Samsung MX-FS9000 User Manual

Samsung MX-FS9000 User Manual
MX-FS9000
PREMIUM HI-FI Component System
MP3/WMA/CD-DA Playback with CD/USB
user's manual
Imagine the possibilities
Thank you for purchasing this Samsung product.
To receive a more complete service,
please register your product at
www.samsung.com/register
MX-FS9000-XU-ENG_130927.indd 1
2013-09-27 �� 1:39:45
Safety Warnings
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK).
NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This symbol indicates “dangerous voltage” inside CAUTION : TO PREVENT ELECTRIC SHOCK, This symbol indicates important instructions
the product that presents a risk of electric shock or MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY accompanying the product.
personal injury.
INSERT.
WARNING
• To reduce the risk of fire or electric shock, do not
expose this appliance to rain or moisture.
CAUTION
• Apparatus shall not be exposed to dripping or splashing
and no objects filled with liquids, such as vases, shall be
placed on the apparatus.
• The Mains plug is used as a disconnect device and shall
stay readily operable at any time.
• Use only a properly grounded plug and receptacle.
-- An improper ground may cause electric shock or
equipment damage. (Class l Equipment only.)
• CLASS 3B VISIBLE AND INVISIBLE LASER RADIATION
WHEN OPEN. AVOID EXPOSURE TO THE BEAM (IEC
60825-1)
• THIS PRODUCT UTILIZES A LASER. USE OF
CONTROLS OR ADJUSTMENTS OR PERFORMANCE
OF PROCEDURES OTHER THAN THOSE SPECIFIED
HEREIN MAY RESULT IN HAZARDOUS RADIATION
EXPOSURE. DO NOT OPEN COVER AND DO NOT
REPAIR YOURSELF. REFER SERVICING TO QUALIFIED
PERSONNEL.
CLASS 1
KLASSE 1
LUOKAN 1
KLASS 1
PRODUCTO
LASER PRODUCT
LASER PRODUKT
LASER LAITE
LASER APPARAT
LÁSER CLASE 1
CLASS 1 LASER PRODUCT
This Compact Disc player is classified as a CLASS 1
LASER product.
Use of controls, adjustments or performance of
procedures other than those specified herein may result in
hazardous radiation exposure.
DANGER :
• Complies with 21CFR 1040.10 except for deviations
pursuant to Laser Notice No. 50, dated June 24, 2007
• VISIBLE AND INVISIBLE LASER RADIATION WHEN
OPEN. AVOID DIRECT EXPOSURE TO BEAM. (FDA 21
CFR)
Wiring the Main Power Supply Plug (UK Only)
IMPORTANT NOTICE
The mains lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated on the pin
face of the plug and if it requires replacing, a fuse approved to BS1362 of the same rating must be used. Never use the plug with the
fuse cover removed. If the cover is detachable and a replacement is required, it must be of the same colour as the fuse fitted in the plug.
Replacement covers are available from your dealer. If the fitted plug is not suitable for the power points in your house or the cable is not
long enough to reach a power point, you should obtain a suitable safety approved extension lead or consult your dealer for assistance.
However, if there is no alternative to cutting off the plug, remove the fuse and then safely dispose of the plug. Do not connect the plug to
a mains socket as there is a risk of shock hazard from the bared flexible cord. Never attempt to insert bare wires directly into a mains
socket. A plug and fuse must be used at all times.
IMPORTANT
The wires in the mains lead are coloured in accordance with the following code:– BLUE = NEUTRAL BROWN = LIVE As these
colours may not correspond to the coloured markings identifying the terminals in your plug, proceed as follows:–The wire
coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK. The wire coloured
BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED.
WARNING : DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL WHICH IS MARKED WITH LETTER E OR BY THE EARTH
, OR COLOURED GREEN OR GREEN AND YELLOW.
SYMBOL
2
English
MX-FS9000-XU-ENG_130927.indd 2
2013-09-27 �� 1:39:45
Important Information on Use
Precautions
• Ensure that the AC power supply in your house complies
with the identification sticker located on the back of your
product.
• Install your product horizontally, on a suitable base (furniture),
with enough space around it for ventilation (7.5~10cm).
• Do not place the product on amplifiers or other equipment
which may become hot. Make sure the ventilation slots are
not covered.
• Do not stack anything on top of the product.
• Before moving the product, ensure the Disc Insert Slot is
empty.
• To turn off the product completely, disconnect the AC plug from
the wall outlet. Disconnect the AC plug from the wall outlet if
you will leave the device unused for a long period of time.
• During thunderstorms, disconnect the AC plug from the wall
outlet. Voltage peaks due to lightning could damage the
product.
• Do not expose the product to direct sunlight or other heat
sources. This could cause the product to overheat and
malfunction.
• Protect the product from moisture, and excess heat or
equipment creating strong magnetic or electric fields (i.e.
speakers.).
• Disconnect the power cable from the AC supply if the
product malfunctions.
• Your product is not intended for industrial use. It is for
personal use only.
• Condensation may occur if your product or disc has been
stored in cold temperatures. If transporting the product
during the winter, wait approximately 2 hours until the
product has reached room temperature before using.
• The batteries used with this product contain chemicals that are harmful to the environment. Do not dispose of batteries in the general household trash.
• Maintain an open space of approximately 15 cm on the sides and rear of the system, for ventilation purposes.
• Place the loudspeakers at a reasonable distance on either side of the system to ensure good stereo sound.
• Direct the loudspeakers towards the listening area.
Cautions On Handling And Storing Discs
Small scratches on the disc may reduce sound and picture
quality or cause skipping.
Be especially careful not to scratch discs when handling
them.
Holding Discs
• Do not touch the playback side of the disc.
• Hold the disc by the edges so that fingerprints will not get
on the surface.
• Do not stick paper or tape on the disc.
Disc Storage
• Do not keep in direct sunlight.
• Keep in a cool ventilated area.
• Keep in a clean protective jacket.
Store vertically.
• Do not allow the discs to become contaminated with dirt.
• Do not load cracked or scratched discs.
Handling and Storing Discs
If you get fingerprints or dirt on a disc, clean it with a mild
detergent diluted in water and wipe with a soft cloth.
• When cleaning, wipe gently from the inside to the outside of
the disc
• Condensation may form if warm air comes into contact
with cold parts inside the product. When condensation
forms inside the product, it may not operate correctly. If this
occurs, remove the disc and let the product stand for 1 or
2 hours with the power on.
Disc Types And Disc Format
This product does not support Secure (DRM) Media files.
CD-R Discs
• Some CD-R discs may not be playable depending on
the disc recording device (CD-Recorder or PC) and the
condition of the disc.
• Use 650MB/74 minute CD-R discs.
Do not use CD-R discs over 700MB/80 minutes as they
may not be played back.
• Some CD-RW (Rewritable) media may not be playable.
• Only CD-Rs that are properly "closed" can be fully played. If
the session is closed, but the disc is left open, you may not
be able to fully play the disc.
CD-R MP3/WMA Discs
• Only CD-R discs with MP3 files in ISO 9660 or Joliet format
can be played.
• MP3 file names should contain no blank spaces or special
characters (. / = +).
