Samsung | PH55F | Samsung PH55F Quick start guide

DVI / RGB /
MAGICINFO IN
04
HDMI2
AUDIO
OUT
03
HDMI1
AUDIO
IN
RS232C
OUT
RS232C
IN
USB2
USB1
Reverse Side
Quick Setup Guide
01
02
05
06
PM32F·PM43F·PM49F·PM55F
PH43F·PH49F·PH55F
DP IN
07
01 Connect to a USB memory device.
02Connects to MDC using an RS232C adapter.
03Receives sound from a source device via an audio cable.
04Connects to the audio of a source device.
05Connects to a source device using an HDMI cable.
• The colour and the appearance may differ depending on the product, and the specifications are subject
to change without prior notice to improve the performance.
• Download the user manual from the website for further details.
http://www.samsung.com/displaysolutions
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are
trademarks or registered trademarks of HDMI Licensing LLC in the United States and other
countries.
Regulatory guide
MagicInfo Software DVD
Solutions
Issues
Solutions
The screen keeps switching
on and off.
Check the cable connection between the product
and PC, and ensure the connection is secure.
The screen is too bright.
The screen is too dark.
Adjust Brightness and Contrast.
No Signal is displayed on the
screen.
Check that the product is connected correctly with
a cable.
Screen color is inconsistent.
Go to Picture and adjust the Color Space settings.
White does not really look
white.
Go to Picture and adjust the White Balance settings.
There is no sound.
Check the connection of the audio cable or adjust
the volume.
Check that the device connected to the product is
powered on.
-
+
+
Batteries (Not available in some locations)
Remote Control
RS232C(IN) adapter
Not Optimum Mode is
displayed.
This message is displayed when a signal from the
graphics card exceeds the product’s maximum
resolution and frequency.
Refer to the Standard Signal Mode Table and set
the maximum resolution and frequency according
to the product specifications.
Screw (M3L8, 1 piece)
USB cover
The images on the screen
look distorted.
Check the cable connection to the product.
The screen is not clear.
The screen is blurry.
Adjust Coarse and Fine.
Remove any accessories (video extension cable,
etc) and try again.
Set the resolution and frequency to the
recommended level.
The screen appears unstable
and shaky.
There are shadows or ghost
images left on the screen.
[PMF_PM32~55-INDIA-QSG]BN68-08079J-00.indd 1
06DVI IN: Connects to a source device using a DVI cable or HDMI-DVI cable.
RGB IN: Use the (dedicated) D-SUB - DVI cable (or D-SUB cable with D-SUB to DVI
adapter) when connecting a PC.
MAGICINFO IN: Use the (dedicated) DP-DVI cable when connecting a network box
(sold separately).
07 Connects to a source device using a DP cable.
08Connects to another product using a daisy chain (DP port) cable.
09Connects to MDC using a LAN cable.
Issues
-
Power cord
09
Troubleshooting Guide
Contact the vendor where you purchased the product if any components are missing.
Warranty card (Not available in some
locations)
08
RJ45
BN68-08079J-00
Checking the Components
Quick Setup Guide
DAISY CHAIN
Check that the resolution and frequency of the
PC and graphics card are set within a range
compatible with the product. Then, change the
screen settings if required by referring to the
Additional Information on the product menu and
the Standard Signal Mode Table.
Check the volume.
The volume is too low.
Adjust the volume.
If the volume is still low after turning it up to the
maximum level, adjust the volume on your PC
sound card or software program.
The remote control does not
work.
Make sure that the batteries are correctly in place
(+/-).
Check if the batteries are flat.
Check for power failure.
Make sure that the power cord is connected.
Check for any special lighting or neon signs
switched on in the vicinity.
