BN68-00690A-00Eng 4/23/04 9:15 AM Page 8 Infrared Remote Control ENG TURNS THE PDP ON AND OFF DIRECT CHANNEL SELECTION TUNES TO THE PREVIOUS CHANNEL EXTERNAL INPUT SELECTION/ TELETEXT PAGE HOLD VOLUME INCREASE TEMPORARY SOUND SWITCH-OFF VOLUME DECREASE AUTOMATIC SWITCH-OFF/ TELETEXT STORE (DEPENDING ON THE MODEL) MENU DISPLAY/ TELETEXT INDEX NEXT CHANNEL/ TELETEXT NEXT PAGE PRESS TO SELECT ALL OF THE AVAILABLE VIDEO SOURCES/ TELETEXT MODE (LIST/FLOF) SELECTION (DEPENDING ON THE MODEL) PREVIOUS CHANNEL/ TELETEXT PREVIOUS PAGE INFORMATION DISPLAY/ TELETEXT REVEAL TV MODE SELECTION EXIT TELETEXT (DEPENDING ON THE MODEL) MOVE TO THE REQUIRED MENU OPTION/ ADJUST AN OPTION VALUE RESPECTIVELY CONFIRM YOUR CHOICE (STORE OR ENTER) SOUND MODE SELECTION/ TELETEXT SUB-PAGE PICTURE SIZE/ TELETEXT SIZE SELECTION TELETEXT DISPLAY/ MIX BOTH TELETEXT INFORMATION AND THE NORMAL BROADCAST PICTURE STILL/ TELETEXT CANCEL SOUND EFFECT SELECTION PICTURE EFFECT SELECTION ➢ The performance of the remote control may be affected by bright light. BN68-00690A-00Eng 4/23/04 9:16 AM Page 54 Connecting to the S-Video Input ENG The S-VIDEO and RCA (AUDIO-L/R) connectors are used for equipment with an S-Video output, such as a camcorder or VCR. Rear of the TV ① Camcorder and VCR ① To play picture and sound, both the S-VIDEO and RCA connectors must be used. ☛ Whenever you connect an audio or video system to your television, ensure that all elements are switched off. Refer to the documentation supplied with your equipment for detailed connection instructions and associated safety precautions. BN68-00690A-00Eng 4/23/04 9:16 AM Page 55 Connecting to the DVI Input ENG The “DVI” (video) and “L-AUDIO-R” connectors are used for equipment with a DVI output. Rear of the TV Personal Computer and Connecting to the PC Input The “RGB” (video) and “AUDIO” connectors are used for interfacing with your PC. Rear of the TV Personal Computer and BN68-00690A-00Eng 4/23/04 9:16 AM Page 56 Connecting to the Component Input ENG Rear of the TV DTV receiver DVD or ① The “COMPONENT” connectors are used for DTV receiver or DVD. (480i,p/576i,p/720p/1080i) BN68-00690A-00Eng 4/23/04 9:16 AM Page 57 Connecting and Using the Home Theater System ENG Use the Monitor Out ports of the PDP for Home Theater System Connections. Rear of the TV Connecting the Home Theater System ① Connect the monitoring audio out L, and R jacks of the MONITOR OUT on the rear-side connection panel of the PDP TV to the AUDIO IN jacks of the DVD Home Theater System (or AV Receiver) using the audio cable. ② Press the TV/VIDEO button to select the desired external device connected to the PDP TV. ③ If you want to hear the sound through separate speakers, cancel the internal amplifier. ② ① DVD Home Theater ☛ AV Receiver Amplifier ◆ Refer to corresponding user’s manual from the manufacturer for wiring the speakers to the DVD Home Theater System (or AV Receiver). ◆ Disable the PDP TV internal speaker to enjoy the rich sound through the speakers of your Home Theater System. ◆ In this case, enjoy the sound from the Home Theater System while the PDP TV does not produce the audio. To Display the DVD Home Theater ! Turn the PDP on and press the TV/VIDEO button to select the AV or Component. @ Be sure to connect the video cable properly if desired external input AV cannot be selected. # Play the DVD after activating the DVD Home Theater System. $ Use the volume control of the Home Theater System while watching the PDP using the DVD Home Theater, where the PDP TV does not produce the audio.