Samsung | PS-42S4S | Samsung PS-42S4S User Manual

BN68-00742A-00Eng_0621
2004.6.21
3:51 PM
Page 1
PDP-TELEVISION
(PLASMA DISPLAY PANEL)
Owner’s Instructions
Before operating the unit,
please read this manual thoroughly,
and retain it for future reference.
ON-SCREEN MENUS
PICTURE IN PICTURE (PIP)
COLOUR WEAKNESS ENHANCEMENT MODE
MY COLOUR CONTROL
TELETEXT (OPTION)
SRS TRUSURROUNDXT
DIGITAL NATURAL IMAGE ENGINE
BN68-00742A-00Eng_0621
2004.6.21
3:51 PM
Page 2
User Instructions
ENG
◆ Screen Image retention
Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the
plasma monitor panel for more than 2 hours as it can cause screen image retention. This image
retention is also known as “screen burn”. To avoid such image retention, reduce the degree of
brightness and contrast of this screen when displaying a still image.
◆ Cell Defect
The plasma display panel consists of fine cells. Although the panels are produced with more than
99.9 percent active cells, there may be some cells that do not produce light or remain lit.
◆ Height
The PDP can normally operate only under 2000m in height. It might abnormally function at a place
over 2000m in height and do not install and operate there.
◆ Heat
PDP TV displays picture by Plasma discharge. For this reason, using the PDP TV for a long period of
time results in dissipation of heat by the panel.
Please note that the top side of the product may be hot after use for long periods of time as the heat
dissipation from the panel through the vent hole in the upper part of the product.
You don't have to worry since PDP TV’s heat dissipation does not necessarily indicate any defect or
operation failure of the product.
Particularly when watching TV with children, adults should prevent children from touching the upper
part of the product.
◆ Warranty
- Warranty does not cover any damage caused by image retention.
- Burn-in is not covered by the warranty.
2
BN68-00742A-00Eng_0621
2004.6.21
3:51 PM
Page 3
ENG
Checking Parts
Sold Separately
S-VIDEO Cable
DVI Cable
Component Cables
(RCA)
PC Cable
Owner’s Instructions
Remote Control/
AAA Batteries
Power Cord
Antenna Cable
PC Audio Cable
DNIeTM (Digital Natural Image engine)
This feature bring you more detailed image with 3D noise
reduction, detail enhancement, contrast enhancement and
white enhancement. New image compensation Algorithm gives
brighter, clearer, much detailed image to you. DNIeTM
technology will fit every signals into your eyes.
3
BN68-00742A-00Eng_0621
2004.6.21
3:51 PM
Page 4
ENG
Contents
◆ FOREWORD
■
User Instructions............................................................................................
2
◆ CONNECTING AND PREPARING YOUR DISPLAY
■
■
■
■
■
■
■
■
■
■
■
■
■
Your New Plasma Display Panel...................................................................
Infrared Remote Control ................................................................................
Inserting the Batteries in the Remote Control................................................
Assembling the Stand-Base ..........................................................................
Installing the Display on the Wall Attachment Panel .....................................
Connecting to an Aerial or Cable Television Network ...................................
Connecting a Satellite Receiver or Decoder..................................................
Switching On and Off.....................................................................................
Placing in Standby Mode...............................................................................
Becoming Familiar with the Remote Control .................................................
Setting Up Your Remote Control ...................................................................
Plug & Play Feature.......................................................................................
Choosing Your Language..............................................................................
6
8
9
9
10
12
12
13
13
14
15
16
17
◆ SETTING THE CHANNELS
■
■
■
■
■
■
■
■
Storing Channels Automatically.....................................................................
Storing Channels Manually............................................................................
Skipping Unwanted Channels .......................................................................
Sorting the Stored Channels .........................................................................
Assigning Names to Channels ......................................................................
Using the LNA (Low Noise Amplifier) Feature...............................................
Activating the Child Lock ...............................................................................
Displaying Information ...................................................................................
18
19
21
22
23
24
25
26
◆ USING YOUR DISPLAY
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
4
Changing the Picture Standard .....................................................................
Adjusting the Picture Settings........................................................................
Adjusting the Picture Settings (PC or DVI Mode) ..........................................
Setting the Picture (PC Mode).......................................................................
Using the Fine Tune ......................................................................................
Viewing the Channel Scan Picture ................................................................
Freezing the Current Picture .........................................................................
Selecting the Picture Size..............................................................................
Selecting the Film Mode ................................................................................
DNIeTM (Digital Natural Image engine
) ...............................................
Setting the My Colour Control Mode .............................................................
Using the Colour Weakness Enhancement Option .......................................
Setting the Blue Screen.................................................................................
Setting the Melody Sound .............................................................................
Viewing the Picture In Picture (PIP) ..............................................................
26
27
28
29
31
32
32
33
34
35
36
39
40
41
42
BN68-00742A-00Eng_0621
2004.6.21
3:51 PM
Page 5
ENG
Contents (continued)
◆ USING YOUR DISPLAY (continued)
■
■
■
■
■
■
■
■
■
■
■
■
Using the Digital NR (Digital Noise Reduction) Feature ................................
Protecting the Screen Burning.......................................................................
Changing the Sound Standard ......................................................................
Adjusting the Sound Settings ........................................................................
Adjusting the Volume Automatically ..............................................................
Setting the TruSurround XT...........................................................................
Selecting the Internal mute............................................................................
Selecting the Sound Mode (depending on the model) ..................................
Setting the Sleep Timer .................................................................................
Setting and Displaying the Current Time.......................................................
Switching the Television On and Off Automatically .......................................
Viewing an External Signal Source ...............................................................
45
46
47
48
49
50
51
52
53
54
55
56
◆ USING THE TELETEXT FEATURE
■
■
■
■
Teletext Feature ............................................................................................
Displaying the Teletext Information ...............................................................
Selecting Display Options..............................................................................
Selecting a Teletext Page..............................................................................
57
58
59
60
◆ ADDITIONAL INFORMATION AND CONNECTIONS
■
■
■
■
■
■
■
■
■
Connecting to the External Devices ..............................................................
Connecting to the S-Video Input....................................................................
Connecting to the DVI Input ..........................................................................
Connecting to the PC Input ...........................................................................
Connecting to the Component Input..............................................................
Connecting and Using the Home Theater System ........................................
Setting up Your PC Software (Windows only) ...............................................
Input Mode (PC/DVI) .....................................................................................
Pin Configurations .........................................................................................
61
62
63
63
64
65
66
67
68
◆ RECOMMENDATIONS FOR USE
■
■
Troubleshooting: Before Contacting Service Personnel................................
Programming the Remote Control for Other Components ............................
Symbols
Press
☛
Important
➢
Note
5
69
70
BN68-00742A-00Eng_0621
2004.6.21
3:51 PM
Page 6
Your New Plasma Display Panel
➢
ENG
The actual configuration on your PDP may be different,
depending on your model.
Front Panel
a
b
Speaker
a
c
Touch button
Touch the printed names
of each button using your
finger to operate it.
b
SOURCE
I/
External input selection.
Press to turn the PDP on and off.
MENU
Power Indicator
Menu display.
- Power Off: Blue
- Power On: Off
- VOL +
Volume adjustment.
Also used to select or adjust items
on the on-screen menu.
c
Remote Control Signal Receiver
† CH …
Channel selection. Auto power On.
Also used to move up or down in the on-screen
menu.
Confirm your choice (Store or Enter)
6
Aim the remote control towards this spot on
the PDP.
BN68-00742A-00Eng_0621
2004.6.21
3:51 PM
Page 7
Your New Plasma Display Panel (continued)
➢
The actual configuration on your PDP may be different,
depending on your model.
ENG
Side of the TV
S-Video Input
Video Input
Audio Input (L, R)
Rear Panel
➢
For further details about connection, refer to pages 61~65.
a) DVI INPUT (DVI-D / L-AUDIO-R)
Connect to the digital video and audio
output jack of a device with DVI output.
f) S-VIDEO1, S-VIDEO2
(S-VIDEO1 or S-VIDEO2 / L-AUDIO-R)
Video and audio inputs for external devices with
an S-Video output, such as a camcorder or VCR.
b) MONITOR OUT (VIDEO / L-AUDIO-R)
Outputs for external devices.
c) ANT IN VHF/UHF (75Ω)
75Ω Coaxial connector for Aerial/Cable Network.
d) PC INPUT (RGB IN / AUDIO)
Connect to the video and audio output jack on
your PC.
e) ONLY FOR SERVICE
Connector for service only.
g) AV1, AV2, AV3
(VIDEO / L-AUDIO-R)
Video and audio inputs for external devices,
such as a camcorder or VCR.
h) COMPONENT1, COMPONENT2
Video (Y/Pb/Pr) and audio (L-AUDIO-R) inputs for
Component.
i) POWER IN
Connect the supplied power cord.
7
BN68-00742A-00Eng_0621
2004.6.21
3:51 PM
Page 8
Infrared Remote Control
ENG
TURNS THE PDP ON AND OFF
WHEN YOU PRESS A BUTTON , ‘
’
APPEARS ALONG WITH SELECTED MODE
(TV, VCR, CATV, DVD OR STB) AND
REMAINING BATTERIES ON LCD
PICTURE EFFECT SELECTION
SOUND EFFECT SELECTION
TELETEXT CANCEL
MAKE THE REMOTE CONTROL WORKS
FOR TV, VCR, CATV, DVD PLAYER, STB
DIRECT CHANNEL SELECTION
AUTOMATIC SWITCH-OFF/
TELETEXT SUB-PAGE
PICTURE SIZE/
TELETEXT SIZE SELECTION
VOLUME INCREASE
TEMPORARY SOUND SWITCH-OFF
VOLUME DECREASE
TELETEXT DISPLAY/
MIX BOTH TELETEXT INFORMATION
AND THE NORMAL BROADCAST
MENU DISPLAY/
TELETEXT INDEX
NEXT CHANNEL/
TELETEXT NEXT PAGE
EXTERNAL INPUT SELECTION/
TELETEXT PAGE HOLD
PREVIOUS CHANNEL/
TELETEXT PREVIOUS PAGE
INFORMATION DISPLAY/
TELETEXT REVEAL
TV MODE SELECTION
EXIT TELETEXT
(DEPENDING ON THE MODEL)
MOVE TO THE REQUIRED
MENU OPTION/
ADJUST AN OPTION VALUE
RESPECTIVELY
PICTURE STILL
DNIe ON/DEMO/OFF
FASTEXT TOPIC SELECTION
REMOTE CONTROL SETUP
IF YOUR REMOTE CONTROL IS NOT
FUNCTIONING PROPERLY, TAKE
OUT THE BATTERIES AND PRESS
THE RESET BUTTON FOR ABOUT
2~3 SECONDS. RE-INSERT THE
BATTERIES AND TRY USING THE
REMOTE CONTROL AGAIN.
➢
8
CONFIRM YOUR CHOICE
(STORE OR ENTER)
SOUND MODE SELECTION
TruSurround XT
MODE SELECTION
PIP FUNCTIONS:
- PIP ACTIVATING OR DEACTIVATING
(PIP ON)
- SWAPPING THE MAIN AND THE SUB
PICTURE (SWAP)
- LOCATION SELECTION (POSITION)
- SOURCE SELECTION (SOURCE)
- SIZE SELECTION (SIZE)
- SCAN
- SELECTING THE CHANNEL OF SUB
PICTURE (P
)
VCR/DVD FUNCTIONS:
- REWIND (REW)
- STOP
- PLAY/PAUSE
- FAST FORWARD (FF)
The performance of the remote control may be affected by bright light.
BN68-00742A-00Eng_0621
2004.6.21
3:51 PM
Page 9
Inserting the Batteries in the Remote Control
ENG
You must insert or replace the batteries in the remote control when
you:
◆ Purchase the PDP
◆ Find that the remote control is no longer operating
correctly
1
Remove the cover on the rear of the remote control by pressing
the symbol ( ) downwards and then pulling firmly to remove it.
2
Insert two R03, UM4, “AAA” 1.5V or equivalent batteries taking
care to respect the polarities:
◆ - on the battery against - on the remote control
◆ + on the battery against + on the remote control
3
Replace the cover by aligning it with the base of the remote
control and pressing it back into place.
Assembling the Stand-Base
1
Assemble two support pins with the stand base and firmly secure
both sides of the support pins using 8 screws provided.
2
Assemble the PDP with the stand and firmly secure the PDP using
4 screws provided.
➢
◆ Two or more people should carry the PDP. Never lay the
PDP on the floor because of possible damage to the screen.
Always store the PDP upright.
9
BN68-00742A-00Eng_0621
2004.6.21
3:51 PM
Page 10
Installing the Display on the Wall Attachment Panel
ENG
Installation Notes
◆ Do not install the PDP on any place other than vertical walls.
◆ To protect the performance of the PDP and prevent troubles, avoid the followings:
- Do not install next to smoke and fire detectors.
- Do not install in an area subjected to vibration or high voltage.
- Do not install near or around any heating apparatus.
◆ Use only recommended parts and components.
Mounting Kits
Wall Mount Bracket
Plastic Hanger
Screws
4 EA
4 EA
How to Adjust Mounting Angle
(depending on your model)
The wall mount bracket is delivered
separately. Please tighten the captive
screw in the direction of the arrow after
assembling the bracket.
