Samsung | UM55H-E | Samsung UM55H-E Quick start guide

Reverse Side
IR
OUT
2
CONTROL IN
1 Receives the remote control signal via the external sensor
board and outputs the signal via LOOP OUT.
2 Supplies power to the external sensor board or receives the
light sensor signal.
3 DVI IN: Connects to a source device using a DVI cable or HDMI-DVI
cable.
MAGICINFO: To use MagicInfo, make sure to connect the DP-DVI
cable.
DVI IN
(MAGICINFO)
Quick Setup Guide
1
3
HDMI IN 1
UH55F-E UM55H-E
4 Connects to a source device using an HDMI cable.
4
HDMI IN 2
5 Connects to a PC using a DP cable.
6 Connects to a source device using a D-SUB cable.
DP IN
5
7 Connects to another product using a DP cable.
RGB IN
6
7
0 Connects to MDC using an RS232C adapter.
AUDIO
! Connect to a USB memory device.
(Only for update purpose)
RS232C
IN
OUT
@ Connects to MDC using a LAN cable.
RJ45
USB
!
@
9 Connects to the audio of a source device.
IN
The terms HDMI and HDMI High-Definition Multimedia Interface,
and the HDMI Logo are trademarks or registered trademarks of
HDMI Licensing LLC in the United States and other countries.
OUT
8
9
0
8 Receives sound from a PC via an audio cable.
DP OUT
(LOOPOUT)
The colour and the appearance may differ depending on the product, and the specifications are
subject to change without prior notice to improve the performance.
Download the user manual from the website for further details.
http://www.samsung.com/displaysolutions
BN68-07486G-00
External sensor KIT
Checking the Components
- Contact the vendor where you purchased the product if any
components are missing.
- The pictures may look different from the actual components.
1
2
Troubleshooting Guide
Issues
Solutions
Issues
The screen keeps
switching on and off.
Check the cable connection between the
product and PC, and ensure the connection
is secure.
The screen is too bright.
Adjust Brightness and Contrast.
The screen is too dark.
No Signal is displayed
on the screen.
Check that the product is connected
correctly with a cable.
3
4
Check that the device connected to the
product is powered on.
5
Quick Setup Guide
Warranty card
MagicInfo Software
(Not available in some
DVD
locations)
Not Optimum Mode is
displayed.
1 Remote Control Sensor
Aim the remote control towards this spot on the LCD Display.
- Keep the area between the remote sensor and remote
control obstacle-free.
Power cord
Batteries
(Not available in some
locations)
Remote Control
2 Light sensor
Automatically detects the intensity of ambient light around a
selected display and adjusts the screen brightness.
3 Power indicator
The power indicator will turn off when the product is turned on.
It will blink in power-saving mode.
DP cable
RS232C(IN) adapter
UH55F-E_UM55H-E_INDIA_QSG_BN68-07486G-00.indd 1
Holder-Ring (4EA) /
Screw (4EA)
4 POWER button
Use this button for turning the LCD Display on and off.
5 SOURCE button
Switches from PC mode to Video mode.
Selects the input source that an external device is connected to.
The images on the
screen look distorted.
Set the resolution and frequency to the
recommended level.
There are shadows or
ghost images left on
the screen.
Go to Picture and adjust the White Balance
settings.
The product will turn
off automatically.
Go to System and make sure Sleep Timer is
set to Off.
If a PC is connected to the product, check
the power status of the PC.
Make sure the power cable is connected
properly to the product and power outlet.
If the signal from a connected device is not
detected, the product automatically turns
off after 10 to 15 minutes.
There is no sound.
Check the cable connection to the product.
The screen is not clear. Adjust Coarse and Fine.
The screen is blurry.
Remove any accessories (video extension
cable, etc) and try again.
The screen appears
unstable and shaky.
White does not really
look white.
This message is displayed when a
signal from the graphics card exceeds
the product’s maximum resolution and
frequency.
Refer to the Standard Signal Mode Table and
set the maximum resolution and frequency
according to the product specifications.
