Samsung | HW-MS550 | Samsung 450W 2.0Ch Soundbar HW-MS550 User Manual

FULL MANUAL
HW-MS550 / HW-MS551
Imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service, please register
your product at www.samsung.com/register
SAFETY INFORMATION
SAFETY WARNINGS
WARNING
•• To reduce the risk of fire or electric shock, do
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
not expose this appliance to rain or moisture.
NOT REMOVE THE COVER (OR BACK).
CAUTION
NO USER-SERVICEABLE PARTS ARE INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
•• TO PREVENT ELECTRIC SHOCK, MATCH WIDE
PERSONNEL.
BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
•• This apparatus shall always be connected to a
CAUTION
AC outlet with a protective grounding
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
connection.
This symbol indicates that high voltage
is present inside. It is dangerous to make
any kind of contact with any internal
part of this product.
This symbol indicates that important
literature concerning operation and
maintenance has been included with
this product.
•• To disconnect the apparatus from the mains,
the plug must be pulled out from the mains
socket, therefore the mains plug shall be
readily operable.
•• Do not expose this apparatus to dripping or
splashing. Do not put objects filled with
liquids, such as vases on the apparatus.
•• To turn this apparatus off completely, you
must pull the power plug out of the wall
Class II product : This symbol indicates
socket. Consequently, the power plug must
that it does not require a safety
be easily and readily accessible at all times.
connection to electrical earth (ground).
AC voltage : This symbol indicates that
the rated voltage marked with the
symbol is AC voltage.
DC voltage : This symbol indicates that
the rated voltage marked with the
symbol is DC voltage.
Caution, Consult instructions for use :
This symbol instructs the user to consult
the user manual for further safety
related information.
ENG - ii
PRECAUTIONS
5. The battery used with this product contains
chemicals that are harmful to the
environment. Do not dispose of the battery
1. Ensure that the AC power supply in your
in the general household trash. Do not
house complies with the power
expose the battery to excess heat, direct
requirements listed on the identification
sunlight, or fire. Do not short circuit,
sticker located on the back of your product.
disassemble, or overheat the battery.
Install your product horizontally, on a
Danger of explosion if the battery is replaced
suitable base (furniture), with enough space
incorrectly. Replace only with the same or
around it for ventilation (7~10 cm). Make sure
equivalent type.
the ventilation slots are not covered. Do not
place the unit on amplifiers or other
equipment which may become hot. This unit
is designed for continuous use. To fully turn
off the unit, disconnect the AC plug from the
wall outlet. Unplug the unit if you intend to
ABOUT THIS MANUAL
The user manual has two parts: this simple paper
USER MANUAL and a detailed FULL MANUAL you
can download.
leave it unused for a long period of time.
2. During thunderstorms, disconnect the AC
plug from the wall outlet. Voltage peaks due
to lightning could damage the unit.
3. Do not expose the unit to direct sunlight or
other heat sources. This could lead to
USER MANUAL
overheating and cause the unit to
See this manual for safety instructions,
malfunction.
product installation, components,
4. Protect the product from moisture (i.e.
connections, and product specifications.
vases), and excess heat (e.g. a fireplace) or
equipment creating strong magnetic or
electric fields. Unplug the power cable from
the AC wall socket if the unit malfunctions.
Your product is not intended for industrial
use. It is for personal use only. Condensation
may occur if your product has been stored in
cold temperatures. If transporting the unit
during the winter, wait approximately
2 hours until the unit has reached room
temperature before using.
FULL MANUAL
You can access the Full Manual on Samsung’s
on-line customer support centre by scanning
the QR code. To see the manual on your PC or
mobile device, download the manual in
document format from the website.
(http://www.samsung.com/support)
Design, specifications and App screen are subject to
change without prior notice.
