Samsung | DVD-HD945 | Samsung DVD-HD945 User Manual

DVD Player
DVD-HD945
UK
AK68-00422A
Before you start
2. For your safety
* This product utilizes a laser. Use of controls or
adjustments or performance of procedures other than
those specified herein may result in hazardous
radiation exposure.
* Do not open covers and do not repair yourself.
Refer servicing to qualified personal.
3. Caution
* Your player is not intended for industrial use but for
domestic purposes. Use of this product is for
personal use only.
* Do not put any container filled with liquid or any small
metal objects on the player.
* Exterior influences such as lightning and static
electricity can affect normal operation of this player.
If this occurs, turn the player off and on again with the
POWER button, or disconnect and then reconnect the
AC power cord to the AC power outlet. The player will
operate normally.
* When condensation forms inside the player due to
sharp changes in temperature, the player may not
operate correctly. If this occurs, leave the player at
room temperature until the inside of the player
becomes dry and operational.
4. Disc
* Do not clean record-cleaning sprays, benzene,
thinner, or other volatile solvents that may cause
damage to the disc surface.
* Do not touch the disc’s signal surface. Hold by the
edges or by one edge and the hole in the center.
* Wipe the dirt away gently; never wipe a cloth back and
forth over the disc.
CAUTION : USE OF ANY CONTROLS,
ADJUSTMENTS, OR PROCEDURES OTHER THAN
SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
Setup
Accessories
DVD POWER
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Before you start . . . . . . . . . . . . . . . . . . . . . . . .3
General Features . . . . . . . . . . . . . . . . . . . . . . .4
Disc Type and Characteristics . . . . . . . . . . . . .5
Description-Front Panel . . . . . . . . . . . . . . . . . .6
Display Indicators . . . . . . . . . . . . . . . . . . . . . .7
Description-Rear Panel . . . . . . . . . . . . . . . . . .8
Tour of the Remote Control . . . . . . . . . . . . . . .9
TV POWER
PROG
CLEAR
INSTANT
STEP
REPLAY
VOL
TV/VIDEO
SKIP
CH
OPEN/CLOSE
VIDEO SEL.
HDMI SEL.
MENU
INFO
U
MEN
The product unit accompanying this user manual is
licensed under certain intellectual property rights of
certain third parties. This license is limited to private
non-commercial use by end-user consumers for
licensed contents.
No rights are granted for commercial use.
The license does not cover any product unit other than
this product unit and the license does not extend to any
unlicensed product unit or process conforming to
ISO/IEC 11172-3 or ISO/IEC 13818-3 used or sold in
combination with this product unit. The license only
covers the use of this product unit to encode and/or
decode audio files
conforming to the ISO/IEC 11172-3 or ISO/IEC
13818-3. No rights are granted under this license for
product features or functions that do not conform to the
ISO/IEC 11172-3 or ISO/IEC 13818-3.
Table of Contents
DISC
1. Setting up
* Refer to the identification label located on the back
panel of your player for its proper operating voltage.
* Install your player in a cabinet with adequate
ventilation holes. (7~10cm) Do not block ventilation
holes on any of the components for circulation of air.
* Do not push the disc tray by the hand.
* Do not stack components.
* Be sure to turn all components off before moving the
player.
* Before connecting other components to this player, be
sure to turn them off.
* Be sure to remove the disc and turn off the player
after use, especially if you don’t use it for a long time.
RET
URN
Precautions
ZOOM
EZ VIEW
SUBTITLE
AUDIO
ANGLE
NEXT
PRE.
REPEAT
PAGE
INDEX
PRE.
SACD/CD
NEXT
BOOKMARK
Remote Control
Batteries for
Remote Control
(AAA Size)
Connections
Choosing a Connection . . . . . . . . . . . . . . . . .10
Basic Functions
User’s Manual
Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . .14
Using the Search & Skip Functions . . . . . . . .15
Using the Display Function . . . . . . . . . . . . . . .15
Using the Disc and Title Menu . . . . . . . . . . . .16
Using the Function Menu . . . . . . . . . . . . . . . .17
Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . .17
Slow Repeat Play . . . . . . . . . . . . . . . . . . . . . .18
Program Play & Random Play . . . . . . . . . . . .18
Video/Audio Cable
1
Advanced Functions
EZ VIEW
STANDBY/ON
PLAY
Adjusting the Aspect Ratio (EZ View) . . . . . . .19
Selecting the Audio Language . . . . . . . . . . . .20
Selecting the Subtitle Language . . . . . . . . . . .20
Changing the Camera Angle . . . . . . . . . . . . .21
Using the Instant Replay/Skip Function . . . . .21
Using the Bookmark Function . . . . . . . . . . . .22
Using the Zoom Function . . . . . . . . . . . . . . . .23
Super Audio CD Playback . . . . . . . . . . . . . . .23
DVD AUDIO Playback . . . . . . . . . . . . . . . . . .25
Clips Menu for MP3/WMA/JPEG/MPEG4 . . . .26
Folder Selection . . . . . . . . . . . . . . . . . . . . . . .27
MP3/WMA Playback . . . . . . . . . . . . . . . . . . .27
MPEG4 Playback . . . . . . . . . . . . . . . . . . . . . .28
Picture CD Playback . . . . . . . . . . . . . . . . . . .30
LOADING
HDMI - DVI Cable
HDMI Cable
Install Batteries in the Remote
STANDBY/ON
EZ VIEW
PLAY
LOADING
EZ VIEW
STANDBY/ON
2
PLAY
LOADING
3
1. Open the battery cover on the back of the
remote.
2. Insert two AAA batteries. Make sure that the
polarities (+ and -) are aligned correctly.
3. Replace the battery cover.
Changing Setup menu
Using the Setup Menu . . . . . . . . . . . . . . . . . .31
Setting Up the Language Features . . . . . . . . .31
Setting Up the Audio Options . . . . . . . . . . . . .33
Surround Sound Speaker Setup . . . . . . . . . . .34
Setting Up the Display Options . . . . . . . . . . . .35
Setting Up the Parental Control . . . . . . . . . . .37
If remote doesn’t operate properly
STANDBY/ON
4
5
EZ VIEW
PLAY
LOADING
• Check the polarity + - of the batteries (Dry-Cell)
• Check if the batteries are drained.
• Check if remote sensor is blocked by obstacles.
• Check if there is any fluorescent lighting nearby.
Reference
5. Environmental info
* The battery used in this product contains chemicals
that are harmful to the environment.
* So, dispose of batteries in the proper manner,
according to federal, state, and local regulations.
Controlling a TV with the Remote . . . . . . . . . .39
Firmware upgrade . . . . . . . . . . . . . . . . . . . . .40
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . .41
Specifications . . . . . . . . . . . . . . . . . . . . . . . .43
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
ENG-2
ENG-3
General Features
Disc Type and Characteristics
Excellent Sound
MPEG4
Dolby Digital, a technology developed by Dolby
Laboratories, provides crystal clear sound
reproduction.
This unit can play MPEG4 formats within an avi file.
Screen
Video with MPEG-2 compression technology.
Both regular and widescreen(16:9) pictures can be
viewed.
DVD AUDIO
DVD AUDIO is a format specifically designed to
provide the highest possible audio fidelity capable
on DVD.
An important scene can be viewed in slow motion.
Programmed Play (CD)
Note
You can program tracks to play in desired order.
* Discs which cannot be played with this player.
• DVD-ROM
• DVD-RAM
• CD-ROM
• CDV
• CDI
• CVD
• CDGs play audio only, not graphics.
Parental Control (DVD)
The parental control allows users to set the level
necessary to prohibit children from viewing harmful
movies such as those with violence, adult subject
matter, etc.
Various On-Screen Menu Functions
You can select various languages (Audio/Subtitle)
and screen angles while enjoying movies.
EZ VIEW (DVD)
Easy View can convert Letter Box images to full
screen viewing on your conventional TV.
Digital Photo Viewer (JPEG)
You can view Digital Photos on your TV.
Repeat
You can repeat a song or movie simply by pressing
the REPEAT button.
MP3/WMA
This unit can play discs created from MP3/WMA
files.
Instant Replay (DVD)
This function is used to replay the previous
10 seconds of a movie from the current position.
Instant Skip (DVD)
This function skips playback ahead 10 seconds.
Disc Types (Logos)
Recording Types
DVD-VIDEO
Audio
+
Video
HDMI (High Definition Multimedia Interface)
HDMI reduces picture noise by allowing a pure
digital video/audio signal path from the player to
your TV.
Slow Motion
This DVD player is capable of playing the following types of discs with the corresponding logos:
* Ability to play back may depend on recording
conditions.
• DVD-R, +R
• CD-RW
• DVD+RW, -RW
* The unit may not play certain CD-R, CD-RW and
DVD-R due to the disc type or recording
conditions.
VIDEO-CD
Audio
+
Video
AUDIO-CD
Disc Size
12 Cm
8 Cm
Max. Playing Time
Single-sided 240 min. • DVD contains excellent sound and
Double-sided 480 min. video due to Dolby Digital and
MPEG-2 system.
•
Various
screen and audio functions
Single-sided 80 min.
can be easily selected through the
Double-sided 160 min.
on-screen menu.
12 Cm
74 min.
8 Cm
20 min.
12 Cm
74 min.
8 Cm
20 min.
Audio
DVD AUDIO
12 Cm
400 min.
Audio
12 Cm
74 min.
• Super Audio CD is a high quality audio
format with higher sampling rates and fuller,
richer sound as compared to regular CD.
This product incorporates copyright protection
technology that is protected by methods claims of
certain U.S. patents and other intellectual property
rights owned by Macrovision Corporation and other
rights owners. Use of this copyright protection
technology must be authorized by Macrovision
Corporation, and is intended for home and other
limited viewing uses only unless otherwise
authorized by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.
Disc Markings
PAL
Play Region Number
Play Region Number
Both the DVD player and the discs are coded by region.
These regional codes must match in order for the disc to
play. If the codes do not match, the disc will not play.
PAL broadcast system in U.K, France,
Germany, etc.
The Region Number for this player is described on the
rear panel of the player.
Dolby Digital disc
STEREO
DIGITAL
SOUND
DivX Certification
Stereo disc
Digital Audio disc
DTS disc
DivX, DivX Certified, and
associated logos are
trademarks of DivXNetworks, Inc and
are used under license.
MP3 disc
Super Audio CD
Super Audio CD is a high quality audio format with
higher sampling rates and fuller, richer sound as
compared to regular CD.
Super Audio CD disc
DVD AUDIO disc
ENG-4
• CD is recorded as a Digital Signal
with better audio quality, less
distortion and less deterioration of
audio quality over time.
• DVD AUDIO is a format specifically
designed to provide the highest
possible audio fidelity capable on
DVD.
