Samsung | PPM50H3 | Samsung PPM50H3 User Manual

D61A-BN68-00492A-00_ENG
2003.11.18
9:31 AM
Page 1
PDP-MONITOR
(PLASMA DISPLAY PANEL)
PPM42S3
PPM50H3
PPM63H3
Owner’s Instructions
Before operating the unit,
please read this manual thoroughly,
and retain it for future reference.
Intended for Commercial Use and Operation
ON-SCREEN MENUS
PICTURE IN PICTURE (PIP)
VIDEO WALL
MDC (MULTIPLE DISPLAY CONTROL)
D61A-BN68-00492A-00_ENG
2003.11.18
9:31 AM
Page 2
Thank You for Choosing Samsung!
ENG
Thank you for choosing Samsung! Your new Samsung product represents the latest in PDP
technology. We designed it with easy-to-use on-screen menus, making it one of the best
products in its class. We are proud to offer you a product that will provide convenient,
dependable service and enjoyment for years to come.
Warning! Important Safety Instructions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO PREVENT ELECTRICAL SHOCK, DO NOT
REMOVE REAR COVER, NO USER SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash and arrow
head within the triangle is a
warning sign alerting you of
“dangerous voltage” inside
the product.
The exclamation point within
the triangle is a warning sign
alerting you of important
instructions accompanying
the product.
Note to CATV system installer: This reminder is provided to call CATV system installer's attention to Article 82040 of the National Electrical Code (Section 54 of Canadian Electrical Code, Part I), that provides guidelines for
proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of
the building as close to the point of cable entry as practical.
Caution: FCC/CSA regulations state that any unauthorized changes or modifications to this equipment may void
the user's authority to operate it.
Caution: To prevent electric shock, match the wide blade of plug to the wide slot, and fully insert the plug.
Attention: pour eviter les chocs electriques, introduire la lame le plus large de la fiche dans la borne
correspondante de la prise et pousser jusqu'au fond.
Important: One Federal Court has held that unauthorized recording of copyrighted TV programs is an
infringement of U.S. copyright laws.Certain Canadian programs may also be copyrighted and any unauthorized
recording in whole or in part may be in violation of these rights.
TO PREVENT DAMAGE WHICH MAY RESULT IN FIRE OR ELECTRIC SHOCK HAZARD, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
2
D61A-BN68-00492A-00_ENG
2003.11.18
9:31 AM
Page 3
Important Safety Informations (UL1492)
ENG
◆ Read all safety and operating instructions before operating your PDP.
◆ Keep the safety and operating instructions for future reference.
◆ Heed all warnings on the PDP and in the operating instructions.
◆ Follow all operating and use instructions.
◆ Unplug the PDP from the wall outlet before cleaning. Use a damp cloth; do not use liquid or aerosol
cleaners.
◆ Never add any attachments and/or equipment without approval of the manufacturer. Such additions
can increase the risk of fire, electric shock, or other personal injury.
◆ Do not use the PDP where contact with or immersion in water is a possibility, such as near bath tubs,
sinks, washing machines, swimming pools, etc.
◆ Do not place the PDP on an unstable cart, stand, tripod, bracket, table, or
floor where it can fall. A falling PDP can cause serious injury to a child or
adult, and serious damage to the appliance. Use only with a cart, stand,
tripod, bracket, or table recommended by the manufacturer or sold with
the PDP. Follow the manufacturer's instructions when mounting the unit,
and use a mounting accessory recommended by the manufacturer. Move
the PDP and cart with care. Quick stops, excessive force, and uneven
surfaces can make the unit and cart unsteady and likely to overturn.
◆ Provide ventilation for the PDP. The unit is designed with slots in the cabinet for ventilation to protect
it from overheating. Do not block these openings with any object, and do not place the PDP on a
bed, sofa, rug, or other similar surface. Do not place it near a radiator or heat register. If you place the
PDP on a rack or bookcase, ensure that there is adequate ventilation and that you've followed the
manufacturer's instructions for mounting.
◆ Operate your PDP only from the type of power source indicated on the marking label. If you are not
sure of the type of power supplied to your home, consult your appliance dealer or local power com
pany.
◆ Use only a grounded or polarized outlet. For your safety, this PDP is equipped with a polarized
alternating current line plug having one blade wider than the other. This plug will fit into the power
outlet only one way. If you are unable to insert the plug fully into the outlet, try reversing the plug. If
the plug still does not fit, contact your electrician to replace your outlet.
◆ Protect the power cord. Power supply cords should be routed so that they won’t be walked on or
pinched by objects placed on or against them. Pay particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the unit.
◆ Unplug the PDP from the wall outlet and disconnect the antenna or cable system during a lightning
storm or when left unattended and unused for long periods of time. This will prevent damage to the
unit due to lightning and power-line surges.
3
D61A-BN68-00492A-00_ENG
2003.11.18
9:31 AM
Page 4
Important Safety Informations (UL1492) (continued)
ENG
◆ Avoid overhead power lines. An outside antenna system should not be placed in the vicinity of
overhead power lines or other electric light or power circuits or where it can fall into such power
lines or circuits. When installing an outside antenna system, be extremely careful to keep from
touching the power lines or circuits. Contact with such lines can be fatal.
◆ Do not overload the wall outlet or extension cords. Overloading can result in fire or electric shock.
◆ Do not insert anything through the openings in the unit, where they can touch dangerous voltage
points or damage parts. Never spill liquid of any kind on the PDP.
◆ Ground outdoor antennas. If an outside antenna or cable system is connected to the PDP, be sure the
antenna or cable system is grounded so as to provide some protection against voltage surges and
built-up static charges. Section 810 of the National Electrical Code, ANSI/NFPA No.70-1984,
provides information about proper grounding of the mast and supporting structure, grounding of the
lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna
discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
◆ Do not attempt to service the PDP yourself. Refer all servicing to qualified service personnel. Unplug
the unit from the wall outlet and refer servicing to qualified service personnel under the following
conditions:
- when the power-supply cord or plug is damaged
- if liquid has been spilled on the unit or if objects have fallen into the unit
- if the PDP has been exposed to rain or water
- if the PDP does not operate normally by following the operating instructions
- if the PDP has been dropped or the cabinet has been damaged
- when the PDP exhibits a distinct change in performance
◆ If you make adjustments yourself, adjust only those controls that are covered by the operating
instructions. Adjusting other controls may result in damage and will often require extensive work by a
qualified technician to restore the PDP to normal.
◆ When replacement parts are required, be sure the service technician uses replacement parts specified
by the manufacturer or those that have the same characteristics as the original part. Unauthorized
substitutions may result in additional damage to the unit.
◆ Upon completion of any service or repairs to this PDP, ask the service technician to perform safety
checks to determine that the PDP is in a safe operating condition.
◆ The PDP can properly operate in a temperature range of 32~104°F(0~40°C) and 80% humidity. Do
not use in a hot and humid place.
◆ Before moving the PDP equipped with speakers, separate the speakers from the PDP. If you move the
PDP with the speakers attached, it may result in damage or injury.
4
D61A-BN68-00492A-00_ENG
2003.11.18
9:31 AM
Page 5
Important Safety Instructions (UL6500)
ENG
◆ Read these instructions.
◆ Keep these instructions.
◆ Heed all warnings.
◆ Follow all instructions.
◆ Do not use this apparatus near water.
◆ Clean only with dry cloth.
◆ Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions.
◆ Do not install near any heat sources such as radiators, heat registers, or other apparatus (including
amplifiers) that produce heat.
◆ Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit
into your outlet, consult an elec trician for replacement of the obsolete outlet.
◆ Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
◆ Only use attachments/accessories specified by the manufacturer.
◆ Use only with cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a used, caution when
moving the cart/apparatus combination to avoid injury from tip-over.
◆ Unplug this apparatus during lightning storms or when unused for long periods of time.
◆ Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
5
D61A-BN68-00492A-00_ENG
2003.11.18
9:31 AM
Page 6
FCC Information
ENG
User Instructions
Warning
The Federal Communications Commission Radio
Frequency Interference Statement includes the
following warning:
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation.
User must use shielded signal interface cables to
maintain FCC compliance for the product. Provided
with this monitor is a detachable power supply cord
with IEC320 style terminations. It may be suitable for
connection to any UL Listed personal computer with
similar configuration. Before making the connection,
make sure the voltage rating of the computer
convenience outlet is the same as the monitor and that
the ampere rating of the computer convenience outlet
is equal to or exceeds the monitor voltage rating.
For 120 Volt applications, use only UL Listed
detachable power cord with NEMA configuration 515P type (parallel blades) plug cap. For 240 Volt
applications use only UL Listed Detachable power
supply cord with NEMA configuration 6015P type
(tandem blades) plug cap.
If this equipment does cause harmful interference to
radio or PDP receptions, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures:
◆ Reorient or relocate the receiving antenna.
◆ Increase the separation between the equipment
and receiver.
◆ Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
◆ Consult the dealer or an experienced radio/PDP
technician for help.
IC Compliance Notice
This Class B digital apparatus meets all requirements of
the Canadian Interference-Causing Equipment
Regulations of ICES-003.
Cet appareil Numérique de classe B respecte toutes les
exigences du Règlemont NMB-03 sur les équipements
produisant des interférences au
Canada.
