Samsung | DVD-HR750 | Samsung DVD-HR750 User Manual

Instruction Manual
DVD-HR749
DVD-HR750
< DVD-HR749 >
< DVD-HR750 >
www.samsung.com/uk
English
Ελληνικά
01392A_HR750_XEU-ENG-0423.indd 1
AK68-01392A
2007-04-24
9:30:59
Getting Started
Getting Started
IMPORTANT NOTE
Warning
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE THE COVER (OR BACK).
NO USER-SERVICEABLE PARTS ARE INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The mains lead on this equipment is supplied with a
moulded plug incorporating a fuse. The value of the
fuse is indicated on the pin face of the plug. If it
requires replacing, a fuse approved to BS1362 of the
same rating must be used.
Never use the plug with the fuse cover omitted if the
cover is detachable. If a replacement fuse cover is
required, it must be of the same colour as the pin face
of the plug. Replacement covers are available from
your dealer.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This symbol indicates “dangerous voltage”
inside the product that presents a risk of
electric shock or personal injury.
This symbol indicates important
instructions accompanying the product.
If the fitted plug is not suitable for the power points in
your house or the cable is not long enough to reach a
power point, you should obtain a suitable safety
approved extension lead or consult your dealer for
assistance.
Do not install this equipment in a confined space such
as a bookcase or similar unit.
However, if there is no alternative to cutting off the
plug, remove the fuse and then safely dispose of the
plug. Do not connect the plug to a mains jack, as there
is a risk of shock hazard from the bared flexible cord.
WARNING : To prevent damage which may result in
fire or electric shock hazard, do not
expose this appliance to rain or moisture.
To disconnect the apparatus from the mains, the plug
must be pulled out from the mains socket, therefore
the mains plug shall be readily operable.
CAUTION : HDD & DVD RECORDER USES AN
INVISIBLE LASER BEAM WHICH CAN
CAUSE HAZARDOUS RADIATION
EXPOSURE IF DIRECTED. BE SURE TO
OPERATE HDD & DVD RECORDER
CORRECTLY AS INSTRUCTED.
CAUTION
THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR
YOURSELF. REFER SERVICING TO QUALIFIED
PERSONNEL.
The product unit accompanying this user manual is
licenced under certain intellectual property rights of
certain third parties. This licence is limited to private
non-commercial use by end-user consumers for
licenced contents.
No rights are granted for commercial use.
The licence does not cover any product unit other than
this product unit and the licence does not extend to
any unlicenced product unit or process conforming to
ISO/IEC 11172-3 or ISO/IEC 13818-3 used or sold in
combination with this product unit. The licence only
covers the use of this product unit to encode and/or
decode audio files conforming to the ISO/IEC 11172-3
or ISO/IEC 13818-3. No rights are granted under this
licence for product features or functions that do not
conform to the ISO/IEC 11172-3 or ISO/IEC 13818-3.
This product satisfies CE regulations when shielded
cables and connectors are used to connect the unit to
other equipment. To prevent electromagnetic
interference with electric appliances, such as radios
and televisions, use shielded cables and connectors
for connections.
English - 2
01392A_HR750_XEU-ENG-0423.indd 2
2007-04-24
9:31:30
Handling Cautions
Important Safety Instructions
Read these operating instructions carefully before
using the unit. Follow all the safety instructions listed
below. Keep these operating instructions handy for
future reference.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings, Install in
accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized
or grounding- type plug. A polarized plug has two
blades with one wider than the other. A groundingtype plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, the point where they exit from the
apparatus.
11) Only use attachments/accessories specified by the
manufacturer.
12) Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
• Before connecting other components to this HDD &
DVD RECORDER, be sure to turn them all off.
• Do not move the HDD & DVD RECORDER while a
disc is being played, or the disc may be scratched or
broken, the HDD & DVD RECORDER internal parts
may be damaged.
• Do not put a flower vase filled with water or any small
metal objects on the HDD & DVD RECORDER.
• Be careful not to put your hand into the disc tray.
• Do not place anything other than the disc in the disc
tray.
• Exterior interference such as lightning and static
electricity can affect normal operation of this HDD &
DVD RECORDER. If this occurs, turn the HDD &
DVD RECORDER off and on again with the
STANDBY/ON button, or disconnect and then
reconnect the AC power cord to the AC power outlet.
The HDD & DVD RECORDER will operate normally.
• Be sure to remove the disc and turn off the HDD &
DVD RECORDER after use.
• Disconnect the AC power cord from the AC outlet
when you don’t intend to use the HDD & DVD
RECORDER for long periods of time.
• Clean the disc by wiping in a straight line from the
inside to the outside of the disc.
• Apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such as
vases, shall be placed on the apparatus.
• The Mains plug is used as a disconnect device and
shall stay readily operable at any time.
Getting Started
Precaution
Maintenance of Cabinet
For safety reasons, be sure to disconnect the AC
power cord from the AC outlet.
• Do not use benzene, thinner, or other solvents for
cleaning.
• Wipe the cabinet with a soft cloth.
13) Unplug this apparatus during lightning storms or
when unused for long periods of time.
HDD (Hard Disk Drive)
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
The hard disk has a high storage density, which
enables long recording durations and quick access to
written data. However, it can easily be damaged by
shock, vibration or dust and should be kept away from
magnets. To avoid losing important data, observe the
following precautions.
• Do not use the HDD & DVD RECORDER in a place
subject to extreme changes in temperature.
• Do not apply a strong shock to the HDD & DVD
RECORDER.
English - 3
01392A_HR750_XEU-ENG-0423.indd 3
2007-04-24
9:31:30
Getting Started
• Do not place the HDD & DVD RECORDER in a
location subject to mechanical vibrations or in an
unstable location.
Disc Storage
• Do not place the HDD & DVD RECORDER on top of
a heat source.
Be careful not to harm the disc because the data on
these discs is highly vulnerable to the environment.
• Do not keep under direct sunlight.
• Do not disconnect the AC power cord while the
power is on.
• Keep in a cool ventilated area.
• Do not attempt to change the hard disk. This may
result in a malfunction.
• Keep in a clean protection jacket.
• Store vertically.
Should the hard disk be damaged, you cannot recover
lost data. The hard disk is only a temporary storage
space.
Disc Handling
• Use discs with regular
shapes. If an irregular disc (a
disc with a special shape) is
used, this HDD & DVD
RECORDER may be damaged.
• If you move your HDD & DVD RECORDER suddenly
from a cold place to a warm place, condensation may
generate on the operating parts and lens and cause
abnormal disc playback. If this occurs, do not connect
the plug to the power outlet and wait for two hours.
Then insert the disc and try to play back again.
Disc Specifications
• DVD-HR749 / DVD-HR750
This unit allows you to record and playback high
quality digital video on DVD-RAM/-RW/-R discs or on
the HDD.
You can also edit digital images on DVD-RAM/-RW
discs or HDD.
Holding discs
• Avoid touching the surface of a
disc where recording is performed.
Disc Type
◆ DVD-Video
DVD-RAM, DVD-RW and DVD-R
• A digital versatile disc (DVD) can contain up to
135-minutes of images, 8 audio languages and 32
subtitle languages. It is equipped with MPEG-2
picture compression and Dolby digital surrounding,
allowing you to enjoy vivid and clear theatre quality
images in the comfort of your own home.
• Clean with an optional DVD-RAM/
PD disc cleaner (LF-K200DCA1
where available). Do not use
cleaners or cloths for CDs to clean
DVD-RAM/-RW/-R discs.
DVD-Video, Audio-CD
• Wipe off dirt or contamination on the disc with a soft
cloth.
• When switching from the first layer to the second
layer of a dual-layered DVD Video disc, there may
be momentary distortion in the image and sound.
This is not a malfunction of the unit.
• Once a DVD-RW/-R recorded in Video Mode is
finalised, it becomes DVD-Video.
Cautions on handling discs
◆ Audio CD
• Do not write on the printed side with a ball-point pen
or pencil.
• An audio disc on which 44.1 kHz PCM Audio is
recorded.
• Do not use record cleaning sprays or antistatic. Also,
do not use volatile chemicals, such as benzene or
thinner.
• Plays CD-DA format audio CD-R and CD-RW discs.
• The unit may not be able to play some CD-R or
CD-RW discs due to the condition of the recording.
• Do not apply labels or stickers to discs. (Do not use
discs fixed with exposed tape adhesive or leftover
peeled-off stickers.)
• Do not use scratch-proof protectors or covers.
• Do not use discs printed with label printers available
on the market.
• Do not load warped or cracked discs.
English - 4
01392A_HR750_XEU-ENG-0423.indd 4
2007-04-24
9:31:31
◆ DVD-RW Disc Playback and Recording
• Use a 700MB (80 minutes) CD-R/-RW disc. If
possible, do not use a 800MB (90 minutes) or above
disc, as the disc may not play back.
• Recording and playback can be performed on
DVD-RW discs in both the Video and VR Modes.
• If the CD-R/-RW disc was not recorded as a closed
session, you may experience a delay in the early
playback time, all recorded files may not play.
• Some CD-R/-RW discs may not be playable with this
unit, depending on the device which was used to
burn them. For contents recorded on CD-R/-RW
media from CDs for your personal use, playability
may vary depending on contents and discs.
◆ DVD-R Disc Playback and Recording
• Once a DVD-R recorded in Video Mode is finalised,
it becomes DVD-Video.
• You can record onto the available space on the disc
and perform editing functions such as giving titles to
discs and programmes and erasing programmes
before finalising.
• When programming is erased from a DVD-R, that
space does not become available. Once an area on
a DVD-R is recorded on, that area is no longer
available for recording, whether the recording is
erased or not.
• It takes about 30 seconds for the unit to complete
recording management information after recording
finishes.
• Once a DVD-RW recorded in both the Video and VR
Modes is finalised, you cannot perform additional
recording.
• Once a DVD-RW recorded in Video Mode is
finalised, it becomes DVD-Video.
Getting Started
◆ CD-R/-RW
• In both modes, playback can be performed before
and after finalisation, but additional recording,
deleting and editing can not be performed after
finalisation.
• If you want to record the disc in VR Mode and then
record in V Mode, be sure to execute Format. Be
careful when executing Format because all the
recorded data may be lost.
• A DVD-RW blank disc is initialized to VR Mode when
first initialized.
◆ DVD-RAM Disc Playback and Recording
• Ensure that the recording mode is set to VR mode.
Otherwise, this product will not be able to play the
recording.
• You cannot play a DVD-RAM in most DVD
components due to compatibility issues.
• Only DVD-RAM standard Version 2.0. discs can be
played in this unit.
• DVD-RAM recorded on this unit may not work with
other DVD components. To determine compatibility
with these DVD-RAM discs, refer to the user’s
manual for the player.
• This product optimizes the DVD-R for each
recording. Optimizing is carried out when you start
recording after inserting the disc or turning on the
unit. Recording onto the disc may become
impossible if optimizing is carried out too many
times.
• For cartridge type DVD-RAM discs, remove the
cartridge and use the disc only.
• Playback may be impossible in some cases due to
the condition of recording.
• This unit can play back DVD-R discs recorded and
finalised with a Samsung DVD video recorder. It may
not be able to play some DVD-R discs depending on
the disc and the condition of the recording.
English - 5
01392A_HR750_XEU-ENG-0423.indd 5
2007-04-24
9:31:31
❋ For more information on DVD recording compatibility,
Getting Started
Disc Copy
consult your DVD-RAM/-RW/-R manufacturer.
❋ Use of poor quality DVD-RAM/-RW/-R discs may
Contents Copy Specifications
Contents
HDD ➔ DVD
DVD ➔ HDD
Recorded Video
Title
Supported
Supported
Copy Protected
Title
Not supported
Not supported
Copy Once Title
Move
(Deletes the Title in the Not supported
HDD after copying)
MP3
Supported
Supported
JPEG(photo)
Supported
Supported
DivX
Supported
Supported
cause following unexpected problems including,
without limitation, recording failure, loss of
recorded or edited materials or damage to the
HDD & DVD RECORDER.
Disc Format
◆ Using MP3 disc
• CD-R/-RW, DVD-RAM/±RW/±R, HDD with MP3 files
recorded with UDF, ISO9660 or JOLIET format can
be playbacked.
Once “Copy Once programme” has been recorded on
the DVD disc, this title cannot be copied to HDD
anymore.
But “Copy Once programme” has been recorded on
the HDD, this title can be copied to DVD-RW
(VR mode) or DVD-RAM.
• Only MP3 files with the “.mp3” or “.MP3” extension
can be played.
• For MP3 files recorded with a VBR(Variable Bit
Rates), from 32 Kbps to 320 Kbps, the sound may
cut in out.
• Playable bit-rate range is from 56 Kbps to 320 Kbps.
• Each folder can have up to 500 items including files
and sub folders.
When you copy MP3/JPEG/DivX files from HDD to
DVD, only DVD-RW(V)/-R discs are available.
◆ Using JPEG disc
COPY PROTECTION
• CD-R/-RW, DVD-RAM/±RW/±R, HDD recorded with
UDF, ISO9660 or JOLIET format can be playbacked.
• Many DVD discs are encoded with copy
protection. Because of this, you should only
connect your HDD & DVD RECORDER directly
to your TV, not to a VCR. Connecting to a VCR
results in a distorted picture from copy-protected
DVD discs.
• Only JPEG files with the “.jpg” or “.JPG” extension
can be displayed.
• Each folder can have up to 500 items including files
and sub folders.
• This product incorporates copyright protection
technology that is protected by methods claims
of certain U.S. patents and other intellectual
property rights owned by Macrovision
Corporation and other rights owners. Use of this
copyright protection technology must be
authorised by Macrovision Corporation, is
intended for home and other limited viewing
uses only unless otherwise authorised by
Macrovision Corporation. Reverse engineering
or disassembly is prohibited.
• MOTION JPEG and progressive JPEG are not
supported.
◆ Using DivX disc
• Disc : CD-R/-RW, DVD-RAM/±RW/±R, HDD
• Video File with following extensions can be played. :
.avi, .divx, .AVI, .DIVX
• DivX Video (Codec) Format : DivX 3.11 DivX 4.x
DivX 5.x (without QPEL and GMC)
• DivX Audio (Codec) Format : MP3, MPEG1 Audio
Layer 2, LPCM, AC3
Protection
This HDD & DVD RECORDER can allow you to
protect the contents of your discs, as described below.
• Programme-protected: See page 74 “Locking
(Protecting) a Title”
• Supported subtitle file formats: .smi, .srt, .sub, .psb,
.txt, .ass
• Each folder can have up to 500 items including files
and sub folders.
• You cannot play back the disc that is larger than a
720 x 576 pixel resolution.
• Disc-protected: See page 91 “Disc Protection”
❋ DVD-RAM/±RW/±R discs that are incompatible
with the DVD-VIDEO format cannot be played with
this product.
English - 6
01392A_HR750_XEU-ENG-0423.indd 6
2007-04-24
9:31:32
Do not use the following discs!
Getting Started
• LD, CD-G, CD-I, CD-ROM and DVD-ROM discs
should not be used in this product.
[Note]
Disc types that can be played : CD/CD-R/-RW/MP3/
JPEG/DVD-Video/DVD-RAM/-RW/-R.
For a DVD-RW/-R disc, which has been recorded in
Video Mode on another component, it can play only
when finalised.
• Some commercial discs and DVD discs purchased
outside your region may not be playable with this
product. When these discs are played, either “No
disc.” or “Please check the regional code of the disc.”
will be displayed.
• If your DVD-RAM/±RW/±R discs is an illegal copy or
is not in DVD video format, it may also not be
playable.
◆ Disc compatibility
• High Speed Recording discs can be used in this unit.
• Not all brands of discs will be compatible with this
unit.
English - 7
01392A_HR750_XEU-ENG-0423.indd 7
2007-04-24
9:31:32
Getting Started
Contents
Getting Started
 Warning ....................................................................... 2
 Precaution ................................................................... 3
Important Safety Instructions ...................................... 3
Handling Cautions....................................................... 3
Maintenance of Cabinet .............................................. 3
HDD (Hard Disk Drive) ............................................... 3
Disc Handling .............................................................. 4
Disc Storage................................................................ 4
Disc Specifications ...................................................... 4
Disc Copy .................................................................... 6
 Connecting to AV 3 IN, DV input jack ..................... 22
Case 1 : Connecting a VCR, Set-Top
Box(STB), DVD player or Camcorder
to the AV 3 IN jacks ................................................. 22
Case 2 : Connecting a Camcorder
to the DV IN jack ...................................................... 23
System Setup
 On-Screen Menu Navigation .................................... 24
 Plug & Auto Setup .................................................... 24
 General Features ...................................................... 10
 Setting the Clock ....................................................... 25
 Before reading the user’s manual ............................ 11
 Channel Set ............................................................. 26
Auto Setup ................................................................ 26
Manual Setup ............................................................ 26
 How to use the HDD & DVD RECORDER .............. 11
 Unpacking ................................................................. 13
 Description ................................................................ 15
Front Panel................................................................ 15
Rear Panel ................................................................ 16
Front Panel Display .................................................. 16
Tour of the Remote Control ...................................... 17
 Setting up the Language Options............................. 27
 Setting up the System Options ................................. 27
Auto Power Off Setting ............................................. 28
Automatic Chapter Creator ....................................... 28
EP Mode Time Setting.............................................. 29
EZ Record ................................................................. 29
DivX(R) Registration ................................................. 29
 Setting up the Audio Options.................................... 30
Connecting & Setting Up
 Connecting the HDD & DVD RECORDER .............. 18
 Additional connections .............................................. 18
 Other type of connecting the Video output cable .... 19
Case 1 : Connecting to a Video (Composite)
output jack ................................................................. 19
Case 2 : Connecting to an S-Video output jack ...... 20
Case 3 : Component Video output jacks.................. 20
 Other type of connecting the Audio output cable .... 21
Case 1 : Connecting to your TV .............................. 21
Case 2 : Connecting to a stereo amplifier with
AV output jacks ........................................................ 21
Case 3: Connecting to an AV amplifier with a
digital output jack ..................................................... 22
 Setting up the Video Options.................................... 32
 Setting up the Parental Lock .................................... 35
If you forgot your password ...................................... 35
Setting the Rating Level ........................................... 35
Changing the Password ........................................... 35
Playback
 Region code (DVD-Video only) ................................ 36
 Logos of Discs that can be played ........................... 36
 Disc types that can be played .................................. 36
 Playing a Disc ........................................................... 37
 Using the Disc Menu & Title Menu........................... 38
 Using the playback related buttons .......................... 39
English - 8
01392A_HR750_XEU-ENG-0423.indd 8
2007-04-24
9:31:32
 Using the INFO button .............................................. 41
 Selecting the Soundtracks & Audio Channels ......... 42
 Changing the Camera Angle .................................... 42
 Repeat Play............................................................... 43
 Zooming-In ................................................................ 44
 Using Markers ........................................................... 45
 Basic Editing (Title List) ............................................ 73
Playing the Title ........................................................ 73
Renaming (Labeling) a Title ..................................... 73
Locking (Protecting) a Title ...................................... 74
Deleting a Title ........................................................ 75
Splitting a Section of a Title (Split) ......................... 76
Deleting a Section of a Title (Partial Delete) .......... 77
 Using the Bookmarks................................................ 46
 Using the Sort function (Title List) ............................ 78
 Playing an Audio CD/MP3 ........................................ 47
 Navigation Menu ....................................................... 78
 Viewing a Picture ...................................................... 52
 Select Contents......................................................... 79
 Playing a DivX........................................................... 54
 Advanced Editing (Playlist) ....................................... 80
Creating a Playlist .................................................... 80
Playing Entries in the Playlist .................................. 81
Renaming a Playlist Entry ........................................ 81
Editing a Scene for the Playlist................................. 82
Deleting a Playlist Entry from the Playlist................. 84
Using the Sort (Playlist) ............................................ 85
Recording
 Recordable Discs ...................................................... 56
 Recording Formats ................................................... 57
 Recording Mode........................................................ 58
 Unrecordable pictures............................................... 59
 Copying from HDD to DVD....................................... 85
 Copying from DVD to HDD....................................... 87
 Copying from a Camcorder ...................................... 62
 Copying MP3, JPEG or DivX.................................... 88
File Copy ................................................................... 88
Folder Copy............................................................... 88
 Making a One Touch Recording (OTR) ................... 63
 Changing the name of Music/Photo/DivX file........... 90
 Simultaneous Recording and Playback ................... 64
 Disc Manager ............................................................ 91
Editing the Disc Name .............................................. 91
Disc Protection .......................................................... 91
Delete All Title Lists ................................................. 92
Delete All Title Lists/DivX Lists /Music Lists/
Photo Lists ................................................................ 92
Formatting a Disc ...................................................... 93
Finalising a Disc ....................................................... 94
Unfinalising a Disc (V/VR mode) ............................. 95
 Recording immediately ............................................. 60
 Time Shift function as a live signal ........................... 65
 Making a Timer Recording ...................................... 66
Editing the Scheduled List ........................................ 68
Adding a Scheduled List ........................................... 68
Deleting a Scheduled List ......................................... 69
 Using the Video Plus+ Feature ................................ 70
 Video Plus+ Extended .............................................. 71
Getting Started
 Selecting the Subtitle Language............................... 41
Editing
 Go To Recorded List................................................. 71
Reference
 Troubleshooting ........................................................ 96
 Specifications ............................................................ 98
English - 9
01392A_HR750_XEU-ENG-0423.indd 9
2007-04-24
9:31:32
Getting Started
Automated Quality Adjustment for Timer
Recording
General Features
• DVD-HR749 / DVD-HR750
This unit allows you to record and playback high quality
digital video on DVD-RAM/-RW/-R discs or on the HDD.
You can also edit digital images on DVD-RAM/-RW
discs or HDD.
HDD Recording
• DVD-HR749 / DVD-HR750
You can record up to Approx. 199 hours of video (in
EP mode) on the internal 160GB (gigabyte) hard disk
(HDD).
With both recordable DVD and a high-capacity HDD in the
same recorder, you have the flexibility to keep recordings
on the HDD for quick access anytime, or record to DVD
for archiving or playing on other DVD players.
If FR mode is selected, the video quality is adjusted
automatically so that all video for the scheduled time
can be recorded onto the free disc space.
(See page 66)
Creating a DVD video title using DVD-RW/-R
disc
With the HDD & DVD RECORDER, you can create your
own DVD Video titles on 4.7 GB DVD-RW/-R discs.
Copying data from a digital camcorder using a
DV input jack
Record DV Device video onto HDD and DVD-RAM/
-RW/-R discs using the DV input jack
(IEEE 1394-4pin/4pin). (See page 62)
High quality progressive scan
Copy between HDD and DVD
You can copy recordings from the HDD to recordable
DVD, or from DVD to the HDD.
You can only copy in the same record mode as source
title.
Progressive scanning provides high resolution and
flicker free video. The 10-bit 54-MHz DAC and 2D Y/C
Separating Circuitry provides the highest image
playback and recording quality. (See pages 33~34)
DivX Certification
Simultaneous Recording and Playback
Playback and recording for both the DVD and the
built-in hard disk drive (HDD) are completely
independent. For example you can record a broadcast
programme to either a recordable DVD or the HDD,
while watching another recording you already made on
the same DVD or on the HDD.
DivX, DivX Certified, and associated
logos are trademarks of DivX Networks,
Inc and are used under licence.
EZ Record Mode
This function allows you Initialise and Finalise a disc
automatically. (See page 29)
High quality digital audio and video recording
and playback
You can record up to approximately 16-hours of video
on a double side 9.4GB DVD-RAM disc, up to 15-hours
on a dual-layer 8.5GB DVD-R disc, and up to 8-hours
on a 4.7GB DVD-RAM/-RW/-R disc, depending on the
recording mode.
Selectable Recording Mode
You can set your HDD & DVD RECORDER to one of four
different recording speeds, each varying in recording
quality and length. EP (6Hr or 8Hr) mode yields the most
recording time, LP & SP modes provide less recording
time with higher quality recording, XP mode gives you the
highest quality recording.
The dual layer DVD-Rs have approximately double the
capacity of single layer DVD-Rs. (See page 36)
English - 10
01392A_HR750_XEU-ENG-0423.indd 10
2007-04-24
9:31:32
Copyright
©2007 Samsung Electronics Co.
All rights reserved; No part or whole of this user’s
manual may be reproduced or copied without the prior
written permission of Samsung Electronics Co.
Make sure to check the following terms before
reading the user manual.
Icons that will be used in manual
Icon
S
Z
X
C
V
B
G
A
D
J
M
N
Term
Definition
This involves a function available
HDD
on the HDD.
This involves a function available
DVD
on DVD or DVD±R/-RW(V) discs
that have been finalised.
This involves a function available
RAM
on DVD-RAM.
This involves a function available
-RW
on DVD-RW.
This involves a function available
-R
on DVD-R.
This involves a function available
CD
on a data CD (CD-R or CD-RW).
This involves a function available
JPEG
on CD-R/-RW, DVD±R/±RW/
-RAM discs or HDD.
This involves a function available
MP3
on CD-R/-RW, DVD±R/±RW/
-RAM discs or HDD.
This involves a function available
DivX
on CD-R/-RW, DVD±R/±RW/
-RAM discs or HDD.
This involves a case where a
Caution function does not operate or
settings may be cancelled.
This involves tips or instructions
NOTE
on the page that help each
function operate.
One-Touch A function that can be operated by
button
using only one button.
About the use of this user’s manual
1) Be sure to be familiar with Safety Instructions
before using this product. (See pages 2~7)
2) If a problem occurs, check the Troubleshooting.
(See pages 96~97)
Getting Started
Before reading the user’s manual
How to use the HDD & DVD RECORDER
Step 1: Select the disc type or HDD
Please check available disc type before recording.
• DVD-HR749 / DVD-HR750
If you want to repeatedly record on the same disc or
you want to edit the disc after recording, select a
rewritable DVD-RW or DVD-RAM type disc. If you
want to save a recording without any changes, choose
a non-rewritable DVD-R. You can record files directly
to the built-in HDD or edit a recorded file.
Step 2: Format the disc to start recording
Unlike a VCR, the HDD & DVD RECORDER
automatically starts formatting when an unused disc is
inserted. This is required for the preparation of
recording on a disc.
Using the HDD
Formatting unnecessary.
Using a DVD-RAM
This type of disc can be formatted in DVD-Video
Recording format (VR mode). You can edit recorded
images and create a playlist in a specific sequence
according to your requirements.
Using a DVD-RW
This type of disc can be formatted in either DVD-Video
format (V mode) or DVD-Video Recording format (VR
mode). For an unused disc, a message that asks
whether to initialize a disc or not. If you select
“DVD-VR” or “DVD-V”, initialising will be started. You
can play a Video mode disc on various DVD
components. A VR mode disc allows more varied
editing.
English - 11
01392A_HR750_XEU-ENG-0423.indd 11
2007-04-24
9:31:33
Getting Started
Using a DVD-R
Step 5: Editing a recorded disc
Formatting disc is unnecessary and only V Mode
Recording is supported. You can play these type of
discs on various DVD components only when they
have been finalised.
Editing on discs is easier than conventional video
tapes. The HDD & DVD RECORDER supports many
different edit functions, possible only with DVDs and
HDD.
M  You can only use either the VR or Video mode
on a DVD-RW, but not both at the same time.
 You can format a DVD-RW to V or VR mode
using Disc Manager. It should be noted that
the disc’s data will be lost when changing
formats.
Step 3: Recording
With a simple and easy edit menu, you can operate
various edit functions, such as delete, copy, rename,
lock, etc., on a recorded title.