Super Audio CD
~
• Video with CD sound, VHS
quality & MPEG-1 compression
technology.
Audio
+
Video
COPY PROTECTION
Many DVD discs are encoded with copy
protection. Because of this, you should only
connect your DVD player directly to your TV, not
to a VCR. Connecting to a VCR results in a
distorted picture from copy-protected DVD
discs.
Characteristics
ENG-5
Description-Front Panel
Display Indicators
6
3
7
6
7
8
9
10 11 12 13 14 15 16 17
1
STANDBY
2
1
2
3
4
5
8
4
9
5
Front Panel Controls
Front Panel Display
1. STANDBY/ON (
)
• When the unit is first plugged in, the red indicator lights.
When STANDBY/ON button is pressed on, the blue light appears and the player is turned on.
1. DVD : DVD is loaded
Audio : DVD-Audio disc is playing
2. DISC TRAY
• Place the disc here.
18
2. Super Audio CD is loaded
3. DTS (Digital Theater System) output
4. Dolby-Digital Disc
3. OPEN/CLOSE (
)
• Press to open and close the disc tray.
5. Progressive Scan Video output
4. DISPLAY
• Operation indicators are displayed here.
6. DVD-Audio : Group number
5. STOP (
)
• Stops disc play.
8. DVD-Audio, CD, Video CD, Super Audio CD : Track number
7. DVD-Video : Title number
6. SKIP (
) / SEARCH
• Use to reverse skip a scene or music.
9. DVD-Video : Chapter number
7. PLAY/PAUSE (
)
• Begin or pause disc play.
11. Disc type indicators : SVCD, VCD, CD
10. DVD-Audio : Index number
12. MPEG Audio output
8. REMOCON RECEIVER
13. CVD Disc indicator
9. SKIP (
) / SEARCH
• Use to forward skip a scene or music.
14. MP3 Audio output
15. Linear PCM audio output
16. Lights when the device connected to the HDMI Jack is a DVI device
17. Lights when the device connected to the HDMI Jack is a HDMI device
18. Displays various messages concerning operations such as PLAY, STOP, LOAD ...
no DISC : No disc loaded.
OPEN : The disc tray is open.
LOAD : Player is loading disc information.
ENG-6
ENG-7
Description-Rear Panel
1
Tour of the Remote Control
This remote control can also control most TVs. See page 39.
7
DVD POWER
TV POWER
18
1
2
3
CLEAR
PROG
INSTANT
4
5
6
2
3
4
5
6
8
Rear Panel
TV/VIDEO
SKIP
REPLAY
VOL
CH
OPEN/CLOSE
VIDEO SEL.
HDMI SEL.
7
24
8
7. COMPONENT OUT JACKS
• Use these jacks if you have a TV with
Component Video in jacks. These jacks provide
Pr, Pb and Y video.
• If Component (Pscan) & HDMI Video Output is
selected in Setup Menu, interlaced scan mode
and Video, S-Video will not work.
• If Component (Iscan) Video Output is selected
in Setup Menu, progressive scan and HDMI
mode will not work.
2. 5.1CH ANALOG AUDIO OUT JACKS
• Connect to an amplifier with 5.1ch analog input
jacks.
3. AUDIO OUT JACKS
• Connect to the Audio input jacks of your
television, audio/video receiver.
8. SCART JACK
• Connect to a TV scart input jack.
4. VIDEO OUT JACK
• Use a video cable to connect to the Video input
jack on your television.
• The Video Output in Setup Menu must be set to
Component (Iscan), SCART Output or
S-Video.
Important Note
5. S-VIDEO OUT JACK
• Use the S-Video cable to connect this jack to
the S-Video jack on your television for a higher
quality picture.
• The Video Output in Setup Menu must be set to
S-Video.
• If Component(Pscan) & HDMI Video Output is
selected in Setup Menu, Video and S-Video,
SCART will not work.
• Consult your TV User’s Manual to find out if your
TV supports Progressive Scan. If Progressive
Scan is supported, follow the TV User’s Manual’s
instructions regarding Progressive Scan settings in
the TV’s menu system.
• The HDMI output of this unit can be connected to
a DVI jack on a TV or other device using a conversion adapter. In this case, it is necessary to use a
TV or display with an HDCP-compatible DVI input.
6. HDMI OUT JACK
• Use the HDMI or HDMI-DVI cable to connect
this jack to the HDMI or DVI jack on your
television for the best quality picture.
• If HDMI cable is connected with TV available for
HDMI output, HDMI mode will work
automatically.
• There may be no image output if connected to a
TV or display that is not compatible with the above
format.
• Refer to the instruction manual of the TV or display
to be connected to this unit for detailed information
regarding the HDMI terminal.
• See page 36 to get more information on how to
use the setup menu.
ENG-8
9
10
11
MENU
INFO
U
EN
CM
DIS
1. DIGITAL AUDIO OUT JACKS
• Use an optical or coaxial digital cable to connect
to a compatible Dolby Digital receiver.
Use to connect to an A/V Amplifier that contains
a Dolby Digital or DTS decoder.
RET
UR
N
1
STEP
19
20
21
22
23
25
26
27
28
29
ZOOM
12
13
14
EZ VIEW
SUBTITLE
AUDIO
ANGLE
NEXT
PRE.
PRE.
SACD/CD
30
31
32
PAGE
INDEX
15
16
REPEAT
NEXT
BOOKMARK
17
DVD Function Buttons
1. DVD POWER Button
• Turns the power on or off.
2. NUMBER Buttons
3. PROG Button
• Allows you to program a specific order.
4. STEP Button
• Advances play one frame at a time.
5. VOL +/- Buttons
• Control volumes.
6. TV/VIDEO Button
• Press to display all of the available video sources
( i.e., TV, Cable, Video)
7. VIDEO SEL. Button
• Selects Video output format.
33
34
35
8. SEARCH Buttons (
/
)
• Allow you to search forward/backward through a disc.
9. STOP Button (
)
10. MENU Button
• Brings up the DVD player’s menu.
11. RETURN Button
• Returns to a previous menu.
12. ZOOM Button
• Enlarges DVD picture.
13. AUDIO Button
• Use this button to access various audio functions on a disc.
14. SUBTITLE Button
15. INDEX Buttons
• Use to skip the INDEX.
16. SACD/CD Button
• Selects Super Audio CD or CD playback mode.
17. SHUTTLE DIAL (Search mode)
• Performs fast motion play.
18. TV POWER button
• Turns the TV’s power on or off.
19. CLEAR Button
• Use to remove menus or status displays from the screen.
20. INSTANT SKIP Button
• This function skips playback ahead 10 seconds.
21. INSTANT REPLAY Button
• This function is used to replay the previous 10
seconds of a movie from the current position.
22. CH / Buttons
• Channel selection.
23. OPEN/CLOSE ( ) Button
• To open and close the disc tray.
24. HDMI SEL. Button
• HDMI or DVI Output resolution setup.
25. SKIP Buttons (
/
)
• Use to skip the title, chapter, or track.
26. PLAY/PAUSE Button (
)
• Begin/Pause disc play.
27. INFO Button
• Displays the current disc mode.
28. DISC MENU Button
• Brings up the Disc menu.
29. ENTER/DIRECTION Button
(UP/DOWN or LEFT/RIGHT Buttons)
• This button functions as a toggle switch.
30. EZ VIEW Button
• Easy View can convert Letter Box images to full
screen viewing on your conventional TV.
31. ANGLE Button
• Use to access various camera angles on a DVD.
32. REPEAT Button
• Allows you to repeat play a title, chapter, track, or disc.
33. PAGE Buttons
• Use to skip the PAGE.
34. BOOKMARK Button
35. JOG DIAL (Step mode)
• Operates frame by frame play. In CD mode, performs
track search.
ENG-9
Choosing a Connection
Choosing a Connection
The following shows examples of connections commonly used to connect the DVD player with a TV
and other components.
Connection to a TV (For Video)
TV (Normal, Widescreen, Projection, etc..)
Before Connecting the DVD Player
• Always turn off the DVD player, TV, and other components before you connect or disconnect any cables.
Method 1
Method 2
Method 3
Video
S-Video
SCART Jack
Basic Audio
Method 4
Interlace scan
• If you connected an external Audio System, turn on your Audio System and set it to the correct Audio Input.
• Refer to the owner’s manual of the additional components you are connecting for more information on those
particular components.
TV
Connection to an Audio System
AV
Cable
Method 1
Method 2
S-Video
Cable
Method 3
OR
AUDIO
SYSTEM
Scart
Cables
(not
supplied)
Video
Cables
OR
OR
DVD
Player
2ch Amplifier
5.1ch Analog Amplifier
Dolby Digital Decoder
Audio Input Jacks
Audio Input Jacks
Digital Audio Input Jack
Audio Output
Jacks
Video Output
Jack
S-Video Jack
SCART Jack
Component Jacks
1. Connect a cable with the desired method.
2. Turn on your TV and DVD Player.
3. Set your TV the correct video input by pressing TV/VIDEO button on. (See page 39)
4. Select the video output according to the cable connection.
If you use the VIDEO SEL. button, you can change easily video output in no disc mode.
OR
DVD
Player
Method 1
DVD Player + TV with Video Input Jack
(The Video Output in Setup Menu must be set to S-Video, SCART or Component (Iscan).)
Method 2
DVD Player + TV with S-Video Input Jack
(The Video Output in Setup Menu must be set to S-Video.)
Audio Output Jaks
(2 Channel)
5.1CH Analog Audio Output Jacks
(Multi Channel)
Digital Audio Output Jack
Method 3
DVD Player + TV with Scart Input Jacks (Audio & Video)
(The Video Output in Setup Menu must be set to SCART Output.)
Method 4
DVD Player + TV with Component Video Jacks
(The Video Output in Setup Menu must be set to Component (Iscan).)
Note
• DVD-AUDIO only plays back two channel audio through the Digital Audio out. Multi-channel DVD-Audio discs
are output through the Analog outputs.
• Super Audio CD plays back only through the Analog outputs. (See page 33~34)
Note
• If you press the VIDEO SEL. button, Video output mode is changed in regular sequence in no disc mode.
(S-Video ➝ Iscan ➝ Pscan & HDMI ➝ SCART RGB ➝ SCART Video)
ENG-10
ENG-11
Choosing a Connection
Choosing a Connection
Connection to a TV (For Progressive scan, Digital Video)
Method 2
Method 1
Progressive scan
HDMI VIDEO Specifications
Basic Audio
Digital Video
DVI Audio Input
Method 3
HDMI Input
TV
When you press the HDMI SEL. button, in case of PAL TV system 576p, 720p, 768p, 1080i are selected in order.
When you press the HDMI SEL. button, in case of NTSC TV system 480p, 720p, 768p, 1080i are selected in
order.
The first press of the HDMI SEL. button, brings up the current resolution.