User Information
Notice de Conformité IC
Changes or modifications not expressly approved by
the party responsible for compliance could void the
user’s authority to operate the equipment. If necessary,
consult your dealer or an experienced radio/PDP
technician for additional suggestions. You may find the
booklet called. How to Identify and Resolve
Radio/PDP Interference Problems helpful. This booklet
was prepared by the Federal Communications
Commission. It is available from the U.S. Government
Printing Office, Washington, DC 20402, Stock
Number
004-000-00345-4 .
Cet appareil numérique de classe B respecte toutes les
exigences du Règlement ICES-003 sur les équipements
produisant des interférences au Canada.
The party responsible for product compliance:
SAMSUNG ELECTRONICS CO., LTD
America QA Lab of Samsung
3351 Michelson Drive,
Suite #290, Irvine, CA92612 USA
VCCI
This is a Class B product based on the standard of the
Voluntary Control Council for Interference by
Information Technology Equipment (VCCI). If this is
used near a radio or PDP receiver in a domestic
environment, it may cause radio interference. Install
and use the equipment according to the instruction
manual.
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe B est
conforme à la norme NMB-003 du Cananda.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
6
D61A-BN68-00492A-00_ENG
2003.11.18
9:31 AM
Page 7
Important Warranty Information Regarding PDP Format
Viewing
ENG
Wide screen format PDP Displays (16:9,the aspect ratio of the screen width to height) are primarily
designed to view wide screen format full-motion video. The images displayed on them should primarily
be in the wide screen 16:9 ratio format, or expanded to fill the screen if your model offers this feature and
constantly moving. Displaying stationary graphics and images on screen, such as the dark side-bars on
non-expanded standard format PDP video and programming, should be limited to no more than 5% of
the total PDP viewing per week.
Additionally, viewing other stationary images and text such as stock market reports, video game displays,
station logos, web sites or computer graphics and patterns, should be limited as described above for all
PDP displays. Displaying stationary images that exceed the above guidelines can cause uneven aging of
PDP Displays that leave subtle, but permanent burned-in ghost images in the PDP picture. To avoid
this, vary the programming and images, and primarily display full screen moving images, not stationary
patterns or dark bars. On PDP models that offer picture sizing features, use these controls to view
different formats as a full screen picture.
Be careful in the selection and duration of PDP formats used for viewing. Uneven PDP aging as a result
of format selection and use, as well as burned-in images, are not covered by your Samsung limited
warranty.
7
D61A-BN68-00492A-00_ENG
2003.11.18
9:31 AM
Page 8
User Instructions
ENG
◆ Screen Image retention
Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the
plasma display panel for more than 2 hours as it can cause screen image retention. This image
retention is also known as “screen burn”. To avoid such image retention, reduce the degree of
brightness and contrast of this screen when displaying a still image.
◆ Cell Defect
The plasma display panel consists of fine cells. Although the panels are produced with more than
99.9 percent active cells, there may be some cells that do not produce light or remain lit.
◆ Height
The PDP can normally operate only under 2000m in height. It might abnormally function at a place
over 2000m in height and do not install and operate there.
◆ Warranty
- Warranty does not cover any damage caused by image retention.
- Burn-in is not covered by the warranty.
☛
EUROPEAN NOTICE
Products with the CE marking comply with the EMC Directive
(89/336/EEC), (92/31/EEC), (93/68/EEC) and the Low Voltage
Directive (73/23/EEC) issued by the Commission of the
European Community. Compliance with these directives
implies conformity to the following European Norms:
8
■
EN55022:1998
Radio Frequency Interference
■
EN55024:1998
Electromagnetic Immunity
■
EN61000-3-2:2000
Power Line Harmonics
■
EN61000-3-3:1995
Voltage Fluctuations
■
EN60065
Product Safety
D61A-BN68-00492A-00_ENG
2003.11.18
9:31 AM
Page 9
Wiring the Mains Power Supply Plug (UK Only)
ENG
IMPORTANT NOTICE
The mains lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated on the
pin face of the plug and, if it requires replacing, a fuse approved to BSI1362 of the same rating must be used. Never use the plug
with the fuse cover omitted if the cover is detachable. If a replacement fuse cover is required, it must be of the same colour as the
pin face of the plug. Replacement covers are available from your dealer. If the fitted plug is not suitable for the power points in
your house or the cable is not long enough to reach a power point, you should obtain a suitable safety approved extension lead
or consult your dealer for assistance. However, if there is no alternative to cut off the plug, remove the fuse and then safely
dispose of the plug. Do NOT connect the plug to a mains socket as there is a risk of shock hazard from the bared flexible cord.
IMPORTANT
The wires in the mains lead are coloured in accordance with the following code:
BLUE - NEUTRAL
BROWN - LIVE
As these colours may not correspond to the coloured markings identifying the terminals in your plug, proceed as follows:
The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK.
The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED.
WARNING:
DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL, WHICH IS MARKED WITH THE LETTER E OR BY
THE EARTH SYMBOL , OR COLOURED GREEN OR GREEN AND YELLOW.
Checking Parts
PPM42S3 &
PPM50H3
Owner’s Instructions
Power Cord
Speaker Wires
(2EA)
PC Cable
MDC Cable
(RS232C)
Remote Control/
AAA Batteries
2 Install CD
- MDC Software (RS232C) Ferrite Cores for
Speaker Wire
- Pivot software
(2EA)
Stand-Base
(2EA)
Screws
(4EA)
DNIeTM (Digital Natural Image engine)
This feature bring you more detailed image with 3D noise reduction, detail enhancement, contrast
enhancement and white enhancement. New image compensation Algorithm gives brighter, clearer,
much detailed image to you. DNIeTM technology will fit every signals into your eyes.
9
D61A-BN68-00492A-00_ENG
2003.11.18
9:31 AM
Page 10
ENG
Contents
◆ FOREWORD
■
■
■
■
■
■
■
Warning! Important Safety Instructions .........................................................
Important Safety Informations (UL1492) .......................................................
Important Safety Informations (UL6500) .......................................................
FCC Information ............................................................................................
Important Warranty Information Regarding PDP Format Viewing.................
User Instructions............................................................................................
Wiring the Mains Power Supply Plug (UK Only)............................................
2
3
5
6
7
8
9
◆ CONNECTING AND PREPARING YOUR DISPLAY
■
■
■
■
■
■
■
■
■
■
Your New Plasma Display Panel...................................................................
Becoming Familiar with the Remote Control .................................................
Inserting the Batteries in the Remote Control................................................
Assembling the Stand-Base ..........................................................................
Installing the Display on the Wall Attachment Panel .....................................
Installing the Display Vertically ......................................................................
Before Using the Video Wall and the Multiple Display Contol function .........
Connecting Speakers ....................................................................................
Switching On and Off.....................................................................................
Choosing Your Language..............................................................................
12
14
15
15
16
18
18
19
21
21
◆ USING YOUR DISPLAY
■
■
■
■
■
■
■
■
■
■
■
■
10
Selecting the Color System (Video or S-Video Mode)...................................
Changing the Picture Mode ...........................................................................
Adjusting the Picture Settings........................................................................
Adjusting the Picture Settings (PC or DVI Mode) ..........................................
Selecting the Picture Size..............................................................................
Activating/Deactivating the Digital Noise Reduction Feature ........................
Freezing the Current Picture .........................................................................
Changing the Sound Mode............................................................................
Adjusting the Sound Settings ........................................................................
Extra Sound Settings.....................................................................................
- Auto Volume
- Melody
- Pseudo Stereo / Virtual Surround
Adjusting the Screen Position and Scale.......................................................
Adjusting the Image Preferences (PC Mode) ................................................
22
22
23
24
25
25
26
26
27
28
29
30
D61A-BN68-00492A-00_ENG
2003.11.18
9:31 AM
Page 11
ENG
Contents (continued)
◆ USING YOUR DISPLAY (CONTINUED)
■
■
■
■
■
■
■
■
■
■
■
■
Locking the Control buttons...........................................................................
Setting the MDC (Multiple Display Control) ...................................................
Protecting the Screen Burning.......................................................................
Setting the Multiple Screen............................................................................
Displaying the PC Information .......................................................................
Displaying the Setting Information.................................................................
Setting and Displaying the Current Time.......................................................
Switching On and Off Automatically ..............................................................
Turning On the Fan .......................................................................................
Setting the Film Mode....................................................................................
Viewing the Picture In Picture (PIP) ..............................................................
Listening to the Sound of the Sub Picture .....................................................
31
31
32
33
34
34
35
36
37
37
38
40
◆ ADDITIONAL INFORMATION AND CONNECTIONS
■
■
■
■
■
■
■
■
■
■
Viewing Pictures From External Sources ......................................................
Connecting to the Audio/Video Input .............................................................
Connecting to the S-Video Input....................................................................
Connecting to the DVD/DTV RECEIVER Input .............................................
Connecting to the DVI Input ..........................................................................
Connecting to the RGB(PC) Input .................................................................
Setting up Your PC Software (Windows only) ...............................................
Pin Configurations .........................................................................................
Input Mode (PC/DVI) .....................................................................................
Power Saver (PC1 mode only) ......................................................................
40
41
42
42
43
43
44
45
46
47
◆ RECOMMENDATIONS FOR USE
■
■
■
Troubleshooting: Before Contacting Service Personnel................................
Care and Maintenance ..................................................................................
Technical Specifications ................................................................................
Symbols
Press
☛
➢
Important
Note
11
48
48
49
D61A-BN68-00492A-00_ENG
2003.11.18
9:31 AM
Page 12
Your New Plasma Display Panel
➢
ENG
The actual configuration on your PDP may be different,
depending on your model.
