Samsung DVD-HR720 Instruction manual

Add to my manuals
131 Pages

advertisement

Samsung DVD-HR720 Instruction manual | Manualzz
1-00819S-XSA_01-17
6/9/05
1:45 PM
Page 1
Instruction Manual
DVD-HR720
www.samsung.com
AK68-00819S-01
1-00819S-XSA_01-17
6/9/05
1:45 PM
Page 2
IMPORTANT NOTE
Getting Started
Warning
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE THE COVER(OR BACK).
NO USER-SERVICEABLE PARTS ARE INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
The mains lead on this equipment is supplied with a
moulded plug incorporating a fuse. The value of the
fuse is indicated on the pin face of the plug. If it requires
replacing, a fuse approved to BS1362 of the same
rating must be used.
Never use the plug with the fuse cover omitted if the cover
is detachable. If a replacement fuse cover is
required, it must be of the same colour as the pin face of
the plug. Replacement covers are available from your
dealer.
If the fitted plug is not suitable for the power points in your
house or the cable is not long enough to reach a
power point, you should obtain a suitable safety approved
extension lead or consult your dealer for assistance.
This symbol indicates “dangerous voltage”
inside the product that presents a risk of
electric shock or personal injury.
This symbol indicates important instructions
accompanying the product.
Do not install this equipment in a confined space such
as a bookcase or similar unit.
WARNING : To prevent damage which may result in fire
or electric shock hazard, do not expose this
appliance to rain or moisture.
CAUTION : HDD & DVD RECORDER USES AN INVISIBLE
LASER BEAM WHICH CAN CAUSE
HAZARDOUS RADIATION EXPOSURE IF
DIRECTED. BE SURE TO OPERATE
RECORDER CORRECTLY AS INSTRUCTED.
CAUTION
THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY RESULT
IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR
YOURSELF. REFER SERVICING TO QUALIFIED
PERSONNEL.
2 - English
However, if there is no alternative to cutting off the plug,
remove the fuse and then safely dispose of the
plug. Do not connect the plug to a mains jack, as there is
a risk of shock hazard from the bared flexible cord.
The product unit accompanying this user manual is
licenced under certain intellectual property rights of certain
third parties. This licence is limited to private noncommercial use by end-user consumers for licenced
contents.
No rights are granted for commercial use.
The licence does not cover any product unit other than this
product unit and the licence does not extend to any
unlicenced product unit or process conforming to ISO/IEC
11172-3 or ISO/IEC 13818-3 used or sold in combination
with this product unit. The licence only covers the use of
this product unit to encode and/or decode audio files
conforming to the ISO/IEC 11172-3 or ISO/IEC 13818-3.
No rights are granted under this licence for product
features or functions that do not conform to the ISO/IEC
11172-3 or ISO/IEC 13818-3.
1-00819S-XSA_01-17
6/9/05
1:45 PM
Page 3
Handling Cautions
Precaution
Read these operating instructions carefully before using
the unit. Follow all the safety instructions listed below.
Keep these operating instructions handy for future
reference.
1)
2)
3)
4)
5)
6)
7)
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings, Install in
accordance with the manufacturer's instructions.
8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or
grounding- type plug. A polarized plug has two
blades with one wider than the other. A groundingtype plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. if the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, the point where they exit from the
apparatus.
11) Only use attachments/accessories specified by the
manufacturer.
12) Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid
injury from tip-over.
13) Unplug this apparatus during lightning storms or
when unused for long periods of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
Maintenance of Cabinet
For safety reasons, be sure to disconnect the AC
power cord from the AC outlet.
• Do not use benzene, thinner, or other solvents
for cleaning.
• Wipe the cabinet with a soft cloth.
HDD (Hard Disk Drive)
The hard disk has a high storage density, which
enables long recording durations and quick
access to written data. However, it can easily be
damaged by shock, vibration or dust and should
be kept away from magnets. To avioid losing
important data, observe the following precautions.
• Do not use the HDD & DVD RECORDER in a
place subject to extreame changes in
temperature.
• Do not apply a strong shock to the HDD & DVD
RECORDER.
• Do not place the HDD & DVD RECORDER in a
location subject to mechanical vibrations or in an
unstable location.
• Do not place the HDD & DVD RECORDER on
top of a heat source.
English - 3
Getting Started
Important Safety Instructions
• Before connecting other components to this
recorder, be sure to turn them all off.
• Do not move the recorder while a disc is being
played, or the disc may be scratched or broken, the
recorder’s internal parts may be damaged.
• Do not put a flower vase filled with water or any
small metal objects on the recorder.
• Be careful not to put your hand into the disc tray.
• Do not place anything other than the disc in the
disc tray.
• Exterior interference such as lightning and static
electricity can affect normal operation of this
recorder. If this occurs, turn the recorder off and on
again with the DVD STANDBY/ON button, or
disconnect and then reconnect the AC power cord
to the AC power outlet. The recorder will operate
normally.
• Be sure to remove the disc and turn off the
recorder after use.
• Disconnect the AC power cord from the AC outlet
when you don’t intend to use the recorder for long
periods of time.
• Clean the disc by wiping in a straight line from the
inside to the outside of the disc.
1-00819S-XSA_01-17
6/9/05
1:45 PM
Page 4
Getting Started
• Do not disconnect the AC power cord while the
power is on.
• Do not attempt to change the hard disk. This
may result in a malfunction.
• Do not use scratch-proof protectors or covers.
• Do not use discs printed with label printers
available on the market.
• Do not load warped or cracked discs.
Should the hard disk be damaged, you cannot
recover lost data. The hard disk is only a
temporary storage space.
Disc Storage
Disc Handling
• Use discs with regular
shapes. If an irregular disc
(a disc with a special shape)
is used, this HDD & DVD
RECORDER may be
damaged.
Holding discs
Be careful not to harm the disc because the data on
these discs is highly vulnerable to the environment.
• Do not keep under direct sunlight.
• Keep in a cool ventilated area.
• Store vertically.
• Keep in a clean protection jacket.
• If you move your HDD & DVD RECORDER suddenly
from a cold place to a warm place, condensation may
generate on the operating parts and lens and cause
abnormal disc playback. If this occurs, remove the
disc and wait for one to two hours with the power on
before atttempting playback.
• Be careful not to harm the disc because the data on
these discs is highly vulnerable to the environment.
• Avoid touching the surface of a
disc where recording is
performed.
Disc Specifications
DVD-RAM, DVD-RW and DVD-R
• Clean with an optional DVD-RAM/PD
disc cleaner (LF-K200DCA1 where
available). Do not use cleaners or
cloths for CDs to clean DVD-RAM/
-RW/-R discs.
DVD-Video, Audio-CD
• Wipe off dirt or contamination on the disc with a
soft cloth.
Cautions on handling discs
• Do not write on the printed side with a ball-point
pen or pencil.
• Do not use record cleaning sprays or antistatic.
Also, do not use volatile chemicals, such as
benzene or thinner.
• Do not apply labels or stickers to discs. (Do not
use discs fixed with exposed tape adhesive or
leftover peeled-off stickers.)
4 - English
Disc Type
DVD-Video
• A digital versatile disc (DVD) can contain up to 135minutes of images, 8 audio languages and 32 subtitle
languages. It is equipped with MPEG-2 picture
compression and Dolby digital surrounding, allowing
you to enjoy vivid and clear theatre quality images in
the comfort of your own home.
• When switching from the first layer to the second layer
of a dual-layered DVD Video disc, there may be
momentary distortion in the image and sound. This is
not a malfunction of the unit.
• Once a DVD-RW/-R recorded in Video Mode is
finalised, it becomes DVD-Video.
1-00819S-XSA_01-17
6/9/05
1:45 PM
Page 5
Audio CD
• Recording and playback can be performed on DVDRW discs in both the Video and VR Modes.
• Once a DVD-RW recorded in both the Video and VR
Modes is finalised, you cannot perform addtional
recording.
• Once a DVD-RW recorded in Video Mode is finalised,
it becomes DVD-Video.
CD-RW/-R
• Use a 700MB(80 minutes) CD-R/RW disc. If possible,
do not use a 800MB(90 minutes) or above disc, as the
disc may not play back.
• If the CD-R/RW disc was not recorded as a closed
session, you may experience a delay in the early
playback time, all recorded files may not play.
• Some CD-R/RW discs may not be playable with this
unit, depending on the device which was used to burn
them. For contents recorded on CD-R/RW media from
CDs for your personal use, playability may vary
depending on contents and discs.
DVD-R Disc Playback and Recording
• Once a DVD-R recorded in Video Mode is finalised, it
becomes DVD-Video.
• You can record onto the available space on the disc
and perform editing functions such as giving titles to
discs and programmes and erasing programmes
before finalising.
• When programming is erased from a DVD-R, that
space does not become available. Once an area on a
DVD-R is recorded on, that area is no longer available
for recording, whether the recording is erased or not.
• It takes about 30 seconds for the unit to complete
recording management information after recording
finishes.
• This product optimizes the DVD-R for each recording.
Optimizing is carried out when you start recording
after inserting the disc or turning on the unit.
Recording onto the disc may become impossible if
optimizing is carried out too many times.
• Playback may be impossible in some cases due to the
condition of recording.
• This unit can play back DVD-R discs recorded and
finalised with a Samsung DVD video recorder. It may
not be able to play some DVD-R discs depending on
the disc and the condition of the recording.
• In both modes, playback can be performed before and
after finalisation, but additional recording, deleting and
editing can not be performed after finalisation.
• If you want to record the disc in VR Mode and then
record in V Mode, be sure to execute Format. Be
careful when executing Format because all the
recorded data may be lost.
• A DVD-RW blank disc is initialized to VR Mode when
first initialized.
DVD-RAM Disc Playback and Recording
• Ensure that the recording mode is set to VR mode.
Otherwise, this product will not be able to play the
recording.
• You cannot play a DVD-RAM in most DVD
components due to compatibility issues.
• Only DVD-RAM standard Version 2.0. discs can be
played in this unit.
• DVD-RAM recorded on this unit may not work with
other DVD components. To determine compatibility
with these DVD-RAM discs, refer to the user’s manual
for the player.
• For cartridge type DVD-RAM discs, remove the
cartridge and use the disc only.
Disc Copy
Contents Copy Specifications
Contents
Recorded Video Title
Copy Protected Title
Copy Once Title
MP3
JPEG(photo)
DivX
HDD ➞ DVD
Supported
Not supported
Move
(Deletes the Title in the
HDD after copying)
Not supported
Not supported
Not supported
DVD ➞ HDD
Supported
Not supported
Not supported
supported
supported
Not supported
Once "Copy Once programme" has been recorded on the
DVD disc, this title cannot be copied to HDD anymore.
But "Copy Once programme" has been recorded on the
HDD, this title can be copied to DVD-RW(VR mode) or
DVD-RAM.
English - 5
Getting Started
• An audio disc on which 44.1kHz PCM Audio is
recorded.
• Plays CD-DA format audio CD-R and CD-RW discs.
• The unit may not be able to play some CD-R or CDRW discs due to the condition of the recording.
DVD-RW Disc Playback and Recording
1-00819S-XSA_01-17
6/9/05
1:45 PM
Page 6
Getting Started
COPY PROTECTION
• Many DVD discs are encoded with copy
protection. Because of this, you should only
connect your HDD & DVD RECORDER directly to
your TV, not to a VCR. Connecting to a VCR
results in a distorted picture from copy-protected
DVD discs.
• This product incorporates copyright protection
technology that is protected by methods claims of
certain U.S. patents and other intellectual
property rights owned by Macrovision Corporation
and other rights owners. Use of this copyright
protection technology must be authorised by
Macrovision Corporation, is intended for home
and other limited viewing uses only unless
otherwise authorised by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.
Protection
This HDD & DVD RECORDER can allow you to protect
the contents of your discs, as described below.
• Programme-protected: See page 95
“Locking(Protecting) a Title”
Using JPEG disc
• CD-R, DVD-R/RW/RAM, HDD with JPEG files
recorded with UDF, ISO9660 or JOLIET format can be
playbacked.
• Only JPEG files with the “.jpg” or “.JPG” extension
can be displayed.
• The unit can handle a maximum of 4,500 files and
1,000 sub folders under a folder.
• MOTION JPEG and progressive JPEG are not
supported.
Using MPEG4 disc
• Disc : CD-RW/-R, DVD-RAM/-RW/-R
• MPEG4 File with following extensions can be played. :
.avi, .divx, .AVI, .DIVX
• MPEG4 Codec format : DivX 3.11 DivX 4.x DivX 5.x
DivX-Pro (without QPEL and GMC)
• Available Audio Format : “MP3”, “MPEG”, “WMA”,
“LPCM”, “AC3”
• Supported subtitle file formats: .smi, .srt, .sub, .psb,
.txt, .ass
• Disc-protected: See page 120 “Disc Protection”
❋ DVD-RAM/-RW/-R discs that are incompatible with
the DVD-VIDEO format cannot be played with this
product.
❋ For more information on DVD recording compatibility,
consult your DVD-RAM/-RW/-R manufacturer.
❋ Use of poor quality DVD-RAM/-RW/-R discs may
cause following unexpected problems including,
without limitation, recording failure, loss of recorded
or edited materials or damage to the recorder.
DVD-RW (VR mode)
• This is a format that is used for recording data on a
DVD-RAM or DVD-RW disc. You can record multiple
titles, edit, delete, partial delete, create a playlist, etc.
• A disc that is recorded in this mode may not be
played by existing HDD & DVD RECORDER.
DVD-RW (V mode)
Disc Format
Using MP3 disc
• CD-R, DVD-R/RW/RAM, HDD with MP3 files recorded
with UDF, ISO9660 or JOLIET format can be
playbacked.
• Only MP3 files with the “.mp3” or “.MP3” extension
can be played.
• For MP3 files recorded with a VBR(Variable Bit
Rates), from 32 Kbps to 320 Kbps, the sound may cut
in out.
• Playable bit-rate range is from 56 Kbps to 320 Kbps.
• The unit can handle a maximum of 1,500 files and
1,000 sub folders under a folder
6 - English
• This is a format that is used for recording data on a
DVD-RW or DVD-R disc. The disc can be played by
existing HDD & DVD RECORDER once it has been
finalised.
• If a disc that has been recorded in Video Mode by a
different maker’s recorder but has not been finalised,
it cannot be played or additionally be recorded by this
recorder.
1-00819S-XSA_01-17
6/9/05
1:45 PM
Page 7
Do not use the following discs!
Getting Started
• LD, CD-G, CD-I, CD-ROM, DVD-ROM, DVD+R and
DVD+RW discs should not be used in this product.
[Note]
Disc types that can be played : CD/CD-RW/-RW/
MP3/JPEG/DVD-Video/DVD-RAM/-RW/-R.
For a DVD-RW/-R disc, which has been recorded in
Video Mode on another component, it can play only
when finalised.
• Some commercial discs and DVD discs purchased
outside your region may not be playable with this
product. When these discs are played, either “No
disc.” or “Please check the regional code of the disc.”
will be displayed.
• If your DVD-RW disc is an illegal copy or is not in
DVD video format, it may also not be playable.
❋ We recommend using one of the discs in the table as
they have been confirmed to be compatible with this
unit. Other discs may not perform correctly.
Media
Disc
TDK
Beall
DVD-R
That’s
Maxell
Panasonic
TDK
Maxell
DVD-RW Optodisc
Radius
Verbatim
Maxell
Fujifilm
DVD-RAM
TDK
Panasonic
Disc
DVD-RAM
DVD-RW
DVD-R
SPEED
4x
4x
4x
4x
4x
2x
2x
2x
2x
2x
3x
3x
2x
3x
Maximum no. of recordings by disc type
100,000
1,000
1
• We take no responsibility and offer no compensation for
any recording failure, loss of recorded or edited material
and/or damage to the recorder arising from usage of
unrecommended discs.
English - 7
1-00819S-XSA_01-17
6/9/05
1:45 PM
Page 8
Getting Started
Contents
Getting Started
Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Precaution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . .3
Handling Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Maintenance of Cabinet . . . . . . . . . . . . . . . . . . . . . . . . . .3
HDD (Hard Disk Drive) . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Disc Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Disc Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Disc Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Disc Copy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
General Features . . . . . . . . . . . . . . . . . . . . . . . . . .10
Before Reading the User’s Manual . . . . . . . . . . . . .11
How to use the HDD & DVD RECORDER . . . . . . .11
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Front Panel Display . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Tour of the Remote Control . . . . . . . . . . . . . . . . . . . . . .17
Connecting & Setting Up
Quick Overview . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Connecting the HDD & DVD RECORDER . . . . . .19
Other type of connecting the Video output cable . . .19
Case 1 : Connecting to a Video (Composite)
output jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Case 2 : Connecting to an S-Video output jack . . . . .20
Case 3 : Component Video output jacks . . . . . . . . . .21
Other type of connecting the Audio output cable .21
Case 1 : Connecting to your TV . . . . . . . . . . . . . . . . .21
Case 2 : Connecting to a stereo amplifier
with AV output jacks . . . . . . . . . . . . . . . . . . . . . . . . .22
Case 3: Connecting to an AV amplifier
with a digital output jack . . . . . . . . . . . . . . . . . . . . . .22
Connecting AV 1 IN, AV 2 IN, DV input jack . . . . .23
Case 1 : Connecting a VCR, Set-Top Box(STB)
or DVD player to the AV 1 IN jacks . . . . . . . . . . . .23
8 - English
Case2 : Connecting a Camcorder to
the AV 2 IN jacks . . . . . . . . . . . . . . . . . . . . . . . . . .23
Case3 : Connecting a Camcorder to
the DV IN jack . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
System Setup
On-Screen Menu Navigation.....................................24
Plug & Auto Setup......................................................25
Setting the Clock........................................................26
Presetting Channels with the Auto Setup function...27
Presetting Channels with the Manual Setup
function .......................................................................28
Setting up the Language Options .............................29
Auto Power Off Setting..............................................30
CM Skip Time Setting................................................31
EP Mode Time Setting...............................................32
Setting up the Front Display Options........................33
Automatic Chapter Creator........................................34
Setting up NICAM Options........................................36
DivX(R) Registration ..................................................36
Setting up the Audio Options.....................................37
Setting up the Video display Options........................38
Setting up the Progressive scan ...............................40
Canceling the Progressive scan ...............................41
Setting up the Parental Control.................................42
If you forgot your password ............................................42
About the Rating Level ...................................................43
About the Change Password .........................................43
Playback
Before Playing............................................................44
Playing a Disc.............................................................45
Using the Disc Menu & Title Menu ...........................46
Using the Search & Skip Functions..........................46
Slow Motion Play/Step Motion Play..........................47
About ANYKEY ..........................................................48
Playing the Title List ...................................................50
Navigation Menu ........................................................51
Using the Markers......................................................54
Using the Bookmarks ................................................56
Selecting the Subtitle Language ...............................58
Selecting the Soundtracks & Audio Channels .........59
Changing the Camera Angle.....................................60
Repeat Play................................................................60
Zooming-In .................................................................62
1-00819S-XSA_01-17
6/9/05
1:45 PM
Page 9
Select Media...............................................................63
Playing an Audio CD/MP3.........................................63
Playing a Picture ........................................................70
Playing an MPEG4 ....................................................73
Copying from DVD to HDD.....................................116
Copying MP3 or JPEG Files
from a Disc to HDD ................................................117
File Copy........................................................................117
Folder Copy ...................................................................118
Disc Manager...........................................................119
Before Recording .......................................................75
Recording the current TV programme you are
watching......................................................................77
Recording from external equipment
you are watching........................................................79
Copying from a Camcorder.......................................80
Making an One Touch Recording (OTR) .................81
Chasing Play ..............................................................82
Simultaneous Recording and Playback ...................83
Making a Timer Recording .......................................84
Flexible Recording (for Timer recording only) ..........86
Editing the Timer Record List....................................86
Deleting a Timer Record List.....................................87
Go To History List.......................................................88
Using the G-Code Feature .......................................91
G-Code Extended ......................................................92
Editing the Disc Name ..................................................119
Disc Protection ..............................................................120
Formatting a Disc ..........................................................121
Delete All Title Lists/Music Lists/Photo Lists................122
Delete All Title Lists ......................................................123
Finalising a Disc ...........................................................124
Unfinalising a Disc (V/VR mode) .................................125
Reference
Troubleshooting ........................................................126
Specifications ...........................................................130
Editing
Basic Editing (Title List) .............................................94
Renaming(Labeling) a Title.............................................94
Locking (Protecting) a Title ............................................95
Deleting a Title.................................................................96
Splitting a Section of a Title (Split)..................................97
Deleting a Section of a Title (Partial Delete)..................99
Advanced Editing (Playlist) .....................................101
Creating a Playlist .........................................................101
Playing Entries in the Playlist .......................................102
Renaming a Playlist Entry ............................................103
Editing a Scene for the Playlist.....................................104
Deleting a Playlist Entry from the Playlist ....................108
Copying from HDD to DVD.....................................109
About the Copy Screen ................................................109
Changing the Record Mode .........................................112
Copying Multiple Titles at One Time.......................112
Deleting an Undesired Title from the Copy List...........114
Previewing a Selected Title from the Copy List...........114
Selecting Record Mode of Each Title
from the Copy List. ........................................................115
English - 9
Getting Started
Recording
Changing Record Mode of All Titles
from the Copy List .........................................................115
1-00819S-XSA_01-17
6/9/05
1:45 PM
Page 10
Getting Started
General Features
The HDD & DVD RECORDER allows you to record and
play high quality digital video on DVD-RAM/-RW/-R or
HDD discs. You can also edit digital images on
DVD-RAM/-RW/-R discs or HDD.
HDD Recording
You can record up to 127 hours of video (in EP mode) on
the internal 80GB (gigabyte) hard disk (HDD).
With both recordable DVD and a high-capacity HDD in the
same recorder, you have the flexibility to keep recordings
on the HDD for quick access anytime, or record to DVD
for archiving or playing on other DVD players.
Automated Quality Adjustment for Timer
Recording
If FR mode is selected, the video quality is adjusted
automatically so that all video for the scheduled time can
be recorded onto the free disc space. (See page 86)
Creating a DVD video title using DVD-RW/-R
disc
With the HDD & DVD RECORDER, you can create your
own DVD Video titles on 4.7 GB DVD-RW/-R discs.
Copying data from a digital camcorder using
a DV input jack
Record DV Device video onto HDD and DVD-RAM/-RW/-R
discs using the DV input jack (IEEE 1394-4pin/4pin).
(See page 80)
High quality progressive scan
Copy between HDD and DVD
You can copy recordings from the HDD to recordable
DVD, or from DVD to the HDD. Usually you can use the
high speed copy feature.
You can also choose to copy material at different
recording quality from the original. For example, you might
want to copy a XP mode (highest quality) recording on the
HDD to SP (standard play) quality on a DVD so that you
can fit other recordings on the same disc.
Simultaneous Recording and Playback
Playback and recording for both DVDs and the built-in
hard disk drive (HDD) are completely independent. For
example you can record a broadcast programme to either
a recordable DVD or the HDD, while watching another
recording you already made on the same DVD or on the
HDD.
High quality digital audio and video recording
and playback
Record up to 16-hours of video with a double sided 9.4
GB DVD-RAM disc, up to 8-hours of images with a 4.7
GB DVD-RAM/-RW/-R disc, depending on the recording
mode.
Selectable Recording Mode
You can set your recorder to one of four different
recording speeds, each varying in recording quality and
length. EP (6Hr or 8Hr) mode yields the most recording
time, LP & SP modes provide less recording time with
higher quality recording, XP mode gives you the highest
quality recording.
10 - English
Progressive scanning provides high resolution and flicker
free video. The 10-bit 54-MHz DAC and 2D Y/C
Separating Circuitry provides the highest image playback
and recording quality. (See pages 40~41)
A variety of functions with an easy-to-use
user interface
The integrated menu system and the messaging
function allow you to perform desired operations both
easily and conveniently. With a HDD, DVD-RAM or
DVD-RW disc, you can edit recorded video, create a
playlist, edit video in a specific sequence according to
your requirements.
MPEG4 playback
This HDD & DVD RECORDER can play MPEG4 formats
within an avi file.
DivX Certification
DivX, DivX Certified, and associated
logos are trademarks of DivXNetworks,
Inc and are used under licence.
1-00819S-XSA_01-17
6/9/05
3:15 PM
Page 11
©2005 Samsung Electronics Co.
All rights reserved; No part or whole of this user’s
manual may be reproduced or copied without the prior
written permission of Samsung Electronics Co.
Make sure to check the following terms before reading
the user manual.
Icons that will be used in manual
Icon
Term
Definition
HDD
This involves a function available
in HDD.
How to use the
HDD & DVD RECORDER
DVD
This involves a function available
in DVD or DVD-R/DVD-RW
discs that have been recorded
and finalised in Video Mode.
RAM
This involves a function available
in DVD-RAM.
RW
This involves a function available
in DVD-RW.
R
This involves a function available
in DVD-R.
CD
This involves a function available
in a data CD (CD-R or CD-RW).
JPEG
This involves a function available
in CD-R/-RW or DVD-R/-RW/
-RAM discs.
MP3
This involves a function available
in CD-R/-RW or DVD-R/-RW/
-RAM discs.
Step 2
MPEG4
This involves a function available
in CD-R/-RW or DVD-R/-RW/
-RAM discs.
Unlike a VCR, the recorder automatically starts
formatting when an unused disc is inserted. This is
required for the preparation of recording on a disc.
This involves a case where a
function does not operate or
settings may be cancelled.
Using a HDD
Caution
NOTE
This involves tips or instructions
on the page that help each
function operate.
One-Touch A function that can be operated
button
by using only one button.
ANYKEY A function that can be operated
button
by using ANYKEY button.
About the use of this user’s manual
1) Be sure to be familiar with Safety Instructions before
using this product. (See pages 2~7)
2) If a problem occurs, check the Troubleshooting.
(See pages 126~129)
Step 1
Select the disc type or HDD
This unit can record on the following types of discs.
If you want to repeatedly record on the same disc
or you want to edit the disc after recording, select a
rewritable DVD-RW or DVD-RAM type disc. If you
want to save a recording without any changes,
choose a non-rewritable DVD-R. You can record
files directly to the built-in HDD or edit a recorded
file.
Format the disc to start recording
Formatting unneccessory.
Using a DVD-RAM
This type of disc can be formatted in DVD-Video
Recording format (VR mode). You can edit
recorded image and create a playlist and edit
images in a specific sequence according to your
requirements.
Using a DVD-RW
This type of disc can be formatted in either DVDVideo format (V mode) or DVD-Video Recording
format (VR mode). For an unused disc, a message
that asks whether to format in VR Mode or not is
displayed. You can play a Video mode disc on
various DVD components. A VR mode disc allows
more varied editing.
Using a DVD-R
This type of disc can be formatted in DVD Video
format. After formatting is complete, you can record
on the disc. You can play this type of discs on
various DVD components only when they have
been finalised.
English - 11
Getting Started
Before Reading the
User’s Manual
Copyright
1-00819S-XSA_01-17
■
NOTE
Getting Started
■
6/9/05
1:45 PM
Page 12
You can only use either the VR or Video
mode on a DVD-RW, but not both at the
same time.
You can change the DVD-RW format to
another format by reinitializing. It should
be noted that the disc's data will be lost
when changing formats.
Step 5
Editing a recorded disc
Editing on discs is easier than conventional video
tapes. The recorder supports many different edit
functions, possible only with DVDs and HDD.
With a simple and easy edit menu, you can operate
various edit functions, such as delete, copy, rename,
lock, etc., on a recorded title.
Step 3
Recording
There are two different recording methods, Direct
Recording and Timer Recording. Timer recording is
classified.
Recording mode : XP (high quality mode), SP
(standard quality mode), LP (long recording mode),
and EP (extended mode) according to the recording
mode. When recording is set in the FR mode, the best
quality picture is recorded with regards to the
remaining time on the disc.
Creating a playlist (DVD-RAM/-RW in VR mode,
HDD)
With this recorder, you can create a new playlist on
the same disc and edit it without the change of the
original recording.
Step 6
Finalising & Playing on
other DVD components
To play your DVD on other DVD components,
finalising may be necessary. First, finish all editing and
recording operations, then finalise the disc.
Step 4
Playing
You can select the title you want to play in a
displayed menu and then immediately start
playback.
A DVD consists of sections, called titles, and sub
sections, called chapters.
During recording, a title is created between two
points where you start and stop recording.
Chapters will be created automatically when you
finalise recording on DVD-RW/-R discs in Video
mode.
The chapter’s length (interval between chapters)
varies according to the recording mode.
12 - English
When using a DVD-RW disc in VR Mode
Although finalising is generally unnecessary when
playing the disc on a VR Mode compatible
component, a finalised disc should be used for
playback on that type of component.
When using a DVD-RW disc in Video Mode
The disc should be finalised first to enable playback
on anything other than this recorder. No more editing
or recording can be made on the disc once it has
been finalised.
To enable recording on the disc again, disc should be
unfinalised.
When using a DVD-R disc
You should finalise the disc to play it on a component
other than this recorder. You cannot edit or record on
the disc once it has been finalised.
1-00819S-XSA_01-17
6/9/05
1:45 PM
Page 13
Unpacking
Setting the Remote Control
Check for the supplied accessories below.
You can control certain functions of another
manufacturer’s TV with this remote control.
Control function buttons involve: TV STANDBY/ON,
PROG
, TV VOL + -, Number buttons, TV MUTE,
INPUT button.
Video/Audio Cable
Remote Control
Instruction Manual
RF Cable for TV
Batteries for Remote
Control (AAA Size)
Quick Guide
Preparing the Remote Control
Install Batteries in the Remote Control
• Open the battery cover on the back of the remote control.
• Insert two AAA batteries. Make sure that the polarities
(+ and -) are aligned correctly.
• Replace the battery cover.
If the remote does not operate properly:
• Check the polarity + - of the batteries (Dry-Cell)
• Check if the batteries are drained.
• Check if remote sensor is blocked by obstacles.
• Check if there is any fluorescent lighting nearby.
Dispose of batteries according to local environmental
regulations. Do not put them in the household trash.
English - 13
Getting Started
Accessories
Getting Started
1-00819S-XSA_01-17
6/9/05
1:45 PM
Page 14
To determine whether your television is
compatible, follow the instructions below.
1. Switch your television on.
2. Point the remote control towards the television.
3. Press and hold the TV STANDBY/ON button and
enter the two-figure code corresponding to the
brand of your television, by pressing the
appropriate number buttons.
Controllable TV Codes
BRAND
SAMSUNG
AIWA
ANAM
BANG & OLUFSEN
BLAUPUNKT
BRANDT
BRIONVEGA
CGE
CONTINENTAL EDISON
DAEWOO
EMERSON
FERGUSON
FINLUX
FORMENTI
FUJITSU
GRADIENTE
GRUNDIG
HITACHI
IMPERIAL
JVC
LG
LOEWE
LOEWE OPTA
MAGNAVOX
METZ
MITSUBISHI
MIVAR
NEC
NEWSAN
NOBLEX
NOKIA
NORDMENDE
PANASONIC
PHILIPS
PHONOLA
PIONEER
RADIOLA
RADIOMARELLI
RCA
REX
SABA
SALORA
SANYO
SCHNEIDER
14 - English
BUTTON
01, 02, 03, 04, 05, 06, 07, 08, 09
82
10, 11, 12, 13, 14, 15, 16, 17, 18
57
71
73
57
52
75
19, 20, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34
64
73
06, 49, 57
57
84
70
49, 52, 71
60, 72, 73, 75
52
61, 79
06, 19, 20, 21, 22, 78
06, 69
06, 57
40
57
06, 48, 62, 65
52, 77
83
68
66
74
72, 73, 75
53, 54, 74, 75
06, 55, 56, 57
06, 56, 57
58, 59, 73, 74
06, 56
57
45, 46
74
57, 72, 73, 74, 75
74
41, 42, 43, 44, 48
06
BRAND
SELECO
SHARP
SIEMENS
SINGER
SINUDYNE
SONY
TELEAVA
TELEFUNKEN
THOMSON
THOMSON ASIA
TOSHIBA
WEGA
YOKO
ZENITH
BUTTON
74
36, 37, 38, 39, 48
71
57
57
35, 48
73
67, 73, 75, 76
72, 73, 75
80, 81
47, 48, 49, 50, 51, 52
57
06
63
Result: If your television is compatible with the remote
control, it will switch off.
It is now programmed to operate with the remote
control.
■
If several codes are indicated for your
television brand, try each one in turn until
you find one that works.
■
If you replace the remote control's
batteries, you must set the brand code
again.
NOTE
Then you can control the television using the following
buttons after the TV button.
Button
TV STANDBY/ON
INPUT
TV VOL (+ -)
PROG (
)
TV MUTE
Number
■
NOTE
Function
Used to switch the television on and off.
Used to select an external source.
Used to adjust the volume of the television.
Used to select the desired channel.
Used to toggle the sound on and off.
Used to input number directly.
The various functions will not necessarily
work on all televisions. If you encounter
problems, operate the television directly.
1-00819S-XSA_01-17
6/9/05
1:45 PM
Page 15
Description
Getting Started
Front Panel
1
2
9
3
10
1. STANDBY/ON BUTTON
Turns the recorder on and off.