The second press allows you to change the HDMI output resolution.
* The specific resolution of HDMI output may not work depending on your TV.
* Refer to the TV users manual.
Important Note
• HDMI (High Defintion Multimedia Interface)
HDMI is an interface to enable the digital transmission of video and audio data with just a single connector.
Using HDMI, the DVD player transmits a digital video and audio signal and displays a vivid picture on a TV
having a HDMI jack.
• Description of the HDMI connection
HDMI connector - Both uncompressed video data and digital audio data(LPCM or Bit Stream data).
• Though the player uses a HDMI cable, the player outputs only a pure digital signal to the TV.
• If TV does not support HDCP (High-bandwidth Digital content protection), snow noise appears on the screen.
DVD
Player
Component Jacks
Audio Output Jacks
HDMI Output Jack
Audio Output Jacks
HDMI Output Jack
Method 1
DVD Player + TV with Component Video Jacks.
(The Video Output in Setup Menu must be set to Component (Pscan) & HDMI.)
Method 2
DVD Player + TV with DVI Jack.
• Depending on your TV, your hookup for Method 2 may differ from the illustration.
(The Video Input on TV must be set to DVI.)
Method 3
DVD Player + TV with HDMI Jack.
• Depending on your TV, your hookup for Method 3 may differ from the illustration.
(The Video Input on TV must be set to HDMI.)
Important Note
• Consult your TV User’s Manual to find out if your TV supports Progressive Scan, DVI or HDMI.
If Progressive Scan, HDMI is supported, follow the TV User’s Manual’s instructions regarding Progressive
Scan, HDMI settings in the TV’s menu system.
• When the Video output is Pscan & HDMI Video and S-Video, SCART will not work.
• If you want to convert Video Output to Progressive Scan, select Component (Pscan) & HDMI in SETUP menu
and then select “Yes” within 10 seconds. Finally change the TV's external input to Component(576p/480p). (See
Page 36)
• Use the VIDEO SEL. button to easily change the video output in no disc mode. (See page 11)
• If HDMI or HDMI-DVI cable is pluged in TV, the player output is Pscan & HDMI out automatically.
• Refer to your TV user's manual.
ENG-12
• Why does Samsung use HDMI?
Analog TVs require an analog video/audio signal. However, when playing a DVD, the data transmitted to a TV is
digital. Therefore either a digital-to-analog converter(in the dvd player) or an analog-to-digital converter (in the
TV) is required. During this conversion, the picture quality is degraded due to noise and signal loss.
DVI technology is superior because it requires no D/A conversion and is a pure digital signal from the player to
your TV.
• What is the HDCP?
HDCP(High-bandwidth Digital Content Protection) is a system for protecting DVD content outputted via DVI
from being copied. It provides a secure digital link between a video source(PC, DVD. etc) and a display
device(TV, projector . etc). Content is encrypted at the source device to prevent unauthorized copies from being
made.
PROGRESSIVE SCAN OUTPUT (525p/625p)
“CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINITION TELEVISION SETS ARE
FULLY COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS TO BE
DISPLAYED IN THE PICTURE, IN CASE OF 525 OR 625 PROGRESSIVE SCAN PICTURE
PROBLEMS, IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION TO THE
‘STANDARD DEFINITION’ OUTPUT. IF THERE ARE QUESTIONS REGARDING OUR TV
SET COMPATIBILITY WITH THIS MODEL 525p AND 625p DVD PLAYER, PLEASE
CONTACT OUR CUSTOMER SERVICE CENTER.”
ENG-13
Playing a Disc
Before Play
• Turn on your TV and set it to the correct Video
Input by pressing TV/VIDEO button on the TV
remote control.
• If you connected an external Audio System, turn
on your Audio System and set it to the correct
Audio Input.
After plugging in the player, the first time you press
the DVD POWER button, this screen comes up :
If you want to select a language, press a
NUMBER button. (This screen will only appear
when you plug in the player for the first time.)
If the language for the startup screen is not set,
the settings may change whenever you turn the
power on or off. Therefore, make sure that you
select the language you want to use.
Using the Search & Skip Functions
7. Step Motion Play
(Except CD/DVD-AUDIO/Super Audio CD)
Turn the Jog dial clockwise or press the STEP button on
the remote during play.
- Each time the button is pressed or Jog Dial is turned, a
new frame will appear.
- No sound is heard during STEP mode.
- Press PLAY/PAUSE (
) button to resume normal
play.
- You can only perform step motion play in the forward
direction.
8. Slow Motion Play
(Except CD/DVD-AUDIO/Super Audio CD)
Press the FWD SEARCH (
) button on the remote
during PAUSE or STEP mode.
- By pressing the FWD SEARCH (
) button, you can
select slow motion play for 1/8, 1/4 or 1/2 of normal
speed.
- No sound is heard during slow mode.
- Press PLAY/PAUSE (
) to resume normal play.
- Reverse slow motion play will not work.
During play, you can search quickly through a
chapter or track or use the skip function to
jump to the next selection.
Searching through a Chapter or Track
During play, press the SERACH (
or
) button
and press again to search at a faster speed.
• You can also use the Shuttle dial on the remote by
turning.
- Forward Shuttle dial :
1/8 ➝
2X ➝
1/4 ➝
4X ➝
- Reverse Shuttle dial :
2X ➝
4X ➝
1/2 ➝ Play ➝
8X
Using the Display Function
When Playing a DVD/VCD/CD
1. During play, press the INFO button on the remote.
2. Use the UP/DOWN buttons to select the desired
item.
3. Use the LEFT/RIGHT buttons to make the
desired setup and then press ENTER.
• You may use the number buttons of the remote
control to directly access a title, chapter or to
start the playback from the desired time.
4. To make the screen disappear, press the INFO
button again.
8X
• In case of Super Audio CD, when the clips menu is off,
you can use this function. (See page 24)
DVD
DVD
2X, 4X, 64X, 128X
VCD
CD/Super Audio
CD/DVD-AUDIO
4X, 8X
DVD
2X, 4X, 8X
Chapter 02
Title
Time
Audio
Subtitle
RESUME function
When you stop disc play, the player remembers
where you stopped, so when you press
PLAY/PAUSE (
) button again, it will pick up
where you left off. (unless the disc is removed or the
player is unplugged, or if you press the STOP (
)
button twice.)
Play
2. Place a disc gently into the tray with the disc’s
label facing up.
3. Press the PLAY/PAUSE (
) button or
OPEN/CLOSE button to close the disc tray.
4. Stopping Play
Press the STOP (
) button during play.
5. Removing Disc
0:00:13
ENG 5.1CH
Off
Skipping Tracks
During play, press the
or
button.
• When playing a DVD, if you press the
button, it
moves to the next chapter. If you press the
button, it
moves to the beginning of the chapter. One more press
makes it move to the beginning of the previous chapter.
VCD
VCD
Track 01
Time 0 : 0 0 : 4 8
1. Press the OPEN/CLOSE button.
The STANDBY indicator light goes out and the tray
opens.
01
Note
• If the player is left for about 5 minutes in pause
mode, it will stop.
• If the player is left in the stop mode for more than
about 30 minutes, the power will automatically shut
off. (Automatic Power-Off Function)
• If the player is left in the stop mode for more than
one minute without any user interaction, a screen
saver will be activated. Press the PLAY/PAUSE
(
) button to resume normal play.
• This
icon indicates an invalid button press.
• When playing a VCD 2.0 in Menu Off mode, a VCD 1.1,
Super Audio CD, DVD-AUDIO or a CD, if you press the
button, it moves to the next track.
If you press the
button, it moves to the beginning of
the track. One more press makes it move to the beginning
of the previous track.
CD
• If a track exceeds 15 minutes when playing a VCD and
you press the
button, it moves forward 5 minutes, in
menu off mode. If you press the
button, it moves
backward 5 minutes.
CD
Track 01
Time 0 : 0 0 : 4 8
Press the OPEN/CLOSE button.
Note
• When playing a VCD 2.0, you can choose Menu
On or Menu Off by using the DISC MENU
button.
6. Pausing Play
Press the PLAY/PAUSE (
) or STEP button on the
remote during play.
- Screen stops, no sound.
- To resume, press the PLAY/PAUSE (
) button once
again.
ENG-14
ENG-15
Using the Display Function
To access the desired title when there is
Title more than one in the disc.
For example, if there is more than one
movie on a DVD, each movie will be
identified.
Using the Disc and Title Menu
Using the Disc Menu
Using the Function Menu
1. During the playback of a DVD disc, press the
MENU button on the remote.
1. Press the MENU button during playback.
2. Select Disc Menu using the UP/DOWN buttons,
then press the RIGHT or ENTER button.
Most DVD discs are recorded in
Chapter chapters so that you can quickly find a
specific passage (similar to tracks on an
audio CD).
Allows playback of the film from a
time as a reference.
Refers to the language of the film
Audio soundtrack. In the example, the
Refers to the subtitle languages
Subtitle available in the disc.
You will be able to choose the subtitle
languages or, if you prefer, turn them off
from the screen.
A DVD disc can have up to 32 different
subtitles.
2. Use the UP/DOWN buttons to highlight Function,
then press the RIGHT or ENTER button.
3. Function selection screen appears: Info, Zoom,
Bookmark, Repeat, EZ View and Front Display.
-
Time desired time. You must enter the starting
soundtrack is played in English 5.1CH.
A DVD disc can have up to eight
different soundtracks.
Using the Function Menu
Using the Title Menu
Info (See Page 15~16)
Zoom (See Page 23)
Bookmark (See Page 22)
Repeat (See Page 17)
EZ View (See Page 19)
Front Display : On
On : Lights when the front display is selected ON.
Repeat Play
Repeat the current track, chapter, title, a
chosen section (A-B), or all of the disc.
1. Press the REPEAT button on the remote.
Repeat screen appears.
2. Select Chapter, Title or A-B using the
LEFT/RIGHT buttons.
• Chapter ( ) : repeats the chapter that is playing.
• Title ( T ) : repeats the title that is playing.
• A-B : repeats a segment of the disc that you select.
* A-B REPEAT
• Press ENTER at the point where you want the repeat
play to start (A).
• Press ENTER at the point where you want the repeat
play to stop (B).
• To terminate the function, press the 'CLEAR' button.
• A-B REPEAT does not allow you to set point (B) until at
least 5 seconds has elapsed after point (A) has been
set.
4. Use the UP/DOWN button to highlight one of the
6 functions. Then press the RIGHT or ENTER
button to access the function.
1. During the playback of a DVD disc, press the
MENU button on the remote.
DVD
2. Select Title Menu using the UP/DOWN buttons,
then press the RIGHT or ENTER button.
Off
01
T
01 A - B
REPEAT
ENTER
01
D
01 A - B
REPEAT
ENTER
VCD/CD
Note
• You can also directly select these functions using
their respective buttons on the remote.
