Samsung | HT-AS725 | Samsung HT-AS725T User Manual

Digital Surround
AV Receiver System
AV-R725
HT-AS725
THIS APPLIANCE IS MANUFACTURED BY:
Instruction Manual
AH68-02103C
AV-R720-ENG-비유럽향.indb 2-3
2007-12-10 오후 5:22:53
Safety Warnings
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE REAR COVER (or BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This symbol indicates “dangerous voltage” inside
the product that presents a risk of electric shock or
personal injury.
This symbol indicates important instructions
accompanying the product.
CLASS 1 LASER PRODUCT
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
PRODUCTO LASER CLASE 1
Precautions
PREPARATION
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
ENG
This Compact Disc player is classified as a CLASS 1 LASER
product.
Use of controls, adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
Ensure that the AC power supply in your house complies with the identification sticker located on the back of your player. Install
your player horizontally, on a suitable base (furniture), with enough space around it for ventilation (7.5~10cm). Make sure the
ventilation slots are not covered. Do not stack anything on top of the player. Do not place the player on amplifiers or other
equipment which may become hot.
Before moving the player, ensure the Disc Insert Hole is empty. This player is designed for continuous use. Switching off the
DVD player to the stand-by mode does not disconnect the electrical supply. In order to disconnect the player completely from
the power supply, remove the main plug from the wall outlet, especially when left unused for a long period of time.
CAUTION : INVISIBLE LASER RADIATION WHEN OPEN AND
INTERLOCKS DEFEATED, AVOID EXPOSURE
TO BEAM.
WARNING
To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
CAUTION
APPARATUS SHALL NOT BE EXPOSED TO DRIPPING OR SPLASHING AND NO OBJECTS FILLED WITH LIQUIDS,
SUCH AS VASES, SHALL BE PLACED ON THE APPARATUS.
During thunderstorms, disconnect the AC main plug
from the wall outlet.
Voltage peaks due to lightning could damage the unit.
The Mains plug is used as a disconnect device and
shall stay readily operable at any time.
Do not expose the unit to direct sunlight or other heat
sources.
This could lead to overheating and malfunction of the
unit.
Protect the player from moisture (i.e. vases) , and excess
heat (e.g.fireplace) or equipment creating strong magnetic
or electric fields (i.e.speakers...). Disconnect the power
cable from the AC supply if the player malfunctions.Your
player is not intended for industrial use.
Use of this product is for personal use only.
Condensation may occur if your player or disc has been
stored in cold temperatures.
If transporting the player during the winter, wait
approximately 2 hours until the unit has reached room
temperature before using.
The batteries used with this product contain
chemicals that are harmful to the environment.
Do not dispose of batteries in the general household
trash.
(Saudi Arabian Standards Organisation only)
THIS APPLIANCE IS FITTED WITH 220V SASO APPROVED PLUG.THE CUSTOMER IS ENTITLED TO A
FREE SASO APPROVED 127V PLUG FROM THE LOCAL DEALER.
2
AV-R720-ENG-비유럽향.indb 2-3
3
2007-12-10 오후 5:22:59
Features
This product is a pure digital AV receiver that performs digital signal processing to minimise
signal distortion and loss.
Contents
PREPARATION
Dolby Pro Logic llx
Safety Warnings ..............................................................................................................2
Precautions......................................................................................................................3
Features ..........................................................................................................................4
Description.......................................................................................................................6
Dolby Pro Logic IIx is a new technology that provides discrete 7.1 channel out of 2 channel
or multi channel sources.It also provides Music,Movie and Game modes.
CONNECTIONS
DTS 96/24
DTS is a surround format that implements 5.1 channel multi channel sound at 96KHz/24bit.
In addition, it can also reproduce the matrix 6.1 of DTS 96/24 decorder signals.
DOLBY DIGITAL EX
Adds a surround back channel for more spacious sound compared to regular 5.1 channel
Dolby Digital.
DTS (Digital Theater Systems)
DTS plays back 5.1 channel sound with less compression than Dolby Digital for richer sound.
DTS-ES (Extended Surround)
DTS-ES adds an additional rear center surround channel for 6.1 channel sound.
It is compatible with existing DTS Digital Sound formats.
DTS
Reproduces digital PCM or analogue stereo over 6.1 channel using a high precision DTS
digital matrix.
SFE (Sound Field Effect) Using 24bit Audio Digital Signal Processing
PREPARATION
Digital AV Receiver
ENG
Connecting the speakers .................................................................................................10
Connecting external devices ...........................................................................................12
Anynet+ ...........................................................................................................................16
Connecting the FM antennas ..........................................................................................17
OPERATION
Before using the AV receiver ...........................................................................................18
Selecting digital/analogue input .......................................................................................19
Setting the speaker mode................................................................................................20
Setting the speaker listening distance .............................................................................22
Setting digital input ..........................................................................................................23
Setting HDMI AUDIO .......................................................................................................24
Setting DRC (Dynamic Range Compression) .................................................................25
Test tone..........................................................................................................................26
Setting speaker level .......................................................................................................28
Dolby Pro Logic llx mode .................................................................................................29
Setting Dolby Pro Logic llx effect .....................................................................................30
Setting NEO:6 mode........................................................................................................31
Setting EX/ES mode ........................................................................................................32
Setting Tone Control........................................................................................................33
SFE mode........................................................................................................................34
Stereo mode ....................................................................................................................35
RADIO OPERATION
Provides more realistic surround sound with normal stereo audio sources.
Listening to radio .............................................................................................................36
Presetting radio stations ..................................................................................................37
Anynet+ (HDMI-CEC) Function
MISCELLANEOUS
Anynet+ is a function that can be used to operate this AV Receiver with a Samsung TV
remote control, by connecting the receiver to a SAMSUNG TV using an HDMI Cable.
(This function is available only in connection with Samsung TV and DVD player supporting
Anynet +(HDMI-CEC).)
4
AV-R720-ENG-비유럽향.indb 4-5
Convenient functions .......................................................................................................38
Operating your TV with the remote control ......................................................................41
Operating your DVD (VCR) with the remote control ........................................................43
Before calling for service .................................................................................................45
Specifications ..................................................................................................................47
5
2007-12-10 오후 5:23:02
ENG
Description
[ Rear panel ]
TONE CONTROL button
POWER STANDBY INDICATOR
POWER button
AUX IN JACK
HEADPHONE JACK
Remote control sensor SURROUND button
CD AUDIO INPUT JACKS HDMI OUTPUT JACK
VCR AUDIO
VCR VIDEO INPUT JACK
FM ANTENNA JACK
INPUT JACKS
VCR VIDEO OUTPUT JACK
HDMI INPUT
7.1 CH ANALOG
JACKS
FRONT SPEAKER TERMINALS
AUDIO INPUT JACKS
SURROUND SPEAKER TERMINALS
7.1CH IN STEREO button
VOLUME CONTROL
FUNCTION button
INPUT MODE button
SETUP button
TUNING MODE button
SELECT (.,,) button
CENTER SPEAKER TERMINALS SURROUND BACK SPEAKER
TERMINALS
MONITOR VIDEO OUTPUT JACK
DVD VIDEO INPUT JACK
SAT(CABLE/SATELLITE/SET-TOP BOX) VIDEO INPUT JACK
SUBWOOFER AUDIO OUTPUT JACK
DVD OPTICAL DIGITAL
AUDIO INPUT JACK
[ Display ]
SAT (ANYNET+)
OPTICAL AUDIO INPUT JACK
DOLBY DIGITAL EX INDICATOR
SPEAKER INDICATORS
PREPARATION
[ Front panel ]
CD COAXIAL DIGITAL
AUDIO INPUT JACK
DVD AUDIO INPUT JACKS
DIGITAL LIVE SURROUND
INDICATOR INDICATOR
VCR AUDIO OUTPUT JACKS
SAT AUDIO INPUT JACKS
L.PCM INDICATOR
RADIO BROADCASTING
RECEIVING INDICATOR
 Accessories 
RADIO FREQUENCY
INDICATOR
FRONT DISPLAY
RADIO STEREO INDICATORS
Remote control
FM antenna
User’s manual
DTS INDICATOR
6
AV-R720-ENG-비유럽향.indb 6-7
7
2007-12-10 오후 5:23:06
ENG
Description (Cont'd)
PREPARATION
[ Remote control ]
Insert remote control batteries
TV button
AMP button
DVD button
VCR button
1
DIMMER button
POWER button
NUMBER (0~9) buttons
SLEEP button
SUBWOOFER button
EX/ES button
TV/VIDEO, FUNCTION button
CD button
VCR button
DVD button
Remove the battery
cover in the direction
of the arrow.