2. DVD BUTTON
Select DVD mode.
3. HDD BUTTON
Select HDD mode.
4. DISC TRAY
Opens to accept a disc.
5. DISPLAY
Displays the playing status, title/ chapter/
time, etc.
6. STOP BUTTON
Stops disc playback.
7. SEARCH/SKIP BUTTONS
Goes to the next title/chapter/track or goes
back to the previous title/chapter/track.
4
5
11
6
7
12
8
13
14
8. PROG
BUTTONS
Select TV preset Channels. Same as
PROG button on the remote control.
9. AV 2 INPUT
Connect external equipment.
10. DV-INPUT
Connect external digital equipment with a DV
jack. (such as a camcorder)
11. OPEN/CLOSE BUTTON
Opens and closes the disc tray.
12. PLAY/PAUSE BUTTON
Plays a disc or pauses playback or recording.
13. P.SCAN BUTTON
Selects the progressive scan mode.
14. REC BUTTON
Starts recording.
Front Panel Display
1. Lights when a disc is loaded.
2. Lights in the record mode.
3. Lights to indicate the timer record mode.
4. Lights when a -R/RW/RAM disc is loaded.
5. Playing time/clock/current status indicator.
6. Lights in the progressive scan mode.
English - 15
1-00819S-XSA_01-17
6/9/05
1:45 PM
Page 16
Getting Started
Rear Panel
Fan
The fan always revolves when the power is on.
Ensure a minimum of 10cm clear space on all sides of
the fan when installing the product.
1. DIGITAL AUDIO OUT(OPTICAL)
Connects to an amplifier having a digital optical
audio input jack.
2. DIGITAL AUDIO OUT(COAXIAL)
Connects to an amplifier having a digital coaxial
audio input jack.
3. AV AUDIO OUT
Connects to the audio input of external
equipment using audio cables.
4. AV VIDEO OUT(good video quality)
Connects the input of external equipment using a
Video cable.
5. AV S-VIDEO OUT(better video quality)
Connects the input of external equipment using
an S-Video cable.
6. COMPONENT VIDEO OUT(best video quality)
Connects to equipment having Component video
input jacks.
7. AV 1 AUDIO IN
Connects the output of external equipment using
an audio cables.
8. AV 1 VIDEO IN
Connects the output of external equipment using
a video cable.
9. AV 1 S- VIDEO IN
Connects the output of external equipment using
an S-Video cable.
10. ANT IN (In from aerial connector)
11. ANT OUT (TO TV) (Out to TV connector)
■
NOTE
16 - English
The Antenna connection does not pass
output signal of DVD. To watch a DVD on
your TV, you must connect audio/video
cables.
1-00819S-XSA_01-17
6/9/05
1:45 PM
Page 17
Tour of the Remote Control
13. OK/DIRECTION Buttons (…†œ √ Buttons)
14. RETURN Button
1
20
3
21
4
5
22
7
8
9
10
11
12
23
24
25
26
7
9
27
28
29
13
14
30
15
31
16
32
17
33
18
34
19
35
1. DVD STANDBY/ON Button
2. NUMBER Buttons
3. TV/DVD Button (Not available)
4. DVD Button
Press this to operate DVD.
5. HDD Button
Press this to operate HDD.
6. TV VOL Button
TV volume adjustment
17. COPY Button
Press this when you copy DVD to HDD or HDD to DVD.
To start copying, press the COPY button on the title list
screen or press the COPY button during the playback.
18. REPEAT Button
Allows you to repeat a title, chapter, track or disc.
19. REC PAUSE Button
Use this to pause during recording.
20. TV STANDBY/ON Button
21. AUDIO/TV MUTE Button
Use this to access various audio functions on a disc
(DVD mode).
This operates as sound mute. (TV mode)
22. INPUT Button
Select input signal in external input mode (PROG, AV1,
AV2 or DV input)
23. TV Button
Press this to operate TV.
24. OPEN/CLOSE Button
To open and close the disc tray.
25. CM SKIP Button
When a programme recorded on DVD disc or HDD is
played, the unit can be set to automatically skip a portion
of the programme.
26. PROG Button
Use this to select a TV programme.
27. PLAY/PAUSE Button
Press to play/pause a disc.
28. PLAY LIST/TITLE MENU Button
Use this to return to the Title menu, or to view the
recorded files list.
29. ANYKEY Button
View and select the applicable features under current
status.
30. CANCEL Button
7. REVERSE/FORWARD SKIP Buttons
Press to skip a disc backwards or forwards.
31. SUBTITLE Button
Press this to switch the DVD’s subtitle language.
8. REVERSE/FORWARD STEP Buttons
Each press will play one-frame forward or reverse.
32. TIMER Button
Press to directly enter the Timer Recording Mode menu.
9. REVERSE/FORWARD SEARCH Buttons
Press to search a disc backwards or forwards.
33. MARKER Button
Use this to bookmark a position while playing a disc.
34. REPEAT A-B Button
Allows you to repeat a title, chapter, track or disc.
10. STOP Button
Press to stop a disc.
11. TITLE LIST/DISC MENU Button
Use this to enter the View Recording list/disc menu.
35. REC MODE Button
Use this to set the desired Recording time and picture
quality. (XP/SP/LP/EP)
12. MENU Button
Brings up the HDD & DVD RECORDER’s setup menu.
English - 17
Getting Started
16. REC Button
Use to make a recording on HDD/DVD-RAM/-RW/-R
discs.
2
6
15. INFO Button
This will display current setting or disc status.
2-00819S-XSA_18-23_CONNECT
6/9/05
1:58 PM
Page 18
Connecting & Setting Up
Connecting &
Setting Up
This section involves various methods of
connecting the HDD & DVD RECORDER to
other external components and required initial
setting modes.
Quick Overview
A Quick Overview presented in this guide will give
you enough information to start using the recorder.
Connecting the HDD & DVD RECORDER
†
Other type of connecting the Video
output cable
†
Other type of connecting the Audio
output cable
†
Connecting AV 1 IN, AV 2 IN, DV input jack
Quick Overview . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Connecting the HDD & DVD RECORDER . . . . . .19
Other type of connecting the Video output cable . .19
Other type of connecting the Audio output cable . .21
Connecting AV 1 IN, AV 2 IN, DV input jack . . . . .23
18 - English
2-00819S-XSA_18-23_CONNECT
6/9/05
1:58 PM
Page 19
Connecting the
HDD & DVD RECORDER
Wall
or
■
NOTE
■
There are several ways to output video signal.
Select one of the following video connecting that
best suits you below.
• Case 1 : Connecting to a Video (Composite) output
jack
• Case 2 : Connecting to an S-Video output jack
• Case 3 : Component Video output jacks
S-Video, Component video and Progressive
Output Modes
• S-Video and Component video output are available
only if your TV supports S-Video input or
Component video input, respectively. If S-Video or
Component video output does not work, check the
TV connections and the TV input selection settings.
• Compared to standard interlaced video,
progressive scan doubles the amount of video lines
fed to your TV, resulting in a more stable, flickerfree, clear image than interlaced video. This is only
available with TVs that support progressive scan.
• Progressive Scan Output (576p)
Consumers should note that not all high definition
television sets are fully compatible with this product
and may cause artifacts to be displayed in the
picture, in case of 576 progressive scan picture
problems, It is recommended that the user switch
the connection to the ‘standard definition’ output. If
there are questions regarding our TV set
compatibility with this model 576p HDD & DVD
RECORDER, please contact our customer service
centre.
or
The RF cable connection of this product
sends only signals of TV. You must connect
Audio/Video cables to watch a DVD form your
HDD & DVD RECORDER.
Power off HDD & DVD RECORDER, then you
can watch programmes received through 2 RF
cable.
English - 19
Connecting & Setting Up
1. Disconnect the aerial cable from your TV and
connect it to ANT IN connector on the rear panel of
the HDD & DVD RECORDER.
2. Connect ANT OUT (TO TV) connector of the HDD &
DVD RECORDER and the aerial input of your TV
using the supplied aerial cable.
3. Use the Video/Audio Cable to connect ANALOG
AUDIO OUT(R/L)/VIDEO OUT jacks on the HDD &
DVD RECORDER to the Audio &Video jacks on the
TV.
4. Plug in the HDD & DVD RECORDER and TV
5. Turn on the HDD & DVD RECORDER and TV.
6. Press the INPUT button on your TV remote control
until the Video signal from the HDD & DVD
RECORDER appears on the TV screen.
Other type of connecting
the Video output cable
2-00819S-XSA_18-23_CONNECT
6/9/05
1:58 PM
Page 20
Case 1 : Connecting to a Video
(Composite) output jack
Connecting & Setting Up
1. Connect a video(yellow) cable between the VIDEO
(yellow) OUT jack on HDD & DVD RECORDER and
VIDEO (yellow) INPUT jack on your TV (or AV
amplifier).
• You will enjoy regular quality images.
2. Connect audio cables (white and red) between the
AUDIO OUT jacks on the HDD & DVD RECORDER
and AUDIO IN jacks on TV (or AV amplifier).
(See pages 21~22)
yellow
Video/Audio Cable
20 - English
yellow
Case 2 : Connecting to an S-Video
output jack
1. Connect an S-Video cable (not included) between the
S-VIDEO OUT jack on HDD & DVD RECORDER and
S-VIDEO INPUT jack on your TV (or AV amplifier).
• You will enjoy high quality images.
2. Connect audio cables (white and red) between the
AUDIO OUT jacks on HDD & DVD RECORDER and
AUDIO IN jacks on TV (or AV amplifier).
2-00819S-XSA_18-23_CONNECT
6/9/05
1:58 PM
Page 21
Case 3 : Component Video output
jacks
1. Connect Component video cables (not supplied)
between the COMPONENT OUT(Y,PB,PR) jacks on
HDD & DVD RECORDER and COMPONENT
IN(Y,PB,PR) jacks on your TV.
• You will enjoy high quality and accurate colour
reproduction images.
3. After connecting, refer to the pages 40~41.
There are several ways to connect your HDD & DVD
RECORDER. Select the audio connection that best
suits you below.
• Case 1 : Connecting to your TV
• Case 2 : Connecting to a stereo amplifier with AV
output jacks
• Case 3 : Connecting to an AV amplifier with a
digital output jack
Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D symbol
are trademarks of Dolby Laboratories.
“DTS” and “DTS Digital Out” are trademarks of
Digital Theater Systems, Inc.
green
blue
red
green
Case 1 : Connecting to your TV
If your TV has audio input jacks, use this connection.
blue
red
Progressive setting is only available when
the HDD & DVD RECORDER is connected to
your TV using component cables.
yellow
■
yellow
white
NOTE
Make sure that the colour coded connections
match. The Y, PB, PR component output jacks
of your HDD & DVD RECORDER must be
connected to the exact corresponding
component input jacks on your TV.
red
■
white
red
English - 21
Connecting & Setting Up
2. Connect audio cables (white and red) between the
AUDIO OUT jacks on the HDD & DVD RECORDER
and AUDIO IN jacks on TV (or AV amplifier).
(See pages 21~22).
Other type of connecting
the Audio output cable
2-00819S-XSA_18-23_CONNECT
6/9/05
1:58 PM
Page 22
Case 2 : Connecting to a stereo
amplifier with AV output jacks
If your AV amplifier has a Dolby Digital, MPEG2 or
DTS decoder and a digital input jack, use this
connection. To enjoy Dolby Digital, MPEG2 or DTS
sound, you will need to set up the audio settings.
(See page 37)
Connecting & Setting Up
If your stereo amplifier only has AUDIO INPUT
jacks(L and R), use the AUDIO OUT jacks.
Case 3: Connecting to an AV amplifier
with a digital output jack
red
white
or
red
white
Rear(L)
Rear(R)
Front(L)
Front(L)
speaker
22 - English
Front(R)
speaker
Front(R)
Subwoofer
Centre
2-00819S-XSA_18-23_CONNECT
6/9/05
1:58 PM
Page 23
Connecting AV 1 IN, AV
2 IN, DV input jack
You can also use the AV 2 IN jacks on the front panel of
the HDD & DVD RECORDER. You can record from
connected equipment, such as a camcorder.
When an input source is inserted into AV 2 while
viewing TV, the input will be switched to AV 2
automatically. If the input is not selected automatically,
use INPUT button to select proper input.
• Case 1 : Connecting a VCR, Set-Top Box(STB) or
DVD player to the AV 1 IN jacks
• Case2 : Connecting a Camcorder to the AV 2 IN jacks
• Case3 : Connecting a Camcorder to the DV IN jack
Case 1 : Connecting a VCR, Set-Top
Box(STB) or DVD player to the AV 1 IN
jacks
Camcorder
red
white
yellow
Connecting a VCR or external device to AUDIO/VIDEO
AV 1 IN jacks of the HDD & DVD RECORDER. You can
record from connected equipment (VCR, STB or DVD).
yellow
white
red
VCR
STB
Case 3 : Connecting a Camcorder to
the DV IN jack
DVD
If your camcorder has a DV output jack, connect it to
the DV input jack of your HDD & DVD RECORDER.
or
Camcorder
■
You can also use the AV 2 IN jacks on
the front panel of the HDD & DVD
RECORDER.
■
When the S-Video jack and Video jack
are both connected, the S-Video jack
will have priority.
NOTE
■
Copy protected content cannot be
recorded.
■
NOTE
If the input is not selected automatically,
use INPUT button to select proper input.
English - 23
Connecting & Setting Up
This allows you to connect your HDD & DVD
RECORDER to other external devices and view or
record their outputs.
Case2 : Connecting a Camcorder to
the AV 2 IN jacks
3-00819S-XSA_24-43_SETUP
6/9/05
2:00 PM
Page 24
System Setup
On-Screen Menu
Navigation
The on-screen menus allow you to enable or disable
various functions on your HDD & DVD RECORDER.
Use the following buttons to open and navigate
through the on-screen menus.
Setup
HDD
Title
Music
Photo
Programme
System
√
Clock Set
√
Language
√
Audio
√
Video
√
Parental Control
√
Install
√
System Setup
Setup
MOVE
SELECT
1
MENU Button
2
…†, œ √ Buttons
3
OK Button
4
RETURN Button
On-Screen Menu Navigation . . . . . . . . . . . . . . . . .24
RETURN
EXIT
Press this button on the remote control to open
the on-screen menu.
Press again to exit the on-screen menu.
Plug & Auto Setup . . . . . . . . . . . . . . . . . . . . . . . . .25
Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . . .26
Presetting Channels with the Auto Setup
function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Press these buttons on remote control to move
the selection bar …†, œ √ to cycle through the
menu options.
Presetting Channels with the Manual Setup
function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Setting up the Language Options . . . . . . . . . . . . .29
Auto Power Off Setting . . . . . . . . . . . . . . . . . . . . .30
Press this button on the remote control to confirm any
new settings.
CM Skip Time Setting . . . . . . . . . . . . . . . . . . . . . .31
EP Mode Time Setting . . . . . . . . . . . . . . . . . . . . .32
Setting up the Front Display Options . . . . . . . . . . .33
Automatic Chapter Creator . . . . . . . . . . . . . . . . . .34
Setting up NICAM Options . . . . . . . . . . . . . . . . . .36
DivX(R) Registration . . . . . . . . . . . . . . . . . . . . . . .36
Setting up the Audio Options . . . . . . . . . . . . . . . . .37
Setting up the Video display Options . . . . . . . . . . .38
Setting up the Progressive scan . . . . . . . . . . . . . .40
Canceling the Progressive scan . . . . . . . . . . . . . .41
Setting up the Parental Control . . . . . . . . . . . . . . .42
24 - English
Press this button on the remote control to return to
the Previous MENU screen displayed or to exit the
on-screen MENU.
3-00819S-XSA_24-43_SETUP
6/9/05
2:00 PM
Page 25
Plug & Auto Setup
5
Your HDD & DVD RECORDER will automatically set itself up
when it is plugged in for the first time. TV stations and clock
will be stored in memory. The process takes a few
minutes. Your HDD & DVD RECORDER will then be ready for
use.
Press the …† buttons to select system of
Broadcast in your country, then press the OK
button.
In Australia, select SYSTEM B/B.
In New Zealand, select SYSTEM B/G.
Please select your system
SYSTEM B/B (Australia)
SYSTEM B/G (New Zealand)
Connect the RF cable as indicated on page 19.
(Connecting Your HDD & DVD RECORDER to the
TV Using the RF Cable and Audio/Video Cable.)
2
Plug the HDD & DVD RECORDER into the mains.
“AUTO” in the front panel display flickers.
6
Auto channel scan will be started.
System Setup
1
Channel Scan
Scanning...
10%
3
Press a number button to select the language.
• The number of stations automatically stored by the
HDD & DVD RECORDER depends on the number of
stations that it has found.
Press
Touche
Drücken Sie
Pulse
Premere
Druk op
4
1
2
3
4
5
6
for English
pour Français
Für Deutsch
para Español
per Italiano
voor Nederlands
7
Auto Channel Scan is completed. In 3~4 seconds,
you will see Clock Setting Menu. If you want to
start Clock Setting immediately, Press OK button.
Press the OK button to start the auto setup.
Auto channel scan completed successfully.
OK
Auto setup will be started.
Check antenna and TV cable connection.
Yes
No
English - 25
3-00819S-XSA_24-43_SETUP
8
6/9/05
2:00 PM
Page 26
Check the date and time.
Time
12 : 00
Date
01 / JAN SAT
2005
Setting the Clock
This menu is used to set the current time.
You need to set the time to use timer recording.
1
• if it is : Correct, press OK button then the date
and time will be saved. If you don't press the OK
button, the date and time will be saved
automatically after 5 seconds.
With the unit in Stop mode, press the MENU
button.
Title
HDD
Title
System Setup
Music
Photo
Programme
Setup
MOVE
■
NOTE
Now, HDD & DVD RECORDER is ready
for use. Function for “Plug & Auto Setup”
is fixed already. So if you want to change
this fixed one, you can change it by
Presetting the Stations in OSD
“Presetting Channels with the Manual
setup function” menu. (See page 28)
2
SELECT
RETURN
EXIT
Press the …† buttons to select Setup, then press
the OK or √ button.
Setup
HDD
Title
Music
■
√
Title List
• if it is : Incorrect, input correct Time, Date, Year
using …†œ √ buttons or number buttons.
Press OK button then the date and time will be
saved. When you need to change clock setting,
you can set up it manually. (See page 26)
Auto setup function can be performed by
pressing STOP ( ) on the unit
continuously for 5 seconds or more
during power off with no disc inserted.
Photo
Programme
System
√
Clock Set
√
Language
√
Audio
√
Video
√
Parental Control
√
Install
√
Setup
MOVE
3
SELECT
RETURN
EXIT
Press the …† buttons to select Clock Set, then
press the OK or √ button.
Press the …†œ √ buttons to input Time, Date or
Year. Press the number buttons to input clock
data directly.
The day of the week is displayed automatically.
Clock Set
HDD
Title
Music
Time
Date
12 : 00
01 / JAN SAT 2005
Photo
Programme
Setup
0~9 NUMBER
26 - English
SELECT
RETURN
EXIT
3-00819S-XSA_24-43_SETUP
4
6/9/05
2:00 PM
Page 27
Press the OK button, then the date and time will
be saved. If you don’t press the OK button, it will
not be saved.
4
Press the …† buttons to select Auto Setup, then
press the OK or √ button.
The message “Your data will be lost. Press [OK]
to continue, [Return] to exit.” is displayed.
Install
HDD
Title
Music
Presetting Channels with
the Auto Setup function
1
2
OK
Programme
Setup
SELECT
5
RETURN
EXIT
Press the OK button , then press the …† buttons
to select system of Broadcast in your country.
In Australia, select SYSTEM B/B.
In New Zealand, select SYSTEM B/G.
Install
With the unit in Stop mode, press the MENU
button.
HDD
Please select your system
Title
Music
SYSTEM B/B (Australia)
Press the …† buttons to select Setup, then press
the OK or √ button.
Photo
SYSTEM B/G (New Zealand)
Programme
Setup
MOVE
SELECT
RETURN
EXIT
Setup
HDD
Title
Music
Photo
Programme
System
√
Clock Set
√
Language
√
Audio
√
Video
√
Parental Control
√
Install
√
Setup
MOVE
SELECT
RETURN
EXIT
6
Press the OK button. If you want to exit, press the
MENU button.
Auto Setup
HDD
3
Press the …† buttons to select Install, then press
the OK or √ button.
Title
Please wait.
Music
Photo
11%
Scanning...
Stop
Programme
Install
HDD
Setup
SELECT
Title
Auto Setup
√
Manual Setup
√
RETURN
EXIT
Music
Photo
Programme
Setup
MOVE
SELECT
RETURN
EXIT
English - 27
System Setup
This feature allows you to manually set the HDD & DVD
RECORDER tuner band to Antenna or Cable,
whichever you connected to the Antenna In jack during
initial setup.
Your data will be lost.
PhotoPress [OK] to continue, [Return] to exit.
3-00819S-XSA_24-43_SETUP
6/9/05
2:00 PM
Page 28
• The first frequency band is scanned and the first
station found is displayed and stored. And the
HDD & DVD RECORDER searches for the
second station and so on.
• When the automatic scanning procedure has
finished, the HDD & DVD RECORDER switches
automatically to programme 1.
• The number of stations automatically stored by
the HDD & DVD RECORDER depends on the
number of stations that it has found.
Channel scan will be started. Press the OK button
to stop the Auto Setup.
You can add preset channel that Auto Channel Search
missed. And you can delete a channel you wish to
remove. You can programme the order of channels.
1
With the unit in Stop mode, press the MENU
button.
2
Press the …† buttons to select Setup, then press
the OK or √ button.
System Setup
7
Presetting Channels with
the Manual Setup function
Setup
HDD
Title
Music
Photo
Programme
System
√
Clock Set
√
Language
√
Audio
√
Video
√
Parental Control
√
Install
√
Setup
MOVE
3
SELECT
RETURN
EXIT
Press the …† buttons to select Install, then
press the OK or √ button.
Install
HDD
Title
Auto Setup
√
Manual Setup
√
Music
Photo
Programme
Setup
MOVE
4
SELECT
RETURN
EXIT
Press the …† buttons to select Manual Setup,
then press the OK or √ button.
Manual Setup
PR
01
02
03
04
05
06
07
CH
---------------
MOVE
28 - English
Name
----------------------
SELECT
System
-/-/-/-/-/-/-/-
RETURN
EXIT
3-00819S-XSA_24-43_SETUP
5
6/9/05
2:00 PM
Page 29
Press the …† buttons to select a PR(programme)
you wish to edit, delete, or swap, then press the
ANYKEY button.
Select Edit, Delete or Swap.
Manual Setup
PR
01
02
03
04
Edit05
06
Delete
07
Swap
CH
---------------
MOVE
Name
----------------------
SELECT
If you set the audio, subtitle, disc menu and on-screen
menu, in advance, they will come up automatically
every time you watch a movie.
If the selected language is not recorded on the disc, the
original pre-recorded language is selected.
System
-/-/-/-/-/-/-/-
RETURN
Setting up the Language
Options
EXIT
With the unit in Stop mode, press the MENU
button.
2
Press the …† buttons to select Setup,
then press the OK or √ button.
Manual Setup
PR
CH
Name
MFT
System
01
02
------ --B/B
Setup
HDD
Title
Music
Save
Photo
MOVE
SELECT
Programme
System
√
Clock Set
√
Language
√
Audio
√
Video
√
Parental Control
√
Install
√
Setup
MOVE
- CH : Tune the channel using œ √ buttons.
- Name : Display station name automatically detected
in broadcasting signal. If not detected, you
can edit name by using …†œ √ buttons.
- MFT(Manual Frequency Tunning) : You can tune
up the channel frequency better using œ √ buttons.
- System : Select system of Broadcast in your
country using …† and OK buttons.
In Australia, select SYSTEM B/B.
In New Zealand, select SYSTEM B/G.
3
SELECT
RETURN
EXIT
Press the …† buttons to select Language,
then press the OK or √ button.
Language setup menu will be displayed.
Language
HDD
Title
Music
Photo
Audio
: Original
√
Subtitle
: Automatic
√
Disc Menu
: English
√
On-Screen menu
: English
√
Programme
• In case of Delete : the channel information of
selected PR(programme) will be removed.
Setup
MOVE
SELECT
RETURN
EXIT
• In case of Swap : You can swap the channel
information of two PR(programme). For example,
if you wish to swap PR2 and PR5, select swap at
PR2, then press the OK button at PR5.
English - 29
System Setup
• In case of Edit : You can add or edit
PR(programme) information. After change PR
informations(CH, Name, MFT, System), select
Save, then press the OK button.
1
3-00819S-XSA_24-43_SETUP
4
6/9/05
2:00 PM
Page 30
Press the …† buttons to select the desired
language option, press the OK or √ button.
Auto Power Off Setting
Language
HDD
Audio
Title
Subtitle
Music
Original
: Original
English
: Automatic
Français
Disc Menu
: English
On-Screen menu Deutsch
: English
Español
Photo
√
√
√
√
This feature automatically turns off your HDD & DVD
RECORDER, if you do not press any button for the
selected time.
Italiano
Programme
Nederlands
Setup
Korean
System Setup
MOVE
SELECT
RETURN
EXIT
• Audio : For the disc audio language.
• Subtitle : For the disc subtitles.
• Disc Menu: For the disc menu contained on the
disc
• On-Screen menu: For the on-screen menu of your
HDD & DVD RECORDER.
1
With the unit in Stop mode, press the MENU
button.
2
Press the …† buttons to select Setup, then press
the OK or √ button.
Setup
HDD
Title
5
Press the …† buttons to select the desired
language, then press the OK or √ button.
Music
Photo
Programme
System
√
Clock Set
√
Language
√
Audio
√
Video
√
Parental Control
√
Install
√
Setup
MOVE
■
NOTE
■
Press the RETURN or œ button to return
to the previous menu. Press the MENU
button to exit the menu.
The selected language will only appear if
it is supported on the disc.
3
SELECT
RETURN
EXIT
Press the …† buttons to select System,
then press the OK or √ button.
System menu will be displayed.
System
HDD
Title
Music
Photo
Programme
Auto Power Off : Off
√
CM Skip Time
: 15 Sec
√
EP Mode Time
: 6 Hour
√
Front Display
: Auto Dim
√
Chapter Creator : Off
√
NICAM
√
: On
√
DivX(R) Registration
Setup
MOVE
4
SELECT
RETURN
EXIT
Press the …† buttons to select Auto Power Off,
then press the OK or √ button.
System
HDD
Title
Music
Photo
Programme
Auto Power Off : Off
Off
√
CM Skip Time
: 152 Sec
Hour
√
EP Mode Time
: 6 6Hour
Hour
√
Front Display
: Auto Dim
√
Chapter Creator : Off
√
NICAM
√
: On
DivX(R) Registration
√
Setup
MOVE
30 - English
SELECT
RETURN
EXIT
3-00819S-XSA_24-43_SETUP
5
6/9/05
2:00 PM
Page 31
Press the …† buttons to select the desired item,
then press the OK or √ button.
CM Skip Time Setting
• Off : Auto power off is disabled.
• 2 Hour : DVD-HDD Receiver will automatically
turns off for 2 hours after the last button
is pressed.
• 6 Hour : DVD-HDD Receiver will automatically
turns off for 6 hours after the last button
is pressed.
• If turn off time set by automatic Power off
function is reached during a playback or
recording, the device will operate until the
playback or recording is over.
When a programme recorded on a HDD, a DVD-RAM, a
DVD-RW, or a DVD-R is played, the unit can be set to
automatically skip a portion of the programme
corresponding to a CM(commercial) skip time set by the
user.
With the unit in Stop mode, press the MENU
button.
2
Press the …† buttons to select Setup, then press
the OK or √ button.
Setup
HDD
Title
Music
Photo
Programme
System
√
Clock Set
√
Language
√
Audio
√
Video
√
Parental Control
√
Install
√
Setup
MOVE
3
SELECT
RETURN
EXIT
Press the …† buttons to select System, then
press the OK or √ button.
System menu will be displayed.
System
HDD
Title
Music
Photo
Programme
Auto Power Off : Off
√
CM Skip Time
: 15 Sec
√
EP Mode Time
: 6 Hour
√
Front Display
: Auto Dim
√
Chapter Creator : Off
√
NICAM
√
: On
DivX(R) Registration
√
Setup
MOVE
SELECT
RETURN
EXIT
English - 31
System Setup
1
3-00819S-XSA_24-43_SETUP
4
6/9/05
2:00 PM
Page 32
Press the …† buttons to select CM Skip Time,
then press the OK or √ button.
EP Mode Time Setting
System
HDD
Title
Music
Auto Power Off : Off
√
CM Skip Time
: 1515Sec
Sec
√
EP Mode Time
: 6 30
Hour
Sec
√
: Auto
Dim
60 Sec
Chapter Creator : Off
√
NICAM
√
Front Display
Photo
Programme
: On
DivX(R) Registration
√
√
Setup
System Setup
MOVE
SELECT
RETURN
EXIT
5
Press the …† buttons to select the desired time
interval, then press the OK or √ button.
6
If you press the CM SKIP button during playback,
the section corresponding to the set time is
skipped, and then the next section is played.
You can select one of four recording modes by pressing
the REC MODE button repeatedly.
EP mode is one of four REC Mode (XP, SP, LP, EP).
In EP(Extended Play) mode, you can set recording time
to 6 or 8 hours by this setting.
1
With the unit in Stop mode, press the MENU
button.
2
Press the …† buttons to select Setup, then press
the OK or √ button.
Setup
HDD
■
NOTE
■
CM Skip can be performed only during
normal playback.
Title
Music
Photo
When the time set is more than a
remaining time of a current title: The next
title is played from the beginning.
Programme
When the time set is more than a
remaining time of a play list, the next
scene is played.
■
CM Skip does not work in a still picture
mode.
■
When a set time is less than a remaining
time of a scene, a last title, or a last track
that is displayed currently, a prohibition
mark appears.
■
■
CM Skip releases Repeat (including
Repeat A-B, Chapter, and Title).
CM Skip may not operate with some
DVD-Video discs.
32 - English
√
Clock Set
√
Language
√
Audio
√
Video
√
Parental Control
√
Install
√
Setup
MOVE
■
System
3
SELECT
RETURN
EXIT
Press the …† buttons to select System, then
press the OK or √ button.
System menu will be displayed.
System
HDD
Title
Music
Photo
Programme
Auto Power Off : Off
√
CM Skip Time
: 15 Sec
√
EP Mode Time
: 6 Hour
√
Front Display
: Auto Dim
√
Chapter Creator : Off
√
NICAM
√
: On
DivX(R) Registration
√
Setup
MOVE
SELECT
RETURN
EXIT
3-00819S-XSA_24-43_SETUP
4
6/9/05
2:00 PM
Page 33
Press the …† buttons to select EP Mode Time,
then press the OK or √ button.
Setting up the Front
Display Options
System
HDD
Title
Music
Auto Power Off : Off
√
CM Skip Time
: 15 Sec
√
EP Mode Time
: 6 6Hour
Hour
√
: Auto
Dim
8 Hour
Chapter Creator : Off
√
NICAM
√
Front Display
Photo
Programme
: On
DivX(R) Registration
Adjust the brightness of the unit’s front panel display.
√
√
Setup
MOVE
5
SELECT
RETURN
EXIT
Press the …† buttons to select the desired Time,
then press the OK or √ button.
1
With the unit in Stop mode, press the MENU
button.
2
Press the …† buttons to select Setup, then press
the OK or √ button.
Title
Music
Photo
Programme
System
√
Clock Set
√
Language
√
Audio
√
Video
√
Parental Control
√
Install
√
Setup
MOVE
3
SELECT
RETURN
EXIT
Press the …† buttons to select System, then
press the OK or √ button.
System menu will be displayed.
System
HDD
Title
Music
Photo
Programme
Auto Power Off : Off
√
CM Skip Time
: 15 Sec
√
EP Mode Time
: 6 Hour
√
Front Display
: Auto Dim
√
Chapter Creator : Off
√
NICAM
√
: On
DivX(R) Registration
√
Setup
MOVE
SELECT
RETURN
EXIT
English - 33
System Setup
Setup
HDD
3-00819S-XSA_24-43_SETUP
4
6/9/05
2:00 PM
Page 34
Press the …† buttons to select Front Display,
then press the OK or √ button.
System
Automatic Chapter
Creator
HDD
Title
Music
Photo
Programme
Auto Power Off : Off
√
CM Skip Time
: 15 Sec
√
EP Mode Time
: 6 Hour
√
Front Display
: Auto
Dim
Bright
√
Chapter Creator : Off
Dim
NICAM
: On
Auto Dim
DivX(R) Registration
√
√
(V mode)
√
Setup
MOVE
System Setup
5
SELECT
RETURN
EXIT
Press the …† buttons to select the desired item,
then press the OK or √ button.
• Bright : Makes the Front Panel Display bright.
• Dim : Makes the Front Panel Display dim.
• Auto Dim : Makes the Front Panel Display dim
automatically when the set is in
power off.
1
With the unit in Stop mode, press the MENU
button.
2
Press the …† buttons to select Setup, then press
the OK or √ button.
