Samsung | PS-42P4H | Samsung PS-42P4H Quick start guide

BN68-00624A-02Eng_0422
5/11/04
3:43 PM
Page 7
Your New Plasma Display Panel
➢
The actual configuration on your PDP may be different,
depending on your model.
ENG
Side of the TV
S-Video Input
Video Input
Audio Input (L, R)
Rear Panel
➢
For further details about connection, refer to pages 51~55.
a) DVI INPUT (DVI-D / L-AUDIO-R)
Connect to the digital video and audio output jack
for device with DVI output.
g) AV1, AV2, AV3
(VIDEO / L-AUDIO-R )
Video and audio inputs for external devices, such
as a camcorder or VCR.
b) MONITOR OUT (VIDEO / L-AUDIO-R)
Outputs for external devices
c) ANT IN VHF/UHF (75Ω)
h) COMPONENT1, COMPONENT2
Video (Y/Pb/Pr) and audio (L-AUDIO-R) inputs for
Component.
75Ω Coaxial connector for Aerial/Cable Network.
i) POWER IN
d) PC INPUT (RGB IN / AUDIO)
Connect to the video and audio output jack on
your PC.
Connect the supplied power cord.
j) EXT SPEAKER (8Ω)
Connectors for external rear speakers.
e) ONLY FOR SERVICE
Connector for service only.
f) S-VIDEO1, S-VIDEO2
(S-VIDEO1 or S-VIDEO2 / L-AUDIO-R)
Video and audio inputs for external devices with
an S-Video output, such as a camcorder or VCR.
1
BN68-00624A-02Eng_0422
5/11/04
3:43 PM
Page 8
Infrared Remote Control
ENG
TURNS THE PDP ON AND OFF
WHEN YOU PRESS A BUTTON , ‘
’
APPEARS ALONG WITH SELECTED MODE
(TV, VCR, CATV, DVD OR STB) AND
REMAINING BATTERIES ON LCD
PICTURE EFFECT SELECTION
SOUND EFFECT SELECTION
TELETEXT CANCEL
MAKE THE REMOTE CONTROL WORKS
FOR TV, VCR, CATV, DVD PLAYER, STB
DIRECT CHANNEL SELECTION
AUTOMATIC SWITCH-OFF/
TELETEXT SUB-PAGE
PICTURE SIZE/
TELETEXT SIZE SELECTION
VOLUME INCREASE
TEMPORARY SOUND SWITCH-OFF
VOLUME DECREASE
TELETEXT DISPLAY/
MIX BOTH TELETEXT INFORMATION
AND THE NORMAL BROADCAST
MENU DISPLAY/
TELETEXT INDEX
NEXT CHANNEL/
TELETEXT NEXT PAGE/
EXTERNAL INPUT SELECTION/
TELETEXT PAGE HOLD
PREVIOUS CHANNEL/
TELETEXT PREVIOUS PAGE/
INFORMATION DISPLAY
TV MODE SELECTION
EXIT TELETEXT
(DEPENDING ON THE MODEL)
MOVE TO THE REQUIRED
MENU OPTION/
ADJUST AN OPTION VALUE
RESPECTIVELY
PICTURE STILL
DNIe ON/DEMO/OFF
FASTEXT TOPIC SELECTION
REMOTE CONTROL SETUP
IF YOUR REMOTE CONTROL IS NOT
FUNCTIONING PROPERLY, TAKE
OUT THE BATTERIES AND PRESS
THE RESET BUTTON FOR ABOUT
2~3 SECONDS. RE-INSERT THE
BATTERIES AND TRY USING THE
REMOTE CONTROL AGAIN.
➢
2
CONFIRM YOUR CHOICE
(STORE OR ENTER)
SOUND MODE SELECTION
TruSurround XT
MODE SELECTION
PIP FUNCTIONS;
- PIP ACTIVATING OR DEACTIVATING
(PIP ON)
- SWAPPING THE MAIN AND THE SUB
PICTURE (SWAP)
- LOCATION SELECTION (POSITION)
- SOURCE SELECTION (SOURCE)
- SIZE SELECTION (SIZE)
- SCAN
- SELECTING THE CHANNEL OF SUB
PICTURE (P
)
VCR/DVD FUNCTIONS;
- REWIND (REW)
- STOP
- PLAY/PAUSE
- FAST FORWARD (FF)
The performance of the remote control may be affected by bright light.