ENG - iii
CONTENTS
01
Checking the Components
2
Inserting Batteries before using the Remote Control (AA batteries X 2) -------------------------- 2
02
03
Product Overview
3
Front Panel / Right Side Panel of the Soundbar
-------------------------- 3
Bottom Panel of the Soundbar
-------------------------- 4
Connecting the Soundbar
Connecting Electrical Power
04
05
06
5
-------------------------- 5
Connecting to your TV
7
Method 1. Connecting with a Cable
–– Connecting a TV using an HDMI Cable
–– Connecting using an Optical Cable
-------------------------- 7
-------------------------- 7
-------------------------- 8
Method 2. Connecting Wirelessly
–– Connecting a TV via Bluetooth
–– Connecting via Wi-Fi
-------------------------- 9
-------------------------- 9
-------------------------- 11
Connecting an External Device
13
Connecting using an HDMI Cable
-------------------------- 13
Connecting using an Optical or Analogue Audio (AUX) Cable
-------------------------- 14
Connecting a USB
15
ENG - iv
07
08
Connecting a Mobile Device
17
Method 1. Connecting via Bluetooth
-------------------------- 17
Method 2. Connecting via Wi-Fi (Wireless Network)
-------------------------- 20
Using the Remote Control
22
How to Use the Remote Control
-------------------------- 22
Adjusting the Soundbar volume with a TV remote control
-------------------------- 25
Using the Hidden Buttons
-------------------------- 26
09
Software Update
26
10
Installing the Wall Mount
27
Installation Precautions
-------------------------- 27
Wallmount Components
-------------------------- 27
Assembling the Holder-Cable
-------------------------- 29
11Troubleshooting
30
12Licence
31
13
Open Source Licence Notice
31
14
Important Notes About Service
32
15
Specifications and Guide
32
Specifications
-------------------------- 32
ENG - v
01 CHECKING THE COMPONENTS
SMART
MODE
Surround
SOUND
MODE
VOL
BASS
SOUNDBAR
Soundbar Main Unit
Power Cord
Remote Control /
Batteries
Holder-Cable
HDMI Cable
Screw
•• For Soundbar wall mounting components, see page 27.
•• See page 29 for instructions on how to use the Holder-Cable.
•• To purchase additional components or optional cables, contact a Samsung Service Centre or
Samsung Customer Care.
•• The appearance of the accessories may differ slightly from the illustrations above.
Inserting Batteries before using the Remote Control (AA batteries X 2)
Slide the battery cover in the direction of the arrow until it is completely removed. Insert 2 AA batteries
(1.5V) oriented so that their polarity is correct. Slide the battery cover back into position.
ENG - 2
02 PRODUCT OVERVIEW
Front Panel / Right Side Panel of the Soundbar
Position the product so that the
SAMSUNG logo is located on the top.
Right Side of the Soundbar
Display
Displays the product’s status and current mode.
-/+ (Volume) Button
Adjusts the volume.
•• When adjusted, the volume level appears on the Soundbar’s front display.
(Source) Button
Selects the source input mode.
Input mode
Display
Optical Digital input
D.IN
ARC (HDMI OUT) input
D.IN  TV ARC (Auto conversion)
AUX input
AUX
HDMI input
HDMI
Wi-Fi mode
WIFI
BLUETOOTH mode
BT
USB mode
USB
•• To turn on “BT PAIRING” mode, change the source to “BT” mode, and then press and hold the
(Source) button for more than 5 seconds.
(Power) Button
Turns the power on and off.
ENG - 3
•• When you plug in the AC cord, the power button will begin working in 4 to 6 seconds.
•• When you turn on this unit, there will be a 4 to 5 second delay before it produces sound.
•• If you want to enjoy sound only from the Soundbar, you must turn off the TV’s speakers in the Audio
Setup menu of your TV. Refer to the owner’s manual supplied with your TV.
Bottom Panel of the Soundbar
POWER
OUT
(For TV)
POWER
IN
DIGITAL AUDIO IN
(OPTICAL)
WIRELESS
AUX IN
DIGITAL AUDIO IN
(OPTICAL)
HDMI IN
HDMI OUT
(TV-ARC)
USB (5V 0.5A)
POWER
OUT
(For TV)
USB (5V 0.5A)
Wi-Fi SETUP SPK ADD
HDMI IN
WIRELESS
POWER
IN
AUX IN
HDMI OUT
(TV-ARC)
Wi-Fi SETUP SPK ADD
POWER OUT (For TV)
Connect the power cord of a Samsung TV connected to the Soundbar and mounted on the wall using a
Wall Mount Kit (WMN300SB - not supplied).
POWER IN
Connect the Soundbar's AC power cable.
DIGITAL AUDIO IN (OPTICAL)
Connect to the digital (optical) output of an external device.
WIRELESS
Attach the wireless dongle that connects the Soundbar to surround speakers and a subwoofer wirelessly.
(The surround speaker, subwoofer, and wireless dongle are sold separately.)
•• The WIRELESS jack is not USB-compatible.
•• The availability of subwoofers differs by area. Check the availability at
http://www.samsung.com/support.
ENG - 4
AUX IN
Connect to the Analogue output of an external device.
USB (5V 0.5A)
Connect a USB device here to play music files on the USB device through the Soundbar.
HDMI IN
Inputs digital video and audio signals simultaneously using an HDMI cable.
Connect to the HDMI output of an external device.
