Sony | KDL-46X2000 | Sony KDL-46X2000 Operating Instructions

2-678-257-12(3)
LCD Digital Colour TV
Operating Instructions
Before operating the TV, please read the “Safety
information” section of this manual.
Retain this manual for future reference.
KDL-46X2000
For useful information about Sony products
© 2006 Sony Corporation
NOTICE FOR
CUSTOMERS IN THE
UNITED KINGDOM
A moulded plug complying with BS1363 is fitted to this
equipment for your safety and convenience.
Should the fuse in the plug supplied need to be replaced, a 13
AMP fuse approved by ASTA or BSI to BS 1362 (i.e.,
marked with
or ) must be used.
When an alternative type of plug is used it should be fitted
with a 13 AMP FUSE, otherwise the circuit should be
protected by a 13 AMP FUSE at the distribution board.
If the plug supplied with this equipment has a detachable fuse
cover, be sure to attach the fuse cover after you change the
fuse. Never use the plug without the fuse cover. If you should
lose the fuse cover, please contact your nearest Sony service
station.
FUSE
How to replace the fuse
Open the fuse compartment with a blade screwdriver, and
replace the fuse.
2 GB
Introduction
Thank you for choosing this Sony product.
Before operating the TV, please read this manual
thoroughly and retain it for future reference.
Notice for Digital TV function
• Any functions related to Digital TV (with
logo) will
only work in countries or areas where DVB-T (MPEG2)
digital terrestrial signals are broadcasted. Please confirm
with your local dealer if you can receive a DVB-T signal
where you live.
• Although this TV set follows DVB-T specifications,
compatibility with future DVB-T digital terrestrial
broadcasts cannot be guaranteed.
• Some Digital TV functions may not be available in some
countries.
Trademark information
•
is a registered trademark of the DVB Project
• Manufactured under license from BBE Sound, Inc.
Licensed by BBE Sound, Inc. under one or more of the
following US patents: 5510752, 5736897. BBE and BBE
symbol are registered trademarks of BBE Sound, Inc.
• “Dolby”, “Pro Logic”, and the double-D symbol are
trademarks of Dolby Laboratories.
• Manufactured under license from Dolby Laboratories.
• TruSurround technology is used as a virtualizer for Dolby
Virtual Surround.
• TruSurround, SRS and (z) symbol are trademarks of SRS
Labs, Inc.
TruSurround technology is incorporated under license
from SRS Labs, Inc.
•
HDMI, the HDMI logo and
High-Definition Multimedia
Interface are trademarks or registered trademarks of
HDMI Licensing, LLC.
Table of Contents
Start-up Guide
4
Safety information .....................................................................................................................8
Precautions .............................................................................................................................11
Overview of the remote ........................................................................................................12
Overview of the TV buttons and indicators ........................................................................14
Watching TV
Watching TV............................................................................................................................15
Checking the Digital Electronic Programme Guide (EPG)
.............................................18
Using the Digital Favourite list
.......................................................................................20
Viewing pictures from connected equipment ..........................................................................21
Using MENU Functions
Navigating through menus ......................................................................................................22
Picture menu ...........................................................................................................................23
Sound menu............................................................................................................................26
Screen menu...........................................................................................................................27
Set-up menu............................................................................................................................29
AV Set-up menu......................................................................................................................31
Analogue Set-up menu ...........................................................................................................32
Digital Set-up menu
.......................................................................................................35
PC Settings menu ...................................................................................................................37
Using Optional Equipment
Connecting optional equipment...............................................................................................39
Programming the remote ........................................................................................................41
Additional Information
Specifications ..........................................................................................................................43
Troubleshooting ......................................................................................................................45
Index .......................................................................................................................................47
: for digital channels only
3 GB
Start-up Guide
To insert batteries into the remote
1: Checking the
accessories
Remote RM-ED006 (1)
Size AA batteries (R6 type) (2)
Mains lead (Type BF) (1)
Notes
Coaxial cable (1)
Do not remove these ferrite cores.
PC cable (1)
Do not remove these ferrite cores.
Cable holder (1)
Support belt (1) and screws (2)
4 GB
• Observe the correct polarity when inserting batteries.
• Dispose of batteries in an environmentally friendly way.
Certain regions may regulate disposal of the battery.
Please consult your local authority.
• Do not use different types of batteries together or mix old
and new batteries.
• Handle the remote with care. Do not drop or step on it, or
spill liquid of any kind onto it.
• Do not place the remote in a location near a heat source, or
in a place subject to direct sunlight, or in a damp room.
3: Preventing the TV
from toppling over
Start-up Guide
2: Connecting an aerial/
VCR
Connecting an aerial only
Coaxial cable
(supplied)
Mains lead (supplied)
2
Connecting an aerial and VCR
3
1
Mains lead
(supplied)
Coaxial cable
(supplied)
4: Bundling the cables
Scart lead (not supplied)
Coaxial cable
(not supplied)
VCR
5 GB
When the TV is in standby mode (the 1 (standby)
indicator on the TV (front) is red), press TV "/1
on the remote to switch on the TV.
5: Selecting the
language and country/
region
3
Press F/f/G/g to select the language
displayed on the menu screens, then press
.
2
4
Press F/f to select the country/region in
which you will operate the TV, then press
.
1
2
If the country/region in which you want to use the
TV does not appear in the list, select “-” instead of
a country/region.
The message confirming the TV start auto-tuning
appears on the screen, then go to “6: Auto-tuning
the TV”.
3,4
3,4
1
Connect the TV to your mains socket
(220-240 V AC, 50 Hz).
2
Press 1 on the TV (right side).
When you switch on the TV for the first time, the
Language menu appears on the screen.
6 GB
3
When the Programme Sorting menu
appears on the screen, follow the steps of
“Programme Sorting” (page 32).
If you do not change the order in which the analogue
channels are stored on the TV, go to step 4.
The TV will search for and store all available TV
channels.
4
Press MENU to exit.
The TV has now tuned in all the available channels.
Note
When a digital broadcast channel cannot be received, or
when selecting a region in which there are no digital
broadcasts in step 4 (page 6) under “5: Selecting the
language and country/region”, the time must be set after
performing step 3.
2
2
4
1
Before you start auto-tuning the TV, insert
a pre-recorded tape into the VCR
connected to the TV (page 5) and start play
back.
The video channel will be located and stored on
the TV during auto-tuning.
If no VCR is connected to the TV, skip this step.
2
Press G to select “OK”, then press
.
The TV starts searching for all available digital
channels, followed by all available analogue
channels. This may take some time, please be
patient and do not press any buttons on the TV or
remote.
If a message appears for you to confirm the aerial
connection
No digital or analogue channels were found.
Check the aerial connection and press G to select
“Yes”, then press
to start auto-tuning again.
7 GB
Start-up Guide
6: Auto-tuning the TV
Safety information
Mains lead
• Observe the followings to prevent the mains lead being
damaged. If the mains lead is damaged, it may result in a
fire or an electric shock.
– Unplug the mains
lead when moving
the TV set.
– When you
disconnect the mains
lead, disconnect it
from the mains
socket first.
– Be sure to grasp the plug when
disconnecting the mains lead. Do
not pull on the mains lead itself.
– Do not pinch, bend, or twist the
mains lead excessively. The core
conductors may be exposed or
broken.
– Do not modify the mains lead.
– Do not put anything heavy on the
mains lead.
– Keep the mains lead away from heat
sources.
• If you damage the mains lead, stop
using it and ask your dealer or Sony service centre to
exchange it.
• Do not use the supplied mains lead on any other
equipment.
• Use only an original Sony mains lead, not other brands.
Mains socket
• The TV set with a three-wire grounding
type mains plug must be connected to a
mains socket with a protective earthing
connection.
• Do not use a poor fitting mains socket.
Insert the plug fully into the mains socket.
A poor fit may cause arcing and result in a
fire. Contact your electrician to have the
mains socket changed.
Cleaning the mains plug
Unplug the mains plug and clean it
regularly. If the plug is covered with dust
and it picks up moisture, its insulation may
deteriorate and result in a fire.
Overloading
This TV set is designed to operate on
a 220–240 V AC supply only. Take
care not to connect too many
appliances to the same mains socket
as this could result in a fire or an electric shock.
When not in use
If you will not be using the TV set
for several days, the TV set
should be disconnected from the
mains for environmental and
safety reasons. However, some TV sets may have features
8 GB
which need the TV set to be left in standby to work correctly.
The instructions in this manual will inform you if this
applies.
Carrying
• Before carrying the TV set, disconnect all the cables from
the TV set.
• Carrying the large size TV set requires two or more
people.
• When you carry the TV set by hand,
hold the TV set as illustrated on the
right. If you do not do so, the TV set
may fall and be damaged or cause
serious injury.
• When transporting it, do not subject
the TV set to jolts or excessive
vibration. The TV set may fall and be damaged or cause
serious injury.
• If the TV set has been dropped or damaged, have it
checked immediately by qualified service personnel.
• When you carry the TV set in for repair or when you move
it, pack it using the original carton and packing material.
Handling
When lifting the TV set or
moving the panel of the TV set,
hold it firmly as illustrated on
the right.
Placement
• The TV set should be
installed near an easily accessible mains socket.
• Place the TV set on a stable, level surface.
Do not hang anything on the TV set. If
you do, the TV set may fall from the
stand, causing damage or serious injury.
• Do not install the TV set in places subject
to extreme temperature, for example in
direct sunlight, or near a radiator, or heating vent. If the
TV set is exposed to extreme temperature, the TV set may
overheat and cause deformation of the casing or cause the
TV set to malfunction.
• Do not install the TV set in a place exposed to direct air
conditioning. If the TV set is installed in such a location,
moisture may condense inside and may cause a
malfunction.
• Never place the TV set in hot, humid
or excessively dusty places.
• Do not install the TV set where
insects may enter.