2
Insert two 1.5V AAA
batteries, paying
attention to the correct
polarities (+ and –).
3
Replace the battery
cover.
7.1 CH button
SAT button
AUX button
INPUT MODE button
MO/ST button
TUNER button
EXTERNAL DEVICE PLAYBACK button
MUTE button
VOLUME CONTROL button
SETUP/MENU button
TUNING/CHANNEL button
TUNING MODE button
NEO : 6 MODE button
STEREO button
Range of operation of the remote control
The remote control can be used up to approximately 23 feet/7 meters in a straight line. It can also be operated
at a horizontal angle of up to 30° from the remote control sensor.
CURSOR/ENTER button
DRC button
INFO button
Follow these precautions to avoid leaking or cracking batteries:
• Place batteries in the remote control so they match the polarity:(+) to (+)and (–)to (–).
• Use the correct type of batteries. Batteries that look similar may differ in voltage.
• Always replace both batteries at the same time.
• Do not expose batteries to heat or flame.
TUNER MEMORY button
MODE button
EFFECT button
TEST TONE button
SPK LEVEL button
SFE MODE button
8
AV-R720-ENG-비유럽향.indb 8-9
SPK SELECT button
9
2007-12-10 오후 5:23:10
ENG
Connecting the speakers
Before moving or installing the product, be sure to turn off the power and disconnect the power cord.
ACTIVE SUBWOOFER
(BUILT-IN POWER AMPLIFIER)
PS-AW725
FRONT (R)
PS-AF725
SYSTEM MODEL NAME : HT-AS725
Position of AV Receiver
Surround Speakers
• Place AV Receiver on a dedicated stand or rack.
• Place these speakers behind your listening position.
• If there isn't enough room, place these speakers so they
face each other.
• Place them about 60 to 90cm (2 to 3feet) above your
ears, facing slightly downward.
Unlike the front and center speakers, the surround
speakers are used to handle mainly sound effects and
sound will not come from them all the time.
• Place these speakers in front of your listening
position, facing inwards (about 45°) toward you.
• Place the speakers so that their tweeters will be at
the same height as your ears.
• Align the front face of the front speakers with the front
face of the center speaker or place them slightly in
front of the center speaker.
Center speaker
• It is best to install it at the same height as the front
speakers.
• You can also install it directly over or under the TV.
Surround Back Speakers SBL SBR
• If you are using two rear center speakers, place them
facing forward from behind the listening position.
• Place the surround back speaker about 70 cm to 1 m
(2.3~3.3feet) above surround speakers, facing slightly
downwards.
Subwoofer
• The position of the subwoofer is not so critical.
Place it anywhere you like.
Subwoofer function
Active subwoofer with integrated 150W amplifier provides rich bass sound.
3
Connect the SW OUT terminal of the amplifier (AV-R725) to the INPUT
terminal of the subwoofer speaker.
Press the POWER button on the rear side of the subwoofer to turn
the power on.
Using the subwoofer’s VOLUME control, you can set the desired bass level
(See page 28 "Setting Speaker Level" to set the subwoofer level in the menu).
10
AV-R720-ENG-비유럽향.indb 10-11
SURROUND
BACK (L)
PS-AB725
MAIN UNIT
AV-R725
SBR
Front Speakers
2
SURROUND
BACK (R)
PS-AB725
SR
SBL
1
SURROUND (L)
PS-AR725
CONNECTIONS
SL
FRONT (L) SURROUND (R)
PS-AF725
PS-AR725
CENTER
PS-AC725
MAIN UNIT
FRONT SPEAKER
CENTER SPEAKER
SURROUND SPEAKER
SURROUND BACK SPEAKER
ACTIVE SUBWOOFER
AV-R725
PS-AF725
PS-AC725
PS-AR725
PS-AB725
PS-AW725
► CONNECTING SPEAKER WIRE
1. Loosen the knob by turning counterclockwise.
2. Insert the bare part of the wire into the hole in the side of each terminal.
3. Tighten the knob by turning clockwise to secure the wire.
• When you attach the speakers to a wall, make sure
to fasten them tightly so they do not fall off.
► Connecting the Speakers
1. Press down the terminal tab on the back of the speaker.
2. Insert the black wire into the black terminal (–) and the red wire
into the red (+) terminal, and then release the tab.
3. Connect the connecting plugs to the back of the AV receiver.
• Make sure the colors of the speaker terminals match the colors
of the connecting plugs.
Caution
• Keep the subwoofer speaker out of reach of children to
prevent them from inserting their hands or objects into the
duct (hole).
1
2
Black
Red
• Never touch speaker terminals while the power is on.
Doing so could result in electric shock.
• Make sure the polarities (+ and -) are correct.
• This system is capable of reproducing 6.1/7.1 channel
sound, however only 5.1 speakers are supplied.
11
2007-12-10 오후 5:23:14
ENG
Connecting external devices
Connecting video devices
Before moving or installing the product, be sure to turn off the power and disconnect the power cord.
SAT(Cable/Satellite/Settop Box)
DVD or Blu-RAY Player
CONNECTIONS
• If the external component has only one audio output
jack, connect it to either the right or left audio input
jack of the main unit.
• Connect the audio cable's red plug to the red jack
and white cable to the white jack.
ali
or
TV
• Disconnect the power plug from the outlet if you will not use this unit for a long period of time.
• Even though the Digital Audio inputs are labelled DVD, SAT and CD, you can connect your DVD/SAT/CD player to
either the OPTICAL or COAXIAL digital audio input (as long as it matches the Digital audio output on your player).
TV
VCR
12
AV-R720-ENG-비유럽향.indb 12-13
13
2007-12-10 오후 5:23:24
ENG
Connecting external devices
(cont’d)
Connecting audio/7.1 channel devices
Connecting external devices via HDMI
Before moving or installing the product, be sure to turn off the power and disconnect the power cord.
By connecting through the HDMI(High-Definition Multimedia Interface) interface, you can play back digital video and audio
without conversion to analog.
DVD or Blu-RAY Player
CD Player
SAT(Cable/Satellite/Set-top box)
CONNECTIONS
• Connect it if
you want to use
Anynet+.
• Audio from SACD discs will not be played. To play
a DVD disk whose copyright is protected by CPPM,
use a player supporting CPPM.
• The quality of the audio output through the HDMI
jack (sampling frequency and bit rate) may be
limited by the performance of the connected device.
• Since HDMI connection supports both video and
audio, you don’t have to connect an additional audio
cable.
TV
High-bandwidth Digital Content Protection System (HDCP) support
To play digital contents through the HDMI connection, both of the connected external device and TV must support High-bandwidth Digital Content
Protection System (HDCP). This product supports HDCP.
TV
DVD/Blu-RAY or 7.1 channel player
COMPATIBILITY WITH A TV SUPPORTING HDMI
A TV with an HDMI jack.
Video/Audio
A TV with a DVI-D jack (TV supporting HDCP)
Video
A TV with a DVI-D jack (TV not supporting HDCP)
-
• If you use an HDMI cable to connect a Samsung TV to the DVD Player, you can operate the AV receiver using the TV’s remote
control. This function is available only in connection with Samsung TV and DVD player supporting Anynet +(HDMI-CEC).
• Please check the n logo. If your TV has an n logo, then it supports the Anynet+ function.
14
AV-R720-ENG-비유럽향.indb 14-15
15
2007-12-10 오후 5:23:26
Anynet+
Connecting external devices
ENG
(Cont'd)
Using Anynet+(HDMI-CEC)
Connecting AUX components
1 Connect the AV receiver to a Samsung TV with an HDMI cable. (See page 15)
the Anynet+ function on your TV. (See the TV instruction manual for more information.)
2 Set
•
You can connect external devices you use (camcorder, game console, mobile equipment,etc.) to the front of this unit for
convenience.
You can operate the AV receiver by using the TV remote control.
button.)
(Available TV button : VOLUME ,
CONNECTIONS
If you select TV
Set the Anynet+(HDMI-CEC) function to <On> on your TV.
• Receiver : On : You can listen to audio through the AV Receiver.
• Receiver : Off : You can listen to audio through the TV.
MOVE
MOVE
ENTER
ENTER
EXIT
EXIT
If you select the DVD Player
Camcorder
Select THEATER to connector and set the option of each items below.
• View TV : If Anynet+(HDMI-CEC) set to on and you select View TV, the AV receiver will
automatically switch to SAT OPTIC2(DIGITAL IN).
MOVE
ENTER
EXIT
• Receiver : On : You can listen to audio through the AV receiver.
• Receiver : Off : You can listen to audio through the TV.