• Use discs recorded with a compression/decompression
data rate greater than 128Kbps.
• Only files with the ".mp3" and ".wma" extensions can be
played.
• Only a consecutively written multisession disc can be
played. If there is a blank segment in the Multisession disc,
the disc can be played only up to the blank segment.
• If the disc is not closed, it will take longer to begin playback
and not all of the recorded files may play.
• For files encoded in Variable Bit Rate (VBR) format, i.e. files
encoded in both low bit rate and high bit rate (e.g., 32Kbps
~ 320Kbps), the sound may skip during playback.
• A maximum of 999 files can be played per CD.
• Supported Audio Formats (Bit Rate):WMA 56~128kbps,
MP3 80~320kbps
English
MX-FS9000-XU-ENG_130927.indd 3
3
2013-09-27 �� 1:39:46
Contents
Contents
Thank you for buying this SAMSUNG Hi-Fi-Component system.
Please take time to read these instructions.
They will allow you to operate your system with ease and take full advantage of its features.
Move FOLDER....................................... 12
How to safely remove the USB device....... 12
Read Before Using the USB Storage
Devices.................................................. 12
Bluetooth...................................................... 12
What is Bluetooth?................................. 12
To connect the Hi-Fi Component to a
Bluetooth device.................................... 12
To disconnect the Bluetooth device from
Hi-Fi Component.................................... 13
To disconnect the Hi-Fi Component
from the Bluetooth device...................... 13
Using My Karaoke........................................ 13
10 Skip Function........................................... 14
Auto Change Function.................................. 14
Listening to the Radio................................... 14
To Store the Stations You Want.............. 14
Selecting a Stored Station...................... 14
Safety Warnings.................................................. 2
Important Information On Use........................... 3
Precautions..................................................... 3
Cautions On Handling And Storing Discs
....................................................................... 3
Disc Types And Disc Format........................... 3
Accessories......................................................... 4
Description.......................................................... 5
Front Panel..................................................... 5
Rear Panel...................................................... 6
Remote Control.............................................. 7
Installing Batteries In The Remote
Control..................................................... 7
Connecting the Speakers............................... 8
Attacking the speaker feet.............................. 8
Basic Functions.................................................. 9
The Display function....................................... 9
Playing CDs.................................................... 9
Loading a Compact Disc.......................... 9
CD/MP3/WMA-CD Playback................... 9
Selecting a Track.................................... 10
Searching for a Track/Folder Quickly...... 10
Searching for a Specific Music Passage
on a CD.................................................. 10
Repeat One or All Tracks on a CD.......... 10
A-B Repeat Playback............................. 10
CD Programming................................... 10
Viewing or Editing the Programmed
Track...................................................... 11
Playing USB Devices.................................... 11
Before you begin!................................... 11
To Select a File from a USB Device........ 11
To Use High Speed Search.................... 11
To Delete a File....................................... 11
To Skip Next 10 Files.............................. 12
Symbols
Advanced Functions......................................... 15
Timer Function.............................................. 15
Setting the Clock.................................... 15
Setting the Timer.................................... 15
Cancelling the Timer............................... 16
The Recording Function................................ 16
Basic Recording..................................... 16
Recording Speed................................... 17
Special Sound Effect.................................... 17
Selecting EQ Mode................................ 17
Using the FOOTBALL Mode................... 17
GIGA SOUND Function.......................... 17
BEAT WAVING Function......................... 18
DJ BEAT Function.................................. 18
Booting Sound Function......................... 18
Troubleshooting................................................ 19
Specifications ................................................... 20
Important
Note
Accessories
Check for the supplied accessories below.
USB
CD/
AH59-02553A
User's Manual
Remote Control/ Batteries
FM Antenna
Power Cable
FOOT Rubber
• Figures and illustrations in this User's Manual are provided for reference only and may differ from actual product
appearance.
4
English
MX-FS9000-XU-ENG_130927.indd 4
2013-09-27 �� 1:39:47
Description
Front Panel
1
2
3
4
5
6
7
8
9
10
11
12
13
33
32
14
15
16
31
17
30 29 28 27 26 25 24 23 22 21
20
19
18
1. DELETE button
20.REMOTE CONTROL SENSOR
2. EASY SEARCHING JOG
21.BACKWARD SEARCH/SKIP button
3. DISPLAY/ DEMO button
22.AUX IN 1 jack
Connecting an external device such as an MP3
player.
4. STOP button
5. CD/ Bluetooth button
6. Display Panel
7. PLAY/PAUSE button
8. TUNER/AUX button
9. +PANNING button for DJ BEAT sound effect
• Connect AUX IN 1 on the front panel of the
product to the Audio Out of the external
device/MP3 player.
• Press the TUNER/AUX button to select the
AUX1.
10. MASTER VOLUME/DJ JOG control
23. MIC jack
11. CHORUS button for DJ BEAT sound effect
24. ENTER button
12. BEAT WAVING button
25. USB 2 SELECT button
13. POWER button
•Press this button to switch your product on or
off.
14. EJECT button
15. FLANGER button for DJ BEAT sound effect
16. DJ BEAT button
17. DISC slot
18. WAHWAH button for DJ BEAT sound effect
19. FORWARD SEARCH/SKIP button
26. USB 2 jack for Playing and USB Recording
27. USB REC button
28. USB 1 jack for only Playback
29. USB 1 SELECT button
30. RETURN button
31. FOOTBALL MODE button
32. GIGA SOUND BEAT button
33. EQ button
English
MX-FS9000-XU-ENG_130927.indd 5
5
2013-09-27 �� 1:39:48
Description
Rear Panel
7
6
1
2 3
4
5
1. FM Antenna Connector Terminal
1. Connect the FM antenna to the FM antenna connector terminal.
2. Slowly move the antenna wire until you find a
location where reception is good, then fasten it to
a wall or other rigid surface.
3. If reception is poor, you may need to install an
outdoor antenna. To do so, connect an outdoor
FM antenna to the FM antenna connector terminal
of the product using a 75Ω coaxial cable (not
supplied).
2. ONLY FOR SERVICE
• This jack is just for testing. Do not use.
3. AUX IN 2 Terminals
1. Use an Audio Cable (not supplied) to connect AUX
IN 2 on the product to Audio Out on an external
analogue output device.
• Be sure to match connector colours.
4. LED Terminals for Speaker Beat Waving.
5. 2.2 CH Speaker Terminals
1. To achieve the correct sound quality, when you connect the speakers, match the colour of the speaker
plugs to the colour of the speaker jacks. See below.
• LEFT channel (marked L , White/Purple).
• RIGHT channel (marked R , Red/Purple).
• Don't force the Purple SUBWOOFER connector
into the White or Red speaker jack.
6. POWER
• Insert only the provided power cable.
7. Cooling fan
• The fan operates while the unit is powered on.
If you set the unit to the minimum volume, the fan
won't operate.
Provide a minimum of 10 cm of clear space in
front of the fan when you install the product.
• If the external analogue output device has only one
Audio Out jack, connect either left or right.
• Press the TUNER/AUX button to select the AUX 2.
• If no button actions for more than 8 hours in AUX
mode, the power will automatically turn off.