• Do not install the TV set where it
may be exposed to mechanical vibration.
• Do not install the TV set in a location where it may
protrude, such as on or behind a pillar, or where you might
bump your head on it. Otherwise, it may result in injury.
• Do not allow children to climb on the TV
set.
• If you use the TV set near the seashore,
salt may corrode metal parts of the TV set
and cause internal damage or fire.
Ventilation
• Never cover the ventilation
holes in the cabinet. It may
cause overheating and result in a
fire.
• Unless proper ventilation is provided, the TV set may
gather dust and get dirty. For proper ventilation, observe
the following:
– Do not install the TV set turned backwards or sideways.
– Do not install the TV set turned over or upside down.
– Do not install the TV set on a shelf or in a closet.
– Do not place the TV set on a rug or bed.
– Do not cover the TV set with cloth, such as curtains, or
items such as newspapers, etc.
• Leave some space around the TV set. Otherwise, aircirculation may be inadequate and cause overheating,
which may cause a fire or damage to the TV set.
30 cm
10 cm
10 cm
6 cm
Leave at least this much space.
• When installing the TV set on the wall, leave at least
10 cm space from the bottom.
• Never install the TV set as follows:
Air circulation
is blocked.
Wall
Air circulation
is blocked.
Wall
• If the TV set is to be installed on
a wall, have the installation
carried out by qualified service
personnel. Improper installation
may render the TV set unsafe.
Wiring
• When hooking up, be sure to unplug the mains lead for
your safety.
• The TV set is not disconnected from the mains when the
TV set is switched off. To disconnect the TV set
completely, pull the plug from the mains.
• Take care not to catch your feet on the cables. It may
damage the TV set.
Medical institutions
Do not place this TV set in a place
where medical equipment is in
use. It may cause a malfunction of
medical instruments.
Outdoor use
• Do not install this TV set
outdoors. If the TV set is
exposed to rain, it may result in a
fire or an electric shock.
• If this TV set is exposed to direct
sunlight, the TV set may heat up
and it may damage the TV set.
Vehicle, Ships and other
vessels
• Do not install this TV set in a
vehicle. The motion of the
vehicle may cause the TV set to
fall down and cause injury.
• Do not install this TV set on a
ship or other vessel. If the TV set
is exposed to seawater, it may
cause a fire or damage the TV
set.
Ventilation holes
Do not insert anything in the ventilation
holes. If metal or liquid is inserted in these
holes, it may result in a fire or an electric
shock.
Optional accessories
Observe the following when installing the TV set using a
stand or wall-mount bracket. If you do not do so, the TV set
may fall and cause serious injury.
• It is strongly recommended that you use Sony accessories
for safety reasons:
– Wall-mount bracket SU-WL51
– TV stand SU-FL61
• It is strongly recommended that you use the official Sony
wall-mount bracket to allow adequate air circulation and
to avoid dust build up around the TV, wall and ceiling.
• Secure the TV set properly, following the instructions
supplied with your stand or wall-mount bracket when
installing the TV set.
• Be sure to attach the brackets supplied with your stand.
Water and moisture
• Do not use this TV set near water
– for example, near a bathtub or
shower room. Also do not expose
to rain, moisture or smoke. This
may result in a fire or an electric shock.
• Do not touch the mains lead and the TV
set with wet hands. Doing so may cause
an electric shock or damage to the TV
set.
Continued
9 GB
Moisture and flammable objects
• Do not place any objects on the TV
set. The TV set shall not be exposed to
dripping or splashing and that no
objects filled with liquid, such as
vases, shall be placed on the TV set.
• To prevent fire, keep flammable
objects or naked lights (e.g. candles)
away from the TV set.
• If any liquid or solid object does fall through openings in
the cabinet, do not operate the TV set. It may result in an
electric shock or damage to the TV set. Have it checked
immediately by qualified service personnel.
Oils
Do not install this TV set in restaurants that use oil. Dust
absorbing oil may enter and damage the TV set.
Lightning storms
For your own safety, do not touch any
part of the TV set, mains lead, or
aerial lead during lightning storms.
Broken pieces
• Do not throw anything at the TV set.
The screen glass may break by the
impact and cause serious injury.
• If the surface of the TV set cracks, do
not touch it until you have unplugged the mains lead.
Otherwise electric shock may result.
Servicing
Dangerously high voltages are
present inside the TV set.
Do not open the cabinet. Entrust the
TV set to qualified service personnel
only.
Small accessories removal and fittable
Keep accessories out of children’s reach. If they are
swallowed, choking or suffocation may occur. Call a doctor
immediately.
Replacing the bezel unit
The bezel unit can be replaced with others that are sold
separately. However, do not remove the unit except to
replace it. For details, see the instructions supplied with bezel
units.
10 GB
Precautions
Viewing the TV
• To view the TV comfortably, the recommended viewing
position is from four to seven times the screen’s vertical
length away from the TV set.
• To obtain a clear picture, do not expose the screen to direct
illumination or direct sunlight. If possible, use spot
lighting directed down from the ceiling.
• View the TV in moderate light, as viewing the TV in poor
light strains your eyes. Watching the screen continuously
for long periods of time can also strain your eyes.
• If the angle of the TV set is to be adjusted, steady the base
of the stand with your hand to prevent the TV set from
becoming separated from the stand. Be careful not to get
your fingers caught between the TV set and the stand.
Volume adjustment
• Adjust the volume so as not to trouble your neighbours.
Sound carries very easily at night time. Therefore, closing
the windows or using headphones is suggested.
• When using headphones, adjust the volume so as to avoid
excessive levels, as hearing damage may result.
LCD Screen
• Although the LCD screen is made with high-precision
technology and 99.99% or more of the pixels are effective,
black dots may appear or bright points of light (red, blue,
or green) may appear constantly on the LCD screen. This
is a structural property of the LCD screen and is not a
malfunction.
• Do not expose the LCD screen surface to the sun. Doing
so may damage the screen surface.
• Do not push or scratch the front filter, or place objects on
top of this TV set. The image may be uneven or the LCD
screen may be damaged.
• If this TV set is used in a cold place, a smear may occur in
the picture or the picture may become dark. This does not
indicate a failure. These phenomena disappear as the
temperature rises.
• Ghosting may occur when still pictures are displayed
continuously. It may disappear after a few moments.
• The screen and cabinet get warm when this TV set is in
use. This is not a malfunction.
• The LCD screen contains a small amount of liquid crystal
and mercury. The fluorescent tube used in this TV set also
contains mercury. Follow your local ordinances and
regulations for disposal.
Handling and cleaning the screen surface/cabinet of
the TV set
Be sure to unplug the mains lead connected to the TV set
from AC mains socket before cleaning.
To avoid material degradation or screen coating degradation,
observe the following precautions.
• Do not push on the screen, scratch it with a hard object, or
throw anything at it. The screen may be damaged.
• Do not touch the display panel after operating the TV set
continuously for a long period as the display panel
becomes hot.
• We recommend that the screen surface be touched as little
as possible.
• To remove dust from the screen surface/cabinet, wipe
gently with a soft cloth. If dust is persistent, wipe with a
soft cloth slightly moistened with a diluted mild detergent
solution.
• Never use any type of abrasive pad, alkaline/acid cleaner,
scouring powder, or volatile solvent, such as alcohol,
benzene, thinner or insecticide. Using such materials or
maintaining prolonged contact with rubber or vinyl
materials may result in damage to the screen surface and
cabinet material.
• The ventilation holes can accumulate dust over time. To
ensure proper ventilation, we recommend removing the
dust periodically (once a month) using a vacuum cleaner.
Optional Equipments
• Do not install optional components too close to the TV set.
Keep optional components at least 30 cm away from the
TV set. If a VCR is installed in front of the TV set or
beside the TV set, the picture may become distorted.
• Picture distortion and/or noisy sound may occur if the TV
set is positioned in close proximity to any equipment
emitting electromagnetic radiation.
Disposal of the TV set
Disposal of Old Electrical &
Electronic Equipment
(Applicable in the European
Union and other European
countries with separate
collection systems)
This symbol on the product or on
its packaging indicates that this
product shall not be treated as
household waste. Instead it shall
be handed over to the applicable
collection point for the recycling
of electrical and electronic equipment. By ensuring this
product is disposed of correctly, you will help prevent
potential negative consequences for the environment and
human health, which could otherwise be caused by
inappropriate waste handling of this product. The recycling
of materials will help to conserve natural resources. For more
detailed information about recycling of this product, please
contact your local Civic Office, your household waste
disposal service or the shop where you purchased the
product.
11 GB
Overview of the remote
1 TV "/1 – TV standby
Switches off the TV temporarily and on from standby mode.
2 Number buttons
• In TV mode: Selects channels. For channel numbers 10 and above, enter
the second and third digit within two seconds.
• In Analogue Text mode: Enters the three digit page number to select the
page.
3
– Previous channel
Returns to the previous channel watched (for more than five seconds).
4
– Screen mode (page 16)
5
– Picture freeze (page 16)
Freezes the TV picture.
6
/
– Info / Text reveal
• In digital mode: Displays brief details of the programme currently being
watched.
• In analogue mode: Displays information such as current channel number
and screen mode.
• In Analogue Text mode (page 16): Reveals hidden information (e.g.
answers to a quiz).
7
F/f/G/g/
(page 15, 22)
8 TOOLS (page 17, 21)
Enables you to access various viewing options and change/make adjustments
according to the source and screen mode.
9 MENU (page 22)
0 PROG +/- (page 15)
• In TV mode: Selects the next (+) or previous (-) channel.
• In Analogue Text mode: Selects the next (+) or previous (-) page.
qa % – Mute (page 15)
qs 2 +/- – Volume
qd RETURN /
Returns to the previous screen of any displayed menu.
qf
– EPG (Digital Electronic Programme Guide) (page 18)
qg Coloured buttons (page 16, 18, 20)
qh ANALOG – Analogue mode (page 15)
qj DIGITAL – Digital mode (page 15)
qk / – Text (page 16)
ql
/
– Input select / Text hold
• In TV mode (page 21): Selects the input source from equipment connected
to the TV sockets.