To turn off Anynet+
1 Press SETUP/MENU button, and then press the ENTER button.
• “SETUP MODE” appears on the display and goes into Setup Mode.
2 Press ◄ ► button to select the “ANYNET+ MODE”, and then press the ENTER
button.
3 Press the ▲▼ button to set ANYNET+ to OFF..
- If you are using Anynet+, set ANYNET+ to ON and if not, set it to OFF.
Connecting the FM antenna
To exit setup mode
• Wait for about 5 seconds or press SETUP button.
“SETUP OFF” appears on the display and Setup Mode is exited.
• When selecting View TV, you must have a digital optical cable connected
from the TV to the AV receiver to listen to the TV sound through the AV
receiver.
Caution
• When you are making Anynet+ connection, do not connect more than two AV receivers
(Anynet+ installed). Otherwise, it can cause a malfunction.
With Anynet+
You can operate this unit, power on your TV, or watch a movie by pressing the Play button on
your Samsung TV's remote control.
16
AV-R720-ENG-비유럽향.indb 16-17
FM antenna (supplied)
FM antenna connection
1. Connect the FM antenna supplied to the FM 75Ω COAXIAL terminal as a temporary measure.
2. Slowly move the antenna wire around until you find a location where reception is good, then fasten it to a
wall or other rigid surface.
17
2007-12-10 오후 5:23:29
Before using the AV receiver
Selecting digital/analogue Input
ENG
You can listen to sound in 2 channel analog , Dolby Digital or DTS using this unit.
Turning On/Off
Connect the power plug to the outlet.
Press the POWER button of the remote control.
• This unit will be turned on or set to Standby mode.
Remote control functions
You can operate your AMP (this AV receiver), TV, DVD and VCR with this
remote control.
See pages 41-44 for more details.
Method 1
Press the FUNCTION button.
• Each time you press this button, FM ˆ 7. 1 MULTI CH ˆ CD ˆ DVD
MAIN UNIT
Press the INPUT MODE button.
Press the INPUT MODE button.
• Each time you press this button, input mode changes
• Each time the button is pressed, input mode changes
as follows:
OPERATION
To select a function
REMOTE CONTROL
as follows:
For DVD/SAT function
ˆ SAT ˆ VCR ˆ AUX will be selected in turn.
Method 2
Press CD, VCR, DVD, 7.1CH, SAT, AUX or TUNER button.
►
►
►
►
or
• You can directly select the desired function.
For CD function
►
• You can change the digital input setting for DVD, SAT and CD functions in the “DIGITAL IN” setup.
(See page 23)
• You can enjoy Dolby Digital or DTS if you connect the digital audio output jack of an external audio
component to the optical or coaxial digital audio input jack on the main unit.
18
AV-R720-ENG-비유럽향.indb 18-19
19
2007-12-10 오후 5:23:35
ENG
Setting the speaker mode
Signal outputs and frequency response from the speaker will be adjusted according to your speaker configuration
and whether certain speakers are used or not.
►
REMOTE CONTROL
SETUP/MENU button, and then press ENTER button.
1 Press
“SETUP MODE” appears on the display and goes into Setup Mode.
•
◄ ► button to select the “SPK SETUP”, and then
2 Press
press ENTER button.
MAIN UNIT
SETUP button, and then press ENTER ( ) button.
1 Press
“SETUP MODE” appears on the display and goes into Setup Mode.
◄ ► button to select the speaker you want.
3 Press
Each time you press this button, FRONT ˆ CEN ˆ SURR ˆ S.BACK ˆ
•
•
▲▼ button to set the mode (LARGE, SMALL etc.)
4 Press
for the selected speaker.
press ENTER (
OPERATION
2 Press ◄ ► button to select the “SPK SETUP”, and then
SUB ˆ CROVR will be selected in turn.
) button.
◄ ► button to select the speaker you want.
3 Press
Each time you press this button, FRONT ˆ CEN ˆ SURR ˆ S.BACK ˆ
5 Repeat steps 3-4 to set the mode for each speaker.
•
SUB ˆ CROVR will be selected in turn.
To exit setup mode
4 Press ▲▼ button to set the mode (LARGE, SMALL etc.)
• Wait for about 5 seconds or press SETUP/MENU button.
“SETUP OFF” appears on the display and Setup Mode is exited.
for the selected speaker.
5 Repeat steps 3-4 to set the mode for each speaker.
Using the SPK SELECT button
1 Press SPK SELECT button to select the speaker you want.
• Each time you press this button, FRONT ˆ CEN ˆ SURR ˆ S.BACK ˆ SUB
To exit setup mode
ˆ CROVR will be selected in turn.
• Wait for about 5 seconds or press SETUP button.
2 Press ▲▼ button to set the mode (LARGE, SMALL etc.) for
the selected speaker.
3 Repeat steps 1-2 to set the mode for each speaker.
To turn the SUBWOOFER on or off.
Press SUBWOOFER button on the remote.
• Each time you press this button, SUB : YES, SUB : NO will be selected in turn.
• If FRONT is set to LARGE, you can select YES or NO for SUB.
• If FRONT is set to SMALL, SUB is automatically set to YES.
NO cannot be selected.
20
AV-R720-ENG-비유럽향.indb 20-21
“SETUP OFF” appears on the display and Setup Mode is exited.
Setting the Speaker
SPEAKER
Possible Settings
FRONT(Front)
LARGE, SMALL
CEN(Centre)
LARGE, SMALL, NONE
SURR(Surround)
LARGE, SMALL, NONE
S.BACK (Surround Back) LARGE, SMALL, NONE
SUB(Subwoofer)
YES,NO
CROVR
60,80,100,120,
(Crossover Frequency)
150,180,200(Hz)
Default Setting
SMALL
SMALL
SMALL
SMALL
YES
150Hz
• LARGE : Select when using large speakers. You can listen to full range
sound.
• SMALL : Select this when using small speakers
• NONE : Select when no speaker is used
• YES (subwoofer) : Select when using the subwoofer speaker.
• NO (subwoofer) : Select when not using the subwoofer speaker.
• CROVR : Select the crossover frequency for the best bass response
in your room.
21
2007-12-10 오후 5:23:39
Setting the speaker listening distance
Setting digital input
If the speakers cannot be placed at equal distances from the listening position, you can adjust the
delay time of the audio signals from the centre and surround speakers.
You can set the digital input for a DVD/SAT/CD player to either OPTICAL or COAXIAL to match the
connections you've made.
ENG
►
►
1 Press SETUP/MENU button, and then press ENTER
1 Press SETUP/MENU button, and then press ENTER
button.
• “SETUP MODE” appears on the display and goes into Setup Mode.
2 Press ◄ ► button to select the “DIST SETUP”, and then
press ENTER button.
button.
• “SETUP MODE” appears on the display and goes into Setup Mode.
2 Press ◄ ► button to select the “DIGITAL IN”, and then
press ENTER button.
◄ ► button to select the speaker you want.
3 Press
Each time you press this button, F.L ˆ CEN ˆ F.R ˆ S.R ˆ SBR ˆ SBL ˆ
•
S.L ˆ S.W will be selected in turn.
• For F.L, CEN, F.R, S.W, S.R, SBR, SBL, S.L Speaker, you can set the
distance from the speaker to listening position between 0.3~9.0m in intervals
of 0.3m.
function.
• Each time you press this button, CD ˆ DVD ˆ SAT will be selected in turn.
OPERATION
4 Press ▲▼ button to set the speaker distance.
3 Press ◄ ► button to select the the CD, DVD or SAT
4 Press ▲▼ button to set the digital input.
• Each time you press this button, COAXIAL ˆ OPTICAL2 ˆ OPTICAL1 will
be selected in turn..
To exit setup mode
• Wait for about 5 seconds or press SETUP/MENU button.
“SETUP OFF” appears on the display and Setup Mode is exited.
To exit setup mode
• Wait for about 5 seconds or press SETUP/MENU button.
“SETUP OFF” appears on the display and Setup Mode is exited.
Setting Speaker Distance
Set the distance from the speaker to listening position in intervals of 0.3m.
• F.L (front left) : 0.3m ~ 9m
• F.R (front right) : 0.3m ~ 9m
• SBR (surround back right) : 0.3m ~ 9m
• S.L (surround left) : 0.3m ~ 9m
• CEN (centre) : 0.3m ~ 9m
• S.R (surround right) : 0.3m ~ 9m
• SBL (surround back left) : 0.3m ~ 9m
• SW (subwoofer) : 0.3m ~ 9m
• If the listening position is beyond the range of the speaker distance
setup, set the speaker distance to the maximum.