HDMI OUT (TV-ARC)
Connect to the HDMI (ARC) jack on a TV.
Wi-Fi SETUP / SPK ADD
Connect to a wireless network (Wi-Fi) via the Samsung Multiroom app.
•• When disconnecting the power cable from a wall outlet, pull the plug. Do not pull the cable.
•• Do not connect this unit or other components to an AC outlet until all connections between
components are complete.
03 CONNECTING THE SOUNDBAR
Connecting Electrical Power
•• For more information about the required electrical power and power consumption, refer to the
label attached to the product. (Label : Bottom of the Soundbar Main Unit)
•• Connect the supplied power cable to the
POWER IN jack.
Power Cord
POWER
IN
USB (5V 0.5A)
Connecting
Electrical Power
POWER
OUT
(For TV)
DIGITAL AUDIO IN
(OPTICAL)
HDMI IN
WIRELESS
POWER
IN
AUX IN
HDMI OUT
(TV-ARC)
Bottom of the Soundbar
Main Unit
ENG - 5
•• The POWER OUT jack is used to provide
power to a Samsung TV mounted on the wall
POWER
OUT
(For TV)
using a Wall Mount Kit (WMN300SB - not
supplied).
•• The POWER OUT jack can connect only to
Samsung TVs that use a 2-pin power cord and
consume 400 W or less. (Connecting the jack
POWER IN
to a device that consumes more than 400 W
may damage the Soundbar or cause a
USB (5V 0.5A)
POWER
OUT
(For TV)
DIGITAL AUDIO IN
(OPTICAL)
HDMI IN
WIRELESS
POWER
IN
AUX IN
malfunction.)
HDMI OUT
(TV-ARC)
Bottom of the Soundbar Main Unit
For a list of Samsung TVs that are compatible
with the WMN300SB Wall Mount Kit and the
POWER OUT jack, see the WMN300SB
Wall Mount Kit user manual.
You can view the manual on line at
http://www.samsung.com/support.
ENG - 6
04 CONNECTING TO YOUR TV
Hear TV sound from your Soundbar through wired or wireless connections.
•• When the Soundbar is connected to a selected Samsung TVs, the Soundbar can be controlled using
the TV’s remote control.
–– When using optical cable, this feature can be supported by 2017 Samsung Smart TVs that
support Bluetooth.
–– This function also allows you to use the TV menu to adjust the sound field and various settings
as well as the volume and mute.
Method 1. Connecting with a Cable
Connecting a TV using an HDMI Cable
Bottom of the Soundbar
Connect to the HDMI IN
(ARC) port of your TV.
HDMI IN
HDMI IN
(ARC)
HDMI Cable
HDMI OUT
(TV-ARC)
Connect to the HDMI OUT (TV-ARC)
port of the Soundbar main unit.
TV
ARC
Right Side of the
Soundbar
1. With the Soundbar and TV turned on, connect the HDMI cable as shown in the figure.
2. “TV ARC” appears in the display window of the Soundbar main unit and the Soundbar plays TV
sound.
•• If TV sound is inaudible, press the
(Source) button on the remote control or on the right side
of the Soundbar to switch to “D.IN” mode. The screen displays “D.IN” and “TV ARC” in sequence,
and TV sound is played.
ENG - 7
•• If “TV ARC” does not appear in the display window of the Soundbar main unit, confirm that the
cable is connected to the correct port.
•• Use the volume buttons on the TV’s remote control to change the volume of the Soundbar.
NOTES
•• HDMI is an interface that enables the digital transmission of video and audio data with just a single
connector.
•• If the TV provides an ARC port, connect the HDMI cable to the HDMI IN (ARC) port.
•• We recommend you use a coreless HDMI cable if possible. If you use a cored HDMI cable, use one
whose diameter is less than 14 mm.
•• Anynet+ must be turned on.
•• This function is not available if the HDMI cable does not support ARC.
Connecting using an Optical Cable
Bottom of the Soundbar
DIGITAL AUDIO IN
(OPTICAL)
OPTICAL OUT
Optical Cable
(not supplied)
WIRELESS
AUX IN
D.IN
Right Side of the Soundbar
1. Connect the DIGITAL AUDIO IN (OPTICAL) jack on the Soundbar to the OPTICAL OUT jack of the TV
with a digital optical cable (not supplied).
2. Press the
(Source) button on the right side panel or remote control, and then select the “D.IN”
mode.
Auto Power Link
Auto Power Link automatically turns on the Soundbar when the TV is turned on.
1. Connect the Soundbar and a TV with a digital optical cable (not supplied).
2. Press the
(Source) button on the right side panel or on the remote control, and then select
“D.IN”.