BN68-00624A-02Eng_0422
5/11/04
3:43 PM
Page 9
Inserting the Batteries in the Remote Control
ENG
You must insert or replace the batteries in the remote control when
you:
◆ Purchase the PDP
◆ Find that the remote control is no longer operating
correctly
1
Remove the cover on the rear of the remote control by pressing
the symbol ( ) downwards and then pulling firmly to remove it.
2
Insert two R03, UM4, “AAA” 1.5V or equivalent batteries taking
care to respect the polarities:
◆ - on the battery against - on the remote control
◆ + on the battery against + on the remote control
3
Replace the cover by aligning it with the base of the remote
control and pressing it back into place.
Assembling the Stand-Base
1
Assemble two support pins with the stand base and firmly secure
both sides of the support pins using 8 screws provided.
2
Assemble the PDP with the stand and firmly secure the PDP using
4 screws provided.
➢
◆ Two or more people should carry the PDP. Never lay the
PDP on the floor because of possible damage to the screen.
Always store the PDP upright.
(depending on your model)
The angle of the PDP can be up to 15
degrees left/right.
3
BN68-00624A-02Eng_0422
5/11/04
3:43 PM
Page 10
Installing the Display on the Wall Attachment Panel
ENG
Installation Notes
◆ Do not install the PDP on any place other than vertical walls.
◆ To protect the performance of the PDP and prevent troubles, avoid the followings:
- Do not install next to smoke and fire detectors.
- Do not install in an area subjected to vibration or high voltage.
- Do not install near or around any heating apparatus.
◆ Use only recommended parts and components.
Mounting Kits
Wall Mount Bracket
Plastic Hanger
Screws
4 EA
4 EA
How to Adjust Mounting Angle
(depending on your model)
The wall mount bracket is delivered
separately. Please tighten the captive
screw in the direction of the arrow after
assembling the bracket.
4
1
Secure the PDP to the wall mount bracket.
(Please refer to the following instructions.)
2
Set the angle by pulling the upper end of the
PDP attached to bracket in the direction of the
arrow.
3
The angle can be adjusted from 0° to 15° by
±2°.
BN68-00624A-02Eng_0422
5/11/04
3:43 PM
Page 11
Installing the Display on the Wall Attachment Panel (continued)
➢
The exterior of the PDP may be different than the picture.
(Assembly and installation of the plastic hanger is the same.)
1
Remove the screws from the back of the PDP.
2
ENG
Use the screws and assemble the plastic
hanger.
☛
◆ Please ask the installers to install the
wall mount bracket.
◆ Please be sure to check if the plastic
hanger is completely secured on both
the left and right side after hanging
the PDP on the wall mount bracket.
◆ Please avoid catching your fingers
while installing and adjusting the
angle.
◆ Please tightly secure the wall mount
bracket to the wall to avoid injury
from a falling PDP.
3
Tighten the screws of the plastic hanger to the
back side of the PDP.
4
Put the 4 pegs on the PDP in the grooves of the wall mount bracket and pull down on the PDP (!) to
secure it to the wall mount bracket (@). Tighten the screws as shown (#) so that the PDP cannot be
separated from wall mount bracket.
PDP panel
Wall attachment panel bracket
Wall
Connecting External Devices to the PDP
◆ To connect external devices such as a DVD or a Home Theater System to the PDP, please refer
to following instructions:
1
Be sure to remove the safety pins underneath the PDP.
◆ If the safety pins are not removed, the angle cannot be adjusted.
Any attempt to do so may cause damage to the PDP.
2
Pull out the bottom of the PDP (which has been attached to the Wall
Mount Bracket) in the direction indicated by the arrows (refer to
the illustration) until it clicks.
◆ Using the PDP After Connecting External Devices.
Be sure to secure the PDP by inserting the 2 safety pins after
o
readjusting the angle of the PDP to 0 .
◆ For safety, be sure to secure the PDP using the safety pins.
If the safety pins are not used, the PDP may fall, causing serious
injury.