6
English
MX-FS9000-XU-ENG_130927.indd 6
2013-09-27 �� 1:39:52
Description
Remote Control
30
1
29
USB
2
3
CD/
28
4
5
6
27
7
8
9
10
11
12
26
13
21
20
19
14
15
16
17
25
24
23
22
AH59-02553A
1.
2.
3.
4.
POWER
TUNER/AUX
USB
Number(0~9) button
During playback, press the
desired track number. The
selected track is played.
17.
18.
19.
20.
21.
MY KARAOKE
MIC VOLUME -, +
USB REC
DELETE
M
ono/Stereo for FM, CD
REC SPEED for CD
Ripping
5.
6.
7.
8.
9.
10.
SKIP (-10, +10)
SKIP
STOP
PLAY
REPEAT
GIGA
11.
12.
13.
14.
15.
16.
ENTER
VOLUME (-,+)
TUNING MODE
TIMER ON/OFF
TIMER SET
SLEEP
Set a sleep time to shut
off the product.
22.
23.
24.
25.
26.
27.
28.
29.
30.
TUNING/ALBUM ,,.
EQ
AUTO CHANGE
REPEAT A-B
PAUSE
SEARCH
CD/Bluetooth
BEAT WAVING
MUTE
Turn off the sound
temporarily. Press again to
turn the sound back on.
18
Installing Batteries In The Remote Control
`` Place batteries in the remote control so they match the polarity : (+) to (+) and
(–) to (–).
`` Do not dispose of batteries in a fire.
`` Do not short circuit, disassemble or overheat the batteries.
`` Danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type.
`` The remote control can be used up to approximately 23 feet (7 meters) in a
straight line from the system.
* Battery size: AAA
English
MX-FS9000-XU-ENG_130927.indd 7
7
2013-09-27 �� 1:39:54
Description
Connecting the Speakers
Recommended speaker setup.
☛ The product may not operate properly if not installed in accordance with recommended speaker
setup, or exposed to shaking or external shocks.
☛ Do not stretch the speaker wires or place a heavy object on them.
Attaching the speaker feet
Attach the supplied speaker feet to the bottom rear corner of each speaker to stabilize the speakers
and to prevent them from slipping.
FOOT Rubber
8
English
MX-FS9000-XU-ENG_130927.indd 8
2013-09-27 �� 1:40:01
Basic Functions
The Display function
You can view all functions available on the display, adjust the brightness of the display and set
the Display/LED either on or off.
Each time you press the DISPLAY/DEMO button,
the display mode will change as follows:
◆◆ The Dimmer function
The Dimmer function is selected and the display darkens.
◆◆ LED OFF
The LED is turned off while the dimmer function is working.
◆◆ Clock ON
The clock you set is displayed.
◆◆ Display/LED ON
All displays and the LED are turned on.
➣➣The DEMO Music function
ress DISPLAY/DEMO button for 5 seconds to play
P
demo music.
When you press the DISPLAY/DEMO button, the
function operates as follows:
DIMMER ➝ LED Off (unit/speaker) ➝ --:-- [time display] ➝ LED On (unit/speaker)
-- To cancel the Demo Music mode
• Press the DISPLAY/DEMO button for 5 seconds. The
current mode is canceled and the product is turned off.
•Press the TUNER/AUX, CD/Bluetooth or USB button.
The current mode is cancelled and the mode is
changed to the mode you selected.
-- While playing DEMO Music, all buttons will not work
except [Power], VOL,
[MUTE] and buttons
mentioned above.
-- If you connect speaker to AUX1 while displaying
DEMO, sound is produced through AUX1 and you
can use the VOL buttons and
[MUTE].
Playing CDs
CD/MP3/WMA-CD Playback
☛☛This product is designed to play the following audio
disc types: CD, CD-R, CD-RW, MP3/WMA-CD.
1. Insert a disc gently into the disc slot with the disc's
label facing up.
2. The disc will be played automatically.
• For MP3/WMA-CD audio, it may take several minutes
for the product to finish scanning the disc tracks.
• If you play a file with an English name or an MP3/
WMA-CD file with an English title, the song title will be
shown in the display. (Titles in other languages will not
be displayed.)
• An English-titled track containing a special character
will not be displayed.
<CD Playback Display>
. ya l ps i
Track Indicator
Playtime Indicator
3. To adjust the volume:
• Turn the VOLUME control on the product.
• P
ress the VOL + or VOL - button of the remote
control.
The volume level can be adjust in 31 steps (VOLUME
MIN, VOLUME01~ VOLUME 29, and VOLUME MAX).
4. Main Unit
To pause playback temporarily, press the p button.
Press p again to continue playing the disc.
Remote control
To pause playback temporarily, press the PAUSE(#) button.
Press the PLAY (+) button to continue playing the disc.
5. To end playing, press the STOP (@) button.
• If no CD is in the disc slot, “NO DISC” appears on the
display.
• The quality of MP3/WMA-CD playback may vary
depending on the condition of the disc or the condition of
the recorder with which the disc was created.
Loading a Compact Disc
• If a disc contains different types of files or unnecessary
folders, you will have problems with playback.
You can play standard CDs that require no adapter.
• Gently insert a CD into the disc slot. Do not apply
excessive force.
1. Insert a disc gently into the disc slot with the disc's
label facing up. The disc will be played automatically.
• You can load or unload compact discs when the
radio, USB or auxiliary source function is selected.
When you press the EJECT button, all of the other
functions will change to the CD mode.
• If no buttons are pressed on the product or remote
control for more than 3 minutes when the product is
in Pause mode, it will change to Stop mode.
• If no buttons are pressed on the product or remote
control for more than 25 minutes when the product
is in Stop mode, the product will turn off.
• Do not apply force to the product or place a heavy object
on the product.
• Do not insert an out-of-spec or oddly shaped CD (heart
shaped, octangular, etc.). You can damage the product.
• Carefully maintain your CDs.
English
MX-FS9000-XU-ENG_130927.indd 9
9
2013-09-27 �� 1:40:02
Basic Functions
Selecting a Track
You can select a desired track while the disc is
being played.
To play the previous track
Press the [ button within 3 seconds after the current
track has started playing.
Press the [ button twice at least 3 seconds after the
current track has started playing.
To play the next track
Press the ] button.
To play the current track from the beginning
Press the [ button 3 seconds after the current track
track has started playing.
To play the track of your choice
Press the [ or ] button to move to a desired track.
• You can also use the number ( 0~9 ) buttons on
the remote control to select a track.
Searching for a Track/Folder Quickly
You can select a track/folder directly without
the [, ] buttons.
CDDA/MP3-CD/WMA-CD
1. T
urn the EASY SEARCHING JOG on the product
to the left or right to select a desired track.
• You can move to the selected track directly.
2. When searching is done, the track will automatically
start playing.
Searching for a Specific Music Passage on
a CD
When listening to a CD, you can quickly search
for a specific music passage on a track.
Forward Search............................. )
Backward Search.......................... (
You can also press and hold the [, ] buttons on
the product to automatically scan for a track.
Repeat One or All Tracks on a CD
You can repeatedly play a track, a group of
tracks, or an entire CD.