Creating a playlist (DVD-RAM/-RW in VR mode,
HDD)
With this HDD & DVD RECORDER, you can create a
new playlist on a disc and edit it without the original,
pre-existing recording.
Step 6: Finalising & Playing on other
DVD components
There are two different recording methods, Direct
Recording and Timer Recording. Timer recording is
classified as follows:
Recording mode : XP (high quality mode), SP
(standard quality mode), LP (long recording mode),
and EP (extended mode) according to the recording
mode. When recording is set in the FR mode, the best
quality picture is recorded with regards to the
remaining time on the disc.
To play your DVD on other DVD components, finalising
may be necessary. First, finish all editing and recording
operations, then finalise the disc.
When using a DVD-RW disc in VR Mode
DVD discs recorded in VR mode can only be played
back in DVD recorders, not players.
When using a DVD-RW disc in Video Mode
Step 4: Playing
You can select the title you want to play in a displayed
menu and then immediately start playback.
A DVD consists of sections, called titles, and subsections, called chapters.
The disc should be finalised first to enable playback on
anything other than this HDD & DVD RECORDER. No
more editing or recording can be made on the disc
once it has been finalised.
To enable recording on the disc again, the disc must
be unfinalised.
When using a DVD-R disc
During recording, a title is created between two points
where you start and stop recording.
Chapters will be created automatically when you
finalise recording on DVD-RW/-R discs in Video mode.
The chapter’s length (interval between chapters) varies
according to the recording mode.
You should finalise the disc to play it on a component
other than this HDD & DVD RECORDER. You cannot
edit or record on the disc once it has been finalised.
M  You can finalise the disc automatically using
EZ Record function. (See page 29)
English - 12
01392A_HR750_XEU-ENG-0423.indd 12
2007-04-24
9:31:33
Preparing the Remote Control
Install Batteries in the Remote Control
Accessories
Check for the supplied accessories below.
• Open the battery cover on the back of the remote
control.
• Insert two AAA batteries. Make sure that the
polarities (+ and –) are aligned correctly.
• Replace the battery cover.
Getting Started
Unpacking
If the remote does not operate properly:
Video/Audio Cable
RF Cable for TV
•
•
•
•
Check the polarity + – of the batteries (Dry-Cell)
Check if the batteries are drained.
Check if remote sensor is blocked by obstacles.
Check if there is any fluorescent lighting nearby.
Dispose of batteries according to local environmental
regulations. Do not put them in the household trash.
Remote Control
Batteries for Remote
Control (AAA Size)
Instruction Manual
Quick Guide
To determine whether your television is
compatible, follow the instructions below.
1. Switch your television on.
2. Point the remote control towards the television.
3. Press and hold the TV STANDBY/ON button and
enter the two-figure code corresponding to the
brand of your television, by pressing the appropriate
number buttons.
English - 13
01392A_HR750_XEU-ENG-0423.indd 13
2007-04-24
9:31:34
Getting Started
Controllable TV Codes
BRAND
BUTTON
BRAND
BUTTON
SANYO
41, 42, 43, 44, 48
SAMSUNG
01, 02, 03, 04, 05, 06, 07, 08, 09
SCHNEIDER
6
AIWA
82
SELECO
74
ANAM
10, 11, 12, 13, 14, 15, 16, 17, 18
SHARP
36, 37, 38, 39, 48
BANG & OLUFSEN
57
SIEMENS
71
BLAUPUNKT
71
SINGER
57
BRANDT
73
SINUDYNE
57
BRIONVEGA
57
SONY
35, 48
CGE
52
TELEAVA
73
CONTINENTAL
EDISON
75
TELEFUNKEN
67, 73, 75, 76
THOMSON
72, 73, 75
DAEWOO
19, 20, 23, 24, 25, 26, 27, 28, 29,
30, 31, 32, 33, 34
EMERSON
64
FERGUSON
73
FINLUX
06, 49, 57
FORMENTI
57
FUJITSU
84
GRADIENTE
70
GRUNDIG
49, 52, 71
HITACHI
60, 72, 73, 75
IMPERIAL
52
JVC
61, 79
LG
06, 19, 20, 21, 22, 78
LOEWE
06, 69
LOEWE OPTA
06, 57
MAGNAVOX
40
METZ
57
MITSUBISHI
06, 48, 62, 65
MIVAR
52, 77
NEC
83
NEWSAN
68
NOBLEX
66
NOKIA
74
NORDMENDE
72, 73, 75
PANASONIC
53, 54, 74, 75
PHILIPS
06, 55, 56, 57
PHONOLA
06, 56, 57
PIONEER
58, 59, 73, 74
RADIOLA
06, 56
RADIOMARELLI
57
RCA
45, 46
REX
74
SABA
57, 72, 73, 74, 75
SALORA
74
THOMSON ASIA
80, 81
TOSHIBA
47, 48, 49, 50, 51, 52
WEGA
57
YOKO
6
ZENITH
63
Result: If your television is compatible with the remote
control, it will switch off.
It is now programmed to operate with the
remote control.
M  If several codes are indicated for your
television brand, try each one in turn until you
find one that works.
 If you replace the remote control’s batteries,
you must set the brand code again.
Then you can control the television using the
following buttons after pressing the TV button.
Button
Function
TV STANDBY/ON Used to switch the television on and off.
INPUT SEL.
Used to select an external source.
Used to adjust the volume of the television.
TV VOL (+ –)
Used to select the desired channel.
PROG (,.)
TV MUTE
Number
Used to toggle the sound on and off.
Used to input number directly.
M  The functions listed above will not necessarily
work on all televisions. If you encounter
problems, operate the television directly.
English - 14
01392A_HR750_XEU-ENG-0423.indd 14
2007-04-24
9:31:35
Getting Started
Description
Front Panel
< DVD-HR749 >
< DVD-HR750 >
1. STANDBY/ON button
Turns the HDD & DVD RECORDER on and off.
9. HDD button
Select HDD mode.
2. DISC TRAY
Opens to accept a disc.
10. PROG buttons
Select TV preset Channels. Same as PROG
button on the remote control.
3. OPEN/CLOSE button
Opens and closes the disc tray.
11. REC button
Starts recording.
4. DISPLAY
Displays the playing status, time, etc.
12. STOP button
Stops disc playback.
5. AV 3 INPUT
Connect external equipment.
6. DV-INPUT
Connect external digital equipment with a DV jack.
(such as a camcorder)
7. P.SCAN button
Selects the progressive scan mode.
13. PLAY/PAUSE button
Plays a disc or pauses playback.
14. SEARCH/SKIP buttons
Goes to the next title/chapter/track or goes back to
the previous title/chapter/track.
8. DVD button
Select DVD mode.
English - 15
01392A_HR750_XEU-ENG-0423.indd 15
2007-04-24
9:31:35
Getting Started
Rear Panel
Fan
The fan always revolves when the power is on.
Ensure a minimum of 10 cm clear space on all sides of
the fan when installing the product.
1. DIGITAL AUDIO OUT(OPTICAL)
Connects to an amplifier having a digital optical
audio input jack.
5. S-VIDEO OUT
Connects the input of external equipment using an
S-Video cable.
2. DIGITAL AUDIO OUT(COAXIAL)
Connects to an amplifier having a digital coaxial
audio input jack.
6. COMPONENT VIDEO OUT
Connects to equipment having Component video
input.
3. AUDIO OUT
Connects to the audio input of external equipment
using audio cables.
7. AV1(TV) OUTPUT SCART connector
4. VIDEO OUT
Connects the input of external equipment using a
Video cable.
8. AV2(EXT) INPUT SCART connector
9.
In from aerial connector
10.
Out to TV connector
M  The Antenna connection does not pass the
output signal of the DVD. To watch DVD/HDD
playback your TV, you must connect audio/
video or Scart cables.
Front Panel Display
1. Lights when a disc is loaded.
5. Playing time/clock/current status indicator.
2. Lights in the record mode.
6. Lights in the progressive scan mode.
3. Lights when a HDD/DVD is selected.
7. Lights to indicate the timer record mode.
4. Lights when a DVD-RAM/-RW/-R disc is loaded.
English - 16
01392A_HR750_XEU-ENG-0423.indd 16
2007-04-24
9:31:37
Tour of the Remote Control
1. DVD button
Press this to operate DVD.
2. TV button
Press this to operate TV.
3. STANDBY/ON button
4. NUMBER buttons
5. TV/DVD button
6. SUBTITLE button
Press this to switch the DVD’s subtitle language.
7. REVERSE/FORWARD SKIP buttons
Press to skip backwards or forwards.
8. STOP button
Press to stop a disc.
9. REVERSE/FORWARD SEARCH buttons
Press to search a disc backwards or forwards.
10. TV VOL button
TV volume adjustment.
11. MENU button
Brings up the HDD & DVD RECORDER’s setup menu.
12. OK/DIRECTION buttons (▲▼◄► buttons)
13. INFO button
This will display current setting or disc status.
14. TITLE LIST/DISC MENU button
Use this to enter the View Recording list/disc menu.
15. COLOUR button : RED(A), GREEN(B),
YELLOW(C), BLUE(D)
Allows access to common function of HDD & DVD
RECORDER.
16. COPY button
Press this when you copy DVD to HDD and
vice-versa.
To start copying, press the COPY button on the
title list screen or press the COPY button during
the playback.
17. REC button
Use to make a recording on HDD/DVD-RAM/-RW/-R
discs.
18. MARKER button
Use this to bookmark a position while playing a disc.
19. HDD button
Press this to operate HDD.
20. INPUT SEL button
Select input signal in external input mode (PROG,
AV1, AV2, AV3 or DV input)
21. OPEN/CLOSE button
To open and close the disc tray.
22. TV STANDBY/ON button
23. REPEAT A-B button
Allows you to repeat a title, chapter, track or disc.
24. REPEAT button
Allows you to repeat a title, chapter, track or disc.
25. PLAY/PAUSE button
Press to play/pause a disc.
26. PROG button
Use this to select a TV programme.
27. TV MUTE/AUDIO button
In TV mode, this operates as sound mute.
Use this to access various audio functions on a
disc (DVD mode).
28. RETURN button
29. EXIT button
30. PLAY LIST/TITLE MENU button
Use this to return to the Title menu, or to view the
recorded files list.
31. TIMER button
Press to directly enter the Timer Recording Mode
menu.
32. REC PAUSE/TIME SHIFT button
Use this to pause during recording.
In TV mode, use this to operate Time shift
function.
33. REC MODE button
Use this to set the desired Recording time and
picture quality. (XP/SP/LP/EP).
Getting Started
Your HDD & DVD RECORDER remote control will work with Samsung televisions and compatible brands.
English - 17
01392A_HR750_XEU-ENG-0423.indd 17
2007-04-24
9:31:37
Connecting & Setting Up
Connecting & Setting Up
Connecting the HDD & DVD RECORDER
This section involves various methods of
connecting the HDD & DVD RECORDER to other
external components and required initial setting
modes.
Additional connections
You can connect your HDD & DVD RECORDER to
a satellite or digital tuner.
You can connect your HDD & DVD RECORDER to the
television using the SCART cable if the appropriate
input is available on the television.
1. Connect the RF cable as shown.
2. Connect one end of the SCART cable to the AV1
socket on the rear of the HDD & DVD RECORDER.
3. Plug the other end into the appropriate connector
on the television.
4. Plug in the HDD & DVD RECORDER and TV
5. Turn on the HDD & DVD RECORDER and TV.
6. Press the INPUT SEL. button on your TV remote
control until the Video signal from the HDD & DVD
RECORDER appears on the TV screen.
1
External device (VCR/Satellite receiver)
2
- DVD mode
To RF IN
1. Connect the AV2 connector of HDD & DVD
RECORDER and VCR/Satellite receiver or digital
tuner using a SCART cable.
2
1
2. Connect the AV1 connector to the SCART AV
connector on TV.
To TV
3. Turn on the HDD & DVD RECORDER, VCR/
Satellite receiver or digital tuner and TV.
3
4. Set Input mode on AV2.
RF Cable
- TV mode
1. Press the TV/DVD button on remote control, then
“TV” appear on Front LED display. (or turn off HDD
& DVD RECORDER.)
To ANT INPUT
M  The RF cable connection of this product sends
only signals of TV. You must connect SCART
cable or Audio/Video cables to watch a DVD
from your HDD & DVD RECORDER.
2. You can watch programmes from a satellite or
digital tuner connected to this HDD & DVD
RECORDER, even when the HDD & DVD
RECORDER is turned off.
 TV mode : Press the TV/DVD button on
remote control, then “TV” appear on Front LED
display (or turn off HDD & DVD RECORDER).
Then you can watch programmes received
through TV.
English - 18
01392A_HR750_XEU-ENG-0423.indd 18
2007-04-24
9:31:38
Case 1 : Connecting to a Video
(Composite) output jack
Other type of connecting the Video
output cable
There are several ways to output video signal not
using scart cables. Select one of the following
video connecting that best suits you below.
• Case 1 : Connecting to a Video (Composite) output
jack
1. Connect a video (Yellow) cable between the VIDEO
(yellow) OUT jack on HDD & DVD RECORDER
and VIDEO (yellow) INPUT jack on your TV (or AV
amplifier).
• You will enjoy regular quality images.
• Case 2 : Connecting to an S-Video output jack
• Case 3 : Component Video output jacks
S-Video, Component video and Progressive
Output Modes
• S-Video and Component video output are available
only if your TV supports S-Video input or Component
video input, respectively. If S-Video or Component
video output does not work, check the TV
connections and the TV input selection settings.
• Progressive Scan Output (576P)
Consumers should note that not all high definition
television sets are fully compatible with this product
and may cause artifacts to be displayed in the
picture, in case of 576 progressive scan picture
problems, It is recommended that the user switch the
connection to the ‘standard definition’ output. If there
are questions regarding our TV set compatibility with
this model 576P HDD & DVD RECORDER, please
contact our customer service centre.
Yellow
Video/Audio Cable
• Compared to standard interlaced video, progressive
scan doubles the amount of video lines fed to your
TV, resulting in a more stable, flicker-free, clear
image than interlaced video. This is only available
with TVs that support progressive scan.
Connecting & Setting Up
2. Connect audio cables (white and red) between the
AUDIO OUT jacks on the HDD & DVD RECORDER
and AUDIO IN jacks on TV (or AV amplifier).
(See pages 21~22)
Yellow
English - 19
01392A_HR750_XEU-ENG-0423.indd 19
2007-04-24
9:31:40
Case 2 : Connecting to an S-Video
output jack
Case 3 : Component Video output
jacks
1. Connect an S-Video cable (not included) between
the S-VIDEO OUT jack on HDD & DVD
RECORDER and S-VIDEO INPUT jack on your TV
(or AV amplifier).
1. Connect Component video cables(not supplied)
between the COMPONENT OUT(Y, PB, PR) jacks
on HDD & DVD RECORDER and COMPONENT
IN(Y, PB, PR) jacks on your TV.
Connecting & Setting Up
• You will enjoy high quality images.
2. Connect audio cables (white and red) between the
AUDIO OUT jacks on HDD & DVD RECORDER
and AUDIO IN jacks on TV (or AV amplifier).
(See pages 21~22)
• You will enjoy high quality and accurate colour
reproduction images.
2. Connect audio cables (white and red) between the
AUDIO OUT jacks on the HDD & DVD RECORDER
and AUDIO IN jacks on TV (or AV amplifier).
(See pages 21~22).
3. After connecting, refer to the pages 33~34.
Green
Blue
Red
Green
Blue
Red
M  Make sure that the colour coded connections
match. The Y, PB, PR component output jacks
of your HDD & DVD RECORDER must be
connected to the exact corresponding
component input jacks on your TV.
 Progressive setting is only available when the
Video Out is set to Component.
(See pages 33~34)
English - 20
01392A_HR750_XEU-ENG-0423.indd 20
2007-04-24
9:31:41
Case 2 : Connecting to a stereo
amplifier with AV output jacks
Other type of connecting the Audio
output cable
There are several ways to output audio signal not
using scart cables. Select the audio connection
that best suits you below.
If your stereo amplifier only has AUDIO INPUT jacks
(L and R), use the AUDIO OUT jacks
Connecting & Setting Up
• Case 1 : Connecting to your TV
• Case 2 : Connecting to a stereo amplifier with AV
output jacks
• Case 3 : Connecting to an AV amplifier with a digital
output jack
Manufactured under licence from Dolby
Laboratories. “Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
Red
White
Red
White
“DTS” and “DTS Digital Out” are trademarks of
DTS, Inc.
Case 1 : Connecting to your TV
If your TV has audio input jacks, use this connection.
Front(L)
speaker
Yellow
White
Red
Yellow
Front(R)
speaker
White
Red
English - 21
01392A_HR750_XEU-ENG-0423.indd 21
2007-04-24
9:31:43
Connecting & Setting Up
Case 3: Connecting to an AV amplifier
with a digital output jack
If your AV amplifier has a Dolby Digital, MPEG2 or
DTS decoder and a digital input jack, use this
connection. To enjoy Dolby Digital, MPEG2 or DTS
sound, you will need to set up the audio settings.
According to your amplifier, connect to an optical cable
or a coaxial cable. (See pages 30~31)
Connecting to AV 3 IN, DV input jack
This allows you to connect your HDD & DVD
RECORDER to other external devices and view or
record their outputs.
• Case 1 : Connecting a VCR, Set-Top Box(STB),
DVD player or Camcorder to the AV 3 IN
jacks
• Case 2 : Connecting a DV Device to the DV IN jack
Case 1 : Connecting a VCR, Set-Top
Box(STB), DVD player or Camcorder
to the AV 3 IN jacks
Connecting a VCR or external device to AV 3 IN jacks
of the HDD & DVD RECORDER. You can record from
connected equipment (VCR, STB, DVD player or
Camcorder).
or
Camcorder
Rear (L)
VCR
Rear (R)
Subwoofer
DVD
Centre
Red
Front (R)
White
Yellow
STB
Front (L)
Yellow
White
Red
M  AV 3 in selection will be automatically done.
If the input is not selected automatically, use
INPUT SEL. button to select proper input.
 Copy protected content cannot be recorded.
English - 22
01392A_HR750_XEU-ENG-0423.indd 22
2007-04-24
9:31:44
Case 2 : Connecting a Camcorder to
the DV IN jack
If your digital camcorder has a DV output jack, connect
it to the DV input jack of your HDD & DVD
RECORDER.
Connecting & Setting Up
Camcorder
M  If the input is not selected automatically, use
INPUT SEL. button to select proper input.
English - 23
01392A_HR750_XEU-ENG-0423.indd 23
2007-04-24
9:31:47
System Setup
On-Screen Menu Navigation
HDD & DVD RECORDER
HDD
Library Title
Timer Record
Disc Manager
Library
|
DivX
|
Music
|
Photo
|
Setup
mMOVE
sSELECT
rRETURN
eEXIT
The on-screen menus allow you to enable or disable various
functions on your HDD & DVD RECORDER.
Press the MENU button to open the on-screen menu and then use
the following buttons to navigate through the on screen menus.
1. ▲▼, ◄► buttons
Press these buttons on the remote control to move the selection bar
▲▼, ◄► to cycle through the menu options.
2. OK button
Press this button on the remote control to confirm any new settings.
System Setup
3. RETURN button
Press this button on the remote control to return to the Previous
menu screen displayed or to exit the on-screen menu.
4. EXIT button
Press this button to exit the on-screen MENU.
Plug & Auto Setup
Your HDD & DVD RECORDER will automatically set itself up when
it is plugged in for the first time. TV stations and clock will be
stored in memory. The process takes a few minutes. Your HDD &
DVD RECORDER will then be ready for use.
1. Connect the RF cable as indicated on page 18.
(Connecting Your HDD & DVD RECORDER to the TV Using the RF
Cable and scart cable.)
Auto setup will be started.
Yes
2. Plug the HDD & DVD RECORDER into the mains. “AUTO” in the
front panel display flickers.
No
3. Press the OK button to start the auto setup.
4. Auto channel scan will be started.
• The number of stations automatically stored by the HDD & DVD
RECORDER depends on the number of stations that it has found.
Auto Setup
Please wait.
63%
Stop
5. After auto channel scan is completed, auto clock setting will be
started automatically in 10 seconds. If you want to start auto clock
setting immediately, press OK button. If you do not want to do auto
clock setting, select No using the ◄► buttons, then press the OK
button.
Auto channel scan completed successfully.
Press the [OK] button to auto clock set.
Yes
No
English - 24
01392A_HR750_XEU-ENG-0423.indd 24
2007-04-24
9:31:48
6. Wait until current date and time are displayed automatically. If you
want to exit auto clock setting, press MENU button.
M  Now, HDD & DVD RECORDER is ready for use. Function for
Please wait. Now setting the clock.
If you want to exit clock setting,
press the [MENU] button.
“Plug & Auto Setup” is fixed already. So if you want to change
this fixed one, you can change it by Presetting the Stations in
OSD “Channel Set - Manual Setup” menu. (See pages 26~27)
 Auto setup function can be performed by pressing STOP ( )
on the unit continuously for 5 seconds or more during power off
with no disc inserted.
7. Check the date and time.
• If it is : Correct, press OK button then the date and time will be
saved. If you don’t press the OK button, the date and time will be
saved automatically after 5 seconds.
Clock Set
mo.
da.
yr.
JAN
01
2007
hr.
12
min. Auto
00
On
Monday
System Setup
• If it is : Incorrect, input correct Month, Day, Year, Hour or Minute
using ▲▼, ◄► buttons or number buttons. Press OK button then
the date and time will be saved. When you need to change clock
setting, you can set up it manually.
Setting the Clock
HDD & DVD RECORDER
HDD
Library System
Timer Record
Disc Manager
Setup
Setup
|
Clock Set
|
Channel Set
|
Language
|
|
Audio
|
Video
1
Parental Lock
mMOVE
sSELECT
|
rRETURN
eEXIT
HDD & DVD RECORDER
HDD
Library System
Timer Record
Disc Manager
Setup
Setup
|
Clock Set
|
Channel Set
|
Language
|
Audio
|
|
Video
1
Parental Lock
mMOVE
sSELECT
|
rRETURN
eEXIT
HDD & DVD RECORDER
HDD
Clock Set
Library
Setup
mo.
da.
yr.
JAN
01
2007
hr.
12
min. Auto
00
On
Monday
<MOVE
1. With the unit in Stop mode, press the MENU button.
2. Press the ▲▼ buttons to select Setup, then press the OK or ►
button.
3. Press the ▲▼ buttons to select Clock Set, then press the OK or ►
button.
Press the ▲▼◄► buttons to input Month, Day, Year, Hour or
Minute. Press the number buttons to input clock data directly.
The day of the week is displayed automatically.
4. Press the OK button, then the date and time will be saved. If you
don’t press the OK button, it will not be saved.
M  You must have the RF cable connected to set the Auto Clock.
(See page 18)
Timer Record
Disc Manager
This menu is used to set the current time.
You need to set the time to use timer recording.
sSELECT
rRETURN
eEXIT
 The HDD & DVD RECORDER automatically sets the clock
according to the time signal broadcast between the channels
PR1 to PR5. If you do not need the Auto Clock Set function,
select Off.
English - 25
01392A_HR750_XEU-ENG-0423.indd 25
2007-04-24
9:31:49
HDD & DVD RECORDER
HDD
Library Auto Setup
Channel Set
|
|
Manual Setup
Timer Record
Disc Manager
Auto Setup
Setup
mMOVE
Channel Set
sSELECT
rRETURN
eEXIT
This feature allows you to manually set the HDD & DVD
RECORDER tuner band to Antenna or Cable, whichever you
connected to the Antenna In jack during initial setup.
1. With the unit in Stop mode, press the MENU button.
2. Press the ▲▼ buttons to select Setup, then press the OK or ►
button.
Auto Setup
Please wait.
3%
Stop
3. Press the ▲▼ buttons to select Channel Set, then press the OK or
► button.
System Setup
4. Press the ▲▼ buttons to select Auto Setup, then press the OK or
► button.
The message “Your data will be lost. Press [OK] to continue,
[RETURN] to exit.” is displayed.
5. Press the OK button. Channel scan will be started.
• The first frequency band is scanned and the first station found is
displayed and stored. And the HDD & DVD RECORDER
searches for the second station and so on.
• The number of stations automatically stored by the HDD & DVD
RECORDER depends on the number of stations that it has found.
M  Press the OK button to stop the Auto Setup
Manual Setup
Manual Setup
CH
002
004
-----------
PR
01
02
03
04
05
06
07
Edit
Delete
Manual Setup
PR
01
CH
002
Name
----
MFT
Save
mMOVE
sSELECT
Name
---------------------Swap
You can add preset channel that Auto Channel Search missed.
And you can delete a channel you wish to remove. You can
programme the order of channels.
1. With the unit in Stop mode, press the MENU button.
2. Press the ▲▼ buttons to select Setup, then press the OK or ►
button.
3. Press the ▲▼ buttons to select Channel Set, then press the OK or
► button.
4. Press the ▲▼ buttons to select Manual Setup, then press the OK
or ► button.
5. Press the ▲▼ buttons to select a PR(programme) you wish to edit,
delete, or swap, then press the COLOUR button.
Select Edit, Delete or Swap.
• In case of Edit (RED(A) button) : You can add or edit
PR(programme) information. After change PR informations (CH.,
Name, MFT), select Save, then press the OK button.
- CH : Tune the channel using ◄► buttons.
- Name : Display station name automatically detected in
broadcasting signal. If not detected, you can edit name
by using ▲▼◄► buttons.
- MFT(Manual Frequency Tunning) : You can tune up the
channel frequency better using ◄► buttons.
• In case of Delete (GREEN(B) button) : the channel information
of selected PR(programme) will be removed.
English - 26
01392A_HR750_XEU-ENG-0423.indd 26
2007-04-24
9:31:51
• In case of Swap (YELLOW(C) button) : You can swap the
channel information of two PR(programme). For example, if you
wish to swap PR2 and PR5, select swap at PR2, then press the
OK button at PR5.
HDD & DVD RECORDER
HDD
Library Audio
Timer Record
Disc Manager
Language
: Original
|
Subtitle
: Automatic |
Disc Menu
: English
|
Menu
: English
|
Setup
mMOVE
Setting up the Language Options
If you set the language options, in advance, they will come up
automatically every time you watch a movie.
1. With the unit in Stop mode, press the MENU button.
sSELECT
rRETURN
eEXIT
2. Press the ▲▼ buttons to select Setup,
then press the OK or ► button.
4. Press the ▲▼ buttons to select the desired language option, press
the OK or ► button.
• Audio : For the disc audio language.
• Subtitle : For the disc subtitles.
System Setup
3. Press the ▲▼ buttons to select Language,
then press the OK or ► button.
Language setup menu will be displayed.
• Disc Menu : For the disc menu contained on the disc
• Menu : For the on-screen menu of your HDD & DVD
RECORDER.
5. Press the ▲▼ buttons to select the desired language, then press
the OK or ► button.
M  If the selected language is not recorded on the disc, the
original pre-recorded language is selected.
 The selected language will only appear if it is supported on the
disc.
HDD & DVD RECORDER
HDD
Library Auto Power Off
: Off
|
Chapter Creator
: Off
|
EP Mode Time
: 6 Hours
|
EZ Record
: Off
|
Timer Record
Disc Manager
Setup
mMOVE
DivX(R) Registration
sSELECT
rRETURN
System
|
eEXIT
Setting up the System Options
This function allows you to setup the system setting.
1. With the unit in Stop mode, press the MENU button.
2. Press the ▲▼ buttons to select Setup, then press the OK or ►
button.
3. Press the ▲▼ buttons to select System, then press the OK or ►
button.
4. Press the ▲▼ buttons to select the desired system option, then
press the OK or ► button.