• In Analogue Text mode (page 16): Holds the current page.
w; A/B – Dual Sound (page 26)
12 GB
wa "/1
Switches on or off the optional equipment selected from the function buttons.
ws Function buttons
Enables you to operate the corresponding equipment. For details, see
“Programming the remote” on page 41.
wd DVD/VCR operating buttons
• . : Replays the current programme from the previous chapter mark (if
any).
• > : Advances forward to the next chapter mark (if any).
•
: Replays the current programme for a set period of time.
•
: Advances forward a set period of time.
• m : Plays a programme in fast reverse mode.
• M : Plays a programme in fast forward mode.
• H : Plays a programme at a normal speed.
• X : Pauses playback.
• x : Stops the playback.
• VISUAL SEARCH : Only for Sony DVD recorders with the visual search
function. For details, see the operating instructions supplied with the DVD
recorder.
wf DVD/VCR record buttons
• z REC: Starts recording.
• X REC PAUSE: Pauses the recording.
• x REC STOP: Stops the recording.
X REC PAUSE and x REC STOP are available only on DVD recorders.
wg F1/F2
• Selects a disc when using a DVD changer.
• Selects a function when using a combination unit (e.g. a DVD/VCR).
For details, see the operating instructions supplied with the DVD changer or
combination unit.
wh DVD MENU
Displays the DVD disc menu.
wj DVD TOP MENU
Displays the top menu of the DVD disc.
Tip
The number 5, H, PROG + and A/B buttons have tactile dots. Use the tactile dots as
references when operating the TV.
13 GB
Overview of the TV buttons and indicators
1 1 – Power
Switches the TV on or off.
PROG
2 PROG +/-/
/
• In TV mode: Selects the next (+) or previous
(-) channel.
• In TV menu: Moves through the options up
( ) or down ( ).
3 2 +/-/
/
• In TV mode: Increases (+) or decreases (-) the
volume.
• In TV menu: Moves through the options right
( ) or left ( ).
MENU
4
/
– Input select/OK
• In TV mode (page 21): Selects the input
source from equipment connected to the TV
sockets.
• In TV menu: Selects the menu or option, and
confirms the setting.
5
6
(page 22)
– Picture Off/Timer indicator
• Lights up in green when the picture is
switched off (page 29).
• Lights up in orange when the timer is set
(page 29).
7 1 – Standby indicator
Lights up in red when the TV is in standby mode.
8 " – Power indicator
Lights up in green when the TV is switched on.
9 Remote control sensor
Note
Make sure that the TV is completely switched off before unplugging the mains lead. Unplugging the mains lead while the TV is
turned on may cause the indicator to remain lit or may cause the TV to malfunction.
14 GB
Watching TV
Watching TV
3
: Interactive service is available (Digital Text)
: Radio service
: Scrambled/Subscription service
: Multiple audio languages available
: Subtitles available
: Subtitles available for the hearing impaired
: Recommended minimum age for current
programme (from 4 to 18 years)
: Parental Lock
: Current programme is being recorded
3
Additional operations
2
3
Press 1 on the TV (right side) to switch on
the TV.
To
Do this
Switch off the TV
temporarily
(standby mode)
Press TV "/1.
Switch off the TV
completely
Press 1 on the TV (right side).
Switch on the TV
without sound from
standby mode
Press %. Press 2 +/- to adjust
the volume.
Adjust the volume
Press 2 + (increase)/
- (decrease).
Mute the sound
Press %. Press again to restore.
Access the
Programme index
table (in analogue
mode only)
Press
. To select an analogue
channel, press F/f, then press
.
To access the Input signal index
table, see page 21.
When the TV is in standby mode (the 1 (standby)
indicator on the TV (front) is red), press TV "/1
on the remote to switch on the TV.
2
Press DIGITAL to switch to digital mode or
ANALOG to switch to analogue mode.
The channels available vary depending on the
mode.
Continued
15 GB
Watching TV
To select channel numbers 10 and above using the
number buttons, enter the second and third digits
within two seconds.
To select a digital channel using the Digital
Electronic Programme Guide (EPG), see page 18.
In digital mode
An information banner appears briefly. The
following icons may be indicated on the banner.
1
1
Press the number buttons or PROG +/- to
select a TV channel.
To access Digital Text
Many broadcasters provide a Digital Text service.
Digital Text offers graphically rich contents,
compared to Analogue Text.
Select a digital channel which provides Digital Text,
then press /.
When a broadcaster provides a dedicated Digital Text
channel, select this channel to access Digital Text.
To navigate through Digital Text, follow the
instructions on the screen.
To exit Digital Text, press RETURN.
To move around, press F/f/G/g.
To select items, press
and the number buttons.
To access shortcuts, press the coloured buttons.
To access Analogue Text
In analogue mode, press /. Each time you press /,
the display changes cyclically as follows:
Text and TV picture t Text t No Text (exit the
Text service)
To select a page, press the number buttons or PROG
+/-.
To hold a page, press
/ .
To reveal hidden information, press
/ .
To jump a page, press
and F/f, then press
(for
three digit pages).
To change the screen mode manually to
suit the broadcast
Press
repeatedly to select Smart, 4:3, Wide,
Zoom, or 14:9.
Smart*
Displays conventional 4:3 broadcasts with an
imitation wide screen effect. The 4:3 picture is
stretched to fill the screen.
4:3
Displays conventional 4:3 broadcasts (e.g. non-wide
screen TV) in the correct proportions.
Wide
Tips
• Ensure that the TV is receiving a good signal, or some text
errors may occur.
• Most TV channels broadcast a Text service. For
information on the use of the service, select the index
page.
• When four coloured items appear at the bottom of the Text
page, Fastext is available. Fastext allows you to access
pages quickly and easily. Press the corresponding
coloured button to access the page.
Displays wide screen (16:9) broadcasts in the correct
proportions.
To freeze the picture – Picture freeze
Displays cinemascopic (letter box format) broadcasts
in the correct proportions.
You can freeze the current picture to make a note of a
telephone number or recipe.
1
Press
Zoom*
14:9*
.
The frozen picture is displayed on the right of the
screen. You can watch a moving picture on the
left.
2
Press
mode.
again to return to normal TV
Displays 14:9 broadcasts in the correct proportions.
As a result, black border areas are visible on the
screen.
* Parts of the top and bottom of the picture may be cut off.
Tips
• Alternatively, you can set “Auto Format” to “On”. The TV
will automatically select the best mode to suit the
broadcast (page 27).
• You can adjust the position of the picture when selecting
Smart, 14:9 or Zoom. Press F/f to move up or down
(e.g. to read subtitles).
16 GB
To use the Tools menu
Press TOOLS to display the following options when
viewing a TV programme.
Options
Description
Close
Closes the Tools menu.
PAP (or Single Picture) See page 17.
See page 23.
Sound Mode
See page 26.
Subtitle Setting (in
digital mode only)
See page 35.
Digital Favourites (in
digital mode only)
See page 20.
Power Saving
See page 29.
Sleep Timer
See page 29.
i Volume*
See page 30.
Auto Clock Set (in
analogue mode only)
Allows you to switch to digital
mode and obtain the time.
Watching TV
Picture Mode
* This option appears only if “i Speaker Link” is set to
“Off” (page 30).
To view two pictures simultaneously – PAP
(Picture and Picture)
You can view two pictures (external input and TV
programme) on the screen simultaneously.
Connect the optional equipment (page 39), and make
sure that images from the equipment appear on the
screen (page 21).
Notes
• This function is not available for a PC input source.
• You cannot change the size of the pictures.
Press F/f to select “PAP” from the Tools menu, then
press . The picture from the connected equipment
is displayed on the left and the TV programme is
displayed on the right.
To return to normal TV mode, press
or RETURN.
Tips
• You can also return to normal TV mode by selecting
“Single Picture” from the Tools menu.
• The picture framed in green is audible. You can switch the
audible picture by pressing G/g.
17 GB
Checking the Digital Electronic Programme Guide
(EPG)
*
1
In digital mode, press
to display the
Digital Electronic Programme Guide
(EPG).
2
Perform the desired operation, as shown in
the following table.
Note
Programme information will only be displayed if the TV
station is transmitting it.
Digital Electronic Programme Guide (EPG)
* This function may not be available in some countries.
To
Do this
Turn off the EPG
Press
Move through the EPG
Press F/f/G/g.
Watch a current programme
Press
Sort the programme information by
category – Category list
1
2
.
while the current programme is selected.
Press the blue button.
Press F/f/G/g to select a category. The category name is
displayed on the side.
The categories available include:
“Favourite”: Contains all the channels that have been stored in the
Favourite list (page 20).
“All Categories”: Contains all available channels.
“News”: Contains all news channels.
3
Press
.
The Digital Electronic Programme Guide (EPG) now only displays the
current programmes from the category selected.
Set a programme to be recorded – Timer
REC
1
2
3
4
Press F/f/G/g to select the future programme you want to
record.
Press .
Press F/f to select “Timer REC”.
Press
to set the TV and your VCR timers.
A
symbol appears by that programme’s information. The
indicator on the TV (front) lights up.
Notes
• You can set VCR timer recording on the TV only for Smartlink compatible
VCRs. If your VCR is not Smartlink compatible, a message will be displayed to
remind you to set your VCR timer.
• Once a recording has begun, you can switch the TV to standby mode, but do not
switch off the TV completely or the recording may be cancelled.
• If an age restriction for programmes has been selected, a message asking for a
PIN code will appear on the screen. For more details refer to “Parental Lock”
on page 35.
18 GB
To
Do this
Set a programme to be displayed
automatically on the screen when it starts
– Reminder
1
2
3
4
Press F/f/G/g to select the future programme you want to
display.