5
BN68-00624A-02Eng_0422
5/11/04
3:43 PM
Page 12
Connecting to an Aerial or Cable Television Network
ENG
To view television channels correctly, a signal must be received by
the set from one of the following sources:
◆ An outdoor aerial
◆ A cable television network
◆ A satellite network
Rear of the PDP
or
Cable Television
Network
1
In the first three cases, connect the aerial or network input cable to
the 75Ω coaxial socket on the rear of the PDP.
2
If you are using an indoor aerial, you may need to turn it when
tuning your PDP until you obtain a picture that is both sharp and
clear.
For further details, refer to the user manual:
◆ “Storing Channels Automatically” on page 18
◆ “Storing Channels Manually” on page 19
➢
When installing or re-installing your PDP, be sure to use the
supplied coaxial antenna cable. If you connect using a different
coaxial cable, there is risk of noise or interference to the screen
image. (You must not use another general purpose cable.
Use the 3M/5M/7M cable supplied by Samsung.)
Connecting a Satellite Receiver or Decoder
Rear of the PDP
In order to watch television programmes broadcast via a satellite
network, you must connect a satellite receiver to the rear of the
PDP. Also, in order to descramble a coded transmission signal, you
must connect a decoder to the rear of the PDP.
or
Using a Coaxial cable
Connect a coaxial cable to the:
◆ Receiver (or Decoder) output socket.
◆ Television aerial input socket.
➢
If you wish to connect both a satellite receiver (or decoder)
and a VCR, you should connect the:
◆ Receiver (or Decoder) to the VCR
◆ VCR to the PDP
Otherwise, connect the receiver (or decoder) directly to the
PDP.
Satellite receiver/
Decoder
6
BN68-00624A-02Eng_0422
5/11/04
3:44 PM
Page 51
Connecting to the External Devices
ENG
“MONITOR OUT” are used for the equipment with an RGB output, such as
video game devices or video disc players.
VCR
②
DVD
Rear of the TV
(Input/Output)
①
Decoder /
Video game device
Video disc player
Satellite receiver
① This end can be fitted with:
③
◆ Three RCA connectors (VIDEO + AUDIO-L/R)
② If you have a second VCR and wish to copy cassettes tape, connect the source VCR to
“AV 1, AV 2, AV 3” and the target VCR to “MONITOR OUT” so that you can redirect the signal from
“AV 1, AV 2, AV 3” to “MONITOR OUT”.
③ When you wish to record a programme, connect the receiver to “AV 1, AV 2, AV 3” and the VCR to
“MONITOR OUT” so that you can redirect the signal from “AV 1, AV 2, AV 3” to “MONITOR OUT”.
Rear of the TV
(Input/Output)
Camcorder
Video disc player
Video game device
7
BN68-00624A-02Eng_0422
5/11/04
3:44 PM
Page 52
Connecting to the S-Video Input
ENG
The S-VIDEO1 and RCA (AUDIO-L/R) connectors are used for equipment with an S-Video output,
such as a camcorder or VCR.
Rear of the TV
①
and
Camcorder
Side of the TV
①
VCR
and
① To play picture and sound, both the S-VIDEO and RCA connectors must be used.
☛
8
Whenever you connect an audio or video system to your television,
ensure that all elements are switched off. Refer to the documentation
supplied with your equipment for detailed connection instructions
and associated safety precautions.
BN68-00624A-02Eng_0422
5/11/04
3:44 PM
Page 53
Connecting to the DVI Input
ENG
The “DVI” (video) and “L-AUDIO-R” connectors are used for equipment with a DVI output.
Rear of the TV
Personal Computer
and
Connecting to the PC Input
The “RGB” (video) and “AUDIO” connectors are used for interfacing with your PC.
Rear of the TV
Personal Computer
and
9
BN68-00624A-02Eng_0422
5/11/04
3:44 PM
Page 54
Connecting to the Component Input
ENG
Rear of the TV
① The “COMPONENT 1” connectors are
①
DVD
②
DTV receiver
used for equipment with a DVD output.
(480i/480P/576i/576P/720P/1080i)
② The “COMPONENT 2” connectors are
used for DTV receiver.
(480i/480P/576i/576P/720P/1080i)
10
BN68-00624A-02Eng_0422
5/11/04
3:44 PM
Page 55
Connecting and Using the Home Theater System
ENG
Use the Monitor Out ports of the PDP for Home Theater System Connections.