Note
• When VCD 2.0 is in Menu Off mode only, this
function works. (See page 15)
Off
T
3. Press ENTER.
Note
• Depending on a disc, the Title and Disc Menus
may not work.
• Title Menu will only be displayed if there are at
least two titles in the disc.
• You can also use the Disc Menu, using the DISC
MENU button on the remote.
• In VCD 2.0, the DISC MENU button is used to
select Menu On or Menu Off mode.
ENG-16
4. To return to normal play, press REPEAT again,
then press the LEFT/RIGHT buttons to select Off
and press ENTER.
Note
• DVD repeats play by chapter or title, CD and VCD
repeat play by disc or track.
• Depending on a disc, the Repeat function may not
work.
• When VCD 2.0 is in Menu Off mode only, this
function works. (See page 15)
ENG-17
Slow Repeat Play
Program Play & Random Play
Adjusting the Aspect Ratio (EZ View)
This feature allows you to slowly repeat
scenes containing sports, dancing, musical
instruments being played etc. so you can
study them more closely.
Program Play (CD)
To play back using aspect ratio (DVD)
If you are using a 4:3 TV
1. Press the PROG button.
1. For 16:9 aspect ratio discs
When playing a DVD/VCD
3. Use the LEFT/RIGHT/UP/DOWN buttons to select
the first track to add to the program.
Press the ENTER button. The selection numbers
appear in the Program Order box.
Press the EZ VIEW button.
• The screen size changes when the button is
pressed repeatedly.
• The screen zoom mode operates differently
depending on a screen setting in the initial setup
menu.
• To ensure correct operation of the EZ VIEW
button, you should set the correct aspect ratio in
the initial setup (See page 35).
1. During play, press the PLAY/PAUSE (
button.
)
2. Press the FWD SEARCH (
) button on the
remote during PAUSE or STEP mode.
3. Press the REPEAT button on the remote.
Repeat screen appears.
2. Use the LEFT/RIGHT buttons to select
PROGRAM. Press the ENTER button.
4. Press the PLAY/PAUSE (
) button.
The disc will be played in programmed order.
PROGRAM
• 4:3 Pan Scan
The left and right of the screen are cut off and
displays the central portion of the 16:9 screen.
• Screen Fit
The top and bottom of the screen are cut off
and the full screen appears.
The picture will look vertically stretched.
If you are using a 16:9 TV
1. For 16:9 aspect ratio discs
RANDOM
4. Select A-B using the LEFT/RIGHT buttons.
• Wide Screen
5. Press ENTER at the point where you want the
repeat play to start (A).
• Zoom Fit
The top, bottom, left and right of the screen are
cut off and the central portion of the screen is
enlarged.
Displays the content of the DVD title in 16:9
aspect ratio.
• A-B REPEAT does not allow you to set point (B) until at
least 5 seconds has elapsed after point (A) has been
set.
PROGRAM 01
Program Order
Track
01
05
09
13
6. Press ENTER at the point where you want repeat
play to stop (B).
02
06
10
14
03
07
11
15
04
08
12
16
-----
7. To return to normal play, press the CLEAR button
and then press the PLAY/PAUSE (
) button.
Note
• The disc will play from A to B repeatedly at the
speed you chose.
• When VCD 2.0 is in Menu Off mode only, this
function works. (See page 15)
• 4:3 Letter Box
Displays the content of the DVD title in 16:9
aspect ratio. The black bars will appear at the
top and bottom of the screen.
------
------
------
CLEAR
Random Play (CD)
1. Press the PROG button.
2. Use the LEFT/RIGHT buttons to select RANDOM.
Press the ENTER button.
PROGRAM
RANDOM
• Screen Fit
The top and bottom of the screen are cut off.
When playing a 2.35:1 aspect ratio disc, the
black bars at the top and bottom of the screen
will disappear. The picture will look vertically
stretched. (Depending on a type of disc, the
black bars may not disappear completely.)
ENG-18
• Normal Screen
Displays the content of the DVD title in 4:3
aspect ratio.
• Screen Fit
The top and bottom of the screen are cut off
and the full screen appears.
The picture would look vertically stretched.
• Zoom Fit
The top, bottom, left and right of the screen are
cut off and the central portion of the screen is
enlarged.
• Zoom Fit
The top, bottom, left and right of the screen are
cut off and the central portion of the screen is
enlarged.
2. For 4:3 aspect ratio discs
• Normal Wide
Displays the content of the DVD title in 16:9
aspect ratio. The picture will look horizontally
stretched.
• Screen Fit
The top and bottom of the screen are cut off
and the full screen appears.
The picture will look vertically stretched.
Note
• Depending on a disc, the Program and Random
Play functions may not work.
• This unit can support a maximum of 20
programmed tracks.
• While in playback mode, press the CLEAR button
on the remote control to cancel Programmed Play
or Random Play.
2. For 4:3 aspect ratio discs
Note
• This function may behave differently depending on
a type of disc.
• Zoom Fit
The top, bottom, left and right of the screen are
cut off and the central portion of the screen is
enlarged.
• Vertical Fit
When a 4:3 DVD is viewed on a 16:9 TV, black
bars will appear at the left and right of the
screen in order to prevent the picture from
looking horizontally stretched.
ENG-19
Selecting the Audio Language
Selecting the Subtitle Language
You can select a desired audio quickly and
easily with the AUDIO button.
You can select a desired subtitle quickly and
easily with the SUBTITLE button.
Using the AUDIO button
Using the SUBTITLE button
1. Press the AUDIO button.
1. Press the SUBTITLE button.
- The subtitle languages are represented by
abbreviations.
2. The Audio changes when the button is pressed
repeatedly.
The audio languages are represented by abbreviations.
DVD
2. The subtitle changes when the button is pressed
repeatedly.
DVD
ENG DOLBY DIGITAL 5.1CH
AUDIO
Off
Using the Instant Replay/Skip Function
When a DVD contains multiple angles of a
particular scene, you can use the ANGLE
function.
Using the Instant Replay function (DVD)
Using the ANGLE button
If you press the INSTANT REPLAY button, the
current scene moves backward about 10 seconds,
and plays back.
If the disc contains multiple angles, the ANGLE
mark appears on the screen.
1. Press the ANGLE button, then ANGLE icon will
appear with the current angle number and the
number of angles available.
If you miss a scene, you can see it again using
this function.
* Depending on a disc, the Instant Replay function may not
work.
2. Press the ANGLE button repeatedly to the
desired angle.
3. To remove the ANGLE icon, press the CLEAR or
RETURN button.
- In case of a VCD or CD, you can select among Stereo,
Right or Left.
- Use the LEFT/RIGHT buttons to select the desired
subtitle language on a MPEG4 then press the ENTER.
VCD/CD
Stereo
SUBTITLE
Changing the Camera Angle
4/6
ANGLE
MPEG4
AUDIO
Using the Instant Skip function (DVD)
None
Use this function to skip playback about 10
seconds ahead of the current scene.
- Use the LEFT/RIGHT buttons to select the desired
Audio on a MPEG4 then press the ENTER.
MPEG4
3. To remove the AUDIO icon, press the CLEAR or
RETURN button.
Note
• This function depends on what audios are
encoded on the disc and may not work.
• A DVD disc can contain up to 8 audio languages.
• How to have the same audio language come up
whenever you play a DVD;
Refer to “Setting Up the Language Features” on
page 32.
Press the INSTANT SKIP button.
3. To remove the SUBTITLE icon, press the CLEAR
or RETURN button.
Note
• If the disc has only one angle, this feature won’t
work. Currently, very few discs have this feature.
- Playback will skip ahead 10 seconds.
- Depending on a disc, this function may not work.
Note
• This function depends on what subtitles are
encoded on the disc and may not work.
• A DVD disc can contain up to 32 subtitle
languages.
• How to have the same subtitle language come
up whenever you play a DVD;
Refer to “Setting Up the Language Features” on
page 33.
ENG-20
ENG-21
Using the Bookmark Function
This feature lets you bookmark sections of a
DVD or VCD (Menu Off mode) so you can
quickly find them at a later time.
Using the Bookmark Function (DVD/VCD)
1. During play, press the BOOKMARK button on the
remote.
2. Use the LEFT/RIGHT buttons to move to the
desired bookmark icon.
Using the Zoom Function
Super Audio CD Playback
Recalling a Marked Scene
Using the Zoom Function (DVD/VCD)
1. Open the disc tray.
1. During play, press the BOOKMARK button on the
remote.
1. During play or pause mode, press the ZOOM
button on the remote.
A Zoom mark will be displayed on screen.
2. Place the Super Audio CD disc on the tray.
- Place the Super Audio CD disc with the labeled
side up.
2. Use the UP/DOWN or LEFT/RIGHT buttons to
select the part of the screen you want to zoom in
on.
3. Close the tray.
- The tray closes and you should get a screen
that looks like the one below.
2. Use the LEFT/RIGHT buttons to select a marked
scene.
3. Press the PLAY/PAUSE (
the marked scene.
) buttons to skip to
3. Press the ENTER button.
- During DVD play, press ENTER to zoom in
2X/4X/2X/Normal in order.
- During VCD play, press ENTER to zoom in 2X/Normal
in order.
3. When you reach the scene you want to mark,
press the ENTER button. The icon will change to
a number (1, 2, or 3).
4. Press the BOOKMARK button to turn Off the
display.
Clearing a Bookmark
1. During play, press the BOOKMARK button on the
remote.
Super Audio CD Clips Menu On Play
Function
2. Use the LEFT/RIGHT buttons to select the
bookmark number you want to delete.
1. Use the UP/DOWN buttons to select a music title.
3. Press the CLEAR button to delete a bookmark
number. Press the BOOKMARK button to turn Off
the display.
Note
• Up to three scenes may be marked at a time.
• When VCD 2.0 is in Menu Off mode only, this
function works. (See page 15)
• Depending on a disc, the Bookmark function may
not work.
ENG-22
2. Press the ENTER button to begin playback of the
music title.
- If you want to use the Repeat Function, press the
REPEAT button to change the mode, such as Off,
Track, Disc.
*Off : Normal Playback
*Track : Repeats the current music title.
*Disc : Repeats the music titles in the Super
Audio CD.
- If you want to see information about the Disc title
and Artist, press the INFO button.
- If you want to convert into regular CD mode,
press the SACD/CD button.
- During play or stop mode, you can change the
2CH or MULTI mode by using LEFT/RIGHT
buttons. (You can use this function when Super
Audio CD disc includes multi channel and 2
channel audio format.)
ENG-23
Super Audio CD Playback
Super Audio CD Clips Menu Off Play
Function
1. In Stop mode, press the DISC MENU button until
the Clips menu is off.