10
1
Secure the PDP to the wall mount bracket.
(Please refer to the following instructions.)
2
Set the angle by pulling the upper end of the
PDP attached to bracket in the direction of the
arrow.
3
The angle can be adjusted from 0° to 15° by
±2°.
BN68-00742A-00Eng_0621
2004.6.21
3:51 PM
Page 11
Installing the Display on the Wall Attachment Panel (continued)
➢
The exterior of the PDP may be different than the picture.
(Assembly and installation of the plastic hanger is the same.)
1
Remove the screws from the back of the PDP.
2
ENG
Use the screws and assemble the plastic
hanger.
☛
◆ Please ask the installers to install the
wall mount bracket.
◆ Please be sure to check if the plastic
hanger is completely secured on both
the left and right side after hanging
the PDP on the wall mount bracket.
◆ Please avoid catching your fingers
while installing and adjusting the
angle.
◆ Please tightly secure the wall mount
bracket to the wall to avoid injury
from a falling PDP.
3
Tighten the screws of the plastic hanger to the
back side of the PDP.
4
Put the 4 pegs on the PDP in the grooves of the wall mount bracket and pull down on the PDP (!) to
secure it to the wall mount bracket (@). Tighten the screws as shown (#) so that the PDP cannot be
separated from wall mount bracket.
PDP panel
Wall
Wall attachment panel bracket
Connecting External Devices to the PDP
◆ To connect external devices such as a DVD or a Home Theater System to the PDP, please refer
to following instructions:
1
Be sure to remove the safety pins underneath the PDP.
◆ If the safety pins are not removed, the angle cannot be adjusted.
Any attempt to do so may cause damage to the PDP.
2
Pull out the bottom of the PDP (which has been attached to the Wall
Mount Bracket) in the direction indicated by the arrows (refer to
the illustration) until it clicks.
◆ Using the PDP After Connecting External Devices.
Be sure to secure the PDP by inserting the 2 safety pins after
o
readjusting the angle of the PDP to 0 .
◆ For safety, be sure to secure the PDP using the safety pins.
If the safety pins are not used, the PDP may fall, causing serious
injury.
11
BN68-00742A-00Eng_0621
2004.6.21
3:51 PM
Page 12
Connecting to an Aerial or Cable Television Network
ENG
To view television channels correctly, a signal must be received by
the set from one of the following sources:
◆ An outdoor aerial
◆ A cable television network
◆ A satellite network
Rear of the PDP
1
In the first three cases, connect the aerial or network input cable to
the 75Ω coaxial socket on the rear of the PDP.
2
If you are using an indoor aerial, you may need to turn it when
tuning your PDP until you obtain a picture that is both sharp and
clear.
For further details, refer to:
◆ “Storing Channels Automatically” on page 18
◆ “Storing Channels Manually” on page 19
or
Cable Television
Network
➢
When installing or re-installing your PDP, be sure to use the
supplied coaxial antenna cable. If you connect using a different
coaxial cable, there is risk of noise or interference to the screen
image. (You must not use another general purpose cable.
Use the 3M/5M/7M cable supplied by Samsung.)
Connecting a Satellite Receiver or Decoder
Rear of the PDP
In order to watch television programmes broadcast via a satellite
network, you must connect a satellite receiver to the rear of the
PDP. Also, in order to descramble a coded transmission signal, you
must connect a decoder to the rear of the PDP.
or
Using a Coaxial cable
Connect a coaxial cable to the:
◆ Receiver (or Decoder) output socket.
◆ Television aerial input socket.
➢
If you wish to connect both a satellite receiver (or decoder)
and a VCR, you should connect the:
◆ Receiver (or Decoder) to the VCR
◆ VCR to the PDP
Otherwise, connect the receiver (or decoder) directly to the
PDP.
Satellite receiver/
Decoder
12
BN68-00742A-00Eng_0621
2004.6.21
3:51 PM
Page 13
Switching On and Off
ENG
The mains lead is attached to the rear of your PDP.
1
Plug the mains lead into an appropriate socket.
Result:
➢
2
The main voltage is indicated on the rear of the PDP and
the frequency is 50 or 60Hz.
Press the “ I / ” button on the front of the PDP (or POWER (
button on the remote control) to switch the PDP on.
Result:
➢
3
Front of the PDP
The Standby indicator on the front of the PDP lights up.
)
The programme that you were watching last is
re-selected automatically.
If you have not yet stored any channels, No clear picture
appears. Refer to “Storing Channels Automatically” on page
18 or “Storing Channels Manually” on page 19.
To switch your PDP off, press the “ I /
TV
” button again.
Placing in Standby Mode
Your PDP can be placed in Standby mode, in order to reduce the
Power consumption.
The Standby mode can be useful when you wish to interrupt
viewing temporarily (during a meal, for example).
1
Press the POWER (
Result:
2
) button on the remote control.
The screen is turned off and the Standby indicator on
the front of the PDP lights.
To switch the PDP back on, simply press the POWER (
again or a numeric button.
➢
TV
You can also switch on by pressing the P
or
) button
button.
13
BN68-00742A-00Eng_0621
2004.6.21
3:51 PM
Page 14
Becoming Familiar with the Remote Control
ENG
The remote control is used mainly to:
◆ Change channels and adjust the volume
◆ Display the on-screen menu system
The following table presents the most frequently used buttons and
their functions.
Button
to
SLEEP
Menu Function
Used to display the next
stored channel.
-
Used to display the
previous stored channel.
-
Used to display the corresponding channels.
For double digit channels, the second digit must be
pushed immediately after the first. Failure to do this will
result in a single digit channel being displayed.
➢
Used to select a preset time interval (off - 30 - 60 - 90 - 120 150 - 180).
Used to increase the
volume.
-
Used to decrease the
volume.
-
MUTE
Used to switch the sound off temporarily.
To turn the sound back on, press this button again, or
press the
or
button.
MENU
Used to display the
on-screen menu system.
Used to return to the previous
menu or normal viewing.
-
Used to:
◆ Display a submenu
containing selections for
the current menu option
◆ Increase/decrease a
menu option value
-
Used to confirm your choice.
-
Used to exit from the menu
system and return to normal
viewing directly.
EXIT/TV
14
Viewing Function
➢
BN68-00742A-00Eng_0621
2004.6.21
3:51 PM
Page 15
Setting Up Your Remote Control
ENG
This PDP’s remote control can operate VCR, CATV , DVD, or
Set-top box (STB), in addition to controlling the PDP.
➢
The remote control is not compatible with the TV
manufactured by another company.
1
Turn off your VCR, Cable box, DVD or STB.
2
Press the SELECT button.
Mode is changed whenever SELECT button is pressed.
3
Press the POWER ( ) button on the remote control.
The component you select should turn on. If it turns on,
your remote control is now set correctly.
4
Once your remote control is set up, press the SELECT button any
time you want to use the remote control to operate your VCR,
Cable box, DVD or STB.
➢
➢
➢
➢
VCR
When your remote control is in the VCR, CATV, DVD or
STB mode, the volume buttons still control your television’s
volume.
To program the cable receiver controls:
◆ Press the SELECT button to select CATV.
◆ Point the remote control at the cable receiver and press
the SET button. Then press the company code number(s)
for the component in page 70.
Ex) If the component is manufactured by Oak, press 026.
To program the VCR controls:
◆ Press the SELECT button to select VCR
◆ Point the remote control at the VCR and press the SET
button. Then press the company code number(s) for the
component in page 71.
To program the DVD controls:
◆ Press the SELECT button to select DVD
◆ Point the remote control at the DVD and press the SET
button. Then press the company code number(s) for the
component in page 70.
15
BN68-00742A-00Eng_0621
2004.6.21
3:51 PM
Page 16
Plug & Play Feature
ENG
Plug & Play
Press ENTER to start Plug & Play
When the television is initially powered ON, several basic customer
settings proceed automatically and subsequently. The following
settings are available.
Start
Enter
Exit
1
Language
Result:
Move
3
Press the ENTER (
Result:
Move
6
Press the ENTER (
Enter
➢
Auto Store
➢
Press ENTER to start channel memory
40 MHz
0%
57 MHz
1%
Stop
Enter
Stop
Clock
Hour
Min
am/pm
07
05
am
Move
Stop
Enjoy Your Watching
16
The Auto Store menu is displayed.
) button.
The search will end automatically. Channels are sorted
and stored in an order which reflects their position in
the frequency range (with lowest first and highest last).
When it has finished, the Clock Set menu is displayed.
To stop the search before it has finished or return to normal
viewing, press the MENU (
) button.
Press the ENTER (
) button to set the clock.
8
Press the œ or √ button to move to the hour or minute.
Set the hour or minute by pressing the † or … button.
9
When it has finished, the message Enjoy Your Watching is
displayed, and then the channel which has been stored will be
activated.
Stop
Auto Store
Channel Store in process
) button to confirm your choice.
To start the search, press the ENTER (
Result:
Enter
The Area menu is displayed.
Select your Area by pressing the † or … button.
7
Start
The message Antenna Input Check is displayed.
5
Result:
Asia/W.Europe
CIS/E.Europe
China
Hong Kong/UK
Australia
NZL/Indonesia
South Africa
▼ More
) button to confirm your choice.
Make sure that the antenna is connected to the TV, and then
press the ENTER (
) button.
Result:
Antenna Input Check
Area
The message Plug & Play is displayed, and then
the Language menu is automatically displayed a few
seconds later.
Select the appropriate language by pressing the † or … button.
4
Enter
) button
2
Enter
Plug & Play
Adjust
If the television is in Standby mode, press the POWER (
on the remote control.
BN68-00742A-00Eng_0621
2004.6.21
3:51 PM
Page 17
Plug & Play Feature (continued)
ENG
If you want to reset this feature...
1
2
TV
Press the MENU button.
The main menu is displayed.
Result:
Press the † or … button to select Setup.
The options available in the Setup group are displayed.
Result:
3
Press the ENTER (
4
Press the † or … button to select Miscellaneous.
Press the ENTER (
) button.
The options available in the Miscellaneous group are
Result:
displayed.
5
6
) button.
√
Language
: English
√
Digital NR
: On
√
Miscellaneous
√
PC Setup
√
Colour Weakness: Off
√
Burn Protection
√
Move
Enter
TV
Return
Miscellaneous
Melody
Press the † or … button to select Plug & Play.
Press the ENTER (
) button.
Result:
Setup
Time
: On
Blue Screen
√
√
Plug & Play
: Off
√
The message Plug & Play is displayed.
For further details on how to set, refer to the opposite page.
Move
Enter
Return
Choosing Your Language
When you start using your television for the first time, you must
select the language which will be used for displaying menus and
indications.
1
2
Setup
√
Time
Press the MENU button.
The main menu is displayed.
Result:
Press the † or … button to select Setup.
The options available in the Setup group are displayed.
Result:
Language
: English
√
Digital NR
: On
√
Miscellaneous
√
PC Setup
√
Colour Weakness: Off
√
Burn Protection
√
Move
3
Press the ENTER (
4
Press the † or … button to select Language.
Press the ENTER (
) button.
The languages available are listed.
Result:
5
TV
Enter
Return
) button.
TV
Select the appropriate language by pressing the † or … button.
6
Press the ENTER (
7
When you are satisfied with your choice, press the EXIT/TV (
button to return to normal viewing.
Setup
Time
Language
: English
Digital NR
: On
√
√
Miscellaneous
PC Setup
) button to confirm your choice.
Colour Weakness: Off
)
√
Burn Protection
Move
Enter
17
Return
BN68-00742A-00Eng_0621
2004.6.21
3:51 PM
Page 18
Storing Channels Automatically
ENG
TV
Channel
: Asia/W.Europe √
Area
Auto Store
√
Manual Store
√
Edit
√
Fine Tune
√
Ch. Scan
√
You can scan for the frequency ranges available to you, (availability
depends on your country). Automatically allocated programme
numbers may not correspond to actual or desired programme
numbers. However you can sort numbers manually and clear any
channels you do not wish to watch.
1
Press the MENU button.
Result:
Move
Enter
2
TV
Press the † or … button to select Channel.
Result:
Channel
Area
: Asia/W.Europe
Auto Store
CIS/E.Europe
Manual Store
Edit
Hong Kong/UK
3
Press the ENTER (
4
Press the † or … button to select Area.
Press the ENTER (
) button.
Australia
NZL/Indonesia
Result:
†
Move
Enter
TV
Return
Channel
: Asia/W.Europe √
Area
Auto Store
√
Manual Store
√
Edit
√
Fine Tune
√
Ch. Scan
√
Move
Enter
6
Press the ENTER (
7
Press the † or … button to select Auto Store.
Press the ENTER (
) button.
Result:
8
➢
➢
Return
◆
◆
◆
◆
◆
Sort
Prog.
✽
✽
✽
✽
✽
Move
Enter
Return
) button to start the search.
The search will end automatically. Channels are sorted
and stored in an order which reflects their position in
the frequency range, (with lowest first and highest last).
When it has finished, the Channel Sort menu is
displayed.
To stop the search before it has finished, press the
MENU (
) button.