1. P
ress the REPEAT button on the remote
control.
Each time you press the REPEAT button, the
repeat mode will change as follows:
FF ➝ TRACK ➝ DIR ➝ ALL ➝ RANDOM
MP3: O
CD: OFF ➝ TRACK ➝ ALL ➝ RANDOM
2. When
you want to stop the repeat function,
press the REPEAT button until "OFF" is
displayed.
• OFF: Cancels repeat playback.
• TRACK: Repeatedly plays the selected track.
• DIR (DIRECTORY): Repeatedly plays all tracks
in the selected directory.
• ALL: Repeatedly plays the entire disc.
• RANDOM: Plays tracks in random order.
A-B Repeat Playback
You can repeatedly play back a designated
section of a CD.
1. Press the REPEAT A-B button at the beginning
of desired part.
• 'RPT A' will be displayed.
2. Press the REPEAT A-B button at the ending of
desired part.
• 'RPT AB' will be displayed.
3. T
o cancel REPEAT A-B function, press the
REPEAT A-B button again.
• 'OFF' will be displayed.
The REPEAT A-B function is available within a
track.
➣➣
CD Programming
This function is not available during playback of an
MP3/WMA-CD.
• You can program the playback order of up to 24
tracks of your choice.
• However, you must stop playing the CD before
selecting tracks.
1. While in CD playback mode, press the STOP
(@) button to stop playing the CD.
2. Press the ENTER (
message below:
) button to display the
(01= program number, ---= track number)
10
English
MX-FS9000-XU-ENG_130927.indd 10
2013-09-27 �� 1:40:02
Basic functions
3. Use the [ or ] button to move to a desired
track.
• Press [ to move to the previous track.
• Press ] to move to the next track.
) button to confirm your
4. Press the ENTER (
selection. The selection is stored and
is displayed.
5. To select another track, follow Steps 3 and 4
above.
6. Press the PLAY (+) button to play the
programmed tracks.
7. Press the STOP (@) button to stop playing the
programmed tracks, Press the STOP (@) button
again to cancel playing the programmed tracks.
• If you eject the disc or turn off the product
or change other function mode, your
programming will be cancelled.
Viewing or Editing the Programmed Track
You can view a list of programmed tracks and
edit them as you want.
1. If a programmed track is being played, press
the STOP (@) button once.
2. Press the ENTER (
the message below:
) button twice to display
(01= program number, 002= track number)
3. Repeatedly press the ENTER (
the desired track is displayed.
) button until
4. Press the [ or ] button to select a different
track.
5. Press the ENTER (
selection.
) button to confirm your
6. To play the programmed tracks, press the Play
(+) button.
Playing USB Devices
Connect an external storage device such as a USB
flash memory or external HDD (Hard Disk Drive) to
the product. You can play files in MP3/WMA format.
Before you begin!
1. Connect the external USB storage device to your
product.
2. Select the USB mode by pressing the USB 1 or USB 2
button on the product or the USB button on the remote
control.
3. The first file of the first directory plays automatically.
4. T
o stop playing
Press the Stop ( @ ) button to stop playing.
➣➣To remove the USB device
If you press the Stop ( @ ) button once
again, you can remove the USB device safely.
☛☛Do not connect a USB recharger to the USB port
of this product. You can damage the product.
To Select a File from a USB Device
You can select an MP3 file while the product is
playing.
f you want to move to the previous/next track, press
➣➣Ithe
[,] buttons briefly.
• The unit moves to the previous/next file within the
directory.
• If you press the [,] buttons more times than the
number of the files in the directory, the unit moves to
the next directory.
To repeat
1. P
ress the REPEAT button.
Each time you press the REPEAT button, the repeat
mode will change as follows::
OFF ➝ TRACK ➝ DIR ➝ ALL ➝ RANDOM
2. W
hen you want to stop the repeat function, press the
Repeat button until "OFF" is displayed.
• OFF: Cancels repeat playback.
• TRACK: Repeatedly plays the selected file.
• DIR(DIRECTORY): Repeatedly plays all files in the
selected folder.
• ALL: Repeatedly plays all files.
• RANDOM: P
lays files in random order.
To Use High Speed Search
You can search the desired section quickly while
the product is playing.
1. Press the (,) button.
• Each time you press the button, you will move
forward/backward fast.
☛☛Sound does not output during a high speed search.
To Delete a File
You can delete a file from your USB device.
1. Select a file you want to delete.
2. Press the DELETE button.
3. Press the [,] buttons on the product or remote
control to select YES/NO.
• To cancel the selection, press the REtuRN button on
the product.
English
MX-FS9000-XU-ENG_130927.indd 11
11
2013-09-27 �� 1:40:03
Basic Functions
4. Press the ENTER button on the remote control.
The selected file will be deleted.
☛☛The NTFS file system is not supported.
To Skip Next 10 Files
1. Press the +10 or -10 button while in playback mode.
The unit will skip as many as 10 tracks forward or 10
tracks back from the current track.
Move FOLDER
Press the remote control's TUNING/ALBUM ,, . button
to move to the previous/next folder.
How to safely remove the USB device
1. Press the (@) button twice while the USB is playing or
press the (@) button once when play is stopped.
2. When the REMOVE message appears on the display,
remove the USB device.
Read Before Using the USB Storage Devices
• Some USB devices may not work properly with this
product.
• This product only supports external HDD's that are
formatted in the FAT file system.
• USB 2.0 HDDs should be connected to a separate power
source. Otherwise, the USB 2.0 HDDs will not work.
• If multiple USB external storage devices are connected
together, only the MP3 files in the first HDD will be played.
• Files with DRM are not supported. Digital Right
Management (DRM) restricts unauthorized access to a
DRM file so that the copyright of the file is protected from
piracy.
• Even if a file has an .mp3 extension, the file cannot be
played if it is formatted in MPEG layer 1 or 2.
• Do not use an unrecognized USB hub.
• Only the first 15 characters of a MP3/WMA file are
displayed.
• Only removable HDDs with less than 160GB are supported.
Depending on the device, a 160GB- or more removable
HDD may not be supported.
• It can take several minutes for the product to recognize the
files on some USB devices.
• Some USB devices (USB HDDs, in particular) may cause a
delay when moving from track to track.
• With USB storage devices supporting USB VER1.1 only,
the product may access files slowly or may not recognize
file properties.
• The maximum electrical current supported by external USB
devices via each USB port is 0.5A (based on DC 5V).
• A certain USB, digital camera device, USB card reader,
iPod, iPhone or Smart Phone may not be supported.
12
Bluetooth
You can use a Bluetooth device to enjoy music with
high quality stereo sound, all without wires!
What is Bluetooth?
Bluetooth is a technology that enables Bluetooth
compliant devices to interconnect easily with each
other using a short wireless connection.
• A Bluetooth device may cause noise or malfunction,
depending on usage, when:
-- A part of your body is in contact with the receiving/
transmitting system of the Bluetooth device or the Hi-Fi
Component.
-- It is subject to electrical variation from obstructions
caused by a wall, corner, or office partitioning.
-- It is exposed to electrical interference from same
frequency-band devices including medical equipment,
microwave ovens, and wireless LANs.