Check that the resolution and frequency of
the PC and graphics card are set within a
range compatible with the product. Then,
change the screen settings if required by
referring to the Additional Information on
the product menu and the Standard Signal
Mode Table.
Solutions
Check the connection of the audio cable or
adjust the volume.
Check the volume.
The volume is too low.
Adjust the volume.
If the volume is still low after turning it up
to the maximum level, adjust the volume on
your PC sound card or software programme.
The remote control
does not work.
Make sure that the batteries are correctly in
place (+/-).
Check if the batteries are flat.
Check for power failure.
Make sure that the power cord is connected.
Check for any special lighting or neon signs
switched on in the vicinity.
2017-08-08 오전 10:40:02
Connecting to a PC
Connecting the LAN Cable
Specifications
Model Name
UH55F-E / UM55H-E
Panel
Use Cat7(*STP Type) cable for the connection.
*Shielded Twist Pair
Size
138.7 cm
Display area
1209.6 mm (H) x 680.4 mm (V)
AC 100 to 240 VAC (+/- 10%), 60 / 50 Hz ± 3 Hz
Refer to the label at the back of the product as the standard voltage can vary in different countries.
Power Supply
Environmental
considerations
Connecting an External Monitor
Operating
Temperature: 0 ℃ - 40 ℃ (32 ℉ - 104 ℉)
Humidity: 10 % - 80 %, non-condensing
Storage
Temperature: -20 ℃ - 45 ℃ (-4℉ - 113℉)
Humidity: 5 % - 95 %, non-condensing
- This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to
take adequate measures.
To use old and new models together, first contact the dealer the
product was purchased from to check if they are compatible.
- For detailed device specifications, visit the Samsung Electronics website.
- The PVC Free (except for accessory cables) logo is the self-declared trademark of Samsung.
* Accessory cables: signal cables and power cords
Connecting to MDC
Warning! Important Safety Instructions
(Please read the appropriate section that corresponds to the marking on your Samsung product before attempting to install the product.)
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). THERE ARE NO USER SERVICEABLE
PARTS INSIDE. REFER ALL SERVICING TO QUALIFIED PERSONNEL.
» If your equipment uses an AC adapter:
- Only use the AC adapter with your product by
Samsung.
- Do not use the power cord with other products.
» Do not install this equipment in a confined space such as a case
or similar.
» The slots and openings in the cabinet and in the back or bottom
are provided for necessary ventilation. The slots and openings
must never be blocked or covered.
» The product should be located away from heat sources such as
radiators, heat registers, or other products that produce heat.
Connecting to a Video Device
This symbol indicates that high voltage is present
inside. It is dangerous to make any kind of contact
with any internal part of this product.
This symbol alerts you that important literature
concerning operation and maintenance has been
included with this product.
» Do not place a water containing vessel (vases etc.) on this
apparatus, as this can result in a risk of fire or electric shock.
(Apparatus shall not be exposed to dripping or splashing)
» The apparatus must be connected to an earthed MAINS socketoutlet (Class l Equipment only). Or Use only a properly grounded
plug and receptacle (Class l Equipment only).
» To disconnect the apparatus from the mains, the plug must be
pulled out from the mains socket, therefore the mains plug shall
be readily operable.
» As long as this unit is connected to the AC wall outlet, it is not
disconnected from the AC power source even if you turn off this
unit by POWER.
This product is RoHS compliant.
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger,
headset, USB cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other
types of waste and recycle them responsibly to promote the sustainable reuse of material resources.
For more information on safe disposal and recycling visit our website www.samsung.com/in or contact our Helpline numbers
- 1800 40 SAMSUNG(1800 40 7267864) (Toll-Free)
RS232C OUT
Connecting to an Audio System
UH55F-E_UM55H-E_INDIA_QSG_BN68-07486G-00.indd 2
For details on how to use the MDC programme, refer to Help after
installing the programme.
The MDC programme is available on the website.
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care centre.
Tel. 1800 40 SAMSUNG (1800 40 7267864) (Toll-Free)
www.samsung.com/in/support
2017-08-08 오전 10:40:04
Download PDF