Setup
DVD-RW(V)
Title
Music
Photo
Programme
System
√
Clock Set
√
Language
√
Audio
√
Video
√
Parental Control
√
Install
√
Setup
MOVE
3
SELECT
RETURN
EXIT
Press the …† buttons to select System, then
press the OK or √ button.
System menu will be displayed.
System
DVD-RW(V)
Title
Music
Photo
Programme
Auto Power Off : Off
√
CM Skip Time
: 15 Sec
√
EP Mode Time
: 6 Hour
√
Front Display
: Auto Dim
√
Chapter Creator : Off
√
NICAM
√
: On
DivX(R) Registration
√
Setup
MOVE
34 - English
SELECT
RETURN
EXIT
3-00819S-XSA_24-43_SETUP
4
6/9/05
2:00 PM
Page 35
Press the …† buttons to select Chapter Creator,
then press the OK or √ button.
System
DVD-RW(V)
Title
Music
Photo
Auto Power Off : Off
√
CM Skip Time
: 15 Sec
√
EP Mode Time
: 6 Hour
√
Front Display
: Auto Dim
√
Chapter Creator : Off
Off
√
NICAM
√
: On
On
DivX(R) Registration
Programme
8
Press the STOP button to stop recording.
9
To display the created titles, finalise the disc
(See page 124) and then press the TITLE MENU
button. The title menu will be displayed.
√
Setup
MOVE
5
SELECT
RETURN
EXIT
Press the …† buttons to select the desired item,
then press the OK or √ button.
10
Press the MENU button to exit the menu.
6
Press the REC button to start recording. (See
page 78 about how to set recording speed) The
message “Do you want to create the chapter
menu after this recording?” is displayed.
Top
Next
To display the created chapters, select the
desired Title and then press the DISC MENU
button. The chapter menu for the selected Title
will be displayed.
CHAPTER
Previous
Top
Next
Do you want to create the chapter menu
after this recording?
Yes
The Automatic Chapter Creator function does
No
Caution
7
not work during Timer Recording or when you
turn the power off.
Press the œ √ buttons to select Yes and press
the OK button.
• A new chapter is created according to the selected
recording mode. A chapter will be about 5 minutes
long in XP and SP, and about 15 minutes long in LP
and EP mode.
English - 35
System Setup
• Off: Select this option when you do not want
Automatic Chapter Creator.
• On: Select this option when you want Automatic
Chapter Creator.
Previous
3-00819S-XSA_24-43_SETUP
6/10/05
10:52 AM
Page 36
Setting up NICAM
Options
4
Press the …† buttons to select NICAM, then
press the OK or √ button.
System
HDD
NICAM programmes are divided into 3 types. NICAM
Stereo, NICAM Mono and Bilingual (transmission in
another language). NICAM programmes are always
accompanied by a standard mono sound broadcast and
you can select the desired sound by setting NICAM on
or off.
System Setup
1
2
With the unit in Stop mode, press the MENU
button.
Press the …† buttons to select Setup, then press
the OK or √ button.
Title
Music
Photo
Auto Power Off : Off
√
CM Skip Time
: 15 Sec
√
EP Mode Time
: 6 Hour
√
Front Display
: Auto Dim
√
Chapter Creator : Off
Programme
√
Off
: On
√
DivX(R) RegistrationOn
√
NICAM
Setup
MOVE
5
SELECT
RETURN
EXIT
Press the …† buttons to select Off or On, then
press the OK or √ button.
• Off: Only set at this position to record the
standard mono sound during a NICAM
broadcast if the stereo sound is distorted
due to inferior reception conditions.
• On: NICAM mode
Setup
HDD
Title
Music
Photo
Programme
System
√
Clock Set
√
Language
√
Audio
√
Video
√
Parental Control
√
Install
√
Setup
MOVE
3
SELECT
RETURN
Press the …† buttons to select System,
then press the OK or √ button.
System menu will be displayed.
System
HDD
Title
Music
Photo
Programme
Auto Power Off : Off
√
CM Skip Time
: 15 Sec
√
EP Mode Time
: 6 Hour
√
Front Display
: Auto Dim
√
Chapter Creator : Off
√
NICAM
√
: On
DivX(R) Registration
√
Setup
MOVE
36 - English
SELECT
RETURN
DivX(R) Registration
EXIT
EXIT
Please use the Registration code to register this HDD &
DVD RECORDER with the DivX(R) Video On Demand
format. For more information, visit www.divx.com/vod.
3-00819S-XSA_24-43_SETUP
6/9/05
2:01 PM
Page 37
Setting up the Audio
Options
You can connect the HDD & DVD RECORDER to an
external amp or Home theatre.
Allow you to setup the Audio device and sound status
depending on the audio system in use.
2
Press the …† buttons to select Setup, then press
the OK or √ button.
1. PCM : Select this when you have no
equipment that can decode Dolby
Digital (or MPEG-2) signal. When you
play Dolby Digital (or MPEG-2) sound
track, the digital output are converted to
PCM Stereo.
2. Bitstream : Output Dolby Digital (or MPEG-2)
audio as bitstream. Select this
when your AV receiver or AV
amplifier have Dolby Digital (or
MPEG-2) Decoder.
■
Digital output setting is equally applied to
both Dolby Digital and MPEG-2 audio.
LPCM sound track is always outputted as
PCM. It has no relation with Digital
Output setting.
■
Be sure to select the correct Digital
Output or you will hear no sound or loud
noise.
NOTE
Setup
HDD
Title
Music
Photo
Programme
System
√
Clock Set
√
Language
√
Audio
√
Video
√
Parental Control
√
Install
√
DTS
Setup
MOVE
SELECT
RETURN
EXIT
1. Off : Doesn’t output DTS signal. Select this
when your AV receiver or AV amplifier
does not have DTS decoder.
3
Press the …† buttons to select Audio, then press
the OK or √ button.
Audio setup menu will be displayed.
2. On : Outputs DTS Bitstream via digital output
when you play DTS track. Select this only
when your AV receiver (or AV amplifier)
have DTS decoder.
Audio
HDD
Title
Music
Photo
Digital Output
: PCM
√
DTS
: Off
√
Dynamic Compression : On
√
V-Mode Compatibility
√
: Off
■
NOTE
When DTS soundtrack is played, sound
does not output from AV Audio Output.
Programme
Setup
MOVE
SELECT
RETURN
EXIT
Dynamic Compression
4
Press the …† buttons to select the desired audio
option, then press the OK or √ button.
5
Press the …† buttons to select the desired item,
then press the OK or √ button.
■
NOTE
Press the RETURN or œ button to return
to the previous menu.
Press the MENU button to exit the menu.
This is only active when a Dolby Digital signal is
detected.
1. On : When Movie soundtracks are played at
low volume or from smaller speakers, the
system can apply appropriate
compression to make low-level content
more intelligible and prevent dramatic
passages from getting too loud.
2. Off : You can enjoy the movie with the
standard Dynamic Range.
English - 37
System Setup
1
With the unit in Stop mode, press the MENU
button.
Digital Output
3-00819S-XSA_24-43_SETUP
6/9/05
2:01 PM
Page 38
V-Mode Compatibility
This feature is about the setup for selecting
audios when recording the NICAM STEREO
(Multi-audio) broadcasting on HDD. It does not
affect to the direct DVD recording of a
programme.
1. Off : Both “DUAL L” and “DUAL R” of the multiaudio broadcasting are recorded on
HDD.Titles recorded on HDD under such
setup status cannot be copied to V mode
(DVD-RW/-R).
System Setup
2. On : Either “DUAL L” or “DUAL R” of the multiaudio broadcasting is recorded on
HDD.Titles recorded on HDD under such
setup status can be copied to DVD-R or
DVD-RW (V mode). “DUAL L” and “DUAL
R” options can be selected from “Audio
Selection.”
Setting up the Video
display Options
This function allows you to setup the TV screen
settings. This function depends on disc type. It may
not work for some disc types.
1
With the unit in Stop mode, press the MENU
button.
2
Press the …† buttons to select Setup, then press
the OK or √ button.
Audio
HDD
Title
Digital Output
: PCM
√
DTS
: Off
√
Dynamic Compression : On
√
Music
Photo
V-Mode CompatibilityOff : Off
√
Setup
HDD
Title
On
Music
Programme
Photo
Setup
Programme
MOVE
SELECT
RETURN
EXIT
System
√
Clock Set
√
Language
√
Audio
√
Video
√
Parental Control
√
Install
√
Setup
MOVE
SELECT
RETURN
EXIT
Audio
HDD
Title
Music
Photo
Digital Output
: PCM
√
DTS
: Off
√
Dynamic Compression : On
√
V-Mode Compatibility
: On
√
Audio Selection
: DUAL L √
Programme
Setup
MOVE
SELECT
RETURN
3
Press the …† buttons to select Video, then press
the OK or √ button.
Video setup menu will be displayed.
EXIT
Video
HDD
TV Aspect
Title
: 16:9 Wide
3D Noise Reduction : Off
√
√
Music
Photo
Programme
Setup
MOVE
38 - English
SELECT
RETURN
EXIT
3-00819S-XSA_24-43_SETUP
6/9/05
2:01 PM
Page 39
Press the …† buttons to select the desired video
option, then press the OK or √ button.
4
3D Noise Reduction (motion
adaptive noise reduction)
Video
Video
HDD
HDD
√
: 16:9
Wide Box
4:3 Letter
3D Noise Reduction : Off
4:3 Pan/Scan√
TV Aspect
Title
Music
√
Programme
Setup
Setup
MOVE
SELECT
RETURN
EXIT
Press the …† buttons to select the desired item,
then press the OK or √ button.
MOVE
SELECT
RETURN
EXIT
1. Off : Normal
2. On : Provides a cleaner picture through noise
reduction (for recording).
Press the RETURN or œ button to return
to the previous menu.
Press the MENU button to exit the menu.
System Setup
NOTE
√
On
Photo
Programme
■
: 16:9 Wide
3D Noise Reduction :Off
Off
Music
16:9 Wide
Photo
5
TV Aspect
Title
TV Aspect
Depending on the type of television you have,
you may want to adjust the screen setting.
(aspect ratio)
1. 4:3 Letter Box : Select when you want to see
the total 16:9 ratio screen
DVD supplies, even though
you have a TV with a 4:3 ratio
screen. Black bars will appear
at the top and bottom of the
screen.
2. 4:3 Pan/Scan : Select this for conventional
size TV when you want to see
the central portion of the 16:9
screen. (Extreme left and right
side of movie picture will be cut
off.)
3. 16:9 Wide : You can view the full 16:9 picture
on your widescreen TV.
English - 39
3-00819S-XSA_24-43_SETUP
6/10/05
10:52 AM
Page 40
Setting up the
Progressive scan
3
The message “Video Output Mode Progressive
Scan” will appear.
If the TV supports Progressive Scan, press the P.SCAN
button on the front of the HDD & DVD RECORDER to
enjoy.
If you select “Progressive scan mode”, the component
cable has to be connected at first. (see page 21)
System Setup
1
With the unit in Stop mode, press the P.SCAN button
on the front of the HDD & DVD RECORDER.
The message “Press [Yes] to confirm Progressive
scan mode. Otherwise, press [No]” will appear.
Press the œ √ buttons to select Yes, and then
press the OK button.
Press [Yes] to confirm Progressive scan mode.
Otherwise, press [No]
Yes
2
No
The message “Please, set your TV to Progressive
input. To deactivate, press [STOP] key.” will
appear. Press the OK button.
Please, set your TV to Progressive input,
To deactivate, press [STOP] key.
OK
40 - English
Video Output Mode
Progressive Scan
■
If the P.SCAN button on the HDD & DVD
RECORDER’s front panel is pressed
during playback, the message “This
function is possible only on stop mode”
appears on the screen.
■
Progressive setting is only available when
the HDD & DVD RECORDER is in stop
mode.
NOTE
3-00819S-XSA_24-43_SETUP
6/9/05
2:01 PM
Page 41
Canceling the
Progressive scan
1
With the unit in Stop mode, press the P.SCAN button
on the front of the HDD & DVD RECORDER.
The message “Press [Yes] to confirm Interlace
scan mode. Otherwise, press [No]” will appear.
Press the œ √ buttons to select Yes, and then
press the OK button.
■
NOTE
■
Do not press the P.SCAN button if you are
using a TV that does not support
Progressive mode. Nothing will be
displayed on the screen if pressed.
If you press the P.SCAN button by mistake
when your TV does not support Progressive
mode, you need to release the Progressive
mode. To release the Progressive mode,
press the P.SCAN button on the front panel
3 times. The screen will recover after the
PS indicator on the front panel display
turns off.
System Setup
Press [Yes] to confirm Interlace scan mode.
Otherwise, press [No]
Yes
2
No
The message “Please, set your TV to Interlace
input. To deactivate, press [STOP] key.” will
appear. Press the OK button.
Please, set your TV to Interlace input,
To deactivate, press [STOP] key.
OK
3
The message “Video Output Mode Interlace Scan”
will appear.
Video Output Mode
Interlace Scan
English - 41
3-00819S-XSA_24-43_SETUP
6/9/05
2:01 PM
Page 42
Setting up the Parental
Control
Enter the 4-digit password using the number
buttons on the remote control.
The “Confirm the password” message will be
displayed. Enter your password again.
4
Parental Control
The Parental Control function works in conjunction with
DVDs that have been assigned a rating which helps you
control the types of DVDs that your family watches.
There are up to 8 rating levels on a disc.
HDD
Title
Confirm the password
Music
Photo
Programme
Setup
System Setup
0~9 NUMBER
1
With the unit in Stop mode, press the MENU
button.
2
Press the …† buttons to select Setup, then press
the OK or √ button.
SELECT
RETURN
EXIT
Press the OK or √ button to select Password.
5
Parental Control
HDD
Password
Title
HDD
: Off
Off
√
On
Music
Setup
Photo
Title
Music
Photo
Programme
System
√
Clock Set
√
Language
√
Audio
√
Video
√
Parental Control
√
Install
√
Programme
Setup
MOVE
SELECT
RETURN
EXIT
Setup
MOVE
SELECT
RETURN
EXIT
Press the …† buttons to select On or Off, then
press the OK or √ button.
6
3
Press the …† buttons to select Parental Control,
then press the OK or √ button.
■
NOTE
Parental Control
Press the RETURN or œ button to return
to the previous menu.
Press the MENU button to exit the menu.
HDD
Title
Create the password
Music
Photo
If you forgot your password
Programme
Setup
0~9 NUMBER
42 - English
SELECT
RETURN
EXIT
1
Remove the disc.
2
Press and hold the SEARCH/SKIP ( ) button on
the front panel for 5 seconds or more.
3-00819S-XSA_24-43_SETUP
6/9/05
2:01 PM
Page 43
About the Rating Level
1
About the Change Password
Press the …† buttons to select Rating Level,
then press the OK or √ button.
1
Press the …† buttons to select Change Password,
then press the OK or √ button.
Parental Control
HDD
Parental Control
Title
Music
Password
: On
√
Rating Level
: Level1 - Kids
√
HDD
Title
√
Change Password
Photo
Music
Programme
Photo
Password
: On
√
Rating Level
: Level1 - Kids
√
√
Change Password
Programme
Setup
MOVE
SELECT
RETURN
Setup
EXIT
MOVE
SELECT
RETURN
EXIT
Parental Control
HDD
Change Password
Title
Level8 - Adults√
: On
Rating Level
Level7
√
: Level
8 (Adults)√
Change Password
Level6
HDD
Title
√
Level5
Photo
Level3
Programme
Enter the password
Music
Level4
Photo
Level2
Setup
Programme
Level1 - Kids
MOVE
SELECT
RETURN
Setup
EXIT
0~9 NUMBER
2
Press the …† buttons to select the rating level
you want, then press the OK or √ button.
3
When you operate your HDD & DVD RECORDER
for the first time, the “Create the Password”
message will be displayed.
For example, if you select up to Level 6, discs that
contain Level 7, 8 will not play. A larger number
indicates that the programme is intended for adult
use only.
2
SELECT
RETURN
EXIT
Enter the 4-digit password using the number
buttons on the remote control.
The “Confirm the password” message will be displayed.
Change Password
HDD
Title
Confirm the password
Music
Photo
Programme
Setup
0~9 NUMBER
3
SELECT
RETURN
EXIT
Enter your password again using the number
buttons on the remote control.
■
See page 42 if you forgot your password.
NOTE
English - 43
System Setup
Music
Password
4-00819S-XSA_44-58_Play
6/9/05
2:06 PM
Page 44
Before Playing
Playback
Read the following information before playing a disc.
This section introduces basic functions of
playback and playback by disc type.
Dolby Digital
DTS
Region code (DVD-Video only)
Both the HDD & DVD RECORDER and the discs are coded
by region. These regional codes must match in order for the
disc to play. If the codes do not match, the disc will not play.
The Region Number for this HDD & DVD RECORDER is
described on the rear panel of the HDD & DVD RECORDER.
Digital Audio
Disc types that can be played
Stereo
PAL broadcast
system in U.K, France,
Germany, etc.
MP3
Playback
DivX
Disc Types
DVD-VIDEO
AUDIO-CD
DVD-RAM
Before Playing.....................................................................44
Playing a Disc......................................................................45
DVD-RW
Using the Disc Menu & Title Menu ....................................46
Using the Search & Skip Functions...................................46
Slow Motion Play/Step Motion Play...................................47
DVD-R
About ANYKEY ...................................................................48
Playing the Title List ............................................................50
Navigation Menu .................................................................51
Using the Markers...............................................................54
CD-RW/-R
DVD-RAM/
-RW/-R
Using the Bookmarks .........................................................56
Selecting the Subtitle Language ........................................58
HDD
Selecting the Soundtracks & Audio Channels ..................59
Changing the Camera Angle..............................................60
Repeat Play.........................................................................60
Playing an Audio CD/MP3..................................................63
Playing a Picture .................................................................70
Playing an MPEG4 .............................................................73
44 - English
Disc Shape
Max. Playing Time
Single sided(12cm)
240
Double sided(12cm)
480
AUDIO + VIDEO
Single sided(8cm)
80
Double sided(8cm)
160
Single sided(12cm)
74
AUDIO
Single sided(8cm)
20
1 (XP: Excellent Quality)
Single-sided
2 (SP: Standard Quality)
12cm (4.7GB) 4 (LP: Long Playback)
6 or 8 (EP:Extended)
AUDIO + VIDEO
2 (XP: Excellent Quality)
Double-sided 4 (SP: Standard Quality)
12cm (9.4GB) 8 (LP: Long Playback)
12 or 16 (EP:Extended)
1 (XP: Excellent Quality)
2 (SP: Standard Quality)
AUDIO + VIDEO 12cm (4.7GB)
4 (LP: Long Playback)
6 or 8 (EP:Extended)
1 (XP: Excellent Quality)
2 (SP: Standard Quality)
AUDIO + VIDEO 12cm (4.7GB)
4 (LP: Long Playback)
6 or 8 (EP:Extended)
JPEG
MP3
MPEG4
Approx. 18 (XP: Excellent Quality)
Approx. 34 (SP: Standard Quality)
AUDIO + VIDEO
Approx. 65 (LP: Long Playback)
Approx. 96 or Approx. 127
(EP:Extended)
Discs that cannot be played
Zooming-In ..........................................................................62
Select Media........................................................................63
Disc Logo Recorded content
•
•
•
•
DVD-Video with a region number other than “4” or “ALL”
12cm 2.6 GB and 5.2 GB DVD-RAM
3.9 GB DVD-R Disc for Authoring.
DVD-RAM/-RW(VR mode) not recorded following the Video
Recording Standard
• Unfinalised DVD-R,unfinalised DVD-RW(V mode) recorded on
other equipment.
• DVD-ROM/DVD+RW/PD/MV-Disc, etc
• CVD/CD-ROM/CDV/CD-G/CD-I
4-00819S-XSA_44-58_Play
■
NOTE
■
■
■
■
6/9/05
2:06 PM
Page 45
This HDD & DVD RECORDER can only
operate with discs that are compatible with
DVD-RAM Standard Version 2.0.
Playback and/or recording may not work for
some types of discs, or when specific
operations, such as angle change and
aspect ratio adjustment, are being
performed. Information about the discs is
written in detail on the box. Please refer to
this if necessary.
Do not allow the disc to become dirty or
scratched, finger prints, dirt, dust, scratches
or deposits of cigarette smoke on the
recording surface may make it impossible to
use the disc for recording.
DVD-RAM/-RW/-R discs may not be able to
play on some DVD players, depending on
the player, disc and the condition of the
recording.
Discs with NTSC programmes recorded on
them cannot be recorded using this product.
1
Press the OPEN/CLOSE button.
2
Place a disc gently into the tray with the disc’s
label facing up.
3
Press OPEN/CLOSE button to close the disc tray.
• Your HDD & DVD RECORDER closes the disc
tray and plays the disc automatically.
• The recorder does not play discs automatically
after the initial power on.
• When the recorder is powered on and a disc is in
•
•
•
Playing a Disc
•
Press the STOP(
) button to stop playback.
■
When you stop playing back a disc, the HDD & DVD
RECORDER remembers where you stopped, so
when you press PLAY( ) button again, it will pick
up where you left off. (Unless the disc is removed or
the HDD & DVD RECORDER is unplugged, or if you
press the STOP( ) button twice.)
■
Do not move your HDD & DVD RECORDER
while playing, as this may cause damage to
the disc.
Make sure to press the OPEN/CLOSE
button to open or close the disc tray.
Do not push the disc tray while it is being
opened or closed, as this may cause a
product malfunction.
Do not place foreign materials on or in the
disc tray.
Some functions may perform differently or
be disabled depending on the disc type.
If this occurs, refer to the instructions
written on the disc case.
Be especially careful that children's fingers
are not caught between the disc tray and
the tray chassis when it closes.
You must only insert one DVD disc at a
time. Inserting two or more discs will not
allow playback and may cause damage to
the HDD & DVD RECORDER.
NOTE
Caution
■
■
■
■
■
■
English - 45
Playback
4
the tray, the unit will be activated and wait in stop
status.
Press the PLAY( ) button to start playback.
If you insert an MP3 Disc, your HDD & DVD
RECORDER will display the file list on the
screen and start playing.
If you insert a JPEG Disc, folders and files are
displayed in the thumbnail picture.
If you want the unit to play automatically when it
is powered on with a disc in the unit, power on
with the PLAY( ) button.
4-00819S-XSA_44-58_Play
6/9/05
2:06 PM
Page 46
Using the Disc Menu &
Title Menu
Using the Search & Skip
Functions
Searching through a Chapter or
Track
Some type of discs contain a dedicated menu system that
allows you to select special functions for title, chapter, audio
track, subtitle, film preview, information on characters, etc.
For DVD-VIDEO Disc
Press the DISC MENU button to enter the disc menu
of the disc.
1
• Move to the setup menu related to playback
operation.
• You can select audio language and subtitle etc.
provided by the disc.
Press the TITLE MENU button to move to the title
menu of the disc.
• Press this button if the disc contains more than one
title. Some discs may not support the title menu
functionality.
Playback
2
1
HDD/
DVD-VIDEO/
DVD-RAM/-RW/-R
Fast X 2 ➞
Fast X 8 ➞
Fast X 32 ➞
MPEG4
AUDIO CD
(CD-DA)
X2➞
PLAY (
NOTE
■
Title List : Title List shows a list to help
you select a title. Since the title
list consists of the information
on video stream that is actually
recorded, if one title is deleted,
that title cannot be played
again.
Play List : This refers to a unit of playback,
which is made by selecting a
desired scene in the entire Title
List. When one playlist is
played, only the scene selected
by the user will play and then
stop. Since only the information
necessary for playing a desired
scene is included in a playlist,
even if that playlist is deleted,
the original recording will not be
deleted. (only VR mode)
46 - English
Fast X 4 ➞
Fast X 16 ➞
Fast X 128
X4➞
X8
) button.
• When you press and hold the SEARCH (
)
buttons, playback is done at the default speed of
X4.
If you release the SEARCH (
) buttons ,
playback is performed at a normal speed.
• The speed marked in this function may be
different from the actual playback speed.
Press the TITLE LIST button to display title list.
■
) buttons on
• You can scan the programme in reverse.
To return to normal speed playback, press the
For HDD/DVD-RAM/-RW/-R Disc
1
During play, press the SEARCH (
the remote control.
■
NOTE
No sound is heard during Scan(Search)
mode, except CDs (CD-DA).
4-00819S-XSA_44-58_Play
6/9/05
2:06 PM
Page 47
Skipping Chapters, a Tracks or
Markers
During play, you can search quickly through a chapter
or track.
Slow Motion Play/
Step Motion Play
Slow Motion Play
1
During play, press the SKIP (
remote control.
) buttons on the
• If you press the SKIP ( ) button,
it moves to the beginning of the chapter or track or
marker(HDD/DVD-RAM/-RW(VR mode)).
Pressing the button once again within 3 seconds
returns to the beginning of the previous chapter or
track or marker(HDD/DVD-RAM/-RW(VR mode)).
• If you press the SKIP (
) button,
it moves to the next chapter or track or marker
(HDD/DVD-RAM/-RW(VR mode)).
In pause or step mode, press the SEARCH (
the remote control.
• If you press the SEARCH (
Slow 1/8 ➞
)button,
Slow 1/4 ➞
• If you press the SEARCH (
) buttons on
Slow 1/2
) button,
Slow 1/8 ➞
Slow 1/4 ➞
Slow 1/2
• To return to normal speed playback, press the
PLAY (
) button.
Press and hold the SEARCH (
) buttons during
pause, the disc will play slowly at a 1/4 speed. If the
button is released, the pause operation will resume.
■
The speed marked in this function may be
different from the actual playback speed.
Slow motion operates only in the forward
direction on MPEG4 discs.
English - 47
Playback
■
NOTE
4-00819S-XSA_44-58_Play
6/9/05
2:06 PM
Page 48
Step Motion Play
Press the STEP(
in the pause mode.
) buttons on the remote control
• Each time the button is pressed, a new frame will
appear.
When the STEP(
About ANYKEY
) button is pressed, the previous
The ANYKEY function allows you to easily search for
a desired scene by accessing title, chapter, track,
time. You can also change the subtitle and audio
settings and set some features including Marker,
Angle, Zoom, Repeat, Select Media, Disc Manager.
frame will be activated.
When the STEP(
) button is pressed, the next
Moving to a scene directly using the
ANYKEY
frame will be activated.
• To return to normal speed playback, press the PLAY
) button.
(
■
NOTE
• If you want to move to a title, a chapter or a
track to find a desired scene.
Step motion operates only in the forward
direction on MPEG4 discs.
Playback
1
Press the ANYKEY button during playback.
Search
√
Navigation
Marker
Subtitle
√
Audio
√
Repeat
√
Zoom
√
Select Media
Disc Manager
2
Press the …† buttons to select Search, then
press the OK or √ button.
HDD
Title
1/10
Time
00:01:45
MOVE
CHANGE
DVD-Video
Title
1/10
Chapter
1/40
Time
MOVE
48 - English
00:01:45
CHANGE
4-00819S-XSA_44-58_Play
6/9/05
2:06 PM
Page 49
■
3
Press the …† buttons to select Title, Chapter
or Track.
4
Press the œ √ buttons or number buttons to
select the desired scene, then press the OK
button.
NOTE
■
■
This may not work for some discs. When
an audio CD(CD-DA) or an MP3 disc is
inserted, according to a disc type, the
information display may not be appear.
The Time Search function does not
operate in some discs.
To make the screen disappear, press the
ANYKEY button again
• If you want to move to a desired time following will
help you find a scene.
1
Press the ANYKEY button during playback.
Search
√
Navigation
Marker
Subtitle
√
Audio
√
Repeat
√
Zoom
√
Select Media
Disc Manager
Playback
2
Press the …† buttons to select Search, then
press the OK or √ button.
HDD
Title
1/10
Time
00:01:45
MOVE
CHANGE
DVD-Video
Title
1/10
Chapter
1/40
Time
MOVE
00:01:45
CHANGE
3
Press the …† buttons to select Time.
4
Enter the time in the sequence of hours, minutes,
and seconds using the number buttons, then
press the OK button.
English - 49
4-00819S-XSA_44-58_Play
6/9/05
2:06 PM
Page 50
Playing the Title List
2
Press the …† buttons to select an entry you
want to play from Title List, then press the OK
or PLAY ( ) button.
The selected entry (title) will be played back.
- About INFO button If you press the INFO button during a playback,
Pressing the INFO button once, the system information
screen appears.: Displays Active Status, Background
Status, and Main Screen information.
Follow these instructions to play back a scene from the
Title List.
HDD
Active status
Background Status
Screen
01/JAN/2005 (SAT)
Using the TITLE LIST button
1
12:00
With the unit in Stop mode/Playback mode, press the
TITLE LIST button.
The Title List screen is displayed.
Pressing the INFO button twice, Disc information screen
appears.: Displays Total numbers of Titles and Playlists,
Recordable Time(Title), Available Space(Music/Photo).
Title List
HDD
No.
001
002
003
004
Title
18/JAN/2005 12:15P
19/JAN/2005 12:15P
20/JAN/2005 12:15P
25/JAN/2005 12:15P
Length
00:10:21
00:40:03
00:20:15
00:50:16
HDD
Total Title
Total Playlist
Recordable Time:Title
Available Space:Music/Photo
01/JAN/2005 (SAT)
18/JAN/2005 12:15 PR 7
18/JAN/2005 12:15
Playback
System Info
Play
––
Playback
SP
V-Mode Compatibility
MOVE
1/1 page
SELECT
RETURN
EXIT
Disc Info
15
2
31:46 SP
10033 MB
12:00
Using the MENU button.
• With the unit in Stop mode/Playback mode,
press the MENU button.
Pressing the INFO button three times, Current playback
information screen appears.: Displays information of
Playback Name, Title, Created Time, Length, Playing
Time, Audio, and if the disc protection is activated.
Title
HDD
√
Title List
Title
Music
HDD
Name
Playing Info
01/JAN/2005 12:39 PR
3
Title
1/15
Created Time
01/JAN/2005 12:00
Length
00:01:43 SP
Playing Time
00:13:27
Audio
Dolby Digital 2/0 L+R
Title Protection
Not Protected
01/JAN/2005 (SAT)
12:00
Photo
Programme
Setup
MOVE
SELECT
RETURN
EXIT
• Press the …† buttons to select Title, then
press the OK or √ button twice.
3
50 - English
To stop title play, press the STOP( ) button.
To return the title list screen, press the TITLE
LIST button.
4-00819S-XSA_44-58_Play
6/9/05
2:06 PM
Page 51
2
Navigation Menu
Press the …† buttons to select an entry you
want to play from Title List, then press the
ANYKEY button.
Title List
Scene Navigation
HDD
Rename
No.
Protection
001
002
003
004
Copy
Delete
If there is a title composed of markers (See page 54), you
can search the desired scene using the Scene Navigation.
Edit
√
Playlist
√
19/JAN/2005 12:15PR 7
Using the TITLE LIST button
3
Length
18/JAN/2005 12:15P
19/JAN/2005 12:15P
20/JAN/2005 12:15P
25/JAN/2005 12:15P
√
Navigation
19/JAN/2005 12:15
√
Select Media
SP V-Mode Compatibility
Disc Manager
MOVE
(VR mode)
Title
00:10:21
00:40:03
00:20:15
00:50:16
1/1 page
SELECT
RETURN
EXIT
Press the …† buttons to select Navigation,
then press the OK or √ button.
Title List
1
With the unit in Stop mode/Playback mode, press the
TITLE LIST button.
The Title List screen is displayed.
HDD
Rename
No.
Protection
001
002
003
004
Copy
Delete
Edit
√
Playlist
√
19/JAN/2005 12:15 PR 7
No.
18/JAN/2005 12:15P
19/JAN/2005 12:15P
20/JAN/2005 12:15P
25/JAN/2005 12:15P
00:10:21
00:40:03
00:20:15
00:50:16
Length
MOVE
00:10:21
00:40:03
00:20:15
00:50:16
SELECT
RETURN
EXIT
18/JAN/2005 12:15 PR 7
18/JAN/2005 12:15
SP
V-Mode Compatibility
MOVE
1/1 page
SELECT
RETURN
EXIT
4
Press the …† buttons to select Scene
Navigation, then press the OK or √ button.
Scene Navigation
Using the MENU button.
HDD
• With the unit in Stop mode/Playback mode,
press the MENU button.
Title List No. 1
01 00:00:16 01 00:05:16
Title
1/1 Page
HDD
MOVE
√
Title List
Title
SELECT
RETURN
EXIT
Music
Photo
Programme
Setup
MOVE
SELECT
RETURN
EXIT
5
Press the …† œ √ buttons to select desired
scene, then press the OK or PLAY ( ) button.
• Press the …† buttons to select Title,
then press the OK or √ button twice.
English - 51
Playback
001
002
003
004
Title
Length
18/JAN/2005 12:15P
19/JAN/2005 12:15P
20/JAN/2005 12:15P
25/JAN/2005 12:15P
√ Scene Navigation
Navigation
19/JAN/2005 12:15
√ Time Navigation
Select Media
SP V-Mode Compatibility
1/1 page
Disc Manager
Title List
HDD
Title
4-00819S-XSA_44-58_Play
6/9/05
2:06 PM
Page 52
Time Navigation
Using the ANYKEY button
(VR mode)
1
Press the ANYKEY button during playback.