• Pair the Hi-Fi Component with the Bluetooth device while
they are close together.
• The greater the distance between the Hi-Fi Component and
the Bluetooth device, the worse the quality. If the distance
exceeds the Bluetooth operational range, the connection is
lost.
• In poor reception-sensitivity areas, the Bluetooth connection
may not work properly.
• The Bluetooth connection only works when it is close to
the set. The connection will be automatically cut off if the
Bluetooth device is out of range. Even within range, the
sound quality may be degraded by obstacles such as walls
or doors.
• This wireless device may cause electric interference during
its operation.
To connect the Hi-Fi Component to a
Bluetooth device
Before you begin, confirm that your Bluetooth
device supports the Bluetooth-compliant stereo
headset function.
1. Press the CD/ Bluetooth button of the Hi-Fi Component
to display the BLUETOOTH message.
• You will see WAIT for a while and then READY on the
front display of the Hi-Fi Component.
elect the Bluetooth menu on the Bluetooth device you
2. S
want to connect. (Refer to the Bluetooth device's user
manual.)
3. Select the Stereo headset menu on the Bluetooth device.
• You will see a list of scanned devices.
4. Select "[Samsung] HI-FI XXXXXX" from the list.
• When the product is connected to the Bluetooth
device, it will display CONNECTED ➞ BLUETOOTH
on the front display.
English
MX-FS9000-XU-ENG_130927.indd 12
2013-09-27 �� 1:40:03
Basic functions
• If the Bluetooth device has failed pair with the product,
delete the previous “[Samsung] HI-FI XXXXXX” found by
the Bluetooth device and have it search for the product
again.
5. Play music on the connected device.
• You can listen to the music playing on the connected
Bluetooth device over the Hi-Fi Component system.
• In Bluetooth mode, some model's Play/Repeat/Stop/
Next/Back functions are not available.
product only supports Middle Quality SBC data (up
➣➣[email protected]),
and does not support High Quality
SBC data ([email protected]).
• The AVRCP feature is not supported.
• Connect only to a Bluetooth device that supports the
A2DP (AV) function.
• You cannot connect to a Bluetooth device that
supports only the HF (Hands Free) function.
• Only one Bluetooth device can be paired at a time.
• Once you have turned off Hi-Fi Component and the
pairing is disconnected, the pairing will not be restored
automatically. To reconnect, you must pair the device
again.
• The Hi-Fi Component system may not search or
connect properly in the following cases:
-- If there is a strong electrical field around Hi-Fi
Component.
-- If several Bluetooth devices are simultaneously paired
with Hi-Fi Component.
-- If the Bluetooth device is turned off, not in place, or
malfunctions.
-- Note that such devices as microwave ovens, wireless
LAN adaptors, fluorescent lights, and gas stoves use
the same frequency range as the Bluetooth device,
which can cause electric interference.
To disconnect the Bluetooth device from
the Hi-Fi Component
You can disconnect the Bluetooth device from HiFi Component. For instructions, see the Bluetooth
device's user manual.
• The Hi-Fi Component will be disconnected.
• When the Hi-Fi Component is disconnected from the
Bluetooth device, the Hi-Fi Component will display
DISCONNECTED ➞ READY on the its front display.
To disconnect the Hi-Fi Component
from the Bluetooth device
Press the CD/Bluetooth button on the front panel
of the Hi-Fi Component to switch from Bluetooth
mode to another mode or turn off the Hi-Fi Component.
• The connected Bluetooth device will wait a certain amount
of time for a response from the Hi-Fi Component before
terminating the connection.(Disconnection time may differ,
depending on the Bluetooth device)
• The currently connected device will be disconnected.
connection mode, the Bluetooth connection
➣➣Iwilln Bluetooth
be lost if the distance between the Hi-Fi Component
and the Bluetooth device exceeds 16.25 feet (5 meters).
• If the Bluetooth device comes back into the effective
range after disconnecting, you can restart the Hi-Fi
Component to restore the pairing with the Bluetooth
device.
• The Hi-Fi Component automatically turns off after 25
minutes in the Ready mode.
Using My Karaoke
You can use the MY Karaoke function to sing
along with your favourite CDs and USB tracks.
1. Connect the microphone to the MIC jack on the front
of the product.
`` If your microphone plug is larger than the 3.5 (ø) MIC
jack, you need a Connector-Adaptor (optional) to
complete the connection.
-- First, connect the Connector-Adaptor to the MIC jack
on the front of the product,
-- Second, connect the microphone (with the larger
jack) to the Connector-Adaptor.
2. Press the MIC VOL-, + button on the remote
control to adjust the volume of the microphone.
3. Press the MY KARAOKE button on the remote
control to suppress the vocal if you need. Each time
the button is pressed, the selection is changed as
follows:
MY KARAOKE ON ➞ MY KARAOKE OFF
`` If you hear strange noises (squealing or howling)
while using the Karaoke feature, move the
microphone away from the speakers. Turning down
the microphone's volume or the speaker volume is
also effective. Do not set the MICROPHONE towards
the SPEAKER.
`` The microphone does not operate in the AUX and
TUNER mode.
`` If you connect a microphone, GIGA SOUND
automatically turns off. To turn Giga Sound back on
you must remove the microphone, and then press
the Giga Sound button.
English
MX-FS9000-XU-ENG_130927.indd 13
13
2013-09-27 �� 1:40:03
Basic Functions
`` When My Karaoke is on, EQ/GIGA SOUND and
FOOTBALL MODE does not work.
`` When you stop playing the CD or USB, My Karaoke
turns off automatically.
`` My Karaoke is only available when a microphone is
connected to the HI-Fi Component.
10 Skip Function
Press the +10 or -10 button while the unit is in
playback mode. The unit will skip as many as 10
tracks forward or 10 tracks back from the current
track.
Auto Change Function
You can set the product to play a disc, and then
play files on USB devices connected to USB 1
and USB 2 continuously.
1. Press the AUTO CHANGE button on the remote.
Each time you press this button, the mode
switches as follows:
AUTO CHANGE OFF ; AUTO CHANGE ON
• When AUTO CHANGE is "ON",
-- The Hi-Fi Component will play a disc in the disc slot,
then play files on a USB device connected to USB1,
and then play files on a USB device connected to
USB2. The files will be played continuously.
-- If you press the POWER button, function change
button, or the EJECT button, the AUTO CHANGE
function automatically turns "OFF".
-- Recording is disabled.
-- The REPEAT and SLEEP functions are automatically
set to OFF and are unavailable.
-- The CD REC SPEED, USB REC, PROGRAM and
DELETE functions unavailable.
• If you disconnect a playing USB device, the AUTO
CHANGE function automatically turns "OFF".
• If there's no device in USB1, the function automatically
switches to USB2.
Listening to the Radio
To Store the Stations You Want
You can store up to:
15 FM stations.
1. Select FM by pressing the TUNER/AUX button.
2. To search for a station, press the TUNNING MODE
button on the remote control or the STOP button on
the product one or more times until MANUAL is
displayed.
• Preset : Once or more times until PRESET is
displayed. You can search the stored
frequencies in the preset mode.