When the channels have been stored, you can:
Sort them in the order required (see page 22)
Clear a channel (see page 21)
Fine-tune channel reception if necessary (see page 31)
Assign a name to the stored channels (see page 23)
Activate/deactivate the Digital Noise Reduction feature
(see page 45)
9
Select the channel that you wish to move by pressing the † or …
button. Press the ENTER (
) button.
10
Select the number of the programme to which the channel is to
be moved by pressing the † or … button.
Press the ENTER (
) button.
Result:
11
18
) button to confirm your choice.
The Auto Store menu is displayed.
Press the ENTER (
Result:
Return
Stop
2----3----4----5----6-----
The countries available are listed.
Select your country (or area) by pressing the † or … button.
57 MHz
1%
TV
) button.
5
Auto Store
Channel Store in process
Enter
The options available in the Channel group are
displayed.
China
Fine Tune
Ch. Scan
The main menu is displayed.
Return
The channel is moved to its new position and
all other channels are shifted accordingly.
Repeat Steps 8 to 9 until you have moved all the channels to
the required programme numbers.
BN68-00742A-00Eng_0621
2004.6.21
3:51 PM
Page 19
Storing Channels Manually
ENG
You can store up to 100 television channels, including those
received via cable networks.
TV
Channel
: Asia/W.Europe √
Area
When storing channels manually, you can choose:
◆ Whether or not to store each of the channels found.
◆ The programme number of each stored channel which
you wish to identify.
Auto Store
√
Manual Store
√
Edit
√
Fine Tune
√
Ch. Scan
√
Move
1
Result:
2
Enter
Return
Press the MENU button.
The main menu is displayed.
Press the † or … button to select Channel.
Result:
The options available in the Channel group are
displayed.
3
Press the ENTER (
4
Press the † or … button to select Manual Store.
Press the ENTER (
) button.
) button.
Manual Store
Prog.
Colour
System
Sound
System
9
Auto
BG
Channel
Search
Store
C --
245MHz
?
Adjust
Return
√ Move
Manual Store
Result:
5
6
The option available in the Manual Store group are
displayed with Prog. is selected.
To assign a programme number to a channel, find the correct
number by pressing the † or … button.
If necessary, select the broadcasting standard required.
Press the œ or √ button to select Colour System and
press the † or … button. The colour standards are displayed
in the following order. (depending on the model.)
Auto - PAL - SECAM or
Auto - NT3.58 - NT4.43 - PAL60
7
Press the œ or √ button to select Sound System and
press the † or … button. The sound standards are displayed
in the following order. (depending on the model.)
Prog.
Colour
System
Sound
System
9
Auto
BG
Channel
Search
Store
C --
245MHz
?
Adjust
Return
œ √ Move
Manual Store
Prog.
Colour
System
Sound
System
9
Auto
BG
Channel
Search
Store
C --
245MHz
?
Adjust
Return
œ √ Move
BG - DK - I - M
19
BN68-00742A-00Eng_0621
2004.6.21
3:51 PM
Page 20
Storing Channels Manually (continued)
ENG
8
Manual Store
Prog.
Colour
System
Sound
System
9
Auto
BG
Channel
Search
Store
C --
245MHz
?
Adjust
Return
œ √ Move
◆ Press the œ or √ button to select Channel.
◆ Press the † or … button to select C (Air channel) or
S (Cable channel).
◆ Press the √ button.
◆ Press the numeric buttons (0~9), † or … button to select
indicate the required number.
Manual Store
Prog.
Colour
System
9
Auto
BG
Search
Store
C 04
62MHz
?
œ √ Move
Adjust
➢
Sound
System
Channel
If you know the number of the channel to be stored, see the
following steps.
9
Return
If no sound or abnormal sound, re-select the sound
standard required.
If you do not know the channel numbers, select the Search by
pressing the œ or √ button. Press the † or … button to start the
search.
Result:
The tuner scans the frequency range until the first
channel or the channel that you selected is received
on your screen.
Manual Store
Prog.
Colour
System
Sound
System
9
Auto
BG
Channel
Search
Store
C 04
67MHz
?
œ √ Move
Adjust
10
To assign a programme number to a channel, select the Prog.
by pressing the œ or √ button.
Press the † or … button until you find the correct number.
11
To store the channel and associated programme number,
select the Store by pressing the œ or √ button.
Press the ENTER (
) button.
12
Repeat Steps 8 to 11 for each channel to be stored.
Return
Manual Store
Prog.
Colour
System
Sound
System
9
Auto
BG
Channel
Search
Store
C 15
245MHz
OK
œ √ Move
Enter
Return
☛
Channel mode
◆ C (Real channel mode):
You can select a channel by entering the assigned number
to each air broadcasting station in this mode.
◆ S (Cable channel mode):
You can select a channel by entering the assigned number
for each cable channel in this mode.
20
BN68-00742A-00Eng_0621
2004.6.21
3:51 PM
Page 21
Skipping Unwanted Channels
ENG
◆ Skipping unwanted channels
You can exclude the channels of your choice from the channel
scan operation. When you scan through the stored channels,
those that you have chosen to skip are thus not displayed.
All channels that you do not specifically choose to skip are
displayed during scanning.
1
Channel
: Asia/W.Europe √
Area
Auto Store
√
Manual Store
√
Edit
√
Fine Tune
√
Ch. Scan
√
Press the MENU button.
Result:
2
TV
Press the † or … button to select Channel.
Result:
Move
The main menu is displayed.
Enter
TV
The options available in the Channel group are
displayed.
Edit
√
Add/Delete
√
Sort
LNA
3
4
Press the ENTER (
) button.
√
: Off
Name
√
Child Lock
√
Press the † or … button to select Edit.
Press the ENTER (
) button.
Result:
5
Return
Press the † or … button to select Add/Delete.
Press the ENTER (
) button.
Result:
Move
The Edit menu is displayed.
TV
The Add/Delete menu is displayed with the current
channel automatically is selected.
6
Press the † or … button to select the channel to be deleted.
Press the ENTER (
) button.
7
To add or delete the channel, select Added or Deleted by
pressing the † or … button.
Press the ENTER (
) button to confirm.
Enter
Return
Add/Delete
Prog.
1
2
3
4
5
---------------------
✽
✽
✽
✽
✽
Move
TV
Added
Deleted
Deleted
Deleted
Deleted
Enter
Return
Add/Delete
Prog.
1
2
3
4
5
---------------------
✽
✽
✽
✽
✽
Adjust
Added
Deleted
Deleted
Deleted
Deleted
Enter
21
Return
BN68-00742A-00Eng_0621
2004.6.21
3:51 PM
Page 22
Sorting the Stored Channels
ENG
TV
This operation allows you to change the programme numbers of
stored channels. This operation may be necessary after using ATM.
You can delete those channels you do not want to keep.
Channel
: Asia/W.Europe √
Area
Auto Store
√
Manual Store
√
Edit
√
Fine Tune
√
Ch. Scan
√
1
Result:
2
Move
Enter
TV
Return
Edit
√
Add/Delete
√
Sort
LNA
√
: Off
Name
√
Child Lock
√
Enter
Press the ENTER (
4
Press the † or … button to select Edit.
Press the ENTER (
) button.
Result:
Return
Sort
✽
✽
✽
✽
✽
Enter
7
Select the number of the programme to which the channel is to
be moved by pressing the † or … button.
Press the ENTER (
) button.
Return
Sort
Prog.
2 ----3 ----4 ----5 ----6 -----
✽
✽
✽
✽
✽
Move
-----
Enter
22
✽
Return
The Sort menu is displayed.
Select the channel that you wish to move by pressing the † or …
button. Press the ENTER (
) button.
8
TV
The Edit menu is displayed.
Press the † or … button to select Sort.
Press the ENTER (
) button.
Result:
Move
) button.
6
Prog.
2 ----3 ----4 ----5 ----6 -----
The options available in the Channel group are
displayed.
3
Result:
TV
The main menu is displayed.
Press the † or … button to select Channel.
Result:
5
Move
Press the MENU button.
The channel is moved to its new position and
all other channels are shifted accordingly.
Repeat Steps 6 to 7 until you have moved all the channels to
the required programme numbers.
BN68-00742A-00Eng_0621
2004.6.21
3:51 PM
Page 23
Assigning Names to Channels
ENG
Channel names will be assigned automatically when channel
information is broadcast. These names can be changed, allowing
you to assign new names.
1
The main menu is displayed.
Auto Store
√
Manual Store
√
Edit
√
Fine Tune
√
Ch. Scan
√
Press the † or … button to select Channel.
Result:
3
Channel
: Asia/W.Europe √
Area
Press the MENU button.
Result:
2
TV
Move
The options available in the Channel group are
displayed.
Press the ENTER (
) button.
Enter
TV
Return
Edit
√
Add/Delete
4
5
Sort
Name
√
Result:
Child Lock
√
8
The Edit menu is displayed.
The Name menu is displayed with the current channel
automatically is selected.
Return
Name
Prog.
2
3
4
5
6
Press the † or … button to select a letter (A~Z), a number (0~9)
or a symbol (-, space). Move on the previous or next letter by
pressing the œ or √ button.
When you have finished entering the name,
press the ENTER (
) button to confirm the name.
Enter
TV
Arrow indications are displayed around the name box.
√
: Off
Move
If necessary, select the channel to be assigned a new name by
pressing the † or … button.
Press the ENTER (
) button.
Result:
7
LNA
Press the † or … button to select Name.
Press the ENTER (
) button.
Result:
6
√
Press the † or … button to select Edit.
Press the ENTER (
) button.
Name
✽
✽
✽
✽
✽
---------------------
Move
Enter
TV
Return
Name
Prog.
2
3
4
5
6
Name
✽
✽
----✽
✽
---------------------
Adjust
Move
23
Return
BN68-00742A-00Eng_0621
2004.6.21
3:51 PM
Page 24
Using the LNA (Low Noise Amplifier) Feature
ENG
TV
Channel
: Asia/W.Europe √
Area
Auto Store
√
Manual Store
√
Edit
√
Fine Tune
√
Ch. Scan
√
This function is very useful in the situation that the TV is used in
weak signal. LNA amplifies the TV signal in the weak signal area,
but not noise.
1
Press the MENU button.
Result:
Press the † or … button to select Channel.
2
Move
Enter
TV
Return
Edit
√
Add/Delete
√
Sort
LNA
√
: Off
Name
√
Child Lock
√
Result:
Enter
Press the ENTER (
4
Press the † or … button to select Edit.
Press the ENTER (
) button.
Result:
Edit
) button.
The Edit menu is displayed.
Press the † or … button to select LNA.
Press the ENTER (
) button.
Return
Result:
TV
The options available in the Channel group are
displayed.
3
5
Move
The main menu is displayed.
The options available are listed.
Select On or Off by pressing the † or … button.
Press the ENTER (
) button to confirm.
6
Add/Delete
Sort
LNA
:
Name
Off
➢
On
Child Lock
◆ If the picture is noisy with the LNA set to On, select Off.
◆ LNA setting is to be made for each channel.
Move
Enter
24
Return
BN68-00742A-00Eng_0621
2004.6.21
3:51 PM
Page 25
Activating the Child Lock
ENG
◆ Activating the child lock
This feature allows you to lock the television so that it cannot be
switched on via the front panel. It can, however, still be switched
on via the remote control. Thus, by keeping the remote control
away from unauthorised users, such as children, you can prevent
them from watching unsuitable programme.
1
Channel
: Asia/W.Europe √
Area
Auto Store
√
Manual Store
√
Edit
√
Fine Tune
√
Ch. Scan
√
Press the MENU button.
Result:
2
TV
Press the † or … button to select Channel.
Result:
Move
The main menu is displayed.
Enter
TV
The options available in the Channel group are
displayed.
Edit
√
Add/Delete
√
Sort
LNA
3
4
Press the ENTER (
) button.
√
: Off
Name
√
Child Lock
√
Press the † or … button to select Edit.
Press the ENTER (
) button.
Result:
5
Return
Press the † or … button to select Child Lock.
Press the ENTER (
) button.
Result:
Move
The Edit menu is displayed.
6
Press the † or … button to select the channel to be locked.
7
Press the ENTER ( ) button.
To lock the channel, select Locked by pressing the † or … button
(to unlock the channel, select Unlocked).
Press the ENTER ( ) button to confirm.
Return
Child Lock
TV
The Child Lock menu is displayed with the current
channel automatically is selected.
Blue Screen is displayed when the Child Lock is
activated.
Enter
Prog.
2
3
4
5
6
✽
✽
✽
✽
✽
---------------------
Move
Unlocked
Unlocked
Unlocked
Unlocked
Unlocked
Enter
Return
Child Lock
TV
Prog.
2
3
4
5
6
✽
✽
✽
✽
✽
---------------------
Adjust
Unlocked
Unlocked
Unlocked
Unlocked
Unlocked
Enter
25
Return
BN68-00742A-00Eng_0621
2004.6.21
3:51 PM
Page 26
Displaying Information
ENG
You can view the channel information and setting status you select
by pressing the “INFO (
)” button on the remote control.
Mono
P1 ✽
Picture
: Dynamic
Sound
: Music
09 : 17 am
Changing the Picture Standard
TV
You can select the type of picture which best corresponds to your
viewing requirements.