Using this function, you can search scene minute-byminute from the recorded title list.
Using the TITLE LIST button
Search
√
Navigation
Marker
Subtitle
√
Audio
√
Repeat
√
Zoom
Select Media
1
√
Disc Manager
With the unit in Stop mode/Playback mode, press the
TITLE LIST button.
The Title List screen is displayed.
Title List
2
HDD
Press the …† buttons to select Navigation,
then press the OK or √ button.
No.
001
002
003
004
Title
18/JAN/2005 12:15P
19/JAN/2005 12:15P
20/JAN/2005 12:15P
25/JAN/2005 12:15P
Length
00:10:21
00:40:03
00:20:15
00:50:16
18/JAN/2005 12:15 PR 7
18/JAN/2005 12:15
SP
V-Mode Compatibility
1/1 page
Search
√
Navigation
Scene Navigation
Playback
Marker
MOVE
SELECT
RETURN
EXIT
Time Navigation
Subtitle
√
Audio
√
Repeat
√
Zoom
Select Media
Using the MENU button.
√
Disc Manager
• With the unit in Stop mode/Playback mode,
press the MENU button.
3
Press the …† buttons to select Scene
Navigation, then press the OK or √ button.
Title
HDD
Scene Navigation
HDD
Title List No. 1
√
Title List
Title
Music
Photo
Programme
Setup
01 00:00:16 01 00:05:16
MOVE
1/1 Page
MOVE
4
RETURN
EXIT
Press the …† œ √ buttons to select desired
scene, then press the OK or PLAY ( ) button.
■
NOTE
SELECT
Scene Navigation will not operate if a
selected title does not have Markers.
52 - English
SELECT
RETURN
EXIT
• Press the …† buttons to select Title,
then press the OK or √ button twice.
4-00819S-XSA_44-58_Play
2
6/9/05
2:06 PM
Page 53
Press the …† buttons to select an entry you
want to play from Title List, then press the
ANYKEY button.
1
Title List
HDD
Rename
No.
Protection
001
002
003
004
Copy
Delete
Edit
√
Playlist
√
Navigation
√
19/JAN/2005 12:15PR 7
19/JAN/2005 12:15
Title
Length
18/JAN/2005 12:15P
19/JAN/2005 12:15P
20/JAN/2005 12:15P
25/JAN/2005 12:15P
Using the ANYKEY button
Press the ANYKEY button during playback.
00:10:21
00:40:03
00:20:15
00:50:16
Search
√
Navigation
Marker
√
Select Media
SP V-Mode Compatibility
Disc Manager
1/1 page
Subtitle
√
Audio
√
Repeat
√
Zoom
MOVE
SELECT
RETURN
EXIT
Select Media
√
Disc Manager
3
Press the …† buttons to select Navigation,
then press the OK or √ button.
2
Press the …† buttons to select Navigation,
then press the OK or √ button.
Title List
HDD
Rename
No.
Protection
001
002
003
004
Copy
Delete
Edit
√
Playlist
√
19/JAN/2005 12:15PR 7
Title
Search
Length
18/JAN/2005 12:15P
19/JAN/2005 12:15P
20/JAN/2005 12:15P
25/JAN/2005 12:15P
Marker
√
Audio
√
Repeat
√
Select Media
√
Disc Manager
RETURN
EXIT
Press the …† buttons to select Time
Navigation, then press the OK or √ button.
3
Press the …† buttons to select Time
Navigation, then press the OK or √ button.
Time Navigation
HDD
Time Navigation
HDD
12:15
√
12:15
œ√
12:15
12:25
CHANGE
SELECT
RETURN
EXIT
√
12:15
œ√
12:25
CHANGE
SELECT
RETURN
EXIT
4
5
Press the œ √ buttons to skip one minute at a
time and search the desired scene, then press
the OK or PLAY ( ) button.
Press the œ √ buttons to skip one minute at a
time and search the desired scene, then press
the OK or PLAY ( ) button.
■
NOTE
■
■
Cursor does not move if selected recorded
title is shorter than 1 minute.
A disc that has not been recorded by this
device may not operates Navigation
function.
An edited title may not display exact
search time.
English - 53
Playback
4
SELECT
Scene Navigation
Time Navigation
Subtitle
Zoom
√ Scene Navigation
Navigation
19/JAN/2005 12:15
√ Time Navigation
Select Media
SP V-Mode Compatibility
1/1 page
Disc Manager
MOVE
√
Navigation
00:10:21
00:40:03
00:20:15
00:50:16
4-00819S-XSA_44-58_Play
6/9/05
2:06 PM
Page 54
Using the Markers
2
Press the OK button when the desired scene appears.
• The number 01 is displayed and the scene is memorized.
Marker
01 -- -- -- -- -- -- -- -- --
N:1
(VR mode)
MOVE
√ PLAY
CANCEL
RETURN
Using the MARKER button
1
Press the MARKER button during playback.
Marker
-- -- -- -- -- -- -- -- -- --
SELECT
N:0
3
Press the œ √ buttons to move to the next position.
4
Press the OK button again when the desired scene
appears.
• The number 02 is displayed and the scene is
memorized.
RETURN
Playback
Marker
01 02 -- -- -- -- -- -- -- --
N:2
Using the ANYKEY button.
• Press the ANYKEY button during playback.
MOVE
√ PLAY
CANCEL
RETURN
Search
Navigation
√
Marker
Subtitle
√
Audio
√
Repeat
√
Zoom
Select Media
√
Disc Manager
• Press the …† buttons to select Marker,
then press the OK or √ button.
54 - English
• HDD, DVD-RAM or DVD-RW (VR Mode) discs have
the Marker function instead of the Bookmark function.
The Marker function allows you to mark up to 99
scenes. Since the scenes may be displayed as many
different pages, numbering is necessary. If a disc in
use is encoded with Disc Protection, Markers cannot
be set or deleted. Only playback is available.
4-00819S-XSA_44-58_Play
6/9/05
2:06 PM
Page 55
Playing back a marker
Clearing a marker
Using the MARKER button
1
Press the MARKER button during playback.
Marker
MOVE
01 02 -- -- -- -- -- -- -- --
√ PLAY
CANCEL
Using the MARKER button
1
N:2
01 02 03 04 05 06 07 08 09 10 √ N:10
Marker
RETURN
MOVE
√ PLAY
RETURN
Using the ANYKEY button.
• Press the ANYKEY button during playback.
• Press the ANYKEY button during playback.
Search
√
Navigation
√
Navigation
Marker
Marker
Subtitle
√
Subtitle
√
Audio
√
Audio
√
Repeat
√
Repeat
√
Zoom
√
Select Media
Disc Manager
• Press the …† buttons to select Marker,
then press the OK or √ button.
Press the œ √ buttons to select a marked scene.
Marker
01 02 -- -- -- -- -- -- -- --
• Press the …† buttons to select Marker,
then press the OK or √ button.
2
Press the œ √ buttons to select a marked scene.
Press the CANCEL button to delete the selected
mark.
N:2
Marker
MOVE
√
Select Media
Disc Manager
Playback
Zoom
√ PLAY
CANCEL
Press the OK or PLAY ( ) button to start
playing from the selected scene.
• If you press the SKIP ( ) button, it moves to
the beginning of the marker. Pressing the button
once again within 3 seconds returns to the
beginning of the previous marker.
• If you press the SKIP (
the next marker.
01 02 03 04 05 06 07 08 09 10 √ N:10
RETURN
MOVE
3
CANCEL
Using the ANYKEY button.
Search
2
Press the MARKER button during playback.
√ PLAY
Marker
MOVE
CANCEL
01 02 03 04 05 06 07 08 09 --
√ PLAY
CANCEL
RETURN
N:9
RETURN
) button, it moves to
English - 55
4-00819S-XSA_44-58_Play
■
6/9/05
2:06 PM
Page 56
When a marker is cleared while HDD/DVDRAM/-RW (VR mode) is playing, marker
numbers will change. For example, if the 7th
marker is cleared after ten markers are
registered, the marker numbers after the
eighth will automatically move ahead by one
and the 8th marker becomes the 7th.
2
Press the OK button when the desired scene
appears.
• The number 1 is displayed and the scene is
memorized.
Bookmark 1 - - - - - - - - --
Using the Bookmarks
MOVE
(V-mode)
Playback
CANCEL
RETURN
3
Press the œ √ buttons to move to the next
position.
4
Press the OK button again when the desired
scene appears.
The number 2 is displayed and the scene is
memorized.
Using the MARKER button
1
√ PLAY
Press the MARKER button during playback.
Bookmark 1 2 - - - - - - - --
Bookmark - - - - - - - - - --
MOVE
MOVE
SELECT
√ PLAY
CANCEL
RETURN
RETURN
• Repeat above to bookmark other positions.
• You can bookmark up to 10 scenes.
Using the ANYKEY button.
• Press the ANYKEY button during playback.
■
Search
Bookmark
Audio
√
Subtitle
√
Angle
√
Repeat
√
Zoom
Select Media
√
• Press the …† buttons to select Bookmark, then
press the OK or √ button.
56 - English
NOTE
When the disc tray is opened and then
closed, bookmarks will disappear.
4-00819S-XSA_44-58_Play
6/9/05
2:06 PM
Page 57
Playing back a bookmark
Clearing a bookmark
Using the MARKER button
1
Press the MARKER button during playback.
Using the MARKER button
1
Bookmark 1 2 - - - - - - - --
MOVE
√ PLAY
CANCEL
Press the MARKER button during playback.
Bookmark 1 2 - - - - - - - --
RETURN
MOVE
√ PLAY
CANCEL
RETURN
Using the ANYKEY button.
Using the ANYKEY button.
• Press the ANYKEY button during playback.
• Press the ANYKEY button during playback.
Search
Search
Bookmark
Bookmark
√
Audio
√
Subtitle
√
Subtitle
√
Angle
√
Angle
√
Repeat
√
Repeat
√
Zoom
Select Media
Playback
Audio
Zoom
√
Select Media
• Press the …† buttons to select Bookmark, then
press the OK or √ button.
2
Press the œ √ buttons to select a bookmarked
scene.
3
Press the OK or PLAY(
from the selected scene.
√
• Press the …† buttons to select Bookmark, then
press the OK or √ button.
2
) button to start playing
Press the œ √ buttons to select a bookmarked
scene.
Bookmark 1 2 - - - - - - - --
MOVE
3
√ PLAY
CANCEL
RETURN
Press the CANCEL button to delete the selected
bookmark.
English - 57
4-00819S-XSA_44-58_Play
6/9/05
2:06 PM
Page 58
Selecting the Subtitle
Language
Using the ANYKEY button
1
Press the ANYKEY button during playback.
Selects one of the subtitle language recorded on the
disc.
Search
Navigation
√
Marker
Subtitle
√
Audio
√
Repeat
√
Zoom
Select Media
(VR mode)
√
Disc Manager
Using the SUBTITLE button
1
Press the SUBTITLE button during playback.
Subtitle
2
Press the …† buttons to select Subtitle, then
press the OK or √ button.
Search
Off
Navigation
√
Marker
Subtitle
√
Off
Audio
√
KOR
Repeat
√
CHI
ENG
Playback
Zoom
Select Media
√
Disc Manager
2
Press the …† buttons to select the desired
subtitle language. Also, press the SUBTITLE
button repeatedly to select the desired subtitle
language.
• To make the screen disappear, press the
CANCEL or RETURN button.
3
Press the …† buttons to select the desired subtitle
language, then press the OK or √ button.
■
NOTE
■
58 - English
The subtitle display may be different
depending on the disc type.
Some discs allow you to select the
language for the disc menu only.
5-00819S-XSA_59-74_Play
6/9/05
2:46 PM
Page 59
Selecting the Soundtracks
& Audio Channels
Using the ANYKEY button
1
Press the ANYKEY button during playback.
Selecting the Audio
Search
Navigation
Selects one of the soundtracks recorded on the disc.
Also selects the audio channels.
√
Marker
Subtitle
√
Audio
√
Repeat
√
Zoom
Select Media
√
Disc Manager
(VR mode)
Using the AUDIO button
1
Press the AUDIO button during playback.
2
Press the …† buttons to select Audio, then
press the OK or √ button.
HDD/DVD-RAM/-RW
Search
Navigation
Audio
√
Marker
Dolby Digital 2/0 L + R
Subtitle
√
Audio
√
Dolby Digital 2/0 L + R
Repeat
√
Dolby Digital 2/0 L
Select Media
Playback
Dolby Digital 2/0 R
Zoom
√
Disc Manager
DVD-VIDEO
Audio
3
ENG Dolby Digital 5.1CH
Press the …† buttons to select the desired
soundtracks or audio channel, then press the
OK or √ button.
■
NOTE
■
2
Soundtracks or Audio channel may be
different because they are disc-specific.
Some discs allow you to select the audio
language for the disc menu only.
Press the …† buttons to select the desired
soundtracks or audio channel. Also, press the
AUDIO button repeatedly to select the desired
soundtracks or audio channel.
• To make the screen disappear, then press the
CANCEL or RETURN button.
English - 59
5-00819S-XSA_59-74_Play
6/9/05
2:46 PM
Page 60
Changing the Camera
Angle
Repeat Play
When a HDD & DVD RECORDER contains multiple
angles of a particular scene, you can select the Angle
function.
Playing Repeatedly(Repeat Playback)
Using the REPEAT button
Using the ANYKEY button
1
1
Press the REPEAT button during playback.
Press the ANYKEY button during playback.
Repeat
Off
Search
Bookmark
Audio
√
Subtitle
√
Angle
√
Repeat
√
Zoom
Playback
Select Media
2
√
Press the …† buttons to select Angle, then
press the OK or √ button.
Bookmark
Audio
√
Angle 1
Subtitle
√
Angle 2
Angle
√
Angle 3
Repeat
√
Angle 4
Angle 5
Zoom
3
√
Angle 6
Press the …† buttons to select the desired angle,
then press the OK or √ button.
■
NOTE
■
This function is disc-dependent, and may
not work all DVDs.
This function does not work when a DVD
has not been recorded with a multicamera angle system.
60 - English
Press the …† buttons to select the Off, Title or
Chapter you want to play repeatedly, then
press the OK button.
Repeat
Search
Select Media
2
Title
5-00819S-XSA_59-74_Play
6/9/05
2:46 PM
Page 61
Repeat A-B
Using the ANYKEY button
1
Press the ANYKEY button during playback.
Using the REPEAT A-B button
Search
Navigation
1
√
Marker
Subtitle
√
Audio
√
Repeat
√
Repeat A-B
Zoom
Select Media
Press the REPEAT A-B button during playback.
Off
√
Disc Manager
2
Press the …† buttons to select the Repeat,
then press the OK or √ button.
2
Search
Navigation
√
Marker
Subtitle
√
Audio
√
Repeat
√
Repeat Off
Repeat A - B
Zoom
√
Repeat Title
Disc Manager
3
Repeat A-B
A-B
Press the …† buttons to select Repeat Off,
Repeat A-B, Repeat Title, Repeat Track or
Repeat Chapter you want to play repeatedly, then
press the OK or √ button.
■
NOTE
Playback
Select Media
Press the OK button at the point where you want the
repeat play to start (A) and press it again at the point
where you want the repeat play to stop (B). Repeat
playback of the A-B section starts.
HDD/DVD-RAM/-RW(VR mode), unfinalised
DVD-R and unfinalised DVD-RW (V mode)
do not repeat a chapter.
English - 61
5-00819S-XSA_59-74_Play
6/9/05
2:46 PM
Page 62
Using the ANYKEY button
1
Zooming-In
Press the ANYKEY button during playback.
Search
Navigation
√
Marker
Subtitle
√
Audio
√
Repeat
√
1
Zoom
Select Media
√
Press the ANYKEY button during playback.
Disc Manager
Search
Navigation
√
Marker
2
Press the …† buttons to select Repeat, then
press the OK or √ button.
Subtitle
√
Audio
√
Repeat
√
Zoom
Select Media
√
Disc Manager
Search
Navigation
√
Marker
Subtitle
√
Audio
√
Repeat
√
Select Media
Repeat Off
Repeat A - B
Zoom
√
Repeat Title
2
Press the …† buttons to select Zoom, then press
the OK or √ button. ( ) will be displayed.
3
Press …† œ √ buttons to move to the area you
want to enlarge.
4
Press the OK button.
The screen will be enlarged to twice the normal
size. The screen size will be enlarged to four times
the normal size.
Playback
Disc Manager
3
Press the …† buttons to select Repeat A-B,
then press the OK or √ button.
4
Press the OK button at the point where you
want the repeat play to start (A) and press it
again at the point where you want the repeat
play to stop (B).Repeat playback of the A-B
section starts.
- To return to normal playback -
5
Press the CANCEL button to return to normal
playback.
■
NOTE
■
■
If you set point (B) before five seconds
has lapsed, the prohibition mark ( ) will
appear.
You can also activate Normal Playback by
pressing the CANCEL button.
Audio CDs(CD-DA), MP3 discs and
MPEG4 discs do not support the Repeat
A-B function.
62 - English
HDD/DVD-VIDEO/
DVD-RAM/-RW/-R
■
NOTE
normal size ➞ X2 ➞ X4
➞ X2 ➞ normal size
When recording is done in the EP mode, the
Zoom function will not be supported except
when the recording has been done in V
mode.
5-00819S-XSA_59-74_Play
6/9/05
2:46 PM
Page 63
Select Media
Playing an Audio
CD/MP3
Playing an Audio CD(CD-DA)
1
Press the ANYKEY button during playback.
1
Insert an audio CD (CD-DA) into the disc tray.
• The audio CD menu appears and the tracks
(songs) are played automatically.
Search
Navigation
√
Marker
Subtitle
√
Audio
√
Repeat
√
Music List
CD
TRACK 1
Zoom
Select Media
√ 02 : 10
TRACK 1
√
Disc Manager
CD-DA
01/15
04:57
CDDA
TRACK 2
CDDA
TRACK 3
CDDA
TRACK 4
CDDA
TRACK 5
CDDA
TRACK 6
CDDA
TRACK 7
1/3 Page
2
Press the …† buttons to select Select Media,
then press the OK or √ button.
MOVE
Search
2
√
Marker
Subtitle
√
Audio
√
Repeat
√
RETURN
EXIT
Press the …† buttons to select the track (song)
you want to hear, and then press the OK button.
Zoom
Select Media
Disc Manager
3
√
HDD
DVD
Audio CD(CD-DA) Screen Elements
!
Press the …† buttons to select HDD or DVD,
then press the OK or √ button.
Music List
CD
√ 02 : 10
TRACK 1
$
TRACK 1
@
CD-DA
01/15
04:57
CDDA
TRACK 2
CDDA
TRACK 3
CDDA
TRACK 4
CDDA
TRACK 5
CDDA
TRACK 6
CDDA
TRACK 7
%
1/3 Page
#
MOVE
SELECT
RETURN
EXIT
1. Current track (song): Displays the number of the
track currently being played.
2. Displays the current play index, total track number.
3. Display available buttons.
4. This shows the operating state of a disc and a
playback time corresponding to a portion that is
currently played.
5. Displays the track list (song list).
English - 63
Playback
Navigation
SELECT
5-00819S-XSA_59-74_Play
6/9/05
2:46 PM
Page 64
Buttons on the Remote Control
used for Audio CD(CD-DA) playback
DVD
TV
Playing an MP3 Disc
Insert an MP3 disc into the disc tray.
• The MP3 menu is displayed and the tracks
(songs) are played automatically.
1
Music List
Bryan Adams.mp3 √ 02 : 10
CD
..
Bryan Adams.mp3
MP3
01/15
4.0 MB
MP3
Bryan Adams_2.mp3
MP3
Straight from the heart.mp3
MP3
Run to you.mp3
MP3
Heaven.mp3
MP3
This Love.mp3
1/3 Page
MOVE
SELECT
RETURN
EXIT
Press the …† buttons to select the track you want to
hear, and then press the OK button.
2
Playback
MP3 Screen Elements
!
Music List
Bryan Adams.mp3 √ 02 : 10
CD
$
..
Bryan Adams.mp3
MP3
01/15
4.0 MB
@
1. …†: Selects a track (song).
2. œ √ : Move the page up/down.
3. OK button: Plays the selected track (song).
4. SKIP ( ) button: Plays the next track.
5. SKIP ( ) button: Returns to the beginning of the
current track when pressed during playback. If
pressed again, your HDD & DVD RECORDER
moves to and plays the previous track.
If you press the this button within three seconds after
playback starts, the previous track will be played.
If you press the this button after three seconds, the
current track will be replayed from the beginning.
6. Press the SEARCH (
) buttons:
Fast Play (X2, X4, X8)
7. STOP ( ) button: Stops a track(song).
8. PLAY ( ) button: Plays a track(song) or pauses
playback.
9. ANYKEY button: The ANYKEY menu is displayed.
(Play Mode, Go To Playlist or New Playlist).
64 - English
MP3
Bryan Adams_2.mp3
MP3
Straight from the heart.mp3
MP3
Run to you.mp3
MP3
Heaven.mp3
MP3
This Love.mp3
%
1/3 Page
#
MOVE
SELECT
RETURN
EXIT
1. Current track (song): Displays the name of the
track being played.
2. Displays the current folder, play index and current
track size.
3. Displays available buttons.
4. This shows the operating state of a disc and a
playback time corresponding to a portion that is
currently played.
5. Displays the information for the folder and its tracks.
■
NOTE
■
If a disc contains only MP3 files or only
JPEG files, the MP3 or JPEG screen
appears after the disc is loaded.
If a disc contains a mix of MP3 and JPEG
files, you need to select Music for MP3
files or Photo for JPEG files.
5-00819S-XSA_59-74_Play
6/9/05
2:46 PM
Page 65
Buttons on the Remote Control
used for MP3 playback
DVD
Repeat CD (CD-DA) & MP3
Using the REPEAT button.
TV
1
Press the REPEAT button during playback.
Music List
CD
√ 02 : 10
TRACK 1
TRACK 1
CD-DA
01/15
04:57
CDDA
TRACK 2
CDDA
TRACK 3
CDDA
TRACK 4
CDDA
TRACK 5
CDDA
TRACK 6
CDDA
TRACK 7
1/3 Page
MOVE
2
SELECT
RETURN
EXIT
Press the REPEAT button repeatedly to select the repeat
mode you want.
Music List
CD
√ 02 : 10
TRACK 1
TRACK 1
TRACK 2
CDDA
TRACK 3
CDDA
TRACK 4
CDDA
TRACK 5
CDDA
TRACK 6
CDDA
TRACK 7
1/3 Page
MOVE
1. …†: Selects a track (song).
2. œ √ : Move the page up/down.
3. OK button: Plays the selected track (song).
4. SKIP ( ) button: Plays the next track.
5. SKIP ( ) button: Returns to the beginning of the
current track when pressed during playback. If
pressed again, your HDD & DVD RECORDER
moves to and plays the previous track.
If you press the this button within three seconds after
playback starts, the previous track will be played.
If you press the this button after three seconds, the
current track will be replayed from the beginning.
6. STOP ( ) button: Stops a track(song).
7. PLAY ( ) button: Plays a track(song) or pauses
playback.
8. ANYKEY button: The ANYKEY menu is displayed.
(Copy, Play Mode, Go To Playlist, New Playlist or
Select Media).
SELECT
RETURN
EXIT
Repeat Track (CD (CD-DA)/MP3)
Repeat Folder (MP3)
Repeat All (CD (CD-DA)/MP3)
Random (CD (CD-DA)/MP3): The random option
plays a disc’s track in random order.
• Normal (CD (CD-DA)/MP3): Track on a disc are
played in the order in which they were recorded on the
disc.
•
•
•
•
- To return to normal playback -
3
Press the REPEAT or CANCEL button repeatedly
to return to normal playback.
English - 65
Playback
CD-DA
01/15
04:57
CDDA
5-00819S-XSA_59-74_Play
6/9/05
2:46 PM
Page 66
New Playlist
Using the ANYKEY button
1
Press the ANYKEY button during the Music List
playback.
You can register a maximum 28 tracks in the playlist.
1
Press the ANYKEY button during the Music List
playback.
Music List
CD
» 02 : 10
TRACK 1
Music List
TRACK 1
CDDA
CD-DA
Play Mode
01/15
Go To Playlist
04:57
√
CDDA
TRACK 3
CDDA
TRACK 4
CDDA
TRACK 5
CDDA
CDDA
CD
TRACK 1
TRACK 6
CD-DA
Play Mode
01/15
Go To Playlist
04:57
TRACK 7
New Playlist
1/3 Page
MOVE
SELECT
RETURN
√
CDDA
TRACK 2
CDDA
TRACK 3
CDDA
TRACK 4
CDDA
TRACK 5
CDDA
TRACK 6
CDDA
TRACK 7
New Playlist
EXIT
1/3 Page
MOVE
2
» 02 : 10
TRACK 1
TRACK 2
Press the …† buttons to select Play Mode,
then press the OK or √ button.
2
SELECT
RETURN
EXIT
Press the …† buttons to select New Playlist,
then press the OK or √ button.
Music List
CD
» 02 : 10
TRACK 1
TRACK 1
CDDA
TRACK 2
CDDA
TRACK 3
CDDA
CD-DA
01/15
Go To Playlist
04:57
Play Mode
Playback
New Playlist
MOVE
TRACK 4
Normal
CDDA
TRACK
√
Make Playlist
CD
5
Repeat
Track6
CDDA
TRACK
CDDA
Repeat
All
TRACK
7
Random 1/3 Page
SELECT
RETURN
EXIT
CDDA
TRACK 1
CDDA
TRACK 2
CDDA
TRACK 3
CDDA
TRACK 4
CDDA
TRACK 5
CDDA
TRACK 6
CDDA
TRACK 7
1/3 Page
MOVE
3
Press the …† buttons to select desired play mode,
then press the OK or √ button.
• Normal (CD (CD-DA)/MP3): Track on a disc are
played in the order in which they were recorded on the
disc.
•
Repeat Track (CD (CD-DA)/MP3)
•
Repeat Folder (MP3)
•
Repeat All (CD (CD-DA)/MP3)
•
Random (CD (CD-DA)/MP3): The random option
plays a disc’s track in random order.
3
Add
EXIT
Press the …† buttons to select tracks in order in
which you want them to play, then press the OK
button.
Make Playlist
CD
CDDA
TRACK 1
01.
CDDA
TRACK 2
02.
TRACK 3
CDDA
TRACK 3
03.
TRACK 7
CDDA
TRACK 4
04.
TRACK 4
CDDA
TRACK 5
CDDA
TRACK 6
CDDA
TRACK 7
TRACK 1
1/1 Page
1/3 Page
MOVE
66 - English
RETURN
Add
RETURN
EXIT
5-00819S-XSA_59-74_Play
6/9/05
2:46 PM
Page 67
Go To Playlist
4
If you playlisted a wrong track, press the √…†
buttons to select wrong track, then press the
OK or CANCEL button. The wrong track will be
removed.
1
Press the ANYKEY button during the Music List
playback.
Make Playlist
CD
CDDA
TRACK 1
01.
TRACK 1
CDDA
TRACK 2
02.
TRACK 3
CDDA
TRACK 3
03.
TRACK 7
CDDA
TRACK 4
CDDA
TRACK 2
CDDA
TRACK 5
CDDA
TRACK 3
CDDA
TRACK 6
CDDA
TRACK 4
CDDA
TRACK 7
CDDA
TRACK 5
CDDA
TRACK 6
CDDA
TRACK 7
Delete
CD-DA
01/15
Go To Playlist
04:57
Play Mode
EXIT
√
New Playlist
MOVE
5
» 02 : 10
TRACK 1
TRACK 1
1/1 Page
1/3 Page
MOVE
Music List
CD
1/3 Page
SELECT
RETURN
EXIT
To store the Playlist, press the ANYKEY button.
Make Playlist
CD
CDDA
TRACK 1
01.
CDDA
2
TRACK 1
TRACK 2
02.
TRACK 3
CDDA
TRACK 3
03.
TRACK 7
CDDA
TRACK 4
CDDA
TRACK 5
Playlist
CD
TRACK 6
Delete
CDDA
TRACK 7
CDDA
00 : 00
PLAYLIST
Go To Playlist1/3 Page
MOVE
Press the …† buttons to select Go To Playlist,
then press the OK or √ button.
Playlist 1
1/1 Page
SELECT
RETURN
Playlist 2
EXIT
1/1 Page
6
Press the …† buttons to select the Go To
Playlist, then press the OK button.
A new Playlist will be created.
MOVE
SELECT
RETURN
EXIT
3
Press the …† buttons to select the desired
playlist folder, then press the OK button.
4
The selected tracks are played automatically.
English - 67
Playback
PLAYLIST
-00 : 00
5-00819S-XSA_59-74_Play
6/9/05
2:47 PM
Page 68
Delete the Playlist
1
Go To Edit Playlist
Press the ANYKEY button during the Music List
playback.
1
Press the ANYKEY button during the Music List
playback.
Music List
CD
» 02 : 10
TRACK 1
Music List
TRACK 1
CD-DA
Play Mode
01/15
Go To Playlist
04:57
√
CDDA
TRACK 2
CDDA
TRACK 3
CDDA
TRACK 4
CDDA
TRACK 5
CDDA
TRACK 6
CDDA
CD
TRACK 1
CD-DA
Play Mode
01/15
Go To Playlist
04:57
TRACK 7
New Playlist
1/3 Page
MOVE
SELECT
RETURN
√
Press the …† buttons to select Go To Playlist,
then press the OK or √ button.
Playlist
CD
00 : 00
CDDA
TRACK 2
CDDA
TRACK 3
CDDA
TRACK 4
CDDA
TRACK 5
CDDA
TRACK 6
CDDA
TRACK 7
New Playlist
EXIT
MOVE
2
» 02 : 10
TRACK 1
2
1/3 Page
SELECT
RETURN
EXIT
Press the …† buttons to select Go To Playlist,
then press the OK or √ button.
PLAYLIST
Playlist 1
Playlist 2
Playlist
CD
PLAYLIST
-00 : 00
00 : 00
PLAYLIST
Playlist 1
Playlist 2
1/1 Page
Playback
MOVE
SELECT
RETURN
EXIT
PLAYLIST
-00 : 00
1/1 Page
3
Press the …† buttons to select the Playlist you
want to delete.
4
Press the ANYKEY button.
MOVE
SELECT
RETURN
EXIT
3
Press the …† buttons to select the Playlist you
want to edit.
4
Press the ANYKEY button in playlist mode.
Playlist
CD
00 : 00
PLAYLIST
Playlist 1
Playlist 2
Delete Playlist
PLAYLIST
01/02
00 : 00
Go To Edit Playlist
Go To Music List
New Playlist
1/1 Page
MOVE
SELECT
RETURN
EXIT
Playlist
CD
00 : 00
PLAYLIST
Playlist 1
5
Press the …† buttons to select the Delete
Playlist, then press the OK or √ button.
Playlist 2
Delete Playlist
PLAYLIST
01/02
00 : 00
Go To Edit Playlist
Go To Music List
New Playlist
Playlist
CD
00 : 00
PLAYLIST
Playlist 1
Playlist 1
Playlist 2
Do you want to delete?
No
Yes
1/1 Page
MOVE
6
SELECT
RETURN
EXIT
Press the œ √ buttons to select Yes, then press
the OK button. The selected Playlist is deleted.
68 - English
MOVE
1/1 Page
SELECT
RETURN
EXIT
5-00819S-XSA_59-74_Play
6/9/05
2:47 PM
Page 69
Go To Music List
5
Press the …† buttons to select the Go To Edit
Playlist, then press the OK or √ button.
1
Edit Playlist
Press the ANYKEY button during the Playlist
playback.
CD
CDDA
TRACK 1
01
CDDA
TRACK 2
02
TRACK 1
TRACK 3
CDDA
TRACK 3
03
TRACK 7
CDDA
TRACK 4
04
TRACK 4
CDDA
TRACK 5
CDDA
TRACK 6
CDDA
TRACK 7
Playlist
CD
Playlist 1
TRACK 1
1/1 Page
1/3 Page
MOVE
Add
RETURN
PLAYLIST
01/04
Go To Music List
04 : 30
EXIT
CDDA
TRACK 2
CDDA
TRACK 3
CDDA
TRACK 4
New Playlist
MOVE
6
7
Press the …† buttons to select tracks in order in
which you want them to play, then press the OK
button.
If you playlisted a wrong track, press the √ …†
buttons to select wrong track, then press the OK
or CANCEL button.
To store the Playlist, press the ANYKEY button.
2
1/1 Page
SELECT
RETURN
EXIT
Press the …† buttons to select Go To Music List,
then press the OK or √ button.
Music List
CD
√ 02 : 10
TRACK 1
TRACK 1
CD-DA
01/15
04:57
CDDA
TRACK 2
CDDA
TRACK 3
CDDA
TRACK 4
CDDA
TRACK 5
CDDA
TRACK 6
CDDA
TRACK 7
1/3 Page
MOVE
Edit Playlist
SELECT
RETURN
EXIT
CD
CDDA
TRACK 1
01
TRACK 1
CDDA
TRACK 2
02
TRACK 3
CDDA
TRACK 3
03
TRACK 7
CDDA
TRACK 4
04
TRACK 4
CDDA
TRACK 5
05
TRACK 6
CDDA
TRACK 6
AddTRACK
CDDA
7
Go To Playlist
1/3 Page
MOVE
9
1/1 Page
SELECT
RETURN
EXIT
Press the …† buttons to select the Go To
Playlist, then press the OK button.