2. During playback, press the INFO button and the
screen below appears.
SuperAUDIO
DVD
AudioPlayback
CD Playback
CD Layer Play Function
1. Open the disc tray.
During Super Audio CD playback, press the
SACD/CD button to playback the CD layer of a dual
layer Super Audio CD disc. (Refer to the page 15 for
setting CD playback Function).
2. Place the DVD AUDIO disc on the tray.
- Place the DVD AUDIO disc with the labeled side up.
Most DVD AUDIO discs are recorded in
Group, you can change Groups with this
Function.
1. During play, press the INFO button on the remote.
Note
* Bonus Group playback.
• Some DVD AUDIO discs have Bonus
groups. If you want to play a Bonus
group, you must enter the Bonus
Group code. The code is usually on the
DVD AUDIO disc case.
2. Use the UP/DOWN buttons to select the desired
item.
To access the desired Track when there is
more than one on the DVD AUDIO disc.
3. Use the LEFT/RIGHT buttons to make the
desired setup and then press ENTER.
• You may use the number buttons of the remote
control to directly access a Group, Track, Page
or to start the playback from the desired time.
If pages are included with the
DVD-AUDIO, you can see this icon.
To access the desired page, you can
use this Function.
3. Close the tray.
- The tray closes and disc plays.
CD
3. Use the UP/DOWN buttons to select the desired
item.
Track 01
Time
0 : 00: 13
Using the Display Function
SACD
Track 01
Time
Audio
0:0 0 : 1 3
MULTI
To access the desired Track when there
is more than one in the disc.
4. Use the LEFT/RIGHT buttons to make the
desired setup and then press ENTER.
• You may use the number buttons of the remote
control to directly access a track and to start the
playback from the desired time.
Allows playback from a desired time.
You must enter the starting time as a
reference.
If a slide show is included with the
DVD-AUDIO, you can see this icon.
In this case you cannot use PAGE
PRE./NEXT buttons.
4. To make the screen disappear, press the INFO
button again.
If a video zone is included with the
DVD-AUDIO, you can see this icon.
In this case you cannot use PAGE
PRE./NEXT buttons.
DVD AUDIO
Group 01
Track 01
To access the desired Track when there
is more than one in the disc.
Allows playback from a desired time by
using the number buttons.
Page 01
Note
• Some Super Audio CD discs do not include a CD
layer.
• Depending on a disc, this function may not work.
If you want to change the 2channel or
multi channel play or stop mode, press
AUDIO button.
- You can use this function when Super
Audio CD disc includes multi channel
and 2 channel audio format.
• 2CH : L, R
• MULTI : F/L, F/R, R/L, R/R, C/T, S/W
Time
0: 00: 13
Allows playback of the music from a
desired time by using the number buttons.
Page, Index Function
Note
Some DVD-AUDIO discs don’t audio down-mixing.
These discs always output 5.1ch analog audio
regardless of audio setup.
1. Use PAGE PRE./NEXT buttons to Skip the Page
when there is more than one in a group.
• Some DVD-AUDIO discs include a slide show. In
the slide show mode, this function can not use.
• PAGE is still images. You can see the still
images when playback DVD-AUDIO disc.
2. Use INDEX PRE./NEXT buttons to Skip the Index
when there is more than one in a track.
Note Depending on a disc, this function may not work.
5. To make the screen disappear, press the INFO
button again.
ENG-24
ENG-25
DVD AUDIO Playback
REPEAT Play
1. Press the REPEAT button on the remote during
playback.
2. Select Title ( ), Group (
LEFT/RIGHT button.
) using the
3. Press ENTER.
Clips Menu for MP3/WMA/JPEG/MPEG4
Discs with MP3/WMA/JPEG/MPEG4 contain
individual songs, pictures or movies that can
be organized into folders as shown below.
They are similar to how you use your
computer to put files into different folders.
1. Open the disc tray.
2. Place the disc on the tray.
- Place the disc with the labeled side up.
3. Close the tray.
- The tray closes and you should get a screen
that looks like the one below.
MP3/WMA Playback
The folder can only be selected in the Stop
mode.
• To select the Parent Folder
Press the RETURN button to go to parent folder,
or use the UP/DOWN buttons to select “..” and
press ENTER to go to the parent folder.
• To select the Peer Folder
Use the LEFT/RIGHT buttons to highlight left
window. Use the UP/DOWN buttons to select the
desired folder, then press ENTER.
• To select the Sub-Folder
Use the LEFT/RIGHT buttons to highlight right
window. Use the UP/DOWN buttons to select the
desired folder, then press ENTER.
Off
00:00:23
Folder Selection
1_mp3
1. Open the disc tray.
2. Place the disc on the tray.
- Place the disc with the labeled side up.
3. Close the tray.
- The tray closes and you should get a screen
that looks like the one below.
MP3/WMA Play Function
1. Select the desired folder.
2. Use the UP/DOWN or LEFT/RIGHT buttons to
select a song file.
3. Press ENTER to begin playback of the song file.
B e c a u s e Yo u
AUDIO Format Display
Cactus
Root
Sad Day
During DVD AUDIO playback, press the AUDIO
button to see AUDIO Format information.
Wonderful
WMA
• LPCM : Linear Pulse Code Modulation.
Not compressed Audio data format.
• PPCM : Packet Pulse Code Modulation.
Lossless compressed Audio data format.
JPEG
Parent Folder
MP3
Parent Folder, Current Folder
and Peer Folders
•
Folders and Files in
Current Folder
: Name of currently playing file.
MUSIC
Current Folder
1st
Sub-Folders
2nd
•
Repeat/Random playback
: Current Playback Time.
SONG FILE 1
•
Note
Some DVD-AUDIO discs don’t allow audio
down-mixing. These discs always output 5.1ch
analog audio regardless of audio setup.
: Current Playback Mode : There are 4
modes. They can be selected in order by
pressing the REPEAT button.
- Off : Normal Playback
- Track : Repeats the current track.
- Folder : Repeats the current folder.
- Random : Files in the disc will be played
in random order.
Note When you play a MPEG4(AVI) file, refer
to page 28.
•
: MP3 file icon.
•
: AVI file icon.
•
: WMA file icon.
•
: Folder icon.
•
: JPEG file icon.
•
: Current Folder
icon.
ENG-26
Peer Folders
SONG FILE 2
SONG FILE 3
MPEG4 FILES
Press the REPEAT button to change playback
mode. There are 4 modes, such as Off, Track,
Folder and Random.
- Off : Normal Playback
- Track : Repeats the current song file.
- Folder : Repeats the song files which have the
same extension in the current folder.
- Random : Song files which have the same
extension will be played in random
order.
* To resume normal play, press the CLEAR button.
ENG-27
MP3/WMA Playback
CD-R MP3/WMA discs
When you record MP3 or WMA files on CD-R,
please refer to the following.
• Your MP3 or WMA files should be ISO 9660 or JOLIET
format.
ISO 9660 format and Joliet MP3 or WMA files are
compatible with Microsoft's DOS and Windows, and with
Apple's Mac. This format is the most widely used.
• When naming your MP3 or WMA files, do not exceed 8
characters, and enter “.mp3, .wma” as the file
extension.
General name format of: Title.mp3. or Title.wma.
When composing your title, make sure that you use 8
characters or less, have no spaces in the name, and avoid
the use of special characters including: (.,/,\,=,+).
MPEG4 Playback
MPEG4 Playback
1. Open the disc tray.
Using the Display Function
2. Place the disc on the tray.
- Place the disc with the labeled side up.
1. During play, press the INFO button on the remote.
3. Close the tray.
- The tray closes and you should get a screen
that looks like the one below.
MPEG4 Play Function
AVI files are used to contain the audio and video
data. Only AVI format files with the “.avi” extensions
can be played.
1. Select the desired folder. (See page 27 to select
the folder)
2. Use the UP/DOWN buttons to select the desired
item.
• Use a decompression transfer rate of at least 64Kbps
when recording WMA files.
Sound quality with WMA files basically depends on the
rate of compression/decompression you choose.
Getting CD audio sound requires an analog/digital
sampling rate, that is conversion to WMA format, of at
least 64Kbps and up to 192Kbps.
Conversely, files with decompression rates below 64Kbps
or over 192Kbps will not be played properly.
• Do not try recording copyright protected MP3 files.
Certain "secured" files are encrypted and code protected
to prevent illegal copying. These files are of the following
types: Windows MediaTM (registered trade mark of
Microsoft Inc) and SDMITM (registered trade mark of The
SDMI Foundation). You cannot copy such files.
• Important: The above recommendations cannot be taken
as a guarantee that the DVD player will play MP3
recordings, or as an assurance of sound quality. You
should note that certain technologies and methods for
MP3 file recording on CD-Rs prevent optimal playback of
these files on your DVD player (degraded sound quality
and in some cases, inability of the player to read the files).
2. Use the UP/DOWN or LEFT/RIGHT buttons to
select an avi file (DivX/XviD) and then press the
ENTER button.
(
3. Use the LEFT/RIGHT buttons to make the
desired setup and then press ENTER.
• You may use the number buttons of the remote
control to directly access a title or to start the
playback from the desired time.
(
4. To make the screen disappear, press the INFO
button again.
Function
Description
Skip
or
During play, press the
or
button, it moves forward
or backward 5 minutes.
During play, press the SERACH
(
or
) button and press
again to search at a faster
speed. Allows you to search
at a faster speed in an AVI
file. (2X, 4X, 8X)
Allows you to search at a
slower speed in an AVI file.
(1/8X, 1/4X, 1/2X)
Each time the STEP button
is pressed, a new frame will
appear.
)
Search
or
)
Slow Motion
Play
DivX
Title
Time
• Use a decompression transfer rate of at least 128
Kbps when recording MP3 files.
Sound quality with MP3 files basically depends on the rate
of compression/decompression you choose. Getting CD
audio sound requires an analog/digital sampling rate, that
is conversion to MP3 format, of at least 128 Kbps and up
to 160 Kbps. However, choosing higher rates, like 192
Kbps or more, only rarely give better sound quality.
Conversely, files with decompression rates below 128
Kbps will not be played properly.
MPEG4 Function Description
Audio
Subtitle
Size
Step Motion
Play
01
0: 00: 13
Reference page
-
-
P 14
P 14
MP3 1/8
ZOOM
None
640x272
2X/4X/2X/Normal in order
P 23
- These functions may not work depending on
MPEG4 file.
CD-R AVI file
To access the desired title when there is
Title more than one in the disc.
Allows playback of the film from a
Time desired time. You must enter the starting
time as a reference.
To select the desired language of the
Audio title soundtrack. The MP3, AC3 and
WMA are supported. You can use this
function using the AUDIO button.
(See page 20)
Repeat Playback
Press the REPEAT button to change playback
mode. There are 4 modes, such as Off, Folder, Title
and A-B (a distance between two points appointed
by user).