5. Press the ▲▼ buttons to select the desired item, then press the OK
or ► button.
English - 27
01392A_HR750_XEU-ENG-0423.indd 27
2007-04-24
9:31:53
Auto Power Off Setting
HDD & DVD RECORDER
HDD
Library Auto Power Off Off
Chapter Creator 2 Hours
Timer Record
EP Mode Time 6 Hours
Disc Manager
EZ Record
Setup DivX(R) Registration
mMOVE
sSELECT
System
: Off
|
: Off
|
: 6 Hours
|
: Off
|
|
rRETURN
eEXIT
This feature automatically turns off your HDD & DVD RECORDER,
if you do not press any button for the selected time.
1. Press the ▲▼ buttons to select Auto Power Off, then press the OK
or ► button.
2. Press the ▲▼ buttons to select the desired item, then press the OK
or ► button.
• Off : Auto power off is disabled.
• 2 Hours : HDD & DVD RECORDER will automatically turn off for
2 hours after the last button is pressed.
• 6 Hours : HDD & DVD RECORDER will automatically turn off for
6 hours after the last button is pressed.
System Setup
• If the turn off time set with the Auto Power off function is reached
during playback or recording, the device will operate until the
playback or recording is finished.
HDD & DVD RECORDER
DVD-RW(V)
Library Auto Power Off
Timer Record
Disc Manager
Setup
mMOVE
System
: Off
|
Chapter Creator Off
EP Mode Time On
: Off
|
: 6 Hours
|
EZ Record
: Off
|
rRETURN
eEXIT
1/1
Jan/1/2007
17:30 PR1
Jan/1/2007
17:30 PR1
CV
(V-mode)
|
DivX(R) Registration
sSELECT
Automatic Chapter Creator
A DVD-Video consists of ‘Titles’ and ‘Chapters’.
When you record one programme, it makes one Title.
If you use this function, the Title will be divided into Chapters.
1. Press the ▲▼ buttons to select Chapter Creator, then press the
OK or ► button.
2. Press the ▲▼ buttons to select Off or On, then press the OK or ►
button.
• Off : Select if you do not want use Automatic Chapter Creator.
Previous
Top
• On : Select this option to use the Automatic Chapter Creator feature.
Next
Press the EXIT (
CHAPTER
1/1
) button to exit the menu.
3. Press the REC button to start recording.
(See page 58 about how to set recording speed)
The message “Do you want to create the chapter menu after this
recording?” is displayed.
4. Press the ◄► buttons to select OK, then press the OK button.
Previous
Top
Next
• A new chapter is created according to the selected recording
mode. A chapter will be about 5 minutes long in XP and SP, and
about 15 minutes long in LP and EP mode.
5. Press the STOP button to stop recording.
6. To display the created titles, finalise the disc (See page 94) and then
press the TITLE MENU button. The title menu will be displayed.
7. To display the created chapters, select the desired Title and then
press the DISC MENU button. The chapter menu for the selected
Title will be displayed.
J  The Automatic Chapter Creator function does not work during
Timer Recording or when you turn the power off.
English - 28
01392A_HR750_XEU-ENG-0423.indd 28
2007-04-24
9:31:54
EP Mode Time Setting
HDD & DVD RECORDER
HDD
Library Auto Power Off
Timer Record
Chapter Creator
EP Mode Time
Disc Manager
Setup
mMOVE
System
EZ Record
: Off
|
: On
|
6 Hours : 6 Hours
8 Hours : Off
|
|
DivX(R) Registration
sSELECT
|
rRETURN
eEXIT
You can select one of four recording modes by pressing the REC
MODE button repeatedly.
EP mode is one of four REC Mode (XP, SP, LP, EP).
In EP(Extended Play) mode, you can set recording time to 6 or 8
hours with this setting.
• 6 Hours
• 8 Hours
HDD & DVD RECORDER
HDD
Library Auto Power Off
: Off
|
Chapter Creator
: Off
|
EP Mode Time
: 6 Hours
|
EZ Record
: Off
|
Timer Record
Disc Manager
Setup
Off
On
DivX(R) Registration
System
sSELECT
CV
(V-mode)
|
|
mMOVE
EZ Record
rRETURN
eEXIT
This function allows you Initialise and Finalise a disc
automatically.
Disc Initialise (DVD-V)
Now, initialising..
2. Press the ▲▼ buttons to select On, then press the OK or ► button.
Press the EXIT ( ) button to exit the menu.
50%
System Setup
1. Press the ▲▼ buttons to select EZ Record, then press the OK or ►
button.
3. Insert a disc.
If the disc is new, it will initialise automatically.
4. Press the REC button.
5. EZ Record function will automatically Finalise the disc under the
following conditions.
Finalisation...
50%
• When you press the OPEN/CLOSE button on your HDD & DVD
RECORDER after recording on at least 70% of the disc. The tray
will open after the disc has been finalised.
• The above feature is available only when a DVD-RW(V) or
DVD-R disc is inserted.
M  If you insert a new DVD-RW disc, it will be formatted in V mode
after auto initialising.
 If you select off, you must initialise (see page 57) and finalise
the disc manually in the Disc Manager menu.(see page 94)
 The length of Recording is different according to recording
mode. (see page 36)
HDD & DVD RECORDER
HDD
Library Auto Power Off
: Off
|
DivX(R) Video Chapter
On Demand
Creator
: Off
|
Timer Record
System
EP Mode Time
: 6 Hours
Your registration code is: XXXXXXXX
Disc Manager
Record
: Off
To learn EZ
more
visit www.divx.com/vod
Setup DivX(R) Registration
OK
sSELECT
rRETURN
|
|
|
DivX(R) Registration
Please use the Registration code to register this HDD & DVD
RECORDER with the DivX(R) Video On Demand format. For more
information, visit www.divx.com/vod
eEXIT
English - 29
01392A_HR750_XEU-ENG-0423.indd 29
2007-04-24
9:31:56
HDD & DVD RECORDER
HDD
Library System
Timer Record
Disc Manager
Setup
Setup
|
Clock Set
|
Channel Set
|
Language
|
|
Audio
|
Video
1
Parental Lock
mMOVE
sSELECT
rRETURN
|
eEXIT
Setting up the Audio Options
You can connect the HDD & DVD RECORDER to an external amp
or Home theatre.
Allows you to setup the Audio device and sound status
depending on the audio system in use.
You can also set NICAM mode.
1. With the unit in Stop mode, press the MENU button.
2. Press the ▲▼ buttons to select Setup, then press the OK or ►
button.
3. Press the ▲▼ buttons to select Audio, then press the OK or ►
button.
4. Press the ▲▼ buttons to select the desired audio option, then press
the OK or ► button.
System Setup
5. Press the ▲▼ buttons to select the desired item, then press the OK
or ► button.
M  Press the RETURN or ◄ button to return to the previous
menu.
Press the EXIT (
HDD & DVD RECORDER
HDD
Library Digital Output
Timer Record
Disc Manager
Setup
mMOVE
DTS
Audio
: PCM
PCM
Bitstream: Off
|
|
DRC
: On
|
NICAM
: On
|
V-Mode Compatibility
: Off
|
sSELECT
rRETURN
eEXIT
) button to exit the menu.
Digital Output
• PCM : Select this when your equipment is not decode Dolby Digital
compatible.
• Bitstream : Outputs Dolby Digital (or MPEG-2) audio as bitstream.
Select this when your AV receiver or AV amplifier has a
Dolby Digital (or MPEG-2) Decoder.
M  Digital output setting is equally applied to both Dolby Digital
and MPEG-2 audio. LPCM sound track is always outputted as
PCM. It has no relation with Digital Output setting.
 Be sure to select the correct Digital Output or you will hear no
sound or a loud noise.
DTS
HDD & DVD RECORDER
HDD
Library Digital Output
Timer Record
: PCM
|
: Off
|
: On
|
NICAM
: On
|
V-Mode Compatibility
: Off
|
DTS
DRC
Disc Manager
Setup
mMOVE
Audio
sSELECT
Off
On
rRETURN
eEXIT
• Off : Doesn’t output DTS signal. Select this when your AV receiver
(or AV amplifier) does not have DTS decoder.
• On : Outputs DTS Bitstream via digital output when you play DTS
track. Select this only when your AV receiver (or AV amplifier)
have DTS decoder.
M  When DTS soundtrack is played, sound does not output from
AV Audio Output.
English - 30
01392A_HR750_XEU-ENG-0423.indd 30
2007-04-24
9:31:58
DRC
HDD & DVD RECORDER
HDD
Library Digital Output
Timer Record
DTS
DRC
Disc Manager
Setup
mMOVE
Audio
NICAM
Off
On
V-Mode Compatibility
sSELECT
Disc Manager
Setup
|
|
: On
|
: Off
|
eEXIT
Audio
: PCM
|
DTS
: Off
|
DRC
: On
|
NICAM
: On
|
: Off
|
Off
On
V-Mode Compatibility
sSELECT
rRETURN
eEXIT
This is only active when a Dolby Digital signal is detected.
• On : When Movie soundtracks are played at low volume or from
smaller speakers, the system can apply appropriate
compression to make low-level content more intelligible and
prevent dramatic passages from getting too loud.
• Off : You can enjoy the movie with the standard Dynamic Range.
NICAM
NICAM programmes are divided into 3 types. NICAM Stereo,
NICAM Mono and Bilingual (transmission in another language).
NICAM programmes are always accompanied by a standard mono
sound broadcast and you can select the desired sound by setting
NICAM on or off.
• On : NICAM mode
• Off : Only set at this position to record the standard mono sound
during a NICAM broadcast if the stereo sound is distorted due
to inferior reception conditions.
HDD & DVD RECORDER
HDD
Library Digital Output
Timer Record
Disc Manager
Setup
Audio
: PCM
|
DTS
: Off
|
DRC
: On
|
NICAM
: On
|
: Off
|
V-Mode Compatibility
Off
On
mMOVE
sSELECT
rRETURN
HDD & DVD RECORDER
HDD
Library Digital Output
Timer Record
Disc Manager
Setup
eEXIT
|
DTS
: Off
|
DRC
: On
|
NICAM
: On
|
V-Mode Compatibility
: On
|
sSELECT
V-Mode Compatibility
This feature is about the setup for selecting audios when
recording the NICAM STEREO (Multi-audio) broadcasting on HDD.
It does not affect to the direct DVD recording of a programme.
• Off : Both “Dual L” and “Dual R” of the multi-audio broadcasting are
recorded on HDD. Titles recorded on HDD under such setup
status cannot be copied to DVD-R or DVD-RW (V mode).
Audio
: PCM
Audio Selection Dual L : Dual L
Dual R
mMOVE
System Setup
mMOVE
|
rRETURN
HDD & DVD RECORDER
HDD
Library Digital Output
Timer Record
: PCM
: Off
: On
rRETURN
|
• On : Either “Dual L” or “Dual R” of the multi-audio broadcasting is
recorded on HDD. Titles recorded on HDD under such setup
status can be copied to DVD-R or DVD-RW (V mode). “Dual L”
and “Dual R” options can be selected from “Audio Selection.”
eEXIT
English - 31
01392A_HR750_XEU-ENG-0423.indd 31
2007-04-24
9:32:00
HDD & DVD RECORDER
HDD
Library System
Timer Record
Disc Manager
Setup
Setup
|
Clock Set
|
Channel Set
|
Language
|
|
Audio
|
Video
1
Parental Lock
mMOVE
sSELECT
rRETURN
|
eEXIT
Setting up the Video Options
This function allows you to setup the video setting.
This function depends on disc type. It may not work for some disc
types.
1. With the unit in Stop mode, press the MENU button.
2. Press the ▲▼ buttons to select Setup, then press the OK or ►
button.
3. Press the ▲▼ buttons to select Video, then press the OK or ►
button. Video setup menu will be displayed.
4. Press the ▲▼ buttons to select the desired video option, then press
the OK or ► button.
5. Press the ▲▼ buttons to select the desired item, then press the OK
or ► button.
System Setup
M  Press the RETURN or ◄ button to return to the previous
menu.
Press the EXIT (
HDD & DVD RECORDER
HDD
Library TV Aspect
Timer Record
Disc Manager
Video
: 4:3
Letter Box|
4:3 Letter
Box
4:3 Pan-Scan
3D Noise Reduction
: Off
|
16:9 Wide
Video Output
: Component |
Setup
mMOVE
sSELECT
rRETURN
eEXIT
) button to exit the menu.
TV Aspect
Depending on the type of television you have, you may want to
adjust the screen setting. (aspect ratio)
• 4:3 Letter Box : Select when you want to see the total 16:9 ratio
screen DVD supplies, even though you have a TV
with a 4:3 ratio screen. Black bars will appear at the
top and bottom of the screen.
• 4:3 Pan-Scan : Select this for conventional size TV when you want
to see the central portion of the 16:9 screen.
(Extreme left and right side of movie picture will be
cut off.)
• 16:9 Wide
HDD & DVD RECORDER
HDD
Library TV Aspect
Timer Record
Video
: 4:3 Letter Box|
3D Noise Reduction
Off
Video Output
On
Disc Manager
: Off
|
: Component |
: You can view the full 16:9 picture on your wide
screen TV.
3D Noise Reduction (motion adaptive noise reduction)
• Off : Normal
• On : Provides a clear picture through noise reduction (for recording).
Setup
mMOVE
sSELECT
rRETURN
eEXIT
English - 32
01392A_HR750_XEU-ENG-0423.indd 32
2007-04-24
9:32:03
Video Output
HDD & DVD RECORDER
HDD
Library TV Aspect
Timer Record
Video
: 4:3 Letter Box|
3D Noise Reduction
Video Output
Disc Manager
|
: Off
: Component |
Component
RGB
Setup
mMOVE
sSELECT
rRETURN
eEXIT
You can enjoy high quality image through RGB or Component
video connections. RGB video output is available connecting
scart jack(AV1) and component video output is available
connecting component(Y, PB, PR) jack. Only one of these signals
can be selected at one time.
• Component
• RGB
In Component mode, you can set video output to Progressive
(P.SCAN) or Interlace, see pages 33 to 34.
Available video output jacks are as follow.
Available Video Output Jack
Component Output
(Y, PB, PR)
|
|
(TV in progressive mode)
°
AV1 R, G, B
Scart Composite
°
°
|
|
°
°
Composite Video out
|
°
|
S-Video out
|
°
|
System Setup
Component mode
Setting mode
RGB Mode
Output jack
P.SCAN off mode (Interlace mode) P.SCAN on mode
Progressive scan
If your TV supports Progressive Scan, press the P.SCAN button
on the front of the HDD & DVD RECORDER.
To view ‘Progressive scan mode’, first connect the component
cable. (See page 20)
Be sure the Component cables are connected properly.
◆ Setting up the Progressive scan
Press [Yes] to confirm Progressive scan mode.
Otherwise, press [No].
Yes
No
1. With the unit in Stop mode, press the P.SCAN button on the front of
the HDD & DVD RECORDER.
The message “Press [Yes] to confirm Progressive scan mode.
Otherwise, press [No].” will appear.
2. Press the ◄► buttons to select Yes, and then press the OK button.
3. Set your TV to Progressive input (using the TV remote control.)
English - 33
01392A_HR750_XEU-ENG-0423.indd 33
2007-04-24
9:32:05
M  If the P.SCAN button on the HDD & DVD RECORDER’s front
panel is pressed during playback, the message “This function
is possible only on stop mode” appears on the screen.
 Progressive setting is only available when the HDD & DVD
RECORDER is in stop mode.
◆ Canceling the Progressive scan
Press [Yes] to confirm Interlace scan mode.
Otherwise, press [No].
Yes
No
1. With the unit in Stop mode, press the P.SCAN button on the front of
the HDD & DVD RECORDER.
The message “Press [Yes] to confirm Interlace scan mode.
Otherwise, press [No].” will appear.
2. Press the ◄► buttons to select Yes, and then press the OK button.
System Setup
3. Set your TV to Interlace input (using the TV remote control.)
M  Do not press the P.SCAN button if you are using a TV that
does not support Progressive mode as nothing will be
displayed on the screen.
 If you press the P.SCAN button by mistake when your TV does
not support Progressive mode, the mode will then need to be
released. To release the Progressive mode, press the P.SCAN
button on the front panel 3 times. The screen will recover after
the PS indicator on the front panel display turns off.
English - 34
01392A_HR750_XEU-ENG-0423.indd 34
2007-04-24
9:32:06
HDD & DVD RECORDER
HDD
Library System
Timer Record
Disc Manager
Setup
Setup
|
Clock Set
|
Channel Set
|
Language
|
Audio
|
|
Video
1
Parental Lock
mMOVE
sSELECT
Setting up the Parental Lock
|
rRETURN
eEXIT
Z
The Parental Lock function works in conjunction with DVDs that have
been assigned a rating which helps you control the types of DVDs
that your family watches. There are up to 8 rating levels on a disc.
1. With the unit in Stop mode, press the MENU button.
2. Press the ▲▼ buttons to select Setup, then press the OK or ►
button.
3. Press the ▲▼ buttons to select Parental Lock, then press the OK
or ► button.
When you operate your HDD & DVD RECORDER for the first time,
the “Create the Password” message will be displayed.
M  Press the RETURN or ◄ button to return to the previous menu.
Press the EXIT (
) button to exit the menu.
System Setup
4. Enter the 4-digit password using the number buttons on the remote
control.
The “Confirm the password” message will be displayed. Enter your
password again.
If you forgot your password
1. Remove the disc.
2. Press and hold the PROG (
5 seconds or more.
Timer Record
Disc Manager
Setup
Parental Lock
◄
HDD & DVD RECORDER
HDD
Library Rating Level
: Off
Off
Change PasswordLevel8 - Adults
Level7
Level6
Level5
Level4
Level3
Level2
sSELECT
rRETURN
HDD & DVD RECORDER
HDD
Library Rating Level
|
Timer Record
eEXIT
Parental Lock
: Level7
Change Password
|
Setup
sSELECT
rRETURN
1. Press the ▲▼ buttons to select Rating Level, then press the OK or
► button.
2. Press the ▲▼ buttons to select the rating level you want, then press
the OK or ► button.
For example, if you select up to Level 6, discs that contain Level 7,
8 will not play. A larger number indicates that the programme is
intended for adult use only.
Changing the Password
|
Disc Manager
mMOVE
Setting the Rating Level
|
►
mMOVE
) button on the front panel for
eEXIT
1. Press the ▲▼ buttons to select Change Password, then press the
OK or ► button.
2. Enter the 4-digit password using the number buttons on the remote
control. The “Confirm the password” message will be displayed.
3. Enter your password again using the number buttons on the remote
control.
M  After Rating Level has been set, you can change the password.
English - 35
01392A_HR750_XEU-ENG-0423.indd 35
2007-04-24
9:32:06
Playback
This section introduces basic functions of
playback and playback by disc type.
Read the following information before playing a
disc.
Disc types that can be played
Disc Types
DVD-VIDEO
Region code (DVD-Video only)
AUDIO-CD
Both the HDD & DVD RECORDER and the
discs are coded by region. These regional
codes must match in order for the disc to play.
If the codes do not match, the disc will not
play. The Region Number for this HDD & DVD
RECORDER is described on the rear panel of
the HDD & DVD RECORDER.
JPEG
MP3
DivX
Logos of Discs that can be played
Playback
Disc Shape
Single sided(12cm)
AUDIO Double sided(12cm)
VIDEO
Single sided(8cm)
Double sided(8cm)
Single sided(12cm)
AUDIO
Single sided(8cm)
Single sided(12cm)
JPEG Image
Single sided(8cm)
Single sided(12cm)
MP3 Audio
Single sided(8cm)
Single sided(12cm)
DivX Movie
Single sided(8cm)
AUDIO
VIDEO
Double sided(12cm)
(9.4GB)
AUDIO
VIDEO
DVD-RW
DTS
Recorded
content
Single sided(12cm)
(4.7GB)
DVD-RAM
Dolby Digital
Disc Logo
content
12cm (4.7GB)
Digital Audio
Single Layer(12cm)
(4.7GB)
AUDIO
VIDEO
DVD-R
Stereo
Dual Layer(12cm)
(8.5GB)
PAL broadcast
system in U.K, France,
Germany, etc.
CD-R/-RW
DVD-RAM/
-RW/-R
DivX
DVDHR749
MP3
HDD
DVDHR750
JPEG
MP3
DivX
AUDIO
VIDEO
–
Max. Playing Time
240 min.
480 min.
80 min.
160 min.
74 min.
20 min.
–
–
–
–
–
–
1 hr. (XP: Excellent Quality)
2 hrs. (SP: Standard Quality)
4 hrs. (LP: Long Playback)
6 or 8 hrs. (EP: Extended)
2 hrs. (XP: Excellent Quality)
4 hrs. (SP: Standard Quality)
8 hrs. (LP: Long Playback)
12 or 16 hrs. (EP: Extended)
1 hr. (XP: Excellent Quality)
2 hrs. (SP: Standard Quality)
4 hrs. (LP: Long Playback)
6 or 8 hrs. (EP: Extended)
1 hr. (XP: Excellent Quality)
2 hrs. (SP: Standard Quality)
4 hrs. (LP: Long Playback)
6 or 8 hrs. (EP: Extended)
1 hr. 50min (XP: Excellent Quality)
3 hrs. 40min (SP: Standard Quality)
7 hrs. 20min (LP: Long Playback)
11 or 14 hrs. 40min (EP: Extended)
–
Approx. 41
(XP: Excellent Quality)
Approx. 67
(SP: Standard Quality)
Approx. 133
(LP: Long Playback)
Approx. 199 or Approx. 264
(EP: Extended)
English - 36
01392A_HR750_XEU-ENG-0423.indd 36
2007-04-24
9:32:08
Discs that cannot be played
• DVD-Video with a region number other than “2” or “ALL”
• 3.9 GB DVD-R Disc for Authoring.
• DVD-RAM/-RW(VR mode) not recorded following the Video
Recording Standard
• A DVD-R/DVD-RW(V) disc which has been recorded and not
finalised in a different manufacturer’s recorder.
• DVD-ROM/PD/MV-Disc, etc
• CVD/CD-ROM/CDV/CD-G/CD-I
M  This HDD & DVD RECORDER can only operate with discs that
are compatible with DVD-RAM Standard Version 2.0.
 Playback and/or recording may not work for some types of discs,
or when specific operations, such as angle change and aspect
ratio adjustment, are being performed. Information about the discs
is written in detail on the box. Please refer to this if necessary.
 Do not allow the disc to become dirty or scratched, finger
prints, dirt, dust, scratches or deposits of cigarette smoke on
the recording surface may make it impossible to use the disc
for recording.
 DVD-RAM/-RW/-R discs may not be able to play on some
DVD players, depending on the player, disc and the condition
of the recording.
played and recorded using this product.
Playback
 Discs with NTSC programmes recorded on them cannot be
Playing a Disc
1. Press the OPEN/CLOSE button.
2. Place a disc gently into the tray with the disc’s label facing up.
3. Press the OPEN/CLOSE button to close the disc tray.
• Your HDD & DVD RECORDER closes the disc tray and plays the
disc automatically.
• The HDD & DVD RECORDER does not play discs automatically
after being powered on initially.
• When the HDD & DVD RECORDER is powered on and a disc is
in the tray, the unit will be activated and wait in stop status.
• Press the PLAY(
) button to start playback.
• If you want the unit to play automatically when it is powered on
with a disc in the unit, power on with the PLAY( ) button.
4. Press the STOP(
) button to stop playback.
M  When you stop playing back a disc, the HDD & DVD
RECORDER remembers where you stopped, so when you
press PLAY( ) button again, it will pick up where you left off.
(Unless the disc is removed or the HDD & DVD RECORDER is
unplugged, or if you press the STOP( ) button twice.)
English - 37
01392A_HR750_XEU-ENG-0423.indd 37
2007-04-24
9:32:10
J  Do not move your HDD & DVD RECORDER while playing, as
this may cause damage to the disc.
 Make sure to press the OPEN/CLOSE button to open or close
the disc tray.
 Do not push the disc tray while it is being opened or closed, as
this may cause a product malfunction.
 Do not place foreign materials on or in the disc tray.
 Some functions may perform differently or be disabled
depending on the disc type.
If this occurs, refer to the instructions written on the disc case.
 Be especially careful that children’s fingers are not caught
between the disc tray and the tray chassis when it closes.
 You must only insert one DVD disc at a time. Inserting two or
more discs will not allow playback and may cause damage to
the HDD & DVD RECORDER.
Using the Disc Menu & Title Menu
Playback
Some type of discs contain a dedicated menu system that allows
you to select special functions for title, chapter, audio track,
subtitle, film preview, information on characters, etc.
For DVD-VIDEO Disc
Z
 Disc Menu : Press the DISC MENU button to enter the disc menu
of the disc.
• Move to the setup menu related to playback operation.
• You can select audio language and subtitle etc. provided by the
disc.
 Title Menu : Press the TITLE MENU button to move to the title
menu of the disc.
• Press this button if the disc contains more than one title. Some
discs may not support the title menu functionality.
For HDD/DVD-RAM/-RW/-R Disc
SXCV
• Title List
Press the TITLE LIST button. Title List is a list of previously recorded
programmes. If a title is deleted, that title cannot be played again.
• Play List (DVD-RAM/-RW(VR))
Press the PLAY LIST button. This refers to a list of user-selected
titles. When one playlist is played, only the scene selected by the
user will play and then stop. Since only the information necessary for
playing a desired scene is included in a playlist, even if that playlist is
deleted, the original recording will not be deleted. (only VR mode)
English - 38
01392A_HR750_XEU-ENG-0423.indd 38
2007-04-24
9:32:10
Using the playback related buttons
Searching through a Chapter or Track
SZXCVB
During play, press the SEARCH (
) buttons on the remote control.
HDD/DVD-VIDEO/
DVD-RAM/-RW/-R
X2X4X8
 X 16  X 32  X 128
DivX
X2X4X8
AUDIO CD
(CD-DA)
X2X4X8
• You can scan the programme in reverse.
) buttons, playback is
• When you press and hold the SEARCH (
done at the default speed of X 4.
) buttons , playback is performed
If you release the SEARCH (
at a normal speed.
• To return to normal speed playback, press the PLAY (
) button.
CDs(CD-DA).
(You can hear sound during forward search(X 2) in disc.)
 The speed marked in this function may be different from the
Playback
M  No sound is heard during Scan(Search) mode, except with
actual playback speed.
Skipping Chapters, Titles or Markers
SXCVB
During play, press the SKIP (
) buttons on the remote control.
• If you press the SKIP ( ) button,
it moves to the beginning of the chapter or Title or marker
(HDD/DVD-RAM/-RW(VR mode)).
Pressing the button once again within 3 seconds returns to the
beginning of the previous chapter or Title or marker
(HDD/DVD-RAM/-RW(VR mode)).
• If you press the SKIP ( ) button,
it moves to the next chapter or track or marker
(HDD/DVD-RAM/-RW(VR mode)).
English - 39
01392A_HR750_XEU-ENG-0423.indd 39
2007-04-24
9:32:11
Slow Motion Play
SZXCVD
In pause mode, press the SEARCH (
control.
) buttons on the remote
• If you press the SEARCH (
 1/2  1/4  1/8
) button,
• If you press the SEARCH (
 1/2  1/4  1/8
) button,
• To return to normal speed playback, press the PLAY (
) button.
) buttons during pause, the disc
Press and hold the SEARCH (
will play slowly at 1/4 speed. If the button is released, the pause
operation will resume.
M  The speed marked in this function may be different from the
actual playback speed.
 Slow motion operates only in the forward direction on DivX
discs.
Playback
Step Motion Play
SZXCVD
Press the SKIP(
mode.