Rear of the TV
Connecting the Home Theater System
① Connect the monitoring audio out L, and
R jacks of the MONITOR OUT on the
rear-side connection panel of the PDP
TV to the AUDIO IN jacks of the DVD
Home Theater System (or AV Receiver)
using the audio cable.
② Press the SOURCE button to select the
desired external device connected to the
PDP TV.
③ If you want to hear the sound through
separate speakers, cancel the internal
amplifier.
②
①
DVD Home Theater
☛
AV Receiver Amplifier
◆ Refer to corresponding user’s manual from the manufacturer for wiring the
speakers to the DVD Home Theater System (or AV Receiver).
◆ Disable the PDP TV internal speaker to enjoy the rich sound through the
speakers of your Home Theater System.
◆ In this case, enjoy the sound from the Home Theater System while the PDP TV
does not produce the audio.
To Display the DVD Home Theater
! Turn the PDP on and press the SOURCE button to select the AV1 (or AV2, AV3,
Component1, Component2).
@ Be sure to connect the video cable properly if desired external input (AV1, AV2, AV3,
Component1, or Component2) cannot be selected.
# Play the DVD after activating the DVD Home Theater System.
$ Use the volume control of the Home Theater System while watching the PDP using the DVD
Home Theater, where the PDP TV does not produce the audio.
11
BN68-00624A-02Eng_0422
5/11/04
3:45 PM
Page 56
Installing the Speakers
➢
ENG
This speaker installation guide is for the 4240 Model.
Parts
How to Assemble the Speakers(Standing)
The actual product may differ
slightly from the illustration.
① Remove the screws indicated on the rear of the PDP (6 screws on
the left and right sides).
Speakers
2 EA
② Attach the Bracket Pads to the Speaker’s Guide Bracket.
Set the Speaker Guide Bracket into the square grooves located on
either side of the PDP’s bottom rear and secure it with the provided
screws ①, ➁. (Always use the proper screws, as indicated.)
Middle Cabinet
(Wall Mount Only)
Bracket Pads
1 EA
Screw①
Screw②
Speaker Dust Cover
③ Secure the Speaker Dust Cover by setting it into the grooves
located on the front side of the speakers.
1 EA
Speaker Cable
④ Connect the speakers to the PDP using the speaker cable.
The connection terminals are on the rear side of both the PDP and
the speakers. (Match the color coded terminals and cables.)
Screws
BLACK
Screw①
: 6EA
RED
BLACK RED
Screw➁
: 4EA
WARNING
Bracket Pads
1. When moving the PDP with the speakers attached, be sure to hold on to the PDP
to prevent damage. (Damage may occur to the speaker connecting brackets or
the speakers.)
3 EA
12
2. Speakers of 8Ω Impedance, 15W Nom. Power, 30W Max. Power is recommended.
BN68-00624A-02Eng_0422
5/11/04
3:46 PM
Page 57
Installing the Speakers (continued)
ENG
Parts
How to Assemble the Speakers(Wall Mount)
The actual product may differ
slightly from the illustration.
① Remove the screws indicated on the rear of the PDP (6 screws on the
left and right sides, 2 screws on the center).
Speakers
2 EA
② Attach the Bracket Pads to the Speaker’s Guide Bracket.
Set the Speaker Guide Bracket into the square grooves located on
either side of the PDP’s bottom rear and secure it with the provided
screws ①, ➁. Secure the Middle Cabinet to the center of the PDP
with a screw ①. (Always use the proper screws, as indicated.)
Middle Cabinet
(Wall Mount Only)
Bracket Pads
1 EA
Speaker Dust Cover
Screw①
Screw②
③ Secure the Speaker Dust Cover by setting it into the grooves
located on the front side of the speakers.
1 EA
Speaker Cable
④ Connect the speakers to the PDP using the speaker cable.
The connection terminals are on the rear side of both the PDP and
the speakers. (Match the color coded terminals and cables.)
Screws
BLACK
Screw①
: 6EA
RED
BLACK RED
Screw➁
: 4EA
WARNING
Bracket Pads
1. When moving the PDP with the speakers attached, be sure to hold on to the PDP
to prevent damage. (Damage may occur to the speaker connecting brackets or
the speakers.)
3 EA
2. Speakers of 8Ω Impedance, 15W Nom. Power, 30W Max. Power is recommended.
13
Download PDF