Off
F
FD
T
01 A - B
REPEAT
ENTER
) : repeats the AVI files which have the same
extension in the current folder.
• Title ( ) : repeats the title that is playing.
• A-B : repeats a segment of the file that you select.
T
• This unit can play a maximum of 3,000 files and 300
folders per disc.
ENG-28
F
This unit supports all resolutions up to maximum below.
You will be able to choose the subtitle
Subtitle languages or, if you prefer, turn them off
from the screen. You can use this
function using the SUBTITLE button.
(See page 20)
Size
• Folder (
This unit can play the following video compression
formats within the AVI file format:
- DivX 3.11 contents
- DivX 4 contents (Based on MPEG-4 Simple
Profile)
- DivX 5 contents (MPEG-4 simple profile plus
additional features such as bi-directional frames.
Qpel and GMC are also supported.)
- XviD MPEG-4 compliant Contents.
File Size has a relationship with
resolution of a title. The larger file size
is, the higher resolution is displayed.
If the file resolution is small, it scales up
automatically. So you can see the larger
screen.
DivX3.11 & DivX4 & XviD
DivX5
Bitrate may fluctuate:
Device may skip decoding
the high bitrate portions
and begin decoding again
when Bitrate returns to
normal.
720 x 480 @30fps
720 x 576 @25fps
: Maximum bitrate : 4Mbps
Note
• Some MPEG-4 files created on a personal
computer may not be play back. That is why Codec
Type, Version and Higher resolution over
specification is not supported.
• This unit supports CD-R/RW written in MPEG4 in
accordance with the “ISO9660 format”.
ENG-29
Picture CD Playback
Using the Setup Menu
1. Select the desired folder. (See page 27 to select
the folder)
2. Use the UP/DOWN buttons to select a Picture file in
clips menu and then press the ENTER button. You
should get a screen that looks like the one below.
ENTER RETURN
Note
• If no buttons on the remote control pressed for 10
seconds, the menu will disappear.
Press the INFO button on the remote control to
display the menu again.
• Press the STOP button to return to the clips menu.
• When playing a Kodak Picture CD, the unit
displays the Photo directly, not the clips menu.
CD-R JPEG Discs
• Use the INFO button on the remote control to select
the menu you want to view and then press the ENTER
button.
•
: Returns to the Album Screen.
• To see the next 6 pictures, press the
• To see the previous 6 pictures, press the
button.
button.
•
: Each time the ENTER button is pressed, the
picture rotates 90 degrees clockwise.
•
: Each time the ENTER button is pressed, the
picture is enlarged up to 4X.
(Normal ➝ 2X ➝ 4X ➝ 2X ➝ Normal)
•
: The unit enters slide show mode.
*Before beginning the Slide Show, the picture interval
must be set.
TIMER:
•
ENTER RETURN
: When this icon is selected and ENTER is
pressed, the pictures change automatically
with about a 6 second interval.
•
: The pictures change automatically with about
a 12 second interval.
•
: The pictures change automatically with about
a 18 second interval.
• Only files with the ".jpg" and ".JPG" extensions can
be played.
• If the disc is not closed, it will take longer to start
playing and not all of the recorded files may be
played.
• Only CD-R discs with JPEG files in ISO 9660 or Joliet
format can be played.
• The name of the JPEG file may not be longer than 8
characters and should contain no blank spaces or
special characters (. / = +).
• Only a consecutively written multisession disc can be
played. If there is a blank segment in the multisession
disc, the disc can be played only up to the blank
segment.
• A maximum of 3000 images can be stored on a single
CD.
• Kodak Picture CDs are recommended.
• When playing a Kodak Picture CD, only the JPEG
files in the pictures folder can be played.
• Kodak Picture CD : The JPEG files in the pictures
folder can be played automatically.
• Konica Picture CD : If you want to see the Picture,
select the JPEG files in the clips menu.
• Fuji Picture CD : If you want to see the Picture, select
the JPEG files in the clips menu.
• QSS Picture CD : The unit cannot play QSS Picture
CD.
• If the number of files in 1 Disc is over 3000, only 3000
JPEG files can be played.
• If the number of folders in 1 Disc is over 300, only
JPEG files in 300 folders can be played.
The Setup menu lets you customize your DVD
player by allowing you to select various
language preferences, set up a parental level,
even adjust the player to the type of television
screen you have.
Setting Up the Language Features
If you set the player menu, disc menu, audio
and subtitle language in advance, they will
come up automatically every time you watch a
movie.
Using the Player Menu Language
1. With the unit in Stop mode, press the MENU
button on the remote. Select Setup using
UP/DOWN buttons, then press the RIGHT or
ENTER button.
1. With the unit in Stop mode, press the MENU
button.
2. Select Setup using UP/DOWN buttons, then
press the RIGHT or ENTER button.
Language Setup : Setup of the Language.
Audio Setup : Setup of the Audio Options.
3. Select Language Setup using UP/DOWN
buttons, then press the RIGHT or ENTER button.
Display Setup : Setup of the Display Options.
Use to select which type of screen you want to
watch and several display options.
Parental Setup : Setup of the Parental Level.
Allows users to set the level necessary to
prevent children from viewing unsuitable
movies such as those with violence, adult
subject matter, etc.
DivX(R) Registration : Please use the
Registration code to register this player with
the DivX(R) Video on Demand service.
This will allow you to rent and purchase videos
using the DivX(R) Video On Demand format.
To learn more go to www.divx.com/vod.
Disc Menu
Title Menu
4. Select Player Menu using UP/DOWN buttons,
then press the RIGHT or ENTER button.
LANGUAGE SETUP
5. Use the UP/DOWN buttons to select the desired
language.
Function
Setup
2. Use the UP/DOWN buttons on the remote to
access the different features.
3. Press the ENTER or RIGHT button to access the
sub features.
To make the setup screen disappear after setting
up, press the MENU button again.
6. Press the ENTER button.
- The language is selected and the screen returns to
Language Setup menu.
- To make the SETUP menu disappear, press the
RETURN or LEFT button.
Note
Depending on a disc, some Setup Menu selections
may not work.
*Depending on a file size, the amount of time between
each picture may be different from the manual.
*If you don’t press any button, the slide show will start
automatically in about 10 seconds by default.
ENG-30
ENG-31
Setting Up the Language Features
Setting Up the Language Features
Setting Up the Audio Options
Using the Disc Menu Language
Using the Audio Language
Using the Subtitle Language
1. With the unit in Stop mode, press the MENU button.
This function changes the text language only on the
disc menu screens.
1. With the unit in Stop mode, press the MENU
button.
1. With the unit in Stop mode, press the MENU
button.
2. Select Setup using UP/DOWN buttons, then
press the RIGHT or ENTER button.
1. With the unit in Stop mode, press the MENU
button.
2. Select Setup using UP/DOWN buttons, then
press the RIGHT or ENTER button.
2. Select Setup using UP/DOWN buttons, then
press the RIGHT or ENTER button.
3. Select Audio Setup using UP/DOWN buttons,
then press the RIGHT or ENTER button.
2. Select Setup using UP/DOWN buttons, then
press the RIGHT or ENTER button.
3. Select Language Setup using UP/DOWN
buttons, then press the RIGHT or ENTER button.
3. Select Language Setup using UP/DOWN
buttons, then press the RIGHT or ENTER button.
3. Select Language Setup using UP/DOWN
buttons, then press the RIGHT or ENTER button.
4. Select Audio using UP/DOWN buttons, then
press the RIGHT or ENTER button.
4. Select Subtitle using UP/DOWN buttons, then
press the RIGHT or ENTER button.
4. Select Disc Menu using UP/DOWN buttons, then
press the RIGHT or ENTER button.
5. Use the UP/DOWN buttons to select the desired
language.
5. Use the UP/DOWN buttons to select the desired
language.
5. Use the UP/DOWN buttons to select the desired
language.
- Select “Original” if you want the default soundtrack
language to be the original language the disc is
recorded in.
- Select “Automatic” if you want the subtitle language to
be the same as the language selected as the audio
preference.
- Select “Others” if the language you want is not listed.
- Select “Others” if the language you want is not listed.
Some discs may not contain the language you select
as your initial language; in that case the disc will use its
original language setting.
- Select “Others” if the language you want is not listed.
AUDIO LANGUAGE
4. Use the UP/DOWN buttons to select the desired
item. Then press the RIGHT or ENTER button.
AUDIO SETUP
Audio
SUBTITLE LANGUAGE
Automatic
Original
Others
Dolby/DTS Digital Out
: PCM
MPEG-2 Digital Out
: PCM
Dynamic Compression
: On
PCM Down Sampling
: On
Speaker Setup
Subtitle
Others
6. Press the ENTER button.
Dolby/DTS Digital Out
6. Press the ENTER button.
1. PCM : Converts to PCM(2CH) audio.
2. Bitstream : Outputs Dolby Digital or DTS Bitstream via
digital output. Select Bitstream when connecting to a
Dolby digital and DTS Decoder.
- The language is selected and the screen returns to
Language Setup menu.
- The language is selected and the screen returns to
Language Setup menu.
6. Press the ENTER button.
- The language is selected and the screen returns to
Language Setup menu.
Note There is no analog audio output when you play
DTS sound disc.
Note
• If the selected language is not recorded on the
disc, the original pre-recorded language is
selected.
• How to make the SETUP menu disappear or
return to menu screen during set up;
Press RETURN or LEFT button.
ENG-32
MPEG-2 Digital Out
1. PCM : Converts to PCM(2CH) audio.
2. Bitstream : Outputs MPEG-2 Bitstream via digital
output. Select Bitstream when connecting to an
MPEG-2 Decoder.
Dynamic Compression
1. On : To select dynamic compression.
2. Off : To select the standard range.
ENG-33
Setting Up the Audio Options
Surround Sound Speaker Setup
1. With the unit in Stop mode, press the MENU
button.
PCM Down Sampling
1. On : Select this when the amplifier connected to the
player is not 96KHz compatible. In this case, the
96KHz signals will be down converted to 48KHZ.
2. Select Setup using UP/DOWN buttons, then
press the RIGHT or ENTER button.
2. Off : Select this when the amplifier connected to the
player is 96KHz compatible. In this case, all
signals will be output without any changes.
3. Select Audio Setup using UP/DOWN buttons,
then press the RIGHT or ENTER button.
Note Even when PCM Down sampling is Off
• Some discs will only output down sampled
audio through the digital outputs.
• High sampling rate DVD-Audio discs (192KHz
• When playing LPCM or PPCM DVD protected
by copyright. If digital audio source is
48KHz/16bit the Digital output is mute.
4. Use the UP/DOWN buttons to select Speaker
Setup. Then press the RIGHT or ENTER button.