,
) buttons on the remote control in the pause
• Each time the button is pressed, a new frame will appear.
When the SKIP( ) button is pressed, the previous frame will be
activated.
When the SKIP( ) button is pressed, the next frame will be
activated.
• To return to normal speed playback, press the PLAY (
) button.
M  Step motion operates only in the forward direction on DivX
discs.
English - 40
01392A_HR750_XEU-ENG-0423.indd 40
2007-04-24
9:32:12
Using the INFO button
The INFO function allows you to easily search for a desired scene
by accessing title, chapter, time.
You can also change the subtitle and audio settings and set some
features including Angle, Repeat, Zoom.
Moving to a scene directly using the INFO
HDD
t Search
O Subtitle
Q Audio
P Repeat
v Zoom
>MOVE
Info
|
None
2 D 2/0 L+R
Off
Off
sSELECT
|
SZXCVD
If you want to move to a certain title, chapter or time, use this
function.
1. Press the INFO button during playback.
Search
w Title
x Time
<CHANGE
2. Press the ▲▼ buttons to select Search, then press the OK button
or ► button.
Info
1/3
00:00:37
sSELECT
3. Press the ▲▼ buttons to select Title, Chapter or Time.
4. Press the ◄► buttons or number buttons to select the desired
scene, then press the OK button.
In case of searching a time, enter the time in the sequence of hours,
minutes, and seconds using the number buttons.
Then press the OK button.
When an audio CD(CD-DA) or an MP3/JPEG disc is inserted,
depending on the disc type, the information display may not
appear.
 The Time Search function does not operate in some discs.
Playback
M  This may not work for some discs.
 To make the screen disappear, press the RETURN button.
Selecting the Subtitle Language
DVD-VIDEO
t Search
O Subtitle
Q Audio
z Angle
P Repeat
v Zoom
>MOVE
Info
|
Off
ENG 2 D 5.1 CH
1/1
Off
Off
<CHANGE
|
ZD
Selects one of the subtitle language recorded on the disc.
You can also operate this function by pressing the SUBTITLE
button on the remote control.
1. Press the INFO button during playback.
2. Press the ▲▼ buttons to select Subtitle.
3. Press the ◄► buttons to select the desired subtitle language.
M  The subtitle display may be different depending on the disc
type.
 Some discs allow you to select the language for the disc menu
only.
English - 41
01392A_HR750_XEU-ENG-0423.indd 41
2007-04-24
9:32:14
Selecting the Soundtracks & Audio Channels
HDD
t Search
O Subtitle
Q Audio
P Repeat
v Zoom
>MOVE
Info
|
None
2 D 2/0 L+R
Off
Off
<CHANGE
SZXCD
|
Selects one of the soundtracks recorded on the disc. Also selects
the audio channels from recorded TV programmes.
You can also operate this function by pressing the AUDIO button
on the remote control.
1. Press the INFO button during playback.
2. Press the ▲▼ buttons to select Audio.
3. Press the ◄► buttons to select the desired soundtracks or audio
channel.
M  Soundtracks or Audio channel may be different because they
are disc-specific.
 Some discs allow you to select the audio language for the disc
menu only.
Playback
Changing the Camera Angle
DVD-VIDEO
t Search
O Subtitle
Q Audio
z Angle
P Repeat
v Zoom
>MOVE
Info
|
ENG
ENG 2 D 5.1 CH
1/4
Off
Off
<CHANGE
|
Z
When a DVD VIDEO contains multiple angles of a particular
scene, you can select the Angle function.
1. Press the INFO button during playback.
2. Press the ▲▼ buttons to select Angle.
3. Press the ◄► buttons to select the desired angle.
M  This function is disc-dependent, and may not work on all
DVDs.
 This function does not work when a DVD has not been
recorded with a multi-camera angle system.
 Displays the current angle, total angle number.
English - 42
01392A_HR750_XEU-ENG-0423.indd 42
2007-04-24
9:32:15
Repeat Play
Playing Repeatedly (Repeat Playback)
HDD
t Search
O Subtitle
Q Audio
P Repeat
v Zoom
<CHANGE
SZXCVD
Info
|
None
2 D 2/0 L+R
Off
Off
sSELECT
|
You can also operate this function by pressing the REPEAT
button on the remote control.
1. Press the INFO button during playback.
2. Press the ▲▼ buttons to select the Repeat.
3. Press the ◄► buttons to select Off, A-B or Title or Chapter you
want to play repeatedly, then press the OK button.
M  HDD/DVD-RAM/-RW(VR mode), unfinalised DVD-R and
unfinalised DVD-RW (V mode) discs will do not repeat a
chapter.
 You can also activate Normal Playback by pressing the
EXIT(
) button.
Repeat A-B
Info
|
None
2 D 2/0 L+R
A-B
Off
sSELECT
|
SZXCV
You can also operate this function by pressing the REPEAT A-B
button on the remote control.
Playback
HDD
t Search
O Subtitle
Q Audio
P Repeat
v Zoom
<CHANGE
1. Press the INFO button during playback.
P Repeat A-B
A-B
2. Press the ▲▼ buttons to select Repeat.
3. Press the ◄► buttons to select A-B, then press the OK button.
sSELECT
4. Press the OK button at the point where you want the repeat play to
start (A) and press it again at the point where you want the repeat
play to stop (B). Repeat playback of the A-B section starts.
M  If you set point (B) before five seconds of playback has lapsed,
the prohibition mark ( ) will appear.
 You can also activate Normal Playback by pressing the
EXIT(
) button.
 Audio CDs(CD-DA), MP3 discs and DivX discs do not support
the Repeat A-B function.
English - 43
01392A_HR750_XEU-ENG-0423.indd 43
2007-04-24
9:32:15
Zooming-In
HDD
t Search
O Subtitle
Q Audio
P Repeat
v Zoom
<CHANGE
Info
|
None
2 D 2/0 L+R
Off
Off
sSELECT
SZXCV
|
1. Press the INFO button during playback.
2. Press the ▲▼ buttons to select Zoom, then press the OK or ►
button. ( ) will be displayed.
3. Press ▲▼◄► buttons to move to the area you want to enlarge.
4. Press the OK button.
The screen will be enlarged to twice the normal size. The screen
size will be enlarged to four times the normal size.
HDD/DVD-VIDEO/
DVD-RAM/-RW/-R
normal size ➞ X2 ➞ X4
➞ X2 ➞ normal size
M  When the recording is done in EP mode, the zoom function is
Playback
not supported except when the recording has been in V mode.
English - 44
01392A_HR750_XEU-ENG-0423.indd 44
2007-04-24
9:32:18
W Marker
01 02 -- -- -- -- -- -- -- --
N:2
Using Markers
SXC
(VR mode)
<MOVE
sPLAY
Cancel
rRETURN
Set marks at scenes you want to see again so that you can start
playback from the marked position.
Setting Markers
1. Press the MARKER button during playback.
2. Press the OK button when the desired scene appears.
• The number 01 is displayed and the scene is memorized.
3. Press the ► buttons to move to the next position.
4. Press the OK button again when the desired scene appears.
• The number 02 is displayed and the scene is memorized.
• HDD, DVD-RAM or DVD-RW (VR Mode) discs have the Marker
function instead of the Bookmark function. Since the scenes may
be displayed as many different pages, numbering is necessary.
If a disc in use is encoded with Disc Protection, Markers cannot
be set or deleted, only playback is available.
Playback
Playing back a marker
1. Press the MARKER button during playback.
2. Press the ◄► buttons to select a marked scene.
3. Press the OK or PLAY (
scene.
) button to start playing from the selected
• If you press the SKIP ( ) button, it moves to the beginning of the
marker. Pressing the button once again within 3 seconds returns
to the beginning of the previous marker.
• If you press the SKIP (
) button, it moves to the next marker.
Clearing a marker
1. Press the MARKER button during playback.
2. Press the ◄► buttons to select a marked scene.
3. Press the RED(A) button to delete the selected mark.
• When a marker is cleared while HDD/DVD-RAM/-RW (VR mode)
is playing, marker numbers will change. For example, if the 7th
marker is cleared after ten markers are registered, the marker
numbers after the eighth will automatically move ahead by one
and the 8th marker becomes the 7th.
English - 45
01392A_HR750_XEU-ENG-0423.indd 45
2007-04-24
9:32:19
W Bookmark
Using the Bookmarks
1 2 - - - - - - - --
ZCV
(V mode)
<MOVE
sPLAY
Cancel
rRETURN
Setting Bookmarks
1. Press the MARKER button during playback.
2. Press the OK button when the desired scene appears.
• The number 1 is displayed and the scene is memorized.
3. Press the ► buttons to move to the next position.
4. Press the OK button again when the desired scene appears.
The number 2 is displayed and the scene is memorized.
• Repeat above to bookmark other positions.
• You can bookmark up to 10 scenes.
M  When the disc tray is opened and then closed, bookmarks will
disappear.
Playback
Playing back a bookmark
1. Press the MARKER button during playback.
2. Press the ◄► buttons to select a bookmarked scene.
3. Press the OK or PLAY(
scene.
) button to start playing from the selected
Clearing a bookmark
1. Press the MARKER button during playback.
2. Press the ◄► buttons to select a bookmarked scene.
3. Press the RED(A) button to delete the selected bookmark.
English - 46
01392A_HR750_XEU-ENG-0423.indd 46
2007-04-24
9:32:21
Playing an Audio CD/MP3
Buttons on the Remote Control used for Audio
CD(CD-DA)/MP3 playback
4
3
5
6
5
2,7
1. ▲▼ : Selects a track (song).
2. OK button, Play (
) button: Plays the selected track (song).
3. SKIP (
) button: Moves to the next page.
4. SKIP (
) button: Moves to the previous page.
5. Press the SEARCH (
(Audio CD only)
1
2
) buttons: Fast Play (X 2, X 4, X 8)
6. STOP (
) button: Stops a track(song).
7. PLAY (
) button: Plays a track(song) or pauses playback.
8. RED(A) button: • Creates a playlist or go to playlist.
• Select Copy and Select All button.(MP3 disc only)
9
8
10
11
9. GREEN(B) button: Selects the sort order. (MP3 disc only)
10. YELLOW(C) button: Selects the play mode. (REPEAT)
11. BLUE(D) button: Selects a contents. (MP3 disc only)
Playback
Playing an Audio CD(CD-DA)
1. Insert an audio CD (CD-DA) into the disc tray.
• The audio CD menu appears and the tracks (songs) are played
automatically.
2. Press the ▲▼ buttons to select the track (song) you want to hear,
and then press the OK button.
➀
◆ Audio CD(CD-DA) Screen Elements
CD
Q TRACK01
➁
No.
Q
Title
TRACK01
Length
4:19
002
TRACK02
3:57
003
TRACK03
3:57
  ►   00:02:22
004
TRACK04
4:03
I TRACK01
005
TRACK05
4:09
006
TRACK06
5:08
007
TRACK07
3:31
➂
➃
Music List
1/10
Edit
#/$ PREVIOUS/NEXT PAGE
Play Mode
eEXIT
➄
➅
1. Current track (song): Displays the number of the track currently
being played.
2. Displays available buttons and a playback time corresponding to a
portion that is currently played.
3. Displays the current file type and file name.
4. Display available buttons.
5. Displays the current play index, total track number.
6. Displays the track list (song list).
English - 47
01392A_HR750_XEU-ENG-0423.indd 47
2007-04-24
9:32:22
Playing an MP3 Disc
1. Insert an MP3 disc into the disc tray.
• The menu is displayed
2. Press the ▲▼ buttons to select Library, then press the OK or ►
button.
3. Press the ▲▼ buttons to select Music, then press the OK or ►
button.
4. Press the ▲▼ buttons to select the track you want to hear, and then
press the OK button.
➀
CD
Q Song 1.mp3
Music List
1/9
No.
Title
Size
Y ROOT
➁
➂
➃
►
00:02:22
9 Song 1.mp3
E ROOT
Edit
Q Song 1.mp3
3.8 MB
002 Song 2.mp3
3.8 MB
003 Song 3.mp3
5.1 MB
004 Song 4.mp3
9.2 MB
005 Song 5.mp3
5.2 MB
006 Song 6.mp3
10.3 MB
Sort
Play Mode
#/$ PREVIOUS/NEXT PAGE
a CHECK
Contents
➄
➅
◆ MP3 Screen Elements
1. Current track (song): Displays the name of the track being played.
2. Displays available buttons and a playback time corresponding to a
portion that is currently played.
3. Displays the current file type, file name and folder name.
eEXIT
4. Displays available buttons.
5. Displays the current play index, total track number.
Playback
6. Displays the track list (song list).
CD
Q TRACK01
Music List
1/10
No.
Q
Title
TRACK01
002
TRACK02
3:57
003
TRACK03
3:57
  ►   00:02:22
004
TRACK04
Normal
4:03
I TRACK01
005
TRACK05
Repeat
4:09
006
TRACK06
Repeat
5:08
007
Track
All
TRACK07
Random
Edit
#/$ PREVIOUS/NEXT PAGE
Length
4:19
3:31
Play Mode
eEXIT
Repeat CD (CD-DA) & MP3
You can also operate this function by pressing the REPEAT
button on the remote control. During playback, press the REPEAT
button repeatedly to select the repeat mode you want.
1. Press the YELLOW(C) button during the Music List playback.
2. Press the ▲▼ buttons to select desired play mode, then press the
OK or ► button.
• Normal (CD (CD-DA)/MP3): Tracks on a disc are played in the
order in which they were recorded on the disc.
•
Repeat Track (CD (CD-DA)/MP3)
•
Repeat Folder (MP3)
•
Repeat All (CD (CD-DA)/MP3)
•
Random (CD (CD-DA)/MP3): The random option plays a
disc’s tracks in random order.
English - 48
01392A_HR750_XEU-ENG-0423.indd 48
2007-04-24
9:32:24
New Playlist
CD
Q TRACK01
Music List
1/10
No.
Q
Title
TRACK01
002
TRACK02
Length
4:19
3:57
003
TRACK03
3:57
  ►   00:02:22
004
TRACK04
4:03
I TRACK01
005
TRACK05
4:09
006
TRACK06
5:08
007
TRACK07
3:31
New Playlist
Go To Playlist
Edit
Play Mode
#/$ PREVIOUS/NEXT PAGE
eEXIT
CD
No.
Make Playlist
Title
No.
001 TRACK10
002 TRACK02
002 TRACK08
003 TRACK03
003 TRACK04
004 TRACK04
004 TRACK07
006 TRACK06
007 TRACK07
Save
2. Press the ▲▼ buttons to select New Playlist, then press the OK or
► button.
3. Press the ▲▼ buttons to select tracks in the order in which you
want them to play, then press the OK button.
4. To store the Playlist, press the RED(A) button.
A new Playlist will be created.
005 TRACK05
mMOVE
1. Press the RED(A) button during the Music List playback.
• If you playlisted a wrong track, press the ►▲▼ buttons to select
the wrong track, then press the OK button.
Playlist
001 TRACK01
You can register a maximum 30 tracks in the playlist.
Music List
sADD
rRETURN
eEXIT
CD
Playlist
q
U
No.
Title
Length
Y PLAYLIST
E PLAYLIST01
  ►   00:00:00
Y PLAYLIST
mMOVE
sSELECT
a CHECK
eEXIT
Playback
Go To Playlist
CD
Q TRACK01
Music List
1/10
No.
Q
Title
TRACK01
002
TRACK02
3:57
003
TRACK03
3:57
  ►   00:02:22
004
TRACK04
4:03
I TRACK01
005
TRACK05
4:09
006
TRACK06
5:08
007
TRACK07
3:31
New Playlist
Go To Playlist
Edit
Length
4:19
Play Mode
#/$ PREVIOUS/NEXT PAGE
eEXIT
CD
Playlist
q
1. Press the RED(A) button during the Music List playback.
2. Press the ▲▼ buttons to select Go To Playlist, then press the OK
or ► button.
3. Press the ▲▼ buttons to select the desired playlist folder, then
press the OK button.
The selected tracks are played automatically.
U
No.
Title
Length
Y PLAYLIST
E PLAYLIST01
  ►   00:02:22
Y PLAYLIST
mMOVE
sSELECT
a CHECK
eEXIT
English - 49
01392A_HR750_XEU-ENG-0423.indd 49
2007-04-24
9:32:27
Delete the Playlist
CD
Q TRACK01
Music List
1/10
No.
Q
Title
TRACK01
002
TRACK02
Length
4:19
3:57
003
TRACK03
3:57
  ►   00:02:22
004
TRACK04
4:03
I TRACK01
005
TRACK05
4:09
006
TRACK06
5:08
007
TRACK07
3:31
New Playlist
Go To Playlist
Edit
Play Mode
#/$ PREVIOUS/NEXT PAGE
eEXIT
1. Press the RED(A) button during the Music List playback.
2. Press the ▲▼ buttons to select Go To Playlist, then press the OK
or ► button.
3. Press the ▲▼ buttons to select the Playlist you want to delete.
4. Press the RED(A) button.
CD
q
Playlist
1/2
U
No.
Title
Length
Y PLAYLIST
E PLAYLIST01
5. Press the ◄► buttons to select Yes, then press the OK button.
The selected Playlist is deleted.
E PLAYLIST02
  ►   00:00:00
i PLAYLIST01
Delete
mMOVE
Edit Playlist
sSELECT
New Playlist
Music List
a CHECK
eEXIT
CD
q
Playlist
1/2
U
No.
Title
Y
Length
PLAYLIST
E to
PLAYLIST01
Do you want
delete?
E PLAYLIST02
  ►   00:00:00
l PLAYLIST01
Delete
<MOVE
Yes
No
Edit Playlist
sSELECT
New Playlist
Music List
a CHECK
eEXIT
Playback
CD
Q TRACK01
Music List
1/10
No.
Q
Title
TRACK01
002
TRACK02
3:57
003
TRACK03
3:57
  ►   00:02:22
004
TRACK04
4:03
I TRACK01
005
TRACK05
4:09
006
TRACK06
5:08
007
TRACK07
3:31
New Playlist
Go To Playlist
Edit
Play Mode
#/$ PREVIOUS/NEXT PAGE
eEXIT
CD
q
Playlist
1/2
U
No.
Title
Length
Y PLAYLIST
E PLAYLIST01
E PLAYLIST02
  ►   00:00:00
i PLAYLIST01
Delete
mMOVE
Edit Playlist
sSELECT
New Playlist
Music List
a CHECK
eEXIT
CD
No.
Edit Playlist
Title
Go To Edit Playlist
Length
4:19
No.
1. Press the RED(A) button during the Music List playback.
2. Press the ▲▼ buttons to select Go To Playlist, then press the OK
or ► button.
3. Press the ▲▼ buttons to select the Playlist you want to edit.
4. Press the GREEN(B) button in playlist mode.
5. Press the ▲▼ buttons to select tracks in the order in which you
want them to play, then press the OK button.
• If you playlisted a wrong track, press the ►▲▼ buttons to select
the wrong track, then press the OK button.
6. To store the Playlist, press the RED(A) button.
Playlist will be edited.
Playlist
001 TRACK01
001 TRACK10
002 TRACK02
002 TRACK04
003 TRACK03
003 TRACK06
004 TRACK04
004 TRACK07
005 TRACK05
006 TRACK06
007 TRACK07
Save
mMOVE
Music List
sADD
rRETURN
CD
Q TRACK04
eEXIT
U
No.
Title
Y
Playlist
1/4
Go To Music List
Length
PLAYLIST01
R
TRACK04
4:03
002
TRACK02
3:57
  ►   00:02:22
003
TRACK06
5:08
I TRACK04
k PLAYLIST01
004
TRACK01
4:19
Edit Playlist
New Playlist
1. Press the BLUE(D) button during the Playlist playback.
The Music List will be displayed.
Music List
eEXIT
English - 50
01392A_HR750_XEU-ENG-0423.indd 50
2007-04-24
9:32:30
Using the Sort
CD
Q Song 10.mp3
Music List
1/10
No.
Title
Size
Y ROOT
Q Song 10.mp3
►
00:02:22
9 Song 10.mp3
E ROOT
Name
002 Song 1.mp3
5.8MB
003 Song 2.mp3
5.1MB
004 Song 3.mp3
Size
Edit
3.8MB
9.2MB
005 Song 4.mp3
5.2MB
006 Song 5.mp3
10.3MB
Sort
Play Mode
#/$ PREVIOUS/NEXT PAGE
Contents
a CHECK
eEXIT
When you need to change the Sort order of Music List, you can
change it simply.
1. While the list menu is displayed, press the GREEN(B) button to
select Sort.
2. Press the ▲▼ buttons to select the desired item, then press the OK
or ► button.
• Name : In alphabetical order
• Size : In order of audio file size.
M  Audio CD(CD-DA) is not available.
 You can sort by Name, Length. Sorted list will be resorted in
copied order upon reentering Music List.
CD
Q Song 10.mp3
Music List
1/10
No.
Title
Size
Y ROOT
Q Song 10.mp3
►
00:02:22
9 Song 10.mp3
E ROOT
5.8MB
003 Song 2.mp3
Title 5.1MB
DivX 9.2MB
Music5.2MB
Photo10.3MB
005 Song 4.mp3
006 Song 5.mp3
Edit
3.8MB
002 Song 1.mp3
004 Song 3.mp3
Sort
Play Mode
a CHECK
1. Press the BLUE(D) button to select Contents.
2. Press the ▲▼ buttons to select the contents you want to move, then
Press the OK or ► button.
Contents
eEXIT
Playback
#/$ PREVIOUS/NEXT PAGE
Select Contents
M  This function is possible only when the disc contains the
selected contents.
 Audio CD(CD-DA) is not available.
English - 51
01392A_HR750_XEU-ENG-0423.indd 51
2007-04-24
9:32:36
CD
Image 1.jpg
Photo List
1/17
ROOT
Image 1.jpg
Image 10.jpg
Image 11.jpg
Image 13.jpg
Image 14.jpg
Image 15.jpg
Image 16.jpg
Edit
Sort
#/$ PREVIOUS/NEXT PAGE
Slideshow
a CHECK
Contents
eEXIT
Viewing a Picture
G
1. Insert a JPEG disc into the disc tray.
• The menu is displayed
2. Press the ▲▼ buttons to select Library, then press the OK or ►
button.
3. Press the ▲▼ buttons to select Photo, then press the OK or ►
button.
• To see the next 8 pictures, press the SKIP (
) button.
• To see the previous 8 pictures, press the SKIP(
) button.
4. Press the ▲▼◄► buttons to select a desired picture, then press
the OK button.
Slide Show
Image 1.jpg
1/17
5. Press the PLAY (
)button.
• Once in the Photo List, you can also operate slideshow in by
pressing the YELLOW(C) button.
Rotate
Playback
>PHOTO
► SLIDE SHOW
Zoom
rRETURN
Image 1.jpg
eEXIT
1/17
6. Press the RED(A) button to select Speed.
7. Press the ▲▼ buttons to select the slideshow speed, then press the
OK or ► button.
The slideshow starts and plays at the selected speed.
• You can go to Photo List by pressing YELLOW(C) button.
Fast
Normal
Slow
Speed
>PHOTO
Slideshow Off
► SLIDE SHOW
Photo List
rRETURN
eEXIT
◆ To stop the Slide Show
Press the GREEN(B), STOP(
) or RETURN button.
Rotate
Image 1.jpg
1/17
To setup, follow steps 1 to 4 .
>PHOTO
5-1. Press the GREEN(B) button to select Rotate.
Off
Rotate 90
Rotate 180
Rotate 270
Rotate
Zoom
► SLIDE SHOW
rRETURN
eEXIT
6. Press the ▲▼ buttons to select the rotate angle, then press the OK
or ► button.
• Once you select a rotate angle, you can change it by pressing the
RED(A) button.
• You can go to Photo List by pressing YELLOW(C) button.
◆ To stop the Rotate
Rotate
Rotate Off
Photo List
rRETURN
eEXIT
Press the GREEN(B), STOP(
) or RETURN button.
English - 52
01392A_HR750_XEU-ENG-0423.indd 52
2007-04-24
9:32:40
Zoom
To setup, follow steps 1 to 4 in page 52.
5-1. Press the YELLOW(C) button to select Zoom.
6. Each time the OK button is pressed, the picture is enlarged up to
4x (four times the normal size).
➞ X2 ➞ X4 ➞ X2 ➞ Normal
• You can go to Photo List by pressing YELLOW(C) button.
◆ To stop the Zoom
Press the GREEN(B), STOP(
) or RETURN button.
Go To Photo List
To setup, follow steps 1 to 4 in page 52.
5-1. Press the RETURN button to go to Photo List.
Photo List
1/17
ROOT
Image 1.jpg
Image 10.jpg
Image 11.jpg
Image 13.jpg
Name
Image 14.jpg
Size
Image 15.jpg
Image 16.jpg
Edit
Sort
Slideshow
#/$ PREVIOUS/NEXT PAGE
Using the Sort
When you need to change the Sort order of Photo List, you can
change it simply.
1. While the list menu is displayed, press the GREEN(B) button to
select Sort.
Playback
CD
Image 1.jpg
Contents
a CHECK
eEXIT
2. Press the ▲▼ buttons to select the desired item, then press the OK
or ► button.
• Name : In alphabetical order
• Size : In order of photo file size.
M  You can sort by Name, Size. Sorted list will be resorted in
copied order upon reentering Photo List.
CD
Image 1.jpg
ROOT
Image 13.jpg
Edit
Photo List
1/17
Image 1.jpg
Image 14.jpg
Image 10.jpg
Image 11.jpg
Image 15.jpg
Title
DivX
Music
Image 16.jpg
Photo
Sort
#/$ PREVIOUS/NEXT PAGE
Slideshow
a CHECK
Contents
Select Contents
To setup, follow steps 1 to 3 in page 52.
1. Press the BLUE(D) button to select Contents.
2. Press the ▲▼ buttons to select the contents you want to move, then
Press the OK or ► button.
eEXIT
M  This function is possible only when the disc contains the
selected contents.
English - 53
01392A_HR750_XEU-ENG-0423.indd 53
2007-04-24
9:32:45
CD
Movie_01.avi
DivX List
1/1
No.
Title
Size
Y ROOT
001 Movie_01.avi
Playing a DivX
162.8MB
3 DivX
N Using the MENU button
E ROOT
1. Insert a DivX disc into the disc tray.
Edit
Sort
Subtitle Enc.
a CHECK
Contents
eEXIT
• The menu is displayed
2. Press the ▲▼ buttons to select Library, then press the OK or ►
button.
3. Press the ▲▼ buttons to select DivX, then press the OK or ►
button.
4. Press the ▲▼ buttons to select the avi file (DivX), then press the
OK or PLAY ( ) button.
5. When DivX file is played, you can use following functions. Pressing
the STOP ( ) button once during playback will display the file list,
pressing the button again will exit the menu screen.
DivX Function Description
Playback
Function
Description
Skip
) buttons,
During play, press the SKIP (
it moves forward or backward 5 minutes.
Search
) buttons
During play, press the SEARCH (
and press again to search at a faster speed.
(X 2, X 4, X 8)
Slow Motion Play
In pause mode(  Pause ), press the SEARCH (
button on the remote control. (1/2, 1/4, 1/8)
)
Reverse Slow Motion Play is not available.
Step Motion Play
In pause mode(  Pause ), press the SKIP ( )
button on the remote control in the still mode.
Reverse Step Motion Play is not available.
M  This unit can play the following video compression formats,
- DivX Video (Codec) Format : DivX 3.11 DivX 4.x DivX 5.x
(without QPEL and GMC)
- DivX Audio (Codec) Format : MP3, MPEG1 Audio Layer 2,
LPCM, AC3
 Supported subtitle file formats: .smi, .srt, .sub, .psb, .txt, .ass
(The subtitle file should have exactly the same name to
corresponding DivX file name)
 Some DivX files created on a personal computer may not be
play back. That is why Codec Type, Version and Higher
resolution over specification are not supported.