Picture
Mode
Custom
Colour Tone
Colour Control
Film Mode
Size
PIP
† More
Move
: Normal
: Off
: 16 : 9
Enter
TV
√
√
√
√
√
√
√
: Dynamic
1
Press the MENU button.
The main menu is displayed.
Result:
2
Press the † or … button to select Picture.
The options available in the Picture group are
Result:
displayed.
3
Press the ENTER (
) button.
The Mode is selected.
Result:
4
Press the ENTER (
) button again.
The options available are listed.
Result:
5
Select the option by pressing the † or … button.
The following modes are available depending on the
Result:
input source.
◆ Dynamic - Standard - Movie - Custom
◆ High - Middle - Low - Custom
(PC or DVI Mode).
6
Press the ENTER (
Return
Picture
Mode
Custom
Colour Tone
Colour Control
Film Mode
Size
PIP
† More
Move
: Dynamic
Dynamic
Standard
: Normal
Movie
: Off Custom
: 16 : 9
Enter
Return
➢
26
) button to confirm.
You can also set these options simply by pressing the
P.MODE (
: Picture Mode) button.
BN68-00742A-00Eng_0621
2004.6.21
3:51 PM
Page 27
Adjusting the Picture Settings
ENG
Your television has several settings which allow you to control
picture quality.
1
TV
Press the MENU button.
Result:
The main menu is displayed.
Press the † or … button to select Picture.
2
Result:
The options available in the Picture group are
displayed.
3
Press the ENTER (
4
Select the required option (Custom, Colour Tone) pressing
the † or … button.
5
Press the † or … button to select Custom.
Press the ENTER (
) button.
Result:
6
Move
) button.
➢
➢
➢
: Off
: 16 : 9
Return
Custom
100
45
75
55
R 50
The Custom menu is displayed.
Move
Enter
Return
Contrast
100
Custom Options available in PC, DVI Mode: Contrast,
Brightness, Sharpness.
The horizontal bar is displayed. Move the horizontal bar’s
cursor left or right by pressing the œ or √ button.
TV
When the picture mode is set to Custom, the settings values
may vary depending on the input source.
(ex. RF, Video, Component, PC or DVI)
If you make any changes to these settings, the picture
standard is automatically switched to the Custom.
When you are satisfied with the settings, press the EXIT/TV (
button to return to normal viewing.
➢
: Normal
Contrast
Brightness
Sharpness
Colour
Tint
G 50
◆ Colour Tone : Cool 2, Cool 1, Normal, Warm 1, Warm 2.
7
√
√
√
√
√
√
√
: Dynamic
Enter
TV
Press the ENTER (
) button to change the setting.
The options are displayed in the following order.
◆ Custom : Contrast, Brightness, Sharpness, Colour,
Tint(NTSC ONLY)
➢
Picture
Mode
Custom
Colour Tone
Colour Control
Film Mode
Size
PIP
† More
Picture
Mode
Custom
Colour Tone
Colour Control
Film Mode
Size
PIP
† More
Move
: Dynamic
: Normal
Cool 2
Cool 1
: Off
Normal
: 16 : 9
Warm 1
Warm 2
Enter
)
If you make any changes to these settings, the picture
standard is automatically switched to the Custom.
27
Return
BN68-00742A-00Eng_0621
2004.6.21
3:51 PM
Page 28
Adjusting the Picture Settings (PC or DVI Mode)
➢
ENG
Preset to the PC or DVI mode by using the SOURCE button.
1
TV
Press the MENU button.
Picture
Mode
Custom
Colour Tone
Colour Control
Film Mode
Size
PIP
† More
Move
: Custom
: Off
: 16 : 9
Enter
TV
√
√
√
√
√
√
√
: High
Result:
Press the † or … button to select Picture.
2
Result:
3
Press the ENTER (
4
Press the † or … button to select Custom.
Press the ENTER (
) button.
Result:
Contrast
Brightness
Sharpness
Colour
Tint
G 50
70
50
70
50
R 50
) button.
Enter
The Custom menu is displayed.
Press the † or … button to select the option (Contrast,
Brightness, Sharpness) to be adjusted.
Press the ENTER (
) button.
5
Result:
TV
The options available in the Picture group are
displayed.
Return
Custom
Move
The main menu is displayed.
Return
The horizontal bar is displayed.
Move the horizontal bar’s cursor left or right by
pressing the œ or √ button.
6
Press the MENU button to confirm your choice.
7
Press the MENU button.
Picture
Mode
Custom
Colour Tone
Colour Control
Film Mode
Size
PIP
† More
Move
TV
: High
Result:
Custom
: Normal
Colour1
: Off
: 16 :Colour2
9
Colour3
Enter
Return
8
Press the † or … button to select Colour Tone.
Press the ENTER (
) button.
9
Select the option by pressing the † or … button.
The colour tones are displayed in the following order.
Custom (PC mode only) - Colour1 - Colour2 - Colour3
Colour Control
R
G
B
70
50
70
10
Enter
Press the MENU button.
Result:
11
Move
Return
The Colour Control menu is displayed.
Press the † or … button to select the option (R, G, B) to be
adjusted. Press the ENTER (
) button.
Result:
➢
The options available in the Picture group are
displayed again.
Press the † or … button to select Colour Control.
Press the ENTER (
) button.
Result:
12
28
The options available in the Picture group are
displayed again.
The horizontal bar is displayed.
Move the horizontal bar’s cursor left or right by
pressing the œ or √ button.
The Colour Control is not available in the DVI Mode.
BN68-00742A-00Eng_0621
2004.6.21
3:51 PM
Page 29
Setting the Picture (PC Mode)
➢
1
Preset to the PC mode by using the SOURCE button.
ENG
Press the MENU button.
TV
Result:
2
The main menu is displayed.
Press the † or … button to select Setup.
Result:
The options available in the Setup group are
displayed.
3
Press the ENTER (
4
Press the † or … button to select PC Setup.
Press the ENTER (
) button.
Setup
√
Time
) button.
Language
: English
√
Digital NR
: On
√
Miscellaneous
√
PC Setup
√
Colour Weakness: Off
√
Burn Protection
√
Move
Result:
5
TV
The options available in the PC Setup group are
displayed.
Press the † or … button to select Image Lock.
Press the ENTER (
) button.
Result:
Enter
PC Setup
Image Lock
√
Position
√
Information
√
Auto Adjustment
√
The options available in the Image Lock group are
displayed.
Move
6
Press the † or … button to select the option (Coarse, Fine) to be
adjusted. Press the ENTER (
) button.
Result:
Press the MENU (
) button to confirm your choice.
8
Press the MENU (
) button.
9
Result:
10
11
The options available in the PC Setup group are
displayed again.
Press the † or … button to select Position.
Press the ENTER (
) button.
Enter
TV
The horizontal bar is displayed. Move the horizontal
bar’s cursor left or right by pressing the œ or √ button.
7
Result:
Return
Return
Image Lock
Coarse
50
Fine
20
Move
Enter
Coarse
Return
50
The options available in the Position group are
displayed.
Adjust the position by using the †, …, œ, or √ button.
Press the MENU (
TV
) button to confirm your choice.
PC Setup
Image Lock
√
Position
√
Information
√
Auto Adjustment
√
Move
Enter
TV
Return
Position
Move
œ √ Move
29
Return
BN68-00742A-00Eng_0621
2004.6.21
3:51 PM
Page 30
Setting the Picture (PC Mode)
➢
ENG
12
TV
PC Setup
Image Lock
√
Position
√
Information
√
Auto Adjustment
√
Preset to the PC mode by using the SOURCE button.
If you get the PC information, select the Information by
pressing the † or … button.
Press the ENTER (
) button.
Result:
13
Enter
Return
14
TV
Information
800 ✻ 600
H-Frequency
:
38.0KHz
V-Frequency
:
60.5Hz
15
Return
TV
PC Setup
Image Lock
√
Position
√
Information
√
Auto Adjustment
√
Move
TV
Enter
Return
Auto Adjustment
Auto Adjusting
30
The options available in the PC Setup group are
displayed again.
Press the † or … button to select Auto Adjustment.
Press the ENTER (
) button.
Result:
:
Resolution
The resolution, horizontal and vertical frequency are
displayed.
Press the MENU button.
Result:
Move
(continued)
The screen quality and position are automatically reset
with the Auto Adjusting displayed.
When you are satisfied with the settings, press the MENU (
button repeatedly to return to the normal viewing.
)
BN68-00742A-00Eng_0621
2004.6.21
3:51 PM
Page 31
Using the Fine Tune
ENG
If reception is weak, you can fine tune a channel manually.
TV
1
Press the MENU button.
Result:
The main menu is displayed.
Press the † or … button to select Channel.
2
Result:
The options available in the Channel group are
displayed.
3
Press the ENTER (
4
Press the † or … button to select Fine Tune.
Press the ENTER (
) button.
Channel
: Asia/W.Europe √
Area
Auto Store
√
Manual Store
√
Edit
√
Fine Tune
√
Ch. Scan
√
Move
Enter
Return
) button.
Fine Tune
P1
0
Result:
The horizontal bar is displayed. Move the horizontal
bar’s cursor left or right by pressing the œ or √ button
to reach the required setting.
Reset
Move
Press the œ or √ button until the picture and sound are both
clear and sharp. Press the ENTER (
) button.
5
Return
œ √ Adjust
Store
Fine Tune
P1
To reset the fine tuning to 0, select Reset by pressing the † or …
button then press the ENTER (
) button.
6
3
Reset
Move
➢
➢
Return
œ √ Adjust
Store
If you are unable to fine tune a channel, check that the
Colour System and Sound System settings are correct.
Fine Tune
Fine tune Store will change the colour of the Channel
OSD(On Screen Display) from White to Red.
P 1 is Fine Tuned
3
Reset
Move
P1
Return
œ √ Adjust
C11
31
Store
BN68-00742A-00Eng_0621
2004.6.21
3:51 PM
Page 32
Viewing the Channel Scan Picture
ENG
TV
1
Channel
Press the MENU button.
Result:
: Asia/W.Europe √
Area
Auto Store
√
Manual Store
√
Edit
√
Fine Tune
√
Ch. Scan
√
Move
Enter
Return
The main menu is displayed.
Press the † or … button to select Channel.
2
Result:
The options available in the Channel group are
displayed.
3
Press the ENTER (
4
Press the † or … button to select Ch. Scan.
Press the ENTER (
) button.
) button.
Ch. Scan
Result:
P1
✽
5
You can view every memorized channel in order.
Press the MENU (
) button to exit.
Return
➢
When PIP ON is activated, the PIP will appear in
Large mode and PIP channel will be scanned.
Freezing the Current Picture
You can freeze the picture when watching a television programme
simply by pressing the “STILL” button. To return to normal viewing,
press it again.
➢
➢
32
In the PIP mode, the main and sub pictures are stilled at
the same time.
This function will automatically cancel after 5 minutes.
BN68-00742A-00Eng_0621
2004.6.21
3:51 PM
Page 33
Selecting the Picture Size
ENG
You can select the picture size which best corresponds to your
viewing requirements.
1
TV
Press the MENU button.
Result:
The main menu is displayed.
Press the † or … button to select Picture.
2
Result:
Picture
Mode
Custom
Colour Tone
Colour Control
Film Mode
Size
PIP
† More
The options available in the Picture group are
displayed.
Move
3
Press the ENTER (
4
Press the † or … button until the Size is selected.
Press the ENTER (
) button
16 : 9
Press the † or … button to change the setting.
14 : 9
) button.
: Dynamic
: Normal
: Off
: 16 : 9
Enter
TV
√
√
√
√
√
√
√
Return
Size
Panorama
.
5
◆ 16:9
: Sets the picture to 16:9 wide mode.
◆ Panorama : Use this mode for the wide aspect ratio of a
panoramic picture.
◆ Zoom
: Magnify the size of the picture vertically on
screen.
◆ 14:9
: Magnify the size of the picture more than 4:3.
◆ 4:3
: Sets the picture to 4:3 normal mode.
6
Press the ENTER (
) button to confirm.
Zoom
4:3
Move
Enter
Return
PC to DVI Mode
TV
Size
16 : 9
Panorama
Zoom
14 : 9
4:3
➢
◆ You can select these options by simply pressing the
P.SIZE button on the remote control.
◆ The picture size can not be changed in the PIP mode.
Move
Enter
◆ Depending on the input source, the P.SIZE options
may vary.
Positioning and Sizing the screen using Zoom
➢
◆ Resizing the screen using the Zoom enables the
positioning and sizing of the screen to up/down
direction using the † or … button as well as the
screen size.
◆ Move the screen up/down using the † or … button
after selecting the
by pressing the † or … button.
◆ Resize the screen vertically using the † or … button
after selecting the
by pressing the † or … button.
◆ Screen enlargement operates only in TV/Video/
S-Video/Component1, 2 input modes.
◆ PC/DVI modes prevents the screen enlargement
function.
33
Return
BN68-00742A-00Eng_0621
2004.6.21
3:52 PM
Page 34
Selecting the Film Mode
ENG
TV
You can automatically sense and process film signals from some
sources and adjust the picture for optimum quality.