Front Panel
PPM42S3/PPM50H3
a
b
c
Speaker
Speaker
PPM63H3
a
a
b
c
b
Power Indicator
- Power Off; Red
- Power On; Off
- Timer On; Green
SOURCE
- External input selection.
- Store your settings in the menu.
- When the Main menu is displayed on screen,
the Main menu is not operated with source key.
MENU
c
Menu display and exit.
Remote Control Signal Receiver
- VOL +
Aim the remote control towards this spot on the
PDP.
- Volume adjustment.
- Adjust an option value respectively.
(VOL + : Enter to the selected menu.)
▼ SEL ▲
Control the cursor in the menu.
I/
Press to turn the PDP on and off.
12
D61A-BN68-00492A-00_ENG
2003.11.18
9:31 AM
Page 13
Your New Plasma Display Panel
➢
The actual configuration on your PDP may be different,
depending on your model.
ENG
Rear Panel
➢
For further details about connection, refer to pages 41~43.
a
b
c
d
e
a) RS232C
- IN : Used for the MDC function when connecting
PC or RS232C output of another PDP.
- OUT : Used for the MDC function when
connecting with RS232C input of another
PDP.
f
g
h
j
i
f) VIDEO IN
Video and audio inputs for external devices, such as
VCR, DVD, video game device or video disc players
(or for external devices with an S-Video output;
S-VIDEO).
g) COMPONENT1 IN
b) DVI IN
Connect to the video output jack for device with
DVI output.
Video (Y/Pb/Pr) and audio (L/R) inputs for
component.
h) VIDEO OUT (VIDEO / L-AUDIO-R)
c) AUDIO
Connect to the audio output jack on your PC or any
device with DVI output. (It is audio input for b, d,
and e.)
Used to output screen of Video or S-Video in PDP
when connecting video and/or audio input of
external devices.
i) EXT SPEAKER (8Ω)
d) RGB1(PC1) IN
Connect external speakers.
Connect to the video output jack on your PC.
j) POWER IN
e) COMPONENT2/RGB2(PC2) IN
Connect the supplied power cord.
Connect for input of an Analog RGB or Y/Pb/Pr
video signal from in PC, DVD, or HD devices.
➢
“PC Mode” from this page onward means
PC1/PC2 mode using RGB1(PC1) and
RGB2(PC2).
13
D61A-BN68-00492A-00_ENG
2003.11.18
9:31 AM
Page 14
Becoming Familiar with the Remote Control
ENG
The remote control is used mainly to:
◆ Change sources and adjust the volume
◆ Set up the PDP using the on-screen menu system
PDP ON
PDP OFF
SOUND MODE SELECTION
PICTURE MODE SELECTION
CURRENT TIME DISPLAY
NUMERIC BUTTONS
PICTURE STILL
VOLUME INCREASE
TEMPORARY SOUND SWITCH-OFF
➣ Press it again , or - /+ button
to turn the sound back on.
VOLUME DECREASE
SETTING THE TIMER
DISPLAY AND CLOSE THE MENU/
RETURN TO THE PREVIOUS MENU
ZOOM/PANNING MENU DISPLAY
(ONLY PC MODE)
NEXT CHANNEL
(NOT AVAILABLE FOR THIS MONITOR)
EXTERNAL INPUT SELECTION
PREVIOUS CHANNEL
(NOT AVAILABLE FOR THIS MONITOR)
INFORMATION DISPLAY
EXIT FROM ANY DISPLAY
MOVE TO THE REQUIRED MENU
OPTION/
ADJUST AN OPTION VALUE
RESPECTIVELY
CHANGE CONFIRMATION
SCREEN EFFECT SELECTION
(BURNING PROTECTION)
MULTIPLE DISPLAY CONTROL
AUTO ADJUSTMENT IN PC MODE
PICTURE SIZE SELECTION
PIP FUNCTIONS;
- PIP ON/OFF
- SIZE SELECTION (SIZE)
- LOCATION SELECTION (LOCATE)
- INPUT SOURCE SELECTION
(SOURCE)
- INTERCHANGE THE MAIN AND THE
SUB PICTURE (SWAP)
- SOUND SELECTION (S.SEL)
➢
14
The performance of the remote control may be affected by bright light.
D61A-BN68-00492A-00_ENG
2003.11.18
9:31 AM
Page 15
Inserting the Batteries in the Remote Control
ENG
You must insert or replace the batteries in the remote control when
you:
◆ Purchase the PDP
◆ Find that the remote control is no longer operating
correctly
1
Remove the cover on the rear of the remote control by pressing
the symbol downwards and then pulling firmly to remove it.
2
Insert two R03, UM4, “AAA” 1.5V or equivalent batteries taking
care to respect the polarities:
◆ - on the battery against - on the remote control
◆ + on the battery against + on the remote control
3
Replace the cover by aligning it with the base of the remote
control and pressing it back into place.
Assembling the Stand-Base
Fit the Stand-Base into the guide hole on the bottom of
the monitor and tighten the left and right sides using
four screws for each side.
➢
◆ Two or more people should carry the PDP.
Never lay the PDP on the floor because of
possible damage to the screen. Always store the
PDP upright.
◆ For the PPM63H3 model, please see the
instruction for the SMM6330 stand.
15
D61A-BN68-00492A-00_ENG
2003.11.18
9:31 AM
Page 16
Installing the Display on the Wall Attachment Panel
ENG
☛
This wall mount bracket installation guide is for the following models: WMN4230/WMN5030/WMN6330.
This installation guide may be different from the PDP User’s manual. Please refer to the proper
installation guide for your product.
Installation Notes
◆ Do not install the PDP on any place other than vertical walls.
◆ To protect the performance of the PDP and prevent troubles, avoid the followings:
- Do not install next to smoke and fire detectors.
- Do not install in an area subjected to vibration or high voltage.
- Do not install near or around any heating apparatus.
◆ Use only recommended parts and components.
Mounting Kits
Wall Mount Bracket
PPM42S3/PPM50H3
Plastic Hanger
PPM63H3
Screws
PPM42S3/PPM50H3: 4
PPM63H3: 6
How to Adjust Mounting Angle
(depending on your model)
The wall mount bracket is delivered
separately. Please tighten the captive
screw in the direction of the arrow after
assembling the bracket.
16
1
Secure the PDP to the wall mount bracket.
(Please refer to the following instructions.)
2
Set the angle by pulling the upper end of the
PDP attached to bracket in the direction of the
arrow.
3
The angle can be adjusted from 0° to 20° by
±2°.
D61A-BN68-00492A-00_ENG
2003.11.18
9:32 AM
Page 17
Installing the Display on the Wall Attachment Panel
➢
1
The exterior of the PDP may be different than the picture.
(Assembly and installation of the plastic hanger is the same.)
Remove the screws from the back of the PDP.
PPM42S3
2
PPM63H3
◆ Please ask the installers to install the wall mount bracket.
◆ Please be sure to check if the plastic hanger is completely secured on both the left and right
side after hanging the PDP on the wall mount bracket.
◆ Please avoid catching your fingers while installing and adjusting the angle.
◆ Please tightly secure the wall mount bracket to the wall to avoid injury from a falling PDP.
Tighten the screws of the plastic hanger to the back side of the PDP.
PPM42S3
4
PPM50H3
Use the screws and assemble the plastic hanger.
☛
3
ENG
PPM50H3
PPM63H3
Put the 4 pegs on the PDP in the grooves of the wall mount bracket and pull down on the PDP (!) to
secure it to the wall mount bracket (@). Tighten the screws as shown (#) so that the PDP cannot be
separated from wall mount bracket.
PDP panel
Wall
Wall attachment panel bracket
17
D61A-BN68-00492A-00_ENG
2003.11.18
9:32 AM
Page 18
Installing the Display Vertically
ENG
You can install the PDP vertically. (PPM42S3/50H3/63H3 models
are available. Other manufacturers do not guarantee a reliably
working.) In this case, the fan automatically works. If you wish to
stop the fan, position the PDP horizontally and then set
“Selectable Fan” to “Off” in the “Function” menu.
Please use the wall attachment panel exclusively when installing
vertically. And you have to put left side of the PDP on top when
viewed from front.
Before Using the Video Wall and the Multiple Display Contol function
Example for 2x2 Video Wall function
1
Please create ID for each PDP before installing
them close together. It may be difficult to create
IDs when operating the remote control for PDPs
that are installed close to each other.
2
Press the MDC button on the remote control.
Select ID input on the menu. Use the numeric
buttons to enter the ID for PDP adjustment.
You can operate the remote control only for the
PDP that has been selected.
➢
◆ For details about Video Wall configuration
and operation, refer to “Setting the Multiple
Screen” on page 33.
◆ For details about Multiple Display Control,
refer to “Setting the MDC (Multiple Display
Control)” on page 31 and the Help section in
MDC program CD.
18
Example for Multiple Display Control connections
D61A-BN68-00492A-00_ENG
2003.11.18
9:32 AM
Page 19
Connecting Speakers
ENG
1
Remove the screws on the rear of the PDP.
PPM42S3
PPM50H3
PPM63H3
2
Hang the two “T” shaped hangers
on the square holes on the rear of
the PDP.
3
Tighten the PDP and the speaker bracket using the screws removed from the PDP.