 You cannot play back the disc that is larger than a 720 x 576
pixel resolution.
English - 54
01392A_HR750_XEU-ENG-0423.indd 54
2007-04-24
9:32:49
DivX Subtitle Encoding
CD
Movie_01.avi
DivX List
1/1
No.
Title
Size
Y ROOT
001 Movie_01.avi
3 DivX
162.8MB
2. Press the ▲▼ buttons to select a supported DivX subtitle language
by region, then press the OK button.
Western(Windows)
Central(Windows)
Greek(Windows)
Cyrillic(Windows)
E ROOT
Edit
Sort
1. Press the YELLOW(C) button in the file list.
Subtitle Enc.
Contents
a CHECK
eEXIT
Western
Afrikaans, Basque, Catalan, Danish, Dutch, English,
Faeroese, Finnish, French, German, Icelandic,
Indonesian, Italian, Malay, Norwegian, Portuguese,
Spanish, Swahili, Swedish
Central
English, Albanian, Croatian, Czech, Hungarian, Polish,
Romanian, Serbian(Latin), Slovak, Slovenian
Greek
English, Greek
Cyrillic
English, Azeri, Belarusian, Bulgarian, Kazakh,
Macedonian, Russian, Serbian, Tatar, Ukrainian,
Uzbek
M  If the subtitle language is displayed in broken fonts, change
DivX Subtitle to the appropriate region. If is still does not work,
the format is not supported.
DivX List
1/3
No.
Title
Size
Y ROOT
3 DivX
001 Movie_01.avi
162.8MB
002 Movie_02.avi
238.2MB
003 Movie_03.avi
118.4MB
Using the Sort
When you need to change the Sort order of DivX List, you can
change it simply.
E ROOT
Name
Size
Edit
Sort
Subtitle Enc.
Contents
a CHECK
eEXIT
Playback
CD
Movie_01.avi
1. While the list menu is displayed, press the GREEN(B) button to
select Sort.
2. Press the ▲▼ buttons to select the desired item, then press the OK
or ► button.
• Name : In alphabetical order
• Size : In order of DivX file size.
M  You can sort by Name, Size. Sorted list will be resorted in
copied order upon reentering DivX List.
Select Contents
CD
Movie_01.avi
DivX List
1/1
No.
Title
Size
Y ROOT
001 Movie_01.avi
3 DivX
Sort
Subtitle Enc.
a CHECK
1. Press the BLUE(D) button to select Contents.
2. Press the ▲▼ buttons to select the contents you want to move, then
Press the OK or ► button.
Title
DivX
Music
Photo
E ROOT
Edit
162.8MB
Contents
eEXIT
M  This function is possible only when the disc contains the
selected contents.
English - 55
01392A_HR750_XEU-ENG-0423.indd 55
2007-04-24
9:32:52
Recording
This section shows various HDD & DVD Recording
methods.
This unit can record on various types of discs.
Before recording, read the following instructions
and select the disc type according to your
preference.
Compatibility between Samsung and
Other Company’s Recorder
Disc Types
Recording
format
DVD-RAM
VR Mode
Recording
Device
X
Recordable
Other Company
X
Recordable
Samsung
VR Mode
Other Company
• DVD-HR749 / 750
HDD
DVD-RAM
DVD-RW
DVD-RW
Samsung
DVD-R
V Mode
Other Company
Samsung
• DVD-RAMs and DVD-RWs are rewritable.
DVD-R
• DVD-Rs are non-rewritable.
Additional Recording
in Samsung Recorder
Samsung
Recordable Discs
This HDD & DVD RECORDER can record on the
following discs.
Finalising
V Mode
Other Company
finalised
Not recordable
not finalised Recordable
finalised
Not recordable
not finalised Recordable
finalised
Not recordable
not finalised Recordable
finalised
Not recordable
not finalised Not recordable
finalised
Not recordable
not finalised Recordable
finalised
Not recordable
not finalised Not recordable
M  Finalise
- This closes the DVD-RW/-R so no additional
recording can be done.
 Unfinalise
Recording
- This allows additional recording on a
DVD-RW disc originally recorded on the HDD
& DVD RECORDER.
- A DVD-RW disc that has been recorded by
DAO(Disc At Once) in a PC cannot be
unfinalised.
- A DVD-RW disc that has been recorded in
Video Mode of a different maker’s recorder
cannot be unfinalised.
- A DVD-R disc cannot be unfinalised.
English - 56
01392A_HR750_XEU-ENG-0423.indd 56
2007-04-24
9:32:54
Recording Formats
<DVD-RW>
Uninitialized Disc.
Do you want to initialize this disc?
DVD-VR
DVD-V
No
When you insert an unused disc, the following message appears.
Since available functions differ depending on the disc type, select
a disc that best fits your preferences.
DVD-RAM: Formatting will be started automatically.
DVD-RW: Use after initializing the disc.
If you want to change the VR or V mode, refer to Formatting
a Disc on page 93.
DVD-R: Formatting disc is unnecessary and only V Mode Recording is
supported.
DVD-RAM/-RW(VR mode)
• This mode allows multiple editing functions (such as deletion of the
whole title, partial deletion of a title, etc.).
• Various editing options using a created Playlist.
DVD-RW(V mode)/-R
• Chapters will be created automatically when you finalise recording on
DVD-RW/-R discs in V mode.
The chapter’s length (interval between chapters) varies according to
the recording mode.
• Simple editing (erasing titles/changing title name).
Recording
English - 57
01392A_HR750_XEU-ENG-0423.indd 57
2007-04-24
9:32:55
Recording Mode
Select one of four recording modes by pressing the REC MODE
button repeatedly while the unit is in Stop mode for the desired
recording time and picture quality. In general, picture quality
improves as the recording time decreases. In FR mode, the most
suitable record mode is adjusted automatically, according to
remaining time on the disc and length of the timer recording. This
function is selected only one mode in XP, SP, LP and EP modes
and you can use this mode for timer recording.
• DVD-HR749 / DVD-HR750
Recording Mode
Recording Times
HDD (160GB)
DVD-RAM/-RW/-R
XP
(high quality mode)
Approx. 41 hours
Approx. 1 hour
about 8.5 Mbps
SP
(standard quality mode)
Approx. 67 hours
Approx. 2 hours
about 4.5 Mbps
LP
(long recording mode)
Approx. 133 hours
Approx. 4 hours
about 2 Mbps
EP
(extended mode)
FR
(Flexible Recording)
Approx. 199 hours
Approx. 264 hours
Approx. 41 hours ~ 199 hours
Approx. 6 hours/
about 1.6 Mbps
Approx. 8 hours/
about 1.2 Mbps
Approx. 1~6 hours
M  Recording time may vary according to specific conditions.
 1GB = 1,000,000,000 bytes; actual formatted capacity may be
Recording
less as the internal firmware uses a portion of the memory.
 The dual layer DVD-Rs have approximately double the
capacity of single layer DVD-Rs. (See page 36)
English - 58
01392A_HR750_XEU-ENG-0423.indd 58
2007-04-24
9:32:55
Unrecordable pictures
You cannot record copy protected movie.
Video with copy protection cannot be recorded on this HDD &
DVD RECORDER.
When the HDD & DVD RECORDER receives a copy- guard signal
while recording, recording stops and the following message
appears on the screen.
Concerning Copy Control Signals
TV broadcasts that contain copy control signals may have one of the
following three signal types, Copy-Free, Copy-Once and Copy-Never.
If you want to record a copy-once type programme, use DVD-RW with
CPRM in VR Mode and DVD-RAM.
Signal type
Media
DVD-RW(Ver.1.1)
Copy-Free
Copy-Once
Copy-Never
O
–
–
O
O*
–
DVD-RW(Ver.1.1)
with CPRM
VR mode
V mode
O
–
DVD-R
O
–
DVD-RAM(Ver. 2.0)
O
O*
–
Once “Copy Once” has been recorded, recording cannot be done
anymore.
◆ Content Protection for Recordable Media (CPRM)
Recording
CPRM is a mechanism that ties a recording to the media on which it is
recorded. It is supported by some HDD & DVD RECORDERs, but not
by many DVD players. Each blank recordable DVD has a unique 64-bit
media ID etched in the BCA. When protected content is recorded onto
the disc, it can be encrypted with a 56-bit C2 (Cryptomeria) cipher
derived from the media ID.
During playback, the ID is read from the BCA and used to generate a
key to decrypt the contents of the disc. If the contents of the disc are
copied to other media, the ID will be absent or wrong and the data will
not be decryptable.
English - 59
01392A_HR750_XEU-ENG-0423.indd 59
2007-04-24
9:32:55
Recording immediately
SXCV
Before you start
1. Check that the disc has enough available space for the recording.
2. Press the HDD or DVD button.
If you select DVD, Press the OPEN/CLOSE button and place a
recordable disc on the disc tray.
Press the OPEN/CLOSE button to close the disc tray.
Wait until LOAD disappears from the front panel display.
6 Record Mode
SP(35:12) >
Recording the current TV programme you are watching
) or number buttons to select the current
1. Press the PROG (
programme you want to record.
2. Press the REC MODE button repeatedly, (or press the REC MODE
button and then press the ▲▼ buttons) to select the recording
speed(quality).
HDD
 Recording:
➞ SP ➞ LP ➞ EP ➞ XP
PR 1 [SP]
3. Press the REC button.
Information concerning the channel is displayed on the screen, then
recording begins.
Recording
Icon( ) is displayed on the front panel.
Recording from external equipment you are watching
1. Press the INPUT SEL. button to select the input source according
to the connection you made.
The front panel display changes in the following sequence:
➞ PR Number ➞ AV1 ➞ AV2 ➞ AV3 ➞ DV
If you connect a digital camcorder, press the INPUT SEL. button to
select DV. (See page 62)
2. Press the REC MODE button repeatedly, (or press the REC MODE
button, then press the ▲▼ buttons) to select the recording speed
(quality).
➞ SP ➞ LP ➞ EP ➞ XP
English - 60
01392A_HR750_XEU-ENG-0423.indd 60
2007-04-24
9:32:56
3. Press the REC button.
Information concerning the external input mode is displayed on the
screen, then recording begins. Icon( ) is displayed on the front
panel.
To pause recording
• Press the REC PAUSE button to pause a recording in progress.
• Press the REC PAUSE button again during pause to resume
recording.
• You can switch channels by pressing the PROG (
while recording pauses.
) buttons
To stop recording
Press the STOP (
progress.
) button to stop or finish a recording in
• When using DVD-RAM/-RW/-R discs, the message “Updating the
information of disc. Please wait for a moment” is displayed.
M  You can not change the recording mode while recording.
 Recording will stop automatically if there is no free space left
for recording.
 Up to 99 titles can be recorded onto a DVD-RAM/-RW/-R disc.
 Up to 999 titles can be registered on the HDD.
 HDD recording is available for up to 24 hours, and when
recording for 24 hours, 3 titles will be recorded with each being
8 hours in length.
 Recording will stop automatically if a copy protected image is
selected.
 DVD-RAM/-RW discs must be formatted before starting to
record. Most new discs are sold unformatted.
Recording
 Do not use DVD-R authoring discs with this unit.
English - 61
01392A_HR750_XEU-ENG-0423.indd 61
2007-04-24
9:32:57
6 Record Mode
Copying from a Camcorder
SP(35:12) >
SXCV
You may control the Camcorder using the IEEE1394 (DV) interface.
1. Connect the DV output jack of your camcorder to the DV input jack
on the front of your HDD & DVD RECORDER using a DV cable.
DV
2. Press the HDD or DVD button.
If you select DVD, press the OPEN/CLOSE button and place a
recordable disc on the disc tray. Press the OPEN/CLOSE button to
close the disc tray. Wait until LOAD disappears from the front panel
display.
The DV device is connected
<MOVE
rRETURN
3. Press the REC MODE button repeatedly to select the recording
speed(quality).
➞ SP ➞ LP ➞ EP ➞ XP
4. Press the INPUT SEL. button to select DV.
If the input is set to DV, a playback/record menu that enables
camcorder control appears on the top of the screen.
5. Select the Play (►) icon on the upper part of the screen to playback
the camcorder and find the starting position to copy.
6. To start recording, use the ◄► buttons to select Record ( ● ) icon
in the top side of the screen, then press the OK button.
You can press the REC button of the remote control to start
recording.
To stop recording
Recording
Press the STOP (
) button to stop or finish a recording in progress.
• When using DVD-RAM/-RW/-R discs, the message “Updating the
information of disc. Please wait for a moment” is displayed.
M  To display playback related icons on the screen, press any
direction button on the remote control.
English - 62
01392A_HR750_XEU-ENG-0423.indd 62
2007-04-24
9:32:58
Making a One Touch Recording (OTR)
HDD
 Recording:
SXCV
PR 1 [SP]
You can set the HDD & DVD RECORDER to record in 30-minute
increments up to 8 hours by pressing the REC button.
5 OTR Mode
0:30
1. Press the HDD or DVD button.
If you select DVD, press the OPEN/CLOSE button and place a
recordable disc on the disc tray. Press the OPEN/CLOSE button to
close the disc tray. Wait until LOAD disappears from the front panel
display.
2. Press the PROG (
) or number buttons to select the
programme to record. If you want to record through a connected
external component, press the INPUT SEL. button to select an
appropriate external input(AV1, AV2, AV3, DV or PR01).
3. Press the REC button to start recording.
4. Press the REC button repeatedly to adjust the desired recording
time.
➞ 0:30 ➞ 1:00 ➞ ... 8:00 ➞ Off
M  The timer counter decreases by the minute from 8:00 to 0:00,
then the HDD & DVD RECORDER stops recording.
To stop recording
Press the STOP ( ) button. The message “Do you want to stop
recording?” is displayed.
• Or press the STOP (
) button again.
Recording
• Press the ◄► buttons to select Yes, then press the OK button.
English - 63
01392A_HR750_XEU-ENG-0423.indd 63
2007-04-24
9:33:00
Simultaneous Recording and Playback
S
You can play back from the beginning of the programme you are
currently recording.
You can watch the previous title list while recording a
programme.
Using the PLAY (
) button
HDD
► Play
1. With the unit in recording mode, press the PLAY ( ) button.
It plays back the title that you are currently recording from the
beginning.
Playback is not available for 10 seconds from the start of recording.
) and other playback-related buttons
You can use the SKIP (
to view the previous recorded list.
Stopping Playback / Recording
1. Press the STOP ( ) button. Playback screen disappears and the
recording in progress screen appears.
2. Pressing the STOP (
HDD
RECORDING...
Title List
4/4
No.
Title
002 JAN/01/2007 21:00 PR 01:00:00
003 JAN/01/2007 23:15 PR 00:30:00
004 RECORDING...
00:00:00
4 JAN/02/2007 00:00
1 XP
Recording
eEXIT
HDD
► Play
N Using the TITLE LIST button
Length
001 JAN/01/2007 17:30 PR 01:00:00
3 MPEG2
) button once more will stop the recording.
1. With the unit in recording mode, press the TITLE LIST button.
The above operation is possible from approx.10 seconds or more
after recording starts.
Press the ▲▼/SKIP (
) buttons to select the recording title list.
2. Press the OK or PLAY ( ) button.
It plays back the title that you are currently recording from the
beginning.
N Using the MENU button
1. With the unit in recording mode, press the MENU button.
2. Press the ▲▼ buttons to select Title, then press the OK button.
Title List screen is displayed.
3. Press the ▲▼/SKIP (
) buttons to select the recording title list,
then press the OK or ► button.
It plays back the title that you are currently recording from the
beginning.
Stopping Playback / Recording
1. Press the STOP( ) button once, playback screen disappears and
the Title List screen appears.
2. Pressing the MENU(
screen appears.
) button again, the recording in progress
3. Pressing the STOP(
) button once more will stop the recording.
English - 64
01392A_HR750_XEU-ENG-0423.indd 64
2007-04-24
9:33:02
M  No sound is heard during search mode.
 DVD disc or HDD playback is available during HDD recording.
However, JPEG, MP3, and DivX files in the disc cannot be
played back.
 HDD playback is available during DVD recording. However,
JPEG and MP3 files in the HDD cannot be played back.
Time Shift function as a live signal
/ Time Shift
On
S
>CHANGE
This function replays recordings as a live signal.
If you are interrupted while watching a TV programme, simply
press the TIME SHIFT button, and the HDD & DVD RECORDER
immediately starts recording the programme.
sSELECT
1. Press the TIME SHIFT button on the remote control.
The Time Shift menu is displayed.
2. Press the ▲▼ button to select On, then press the OK button.
Using the Time Shift function
14:02:28

HDD
14:02:28
Pause
1. While watching the currently broadcasting programme, press the
PLAY/PAUSE ( ) button.
The programme on TV is set in pause mode and the Time Shift Bar
is displayed.
2. Press the PLAY/PAUSE (
programme.
►
HDD
14:02:28
►
➂➃ ➄
13:25:04
Play
➆
➅
14:02:28
◆ Time Shift Screen Elements
1.
2.
3.
4.
5.
6.
7.
Displays the current media.
Displays the current status.
Watching Point.
Current play time.
Live Point.
Live Time.
Time Shift Time Bar
Recording
➀ ➁
HDD
13:25:04
Play
) button again to resume watching the
Buttons on the Remote Control used for Time Shift function
1. PLAY/PAUSE (
2. SEARCH (
) button : Pause live TV and resumes playback.
) buttons : Fast play ( X 2, X 4, X 8, X 16, X 32, X 128)
3. SKIP (
) button, STOP (
4. SKIP (
) button : Returns to the point where Time Shift begines.
) button : Switches to live TV.
M  The Time Shift is available only when HDD mode is selected.
 You can use this function for up to maximum two hours.
 You can only play the contents by using the menu when the
Time Shift is set to On.
English - 65
01392A_HR750_XEU-ENG-0423.indd 65
2007-04-24
9:33:06
Making a Timer Recording
SXCV
1. Check the antenna cable is connected.
2. Check the remaining time of the disc.
3. Check the date and time are correct.
Make sure the Clock (Setup-Clock Set) must be set before you
proceed with a timer recording. (See page 25)
HDD & DVD RECORDER
HDD
Library Video Plus+
Timer Record
Timer Record
|
|
Scheduled List
Video Plus+ Extended
Disc Manager
|
: Off
|
Recorded List
Setup
N Using the TIMER button
1. With the unit in Stop mode/Playback mode, press the TIMER button.
2. Press the OK or ► button to select Scheduled List
3. Press the OK button to select Add a list.
mMOVE
sSELECT
rRETURN
HDD
No.
eEXIT
Scheduled List
Current Time 10:54
To Source
Date
Start
End
Add a list
Mode
PDC
4. Set timer recording option.
• Fill the input items using the ▲▼◄► buttons and number buttons.
◄► : Moves to the previous/next item.
▲▼, 0~9 : Sets a value.
• To : Select the media to record HDD or DVD.
• Source : The video input source (AV1, AV2 or AV3), or the
broadcasting channel you want to make a timer recording from.
Recordable Time HDD 108:14 SP
Recorded List
sSELECT
rRETURN
HDD
Scheduled List
Current Time 10:54
No. To Source
No. 01 No Title
To
eEXIT
Source
Date
Start
End
Add a list
Date
HDD PR 01 JAN 01
Mode
Start
End
10 : 54
12 : 54
PDC
Mode PDC
SP
Title
Recordable Time HDD 108:14 SP
On
s Save
Recordable Time HDD 108:14 SP
Recorded List
sSELECT
Recording
<MOVE
rRETURN
• Date : Timer Recording allows setting the recording time within
one month period. Set the recording day. (month/day)
eEXIT
JAN 31
Every SUN
JAN 30
JAN 29
Every SAT
MON-FRI
JAN 02
MON-SAT
JAN 01
Every Day
• Start/End Time : Start and end time of the timer recording.
• Mode (Recording Mode) :
- FR (Flexible Recording) : Select when you want to set video
quality automatically. In FR mode, the most suitable record
mode is adjusted automatically, according to remaining time on
the disc and length of the timer recording. This function is
selected only one mode in XP, SP, LP and EP modes.
- XP (high quality) : Select when video quality is important.
- SP (standard quality) : Select to record in standard quality.
- LP (low quality) : Select when a long recording time is required.
- EP (extended) : Select when a longer recording time is required.
- The dual layer DVD-Rs have approximately double the capacity
of single layer DVD-Rs. (See page 36)
English - 66
01392A_HR750_XEU-ENG-0423.indd 66
2007-04-24
9:33:09
M  When you are recording at EP mode on a DVD-RW(V mode)/R disc, it may not record the full 6 or 8 hours because the unit
uses the VBR(Variable Bit Rate) ENCODING system. For
example, if you record a programme with a lot of action,
it uses a higher bit rate which in turn consumes more disc
memory.
• PDC : PDC(Programme Delivery Control) function.
- If you set this function on, you can control the starting and
ending time of recording by special signal included in the
broadcasting signal. If a TV programme is shortened or starts
earlier or later than scheduled, this function synchronizes the
starting and ending time of recording with the actual
broadcasting time automatically.
- Set up the start-time EXACTLY according to the published TV
schedule. Otherwise the timer recording will not operate.
- Do not select PDC unless you are sure the programme you
wish to record is broadcast with PDC.
• TITLE : To label the title name, press the RED(A) button.
Title renaming screen appears.
Follow steps 4 and 5 of “Renaming (Labeling) a Title” on page 73.
5. After selecting the set up value for each mode, press the OK button
to select Save.
•
will appear on the front panel. It means that a timer recording
is registered.
If the timer settings overlap;
The programmes are recorded in order of priority. After recording of
the first programme is complete, the second programme starts
being recorded.
To return to the previous menu
Press the RETURN button if you don’t want to set a timer recording.
Recording
To exit without saving the current setting
Press the EXIT ( ) button.
6. When you want to recording on DVD-RAM/-RW/-R, you must insert
the disc.
7. Turn the power off to finish the Timer Recording setting.
Timer Recording will not work when the power is on.
M  The timer recording time may differ from the set time
depending on disc status and overall timer recording status (for
example, recording times overlapping, or when the previous
recording ends within 2 minutes before the start time of the
next recording.)
 You can make the Timer Recording up to 12 programmes.
 If HDD disk has no available recording space,
blinks. It
means that HDD disk has no space to record.
 If you have set the Timer Recording using PDC, the fan can
still operate and make a noise when the power is off.
English - 67
01392A_HR750_XEU-ENG-0423.indd 67
2007-04-24
9:33:10
Editing the Scheduled List
HDD & DVD RECORDER
HDD
Library Video Plus+
Timer Record
Timer Record
|
|
Scheduled List
Video Plus+ Extended
Disc Manager
|
: Off
|
Recorded List
Setup
mMOVE
sSELECT
rRETURN
HDD
eEXIT
Scheduled List
Current Time 10:54
No. To Source
---- ---01 HDD PR 01
02 HDD PR 01
03 HDD PR 01
Date
-- -JAN 01
JAN 01
JAN 01
Start
--:-17:30
21:00
23:15
End
--:-18:30
22:00
23:45
Mode
-SP
SP
SP
PDC
-On
On
On
Recordable Time HDD 108:14 SP
Add
Delete
>MOVE
Recorded List
sSELECT
rRETURN
Follow these directions to edit the Scheduled List.
N Using the TIMER button
1. With the unit in Stop mode/Playback mode, press the TIMER
button.
2. Press the OK or ► button to select Scheduled List
3. Press the ▲▼ buttons to select the number of the Scheduled List
you want to edit, then press the OK button.
• Edit the items you want to modify. See the “Making a Timer
Recording” section for more information on Timer Recording Input
items. (See pages 66~67)
eEXIT
4. Press the OK button to confirm the edited setting.
HDD
Scheduled List
Current Time 10:54
No. To Source
No. 01 No Title
To
Source
Date
Start
End
Add a list
Date
HDD PR 01 JAN 01
Mode
Start
End
17 : 30
18 : 30
PDC
5. Press the EXIT ( ) button after finishing the operation. The
Scheduled List screen will disappear.
Mode PDC
SP
Title
Recordable Time HDD 108:14 SP
On
s Save
Recordable Time HDD 108:14 SP
Add
Delete
<MOVE
sSELECT
Recorded List
rRETURN
HDD
eEXIT
Scheduled List
Current Time 10:54
No. To Source
---- ---01 HDD PR 01
02 HDD PR 01
03 HDD PR 01
Date
-- -JAN 01
JAN 01
JAN 01
Start
--:-17:30
21:00
23:15
End
--:-18:30
22:00
23:45
Mode
-SP
SP
SP
PDC
-On
On
On
Recordable Time HDD 108:14 SP
Add
Delete
Recording
>MOVE
Recorded List
sSELECT
rRETURN
HDD
Scheduled List
Current Time 10:54
No. To Source
No. 04 No Title
To
eEXIT
Source
Date
Start
End
Add a list
Date
HDD PR 01 JAN 01
Mode
Start
End
17 : 30
18 : 30
PDC
Mode PDC
SP
Title
Recordable Time HDD 108:14 SP
On
s Save
Recordable Time HDD 108:14 SP
Add
Delete
<MOVE
sSELECT
Recorded List
rRETURN
eEXIT
Adding a Scheduled List
Follow these directions to add an entry from the Scheduled List.
N Using the TIMER button
1. With the unit in Stop mode/Playback mode, press the TIMER
button.
2. Press the OK or ► button to select Scheduled List
3. Press the ▲▼ buttons to select the number of the Scheduled List,
then press the RED(A) button.
• Set the items you want to add. See the “Making a Timer
Recording” section for more information on Timer Recording Input
items.(See pages 66~67)
4. Press the OK button to confirm the added setting.
HDD
No.
01
02
03
04
Scheduled List
Current Time 10:54
To Source
HDD
HDD
HDD
HDD
PR 01
PR 01
PR 01
PR 01
Date
JAN 01
JAN 01
JAN 01
JAN 02
Start
Add a List
17:30
21:00
23:15
17:30
End
Mode
PDC
18:30
22:00
23:45
18:30
SP
SP
SP
SP
On
On
On
On
5. Press the EXIT ( ) button after finishing the operation.
The Scheduled List screen will disappear.
Recordable Time HDD 108:14 SP
Recorded List
>MOVE
sSELECT
rRETURN
eEXIT
English - 68
01392A_HR750_XEU-ENG-0423.indd 68
2007-04-24
9:33:11
Deleting a Scheduled List
HDD & DVD RECORDER
HDD
Library Video Plus+
Timer Record
Timer Record
|
Video Plus+ Extended
Disc Manager
|
: Off
|
Recorded List
Follow these directions to delete an entry from the Scheduled
List.
Setup
mMOVE
sSELECT
rRETURN
HDD
eEXIT
Scheduled List
Current Time 10:54
No. To Source
---- ---01 HDD PR 01
02 HDD PR 01
03 HDD PR 01
Date
-- -JAN 01
JAN 01
JAN 01
Start
--:-17:30
21:00
23:15
End
--:-18:30
22:00
23:45
Mode
-SP
SP
SP
PDC
-On
On
On
Recordable Time HDD 108:14 SP
Add
>MOVE
Delete
sSELECT
Recorded List
rRETURN
HDD
eEXIT
Scheduled List
Current Time 10:54
No. To Source
-- No.---01 ---01 HDD PR 01
02 HDD PR 01
03 HDD PR 01
SXCV
|
Scheduled List
Date
Start
End
-- ---:---:-JAN 01
17:30 18:30
JAN
21:00to delete?