Note
• How to make the SETUP menu disappear or
return to menu screen during set up;
Press RETURN or LEFT button.
• Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
• “DTS” and “DTS Digital Out” are trademarks of
Digital Theater Systems, Inc.
• DVD-AUDIO
- Outputs 2 channel digital audio only.
- Some DVD-AUDIO discs do not downmix, so they
will not output 2 channel digital audio.
- MULTI channel DVD-AUDIO discs play back
through the analog outputs.
• Super Audio CD
- Outputs analog signals only.
• HDMI
- If your TV is not compatible with compressed
multi-channel formats(Dolby Digital, DTS,
MPEG), you should set Digital Audio to PCM.
- If your TV is not compatible with LPCM sampling
rate over 48kHz, you should set PCM Down
Sampling to On.
- Super Audio CD audio is only available through
the analog outputs. It is not possible to output
Super Audio CD audio via the HDMI output or
Digital Audio Output.
The default settings : FRONT L, R (Small), CENTER
(Small), SURROUND (Small).
Select the size of the speakers to be connected.
• Front (FL, FR)
- Large: Normally select this.
- Small: When the sound distorts or the surround
sound effects are difficult to hear, select this.
This activates the Dolby Digital bass redirection
circuitry and outputs the bass frequencies of the
speaker from the subwoofer.
• Center
- None: If you do not connect a center speaker,
select this.
- Large: Normally select this.
- Small: When the sound distorts, select this.
This activates the Dolby Digital bass redirection
circuitry and outputs the bass frequencies of the
center speaker from other speakers.
or 176.4KHz) always output audio down
sampled to 96KHz or 88.2KHz through the
digital outputs.
Speaker Setup (See pages 34~35)
Surround Sound Speaker Setup
AUDIO SETUP
Dolby/DTS Digital Out
: PCM
MPEG-2 Digital Out
: PCM
Dynamic Compression
: On
PCM Down Sampling
: On
Speaker Setup
• Surround (SL, SR)
- None: If you do not connect a center speaker,
select this.
- Large (Rear/Side): Normally select either of these
according to the rear speaker’s position.
- Small (Rear/Side): When the sound distorts or the
surround sound effects are difficult to hear, select
either of these according to the rear speaker’s
position. This activates the Dolby Digital bass
redirection circuitry and outputs the bass
frequencies of the rear speaker from other
speakers.
Setting Up the Display Options
1. With the unit in Stop mode, press the MENU
button.
2. Select Setup using UP/DOWN buttons, then
press the RIGHT or ENTER button.
3. Select Display Setup using UP/DOWN buttons,
then press the RIGHT or ENTER button.
4. Use the UP/DOWN buttons to select the desired
item. Then press the RIGHT or ENTER button.
HDMI/DVI
TV ASPECT
5. Use the UP/DOWN or LEFT/RIGHT buttons to
select the desired item. Then press the ENTER
button.
ENG-34
SPEAKER SETUP
On
Setting up TEST
4:3 Letter Box
4:3 Pan Scan
The test output signals come clockwise starting from
the Front Speaker(L). Adjust Channel Balance to
match to the volume of test signals memorized in
the system.
16:9 Wide
FRONT(L) ➝ CENTER ➝ SUBWOOFER ➝
FRONT(R) ➝ SURROUND(R) ➝ SURROUND(L)
Note
How to make the SETUP menu disappear or return
to menu screen during set up. Press RETURN or
LEFT button.
• The subwoofer test output signal is lower than the
other speakers.
• The MPEG Multichannel logo is a trademark
registered by PHILIPS Corporation.
• If you set Front (L, R) “Small”, LFE (Subwoofer) is
set “On” automatically.
ENG-35
Setting Up the Display Options
Setting Up the Display Options
Important Note
TV Aspect
Depending on the type of television you have, you may
want to adjust the screen setting (aspect ratio).
1. 4:3 Letter Box : Select when you want to see the total
16:9 ratio screen DVD supplies, even though you have
a TV with a 4:3 ratio screen. Black bars will appear at
the top and bottom of the screen.
2. 4:3 Pan Scan : Select this for conventional size TVs
when you want to see the central portion of the 16:9
screen. (Extreme left and right side of movie picture
will be cut off.)
• In case of differ from your TV and TV system
setting value video output may be blocked.
• You have to setup TV system correctly.
• Refer to your TV user's manual.
• If you use NTSC disc at PAL TV system, motion
picture may be distorted.
• If you use PAL disc at NTSC TV system, motion
picture may be distorted.
3. 16:9 Wide : You can view the full 16:9 picture on your
widescreen TV.
Video Output
Select Video Output.
Still Mode
These options will help prevent picture shake in still
mode and display small text clearer.
HDMI/DVI
This setting is used when the unit is connected by HDMI
or DVI with Display devices (TV, projector, etc).
1. Resolution
- 480p/576p : 720 x 480, 720 x 576
- 720p : 1280 x 720
- 768p : 1024 x 768
- 1080i : 1920 x 1080
2. DVI Output
You can use this function to DVI output format.
• This function corrects a biased TV screen to secure
a normal view.
• If DVI Output is set incorrectly, the screen can be
biased.
1. S-Video : Select when you want to use Video and
S-Video Out.
1. Auto : When selecting Auto, Field/Frame mode will be
automatically converted.
2. Component (Iscan) : Select when you want to use
Video and Component 525i(Interlace) Out
2. Field : Select this feature when the screen shakes in
the Auto mode.
Setting Up the Parental Control
The Parental Control function works in conjunction
with DVDs that have been assigned a rating which
helps you control the types of DVDs that your family
watches. There are up to 8 rating levels on a disc.
1. With the unit in Stop mode, press the MENU
button.
2. Select Setup using UP/DOWN buttons, then
press the RIGHT or ENTER button.
3. Select Parental Setup using UP/DOWN buttons,
then press the RIGHT or ENTER button.
HDMI/DVI SETUP
Resolution
: 576p
DVI Output
: Mode B
3. Component (Pscan) & HDMI : Select when you want
to use Component 525p(Progressive) Out or HDMI.
3. Frame : Select this feature when you want to see
small letters more clearly in the Auto mode.
* If you press the VIDEO SEL. button, Video output
mode is changed in regular sequence in no disc
mode.
(S-Video ➝ Iscan ➝ Pscan & HDMI ➝ SCART RGB
➝ SCART VIDEO)
Screen Messages
Use to turn on-screen messages On or Off.
Black Level
Adjusts the brightness of the screen.(On/Off)
4. SCART Output : Select when you want to use Scart
Out.
TV System
• RGB : Select when you want to use SCART RGB
Out.
1. NTSC Disc : In case of using NTSC disc
• If your TV system only has PAL-Video input, you
must choose “PAL”. When you choose “PAL”,
Interlace output format is PAL 60 Hz output.
• Video : Select when you want to use SCART
Video Out.
* If the Yes/No selection in the Display Setup sub Menu
is not made within 10 seconds, the screen returns to
the previous menu.
• If your TV system only has NTSC, input you must
choose “NTSC Output”.
• If you set up the NTSC TV system, HDMI output
frame rate is 60 Hz.
2. PAL Disc : In case of using PAL disc
• If your TV system only has NTSC-Video input, you
must choose “NTSC Output”.
(Iscan)
(Pscan) & HDMI
• If your TV system only has PAL input, you must
choose “PAL Output”.
• If you set up the PAL TV system, HDMI output frame
rate is 50 Hz.
Important Note
4. Use RIGHT or ENTER to select Yes if you want
to use a password. The Enter Password screen
appears.
• Consult your TV User’s Manual to find out if your
TV supports Progressive Scan. If Progressive
Scan is supported, follow the TV User’s Manual’s
instructions regarding Progressive Scan settings in
the TV’s menu system.
PARENTAL SETUP
Use Password
: No
• If Video Output is set incorrectly, the screen can be
blocked. (See page 42)
• The resolutions available for HDMI outputs depend
on the connected TV or projector. For details, see
the user’s manual of your TV or projector.
• When the resolution changes, the image may be
corrupted or the output may take longer than normal.
5. Enter your password. The Re-enter Password
screen appears to confirm the password.
Enter your password again.
The player is locked ( ).
CREATE PASSWORD
Enter Password
- - - -
0~9
HDMI/DVI
ENG-36
ENG-37
Setting Up the Parental Control
CREATE PASSWORD
Controlling a TV with the Remote
5. Select Rating Level using UP/DOWN buttons,
and press ENTER or RIGHT button.
The remote can also be set up to control most TVs. To program the remote, use the code that
corresponds to your brand.
TV Codes
Re-enter Password
- - - -
0~9
6. Select the Rating Level you want using
UP/DOWN buttons.
For example, if you select up to Level 6, discs that
contain Level 7, 8 will not play.
- To cancel the Rating Level, select No using RIGHT or
ENTER in Use Password.
Setting Up the Rating Level
e.g) Setting up in LEVEL6.
1. With the unit in Stop mode, press the MENU
button.
RATING LEVEL
Level 8 Adult
Level 7
Level 6
Level 5
Level 4
Level 3
Level 2
Level 1 Kids Safe
2. Select Setup using UP/DOWN buttons, then
press the RIGHT or ENTER button.
The player is locked ( ).
About the Change Password
- Highlight Change Password using UP/DOWN buttons.
- Press ENTER button.
The Change Password screen appears.
- Enter your new password. Enter the new password again.
3. Select Parental Setup using UP/DOWN buttons,
then press the RIGHT or ENTER button.
4. Enter your password.
The Parental Setup screen appears.
PASSWORD CHECK
Note
• How to make the SETUP menu disappear or
return to menu screen during set up;
Press RETURN or LEFT button.
• If you have forgotten your password, see page 41.
BRAND
ANAM
AIWA
BANG&OLUFSEN
BLAUPUNKT
BRANDT
BRIONVEGA
CGE
CONTINENTAL EDISON
DAEWOO
EMERSON
FERGUSON
FINLUX
FORMENTI
FUJITSU
GRADIENTE
GRUNDIG
HITACHI
IMPERIAL
JVC
LG
LOEWE
LOEWE OPTA
MAGNAVOX
METZ
MITSUBISHI
MIVAR
NEC
NEWSAN
NOBLEX
CODE
10, 11, 12, 13, 14, 15, 16, 17, 18
82
57
71
73
57
52
75
19, 20, 23, 24, 25, 26, 27, 28, 29,
30 , 31, 32, 33, 34
64
73
06, 49, 57
57
84
70
49, 52, 71
60, 72, 73, 75
52
61, 79
06, 19, 20, 21, 22, 78
06, 69
06, 57
40
57
06, 48, 62, 65
52, 77
83
68
66
1. Turn on the TV.
BRAND
NORDMENDE
NOKIA
PANASONIC
PHILPS
PHONOLA
PIONEER
RADIOLA
RADIOMARELLI
RCA
REX
SABA
SALORA
SAMSUNG
SANYO
SCHNEIDER
SELECO
SHARP
SIEMENS
SINGER
SINUDYNE
SONY
TELEAVA
TELEFUNKEN
THOMSON
THOMSON ASIA
TOSHIBA
WEGA
YOKO
ZENITH
CODE
72, 73
74
53, 54, 74, 75
06, 55, 56, 57
06, 56, 57
58, 59, 73, 74, 75
06, 56
57
45, 46
74
57, 72, 73, 74, 75
74
01, 02, 03, 04, 05, 06, 07, 08, 09
41, 42, 43, 44, 48
06
74
36, 37, 38, 39, 48
71
57
57
35, 48
73
67, 73, 75, 76
72, 73, 75
80, 81
47, 48, 49, 50, 51, 52
57
06
63
2. Point the DVD’s remote at the TV.
4. If the TV turns off, setup is complete.
Enter other codes of the same brand if the first
code does not work.