• The distance range of the overall speaker system is determined based
on the F.L(front left) speaker distance from the listening position.
• Based on the max delay channel, the distance of the front speaker is
1.5m(5ms) and the surround speaker can be set up to 4.5m(15ms).
22
AV-R720-ENG-비유럽향.indb 22-23
• You can select only one digital input for each function. Example)
If you have selected COAXIAL for the CD function, you cannot
select COAXIAL for the DVD or SAT function.
Function
DVD
SAT
CD
Digital input
OPTICAL1
OPTICAL2
COAXIAL
23
2007-12-10 오후 5:23:41
DRC (Dynamic Range Compression)
Setting HDMI AUDIO
Setting
You can set HDMI audio settings.
You can use this function to enjoy Dolby Digital sound when watching movies at low volume at night.
DRC compresses the audio to make the loudest sounds quieter and the quietest sounds louder.
►
Before using!
• Press the INPUT MODE button to select HDMI1 or HDMI2. (see page 19)
• If you select Digital (Optical, Coaxial) or Analogue, the HDMI audio
setting will be deactivated.
1 Press SETUP/MENU button, and then press ENTER
button.
• “SETUP MODE” appears on the display and goes into Setup Mode.
2 Press ◄ ► button to select the “HDMI AUDIO”, and then
• “HDMI : AVR” appears on the display.
▲▼ button to set the HDMI audio.
3 Press
Each time you press this button, HDMI : AVR ˆ HDMI : TV will be selected
•
in turn.
►
1 Press SETUP/MENU button, and then press ENTER
button.
• “SETUP MODE” appears on the display and goes into Setup Mode.
2 Pritisnite gumb ◄ ► in izberite "DRC SETUP", nato pa
pritisnite gumb ENTER.
• Na zaslonu se prikaže "DRC : STD" (Standardno stiskanje).
3 S pritiskom na gumb ▲▼ nastavite DRC.
• S pritiskom na ta gumb izbirate med možnostmi DRC : STD ˆ DRC : MAX
OPERATION
press ENTER button.
ENG
ˆ DRC : MIN.
To exit setup mode
• Wait for about 5 seconds or press SETUP/MENU button.
“SETUP OFF” appears on the display and Setup Mode is exited.
To exit setup mode
• Wait for about 5 seconds or press SETUP/MENU button.
“SETUP OFF” appears on the display and Setup Mode is exited.
Using the DRC button
Press DRC button.
• Each time you press this button, DRC : STD ˆ DRC : MAX ˆ DRC : MIN will
be selected in turn.
Setting HDMI AUDIO
• AVR : Audio is played on this product.
• TV : Audio is played on a TV connected to the HDMI OUT jack and no audio is
played on this product.
Setting DRC
• STD : Sets DRC effect to standard.
• MAX : Sets DRC effect to maximum.
• MIN : Sets DRC effect to minimum.
• This function is available when both video input and outputs HDMI.
• HDMI AUDIO setting is available only when the HDMI output is
connected to a TV.
• If you do not hear sound from the TV, should change the HDMI audio
24
AV-R720-ENG-비유럽향.indb 24-25
output setting for your DVD PLAYER or SAT to PCM.
25
2007-12-10 오후 5:23:44
ENG
Test tone
Use the test tone check the speaker connection status or level.
To automatically output test tone
To Manually Output Test Tone
►
1 Press SETUP/MENU button, and then press ENTER
button.
• “SETUP MODE” appears on the display and the unit goes into Setup Mode.
2 Press ◄ ► button to select the “TEST-T AUTO”, and then
press ENTER button.
• Test signal will be automatically output as follows; F.L ˆ CEN ˆ F.R ˆ
output level from -10 to +10 dB by 1 step.
To stop test tone
• Press SETUP/MENU button once time.
1 Press SETUP/MENU button, and then press ENTER
button.
• “SETUP MODE” appears on the display and goes into Setup Mode.
2 Press ◄ ► button to select the “TEST-T MANU”, and
then press ENTER button.
◄ ► button to select the speaker you want.
3 Press
Each time you press ◄ ► button, F.L ˆ CEN ˆ F.R ˆ S.R ˆ SBR ˆ SBL ˆ
OPERATION
S.R ˆ SBR ˆ SBLˆ S.L ˆ S.W .
• During test signal output, press ▲▼ button to adjust the individual speaker
►
•
S.L ˆ S.W will be selected in turn.
4 Press ▲▼ button to set the test tone as you want.
• You can adjust the speaker output level from -10 to +10dB by 1 step.
• The sound gets quieter at -10dB and louder at +10dB.
“SETUP OFF” appears on the display and test tone stops.
Using the Test Tone button
Press TEST TONE button.
To stop test tone
• Press SETUP/MENU button once time.
“SETUP OFF” appears on the display and test tone stops.
• Test signal will be automatically output as follows; F.L ˆ CEN ˆ F.R ˆ S.R ˆ
SBR ˆ SBL ˆ S.L ˆ S.W.
• During test tone output, press ▲▼ button to adjust the speaker output level from
-10 to +10 dB by 1 step.
Test Tone Output
• F.L (front left) : -10 ~ +10dB
• CEN (centre) : -10 ~ +10dB
• F.R (front right) : -10 ~ +10dB
• S.R (surround right) : -10 ~ +10dB
• SBR (surround back right) : -10 ~ +10dB
• SBL (surround back left) : -10 ~ +10dB
• S.L (surround left) : -10 ~ +10dB
• S.W (subwoofer) : -10 ~ +10dB
26
AV-R720-ENG-비유럽향.indb 26-27
27
2007-12-10 오후 5:23:47
Setting speaker level
Dolby Pro Logic llx mode
You can set the balance and level of speakers.
This mode provides 7.1 channel sound from 2 channel sources.
►
ENG
REMOTE CONTROL
Press
MODE button.
• Each time you press this button, CINEMA ˆ MATRIX ˆ GAME ˆ PL ˆ
1 Press SETUP/MENU button, and then press ENTER
MUSIC will be selected in turn.
button.
• “SETUP MODE” appears on the display and goes into Setup Mode.
2 Press ◄ ► button to select the “LEVEL SETUP”, and then
press ENTER button.
3 Press ◄ ► button to select the speaker you want.
• Each time you press ◄ ► button, F.L ˆ CEN ˆ F.R ˆ S.R ˆ SBR ˆ SBL
ˆ S.L ˆ S.W will be selected in turn.
•
• The sound gets quieter at -10dB and louder at +10dB.
To exit setup mode
• Wait for about 5 seconds or press SETUP/MENU button.
“SETUP OFF” appears on the display and Setup Mode is exited.
Using the SPK LEVEL button
1 Press SPK LEVEL button to select the speaker you want.
• Each time you press this button, F.L ˆ CEN ˆ F.R ˆ S.R ˆ SBR ˆ SBL ˆ
S.L ˆ S.W ˆ SPK LVL OFF will be selected in turn.
2 Press ▲▼ button to set the speaker level you want.
• You can adjust it from -10 to +10dB by 1 step.
• The sound gets quieter at -10dB and louder at +10dB.
SURROUND button to select “DPLIIx MODE”.
1 Press
Each time you press this button, DPLIIx ˆ NEO:6 ˆ SFE ˆ STEREO
•
OPERATION
4 Press
▲▼ button to set the speaker mode.
You can adjust it from -10 to +10dB by 1 step.
MAIN UNIT
will be selected in turn.
SELECT (.,,) button.
2 Press
SEach time you press SELECT (,) button, CINEMA ˆ MATRIX ˆ
•
GAME ˆ PL ˆ MUSIC will be selected in turn.
• Each time you press SELECT (.) button, MUSIC ˆ PL ˆ GAME ˆ
MATRIX ˆ CINEMA will be selected in turn.
To exit setup mode
• Wait for about 5 seconds.
Dolby Pro Logic llx mode
• MUSIC : Provides 7.1 channel surround sound for digital, analog or existing stereo
sources such as CD, TAPE, FM, TV and stereo VCR.
• CINEMA : Adds realism to the movie soundtrack.
• MATRIX : You will hear 7.1 channel surround sound.
• GAME : Enhances the excitement of the game's sound.
• PL : You will experience a surround effect with just the front left and right speakers.
Setting Speaker Level
• F.L (front left) : -10 ~ +10dB
• CEN (centre) : -10 ~ +10dB
• F.R (front right) : -10 ~ +10dB
• S.R (surround right) : -10 ~ +10dB
• SBR (surround back right) : -10 ~ +10dB
• SBL (surround back left) : -10 ~ +10dB
• S.L (surround left) : -10 ~ +10dB
• S.W (subwoofer) : -10 ~ +10dB
28
AV-R720-ENG-비유럽향.indb 28-29
• You cannot use Dolby Pro Logic llx mode for multi channel signals such as Dolby Digital
and DTS.