22:00
Do 01
you want
JAN 01
23:15 23:45
Yes
Mode
-SP
SP
SP
PDC
-On
On
On
No
Delete
mMOVE
sSELECT
Recorded List
rRETURN
1. With the unit in Stop mode/Playback mode, press the TIMER
button.
2. Press the OK or ► button to select Scheduled List
3. Press the ▲▼ buttons to select the number of the Scheduled List
you want to delete, and then press the GREEN(B) button.
• You will be prompted with the delete confirm message such as
“Do you want to delete?”.
4. Press the ◄► buttons to select Yes, then press the OK button.
• The selected entry will be deleted from the list.
5. Press the EXIT ( ) button after finishing the operation. The
Scheduled List screen will disappear.
Recordable Time HDD 108:14 SP
Add
N Using the TIMER button
eEXIT
Recording
English - 69
01392A_HR750_XEU-ENG-0423.indd 69
2007-04-24
9:33:15
HDD & DVD RECORDER
HDD
Library Video Plus+
Timer Record
Timer Record
|
SXCV
|
Scheduled List
Video Plus+ Extended
Disc Manager
Using the Video Plus+ Feature
|
: Off
|
Recorded List
Setup
mMOVE
sSELECT
rRETURN
eEXIT
Video Plus+
HDD & DVD RECORDER
HDD
1. With the unit in Stop mode, press the MENU button.
Library
Timer Record
Enter Video Plus+ Code number. [0-9]
Disc Manager
Setup
0~9 NUMBER
(Press [OK] button: Make Code.)
sSELECT
rRETURN
HDD
eEXIT
Scheduled List
Current Time 10:54
No. To Source
No. 01 No Title
Date
Start
End
Add a list
To
Source
Date
Start
End
HDD
––
JAN 01
10 : 54
12 :54
Mode
Mode PDC
SP
Title
Recordable Time HDD 108:14 SP
On
s Save
Recorded List
sSELECT
rRETURN
2. Press the ▲▼ buttons to select Timer Record, then press the OK
or ► button.
3. Press the ▲▼ buttons to select Video Plus+, then press the OK or
► button.
• A message is displayed to allow you to enter the Video Plus+
code.
PDC
Recordable Time HDD 108:14 SP
<MOVE
Before presetting your HDD & DVD RECORDER.
• Switch on both the television and your HDD & DVD RECORDER.
• Check that the date and time are correct.
Up to twelve programmes can be preset
eEXIT
4. Press the number buttons to enter the code of the programme that
you want to record in your television magazine.
• If you want to correct the Video Plus+ code that you are entering:
- Press the ◄ button until the digit to be corrected is cleared.
- Enter the correct digit.
5. Press the OK button.
• The information concerning the programme is displayed.
• When using the Video Plus+ function for the first time with stored
stations, the programme number flashes. This one time, you must
enter the PR number manually by pressing the ▲▼ buttons.
6. Press the RED(A) button if you do not want to use the default title
name.
The rename screen is displayed.
Follow steps 4 and 5 of “Renaming (Labeling) a Title” on page 73.
Recording
7. If the programme and times are correct, press the OK button.
8. Turn the power off by pressing the STANDBY/ON button to activate
the timer recording setting.
• Refer to pages 69, 71 if you want to
- Check whether the timer Recording has set correctly or not.
- Cancel a preset recording.
M  The numbers next to each TV programme listing in the
magazines or newspapers are Video Plus+ code numbers,
which allow you to programme your HDD & DVD RECORDER.
instantly with the remote control. Enter the Video Plus+ code
for the programme you wish to record.
 Video Plus+ is a trademark of Gemstar Development
Corporation. The Video Plus+ system is manufactured under
licence from Gemstar Development Corporation.
English - 70
01392A_HR750_XEU-ENG-0423.indd 70
2007-04-24
9:33:17
HDD & DVD RECORDER
HDD
Library Video Plus+
Timer Record
Timer Record
|
|
Scheduled List
Video Plus+ Extended
Disc Manager
|
: Off
|
Recorded List
Setup
mMOVE
sSELECT
rRETURN
Video Plus+ Extended
To prevent delays or overruns the HDD & DVD RECORDER has a
function called Video Plus+ Extended allowing you to extended
the recording time by up to 60 minutes.
• Only use if PDC is not available or set to OFF.
eEXIT
1. With the unit in Stop mode, press the MENU button.
HDD & DVD RECORDER
HDD
Library Video Plus+
Timer Record
Disc Manager
Setup
mMOVE
Timer Record
|
|
Scheduled List
Off
Video Plus+ Extended
10
Recorded List
20
30
40
50
60
sSELECT
|
: 30
|
rRETURN
eEXIT
2. Press the ▲▼ buttons to select Timer Record,
then press the OK or ► button.
3. Press the ▲▼ buttons to select Video Plus+ Extended,
then press the OK or ► button.
4. Press the ▲▼ buttons to select the Video Plus+ Extended time,
then the press OK or ► button.
5. Press the EXIT (
) button to exit the menu.
Go To Recorded List
HDD & DVD RECORDER
HDD
Library Video Plus+
Timer Record
Timer Record
|
Video Plus+ Extended
Disc Manager
|
: Off
|
Recorded List
Setup
mMOVE
SXCV
|
Scheduled List
You can confirm the performance results of title lists that have
passed the reserved recording time.
sSELECT
rRETURN
HDD
eEXIT
N Using the TIMER button
Recorded List
No.
To Source
Date
Start
End
Mode
PDC
Status
01
HDD PR 01
JAN 01
17:30
18:30
SP
On
OK
02
HDD PR 01
JAN 01
21:00
22:00
SP
On
OK
03
HDD PR 01
JAN 01
23:15
23:45
SP
On
OK
1. With the unit in Stop mode/Playback mode, press the TIMER
button.
2. Press the ▲▼ button to select Recorded List,
then press the OK or ► button.
Delete All
Scheduled List
sSELECT
rRETURN
HDD
eEXIT
Recorded List
No.
To Source
Date
Start
End
Mode
PDC
Status
01
HDD PR 01
JAN 01
17:30
18:30
SP
On
OK
02
HDD PR 01
JAN 01
21:00
22:00
SP
On
OK
03
HDD PR 01Timer
JANrec
01
SP
On
was 23:15
finished23:45
successfully
OK
Delete All
sSELECT
Scheduled List
rRETURN
3. Press the EXIT ( ) button after finishing the operation.
The Recorded List screen will disappear.
Information about Recorded List
Informs whether the selected Recorded List performed a Timer
Recording successfully.
3-1. Press the ▲▼ buttons to select the number of the Recorded List,
then press the OK button.
OK
Delete
Recording
Delete
>MOVE
eEXIT
English - 71
01392A_HR750_XEU-ENG-0423.indd 71
2007-04-24
9:33:19
Delete Recorded List
HDD
No.
Recorded List
Date
Start
End
Mode
PDC
Status
01 No.
HDD 01
PR 01
JAN 01
17:30
18:30
SP
On
OK
02
HDD PR 01
To Source
JAN 01
21:00
22:00
SP
On
OK
03
HDD PR 01
JANDo
01
you 23:15
want to 23:45
delete?SP
On
OK
Yes
Delete
mMOVE
No
Delete All
sSELECT
3-1. Press the ▲▼ buttons to select the number of the Recorded List
you want to delete, and then press the RED(A) button.
4. Press the ◄► buttons to select Yes, then press the OK button.
Scheduled List
rRETURN
Deletes a Recorded List individually.
eEXIT
Clear Recorded List
HDD
Recorded List
No.
To Source
Date
Start
End
Mode
PDC
Status
01
HDD PR 01
JAN 01
17:30
18:30
SP
On
OK
02
HDD PR 01
JAN 01
21:00
22:00
SP
On
OK
03
HDD PR Do
01
01 to delete
23:15 a23:45
SP list??
On
youJANwant
recorded
Yes
Delete
mMOVE
OK
sSELECT
3-1. Press the GREEN(B) button.
4. Press the ◄► buttons to select Yes, then press the OK button.
No
Delete All
Clears all Recorded List at once.
Scheduled List
rRETURN
eEXIT
Go to Scheduled List
HDD
Recorded List
No.
To Source
Date
Start
End
Mode
PDC
Status
01
HDD PR 01
JAN 01
17:30
18:30
SP
On
OK
02
HDD PR 01
JAN 01
21:00
22:00
SP
On
OK
03
HDD PR 01
JAN 01
23:15
23:45
SP
On
OK
Delete
>MOVE
Delete All
sSELECT
Recording
3-1. Press the YELLOW(C) button.
Scheduled List
rRETURN
HDD
No.
Switches directly from the Recorded List to the Scheduled List.
eEXIT
Scheduled List
Current Time 10:54
To Source
Date
Start
End
Add a list
Mode
PDC
Recordable Time HDD 105:44 SP
Recorded List
sSELECT
rRETURN
eEXIT
English - 72
01392A_HR750_XEU-ENG-0423.indd 72
2007-04-24
9:33:22
Editing
This section introduces basic functions of editing and explains both edit functions for the recording on a
disc and edit functions for the entire disc.
Recording or editing might not be completed if an error, such as a sudden power failure occurs.
Please be aware that a material that has been damaged is unable to be retrieved to its original content.
Basic Editing (Title List)
HDD
JAN/01/2007 17:30 PR1
Title List
1/3
No.
Title
Playing the Title
SXCV
Length
001 JAN/01/2007 17:30 PR 01:00:00
002 JAN/02/2007 21:00 PR 01:00:00
003 JAN/03/2007 23:15 PR 00:30:00
3 MPEG2
Follow these instructions to play back a scene from the Title List.
4 JAN/01/2007 17:30
1 SP
V-Mode Compatibility
Edit
Sort
Go to
Contents
a CHECK
eEXIT
N Using the TITLE LIST button
1. With the unit in Stop mode/Playback mode, press the TITLE LIST
button.
2. Press the ▲▼ buttons to select an entry you want to play from Title
List, then press the OK or PLAY ( ) button.
The selected entry (title) will be played back.
3. To stop title play, press the STOP( ) button.
The screen returns to the Title List screen.
Renaming (Labeling) a Title
HDD
JAN/01/2007 17:30 PR1
Title List
1/3
No.
Title
002 JAN/02/2007 21:00 PR 01:00:00
003 JAN/03/2007 23:15 PR 00:30:00
3 MPEG2
Follow these instructions to rename a title list entry, i.e., to edit
the title of a recorded programme.
4 JAN/01/2007 17:30
1 SP
V-Mode Compatibility
Edit
Sort
HDD
JAN/01/2007 17:30 PR1
Delete
Copy
Rename
Protection
Partial
Delete
3 MPEG2
Split4 JAN/01/2007 17:30
New1Playlist
SP
V-Mode
Select
All Compatibility
Edit
Go to
Contents
a CHECK
eEXIT
Title List
1/3
No.
Title
Length
001 JAN/01/2007 17:30 PR 01:00:00
Editing
SXCV
Length
001 JAN/01/2007 17:30 PR 01:00:00
N Using the TITLE LIST button
1. With the unit in Stop mode/Playback mode, press the TITLE LIST
button.
002 JAN/02/2007 21:00 PR 01:00:00
003 JAN/03/2007 23:15 PR 00:30:00
Sort
Go to
Contents
a CHECK
eEXIT
2. Press the ▲▼ buttons to select an entry you want to rename from
the Title List, then press the RED(A) button.
3. Press the ▲▼ buttons to select Rename, then press the OK or ►
button.
The Rename screen is displayed.
English - 73
01392A_HR750_XEU-ENG-0423.indd 73
2007-04-24
9:33:24
HDD
Rename
4. Select the desired characters using the ▲▼◄► buttons, press the
OK button.
• Back Space (RED(A) button) : Deletes and moves the cursor
backwards by one position.
Sports(A1)
• Space (GREEN(B) button) : Enters a blank and moves the
cursor one forward (to the right).
Back Space
mMOVE
Space
Clear
sSELECT
rRETURN
Save
eEXIT
• Clear (YELLOW(C) button) : Deletes all the character inputs.
• Save (BLUE(D) button) : Registers the character inputs.
5. Press the BLUE(D) button to select Save.
The changed title name is displayed on the title item of the selected
entry.
HDD
JAN/01/2007 17:30 PR1
Title List
1/3
No.
Title
Locking (Protecting) a Title
SXCV
Length
001 JAN/01/2007 17:30 PR 01:00:00
002 JAN/02/2007 21:00 PR 01:00:00
003 JAN/03/2007 23:15 PR 00:30:00
3 MPEG2
4 JAN/01/2007 17:30
1 SP
V-Mode Compatibility
Edit
Sort
Go to
Contents
a CHECK
eEXIT
HDD
JAN/02/2007 21:00 PR1
Title List
2/3
No.
Title
Length
001 JAN/01/2007 17:30 PR 01:00:00
Delete
Copy
Protection
3 MPEG2
New4Playlist
JAN/02/2007 21:00
Select
SP
1 All
V-ModeAll
Compatibility
Unselect
Edit
002 JAN/02/2007 21:00 PR 01:00:00
003 JAN/03/2007 23:15 PR 00:30:00
Sort
HDD
JAN/02/2007 21:00 PR1
Protection
Go to
Contents
a CHECK
eEXIT
Title List
2/3
No.
Title
Length
001 JAN/01/2007 17:30 PR 01:00:00
2 items002
areJAN/02/2007
selected 21:00 PR 01:00:00
Set title Protection
mode:23:15 PR 00:30:00
003 JAN/03/2007
3 MPEG2
4 JAN/02/2007 21:00
On
Off
1 SP
V-Mode Compatibility
Edit
Sort
sSELECT
Editing
<MOVE
Go to
Contents
rRETURN
eEXIT
Follow these instructions to lock an entry to protect it from
accidental deletion.
N Using the TITLE LIST button
1. With the unit in Stop mode/Playback mode, press the TITLE LIST
button.
2. Press the ▲▼ buttons to select an entry you want to protect from
the Title List, then press the MARKER button until a checkmark
appears. Repeat this step to select an additional title you want to
protect.
• If you don’t want to protect a certain one of the checked entries,
simply select that entry and press the MARKER to deselect it until
a checkmark disappears.
3. Press the RED(A) button to select Edit.
Edit menu is displayed.
4. Press the ▲▼ buttons to select Protection, then press the OK or ►
button.
5. Press the ◄► buttons to select On, then press the OK button. The
key icon on the information window for the selected entry changes
to the locked status. (10)
6. If you want to cancel the Protection, select Off in step 5 and press
the OK button. The key icon changes to the unlocked status.
(0 1)
M  If you select “Select All” in the Edit menu, all title will be
checked.
English - 74
01392A_HR750_XEU-ENG-0423.indd 74
2007-04-24
9:33:27
Deleting a Title
HDD
JAN/01/2007 17:30 PR1
Title List
1/3
No.
Title
SXCV
Length
001 JAN/01/2007 17:30 PR 01:00:00
002 JAN/02/2007 21:00 PR 01:00:00
003 JAN/03/2007 23:15 PR 00:30:00
3 MPEG2
Follow these instructions to delete an entry from the Title List.
4 JAN/01/2007 17:30
1 SP
V-Mode Compatibility
Edit
Sort
Go to
Contents
a CHECK
eEXIT
HDD
JAN/02/2007 21:00 PR1
Title List
2/3
No.
Title
Length
001 JAN/01/2007 17:30 PR 01:00:00
Delete
Copy
Protection
3 MPEG2
JAN/02/2007 21:00
New4Playlist
1 SP
Select
All
V-ModeAll
Compatibility
Unselect
Edit
002 JAN/02/2007 21:00 PR 01:00:00
003 JAN/03/2007 23:15 PR 00:30:00
Sort
Go to
Contents
a CHECK
eEXIT
HDD
JAN/02/2007 21:00 PR1
Title List
2/3
No.
Title
Length
001 JAN/01/2007 17:30 PR 01:00:00
2 items are selected
002 JAN/02/2007 21:00 PR 01:00:00
Do you want
to delete?
003 may
JAN/03/2007
23:15 PR 00:30:00
(Related playlists
be deleted.)
3 MPEG2
4 JAN/02/2007 21:00
Yes
No
1 SP
V-Mode Compatibility
Edit
<MOVE
Sort
sSELECT
Go to
Contents
rRETURN
eEXIT
N Using the TITLE LIST button
1. With the unit in Stop mode/Playback mode, press the TITLE LIST
button.
2. Press the ▲▼ buttons to select an entry you want to delete in the
Title List, then press the MARKER button until a checkmark
appears. Repeat this step to select an additional title you want to
delete.
• If you don’t want to delete a certain one of the checked entries,
simply select that entry and press the MARKER to deselect it until
a checkmark disappears.
3. Press the RED(A) button to select Edit.
Edit menu is displayed.
4. Press the ▲▼ buttons to select Delete, then press the OK or ►
button.
• The message may be different depending on the type of disc.
You will be prompted with the confirmation message.
HDD, DVD-RAM(VR mode), DVD-RW(VR mode): If a Playlist is
present, the message “Do you want to delete? (Related playlists
may be deleted.)” is displayed.
DVD-RW(V mode)/-R: If a Playlist is not present, the message
“Do you want to delete?” is displayed.
5. Press the ◄► buttons to select Yes, then press the OK button.
M  You cannot delete a protected entry. If you want to delete a
protected entry, select “Off” in the Title Protection menu.
(See page 74)
 When the Disc Protection has been set to Protected, you
cannot delete titles.
(See page 91)
 Once an entry is deleted from the Title List it cannot be
recovered.
 Once DVD-RW/-R is finalised, it cannot be deleted.
the Title remains physically on the disc.
 If you select “Select All” in the Edit menu, all title will be
Editing
 With DVD-R, titles are only deleted from the menu, however,
checked.
English - 75
01392A_HR750_XEU-ENG-0423.indd 75
2007-04-24
9:33:31
Splitting a Section of a Title (Split)
HDD
JAN/01/2007 17:30 PR1
Title List
1/3
No.
Title
S
Length
001 JAN/01/2007 17:30 PR 01:00:00
002 JAN/02/2007 21:00 PR 01:00:00
003 JAN/03/2007 23:15 PR 00:30:00
3 MPEG2
Follow these instructions to split a section of a Title List entry into
two titles.
4 JAN/01/2007 17:30
1 SP
V-Mode Compatibility
Edit
Sort
HDD
JAN/01/2007 17:30 PR1
Delete
Copy
Rename
Protection
Partial
Delete
3 MPEG2
Split4 JAN/01/2007 17:30
New1Playlist
SP
V-Mode
Select
All Compatibility
Edit
Go to
Contents
a CHECK
eEXIT
N Using the TITLE LIST button
Title List
1/3
No.
Title
1. With the unit in Stop mode/Playback mode, press the TITLE LIST
button.
Length
001 JAN/01/2007 17:30 PR 01:00:00
002 JAN/02/2007 21:00 PR 01:00:00
2. Press the ▲▼ buttons to select an entry you want to Split from the
Title List, then press the RED(A) button.
The Edit menu is displayed.
003 JAN/03/2007 23:15 PR 00:30:00
Sort
Go to
Contents
a CHECK
eEXIT
HDD
JAN/01/2007 17:30 PR1
3. Press the ▲▼ buttons to select Split, then press the OK or ►
button.
Split
),
4. Using the playback-related buttons (PLAY ( ), SEARCH (
move to a point for splitting and press the OK button.
If it is not the point where you want to split, press the RETURN
button to cancel the selection. Using the playback-related buttons,
move to a point to split and press the OK button.
Title List No. 001
Split 1
Split 2
00:00:00
00:00:00
►
00:00:01
Select
Split
Return
& PLAY/PAUSE
<MOVE
  SCAN
sSELECT
rRETURN
➀ First split interval
eEXIT
HDD
JAN/01/2007 17:30 PR1
➁ Current playtime
Split
➂ Start time of the second split and its screen
Title List No. 001
➀
Select
Split 2
00:00:00
00:00:20
►
00:00:20
Split
Return
& PLAY/PAUSE
<MOVE
Split 1
➂
➁
  SCAN
sSELECT
rRETURN
eEXIT
HDD
JAN/01/2007 17:30 PR1
Split
5. Press the OK button to select Split.
6. Press the ◄► buttons to select Yes, then press the OK button.
The split title is divided into two, and the following titles will be
shifted down by one.
Title List No. 001
Split 1
Split 2
00:00:00
00:00:20

Select
Return
& PLAY/PAUSE
<MOVE
00:00:20
Split
  SCAN
sSELECT
rRETURN
eEXIT
HDD
JAN/01/2007 17:30 PR1
Split
Title List No. 001
Split 1
Split 2
00:00:00
00:30:55
This title cannot be recovered after spliting.
Do you want to split?
Yes
No
Editing

Select
& PLAY/PAUSE
<MOVE
00:30:55
Split
Return
  SCAN
sSELECT
rRETURN
eEXIT
English - 76
01392A_HR750_XEU-ENG-0423.indd 76
2007-04-24
9:33:34
Deleting a Section of a Title (Partial Delete)
HDD
JAN/01/2007 17:30 PR1
Title List
1/3
No.
Title
SXC
Length
001 JAN/01/2007 17:30 PR 01:00:00
002 JAN/02/2007 21:00 PR 01:00:00
003 JAN/03/2007 23:15 PR 00:30:00
(VR mode)
3 MPEG2
4 JAN/01/2007 17:30
Follow these instructions to delete a section of a Title List entry.
1 SP
V-Mode Compatibility
Edit
Sort
HDD
JAN/01/2007 17:30 PR1
Delete
Copy
Rename
Protection
Partial
Delete
3 MPEG2
Split4 JAN/01/2007 17:30
New1Playlist
SP
V-Mode
Select
All Compatibility
Edit
Go to
Contents
a CHECK
eEXIT
N Using the TITLE LIST button
Title List
1/3
No.
Title
1. With the unit in Stop mode/Playback mode, press the TITLE LIST
button.
Length
001 JAN/01/2007 17:30 PR 01:00:00
002 JAN/02/2007 21:00 PR 01:00:00
2. Press the ▲▼ buttons to select an entry you want to edit from the
Title List, then press the RED(A) button.
The Edit menu is displayed.
003 JAN/03/2007 23:15 PR 00:30:00
Sort
Go to
Contents
a CHECK
eEXIT
HDD
JAN/01/2007 17:30 PR1
3. Press the ▲▼ buttons to select Partial Delete, then press the OK
or ► button.
Partial Delete
4. Press the OK button at the starting point.
The image and starting point time is displayed in the section
deletion starting point window.
Title List No. 001
Start
End
00:19:10
00:41:20
►
Start
Delete
& PLAY/PAUSE
<MOVE
Partial Delete List Screen Elements
00:41:20
End
Return
➀ Playback bar
  SCAN
sSELECT
rRETURN
eEXIT
HDD
JAN/01/2007 17:30 PR1
➁ Playtime
➂ Section deletion starting point window and time
Partial Delete
➃ Section deletion end point window and time
Title List No. 001
➀
Start
End
00:19:10
00:41:20

Start
00:41:20
End
Delete
& PLAY/PAUSE
<MOVE
Return
  SCAN
sSELECT
rRETURN
eEXIT
➂
HDD
JAN/01/2007 17:30 PR1
Start
End
00:19:10
00:41:20
Do you want to delete?
(Deleted part will not be restored.)
Yes
No

End
• Playback related buttons : (PLAY (
), SEARCH (
).
5. Press the OK button at the end point.
The image and end point time is displayed in the Section deletion
ending point window.
6. Press the ◄► buttons to select Delete, then Press the OK button.
7. Press the ◄► buttons to select Yes, then press the OK button.
The selected section has been deleted.
00:41:20
Delete
& PLAY/PAUSE
<MOVE
• Select the start and end points of the section you want to delete
using the playback related buttons.
Partial Delete
Title List No. 001
Start
➃
➁
Return
  SCAN
sSELECT
rRETURN
eEXIT
8. Press the ◄► buttons to select Return, then press the OK button
to finish the operation.
M  The length of the section to be deleted must be at least 5
seconds long.
 The section cannot be deleted when it includes a still picture.
 Press the EXIT (
) button after the operation has finished.
The Title List screen will disappear.
Editing
 End point cannot be marked earlier than start point
English - 77
01392A_HR750_XEU-ENG-0423.indd 77
2007-04-24
9:33:40
HDD
JAN/01/2007 17:30 PR1
Title List
1/3
No.
Title
Using the Sort function (Title List)
Length
SXCV
001 JAN/01/2007 17:30 PR 01:00:00
002 JAN/02/2007 21:00 PR 01:00:00
003 JAN/03/2007 23:15 PR 00:30:00
3 MPEG2
Date
Name
17:30
4 JAN/01/2007
Length
1 SP
V-Mode Compatibility
Channel
Edit
Info
Sort
Go to
Contents
a CHECK
eEXIT
When you need to change the Sort order of Title List, you can
change it simply.
You can sort by Date, Name, Length, Channel info. Sorted list will
be resorted in chronical order upon reentering Title List.
1. While the list menu is displayed, press the GREEN(B) button to
select Sort.
2. Press the ▲▼ buttons to select the desired item, then press the OK
or ► button.
• Date : In order of when the titles were recorded
• Name : In alphabetical order
• Length : In order of recorded title length.
• Channel Info : In order of Channel information.
M  You can sort by Date, Name, Length, Channel info. Sorted list
will be resorted in copied order upon reentering Title List.
Navigation Menu
HDD
JAN/01/2007 17:30 PR1
Title List
1/3
No.
Title
Time Navigation
SXC
Length
001 JAN/01/2007 17:30 PR 01:00:00
002 JAN/02/2007 21:00 PR 01:00:00
003 JAN/03/2007 23:15 PR 00:30:00
(VR mode)
3 MPEG2
4 JAN/01/2007 17:30
1 SP
V-Mode Compatibility
Edit
Sort
Go to
Contents
a CHECK
eEXIT
HDD
JAN/01/2007 17:30 PR1
Title List
1/3
No.
Title
Length
001 JAN/01/2007 17:30 PR 01:00:00
002 JAN/02/2007 21:00 PR 01:00:00
003 JAN/03/2007 23:15 PR 00:30:00
3 MPEG2
4 JAN/01/2007 17:30
1 SP
V-Mode Compatibility
Editing
Edit
Go to
Contents
a CHECK
eEXIT
HDD
3JAN/01/2007 17:30 PR1
Time Navigation
1/3
00:00
17:30
<MOVE
18:30
sSELECT
rRETURN
N Using the TITLE LIST button
1. With the unit in Stop mode/Playback mode, press the TITLE LIST
button.
2. Press the ▲▼ buttons to select an entry you want to play from Title
List, then press the YELLOW(C) button.
Playlist
Time Navigation
Scene Navigation
Sort
Using this function, you can search scene minute-by-minute from
the recorded title list.
eEXIT
3. Press the ▲▼ buttons to select Time Navigation, then press the
OK or ► button.
4. Press the ◄► buttons to skip one minute at a time and search the
desired scene, then press the OK or PLAY ( ) button.
M  Cursor does not move if the selected recorded title is shorter
than 1 minute.
 The Navigation function may not work on a disc that has not
been recorded by this device.
 An edited title may not display the exact search time.
English - 78
01392A_HR750_XEU-ENG-0423.indd 78
2007-04-24
9:33:45
Scene Navigation
HDD
JAN/01/2007 17:30 PR1
Title List
1/3
No.
Title
SXC
Length
001 JAN/01/2007 17:30 PR 01:00:00
002 JAN/02/2007 21:00 PR 01:00:00
003 JAN/03/2007 23:15 PR 00:30:00
(VR mode)
3 MPEG2
4 JAN/01/2007 17:30
1 SP
V-Mode Compatibility
Edit
Sort
Go to
Contents
a CHECK
eEXIT
HDD
JAN/01/2007 17:30 PR1
Title List
1/3
No.