Picture
Mode
Custom
Colour Tone
Colour Control
Film Mode
Size
PIP
† More
Move
: Dynamic
: Normal
: Off
: 16 : 9
Enter
TV
√
√
√
√
√
√
√
Move
Press the MENU button.
The main menu is displayed.
Result:
2
Press the † or … button to select Picture.
The options available in the Picture group are
Result:
displayed.
3
Press the ENTER (
4
Press the † or … button to select Film Mode.
Press the ENTER (
) button.
5
Press the † or … button to change the setting. (Off or On.)
Return
Picture
Mode
Custom
Colour Tone
Colour Control
Film Mode
Size
PIP
† More
1
: Dynamic
: Normal
: Off Off
: 16 :On
9
Enter
◆ Off : Switches off the Film Mode.
◆ On : Automatically senses and processes film signals from
some sources and adjusts the picture for optimum
quality.
Return
6
Press the ENTER (
➢
34
) button.
) button to confirm.
◆ Not available in the PC, Component (480P, 576P, 720P,
1080i) or DVI modes.
◆ Mode discrepancies, such as turning off Film Mode while
viewing a film source or turning on Film Mode while viewing
non-film sources, may affect the picture quality.
BN68-00742A-00Eng_0621
2004.6.21
3:52 PM
Page 35
DNIeTM (Digital Natural Image engine)
ENG
This feature bring you more detailed image with 3D noise reduction, detail
enhancement, contrast enhancement and white enhancement. New image
compensation Algorithm gives brighter, clearer, much detailed image to you.
DNIeTM technology will fit every signals into your eyes.
1
TV
Press the MENU button.
Result:
The main menu is displayed.
Move
Press the † or … button until the Picture is selected.
2
Result:
The options available in the Picture group are
displayed.
3
Press the ENTER (
4
Press the † or … button until the DNIe is selected.
Press the ENTER (
) button.
5
Press the † or … button to change the setting.
◆ On
: Switches on the DNIe mode.
◆ Off
: Switches off the DNIe mode.
◆ Demo (Option) : The screen before applying DNIe appears on
the right and the screen after applying DNIe
appears on the left.
) button.
Picture
Mode
Custom
Colour Tone
Colour Control
Film Mode
Size
PIP
† More
: Dynamic
: Normal
: Off
: 16 : 9
Enter
TV
√
√
√
√
√
√
√
Return
Picture
… More
DNIe
: On On
My Colour Control
Off
Demo
➢
Move
Enter
You can also set these options simply by pressing the
DNIe button.
35
Return
BN68-00742A-00Eng_0621
1904.1.7
10:9 PM
Page 36
Setting the My Colour Control Mode
ENG
Using the My Colour Control Function in the Easy Control Menu
➢
➢
TV
Picture
Mode
Custom
Colour Tone
Colour Control
Film Mode
Size
PIP
† More
Move
TV
√
√
√
√
√
√
√
: Dynamic
: Normal
: Off
: 16 : 9
Enter
Return
Move
√
: Custom
Enter
Skin, sky and grass tones are easily adjustable to suit
your preferences.
1
Press the MENU button.
The main menu is displayed.
Result:
2
Press the † or … button to select Picture.
The options available in the Picture group are
Result:
displayed.
3
Press the ENTER (
4
Press the † or … button to select My Colour Control.
Press the ENTER (
) button.
5
Press the † or … button to select Easy Control.
Press the ENTER (
) button.
The options available in the Easy Control
Result:
group are displayed.
6
Press the œ or √ button to select among the various picture
settings.
My Colour Control
Easy Control
Detail Control
My Colour Control mode allows users to adjust colours to
according to their preferences, by adjusting skin, sky,
and grass tones using the predefined settings (Standard,
Custom, Blue, Green, Pink) without affecting other
colours on the screen.
Return
) button.
◆ The original picture (before adjustment) is shown on the left
side, while the selected mode is shown on the right side.
◆ There are five Easy Control modes:
Blue, Green, Pink, Standard, and Custom.
Original
Blue
◆ Blue
Green
Pink
Standard
Custom
Easy Control
Blue
Move
Green
Enter
Pink
√
Return
7
☛
: Emphasizing Clear Blues. Feel the clear
sun shine on the blue Mediterranean sea.
: Emphasizing Mild Greens. Feel the translucent,
romantic turquoise sea.
: Emphasizes warm skin colours.
: Standard Picture.
: Changing the settings in the Detail Control
menu will automatically set to Custom
(see next page).
Press the ENTER (
) button to confirm.
◆ Images shown above may differ from the actual adjustment
on the screen. These images are presented for illustrative
purposes.
◆ This feature is operated when the “DNIe” is set to “On” or
“Demo” mode.
36
BN68-00742A-00Eng_0621
2004.6.21
3:52 PM
Page 37
Setting the My Colour Control Mode (continued)
ENG
My Colour Control Custom Settings
➢
1
Users can adjust the detail colour control (Pink, Green,
and Blue).
Press the MENU button.
The main menu is displayed.
Result:
TV
Picture
Mode
Custom
Colour Tone
Colour Control
Film Mode
Size
PIP
† More
Press the † or … button to select Picture.
The options available in the Picture group are
Result:
displayed.
2
3
Press the ENTER (
4
Press the † or … button to select My Colour Control.
Press the ENTER (
) button.
) button.
5
Press the † or … button to select Detail Control.
Press the ENTER (
) button.
The options available in the Detail Control
Result:
group are displayed.
6
Press the † or … button to select the desired colour and then
press the ENTER (
) or √ button.
Move
TV
√
√
√
√
√
√
√
: Dynamic
: Normal
: Off
: 16 : 9
Enter
Return
My Colour Control
Easy Control
Detail Control
Move
√
: Custom
Enter
Return
Press the œ or √ button to adjust the setting.
7
TV
☛
Detail Control
◆ The original picture (before adjustment) is shown on the
left side, while the picture after adjustment is shown on
the right side, and an adjustment bar on the bottom of
the screen.
Pink
Green
Blue
Reset
50
50
50
◆ This feature is operated when the “DNIe” is set to “On” or
“Demo” mode.
Move
Enter
Original
Return
Adjusted
Detail Control
Pink
Move
50
Adjust
37
Return
BN68-00742A-00Eng_0621
2004.6.22
11:15 PM
Page 38
Setting the My Colour Control Mode (continued)
ENG
Resetting the My Colour Control to the Factory Defaults
➢
TV
Picture
Mode
Custom
Colour Tone
Colour Control
Film Mode
Size
PIP
† More
Move
TV
√
√
√
√
√
√
√
: Dynamic
: Normal
: Off
: 16 : 9
Enter
Return
1
Press the MENU button.
The main menu is displayed.
Result:
2
Press the † or … button to select Picture.
The options available in the Picture group are
Result:
displayed.
3
Press the ENTER (
4
Press the † or … button to select My Colour Control.
Press the ENTER (
) button.
5
Press the † or … button to select Detail Control.
Press the ENTER (
) button.
The options available in the Detail Control
Result:
group are displayed.
6
Press the † or … button to select Reset.
Press the ENTER (
) button.
My Colour Control
Easy Control
Detail Control
Move
: Custom
Enter
To return to the factory default settings for My Colour
Control colours, use the Reset function.
√
Return
➢
TV
Detail Control
Pink
Green
Blue
Reset
50
50
50
Move
TV
Enter
Return
Detail Control
Pink
Green
Blue
Reset
50
50
50
Move
Enter
38
) button.
Return
☛
The previously adjusted My Colour Control will be reset to
the factory defaults.
◆ This feature is operated when the “DNIe” is set to “On” or
“Demo” mode.
BN68-00742A-00Eng_0621
2004.6.21
3:52 PM
Page 39
Using the Colour Weakness Enhancement Option
ENG
This option adjusts the Red, Green or Blue colour to enhance
the image according to the user's particular colour weakness.
1
2
Press the MENU button.
The main menu is displayed.
Result:
Press the ENTER (
4
Press the † or … button to select Colour Weakness.
Press the ENTER (
) button.
The options available in the Colour Weakness
Result:
group are displayed.
) button.
Press the ENTER ( ) button again.
Press the † or … button to select On, then press the
ENTER (
) button.
6
Press the † or … button to select the colour you wish to adjust,
then press the ENTER ( ) button.
7
Press the œ or √ button to adjust to your preference.
) or ENTER (
√
Language
: English
√
Digital NR
: On
√
Miscellaneous
√
PC Setup
Colour Weakness : Off
Burn Protection
√
√
√
Move
5
Press the MENU (
Setup
Time
Press the † or … button to select Setup.
The options available in the Setup group are
Result:
displayed.
3
8
TV
TV
Enter
Return
Colour Weakness
√
0
0
0
Colour Weakness : Off
Red
Green
Blue
Move
TV
Enter
Colour Weakness
Colour Weakness : On
Red
Green
Blue
) button to confirm.
Return
Move
Enter
√
0
0
0
Return
Colour Weakness
Red
Move
50
Adjust
39
Return
BN68-00742A-00Eng_0621
2004.6.21
3:52 PM
Page 40
Setting the Blue Screen
ENG
If no signal is being received or the signal is very weak, a blue screen automatically replaces the noisy picture background. If you wish to continue viewing the
poor picture, you must set the “Blue Screen“ mode to “Off“.
TV
Setup
√
Time
Language
: English
√
Digital NR
: On
√
Miscellaneous
√
PC Setup
Colour Weakness : Off
Burn Protection
√
√
√
Move
Enter
TV
Return
1
Press the MENU button.
Result:
Press the † or … button to select Setup.
2
Result:
: On
Press the ENTER (
4
Press the † or … button to select Miscellaneous.
Press the ENTER ( ) button.
Blue Screen
: Off
Move
Enter
TV
√
Result:
√
Plug & Play
√
Return
The options available in the Setup group are
displayed.
3
Miscellaneous
Melody
The main menu is displayed.
) button.
The options available in the Miscellaneous group
are displayed.
5
Press the † or … button to select Blue Screen.
Press the ENTER (
) button.
6
Press the † or … button to change the setting. (Off or On).
7
Press the ENTER (
) button to confirm.
Miscellaneous
Melody
➢
: On
Plug & Play
Blue Screen
Move
: Off Off
On
Enter
40
Return
◆ Blue Screen is displayed while no signal from the external
device in the External Mode, regardless of the Blue
Screen Setting.
BN68-00742A-00Eng_0621
2004.6.21
3:52 PM
Page 41
Setting the Melody Sound
ENG
You can hear clear melody sound when the television is powered on or off.
1
2
Press the MENU button.
The main menu is displayed.
Result:
TV
Press the † or … button to select Setup.
The options available in the Setup group are displayed.
Result:
3
Press the ENTER (
4
Press the † or … button to select Miscellaneous.
Press the ENTER ( ) button.
Result:
) button.
The options available in the Miscellaneous group
are displayed.
5
Press the † or … button to select Melody.
Press the ENTER (
) button.
6
Press the † or … button to change the setting (Off or On).
7
Press the ENTER (
Setup
√
Time
Language
: English
√
Digital NR
: On
√
Miscellaneous
√
PC Setup
Colour Weakness : Off
Burn Protection
√
√
√
Move
Enter
TV
Miscellaneous
Melody
: Off
Blue Screen
: Off
Move
Enter
TV
√
√
Plug & Play
) button to confirm.
Return
√
Return
Miscellaneous
Melody
Plug & Play
: Off Off
On
Blue Screen
: Off
Move
Enter
41
Return
BN68-00742A-00Eng_0621
2004.6.21
3:52 PM
Page 42
Viewing the Picture In Picture (PIP)
ENG
TV
You can display a sub picture within the main picture of TV program or external A/V
devices. In this way you can watch TV program or monitor the video input from any
connected devices while watching TV or other video input.
Picture
Mode
Custom
Colour Tone
Colour Control
Film Mode
Size
PIP
† More
Move
√
√
√
√
√
√
√
: Dynamic
: Normal
: Off
: 16 : 9
Enter
PIP
: On Off
: TV On
Source
Swap
Size
Position
Prog.
:
:
: P 11
Move
Press the MENU button.
The main menu is displayed.
Result:
2
Press the † or … button to select Picture.
The options available in the Picture group are
Result:
displayed.
3
Press the ENTER (
4
Press the † or … button to select PIP.
Press the ENTER (
) button.
Return
PIP
TV
1
Result:
Enter
PIP
Source
Swap
Size
Position
Prog.
: On
: TV
The options available in the PIP group are displayed.
5
Press the ENTER ( ) button again.
To activate, set the PIP to on by pressing the † or … button.
6
Press the † or … button to select Source.
Press the ENTER (
) button.
Return
PIP
TV
) button.
Result:
TV
AV1
AV2
:
AV3
:
S-Video1
: P08
S-Video2
The sources are displayed in the following order:
TV - AV1 - AV2 - AV3 - S-Video1 - S-Video2 Component1 - Component2 - PC - DVI
➢
◆ The PC can not be selected in DVI mode.
◆ The DVI can not be selected in PC mode.
†
Move
Enter
Return
PIP
TV
PIP
Source
Swap
Size
Position
Prog.
Move
: On
: TV
√
√
√
:
:
: P 11
√
√
Enter
7
Select a source of the sub picture by pressing the † or … button.