ENG - 8
3. Press the Left button on the remote control for 5 seconds to turn Auto Power
Link on or off.
•• Auto Power Link is set to ON by default.
(To turn off this function, turn off Auto Power using the Soundbar.)
•• Depending on the connected device, Auto Power Link may not function.
•• This function is only available in the “D.IN” mode.
Method 2. Connecting Wirelessly
Connecting a TV via Bluetooth
When a TV is connected using Bluetooth, you can hear stereo sound without the hassle of cabling.
•• Only one TV can be connected at a time.
The initial connection
1. Press the
(Source) button on the right side panel or on the remote control, and then select
“BT”.
2. Change “BT” to “BT PAIRING”.
•• If “BT READY” appears, press and hold the
(Source) button on the right side panel of the
Soundbar or on the remote control for more than 5 seconds to display “BT PAIRING”.
3. Select Bluetooth mode on the TV. (For more information, see the TV’s manual.)
4. Select “[AV] Samsung Soundbar MSxxx” from the list on TV’s screen.
An available Soundbar is indicated with “Need Pairing” or “Paired” on the TV Bluetooth device list.
To connect to the Soundbar, select the message and establish a connection.
•• When the TV is connected, [TV Name] → “BT” appears on the Soundbar’s front display.
5. You can now hear TV sound from the Soundbar.
ENG - 9
If the device fails to connect
•• If the previously connected Soundbar listing (e.g. “[AV] Samsung Soundbar MSxxx”) appears in the
list, delete it.
•• In “BT” mode, press and hold the
(Source) button for more than 5 seconds on the right side
panel of the Soundbar or on the remote control to switch to “BT PAIRING” mode.
Then, select “[AV] Samsung Soundbar MSxxx” from the TV’s search list.
What are the BT READY and BT PAIRING statuses?
•• BT READY : In this mode, you can search for previously connected TVs or connect to the Soundbar
from a previously connected mobile device.
•• BT PAIRING : In this mode, you can connect to a new device. (While in “BT” mode, press and hold the
(Source) button for more than 5 seconds on the right side of the Soundbar or on the remote
control.)
NOTES
•• If asked for a PIN code when connecting a Bluetooth device, enter <0000>.
•• In Bluetooth connection mode, the Bluetooth connection will be lost if the distance between the
Soundbar and the Bluetooth device exceeds 10 meters.
•• The Soundbar automatically turns off after 5 minutes in the Ready state.
•• The Soundbar may not perform Bluetooth search or connection correctly under the following
circumstances:
–– If there is a strong electrical field around the Soundbar.
–– If several Bluetooth devices are simultaneously paired with the Soundbar.
–– If the Bluetooth device is turned off, not in place, or malfunctions.
•• Electronic devices may cause radio interference. Devices that generate electromagnetic waves
must be kept away from the Soundbar main unit - e.g., microwaves, wireless LAN devices, etc.
Disconnecting the Soundbar from the TV
Press the
(Source) button on the right side panel or on the remote control and switch to any mode
but “BT”.
•• Disconnecting takes time because the TV must receive a response from the Soundbar.
(The time required may differ, depending on the TV model.)
•• To cancel automatic Bluetooth connection between the Soundbar and TV, press the
p (Play/Pause) button on the remote control for 5 seconds in “BT READY” status. (Toggle On → Off)
ENG - 10
Connecting via Wi-Fi
Pre-connection Checklist
1. Confirm that your Samsung smart TV was released after 2014. This function is compatible only
with Samsung smart TVs released after 2014.
2. Make sure your Wireless router (Wi-Fi) is ready and working.
3. Make sure that the TV is connected to the Wireless router (your Wi-Fi network).
Step 1 : Connecting the Soundbar to Wi-Fi
1. Press the
(Source) button on the right side of the Soundbar or on the remote control to select
“WIFI” mode.
•• When using selected Samsung TV (2016 or 2017 Samsung smart TVs that support Bluetooth.)
–– If you select “WIFI” mode when the TV is turned on, the TV screen displays a pop-up
window providing instructions on how to automatically connect the Soundbar to a wireless
router (Wi-Fi). Refer to instructions in the pop-up window of TV.
WIFI
2. Connect your mobile device (smartphone, tablet etc.) to the Wi-Fi network the TV is connected to.
3. Install and launch the Samsung Multiroom app on your mobile device (smartphone, tablet etc.).
Samsung Multiroom app
Android
iOS
4. Follow the instructions in the app screen on the mobile device to connect the Soundbar to your
Wi-Fi network.