• Pro Logic works only for PCM audio signals with sampling frequencies of 32KHz, 44KHz
or 48KHz.
• Sound will not be output from the surround back speaker if the PCM audio signal is mono.
29
2007-12-10 오후 5:23:49
Setting Dolby Pro Logic llx effect
Setting NEO:6 mode
This function works only in Dolby PRO LOGIC IIx MUSIC Mode.
You can play back 2 channel sound over 6.1 channels when enjoying music or a movie.
1 Press SETUP/MENU button, and then press ENTER
button.
• “SETUP MODE” appears on the display and goes into Setup Mode.
2 Press ◄ ► button to select the “
MODE”, and
then press ENTER button.
◄ ► button.
3 Press
Each time you press this button,
•
C-WIDTH ˆ DIMENSION ˆ
PANORAMA will be selected in turn.
4 Press ▲▼ button to set the
To exit setup mode
• Wait for about 5 seconds or press SETUP/MENU button.
“SETUP OFF” appears on the display and Setup Mode is exited.
Using the
1 Press
2 Press
EFFECT button
MODE button to select ‘MUSIC’ Mode.
EFFECT button.
• Each time you press this button, C-WIDTH l DIMENSION ˆ PANORAMA will
be selected in turn.
3 Press ▲▼ button to select Dolby Pro Logic IIx effect you
want.
• C-WIDTH : You can set from 0 to 7.
• DIMENSION : You can set from -7 to +7.
• PANORAMA : You can set it ON or OFF.
Dolby Pro Logic llx effect
• C-WIDTH : This sets the width of the centre image. The higher the setting, the
less sound comes from the centre speaker.
• DIMENSION : Incrementally adjusts the sound field (DSP)from the front or
surround.
• PANORAMA : This mode extends the front stereo image to include the surround
speakers for an exciting "wraparound" effect with side wall imaging.
30
AV-R720-ENG-비유럽향.indb 30-31
REMOTE CONTROL
Press NEO:6 MODE button.
• Each time you press this button, MUSIC ˆ CINEMA will be selected in turn.
MAIN UNIT
1 Press SURROUND button briefly to select “NEO:6” mode.
• Each time you press this button, DPLIIx ˆ NEO:6 ˆ SFE ˆ STEREO will
be selected in turn.
2 Press SELECT(.,,) button.
• Each time you press this button, MUSIC ˆ CINEMA will be selected in turn.
To set the height of the center sound image
If your TV (or screen) is installed high on a wall, you can raise the center
sound image of the front and center speakers to compensate.
1 Press SETUP/MENU button, and then press ENTER button.
“SETUP MODE” appears on the display and goes into Setup Mode.
2 Press ◄ ► button to select the “NEO:6 MODE”, and then
•
press ENTER button.
OPERATION
Dolby Pro Logic llx effect you
want.
ENG
• “CEN -- IMG : 2” appears on the display.
3 Press ▲▼ button to set the sound image you want.
• You can set the sound image from 0 to 5.
• This parameter adjusts the height of the center image through the front and
center speakers. “0” is the lowest while “5” is the highest.
To exit setup mode
• Wait for about 5 seconds or press SETUP/MENU button.
“SETUP OFF” appears on the display and Setup Mode is exited.
NEO : 6 Mode
This mode decodes 2 channel signals to a high precision digital matrix decoder.
for 6.1 channel sound.
• MUSIC : NEO:6 MUSIC mode is optimized for music playback
• CINEMA : NEO:6 CINEMA mode is optimized for movie playback.
• NEO:6 mode cannot be used with DTS and Dolby Digital multi channel signals.
• Pro Logic works only for PCM audio signals with sampling frequencies of
32KHz, 44KHz or 48KHz.
31
2007-12-10 오후 5:23:53
Setting EX/ES mode
Setting Tone Control
When surround back speakers are connected, you can listen to 6.1 or 7.1 multi-channel sound using the built-in
Dolby Digital Surround EX or DTS ES decoder. This function works when a Dolby Digital or DTS source (such
as a DVD player) is input, and does not work with L.PCM and Dolby Digital 2 channel sources.
This function allows setting up the tone quality of the front speaker.
SETUP/MENU button, and then press ENTER button.
1 Press
“SETUP MODE” appears on the display and goes into Setup Mode.
2 Press ◄ ► button to select the “EX/ES SETUP”, and then
ENG
•
press ENTER button.
• “EX/ES : AUTO” appears on the display.
3 Press ▲▼ button to set the
EX/ES you want.
• Each time you press this button,
EX/ES : AUTO ˆ EX/ES : ON ˆ
EX/ES : OFF will be selected in turn.
1 Press SETUP/MENU button, and then press the ENTER
button.
• “SETUP MODE” appears on the display and goes into Setup Mode.
2 Press ◄ ► button to select the “TONE CONTROL”, and
then press the ENTER button.
◄ ► button.
3 Press
Each time you press this button, BASS ˆ TREBLE ˆ TONE : OFF will be
•
selected in turn.
To exit setup mode
• Wait for about 5 seconds or press SETUP/MENU button.
Using the EX/ES button
▲▼ button to set the tone control you want.
4 Press
You can adjust it from -6 to +6dB by 1 step.
OPERATION
“SETUP OFF” appears on the display and Setup Mode is exited.
• If it is set to TONE: OFF, the Tone Control function will be disabled.
•
• The sound gets smaller at -6dB and louder at +6dB.
Press EX/ES button.
• Each time you press this button, EX/ES : AUTO ˆ EX/ES : ON ˆ EX/ES :
OFF will be selected in turn.
• The EX/ES button on the remote control is enabled only if the input
source is of Dolby Digital or DTS.
To exit setup mode
• Wait for about 5 seconds or press SETUP/MENU button.
“SETUP OFF” appears on the display and Setup Mode is exited.
EX/ES Mode
• AUTO : If the unit receives an audio signal that it can recognize, it will select an
optimal decoder for playback in 6.1/7.1 channel.
If the amplifier does not recognize the audio signal, it will not play in
6.1/7.1 channel automatically.
• ON : Dolby Digital or DTS signal will be played in 6.1 / 7.1 channel using Dolby
Digital Surround EX / DTS ES decoder.
• OFF : Dolby Digital Surround EX / DTS ES decoder will not be used for playback.
Dolby Digital - EX
Movie soundtracks encoded with Dolby Digital EX will play audio over
the surround back channels also.
• You cannot use Dolby Digital-EX in the system without Surround
Back speakers connected.
• EX/ES Mode must be set to On when playing back discs encoded
with 6.1 channel Dolby Digital-EX.
• Some discs encoded with Dolby Digital-EX do not contain an
identification signal. In this case, set EX/ES to ON.
32
AV-R720-ENG-비유럽향.indb 32-33
DTS-ES (Discrete 6.1, Matrix 6.1)
A surround back channel is added to the DTS 5.1 channel
system, improving the sense of sound directionality and space.
A built-in DTS-ES decoder has been equipped with this system
that supports discs encoded with DTS-ES Direct and DTS-ES
Matrix.
• Tone Control function is available only in the Stereo mode.
• You cannot use DTS-ES without surround back
speakers connected.
33
2007-12-10 오후 5:23:57
ENG
SFE mode
Stereo mode
The SFE (Sound Field Effect) function uses 7 different DSP sound field effects to digitally simulate actual music
environments such as concert halls or cinemas.
You can select this mode when listening to sound through the front left and right speakers and subwoofer.
REMOTE CONTROL
REMOTE CONTROL
Press SFE MODE button.
Press STEREO button.
• Each time you press this button, HALL ˆ THEATER ˆ ARENA ˆ CLUB ˆ
• “STEREO” appears in the display and
DOME ˆ STADIUM ˆ CHURCH will be selected in turn.
Stereo Mode is selected.
MAIN UNIT
Press SURROUND button to select ‘STEREO’.
• Each time you press this button, DPLIIx ˆ NEO:6 ˆ SFE ˆ STEREO will
be selected in turn.
• If you press the STEREO button on the player, it will switch to STEREO mode.
To exit setup mode
• Wait for about 5 seconds.
MAIN UNIT
o = active, – = inactive
SURROUND button to select ‘SFE’ Mode.
1 Press
Each time you press this button, DPLIIx ˆ NEO:6 ˆ SFE ˆ
•
STEREO will be selected in turn.
2
Press SELECT(.,,) button.