Press .
Press F/f to select “Reminder”.
Press
to automatically display the selected programme
when the programme starts.
Set the time and date of a programme you
want to record – Manual timer REC
1
2
3
4
5
Press .
Press F/f to select “Manual timer REC”, then press .
Press F/f to select the date, then press g.
Set the start and stop time in the same way as in step 3.
Press F/f to select the programme, then press
to set the
TV and your VCR timers.
A
symbol appears by that programme’s information. The
indicator on the TV (front) lights up.
Notes
• You can set VCR timer recording on the TV only for Smartlink compatible
VCRs. If your VCR is not Smartlink compatible, a message will be displayed to
remind you to set your VCR timer.
• Once a recording has begun, you can switch the TV to standby mode, but do not
switch off the TV completely or the recording may be cancelled.
• If an age restriction for programmes has been selected, a message asking for a
PIN code will appear on the screen. For more details refer to “Parental Lock”
on page 35.
Cancel a recording/reminder – Timer list
1
2
3
Press .
Press F/f to select “Timer list”.
Press F/f to select the programme you want to cancel, then
press .
4
Press G to select “Yes”, then press
A display appears to confirm that you want to cancel the programme.
to confirm.
Tip
You can also display the Digital Electronic Programme Guide (EPG) by selecting “Digital EPG” in the “MENU” (page 22).
19 GB
Watching TV
A c symbol appears by that programme’s information.
Note
If you switch the TV to standby mode, it will automatically turn itself on
when the programme is about to start.
Using the Digital Favourite list
*
The Favourite feature allows you to select
programmes from a list of up to 20 channels you
specify. To display the Favourite list, see “Navigating
through menus” (page 22).
Digital Favourite list
* This function may not be available in some countries.
To
Do this
Create your Favourite list for the first time
A message appears asking if you want to add channels to the Favourite list
when you select “Digital Favourites” in the “MENU” for the first time.
1
2
Press
to select “Yes”.
Press F/f to select the channel you want to add.
If you know the channel number, you can use the number buttons to
directly select a channel.
3
Press
.
Channels that are stored in the Favourite list are indicated by a
symbol.
Turn off the Favourite list
Press RETURN.
See brief details on current programmes
Press
while selecting a channel. Press again to cancel.
Watch a channel
Press
while selecting a channel.
Add or remove channels in the Favourite
list
1
Press the blue button.
Channels that are stored in the Favourite list are indicated by a
symbol.
2
Press F/f to select the channel you want to add or remove.
If you know the channel number, you can use the number buttons to
directly select a channel.
3
4
Remove all channels from the Favourite list 1
2
Press .
Press the blue button to return to the Favourite list.
Press the blue button.
Press the yellow button.
A display appears to confirm that you want to delete all channels from the
Favourite list.
3
20 GB
Press G to select “Yes”, then press
to confirm.
Additional operations
Viewing pictures from
connected equipment
Switch on the connected equipment, then
perform one of the following operation.
For an auto-tuned VCR (page 7)
In analogue mode, press PROG +/-, or the number
buttons, to select the video channel.
For other connected equipment (page 39)
Press
/
repeatedly until the correct input
symbol (see below) appears on the screen.
AV1/
AV1,
AV2/
AV2,
AV3/
AV3:
Audio/video or RGB input signal through the scart
socket
/
1, 2 or 3.
appears only if an RGB
source has been connected.
AV4:
Component input signal through the Y, PB/CB, PR/CR
sockets
/
4, and audio input signal through the
L (MONO), R sockets
/
4.
AV5:
Digital audio/video input signal through the HDMI IN 5
socket.
Do this
Return to normal TV Press the TV function button,
operation
DIGITAL or ANALOG.
Access the Input
signal index table
(except for PC video
input signal)
Press
to access the Input signal
index table. (Then, only in
analogue mode, press g.) To
select an input source, press F/f,
then press
.
To use the Tools menu
Press TOOLS to display the following options when
viewing pictures from connected equipment other
than a PC.
Options
Description
Close
Closes the Tools menu.
PAP (or Single Picture) See page 17.
Picture Mode
See page 23.
Sound Mode
See page 26.
Power Saving
See page 29.
Sleep Timer
See page 29.
i Volume*
See page 30.
Auto Clock Set
Allows you to switch to digital
mode and obtain the time.
* This option appears only if “i Speaker Link” is set to
“Off” (page 30).
AV6:
Digital audio/video input signal through the HDMI IN 6
socket. Audio input signal is analogue only if the
equipment has been connected using the DVI and audio
out socket.
AV7/
AV7/
AV7:
Input symbols appear depending on the connected
equipment and the “AV7 Input” setting in the “AV Setup” menu (page 31).
AV7: Component input signal through the Y, PB/CB,
7, and audio input signal through the
PR/CR sockets
audio L (MONO)/R sockets
7.
AV7: Composite input signal through the video
socket
7, and audio input signal through the audio L
(MONO)/R sockets
7.
AV7: S video input signal through the S video
socket
7, and audio input signal through the audio
L (MONO)/R sockets
7.
PC:
PC video input signal through the PC
socket, and
audio input signal through the PC audio socket
.
21 GB
Watching TV
For equipment connected to the scart sockets using a
fully-wired 21-pin scart lead (page 40)
Start playback on the connected equipment.
The picture from the connected equipment appears on
the screen.
To
Using MENU Functions
Navigating through
menus
Icon
Description
Digital*
Returns to the last viewed digital
channel.
“MENU” allows you to enjoy various convenient
features of this TV. You can easily select channels or
inputs sources and change the settings for your TV.
Digital EPG*
Displays the Digital Electronic
Programme Guide (EPG).
For details about settings, see page 18.
External Inputs
Selects equipment connected to your TV.
• To watch the desired external input,
select the input source, then press
.
• To assign a label to an external input,
see page 31.
Settings
Displays the Settings menu where most
of the advanced settings and adjustments
are performed.
For details about settings, see page 23 to
36.
2
3
1
1
Press MENU to display the menu.
Icon
Description
Digital Favourites*
Displays the Favourite list. For details
about settings, see page 20.
Analogue
Returns to the last viewed analogue
channel.
22 GB
* This function may not be available in some countries.
2
3
Press F/f to select an option.
Press
to confirm a selected option.
To exit the menu, press MENU.
Picture menu
You can select the options listed below on the Picture
menu.
1
Press F/f to select “Settings” on MENU,
then press .
2
Press F/f to select a menu icon, then
press .
3
Press F/f/G/g to select an option.
For the input currently being viewed, select whether to use the common setting or to
set each item separately.
“Common”: Applies common settings whose adjustments are shared with other
inputs in which “Target Inputs” is set to “Common”.
Current input name (e.g. AV1): Allows you to set each option separately for the
current input.
Picture Mode
Selects the picture mode.
“Vivid”: For enhanced picture contrast and sharpness.
“Standard”: For standard picture. Recommended for home entertainment.
“Custom”: Allows you to store your preferred settings.
Reset
Resets all the “Picture” settings except “Target Inputs” and “Picture Mode” to the
factory settings.
Tip
“Advanced Settings” (page 25) is also not reset. Select “Reset” in “Advanced Settings” to reset
items in “Advanced Settings”.
Backlight
Adjusts the brightness of the backlight.
Contrast
Increases or decreases picture contrast.
Brightness
Brightens or darkens the picture.
Colour
Increases or decreases colour intensity.
Hue
Increases or decreases the green tones and red tones.
Tip
“Hue” can only be adjusted for an NTSC colour signal (e.g. U.S.A. video tapes).
Continued
23 GB
Using MENU Functions
Target Inputs
Colour Temperature
Adjusts the whiteness of the picture.
“Cool”: Gives the white colours a blue tint.
“Neutral”: Gives the white colours a neutral tint.
“Warm 1”/“Warm 2”: Gives the white colours a red tint. “Warm 2” gives a redder
tint than “Warm 1”.
Tip
“Warm 1” and “Warm 2” can only be selected when you set “Picture Mode” to “Custom”.
Sharpness
Sharpens or softens the picture.
Noise Reduction
Reduces the picture noise (snowy picture).
“Auto”: Automatically reduces the picture noise.
“High”/“Medium”/“Low”: Modifies the effect of the noise reduction.
“Off”: Turns off the Noise Reduction feature.
“BNR”: Reduces the block picture noise. This is effective for digital channels, or a
connected DVD player/digital satellite receiver with MPEG playback.
Tips
• “Auto” is not available when watching component, HDMI or digital RF inputs.
• “Noise Reduction” is not available when using Freeze or PAP features.
DRC Mode
Selects a high-resolution picture with 4x density, for high quality sources (e.g. DVD
players, satellite receivers).
“Mode 1”: Recommended for moving pictures.
“Mode 2”: Recommended for still images and text.
“Off”: Turns off the DRC Mode.
Tip
“DRC Mode” is not available when “Game Mode” is set to “On” or when using Freeze or PAP
features; also not available when watching 480p, 576p, 720p, 1080i or 1080p sources.
DRC Palette
Customizes the level of detail (“Reality”) and smoothness (“Clarity”) for each input
signal. For example, you can create one custom setting to optimize your cable input
picture, and create another to optimize your DVD player’s picture.
The DRC palette appears.
1
Press F/f/G/g to adjust the position of the marker (z).
As you move the z higher along the “Reality” axis, the picture becomes more
detailed. As you move the z to the right along the “Clarity” axis, the picture becomes
smoother.
2
To save the settings, press
.
Tip
“DRC Palette” is not available when “Game Mode” is set to “On”, “DRC Mode” is set to “Off”
or when using Freeze or PAP features; also not available when watching 480p, 576p, 720p,
1080i or 1080p sources.
24 GB
Advanced Settings
Customizes the Picture function in more detail. When you set “Picture Mode” to
“Custom”, you can set/change these settings.
