Samsung | CS-29Z50MH | Samsung CS-29Z50MH User Manual

AA68-03867A-06Eng_Ma/Afirc
2/20/08
6:26 PM
COLOR TELEVISION
CS-29Z40/29Z45/29Z50/29Z57/29Z58
29U50/29U57
Owner’s Instructions
Page 1
Connection Panel (depending on the model)
➢
The actual configuration of your TV may be different,
depending on your model.
Rear Panel
Before operating, please read this manual thoroughly,
and retain it for future reference.
Register your product at
www.samsung.com/global/register
or
cable television network
Connecting to the RCA Output
6 connectors are used for equipment, such as a
The RCA6
recording VCR or audio system.
Connecting to the RCA Input
The RCA4 and RCA5 connectors are used for equipment,
such as a VCR, DVD, decoder, satellite receiver, video game
device, or video disc player. (When using the mono
equipment, connect to the AUDIO-L input connector.)
7 connectors are used for equipment such as a
The RCA7
DVD with component output.
Front (or Side) Panel
Control Panel (depending on the model)
➢
The actual configuration of your TV may be different,
depending on your model.
3 S-Video input
Front (or Side) Panel
2 Video input
☛
1
2
3
4
5
6
Remote control sensor
Standby indicator
Power on/off
On-screen menu display
Volume adjustment
Channel selection
◆ You can use the 6 buttons to switch the TV on when it is
in standby mode depending on the model.
◆ The 5 and 6 buttons also have the same function as the
œ/√/†/… buttons on the remote control.
◆ If the remote control no longer works or you have
misplaced it, you can use the controls on the panel of the
television.
1 Audio input
Whenever you connect an audio or video system to your
television, ensure that all elements are switched off.
Please be sure to match the color coded input terminals
and cable jacks.
Connecting to an Aerial or Cable Television Network
Connect the aerial or network input cable to the 1 (75 Ω
coaxial socket).
To view television channels correctly, a signal must be
received by the set from one of the sources: an outdoor
aerial, cable television network, or satellite network.
If you are using an indoor aerial, you may need to adjust it
when tuning your television until you obtain a picture that is
both sharp and clear.
Connecting to the SCART Input/Output
The SCART2 and SCART3 connectors are used for
equipment, such as a VCR, DVD, decoder, satellite receiver,
video game device, or video disc player.
The SCART2 is also used for equipment with an RGB
output, such as a video game device or video disc player.
☛
Please be sure to match the color coded input terminals
and cable jacks.
Connecting to the RCA Input
The 1 (AUDIO-L/R) and 2 (VIDEO) connectors are used
for equipment, such as a camcorder, video disc player, or
video game device.
Connecting to the S-VIDEO Input
The 3 (S-VIDEO IN) and 1 (AUDIO-L/R) connectors are
used for equipment with an S-Video output, such as a
camcorder or VCR.
continued...
English - 1
AA68-03867A-06
AA68-03867A-06Eng_Ma/Afirc
2/20/08
6:26 PM
Remote Control (depending on the model)
➢
Operation of remote control may be affected by bright
artificial light near to the TV.
Page 2
4
/
Used to increase or
decrease the volume.
5 MENU
Used to display the onscreen menu or return to
the previous menu.
6 …/†/œ/√
Used to control the
cursor in the menu.
7 S.MENU
Used to display the
sound menu.
8 TURBO
Used to select the turbo
sound option.
9 P.SIZE
Used to change the
screen size.
0 DUAL I-II
Used to select the
sound mode.
! SOURCE
Used to display all of the
available video sources.
@ INFO
Used to view the
channel information and
setting status you
selected.
# PRE-CH
Used to switch
repeatedly between the
last two channels
displayed.
$ P /
Used to display the next
or previous stored
channel.
% EXIT
Used to exit from any
display or return to
normal viewing.
^ MUTE
Used to switch the
sound off temporarily. To
turn the sound back on,
press the MUTE, , or
button.
& ENTER
While using the onscreen menus, press the
ENTER button to
activate (or change) a
particular item.
* S.MODE
Used to select the
sound effect.