8/22/2016 4:22:33 PM
Connecting and Using a Source Device
Connecting to a PC
Specifications
Connecting to an Audio System
Model Name
PM32F
PM43F / PH43F
PM49F / PH49F
PM55F / PH55F
Size
80.1 cm
107.9 cm
123.2 cm
138.7 cm
Display area
698.4 mm (H) x 392.85 mm (V)
940.89 mm (H) x
529.25 mm (V)
1073.78 mm (H) x
604.00 mm (V)
1209.6 mm (H) x 680.4 mm (V)
Audio Output
10 W + 10 W
10 W + 10 W
10 W + 10 W
10 W + 10 W
Power Supply
AC 100 to 240 VAC (+/- 10%), 60 / 50 Hz ± 3 Hz
Refer to the label at the back of the product as the standard voltage can vary in different countries.
Panel
AUDIO OUT
DVI / RGB / MAGICINFO IN
AUDIO IN
Connecting the LAN Cable
Environmental
considerations
RJ45
Operating
Temperature: 0 ˚C - 40 ˚C (32 ˚F - 104 ˚F), With PIM: 10 ˚C - 40 ˚C (50 ˚F - 104 ˚F)
Humidity: 10% - 80%, non-condensing
Storage
Temperature: -20 ˚C - 45 ˚C (-4 ˚F - 113 ˚F)
Humidity: 5% - 95%, non-condensing
DVI / RGB / MAGICINFO IN
• This device is a Class A digital apparatus.
Use Cat7(*STP Type) cable for the connection.
* Shielded Twist Pair
AUDIO IN
Ⓡ
Ⓡ
Warning! Important Safety Instructions
Connecting to MDC
(Please read the appropriate section that corresponds to the marking on your Samsung product before attempting to install the product.)
CAUTION
RS232C IN
RISK OF ELECTRIC SHOCK DO NOT OPEN
HDMI1 or HDMI2
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR
BACK). THERE ARE NO USER SERVICEABLE PARTS INSIDE. REFER ALL SERVICING TO
QUALIFIED PERSONNEL.
RS232C OUT
RS232C IN
AUDIO IN
RS232C OUT
RS232C IN
RS232C OUT
HDMI1 or HDMI2
• If your equipment uses an AC adapter:
‒ Only use the AC adapter with your product by Samsung.
‒ Do not use the power cord with other products.
• Do not install this equipment in a confined space such as a case or similar.
• The slots and openings in the cabinet and in the back or bottom are provided for necessary
ventilation. The slots and openings must never be blocked or covered.
• The product should be located away from heat sources such as radiators, heat registers, or
other products that produce heat.
RJ45
HUB
This symbol indicates that high voltage is present inside. It is dangerous to
make any kind of contact with any internal part of this product.
This symbol alerts you that important literature concerning operation and
maintenance has been included with this product.
• Do not place a water containing vessel (vases etc.) on this apparatus, as this can result in a risk
of fire or electric shock. (Apparatus shall not be exposed to dripping or splashing)
• The apparatus must be connected to an earthed MAINS socket-outlet (Class l Equipment only).
Or Use only a properly grounded plug and receptacle (Class l Equipment only).
• To disconnect the apparatus from the mains, the plug must be pulled out from the mains
socket, therefore the mains plug shall be readily operable.
• As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power
source even if you turn off this unit by POWER.
This product is RoHS compliant.
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household
waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and
recycle
them responsibly to promote the sustainable reuse of material resources.
For more information on safe disposal and recycling visit our website www.samsung.com/in or contact our Helpline numbers -18002668282, 180030008282.
DP IN
Contact SAMSUNG WORLD WIDE
Connecting an External Monitor
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care centre.
Tel. 1800 3000 8282 - Toll Free
1800 266 8282 - Toll Free
www.samsung.com/in/support
DAISY CHAIN
RJ45
Connecting to a Video Device
HDMI1 or HDMI2
RS232C OUT
RS232C IN
RS232C OUT
RS232C IN
AUDIO IN
RS232C OUT
• For details on how to use the MDC programme, refer to Help after installing
the programme.
• The MDC programme is available on the website.
HDMI1 or HDMI2
[PMF_PM32~55-INDIA-QSG]BN68-08079J-00.indd 2
8/22/2016 4:22:35 PM
Download PDF