• Each time you press Select (., ,) button, HALL
CLUB
DOME
OPERATION
Surround Mode and Input Signal Chart
STADIUM
To exit setup mode
• Wait for about 5 seconds.
THEATER ARENA
CHURCH will be selected in turn.
Surround
Mode
DOLBY
(MUSIC,
CINEMA,
MATRIX,
GAME,
PRO LOGIC)
NEO:6
(MUSIC,
CINEMA)
SFE
EX/ES
STEREO
Output Channel
Input Signal
Decoding
Display Information
SL SBL
SR SBR SubW
L/R
C
Dolby D Surr. EX
Dolby Digital 5.1
O
O
O
Dolby D (5.1ch)
Dolby Digital 5.1
O
O
Dolby D (2ch)
Pro Logic II x
O
O
Dolby D (2ch Surr)
Pro Logic II x
O
O
Display Signal Format
Channel Status
O
O
2 DIGITAL
L, C, R, SL, SR, SBL, SBR, SW
O
-
O
2 DIGITAL
L, C, R, SL, SR, SW
O
O
O
2 DIGITAL
L, C, R, SL, SR, SBL, SBR, SW
O
O
O
2 DIGITAL
L, C, R, SL, SR, SBL, SBR, SW
L.PCM (Audio)
Pro Logic II x
O
O
O
O
O
L.PCM
L, C, R, SL, SR, SBL, SBR, SW
Analog
Pro Logic II x
O
O
O
O
O
ANALOGUE
L, C, R, SL, SR, SBL, SBR, SW
L.PCM (Audio)
Neo:6
O
O
O
O
O
L.PCM
L, C, R, SL, SR, SBL, SBR, SW
Analog
Neo:6
O
O
O
O
O
ANALOGUE
L, C, R, SL, SR, SBL, SBR, SW
Dolby D (2ch)
Neo:6
O
O
O
O
O
2 DIGITAL
L, C, R, SL, SR, SBL, SBR, SW
Dolby D (2ch Surr)
Neo:6
O
O
O
O
O
2 DIGITAL
L, C, R, SL, SR, SBL, SBR, SW
Dolby D (2ch)
DD+SFE
O
O
O
-
O
2 DIGITAL
L, C, R, SL, SR, SW
Dolby D (2ch Surr)
DD+SFE
O
O
O
-
O
2 DIGITAL
L, C, R, SL, SR, SW
L.PCM (Audio)
SFE
O
O
O
-
O
L.PCM
L, C, R, SL, SR, SW
Analog
SFE
O
O
O
-
O
ANALOGUE
L, C, R, SL, SR, SW
Dolby D Surr. EX
Dolby Digital EX
O
O
O
O
O
2 DIGITAL
L, C, R, SL, SR, SBL, SBR, SW
Dolby D (5.1-ch)
Dolby Digital EX
O
O
O
O
O
2 DIGITAL
L, C, R, SL, SR, SBL, SBR, SW
L, C, R, SL, SR, SBL, SBR, SW
DTS-ES
DTS-ES
O
O
O
O
O
dts, ES
DTS (5.1ch)
DTS-ES
O
O
O
O
O
dts
L, C, R, SL, SR, SBL, SBR, SW
Dolby D (2ch)
Stereo
O
-
-
-
O
2 DIGITAL
L, R, SW
Dolby D (2ch Surr)
Stereo
O
-
-
-
O
2 DIGITAL
L, R, SW
L.PCM (Audio)
Stereo
O
-
-
-
O
L.PCM
L, R, SW
L.PCM 96KHz
Stereo
O
-
-
-
O
L.PCM
L, R, SW
Analog
Stereo
O
-
-
-
O
ANALOGUE
L, R, SW
L/R : front speaker (left/right) C : centre speaker SL/SR : surround speaker (left/right) SBL/SBR : surround back speaker (left/right)
SW : subwoofer
• Channel status displays are dependent on the speaker configuration.
34
AV-R720-ENG-비유럽향.indb 34-35
• SFE mode works with 2-ch signals.
35
2007-12-10 오후 5:23:59
Listening to radio
Presetting radio Stations
You can listen to the chosen band (FM) by using either automatic or manual tuning.
You can preset up to 30 FM stations.
REMOTE CONTROL
E.g. : Setting station FM 89.10 in preset 2.
1 Press TUNER button.
2 Selected frequency.
1 Press TUNER button.
TUNING MODE button to
2 Press
select MANUAL and then press
• Automatic tuning 1
:
TUNING/CH(.,,) button to
select 89.10.
1) Press TUNING MODE button to select PRESET.
2) Press TUNING/CH (.,,) button to select the preset frequency.
• Automatic tuning 2
• Refer to step 2, page 36, to tune in
:
automatically and manually.
1) Press TUNING MODE button to select MANUAL
2) Press and hold TUNING/CH (.,,) button to automatically tune in frequency.
• Manual tuning :
1) Press TUNING MODE button to select MANUAL.
2) Press TUNING/CH (.,,) button briefly to increase or decrease the
frequency step by step.
TUNER MEMORY button.
3 Press
Tuner number will blink on the display.
•
4 Press TUNING/CH(.,,) button
to select preset 2.
MAIN UNIT
• You can select from presets 1 to 30.
1 Press FUNCTION button to select FM.
the frequency.
2 Select
Automatic tuning 1 :
5 Press TUNER MEMORY button.
• Tuner number will disappear and station 89.10
will be saved in preset 2.
•
RADIO OPERATION
6 To preset other stations, repeat
1) Press TUNING MODE button to select PRESET.
2) Press TUNING/CH (.,,) button to select the preset frequency.
• Automatic tuning 2
ENG
steps 2 to 5.
:
1) Press TUNING MODE button to select MANUAL
2) Press and hold TUNING/CH (.,,) button to automatically tune in frequency.
• Manual tuning :
1) Press TUNING MODE button to select MANUAL.
2) Press TUNING/CH (.,,) button briefly to increase or decrease the frequency
step by step.
To Listen to Preset Station
• Press TUNING MODE button of the remote control to select the PRESET
and press TUNING/CH (.,,) button.
To Listen to mono/stereo
Press MO/ST button on the remote.
• Each time you press this button, STEREO ˆ MONO will be selected in turn.
• If you select MONO in the area with weak reception, it will help to reduce noise.
• This function works only with the Remote Control.
36
AV-R720-ENG-비유럽향.indb 36-37
37
37
2007-12-10 오후 5:24:03
ENG
Convenient functions
Sleep timer function
Reset function
You can set the time that this unit will shut itself off.
Press the SLEEP button.
• SLEEP : OFF ˆ 15 ˆ 30 ˆ 45 ˆ 60 ˆ 90 ˆ 120 M (MIN) will be selected in turn.
REMOTE CONTROL
1 Press the MUTE button.
MUTE appears on the display.
2 Press “0” button five times and then press ENTER
•
To check sleep timer
Press SLEEP button.
• The remaining time before this unit will shut itself off is shown on the display.
• Pressing the button again changes the sleep time from what you set previously.
To cancel sleep timer
button.
• “INITIAL : NO” appears on the display.
▲▼ buttons to select “YES”.
3 Press
The unit will turn off after 5 seconds.
•
• Press SLEEP button until “SLEEP : OFF” appears on the display.
MAIN UNIT
Mute function
This function is useful when answering a doorbell or telephone call.
Press the MUTE button.
• MUTE appears on the display.
To output sound again
1 Turn off the power and hold the SELECT(,) button for
longer than 5 seconds.
• POWER STANDBY indicator will flash.
Caution!
• Using the RESET function will erase all stored settings.
• Do not use this unless necessary.
Press MUTE button again.
• MUTE will disappear and sound will output.
MISCELLANEOUS
• SLEEP, Mute and the Adjust Display function can only be
operated with the remote control.
38
AV-R720-ENG-비유럽향.indb 38-39
39
2007-12-10 오후 5:24:06
Convenient functions
(cont’d)
Adjust the display
You can adjust the brightness of the display.
Press the DIMMER button.
ENG
Operating your TV with the
remote control
1
Press POWER button to turn on
the TV.
2
Press TV button to set the remote to TV
mode.
3
Point the remote control toward the TV.
4
While holding down POWER button,
enter the code corresponding to your
brand of TV.
• Each time you press this, the brightness changes as follows : DARK ˆ BRIGHT.
Using headphones
Use headphones (not supplied) for private listening pleasure.
Connect the headphones to the headphone jack and listen to
music.
• If there is more than one code listed for your TV in the table, enter one
at a time to determine which code works.
• If the code matches the TV's code, the TV will be turned off.