( P.MODE
Used to select the
picture effect.
) TV
Used to return to the TV
mode when it is in
external input mode.
a SLEEP
Used to select a preset
time interval for
automatic turn off.
Installing Batteries
1 POWER
Used to switch the TV
on and off.
2 Numeric buttons
Used to select channels
directly.
3 -/-Used to select a channel
numbered ten or over.
Press this button, then
“--” symbol is
displayed. Enter the
two-digit channel
number.
Remove the cover. Install two AAA
size batteries, then replace the cover.
When the remote control does not
operate normally, check that the “+”
and “-” ends of the batteries are inserted correctly or the
batteries are drained.
➢ Do not mix battery types, i.e. alkaline and manganese.
English - 2
Switching the Television On and Off
The mains lead is attached to the rear of the television.
1
Plug the mains lead into an appropriate socket.
➢ The main voltage is indicated on the rear of the
television and the frequency is 50 or 60Hz.
2
Press the “ I ” button (On/Off) on the front (or side) of the
television.
3
Press the POWER button on the remote control to
switch the television on. The programme that you were
watching last is re-selected automatically. If you have
not yet stored any channels, no clear picture appears.
Refer to “Channel - Auto Store” or “Channel - Manual
Store” on page 4.
➢ If the television is initially powered on, several basic
customer settings proceed automatically. Refer to
“Setup - Plug & Play” on page 3.
4
To switch the television off, press the “ I ” button (On/Off)
on the front (or side) of the television.
Placing the Television in Standby Mode
The television can be placed in standby mode, in order to
reduce power consumption and wear of the cathode ray
tube. Standby mode can be useful when you wish to
interrupt viewing temporarily (during a meal, for example).
1
Press the POWER button on the remote control while
viewing.
The television is in standby mode.
2
To switch the television back on, simply press it again.
☛
Do not leave the television in standby mode for long
periods of time (when you are away on holiday, for
example). Turn the television off by pressing the “ I ”
button (On/Off) on the front (or side) of the television. It
is best to unplug the set from the mains and aerial.
AA68-03867A-06Eng_Ma/Afirc
2/20/08
6:26 PM
2
Viewing the Menus
1
he
2
sic
o
Press the MENU button.
The main menu is displayed on the screen. Its left side
has five icons: Input, Picture, Sound, Channel, and
Setup.
Press the … or † button to select one of the icons.
Press the ENTER button to access the icon’s sub-menu.
3
Press the … or † button to move to items in the menu.
Press the ENTER button to enter items in the menu.
4
Press the …/†/œ/√ button to change the selected
items. Press the MENU button to return to the previous
menu.
e
5
Page 3
Press the EXIT button to exit from the menu.
Off)
3
.
Language
Enter
To search the channels,
select Search by pressing
the … or † button. Press
the ENTER button.
Press the œ or √ button to
move to the hour or minute.
Set the hour or minute by
pressing the … or † button.
Start
Enter
Return
Search
P 1
102MHz
7 %
Stop
Enter
Return
Time
TV
--:-Clock
Sleep Timer
:
--:-On Timer
Off Timer - - : - On Timer Volume :
Move
Enter
am
Off
am Off
am Off
10
Return
continued...
Enter
Enjoy your watching
When you have finished,
press the MENU button.
The Enjoy your watching is displayed, and then the
channel which has been stored will be activated.
Re-setting the Plug & Play
Method: MENU ➜ …/†
(Setup) ➜ ENTER ➜ …/†
(Plug & Play) ➜ ENTER
Setup
TV
√
Plug & Play
Language
: English
Time
Child Lock
Blue Screen : Off
Melody
: On
Demonstration
Move
Enter
√
√
√
√
√
Return
Search
Français
Türkçe
9
Return
6
Press the ENTER button
again to start search
channels. To stop the search,
press the ENTER button.
When the channel
searching has finished, the
Time menu is displayed
with Clock selected.
√
√
English
Move
It
Move
:
Press the … or † button to select your area. Press the
ENTER button.