• Manual : Once or more times until MANUAL is
displayed. You can search the frequencies
one by one in the Manual mode.
3. Select a station by:
• Pressing the TUNING/ALBUM , or . button on
the remote control to find a station.
4. Press the MO/ST button to switch between stereo and
mono.
• In a poor reception area, select MONO for a clear, interference-free broadcast.
• This applies only when listening to an FM station.
5. If you do not want to store the radio station found, go
back to Step 3 and search for another station.
Otherwise:
a. Press the ENTER button.
b. Or, press the TUNING/ALBUM button on the
remote control to select a program number.
c. Press the ENTER button to save the preset.
6. To store other radio frequencies, repeat Steps 3, 4 and 5.
➣➣In Tuner mode
• In the Manual mode, you can use the [ or ]
button on the product to search for a radio station
manually.
• In the Preset mode, you can use the [ or ]
button or the EASY SEARCHING JOG control on
the product to search for a stored radio station.
Selecting a Stored Station
To listen to a stored station, follow these steps:
1. Select FM by pressing the TUNER/AUX button on
the product or remote control.
2. Press the TUNING MODE button on the remote
control until “PRESET” is displayed.
3. Press [,] button on the main unit or the TUNING/
ALBUM , , . on the remote control to select a
preset number.
or
Turn the EASY SEARCHING JOG control left or right on
the main unit to select a stored station.
14
English
MX-FS9000-XU-ENG_130927.indd 14
2013-09-27 �� 1:40:03
Advanced Functions
Timer Function
Setting the Clock
For each step, you have a few seconds to set the
required options. If you exceed this time, you must
start again.
1. Press the TIMER SET button on the remote
control twice. "CLOCK SET" is displayed.
) button on the remote
2. Press the ENTER (
control. The hour flashes.
• Increase the hours: TUNING/ALBUM ,
• Decrease the hours: TUNING/ALBUM .
3. When the correct hour is displayed, press the
) button, and then the minutes flash.
ENTER (
• Increase the minutes: TUNING/ALBUM ,
• Decrease the minutes: TUNING/ALBUM .
4. When the correct minute is displayed, press the
) button, and then "TIMER PLAY
ENTER (
SET" appears in the display.
Setting the Timer
The timer enables you to switch the product on or
off at specific times automatically.
• Before setting the timer, check that the current time
is correct.
• For each step, you have a few seconds to set the
required options. If you exceed this time, you must
start again.
• If you no longer want the product to be switched
on or off automatically, you must cancel the timer
by pressing the TIMER ON/OFF button.
Example: You want to wake up to music every morning.
1. Press the Timer SET button until TIMER PLAY SET is
displayed.
2. Press the ENTER (
) button.
Result: O
N TIME is displayed for a few seconds. You
can set the timer switch-on time.
3. Set the timer switch-on time.
a P
ress the TUNING/ALBUM , or . button to set the hours.
) button.
ress the ENTER (
b P
Result: The minutes flash.
c Press
the TUNING/ALBUM , or . button to set the minutes.
) button.
d P
ress the ENTER (
Result: O
FF TIME is displayed for a few seconds.
You can now set the timer switch-off time.
4. Set the timer switch-off time.
a P
ress the TUNING/ALBUM , or . button to set the hours.
) button.
b P
ress the ENTER (
Result: The minutes flash.
the TUNING/ALBUM , or . button to set c Press
the minutes.
) button.
d Press the ENTER (
Result: V
OLUME XX is displayed, where XX corresponds to the volume already set.
ress the TUNING/ALBUM , or . button to adjust the
5. P
volume level and press the ENTER (
) button.
Result: The source to be selected is displayed.
6. Press the TUNING/ALBUM , or . button to select the
source the Hi-Fi Component will play when it switches
on.
If you select...
You must also...
FM (radio) .................... a Press the ENTER (
)
button.
b Select
a preset station by
pressing the TUNING/
ALBUM , or . button.
CD (compact disc) ......Load a compact disc.
USB.............................Connect the USB device.
7. Press the ENTER ( ) button.
Result: TIMER REC SET (Do you want to record?) is
displayed.
8. Press the ENTER ( ) button.
Result: REC SET YES/NO is displayed. You can press
the TUNING/ALBUM , or . button to select
REC YES or REC NO, and then press
ENTER button.
1)If you select REC NO, it will cancel tuner timer
recording even if you have already set the tuner timer
recording.
2)If you select REC YES, you can set the tuner timer
recording on and off times.
) button.
a.Press the ENTER (
Result: O
N TIME is displayed for a few seconds.
You can set the tuner timer recording switchon time.
) button.
b.Press the ENTER (
Result: O
FF TIME is displayed for a few seconds.
You can set the tuner timer recording switchoff time.
English
MX-FS9000-XU-ENG_130927.indd 15
15
2013-09-27 �� 1:40:04
Advanced Functions
• The maximum length of time for tuner timer recording is
5 hours.
• If the timer switch on and off times are identical, the
word ERROR is displayed.
• You can use the [, ] buttons on the product
instead of the TUNING/ALBUM , or . button to
make adjustments in Steps 3 through 8.
• If the switch-on or -off time is the same as the timer
recording time, only the switch-on or -off time is
effective, and the timer recording is not applied.
• When you use the auto timer, you may need an
additional step to use a CD or USB device with it,
depending on the disc (or device). Consequently, it is
easier to use the tuner instead.
• If you select CD or USB mode when there is no disc or
no USB in the product, it will automatically change to
TUNER.
USB 1
• Connect the USB device with the files you want to
record to USB 1 jack.
• Press the USB button to select USB 1.
• Play a song from USB 1.
External Source
• Connect an External device/MP3 player to the
product.
• Press the TUNER/AUX button to select <AUX IN 1 or
AUX IN 2>.
• Play a song from the external device.
3. P
ress the USB REC button on the remote control to
start recording.
CD
• Track recording message is displayed and CD
recording starts.
Cancelling the Timer
• If you want to record all the tracks on the disc,
press and hold the USB REC button. Then, Full CD
recording message will be displayed.
After having set the timer, it will start automatically
as shown by the TIMER ON message on the display. If you no longer want to use the timer, you
must cancel it.
RADIO
• Tuner recording message is displayed and recording
starts.
To cancel the timer, Press the TIMER ON/OFF button
once.
To restart the timer, Press the TIMER ON/OFF button
once again.
CD-ROM/ USB
• “FILE COPY” is displayed and recording starts.
• You can also copy a folder including MP3/WMA files
to a device on USB 2. if you press and hold the USB
REC button while the system plays an MP3 or WMA
file in a folder, your system will display "FOLDER
COPY".
• When the recording is done, “STOP” will be displayed.
• If there is a file with the same name on the USB 2
device, "EXIST FILE" is displayed, and the function is
cancelled.
• If a microphone is connected to the product and you
press the USB REC button, you activate the MP3
Recording function, not the Copy function.
• When you press the USB REC button for a second,
file copy starts. When you press the USB REC button
for a few seconds, folder copy starts.
• When you select the TIMER OFF mode, the TIMER
RECORDING and TIME function are not available.