PPM42S3
➢
PPM42S3
PPM50H3
PPM50H3
PPM63H3
PPM63H3
When moving your PDP, do NOT hold the speaker connected to your PDP. It may damage the
bracket clamping the speaker and your PDP together and result in a drop of your PDP and a risk of
personal damage and injury.
19
D61A-BN68-00492A-00_ENG
2003.11.18
9:32 AM
Page 20
Connecting Speakers (continued)
ENG
Connect the speaker audio cable to the external speaker output jack on the rear of the PDP matching
the “+” and “-” ends of the cable with the diagram on the PDP.
PPM42S3/PPM50H3
PPM63H3
➢
◆ The speakers MUST have to a power handling capability of 10 watts minimum
(impedance 8Ω).
◆ When you connect the speaker wire to the external speaker out connector, first bind the
speaker wire round the ferrite core to secure it.
Ferrite Cores
The ferrite cores are used to attenuate undesired signals.
When connecting cables, attach one of these ferrite cores to the cable
near the connector.
20
D61A-BN68-00492A-00_ENG
2003.11.18
9:32 AM
Page 21
Switching On and Off
ENG
The mains lead is attached to the rear of your PDP.
☛
1
If you have purchased this PDP in the United Kingdom,
refer to page 9 for further instructions on plug wiring.
Front of the PDP
Plug the mains lead into an appropriate socket.
Result:
➢
The Standby indicator on the front of the PDP lights up.
The main voltage is indicated on the rear of the PDP and
the frequency is 50 or 60Hz.
2
Press the “ I / ” button on the front of the PDP (or ON (
button on the remote control) to switch the PDP on.
3
To switch your PDP off, press the “ I /
button on the remote control).
)
” button again (or OFF
Choosing Your Language
When you start using your PDP for the first time, you must select the
language which will be used for displaying menus and indications.
1
Press the MENU button.
Result:
2
Language
English
Time
√
Selectable Fan
œ Off √
Film Mode
œ Off √
Press the ▲ or ▼ button to select Function.
Result:
3
The main menu is displayed.
Function
The options available in the Function group are
displayed.
Move
Press the √ button.
Result:
Enter
Language
The Language option is selected.
English
4
Press the √ button again.
Français
Result:
Deutsch
The languages available are listed.
Italiano
5
6
Select the appropriate language by pressing the ▲ or ▼ button
repeatedly.
Press the
Español
Sel.
Store
button to confirm your choice.
21
Return
D61A-BN68-00492A-00_ENG
2003.11.18
9:32 AM
Page 22
Selecting the Color System (Video or S-Video Mode)
➢
ENG
If necessary, select the broadcasting standard which best
corresponds to your viewing requirements.
Picture
Color System
œ AUTO √
Mode
œ Dynamic √
Adjust
√
Color Tone
œ Normal √
Size
Wide
Digital NR
œ Off √
Move
Sel.
Preset to the Video or S-Video mode by using the SOURCE button.
1
Press the MENU button.
Result:
2
Return
Press the √ button.
Result:
3
The options available in the Picture group are
displayed.
The Color System is selected.
Select a required color system by pressing the œ or √ button.
Result:
The following color systems are available.
AUTO - PAL - SECAM - NTSC4.43 - NTSC3.58 PAL M - PAL N - PAL60
Changing the Picture Mode
You can select the type of picture which best corresponds to your
viewing requirements.
Picture
Mode
œ Dynamic √
Adjust
√
Color Tone
œ Normal √
Size
Wide
Digital NR
œ Off √
Move
Sel.
1
Press the MENU button.
Result:
The options available in the Picture group are
displayed.
2
Press the √ button.
3
Press the ▲ or ▼ button to select Mode. Select the option by
pressing the œ or √ button.
Return
Result:
The following modes are available depending on the
input source.
◆ Dynamic - Standard - Movie - Custom
◆ Custom - High - Middle - Low
(PC or DVI Mode)
➣
22
You can also set these options simply by pressing the
P.MODE (Picture Mode) button.
D61A-BN68-00492A-00_ENG
2003.11.18
9:32 AM
Page 23
Adjusting the Picture Settings
ENG
Your PDP has several settings which allow you to control picture
quality.
1
Press the MENU button.
Result:
The options available in the Picture group are
displayed.
2
Press the √ button.
3
Press the ▲ or ▼ button to select Adjust. Press the √ button.
Picture
Mode
œ Dynamic √
Adjust
√
Color Tone
œ Normal √
Size
Wide
Digital NR
œ Off √
Move
Result:
4
The Adjust menu is displayed.
The horizontal bar is displayed. Move the horizontal
bar’s cursor left or right by pressing the œ or √ button.
5
When you are satisfied with the settings, press the
store them.
6
Press the MENU button.
Result:
7
button to
The options available in the Picture group are
displayed again.
Press the ▲ or ▼ button to select Color Tone. Select the option
by pressing the œ or √ button. The color tones are displayed in
the following order.
Normal - Warm1 - Warm2 - Cool2 - Cool1
➣
Return
Adjust (Dynamic)
Press the ▲ or ▼ button to select the option (Contrast,
Brightness, Sharpness, Color, Tint-NTSC only) to be
adjusted. Press the œ or √ button.
Result:
Enter
Contrast
100
Brightness
45
Sharpness
75
Color
55
Move
Adjust
Store
Picture
Mode
œ Dynamic √
Adjust
√
Color Tone
œ Normal √
Size
Wide
Digital NR
œ Off √
Move
Enter
If you make any changes to these settings, the picture
mode is automatically switched to the Custom.
23
Return
D61A-BN68-00492A-00_ENG
2003.11.18
9:32 AM
Page 24
Adjusting the Picture Settings (PC or DVI Mode)
➢
ENG
1
Picture
Preset to the PC or DVI mode by using the SOURCE button.
Press the MENU button.
Result:
Mode
œ Custom √
Adjust
√
Color Tone
œ Custom √
Color Adjust
√
Size
Wide
2
Press the √ button.
3
Press the ▲ or ▼ button to select Adjust. Press the √ button.
Result:
Move
Enter
Adjust (Custom)
75
Brightness
60
Sharpness
50
Picture
œ Custom √
Adjust
√
Color Tone
œ Custom √
√
Size
Wide
Move
When you are satisfied with the settings, press the
store them.
6
Press the MENU button.
Sel.
Result:
7
Mode
Return
√
Color Tone
œ Custom √
Color Adjust
√
Size
Wide
Press the ▲ or ▼ button to select color Adjust. Press the √
button.
➣
œ Custom √
Enter
◆ The Color Adjust menu can not be selected in DVI
mode.
9
Return
10
Color Adjust
Red
50
Green
50
Blue
50
Move
Adjust
24
Store
The Color Adjust menu is displayed.
◆ When select the Color Tone to Custom, the Color
Adjust menu is displayed.
Press the ▲ or ▼ button to select the option (Red, Green, Blue) to
be adjusted. Press the œ or √ button.
Result:
Move
The options available in the Picture group are
displayed again.
Press the ▲ or ▼ button to select Color Tone. Select the option
by pressing the œ or √ button. The color tones are displayed in
the following order.
Result:
Picture
Adjust
button to
Custom (PC mode only) - Color1 - Color2 - Color3
8
Mode
The horizontal bar is displayed. Move the horizontal
bar’s cursor left or right by pressing the œ or √ button.
5
Store
Color Adjust
Press the ▲ or ▼ button to select the option (Contrast,
Brightness, Sharpness) to be adjusted. Press the œ or √ button.
Result:
Contrast
Adjust
The Adjust menu is displayed.
Return
4
Move
The options available in the Picture group are
displayed.
The horizontal bar is displayed. Move the horizontal
bar’s cursor left or right by pressing the œ or √ button.
When you are satisfied with the settings, press the
store them.
button to
D61A-BN68-00492A-00_ENG
2003.11.18
9:32 AM
Page 25
Selecting the Picture Size
ENG
You can select the picture size which best corresponds to your
viewing requirements.
1
Press the MENU button.
Result:
The options available in the Picture group are
displayed.
2
Press the √ button.
3
Press the ▲ or ▼ button to select Size. Press the √ button.
4
Select the option by pressing the œ or √ button.
The following modes are available depending on the
Result:
input source.
Picture
Mode
œ Dynamic √
Adjust
√
Color Tone
œ Normal √
Size
Wide
Digital NR
œ Off √
Move
◆ Wide - Zoom1 - Zoom2 - 14:9 - Normal
Sel.
Return
Size
Wide
œ √ Sel.
Store
◆ Wide - Panorama (Video or S-Video Mode) Zoom1 - Zoom2 - 14:9 - Normal
The lifting is available in the Zoom1, Zoom2 or
14:9 mode by pressing the † or … button.
➣
◆ Wide - Normal
(PC or DVI Mode)
➣
You can also set these options simply by pressing the
P.SIZE button.
Activating/Deactivating the Digital Noise Reduction Feature
If the signal received by your PDP is weak, you can activate this
feature to reduce any static and ghosting that may appear on the
screen.
1
Press the MENU button.
Result:
The options available in the Picture group are
displayed.
2
Press the √ button.
3
Press the ▲ or ▼ button to select Digital NR.
4
Press the œ or √ button to change the setting (On or Off).
Picture
Mode
œ Dynamic √
Adjust
√
Color Tone
œ Normal √
Size
Wide
Digital NR
œ Off √
Move
Sel.
25
Return
D61A-BN68-00492A-00_ENG
2003.11.18
9:32 AM
Page 26
Freezing the Current Picture
ENG
You can freeze the picture when watching a moving picture simply
by pressing the “STILL” button. To return to normal viewing, press
it again.