“Reset”: Resets all the advanced settings to the factory settings.
“Black Corrector”: Enhances black areas of the picture for stronger contrast.
“Adv. Contrast Enhancer”: Automatically adjusts “Backlight” and “Contrast” to the
most suitable settings judging from the brightness of the screen. This setting is
especially effective for dark images, increasing vibrancy in the picture.
“Gamma”: Adjusts the balance between bright and dark areas of the picture.
“Clear White”: Emphasizes white colours.
“Live Colour”: Makes colours more vivid.
“Colour Space”: Changes the colour reproduction gamut. “Wide” reproduces the
vivid colour and “Normal” reproduces the standard colour.
“White Balance”: Adjusts the colour temperature colour by colour.
“Detail Enhancer”: Enhances the details of the picture.
“Edge Enhancer”: Enhances the outline of the picture.
Tips
25 GB
Using MENU Functions
• “Adv. Contrast Enhancer” and “Detail Enhancer” are not available when using Freeze or
PAP features.
• “Live Colour” is not available when “Colour Space” is set to “Normal”.
Sound menu
You can select the options listed below on the Sound
menu. To select options in “Settings”, refer to “Picture
menu” (page 23).
Target Inputs
For the input currently being viewed, select whether to use the common setting or to
set each item separately.
“Common”: Applies common settings whose adjustments are shared with other
inputs in which “Target Inputs” is set to “Common”.
Current input name (e.g. AV1): Allows you to set each option separately for the
current input.
Sound Mode
Selects the sound mode.
“Dynamic”: Enhances treble and bass.
“Standard”: For standard sound. Recommended for home entertainment.
“Custom”: Flat response. Also allows you to store your preferred settings.
Reset
Resets all the “Sound” settings except “Target Inputs”, “Sound Mode” and “Dual
Sound” to the factory settings.
Treble
Adjusts higher-pitched sounds.
Bass
Adjusts lower-pitched sounds.
Balance
Emphasizes left or right speaker balance.
Auto Volume
Keeps a constant volume level even when volume level gaps occur (e.g. adverts tend
to be louder than programmes).
Volume Offset
Adjusts the volume level of the current input relative to other inputs, when “Target
Inputs” is set to the current input name (e.g. AV1).
Surround
Selects the surround mode.
“Dolby Virtual”: Uses the TV speakers to simulate the surround effect produced by
a multi channel system.
“Off”: For normal stereo or mono reception.
BBE
Gives sound more impact by compensating for phase effects in speakers using the
“BBE High Definition Sound System”.
Dual Sound
Selects the sound from the speaker for a stereo or bilingual broadcast.
“Stereo”, “Mono”: For a stereo broadcast.
“A”/“B”/“Mono”: For a bilingual broadcast, select “A” for sound channel 1, “B” for
sound channel 2, or “Mono” for a mono channel, if available.
Tip
If you select other equipment connected to the TV, set “Dual Sound” to “Stereo”, “A” or “B”.
Tip
Sound menu options other than “Dual Sound” cannot be used for headphones and audio output sockets.
26 GB
Screen menu
You can select the options listed below on the Screen
menu. To select options in “Settings”, refer to “Picture
menu” (page 23).
For the input currently being viewed, select whether to use the common setting or to
set each item separately.
“Common”: Applies common settings whose adjustments are shared with other
inputs in which “Target Inputs” is set to “Common”.
Current input name (e.g. AV1): Allows you to set each option separately for the
current input.
Screen Format
For details about the screen format, see “To change the screen mode manually to suit
the broadcast” (page 16).
Auto Format
Automatically changes the screen format according to the broadcast signal. To keep
your setting, select “Off”.
Tip
Even if “Auto Format” is set to “On” or “Off”, you can always modify the format of the screen
by pressing
repeatedly.
4:3 Default
Selects the default screen mode for use with 4:3 broadcasts.
“Smart”: Displays conventional 4:3 broadcasts with an imitation wide screen effect.
“4:3”: Displays conventional 4:3 broadcasts in the correct proportions.
“Off”: Keeps the current “Screen Format” setting when the channel or input is
changed.
Tip
This option is available only if “Auto Format” is set to “On”.
Display Area
Adjusts the screen area displaying the picture.
“Full Pixel”: Displays the picture for 1080i or 1080p sources in the original size
when parts of the picture are cut off.
“Normal”: Displays the picture in the original size.
“-1”/“-2”: Enlarges the picture to hide the edge of the picture.
Tip
“Full Pixel” is available only when Screen Format is set to “Wide”.
Horizontal Shift
Adjusts the horizontal position of the picture for each screen format.
Tip
This option is not available when “Display Area” is set to “Full Pixel”.
Continued
27 GB
Using MENU Functions
Target Inputs
Vertical Shift
Adjusts the vertical position of the picture when the screen format is set to Smart,
Zoom or 14:9.
Vertical Size
Adjusts the vertical size of the picture when the screen format is set to Smart.
28 GB
Set-up menu
You can select the options listed below on the Set-up
menu. To select options in “Settings”, refer to “Picture
menu” (page 23).
Sets the timer to switch on/off the TV.
Sleep Timer
Sets a period of time after which the TV automatically switches itself into standby
mode.
When the Sleep Timer is activated, the
(Timer) indicator on the TV (front) lights
up in orange.
Tips
• If you switch off the TV and switch it on again, “Sleep Timer” is reset to “Off”.
• “TV will soon turn off by Sleep Timer” appears on the screen one minute before the TV
switches to standby mode.
On Timer
Sets the timer to switch on the TV from standby mode.
“Day”: Selects the day on which you want to activate the On Timer.
“Time”: Sets the time to switch on the TV.
“Duration”: Selects the time period after which the TV automatically switches to
standby mode again.
“Volume Set-up”: Sets the volume for when the timer switches on the TV.
Clock Set
Allows you to adjust the clock manually. When the TV is receiving digital channels,
the clock cannot be adjusted manually since it is set to the time code of the
broadcasted signal.
Auto Start-up
Starts the “first time operation menu” to select the language and country/region, tune
in all available digital and analogue channels, and set the time (only when no digital
channels are received). Usually, you do not need to do this operation because the
language and country/region will have been selected and channels already tuned
when the TV was first installed (page 6, 7). However, this option allows you to
repeat the process (e.g. to retune the TV after moving house, or to search for new
channels that have been launched by broadcasters).
Power Saving
Selects the power saving mode to reduce the power consumption of the TV.
When “Picture Off” is selected, the picture is switched off and the
(Picture Off)
indicator on the TV (front) lights up in green. The sound remains unchanged.
Continued
29 GB
Using MENU Functions
Timer Settings
Film Mode
Provides smoother picture movement when playing DVD or VCR images taken on
film, reducing picture blur and graininess.
“Auto 1”: For a stable picture with minimal noise. Set to “Auto 2” if the screen is
partially degraded.
“Auto 2”: Use this setting for standard use.
“Off”: Turns off the Film mode.
Notes
• Even if “Auto 1” or “Auto 2” is selected, “Film Mode” will be automatically turned off and
a moving image will not be played smoothly if the image contains irregular signals or too
much noise.
• Film Mode is not available when using Freeze or PAP features, or when watching 480p,
576p, 720p or 1080p sources.
i Volume
(headphone volume)
Adjusts the volume of the headphones when “i Speaker Link” is set to “Off”.
i Speaker Link
(headphone speaker
link)
Switches the TV’s internal speakers on/off when headphones are connected.
“On”: Sound is output only from headphones.
“Off”: Sound is output from both the TV and headphones.
Speaker
Switches on/off the TV’s internal speakers.
“On”: The TV speakers are turned on in order to listen to the TV’s sound through the
TV speakers.
“Off”: The TV speakers are turned off in order to listen to the TV’s sound only
through your external audio equipment connected to the audio output sockets.
Audio Out
“Variable”: The audio output from your audio system can be controlled by the TV’s
remote.
“Fixed”: The audio output of the TV is fixed. Use your audio receiver’s volume
control to adjust the volume (and other audio settings) through your audio system.
Light Sensor
“On”: Automatically optimizes the picture settings according to the ambient light in
the room.
“Off”: Turns off the “Light Sensor” feature.
Logo Illumination
Lights up and turns off the Sony logo on the front of the TV.
Language
Selects the language in which the menus are displayed.
Information
Displays your TV’s product information.
All Reset
Resets all settings to the factory settings and then displays the Auto Start-up screen.
Note
All settings, including Digital Favourite list, country, language, auto tuned channels, etc. will
be reset.
30 GB
AV Set-up menu
You can select the options listed below on the AV Setup menu. To select options in “Settings”, refer to
“Picture menu” (page 23).
AV Preset
Equipment labels: Uses one of the preset labels to assign a name to connected
equipment.
“Edit”: Creates your own label. Follow steps 2 to 4 of “Programme Labels” (page 32).
“Skip”: Skips an unnecessary input source.
AV7 Input
“Auto”: Switches automatically between the component video sockets, S Video
socket, and the composite video sockets on the left side of the TV depending on the
cable connection.
“Component”: Activates the component video sockets on the left side of the TV.
“S Video”: Activates the S Video socket on the left side of the TV.
“Composite”: Activates the composite video sockets on the left side of the TV.
Tip
When multiple cables are connected and “Auto” is selected, “Component”, “S
Video”, “Composite” will be activated in that order.
AV2 Output
Sets a signal to be output through the socket labelled
/
2 on the rear of the
TV. If you connect a VCR or other recording equipment to the
/
2 socket,
you can then record from the equipment connected to other sockets of the TV.
“TV”: Outputs a broadcast.
“AV1”: Outputs signals from equipment connected to the
/
1 socket.
“AV3”: Outputs signals from equipment connected to the
/
3 socket.
“AV7”: Outputs signals from equipment connected to the
/
7 socket.
“Auto”: Outputs whatever is being viewed on the screen (except signals from the
/
4, HDMI IN 5, HDMI IN 6 and PC
sockets).