Title
Length
001 JAN/01/2007 17:30 PR 01:00:00
002 JAN/02/2007 21:00 PR 01:00:00
If there is a title composed of markers (See page 45), you can
search the desired scene using the Scene Navigation.
N Using the TITLE LIST button
1. With the unit in Stop mode/Playback mode, press the TITLE LIST
button.
003 JAN/03/2007 23:15 PR 00:30:00
3 MPEG2
4 JAN/01/2007 17:30
Edit
Sort
Go to
Contents
a CHECK
eEXIT
HDD
JAN/01/2007 17:30 PR1
01
00:00:05 02
2. Press the ▲▼ buttons to select an entry you want to play from Title
List, then press the YELLOW(C) button.
Playlist
Time Navigation
Scene Navigation
1 SP
V-Mode Compatibility
Scene Navigation
Scene No. 1/3
00:00:35 03
3. Press the ▲▼ buttons to select Scene Navigation, then press the
OK or ► button.
4. Press the ▲▼◄► buttons to select desired scene, then press the
OK or PLAY ( ) button.
00:01:05
M  Scene Navigation will not operate if a selected title does not
sPLAY
eEXIT
HDD
JAN/01/2007 17:30 PR1
Title List
1/3
No.
Title
have Markers.
Select Contents
SXCV
Length
001 JAN/01/2007 17:30 PR 01:00:00
002 JAN/02/2007 21:00 PR 01:00:00
003 JAN/03/2007 23:15 PR 00:30:00
3 MPEG2
Title
DivX
Music
Photo
4 JAN/01/2007 17:30
1 SP
V-Mode Compatibility
Edit
Sort
1. Press the BLUE(D) button to select Contents.
Go to
Contents
a CHECK
eEXIT
2. Press the ▲▼ buttons to select the contents you want to move, then
Press the OK or ► button.
M  This function is possible only when the disc contains the
selected contents.
Editing
English - 79
01392A_HR750_XEU-ENG-0423.indd 79
2007-04-24
9:33:49
HDD
JAN/01/2007 17:30 PR1
Title List
1/3
No.
Title
Advanced Editing (Playlist)
Length
001 JAN/01/2007 17:30 PR 01:00:00
002 JAN/02/2007 21:00 PR 01:00:00
003 JAN/03/2007 23:15 PR 00:30:00
3 MPEG2
4 JAN/01/2007 17:30
Creating a Playlist
1 SP
V-Mode Compatibility
Edit
Sort
Go to
Contents
a CHECK
eEXIT
SXC
(VR mode)
HDD
JAN/01/2007 17:30 PR1
Delete
Copy
Rename
Protection
Partial
Delete
3 MPEG2
Split4 JAN/01/2007 17:30
New1Playlist
SP
V-Mode
Select
All Compatibility
Edit
Title List
1/3
No.
Title
Length
001 JAN/01/2007 17:30 PR 01:00:00
002 JAN/02/2007 21:00 PR 01:00:00
003 JAN/03/2007 23:15 PR 00:30:00
Sort
Go to
Contents
a CHECK
eEXIT
HDD
New Playlist
Make Playlist
Scene No. 001
Title List 1/3
Start
End
00:08:38
00:00:00
►
00:08:38
Start
End
Make
& PLAY/PAUSE
Return
  SCAN
<MOVE
sSELECT
# $ SKIP
rRETURN
eEXIT
HDD
New Playlist
Make Playlist
Scene No. 001
Title List 1/3
Start
End
00:08:38
00:11:03

Start
Make
& PLAY/PAUSE
<MOVE
Return
  SCAN
sSELECT
rRETURN
N Using the TITLE LIST button
1. With the unit in Stop mode/Playback mode, press the TITLE LIST
button.
2. Press the RED(A) button.
The Edit menu is displayed.
3. Press the ▲▼ buttons to select New Playlist, then press the OK or
► button.
The Make Playlist screen is displayed.
4. Press the OK button at the start point.
• The image and time at the start point is displayed on the Start
window.
• The yellow-coloured selection bar moves to the End item.
00:11:03
End
Follow these instructions to create a new playlist entry from a
recorded title.
• Select the starting point of the section from which you want to
create a new scene using the playback related buttons
), SKIP (
)).
(PLAY ( ), SEARCH (
# $ SKIP
eEXIT
5. Press the OK button at the end point.
• The image and end point time is displayed in the End window.
• The yellow-coloured selection bar moves to the Make item.
6. Press the ◄► buttons to select Make, then press the OK button.
• To make a scene for the playlist.
A new Make scene screen is displayed. Repeat steps 4~6 to
make a new scene for the playlist.
A new scene will be added to the current playlist.
You can check and see all the scenes on the Edit playlist screen.
(See page 82)
Editing
• To make a new playlist.
Repeat steps 1~6 if you want to make a new playlist.
7. Press the ◄► button to select Return, then press the OK button to
finish the operation.
M  You can create up to 99 playlist entries.
 Depending on the kind of disc, the displayed screen may have
a slight difference.
English - 80
01392A_HR750_XEU-ENG-0423.indd 80
2007-04-24
9:33:53
Playing Entries in the Playlist
HDD
JAN/02/2007 13:47
Playlist
1/3
No.
Title
SXC
Length
001 JAN/02/2007 13:47
00:06:09
002 JAN/02/2007 13:51
00:03:33
003 JAN/02/2007 14:08
00:01:54
(VR mode)
i PLAYLIST
4 JAN/02/2007 13:47
Follow these instructions to play the playlist entries.
7 6 Scenes
Edit
Sort
Title List
a CHECK
eEXIT
N Using the PLAY LIST button
1. With the unit in Stop mode/Playback mode, press the PLAY LIST
button.
2. Press the ▲▼ buttons to select the playlist you want to play, then
press the OK or PLAY ( ) button.
3. Press the STOP ( ) button to stop playing.
The screen returns to the Playlist screen.
HDD
JAN/02/2007 13:47
Playlist
1/3
No.
Title
Renaming a Playlist Entry
SXC
Length
001 JAN/02/2007 13:47
00:06:09
002 JAN/02/2007 13:51
00:03:33
003 JAN/02/2007 14:08
00:01:54
(VR mode)
i PLAYLIST
4 JAN/02/2007 13:47
Follow these instructions to rename a playlist entry, i.e. to edit the
title of a playlist entry.
7 6 Scenes
Edit
Sort
Title List
a CHECK
HDD
JAN/02/2007 13:47
Playlist
1/3
No.
Delete
Copy
Rename
i PLAYLIST
Edit4
Playlist
JAN/02/2007 13:47
New7Playlist
6 Scenes
Select All
Edit
eEXIT
Title
Length
001 JAN/02/2007 13:47
00:06:09
002 JAN/02/2007 13:51
00:03:33
003 JAN/02/2007 14:08
00:01:54
Sort
Title List
a CHECK
HDD
eEXIT
Rename
D o l p h in
N Using the PLAY LIST button
1. With the unit in Stop mode/Playback mode, press the PLAY LIST
button.
2. Press the ▲▼ buttons to select the title you want to Rename from
the Playlist, then press the RED(A) button.
The Edit menu is displayed.
3. Press the ▲▼ buttons to select Rename, then press the OK or ►
button.
The Rename screen is displayed.
4. Select the desired characters using the ▲▼◄► buttons, then press
the OK button.
Back Space
mMOVE
Space
sSELECT
Clear
rRETURN
Save
eEXIT
• Back Space (RED(A) button) : Deletes and moves the cursor
backwards by one position.
• Space (GREEN(B) button) : Enters a blank and moves the
cursor one forward (to the right).
• Save (BLUE(D) button) : Registers the character inputs.
5. Press the BLUE(D) button to select Save.
The changed title is displayed in the title field of the selected playlist
entry.
Editing
• Clear (YELLOW(C) button) : Deletes all the character inputs.
English - 81
01392A_HR750_XEU-ENG-0423.indd 81
2007-04-24
9:33:57
Editing a Scene for the Playlist
HDD
JAN/02/2007 13:47
Playlist
1/3
No.
Title
SXC
Length
001 JAN/02/2007 13:47
00:06:09
002 JAN/02/2007 13:51
00:03:33
003 JAN/02/2007 14:08
00:01:54
(VR mode)
i PLAYLIST
4 JAN/02/2007 13:47
Follow these instructions to edit scenes for a playlist.
7 6 Scenes
Edit
Sort
Title List
a CHECK
eEXIT
HDD
JAN/02/2007 13:47
Playlist
1/3
No.
Delete
Copy
Rename
i PLAYLIST
Edit4
Playlist
JAN/02/2007 13:47
New7Playlist
6 Scenes
Select All
Edit
Title
Length
001 JAN/02/2007 13:47
00:06:09
002 JAN/02/2007 13:51
00:03:33
003 JAN/02/2007 14:08
00:01:54
Sort
Title List
a CHECK
HDD
JAN/02/2007 13:47
eEXIT
Edit Playlist
Scene No. 1/6
01
00:02:24
02
05
0:00:09
06
Modify
0:00:34
03
00:00:31
00:01:06
07
00:00:00
Move
04
N Using the PLAY LIST button
1. With the unit in Stop mode/Playback mode, press the PLAY LIST
button.
2. Press the ▲▼ buttons to select the title you want to edit from the
Playlist, then press the RED(A) button.
The Edit menu is displayed.
3. Press the ▲▼ buttons to select Edit Playlist, then press the OK or
► button.
The Edit Playlist screen is displayed.
0:01:22
Add
Delete
sPLAY
eEXIT
Playing a Selected Scene
4. Press the ▲▼◄► buttons to select the scene you want to play,
then press the OK or PLAY ( ) button.
The selected scene is played.
• To stop scene play, press the STOP (
) button.
Modifying a Scene (Replacing a Scene)
Editing
HDD
JAN/02/2007 13:47
Edit Playlist
Scene No. 1/6
01
00:02:24
02
05
0:00:09
06
Modify
0:00:34
03
00:00:31
00:01:06
07
00:00:00
Move
04
0:01:22
Add
Delete
sPLAY
HDD
JAN/02/2007 13:47
eEXIT
Modify Scene
Scene No. 001
Title List 1/3
Start
End
00:04:54
00:00:00
►
Start
00:05:27
End
Change
& PLAY/PAUSE
<MOVE
4-1. Press the ▲▼◄► buttons to select the scene you want to Modify,
then press the RED(A) button.
The Modify Scene screen is displayed.
5. Press the OK button at the start point of the scene.
• The image and starting point time is displayed on the Start
window.
• Select the starting or ending point of the section you want to
modify using the playback related buttons (PLAY ( ),
SEARCH (
), SKIP (
)).
Return
  SCAN
sSELECT
To setup, follow steps 1 to 3.
rRETURN
# $ SKIP
eEXIT
English - 82
01392A_HR750_XEU-ENG-0423.indd 82
2007-04-24
9:34:01
6. Press the OK button at the end point of the scene.
HDD
JAN/02/2007 13:47
Modify Scene
• The image and ending point time is displayed in the End window.
Scene No. 001
Title List: 1/3
End
00:04:54
00:06:25

00:06:25
Start
End
Change
& PLAY/PAUSE
<MOVE
7. Press the ◄► buttons to select Change, then press the OK button.
Start
Return
  SCAN
sSELECT
• The scene you want to modify is changed with the selected
section.
# $ SKIP
rRETURN
eEXIT
Moving a Scene (Changing the Position of a Scene)
HDD
JAN/02/2007 13:47
Edit Playlist
Scene No. 1/6
01
00:02:24
02
05
0:00:09
06
0:00:34
03
00:00:31
00:01:06
07
00:00:00
04
0:01:22
To setup, follow steps 1 to 3 in page 82.
4-1. Press the ▲▼◄► buttons to select the scene you want to move
(change the position), then press the GREEN(B) button.
• A yellow selection window is displayed on the scene to be moved.
Modify
Move
Add
Delete
sPLAY
eEXIT
HDD
JAN/02/2007 13:47
Edit Playlist
Scene No. 1/6
01
00:02:24
02
0:00:34
03
05
0:00:09
06
00:01:06
07
00:00:31
04
0:01:22
5. Press the ▲▼◄► buttons to select the position to which you want
to move the selected scene, then select the OK button.
M  You cannot move the selected scene to the position of the next
scene, because the selected scene should be inserted before
that position, which requires no action.
 Depending on the kind of disc, the displayed screen may have
00:00:00
sSAVE
eEXIT
a slight difference.
Adding a Scene
HDD
JAN/02/2007 13:47
Edit Playlist
Scene No. 1/6
01
00:02:24
02
05
0:00:09
06
Modify
0:00:34
03
00:01:06
07
Move
00:00:31
04
0:01:22
00:00:00
Add
Delete
sPLAY
eEXIT
HDD
JAN/02/2007 13:47
Add Scene
Scene No. 001
Title List: 1/3
Start
End
00:01:51
00:00:00
5. Press the OK button at the starting point of the scene.
• The image and starting point time is displayed on the Start
window.
• Select the starting or ending point of the section you want to
modify using the playback related buttons (PLAY ( ),
SEARCH (
), SKIP (
)).
00:01:51
Start
End
Add
& PLAY/PAUSE
<MOVE
Return
  SCAN
sSELECT
# $ SKIP
rRETURN
eEXIT
HDD
JAN/02/2007 13:47
Add Scene
Scene No. 001
Title List: 1/3
Start
End
00:01:51
00:07:28

Start
Add
Return
  SCAN
sSELECT
rRETURN
6. Press the OK button at the end point of the scene.
• The image and end point time are displayed in the End window.
• To cancel, press the ◄► buttons to select Return, then press the
OK button.
7. Press the ◄► buttons to select Add, then press the OK button.
00:07:28
End
& PLAY/PAUSE
<MOVE
4-1. Press the ▲▼◄► buttons to select the scene that will have a new
scene inserted before it, then press the YELLOW(C) button.
The Add Scene screen is displayed.
Editing
►
To setup, follow steps 1 to 3 in page 82.
• The section you want to add is inserted prior to the scene
selected in step 4-1 of Adding a Scene.
# $ SKIP
eEXIT
English - 83
01392A_HR750_XEU-ENG-0423.indd 83
2007-04-24
9:34:08
Deleting a Scene
HDD
JAN/02/2007 13:47
Edit Playlist
Scene No. 1/6
01
00:02:24
02
05
0:00:09
06
Modify
0:00:34
03
00:00:31
00:01:06
07
00:00:00
Move
04
Add
sPLAY
HDD
JAN/02/2007 13:47
01
Yes
0:00:09
06
Modify
<MOVE
4-1. Press the ▲▼◄► buttons to select the scene you want to delete,
then press the BLUE(D) button.
• The message “Do you want to delete the scene?” is displayed.
Delete
eEXIT
5. Press the ◄► buttons to select Yes, then press the OK to delete
the selected scene.
Edit Playlist
Scene No. 1/6
00:02:24 Do02you want
0:00:34to delete
03
00:00:31
04
the scene?
05
0:01:22
To setup, follow steps 1 to 3 in page 82.
0:01:22
No
00:01:06
07
Move
00:00:00
Add
sSELECT
rRETURN
Delete
eEXIT
Deleting a Playlist Entry from the Playlist
HDD
JAN/02/2007 13:47
Playlist
1/3
No.
Title
Length
001 JAN/02/2007 13:47
00:06:09
002 JAN/02/2007 13:51
00:03:33
003 JAN/02/2007 14:08
00:01:54
i PLAYLIST
1. With the unit in Stop mode/Playback mode, press the PLAY LIST
button.
4 JAN/02/2007 13:47
7 6 Scenes
Edit
Sort
Title List
a CHECK
HDD
JAN/02/2007 13:51
Delete
Copy
i PLAYLIST
New4Playlist
JAN/02/2007 13:51
Scenes
Select
7 6All
Unselect All
Title
00:06:09
002 JAN/02/2007 13:51
00:03:33
003 JAN/02/2007 14:08
00:01:54
Sort
Title List
HDD
JAN/02/2007 13:51
Edit
Title
Length
001 JAN/02/2007 13:47
00:06:09
002 JAN/02/2007 13:51
00:03:33
2 items003
areJAN/02/2007
selected 14:08
Do you want to delete?
00:01:54
4 JAN/02/2007 13:51
Yes
Sort
sSELECT
Editing
<MOVE
eEXIT
Playlist
2/3
No.
7 6 Scenes
Length
001 JAN/02/2007 13:47
a CHECK
i PLAYLIST
eEXIT
Playlist
2/3
No.
Edit
N Using the PLAY LIST button
No
Title List
rRETURN
eEXIT
2. Press the ▲▼ buttons to select an entry you want to delete in the
Playlist, then press the MARKER button until a checkmark
appears. Repeat this step to select an additional title you want to
delete.
• If you don’t want to delete a certain one of the checked entries,
simply select that entry and press the MARKER button to
deselect it until a checkmark disappears.
3. Press the RED(A) button to select Edit.
Edit menu is displayed.
4. Press the ▲▼ buttons to select Delete, then press the OK or ►
button.
• You will be prompted with the delete confirmation message “Do
you want to delete?”.
5. Press the ◄► buttons to select Yes, then press the OK button.
You will be automatically returned to the Playlist screen after the
delete operation has finished.
M  If you select “Select All” in the Edit menu, all title will be
checked.
English - 84
01392A_HR750_XEU-ENG-0423.indd 84
2007-04-24
9:34:17
Using the Sort (Playlist)
HDD
JAN/02/2007 13:47
Playlist
1/3
No.
Title
When you need to change the Sort order of Playlist, you can
change it simply.
Length
001 JAN/02/2007 13:47
00:06:09
002 JAN/02/2007 13:51
00:03:33
003 JAN/02/2007 14:08
00:01:54
i PLAYLIST
1. While the list menu is displayed, press the GREEN(B) button to
select Sort.
4 JAN/02/2007 13:47
7 6 Scenes
Edit
Date
Name
Sort
Title List
a CHECK
2. Press the ▲▼ buttons to select the desired item, then press the OK
or ► button.
eEXIT
• Date : In order of when the playlists were created
• Name : In alphabetical order
M  You can sort by Date, Name. Sorted list will be resorted in
copied order upon reentering Playlist.
Copying from HDD to DVD
About the Copy Screen
➀
HDD
Selected Items:
Copy
Avallable : 4099MB
To : DVD
Source : HDD
➁
001 JAN/01/2007 1
➃
DVD
002 JAN/01/2007 1
3 MPEG2
003 JAN/01/2006 1
8 47MB
Sort
➁ Title to be copied
➅
➃ The location where the copied files are stored
Selection
a CHECK
➄
➀ Total size and number of selected titles for copying
➂ This shows available disc space
0 SP
Start Copy
➂
➆
eEXIT
➄ Copy start button
➅ Sort button (Date, Name, Length, Channel Info)
➆ Selection button
- Select All : All entries in the current folder will be checked.
- Unselect All : All checked entries will be unchecked.
Contents Copy Specifications
HDD DVD
Contents
Recorded Video Title
Supported
Copy Protected Title
Not supported
Copy Once Title
Move
(Deletes the Title in the HDD after copying)
The Copy is possible only with CPRM-Compatible disc.
But “Copy Once programme” has been recorded on the HDD, this title
can be copied to DVD-RW(VR mode) or DVD-RAM.
Editing
Once “Copy Once programme” has been recorded on the DVD disc,
this title cannot be copied to HDD anymore.
N Using the TITLE LIST button
1. Press the OPEN/CLOSE button and place a recordable disc on the
disc tray.
2. Press the OPEN/CLOSE button to close the disc tray. Wait until
LOAD disappears from the front panel display. Check that the disc
has enough available space for the recording.
English - 85
01392A_HR750_XEU-ENG-0423.indd 85
2007-04-24
9:34:24
HDD
JAN/01/2007 17:30 PR1
Title List
1/3
No.
Title
Length
001 JAN/01/2007 17:30 PR 01:00:00
002 JAN/02/2007 21:00 PR 01:00:00
003 JAN/03/2007 23:15 PR 00:30:00
3 MPEG2
4 JAN/01/2007 17:30
Sort
HDD
Selected Items:
Go to
Contents
a CHECK
eEXIT
Copy
Avallable : 4099MB
Source : HDD
To : DVD
001 JAN/01/2007 1
DVD
002 JAN/01/2007 1
003 JAN/01/2006 1
3 MPEG2
8 47MB
Sort
Selection
a CHECK
• During Playback, you can also copy the title by pressing the
COPY button.
6. Press the ▲▼ buttons to select the title you wan to copy, then press
the MARKER button until a checkmark appears.
Repeat this step to select an additional title you want to copy.
• If you don’t want to copy a certain one of the checked entries,
simply select that entry and press MARKER button to deselect it
until a checkmark disappears.
0 SP
Start Copy
4. With the unit in Stop mode/Playback mode, press the TITLE LIST
button.
5. Press the COPY button. Copy screen is displayed.
1 SP
V-Mode Compatibility
Edit
3. Select the HDD by pressing the HDD button on the front panel of
the HDD & DVD RECORDER or on the remote control.
eEXIT
7. Press the RED(A) button to select Start Copy.
HDD
Selected Items: 47MB (1)
Source : HDD
Copy
Avallable : 3975MB
To : DVD
001 JAN/01/2007 1
DVD
002 JAN/01/2007 1
• The title to be copied is not displayed on the screen, and copying
begins while the currently broadcasting programme is displayed
on the screen.
003 JAN/01/2006 1
3 MPEG2
0 SP
8 47MB
Start Copy
Sort
Selection
a CHECK
eEXIT
• Press the INFO button to change the copy processing bar.
If you press INFO button again, copy processing bar will be
appeared.
• To cancel the copying in progress, press the RED(A) button.
8. After a successful copy, “The title is successfully copied” message
is displayed.
x
21%
Cancel
b Bar Type
c Channel
Editing
The title is successfully copied.
English - 86
01392A_HR750_XEU-ENG-0423.indd 86
2007-04-24
9:34:26
DVD-RAM(VR)
JAN/01/2007 17:30 PR1
Title List
1/3
No.
Title
Copying from DVD to HDD
Length
001 JAN/01/2007 17:30 PR 01:00:00
002 JAN/01/2007 21:00 PR 01:02:06
003 JAN/01/2007 23:15 PR 00:01:03
3 MPEG2
N Using the TITLE LIST button
4 JAN/01/2007 17:30
1 SP
Edit
Sort
Go to
Contents
a CHECK
eEXIT
1. Press the OPEN/CLOSE button and place a recorded disc on the
disc tray.
2. Press the OPEN/CLOSE button to close the disc tray.
DVD-RAM(VR)
Selected Items: 47MB (1)
Source : DVD
Copy
Avallable : 235993MB
To : HDD
001 JAN/01/2007 1
HDD
3. With the unit in Stop mode/Playback mode, press the TITLE LIST
button.
002 JAN/01/2007 1
4. Press the COPY button. Copy screen is displayed.
003 JAN/01/2006 1
3 MPEG2
0 SP
8 47MB
Start Copy
Sort
• During Playback, you can also copy the title by pressing the
COPY button.
Selection
a CHECK
eEXIT
5. Press the ▲▼ buttons to select the title you want to copy, then
press the MARKER button until a checkmark appears.
Repeat this step to select an additional title you want to copy.
• If you don’t want to copy a certain one of the checked entries,
simply select that entry and press MARKER button to deselect it
until a checkmark disappears.
x
21%
Cancel
b Bar Type
c Channel
6. Press the RED(A) button to select Start Copy.
• Press the INFO button to change the copy processing bar.
If you press INFO button again, copy processing bar will be
appeared.
The title is successfully copied.
• To cancel the copying in progress, press the RED(A) button.
7. After a successful copy, “The title is successfully copied.” message
is displayed.
M  You cannot copy anything else on finalised DVD-R and
DVD-RW(V mode) mode.
 You cannot copy a DVD-VIDEO to HDD.
Contents Copy Specifications
Contents
DVD HDD
Recorded Video Title
Supported
Copy Protected Title
Not supported
Copy Once Title
Not supported
Editing
English - 87
01392A_HR750_XEU-ENG-0423.indd 87
2007-04-24
9:34:31
CD
Selected Items: 5.85MB (1)
Copy
Source : DVD
To :
When you copy MP3/JPEG/DivX files from HDD to DVD, only
DVD-RW(V)/-R discs are available.
E HDD
Y ROOT
001 Song 10.mp3
9 MP3
8 5.85MB
Copying MP3, JPEG or DivX
Avallable :
002 Song 1.mp3
003 Song 2.mp3
004 Song 3.mp3
005 Song 4.mp3
Start Copy
Sort
Select All
a CHECK
CD
Selected Items: 9.68MB (2)
Unselect All
Copy
Avallable : 236724MB
Source : DVD
t ROOT
001 Song 10.mp3
9 MP3
8 3.84MB
002 Song 1.mp3
003 Song 2.mp3
004 Song 3.mp3
005 Song 4.mp3
Start Copy
New Folder
eEXIT
CD
Selected Items: 9.68MB (2)
Copy
Avallable : 236724MB
Source : DVD
002 Song 1.mp3
6. Press the ▲▼ buttons to select the MP3, Photo or DivX file you
want to copy, then press the MARKER button until a checkmark
appears.
003 Song 2.mp3
004 Song 3.mp3
005 Song 4.mp3
Start Copy
New Folder
Rename
eEXIT
CD
Selected Items: 9.68MB (2)
Copy
Avallable : 236724MB
Source : DVD
To : HDD
Y ROOT
t ROOT
001 Number
Song 10.mp3
of item
9 MP3
8 3.84MB
002 Song 1.mp3
003 Song 2.mp3
Start
004 Song 3.mp3
EXIT
New Folder
• You can create a new folder by pressing the GREEN(B) button.
Rename
eEXIT
CD
Selected Items: 9.68MB (2)
Source
: DVD
Copying...
Y ROOT
Free space
: 236623 MB
Song
Number of001
item
: 110.mp3
/2
Song 1.mp3
1.mp3
File Name 002
: Song
9 MP3
8 3.84MB
• If you don’t want to copy a certain one of the checked entries,
simply select that entry and press MARKER button to deselect it
until a checkmark disappears.
7. Press the ► button, then press the OK button to make the first
folder where the copied files are stored.
:2
005 Song 4.mp3
Start Copy
4. Press the ▲▼ buttons to select Music, Photo or DivX, then press
the OK or ► button.
5. Press the COPY button. Copy screen is displayed.
t ROOT
E MP3
001 Song 10.mp3
8 3.84MB
3. Press the ▲▼ buttons to select Library, then press the OK or ►
button.
To : HDD
Y ROOT
9 MP3
1. Insert a JPEG disc, MP3 disc or DivX disc into the disc tray.
2. Press the OPEN/CLOSE button to close the disc tray. Wait until
LOAD disappears from the front panel display. Check that the disc
has enough available space for the recording.
To : HDD
Y ROOT
File Copy
eEXIT
Copy
Avallable : 236724MB
To : HDD
t ROOT
003 Song 2.mp3
8. Press the RED(A) button to select Start Copy.
The message “Number of item : x” is displayed.
9. Press the ◄► buttons to select Start, then press the OK button.
File copy begins.
• To cancel the copying in progress, press the EXIT (
33%
) button.
004 Song 3.mp3
005 Song 4.mp3
Start Copy
New Folder
Rename
eEXIT
CD
Selected Items: 76.8MB (2)
Source : DVD
Copy
Avallable : 236715MB
Y ROOT
E HDD
1. Insert a Disc (JPEG, MP3 or DivX) into the tray.
E MP3 (1)
9 MP3
Editing
8 40.2MB
Start Copy
E MP3 (2)
2. Press the ▲▼ buttons to select Library, then press the OK or ►
button.