8
Plug & Play
Area
Search
ASIA W/EUROPE
Belgie
CIS E/EUROPE
CHINA
HONGKONG U/K
AUSTRALIA
NZ/INDONESIA
SOUTH AFRICA
AMERICA
5
When the television is initially powered on, several basic
customer settings proceed automatically and subsequently.
The following settings are available.
If the television is in standby
mode, press the POWER
button on the remote control.
The Plug & Play is
displayed. It flickers for a little
while, and then Language
menu is displayed.
Auto Store
TV
Press the ENTER button again.
Setup - Plug & Play
1
Make sure that the antenna
is connected to the
television (refer to page 1).
Press the ENTER button.
The Auto Store menu is
displayed with Area
selected.
4
7
e
Check antenna input.
Select the appropriated
language by pressing the
Enter
Exit
… or † button. Press the
ENTER button.
The Check antenna input. is displayed.
➢ If any language is not selected, the language menu
will disappear about 30 seconds later.
Input (depending on the model) Source List / Edit Name
Source List
TV
◆ Source List
TV
You can switch between
AV1
---viewing signal from
AV2
---S-Video
---connected equipment, such
Component
---as a VCR, DVD, set-top box,
and the TV source
Move
Enter
Return
(broadcast or cable).
You
can
change
the
required
external
source
simply
➢
by pressing the SOURCE button on the remote
control. It might take a short period of time for
pictures to be switched. To return to the TV mode,
press the TV button on the remote control.
◆ Edit Name
You can give a name to the
external source.
Edit Name
TV
AV1
AV2
S-Video
Component
---: Belgie
VCR
: DVD
: Cable STB
STB
: Sat.
AV Recv.
√
√
√
DVD Recv.
Game
Camcorder
DVD Combo
continued...
Move
English - 3
Enter
Return
AA68-03867A-06Eng_Ma/Afirc
2/20/08
6:26 PM
Page 4
Channel - Auto Store
Channel - Manual Store
Channel - Add/Delete (depending on the model)
You can scan for the frequency ranges available to you (and
availability depends on your country). Automatically allocated
programme numbers may not correspond to actual or
desired programme numbers. However you can sort
numbers manually and clear any channels you do not wish
to watch.
Manual Store
TV
You can store channels,
Programme
: P 3
including those received via
Color System : AUTO
√
cable networks. When storing
Sound System : BG
√
Search
: 46MHz
channels manually, you can
Channel
: C 1
Store
: ?
choose:
- Whether or not to store each
Move
Adjust
Return
of the channels found
- The programme number of each stored channel which
you wish to identify
Add/Delete
TV
You can exclude channels you
P 1 : Added
have chosen from the channels
P 2 : Added
you scanned. When you scan
P 3 : Added
P 4 : Added
through the stored channels,
P 5 : Added
those you have chosen to skip
are not displayed. All of the
Move
Enter
Return
channels that you did not
specifically choose to skip are displayed during scanning.
Auto Store
Channels are sorted and stored TV
ASIA W/EUROPE
Area
: Belgie
√
in the order which reflects their
CIS E/EUROPE
Search
√
CHINA
position in the frequency range
HONGKONG U/K
AUSTRALIA
(with lowest first and highest
NZ/INDONESIA
last). The programme originally
SOUTH AFRICA
AMERICA
selected is then displayed.
Move
Enter
Return
To
stop
the
search
before
it
➢
has finished, press the
Search
P 1
102MHz
MENU button.
7 %
When finished, the Sort menu is
Stop
displayed. To sort the stored
Enter
Return
channels into the desired
numerical order, refer to “Channel - Sort”. To exit without
sorting, press the EXIT button.
◆ Programme (Programme number to be assigned to a
channel)
◆ Color System: AUTO/PAL/SECAM/NT4.43/NT3.58
◆ Sound System: BG/DK/I/M
◆ Search (When you do not know the channel numbers):
The tuner scans the frequency range until the first
channel or the channel that you selected is received on
the screen.
◆ Channel (When you know the number of the channel to
be stored)
➢ You can also select the channel number directly by
pressing the numeric buttons (0~9).