The Recording Function
Basic Recording
You can record from a CD, a USB device, a radio
broadcast, or an external source to a USB storage
device.
1. C
onnect the external USB storage device to a USB
(
) jack on your product.
2. Play a disc or USB, turn on the radio and select a
station, or connect the external source to your
product as described below.
CD
• Press the CD button on the product to select the CD
function.
• Insert a CD gently into the disc slot.
• Use the CD selection ( [ or ] ) buttons to select the
desired song.
TUNER
• Select FM by pressing the TUNER/AUX button.
• Select the radio frequency you want to record.
16
External Source
• AUX recording message is displayed and recording
starts.
CD/USB1(MP3) & MIC
• MP3 recording message is displayed and recording
starts.
4. T
o stop recording, press the STOP (@) button.
The recording is automatically saved as an MP3
file.
5.
After the recording is finished, a directory named
“RECORDING”(CD-DA), “CD COPY”(CD-ROM/
USB(WMA/MP3)), “TUNER RECORDING”, “AUX
RECORDING” or “MP3 RECORDING” is created in
your device.
English
MX-FS9000-XU-ENG_130927.indd 16
2013-09-27 �� 1:40:04
Advanced functions
• The WMA/MP2 file just can be copied not recorded.
• Do not disconnect the USB device or the AC Cord during
recording. You can cause file damage.
• If you disconnected the USB device during recording,
the product will turn off and you will not be able to delete
the file that has been recorded. If his occurs, connect the
USB device to a PC, back up the USB data to the PC,
and then reformat the USB device.
• If the USB device does not have enough memory, “NOT
ENOUGH MEMORY” will appear on the display.
• The Recording function supports the FAT file systems
only. The NTFS file system is not supported.
• When you use the CD high speed search function, the
CD recording function is unavailable.
• With some USB devices, recording time may be longer.
• In the Program mode, you can't use the CD recording
function.
• When the Recording function is active, the EQ and
GIGA SOUND functions automatically turn off and are
unavailable.
• During a CD recording, the REPEAT function automatically
turns off and is unavailable.
• If you use the MIC function during a CD recording, the
voice from the microphone will be recorded.
• You can not record audio from the radio when searching
for a station or if there are no frequencies available when
the product is set to Tuner mode.
• Note that setting the input level too loud when recording
music from an external device through the AUX or USB
channel may introduce noise into the recording. If this
occurs, lower the external device’s volume level.
Recording Speed
Each time you press the CD REC SPEED button
on the remote control, the recording speed will
change as follows:
RECORD SPEED x 1; RECORD SPEED X 4
• When you record from the tuner or an external source, you
cannot change the recording speed.
• If you select RECORD SPEED X 4, sound is not produced
during the recording.
• If you connect the microphone, you have one recording speed
mode available: RECORD SPEED X 1.
• During recording, if you disconnect the microphone, the
recording will stop. If you reconnect the microphone, the
recording will not restart.
Special Sound Effect
Selecting EQ Mode
Your Hi-Fi Component system provides predefined
equalizer settings that are optimized for particular
music genre. You can also adjust the bass, middle
and treble levels manually.
1. Press the EQ button.
Each time you press this button, the sound mode will .
switch as follows:
OFF;FLAT;RANCHERA;SAMBA;CUMBIA;
HABANERA;BOOMBA;REGGAE;MERENGUE;
SALSA;PARTY;POP;HIP HOP;ROCK;JAZZ;
CLASSIC;ELECTRONIC;MP3 ENHANCER;
VIRTUAL SOUND;USER EQ
2. To set the BASS, MID (Middle) and TREB (Treble)
levels manually, select USER EQ, and then press
the ENTER button.
Result: The BASS level (left numeric) flashes..
P
ress the TUNING/ALBUM , or . button to
s elect a level from -06 to 06.
Then, press the ENTER button.
Result: The MIDDLE level (middle numeric) flashes.
P
ress the TUNING/ALBUM , or . button to
select a level from -06 to 06.
Then, press the ENTER button.
Result: T
he TREBLE level (right numeric) flashes.
Press the TUNING/ALBUM , or . button to
select a level from -06 to 06.
Then, press the ENTER button.
Result: Setting is complete.
• When the Hi-Fi Component is recording, the EQ function is
turned off automatically and is unavailable.
• If no buttons are pressed within 8 seconds, your settings will
automatically be cancelled and the previous settings will be
saved.
• The EQ mode may be different depending on your region.
Using the FOOTBALL Mode
The football mode brings greater realism to sports
broadcasts.
1. Press the FOOTBALL MODE button on the product.
Each time you press the button, the sound mode
switches as follows:
FOOTBALL OFF ; FOOTBALL MODE 1 ;
FOOTBALL MODE 2
• The FOOTBALL mode may be different depending on your
region.
GIGA SOUND Function
The GIGA SOUND function amplifies the bass
sound and provides twice the bass for powerful,
realistic sound.
1. P
ress the GIGA SOUND BEAT button on the main
unit or the GIGA button on the remote control.
Each time you press the button, the sound mode
switches as follows:
GIGA SOUND BEAT ; GIGA SOUND OFF
2. T
o cancel this function, press the GIGA SOUND
BEAT button until “OFF” is displayed.
• The GIGA SOUND mode may be different depending
on your region.
English
MX-FS9000-XU-ENG_130927.indd 17
17
2013-09-27 �� 1:40:05
Advanced Functions
BEAT WAVING Function
Booting Sound Function
The Beat Waving function lets you change the
Speaker LED display mode.
If you set the booting sound, you can feel the
magnificent audio output of the product while it
boots up.
1. Each time you press the BEAT WAVING button on
the product, the Speaker LED display mode changes
as follows:
PARTY 1 ; PARTY 2 ; FUN 1 ; FUN 2 ; PURE ;
FRESH ; LOVE ; JOY ; SUNSET ; SUNRISE ;
NATURE 1 ; NATURE 2 ; WAVE 1 ; WAVE 2 ;
AURORA ; OFF
• If you select BEAT WAVING OFF, all the speaker LED
displays are turned off.
1. Press the product's GIGA SOUND BEAT button or
the remote control's GIGA button for a long time.
• The BOOTING SOUND menu appears on the display
panel.
2. Press the product's GIGA SOUND BEAT button or
the remote control's GIGA button for a long time to
turn ON or OFF the BOOTING SOUND.
DJ BEAT Function
The DJ Beat function lets you turn on the
FLANGER, PANNING, CHORUS, and WAHWAH
sound effect functions. The level of each effect is
adjustable.
☛☛The set scope is [-15 ~ +15] and the initial set up
values are all 0.
FLANGER : C
reates a vibration similar to the sound of a jet
engine revving up and down.
PANNING : Increases the left and right speaker's output in
turn and makes it seem as if the sound is moving
from side to side.
WAHWAH : Creates a 'Wah~ Wah~' effect.
CHORUS : Creates a vibration that sounds like a singing
chorus.
1. To set the desired effect, press the FLANGER,
PANNING, CHORUS, or WAHWAH button on the
product.
• The blue LED turns on around the button you pushed
and around the DJ BEAT button.
• You can control the intensity of the effect with the
Volume Jog. To control the volume, press the product's
DJ BEAT button.