Playlist will be edited.
English - 69
Playback
8
» 02 : 10
TRACK 1
5-00819S-XSA_59-74_Play
6/9/05
2:47 PM
Page 70
Select Media (MP3)
1
Playing a Picture
Press the ANYKEY button.
Music List
Bryan Adams.mp3 » 02 : 10
CD
..
Bryan Adams.mp3
Copy
Play Mode
ROOT
√
Go 01/15
To Playlist
New
4.0Playlist
MB
Select Media
MP3
Bryan Adams_2.mp3
MP3
Straight from the heart.mp3
MP3
Run to you.mp3
MP3
Heaven.mp3
MP3
This Love.mp3
√
MOVE
1
Insert a JPEG disc or Mixed disc (JPEG + MP3 + DivX)
into the disc tray.
Title
CD
1/3 Page
SELECT
Title
RETURN
EXIT
Title List
√
DivX List
√
Music
Photo
Programme
2
Setup
Press the …† buttons to select Select Media, then
press the OK or √ button.
MOVE
SELECT
RETURN
EXIT
Music List
Bryan Adams.mp3 » 02 : 10
CD
..
Bryan Adams.mp3
Copy
Play Mode
Bryan Adams_2.mp3
MP3
Straight from the heart.mp3
MP3
Run to you.mp3
Go 01/15
To Playlist
MP3
Heaven.mp3
New
4.0Playlist
MB
MP3
HDD This Love.mp3
ROOT
Playback
√
MP3
Select Media
MOVE
√
DVD
SELECT
2
Press the …† buttons to select Photo, then press the
OK or √ button.
Photo List
CD
DSC01194
Index: 1/10
1/3 Page
RETURN
EXIT
..
DSC01192
DSC01189
DSC01190
DSC01191
DSC01193
DSC01194
DSC01199
1/2 Page
3
Press the …† buttons to select HDD or DVD, then
press the OK or √ button.
If there are no mp3 files on the selected media, it
notifies you that there are no mp3 files and the
media will not be switched.
MOVE
3
RETURN
EXIT
Press the …† œ √ buttons to select a picture.
• To see the next 8 pictures, press the SKIP(
button.
• To see the previous 8 pictures, press the
SKIP( ) button.
■
NOTE
■
70 - English
SELECT
)
If a disc contains only MP3 files or only
JPEG files, the MP3 or JPEG screen
appears after the disc is loaded.
If a disc contains a mix of MP3 and JPEG
files, you need to select Music for MP3
files or Photo for JPEG files.
5-00819S-XSA_59-74_Play
6/9/05
2:47 PM
Page 71
Slide Show
- To stop the Slide Show -
4
1
Press the ANYKEY button.
Press the ANYKEY button.
Photo List
CD
DSC01194
..
DSC01189
Index: 1/10
DSC01190
DSC01191
DSC01194
DSC01199
Copy
Slide Show
DSC01192
√
MOVE
5
Slideshow
√
DSC01193
Select Media
SELECT
√
Slideshow Off
1/2 Page
Go To Photo List
RETURN
EXIT
Press the …† buttons to select Slide Show,
then press the OK or √ button.
2
Press the …† buttons to select Slideshow Off,
then press the OK or √ button.
Photo List
CD
DSC01194
..
DSC01189
Slide Show
Select Media
√
DSC01193
DSC01191
√
Normal
DSC01194
Fast
DSC01199
1/2 Page
SELECT
RETURN
Playback
MOVE
6
DSC01190
Slow
Copy
DSC01192
Index: 1/10
EXIT
Press the …† buttons to select the slide show
speed, then press the OK or √ button.
The slide show starts.
English - 71
5-00819S-XSA_59-74_Play
6/9/05
2:47 PM
Page 72
Rotate
Zoom
To setup, follow steps 1 to 3 in page 70.
4
Press the OK button to select you want to see the
picture, then press the ANYKEY button.
Slideshow
√
Rotate
√
To setup, follow steps 1 to 3 in page 70.
4
Press the OK button to select you want to see the
picture, then press the ANYKEY button.
Slideshow
√
Rotate
√
Zoom
Zoom
Go To Photo List
Go To Photo List
Playback
5
6
Press the …† buttons to select Rotate, then
press the OK or √ button.
Slideshow
√
Rotate
√
5
Press the …† buttons to select Zoom, then
press the OK or √ button.
6
Each time the OK button is pressed, the picture
is enlarged up to 4x(four times the normal size).
Rotate 90
Zoom
Rotate 180
Go To Photo List
Rotate 270
Press the …† buttons to select the rotate angle,
then press the OK or √ button.
➞ X2 ➞ X4 ➞ X2 ➞ Normal
- To stop the Rotate -
1
Press the ANYKEY button.
- To stop the Zoom -
1
Rotate
Press the ANYKEY button.
√
Rotate Off
Go To Photo List
Zoom Off
Go To Photo List
2
Press the …† buttons to select Rotate Off, then
press the OK or √ button.
2
72 - English
Press the …† buttons to select Zoom Off, then
press the OK or √ button.
5-00819S-XSA_59-74_Play
6/9/05
2:47 PM
Page 73
Go To Photo List
Playing an MPEG4
To setup, follow steps 1 to 3 in page 70.
4
Press the OK button to select you want to see the
picture, then press the ANYKEY button.
Using the MENU button
Slideshow
√
Rotate
√
1
Insert a DivX disc or Mixed disc (JPEG + MP3 + DivX)
into the disc tray.
2
Press the …† buttons to select Title, then press
the OK or √ button.
(In case of playing a DivX CD, see number 4 on
this page.)
Zoom
Go To Photolist
5
Press the …† buttons to select Go To Photo
List, then press the OK or √ button.
Title
CD
Title
Photo List
CD
DSC01194
Title List
√
DivX List
√
Music
Index: 1/10
Photo
Programme
DSC01189
DSC01190
DSC01191
Setup
MOVE
DSC01192
DSC01193
DSC01194
SELECT
RETURN
EXIT
DSC01199
1/2 Page
MOVE
SELECT
RETURN
EXIT
3
Press the …† buttons to select DivX List,
then press the OK or √ button.
The DivX List screen is displayed.
DivX List
CD
ABC.avi
..
DIVX
[DivX] ABC.avi
MPEG4
01/01
703.4MB
1/1 Page
MOVE
4
SELECT
RETURN
EXIT
Press the …† buttons to select the avi file
(DivX), then press the OK or PLAY ( ) button.
English - 73
Playback
..
5-00819S-XSA_59-74_Play
5
6/9/05
2:47 PM
Page 74
When MPEG4 file is played, you can use
following functions. Pressing the STOP ( )
button once during playback will display the file
list, pressing the button again will exit the menu
screen.
DivX Subtitle Encoding
1
Press the ANYKEY button during playback.
MPEG4 Function Description
Function
Search
Description
Skip
During play, press the SKIP (
) buttons, it
moves forward or backward 5 minutes.
Search
) buttons
During play, press the SEARCH (
and press again to search at a faster speed.
(X2, X4, X8)
Slow Motion In pause or step mode, press the SEARCH ( )
Play
button on the remote control. (X1/8, X1/4, X1/2)
Audio
√
Subtitle
√
Repeat
√
Subtitle Encoding √
2
Press the …† buttons to select Subtitle
Encoding, then press the OK or √ button.
Step Motion Press the STEP (
) button on the remote
Play
control in the still mode.
Search
Playback
■
NOTE
■
■
This unit can play the following video
compression formats,
- MPEG4 Codec format : DivX 3.11 DivX
4.x DivX 5.x DivX-Pro (without QPEL and
GMC)
- Audio format : .MP3, .MPEG, .WMA,
.LPCM, .AC3
Supported subtitle file formats: .smi, .srt,
.sub, .psb, .txt, .ass (The subtitle file
should have exactly the same name to
corresponding MPEG4 file name)
Some MPEG4 files created on a personal
computer may not be play back.
That is why Codec Type, Version and
Higher resolution over specification is not
supported.
√
Subtitle
√
Central(Windows)
Repeat
√
Western(Windows)
Subtitle Encoding √
3
NOTE
Greek(Windows)
Press the …† buttons to select a supported
DivX subtitle language by region, then press the
OK or √ button.
Western
English, Breton, Catalan, Danish, Dutch,
Faroese, Finnish, French, Gaelic, German,
Icelandic, Irish, Italian, Norwegian, Portuguese,
Spanish and Swedish
Central
English, Albanian, Croatian, Czech, Hungarian,
Polish, Romanian, Slovak, Slovene and
Serbian(Latin)
Greek
English and modern Greek
■
74 - English
Audio
If the subtitle language is displayed in
broken fonts, change DivX Subtitle to the
appropriate region. If is still does not work,
the format is not supported.
6-00819S-XSA_75-92_REC
6/9/05
2:52 PM
Page 75
Recording
Before Recording
This unit can record on various types of discs. Before
recording, read the following instructions and select the
disc type according to your preference.
Recordable Discs
This section shows various HDD & DVD
Recording methods.
This recorder can record on the following discs.
HDD
DVD-RAM
DVD-RW
DVD-R
•DVD-RWs and DVD-RAMs are rewritable.
•DVD-Rs are non-rewritable
Compatibility between Samsung and Other Company’s
Recorder
Disc Types
Recording
format
DVD-RAM
VR Mode
Recording the current TV programme
you are watching . . . . . . . . . . . . . . . . . . . . . . . . . .77
VR Mode
DVD-RW
V Mode
Recording from external equipment
you are watching . . . . . . . . . . . . . . . . . . . . . . . . . .79
Copying from a Camcorder . . . . . . . . . . . . . . . . . .80
V Mode
DVD-R
Making an One Touch Recording (OTR) . . . . . . . .81
Chasing Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
■
Simultaneous Recording and Playback . . . . . . . . .83
NOTE
Making a Timer Recording . . . . . . . . . . . . . . . . . .84
Flexible Recording (for Timer recording only) . . . .86
Editing the Timer Record List . . . . . . . . . . . . . . . .86
Deleting a Timer Record List . . . . . . . . . . . . . . . . .87
Go To History List . . . . . . . . . . . . . . . . . . . . . . . . .88
Using the G-Code Feature . . . . . . . . . . . . . . . . . .91
G-Code Extended . . . . . . . . . . . . . . . . . . . . . . . . .92
■
Finalise
- This closes the DVD-RW/-R so no
additional recording can be done.
Unfinalise
- This allows additional recording on a
DVD-RW disc originally recorded on the
HDD & DVD RECORDER.
- A DVD-RW disc that has been recorded
by DAO(Disc At Once) in a PC cannot be
unfinalised.
- A DVD-RW disc that has been recorded
in Video Mode of a different maker’s
recorder cannot be unfinalised.
- A DVD-R disc cannot be unfinalised.
English - 75
Recording
Before Recording . . . . . . . . . . . . . . . . . . . . . . . . .75
Recording Device Finalising Additional Recording
in Samsung Recorder
Samsung
X
Recordable
X
Recordable
Other Company
Not
recordable
finalised
Samsung
Recordable
not finalised
Not recordable
finalised
Other Company
Recordable
not finalised
finalised
Not
recordable
Samsung
not finalised
Recordable
Not recordable
finalised
Other Company
not finalised Not recordable
finalised
Not recordable
Samsung
not finalised
Recordable
Not recordable
finalised
Other Company
not finalised Not recordable
6-00819S-XSA_75-92_REC
6/9/05
2:52 PM
Page 76
Recording Formats
When you insert an unused disc, the following message
appears. Since available functions differ depending on
the disc type, select a disc that best fits your preferences.
DVD-RAM: Use after formatting the disc.
Recording Mode
Select one of four recording modes by pressing the
REC MODE button repeatedly while the unit is in Stop
mode for the desired recording time and picture quality.
In general, picture quality improves as the recording
time decreases. In FR mode, the most suitable record
mode is adjusted automatically, according to remaining
time on the disc and length of the timer recording. This
function is selected only one mode in XP, SP, LP and
EP modes and you can use this mode for timer
recording.
Unformatted Disc
Do you want to format this disc?
Yes
No
DVD-RW: When unused DVD-RW disc is first inserted,
the message “Uninitialized Disc Do you want
to initialize this disc?” will be displayed. If you
select Yes, the disc will be formatted in VR
mode.
If you want to change the mode, refer to
Formatting a Disc on page 121.
Recording Mode
XP
(high quality mode)
SP
(standard quality mode)
Recording Times
HDD (80GB)
DVD-RAM/-RW/-R
Approx. 1 hour
Approx. 18 hours
about 8.5 Mbps
Approx. 2 hours
Approx. 34 hours
about 4.5 Mbps
LP
(long recording mode)
Approx. 65 hours
EP
(extended mode)
Approx. 96 hours
Approx. 127 hours
FR
(Flexible Recording) Approx.18~96 hours
■
Uninitialized Disc
Do you want to initialize this disc?
Yes
NOTE
Approx. 4 hours
about 2 Mbps
Approx. 6 hours/
about 1.6 Mbps
Approx. 8 hours/
about 1.2 Mbps
Approx.1~6 hours
Recording time may vary according to
specific conditions.
No
Recording
Unrecordable pictures
DVD-R: Formatting DVD is unnecessary and only Video
Mode Recording is supported.
Video with copy protection cannot be recorded on this
HDD & DVD RECORDER.
When the HDD & DVD RECORDER receives a copy
guard signal while recording, recording stops and the
following message appears on the screen.
DVD-RW(V mode)/-R
• Chapters will be created automatically when you finalise
recording on DVD-RW/-R discs in Video mode.
The chapter’s length (interval between chapters) varies
according to the recording mode.
• Simple editing (erasing titles/changing title name)
You cannot record copy protected movie.
DVD-RAM/-RW(VR mode)
• This mode allows multiple editing functions (such as
deletion of the whole title, partial deletion of a title, etc.)
• Various editing options using a created Playlist.
76 - English
Concerning Copy Control Signals
TV broadcasts that contain copy control signals may have
one of the following three signal types, Copy-Free, CopyOnce and Copy-Never. If you want to record a copy-once
type programme, use DVD-RW with CPRM in VR Mode and
DVD-RAM.
6-00819S-XSA_75-92_REC
Signal type
Media
DVD-RW(Ver.1.1)
6/9/05
2:52 PM
Page 77
Copy-Free
Copy-Once
Copy-Never
O
-
-
O*
DVD-RW(Ver.1.1)
with CPRM
VR mode
O
V mode
O
DVD-R
O
DVD-RAM(Ver.2.0)
O
-
Recording the current TV
programme you are watching
O*
Check that the disc has enough available space for the
recording. Adjust the recording mode.
Once “Copy Once” has been recorded, recording
cannot be done anymore.
- Content Protection for Recordable Media (CPRM)
CPRM is a mechanism that ties a recording to the media on
which it is recorded. It is supported by some HDD & DVD
RECORDERs, but not by many DVD players. Each blank
recordable DVD has a unique 64-bit media ID etched in the
BCA. When protected content is recorded onto the disc, it can
be encrypted with a 56-bit C2 (Cryptomeria) cipher derived
from the media ID.
1
Press the HDD or DVD button.
If you select DVD, Press the OPEN/CLOSE button and
place a recordable disc on the disc tray.
Press the OPEN/CLOSE button to close the disc tray.
Wait until LOAD disappears from the front panel display.
If an unused DVD-RAM disc is used, you will be
prompted to format first. Make your selection using the
œ √ buttons, then press OK button.(See page 76)
During playback, the ID is read from the BCA and used to
generate a key to decrypt the contents of the disc. If the
contents of the disc are copied to other media, the ID will be
absent or wrong and the data will not be decryptable.
Unformatted Disc
Do you want to format this disc?
Yes
No
Uninitialized Disc
Do you want to initialize this disc?
Yes
2
No
Press the PROG (
) or number buttons to select
the current programme you want to record.
English - 77
Recording
If an unused DVD-RW disc is used, whether to initialize
or not will be asked first. Make your selection, then press
the OK button.(See page 76)
6-00819S-XSA_75-92_REC
3
6/9/05
2:52 PM
Page 78
Press the REC MODE button repeatedly, (or press the
REC MODE button and then press the …† buttons) to
select the recording speed(quality).
➞ SP ➞ LP ➞ EP ➞ XP
■
You can not change the recording mode
and the PROG while recording.
■
Recording will stop automatically if there is
no free space left for recording.
■
Up to 99 titles can be recorded onto a
disc.(DVD-RAM/-RW/-R)
■
Up to 999 titles can be registered on the
HDD.
■
HDD recording is available for up to 24
hours, and when recording for 24 hours, 4
titles will be recorded with each title has 6
hours in length.
■
Recording will stop automatically if a copy
protected image is selected.
■
DVD-RAM/-RW discs must be formatted
before starting to record. Most new discs
are sold unformatted.
■
Do not use DVD-R authoring discs with
this unit.
NOTE
Record Mode SP 031:39
4
Press the REC button.
Information concerning the channel is displayed
on the screen, then recording begins.
Icon( ) is displayed on the front panel.
Recording
Recording : PR 1 [SP]
- To pause recording • Press the REC PAUSE button to pause a recording
in progress.
• Press the REC PAUSE button again during pause to
resume recording.
• You can switch channels by pressing the
PROG (
) buttons while recording pauses.
- To stop recording Press the STOP ( ) button to stop or finish a
recording in progress.
• When using DVD-RAM/-RW/-R discs, the message
“Updating the information of disc. Please wait for a
moment” is displayed.
78 - English
6-00819S-XSA_75-92_REC
6/9/05
2:52 PM
Page 79
Recording from external
equipment you are watching
4
Press the REC button.
Information concerning the external input mode is
displayed on the screen, then recording begins.
Icon(
) is displayed on the front panel.
- To pause recording Before you start
Check that the disc has enough available space for the
recording. Adjust the recording mode.
• Press the REC PAUSE button to pause a recording
in progress.
• Press the REC PAUSE button again during pause to
resume recording.
• You can switch channels by pressing the
PROG (
) buttons while recording pauses.
1
2
Press the HDD or DVD button.
If you select DVD, Press the OPEN/CLOSE button and
place a recordable disc on the disc tray. Press the
OPEN/CLOSE button to close the disc tray.
Wait until LOAD disappears from the front panel display.
If an unused DVD-RAM disc is used, whether to format
or not will be asked first. (See page 76)
If an unused DVD-RW disc is used, whether to initialize
or not will be asked first. (See page 76)
- To stop recording Press the STOP ( ) button to stop or finish a
recording in progress.
• When using DVD-RAM/-RW/-R discs, the
message “Updating the information of disc. Please
wait for a moment” is displayed.
Press the INPUT button to select the input source
according to the connection you made.
The front panel display changes in the following
sequence:
➞ PR Number ➞ AV1 ➞ AV2 ➞ DV
If you connect a digital camcorder, press the INPUT
button to select DV. (See page 80)
Recording
3
Press the REC MODE button repeatedly, (or press
the REC MODE button, then press the …† buttons)
to select the recording speed (quality).
➞ SP ➞ LP ➞ EP ➞ XP
Record Mode SP 031:39
English - 79
6-00819S-XSA_75-92_REC
6/9/05
2:52 PM
Page 80
Copying from a Camcorder
4
Press the INPUT button to select DV.
If the input is set to DV, a playback/record menu that
enables camcorder control appears on the top of the
screen.
DV
The DV device is connected.
You may control the Camcorder using the IEEE1394 (DV)
interface.
MOVE
RETURN
1
Connect the DV output jack of your camcorder to the
DV input jack on the front of your HDD & DVD
RECORDER using a DV cable.
5
Select the Play (√) icon on the upper part of the
screen to playback the camcorder and find the
starting position to copy.
You can press the PLAY ( ) button of the remote
control to play the camcorder.
2
Press the HDD or DVD button.
If you select DVD, Press the OPEN/CLOSE button and
place a recordable disc on the disc tray. Press the
OPEN/CLOSE button to close the disc tray. Wait until
LOAD disappears from the front panel display.
6
3
Press the REC MODE button repeatedly to select
the recording speed(quality).
To start recording, use the œ √ buttons to select
Record ( ● ) icon in the top side of the screen, then
press the OK button.
You can press the REC button of the remote control
to start recording. To display playback related icons
on the screen, press any direction button on the
remote control.
➞ SP ➞ LP ➞ EP ➞ XP
Recording
SELECT
- To stop recording Press the STOP ( ) button to stop or finish a
recording in progress.
Record Mode SP 031:39
• When using DVD-RAM/-RW/-R discs, the
message “Updating the information of disc.
Please wait for a moment” is displayed
80 - English
6-00819S-XSA_75-92_REC
6/9/05
2:52 PM
Page 81
Making an One Touch
Recording (OTR)
■
NOTE
The timer counter decreases by the
minute from 8:00 to 0:00, then the HDD &
DVD RECORDER stops recording.
- To stop recording You can set the HDD & DVD RECORDER to record in 30minute increments up to 8 hours by pressing the REC
button.
Press the STOP ( ) button. The message “Do you
want to stop recording?” is displayed.
• Press the œ √ buttons to select Yes, then press the
OK button.
• Or press the STOP (
1
Press the HDD or DVD button.
If you select DVD, Press the OPEN/CLOSE button and
place a recordable disc on the disc tray. Press the
OPEN/CLOSE button to close the disc tray. Wait until
LOAD disappears from the front panel display.
2
Press the PROG (
) or number buttons to select
the programme to record. If you want to record
through a connected external component, press the
INPUT button to select an appropriate external
input(AV1, AV2, DV or PR01).
3
Press the REC button to start recording.
OTR Mode
0:30
) button again.
About INFO button
During recording, press the INFO button once, the system
information screen appears.: Displays Active Status,
Background Status, and Main Screen information.
HDD
Active status
Background Status
Screen
01/JAN/2005 (SAT)
System Info
Record XP
––
Recording:PR3 [SP]
12:00
Pressing the INFO button twice, Disc information screen
appears.: Displays Total numbers of Titles and Playlists,
Recordable Time(Title), Available Space(Music/Photo).
4
Press the REC button repeatedly to adjust the
desired recording time.
➞ 0:30 ➞ 1:00 ➞ ... 8:00 ➞ Off
Disc Info
15
2
17:12 XP
10033 MB
12:00
Pressing the INFO button three times: Current recording
information screen appears.: Displays information of recording
Name, Title, Created Time and Recording Time.
HDD
Name
Recording Info
01/JAN/2005 12:00 PR
3
Recording Title
4
Created Time
01/JAN/2005 12:00
Recording Time
00:13:27
01/JAN/2005 (SAT)
12:00
English - 81
Recording
HDD
Total Title
Total Playlist
Recordable Time : Title
Available Space:Music/Photo
01/JAN/2005 (SAT)
6-00819S-XSA_75-92_REC
6/9/05
2:52 PM
Page 82
2
Chasing Play
Press the OK or PLAY ( ) button.
It plays back the title that you are currently
recording from the beginning.
√ Play
You can play back from the beginning of the programme
you are recording.
While Recording
1
Press the PLAY (
) button.
It plays back the title that you are currently
recording from the beginning.
Playback is not available for 10 seconds from the
start of recording.
You can use the SKIP (
) and other
playback-related buttons to view the previous
recorded list.
- Stopping Playback / Recording -
1
Press the STOP ( ) button. Playback screen
disappears and the recording in progress screen
appears.
2
Pressing the STOP (
stop the recording.
√ Play
■
NOTE
■
Recording
■
Using the TITLE LIST button
1
With the unit in recording mode, press the TITLE LIST
button.
The Title List screen is displayed.
Press the …†/SKIP (
) buttons to select the
recording title list.
Title List
HDD
No.
RECORDING...
008
009
010
011
012
Title
18/JAN/2005 02:15P
19/JAN/2005 14:15P
20/JAN/2005 16:05P
25/JAN/2005 17:00P
RECORDING...
Length
00:10:21
00:40:03
00:40:15
00:30:16
00:00:00
19/JAN/2005 12:15
SP
V-Mode Compatibility
MOVE
82 - English
2/2Page
SELECT
RETURN
EXIT
) button once more will
No sound is heard during search mode.
DVD disc playback is available during HDD
recording. However, JPEG, MP3, and DivX
files in the disc cannot be played back.
HDD playback is available during DVD
recording. However, JPEG and MP3 files in
the HDD cannot be played back.
6-00819S-XSA_75-92_REC
6/9/05
2:52 PM
Page 83
Simultaneous
Recording and Playback
1
Press the STOP ( ) button. Playback screen
disappears and the recording in progress screen
appears.
You can watching the previous title list while recording a
programme.
2
Pressing the STOP (
stop the recording.
- Stopping Playback / Recording -
■
) button once more will
No sound is heard during search mode.
NOTE
Using the TITLE LIST button
1
With the unit in recording mode, press the TITLE
LIST button.
The Title List screen is displayed.
Title List
HDD
No.
18/JAN/2005 12:15 PR 7
008
009
010
011
012
Title
Length
18/JAN/2005 02:15P
19/JAN/2005 14:15P
20/JAN/2005 16:05P
25/JAN/2005 17:00P
RECORDING...
00:10:21
00:40:03
00:40:15
00:30:16
00:00:00
18/JAN/2005 12:15
SP
V-Mode Compatibility
MOVE
Press the …†/ SKIP (
RETURN
EXIT
) buttons to select the
Recording
2
2/2Page
SELECT
title, then press the OK or PLAY ( ) button.
Selected title list will be played back.
√ Play
English - 83
6-00819S-XSA_75-92_REC
6/9/05
2:52 PM
Page 84
Making a Timer
Recording
3
Press the OK button to select Add a list.
The Timer Record List screen is displayed.
Timer Record List
HDD
No.
To
Current Time 12:00
Source
Date
Title No. 01
Start
End
To
Source
Date
Start
End
HDD
PR 02
01 JAN
12 : 00
14 : 00
Title
Available Time
1. Check the antenna cable is connected.
2. Check the remaining time of the disc.
3. Check the date and time are correct.
Make sure the Clock (Setup-Clock Set) must be set
before you proceed with a timer recording. (See page
26)
Available Time
Mode
Add a list
HDD
HDD
MOVE
Mode
SP
Save
29:10 SP
29:10 SP
SELECT
RETURN
EXIT
Using the ANYKEY button.
• Press the ANYKEY button.
• Press the …† buttons to select Add, then press
the OK or √ button.
Using the TIMER button
1
With the unit in Stop mode/Playback mode,
press the TIMER button.
The Programme screen is displayed.
4
Set timer recording option.
• Fill the input items using the …†œ √ buttons and
number buttons.
œ √ : Moves to the previous/next item.
…† 0~9 : Sets a value.
Programme
HDD
√
G-Code
Title
√
Timer Record
Music
G-Code Extended
√
: Off
Photo
Programme
Setup
Recording
MOVE
SELECT
RETURN
EXIT
• To : Select the media to record HDD or DVD.
• Source : The video input source (AV1, AV2), or the
broadcasting channel you want to make a timer
recording from.
• Date : Timer Recording allows setting the
recording time within one month period. Set the
recording day. (day/month)
Using the MENU button.
• With the unit in Stop mode/Playback mode, press
the MENU button.
• Press the …† buttons to select Programme,
then press the OK or √ button.
01 JAN
02 JAN
03 JAN
30 JAN
31 JAN
2
Press the …† buttons to select Timer Record,
then press the OK or √ button.
Timer Record List
HDD
No.
To
Current Time 12:00
Source
Date
Start
End
Mode
Add a list
Available Time
HDD
MOVE
84 - English
29:10 SP
SELECT
RETURN
EXIT
Every Day
MON-SAT
MON-FRI
Every SAT
Every SUN
6-00819S-XSA_75-92_REC
6/9/05
2:52 PM
Page 85
• Start/End Time : Start and end time of the timer
recording.
• Mode (Recording Mode) :
- FR (Flexible Recording) : Select when you want to
set video quality automatically. In FR mode, the
most suitable record mode is adjusted automatically,
according to remaining time on the disc and length
of the timer recording. This function is selected only
one mode in XP, SP, LP and EP modes.
5
After selecting the set up value for each mode, press the
OK button to select Save, and press the OK button
again.
•
will appear on the front panel. It means that a
timer recording is registered.
If the timer settings overlap;
The programmes are recorded in order of priority.
If timer recording is set for the first programme and
then again for the second programme and both
programmes overlap, the following message will
appear on the screen: “This setting is identical with
1.” The message shows that the first programme
has priority. After recording of the first programme is
complete, the second programme starts being
recorded.
- XP (high quality) : Select when video quality is
important.
- SP (standard quality) : Select to record in standard
quality.
- LP (low quality) : Select when a long recording time
is required.
- EP (extended) : Select when a longer recording time
is required.
To exit without saving the current setting
Press the MENU button.
■
NOTE
When you are recording at EP mode on a
DVD-RW(V mode)/-R disc, it may not
record the full 6 or 8 hours because the
unit uses the VBR(Variable Bit Rate)
ENCODING system. For example, if you
record a programme with a lot of action, it
uses a higher bit rate which in turn
consumes more disc memory.
• TITLE : To label the title name, select the title and then press
the OK button.Title renaming screen appears.
See page 94 for the registration.
To return to the previous menu
Press the RETURN button if you don’t want to set a
timer recording.
6
When you want to recording on DVD-RAM/-RW/-R,
you must insert the disc.
7
Turn the power off to finish the Timer Recording
setting.
Timer Recording will not work when the power is on.
The timer recording time may differ from the
set time depending on disc status and
overall timer recording status (for example,
recording times overlapping, or when the
previous recording ends within 2 minutes
before the start time of the next recording.)
■
You can make the Timer Recording up to 12
programmes.
■
If HDD disk has no available recording
space, blinks. It means that HDD disk has
no space to record.
NOTE
English - 85
Recording
■
6-00819S-XSA_75-92_REC
6/9/05
2:52 PM
Page 86
Flexible Recording
(for Timer recording only)
Editing the Timer
Record List
Follow these directions to edit the timer record list.
In FR mode, the most suitable record mode is adjusted
automatically, according to remaining time on the disc
and length of the timer recording. This function is
selected only one mode in XP, SP, LP and EP modes
and you can use this mode for timer recording.
The FR mode recording setup is the same as Timer
Recording. When setting the mode in step 4, set the FR
mode.
Using the TIMER button
1
With the unit in Stop mode/Playback mode, press
the TIMER button. The Programme screen is
displayed.
Programme
HDD
√
G-Code
Title
√
Timer Record
Music
G-Code Extended
√
: Off
Photo
Programme
Setup
MOVE
SELECT
RETURN
EXIT
Using the MENU button.
• With the unit in Stop mode/Playback mode, press
the MENU button.
Recording
• Press the …† buttons to select Programme,
then press the OK or √ button.
2
Press the …† buttons to select Timer Record, then
press the OK or √ button.
Timer Record List
HDD
Current Time 12:00
No.
To
Source
01
02
03
HDD
HDD
HDD
PR 02
PR 07
AV2
Available Time
Date
HDD
MOVE
86 - English
Start
01 JAN
12 : 00
15 JAN
14 : 10
01 JAN
15 : 10
Add a list
End
Mode
14 : 00
14 : 30
15 : 30
SP
SP
SP
29:10 SP
SELECT
RETURN
EXIT
6-00819S-XSA_75-92_REC
6/9/05
2:52 PM
Page 87
=
3
Press the …† buttons to select the number of the
Timer Record List you want to edit, then press the
ANYKEY button.
• The Add, Edit, Delete and Go To History List items
are displayed.
Timer Record List
HDD
No.
01
02
03
To
Current Time 12:00
Source
HDD
HDD
HDD
Add
Date
PR 02
PR 07
AV2
Start
01 JAN
12 : 00
15 JAN
14 : 10
01 JAN
15 : 10
Add a list
Edit
End
Mode
14 : 00
14 : 30
15 : 30
SP
SP
SP
Deleting a Timer
Record List
Follow these directions to delete an entry from the timer
record list.
Delete
Go ToTime
History List
Available
HDD
29:10 SP
MOVE
SELECT
RETURN
EXIT
Using the TIMER button
4
Press the …† buttons to select Edit, then press the
OK or √ button.
• The Timer Record Input item is displayed.
Edit the items you want to modify. See the “Making a
Timer Recording” section for more information on
Timer Recording Input items.(See page 84)
1
With the unit in Stop mode/Playback mode, press
the TIMER button. The Programme screen is
displayed.
Programme
HDD
√
G-Code
Title
√
Timer Record
Music
Timer Record List
HDD
No.
To
Current Time 12:00
Source
Date
Title No. 01
Start
End
Mode
Programme
To
Source
Date
Start
End
Mode
HDD
PR 02
01 JAN
12 : 00
14 : 00
SP
Title
Available Time
HDD
HDD
MOVE
√
: Off
Photo
Add a list
Available Time
G-Code Extended
Setup
MOVE
Save
SELECT
RETURN
EXIT
29:10 SP
29:10 SP
SELECT
RETURN
EXIT
Using the MENU button.