➣
In the PIP mode, the main and sub pictures are stilled at
the same time.
Changing the Sound Mode
You can select the type of special sound effect to be used when
watching a given broadcast.
Sound
Mode
œ Custom √
Equalizer
√
Auto Volume
œ Off √
Melody
œ Off √
Pseudo Stereo
œ Off √
Virtual Surround
œ Off √
Move
Sel.
1
Press the MENU button.
Result:
2
Press the ▲ or ▼ button to select Sound.
Result:
Return
3
The options available in the Sound group are displayed.
Press the √ button.
Result:
4
The main menu is displayed.
The Mode is selected.
Select the option by pressing the œ or √ button. The sound effects
are displayed in the following order.
Custom - Standard - Music - Movie - Speech
➣
26
You can also set these options simply by pressing the
S.MODE (Sound Mode) button.
D61A-BN68-00492A-00_ENG
2003.11.18
9:32 AM
Page 27
Adjusting the Sound Settings
ENG
The sound settings can be adjusted to suit your personal
preferences.
1
Press the MENU button.
Result:
2
Sound
The main menu is displayed.
Press the ▲ or ▼ button to select Sound.
Result:
Press the √ button.
4
Press the ▲ or ▼ button to select Equalizer. Press the √ button.
5
6
The Equalizer menu is displayed with the current
option.
Select the option (volume, balance, equalizer) to be adjusted by
pressing the œ or √ button. Press the ▲ or ▼ button to reach the
required setting.
When you are satisfied with the settings, press the
store them.
➣
œ Custom √
Equalizer
√
Auto Volume
œ Off √
Melody
œ Off √
Pseudo Stereo
œ Off √
Virtual Surround
œ Off √
The options available in the Sound group are displayed.
3
Result:
Mode
Move
Enter
Return
Equalizer (Custom)
10
R
L
100 300
œ √ Move
Adjust
button to
If you make any changes to the equalizer settings, the
sound mode is automatically switched to the Custom.
27
1K
3K
10K
Store
D61A-BN68-00492A-00_ENG
2003.11.18
9:32 AM
Page 28
Extra Sound Settings
ENG
◆ Auto Volume
Each broadcasting station has its own signal conditions,
and so it is not easy for you to adjust the volume every
time the channel is changed. This feature lets you
automatically adjust the volume of the desired channel by
lowering the sound output when the modulation signal is
high or by raising the sound output when the modulation
signal is low.
Sound
Mode
œ Custom √
Equalizer
√
Auto Volume
œ Off √
Melody
œ Off √
Pseudo Stereo
œ Off √
Virtual Surround
œ Off √
Move
Sel.
Return
◆ Melody
You can hear clear melody sound when the PDP is
powered on or off.
Sound
Mode
œ Custom √
Equalizer
√
Auto Volume
œ Off √
Melody
œ Off √
Pseudo Stereo
œ Off √
Virtual Surround
œ Off √
Move
Sel.
◆ Pseudo Stereo / Virtual Surround
Pseudo stereo feature converts a monaural sound
signal into two identical left and right channels.
Once the Pseudo stereo or Virtual surround is set
to On or Off, these settings apply to the sound effects
such as Standard, Music, Movie, and Speech.
Return
Sound
Mode
œ Custom √
Equalizer
√
Auto Volume
œ Off √
Melody
œ Off √
Pseudo Stereo
œ Off √
Virtual Surround
œ Off √
Move
Sel.
Mode
œ Custom √
Equalizer
√
Auto Volume
œ Off √
Melody
œ Off √
Pseudo Stereo
œ Off √
Virtual Surround
œ Off √
Sel.
28
Press the MENU button.
Result:
2
The main menu is displayed.
Press the ▲ or ▼ button to select Sound.
Result:
The options available in the Sound group are displayed.
Return
Sound
Move
1
Return
3
Select the required option (Auto Volume, Melody, Pseudo
Stereo, Virtual Surround) by pressing the ▲ or ▼ button.
4
Press the œ or √ button to change the setting (Off or On).
D61A-BN68-00492A-00_ENG
2003.11.18
9:32 AM
Page 29
Adjusting the Screen Position and Scale
ENG
1
Press the MENU button.
Result:
2
3
Screen Adjust
√
Press the ▲ or ▼ button to select Setup.
Key Lock
œ Off √
Multi Control
√
Result:
Burning Protection
√
Video Wall
√
The options available in the Setup group are displayed.
Press the √ button.
Result:
4
Setup
The main menu is displayed.
The Screen Adjust is selected.
Move
Enter
Return
Press the √ button again.
Result:
The Screen Adjust menu is displayed with the
Position selected.
5
Press the √ button over again. Adjust the screen position by
pressing the ▲, ▼, œ, or √ button.
6
When you are satisfied with the setting, press the
store.
7
Press the MENU button.
Result:
button to
Position
√
Scale
√
Reset
√
√ Enter
Move
Return
Position
The Screen Adjust menu is displayed again.
8
Press the ▲ or ▼ button to select Scale. Press the √ button.
Adjust the screen scale by pressing the ▲, ▼, œ, or √ button.
9
When you are satisfied with the setting, press the
store
➣
Screen Adjust
Adjust
Store
button to
Press the ▲ or ▼ button to select Reset. Press the √ button.
The position and scale settings are replaced with the factory
default values.
Screen Adjust
Position
√
Scale
√
Reset
√
√ Enter
Move
Return
Scale
Adjust
Store
Screen Adjust
Position
√
Scale
√
Reset
√
Move
√ Enter
29
Return
D61A-BN68-00492A-00_ENG
2003.11.18
9:32 AM
Page 30
Adjusting the Image Preferences (PC Mode)
ENG
Setup
Image Lock
√
Key Lock
œ Off √
Multi Control
√
Burning Protection
√
Video Wall
√
Information
√
Move
Enter
1
Press the MENU button.
The main menu is displayed.
Result:
2
Press the ▲ or ▼ button to select Setup.
The options available in the Setup group are displayed.
Result:
3
Press the √ button.
The Image Lock is selected.
Result:
4
Press the √ button again.
The Image Lock menu is displayed with the Auto
Result:
Adjustment selected.
5
Press the √ button over again.
The screen size and frequency are automatically reset
Result:
with the Auto Adjustment displayed.
Return
Image Lock
Auto Adjustment
√
Frequency
√
Phase
√
Position
√
Zoom/Panning
√
√ Enter
Move
➣
Return
6
Press the ▲ or ▼ button to select Frequency (or Phase). Press
the √ button.
The horizontal bar is displayed. Move the horizontal
Result:
bar’s cursor left or right by pressing the œ or √ button.
7
When you are satisfied with the settings, press the MENU button.
The Image Lock menu is displayed again.
Result:
8
Press the ▲ or ▼ button to select Position. Press the √ button.
Adjust the screen position by pressing the ▲, ▼, œ, or √ button.
9
When you are satisfied with the setting, press the
store.
10
Press the MENU button.
The Image Lock menu is displayed again.
Result:
11
Press the ▲ or ▼ button to select Zoom/Panning. Press the √
button.
The Zoom/Panning menu is displayed with the Zoom
Result:
selected.
Frequency
0
œ √ Adjust
Return
Position
Adjust
Store
Zoom/Panning
Zoom
1
Panning
√
Reset
√
œ √ Adjust
Move
Return
➣
Zoom/Panning
Zoom
1
Panning
√
Reset
√
√ Enter
Move
13
Press the ▲ or ▼ button to select Panning. Move the magnified
picture to required position by using pressing the ▲, ▼, œ, or √
button.
➢
1
√
Reset
√
Move
√ Enter
30
➢
Return
You can also do simpley by pressing the ZOOM button.
Press the œ or √ button to reach the required magnification.
Zoom/Panning
Panning
button to
12
Return
Zoom
You can also do simply by pressing the AUTO button.
Press the ▲ or ▼ button to select Reset. Press the √ button.
The zoom and panning settings are replaced with the factory
default values.
The Panning and Reset menus can be used when value of
Zoom is more than 1.
D61A-BN68-00492A-00_ENG
2003.11.18
9:32 AM
Page 31
Locking the Control buttons
ENG
This feature allows you to lock the PDP so that it cannot be
switched on via the front panel. It can, however, still be switched
on via the remote control. Thus, by keeping the remote control
away from unauthorised users.
1
Press the MENU button.
Result:
2
The main menu is displayed.
Setup
Screen Adjust
√
Key Lock
œ Off √
Multi Control
√
Burning Protection
√
Video Wall
√
Press the ▲ or ▼ button to select Setup.
Result:
Move
Sel.
Return
The options available in the Setup group are displayed.
3
Press the √ button.
4
Press the ▲ or ▼ button to select Key Lock.
5
Press the œ or √ button to change the setting (On or Off).
Setting the MDC (Multiple Display Control)
1
Press the MENU button.
Result:
2
The main menu is displayed.
Setup
Screen Adjust
√
Press the ▲ or ▼ button to select Setup.
Key Lock
œ Off √
Multi Control
√
Result:
Burning Protection
√
Video Wall
√
The options available in the Setup group are displayed.
3
Press the √ button.
4
Press the ▲ or ▼ button to select Multi Control.
5
Press the √ button.
Result:
The Multi Control menu is displayed with the ID
Setup selected.
Move
Enter
Multi Control
ID Setup
01
ID Input
6
Select the ID setup number by pressing the œ or √ button.