MISCELLANEOUS
5
If TV is turned on or off when you press the
power button of the remote control, the
setting is completed.
• You can use the TV POWER, VOLUME, CHANNEL, MENU and
Numeric buttons (0~9).
• Do not turn the volume up too high when you use headphones as It
may damage your hearing.
40
AV-R720-ENG-비유럽향.indb 40-41
• The remote control may not work on some brands of TVs.
Also, some operations may not be possible depending on your
brand of TV.
• The remote control will work with Samsung TVs by default.
41
2007-12-10 오후 5:24:08
Operating your TV with the remote
control (cont’d)
TV Brand Code List
Brand
Code Number
ADMIRAL (M.WARDS)
A MARK
ANAM
42
AV-R720-ENG-비유럽향.indb 42-43
LUXMAN
LXI (SEARS)
MAGNAVOX
MARANTZ
MATSUI
MGA
MITSUBISHI/MGA
MTC
NEC
NIKEI
ONKING
ONWA
PANASONIC
PENNEY
PHILCO
PHILIPS
PIONEER
PORTLAND
PROTON
QUASAR
RADIO SHACK
RCA/PROSCAN
REALISTIC
SAMPO
SAMSUNG
SANYO
SCOTT
SEARS
SHARP
SIGNATURE 2000 (M.WARDS)
SONY
SOUNDESIGN
SPECTRICON
SSS
Code Number
018
019, 054, 056, 059, 060,
062, 063, 065, 071
015, 017, 018, 048, 054,
059, 060, 062, 072, 089
040, 054
054
018, 040
018, 040, 054, 059, 060,
075, 101
018
018, 019, 020, 040, 059,
060
003
003
003
006, 007, 008, 009, 054,
066, 067, 073, 074
018
003, 015, 017, 018, 048,
054, 059, 062, 069, 090
015, 017, 018, 040, 048
054, 062, 072, 112, 114,
117, 118
063, 066, 080, 091
015, 018, 059
040
006, 066, 067
017, 048, 056, 060, 061,
075
018, 059, 067, 076, 077
078, 092, 093, 094
003, 019
040
000, 015, 016, 017, 040,
043, 046, 047, 048, 049,
054, 059, 060, 098
019, 061, 065, 101, 102,
103, 104
003, 040, 060, 061
015, 018, 019
015, 057, 064, 101, 105,
106, 115
057, 058
050, 051, 052, 053, 055,
101
003, 040
001
018
Brand
SYLVANIA
SYMPHONIC
TATUNG
TECHWOOD
TEKNIKA
TMK
TOSHIBA
VIDTECH
VIDECH
WARDS
YAMAHA
YORK
YUPITERU
ZENITH
ZONDA
DONGYANG
LOWE
FINLUX
YOKO
LOEWE OPTA
PHONOLA
RADIOLA
SCHNEIDER
AKAI
GRUNDIG
BLAUPUNKT
SIEMENS
CGE
IMPERIAL
MIVAR
SABA
BANG&OLUFSEN
BRIONVEGA
FORMENTI
METZ
WEGA
RADIOMARELLI
SINGER
SINUDYNE
TELEFUNKEN
Code Number
018, 040, 048, 054, 059,
060, 062
061, 095, 096
006
018
003, 015, 018, 025
018, 040
019, 057, 063, 071, 101
107, 109, 110, 111, 113
018
059, 060, 069
015, 017, 018, 040, 048,
054, 060, 064
018
040
003
058, 079
001
003, 054
054
054, 109, 114
054
054, 114
054, 112, 114
054, 112
054
103
108, 109, 113, 119, 120,
121
108
108
113
113
113
114
114
114
114
114
114
114
114
114
116
1
2
Press POWER button to turn on the DVD
(VCR).
Press DVD button to set the remote to
DVD mode.
• If you operate VCR, press VCR button to set the remote to VCR
mode.
3
Point the remote control toward the DVD
(VCR).
4
While holding down POWER button, enter
the code corresponding to your brand of
DVD (VCR).
• If there is more than one code listed for your DVD (VCR) in the table,
enter one at a time to determine which code works.
• If the code matches the DVD (VCR)'s code, the DVD (VCR) will be
turned off.
5
If DVD (VCR) is turned on or off when you
press the power button of the remote
controller, the setting is completed.
MISCELLANEOUS
056, 057, 058
001, 015
001, 002, 003, 004,005,
006, 007, 008, 009, 010,
011, 012, 013, 014
AOC
001, 018, 040, 048
BELL & HOWELL (M.WARDS) 057, 058, 081
BROCSONIC
059, 060
CANDLE
018
CETRONIC
003
CITIZEN
003, 018, 025
CINEMA
097
CLASSIC
003
CONCERTO
018
CONTEC
046
CORONADO
015
CRAIG
003, 005, 061, 082, 083,
084
CROSLEX
062
CROWN
003
CURTIS MATHES 059, 061, 063
CXC
003
DAEWOO
002, 003, 004, 015,016,
017, 018, 019, 020, 021,
022, 023, 024, 025, 026,
027, 028, 029, 030, 032,
034, 035, 036, 040, 048,
059, 090, 099, 100
DAYTRON
040
DYNASTY
003
EMERSON
003, 015, 040, 046, 059,
061, 064, 082, 083, 084,
085
FISHER
019, 065, 103
FUNAI
003
FUTURETECH
003
GENERAL ELECTRIC (GE) 006, 040, 056, 059, 066,
067, 068
HALL MARK
040
HITACHI
015, 018, 050, 059, 069
INKEL
045
JC PENNY
056, 059, 067, 086
JVC
070
KTV
059, 061, 087, 088
KEC
003, 015, 040
KMC
015
LG (GOLDSTAR)
001, 015, 016, 017, 037,
038, 039, 040, 041, 042,
043, 044, 054, 086
Brand
Operating your DVD or VCR with the
remote control
ENG
• You can use DVD (VCR) POWER, VOLUME, PLAY, PAUSE,
STOP, SKIP, MENU and Numeric button (0~9).
• The remote control may not work on some brands of DVD (VCR).
Also, some operations may not be possible depending on your brand of DVD
(VCR).
• The remote control will work with Samsung DVD (VCR) by default.