3. While holding the TV POWER button down, enter
the code for your brand.
5. To operate the TV, use the “TV Function Buttons”
described on page 9.
Enter Password
Important Note
- - - -
e.g) For Samsung 2 TVs
While holding down the TV POWER button,
enter 0 and then 1.
0~9
ENG-38
• The remote may not be able to control every
model TV of the brands listed.
• If you replace the remote control's batteries, set
the brand code again.
ENG-39
Firmware upgrade
Introduction
Troubleshooting
4. Press the ENTER button.
Samsung will often support the software upgrade to
improve the performance of this unit to the latest
status, through Samsung Internet Site
(www.samsung.com).
Because the specially new mpeg4 codec continues
and it is appearing. What improvements are made
depends on the upgrade software you are using as
well as the software that your DVD-player contained
before the upgrade.
How to make an upgrade disc
Write the downloaded file onto a blank CD-R or
CD-RW disc, using the following settings:
1. You have to download a new file through
Download Center of Samsung Internet Site
(www.samsung.com).
Before requesting service (troubleshooting), please check the following.
Firmware upgrade starts
Problem
5. In the middle of the writing, the tray will open
automatically. After taking out the disc, please
wait for about 2 minutes.
6. If the unit was successfully updated, the unit will
turn off and on after closing the tray automatically.
When the unit turns on, this screen will display.
2. Write the file to Disc using CD-RW of your
computer.
Action
Page
No operations can be
performed with the remote.
• Check the batteries in the remote. They may need replacing.
• Operate the remote control at a distance of no more than 20 feet.
• Remove batteries and hold down one or more buttons for several
minutes to drain the microprocessor inside the remote to reset it.
Reinstall batteries and try to operate the remote again.
P3
Disc does not play.
• Ensure that the disc is installed with the label side facing up.
• Check the region number of the DVD.
P6
5.1 channel sound is not
being reproduced.
• 5.1 channel sound is reproduced only when the following conditions
are met. :
1) The DVD player is connected with the proper amplifier
2) The disc is recorded with 5.1 channel sound.
• Check whether the disc being played has the “Dolby 5.1 ch” mark
on the outside.
• Check if your audio system is connected and working properly.
• In a SETUP Menu, is the Audio Output set to Bitstream?
P10
• The features or action cannot be completed at this time because:
1. The DVD’s software restricts it.
2. The DVD’s software doesn’t support the feature (e.g., angles).
3. The feature is not available at the moment.
4. You’ve requested a title or chapter number or search time that is
out of range.
P14
The
icon appears on
screen.
P33
Note
• File System CD-ROM ISO Level
• Character set ISO 9660
Disc Menu doesn’t appear.
• Check if the disc has a Menu.
Play mode differs from the
Setup Menu selection.
• Some of the functions selected in the Setup Menu may not work
properly if the disc is not encoded with the corresponding function.
P31~38
The screen ratio cannot
be changed.
• The Screen Ratio is fixed on your DVDs.
P35~36
No audio.
• Make sure you have selected the correct Digital Output in the Audio
Options Menu.
P33~35
The screen is blocked
• Press power on from a cold start with no disc in the unit.
Press the SEARCH/SKIP (
) button on the front panel for 5
second. The SELECT MENU LANGUAGE display will appear.
Select the number button of the desired language.
P35~36
• Finalized, single session
• Write speed low
7. Select the desired language.
Note • If the “Select Menu Language” doesn't
appear, please contact to “Samsung
Service Center”.
• Do not press any button and unplug
the power code during upgrade.
Upgrade procedure
1. Press OPEN/CLOSE button to open the disc tray.
2. Insert the upgrade CD-R disc, label facing up.
• The upgrade procedure may change,
refer to the web site
(www.samsung.com).
3. Press OPEN/CLOSE button to close the disc tray.
Firmware upgrade appears on the display
Forgot password
If you experience other
problems.
ENG-40
• Press power on from a cold start with no disc in the unit.
Press the SEARCH/SKIP (
) button on the front panel for 5
second. The SELECT MENU LANGUAGE display will appear.
Select the number button of the desired language. Press the MENU
button, and then press DOWN button to select Setup, then press
RIGHT or ENTER. Press Up or Down to select Parental Setup The
Parental Setup is now unlocked as indicated on the display.
You can change your password.
• Go to the contents and find the section of the instruction book that
contains the explanations regarding the current problem, and follow
the procedure once again.
• If the problem still cannot be solved, please contact your nearest
authorized service center.
ENG-41
P37~38
Troubleshooting
Problem
No HDMI output.
Abnormal HDMI output
screen.
HDMI output Judder
Specifications
Action
• Check the Video output is HDMI enabled.
• Check the connection between the TV and the HDMI
jack of DVD player.
• See if the TV supports this 480p/576p/720p/768p/1080i DVD player.
• If snow noise appears on the screen, it means
that TV does not support HDCP (High-bandwidth Digital Content
Protection).
• Check your TV system setup correctly.
• The screen judder phenomenon may occur when frame rate is
converted from 50Hz to 60Hz for 720P/1080i DVI(Digital Visual
Interface) Output.
• Refer to your TV users manual.
Page
General
Power Requirements
AC 230 V, 50 Hz
Power Consumption
14 W
Weight
2.3 Kg
Dimensions
Operating Temperature Range
Operating Humidity Range
P12~13
DVD
(DIGITAL VERSATILE DISC)
P13
Disc
P37
+5°C to +35°C
10 % to 75 %
Reading Speed : 3.49 ~ 4.06 m/sec.
Approx. Play Time
(Single Sided, Single Layer Disc) : 135 min.
CD : 12Cm
(COMPACT DISC)
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 74 min.
CD : 8Cm
(COMPACT DISC)
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 20 min.
VCD : 12Cm
Composite Video
SCART Jack
Video
Output
Component Video
S-VIDEO
HDMI
SCART Jack
2 Channel
5.1 Channel
Audio
Output
430mm (W) X 250mm (D) X 49mm (H)
*Frequency Response
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 74 min. (Video + Audio)
1 channel : 1.0 Vp-p (75 Ω load)
R(Red) : 0.7 Vp-p (75 Ω load)
G(Green) : 0.7 Vp-p (75 Ω load)
B(Blue) : 0.7 Vp-p (75 Ω load)
Composite Video : 1.0 Vp-p (75 Ω load)
Luminance Signal : 1.0 Vp-p (75 Ω load)
Color Signal : 0.3 Vp-p (75 Ω load)
Y : 1.0 Vp-p (75 Ω load)
Pr : 0.70 Vp-p (75 Ω load)
Pb : 0.70 Vp-p (75 Ω load)
Luminance Signal : 1.0 Vp-p (75 Ω load)
Chrominance Signal : 0.3 Vp-p (75 Ω load)
High Definition Multimedia Interface
2 Channel : L(1/L), R(2/R)
L(1/L), R(2/R)
F/L, F/R, R/L, R/R, C/T, S/W
48 kHz Sampling : 4 Hz to 22 kHz
96 kHz Sampling : 4 Hz to 44 kHz
*S/N Ratio
110 dB
*Dynamic Range
100 dB
*Total Harmonic Distortion
0.004 %
*: Nominal specification
• Samsung Electronics Co., Ltd reserves the right to change the specifications without notice.
• Weight and dimensions are approximate.
ENG-42
ENG-43
UNITED KINGDOM
This Samsung product is warranted for the period of twelve (12) months
from the original date of purchase, against defective materials and
workmanship. In the event that warranty service is required, you should
return the product to the retailer from whom it was purchased.
However, Samsung Authorised Dealers and Authorised Service Centers in
other EC Countries will comply with the warranty on the terms issued to
purchasers in the country concerned. In case of difficulty, details of our
Authorised Service Centers are available from:
Samsung Electronics (U.K.) Ltd.,
Euro Service Centre, Stafford Park 12,
TELFORD, Shropshire TF3 3BJ,
Tel: 0870) 242 0303, Fax: 01952) 297617
■ WARRANTY CONDITIONS
1.The warranty is only valid if, when warranty service is required, the
warranty card is fully and properly completed and is presented with the
original invoice or sales slip or confirmation, and the serial number on the
product has not been defaced.
2. Samsung’s obligations are limited to the repair or, at its discretion,
replacement of the product or the defective part.
3. Warranty repairs must be carried out by Authorised Samsung Dealers or
Authorised Service Centers. No re-imbursement will be made for repairs
carried out by non Samsung Dealers and, any such repair work and
damage to the products caused by such repair work will not be covered
by this warranty.
REPUBLIC OF
IRELAND
5. This warranty covers none of the following:
a) Periodic check ups, maintenance and repair or replacement of parts
due to normal wear and tear.
b) Cost relating to transport, removal or installation of the product.
c) Misuse, including the faiure to use this product for its normal
purposes or incorrect installation.
d) Damage caused by Lightning, Water, Fire, Acts of God, War, Public
Disturbances, incorrect mains voltage, improper ventilation or any
other cause beyond the control of Samsung.
6. This warranty is valid for any person who legally acquired possession of
the product during the warranty period.
7. The consumers statutory rights in any applicable national legislation
whether against the retailer arising from the purchase contract or
otherwise are not affected by this warranty. Unless there is national
legislation to the contrary, the rights under this warranty are the
consumers sole rights and Samsung, its subsidiaries and distributors
shall not be liable for indirect or consequential loss or any damage to
records, compact discs, videos or audio taper or any other related
equipment or material.
SAMSUNG ELECTRONICS (U.K.) LTD.
4. This product is not considered to be defective in materials nor
workmanship by reason that it requires adaptation in order to conform to
national or local technical or safety standards in force in any Country
other than the one for which the product was originally designed and
manufactured. This warranty will not cover, and no re-imbursement will be
made for such adaptation nor any damage which may result.
ENG-44
ENG-45
Download PDF

advertising