7
Press the ▲ or ▼ button to select ID Input. Enter ID input
number by using the numeric buttons.
➢
➢
To operate the multi control function, PDP1 and PDP2 should be
set in the ID Setup mode. When entering the ID Input number of
PDP1 while the PDP is set in the ID Input mode, only PDP1 is
switched to the Menu screen and you can operate the remote
control. At this time, PDP2 doesn't operate with the remote control
and displays the standby mode of ID Input.
Return
-œ √ Adjust
Move
Return
Multi Control
ID Setup
01
ID Input
--
Enter ID Input Number
For further details, refer to the MDC program guide.
31
D61A-BN68-00492A-00_ENG
2003.11.18
9:32 AM
Page 32
Protecting the Screen Burning
ENG
You can prevent the residual image of the PDP.
Setup
1
Screen Adjust
√
Key Lock
œ Off √
Multi Control
√
Burning Protection
√
Video Wall
√
Press the MENU button.
Result:
2
Press the ▲ or ▼ button to select Setup.
Result:
Move
Enter
Return
The main menu is displayed.
The options available in the Setup group are displayed.
3
Press the √ button.
4
Press the ▲ or ▼ button to select Burning Protection.
5
Press the √ button.
Burning Protection
Pixel Shift
√
Signal Pattern
œ Off √
All White
œ Off √
√ Enter
Move
Return
Result:
6
Press the √ button again.
Result:
Pixel Shift
➣
œ On √
Set
Horizontal Dot
2
Vertical Line
4
Time
4 MIN
œ √ Sel.
Move
Return
Signal Pattern
œ Off √
8
Select the option (Horizontal Dot, Vertical Line, Time) to be
adjusted by pressing the ▲ or ▼ button. Press the œ or √ button
to reach the required setting.
œ √ Sel.
Move
Return
9
Burning Protection
√
Signal Pattern
œ Off √
All White
œ Off √
œ √ Sel.
Return
PPM50/63H3
4
4
4MIN
The Burning Protection menu is displayed again.
10
Press the ▲ or ▼ button to select Signal Pattern. Set to On by
pressing the œ or √ button for removing the residual image.
11
Press the ▲ or ▼ button to select All White. Set to On by
pressing the œ or √ button for removing the residual image after
making the screen white.
➣
32
PPM42S3
2
4
4MIN
When you are satisfied with the settings, press the MENU button.
Result:
Pixel Shift
Move
Optimum condition for pixel shift;
Horizontal Dot
Vertical Line
Time
œ Off √
All White
You can also do simply by pressing the S.EFFECT button.
Set to On by pressing the œ or √ button for making the screen
move per regular hour and preventing the residual image.
➣
√
The Pixel Shift menu is displayed with the Set
selected.
7
Burning Protection
Pixel Shift
The Burning Protection menu is displayed with
the Pixel Shift selected.
The Signal Pattern and All White feature are
effective after working for a long time.
D61A-BN68-00492A-00_ENG
2003.11.18
9:32 AM
Page 33
Setting the Multiple Screen
ENG
You can get the various display effect with many PDPs.
Setup
1
Press the MENU button.
Result:
2
The main menu is displayed.
Press the ▲ or ▼ button to select Setup.
Result:
Screen Adjust
√
Key Lock
œ Off √
Multi Control
√
Burning Protection
√
Video Wall
√
The options available in the Setup group are displayed.
3
Press the √ button.
4
Press the ▲ or ▼ button to select Video Wall.
5
Press the √ button.
Move
Enter
Return
Video Wall
Result:
The Video Wall menu is displayed with the Set
selected.
6
Set to On by pressing the œ or √ button.
7
Press the ▲ or ▼ button to select Screen Divider. Press the √
button.
8
Select the option (2x2, 3x3, 4x4, 1x5, 5x1) by pressing the ▲ or
▼ button. Press the √ button.
9
Press the œ or √ button to select the position of the screens.
➣
œ On √
Set
√
Screen Divider
œ √ Sel.
Move
Return
Video Wall
Set
œ On √
Screen Divider
√
√ Enter
Move
Return
Screen Divider
2x2 √
PIP function does not operate during Video Wall
operation.
3x3
1
3
4x4
2
4
1x5
5x1
√ Enter
Move
Return
Screen Divider
2x2 √
3x3
1
3
4x4
2
4
1x5
5x1
œ √ Sel.
Return
33
D61A-BN68-00492A-00_ENG
2003.11.18
9:32 AM
Page 34
Displaying the PC Information
ENG
1
Setup
Image Lock
√
Key Lock
œ Off √
Multi Control
√
Burning Protection
√
Video Wall
√
Information
√
Move
Return
PC Information
60
H Frequency
48
The main menu is displayed.
Press the ▲ or ▼ button to select Setup.
The options available in the Setup group are displayed.
3
Press the √ button.
4
Press the ▲ or ▼ button to select Information.
5
Press the √ button.
Result:
1024x768
V Frequency
2
Result:
Enter
Resolution
Press the MENU button.
Result:
The resolution, vertical frequency and horizontal
frequency are displayed.
Return
Displaying the Setting Information
You can view the setting status you select by pressing the “INFO”
button on the remote control.
Mode
Picture
Sound
Clock
Video
Dynamic
Custom
11:45
34
D61A-BN68-00492A-00_ENG
2003.11.18
9:32 AM
Page 35
Setting and Displaying the Current Time
ENG
You can set the clock so that the current time is displayed. You must
also set the time if you wish to use the automatic on or off timers.
1
Press the MENU button.
Result:
2
The main menu is displayed.
Press the √ button.
4
Press the ▲ or ▼ button to select Time. Press the √ button.
Result:
➣
√
Selectable Fan
œ Off √
Film Mode
œ Off √
The Time menu is displayed with the Clock option
selected.
You can also do simply by pressing the TIMER button.
Enter
Clock Display
œ Off √
Timer
œ Off √
On Time Volume
--:--
Off Time
--:-œ √ Sel.
button to
Store
Time
11:35
Clock
Clock Display
œ Off √
Timer
œ Off √
On Time Volume
You can also do simply by pressing the CLOCK DISPLAY
button.
10
On Time
Set the clock first! If you have not yet set the clock, you can
not set other options of the Time menu.
When you are satisfied with the settings, press the
store them.
Return
11:35
Clock
Move
Press the ▲ or ▼ button to select Clock Display.
Set to On by pressing the œ or √ button for displaying the current
time.
➣
Move
Time
Press the œ or √ button to move to the hour or minute.
Set the hour or minute by pressing the ▲ or ▼ button.
➣
7
English
Time
The options available in the Function group are
displayed.
3
6
Language
Press the ▲ or ▼ button to select Function.
Result:
5
Function
10
On Time
--:--
Off Time
--:--
Move
œ √ Sel.
35
Store
D61A-BN68-00492A-00_ENG
2003.11.18
9:32 AM
Page 36
Switching On and Off Automatically
ENG
You can set the on or off time so that the PDP will:
◆ Switch on automatically and tune to the volume of your
choice at the time you select
Time
11:35
Clock
Clock Display
œ Off √
Timer
œ Off √
On Time Volume
10
On Time
--:--
Off Time
--:--
Move
◆ Switch off automatically at the time you select
œ √ Sel.
1
Result:
Store
2
Clock Display
œ Off √
Timer
œ Off √
On Time Volume
10
On Time
--:--
Off Time
--:-œ √ Adjust
3
Press the √ button.
4
Press the ▲ or ▼ button to select Time. Press the √ button.
Result:
➣
Store
11:35
Clock
Clock Display
œ Off √
Timer
œ Off √
On Time Volume
06:00
Off Time
--:-œ √ Sel.
Press the ▲ or ▼ button to select Timer. Set to On by pressing the
œ or √ button for switching on or off automatically.
6
Press the ▲ or ▼ button to select On Time Volume. Set the
volume by pressing the œ or √ button for tuning to the volume of
your choice at the time switching on.
7
Press the ▲ or ▼ button to select On Time. Press the œ or √
button to move to the hour or minute. Set the time at which you
wish the PDP to be switched on automatically by pressing the ▲
or ▼ button.
8
Press the ▲ or ▼ button to select Off Time. In the same above,
set the time at which you wish the PDP to be switched off
automatically.
9
When you are satisfied with the settings, press the
store them.
Store
Time
11:35
Clock Display
œ Off √
Timer
œ Off √
On Time Volume
10
On Time
06:00
Off Time
23:30
œ √ Sel.
You can also do simply by pressing the TIMER button.
10
On Time
Clock
The Time menu is displayed.
5
Time
Move
The options available in the Function group are
displayed.
11:35
Clock
Move
The main menu is displayed.
Press the ▲ or ▼ button to select Function.
Result:
Time
Move
Press the MENU button.
Store
➣
button to
Absent Power Off
Your PDP will automatically be turned off, if you do not
operate any controls during the 3 hours when the “Timer”
is set to “On” and the “On Time” is set. However, this
feature will not work when the “Off Time” is set.
This feature prevents a leakage accident or overheating,
caused by your PDP left on for an extended time (when
you are away on holiday, for example).
36
D61A-BN68-00492A-00_ENG
2003.11.18
9:32 AM
Page 37
Turning On the Fan
ENG
You can use the Fan if you are anxious for the PDP.
Function
1
2
Press the MENU button.
Language
English
Result:
Time
√
Selectable Fan
œ Off √
Film Mode
œ Off √
The main menu is displayed.