43
2007-12-10 오후 5:24:10
Operating your DVD or VCR with the
remote control (cont’d)
VCR Brand Code List
Brand
ADMIRAL (M.WARDS)
AWIA
AKAI
ANAM
AOC
AUDIO DYNAMIC
BELL & HOWELL (M.WARDS)
BROKSONIC
CANON
CAPEHART
CITIZEN
CRAIG
CRITERION
CURTIS MATHES
DAEWOO
DAYTRON
DBX
EMERSON
FISHER
FUNAI
GENERAL ELECTRIC (GE)
GO VIDEO
HARMAN KARDON
HITACHI
JVC
KENWOOD
LG (GOLDSTAR)
LXI (SEARS)
MAGIN
MAGNAVOX
MARANTZ
MARTA
043, 106
044, 045, 046
088, 089, 090
001, 002, 003, 004, 005,
033
091
019, 047, 092
048, 093
092, 094, 095
001, 033, 049, 091
011
050
050, 072, 096
051
001, 031, 032, 033, 044,
091
006, 007, 008, 009, 010,
011, 012, 013, 014, 015,
016, 017, 018, 046, 051,
091
011
019, 047, 052, 092
025, 031, 032, 044, 046,
094, 095, 097, 098, 099
009, 048, 053, 054, 055,
100
044
001, 031, 032, 033, 056,
091
059, 060, 061
019
020, 021, 049, 054, 062,
100
051
001, 033, 049, 091
001, 033
025
047, 048, 052, 062, 091,
092
001, 033, 047, 052, 063,
064, 065, 092
047, 050, 052, 092
019, 020, 021, 022, 023,
024, 025, 026, 027, 028,
029, 030, 050
020, 025, 044, 048, 050,
053, 054, 055, 062, 100
072
001, 031, 032, 033, 049,
066, 067, 091
001, 019, 033, 047, 052,
092, 110
025, 050
44
AV-R720-ENG-비유럽향.indb 44-45
Brand
MEI
MEMOREX
MINOLTA
MITSUBISHI/MGA
MTC
MULTITECH
NEC
OLYMPIC
OPTIMUS
ORION
PANASONIC
PENNEY
PENTAX
PHILCO
PHILIPS
PILOT
PIONEER
PORTLAND
QUASAR
RICO
RCA/PROSCAN
REALISTIC
SAMSUNG
SANYO
SANSUI
SCOTT
SEARS
SHARP
SINGER
SIGNATURE 2000 (M.WARDS)
SHINTOM
SONY
STS
SYLVANIA
SYMPHONIC
TANDY
Code Number
001, 033
001, 025, 033, 054, 091,
100
020, 021, 062
068, 069, 070, 101, 102
072
044, 057, 069
019, 047, 052, 057, 092
049, 091
101
103
001, 004, 033, 049, 067,
091, 107
019, 020, 072
001, 020, 021, 033, 062
001, 033, 046, 049, 091,
094
001, 030, 033, 049, 050,
066, 091
025
049
011
001, 033, 049, 067, 091,
107, 108
036
001, 020, 021, 031, 032,
033, 049, 051, 062, 066,
070, 091, 104
001, 009, 025, 033 ,
044, 048, 054, 091,
101, 105
000, 006, 031, 032, 057,
058, 071, 072, 073, 074,
075, 076, 077, 078, 079,
080, 081
008, 009, 046, 048, 050,
054, 058, 093, 100
092
006, 051, 054, 057, 069,
070, 100, 101
020, 021, 025
043, 105, 106
096
043, 044, 054, 100, 106
096
034, 035, 036, 037, 038,
039, 040, 041, 042, 082,
083, 084, 085, 086
020
001, 033, 044, 049, 066,
091
044
009
Brand
TASHIRO
TATUNG
TEAC
TECHNICS
TEKNIKA
TOSHIBA
TOTEVISION
TAEKWANG
UNITECH
VECTOR RESEARCH
VIDEO CONCEPTS
VIDEOSONIC
WARDS
YAMAHA
ZENITH
Code Number
050
047, 052, 092
044, 047, 052, 092
001, 033, 049, 091
001, 025, 033
006, 051
025, 072
087
072
019
019
072
001, 020, 031, 032, 033,
043, 050, 054, 072, 100,
105, 106, 109
019, 047,048, 052, 092,
019, 047, 048, 052, 092
DVD Brand Code List
Brand
DENON
DOONOON
DMTECH
FISHER
GE
HARMAN/KARDON
JVC
KENWOOD
LG
MAGNAVOX
MITSUBISHI
ONKYO
OPTIMUS
PANASONIC
PROSCAN
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SONY
THETA DIGITAL
TOSHIBA
YAMAHA
ZENITH
TAEGWANG
PS2
X-BOX
APEX
MARANTZ
Code Number
003, 032
019
017
002
006
012
010, 013
008
001
004
005, 016
004, 014
011
021
006
004, 023
007, 011, 022, 025
006
000, 027
002
015, 020
011
004, 018
009, 033
004, 024
026
028
029
030
031
Before calling for service
Symptom
The unit will not turn on.
A function does not work
when the button is pressed.
Sound is not produced.
Picture does not appear on a TV
when the function is selected.
Remote controller does
not work.
The sound from the
left/right channels is
reversed.
Can't receive radio
broadcasts.
There is no sound from
surround speakers.
There is no sound from
centre speaker
Check
Remedy
• Is the power cord plugged into the
outlet?
• Connect the power plug to the outlet.
• Is there static electricity in the air?
• Disconnect the power plug and
connect it again.
• Are the speakers and external
components connected properly?
• Is the Mute function on?
• Is the volume set to minimum?
• Is the speaker setup set
incorrectly to NONE?
• Do you see the message of “NOT
SUPPORT” in playing a MPEG
audio file?
• Connect them correctly.
• Is the external component
connected properly?
• Connect it correctly.
• Are the batteries drained?
• Is the distance between remote
control and main unit too great?
• Replace with new batteries.
• Operate at close distance.
• Are the left/right speaker or
left/right input/output cables
connected properly?
• Check the left/right channel and
connect it/them correctly.
• Is FM antenna connected
properly?
• Connect the antenna correctly.
• If the input strength of antenna signal
is weak, install the FM antenna in a
place with good reception.
• Is the surround speaker
connected properly?
• Is SURR (surround) incorrectly
set to NONE in speaker setup?
• Is surround mode set to stereo?
• Refer to pages 12~13 to connect
them properly.
• Refer to pages 20~21 to select
LARGE or SMALL.
• Refer to pages 29~35 to select
proper Surround Mode.
• Is the centre speaker connected
properly?
• Is CEN (centre) incorrectly selected
to NONE in speaker setup?
• Is the surround mode selected to
stereo?
• Refer to pages 10~11 to connect it
properly.
• Refer to pages 20~21 to select
LARGE or SMALL.
• Refer to pages 29~35 to select other
Surround Modes.
• Press Mute button to cancel the function.
• Adjust the volume.
• Refer to pages 20~21 to select
LARGE, SMALL or YES.
• The file format of MPEG is not
supported. Change the audio format
of the source device (Blu-RAY
Player) to PCM.
MISCELLANEOUS
HQ
INSTANT REPLAY
JCL
JCP
JC PENNY
Code Number
ENG
45
2007-12-10 오후 5:24:12
Specifications
Before calling for service
(cont’d)
Check
Symptom
There is no sound from
surround back speakers
Can't select EX/ES mode.
Can't select Dolby Pro
Logic llx mode.
Can't select NEO:6 mode.
There is no sound when
playing a DTS encoded
DVD.
Remedy
• Are the surround back speakers
connected properly?
• Is the S.BACK(Surround Back)
selected to NONE in Speaker
Setup?
• Is Surround Mode set to EX/ES?
• Refer to pages 10~11 to connect it
properly.
• Refer to pages 20~21 to select
LARGE or SMALL.
• Is S.BACK(Surround Back)
selected to NONE in Speaker
Setup?
• Is the input signal selected
properly?
• Refer to pages 20~21 to select
LARGE or SMALL.
• Is the input signal selected
properly?
• Select 2 channel Dolby Digital, PCM,
and Analogue input signal.
• Is the input signal selected
properly?
• Use PCM and Analogue input signal.
• Is Digital input selected?
• Check whether the DVD player is
properly connected and refer to page
24 to select the digital input.
GENERAL
• Refer to page 32 to set Surround
Mode to EX/ES.
FM TUNER
• Use 7.1 channel external
component.
AMPLIFIER
FREQUENCY
RESPONSE
VIDEO
OUTPUT
• The protection function will come on if the main unit or power
transformer overheats.
"
" will appear in the display.
This function will come on :
- If speaker terminal is shorted
• If PROTECTION appears on the display,
check whether the speaker terminal is shorted
and then turn on the unit
SPEAKE
RS
Standby power consumption
Power consumption Main unit
Subwoofer
Weight
Dimensions (W x H x D)
Operating temperature range
Operating humidity range
Frequency response
Usable sensitivity
S/N ratio
Distortion
Stereo separation
Tuner output level
Rated output
Front speaker(left+right)
Center speaker
Surround speaker(left+right)
Surround back
Input sensitivity/impedance
S/N ratio (analog input)
Separation (1kHz)
Analog input
Digital input/96kHz PCM
TV format
Input level/impedance
Output level/impedance
Video frequency response
S/N ratio
Speaker system
Front / Surround , Surround back
Impedance
4Ω x 6
Rated input
100W
Maximum input
200W
Dimensions (W x H x D) 210x1000x271mm/169x300x129mm
Weight
11.8 Kg / 2.6 Kg
0.9W
100W
90W
5.8 kg
430 x 145 x 350 mm
+5°C~+35°C
10%~75%
87.5~108.0MHz
12dBf
MONO/STEREO 55/55dB
MONO/STEREO 0.3/0.8%
30dB
1kHz, 75kHz Dev
20Hz~20kHz/THD = 10%
4 Ω 100W/CH
4 Ω 100W/CH
4 Ω 100W/CH
4 Ω 100W/CH
450mV/47kΩ
80dB
60dB
20Hz~20kHz(±3dB)
20Hz ~44kHz(±3dB)
NTSC/PAL
1Vp-p/75 Ω
1Vp-p/75 Ω
5Hz to 10kHz(-3dB)
60dB
MISCELLANEOUS
Product protection function
Heat protection
ENG
Centre
Subwoofer speaker
4Ω
8Ω
100W
150W
200W
300W
450 x 221 x 234 mm 311 x 375 x 422 mm
6.7Kg
13.6 Kg
S/N ratio, distortion, separation and usable sensitivity are based on measurement using AES (Audio Engineering Society) guidelines.
- If speaker cable is shorted If there is no problem when you turn
the unit on again after turning it off, PROTECTION mark will
disappear on the display and the unit will work properly.
46
AV-R720-ENG-비유럽향.indb 46-47
47
2007-12-10 오후 5:24:14
48
AV-R720-ENG-비유럽향.indb 48
2007-12-10 오후 5:24:16
Download PDF

advertising