◆ Store (When you store the channel and associated
programme number)
➢
☛
Channel - Sort (depending on the model)
This operation allows you to
change the programme numbers
of stored channels. This
operation may be necessary
after using auto store.
Sort
TV
From
To
Store
: P 1
: P-: ?
◆ From: Channel number to
be changed.
◆ To: New channel number to be identified.
◆ Store: Confirmation the exchange of channel numbers.
Move
Adjust
Return
If there is no sound or abnormal sound, re-select the
sound standard required.
Channel mode
◆ P (Programme mode): When completing tuning, the
broadcasting stations in your area have been
assigned to position numbers from P00 to P99. You
can select a channel by entering the position number
in this mode.
◆ C (Real channel mode): You can select a channel by
entering the assigned number for each air
broadcasting station in this mode.
◆ S (Cable channel mode): You can select a channel by
entering the assigned number for each cable channel
in this mode.
English - 4
Select Added or Deleted by pressing the ENTER button
repeatedly.
Channel - LNA (depending on the model)
This function is very useful in the
situation that the TV is used in
weak signal. LNA amplifies the
TV signal in the weak signal
area, but not noise.
Channel
TV
Auto Store
Manual Store
Add/Delete
Sort
LNA
Move
Enter
:
Off
On
√
√
√
√
√
Return
◆ LNA (Low Noise Amplifier) setting is to be made for
each channel.
◆ If the picture is noisy with the LNA set to On, select Off.
◆ Depending on areas, factory mode of LNA will be set up
as On or Off.
AA68-03867A-06Eng_Ma/Afirc
l)
te
turn
2/20/08
6:26 PM
Setup - Time
Setup - Child Lock
Time
TV
◆ Clock
- - : - - am
Clock
You can set the television
Sleep Timer
: Off
- - : - - am Off
clock so that the current time
On Timer
Off Timer - - : - - am Off
is displayed when pressing
On Timer Volume : 10
the INFO button on the
remote control. You must
Move
Enter
Return
also set the time if you wish
to use the automatic on or off timers.
➢ When pressing the “ I ” button (On/Off) on the front
(or side) of the television, the clock setting will be
reset.
Child Lock
TV
This feature allows you to
Child Lock
: On
√
prevent unauthorized users,
Programme
: P 1
such as children, from watching
Lock
: ?
unsuitable programmes by
muting out video and audio.
Child Lock cannot be released
Move
Enter
Return
using front (or side) panel
buttons. Only remote control can release the Child Lock
setting, so keep the remote control away from children.
◆ Child Lock: On/Off
If you want to unlock a channel, set to Off.
◆ Programme: Channel number to be locked.
◆ Lock: When press the ENTER button, the Locked is
displayed.
◆ Sleep Timer
You can select a time period of between 30 and 180
minutes after which the television automatically switches
to standby mode.
➢ You can select these options simply by pressing the
SLEEP button on the remote control. If the sleep
timer is not yet set, Off is displayed. If it is already
set, the remaining time before which the television
switches to standby mode is displayed.
◆ On Timer / Off Timer
You can set the On/Off timers so that the television will
switch on or off automatically at the time you select.
☛ You must set the clock first.
el
√
√
√
√
√
turn
for
f.
p
Page 5
◆ On Timer Volume
The preferred volume can be set for when the timer
automatically turns on the television.
☛
Auto Power Off
When you set the timer “On”, the TV will eventually turn
off, if no controls are operated for 3 hours after the TV
was turned on by timer. This function is only available
in timer “On” mode and prevents overheating, which
may occur if a TV is on for too long.
➢
If any channel is locked, you can not access to the Channel
and Child Lock menu by using the control buttons on the TV
panel (the Not available is displayed in the Child Lock
menu). You can access by using the remote control only.
Setup - Language / Blue Screen /
Melody / Demonstration
◆ Language
It is variable depending on
the model. When you start
using the television for the
first time, you must select the
language which will be used
for displaying menus and
indications.