Press the ▲ or ▼ button to select Function.
Result:
The options available in the Function group are
displayed.
3
Press the √ button.
4
Press the ▲ or ▼ button to select Selectable Fan.
5
Press the œ or √ button to change the setting (On or Off).
➣
Move
Sel.
Return
◆ If your PDP is displayed vertically, the fan
automatically works.
◆ The message Check Fan is displayed if there is a fan
problem.
◆ Please use the fan when the temperature is over 35
degrees.
Setting the Film Mode
When a video input source is from a film such as movies, this feature
identifies the source and changes to the corresponding screen.
1
Press the MENU button.
Result:
2
The main menu is displayed.
Function
Language
English
Time
√
Selectable Fan
œ Off √
Film Mode
œ Off √
Press the ▲ or ▼ button to select Function.
Result:
The options available in the Function group are
displayed.
3
Press the √ button.
4
Press the ▲ or ▼ button to select Film Mode.
5
Press the œ or √ button to change the setting (On or Off).
➣
Move
Sel.
◆ If video source is not film, set to Off.
◆ Available in Video, S-Video, and Component (480i)
modes.
37
Return
D61A-BN68-00492A-00_ENG
2003.11.18
9:32 AM
Page 38
Viewing the Picture In Picture (PIP)
ENG
You can display a sub picture within the main picture. In this way
you can monitor the video input from any connected devices while
monitoring other video input.
PIP
PIP
œ On √
Sel.
œ Video √
Swap
√
Size
œ Large √
Locate
œ
Sound Sel.
œ Main √
Move
Sel.
1
Result:
√
2
Press the ▲ or ▼ button to select PIP.
3
Press the √ button.
Result:
PIP
œ On √
Sel.
œ Video √
Swap
√
Size
œ Large √
Locate
œ
Sound Sel.
œ Main √
Sel.
√
4
Result:
5
Return
œ On √
Sel.
œ Video √
Swap
√
Size
œ Large √
Locate
œ
Sound Sel.
œ Main √
Press the ▲ or ▼ button to select Sel.. Select a source of the sub
picture by pressing the œ or √ button.
Result:
√
➣
6
Press the ▲ or ▼ button to select Swap. Press the √ button.
PIP
œ On √
Sel.
œ Video √
Swap
√
Size
œ Large √
Locate
œ
Sound Sel.
œ Main √
√
Return
PIP
PIP
œ On √
Sel.
œ Video √
Swap
√
Size
œ Large √
Locate
œ
Sound Sel.
œ Main √
Sel.
38
Press the ▲ or ▼ button to select Size. Select a size of the sub
picture by pressing the œ or √ button.
Result:
PIP
Move
The main picture and sub picture are interchanged.
Return
7
Sel.
The sources are displayed in the following order:
For further details about selecting a source, refer to
“Selecting the source of sub picture depending on the source
of main picture” on page 39.
Result:
Move
The options available in the PIP group are displayed.
Video - S-Video - Component1 - Component2 PC1 - PC2 - DVI
PIP
Enter
The PIP option is selected.
Set to On by pressing the œ or √ button for activating the PIP
feature.
PIP
Move
The main menu is displayed.
Return
PIP
Move
Press the MENU button.
√
Return
The sizes are displayed in the following order:
Large - Small - Double1 - Double2
8
Press the ▲ or ▼ button to select Locate. Select a location of the
sub picture by pressing the œ or √ button.
D61A-BN68-00492A-00_ENG
2003.11.18
9:32 AM
Page 39
Viewing the Picture In Picture (PIP) (continued)
ENG
Easy functions of remote control.
Buttons
Feature
PIP ON
Used to activate or deactivate the PIP feature directly.
SIZE
Used to select a size of sub picture (Large, Small,
Double1, Double2).
LOCATE
Used to move the sub picture counterclockwise.
SOURCE
Used to assign a source of sub picture.
SWAP
Used to interchange the main picture and the sub
picture.
S.SEL
Used to listen the sound of the sub picture.
Selecting the source of sub picture depending on the source of main picture
Main picture
Video
S-Video
Component1
Component1
PC1
PC2
DVI
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Sub picture
Video
S-Video
✔
Component1
✔
✔
Component2
✔
✔
PC1
✔
✔
PC2
✔
✔
DVI
✔
✔
39
D61A-BN68-00492A-00_ENG
2003.11.18
9:32 AM
Page 40
Listening to the Sound of the Sub Picture
ENG
During the PIP feature is activating, you can listen to the sound of the
sub picture.
PIP
PIP
œ On √
Sel.
œ Video √
Swap
√
Size
œ Large √
Locate
œ
Sound Sel.
œ Sub √
Move
√
Sel.
1
Press the MENU button.
Result:
2
Press the ▲ or ▼ button to select PIP.
Result:
Return
The main menu is displayed.
The options available in the PIP group are displayed.
3
Press the √ button.
4
Press the ▲ or ▼ button to select Sound Sel.. Set to Sub by
pressing the œ or √ button.
Result:
➣
You can listen to the sound of the sub picture.
◆ To listen the sound of current main picture, set to Main.
◆ You can also do simply by pressing the S.SEL button.
Viewing Pictures From External Sources
Once you have connected up your various audio and video systems,
you can view different sources by selecting the appropriate input.
1
Check that all the necessary connections have been made.
2
Switch your PDP on, then press the SOURCE button.
Result:
The input sources available are displayed.
AV Input
Video
S-Video
Component1
Component2
PC1
PC2
DVI
Connected
Not Connected
Connected
Not Connected
Not Connected
Sel.
Store
3
Press the ▲ or ▼ button to select the required input source.
4
Press the
➣
button to store.
◆ If you change the external source while viewing,
pictures might take a short period of time to be
switched.
◆ Connection is not indicated for Component2 and
PC2, which use the same input connector.
40
D61A-BN68-00492A-00_ENG
2003.11.18
9:32 AM
Page 41
Connecting to the Audio/Video Input
ENG
The "VIDEO IN" connectors are used for the equipment with an Composite Video output, such as
video game devices or video disc players.
Rear of the PDP
(Input)
VCR
①
DVD
Decoder /
Video game device
Video disc player
The "VIDEO OUT" connectors are used for the equipment with an
Composite Video input, such as a camcorder or VCR.
Camcorder
Rear of the PDP
(Output)
Satellite receiver
②
① If you have a second VCR and wish to copy cassettes tape, connect the source VCR to “VIDEO IN” and
the target VCR to “VIDEO OUT” so that you can redirect the signal from “VIDEO IN” to “VIDEO OUT”.
② When you wish to record a programme, connect the receiver to “VIDEO IN” and the VCR to “VIDEO
OUT” so that you can redirect the signal from “VIDEO IN” to “VIDEO OUT”.
☛
Whenever you connect an audio or video system to your
PDP, ensure that all elements are switched off.
Refer to the documentation supplied with your equipment
for detailed connection instructions and associated safety
precautions.
41
D61A-BN68-00492A-00_ENG
2003.11.18
9:32 AM
Page 42
Connecting to the S-Video Input
ENG
The S-VIDEO and RCA (AUDIO-L/R) connectors are used for equipment with an S-Video output,
such as a camcorder or VCR.
Rear of the PDP
Camcorder
①
and
VCR
① To play picture and sound, both the S-VIDEO and RCA connectors must be used.
Connecting to the DVD/DTV RECEIVER Input
The “COMPONENT1 IN” (or “R(Pr)/G(Y)/B(Pb)” (video) and “AUDIO”) connectors are used for
equipment with a DVD/ DTV RECEIVER output. (480i, 480p, 720, 1080i)
Rear of the PDP
Y / Pb / Pr
L/R
DVD
or
Pr / Y / Pb
and
or
42
Digital Set-Top Box
D61A-BN68-00492A-00_ENG
2003.11.18
9:32 AM
Page 43
Connecting to the DVI Input
ENG
The “DVI IN” (video) and “AUDIO” connectors are used for equipment with a DVI output.
Rear of the PDP
Personal Computer
and
Connecting to the RGB(PC) Input
The “RGB1(PC1) IN” (or “R(Pr)/G(Y)/B(Pb)/H/V”) and “AUDIO”
connectors are used for interfacing with your PC.
Rear of the PDP
or
Personal Computer
43
D61A-BN68-00492A-00_ENG
2003.11.18
9:32 AM
Page 44
Setting up Your PC Software (Windows only)
ENG
The Windows display-settings for a typical computer are shown below. But the actual screens on your
PC will probably be different, depending upon your particular version of Windows and your particular
video card. But even if your actual screens look different, the same, basic set-up information will apply
in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer.)
On the windows screen, select in the following
sequence: Start ➞ Settings ➞ Control Panel.
When the control panel screen appears, click on
Display and a display dialog-box will appear.
Select the Settings tab in the display dialog-box.
The two key variables that apply the PDP-PC interface
are “Resolution” and “Colours”.
The correct settings for these two variables are:
◆ Size (sometimes called “Resolution”)
- 640 x 480 pixels (PPM42S3)
- 1024 x 768 pixels (PPM50/63H3)
◆ Colour
24-bit colour (might also be expressed as “16
million colours”)
Shown at left is a typical screen for “Display” dialog
box.
If a vertical-frequency option exists on your display
settings dialog box, the correct value is 60 Hz.
Otherwise, just click OK and exit the dialog box.