Colour System
Selects the colour system (“Auto”, “PAL”, “SECAM”, “NTSC3.58” or
“NTSC4.43”) according to the input signal from the input source.
Game Mode
Depending on the game software, reaction times may slow during fast-moving
scenes, etc. Select “On” to improve the reaction times.
Colour Matrix
Usually used in the factory setting (AV1/2/3/7 (Composite and S video input signal)
is set to “ITU601”, and AV4/5/6/7 (Component input signal) is set to “Auto”). If the
tone of the picture from the input source is unnatural, select either “ITU601” or
“ITU709”, which normalizes the tone.
31 GB
Using MENU Functions
Assigns a name to any equipment connected to the side and rear sockets. The name
will be displayed briefly on the screen when the equipment is selected. You can skip
an input source that is not connected to any equipment.
1 Press F/f to select the desired input source, then press .
2 Press F/f to select the desired option below, then press .
Analogue Set-up menu
You can select the options listed below on the
Analogue Set-up menu. To select options in
“Settings”, refer to “Picture menu” (page 23).
1 Digit Direct
When “1 Digit Direct” is set to “On”, you can select an analogue channel using one
preset number button (0 - 9) on the remote.
Note
When “1 Digit Direct” is set to “On”, you cannot select channel numbers 10 and above entering
two digits using the remote.
Auto Tuning
Tunes in all the available analogue channels.
Usually you do not need to do this operation because the channels are already tuned
when the TV was first installed (page 7). However, this option allows you to repeat
the process (e.g. to retune the TV after moving house, or to search for new channels
that have been launched by broadcasters).
Programme Sorting
Changes the order in which the analogue channels are stored on the TV.
1 Press F/f to select the channel you want to move to a new position,
then press .
2 Press F/f to select the new position for your channel, then press .
Programme Labels
Assigns a channel name of your choice up to five letters or numbers. The name will
be displayed briefly on the screen when the channel is selected. (Names for channels
are usually taken automatically from Analogue Text (if available).)
1 Press F/f to select the channel you want to name, then press .
2 Press F/f to select the desired letter or number (“_” for a blank space),
then press g.
If you input a wrong character
Press G/g to select the wrong character. Then, press F/f to select the correct
character.
To delete all the characters
.
Repeat the procedure in step 2 until the name is complete.
Select “OK”, then press .
Select “Reset”, then press
3
4
32 GB
Manual Programme
Preset
Before selecting “Label”/“AFT”/“Audio Filter”/“Skip”/“Decoder”, press PROG +/to select the programme number with the channel. You cannot select a programme
number that is set to skip (page 34).
Programme/System/Channel
Presets programme channels manually.
1 Press F/f to select “Programme”, then press .
2 Press F/f to select the programme number you want to manually tune
(if tuning a VCR, select channel 00), then press RETURN.
3 Press F/f to select “System”, then press .
4 Press F/f to select one of the following TV broadcast systems, then
press G.
B/G: For western European countries/regions
I: For the United Kingdom
D/K: For eastern European countries/regions
L: For France
Press F/f to select “Channel”, then press .
Press F/f to select “S” (for cable channels) or “C” (for terrestrial
channels), then press g.
Note
“S” is not available when “United Kingdom” is selected for “Country” (page 6).
7
Tune the channels as follows:
If you do not know the channel number (frequency)
Press F/f to search for the next available channel. When a channel has been found,
the search will stop. To continue searching, press F/f.
If you know the channel number (frequency)
Press the number buttons to enter the channel number of the broadcast you want or
your VCR channel number.
8
9
Press
to jump to “Confirm”, then press
Press f to select “OK”, then press .
.
Repeat the procedure above to preset other channels manually.
Label
Assigns a name of your choice, up to five letters or numbers, to the selected channel.
This name will be displayed briefly on the screen when the channel is selected.
To input characters, follow steps 2 to 4 of “Programme Labels” (page 32).
AFT
Allows you to fine-tune the selected programme number manually if you feel that a
slight tuning adjustment will improve the picture quality.
You can adjust the fine tuning over a range of -15 to +15. When “On” is selected, the
fine tuning is performed automatically.
Audio Filter
Improves the sound for individual channels in the case of distortion in mono
broadcasts. Sometimes a non-standard broadcast signal can cause sound distortion or
intermittent sound muting when watching mono programmes.
If you do not experience any sound distortion, we recommend that you leave this
option set to the factory setting “Off”.
Notes
• You cannot receive stereo or dual sound when “Low” or “High” is selected.
• “Audio Filter” is not available when “System” is set to “L”.
Continued
33 GB
Using MENU Functions
5
6
Skip
Skips unused analogue channels when you press PROG +/- to select channels. (You
can still select a skipped channel using the number buttons.)
Decoder
Views and records the scrambled channel selected when using a decoder connected
directly to scart connector
/
1, or to scart connector
/
2 via a VCR.
Note
This option is not available when “United Kingdom” is selected for “Country” (page 6).
Confirm
Saves changes made to the “Manual Programme Preset” settings.
34 GB
Digital Set-up menu
You can select the options listed below on the Digital
Set-up menu. To select options in “Settings”, refer to
“Picture menu” (page 23).
Note
Some functions may not be available in some countries.
Displays the “Digital Settings” menu.
Subtitle Setting
Displays digital subtitles on the screen.
When “For Hard Of Hearing” is selected, some visual aids may also be displayed
with the subtitles (if TV channels broadcast such information).
Subtitle Language
Selects which language subtitles are displayed in.
Audio Language
Selects the language used for a programme. Some digital channels may broadcast
several audio languages for a programme.
Audio Type
Increases the sound level when “For Hard Of Hearing” is selected.
Parental Lock
Sets an age restriction for programmes. Any programme that exceeds the age
restriction can only be watched after a PIN Code is entered correctly.
1 Press the number buttons to enter your existing PIN code.
If you have not previously set a PIN, a PIN code entry screen appears. Follow the
instructions of “PIN Code” below.
2
3
Press F/f to select the age restriction or “None” (for unrestricted
watching), then press .
Press RETURN.
PIN Code
Sets a PIN code for the first time, or allows you to change your PIN code.
1 Enter a PIN as follows:
If you have previously set a PIN
Press the number buttons to enter your existing PIN.
If you have not set a PIN
Press the number buttons to enter the factory setting PIN of 9999.
2
Press the number buttons to enter the new PIN code.
A message appears to inform you that the new PIN has been accepted.
3
Press RETURN.
Tip
PIN code 9999 is always accepted.
Continued
35 GB
Using MENU Functions
Digital Settings
Technical Set-up
Displays the Technical Set-up menu.
“Auto Service Update”: Enables the TV to detect and store new digital services as
they become available.
“Software Download”: Enables the TV to automatically receive software updates
free through your existing aerial (when issued). It is recommended that this option
be set to “On” at all times. If you do not want your software to be updated, set this
option to “Off”.
“System Information”: Displays the current software version and the signal level.
“Time Zone”: Allows you to manually select the time zone you are in, if it is not the
same as the default time zone setting for your country.
CA Module Set-up
Allows you to access a Pay Per View service once you obtain a Conditional Access
Module (CAM) and a view card. See page 39 for the location of the
(PCMCIA)
socket.
Notes
• CAM is not supported in all countries. Check with your authorized dealer.
• “CA Module Set-up” is available only when a CAM is inserted.
Digital Tuning
Displays the “Digital Tuning” menu.
Digital Auto Tuning
Tunes in all the available digital channels.
Usually you do not need to do this operation because the channels were already tuned
when the TV was first installed (page 7). However, this option allows you to repeat
the process (e.g. to retune the TV after moving house, or to search for new channels
that have been launched by broadcasters).
Programme List Edit
Removes any unwanted digital channels stored on the TV, and changes the order of
the digital channels stored on the TV.
1 Press F/f to select the channel you want to remove or move to a new
position.
If you know the programme number
Press the number buttons to enter the three-digit programme number of the broadcast
you want.
2
Remove or change the order of the digital channels as follows:
To remove the digital channel
Press
. A message that confirms whether the selected digital channel is to be
.
deleted appears. Press G to select “Yes”, then press
To change the order of the digital channels
Press g, then press F/f to select the new position for the channel and press G.
Repeat the procedure in steps 1 and 2 to move other channels if required.
3
Press RETURN.
Digital Manual Tuning
Tunes the digital channels manually.
1 Press the number button to select the channel number you want to
manually tune, then press F/f to tune the channel.
2 When the available channels are found, press F/f to select the channel
you want to store, then press .
3 Press F/f to select the programme number where you want to store the
new channel, then press .
Repeat the above procedure to manually tune other channels.
36 GB
PC Settings menu
You can select the options listed below on the PC
Settings menu when the TV is connected to a PC.
1
Press
/ repeatedly until
appears on the screen.
2
Press MENU to display the PC settings
menu.
PC
Picture
Selects the display mode.
“Video”: Select to view video images.
“Text”: Select to view text, charts or tables.
Reset
Resets all the “Picture” settings except “Display Mode” to the factory settings.
Backlight
Adjusts the brightness of the backlight.
Contrast
Increases or decreases picture contrast.
Brightness
Brightens or darkens the picture.
Colour Temperature
Adjusts the whiteness of the picture.
“Cool”: Gives the white colours a blue tint.
“Neutral”: Gives the white colours a neutral tint.
“Warm 1”/“Warm 2”: Gives the white colours a red tint. “Warm 2” gives a redder
tint than “Warm 1”.
Sound
Sound Mode
Selects the sound mode.
“Dynamic”: Enhances treble and bass.
“Standard”: For standard sound. Recommended for home entertainment.
“Custom”: Flat response. Also allows you to store your preferred settings.
Continued
37 GB
Using MENU Functions
Display Mode
Others
Auto Adjustment
Automatically adjusts the display position, phase and pitch of the picture when the
TV receives an input signal from a connected PC.