E MP3 (3)
Sort
Select All
a CHECK
CD
Selected Items: 76.8MB (2)
Source : DVD
Unselect All
eEXIT
Copy
Avallable : 236715MB
4. Press the COPY button. Copy screen is displayed.
t ROOT
E MP3 (1)
8 36.6MB
Start Copy
3. Press the ▲▼ buttons to select Music, Photo or DivX then press
the OK or ► button.
MP3, JPEG or DivX folder is displayed.
To : HDD
Y ROOT
9 MP3
Folder Copy
To :
E MP3 (2)
5. Press the ▲▼ buttons to select the folder you want to copy, then
press the MARKER button until a checkmark appears.
E MP3 (3)
New Folder
eEXIT
• If you don’t want to copy a certain one of the checked folders,
simply select that entry and press MARKER button to deselect it
until a checkmark disappears.
English - 88
01392A_HR750_XEU-ENG-0423.indd 88
2007-04-24
9:34:35
CD
Selected Items: 76.8MB (2)
Copy
Avallable : 236715MB
Source : DVD
To :
Y ROOT
9 MP3
8 36.6MB
Start Copy
• You can create a new folder by pressing the GREEN(B) button.
t ROOT
E MP3Number
(1)
of item : 24
7. Press the RED(A) button to select Start Copy.
The message “Number of item : x” is displayed.
E MP3 (2)
E MP3 (3)
Start
EXIT
New Folder
eEXIT
CD
Selected Items: 76.8MB (2)
Source
: DVD
Copying...
Y ROOT
Free space
: 236615 MB
MP3: (1)
Number ofE
item
1 / 24
MP3
(2) ## 1.mp3
File Name E
: 01.
###
9 MP3
8 36.6MB
Start Copy
6. Press the ►▲▼ or OK button to select the location where the
copied files are stored.
E MP3 (3)
Copy
Avallable : 236715MB
To :
8. Press the ◄► buttons to select Start, then press the OK button.
Folder copy begins.
Subfolders and files in the selected folder are copied.
• To cancel the copying in progress, press the EXIT (
) button.
t ROOT
M  Pressing the EXIT (
) button during folder copying will cancel
the folder copying after the current file is copied.
33%
New Folder
 You can copy up to 500 including files and sub folders to one
eEXIT
folder. [ MP3, JPEG, DivX ]
 If you want to file copy, you should create a new folder before
starting a copy.
You cannot copy to top-level(ROOT) folder directly without
creating a new folder.
 If the top-level (ROOT) folder has had already 500 including
folders, you should delete one or more items before you can
create a new folder.
 Files having an existing name of ***.mp3/***.jpg, are
automatically renamed to ***01.mp3/***01.jpg and copied.
 It allows up to 999 copies to have the same name.
 You cannot copy an Audio CD.
 File size on a disc and the copied file in the HDD may be
slightly different due to the file system.
 If you check some entries in the current folder and move to
open a different folder, those entries are automatically
unchecked and excluded from the selection list.
Contents Copy Specifications
Contents
MP3
HDD DVD
DVD HDD
Supported
Supported
JPEG(photo)
Supported
Supported
DivX
Supported
Supported
• HDD DVD-R, DVD-RW(V)
Editing
• Disc(CD-R/ CD-RW/DVD-RAM/DVD-R(Finalise)/DVD-RW(Finalise))
HDD
• The disc that has Video recording or has title dubbing from HDD
can’t be copied.
• If the disc is finalised through Disc Manager, it can be compatible
with PC as a disc with a UDF file system.
English - 89
01392A_HR750_XEU-ENG-0423.indd 89
2007-04-24
9:34:45
HDD
Q Song 1.mp3
Music List
No.
Title
Changing the name of Music/Photo/DivX file
Size
S
Y ROOT
Copy
Delete
  ►   00:00:00
Rename
Song 1.mp3
New9Playlist
E Playlist
ROOT
Go To
Select All
Edit
001 Song 1.mp3
3.8 MB
002 Song 2.mp3
3.8 MB
003 Song 3.mp3
5.1 MB
004 Song 4.mp3
9.2 MB
005 Song 5.mp3
5.2 MB
006 Song 6.mp3
10.3 MB
Sort
Play Mode
#/$ PREVIOUS/NEXT PAGE
a CHECK
HDD
Contents
eEXIT
Rename
Back Space
Space
Clear
sSELECT
rRETURN
HDD
Q Dream.mp3
Save
eEXIT
Music List
1/9
No.
Title
00:00:00
9 Dream.mp3
E ROOT
Edit
Q Dream.mp3
3.8 MB
002 Song 2.mp3
3.8 MB
003 Song 3.mp3
5.1 MB
004 Song 4.mp3
9.2 MB
005 Song 5.mp3
5.2 MB
006 Song 6.mp3
10.3 MB
Sort
#/$ PREVIOUS/NEXT PAGE
Play Mode
a CHECK
3. Select the desired characters using the ▲▼◄► buttons, then press
the OK button.
Back Space (RED(A) button): Deletes and moves the cursor
backwards by one position.
Size
Y ROOT
►
1. Press the ▲▼ buttons to select the entry you want to rename, then
press the RED(A) button.
2. Press the ▲▼ buttons to select Rename, then press the OK or
► button.
Rename Screen is displayed.
Dream
mMOVE
You can rename a Music, Photo or DivX file copied to HDD.
Contents
Space (GREEN(B) button): Enters a blank and moves the cursor
one forward (to the right).
Clear (YELLOW(C) button): Deletes all the character inputs.
Save (BLUE(D) button): Registers the character inputs.
eEXIT
Editing
4. Press the BLUE(D) button to select Save.
The changed file name is displayed on the selected entry.
English - 90
01392A_HR750_XEU-ENG-0423.indd 90
2007-04-24
9:34:48
DVD-RAM(VR)
Disc Manager
Disc Name
DVD-VR
Used Space
00:17
( 0.52 GB)
Available Space
01:54 SP
( 3.85 GB)
Disc Protection Info
Not Protected
Current Rec. Mode
VR-Mode
Rename
<MOVE
Protection
Delete All
sSELECT
rRETURN
DVD-RAM(VR)
Disc Manager
Editing the Disc Name
XCV
Format
eEXIT
Rename
Follow these instructions to give a name to a disc.
1. With the unit in Stop mode, press the MENU button.
DISC–1
2. Press the ▲▼ buttons to select Disc Manager, then press the OK
or ► button.
Back Space
mMOVE
Space
Clear
sSELECT
rRETURN
Save
eEXIT
3. Press the ◄► buttons to select Rename, then press the OK button.
The Rename screen is displayed.
4. Select the desired characters using the ▲▼◄► buttons, then press
the OK button.
5. Press the BLUE(D) button to select Save.
A disc name is given to the disc.
M  You may need to clear Disc Protection beginning editing.
 Depending on the kind of disc, the displayed screen may be
different.
DVD-RAM(VR)
Disc Manager
Disc Name
DVD-VR
Used Space
00:17
( 0.52 GB)
Available Space
01:54 SP
( 3.85 GB)
Disc Protection Info
Not Protected
Current Rec. Mode
VR-Mode
Rename
<MOVE
Protection
Delete All
sSELECT
rRETURN
DVD-RAM(VR)
DVD-VR
Used Space
00:17
( 0.52 GB)
Available Space
01:54 SP
( 3.85 GB)
Disc Protection Info
eEXIT
Protection
rRETURN
1. With the unit in Stop mode, press the MENU button.
2. Press the ▲▼ buttons to select Disc Manager, then press the OK
or ► button.
Format
4. Press the ◄► buttons to select On, then press the OK button.
Editing
sSELECT
Off
Delete All
Disc Protection allows you to protect your discs from being
formatted or deleted due to unintended operations.
3. Press the ◄► buttons to select Protection, then press the OK
button.
VR-Mode
On
<MOVE
Format
Disc Protection:
Not Protected
Current Rec. Mode
Rename
XCV
Disc Manager
Disc Name
Disc Protection
eEXIT
English - 91
01392A_HR750_XEU-ENG-0423.indd 91
2007-04-24
9:34:52
Delete All Title Lists
DVD-RAM(VR)
Disc Manager
Disc Name
DVD-VR
Used Space
00:17
( 0.52 GB)
Available Space
01:54 SP
( 3.85 GB)
Disc Protection Info
Not Protected
Current Rec. Mode
VR-Mode
XCV
1. With the unit in Stop mode, press the MENU button.
Rename
Protection
<MOVE
Delete All
sSELECT
Format
rRETURN
DVD-RAM(VR)
eEXIT
Disc Manager
Disc Name
DVD-VR
Used Space
00:17
( 0.52 GB)
Available Space
01:54 SP
( 3.85 GB)
VR-Mode
Yes
Rename
<MOVE
No
Protection
Delete All
sSELECT
3. Press the ▲▼◄► buttons to select Delete All, then press the OK
button.
• You will be prompted with the confirmation message “Do you
want to delete all title lists?”.
you want to Not
delete
all title lists?
Disc ProtectionDo
Info
Protected
Current Rec. Mode
2. Press the ▲▼ buttons to select Disc Manager, then press the OK
or ► button.
Format
rRETURN
eEXIT
• When Protected Entry exists: The Delete All Title List function will
not operate. If there is a title containing a still picture, however,
that function will not operate.
If you want to delete a protected entry, disable Protect for it on the
Lock item.
• When protected a DVD-RAM/-RW is used, data cannot be
deleted from a disc.
• If you select Yes, you will be prompted with the confirmation
message “All playlists will also be deleted. Do you want to
continue?”.
4. Press the ◄► buttons to select Yes, then press the OK button.
All title lists are deleted.
HDD
Disc Manager
Used Space
000:39
Available Space
065:19 XP ( 231.01 GB)
Delete All Title Lists/DivX Lists /Music Lists/Photo Lists
S
( 1.68 GB)
1. With the unit in Stop mode, press the MENU button.
Delete
<MOVE
sSELECT
Format
rRETURN
HDD
eEXIT
Disc Manager
Used Space
000:39
Available Space
( 1.68 GB)
Editing
DivX
Music
Photo
Delete
<MOVE
sSELECT
rRETURN
Format
eEXIT
<Title>
HDD
Disc Manager
Used Space
000:39
Available Space
3. Press the ◄► buttons to select Delete, then press the OK button.
• When Protected Entry exists: The Delete All Title List function will
not operate. If there is a title containing a still picture, however,
that function will not operate. If you want to delete a protected
entry, disable Protect for it on the Lock item.
065:19 XP ( 231.01 GB)
Select contents to delete all
Title
2. Press the ▲▼ buttons to select Disc Manager, then press the OK
or ► button.
4. Press the ◄► buttons to select the Title, DivX, Music or Photo,
then press the OK button.
5. Press the ◄► buttons to select Yes, then press the OK button.
All title lists, DivX lists, music lists or photo lists are deleted.
( 1.68 GB)
065:19 XP ( 231.01 GB)
All playlists will also be deleted.
Do you want to continue?
Yes
No
Delete
<MOVE
sSELECT
rRETURN
Format
eEXIT
English - 92
01392A_HR750_XEU-ENG-0423.indd 92
2007-04-24
9:34:53
Formatting a Disc
HDD
Disc Manager
Used Space
000:39
Available Space
065:19 XP ( 231.01 GB)
SXC
( 1.68 GB)
Use these instructions to format a disc.
The disc protect should also be cleared.
Delete
<MOVE
sSELECT
Format
rRETURN
HDD
eEXIT
Disc Manager
Used Space
000:39
Available Space
( 1.68 GB)
065:19 XP ( 231.01 GB)
No
Delete
<MOVE
sSELECT
Format
rRETURN
DVD-RW(VR)
eEXIT
Disc Manager
Disc Name
DVD-VR
Used Space
00:17
( 0.52 GB)
Available Space
01:54 SP
( 3.85 GB)
Choose
Disc Protection
Info the
recording
Not format
Protectedfor DVD-RW.
Current Rec. Mode
VR-Mode
DVD-VR
DVD-V
Rename
Protection
<MOVE
Delete All
sSELECT
Finalise
rRETURN
2. Press the ▲▼ buttons to select Disc Manager, then press the OK
or ► button.
3. Press the ◄► buttons to select Format, then press the OK button.
Current media: HDD
Do you want format?
Yes
1. With the unit in Stop mode, press the MENU button.
Format
eEXIT
HDD/ DVD-RAM
• You will be prompted with the confirmation message“Current
media:½½½ Do you want to format?”.
• If you select Yes, you will be prompted with the confirmation
message “All data will be deleted. Do you want to continue?”.
DVD-RW
• You will be prompted with the confirmation message “Choose the
recording format for DVD-RW.”
• If you select the desired format type, you will be prompted with
the confirmation message “All data will be deleted. Do you want
to continue?”.
4. Press the ◄► buttons to select Yes, then press the OK button. The
disc is formatted.
DVD-VR and DVD-V are defined according to their recording format.
DISC
DVD-VR
DVD-V
DVD-RAM/-RW
DVD-RW/DVD-R
Editing
English - 93
01392A_HR750_XEU-ENG-0423.indd 93
2007-04-24
9:34:55
Finalising a Disc
DVD-RW(VR)
Disc Manager
Disc Name
DVD-VR
Used Space
00:17
( 0.52 GB)
Available Space
01:54 SP
( 3.85 GB)
Disc Protection Info
Not Protected
Current Rec. Mode
VR-Mode
CV
Rename
Protection
mMOVE
Delete All
Finalise
sSELECT
rRETURN
Format
eEXIT
After you record titles onto a DVD-RW/-R disc with your HDD &
DVD RECORDER, it needs to be finalised before it can be played
back on external devices.
1. With the unit in Stop mode, press the MENU button.
DVD-RW(VR)
Disc Manager
Disc Name
DVD-VR
Used Space
00:17
( 0.52 GB)
Available Space
01:54 SP
( 3.85 GB)
Do
Disc Protection Info
you want Not
to finalise
Protecteddisc?
Current Rec. Mode
3. Press the ▲▼◄► buttons to select Finalise, then press the OK
button.
VR-Mode
Yes
No
Rename
Protection
<MOVE
Delete All
Finalise
sSELECT
rRETURN
DVD-RW(VR)
Format
eEXIT
Disc Manager
Disc Name
DVD-VR
Used Space
00:17
( 0.52 GB)
01:54 SP
( 3.85 GB)
Available Space
VR-Mode
Yes
No
Rename
Protection
<MOVE
Delete All
sSELECT
Finalise
rRETURN
You will be prompted with the message “Do you want to finalise
disc?”.
4. Press the ◄► buttons to select Yes, then press the OK button.
You will be prompted again with the message “Disc will be finalised.
Do you want to continue?”.
Disc will be finalised.
NottoProtected
you want
continue?
Disc Protection Info Do
Current Rec. Mode
2. Press the ▲▼ buttons to select Disc Manager, then press the OK
or ► button.
Format
5. Press the ◄► buttons to select Yes, then press the OK button.
The disc is finalised.
eEXIT
M  Once a disc is finalised, you cannot delete entries from the
record list.
 After being finalised, the DVD-R/-RW(video mode) operates in
the same manner as a DVD-Video.
 Depending on the disc type, the displayed screen may be
different.
 Finalising time may be different depending on the amount of
data recorded on the disc.
 Data on the disc will be damaged if the recorder is powered off
during finalisation process.
 You can finalise the disc automatically using EZ Record.
Editing
(See page 29)
English - 94
01392A_HR750_XEU-ENG-0423.indd 94
2007-04-24
9:34:57
Unfinalising a Disc (V/VR mode)
DVD-RW(VR:F)
Disc Manager
Disc Name
DVD-VR
Current Rec. Mode
VR-Mode
C
1. With the unit in Stop mode, press the MENU button.
Unfinalise
<MOVE
sSELECT
rRETURN
DVD-RW(VR:F)
Format
eEXIT
Disc Manager
Disc Name
DVD-VR
Current Rec. Mode
VR-Mode
No
Unfinalise
<MOVE
sSELECT
rRETURN
DVD-RW(VR:F)
Format
eEXIT
Disc Manager
Disc Name
DVD-VR
Current Rec. Mode
VR-Mode
3. Press the ◄► buttons to select Unfinalise, then press the OK
button.
You will be prompted with the message “Do you want to unfinalise
disc?”.
Do you want to unfinalise disc?
Yes
2. Press the ▲▼ buttons to select Disc Manager, then press the OK
or ► button.
4. Press the ◄► buttons to select Yes, then press the OK button.
You will be prompted again with the message “Disc will be
unfinalised. Do you want to continue?”.
5. Press the ◄► buttons to select Yes, then press the OK button.
The disc is unfinalised.
Disc will be unfinalised.
Do you want to continue?
Yes
No
Unfinalise
<MOVE
sSELECT
rRETURN
Format
M  A DVD-RW can be finalised or unfinalised in Video mode.
eEXIT
Finalise
Unfinalise
Mark
DVD-Video(RW)
DVD-RW(V)
Operation
Same as DVD-Video
Additional recording,
protection and deletion
are possible.
 A DVD-RW can be finalised or unfinalised in VR mode.
Finalise
Unfinalise
Mark
DVD-RW(VR:F)
DVD-RW(VR)
Operation
Additional recording,
deletion, editing, and
protection are
impossible.
Additional recording,
deletion, editing, and
protection are possible.
Editing
English - 95
01392A_HR750_XEU-ENG-0423.indd 95
2007-04-24
9:34:57
Reference
icon appears on the screen.
Troubleshooting
Checkpoint 1
If your product malfunctions, go through the
checkpoints below before contacting a Samsung
authorised service centre.
(1) Your DVD disc restricts it.
(2) Your DVD disc does not support this
feature (for example: angles)
Power
(3) The feature is not available at the moment.
The input is displayed for a while when the power
is turned on.
Checkpoint 1
The HDD & DVD RECORDER requires some
time to initialize and the input will be displayed
for approx. 10 seconds after it is turned on.
(4) You’ve requested a title, chapter, or scan
time that is out of range.
Play mode settings are different from the settings
configured in the Settings menu.
Checkpoint 1
Recording
Cannot record TV programmes.
Checkpoint 1
Check whether the power cord is securely
plugged into the power outlet.
Checkpoint 2
Did you set the HDD & DVD RECORDER
channel settings correctly?
Checkpoint 3
Check the free space on your
HDD/DVD-RAM/-RW/-R discs.
The aspect ratio is fixed for DVD discs.
(See page 32)
The angle operation does not work while playing a
DVD disc.
Checkpoint 1
I pressed the REC button but there is no response.
Check available disc type. (See page 56)
If a programme is copy protected, it cannot be
recorded.
The angle operation is available only when
the disc contains images
captured from different angles.
The selected audio and/or subtitle language is not
played.
Checkpoint 1
Playback
Cannot play the disc.
Checkpoint 1
The disc does not support all selected
functions. In this case, some settings
configured in the settings menu may not work
properly.
Cannot change the aspect ratio.
Checkpoint 1
Checkpoint 1
You cannot use this operation or
function due to one of the following
reasons:
Audio and subtitle languages are
disc-specific. Only the sound and
subtitle languages contained on the DVD disc
are available and displayed in the disc menu.
Cannot copy title or file to the other mode.
Check whether the disc is inserted
correctly with the label facing up.
Check the regional code of the DVD disc.
Checkpoint 3
This HDD & DVD RECORDER cannot play
some types of discs.
(See pages 7, 36)
Checkpoint 1
DVD discs encoded with copy protection can
not be copied to HDD.
Checkpoint 2
Refer to “Contents Copy Specifications” on
page 6 to check if copying is supported.
Refer to “V-Mode Compatibility” on page 31 to
check if copying is support.
Reference
Checkpoint 2
English - 96
01392A_HR750_XEU-ENG-0423.indd 96
2007-04-24
9:34:58
Timer recording does not work properly.
Video
The disc revolves, but no image or bad quality
images is displayed.
Checkpoint 1
Be sure that the Video Setting is
properly set. (See page 32)
Checkpoint 2
Check whether there is damage to or any
foreign material on your disc.
Checkpoint 3
Some low quality discs may not play properly.
Checkpoint 4
If scenes change from dark to bright
suddenly, the screen may shake
vertically temporarily, but this is not a fault.
Re-check the recording time and the end time
settings again.
Checkpoint 2
Recording will be cancelled if the power is
interrupted due to a power failure or another
similar reason while recording.
Remote Control Unit
Sound
No sound.
Checkpoint 1
Checkpoint 1
Are you watching a programme in slow or skip
mode?
If you are playing a programme at a speed
other than normal speed, sound will not be
heard. (Except for forward search (X 2) in
disc.)
The remote control doesn’t work.
Checkpoint 1
Point the remote control at the remote control
sensor on your HDD & DVD RECORDER.
Allow for proper distance. Remove obstacles
between your HDD & DVD RECORDER and
the remote control.
Checkpoint 2
Check whether the batteries are drained.
Checkpoint 3
Check the TV/DVD selection button setting.
Checkpoint 4
Check whether TV control button is selected
or not.
Other
Checkpoint 2
Check the connections and settings.
(See pages 21~22, 30~31)
Checkpoint 3
Check whether the disc is damaged. Clean
the disc, if necessary.
Checkpoint 4
Check whether the disc is inserted
correctly with the label facing up.
I forgot my password for parental supervision.
Checkpoint 1
No audio output.
Checkpoint 1
Check whether you have selected the correct
digital output options in the Audio Output
Options menu.
(See pages 30~31)
Timer lamp flickers.
Checkpoint 1
Checkpoint 1
Read the table of contents and then find and
read the section describing your problem,
follow the instructions given.
Checkpoint 2
Plug your HDD &DVD RECORDER off and
on.
Checkpoint 3
If the problem still persists, contact a nearby
Samsung service centre.
Check there is enough space in the disc or
HDD for recording.
Check whether the current disc is recordable
or not.
Make sure to check before the start time of
recording.
A recorded disc is played with only the subtitle
and the audio signal which were selected
during recording.
Reference
Checkpoint 2
Is it possible to change a subtitle and an audio
signal on a recorded disc?
Other problems.
Timer Recording
Checkpoint 1
Press and hold the PROG (
) buttons on
the front panel of the Recorder for more than
5 seconds with no disc in the unit. All settings
including the password will revert to the
factory settings. Do not use this unless
absolutely necessary.
(Note that this function is possible only when
no disc is inserted.)
English - 97
01392A_HR750_XEU-ENG-0423.indd 97
2007-04-24
9:34:59
Specifications
General
Input
Power requirements
220-240 V AC, 50 Hz
Power consumption
32 Watts / 2,9 Watts (Power off)
Weight
3,9 Kg
Dimensions
430 mm(W) x 300 mm(D) x 59 mm(H)
Operating temp.
+5 °C to +35 °C
Other conditions
Keep level when operating. Less than 75% operating humidity
Video
Composite Video : 1.0 V p-p at 75Ω load, sync negative
Audio
Max.Audio Input Level : 2 Vrms
DV Input
IEEE 1394(4p) compatible jack
Receivable Channels
PAL-I
Scart Jack AV2 (Scart Ext)
Video : Composite, RGB Audio: analogue
Audio
Analogue output jacks x 2
Optical/Coaxial digital audio output
Composite Video : Video output jack x 1
Output
Video
S-Video output x 1 (Y:1,0Vp-p, C:0,286Vp-p at 75Ω load)
Component output x 1 (Y: 1,0Vp-p, Pb: 0,70Vp-p, Pr: 0,70Vp-p at 75Ω load)
Recording
HDD
Capacity
Scart Jack AV1 (Scart TV)
Video : Composite, RGB Audio: analogue
Picture Compression format
MPEG-II
Audio Compression format
Dolby Digital 2ch/256Kbps, MPEG-II
Recording Quality
EP (about 1,6 Mbps or about 1,2 Mbps)
Audio Frequency Response
20 Hz~20 kHz
DVD-HR749
DVD-HR750
160 GB
Audio Output
Reference
XP (about 8,5 Mbps), SP (about 4,5 Mbps), LP (about 2,5 Mbps),
For DVD discs, audio signals recorded at 96 kHz sampling frequency are converted into and
output at 48 kHz.
Disc Type
DVD
AUDIO CD(CD-DA)
Analog Audio Output
48 / 96 kHz
44,1 kHz
Digital Audio Output
48 kHz
44,1 kHz
English - 98
01392A_HR750_XEU-ENG-0423.indd 98
2007-04-24
9:34:59
UNITED KINGDOM
This Samsung product is warranted for the period of
twelve (12)months from the original date of
purchase,against defective materials and
workmanship.In the event that warranty service is
required,you should return the product to the retailer
from whom it was purchased.
However,Samsung Authorised Dealers and
Authorised Service Centres in other EC Countries
will comply with the warranty on the terms issued to
purchasers in the country concerned.
In case of difficulty,details of our Authorised Service
Centres are available from:
Samsung Electronics U.K. Ltd.
Customer Care Centre
PO Box 17243
Edinburgh, EH11 4YB
United Kingdom
Tel : 0870 SAMSUNG (7267864),
Fax : 0870 7221127 (United Kingdom)
Tel : 0818 717 100,
Fax : +44 (0)870 7221127 (Republic of Ireland)
Web : www.samsung.com/uk
 WARRANTY CONDITIONS
1. The warranty is only valid if,when warranty service
is required,the warranty card is fully and properly
completed and is presented with the original
invoice or sales slip or confirmation, and the serial
number on the product has not been defaced.
2. Samsung ’s obligations are limited to the repair or,
at its discretion,replacement of the product or the
defective part.
3. Warranty repairs must be carried out by
Authorised Samsung Dealers or Authorised
Service Centres. No re-imbursement will be made
for repairs carried out by non Samsung Dealers
and,any such repair work and damage to the
products caused by such repair work will not be
covered by this warranty.
01392A_HR750_XEU-ENG-0423.indd 99
REPUBLIC OF
IRELAND
4. This product is not considered to be defective
in materials nor workmanship by reason that
it requires adaptation in order to conform to
national or local technical or safety standards
in force in any Country other than the one for
which the product was originally designed and
manufactured.This warranty will not cover,and no
re-imbursement will be made for such adaptation
nor any damage which may result.
5. This warranty covers none of the following:
a) Periodic check ups,maintenance and repair or
replacement of parts due to normal wear and
tear.
b) Cost relating to transport,removal or installation
of the product.
c) Misuse,including the faiure to use this product
for its normal purposes or incorrect installation.
d) Damage caused by Lightning,Water,Fire,Acts
of God,Wa ,Public Disturbances,incorrect mains
voltage,improper ventilation or any other cause
beyond the control of Samsung.
6. This warranty is valid for any person who legally
acquired possession of the product during the
warranty period.
7. The consumers statutory rights in any applicable
national legislation whether against the retailer
arising from the purchase contract or otherwise
are not affected by this warranty.Unless there is
national legislation to the contrary,the rights under
this warranty are the consumers sole rights and
Samsung,its subsidiaries and distributors shall not
be liable for indirect or consequential loss or any
damage to records,compact discs,videos or audio
taper or any other related equipment or material.
SAMSUNG ELECTRONICS (U.K.)LTD.
2007-04-24
9:34:59
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care
centre.
Region
01392A_HR750_XEU-ENG-0423.indd 100
Country
Customer Care Centre
Web Site
2007-04-24
9:35:00
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed with other
household wastes at the end of its working life. To prevent possible harm to the environment or human
health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local
government office, for details of where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase
contract. This product should not be mixed with other commercial wastes for disposal.
English
01392A_HR750_XEU-ENG-0423.indd 101
AK68-01392A
2007-04-24
9:35:01
Download PDF