5
Press the OK button to select Save, then press the
OK button to confirm the edited setting.
6
Press the MENU button after finishing the operation.
The Timer Record List screen will disappear.
• Press the …† buttons to select Programme,
then press the OK or √ button.
2
Press the …† buttons to select Timer Record, then
press the OK or √ button.
Timer Record List
HDD
Current Time 12:00
No.
To
Source
01
02
03
HDD
HDD
HDD
PR 02
PR 07
AV2
Available Time
Date
Start
01 JAN
12 : 00
15 JAN
14 : 10
01 JAN
15 : 10
Add a list
HDD
MOVE
End
Mode
14 : 00
14 : 30
15 : 30
SP
SP
SP
29:10 SP
SELECT
RETURN
EXIT
English - 87
Recording
• With the unit in Stop mode/Playback mode, press
the MENU button.
6-00819S-XSA_75-92_REC
3
6/9/05
2:52 PM
Page 88
Press the …† buttons to select the number of the
Timer Record List you want to delete, and then
press the ANYKEY button.
• The Add, Edit, Delete and Go To History List
items are displayed.
Timer Record List
HDD
No.
01
02
03
To
Go To History List
You can confirm the performance results of title lists that have
passed the reserved recording time.
Current Time 12:00
Source
HDD
HDD
HDD
Add
Date
PR 02
PR 07
AV2
Start
01 JAN
12 : 00
15 JAN
14 : 10
01 JAN
15 : 10
Add a list
Edit
End
Mode
14 : 00
14 : 30
15 : 30
SP
SP
SP
Delete
Go ToTime
History List
Available
HDD
MOVE
29:10 SP
SELECT
RETURN
EXIT
Using the TIMER button
4
Press the …† buttons to select Delete, then press
the OK or √ button.
• You will be prompted with the delete confirm
message such as “Do you want to delete No.01?”.
1
With the unit in Stop mode/Playback mode, press
the TIMER button. The Programme screen is
displayed.
Programme
Timer Record List
HDD
No.
To
01
02
03
HDD
HDD
HDD
HDD
Current Time 12:00
Source
Date
Start
End
√
G-Code
Title
Mode
√
Timer Record
PR 02
01 JAN
12 : 00
14 : 00
PR 07
15 JANto delete
14 : 10
14 : 30
Do
you want
No.01?
AV2
01 JAN
15 : 10
15 : 30
Yes Add a list No
Available Time
HDD
MOVE
SP
SP
SP
Music
G-Code Extended
√
: Off
Photo
Programme
Setup
29:10 SP
SELECT
RETURN
MOVE
EXIT
SELECT
RETURN
EXIT
Recording
Using the MENU button.
5
Press the œ √ buttons to select Yes, then press the
OK button.
• The selected entry will be deleted from the list.
• With the unit in Stop mode/Playback mode, press
the MENU button.
• Press the …† buttons to select Programme,
then press the OK or √ button.
Timer Record List
HDD
Current Time 12:00
No.
To
Source
01
02
HDD
HDD
PR 07
AV2
Date
Start
15 JAN
14 : 10
01 JAN
15 : 10
Add a list
End
Mode
14 : 30
15 : 30
SP
SP
2
Press the …† buttons to select Timer Record, then
press the OK or √ button.
Timer Record List
Available Time
HDD
HDD
29:10 SP
No.
MOVE
6
SELECT
RETURN
Source
EXIT
Press the MENU button after finishing the operation.
The Timer Record List screen will disappear.
88 - English
To
Current Time 12:00
Date
Start
End
Mode
Add a list
Available Time
HDD
MOVE
29:10 SP
SELECT
RETURN
EXIT
6-00819S-XSA_75-92_REC
3
6/9/05
2:52 PM
Page 89
Information about History List
Press the ANYKEY button.
• The Add and Go To History List items are
displayed.
Informs whether the selected History List performed a
Timer Recording successfully.
Timer Record List
HDD
Current Time 12:00
No.
To
Source
Date
Start
End
Mode
01
--
---
-- / --
--:--
--:--
--
-1 Press the …† buttons to select the number of the
History List, then press the ANYKEY button.
5
--
History List
HDD
Add
Available
HDD
Go ToTime
History List
MOVE
29:10 SP
SELECT
RETURN
EXIT
No. Source
Date
Start
End
Mode
To
Status
01 PR 02
02 PR 07
03 AV2
Info
01 JAN
15 JAN
01 JAN
12 : 00
14 : 10
15 : 10
14 : 00
14 : 30
15 : 30
SP
SP
SP
HDD
HDD
HDD
OK
OK
OK
Delete
4
List Clear
Press the …† buttons to select Go To History List,
then press the OK or √ button.
The History List screen is displayed.
History List
HDD
No. Source
01
02
03
PR 02
PR 07
AV2
Date
Start
End
Mode
To
Status
01 JAN
15 JAN
01 JAN
12 : 00
14 : 10
15 : 10
14 : 00
14 : 30
15 : 30
SP
SP
SP
HDD
HDD
HDD
OK
OK
OK
Go To Timer Rec List
MOVE
SELECT
RETURN
EXIT
Press the …† buttons to select Info, then press the
OK or √ button.
6
History List
HDD
No. Source
MOVE
SELECT
RETURN
01
02
03
EXIT
Date
Start
End
Mode
To
PR 02 01 JAN 12 : 00 14 : 00
SP
HDD
PR 07 15 JAN 14 : 10 14 : 30
SP
HDD
Timer rec was finished successfully
AV2
01 JAN 15 : 10 15 : 30
SP
HDD
Status
OK
OK
OK
OK
5
MOVE
SELECT
RETURN
EXIT
Press the MENU button after finishing the operation.
The History List screen will disappear.
Recording
Delete History List
Deletes a History List individually.
-1 Press the …† buttons to select the number of
the history list you want to delete, and then press
the ANYKEY button.
5
History List
HDD
No. Source
Date
Start
End
Mode
To
Status
01 PR 02
02 PR 07
03 AV2
Info
01 JAN
15 JAN
01 JAN
12 : 00
14 : 10
15 : 10
14 : 00
14 : 30
15 : 30
SP
SP
SP
HDD
HDD
HDD
OK
OK
OK
Delete
List Clear
Go To Timer Rec List
MOVE
SELECT
RETURN
EXIT
English - 89
6-00819S-XSA_75-92_REC
6/9/05
2:52 PM
Page 90
Go To Timer Rec List
Press the …† buttons to select Delete, then press
the OK or √ button.
6
History List
HDD
No. Source
01
02
03
PR 02
PR 07
AV2
Date
Start
End
Mode
To
01 JAN 12 : 00 14 : 00
SP
HDD
15Do
JANyou14want
: 10 to14delete
: 30 No.01?
SP
HDD
01 JAN 15 : 10 15 : 30
SP
HDD
Yes
No
MOVE
SELECT
Switches directly from the History List to the Timer Rec List.
-1 Press the ANYKEY button.
5
Status
OK
OK
OK
RETURN
History List
HDD
EXIT
No. Source
Date
Start
End
Mode
To
Status
01 PR 02
02 PR 07
03 AV2
Info
01 JAN
15 JAN
01 JAN
12 : 00
14 : 10
15 : 10
14 : 00
14 : 30
15 : 30
SP
SP
SP
HDD
HDD
HDD
OK
OK
OK
Delete
List Clear
Go To Timer Rec List
MOVE
6
Clear History List
SELECT
RETURN
EXIT
Press the …† buttons to select Go To Timer Rec
List, then press the OK or √ button.
Clears all History Lists at once.
Timer Record List
HDD
No.
-1 Press the ANYKEY button.
5
To
Current Time 12:00
Source
Date
Start
End
Mode
Add a list
History List
Available Time
HDD
29:10 SP
HDD
MOVE
No. Source
Date
Start
End
Mode
To
Status
01 PR 02
02 PR 07
03 AV2
Info
01 JAN
15 JAN
01 JAN
12 : 00
14 : 10
15 : 10
14 : 00
14 : 30
15 : 30
SP
SP
SP
HDD
HDD
HDD
OK
OK
OK
Delete
Recording
List Clear
Go To Timer Rec List
MOVE
6
SELECT
RETURN
EXIT
Press the …† buttons to select List Clear, then
press the OK or √ button.
History List
HDD
No. Source
01
02
03
Date
Start
End
Mode
To
PR 02 01 JAN 12 : 00 14 : 00
SP
HDD
PR 07 Do15you
JANwant
14 : to
10 delete
14 : 30a history
SP list?
HDD
AV2
01 JAN 15 : 10 15 : 30
SP
HDD
Yes
No
MOVE
90 - English
SELECT
RETURN
Status
OK
OK
OK
EXIT
SELECT
RETURN
EXIT
6-00819S-XSA_75-92_REC
6/9/05
2:52 PM
Page 91
Using the G-Code
Feature
3
Press the number buttons to enter the code of the
programme that you want to record in your
television magazine.
• If you want to correct the G-Code code that
you are entering:
• Press the œ button until the digit to be corrected
is cleared.
• Enter the correct digit.
4
Press the OK button.
• The information concerning the programme is
displayed.
• When using the G-Code function for the
first time with stored stations, you must enter the
PR number manually by pressing the …†
buttons or number buttons.
Before presetting your HDD & DVD RECORDER:
• Switch on both the television and your HDD & DVD
RECORDER.
• Check that the date and time are correct.
Up to twelve programmes can be preset.
Using the TIMER button
1
With the unit in Stop mode/Playback mode, press
the TIMER button. The Programme screen is
displayed.
Timer Record List
HDD
Programme
No.
To
Current Time 12:00
Source
Date
Start
End
Mode
HDD
√
G-Code
Title
√
Timer Record
Music
Add a list
G-Code Extended
√
: Off
Photo
Available Time
Programme
HDD
29:10 SP
MOVE
Setup
MOVE
SELECT
RETURN
SELECT
RETURN
EXIT
EXIT
Timer Record List
Using the MENU button.
HDD
No.
To
Source
• Press the …† buttons to select Programme,
then press the OK or √ button.
2
Start
End
To
Source
Date
Start
End
HDD
PR 02
01 JAN
12 : 00
14 : 00
Title
Available Time
Available Time
Mode
Add a list
HDD
HDD
MOVE
Press the …† buttons to select G-Code, then press the
OK or √ button.
• A message is displayed to allow you to enter the
G-Code.
Date
Title No. 01
Mode
SP
Save
29:10 SP
29:10 SP
SELECT
RETURN
EXIT
5
If the programme and times are correct, press the
OK button.
Press the OK button to confirm the setting.
6
Turn the power off by pressing the DVD STANDBY/ON
button to activate the timer recording setting.
7
Refer to pages 86~88 if you wish to:
• Check whether the timer Recording has set
correctly or not.
• Cancel a preset recording
G-Code
HDD
Enter G-Code number. [0~9]
0~9 NUMBER
SELECT
RETURN
EXIT
English - 91
Recording
• With the unit in Stop mode/Playback mode, press
the MENU button.
Current Time 12:00
6-00819S-XSA_75-92_REC
■
NOTE
■
6/9/05
2:52 PM
Page 92
The numbers next to each TV programme
listing in the magazines or newspapers
are G-Code numbers, which allow you to
programme your HDD & DVD
RECORDER instantly with the remote
control. Enter the G-Code for the
programme you wish to record.
2
Press the …† buttons to select G-Code Extended,
then press the OK or √ button.
Programme
HDD
Timer Record
Music
G-Code Extended
Photo
Programme
Setup
MOVE
G-Code Extended
To prevent delays or overruns, HDD & DVD RECORDER has
a function called G-Code Extened allowing you to extend the
recording time by up to 60 minutes.
Recording
Using the TIMER button
1
With the unit in Stop mode/Playback mode, press
the TIMER button. The Programme screen is
displayed.
Programme
HDD
√
G-Code
Title
√
Timer Record
Music
G-Code Extended
: Off
√
Photo
Programme
Setup
MOVE
SELECT
RETURN
EXIT
Using the MENU button.
• With the unit in Stop mode/Playback mode, press
the MENU button.
• Press the …† buttons to select Programme,
then press the OK or √ button.
92 - English
√
G-Code
Title
G-Code is a trademark of Gemstar
Development Corporation. The G-Code
system is manufactured under licence
from Gemstar Development Corporation.
SELECT
Off
: Off
10
20
30
40
50
60
√
RETURN
EXIT
√
3
Press the …† buttons to select the G-Code
Extended time, then the press OK or √ button.
4
Press the MENU button to exit the menu.
7-00819S-XSA_93-100_EDIT
6/9/05
2:54 PM
Page 93
Editing
This section introduces basic functions of
editing and explains both edit functions for the
recording on a disc and edit functions for the
entire disc.
Basic Editing (Title List) . . . . . . . . . . . . . . . . . . . . .94
Advanced Editing (Playlist) . . . . . . . . . . . . . . . . . .101
Copying from HDD to DVD . . . . . . . . . . . . . . . . . .109
Copying Multiple Titles at One Time . . . . . . . . . . .112
• Play List
This refers to a unit of playback, which is made by
selecting a desired scene in the entire Title List.
When one playlist is played, only the scene selected by
the user will play and then stop. Since only the
information necessary for playing a desired scene is
included in a playlist, even if that playlist is deleted, the
original stream will not be deleted.
Copying from DVD to HDD . . . . . . . . . . . . . . . . . .116
Copying MP3 or JPEG Files
from a Disc to HDD . . . . . . . . . . . . . . . . . . . . . . .117
Disc Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . .119
Recording or editing might not be completed if an
error, such as a sudden power failure occurs.
Please be aware that a material that has been
damaged is unable to be retrieved to its
original content.
English - 93
Editing
• Title List
A title is a section of recorded video and audio.
Title List shows a list to help you select a title.
Since the title consists of the information on stream that
is actually recorded, if one title is deleted, that title
cannot be played again.
7-00819S-XSA_93-100_EDIT
6/9/05
2:54 PM
Page 94
Basic Editing (Title List)
3
Press the …† buttons to select Rename, then press
the OK or √ button.
The Rename screen is displayed.
Rename
HDD
Renaming(Labeling) a Title
1 8 / JAN / 2005 12:15 PR 7
Follow these instructions to rename a title list entry,
i.e., to edit the title of a recorded programme.
Back Space
MOVE
Using the TITLE LIST button
1
4
With the unit in Stop mode/Playback mode, press the
TITLE LIST button.
The Title List screen is displayed.
Space Delete
SELECT
Clear
RETURN
Save
EXIT
Select the desired characters using the …† œ √
buttons, press the OK button.
Rename
HDD
Sports(A1)
Title List
HDD
No.
001
002
003
004
Title
Length
18/JAN/2005 12:15P
19/JAN/2005 12:15P
20/JAN/2005 12:15P
25/JAN/2005 12:15P
00:10:21
00:40:03
00:20:15
00:50:16
Back Space
MOVE
Space Delete
SELECT
Clear
RETURN
Save
EXIT
18/JAN/2005 12:15 PR 7
18/JAN/2005 12:15
SP
V-Mode Compatibility
MOVE
• Back Space: Deletes and moves the cursor
backwards by one position. (Equivalent to the
CANCEL button)
• Space: Enters a blank and moves the cursor one
forward (to the right).
• Delete: Deletes the character at the cursor position.
• Clear: Deletes all the character inputs.
• Save: Registers the character inputs.
1/1 Page
SELECT
RETURN
EXIT
Using the MENU button.
• With the unit in Stop mode/Playback mode, press
the MENU button.
• Press the …† buttons to select Title,
Editing
then press the OK or √ button twice.
2
Press the …† buttons to select an entry you want to
rename from the Title List, then press the ANYKEY
button.
5
Press the …† œ √ buttons to select Save, and then
press the OK button.
The changed title name is displayed on the title item
of the selected entry.
Title List
HDD
Rename
No.
Protection
001
002
003
004
Copy
Delete
Edit
√
Playlist
√
19/JAN/2005 12:15PR 7
Title
18/JAN/2005 12:15P
19/JAN/2005 12:15P
20/JAN/2005 12:15P
25/JAN/2005 12:15P
94 - English
HDD
No.
00:10:21
00:40:03
00:20:15
00:50:16
001
002
003
004
Title
Sports(A1)
19/JAN/2005 12:15P
20/JAN/2005 12:15P
25/JAN/2005 12:15P
Length
00:10:21
00:40:03
00:20:15
00:50:16
Sports(A1)
√
Navigation
19/JAN/2005 12:15
√
Select Media
SP V-Mode Compatibility
Disc Manager
MOVE
Title List
Length
18/JAN/2005 12:15
1/1 Page
SELECT
RETURN
SP
EXIT
V-Mode Compatibility
MOVE
1/1 Page
SELECT
RETURN
EXIT
7-00819S-XSA_93-100_EDIT
6/9/05
2:54 PM
Page 95
Locking (Protecting) a Title
Follow these instructions to lock an entry to protect it
from accidental deletion.
3
Press the …† buttons to select Protection, then press
the OK or √ button.
Title List
HDD
Title Protection:
18/JAN/2005 12:15 PR 7
Using the TITLE LIST button
V-Mode Compatibility
MOVE
With the unit in Stop mode/Playback mode, press the
TITLE LIST button .
The Title List screen is displayed.
Title List
HDD
No.
001
002
003
004
Title
Length
18/JAN/2005 12:15P
19/JAN/2005 12:15P
20/JAN/2005 12:15P
25/JAN/2005 12:15P
00:10:21
00:40:03
00:20:15
00:50:16
Off
18/JAN/2005 12:15
SP
1
On
4
SELECT
RETURN
Press the œ √ buttons to select On, then press the
OK button. The key icon on the information window
for the selected entry changes to the locked status.
( ➝ )
Title List
18/JAN/2005 12:15 PR 7
HDD
18/JAN/2005 12:15
SP
V-Mode Compatibility
MOVE
EXIT
No.
001
002
003
004
1/1 Page
SELECT
RETURN
EXIT
Title
18/JAN/2005 12:15P
19/JAN/2005 12:15P
20/JAN/2005 12:15P
25/JAN/2005 12:15P
Length
00:10:21
00:40:03
00:20:15
00:50:16
18/JAN/2005 12:15 PR 7
18/JAN/2005 12:15
SP
Using the MENU button.
V-Mode Compatibility
MOVE
1/1 Page
SELECT
RETURN
EXIT
• With the unit in Stop mode/Playback mode,
press the MENU button.
• Press the …† buttons to select Title,
then press the OK or √ button twice.
2
Press the …† buttons to select an entry you want to
protect from the Title List, then press the ANYKEY
button.
Title List
No.
Protection
001
002
003
004
Copy
Delete
Edit
√
Playlist
√
19/JAN/2005 12:15PR 7
Title
18/JAN/2005 12:15P
19/JAN/2005 12:15P
20/JAN/2005 12:15P
25/JAN/2005 12:15P
√
Navigation
19/JAN/2005 12:15
√
Select Media
SP V-Mode Compatibility
Disc Manager
MOVE
Length
Editing
HDD
Rename
00:10:21
00:40:03
00:20:15
00:50:16
1/1 Page
SELECT
RETURN
EXIT
English - 95
7-00819S-XSA_93-100_EDIT
6/9/05
2:54 PM
Page 96
3
Deleting a Title
Press the …† buttons to select Delete, then press the
OK or √ button.
Follow these instructions to delete an entry from the
Title List.
Title List
HDD
Do you want to delete?
(Related playlists
may be deleted.)
18/JAN/2005 12:15 PR 7
Using the TITLE LIST button
With the unit in Stop mode/Playback mode, press the
TITLE LIST button.
The Title List screen is displayed.
No.
001
002
003
004
Title
Length
18/JAN/2005 12:15P
19/JAN/2005 12:15P
20/JAN/2005 12:15P
25/JAN/2005 12:15P
00:10:21
00:40:03
00:20:15
00:50:16
18/JAN/2005 12:15 PR 7
18/JAN/2005 12:15
SP
V-Mode Compatibility
MOVE
1/1 Page
SELECT
RETURN
SELECT
RETURN
EXIT
• The message may be different depend on the type of
disc. You will be prompted with the confirmation
message. HDD, DVD-RAM(VR mode), DVDRW(VR mode): Since Playlist is present, the
message “Do you want to delete? (Related
playlists may be deleted.)” is displayed.
DVD-RW(Video mode)/-R: Since Playlist is not
present, the message “Do you want to delete?” is
displayed.
Title List
HDD
No
V-Mode Compatibility
MOVE
1
Yes
18/JAN/2005 12:15
SP
EXIT
Using the MENU button.
• With the unit in Stop mode/Playback mode, press
the MENU button.
• Press the …† buttons to select Title,
4
Press the œ √ buttons to select Yes, then press the OK
button.
Title List
HDD
then press the OK or √ button twice.
Deleting...
(Please wait.)
2
Press the …† buttons to select an entry you want to
delete in the Title List, then press the ANYKEY button.
18/JAN/2005 12:15 PR 7
18/JAN/2005 12:15
SP
V-Mode Compatibility
EXIT
Title List
HDD
Rename
No.
Protection
001
002
003
004
Copy
Editing
Delete
Edit
√
Playlist
√
19/JAN/2005 12:15PR 7
Title
18/JAN/2005 12:15P
19/JAN/2005 12:15P
20/JAN/2005 12:15P
25/JAN/2005 12:15P
00:10:21
00:40:03
00:20:15
00:50:16
Title List
HDD
No.
Title
Length
001 19/JAN/2005 12:15P 00:40:03
003 20/JAN/2005 12:15P 00:20:15
004 25/JAN/2005 12:15P 00:50:16
√
Navigation
19/JAN/2005 12:15
√
Select Media
SP V-Mode Compatibility
Disc Manager
MOVE
Length
1/1 Page
SELECT
RETURN
19/JAN/2005 12:15 PR 7
EXIT
19/JAN/2005 12:15
SP
V-Mode Compatibility
MOVE
96 - English
1/1 Page
SELECT
RETURN
EXIT
7-00819S-XSA_93-100_EDIT
■
NOTE
6/9/05
2:54 PM
Page 97
You cannot delete a protected entry. If you
want to delete a protected entry, select
“Off” in the Title Protection menu. (See
page 95)
■
When the Disc Protection has been set to
Protected, you cannot delete titles. (See
page 120)
■
Once an entry is deleted from the Title List
it cannot be recovered.
■
Once DVD-RW/-R is finalised, it cannot be
deleted.
Splitting a Section of a Title (Split)
Follow these instructions to split a section of a Title
List entry.
Using the TITLE LIST button
1
With the unit in Stop mode/Playback mode, press the
TITLE LIST button.
The Title List screen is displayed.
Title List
HDD
No.
001
002
003
004
Title
Length
18/JAN/2005 12:15P
19/JAN/2005 12:15P
20/JAN/2005 12:15P
25/JAN/2005 12:15P
00:10:21
00:40:03
00:20:15
00:50:16
18/JAN/2005 12:15 PR 7
18/JAN/2005 12:15
SP
V-Mode Compatibility
MOVE
1/1 Page
SELECT
RETURN
EXIT
Using the MENU button.
• With the unit in Stop mode/Playback mode, press
the MENU button.
• Press the …† buttons to select Title,
then press the OK or √ button twice.
2
Press the …† buttons to select an entry you want to
Split from the Title List, then press the ANYKEY button.
Title List
No.
Protection
001
002
003
004
Copy
Delete
Edit
√
Playlist
√
19/JAN/2005 12:15PR 7
Title
18/JAN/2005 12:15P
19/JAN/2005 12:15P
20/JAN/2005 12:15P
25/JAN/2005 12:15P
√
Navigation
19/JAN/2005 12:15
√
Select Media
SP V-Mode Compatibility
Disc Manager
MOVE
Length
00:10:21
00:40:03
00:20:15
00:50:16
1/1 Page
SELECT
RETURN
EXIT
English - 97
Editing
HDD
Rename
7-00819S-XSA_93-100_EDIT
3
6/9/05
2:54 PM
Page 98
Press the …† buttons to select Edit, then press the
OK or √ button.
The Edit menu is display
Split
HDD
18/JAN/2005 12:15 PR 7
Title List No. 001
Title List
HDD
Rename
No.
Protection
001 18/JAN/2005 12:15P
002 19/JAN/2005 12:15P
003 20/JAN/2005 12:15P
004Split25/JAN/2005 12:15P
Copy
Delete
√
Edit
Playlist
√
Navigation
√
19/JAN/2005 12:15PR 7
19/JAN/2005 12:15
Title
4
Split 2
00:00:00
00:05:21
Length
00:05:21
00:10:21
00:40:03
00:20:15
00:50:16
Select
Split
Return
MOVE
SELECT
RETURN
EXIT
Partial Delete
√
Select Media
SP V-Mode Compatibility
Disc Manager
MOVE
Split 1
1/1 Page
SELECT
RETURN
6
EXIT
Press the OK button to select Split.
The message “This title cannot be recovered after
splitting. Do you want to split?” is displayed.
Press the …† buttons to select Split, then press the
OK or √ button.
Split
HDD
18/JAN/2005 12:15 PR 7
Split
HDD
Title List No. 05
18/JAN/2005 12:15 PR 7
Split 1
Split 2
This title cannot be recovered after spliting.
Title List No. 001
Do you want to split?
Split 1
Split 2
00:00:00
00:00:00
00:00:00
Yes
00:05:21
Select
Split
00:00:00
Select
Split
MOVE
5
MOVE
Return
SELECT
RETURN
7
No.
001
001
002
003
004
Editing
00:00:00
00:05:21
Split
MOVE
Return
SELECT
RETURN
➂
➁
EXIT
① First split interval
➁ Total recording time of title list
➂ Start time of the second split and its screen
98 - English
Title
18/JAN/2005 12:15P
18/JAN/2005 12:15P
19/JAN/2005 12:15P
20/JAN/2005 12:15P
25/JAN/2005 12:15P
Length
00:05:21
00:05:00
00:40:03
00:20:15
00:50:16
18/JAN/2005 12:15
Split 2
SP
Select
EXIT
18/JAN/2005 12:15 PR 7
Title List No. 001
①
RETURN
Title List
HDD
18/JAN/2005 12:15 PR 7
00:00:00
SELECT
Press the œ √ buttons to select Yes, then press the
OK button.
The split title is divided into two, and next titles will be
pushed back one by one.
Split
Split 1
Return
EXIT
Using the playback-related buttons (PLAY( ),
SEARCH (
)), move to a point for
splitting and press the OK button.
If it is not the point where you want to split, press the
RETURN button to cancel the selection. Using the
playback-related buttons, move to a point to split and
press the OK button.
HDD
00:05:21
No
V-Mode Compatibility
MOVE
1/1 Page
SELECT
RETURN
EXIT
7-00819S-XSA_93-100_EDIT
6/9/05
2:55 PM
Page 99
Deleting a Section of a Title (Partial
Delete)
3
Follow these instructions to delete a section of a
Title List entry.
Press the …† buttons to select Edit, then press the
OK or √ button.
The Edit Title List screen is display
Title List
HDD
Rename
No.
Protection
001 18/JAN/2005 12:15P
002 19/JAN/2005 12:15P
003 20/JAN/2005 12:15P
004Split25/JAN/2005 12:15P
Copy
(VR mode)
Delete
Edit
√
Playlist
√
19/JAN/2005 12:15PR 7
MOVE
With the unit in Stop mode/Playback mode, press the
TITLE LIST button.
The Title List screen is displayed.
4
Length
00:10:21
00:40:03
00:20:15
00:50:16
Partial Delete
√
Navigation
19/JAN/2005 12:15
√
Select Media
SP V-Mode Compatibility
Disc Manager
Using the TITLE LIST button
1
Title
1/1 Page
SELECT
RETURN
EXIT
Press the …† buttons to select Partial Delete, then
press the OK or √ button.
Partial Delete
HDD
18/JAN/2005 12:15 PR 7
Title List
HDD
No.
001
002
003
004
Title
Title List No. 001
Length
18/JAN/2005 12:15P
19/JAN/2005 12:15P
20/JAN/2005 12:15P
25/JAN/2005 12:15P
00:10:21
00:40:03
00:20:15
00:50:16
Start
End
00:00:00
00:00:00
00:01:00
18/JAN/2005 12:15 PR 7
Start
End
Delete
Return
18/JAN/2005 12:15
SP
MOVE
V-Mode Compatibility
MOVE
SELECT
SELECT
RETURN
EXIT
EXIT
5
Using the MENU button.
Press the OK button at the starting point.
The image and starting point time are displayed in the
section deletion starting point window.
• With the unit in Stop mode/Playback mode,
press the MENU button.
• Press the …† buttons to select Title,
Partial Delete
then press the OK or √ button twice.
2
RETURN
1/1 Page
HDD
18/JAN/2005 12:15 PR 7
Title List No. 001
Press the …† buttons to select an entry you want to
edit from the Title List, then press the ANYKEY button.
Start
End
00:01:00
00:00:00
00:01:00
Start
End
Delete
MOVE
Return
SELECT
RETURN
EXIT
Title List
No.
Protection
001
002
003
004
Copy
Delete
Edit
√
Playlist
√
Navigation
√
19/JAN/2005 12:15PR 7
19/JAN/2005 12:15
Title
18/JAN/2005 12:15P
19/JAN/2005 12:15P
20/JAN/2005 12:15P
25/JAN/2005 12:15P
√
Select Media
SP V-Mode Compatibility
Disc Manager
MOVE
Length
Editing
HDD
Rename
00:10:21
00:40:03
00:20:15
00:50:16
1/1 Page
SELECT
RETURN
EXIT
• When using DVD-RAM/-RW(VR) disc, you can
select Partial Delete directly by pressing the
ANYKEY button.
(Then go to step 5)
English - 99
7-00819S-XSA_93-100_EDIT
6/9/05
2:55 PM
Page 100
Edit Title List Screen Elements
7
Press the œ √ buttons to select Delete, then press
the OK button.
Partial Delete
HDD
18/JAN/2005 12:15 PR 7
Partial Delete
Title List No. 001
Start
HDD
End
18/JAN/2005 12:15 PR 7
Title List No. 001
00:01:00
①
00:00:00
00:06:35
Start
End
Delete
Return
➃
➁
Start
End
00:01:00
00:06:35
00:06:35
MOVE
SELECT
RETURN
EXIT
Start
End
MOVE
➂
① Playback bar
➁ Playtime
➂ Section deletion starting point window and time
➃ Section deletion end point window and time
• Select the start and end points of the section you
want to delete using the playback related buttons.
• Playback related buttons :
(PLAY( ), SEARCH (
))
6
Delete
Press the OK button at the end point.
The image and end point time are displayed in the
Section deletion ending point window.
Return
SELECT
RETURN
EXIT
Partial Delete
HDD
18/JAN/2005 12:15 PR 7
Title List No. 001
Start
End
Do you want to delete?
(Deleted part will not be restored.)
00:01:00
Yes
Start
End
Delete
MOVE
00:02:00
No
00:06:35
Return
SELECT
RETURN
EXIT
8
Press the œ √ buttons to select Yes, then press the
OK button. The selected section has been deleted.
9
Press the œ √ buttons to select Return, then press
the OK button to finish the operation.
Title List
HDD
18/JAN/2005 12:15 PR 7
Title List No. 001
Start
End
00:01:00
00:06:35
00:06:35
Start
End
Delete
MOVE
Return
SELECT
RETURN
EXIT
■
The length of the section to be deleted
must be at least 5 seconds long.
■
If the length of the section to be deleted is
less than 5 seconds, you will be prompted
with the message “The range is too
short.”.
■
If the end time precedes the starting time,
you will be prompted with the message
“End point cannot be marked earlier than
start point”.
■
The section cannot be deleted when it
includes a still picture.
■
Press the MENU button after the operation has
finished.
The Title List screen will disappear.
Editing
NOTE
100 - English
8-00819S-XSA_101-111_EDIT
6/9/05
2:58 PM
Page 101
3
Advanced Editing
(Playlist)
Press the …† buttons to select New Playlist,
then press the OK or √ button.
The Make Playlist screen is displayed.
Make Playlist
HDD
New Playlist
Scene No. 001
Creating a Playlist
Follow these instructions to create a new playlist entry
from a recorded title.
Title List 1/9
Start
End
00:00:00
00:00:00
00:00:10
Start
End
Make
MOVE
Return
SELECT
RETURN
EXIT
(VR mode)
Using the Title List button
1
4
Press the OK button at the start point.
With the unit in Stop mode/Playback mode, press the
Title List button.
The Title List screen is displayed.
Make Playlist
HDD
New Playlist
Scene No. 001
Title List 1/9
Start
End
00:00:10
00:00:00
Title List
HDD
No.
001
002
003
004
Title
00:00:10
Length
18/JAN/2005 12:15P
19/JAN/2005 12:15P
20/JAN/2005 12:15P
25/JAN/2005 12:15P
Start
End
00:10:21
00:40:03
00:20:15
00:50:16
Make
MOVE
Return
SELECT
RETURN
EXIT
18/JAN/2005 12:15 PR 7
• The image and time at the start point are displayed on
the Start window.
• The yellow-coloured selection bar moves to the End
item.
• Select the starting point of the section from which you
want to create a new scene using the playback
related buttons (PLAY( ), SEARCH (
)).