√
Plug & Play
Language
: English
Time
Child Lock
Blue Screen : Off
Melody
: On
Demonstration
Move
Enter
√
√
√
√
√
◆ Custom: Contrast/Brightness/Sharpness/
Color/Tint (NTSC only)
The television has several settings which allow you to
control the picture quality.
➢ If you make any changes to these settings, the
picture mode is automatically switched to Custom.
◆ Size
You can select the picture size which best corresponds to
your viewing requirements. It is variable depending on
the model.
➢ You can change the picture size simply by pressing
the P.SIZE button on the remote control.
Exit
◆ Blue Screen
If no signal is being received or the signal is very weak, a
blue screen automatically replaces the noisy picture
background. If you wish to continue viewing the poor
picture, you must set the Blue Screen to Off.
◆ Melody
You can hear melody sound when the television is
powered on or off.
◆ Demonstration
To become familiar with the various menus provided by
the television, you can view the in built demonstration.
Each of the menu options is displayed in turn. To exit
from the demonstration, press the EXIT button.
English - 5
Picture
TV
◆ Mode: Dynamic/
Mode
: Dynamic
√
Standard/Movie/Custom
Custom
√
You can select the type of
Color Tone
: Normal
√
Size
: Normal
√
picture which best
Digital NR
: Off
√
PIP
√
corresponds to your viewing
requirements.
Move
Enter
Exit
➢ You can select these
options simply by pressing the P.MODE button on
the remote control.
◆ Color Tone: Normal/Cool2/Cool1/
Warm1/Warm2
Setup
TV
Picture (depending on the model) Mode / Custom /
Color Tone / Size /
Digital NR
◆ Digital NR
If the signal received by the television is weak, you can
activate this feature to reduce any static and ghosting
that may appear on the screen.
AA68-03867A-06Eng_Ma/Afirc
2/20/08
6:26 PM
Page 6
Picture - PIP (depending on the model)
You can display a sub picture within the main picture of TV
programme or external A/V devices such as VCR or DVD. In
this way you can watch TV program or monitor the video
input from any connected devices while watching TV or other
video input.
Picture
TV
Mode
: Dynamic
Custom
Color Tone
: Normal
Size
: Normal
Digital NR
: Off
PIP
Move
Enter
Exit
PIP
TV
√
√
√
√
√
√
PIP
Source
Swap
Size
Position
Programme
Move
√
√
√
√
√
√
: On
: TV
: Large
:
: P 1
Enter
Return
◆ PIP: On/Off
You can activate or deactivate the PIP funtion. 1
◆ Source
You can select a source of the sub-picture. 2
➢ Depending on the models, the sub-picture can be
viewed only when a source different from the main
picture's is selected. If a TV programme is viewed
on the main picture, the sub-picture is not available
for TV programmes. If a TV source is selected, the
message Not available is displayed.
◆ Swap
You can interchange the main picture and sub-picture. 3
◆ Size: Small/Large
You can select a size of the sub-picture.
◆ Position:
/ / /
You can select a position of the sub-picture.
◆ Programme
You can select a channel of the sub-picture only when
the Source is set to TV.
Easy functions of the remote control
You can freeze the sub-picture.
Sound (depending on the model) Mode / Equalizer /
Auto Volume / Pseudo Stereo /
Turbo Plus
Sound
TV
◆ Mode: Standard/Music
Mode
: Custom
√
/Movie/Speech/Custom
Equalizer
√
You can select the type of
Auto Volume
: Off
√
Pseudo Stereo : Off
√
special sound effect to be
Turbo Plus
: Off
√
used when watching a given
broadcast.
Move
Enter
Exit
➢ You can select these
options simply by pressing the S.MODE button on
the remote control.
Selecting the Sound Mode
(depending on the model)
The DUAL I-II button
displays/controls the processing
and output of the audio signal.
When power is switched on, the
mode is automatically preset to either “Dual-I” or “Stereo”,
depending on the current transmission.
◆ NICAM Stereo
Type of broadcast
On-screen indication
Regular broadcast
(Standard audio)
Mono
(Normal use)
◆ Equalizer
The television has several settings which allow you to
control the sound quality.