Press the ENTER (
) button.
8
Press the † or … button to select Swap.
Press the ENTER (
) button.
Result:
9
√
PIP
Source
Swap
Size
Position
Prog.
➢
10
:
:
: P08
Enter
42
The sizes are displayed in the following order:
(Large) - ( Small) - (Double1) - (Double2)
Return
: On
: TV
Move
Press the † or … button to select Size.
Result:
PIP
TV
The main picture and sub picture are interchanged.
Return
◆ The Double 1 or Double 2 mode can not be
selected in PC or DVI mode.
Select a size of the sub picture by pressing the † or … button.
Press the ENTER (
) button.
BN68-00742A-00Eng_0621
2004.6.21
3:52 PM
Page 43
Viewing the Picture In Picture (PIP) (continued)
ENG
Table of PIP Settings
Main
PIP
TV
AV1
AV2
AV3
S-Video1
S-Video2
COMP1
COMP2
PC
DVI
TV
O
O
O
O
O
O
O
O
O
O
AV1
O
X
O
O
O
O
O
O
O
O
AV2
O
O
X
O
O
O
O
O
O
O
AV3
O
O
O
X
O
O
O
O
O
O
S-Video1 S-Video2 COMP1 COMP2
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
X
O
O
O
O
X
O
O
O
O
X
X
O
O
X
X
O
O
X
X
O
O
X
X
PC
O
O
O
O
O
O
X
X
X
X
DVI
O
O
O
O
O
O
X
X
X
X
X - This PIP combination is not available.
O - This PIP combination is available.
11
Press the † or … button to select Position.
Press the ENTER (
) button.
Result:
PIP
Source
Swap
Size
Position
Prog.
The positions available are displayed.
-
12
Select a position by pressing the † or … button.
Press the ENTER (
) button.
13
Press the † or … button to select Prog..
Press the ENTER (
) button.
14
Select the channel that you want to view through sub picture
by pressing the † or … button. Press the ENTER (
) button.
PIP
TV
: On
: TV
:
:
: P08
Move
Enter
PIP
TV
➢
If the sub picture is no signal and the main picture is
output from a Component, PC or DVI signal, the sub
picture will be blue. If the main picture is output from
a Video signal, the sub picture will be black.
Return
PIP
Source
Swap
Size
Position
Prog.
: On
: TV
:
:
: P08 P 11
Move
Enter
43
Return
BN68-00742A-00Eng_0621
2004.6.21
3:52 PM
Page 44
Viewing the Picture In Picture (PIP) (continued)
ENG
Easy functions of remote control.
Buttons
Feature
PIP ON
Used to activate or deactivate the PIP function directly.
SWAP
Used to interchange the main picture and the sub
picture.
➢
44
When the main picture is in the Video mode and
the sub picture is in the TV mode, you might not
hear the sound of main picture when pressing
the SWAP (
) button after changing the sub
picture channel. At this time, reselect the channel
of main picture.
POSITION
Used to move the sub picture counterclockwise.
SOURCE
Used to assign a source of sub picture (TV, AV1, AV2,
AV3, S-Video1, S-Video2, Component1, Component2,
PC, DVI).
SIZE
Used to select a size of sub picture (Large, Small,
Double1, Double2).
SCAN
Used to scan every memorized channel in order.
To stop scanning, press it again.
P
Used to select the channel of sub picture.
/
BN68-00742A-00Eng_0621
2004.6.21
3:52 PM
Page 45
Using the Digital NR (Digital Noise Reduction) Feature
ENG
If the signal received by your television is weak, you can activate
this feature to help reduce any static and ghosting that may appear
on the screen.
1
2
Press the MENU button.
The main menu is displayed.
Result:
TV
Press the † or … button until the Setup is selected.
The options available in the Setup group are displayed.
Result:
3
Press the ENTER (
4
Press the † or … button until the Digital NR is selected.
Press the ENTER (
) button.
5
Select Off or On by pressing the † or … button.
Press the ENTER (
) button to confirm.
Setup
√
Time
) button.
Language
: English
√
Digital NR
: On
√
Miscellaneous
√
PC Setup
Colour Weakness : Off
Burn Protection
√
√
√
Move
Enter
TV
Return
Setup
Time
Language
: English
Digital NR
: On Off
Miscellaneous
On
PC Setup
Colour Weakness : Off
Burn Protection
Move
Enter
45
Return
BN68-00742A-00Eng_0621
2004.6.21
3:52 PM
Page 46
Protecting the Screen Burning
ENG
You can prevent the residual image of the PDP.
TV
Setup
Language
: English
√
Digital NR
: On
√
Miscellaneous
√
PC Setup
Colour Weakness : On
Burn Protection
√
√
√
Move
TV
1
Press the MENU button.
The main menu is displayed.
Result:
2
Press the † or … button to select Setup.
The options available in the Setup group are
Result:
displayed.
3
Press the ENTER (
4
Press the † or … button to select Burn Protection.
5
Press the ENTER (
) button.
The Burn Protection menu is displayed with the
Result:
Pixel Shift selected.
6
Press the ENTER (
√
Time
Enter
Return
Burn Protection
√
Pixel Shift
All White
: Off
√
Signal Pattern
: Off
√
Result:
Move
Enter
TV
Return
:
Horizontal Dot
: Off On
Press the ENTER (
) button. Set to On by pressing the † or …
button for making the screen move per regular hour and
preventing the residual image, then press the ENTER (
)
button.
8
Select the option (Horizontal Dot, Vertical Line, Time) to
be adjusted by pressing the † or … button.
Press the ENTER (
) button.
Off
Vertical Line
: 4
Time
: 4 Min
Move
TV
Enter
) button again.
The Pixel Shift menu is displayed with the
Pixel Shift selected.
7
Pixel Shift
Pixel Shift
) button.
➢
Return
Optimum condition for pixel shift;
Horizontal Dot
2
Vertical Line
4
Time
4MIN
Burn Protection
Pixel Shift
All White
Signal Pattern
Move
: Off Off
: Off On
Enter
46
9
Press the † or … button to reach the required setting.
Press the ENTER (
) button.
10
When you are satisfied with the settings, press the MENU (
button. Press the ENTER (
) button.
11
Press the † or … button to select All White.
Press the ENTER (
) button. Set to On by pressing the † or …
button for removing the residual image after making the screen
white. Press the ENTER (
) button.
Return
)
BN68-00742A-00Eng_0621
2004.6.21
3:52 PM
Page 47
Protecting the Screen Burning (continued)
ENG
12
➢
Press the † or … button to select Signal Pattern.
Press the ENTER (
) button. Set to On by pressing the † or …
button for removing the residual image.
Press the ENTER (
) button.
TV
Burn Protection
Pixel Shift
All White
: Off
Signal Pattern
: Off Off
On
The Signal Pattern and All White feature are
effective after working for a long time.
Move
Enter
Return
Changing the Sound Standard
You can select the type of special sound effect to be used when watching a
given broadcast.
1
Press the MENU button.
Result:
TV
The main menu is displayed.
Result:
3
√
Auto Volume
: Off
√
SRS TSXT
: Off
√
Internal Mute
: Off
√
The options available in the Sound group are
displayed.
Press the ENTER (
Result:
Move
) button.
Enter
TV
Press the ENTER (
5
Select the option by pressing the † or … button.
The sound effects are displayed in the following order.
) button again.
Sound
Mode
: Standard
Standard
Equalizer
Music
Auto Volume
: Off
SRS TSXT
: Off
Internal Mute
: Off
Custom
Standard - Music - Movie - Speech - Custom.
Press the ENTER (
➢
Return
The Mode is selected.
4
6
√
: Standard
Equalizer
Press the † or … button to select Sound.
2
Sound
Mode
) button to confirm.
Move
Movie
Speech
Enter
You can also set these options simply by pressing the S.MODE
(
: Sound Mode) button.
47
Return
BN68-00742A-00Eng_0621
2004.6.21
3:52 PM
Page 48
Adjusting the Sound Settings
ENG
The sound settings can be adjusted to suit your personal preferences.
TV
Sound
Mode
1
Press the MENU button.
The main menu is displayed.
Result:
2
Press the † or … button to select Sound.
The options available in the Sound group are
Result:
displayed.
3
Press the ENTER (
4
Press the † or … button to select Equalizer.
Press the ENTER (
) button.
The Equalizer menu is displayed with the current
Result:
option.
5
Select the option (volume, balance, equalizer) to be adjusted by
pressing the œ or √ button. Press the † or … button to reach the
required setting.
6
When you are satisfied with the settings, press the MENU (
button to store them.
√
: Standard
√
Equalizer
Auto Volume
: Off
√
SRS TSXT
: Off
√
Internal Mute
: Off
√
Move
Enter
Return
Equalizer
TV
10
R
0
L
100 300 1K 3K 10K
√ Move
Adjust
Return
➢
48
) button.
If you make any changes to the equalizer settings, the sound
standard is automatically switched to the Custom.
)
BN68-00742A-00Eng_0621
2004.6.21
3:52 PM
Page 49
Adjusting the Volume Automatically
ENG
Each broadcasting station has its own signal conditions, and so it is not
easy for you to adjust the volume every time the channel is changed.
This feature lets you automatically adjust the volume of the desired
channel by lowering the sound output when the modulation signal is
high or by raising the sound output when the modulation signal is low.
1
2
Sound
Press the MENU button.
The main menu is displayed.
Result:
Mode
Press the ENTER (
4
Press the † or … button to select Auto Volume.
Press the ENTER (
) button.
) button.
5
Select the option (Off or On) by pressing the † or … button.
6
Press the ENTER (
) button to confirm.
√
√
Equalizer
Press the † or … button to select Sound.
The options available in the Sound group are
Result:
displayed.
3
: Standard
Auto Volume
: Off
√
SRS TSXT
: Off
√
Internal Mute
: Off
√
Move
Enter
TV
Return
Sound
Mode
: Standard
Equalizer
Auto Volume
SRS TSXT
Internal Mute
Move
: Off Off
: Off On
: Off
Enter
49
Return
BN68-00742A-00Eng_0621
2004.6.21
3:52 PM
Page 50
Setting the TruSurround XT
ENG
TruSurround XT is a patented SRS technology that solves the problem of
playing 5.1 multichannel content over two speakers. TruSurround delivers
a compelling, virtual surround sound experience through any two-speaker
playback system, including internal television speakers. It is fully
compatible with all multichannel formats.
TV
Sound
Mode
: Standard
√
1
Press the MENU button.
Result:
√
Equalizer
Auto Volume
: Off
√
SRS TSXT
: Off
√
Internal Mute
: Off
√
Press the † or … button until the Sound is selected.
2
Result:
Move
Enter
TV
Return
Sound
Mode
Auto Volume
: Off
SRS TSXT
: Off
Internal Mute
Off
: Off
3D Mono
Stereo
Move
Enter
Return
Press the ENTER (
4
Press the † or … button until the SRS TSXT is selected.
Press the ENTER (
) button.
5
Press the † or … button to change the setting.
(Off, 3D Mono or Stereo.)
6
Press the ENTER (
➢
➢
50
The options available in the Sound group are
displayed.
3
: Standard
Equalizer
The main menu is displayed.
) button.
) button to confirm.
TruSurround XT, SRS and (
) Symbol
are trademarks of SRS Labs, Inc.
TruSurround XT technology is
incorporated under license from SRS
Labs, Inc.
You can also set these options simply by pressing the
SRS TSXT (
)button.
BN68-00742A-00Eng_0621
2004.6.21
3:52 PM
Page 51
Selecting the Internal Mute
ENG
Since the speakers are built in the PDP, you can hear the sound without
connecting separate speakers.
If you want to hear the sound through separate speakers, cancel the
internal amplifier.
1
Press the MENU button.
Result:
2
TV
The main menu is displayed.
: Standard
√
√
Equalizer
Press the † or … button to select Sound.
Result:
Sound
Mode
Auto Volume
: Off
√
SRS TSXT
: Off
√
Internal Mute
: Off
√
The options available in the Sound group are
displayed.
3
Press the ENTER (
4
Press the † or … button to select Internal Mute.
Press the ENTER (
) button.
5
Press the † or … button to change the setting. (Off or On.)
6
Press the ENTER (
Move
) button.
) button to confirm.
Enter
TV
Return
Sound
Mode
: Standard
Equalizer
Auto Volume
: Off
SRS TSXT
: Off
Internal Mute
: Off Off
On
Move
Enter
51
Return
BN68-00742A-00Eng_0621
2004.6.21
3:52 PM
Page 52
Selecting the Sound Mode (depending on the model)
ENG
The “DUAL I-II” button displays/controls the processing and output
of the audio signal. When power is switched on, the mode is
automatically preset to either “DUAL-I ” or “Stereo”, depending on
the current transmission.
NICAM
Stereo
Type of broadcast
On-screen indication
Regular broadcast
(Standard audio)
Mono (Normal use)
Regular +
NICAM Mono
NICAM Mono ↔ Mono
NICAM Stereo
A2
Stereo
NICAM DUAL-I/II
NICAM DUAL-I →
NICAM DUAL-II →
Mono
Regular broadcast
(Standard audio)
Mono
Bilingual or DUAL-I/II
DUAL-I ↔ DUAL-II
Stereo
➢
NICAM Stereo ↔ Mono
(Forced mono)
Stereo ↔ Mono
(Forced mono)
◆ If the receiving conditions deteriorate, listening will be
easier if the mode is set to the Mono.