18/JAN/2005 12:15
SP
V-Mode Compatibility
MOVE
1/1 Page
SELECT
RETURN
EXIT
Using the MENU button.
• With the unit in Stop mode/Playback mode,
press the MENU button.
• Press the …† buttons to select Title,
then press the OK or √ button twice.
Press the OK button at the end point.
Make Playlist
Press the ANYKEY button.
Press the …† buttons to select Playlist, then
press the OK or √ button.
HDD
New Playlist
Scene No. 001
Title List 1/9
Start
End
00:00:10
00:10:10
00:10:10
Title List
HDD
Rename
No.
Protection
001
002
003
004
Copy
Delete
Title
18/JAN/2005 12:15P
19/JAN/2005 12:15P
20/JAN/2005 12:15P
25/JAN/2005 12:15P
Edit
√
Playlist
√
New Playlist
Navigation
√
Go To Playlist
19/JAN/2005 12:15PR 7
19/JAN/2005 12:15
√
Select Media
SP V-Mode Compatibility
Disc Manager
MOVE
Length
00:10:21
00:40:03
00:20:15
00:50:16
1/1 Page
SELECT
RETURN
EXIT
Editing
2
5
Start
End
MOVE
Make
Return
SELECT
RETURN
EXIT
• The image and end point time are displayed in the
End window.
• The yellow-coloured selection bar moves to the
Make item.
English - 101
8-00819S-XSA_101-111_EDIT
6/9/05
2:58 PM
Page 102
Playing Entries in the Playlist
6
Press the œ √ buttons to select Make,
then press the OK button.
• To make a scene for playlist.
A new Make scene screen is displayed.
Repeat steps 3~6 to make scene of playlist.
New scene will be added to the current playlist.
You can check and see all the scenes on Edit playlist
screen. (See page 104)
Follow these instructions to play the playlist entries.
(VR mode)
Using the PLAY LIST button
• To make a new playlist.
Repeat steps 1~6 if you want to make a new playlist.
7
Press the œ √ button to select Return,
then press the OK button for finishing the operation.
1
With the unit in Stop mode/Playback mode, press the
PLAY LIST button.
The Playlist screen is displayed.
Playlist
HDD
NOTE
■
You can create up to 99 playlist entries.
■
Depending on the kind of disc, the
displayed screen may have a slight
difference.
No.
001
002
003
004
Title
16/JAN/2005 12:15P
19/JAN/2005 12:15P
22/JAN/2005 12:15P
25/JAN/2005 12:15P
Length
00:10:21
00:40:03
00:20:15
00:50:16
16/JAN/2005 12:15 PR 7
16/JAN/2005 12:15
7 Scenes
1/1 Page
MOVE
SELECT
RETURN
EXIT
Using the MENU button.
• With the unit in Stop mode/Playback mode,
press the MENU button.
• Press the …† buttons to select Title,
then press the OK or √ button twice.
The Title List screen is displayed.
• Press the ANYKEY button.
• Press the …† buttons to select Playlist, then press
the OK or √ button.
Editing
• Press the …† buttons to select Go To Playlist,
then press the OK or √ button.
102 - English
2
Press the …† buttons to select the playlist you
want to play, then press the OK or PLAY ( )
button.
3
Press the STOP ( ) button to stop playing.
The screen returns to the Playlist screen.
8-00819S-XSA_101-111_EDIT
6/9/05
2:58 PM
Page 103
Renaming a Playlist Entry
Follow these instructions to rename a playlist entry, i.e.
to edit the title of a playlist entry.
3
Press the …† buttons to select Rename, then press
the OK or √ button.
The Rename screen is displayed.
(VR mode)
Rename
HDD
1 8 / JAN / 2005 12:15 PR 7
Using the PLAY LIST button
Back Space
1
With the unit in Stop mode/Playback mode, press the
PLAY LIST button.
The Edit Playlist screen is displayed.
Playlist
HDD
No.
001
002
003
004
Title
Length
16/JAN/2005 12:15P
19/JAN/2005 12:15P
22/JAN/2005 12:15P
25/JAN/2005 12:15P
MOVE
4
Space Delete
SELECT
Clear
Save
RETURN
EXIT
Select the desired characters using the …† œ √
buttons, then press the OK button.
00:10:21
00:40:03
00:20:15
00:50:16
Rename
16/JAN/2005 12:15 PR 7
HDD
16/JAN/2005 12:15
Dolphin
7 Scenes
1/1 Page
MOVE
SELECT
RETURN
EXIT
Back Space
Using the MENU button.
MOVE
• With the unit in Stop mode/Playback mode,
press the MENU button.
Space Delete
SELECT
Clear
Save
RETURN
EXIT
• This function is the same as the Rename function in
the renaming the title. (See page 94)
• The maximum number of characters that can be
entered is 31. All 31 characters can be displayed
by pressing the INFO button.
• Press the …† buttons to select Title,
then press the OK or √ button twice.
The Title List screen is displayed.
• Press the ANYKEY button.
• Press the …† buttons to select Playlist, then press
the OK or √ button.
• Press the …† buttons to select Go To Playlist,
then press the OK or √ button.
Press the …† buttons to select the title you want to
Rename from the Playlist, then press the ANYKEY
button.
ANYKEY menu is displayed : Rename, Copy, Delete,
Edit Playlist, Go To Titlelist, Disc Manager
Press the …† œ √ buttons to select Save, then press
the OK button.
The changed title is displayed in the title field of the
selected playlist entry.
Playlist
HDD
No.
001
002
003
004
Title
Length
00:10:21
19/JAN/2005 12:15P 00:40:03
22/JAN/2005 12:15P 00:20:15
25/JAN/2005 12:15P 00:50:16
Dolphin
Dolphin
16/JAN/2005 12:15
Playlist
HDD
No.
001
002
003
004
Rename
Copy
Title
16/JAN/2005 12:15P
19/JAN/2005 12:15P
22/JAN/2005 12:15P
25/JAN/2005 12:15P
7 Scenes
1/1 Page
Length
00:10:21
00:40:03
00:20:15
00:50:16
MOVE
SELECT
RETURN
EXIT
Delete
16/JAN/2005 12:15PR 7
Edit Playlist
16/JAN/2005 12:15
Go To Titlelist
7 Scenes
1/1 Page
Disc Manager
MOVE
SELECT
RETURN
EXIT
English - 103
Editing
2
5
8-00819S-XSA_101-111_EDIT
6/9/05
2:58 PM
Page 104
Editing a Scene for the Playlist
Follow these instructions to edit scenes for a playlist.
3
Press the …† buttons to select Edit Playlist,
then press the OK or √ button.
The Edit Scene screen is displayed.
(VR mode)
Edit Playlist
HDD
Playlist No. 1
Using the PLAY LIST button
1
01
00:00:26
02
0:00:07
05
0:00:26
06
00:01:07
03
00:06:04
04
0:00:03
1/1 Page
With the unit in Stop mode/Playback mode, press the
PLAY LIST button.
The Edit Playlist screen is displayed.
MOVE
Return
SELECT
RETURN
EXIT
Playlist
HDD
No.
001
002
003
004
Title
Length
16/JAN/2005 12:15P
19/JAN/2005 12:15P
22/JAN/2005 12:15P
25/JAN/2005 12:15P
00:10:21
00:40:03
00:20:15
00:50:16
4
16/JAN/2005 12:15 PR 7
16/JAN/2005 12:15
7 Scenes
1/1 Page
MOVE
SELECT
Playing a Selected Scene
RETURN
Press the …†œ √ buttons to select the scene you
want to play, then press the ANYKEY button.
The playlist entry to be played is selected.
EXIT
Using the MENU button.
Edit Playlist
HDD
• With the unit in Stop mode/Playback mode,
press the MENU button.
01
• Press the …† buttons to select Title,
Editing
2
Press the …† buttons to select the title you want to
edit from the Playlist, then press the ANYKEY button.
The Edit Playlist menu is displayed: Rename, Copy,
Delete, Edit Playlist, Go To Titlelist, Disc Manager.
02
0:00:07
06
00:01:07
03
00:06:04
04
0:00:03
Modify
Move
then press the OK or √ button twice.
The Title List screen is displayed.
• Press the ANYKEY button.
• Press the …† buttons to select Playlist, then press
the OK or √ button.
• Press the …† buttons to select Go To Playlist,
then press the OK or √ button.
0:00:26
Play
Playlist No. 1
05
Add0:00:26
Delete
1/1 Page
MOVE
5
SELECT
Return
RETURN
EXIT
Press the …† buttons to select Play, then press the
OK or √ button.
The selected scene is played.
√ Play
Playlist
HDD
No.
001
002
003
004
Rename
Copy
Title
16/JAN/2005 12:15P
19/JAN/2005 12:15P
22/JAN/2005 12:15P
25/JAN/2005 12:15P
Length
00:10:21
00:40:03
00:20:15
00:50:16
Delete
16/JAN/2005 12:15PR 7
Edit Playlist
• To stop scene play, press the STOP (
16/JAN/2005 12:15
Go To Titlelist
7 Scenes
1/1 Page
Disc Manager
MOVE
104 - English
SELECT
RETURN
EXIT
) button.
8-00819S-XSA_101-111_EDIT
6/9/05
2:58 PM
Page 105
Modifying a Scene (Replacing a Scene)
7
Press the OK button at the end point of the scene.
To setup, follow steps 1 to 3 in page 104.
Modify Scene
HDD
4
16/JAN/2005 12:15
Press the …† œ √ buttons to select the scene you
want to modify, then press the ANYKEY button.
Scene No. 001
Title List 1/9
Start
End
00:00:20
00:00:30
00:00:30
Edit Playlist
HDD
Start
End
Change
MOVE
01
Cancel
Playlist No. 1
0:00:26
Play
02
0:00:07
06
00:01:07
03
00:06:04
04
SELECT
RETURN
EXIT
0:00:03
Modify
Move
05
Add0:00:26
Delete
1/1 Page
MOVE
• The image and ending point time are displayed in the
End window.
Return
SELECT
RETURN
EXIT
8
5
Press the œ √ buttons to select Change, then press
the OK button.
Press the …† buttons to select Modify, then press the
OK or √ button.
The Modify Scene screen is displayed.
Edit Playlist
HDD
Playlist No. 1
01
0:00:26
02
0:00:07
05
0:00:26
06
00:01:07
03
00:00:04
04
0:00:03
Modify Scene
HDD
16/JAN/2005 12:15
1/1 Page
Scene No. 001
Title List 1/9
Start
End
00:00:00
00:00:00
MOVE
00:00:20
End
Start
Change
MOVE
6
Cancel
SELECT
RETURN
SELECT
Return
RETURN
EXIT
• The scene you want to modify is changed with the
selected section.
EXIT
Press the OK button at the start point of the scene.
Modify Scene
HDD
16/JAN/2005 12:15
Editing
Scene No. 001
Title List 1/9
Start
End
00:00:20
00:00:00
00:00:20
Start
End
Change
MOVE
Cancel
SELECT
RETURN
EXIT
• The image and starting point time are
displayed on the Start window.
• Select the starting or ending point of the
section you want to modify using the playback
related buttons (PLAY( ), SEARCH (
)).
English - 105
8-00819S-XSA_101-111_EDIT
6/9/05
3:02 PM
Page 106
Moving a Scene (Changing the Position of a Scene)
6
To setup, follow steps 1 to 3 in page 104.
Press the …† œ √ buttons to select the position
to which you want to move the selected scene,
then select the OK button.
Edit Playlist
4
Press the …† œ √ buttons to select the scene you
want to move (change the position), then press the
ANYKEY button.
HDD
Edit Playlist
HDD
Playlist No. 1
01
00:00:26
02
00:00:07
01
00:00:26
02
00:00:07
0:00:26
Play
02
0:00:07
06
00:01:07
03
00:06:04
04
00:00:04
04
1/1 Page
Playlist No. 1
MOVE
01
03
SELECT
00:00:03
Cancel
RETURN
EXIT
0:00:03
Modify
Move
05
Add0:00:26
Delete
1/1 Page
MOVE
• The selected scene is moved to the selected
position.
Return
SELECT
RETURN
EXIT
Edit Playlist
HDD
5
Press the …† buttons to select Move, then press the
OK or √ button.
Playlist No. 1
01
00:01:07
02
00:00:07
05
00:00:26
06
00:00:26
Playlist No. 1
01
00:00:26
02
00:00:07
05
00:00:26
06
00:01:07
03
00:00:04
04
1/1 Page
MOVE
SELECT
MOVE
SELECT
00:00:03
Return
RETURN
EXIT
Cancel
RETURN
EXIT
■
You cannot move the selected scene to
the position of the next scene, because
the selected scene should be inserted
before that position, which requires no
action.
■
Depending on the kind of disc, the
displayed screen may have a slight
difference.
• A yellow selection window is displayed on the
scene to be moved.
Editing
04
00:00:03
NOTE
106 - English
00:00:04
1/1 Page
Edit Playlist
HDD
03
8-00819S-XSA_101-111_EDIT
6/9/05
3:02 PM
Page 107
7
Adding a Scene
Press the OK button at the end point of the scene.
Add Scene
To setup, follow steps 1 to 3 in page 104.
HDD
16/JAN/2005 12:15
Scene No. 001
4
Press the …† œ √ buttons to select the scene that
will have a new scene inserted before it, then press
the ANYKEY button.
Title List : 1/7
Start
End
00:00:15
00:00:35
00:00:35
Start
End
Add
Cancel
MOVE
SELECT
RETURN
EXIT
Edit Playlist
HDD
01
Playlist No. 1
0:00:26
Play
02
0:00:07
03
02
00:00:07
00:00:04
04
• The image and time of the end point are displayed in
the End window.
• To cancel, press the œ √ buttons to select Cancel,
then press the OK button.
0:00:03
Modify
Move
01
Add0:00:26
Delete
1/1 Page
MOVE
SELECT
Return
RETURN
EXIT
8
5
Press the œ √ buttons to select Add, then press the OK
button.
Press the …† buttons to select Add, then press the
OK or √ button.
The Add Scene screen is displayed.
Edit Playlist
HDD
Playlist No. 1
01
00:00:26
02
00:00:07
03
01
00:00:26
02
00:00:07
02
00:00:04
04
00:00:03
Add Scene
HDD
16/JAN/2005 12:15
Scene No. 001
Start
MOVE
00:00:00
Title List : 1/7
00:02:17
1/1 Page
Return
End
SELECT
RETURN
EXIT
00:00:00
00:00:00
End
Start
Add
MOVE
6
Cancel
SELECT
RETURN
EXIT
• The section you want to add is inserted prior to the
scene selected in step 4 of Adding a Scene on the
previous page.
Press the OK button at the starting point of the scene.
Add Scene
HDD
16/JAN/2005 12:15
Editing
Scene No. 001
Title List : 1/7
Start
End
00:00:15
00:00:00
00:00:15
Start
End
MOVE
Add
Cancel
SELECT
RETURN
EXIT
• The image and starting point time are displayed
on the Start window.
• Select the starting or ending point of the
section you want to modify using the playback
related buttons (PLAY( ), SKIP (
)).
English - 107
8-00819S-XSA_101-111_EDIT
6/9/05
3:03 PM
Page 108
Deleting a Scene
Deleting a Playlist Entry from the
Playlist
To setup, follow steps 1 to 3 in page 104.
4
Using the PLAY LIST button
Press the …† œ √ buttons to select the scene you
want to delete, then press the ANYKEY button.
Edit Playlist
HDD
01
Playlist No. 1
0:00:26
02
Play
0:00:07
03
00:06:04
04
1
With the unit in Stop mode/Playback mode, press the
PLAY LIST button.
The Edit Playlist screen is displayed.
0:00:03
Playlist
Modify
HDD
Move
05
Add0:00:26
06
00:01:07
Delete
1/1 Page
MOVE
Return
SELECT
RETURN
EXIT
No.
Title
Length
001
002
003
004
16/JAN/2005 12:15
19/JAN/2005 12:15
22/JAN/2005 12:15
25/JAN/2005 12:15
00:10:21
00:40:03
00:20:15
00:50:16
16/JAN/2005 12:15
16/JAN/2005 12:15
7 Scenes
5
1/1 Page
MOVE
Press the …† buttons to select Delete, then press
the OK or √ button.
SELECT
RETURN
EXIT
Using the MENU button.
• With the unit in Stop mode/Playback mode,
press the MENU button.
Edit Playlist
HDD
01
Playlist No. 1
the scene
0:00:26 Do02you want
0:00:07 to delete
03
00:06:04
04
Yes
05
0:00:26
06
then press the OK or √ button twice.
The Title List screen is displayed.
No
00:01:07
1/1 Page
MOVE
• Press the …† buttons to select Title,
? 0:00:03
SELECT
• Press the ANYKEY button.
Return
RETURN
EXIT
• Press the …† buttons to select Playlist, then press
the OK or √ button.
• The message “Do you want to delete the scene ?” is
displayed.
Press the œ √ buttons to select Yes,
then press the OK to delete the selected scene.
Editing
6
• Press the …† buttons to select Go To Playlist,
then press the OK or √ button.
2
Press the …† buttons to select the title you want to
edit from the Playlist, then press the ANYKEY button.
The Edit Playlist menu is displayed:Rename, Copy,
Delete, Edit Playlist, Go To Titlelist, Disc Manager.
Playlist
HDD
No.
001
002
003
004
Rename
Copy
Title
16/JAN/2005 12:15P
19/JAN/2005 12:15P
22/JAN/2005 12:15P
25/JAN/2005 12:15P
Length
00:10:21
00:40:03
00:20:15
00:50:16
Delete
16/JAN/2005 12:15PR 7
Edit Playlist
16/JAN/2005 12:15
Go to Titlelist
7 Scenes
1/1 Page
Disc Manager
MOVE
108 - English
SELECT
RETURN
EXIT
8-00819S-XSA_101-111_EDIT
3
6/9/05
3:03 PM
Page 109
Press the …† buttons to select Delete, then press
the OK or √ button.
• You will be prompted with the delete confirmation
message “Do you want to delete?”.
Copying from HDD to
DVD
Playlist
HDD
About the Copy Screen
Do you want to delete?
16/JAN/2005 12:15 PR 7
16/JAN/2005 12:15
Yes
Copy
No
7 Scenes
Copy To : HDD ➞ DVD
HDD
MOVE
SELECT
RETURN
EXIT
!
@
No.
1
Title
Rec.Mode
01/JAN/2005 20:25A SP ➞ HS
Add a list
Length
00:01:40
#
$
4
Press the œ √ buttons to select Yes, then press the
OK button.
You automatically returned to the Playlist screen after
the delete operation has finished.
Start
Rec. Mode
[DVD] Available
SP 02:00:32
4.48 GB
Total
00:01:40
0.05 GB
MOVE
SELECT
RETURN
%
^
&
*
EXIT
! Title to be copied
@ Add titles to be copied (up to 7 titles can be copied
at one time)
# Recording mode for copying
Playlist
HDD
Deleting...
(Please wait)
$
%
^
&
16/JAN/2005 12:15 PR 7
16/JAN/2005 12:15
7 Scenes
*
Playlist
HDD
No.
Title
001 19/JAN/2005 12:15
002 22/JAN/2005 12:15
003 25/JAN/2005 12:15
- HS(high speed): you can copy more quickely than
normal playback speed.
Copies in the same record mode as source title.
- XP/SP/LP/EP : you can not use high speed copy.
Record time of title to be copied
Copy start button
Record mode setup button
Remaining time and space on the current disc in
DVD Record mode
Total record time and space of selected titles for
copying
Length
00:40:03
00:20:15
00:50:16
Contents Copy Specifications
19/JAN/2005 12:15
19/JAN/2005 12:15
7 Scenes
1/1 Page
MOVE
SELECT
RETURN
EXIT
Contents
Recorded Video Title
Copy Protected Title
Once "Copy Once programme" has been recorded on the
DVD disc, this title cannot be copied to HDD anymore.
But "Copy Once programme" has been recorded on the
HDD, this title can be copied to DVD-RW(VR mode) or
DVD-RAM.
English - 109
Editing
Copy Once Title
HDD ➞ DVD
Supported
Not supported
Move
(Deletes the Title in the HDD after copying)
8-00819S-XSA_101-111_EDIT
6/9/05
3:03 PM
Page 110
Using the TITLE LIST button
6
Press the ANYKEY button.
Title List
1
Press the OPEN/CLOSE button and place a
recordable disc on the disc tray.
HDD
Rename
No.
Protection
001
002
003
004
Copy
Delete
Edit
√
Playlist
√
Navigation
√
19/JAN/2005 12:15PR 7
2
Press the OPEN/CLOSE button to close the disc
tray. Wait until LOAD disappears from the front panel
display. Check that the disc has enough available
space for the recording.
3
Select the HDD by pressing the HDD button on the
front panel of the HDD & DVD RECORDER or on the
remote control.
4
With the unit in Stop mode/Playback mode, press the
TITLE LIST button.
The Title List screen is displayed.
19/JAN/2005 12:15
Title
√
Select Media
SP V-Mode Compatibility
Disc Manager
MOVE
7
1/1 Page
SELECT
RETURN
Copy
Title
Rec.Mode
18/JAN/2005 12:15A LP ➞ HS
Add a list
Length
00:10:21
Title
18/JAN/2005 12:15P
19/JAN/2005 12:15P
20/JAN/2005 12:15P
25/JAN/2005 12:15P
Start
Rec. Mode
Title List
No.
EXIT
Copy To : HDD ➞ DVD
HDD
1
001
002
003
004
00:10:21
00:40:03
00:20:15
00:50:16
Press the …† buttons to select Copy, then press the
OK or √ button.
Copy screen is displayed.
No.
HDD
Length
18/JAN/2005 12:15P
19/JAN/2005 12:15P
20/JAN/2005 12:15P
25/JAN/2005 12:15P
[DVD] Available
LP 04:00:16
Length
4.48 GB
00:10:21
00:40:03
00:20:15
00:50:16
Total
00:10:21
0.25 GB
MOVE
SELECT
RETURN
EXIT
18/JAN/2005 12:15 PR 7
18/JAN/2005 12:15
SP
V-Mode Compatibility
MOVE
1/1 Page
SELECT
RETURN
• If you want to change the record mode when copying,
see page 115.
EXIT
Using the MENU button.
• With the unit in Stop mode/Playback mode,
press the MENU button.
8
Press the OK or √ button to select Start,
then press the OK button.
• Press the …† buttons to select Title,
then press the OK or √ button twice.
The Title List screen is displayed.
Copy
No.
Editing
5
Press the …† buttons to select the title you want to
copy.
To move to other pages, press the SKIP(
buttons.
SKIP( ) : previous page of title list
SKIP( ) : next page of title list
Copy To : HDD ➞ DVD
HDD
1
Title
Rec.Mode
18/JAN/2005 12:15A LP ➞ HS
Add a list
Length
00:10:21
Start
Rec. Mode
[DVD] Available
LP 04:00:16
4.48 GB
)
Total
00:10:21
0.25 GB
MOVE
SELECT
RETURN
EXIT
- About Using COPY button Press the …† buttons to select title you want to
copy from the title list and then press the COPY
button on the remote control. You can go to copy
screen.
• During the Playback, you can also copy the title
by pressing the COPY button.
110 - English
8-00819S-XSA_101-111_EDIT
6/9/05
3:03 PM
Page 111
- Copying a Title that has been edited
once before -
9
The “Do you want to view screen of copying title?”
message is displayed.
-1 To begin high speed copy, press the œ √ buttons to
select Yes, then press the OK button.
High speed copy begins. The title to be copied is not
played back, while the currently broadcasting
programme is displayed on the screen.
10
Copy
Copy To : HDD ➞ DVD
HDD
No.
1
Title
Rec.Mode
Length
18/JAN/2005 12:15A LP ➞ HS 00:10:21
Start
Do you want
view screen of copying title?
Add to
a list
Rec. Mode
Yes
No
[DVD] Available
LP
04: 08:47
Total
04: 08:47
MOVE
SELECT
RETURN
EXIT
HDD
1%
DVD
If you want to stop copy, press CANCEL key.
10
To copy a title while viewing the title on the copy
screen, press the œ √ buttons to select Yes, then
press the OK button.
HDD
1%
DVD
• If No is selected, the title to be copied is displayed at
its playback speed while copying.
• To cancel the copying in progress, press the
CANCEL button.
-1 After a successful copy, “The title is successfully
copied” message is displayed.
11
If you want to stop copy, press CANCEL key.
• If No is selected, the title to be copied is not displayed
screen, and copying begins while the currently
broadcasting programme is displayed on the screen.
• To cancel the copying in progress, press the
CANCEL button.
The title is successfully copied.
- Copying an Unedited title -1 The “Do you want to use high speed copy mode?”
message is displayed.
Editing
9
Copy
Copy To : HDD ➞ DVD
HDD
No.
1
Title
Rec.Mode
Length
18/JAN/2005 12:15A LP ➞ HS 00:10:21
Start
Do you want
use high speed copy mode?
Add to
a list
Rec. Mode
Yes
No
[DVD] Available
LP
04: 08:47
Total
04: 08:47
MOVE
■
NOTE
SELECT
RETURN
EXIT
High speed copy : This means that you
can transfer without having to worry about
the quality getting worse with each copy
‘generation’. It also means that copying
can be carried out at the maximum speed
possible.
English - 111
9-00819S-XSA_112-125_EDIT
6/9/05
3:08 PM
Page 112
Changing the Record Mode
To setup, follow steps 1 to 7 in page 110.
8
Press the √ and † buttons to select Rec. Mode, then
press the OK button.
Copying Multiple Titles
at One Time
Copy
No.
1
Using the TITLE LIST button
Copy To : HDD ➞ DVD
HDD
Title
Rec.Mode
18/JAN/2005 12:15A LP ➞ HS
Add a list
Length
00:10:21
Start
Rec. Mode
XPAvailable
[DVD]
LPSP 04: 08:47
LP
EP Total
High 04:
Speed
08:47
MOVE
9
SELECT
RETURN
Press the OPEN/CLOSE button and place a
recordable disc on the disc tray.
2
Press the OPEN/CLOSE button to close the disc
tray. Wait until LOAD disappears from the front panel
display. Check that the disc has enough available
space for the recording.
3
Select the HDD by pressing the HDD button on the
front panel of the HDD & DVD RECORDER or on the
remote control.
4
With the unit in Stop mode/Playback mode, press the
TITLE LIST button.
The Title List screen is displayed.
EXIT
Press the …† buttons to select record mode you want
to record, then press the OK button.
• HS(High Speed) : Copies in the same record mode as
HDD.
• XP/SP/LP/EP : You cannot copy the higher quality
mode than original. If the same record mode is
selected, the title is copied at high speed.
■
NOTE
■
■
■
Editing
1
■
Title List
Using the same method, you can copy a
Playlist.
High speed copying is not available for a title
list that has been deleted partially.
During copying, timer recording is not
available.
High speed copying is not available when:
- Copying a title that can only be copied once
- Copying a playlist
- Copying a partially-deleted title
Regarding title lists that can be copied only
once:
- Only available for DVD discs that support
CPRM
- If a playlist contains a scene that can only be
copied once, it cannot be copied.
HDD
001
002
003
004
Title
18/JAN/2005 12:15P
19/JAN/2005 12:15P
20/JAN/2005 12:15P
25/JAN/2005 12:15P
Length
00:10:21
00:40:03
00:20:15
00:50:16
18/JAN/2005 12:15 PR 7
18/JAN/2005 12:15
SP
V-Mode Compatibility
MOVE
1/1 Page
SELECT
RETURN
EXIT
Using the MENU button.
• With the unit in Stop mode/Playback mode,
press the MENU button.
• Press the …† buttons to select Title,
then press the OK or √ button twice.
The Title List screen is displayed.
5
112 - English
No.
Press the …† buttons to select the title you want to
copy.
)
To move to other pages, press the SKIP (
buttons.
SKIP( ) : previous page of title list
SKIP( ) : next page of title list
9-00819S-XSA_112-125_EDIT
6
6/9/05
3:08 PM
Page 113
9
Press the ANYKEY button.
Title List
HDD
Rename
No.
Protection
001
002
003
004
Copy
Delete
Edit
√
Playlist
√
19/JAN/2005 12:15PR 7
Title
√
Navigation
19/JAN/2005 12:15
√
Select Media
SP V-Mode Compatibility
Disc Manager
MOVE
Length
18/JAN/2005 12:15P
19/JAN/2005 12:15P
20/JAN/2005 12:15P
25/JAN/2005 12:15P
00:10:21
00:40:03
00:20:15
00:50:16
Press the …† buttons to select Add, then press the OK
button.
Add Copy List screen is displayed.
Press the …† buttons to select you want to copy, then
press the OK button.
Other method: Press the …† buttons to select Add a
list, then press the OK button.
Press the …† buttons to select you want to copy, then
press the OK button.
1/1 Page
SELECT
RETURN
EXIT
Add Copy List
HDD
7
No.
001
002
003
004
Press the …† buttons to select Copy, then press the
OK or √ button.
Copy screen is displayed.
Title
Length
18/JAN/2005 12:15P
19/JAN/2005 12:15P
20/JAN/2005 12:15P
25/JAN/2005 12:15P
00:10:21
00:40:03
00:20:15
00:50:16
18/JAN/2005 12:15 PR 7
18/JAN/2005 12:15
SP
V-Mode Compatibility
MOVE
1/1 Page
SELECT
RETURN
EXIT
Copy
Copy To : HDD ➞ DVD
HDD
No.
Title
Rec.Mode
18/JAN/2005 12:15A LP ➞ HS
Add a list
1
10
Length
00:10:21
Start
Rec. Mode
[DVD] Available
LP 04:00:16
Press the …† buttons to select an additional title
you want to copy, then press the OK button.
Repeat steps 8~10 to select a title you want to copy.
4.48 GB
Total
00:10:21
0.25 GB
MOVE
SELECT
RETURN
Copy
No.
1
2
3
8
Copy To : HDD ➞ DVD
HDD
EXIT
Title
Rec.Mode
18/JAN/2005 12:15A LP ➞ HS
19/JAN/2005 13:15A LP ➞ HS
20/JAN/2005 15:15A LP ➞ HS
Add a list
Length
00:10:21
00:15:21
00:30:21
Press the ANYKEY button.
Start
Rec. Mode
[DVD] Available
LP 04:00:16
4.48 GB
Total
00:56:03
1.88 GB
MOVE
SELECT
RETURN
EXIT
Copy
Copy To : HDD ➞ DVD
HDD
No.
1
Title
Rec.Mode
18/JAN/2005 12:15A LP ➞ HS
Add a list
Length
00:10:21
Start
Rec. Mode
[DVD] Available
LP 04:00:16
Add
Delete
11
Press the OK or √ buttons to select Start,
then press the OK button.
4.48 GB
Total
Preview
00:10:21
0.25 GB
√
Rec. Mode
MOVE
SELECT
RETURN
Copy
Copy To : HDD ➞ DVD
HDD
EXIT
No.
Title
Rec.Mode
18/JAN/2005 12:15A LP ➞ HS
19/JAN/2005 13:15A LP ➞ HS
20/JAN/2005 15:15A LP ➞ HS
Add a list
Length
00:10:21
00:15:21
00:30:21
Start
Rec. Mode
[DVD] Available
LP 04:00:16
4.48 GB
Total
00:56:03
1.88 GB
MOVE
SELECT
RETURN
EXIT
The added title lists into the copy list are copied.
To cancel the copying in progress, press the CANCEL
button.
■
NOTE
If copy list contains at least one title that
cannot be copied at high speed, it performs
the step 9 described on page 111.
Otherwise, it performs the step 9-1 described
on page 111.
English - 113
Editing
1
2
3
9-00819S-XSA_112-125_EDIT
6/9/05
3:08 PM
Page 114
Deleting an Undesired Title from the
Copy List
To setup, follow steps 1 to 7 in pages 112~113.
8
Press the …† buttons to select a title you want to
delete from the copy screen.
Previewing a Selected Title from the
Copy List
To setup, follow steps 1 to 7 in pages 112~113.
8
Press the …† buttons to select a title you want to
preview in the copy screen.
Copy
Copy
No.
1
2
3
Title
Rec.Mode
18/JAN/2005 12:15A LP ➞ HS
19/JAN/2005 13:15A LP ➞ HS
20/JAN/2005 15:15A LP ➞ HS
Add a list
No.
Length
00:10:21
00:15:21
00:30:21
Copy To : HDD ➞ DVD
HDD
Copy To : HDD ➞ DVD
HDD
1
2
3
Start
Rec. Mode
[DVD] Available
LP 04:00:16
Title
Rec.Mode
18/JAN/2005 12:15A LP ➞ HS
19/JAN/2005 13:15A SP ➞ LS
20/JAN/2005 15:15A SP ➞ HS
Add a list
Length
00:10:21
00:15:21
00:30:21
Start
Rec. Mode
[DVD] Available
LP 04:00:16
4.48 GB
4.48 GB
Total
Total
00:56:03
1.88 GB
00:56:03
1.88 GB
MOVE
9
SELECT
RETURN
MOVE
EXIT
Press the ANYKEY button. Press the …† buttons to
select Delete, then press the OK or √ button.
The message “Do you want to delete?” is displayed.
9
SELECT
RETURN
EXIT
Press the ANYKEY button. Press the …† buttons to
select Preview, then press the OK or √ button.
You can preview the selected title through the display
window located at the centre of the screen.
Copy
Copy To : HDD ➞ DVD
HDD
No.
1
2
3
Title
Rec.Mode
Copy
Length
HDD
18/JAN/2005 12:15A LP ➞ HS 00:10:21
Do youLPwant
19/JAN/2005 13:15A
➞ HS to delete?
00:15:21
20/JAN/2005 15:15A LP ➞ HS 00:30:21
Add a list
Yes
No
Copy To : HDD ➞ DVD
Start
No.
Rec. Mode
1
2
3
[DVD] Available
LP 04:00:16
4.48 GB
Total
Title
Rec.Mode
18/JAN/2005 12:15A LP ➞ HS
19/JAN/2005 13:15A SP ➞ LS
20/JAN/2005 15:15A SP ➞ HS
Add a list
Length
00:10:21
00:15:21
00:30:21
01:06:03
1.88 GB
MOVE
SELECT
RETURN
4.48 GB
Total
00:56:03
1.88 GB
EXIT
SELECT
Editing
10
Press the œ √ buttons to select Yes, then press the
OK button.
The selected title is deleted.
Copy
Copy To : HDD ➞ DVD
HDD
No.
Title
Rec.Mode
Length
1
3
19/JAN/2005 13:15A
20/JAN/2005 15:15A
LP ➞ HS
LP ➞ HS
00:15:21
00:30:21
Add a list
Start
Rec. Mode
[DVD] Available
LP 04:00:16
4.48 GB
Total
00:45:42
1.30 GB
MOVE
114 - English
SELECT
RETURN
Start
Rec. Mode
[DVD] Available
LP 04:00:16
EXIT
10
RETURN
EXIT
Press the RETURN button to exit the Preview mode.
9-00819S-XSA_112-125_EDIT
6/9/05
3:08 PM
Page 115
Selecting Record Mode of Each
Title from the Copy List
Changing Record Mode of All Titles
from the Copy List
You can copy multiple titles while setting different record
You can copy multiple titles while setting the same record
modes for each title.
mode for all titles.
To setup, follow steps 1 to 7 in pages 112~113.
To setup, follow steps 1 to 7 in pages 112~113.
8
Press the …† buttons to select a title to change its
record mode in the copy screen.
8
Select the Rec. Mode on the right-hand side on the
screen using the …†œ √ buttons, then press the
OK button.
Copy
No.
1
2
3
Copy
Copy To : HDD ➞ DVD
HDD
Title
Rec.Mode
18/JAN/2005 12:15A LP ➞ HS
19/JAN/2005 13:15A SP ➞ LS
20/JAN/2005 15:15A SP ➞ HS
Add a list
Length
00:10:21
00:15:21
00:30:21
Copy To : HDD ➞ DVD
HDD
No.
Start
1
2
3
Rec. Mode
[DVD] Available
LP 04:00:16
Title
Rec.Mode
18/JAN/2005 12:15A LP ➞ HS
19/JAN/2005 13:15A SP ➞ LS
20/JAN/2005 15:15A SP ➞ HS
Add a list
Length
00:10:21
00:15:21
00:30:21
4.48 GB
Total
00:56:03
1.88 GB
MOVE
9
SELECT
RETURN
Copy
1
2
3
01:06:03
MOVE
9
SELECT
RETURN
EXIT
Press the …† buttons to select the record mode you
want, then press the OK button.
Rest of the copying process can be performed as
described in page 110 to 111.
Copy To : HDD ➞ DVD
HDD
No.
[DVD]
XP Available
LP
SP 04:00:16
LP 4.48 GB
Total
EP
High Speed
1.88 GB
EXIT
Press the ANYKEY button. Press the …† buttons to
select Rec. Mode, then press the OK or √ button.
Start
Rec. Mode
Rec.Mode
Length
18/JAN/2005 12:15A LP ➞ HS
19/JAN/2005 13:15A SP ➞ LS
20/JAN/2005 15:15A SP ➞ HS
Add
XP
Add a list
Delete
SP
Title
00:10:21
00:15:21
00:30:21
Preview
LP
√
Rec. Mode
MOVE
Start
4.48 GB
Total
00:56:03
1.88 GB
RETURN
EXIT
Copy To : HDD ➞ DVD
HDD
[DVD] Available
LP 04:00:16
EP
SELECT
Copy
Rec. Mode
No.
1
2
3
Title
Rec.Mode
18/JAN/2005 12:15A LP ➞ HS
19/JAN/2005 13:15A SP ➞ HS
20/JAN/2005 15:15A SP ➞ HS
Add a list
Length
00:10:21
00:15:21
00:30:21
Start
Rec. Mode
[DVD] Available
LP 04:00:16
4.48 GB
Total
00:56:03
1.88 GB
MOVE
11
Repeat steps 9~11 to select a title to change it’s
record mode.
Rest of the copying process can be performed as
described in page 110 to 111.
SELECT
RETURN
EXIT
Editing
10
Press the …† buttons to select the record mode you
want, then press the OK or √ button.
English - 115
9-00819S-XSA_112-125_EDIT
6/9/05
3:08 PM
Page 116
Copying from DVD to
HDD
4
Press the …† buttons to select the title you want to
copy.
)
To move to other pages, press the SKIP (
buttons.
SKIP( ) : previous page of title list
SKIP( ) : next page of title list
5
Press the ANYKEY button.
Using the TITLE LIST button
1
2
Press the OPEN/CLOSE button and place a
recordable disc on the disc tray.
Title List
DVD-RAM(VR)
Rename
No.
Protection
001
002
003
004
Copy
Press the OPEN/CLOSE button to close the disc tray.
Delete
Partial Delete
Playlist
√
Navigation
√
19/JAN/2005 12:15PR 7
19/JAN/2005 12:15
3
Title List
No.
001
002
003
004
Title
18/JAN/2005 12:15P
19/JAN/2005 12:15P
20/JAN/2005 12:15P
25/JAN/2005 12:15P
Length
00:10:21
00:40:03
00:20:15
00:50:16
MOVE
6
Length
18/JAN/2005 12:15P
19/JAN/2005 12:15P
20/JAN/2005 12:15P
25/JAN/2005 12:15P
√
Select Media
SP V-Mode Compatibility
Disc Manager
With the unit in Stop mode/Playback mode, press the
TITLE LIST button.
The Title List screen is displayed.
DVD-RAM(VR)
Title
1/1 Page
SELECT
RETURN
Copy
DVD-RAM(VR)
18/JAN/2005 12:15
V-Mode Compatibility
MOVE
EXIT
Press the …† buttons to select Copy, then press the
OK or √ button.
Copy screen is displayed.
18/JAN/2005 12:15 PR 7
SP
00:10:21
00:40:03
00:20:15
00:50:16
1/1 Page
SELECT
RETURN
No.
1
EXIT
Title
Copy To : DVD ➞ HDD
Rec.Mode
18/JAN/2005 12:15A LP ➞ HS
Add a list
Length
00:10:21
Start
[HDD] Available
LP 40:16:56
52.99 GB
Total
Using the MENU button.
00:10:21
0.25 GB
• With the unit in Stop mode/Playback mode,
press the MENU button.
MOVE
• Press the …† buttons to select Title,
then press the OK or √ button.
SELECT
RETURN
- About Using COPY button Press the …† buttons to select title you want to
copy from the title list and then press the COPY
button on the remote control. You can go to copy
screen.
• During the Playback, you can also copy the title
by pressing the COPY button.
Editing
• Press the …† buttons to select Title List,
then press the OK or √ button.
The Title List screen is displayed.
7
Press the OK or √ buttons to select Start, then press
the OK button.
DVD
1%
If you want to stop copy, press CANCEL key.
116 - English
EXIT
HDD
9-00819S-XSA_112-125_EDIT
8
6/9/05
3:08 PM
Page 117
After a successful copy, “The title is successfully copied.”
message is displayed.
Copying MP3 or JPEG
Files from a Disc to HDD
File Copy
The title is successfully copied
1
2
• Copying Multiple Titles at One Time – Same as an
HDD operation(See page 112)
Insert a JPEG disc or MP3 disc into the disc tray.
Press the OPEN/CLOSE button to close the disc tray.
Wait until LOAD disappears from the front panel display.
Check that the disc has enough available space for the
recording.
• Deleting an Undesired Title from the Copy List –
Same as an HDD operation(See page 114)
• Previewing a Selected Title from the Copy List –
Same as an HDD operation(See page 114)
3
Press the …† buttons to select Music or Photo, then
press the OK or √ button.
MP3 or JPEG file list is displayed.
Music List
CD
Bryan Adams.mp3
√ 02 : 10
..
■
NOTE
■
■
■
■
■
You cannot copy anything else on finalised
DVD-R and DVD-RW(V mode) mode.
You cannot copy a DVD-VIDEO to HDD.
Only video will be copied from title lists or
playlist that contains still images.
High speed copying from a DVD-RAM or
DVD-RW (VR mode) is available.
When you copy from DVD-RW(V mode)/-R
disc to HDD, high speed copy is not
available.
Record mode cannot be changed when
you copy a title from DVD to HDD.
Bryan Adams.mp3
MP3
01/15
4.0 MB
MP3
Bryan Adams_2.mp3
MP3
Straight from the heart.mp3
MP3
Run to you.mp3
MP3
Heaven.mp3
MP3
This Love.mp3
1/3 Page
MOVE
SELECT
RETURN
EXIT
Contents Copy Specifications
Editing
Contents
Recorded Video Title
Copy Protected Title
Copy Once Title
DVD ➞ HDD
Supported
Not supported
Not supported
English - 117
9-00819S-XSA_112-125_EDIT
6/9/05
3:10 PM
Page 118
Folder Copy
4
Press the …† buttons to select the MP3 or JPEG files
you want to copy, then press the ANYKEY button.
1
Insert a Disc (JPEG or MP3) in to the tray.
2
Press the …† buttons to select Music or Photo, then
press the OK or √ button.
MP3 or JPEG folder are displayed.
Music List
CD
» 02 : 10
Bryan Adams.mp3
..
Bryan Adams.mp3
Copy
Play Mode
√
MP3
Bryan Adams_2.mp3
MP3
Straight from the heart.mp3
MP3
Run to you.mp3
Go01/15
To Playlist
MP3
Heaven.mp3
New
4.0Playlist
MB
MP3
This Love.mp3
MUSIC
Select Media
MOVE
√
1/3 Page
SELECT
RETURN
EXIT
Music List
CD
00 : 00
..
Song1
Song2
Song3
5
Press the …† buttons to select Copy, then press the
OK or √ button.
File copy begins.
The copying of only 1 file cannot be cancelled.
When copying only 1 file from a disc to HDD, it is
located under the HDD’s Music or Photo folder.
Music List
CD
Bryan Adams.mp3
» 02 : 10
Song4
ROOT
Song5
01/15
__
1/1 Page
MOVE
3
MUSIC
Bryan Adams.mp3
Copying...
HDD
MP3 Bryan Adams_2.mp3
Disc Type : HDD
Free space : 2939 MB MP3 Straight from the heart.mp3
Total
file number : 1/1 MP3 Run to you.mp3
MUSIC
Heaven.mp3
MP3 Adams.mp3
Copying File Name : Bryan
This
43Love.mp3
%
SELECT
RETURN
EXIT
Press the …† buttons to select the MP3 or JPEG
folder you want to copy, then press the ANYKEY
button.
Music List
CD
00 : 00
..
1/3 Page
Song1
Song2
CANCEL
Song3
Copy
ROOT
Go To Playlist
01/15
New Playlist
__
Select Media
MOVE
Editing
4
Song4
Song5
√
1/1 Page
SELECT
RETURN
EXIT
Press the …† buttons to select Copy, then press the
OK or √ button.
Folder copy begins.
Subfolders and files in the selected folder are copied.
Music List
CD
Bryan Adams.mp3
» 02 : 10
MUSIC
Bryan Adams.mp3
HDD
MP3 Bryan Adams_2.mp3
Disc Type : HDD
Free space : 2939 MB MP3 Straight from the heart.mp3
Total
file number : 1/16 MP3 Run to you.mp3
MUSIC
Heaven.mp3
MP3 Adams.mp3
Copying File Name : Bryan
Copying...
This
43Love.mp3
%
1/3 Page
CANCEL
118 - English
9-00819S-XSA_112-125_EDIT
6/9/05
3:10 PM
Page 119
■
Pressing the CANCEL button during folder
copying will cancel the folder copying after
the current file is copied.
■
Up to 1,500 files and 1,000 subfolders can
be copied into one folder for MP3 files.
■
Up to 4,500 files and 1,000 subfolders can
be copied into one folder for JPEG files.
■
Files having an existing name of
***.mp3/***.jpg, is automatically renamed
to ***01.mp3/***01.jpg and copied.
NOTE
■
It allows up to 999 copies to have the
same name.
■
You cannot copy an Audio CD.
■
MP3 or JPEG files can be copied only
from a disc to the HDD.
■
The sizes of a file in a disc and the copied
one in the HDD may be slightly different
due to the file system.
Disc Manager
Editing the Disc Name
Follow these instructions to give a name to a disc.
1
With the unit in Stop mode, press the ANYKEY
button.
Search
Scene Navigation
Time Navigation
Marker
Contents Copy Specifications
Contents
MP3
JPEG(photo)
DivX
HDD ➞ DVD
Not supported
Not supported
Not supported
Rec. Mode
√
Select Madia
√
Disc Manager
DVD ➞ HDD
supported
supported
Not supported
2
Press the …† buttons to select Disc Manager, then
press the OK or √ button.
Disc Manager
DVD-RAM(VR)
Disc Name
Used Space
00 : 04 : 30
Available Space
02 : 08 SP
Disc Protection Info
Not Protected
Rename
Protection
MOVE
Delete All
SELECT
RETURN
Format
EXIT
Editing
English - 119
9-00819S-XSA_112-125_EDIT
6/9/05
3:10 PM
Page 120
Disc Protection
3
Press the œ √ buttons to select Rename, then press
the OK button.
The Rename screen is displayed.
Disc Protection allows you to protect your discs from
being formatted or deleted due to unintended
operations.
Rename
DVD-RAM(VR)
1
Back Space
Space Delete
MOVE
SELECT
Clear
RETURN
With the unit in Stop mode, press the ANYKEY
button.
Save
EXIT
Search
Scene Navigation
4
Time Navigation
Select the desired characters using the …† œ √
buttons, then press the OK button.
Marker
Rec. Mode
√
Select Madia
√
Disc Manager
Rename
DVD-RAM(VR)
Disc
Back Space
Space Delete
MOVE
SELECT
Clear
RETURN
Save
2
Press the …† buttons to select Disc Manager, then
press the OK or √ button.
EXIT
Disc Manager
DVD-RAM(VR)
Disc Name
5
Press the …† œ √ buttons to select Save,
then press the OK button.
A disc name is given to the disc.
Used Space
00 : 04 : 30
Available Space
02 : 03 SP
Disc Protection Info
Not Protected
Rename
Protection
MOVE
Delete All
SELECT
RETURN
Format
EXIT
Disc Manager
DVD-RAM(VR)
Disc Name
Disc
Used Space
00 : 04 : 30
Available Space
02 : 08 SP
Disc Protection Info
Not Protected
Rename
Protection
MOVE
3
Delete All
SELECT
RETURN
Press the œ √ buttons to select Protection, then press
the OK button.
Format
Disc Manager
EXIT
DVD-RAM(VR)
Editing
Disc Name
Used Space
Available Space
00 : 11 : 56
Disc Protection:
00 : 11 : 56 SP
On
Disc Protection Info
Rename
Protection
MOVE
■
You may need to clear disc protect before
beginning editing.
■
Depending on the kind of disc, the
displayed screen may be different.
NOTE
120 - English
4
Off
Not Protected
Delete All
SELECT
RETURN
Format
EXIT
Press the œ √ buttons to select On, then press the OK
button.
9-00819S-XSA_112-125_EDIT
6/9/05
3:10 PM
Page 121
Formatting a Disc
Use these instructions to format a disc.
The disc protect should also be cleared.
DVD-RW
• You will be prompted with the confirmation
message “Choose the recording format for
DVD- RW.”
Disc Manager
DVD-RW(VR)
Disc Name
1
With the unit in Stop mode, press the ANYKEY
button.
Used Space
00 : 10 : 32
Available Space
01 : 29 SP
Choose the recording format for DVD-RW.
Disc Protection Info Not Protected
Current Rec. ModeDVD-VR
VR-Mode
DVD-V
Rename
Protection
Delete All
MOVE
Search
Finalise
SELECT
Format
RETURN
EXIT
Scene Navigation
Time Navigation
Marker
Rec. Mode
√
Select Madia
√
Disc Manager
4
2
Press the …† buttons to select Disc Manager, then
press the OK or √ button.
Press the œ √ buttons to select Yes, then press the OK
button. The disc is formatted.
DVD-VR and DVD-V are defined according to their
recording format.
Disc Manager
HDD
[Title Partition]
Used Space
00 : 10 : 32
Available Space
35 : 47 : 10 SP
DISC
[Music/Photo Partition]
Used Space
0006MB
Available Space
DVD-V
DVD-RW
DVD-R
10034MB
Delete All
MOVE
3
DVD-VR
DVD-RAM
DVD-RW
SELECT
RETURN
Format
EXIT
Press the œ √ buttons to select Format, then press the
OK button.
Disc Manager
HDD
[Title Partition]
Used Space
00 : 10 : 32
Available Space
35 : 47 : 10 SP
Do you want to format this disc?
[Music/Photo Partition]
Used Space
0006MB
Yes
Available Space
No
10034MB
SELECT
RETURN
Editing
Delete All
MOVE
Format
EXIT
HDD/DVD-RAM
• You will be prompted with the confirmation
message “Do you want to format this disc?”.
• If you select Yes, you will be prompted with the
confirmation message “All data will be deleted.
Do you want to continue?”.
English - 121
9-00819S-XSA_112-125_EDIT
6/9/05
3:10 PM
Page 122
Delete All Title Lists/Music
Lists/Photo Lists
4
Press the œ √ buttons to select the Title, Music or
Photo, then press the OK button.
Title
Disc Manager
HDD
1
With the unit in Stop mode, press the ANYKEY
button.
[Title Partition]
Used Space
00 : 10 : 32
Available Space
35 : 47 : 10 SP
All title will be deleted.
[Music/Photo Partition]
Do you want to continue?
Used Space
0006MB
Available Space
Yes
No
10034MB
Delete All
MOVE
Search
SELECT
RETURN
Format
EXIT
Scene Navigation
Time Navigation
Marker
Rec. Mode
√
Select Madia
√
Music
Disc Manager
Disc Manager
HDD
2
[Title Partition]
Used Space
00 : 10 : 32
Available Space
35 : 47 : 10 SP
All music will be deleted.
Press the …† buttons to select Disc Manager, then
press the OK or √ button.
[Music/Photo Partition]
Do you want to continue?
Used Space
0006MB
Available Space
Yes
No
10034MB
Delete All
MOVE
SELECT
RETURN
Format
EXIT
Disc Manager
HDD
[Title Partition]
Used Space
00 : 10 : 32
Available Space
35 : 47 : 10 SP
Photo
[Music/Photo Partition]
Used Space
0006MB
Available Space
10034MB
Disc Manager
Delete All
MOVE
SELECT
HDD
Format
RETURN
[Title Partition]
Used Space
EXIT
00 : 10 : 32
Available Space
35 : 47 : 10 SP
All photo will be deleted.
[Music/Photo Partition]
Do you want to continue?
Used Space
0006MB
3
Available Space
Press the œ √ buttons to select Delete All, then press
the OK button.
Yes
No
10034MB
Delete All
MOVE
SELECT
RETURN
Format
EXIT
Disc Manager
Editing
HDD
[Title Partition]
Used Space
00 : 10 : 32
Available Space
35 : 47 : 10 SP
5
Select contents to delete all
[Music/Photo Partition]
Used Space
0006MB
Title
Available Space
Music
Photo
10034MB
Delete All
MOVE
SELECT
RETURN
Format
EXIT
• When Protected Entry exists: The Delete All Title List
function will not operate. If there is a title containing a
still picture, however, that function will not operate. If
you want to delete a protected entry, disable Protect
for it on the Lock item.
122 - English
Press the œ √ buttons to select Yes, then press the OK
button.
All title lists, music list or photo lists are deleted.
9-00819S-XSA_112-125_EDIT
6/9/05
3:10 PM
Page 123
• When Protected Entry exists: The Delete All Title List
function will not operate. If there is a title containing a
still picture, however, that function will not operate.
If you want to delete a protected entry, disable Protect
for it on the Lock item.
• When protected a DVD-RAM is used, data cannot be
deleted from a disc.
Delete All Title Lists
1
With the unit in Stop mode, press the ANYKEY
button.
4
Press the œ √ buttons to select Yes, then press the OK
button.
All title lists are deleted.
Search
Scene Navigation
Time Navigation
Marker
Rec. Mode
√
Select Madia
√
Disc Manager
2
Press the …† buttons to select Disc Manager, then
press the OK or √ button.
Disc Manager
DVD-RAM(VR)
Disc Name
Used Space
00 : 11 : 56
Available Space
00 : 11 : 56 SP
Disc Protection Info
Not Protected
Rename
Protection
MOVE
3
Delete All
SELECT
RETURN
Format
EXIT
Press the œ √ buttons to select Delete All, then press
the OK button.
• You will be prompted with the confirmation message
“Do you want to delete all title lists?”.
Editing
Disc Manager
DVD-RAM(VR)
Disc Name
00 : 11 : 56
Used Space
Do you want to00delete
allSPtitle lists?
: 11 : 56
Available Space
Yes
Disc Protection Info
Rename
No
Not Protected
Protection
MOVE
Delete All
SELECT
RETURN
Format
EXIT
English - 123
9-00819S-XSA_112-125_EDIT
6/9/05
3:10 PM
Page 124
If you select Yes, you will be prompted again with the
message “Disc will be finalised. Do you want to
continue?”.
Finalising a Disc
After you record titles onto a DVD-RW/DVD-R disc with
your HDD & DVD RECORDER, it needs to be finalised
before it can be played back on external devices.
Disc Manager
DVD-RW(VR)
Disc Name
00 : 10 : 32
Used Space
Available Space
01 : 29 SP
Disc will be finalised.
Do you want to continue?
Disc Protection Info Not Protected
Current Rec. Mode Yes
VR-Mode
1
With the unit in Stop mode, press the ANYKEY
button.
No
Rename
Protection
Delete All
MOVE
Finalise
SELECT
Format
RETURN
EXIT
Search
Scene Navigation
Time Navigation
4
Marker
Rec. Mode
√
Select Madia
√
Disc Manager
2
Press the …† buttons to select Disc Manager, then
press the OK or √ button.
Press the œ √ buttons to select Yes, then press the
OK button.
The disc is finalised.
■
Once a disc is finalised, you cannot delete
entries from the record list.
■
After being finalised, the DVD-R/DVDRW(video mode) operates in the same
manner as a DVD-Video.
■
Depending on the disc type, the displayed
screen may be different.
■
Finalising time may be different depending
on the amount of data recorded on the
disc.
■
Data on the disc will be damaged if the
recorder is powered off during finalise
process.
■
When the disc contains a music or JPEG
files, you cannot finalise the disc.
NOTE
Disc Manager
DVD-RW(VR)
Disc Name
Used Space
00 : 10 : 32
Available Space
01 : 29 SP
Disc Protection Info Not Protected
Current Rec. Mode VR-Mode
Rename
Protection
Delete All
MOVE
Editing
3
Finalise
SELECT
Format
RETURN
EXIT
Press the …† œ √ buttons to select Finalise, then
press the OK button.
You will be prompted with the message “Do you want to
finalise disc?”.
Disc Manager
DVD-RW(VR)
Disc Name
Used Space
00 : 10 : 32
Available Space
01 : 29 SP
Do you want to finalise disc?
Disc Protection Info Not Protected
Current Rec. Mode Yes
VR-Mode
No
Rename
Protection
Delete All
MOVE
124 - English
Finalise
SELECT
Format
RETURN
EXIT
9-00819S-XSA_112-125_EDIT
6/9/05
3:10 PM
Page 125
Unfinalising a Disc (V/VR mode)
4
Press the œ √ buttons to select Yes, then press the
OK button.
The disc is unfinalised.
■
1
With the unit in Stop mode, press the ANYKEY
button.
NOTE
A DVD-RW can be finalised or unfinalised
in Video mode.
Unfinalise
DVD-RW(V)
Additional recording, protection
Operation Same as DVD-Video
and deletion are possible.
Mark
Search
Scene Navigation
Finalise
DVD-Video(RW)
Time Navigation
Marker
√
Select Madia
■
Disc Manager
2
Press the …† buttons to select Disc Manager, then
press the OK or √ button.
A DVD-RW can be finalised or unfinalised
in VR mode.
Finalise
Unfinalise
Mark
DVD-RW(VR:F)
DVD-RW(VR)
Operation
Additional recording,
deletion, editing, and
protection are impossible.
Additional recording,
deletion, editing, and
protection are possible.
Disc Manager
DVD-RW(VR:F)
Disc Name
Used Space
00 : 00 : 00
Available Space
00 : 00 SP
Current Rec. Mode DVD-VR
unfinalise
MOVE
3
SELECT
RETURN
Format
EXIT
Press the œ √ buttons to select Unfinalise, then
press the OK button.
You will be prompted with the message “Do you want
to unfinalise disc?”.
Disc Manager
DVD-RW(VR:F)
Disc Name
Used Space
00 : 00 : 00
Available Space
00 : 00 SP
Do you want to unfinalise disc?
Current Rec. Mode DVD-V
No
unfinalise
MOVE
SELECT
RETURN
Editing
Yes
Format
EXIT
If you select Yes, you will be prompted again with the
message “Disc will be unfinalised. Do you want to
continue?”.
Disc Manager
DVD-RW(VR:F)
Disc Name
00 : 00 : 00
Used Space
Available Space
00 : 00 SP
Disc will be unfinalised.
Do you want to continue?
Current Rec. Mode DVD-V
Yes
No
unfinalise
MOVE
SELECT
RETURN
Format
EXIT
English - 125
10-00819S-XSA_126-131_Reference
6/9/05
1:57 PM
Reference
Page 126
Troubleshooting
If your product malfunctions, go through the
checkpoints below before contacting a Samsung
authorised service centre.
Power
The input is displayed for a while when the
power is turned on.
Checkpoint 1
The HDD & DVD RECORDER
requires some time to initialize and the
input will be displayed for approx. 10
seconds after it is turned on.
Recording
Cannot record TV programmes.
Checkpoint 1
Check whether the power cord is
securely plugged into the power outlet.
Checkpoint 2
Did you set the HDD & DVD
RECORDER channel settings correctly?
Checkpoint 3
Check the free space on your
HDD/DVD-RAM/-RW/-R discs.
Reference
I pressed the REC button but there is no response.
Checkpoint 1
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . .126
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . .130
126 - English
Recording is possible for HDD/DVDRAM/-RW/-R discs only.
If a programme is copy protected,
it cannot be recorded.
10-00819S-XSA_126-131_Reference
6/9/05
1:57 PM
Page 127
Playback
Cannot play the disc.
Checkpoint 1
Checkpoint 2
Checkpoint 3
Check whether the disc is inserted
correctly with the label facing up.
Checkpoint 1
Check the regional code of the DVD
disc.
The angle operation is available only
when the disc contains images
captured from different angles.
This HDD & DVD RECORDER cannot
play some types of discs.
(See pages 6, 44)
icon appears on the screen.
Checkpoint 1
The angle operation does not work while playing a
DVD disc.
You cannot use this operation or
function due to one of the following
reasons:
(1) Your DVD disc restricts it.
(2) Your DVD disc does not support
this feature (for example: angles)
(3) The feature is not available at the
moment.
(4) You've requested a title, chapter, or
scan time that is out of range.
The selected audio and/or subtitle language is not
played.
Checkpoint 1
Audio and subtitle languages are
disc-specific. Only the sound and
subtitle languages contained on the
DVD disc are available and displayed
in the disc menu.
Cannot copy title or file to the other mode.
Play mode settings are different from the settings
configured in the Settings menu.
Checkpoint 1
The disc does not support all selected
functions. In this case, some settings
configured in the settings menu may
not work properly.
Checkpoint 1
DVD discs encoded with copy
protection can not be copied to HDD.
Checkpoint 2
Refer to “Contents Copy Specifications”
on page 5 to check if copying is
supported.
Reference
Cannot change the aspect ratio.
Checkpoint 1
The aspect ratio is fixed for DVD
discs. (See pages 38~39)
English - 127
10-00819S-XSA_126-131_Reference
6/9/05
1:57 PM
Video
Timer Recording
The disc revolves, but no image or bad quality
images are displayed.
Checkpoint 1
Be sure that the Video Setting is
properly set. (See pages 38~39)
Checkpoint 2
Check whether there is damage to or
any foreign material on your disc.
Checkpoint 3
Checkpoint 4
If scenes change from dark to bright
suddenly, the screen may shake
vertically temporarily, but this is not a
fault.
No sound.
Checkpoint 1
Are you watching a programme in
slow or skip mode?
If you are playing a programme at a
speed other than normal speed,
sound will not be heard.
Checkpoint 2
Check the connections and settings.
(See pages 21~22, 37)
Checkpoint 3
Check whether the disc is damaged.
Clean the disc, if necessary.
Check whether the disc is inserted
correctly with the label facing up.
Reference
No audio output.
Checkpoint 1
Timer lamp flickers.
Checkpoint 1
Check there is enough space in the
disc or HDD for recording.
Checkpoint 2
Check whether the current disc is
recordable or not.
Make sure to check before the start
time of recording.
Some low quality discs may not play
properly.
Sound
Checkpoint 4
Page 128
Check whether you have selected
the correct digital output options in
the Audio Output Options menu.
(See page 37)
128 - English
Timer recording does not work properly.
Checkpoint 1
Re-check the recording time and the
end time settings again.
Checkpoint 2
Recording will be cancelled if the
power is interrupted due to a power
failure or another similar reason
while recording.
10-00819S-XSA_126-131_Reference
6/9/05
1:57 PM
Remote Control Unit
Page 129
Other problems.
The remote control doesn't work.
Checkpoint 1
Checkpoint 2
Checkpoint 3
Point the remote control at the remote
control sensor on your HDD & DVD
RECORDER. Allow for proper
distance. Remove obstacles between
your HDD & DVD RECORDER and
the remote control.
Checkpoint 1
Read the table of contents and then
find and read the section describing
your problem, follow the instructions
given.
Checkpoint 2
Plug your HDD &DVD RECORDER
off and on.
Checkpoint 3
If the problem still persists, contact a
nearby Samsung service centre.
Check whether the batteries are
empty.
Check whether TV control button is
selected or not.
Other
I forgot my password for parental supervision.
Checkpoint 1
Press and hold the
button on the
front panel of the Recorder for more
than 5 seconds with no disc in the
unit. All settings including the
password will revert to the factory
settings. Do not use this unless
absolutely necessary. (Note that this
function is possible only when no disc
is inserted.)
Checkpoint 1
Reference
Is it possible to change a subtitle and an audio
signal on a recorded disc?
A recorded disc is played with only
the subtitle and the audio signal
which were selected during recording.
English - 129
10-00819S-XSA_126-131_Reference
6/9/05
1:57 PM
Page 130
Specifications
Power requirements
220-240V AC, 50Hz
Power consumption
45 Watts
Weight
General
Dimensions
4.2 Kg
430mm(W) x 255mm(D) x 79mm(H)
Operating temp.
+5°C to +35°C
Other conditions
Keep level when operating. Less than 75% operating humidity
Composite Video : 1.0 V p-p at 75Ω load, sync negative
Video
Input
Audio
Max.Audio Input Level : 2Vrms
DV Input
IEEE 1394(4p) compatible jack
Receivable Channels
Audio
Output
S-Video input (Y: 1.0Vp-p, C: 0.286Vp-p at 75Ω load)
PAL-B/G, B/B
Analogue output jacks x 2
Optical/Coaxial digital audio output
Composite Video : Video output jack x 1
Video
S-Video output x 1 (Y:1.0Vp-p, C:0.286Vp-p at 75Ω load)
Component output x 1 (Y: 1.0Vp-p, Pb: 0.70Vp-p, Pr: 0.70Vp-p at 75Ω load)
Picture Compression format
MPEG-II
Audio Compression format
Dolby Digital 2ch/256Kbps, MPEG-II
Recording
Recording Quality
XP (about 8.5 Mbps), SP (about 4.5 Mbps), LP (about 2.5 Mbps),
EP (about 1.6 Mbps or about 1.2 Mbps)
Audio Frequency Response
20 Hz~20 kHz
Reference
Audio Output
For DVD discs, audio signals recorded at 96kHz sampling frequency are converted into and output at 48kHz.
Disc Type
DVD
AUDIO CD(CD-DA)
Analog Audio Output
48 / 96kHz
44.1kHz
Digital Audio Output
48kHz
44.1kHz
130 - English
10-00819S-XSA_126-131_Reference
6/9/05
1:57 PM
Page 131
ELECTRONICS
AK68-00819S-01

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Download PDF

advertisement