• To cancel an effect, press the effect's button again.
• To change to a different effect, press another effect
button.
• You can apply the PANNING effect to the FLANGER,
CHORUS, or WAHWAH effects.
• To apply the PANNING effect to another effect, press
the PANNING button when the other effect is active or
press another effect button when the PANNING effect
is active.
• Use the Volume JOG to control the intensity of the
effect that was activated last. For example, if you
activated the WahWah effect and then the Panning
effect, the Volume Jog will control the Panning effect.
• To control the intensity of the effect you applied first,
press the button of effect that you applied last to turn
it off. Then, you can use the Volume Jog to control the
intensity of the first effect.
18
English
MX-FS9000-XU-ENG_130927.indd 18
2013-09-27 �� 1:40:05
Troubleshooting
Troubleshooting
Refer to the chart below when this product does not function properly. If the problem you are
experiencing is not listed below or if the instruction below does not help, turn off the product,
disconnect the power cord, and contact the nearest authorized dealer or Samsung Electronics Service
Centre.
Symptom
Check/Remedy
I cannot eject the disc.
• Is the power cord plugged securely into the outlet?
• Turn off the power and then turn it back on.
Playback does not start
immediately when the
Play/Pause button is pressed.
• Are you using a deformed disc or a disc with scratches on the surface?
• Wipe the disc clean.
Sound is not produced.
• No sound is heard during fast playback, slow playback, and step
motion playback.
• Are the speakers connected properly? Is the speaker setup correctly
customized?
• Is the disc severely damaged?
The remote control does not
work.
• Is the remote control being operated within its operational angle and
distance range?
• Are the batteries drained?
• The product is not working.
• Run the reset function. With the “NO DISC” message on the display of
(Example: The power goes out or the product and no disc in the disc slot, press and hold the STOP (@)
the front panel key doesn't work
button on the product for more than 5 seconds.
or you hear a strange noise.)
Using the RESET function will erase all stored settings.
• The product is not working
Do not use this unless necessary.
normally.
Can't receive radio broadcast.
• Is the antenna connected properly?
• If the antenna's input signal is weak, install an external FM antenna in an
area with good reception.
English
MX-FS9000-XU-ENG_130927.indd 19
19
2013-09-27 �� 1:40:05
Specifications
Specifications
Main unit
Speaker
Main unit
Dimensions
Speaker
Operating Temperature Range
Operating Humidity Range
Signal/Noise ratio
Usable sensitivity
Total harmonic distortion
Weight
General
FM Tuner
CD Disc
Amplifier
CD : 12 cm (COMPACT DISC)
8 Kg
70 Kg
588 (W) X 238 (H) X 388 (D)
588 (W) X 882 (H) X 577 (D)
+5°C~+35°C
10 % to 75 %
55 dB
10 dB
1%
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 74 min.
Front speaker output
640W/CH (4Ω)
Subwoofer output
640W/CH (4Ω)
Frequency range
22Hz~20KHz
S/N Ratio
65 dB
Channel separation
60 dB
Input sensitivity
(AUX)800mV
*: Nominal specification
- Samsung Electronics Co., Ltd reserves the right to change the specifications without notice.
- Weight and dimensions are approximate.
- Design and specifications are subject to change without prior notice.
- For information on the power supply and power consumption, refer to the label attached to the product.
20
English
MX-FS9000-XU-ENG_130927.indd 20
2013-09-27 �� 1:40:05
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG
customer care Centre.
Country
Contact Centre 
AUSTRIA
0810 - SAMSUNG (7267864,
€ 0.07/min)
BELGIUM
02-201-24-18
BOSNIA
BULGARIA
CROATIA
CZECH
DENMARK
FINLAND
FRANCE
051 331 999
07001 33 11 , share cost tariff
062 SAMSUNG (062 726 786)
800 - SAMSUNG (800-726786)
70 70 19 70
030-6227 515
01 48 63 00 00
0180 6 SAMSUNG bzw.
0180 6 7267864*
(*0,20 €/Anruf aus dem dt.
Festnetz, aus dem Mobilfunk
max. 0,60 €/Anruf)
8009 4000 only from landline
80111-SAMSUNG (80111 726
7864) only from land line
(+30) 210 6897691 from mobile
and land line
GERMANY
CYPRUS
GREECE
HUNGARY
06-80-SAMSUNG(726-7864)
ITALIA
LUXEMBURG
MONTENEGRO
800-SAMSUNG(726-7864)
261 03 710
020 405 888
Web Site
Country
www.samsung.com
NETHERLANDS
www.samsung.com/be
(Dutch)
www.samsung.com/be_
fr (French)
www.samsung.com
www.samsung.com/bg
www.samsung.com/hr
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com/fr
NORWAY
POLAND
PORTUGAL
ROMANIA
SERBIA
www.samsung.com
SLOVAKIA
SPAIN
SWEDEN
Contact Centre 
0900-SAMSUNG (09007267864) (€ 0,10/Min)
815 56480
0 801-172-678* lub +48 22
607-93-33 **
* (całkowity koszt połączenia
jak za 1 impuls według taryfy
operatora)
** (koszt połączenia według
taryfy operatora)
808 20-SAMSUNG(808 20
7267)
08008 SAMSUNG (08008 726
7864) TOLL FREE No.
011 321 6899
0800 - SAMSUNG(0800-726
786)
902172678
0771 726 7864 (SAMSUNG)
www.samsung.com/gr
SWITZERLAND
0848 - SAMSUNG(7267864,
CHF 0.08/min)
http://www.samsung.
com/hu
www.samsung.com
www.samsung.com
www.samsung.com
U.K
EIRE
LITHUANIA
LATVIA
ESTONIA
0330 SAMSUNG (7267864)
0818 717100
8-800-77777
8000-7267
800-7267
[Correct disposal of batteries in this product]
(Applicable in countries with separate collection systems)
This marking on the battery, manual or packaging indicates that the batteries in
this product should not be disposed of with other household waste at the end of
their working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that
the battery contains mercury, cadmium or lead above the reference levels in EC
Directive 2006/66. If batteries are not properly disposed of, these substances can
cause harm to human health or the environment.
To protect natural resources and to promote material reuse, please separate
batteries from other types of waste and recycle them through your local, free
battery return system.
Web Site
www.samsung.com
www.samsung.com
www.samsung.com/pl
www.samsung.com
www.samsung.com/ro
www.samsung.com/rs
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com/ch
(German)
www.samsung.com/ch_
fr (French)
www.samsung.com
www.samsung.com
www.samsung.com/lt
www.samsung.com/lv
www.samsung.com/ee
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and
its electronic accessories (e.g. charger, headset, USB cable) should not be disposed
of with other household waste at the end of their working life. To prevent possible
harm to the environment or human health from uncontrolled waste disposal, please
separate these items from other types of waste and recycle them responsibly to
promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product,
or their local government office, for details of where and how they can take these
items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions
of the purchase contract. This product and its electronic accessories should not be
mixed with other commercial wastes for disposal.
AH68-02612M-01
MX-FS9000-XU-ENG_130927.indd 21
2013-09-27 �� 1:40:07
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement