
unit or process conforming to ISO/OUR 11172-3 or
ISO/OUR 13818-3 used or sold in combination with
this product unit. The license only covers the use of
this product unit to encode and/or decode audio files
conforming to the ISO/OUR 11172-3 or ISO/OUR
13818-3. No rights are granted under this license for
product features or functions that do not conform to
the ISO/OUR 11172-3 or ISO/OUR 13818-3.
CAUTION: USE OF ANY CONTROLS,
ADJUSTMENTS, OR PROCEDURES OTHER
THAN SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
Remote Control
Video/Audio
Cable
User’s Manual
Install Batteries in the Remote control
1. Open the battery cover on the back of the remote
control.
2. Insert two AAA batteries.
Make sure that the
polarities (+ and -) are aligned correctly.
3. Replace the battery cover.
If remote control doesn’t operate
properly:
- Check the polarity + - of the batteries (Dry-Cell)
- Check if the batteries are drained.
- Check if remote control sensor is blocked by
TABLE OF
CONTENT
Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Before you start . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Setup
General Features . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Disc Type and Characteristics . . . . . . . . . . . . . . . . 5
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Tour of the Remote Control . . . . . . . . . . . . . . . . . . 8
Connections
Choosing a Connection . . . . . . . . . . . . . . . . . . . . . 9
Basic Functions
Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Using the Search and Skip Functions . . . . . . . . . 13
Using the Display Function . . . . . . . . . . . . . . . . . 13
Using the Disc and Title Menu . . . . . . . . . . . . . . 13
Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Slow Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Advanced Functions
Adjusting the Aspect Ratio (EZ View) . . . . . . . . . 15
Selecting the Audio Language . . . . . . . . . . . . . . . 15
Selecting the Subtitle Language. . . . . . . . . . . . . . 16
Changing the Camera Angle . . . . . . . . . . . . . . . . 16
Using the Bookmark Function . . . . . . . . . . . . . . . 16
Using the Zoom Function . . . . . . . . . . . . . . . . . . . 17
Clips Menu for MP3/WMA/JPEG/
CD Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Folder Selection . . . . . . . . . . . . . . . . . . . . . . . . . . 17
MP3/WMA/CD Audio Playback. . . . . . . . . . . . . . . 17
Picture CD Playback. . . . . . . . . . . . . . . . . . . . . . . 18
Changing Setup Menu
Using the Setup Menu . . . . . . . . . . . . . . . . . . . . . 19
Setting Up the Language Features . . . . . . . . . . . 20
Setting Up the Audio Options . . . . . . . . . . . . . . . . 21
Setting Up the Display Options . . . . . . . . . . . . . . 21
Setting Up the Parental Control . . . . . . . . . . . . . . 22
Reference
Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . 24
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
obstacles.
- Check if there is any fluorescent lighting nearby.
3
English
BEFORE YOU
STAR T
SETUP
General Features
Excellent Sound
Dolby Digital, a technology developed by Dolby
Laboratories, provides crystal clear sound reproduction.
Screen
Both regular and widescreen(16:9) pictures can be
viewed.
Slow Motion
An important scene can be viewed in slow motion.
Parental Control (DVD)
The parental control allows users to set the level
necessary to prohibit children from viewing harmful
movies such as those with violence, adult subject
matter, etc.
Various On-Screen Menu Functions
You can select various languages (Audio/Subtitle)
and screen angles while enjoying movies.
EZ VIEW (DVD)
Easy View enables picture adjustment to match
your TV's screen size (16:9 or 4:3).
Digital Photo Viewer (JPEG)
You can view Digital Photos on your TV.
Repeat
You can repeat a song or movie simply by pressing
the REPEAT button.
MP3/WMA
This unit can play discs created from MP3/WMA
files.
4
Note
- Discs which cannot be played with this
player.
• DVD-ROM
• DVD-RAM
• CD-ROM
• CDV
• CDI
• CVD
• CDGs play audio only, not graphics.
- Ability to play back may depend on recording
conditions.
• DVD-R, +R
• CD-RW
• DVD+RW, -RW (V mode)
- The unit may not play certain CD-R, CD-RW
and DVD-R due to the disc type or recording
conditions.
COPY PROTECTION
Many DVD discs are encoded with copy protection.
Because of this, you should only connect your DVD
player directly to your TV, not to a VCR. Connecting
to a VCR results in a distorted picture from copyprotected DVD discs.
This product incorporates copyright protection
technology that is protected by methods claims of
certain U.S. patents and other intellectual property
rights owned by Macrovision Corporation and other
rights owners. Use of this copyright protection technology must be auzthorized by Macrovision
Corporation, and is intended for home and other
limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
Disc Type and Characteristics
Disc Types (Logos)
Recording Types
DVD
Audio
+
Video
VIDEO-CD
Audio
+
Video
AUDIO-CD
Disc Size
Max. Playing Time
Characteristics
12 Cm
Single-sided 240 min.
Double-sided 480 min.
8 Cm
Single-sided 80 min.
Double-sided 160 min.
- DVD contains excellent sound
and video due to Dolby Digital
and MPEG-2 system.
- Various screen and audio functions can be easily selected
through the on-screen menu.
12 Cm
74 min.
8 Cm
20 min.
12 Cm
74 min.
8 Cm
20 min.
Audio
Disc Markings
~
PAL
Play Region Number
PAL broadcast system in
U.K, France, Germany, etc.
Dolby Digital disc
STEREO
DIGITAL
SOUND
Stereo disc
- Video with CD sound, VHS quality & MPEG-1 compression technology.
- CD is recorded as a Digital
Signal with better audio quality,
less distortion and less deterioration of audio quality over time.
Region Number
Both the DVD player and the discs are coded
by region. These regional codes must match in
order for the disc to play. If the codes do not
match, the disc will not play.
The Region Number for this player is
described on the rear panel of the player.
Digital Audio disc
DTS disc
MP3 disc
You must only insert one DVD disc at a
time. Inserting two or more discs will not
allow to play them back and it may cause
damage to the DVD player.
5
English
This DVD player is capable of playing the following types of discs with the corresponding logos:
Description
Front Panel Controls
1
1.
2.
3.
6
2
4
3
STANDBY/ON ( )
When STANDBY/ON is pressed on, the indicator
goes out and the player is turned on.
STANDBY indicator
When the unit is first plugged in, this indicator
lights.
DISC TRAY
Place the disc here.
5
4.
REMOTE CENSOR
5.
OPEN/CLOSE /STOP ( )
Stops disc play.
Press to open and close the disc tray.
PLAY/PAUSE (
)
Begin or pause disc play.
6.
6
Rear Panel
English
3
1
2
1.
AUDIO OUT JACKS
- Connect to the Audio input jacks of your television or
audio/video receiver.
2.
VIDEO OUT JACK
- Use a video cable to connect to the Video input jack
on your television.
3.
DIGITAL AUDIO OUT JACKS
- Use either coaxial digital cable to connect to a compatible Dolby Digital receiver.
- Use either coaxial digital cable to connect to an A/V
Amplifier that contains a Dolby Digital, MPEG2 or
DTS decoder.
Note
- See pages 21-22 to get more information on how to use the setup menu.
7
Tour of the Remote Control
1
16
17
6.
SEARCH Buttons (
)
/
Allow you to search forward/backward through a disc.
7.
VIDEO SEL.Button
(Only for DVD-P181/DVD-P181K)
8.
SKIP Buttons (
)
/
Use to skip the title, chapter or track.
STOP Button (
)
9.
10. MENU Button
Brings up the DVD player’s menu.
2
3
18
4
5
6
7
8
9
10
19
20
21
22
23
œ/ƒ,¦/‹ Buttons
11. ENTER/œ
This button functions as a toggle switch.
12. EZ VIEW Button
The aspect ratio of a picture can easily be adjusted
according to the screen size of your TV (16:9 or 4:3)
13. DISC MENU Button
Brings up the Disc menu.
14. OPEN/CLOSE (
) Button
To open and close the disc tray
15. AUDIO Button
Use this button to access various audio functions on a disc.
11
12
24
13
25
14
15
26
27
16. DVD Button
Use to operate DVD
17. TV Button
Use to operate TV.
18. BOOKMARK (Number 9 Button)
Quickly find bookmark sections of a DVD
19. STEP /TV SOURCE Button
Advances play one frame at a time.
20. TV CH Buttons
Use to change channel.
21. SUBTITLE Button
1.
DVD Power Button
Turns the power on or standby.
2.
NUMBER Buttons
3.
TITLE MENU (number 7) Button
Brings up the Title menu.
4.
5.
8
ZOOM/- /-- Button
Enlarge DVD Picture
Use this button to select the channel of TV program by inserted the channel number (TV mode).
TV VOLUME
TV VOL(+,-) button
22. PLAY/PAUSE Button (
Begin/Pause disc play.
23. RETURN Button
Returns to a previous menu.
)
24. INFO Button
Displays the current disc mode.
25. CANCEL Button
Use to remove menus or status displays from the
screen.
26. REPEAT A-B Button
Allows you to repeat A-B disc.
27. REPEAT Button
Allows you to repeat play a title, chapter, track, or disc.
CONNECTIONS
The following shows examples of connections commonly used to connect the DVD player with a TV and
other components.
Before Connecting the DVD Player
- Always turn off the DVD player, TV, and other components before you connect or disconnect any cables.
- Refer to the user’s manual of the additional components you are connecting for more information on those
particular components.
Connection to a TV (For Video)
1
Using video/audio cable, connect the VIDEO
(yellow)/Audio (red and white) terminals on the rear of the
DVD player to the VIDEO (yellow)/Audio (red and white)
IN terminals of TV.
WHITE
RED
2
Turn on the DVD player and TV.
YELLOW
Video Cable
Audio Cable
RED
WHITE
YELLOW
3
Press the TV/VIDEO button on the TV's remote
control to select Video.
Note
- Noise may be generated if the audio cable is too close to the power cable.
- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 10 to 11)
- The number and position of terminals can vary depending on your TV set. Please refer to the user's manual of the TV.
9
English
Choosing a Connection
Connection to an Audio System (2 Channel Amplifier)
1
Using the audio cables, connect the AUDIO (red and
white) OUT on the rear of the DVD player to the AUDIO
(red and white) IN terminals of the Amplifier.
2
Using the video signal cable, connect the VIDEO terminals
on the rear of the DVD player to the VIDEO terminal of your
TV.
WHITE
RED
3
Audio Cable
Turn on the DVD player, TV, and Amplifier.
RED
WHITE
4
Press the input select button of the Amplifier to select external input in order to hear sound from the DVD player.
Note
- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause
damage to the speakers and your ears.
- Please set the audio in the menu screen according to the Amplifier. (See pages 21)
- The position of terminals can vary depending on the Amplifier.
Please refer to the user's manual of the Amplifier.
10
Connection to an Audio System (Dolby digital, MPEG2 or DTS Amplifier)
1
English
If using a coaxial cable (not included), connect the DIGITAL AUDIO OUT (COAXIAL) terminal on the rear of the
DVD player to the DIGITAL AUDIO IN (COAXIAL) terminal of the Amplifier.
2
Using the video signal cable, connect the VIDEO terminals
on the rear of the DVD player to the VIDEO terminal of TV.
Coaxial cable
(not supplied)
3
Turn on the DVD player, TV, and Amplifier.
4
Press the input select button of the Amplifier to select
external input in order to hear sound from the DVD player.
Note
- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause
damage to the speakers and your ears.
- Please set the audio in the menu screen according to the Amplifier. (See pages 21)
- The position of terminals can vary depending on the Amplifier.
Please refer to the user's manual of the Amplifier.
11
BASIC FUNCTIONS
Playing a Disc
Before Play
- Turn on your TV and set it to the correct Video
Input by pressing TV/VIDEO button on the TV
remote control.
- If you connected an external Audio System, turn
on your Audio System and set it to the correct
Audio Input.
After plugging in the player, the first time you press the DVD
POWER button, this screen comes up: If you want to select
a language, press a NUMBER button. (This screen will only
appear when you plug in the player for the first time.)
If the language for the startup screen is not set, the settings
may change whenever you turn the power on or off.
Therefore, make sure that you select the language you want
to use.
Once you select a menu language, you can change it by
pressing the
button on the front panel of the unit for
more than 5 seconds with no disc in the unit. Then the
SELECT MENU LANGUAGE window appears again where
you can reset your preferred language.
4. Stopping Play
Press the STOP ( ) button during play.
5. Removing Disc
Press the OPEN/CLOSE ( ) button.
6. Pausing Play
Press the PLAY/PAUSE ( ) or STEP button on the
remote control during play.
- Screen stops, no sound.
To resume, press the PLAY/PAUSE ( )
button once again.
7. Step Motion Play (Except CD)
Press the STEP button on the remote control during play.
- Each time the button is pressed, a new frame will
appear.
- No sound is heard during STEP mode.
- Press the PLAY/PAUSE ( ) button to resume
normal play.
- You can only perform step motion play in the
forward direction.
8. Slow Motion Play
Press SEARCH ( ) button to choose
the play speed between 1/2, 1/4, 1/8 and 1/16 of normal
during PAUSE mode.
- No sound is heard during slow mode.
- Press the PLAY/PAUSE ( ) button to resume
normal play.
- Reverse slow motion play will not work.
Playback
1. Press the OPEN/CLOSE ( ) button. The STANDBY
indicator light goes out and the tray opens.
2. Place a disc gently into the tray with the disc’s label facing
up.
- You must only insert one DVD disc at a time.
Inserting two or more discs will not allow to play
them back and it may cause damage to the DVD
player.
3. Press the PLAY/PAUSE ( ) button or OPEN/ CLOSE
( ) button to close the disc tray.
- When you stop disc play, the player remembers
where you stopped, so when you press
PLAY/PAUSE ( ) button again, it will pick up where
you left off. (unless the disc is removed or the player
is unplugged, or if you press the STOP ( ) button
twice.)
12
Note
- If the player is left in the stop mode for more
than one minute without any user interaction, a
screen saver will be activated. Press the
PLAY/PAUSE ( ) button to resume normal play.
- If the player is left in the stop mode for more than
about 30 minutes, the power will automatically
shut off. (Automatic Power-Off Function)
- If the player is left for about 5 minutes in pause
mode, it will stop.
- This (
) icon indicates an invalid button press.
Note
To access the desired title when there is
more than one in the disc. For example, if
there is more than one movie on a DVD,
each movie will be identified.
During play, you can search quickly through a chapter or track, and use the skip function to jump to the
next selection.
Most DVD discs are recorded in chapters so
that you can quickly find a specific passage
Searching through a Chapter or
Track.
During play, press the SEARCH (
the remote control.
DVD
2X, 4X, 64X, 128X
VCD
4X, 8X
CD
2X, 4X, 8X
or
Allows playback of the film from a desired
time. You must enter the starting time as a
reference.The time search function does not
operate on some disc.
) button on
Refers to the language of the film soundtrack.
In the example, the soundtrack is played in
English 5.1CH. A DVD disc can have up to
eight different soundtracks.
Note
- The speed marked in this function may be different from
the actual speed of playback.
- No sound is hearing during search mode (Except CD).
Refers to the subtitle languages available in
the disc. You will be able to choose the
subtitle languages or, if you prefer, turn them
off from the screen. A DVD disc can have up
to 32 different subtitles.
To access the desired Bookmark or Angle
function.
Some DVD discs are have more angle function from any picture.
Bookmark function make you easily and
quickly to find a track or chapter from DVD.
Skipping Tracks
During play, press the SKIP (
or
) button.
- When playing a DVD, if you press the SKIP (
) button, it
moves to the next chapter. If you press the SKIP (
)
button, it moves to the beginning of the chapter. One more
press makes it move to the beginning of the previous
chapter.
- When playing a CD, in Menu Off mode, if you press the
SKIP (
) button, it moves to the next track. If you
press the SKIP (
) button, it moves to the beginning of
Using the Disc and Title
Menu
Using the Disc Menu
1. Press the MENU button on the remote control.
the track. One more press makes it move to the begin
ning of the previous track.
2. Press the œ/ƒ buttons to select Disc Menu, then press the
‹ or ENTER button.
Using the Display Function
.. Language Setup Page ..
Player Menu ENG
Disc Menu
ENG
Audio
ORI
Subtitle
AUTO
When Playing a DVD/VCD
1. During play, press the INFO button on the remote control.
2. Press the œ/ƒbuttons to select the desired item.
3. Press the ¦/‹ buttons to make the desired setup and then
press the ENTER button.
- You may use the number buttons of the remote control
to directly access a title, chapter or to start the
playback from the desired time.
Note
- Depending on a disc, the Disc Menu may not work.
- You can also use the Disc Menu, using the DISC
MENU button on the remote control.
4. To make the screen disappear, press the RETURN button
again.
13
English
Using the Search and Skip
Functions
Repeat Play
Press the REPEAT button to change playback
mode.
When playing a DVD/VCD
- DVD repeat play by chapter,title,disc
repeat play by disc or track.
- Chapter : repeats the chapter that is playing.
- Title : repeats the title that is playing.
- Disc : repeats the disc that is playing.
- Track : repeats the track that is playing.
- Off
Not
- A-B REPEAT allows you to set point(B) directly
after point (A) has been set.
- Depending on a disc, the Repeat function may
not work.
Slow Play
T
This feature allows you slowly to repeat scenes containing sports, dancing, musical instruments being
played etc., so you can study them more closely.
-
When playing a DVD
1. During play, press the PLAY/PAUSE (
) button.
2. Press the SEARCH ( ) button repeatedly to choose
the play speed between 1/2, 1/4,1/8,1/16 of normal during
PAUSE mode.
Using the A-B Repeat function
1. Press the REPEAT A-B button on the remocon at the point
where you want repeat play to start (A).
2. Press the REPEAT A-B button on the remocon at the
point where you want the repeat play to stop (B).
3. To return to normal play, press REPEAT A-B button
again.
DVD/VCD
14
-
If you are using a 4:3 TV
Adjusting the Aspect Ratio
(EZ View)
-
To play back using aspect ratio
(DVD)
Press the EZ VIEW button.
- The screen size changes when the button is pressed
repeatedly.
- The screen zoom mode operates differently depending on the
screen setting in the Display Setup menu.
- To ensure correct operation of the EZ VIEW button, you
should set the correct aspect ratio in the Display Setup
menu. (See pages 21 to 22).
If you are using a 16:9 TV
For 16:9 aspect ratio discs
- WIDE SCREEN
Displays the content of the DVD title in 16:9 aspect ratio.
- SCREEN FIT
The top and bottom portions of the screen are cut off.
When playing a 2.35:1 aspect ratio disc, the black bars at
the top and bottom of the screen will disappear. The picture
will look vertically stretched. (Depending on a type of disc,
the black bars may not disappear completely.)
- ZOOM FIT
The top, bottom, left and right of the screen are cut off and
the central portion of the screen is enlarge
For 4:3 aspect ratio discs
- Normal Wide
Displays the content of the DVD title in 16:9 aspect ratio.
The picture will look horizontally stretched.
- SCREEN FIT
The top and bottom portions of the screen are cut off and
the full screen appears.
The picture will look vertically stretched.
- ZOOM FIT
The top, bottom, left and right portions of the screen are
cut off and the central portion of the screen is enlarged.
- Vertical Fit
When a 4:3 DVD is viewed on a 16:9 TV, black bars will
appear at the left and right of the screen in order to prevent
the picture from looking horizontally stretched.
For 16:9 aspect ratio discs
- 4:3 Letter Box
Displays the content of the DVD title in 16:9 aspect ratio. The
black bars will appear at the top and bottom of the screen.
- 4:3 Pan&Scan
The left and right portions of the screen are cut off and the
central portion of the 16:9 screen is displayed.
- SCREEN FIT
The top and bottom portions of the screen are cut off and a
full screen appears. The picture will look vertically stretched.
- ZOOM FIT
The top, bottom, left and right of the screen are cut off and
the central portion of the screen is enlarged.
For 4:3 aspect ratio discs
- Normal Screen
Displays the content of the DVD title in 4:3 aspect ratio.
- SCREEN FIT
The top and bottom portions of the screen are cut off and the
full screen appears. The picture will look vertically stretched.
- ZOOM FIT
The top, bottom, left and right portions of the screen are cut
off and the central portion of the screen is enlarged.
Note
This function may behave differently depending on
the type of disc.
Selecting the Audio
Language
You can select a desired audio language quickly and
easily with the AUDIO button.
Using the AUDIO button
1. Press the Audio button. The Audio changes when the audio
button is press repeatedly.
The audio languages are represented by
abbreviations.
DVD
2. To remove the AUDIO icon, press the CANCEL or RETURN button.
15
English
ADVANCED
FUNCTIONS
Note
- This function depends on audio languages are
encoded on the disc and may not work.
- A DVD disc can contain up to 8 audio languages.
- To have the same audio language come up
whenever you play a DVD;
Refer to “Using the Audio Language” on page
20.
Selecting the Subtitle
Language
You can select a desired subtitle quickly and easily
with the SUBTITLE button.
Using the SUBTITLE button (DVD)
Using the Bookmark
Function
This feature lets you bookmark sections of a DVD
so you can quickly find them at a later time.
Using the Bookmark Function
(DVD)
1. During play, press the Bookmark button on the remote
control.
DVD
1. Press the SUBTITLE button. The subtitle languages are
represented by abbreviations. The subtitle changes when
the button is pressed repeatedly.
DVD
Bookmark
Clear
Play
2. When you reach the scene you want to mark, press the
ENTER button. Up to12 scenes may be marked at a time.
English
Bookmark
1
TT:01 CH:05 Time 0:39:23
Clear
Play
Note
- You have to change the desired subtitle in the
Disc Menu, according to discs. Press the INFO
MENU button.
- This function depends on what subtitles are
encoded on the disc and may not work on all
DVDs.
- A DVD disc can contain up to 32 subtitle
languages.
- To have the same subtitle language come up
whenever you play a DVD; Refer to “Using the
Subtitle Language” on page 20.
Note
- Depending on a disc, the Bookmark function
may not work.
Recalling a Marked Scene
1. During play, press the bookmark button on the remocon
2. Press the œ/ƒ¦/‹ buttons to select a marked scene.
Bookmark
1
2
TT:01 CH:05 Time 0:39:23
Clear
Play
Changing the Camera
Angle
When a DVD contains multiple angles of a particular
scene, you can use the ANGLE function.
Using the ANGLE Function (DVD).
If the disc contains multiple angles, the ANGLE
appears on the screen.
3. Press the PLAY/PAUSE (
scene.
) button to skip to the marked
Clearing a Bookmark
1. During play, press the Bookmark button on the remocon.
2. Press the œ/ƒ¦/‹ buttons to select the bookmark number you want to delete.
3. Press the CANCEL button to delete a bookmark number.
1. During play, press the INFO button on the remote control.
2. Press the œ/ƒ buttons to select
3. Press the ¦/‹ buttons or you can use the number buttons
on the remote control to select the desired angel Angle.
16
Bookmark
1
2
3
TT:01 CH:05 Time 0:39:23
Play
Clear
Using the Zoom Function (DVD)
- During DVD play or pause mode, press ZOOM
button on the remocontrol repetedly to zoom in
2X/3X/4X
-
: STOP file icon.
-
: PLAY file icon
-
: WMA file icon
-
: MP3 file icon.
-
: JPG file icon.
-
: CD file icon.
-
: Folder file icon
-
: current file icon
English
Using the Zoom Function
Folder Selection
Clips Menu for
MP3/WMA/JPEG/CD Audio
CD Audio or discs with MP3/WMA/JPEG contain
individual songs and/or pictures that can be organized into folders as shown below. They are similar
to how you use your computer to put files into different folders.
Open the disc tray.
Place the disc on the tray.
Close the tray.
The tray closes and this
screen displays.
001/004
Off
- To select the Parent Folder
Press the RETURN button to go to parent folder, or press the
œ/ƒ
ƒ buttons to select “..” and press ENTER to go to the
parent folder.
MP3/WMA/CD Audio Playback
1. Open the disc tray. Place the disc on the tray. Close the tray.
- Only one kind of file is played back when a disc or a
folder contains both MP3 and WMA files.
ƒ buttons to select a song file.
2. Press the œ/ƒ
Press ENTER to begin playback of the song file.
00:01 03:12
Off
001/004
128kbps
track 1
track 2
track 3
track 4
-
: Current Playback Mode : There are four
modes. They can be selected in order by
pressing the REPEAT button.
- Off: Normal Playback
- Track: Repeats the current track.
- Folder: Repeats the current folder.
- Random: Files in the disc will be played in
random order.
Repeat/Random playback
Press the REPEAT button to change the playback mode. There
are four modes, such as Off, Track, Folder and Random.
- Off: Normal Playback
- Track: Repeats the current song file.
- Folder: Repeats the song files which have the same
extension in the current folder.
- Random: Song files which have the same extension will be
played in random order.
17
CD-R MP3/WMA file
When you record MP3 or WMA files on CD-R, please refer
to the following.
- Your MP3 or WMA files should be ISO 9660 or JOLIET
format.
ISO 9660 format and Joliet MP3 or WMA files are
compatible with Microsoft's DOS and Windows, and with
Apple's Mac. This format is the most widely used.
- When naming your MP3 or WMA files, do not exceed 8
characters, and enter “.mp3, .wma” as the file extension.
General name format : Title.mp3. or Title.wma. When
composing your title, make sure that you use 8 characters or
less, have no spaces in the name, and avoid the use of
special characters including: (.,/,\,=,+).
- Use a decompression transfer rate of at least 128 Kbps
when recording MP3 files.
Sound quality with MP3 files basically depends on the rate of
compression/decompression you choose. Getting CD audio
sound requires an analog/digital sampling rate, that is
conversion to MP3 format, of at least 128 Kbps and up to 160
Kbps. However, choosing higher rates, like 192 Kbps or more,
only rarely give better sound quality. Conversely, files with
decompression rates below 128 Kbps will not be played
properly.
- Use a decompression transfer rate of at least 64Kbps
when recording WMA files.
Sound quality with WMA files basically depends on the rate of
compression/decompression you choose.
Getting CD audio sound requires an analog/digital sampling
rate, that is conversion to WMA format, of at least 64Kbps
and up to 192Kbps. Conversely, files with decompression
rates below 64Kbps or over 192Kbps will not be played
properly.
- Do not try recording copyright protected MP3 files.
Certain "secured" files are encrypted and code protected to
prevent illegal copying. These files are of the following types:
TM
Windows Media (registered trade mark of Microsoft Inc) and
TM
SDMI (registered trade mark of The SDMI Foundation). You
cannot copy such files.
- Important:
The above recommendations cannot be taken as a
guarantee that the DVD player will play MP3 recordings, or as
an assurance of sound quality. You should note that certain
technologies and methods for MP3 file recording on CD-Rs
prevent optimal playback of these files on your DVD player
(degraded sound quality and in some cases, inability of the
player to read the files).
- This unit can play a maximum of 500 files and 500 folders
per disc.
18
Picture CD Playback
1. Select the desired folder.
ƒ buttons to select a Picture file in the clips
2. Press the œ/ƒ
menu and then press the ENTER button.
Rotation
- Each time the ¦/‹button is pressed,the picture
rotates 90 degree clockwise.
- Each time the œ button is pressed,the picture
rotate 180 degree.
- Each time the ƒ button is pressed,the picture
go to miror appearance.
Zoom
- Each time number 7 is pressed, the picture is
enlarged.
zoom mode : 100% -125%-150%-200%-100% .
Slide show
- When you press the ENTER/PLAY at JPEG file,it
will go to full screen mode and automaically slide
show.
Note
- Depending on a file size, the amount of time
between each picture may be different from the
manual.
- If you don’t press any button, the slide show will
start automatically in about 8 seconds by default.
CHANGING SETUP
MENU
Using the Setup Menu
- Only files with the “.jpg” and “.JPG” extensions can be played.
- If the disc is not closed, it will take longer to start playing and
not all of the recorded files may be played.
- Only CD-R discs with JPEG files in ISO 9660 or Joliet format
can be played.
- The name of the JPEG file may not be longer than 8
characters and should contain no blank spaces or special
characters (. / = +).
- Only a consecutively written multi-session disc can be played.
If there is a blank segment in the multi-session disc, the disc
can be played only up to the blank segment.
- A maximum of 500 images can be stored on a single CD.
- Kodak Picture CDs are recommended.
- When playing a Kodak Picture CD, only the JPEG files in the
pictures folder can be played.
- When playing a Kodak Picture CD, only the JPEG files in the
pictures folder can be played.
- Kodak Picture CD: The JPEG files in the pictures folder can
be played automatically.
- Konica Picture CD: If you want to see the Picture, select the
JPEG files in the clips menu.
- Fuji Picture CD: If you want to see the Picture, select the
JPEG files in the clips menu.
- QSS Picture CD: The unit may not play QSS Picture CD.
- If the number of files in 1 Disc is over 500, only 500 JPEG
files can be played.
- If the number of folders in 1 Disc is over 500, only JPEG
files in 500 folders can be played
The Setup menu lets you customize your DVD player by allowing you to select various language preferences, set up a parental level, even adjust the player to the type of television screen you have.
1. Press the MENU button on the remote control.Use the ¦/‹
buttons to select Setup, then press the ƒ or ENTER
button.
.. Language Setup
Player Menu
Disc Menu
Audio
Subtitle
Page .. ..
ENG
ENG
ORI
AUTO
❶ Language Setup page: Setup of the Language.
❷ Audio Setup page: Setup of the Audio Options.
❸ Display Setup page: Setup of the Display Options. Use
to select which type of screen you want to watch and
several display options.
❹ Parental Setup page: Setup of the Parental Level. Allows
users to set the level necessary to prevent children from
viewing unsuitable movies such as those with violence,
adult subject matter, etc.
2. Press the ¦/‹ buttons to access the different features.
Press the ƒ or ENTER button to access the sub features.
3. To make the setup screen disappear after setting up, press
the MENU button again.
Note
Depending on the disc, some Setup Menu selections may not work.
19
English
CD-R JPEG Discs
Setting Up the Language
Features
If you set the player menu, disc menu, audio and
subtitle language in advance, they will come up
automatically every time you watch a movie.
Using the Player Menu Language
1. Press the MENU button.
2. Press the ¦/‹ buttons to select Language Setup, then
press the ƒ or ENTER button.
ƒ buttons to select Player Menu, then press
3. Press the œ/ƒ
the ‹ or ENTER button.
ƒ buttons to select the desired language,
4. Press the œ/ƒ
then press ENTER button.
- The language is selected and the screen
returns to Language Setup page.
- To make the setup menu disappear, press the MENU
button.
Using the Audio Language
1. Press the MENU button.
2. Press the ¦/‹ buttons to select Language Setup page,
then press the ƒ or ENTER button.
ƒ buttons to select Audio, then press ENTER
3. Press the œ/ƒ
button.
ƒ buttons to select the desired language, then
4. Press the œ/ƒ
press ENTER button.
- Select “Original” if you want the default soundtrack
language to be the original language the disc is
recorded in.
- If the selected language is not recorded on the disc, the
original pre-recorded language is selected.
- The language is selected and the screen returns to
Language Setup menu.
- To make the setup menu disappear, press the MENU
button.
.. Language Setup Page .. ..
Player Menu
ENG
Disc Menu
ENG
Audio
ORI
Subtitle
AUTO
Original
English
Français
Deutsch
Español
Italiano
Nederlands
Using the Subtitle Language
Using the Disc Menu Language
This function changes the text language only on the
disc menu screens.
1. Press the MENU button.
2. Press the ¦/‹ buttons to select Language Setup page,
then press the ƒ or ENTER button.
ƒ buttons to select Disc Menu, then press
3. Press the œ/ƒ
the ENTER button.
ƒ buttons to select the desired language,
4. Press the œ/ƒ
then press the ENTER button.
- The language is selected and the screen returns to
Language Setup page
- To make the setup menu disappear, press the MENU
button.
1. Press the MENU button.
2. Press the ¦/‹ buttons to select Language Setup, then
press the ƒ or ENTER button.
ƒ buttons to select Subtitle, then press the ‹
3. Press the œ/ƒ
or ENTER button.
ƒ buttons to select the desired language,
4. Press the œ/ƒ
then press the ENTER button.
- Select “Automatic” if you want the subtitle language to
be the same as the language selected as the audio
language.
- Some discs may not contain the language you select as
your initial language; in that case the disc will use its
original language setting.
- The language is selected and the screen returns to
setup menu.
- To make the setup menu disappear, press the MENU
button.
.. Language Setup Page .. ..
20
Player Menu
ENG
Disc Menu
ENG
Audio
ORI
Subtitle
AUTO
English
Français
Deutsch
Español
Italiano
Nederlands
Cesky
.. Language Setup Page .. ..
Player Menu
ENG
Disc Menu
ENG
Audio
ORI
Subtitle
AUTO
Automatic
English
Français
Deutsch
Español
Italiano
Nederlands
Audio Options allows you to setup the audio device
and sound status settings depending on the audio
system in use.
1. Press the MENU button.
2. Press the ¦/‹ buttons to select Audio Setup, then
press the ƒ or ENTER button.
ƒ buttons to select the desired item, then
3. Press the œ/ƒ
press the ‹ or ENTER button.
“DTS” and “DTS Digital Out” are trademarks of
Digital Theater Systems, Inc.
Setting Up the Display
Options
Display options enable you to set various video
functions of the player.
.. Audio Setup Page ..
Dolby Digital Out
MPEG2 Digital Output
Dynamic Compression
PCM Down Sampling
.. Audio Setup Page ..
Dolby Digital Out
MPEG2 Digital Output
Dynamic Compression
PCM Down Sampling
Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D symbol
are trademarks of Dolby Laboratories.
English
Setting Up the Audio
Options
PCM
PCM
On
On
PCM
PCM
On
On
1. Press the MENU button.
2. Press the ¦/‹ buttons to select Display Setup page
then press the ƒ or ENTER button.
ƒ buttons to select the desired item, then
3. Press the œ/ƒ
press the ‹ or ENTER button.
PCM
BItstream
❶ Dolby Digital Out
- PCM : Converts to PCM(2CH) audio.
- Bitstream : Outputs Dolby Digital via the digital out
put.Select Bitstream when connecting to a
Dolby Digital Decoder.
❷ MPEG-2 Digital Output
- PCM : Converts to PCM(2CH) audio.
- Bitstream : Converts to MPEG-2 Digital Bitstream
(5.1CH or 8CH). Select Bitstream when using the
Digital Audio Output.
❸ Dynamic Compression
- On : To select dynamic compression.
- Off : To select the standard range.
❹ PCM Down Sampling
- On : Select this when the Amplifier connected to the
player is not 96KHz compatible. In this case, the
96KHz signals will be down converted to 48KHZ.
- Off : Select this when the Amplifier connected to the
player is 96KHz compatible. In this case, all sig
nals will be output without any changes.
Note
Even when PCM Down sampling is Off
• Some discs will only output down sampled
audio through the digital outputs.
• To make the Setup menu disappear, press the
MENU button.
.. Display Setup Page ..
Tv Aspect
4:3 LB
Screen Message
On
Video Output
I-Scan
Black Level
Off
TV System
PAL
❶ TV Aspect
Depending on a type of television you have, you
may want to adjust the screen setting (aspect
ratio).
- 4:3 Pan&Scan : Select this for conventional
size TVs when you want to see the central portion of the 16:9 screen. (Extreme left and right
side of movie picture will be cut off.)
- 4:3 Letter Box : Select when you want to see
the total 16:9 ratio screen DVD
supplies, even though you have a TV with a 4:3
ratio screen. Black bars will appear at the top
and bottom of the screen.
- 16:9 Wide : You can view the full 16:9
picture on your wide screen TV.
.. Display Setup Page ..
Tv Aspect
4:3 LB
Screen Message
On
Video Output
I-Scan
Black Level
Off
TV System
PAL
4:3 Pan&Scan
4:3 letter Box
16:9 Wide
21
❷ Screen Message
Use to turn on-screen messages On or Off.
❸
Video Output
The Parental Control function works in conjunction
with DVDs that have been assigned a rating, which
helps you control the types of DVDs that your family
watches. There are up to 8 rating levels on a disc.
(Only for model DVD-P181/DVD-P181K)
.. Display Setup Page ..
Tv Aspect
4:3 LB
Screen Message
On
Video Output
I-Scan
Black Level
Off
TV System
PAL
❹
Setting Up the Parental
Control
Setting Up the Rating Level
P-SCAN
I-SCAN
1. Press the MENU button.
2. Press the ¦/‹ buttons to select parental setup page,
then press the ƒ or ENTER button.
Black Level
Adjusts the brightness of the screen.
➎ TV System
- NTSC : In case of using NTSC disc
• If your TV system only has PAL-Video input,
you must choose “PAL”. When you choose
“PAL”, Interlace output format is PAL 60 Hz
output.
• If your TV system only has NTSC, input you
must choose “NTSC ”.
• If you set up the NTSC TV system
- PAL : In case of using PAL disc
• If your TV system only has NTSC-Video input,
you must choose “NTSC”.
• If your TV system only has PAL input, you
must choose “PAL ”.
• If you set up the PAL TV system.
.. Display Setup Page ..
Tv Aspect
4:3 LB
Screen Message
On
Video Output
I-Scan
Black Level
Off
TV System
PAL
.. Parental Page ..
Parental
Password
ƒ buttons to select Parental, then press the
3. Press the œ/ƒ
‹ or ENTER button.
ƒ buttons to select the Rating Level you want,
4. Press the œ/ƒ
then press the ENTER button.
e.g) Setting up in KID SAFE
.. Parental Page ..
Parental
Password
PAL
AUTO
NTSC
5. Enter your password.
- By default, password is set to 0000.
Password
Cancel
22
N t
2G
3 PG
4 PG 13
5 PGR
6R
7 NC17
8 ADULT
❶ KID SAFE
❷ G(General Audiences) : All Ages Admitted
❸ PG(Parental Guidance suggested): Some material may
not be suitable for young children.
❹ PG-13 (PG-13-Parents strongly cautioned) : Some material
may be inapproriate for children under 13
❺ PGR ( parental guidance Recommended): These are not
necessarily unsuitable for children, but viewer discretion is
advised, and parents and guardians are encouraged to
supervise younger viewers.
❻ R( Restricted): Under 17 requires accompanying adult
❼ NC17( NC-17) : No one 17 and under admitted
❽ Adult
Note
If you have forgotten your password, see
“Forgot Password” in the Troubleshooting Guide.
Note
• To make the setup menu disappear, press the
MENU button. For example, if you select up to
level R, discs that contain NC17, Adult will not
play.
Changing the Password
1. Press the MENU button.
2. Press the ¦/‹ buttons to select parental setup page,
then press the ƒ or ENTER button.
.. Language Setup Page ..
Player Menu
ENG
Disc Menu
ENG
Audio
ORI
Subtitle
AUTO
ƒ buttons to select PASSWORD, then
3. Press the œ/ƒ
press the ‹ or ENTER button.
.. Parental Page ..
Parental
Password
4. The Enter password screen appear. Enter your pasword
(default password), Enter the new password again
.. Parental Page ..
Parental
Password
Change
23
English
Note
REFERENCE
Firmware upgrade
Introduction
Samsung will often support the software upgrade
to improve the performance of this unit to the
lastest status , trough samsung Internet
Site(www.samsung.com)
2.Press enter or play to start upgrade.
- Other key to cancel upgrade back to samsung logo and eject the disc.
Upgrade file detected
Curent version: 07.12.15.00
Upgrade ?
Press Play to start
File copying
Firmware upgrade starts
What improvements are made depends on the
upgrade software your are using as well as the
software that your DVD-player contained before
the upgrde.
Upgrade file detected
Curent version: 07.12.15.00
Upgrade ?
Press Play to start
Upgrade
Firmware upgrade starts
How to make an upgrade disc
Write the downloaded file onto a blank CD-R or CDRW disc, using the following settings:
1. You have to download a new file trough Download
center of Samsung Internet Site (http://www.samsung.com).
2. Write the file to disc using CD-RW driver of your
- In the middle of the writing, the tray will open
automatically. After taking out the disc, please
wait for about 2 minutes.
- If the unit was succesfully update, the unit will
turn off and on after closing the tray automatically.
When the unit turns on, this screen will display.
3.Press the number buttons to select the
desired language
computer.
Note
- File system CD-ROM
- Chracteer set ISO 9660
- Finalized, single session
- Write speed low
Update procedure
1.Open the disc tray. Place disc the on the tray.
close the tray. The Firm ware Upgrade sreen
appears.
Upgrade file detected
Curent version: 07.12.15.00
Upgrade ?
Press Play to start
Firmware upgrade
appears on the display
24
Note
- If the “Select Menu Language”doesn’t appear,
please contact to “Samsung Service Center- If
the unit was succesfully update, the unit will
turn off and on after closing the tray automatical
- Do not press any button and plug the power code
during upgrade.
- The upgrade procedure may change, refer to the
web site( www.samsung.com)
Troubleshooting
Before requesting service (troubleshooting), please check the following.
Page
No operations can be
performed with the
remote control.
• Check the batteries in the remote control.
They may need replacing.
• Operate the remote control at a distance of no more than 20 feet.
• Remove batteries and hold down one or more buttons for several minutes to drain
the microprocessor inside the remote control to reset it. Reinstall batteries and try
to operate the remote control again.
P3
Disc does not play.
• Ensure that the disc is installed with the label side facing up.
• Check the region number of the DVD.
P5
5.1 channel sound is
not being reproduced.
The
icon appears
on screen.
• 5.1 channel sound is reproduced only when the following conditions are met. :
1) The DVD player is connected with the proper Amplifier
2) The disc is recorded with 5.1 channel sound.
• Check whether the disc being played has the “5.1 ch” mark on the outside.
• Check if your audio system is connected and working properly.
• In a SETUP Menu, is the Audio Output set to Bitstream?
• The features or action cannot be completed at this time because:
1. The DVD’s software restricts it.
2. The DVD’s software doesn’t support the feature (e.g., angles).
3. The feature is not available at the moment.
4. You’ve requested a title or chapter number or search time that is out of range.
English
Action
Problem
P10-11
P21
Disc Menu doesn’t appear. • Check if the disc has a Menu.
Play mode differs from the
Setup Menu selection.
• Some of the functions selected in the Setup Menu may not work properly if the
disc is not encoded with the corresponding function.
P19-23
The screen ratio
cannot be changed.
• The Screen Ratio is fixed on your DVDs.
P21-22
No audio.
• Make sure you have selected the correct Digital Output in the Audio Options
Menu.
The screen is blocked
• Press the
button (in front panel) for more than 5 seconds under no disc
inside. All settings will revert to the factory settings.
Forgot password
P21
• Press the
button (in front panel ) for more than 5 seconds
under no disc inside. All settings including the password will revert to the factory
settings. Don't use this unless absolutely necessary.
If you experience
other problems.
• Go to the contents and find the section of the instruction book that contains the
explanations regarding the current problem, and follow the procedure once again.
• If the problem still cannot be solved, please contact your nearest authorized service center.
The picture is noisy or
distorted
• Make sure that the disc is not dirty or scratched.
• Clean the disc.
P12
P22
P2
25
Specifications
General
Power Requirements
AC 110-240 V, 50/60 Hz
Power Consumption
9W
Weight
1.3 Kg
Dimensions
360mm (W) X 200mm (D) X 37mm (H)
+5°C to +35°C
Operating Temperature Range
Operating Humidity Range
10 % to 75 %
DVD
(DIGITAL VERSATILE DISC)
Disc
Reading Speed : 3.49 ~ 4.06 m/sec.
Approx. Play Time
(Single Sided, Single Layer Disc) : 135 min.
CD : 12Cm
(COMPACT DISC)
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 74 min.
CD : 8Cm
(COMPACT DISC)
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 20 min.o)
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 74 min. (Video + Audio)
VCD : 12Cm
Video
Output
Composite Video
1 channel : 1.0 Vp-p (75 Ω load)
*Frequency Response
Audio
Output
48 kHz Sampling : 4 Hz to 22 kHz
96 kHz Sampling : 4 Hz to 44 kHz
*S/N Ratio
*Dynamic Range
110 dB
*Total Harmonic Distortion
100 dB
0.004 %
*: Nominal specification
- Samsung Electronics Co., Ltd reserves the right to change the specifications without
notice.
- Weight and dimensions are approximate.
26
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer
care center.
Latin America
Country
CANADA
MEXICO
U.S.A
ARGENTINE
BRAZIL
CHILE
NICARAGUA
HONDURAS
COSTA RICA
ECUADOR
EL SALVADOR
GUATEMALA
JAMAICA
PANAMA
PUERTO RICO
REP. DOMINICA
TRINIDAD & TOBAGO
VENEZUELA
COLOMBIA
BELGIUM
CZECH REPUBLIC
DENMARK
FINLAND
FRANCE
Europe
CIS
Asia Pacific
Middle East &
Africa
Customer Care Center 1-800-SAMSUNG(726-7864)
01-800-SAMSUNG(726-7864)
1-800-SAMSUNG(726-7864)
0800-333-3733
0800-124-421 , 4004-0000
800-SAMSUNG(726-7864)
00-1800-5077267
800-7919267
0-800-507-7267
1-800-10-7267
800-6225
1-800-299-0013
1-800-234-7267
800-7267
1-800-682-3180
1-800-751-2676
1-800-SAMSUNG(726-7864)
0-800-100-5303
01-8000112112
0032 (0)2 201 24 18
844 000 844
Distributor pro Českou republiku:
Samsung Zrt., česka organizační složka
Vyskočilova 4, 14000 Praha 4
70 70 19 70
030-6227 515
3260 SAMSUNG ( 0,15/Min),
08 25 08 65 65 ( 0,15/Min)
Web Site
www.samsung.com/ca
www.samsung.com
www.samsung.com
www.samsung.com/ar
www.samsung.com
www.samsung.com/cl
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com.co
www.samsung.com/be
www.samsung.com/cz
www.samsung.com/dk
www.samsung.com/fi
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com/be
www.samsung.com/nl
www.samsung.com/no
www.samsung.com/pl
www.samsung.com/pt
www.samsung.com/sk
www.samsung.com
www.samsung.com/se
www.samsung.com
www.samsung.com/ie
www.samsung.com/at
www.samsung.com/ch
www.samsung.com
www.samsung.kz
www.samsung.uz
GERMANY
HUNGARY
ITALIA
LUXEMBURG
NETHERLANDS
NORWAY
POLAND
PORTUGAL
SLOVAKIA
SPAIN
SWEDEN
U.K
EIRE
AUSTRIA
SWITZERLAND
RUSSIA
KAZAHSTAN
UZBEKISTAN
KYRGYZSTAN
TADJIKISTAN
UKRAINE
LITHUANIA
LATVIA
ESTONIA
AUSTRALIA
NEW ZEALAND
CHINA
HONG KONG
INDIA
INDONESIA
JAPAN
MALAYSIA
PHILIPPINES
SINGAPORE
THAILAND
TAIWAN
VIETNAM
TURKEY
0900-SAMSUNG(726-7864) ( 0,10/Min)
815-56 480
0 801 801 881 , 022-607-93-33
80820-SAMSUNG(726-7864)
0800-SAMSUNG(726-7864)
902 10 11 30
0771-400 200
0845 SAMSUNG (7267864)
0818 717 100
0800-SAMSUNG(726-7864)
0800-SAMSUNG(726-7864)
8-800-555-55-55
8-10-800-500-55-500
8-10-800-500-55-500
00-800-500-55-500
8-10-800-500-55-500
8-800-502-0000
8-800-77777
800-7267
800-7267
1300 362 603
0800SAMSUNG(726-7864)
800-810-5858 , 010-6475 1880
3698-4698
3030 8282 , 1800 110011
0800-112-8888
0120-327-527
1800-88-9999
1800-10-SAMSUNG(726-7864)
1800-SAMSUNG(726-7864)
1800-29-3232 , 02-689-3232
0800-329-999
1 800 588 889
444 77 11
www.samsung.com
www.samsung.lt
www.samsung.com/lv
www.samsung.ee
www.samsung.com
www.samsung.com/nz
www.samsung.com
www.samsung.com/hk
www.samsung.com
www.samsung.com
www.samsung.com/jp
www.samsung.com/my
www.samsung.com/ph
www.samsung.com
www.samsung.com
www.samsung.com/tw
www.samsung.com
www.samsung.com
SOUTH AFRICA
0860-SAMSUNG(726-7864 )
www.samsung.com
U.A.E
800-SAMSUNG (726-7864), 8000-4726
www.samsung.com
01805 - SAMSUNG(726-7864) (
06-80-SAMSUNG(726-7864)
800-SAMSUNG(726-7864)
0035 (0)2 261 03 710
English
Region
North America
0,14/Min)
27
Memo
Memo
Download PDF