Tip
Auto Adjustment may not work well with some input signals. In such cases, manually adjust
“Phase”, “Pitch”, “Horizontal Shift” and “Vertical Shift”.
Reset
Resets all the “Others” settings to the factory settings.
Phase
Adjusts the phase when the screen flickers.
Pitch
Adjusts the pitch when the picture has unwanted vertical stripes.
Horizontal Shift
Adjusts the horizontal position of the picture for each screen format.
Vertical Shift
Adjusts the vertical position of the picture for each screen format.
Screen Format
Selects the screen mode.
“Normal”: Displays the picture in its original size.
“Full1”: Enlarges the picture to fill the display area, keeping its original horizontalto-vertical aspect ratio.
“Full2”: Enlarges the picture to fill the display area.
Power Management
Switches the TV to standby mode if no signal is received for 30 seconds.
38 GB
Using Optional Equipment
Connecting optional equipment
You can connect a wide range of optional equipment to your TV. Connecting cables are not supplied.
Connecting to the TV (side)
To connect
Do this
DVD player with
component output
A
Connect to the component Y, PB/
7 and
CB, PR/CR sockets
audio L (MONO), R sockets
7.
S VHS/Hi8/DVC
camcorder B
Connect to the S video socket
7 or the video socket
7,
and the audio sockets
7. To
avoid picture noise, do not connect
the camcorder to the video socket
7 and the S video socket
7 at the same time. If you
connect mono equipment, connect
to the L socket
7.
Tip
Headphones C
DVD player
with component
output
S VHS/Hi8/DVC
camcorder
Headphones
For service use only
Connect to the i socket to listen to
sound from the TV on headphones.
Conditional Access To use Pay Per View services. For
Module (CAM) D details, refer to the instruction
manual supplied with your CAM.
To use the CAM, press the eject
button and remove the “dummy”
card. Switch off the TV when
inserting your CAM into the CAM
slot. When you do not use the
CAM, we recommend that the
“dummy” card be inserted and
kept in the CAM slot.
Note
CAM is not supported in all
countries. Check with your
authorized dealer.
Continued
39 GB
Using Optional Equipment
You can select the input signal by
setting “AV7 Input” in the “AV Setup” menu (page 31).
Connecting to the TV (rear)
IN
To connect
Do this
Digital satellite
receiver or DVD
player E
Connect to the HDMI IN 5 or 6
socket if the equipment has a
HDMI socket. The digital video
and audio signals are input from
the equipment. If the equipment
has a DVI socket, connect the DVI
socket to the HDMI IN 6 socket
through a DVI - HDMI adaptor
interface (not supplied), and
connect the equipment’s audio out
sockets to the audio in the HDMI
IN 6 sockets.
Note
5
IN
6
Digital satellite
receiver
L
R
DVD player
The HDMI sockets only support the
following video inputs: 480i, 480p,
576i, 576p, 720p, 1080i and 1080p.
To connect a PC, use the PC
socket.
PC
OPTICAL OUT
PC F
Connect to the PC
sockets. It
is recommended to use a PC cable
with ferrites.
Digital audio
(PCM) component
G
Connect to the OPTICAL OUT
socket using the Optical audio
cable.
Note
Digital audio (PCM)
component
L
R
DVD player with
component output
Video game
equipment
DVD player
Decoder
VCR
DVD player
DVD recorder
VCR
Decoder
40 GB
The OPTICAL OUT socket only
supports digital terrestrial signals.
Hi-Fi audio
equipment
PC
Hi-Fi audio
equipment H
Connect to the audio output
sockets
to listen to the sound
from the TV on Hi-Fi audio
equipment.
DVD player with
component output
I
Connect to the component sockets
and the audio sockets
/
4.
Video game
equipment, DVD
player or decoder
J
Connect to the scart socket
/
1. When you connect the
decoder, the scrambled signal from
the TV tuner is output to the
decoder, then the unscrambled
signal is output from the decoder.
DVD recorder or
VCR that supports
SmartLink K
Connect to the scart socket
/
2. SmartLink is a direct link
between the TV and a VCR/DVD
recorder.
VCR or DVD
player L
For details, see page 5.
4
Programming the
remote
Switch on your equipment and check that
the following main functions work.
H (playback), x (stop), m (rewind), M (fast
forward), channel selection for both VCR and
DVDs, TOP MENU/MENU and F/f/G/g only
for DVDs.
If your equipment is not working, or some of the
functions do not work
Enter the correct code or try the next code listed
for the brand. However, not all models of every
brand may be covered.
To return to normal TV operation
Press the TV function button, DIGITAL or
ANALOG.
This remote is preset to operate Sony TVs, most Sony
DVDs, VCRs and AMPs (Home Theatre, etc.).
To control VCRs and DVDs of other manufacturers
(and some other Sony VCR, DVD and AMP models),
do the following procedure to programme the remote.
Note
Before you start, look up the three-digit code for your brand
of DVD, VCR or AMP from the “Manufacturer’s codes” on
page 41.
Manufacturer’s codes
VCR brand list
1
2
Code
SONY
301, 302, 303, 304, 305, 306, 307, 308,
309, 310, 362
AIWA
325, 331, 351
AKAI
326, 329, 330
DAEWOO
342, 343
GRUNDIG
358, 355, 360, 361, 320, 351, 366
HITACHI
327, 333, 334
JVC
314, 315, 322, 344, 352, 353, 354, 348,
349
LG
332, 338
LOEWE
358, 355, 360, 361, 320, 351
MATSUI
356, 357
ORION
328
PANASONIC
321, 323
PHILIPS
311, 312, 313, 316, 317, 318, 358, 359,
363, 364
SAMSUNG
339, 340, 341, 345
SANYO
335, 336
SHARP
324
THOMSON
319, 350, 365
TOSHIBA
337
3
1
Press and hold the DVD, VCR or AMP
function button you want to programme on
the remote, then press
, keeping the
function button pressed down.
The selected function button (DVD, VCR or
AMP) will flash.
2
3
Press the number buttons to enter the
three-digit manufacturer’s code number
while the button is lit. If code is not entered
within 10 seconds, you must perform the
step 1 again.
Press
.
When the programming is correct, the selected
function button will flash twice, and when not, it
will flash five times.
Continued
41 GB
Using Optional Equipment
1
Brand
DVD brand list
DVD Player
AV receiver
Brand
Code
SONY
001, 029, 030, 036, 037, 038, 039, 040,
041, 042, 043, 044, 053, 054, 055
AIWA
021
AKAI
032
DENON
018, 027, 020, 002
GRUNDIG
009, 028, 023, 024, 016, 003
HITACHI
025, 026, 015, 004, 035
JVC
006, 017
KENWOOD
008
LG
015, 014, 034
LOEWE
009, 028, 023, 024, 016, 003
MATSUI
013, 016
ONKYO
022, 033
PANASONIC
018, 027, 020, 002, 045, 046, 047
PHILIPS
009, 028, 023, 024, 016, 003, 031
PIONEER
004, 050, 051, 052
SAMSUNG
011, 014
SANYO
007
SHARP
019, 027
THOMSON
012
TOSHIBA
003, 048, 049
YAMAHA
018, 027, 020, 002
DVD/VCR Player
Brand
Code
SONY
101
DVD recorder
Brand
Code
SONY
201, 202, 203
AUX Sony systems brand list
DAV Home Theatre System
Brand
Code
SONY (DAV)
401, 402, 403, 404
42 GB
Brand
Code
SONY
451, 452, 453, 454
Digital terrestrial receiver
Brand
Code
SONY
501, 502, 503
Additional Information
Specifications
Display Unit
Power Requirements:
220–240 V AC, 50 Hz
Screen Size:
46 inches (Approx. 116.8 cm measured diagonally)
Display Resolution:
1,920 dots (horizontal) × 1,080 lines (vertical)
Power Consumption:
249 W
Standby Power Consumption:
0.3 W
Dimensions (w × h × d):
Approx. 1,262 × 795 × 322 mm (with stand)
Approx. 1,262 × 734 × 121 mm (without stand)
Mass:
Approx. 41 kg (with stand)
Approx. 36 kg (without stand)
Panel System
LCD (Liquid Crystal Display) Panel
TV System
Analogue:
Digital:
Depending on your country/region selection:
B/G/H, D/K, L, I
DVB-T
Colour/Video System
Analogue:
Digital:
PAL, SECAM
NTSC 3.58, 4.43 (only Video In)
MPEG-2 MP@ML
75 ohm external terminal for VHF/UHF
Channel Coverage
Analogue:
Digital:
VHF:
E2–E12
UHF:
E21–E69
CATV: S1–S20
HYPER: S21–S41
D/K:
R1–R12, R21–R69
L:
F2–F10, B–Q, F21–F69
I:
UHF B21–B69
VHF/UHF
Terminals
/
1
21-pin scart connector (CENELEC standard) including
audio/video input, RGB input, and TV audio/video
output.
/
2 (SmartLink)
21-pin scart connector (CENELEC standard) including
audio/video input, RGB input, selectable audio/video
output, and SmartLink interface.
Sound Output
11 W + 11 W
Supplied Accessories
Refer to “1: Checking the accessories” on page 4.
Optional Accessories
• Wall-Mount Bracket SU-WL51
• TV stand SU-FL61
• Colour Variation Unit CRU-46X1
Design and specifications are subject to change
without notice.
Continued
43 GB
Additional Information
Aerial
/
3
21-pin scart connector (CENELEC standard) including
audio/video input, RGB input, and audio/video output
which currently appears on the screen.