➢ If you make any changes to these settings, the
sound mode is automatically switched to Custom.
◆ Auto Volume
Each broadcasting station has its own signal conditions,
and so it is not easy to adjust the volume every time the
channel is changed. This feature lets you automatically
adjust the volume of the desired channel by lowering the
sound output when the modulation signal is high or by
raising the sound output when the modulation signal is
low.
◆ Pseudo Stereo
This feature converts a monaural sound signal into two
identical left and right channels. Once the Pseudo
Stereo is set to On or Off, these settings apply to the
sound effects such as Standard, Music, Movie, and
Speech.
◆ Turbo Plus
This feature suitably emphasizes both higher and lower
bands of sound (and includes other effects). You can
enjoy more magnificent and dynamic sound when
watching music, movie, or other channels.
➢ You can change the options simply by pressing the
TURBO button on the remote control.
English - 6
Regular +
NICAM Mono
Mono
NICAM
↔
Mono
(Normal)
NICAM Stereo
Stereo
NICAM
↔
Mono
(Normal)
NICAM Dual-I/II
Dual-I ↔ Dual-II ↔ Mono
NICAM
NICAM
(Normal)
◆ A2 Stereo
Type of broadcast
On-screen indication
Regular broadcast
(Standard audio)
Mono
(Normal)
Bilingual or Dual-I/II
Stereo
➢
Dual-I
Stereo
↔
↔
Dual-II
Mono
(Forced mono)
◆ If the receiving conditions deteriorate, listening will
be easier if the mode is set to the Mono.
◆ If the stereo signal is weak and an automatic
switching occurs, then switch to the Mono.
◆ When receiving a mono sound in the AV mode,
connect to the “AUDIO-L” input connector on the
panel (front or side). If the mono sound comes out
only from left speaker, press the DUAL I-II button.
AA68-03867A-06Eng_Ma/Afirc
2/20/08
6:26 PM
Page 7
Teletext Feature (depending on the model)
Most television stations provide written information services
via teletext. The index page of the teletext service gives you
information on how to use the service. In addition, you can
select various options to suit your requirements by using the
remote control buttons.
☛ For teletext information to be displayed correctly,
channel reception must be stable. Otherwise,
information may be missing or some pages may not be
displayed.
Troubleshooting
1
2
3
4
5
6
o
al)
ll
ut
.
7
8
9
0
!
@
(hold)
Used to hold the display on a given page if the selected
page is linked with several secondary pages which follow on
automatically. To resume, press it again.
(index)
Used to display the index (contents) page at any time while
you are viewing teletext.
(sub-page)
Used to display the available sub-page.
(size)
Press to display the double-size letters in the upper half of
the screen. For lower half of the screen, press it again. To
display normal screen, press it once again.
(teletext on/mix)
Press to activate teletext mode after selecting the channel
providing the teletext service. Press it again to overlap the
teletext with the current broadcasting screen.
(mode)
Press to select the teletext mode (LIST/FLOF). If you press it
in the LIST mode, it switches into the List save mode. In the
List save mode, you can save teletext page into list using the
(store) button.
(reveal)
Used to display the hidden text (answers to quiz games, for
example). To display normal screen, press it again.
(page up)
Used to display the next teletext page.
(page down)
Used to display the previous teletext page.
(cancel)
Used to display the broadcast when searching for a page.
Coloured buttons (red/green/yellow/blue)
If the FASTEXT system is used by a broadcasting company,
the different topics covered on a teletext page are colourcoded and can be selected by pressing the coloured buttons.
Press one of them corresponding to the required. The page
is displayed with other coloured information that can be
selected in the same way. To display the previous or next
page, press the corresponding coloured button.
(store)
Used to store the teletext pages.
English - 7
Before contacting the Samsung after-sales service, perform
the following simple checks. If you cannot solve the problem
using the instructions below, note the model and serial
number of the television and contact your local dealer.
No sound or picture
◆ Check that the mains lead has been connected to a
wall socket.
◆ Check that you have pressed the “ I ” button (On/Off)
and the POWER button.
◆ Check the picture contrast and brightness settings.