◆ If the stereo signal is weak and an automatic switching
occurs, then switch to the Mono.
◆ When receiving a mono sound in the AV mode, connect
to the “AUDIO-L” input connector on the side of the
television. If the mono sound comes out only from left
speaker, press the DUAL I-II button.
52
BN68-00742A-00Eng_0621
2004.6.21
3:52 PM
Page 53
Setting the Sleep Timer
ENG
You can select a time period of between 30 and 180 minutes after which
the television automatically switches to Standby mode.
1
TV
Press the MENU button.
Result:
The main menu is displayed.
Press the † or … button to select Setup.
2
Result:
The options available in the Setup group are
displayed.
3
Press the ENTER (
4
Press the † or … button to select Time.
Press the ENTER (
) button.
Result:
Setup
√
Time
Language
: English
√
Digital NR
: On
√
Miscellaneous
√
PC Setup
Colour Weakness : Off
Burn Protection
√
√
√
Move
Enter
Return
) button.
TV
The options available in the Time group are displayed.
Time
Clock
07 : 05 am
√
Sleep Timer
Off
√
On Timer
Off
√
Off Timer
Off
√
Press the † or … button to select Sleep Timer.
Press the ENTER (
) button.
5
Result:
The Sleep Timer menu is displayed with the Min is
selected.
6
Select the preset time intervals (Off, 30, 60, 90, 120, 150, 180)
by pressing the † or … button.
7
Press the œ or √ button to move to the Activation.
8
When you are satisfied with the settings, select Activation to
Yes or No by pressing the † or … button.
9
Press the ENTER (
➢
Move
TV
) button to confirm your selection.
◆ You can also set these options simply by pressing the
SLEEP button.
◆ If the sleep timer is not yet set, Off is displayed.
If the sleep timer is already set, the remaining time
before which the television switches to Standby mode
is displayed.
Enter
Return
Sleep Timer
Min
Activation
--
No
√ Move
Adjust
TV
Return
Sleep Timer
Min
Activation
30
Yes
œ √ Move
Adjust
Off
53
Return
BN68-00742A-00Eng_0621
2004.6.21
3:52 PM
Page 54
Setting and Displaying the Current Time
ENG
TV
You can set the television’s clock so that the current time is displayed by
pressing the “INFO (
)” button. You must also set the time if you wish
to use the automatic on or off timers.
Setup
√
Time
Language
: English
√
Digital NR
: On
√
Miscellaneous
√
PC Setup
Colour Weakness : Off
Burn Protection
√
√
√
Move
Enter
TV
➢
1
Press the MENU button.
The main menu is displayed.
Result:
2
Press the ▼ or ▲ button to select Setup.
The options available in the Setup group are
Result:
displayed.
3
Press the ENTER (
4
Press the ▼ or ▲ button to select Time.
Press the ENTER (
) button.
The options available in the Time group are displayed
Result:
with Clock is selected.
5
Press the ENTER (
6
Press the ¦ or ‹button to move to the hour or minute.
Set the hour, minute or am/pm by pressing the ▼ or ▲ button.
7
When you have finished, press the MENU (
8
Press the INFO (
Return
Time
Clock
07 : 05 am
√
Sleep Timer
Off
√
On Timer
Off
√
Off Timer
Off
√
Move
Enter
TV
Return
Clock
Hour
Min
am/pm
07
05
am
√ Move
Adjust
54
Return
When pressing the “I / ” button (On/Off) on the front of the
television, the clock setting will be reset.
) button.
) button.
) button to exit.
) button to display the current time.
BN68-00742A-00Eng_0621
2004.6.21
3:52 PM
Page 55
Switching the Television On and Off Automatically
ENG
You can set the television’s clock and set the On or Off timers so that the
television will:
◆ Switch on automatically and tune to the channel of your
choice at the time you select
◆ Switch off automatically at the time you select
➢
Press the MENU button.
Result:
The main menu is displayed.
2
Press the ▼ or ▲ button to select Setup.
Result:
The options available in the Setup group are
displayed.
Press the ENTER (
Press the † or … button to select Time.
) button.
Press the ENTER (
Result:
The options available in the Time group are displayed.
5
Press the ▼ or ▲ button to select On Timer.
) button.
Press the ENTER (
Result:
The options available in the On Timer group are
displayed.
√
Language
: English
√
Digital NR
: On
√
Miscellaneous
√
PC Setup
Colour Weakness : Off
Burn Protection
√
√
√
Move
Enter
TV
) button.
4
Setup
Time
The first step is to set the television’s clock (refer to “Setting
and Displaying the Current Time” on the previous page).
1
3
TV
Time
Clock
07 : 05 am
√
Sleep Timer
Off
√
On Timer
Off
√
Off Timer
Off
√
Move
6
7
Press the œ or √ button to move to the Activation.
8
When you are satisfied with the settings, select Activation to
Yes or No by pressing the † or … button.
9
Press the MENU button.
Result:
The options available in the Time group are displayed
again.
10
Press the † or … button to select Off Timer.
) button.
Press the ENTER (
Result:
The Off Timer menu is displayed.
11
Select the Hour, Min, am/pm or Activation by pressing
the œ or √ button. Set these by pressing the † or … button.
12
Press the ENTER (
➢
➢
Enter
TV
Select the Hour, Min, am/pm, Prog., Volume by pressing
the œ or √ button. Set these by pressing the † or … button.
Return
Return
On Timer
Hour
Min
am/pm
12
01
am
Prog.
Volume Activation
1
10
No
√ Move
Adjust
TV
Return
Off Timer
Hour Min am/pm Activation
12
00
am
√ Move
Adjust
) button to confirm.
Absent Power Off
When you set the timer “On”, your television will eventually be
turned off, if you do not operate any controls during the 3 hours
after the TV is turned on by timer. This function is available in
only the timer “On” mode and will prevent a leakage accident
or overheating, caused by your TV left on for a long time due to
the timer “On” (when you are away on holiday, for example).
If no signal is received for 15 minutes, the TV will be
automatically turned off.
55
No
Return
BN68-00742A-00Eng_0621
2004.6.21
3:52 PM
Page 56
Viewing an External Signal Source
ENG
TV
Use the remote control to switch between viewing signal from
connected equipment, such as VCR, DVD, Set-Top-boxs and the TV
source (broadcast or cable).
Input
Source List
√
: TV
√
Edit Name
1
Press the MENU button.
Result:
Press the ▼ or ▲ button to select Input.
2
Move
Enter
TV
Return
Source List
TV
AV1
AV2
AV3
S-Video1
S-Video2
Component1
▼ More
Move
-------------------
Enter
TV
Result:
Press the ENTER (
4
Press the ▼ or ▲ button to select Source List.
Press the ENTER (
) button.
➢
√
: TV
√
Edit Name
Move
Enter
TV
Move
:
:
:
:
:
:
:
When you connect equipment to the TV, you can choose
between the following sets of jacks : AV1, AV2, AV3,
S-Video1, S-Video2, Component1, Component2, PC or
DVI on the TV’s rear panel.
Press the MENU button and select Input.
7
Press the ▼ or ▲ button to select Edit Name.
Press the ENTER (
) button.
Result:
The options available in the Edit Name group
are displayed.
8
Press the ▼ or ▲ button to select external device :
AV1 - AV2 - AV3 - S-Video1 - S-Video2 - Component1 Component2 - PC - DVI.
9
Press the ENTER (
) button.
The Edit Name available are listed.
Result:
10
Select the name by pressing the † or … button.
Press the ENTER (
) button.
11
Set other signal sources (VCR, DVD, Cable STB, HD STB,
Satellite STB, AV Receiver, DVD Receiver, Game,
Camcorder, DVD Combo, DHR or PC) using the same method as
listed above.
---VCR
DVD
Cable STB
HD STB
Satellite STB
†
Enter
Return
➢
➢
56
The options available in the Source List group are
displayed.
6
Return
Edit Name
AV1
AV2
AV3
S-Video1
S-Video2
Component1
Component2
▼ More
) button.
Press the ▼ or ▲ button to select signal source,
then press the ENTER (
) button.
5
Input
Source List
The options available in the Input group are
displayed.
3
Result:
Return
The main menu is displayed.
You can also set these options simply by pressing the
SOURCE (
) button. If you change the external source
while viewing, pictures might take a short period of time
to be switched.
DHR : DVD HDD Recorder.
BN68-00742A-00Eng_0621
2004.6.21
3:52 PM
Page 57
Teletext Feature
ENG
Most television channels provide written information services via
teletext. Information provided includes:
◆ Television programme times
◆ News bulletins and weather forecasts
◆ Sports results
◆ Travel information
This information is divided into numbered pages (see diagram).
Part
Contents
A
Selected page number.
B
Broadcasting channel identity.
C
Current page number or search indications.
D
Date and time.
E
Text.
F
Status information.
FASTEXT information.
➢
Teletext information is often divided between several
pages displayed in sequence, which can be accessed by:
◆ Entering the page number
◆ Selecting a title in a list
◆ Selecting a coloured heading (FASTEXT system)
57
BN68-00742A-00Eng_0621
2004.6.21
3:52 PM
Page 58
Displaying the Teletext Information
ENG
You can display Teletext information at any time on your television.
☛
For Teletext information to be displayed correctly, channel
reception must be stable; otherwise:
◆ Information may be missing
◆ Some pages may not be displayed
1
Select the channel providing the Teletext service by pressing the
P
or
button.
2
Press the TTX/MIX (
Result:
3
Press the TTX/MIX (
) button again.
The screen will be split into two. This Double Teletext
Result:
feature lets you view the actual broadcast and teletext
information separately on the screen.
4
If you wish to display the actual broadcast and teletext
information on a single screen, press the TTX/MIX (
button again.
5
58
) button to activate the teletext mode.
The contents page is displayed. It can be redisplayed
at any time by pressing the
(index) button.
To exit from the teletext display, press the EXIT/TV (
)
) button.
BN68-00742A-00Eng_0621
2004.6.21
3:52 PM
Page 59
Selecting Display Options
ENG
When you have displayed a Teletext page, you can select various
options to suit your requirements.
To display...
Press the...
◆ Hidden text
(answers to quiz games, for example)
(reveal)
◆ The normal screen
(reveal) again
◆ A secondary page by entering its number
(sub-page)
◆ The broadcast when searching for a page
(cancel)
◆ The next page
(page up)
◆ The previous page
(page down)
◆ Double-size letters in the:
• Upper half of the screen
• Lower half of the screen
(size)
• Once
• Twice
◆ The normal screen
• Three times
TV
59
BN68-00742A-00Eng_0621
2004.6.21
3:52 PM
Page 60
Selecting a Teletext Page
ENG
You can enter the page number directly by pressing the numeric buttons
on the remote control.
1
Enter the three-digit page number given in the content by
pressing the corresponding numeric buttons.
Result:
The current page counter is incremented and the
page is then displayed. If the selected page is linked
with several secondary pages, the secondary pages
are displayed in sequence. To freeze the display on a
given page, press the
(hold). Press it again to
resume.
2
If the FASTEXT system is used by the broadcasting company,
the different topics covered on a Teletext page are colour-coded
and can be selected by pressing the coloured buttons on the
remote control.
Press the coloured button corresponding to the topic that you wish
to select; the available topics are given on the status line.
Result:
The page is displayed with other coloured information
that can be selected in the same way.
3
To display the previous or next page, press the corresponding
coloured button.
4
To display the subpage, see the following steps.
◆ Press the
(sub-page) button.
Result:
The available subpages appear.
◆ Select the required sub-page. Sub-pages can be scrolled by
pressing the
or
button.
5
60
When you have finished, press the EXIT/TV (
return to your normal broadcast.
) button to
BN68-00742A-00Eng_0621
2004.6.21
3:52 PM
Page 61
Connecting to the External Devices
ENG
“MONITOR OUT” are used for the equipment with an RGB output, such as
video game devices or video disc players.
VCR
②
Rear of the TV
(Input/Output)
DVD
Decoder /
Video game device
①
Video disc player
Satellite receiver
③
① This end can be fitted with:
◆ Three RCA connectors (VIDEO + AUDIO-L/R)
② If you have a second VCR and wish to copy cassettes tape, connect the source VCR to “AV 1(AV1,
AV2 or AV3)” and the target VCR to “MONITOR OUT” so that you can redirect the signal from
“AV 1(AV1, AV2 or AV3)” to “MONITOR OUT”.
③ When you wish to record a programme, connect the receiver to “AV 1(AV1, AV2 or AV3)” and the VCR
to “MONITOR OUT” so that you can redirect the signal from “AV 1(AV1, AV2 or AV3)” to “MONITOR
OUT”.
61
BN68-00742A-00Eng_0621
2004.6.21
3:52 PM
Page 62
Connecting to the S-Video Input
ENG
The S-VIDEO1 and RCA (AUDIO-L/R) connectors are used for equipment with an S-Video output,
such as a camcorder or VCR.