4
Supported formats: 1080i, 720p, 576p, 576i, 480p, 480i
Y: 1 Vp-p, 75 ohms, 0.3V negative sync
PB/CB: 0.7 Vp-p, 75 ohms
PR/CR: 0.7 Vp-p, 75 ohms
4
Audio input (phono jacks)
500 mVrms
Impedance: 47 kilo ohms
HDMI IN 5, 6
Video: 1080p, 1080i, 720p, 576p, 576i, 480p, 480i
Audio: Two channel linear PCM
32, 44.1 and 48 kHz, 16, 20 and 24 bits, or
analogue audio input (phono jacks)
(HDMI IN 6)
7
Supported formats: 1080i, 720p, 576p, 576i, 480p, 480i
Y: 1 Vp-p, 75 ohms, 0.3V negative sync
PB/CB: 0.7 Vp-p, 75 ohms
PR/CR: 0.7 Vp-p, 75 ohms
7 S video input (4-pin mini DIN)
7 Video input (phono jack)
7 Audio input (phono jacks)
OPTICAL OUT (OPTICAL OUT jack)
Audio output (Left/Right) (phono jacks)
PC
PC Input (15 Dsub) (see page 44)
G: 0.7 Vp-p, 75 ohms, non Sync on Green
B: 0.7 Vp-p, 75 ohms, non Sync on Green
R: 0.7 Vp-p, 75 ohms, non Sync on Green
HD: 1-5 Vp-p
VD: 1-5 Vp-p
PC audio input (minijack)
i Headphones jack
CAM (Conditional Access Module) slot
PC Input Signal Reference Chart
Signals
VGA
SVGA
XGA
WXGA
Horizontal (Pixel)
Vertical (Line)
Horizontal
frequency
(kHz)
Vertical
Standard
frequency (Hz)
640
480
31.5
60
VGA
640
480
37.5
75
VESA
720
400
31.5
70
VGA-T
800
600
37.9
60
VESA Guidelines
800
600
46.9
75
VESA
1024
768
48.4
60
VESA Guidelines
1024
768
56.5
70
VESA
1024
768
60
75
VESA
1280
768
47.4
60
VESA
1280
768
47.8
60
VESA
1360
768
47.7
60
VESA
• This TV’s PC input does not support Sync on Green or Composite Sync.
• This TV’s PC input does not support interlaced signals.
• For the best picture quality, it is recommended to use the signals (boldfaced) in the above chart with a 60 Hz vertical frequency
from a personal computer. In plug and play, signals with a 60 Hz vertical frequency will be selected automatically.
44 GB
Troubleshooting
Check whether the 1 (standby) indicator is flashing in red.
When it is flashing
The self-diagnosis function is activated.
1 Count how many 1 (standby) indicator flashes between each two second break.
For example, the indicator flashes three times, then there is a two second break, followed by another three flashes, etc.
2
Press 1 on the TV (right side) to switch it off, disconnect the mains lead, and inform your dealer or
Sony service centre of how the indicator flashes (number of flashes).
When it is not flashing
1 Check the items in the tables below.
2 If the problem still persists, have your TV serviced by qualified service personnel.
Picture
Cause/Remedy
No picture (screen is dark) and
no sound
• Check the aerial connection.
• Connect the TV to the mains, and press 1 on the TV (right side).
• If the 1 (standby) indicator lights up in red, press TV "/1.
No picture or no menu
information from equipment
connected to the scart
connector
• Check that the optional equipment is on and press
/
repeatedly until
the correct input symbol is displayed on the screen.
• Check the connection between the optional equipment and the TV.
Double images or ghosting
• Check aerial/cable connections.
• Check the aerial location and direction.
Only snow and noise appear
on the screen
• Check if the aerial is broken or bent.
• Check if the aerial has reached the end of its serviceable life (three to five
years in normal use, one to two years at the seaside).
Distorted picture (dotted lines
or stripes)
• Keep the TV away from electrical noise sources such as cars, motorcycles,
hair-dryers or optical equipment.
• When installing optional equipment, leave some space between the optional
equipment and the TV.
• Make sure that the aerial is connected using the supplied coaxial cable.
• Keep the aerial cable away from other connecting cables.
Picture noise when viewing a
TV channel
• Select “Manual Programme Preset” in the “Analogue Set-up” menu and
adjust “AFT” (Automatic Fine Tuning) to obtain better picture reception
(page 33).
Some tiny black points and/or
bright points appear on the
screen
• The picture of a display unit is composed of pixels. Tiny black points and/or
bright points (pixels) on the screen do not indicate a malfunction.
No colour on programmes
• Select “Reset” in the “Picture” menu to return to the factory settings
(page 23).
No colour or irregular colour
when viewing a signal from the
Y, PB/CB, PR/CR sockets
4
or 7
• Check the connection of the Y, PB/CB, PR/CR sockets
4 or 7.
• Make sure that the Y, PB/CB, PR/CR sockets
4 or 7 are firmly seated in
their respective sockets.
Continued
45 GB
Additional Information
Problem
Sound
Problem
Cause/Remedy
No sound, but good picture
• Press 2 +/– or % (Mute).
• Check that “Speaker” is set to “On” in the “Set-up” menu (page 30).
Noisy sound
• See “Picture noise” causes/remedies on page 45.
Channels
Problem
Cause/Remedy
The desired channel cannot be
selected
• Switch between digital and analogue mode and select the desired digital/
analogue channel.
Some channels are blank
• Scrambled/Subscription only channel. Subscribe to the Pay Per View
service.
• Channel is used only for data (no picture or sound).
• Contact the broadcaster for transmission details.
Digital channels are not
displayed
• Contact a local installer to find out if digital transmissions are provided in
your area.
• Upgrade to a higher gain aerial.
General
Problem
Cause/Remedy
The TV turns off automatically
(the TV enters standby mode)
• Check if the “Sleep Timer” is activated, or confirm the “Duration” setting of
“On Timer” (page 29).
• If no signal is received and no operation is performed in the TV mode for
10 minutes, the TV automatically switches to standby mode.
The TV turns on automatically
• Check if the “On Timer” is activated (page 29).
Some input sources cannot be
selected
• Select “AV Preset” in the “AV Set-up” menu and cancel “Skip” of the input
source (page 31).
The remote does not function
• Check that the remote is set correctly for the equipment you are using.
• Check whether the equipment you want to use corresponds to the function
button being pressed (page 13).
• If the remote does not operate the equipment even when the remote has been
set correctly to the equipment, enter the necessary code as explained in
“Programming the remote” (page 41).
• Replace the batteries.
46 GB
Index
Numerics
1 Digit Direct 32
14:9 16
4:3 Default 27
4:3 16
A
Advanced Settings 25
Aerial, connecting 5
AFT 33
All Reset 30
Analogue Set-up menu 32
Analogue Text 16
Audio Filter 33
Audio Language 35
Audio Out 30
Audio Type 35
Auto Adjustment 38
Auto Clock Set 17, 21
Auto Format 27
Auto Start-up 29
Auto Tuning
analogue and digital channels 7
analogue channels only 32
digital channels only 36
Auto Volume 26
AV Preset 31
AV Set-up menu 31
AV2 Output 31
AV7 Input 31
B
C
CA Module Set-up 36
Category list 18
Channels
auto-tuning 7
selecting 15
Skip 34
Clear White 25
Clock Set 29
Colour 23
Colour Matrix 31
Colour System 31
Colour Temperature 24, 37
Confirm 34
Connecting
an aerial/VCR 5
optional equipment 39
D
Digital Auto Tuning 36
Digital Manual Tuning 36
Digital Set-up 35
Digital Set-up menu 35
Digital Text 16
Digital Tuning 36
Display Area 27
Display Mode 37
DRC Mode 24
DRC Palette 24
Dual Sound 26
E
EPG (Digital Electronic Programme
Guide) 18
Equipment labels 31
F
Fastext 16
Favourite list 20
Film mode 30
G
Game Mode 31
Gamma 25
H
Headphones
connecting 39
Speaker Link 30
Volume 30
Horizontal Shift 27, 38
Hue 23
I
Information 30
Input signal index table 21
Interactive service 15
L
Label 33
Language 6, 30
Light Sensor 30
Live Colour 25
Logo Illumination 30
M
P
PAP 17
Parental Lock 35
PC Settings menu 37
Phase 38
Picture Freeze 16
Picture menu 23
Picture Mode 23
Picture Off (
) indicator 14
PIN Code 35
Pitch 38
Power (") indicator 14
Power (1) switch 14
Power Management 38
Power Saving 29
Programme index table 15
Programme Labels 32
Programme List Edit 36
Programme Sorting 32
R
Reminder 19
Remote control
inserting batteries 4
overview 12
programming 41
sensor 14
Reset
PC settings 38
picture 23, 37
sound 26
S
Screen Format 27, 38
Screen menu 27
Screen mode 16
Set-up menu 29
Sharpness 24
Skip 31, 34
Sleep Timer 29
Smart 16
Sound menu 26
Sound Mode 26, 37
Speaker 30
Specifications 43
Standby (1) indicator 14
Subtitle Language 35
Subtitle Setting 35
Surround 26
Additional Information
Backlight 23, 37
Balance 26
Bass 26
Batteries, inserting into the remote 4
BBE 26
Black Corrector 25
Brightness 23, 37
Contrast Enhancer 25
Contrast 23, 37
Country 6
Manual Programme Preset 33
Manual timer REC 19
MENU 22
N
Noise Reduction 24
O
On Timer 29
Continued
47 GB
T
Target Inputs
picture 23
screen 27
sound 26
Technical Set-up 36
Timer ( ) indicator 14
Timer list 19
Timer REC 18
Timer Settings 29
Tools 17, 21
Treble 26
V
VCR
connecting 5
recording 18
Vertical Shift 28, 38
Vertical Size 28
Volume Offset 26
W
Wide 16
Z
Zoom 16
48 GB
Additional Information
49 GB
50 GB
Additional Information
51 GB
KDL-46X2000
Printed on 100% recycled paper using
VOC (Volatile Organic Compound)free vegetable oil based ink.
Printed in Japan
2678257120
2-678-257-12(3)
Download PDF