44
D61A-BN68-00492A-00_ENG
2003.11.18
9:32 AM
Page 45
Pin Configurations
ENG
RGB(PC) Input Connector
(15Pin)
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
RGB(PC) IN
Red (R)
Green (G)
Blue (B)
Grounding
Grounding (DDC)
Red (R) Grounding
Green (G) Grounding
Blue (B) Grounding
Reserved
Sync Grounding
Grounding
Data (DDC)
Horizontal sync.
Vertical sync.
Clock (DDC)
RS232C Connector
(9Pin)
Pin
1
2
3
4
5
6
7
8
9
Signal
Carrier Detect
Receive Data
Transmit Data
Data Terminal Ready
System Ground
Data Set Ready
Request to Send
Clear to Send
Ring Indicator
DVI Input Connector
(24Pin)
Pin
Signal
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
T.M.D.S. Data2T.M.D.S. Data2+
T.M.D.S. Data2/4 Shield
T.M.D.S. Data4T.M.D.S. Data4+
Clock (DDC)
Data (DDC)
Not Connected
T.M.D.S. Data1T.M.D.S. Data1+
T.M.D.S. Data1/3 Shield
T.M.D.S. Data3T.M.D.S. Data3+
+5V Power
5V Grounding
Hot Plug Detect
T.M.D.S. Data0T.M.D.S. Data0+
T.M.D.S. Data0/5 Shield
T.M.D.S. Data5T.M.D.S. Data5+
T.M.D.S. Clock Shield
T.M.D.S. Clock+
T.M.D.S. Clock-
45
D61A-BN68-00492A-00_ENG
2003.11.18
9:32 AM
Page 46
Input Mode (PC/DVI)
ENG
Both screen position and size will vary depending on the type of PC monitor and its resolution.
The table below shows all of the display modes that are supported:
Resolution
VGA
640 x 350
640 x 400
720 x 400
640 x 480
SVGA
800 x 600
XGA
1024 x 768
WVGA
848 x 480
SXGA
852 x 480
1152 x 864
1280 x 1024
WXGA
1280 x 768
UXGA
1360 x 768
1366 x 768
1600 x 1200
◆
◆
◆
◆
Vertical
frequency (Hz)
Horizontal
frequency (kHz)
70
85
85
70
85
60
72
75
85
56
60
72
75
85
60
70
75
85
60
72
75
85
60
75
60
75
60
75
60
60
60
31.5
37.9
37.9
31.5
37.9
31.5
37.9
37.5
43.3
35.2
37.9
48.1
46.9
53.7
48.4
56.5
60.0
68.7
29.8
35.1
36.0
37.0
31.8
67.5
64.0
80.0
47.7
60.1
47.8
48.2
75.0
PPM42S3
✔
✔
✔
✔
✔
✔/
✔
✔
✔
✔
✔/
✔
✔
✔
✔/
✔
✔
✔
✔/
✔
✔
✔
✔/
✔/❉
✔/❉
✔/❉
PPM50H3
PPM63H3
✔
✔
✔
✔
✔
✔/
✔
✔
✔
✔
✔/
✔
✔
✔
✔
✔
✔/
✔
✔/
✔
✔
✔
✔
✔
✔
✔
✔
✔/
✔
✔
✔
✔
✔/
✔
✔
✔
✔
✔
✔/
✔
✔/
✔
✔
✔
✔
✔/
✔
✔
✔/
✔/
✔/
✔
✔
✔/
✔
✔
✔/
✔/
✔/
✔
“❉” mode does not work with DVI mode.
The interlace mode is not supported.
The PDP might operate abnormally if a non-standard video format is selected.
The 1366 x 768/ 852 x 480 mode is only supported by a particular video card (PIXEL PERFECT made by
IMAGINE GRAPHICS Ltd.).
◆ A “✔” mark means that this mode can be supported.
◆ A “ ” mark means that this mode is recommended.
46
D61A-BN68-00492A-00_ENG
2003.11.18
9:32 AM
Page 47
Power Saver (PC1 mode only)
ENG
This monitor has a built-in power management system called Power Saver. This power management
system saves energy by switching your monitor into a low-power mode when it has not been used for a
certain amount of time. This power management system operates with a VESA DPMS compliant video
card installed in your computer. You use a software utility installed on your computer to set up this
feature. See the table below for details.
Normal
Operation
State
Power-saving Function Mode
Horizontal Sync
Active
Inactive
Suspend Mode
Position A1
Active
Vertical Sync
Active
Active
Inactive
Inactive
Video
Active
Blanked
Blanked
Blanked
Power Indicator
Off
Red Blinking
Red Blinking
Red Blinking
(1 sec Interval)
(1 sec Interval)
(1 sec Interval)
Standby Mode
Power-off Mode
Position A2
Inactive
◆ This monitor automatically returns to normal operation when horizontal and vertical sync return.
◆ This occurs when moving the computer’s mouse or pressing a key on the keyboard.
◆ For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long
periods.
47
D61A-BN68-00492A-00_ENG
2003.11.18
9:32 AM
Page 48
Troubleshooting: Before Contacting Service Personnel
ENG
Before contacting Samsung after-sales service, perform the following simple checks.
If you cannot solve the problem using the instructions below, note the model and serial number of the
PDP and contact your local dealer.
No sound or picture
◆
◆
◆
◆
Normal picture but no sound
◆ Check the volume.
◆ Check whether the volume MUTE button on the remote control has
been pressed.
No picture or black and white picture
◆ Adjust the color settings.
◆ Check that the video system selected is correct.
Sound and picture interference
◆ Plug your PDP into a different mains socket.
Remote control malfunctions
◆ Replace the remote control batteries.
◆ Clean the upper edge of the remote control (transmission window).
◆ Check the battery terminals.
Check that the mains lead has been connected to a wall socket.
Check that you have pressed the ON or OFF button.
Check the picture contrast and brightness settings.
Check the volume.
Care and Maintenance
◆ Identifying Problems
- Do not put the PDP near extremely hot, cold, humid or dusty places.
- Do not put the PDP near appliances that create magnetic fields.
- Keep the ventilation openings clear.
- Do not place the PDP on a rough and slanted surface, such as cloth or paper.
◆ Liquids
Do not place liquids near or on the PDP.
◆ Cabinet
- Never open the cabinet or touch the parts inside.
- Wipe your PDP with a clean, dry cloth. Never use water, cleaning fluids, wax, or chemicals.
- Do not put heavy objects on top of the cabinet.
◆ Temperature
If your PDP is suddenly moved from a cold to a warm place, unplug the power cord for at least two
hours so that moisture that may have formed inside the unit can dry completely.
48
D61A-BN68-00492A-00_ENG
2003.11.18
9:32 AM
Page 49
Technical Specifications
ENG
Exterior design and product specifications are subject to change without prior notice to improve the
performance of this product.
This PDP applies to Class B digital device for home use.
This PDP has been registered for residential use in terms of EMI. So it can be used in all areas as well as
residential areas.
Dimensions
(W x D x H)
PPM42S3 - 1027 x 79 x 630.5 mm ; 40.43 x 3.11 x 24.82 inches
PPM50H3 - 1204.6 x 79 x 724 mm ; 47.43 x 3.11 x 28.5 inches
PPM63H3 - 1503.4 x 89 x 893.8 mm ; 59.19 x 3.5 x 35.19 inches
Weight
(Without stand)
PPM42S3 - 31kg
PPM50H3 - 43kg
PPM63H3 - 69kg
Screen aspect ratio
16:9
Screen size
PPM42S3 - 42 inch
PPM50H3 - 50 inch
PPM63H3 - 63 inch
Native pixel resolution
(H x V)
PPM42S3 - 852 x 480
PPM50H3/PPM63H3 - 1366 x 768
Color systems
PAL, SECAM, NTSC (NT3.58/NT4.43)
Sound
Stereo, Virtual Dolby
Audio output power
10W + 10W (8Ω)
Power supply
U.S.A/Canada - AC120V~, 60Hz
Other countries - AC100-250V~, 50/60Hz
Power consumption
PPM42S3 - 380 Watts
PPM50H3 - 480 Watts
PPM63H3 - 630 Watts
Video inputs
VIDEO IN - VIDEO/S-VIDEO
COMPONENT1 IN - Y/Pb/Pr (RCA, 3P, 480i~1080i)
COMPONENT2/RGB2(PC2) IN
(BNC, 480i~1080i (Pr/Y/Pb), VGA~XGA (R/G/B/H/V))
RGB1(PC1) IN - D-SUB, 15P
DVI IN - DVI-D type
Monitor outputs
VIDEO OUT - VIDEO/L/R (RCA, 3P)
Audio inputs
VIDEO IN - L/R
COMPONENT1 IN - L/R (RCA, 2P)
AUDIO (Stereo jack for COMPONENT2,RGB1/2(PC1/2), and
DVI input)
Audio outputs
EXT SPEAKER (8Ω) - R-/+, L-/+
External control
RS232C - IN (Stereo jack), OUT (D-SUB, 9P)
49
D61A-BN68-00492A-00_ENG
2003.11.18
Memo
ENG
50
9:32 AM
Page 50
D61A-BN68-00492A-00_ENG
2003.11.18
9:32 AM
Page 51
Memo
ENG
51
D61A-BN68-00492A-00_ENG
2003.11.18
9:32 AM
Page 52
- AFTER SALES SERVICE
- Do not hesitate to contact your retailer or service agent
if a change in the performance of your product indicates
that a faulty condition may be present.
ELECTRONICS
BN68-00492A-00
Download PDF