Rear of the TV
①
and
Camcorder
Side of the TV
①
VCR
and
① To play picture and sound, both the S-VIDEO and RCA connectors must be used.
☛
62
Whenever you connect an audio or video system to your television,
ensure that all elements are switched off. Refer to the documentation
supplied with your equipment for detailed connection instructions
and associated safety precautions.
BN68-00742A-00Eng_0621
2004.6.21
3:52 PM
Page 63
Connecting to the DVI Input
ENG
The “DVI” (video) and “L-AUDIO-R” connectors are used for equipment with a DVI output.
Rear of the TV
Personal Computer
and
Connecting to the PC Input
The “RGB” (video) and “AUDIO” connectors are used for interfacing with your PC.
Rear of the TV
Personal Computer
and
63
BN68-00742A-00Eng_0621
2004.6.21
3:52 PM
Page 64
Connecting to the Component Input
ENG
Rear of the TV
① The “COMPONENT 1” connectors are
①
DVD
②
DTV receiver
used for equipment with a DVD output.
(480i/480P/576i/576P/720P/1080i)
② The “COMPONENT 2” connectors are
used for DTV receiver.
(480i/480P/576i/576P/720P/1080i)
64
BN68-00742A-00Eng_0621
2004.6.21
3:52 PM
Page 65
Connecting and Using the Home Theater System
ENG
Use the Monitor Out ports of the PDP for Home Theater System Connections.
Rear of the TV
Connecting the Home Theater System
① Connect the monitoring audio out L, and
R jacks of the MONITOR OUT on the
rear-side connection panel of the PDP
TV to the AUDIO IN jacks of the DVD
Home Theater System (or AV Receiver)
using the audio cable.
② Press the SOURCE button to select the
desired external device connected to the
PDP TV.
③ If you want to hear the sound through
separate speakers, cancel the internal
amplifier.
②
①
DVD Home Theater
☛
AV Receiver Amplifier
◆ Refer to corresponding user’s manual from the manufacturer for wiring the
speakers to the DVD Home Theater System (or AV Receiver).
◆ Disable the PDP TV internal speaker to enjoy the rich sound through the
speakers of your Home Theater System.
◆ In this case, enjoy the sound from the Home Theater System while the PDP TV
does not produce the audio.
To Display the DVD Home Theater
! Turn the PDP on and press the SOURCE button to select the AV1 (AV2 or AV3) or
Component(1, 2).
@ Be sure to connect the video cable properly if desired external input AV1 (AV2 or AV3) or
Component(1, 2) cannot be selected.
# Play the DVD after activating the DVD Home Theater System.
$ Use the volume control of the Home Theater System while watching the PDP using the DVD
Home Theater, where the PDP TV does not produce the audio.
65
BN68-00742A-00Eng_0621
2004.6.21
3:52 PM
Page 66
Setting up Your PC Software (Windows only)
ENG
The Windows (MS Windows XP) display-settings for a typical computer are shown below. But the actual screens on
your PC will probably be different, depending upon your particular version of Windows and your particular video
card. But even if your actual screens look different, the same, basic set-up information will apply in almost all
cases. (If not, contact your computer manufacturer or Samsung Dealer.)
1. Right click the mouse on the Windows Desktop,
then click on [Properties].
The <Display Dialog-Box> will be displayed.
2. Click on [Settings], then set the <Display Mode>
with reference to the Display Modes Table.
You do not need to change the <Colours> settings.
3. Click on [Advanced].
A new settings dialog box will be displayed.
4. Click on the [Monitor] tab, then set the <Screen
Refresh Rate> with reference to the Display Modes
Table.
Set the <Vertical Frequency> and <Horizontal Frequency>
individually if you can do so instead of setting the <Screen
Refresh Rate>.
5. Press the [OK] button, close the window, then press
the [OK] button on the <Display Registration
Information> window.
Automatic re-booting may commence at this moment.
6. Shutdown the PC, and connect it to your TV.
66
n
BN68-00742A-00Eng_0621
2004.6.21
3:52 PM
Page 67
Input Mode (PC/DVI)
ENG
Both screen position and size will vary depending on the type of PC monitor and its resolution.
The table below shows all of the display modes that are supported:
Video Signal
Dot x Line
640 x 350
640 x 400
720 x 400
640 x 480
IBM PC / AT
Compatible
800 x 600
848 x 480
1024 x 768
Vertical
frequency (Hz)
Horizontal
frequency (kHz)
Vertical
polarity
Horizontal
polarity
70.086
85.080
85.080
70.087
85.039
59.940
72.809
75.000
85.008
56.250
60.317
72.188
75.000
85.061
60.000
72.000
75.000
60.004
70.069
75.029
84.997
31.469
37.861
37.861
31.469
37.927
31.469
37.861
37.500
43.269
35.156
37.879
48.077
46.875
53.674
29.838
36.072
37.650
48.363
56.476
60.023
68.677
N
N
P
P
P
N
N
N
N
N/P
P
P
P
P
P
P
N
N
N
N
N
N
N
N/P
P
P
P
P
nVidia chipset
N
N
P
P
N
N
P
P
(N: Negative / P: Positive)
◆ The interlace mode is not supported.
◆ The television might operate abnormally if a non-standard video format is selected.
Notes
◆ The PC text quality for PS-42S4S is optimum in WVGA mode(848x480@60Hz).
◆ When this television is used as a PC display, 32-bit colour is supported.
◆ Your PC display screen might appear different depending on the manufacturer (and your particular version
of Windows). Check your PC instruction book for information about connecting your PC to a television.
◆ If a vertical and horizontal frequency-select mode exists, select 60Hz (vertical) and 31.5kHz (horizontal).
In some cases, abnormal signals (such as stripes) might appear on the screen when the PC power is turned
off (or if the PC is disconnected). If so, press the SOURCE button to enter the Video mode. Also, make sure
that the PC is connected.
◆ When connecting a notebook PC to the television, make sure that the PC screen is displayed through only
the television (Otherwise, random signals might appear).
◆ When horizontal synchronous signals seem irregular in PC mode, check PC power saving mode or cable
connections.
◆ The Display Settings Table above complies to the IBM/VESA standards, and based on the analog input.
◆ The DVI support mode is regarded as same to the PC support mode.
◆ The best timing for the vertical frequency to each mode is 60Hz.
67
BN68-00742A-00Eng_0621
2004.6.21
3:52 PM
Page 68
Pin Configurations
ENG
PC Input Connector
(15Pin)
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
68
DVI Input Connector
(24Pin)
PC IN
Red (R)
Green (G)
Blue (B)
Grounding
Grounding (DDC)
Red (R) Grounding
Green (G) Grounding
Blue (B) Grounding
Reserved
Sync Grounding
Grounding
Data (DDC)
Horizontal sync.
Vertical sync.
Clock (DDC)
Pin
Signal
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
T.M.D.S. Data2T.M.D.S. Data2+
T.M.D.S. Data2/4 Shield
T.M.D.S. Data4T.M.D.S. Data4+
Clock (DDC)
Data (DDC)
Not Connected
T.M.D.S. Data1T.M.D.S. Data1+
T.M.D.S. Data1/3 Shield
T.M.D.S. Data3T.M.D.S. Data3+
+5V Power
5V Grounding
Hot Plug Detect
T.M.D.S. Data0T.M.D.S. Data0+
T.M.D.S. Data0/5 Shield
T.M.D.S. Data5T.M.D.S. Data5+
T.M.D.S. Clock Shield
T.M.D.S. Clock+
T.M.D.S. Clock-
BN68-00742A-00Eng_0621
2004.6.21
3:52 PM
Page 69
Troubleshooting: Before Contacting Service Personnel
ENG
Before contacting Samsung after-sales service, perform the following simple checks.
If you cannot solve the problem using the instructions below, note the model and serial number of the
television and contact your local dealer.
No sound or picture
◆ Check that the mains lead has been connected to a wall socket.
◆ Check that you have pressed the “ I ” button (On/Off) and the
POWER ( ) button.
◆ Check the picture contrast and brightness settings.
◆ Check the volume.
Normal picture but no sound
◆ Check the volume.
◆ Check whether the volume MUTE (
control has been pressed.
) button on the remote
No picture or black and white picture
◆ Adjust the colour settings.
◆ Check that the broadcast system selected is correct.
Sound and picture interference
◆ Try to identify the electrical appliance that is affecting the television,
then move it further away.
◆ Plug your television into a different mains socket.
Blurred or snowy picture,
distorted sound
◆ Check the direction, location and connections of your aerial.
This interference often occurs due to the use of an indoor aerial.
Remote control malfunctions
◆ Replace the remote control batteries.
◆ Clean the upper edge of the remote control (transmission window).
◆ Check the battery terminals.
69
BN68-00742A-00Eng_0621
2004.6.21
3:52 PM
Page 70
Programming the Remote Control for Other Components
ENG
CABLE CODE LIST
Anvision
GI
Hamlin
Hitachi
Jerrold
Macom
Magnavox
Oak
Panasonic
Philips
Pioneer
RCA
Regal
Regency
SA
Samsung
Scientific Atlanta
Sprucer
Stargate 2000
Sylvania
Texscan
Tocom
Universal
Viewstar
Wamer amex
Zenith
70
017, 018
041
003, 024, 031
025, 030
038, 039
025, 030
019, 023, 028
026
003, 022, 027, 037, 044
019, 021, 023, 028
018, 020, 004, 044
014, 022, 040
003
015, 023
042, 043
000, 001, 002, 003, 004, 005, 006, 007
042, 043
022
036
016
016
032
033, 034
019, 021,023, 028
046
017, 029, 035, 037, 045
DVD CODE LIST
Samsung
Samsung
JVC
PROSCAN, RCA
Panasonic
LG(Goldstar)
Sony
Denon
Curtis Mathes
000
001
002
003
005
006
007
008
009
BN68-00742A-00Eng_0621
2004.6.21
3:52 PM
Page 71
Programming the Remote Control for Other Components (continued)
ENG
VCR CODE LIST
Admiral
020
Aiwa
025
Akai
027, 004, 032
Audio Dynamics
007, 026
Bell&Howell
018
Broksonic
022
Candle
002, 006, 003, 015, 008, 055
Canon
021, 056
Citizen
002, 006, 003, 015, 008, 055
Colortyme
007
Craig
002, 024
Curtis Mathes 002, 017, 007, 008, 021, 025, 056, 064, 066
Daewoo
003, 015, 010, 011, 012, 013, 014, 016
DBX
007, 026
Dimensia
017
Dynatech
034
Emerson
001, 003, 006, 021, 022, 025, 030, 032, 034,
040, 047, 050, 052, 060, 063, 065, 066, 067, 069
Fisher
018, 024, 028, 029, 048, 051, 061
Funai
025
General Electric
017, 002, 021, 005, 056
Go Video
002
LG(Goldstar)
006, 007, 008, 009, 010
Harman Kardon
007
Hitachi
019, 025, 041, 042
Instant Replay
021
JC Penny
002, 007, 018, 019, 021, 026, 037, 041, 054, 056
JVC
007, 008, 018, 021, 026, 037
Kenwood
007, 008, 018, 026, 037
KLH
070
Lioyd
025
Logik
038
LXI
025
Magnavox
021, 036, 056, 059
Marantz
018, 021, 007, 026, 037, 008, 062, 036
Marta
006
MEI
021
Memorex
006, 021, 024, 025
MGA
034
Midland
005
Minolta
019, 041
Mitsubishi
019, 034, 041, 046
Montgomery Ward
020
MTC
002, 025
Multitech
002, 025, 038, 005
NEC
Optimus
Panasonic
Pentax
Pentex Research
Philco
Philips
Pioneer
Portland
PROSCAN
Quartz
Quasar
Radio Shack/Realistic
018, 007, 026, 037, 008, 062, 064
020
021, 056, 071, 072
019, 041
008
021, 036, 056, 059
021, 036
019, 026, 039, 053
015, 049, 055
017
018
021, 056
006, 018, 020, 021, 024,
025, 029, 034, 048, 056
RCA
017, 019, 002, 021, 035, 041, 043, 057, 068
Samsung
000, 001, 002, 003, 004, 005
Sansui
026
Sanyo
018, 024
Scott
003, 047, 052, 067
Sears
018, 019, 006, 024, 028, 029, 041, 048, 051
Sharp
020, 034, 045, 015
Shimom
027, 033, 038, 058
Signature
025
Sony
027, 033, 044
Sylvania
021, 025, 036, 056, 059
Symphonic
025
Tandy
018, 025
Tashika
006
Tatung
037
Teac
025, 037, 068
Technics
021
Teknika
021, 006, 025, 031
TMK
066
Toshiba
003, 019, 029, 051, 052
Totevision
002, 006
Unitech
002
Vector Research
007, 026
Victor
026
Video Concepts
007, 026
Videosonic
002
Wards
002, 003, 006, 019, 020, 021, 024,
025, 034, 038, 041
Yamaha
007, 008, 018, 026, 037
Zenith
023, 027, 033, 073
71
BN68-00742A-00Eng_0621
2004.6.21
3:52 PM
Page 72
- AFTER SALES SERVICE
- Do not hesitate to contact your retailer or service agent
if a change in the performance of your product indicates
that a faulty condition may be present.
ELECTRONICS
BN68-00742A-00
Download PDF