◆ Check the volume.
Normal picture but no sound
◆ Check the volume.
◆ Check whether the volume MUTE button on the
remote control has been pressed.
No picture or black and white picture
◆ Adjust the color settings.
◆ Check that the broadcast system selected is correct.
Sound and picture interference
◆ Try to identify the electrical appliance that is affecting
the television, then move it further away.
◆ Plug the television into a different mains socket.
Blurred or snowy picture, distorted sound
◆ Check the direction, location and connections of your
aerial.
This interference often occurs due to the use of an
indoor aerial.
Remote control malfunctions
◆ Replace the remote control batteries.
◆ Clean the upper edge of the remote control
(transmission window).
◆ Check that the “+” and “-” ends of the batteries are
inserted correctly.
◆ Check that the batteries are drained.
AA68-03867A-06Eng_Ma/Afirc
2/20/08
6:26 PM
Page 8
OSD Map
Input
Picture
Sound
Channel
✽ : It is variable depending on the model.
- Source List ✽
- Edit Name
-
-
Mode
Custom
Colour Tone
Size ✽
Digital NR
PIP ✽
Mode
Equalizer
Auto Volume
Pseudo Stereo
Turbo Plus
- Auto Store
- Manual Store
- Add/Delete
- Sort
- LNA ✽
Setup
- Plug & Play
- Language ✽
- Time
-
Child Lock
Blue Screen
Melody
Demonstration
- VCR / DVD / Cable STB / Sat. STB / AV Recv. / DVD Recv. / Game /
Camcorder / DVD Combo
- Dynamic / Standard / Movie / Custom
- Contrast / Brightness / Sharpness / Color / Tint (NTSC only)
- Normal / Cool2 / Cool1 / Warm1 / Warm2
-
Off / On
PIP
Source ✽
Swap
Size
Position
Programme
Off / On
- Off / On
- Off / On
- Off / On
-
- ASIA W/EUROPE / CIS E/EUROPE / CHINA /
HONGKONG U/K / AUSTRALIA / NZ/INDONESIA /
SOUTH AFRICA / AMERICA
Search
Programme
Color System ✽ - AUTO / PAL / SECAM / NT4.43 / NT3.58
Sound System ✽ - BG / DK / I / M
Search
Channel
Store
- Off / On
-
Standard screen format televisions (4:3, the aspect
ratio of the screen width to height) are primarily
designed to view standard format full-motion video.
The images displayed on them should primarily be in
the standard 4:3 ratio format and constantly moving.
Displaying stationary graphics and images on screen,
such as the dark top and bottom letterbox bars (wide
screen pictures), should be limited to no more than
15% of the total television viewing per week.
Wide screen format televisions (16:9, the aspect ratio
of the screen width to height) are primarily designed to
view wide screen format full-motion video. The images
displayed on them should primarily be in the wide
screen 16:9 ratio format, or expanded to fill the screen
if your model offers this feature, and constantly
moving. Displaying stationary graphics and images on
screen, such as the dark side-bars on non-expanded
standard format television video and programming,
should be limited to no more than 15% of the total
television viewing per week.
- Standard / Music / Movie / Speech / Custom
- Area ✽
Important Warranty Information
Regarding Television Format Viewing
Clock
Sleep Timer
On Timer
Off Timer
On Timer Volume
Off / On
Off / On
Off / On
Additionally, viewing other stationary images and text
such as stock market reports, video game displays,
station logos, web sites or computer graphics and
patterns, should be limited as described above for all
televisions. Displaying any stationary images that
exceed the above guidelines can cause uneven aging
of picture tubes (CRTs) that leave subtle, but
permanent burned-in ghost images in the television
picture. To avoid this, vary the programming and
images, and primarily display full screen moving
images, not stationary patterns or dark bars.
On television models that offer picture sizing features,
use these controls to view the different formats as a
full screen picture.
Be careful in the selection and duration of television
formats used for viewing. Uneven CRT aging as a
result of format selection and use, as well as other
burned-in images, is not covered by your Samsung
limited warranty.
English - 8
Download PDF