ENG - 11
Step 2 : Configuring Settings on the TV
•• If the TV disconnects from your wireless network after you change the input source to the
Soundbar, use the TV menu to connect the TV to the network again.
For TVs released in 2017
1. Home menu  Settings (
)  Sound  Sound Output  Select [AV] Soundbar MSxxx (Wi-Fi)
2. The Soundbar outputs TV sound.
For TVs released in 2016
1. Home menu  Settings (
)  Sound  Sound Output  Select [AV] Samsung Soundbar MSxxx
(Wi-Fi)
2. The Soundbar outputs TV sound.
For TVs released in 2015
1. Home menu  Sound  Speaker List  Select [AV] Samsung Soundbar MSxxx (Wi-Fi)
2. The Soundbar outputs TV sound.
For TVs released in 2014
1. Home menu  Sound  Speaker Settings  Select Multiroom Link - Settings 
Soundbar+Surround.
2. From the Soundbar menu item, select “[AV] Samsung Soundbar MSxxx” and then select “OK”.
3. Home menu  Sound  Speaker Settings  Select TV Sound Output  Multiroom Link
Speaker Settings
Multiroom Link
TV Sound Output
Multiroom Link
TV Speaker
• TV Installation Type
TV SoundConnect
• Samsung Audio Device List
• Add New Device
Multiroom Link
• Settings
Soundbar+Surround
3
Stand
Soundbar
On
Soundbar+Surround
Bluetooth Headphone
• Bluetooth Headphone List
OK
[AV] Samsung Soundbar MSxxx [AV] Samsung Soundbar MSxxx
c
1
2
Don’t Use
OK
Volume Level
Speaker Test
Edit Na
4. The Soundbar outputs TV sound.
NOTES
•• The TV and Soundbar must be connected to the same wireless network (Wi-Fi).
•• If your wireless router (Wi-Fi) uses a DFS channel, you will not be able to establish a Wi-Fi
connection between the TV and Soundbar. Contact your Internet service provider for details.
•• If the 5GHz Wi-Fi connection is not smooth, use the 2.4GHz bandwidth.
ENG - 12
05 CONNECTING AN EXTERNAL DEVICE
Connect to an external device via a wired or wireless network to play the external device’s sound
through the Soundbar.
Connecting using an HDMI Cable
Bottom of the Soundbar
External Device
HDMI IN
HDMI OUT
HDMI Cable
HDMI OUT
(TV-ARC)
HDMI IN
(ARC)
HDMI Cable
HDMI
Right Side of the
Soundbar
1. Connect an HDMI cable from the HDMI IN jack on the back of the product to the HDMI OUT jack on
your digital device.
2. Connect an HDMI cable from the HDMI OUT (TV-ARC) jack on the back of the product to the HDMI
IN jack on your TV.
3. Press the
(Source) button on the right side panel or on the remote control, and then select
“HDMI”.
4. “HDMI” mode is displayed on the Soundbar display panel and sound plays.
ENG - 13
Connecting using an Optical or Analogue Audio (AUX) Cable
Right Side of the Soundbar
BD / DVD player / Set-top box /
Game console
OPTICAL OUT
DIGITAL AUDIO IN
(OPTICAL)
Optical Cable
(not supplied)
WIRELESS
OR
R - AUDIO - L
AUX IN
Audio (AUX) Cable
Bottom of the Soundbar
(not supplied)
Optical Cable
XX Connect DIGITAL AUDIO IN (OPTICAL) on the main unit to the OPTICAL OUT jack of the Source
Device using a digital optical cable (not supplied).
YY Select “D.IN” mode by pressing the
(Source) button on the right side panel or on the remote
control.
OR
Audio (AUX) Cable
XX Connect AUX IN (Audio) on the main unit to the AUDIO OUT jack of the Source Device using an audio
cable.
YY Select “AUX” mode by pressing
(Source) button on the right side panel or on the remote control.
ENG - 14
06 CONNECTING A USB
You can play music files located on USB storage devices through the Soundbar.
Display
USB port
USB (5V 0.5A)
POWER
OUT
(For TV)
DIGITAL AUDIO IN
(OPTICAL)
Wi-Fi SETUP SPK ADD
HDMI IN
WIRELESS
POWER
IN
AUX IN
HDMI OUT
(TV-ARC)
USB
USB (5V 0.5A)
1. Connect the USB device to the USB port on the back of the product.
2. Press the
(Source) button on the right side panel or on the remote control, and then select
“USB”.
3. “USB” appears in the display screen.
4. Play music files from the USB storage device through the Soundbar.
•• The Soundbar automatically turns off (Auto Power Off) if no USB device has been connected for
more than 5 minutes.
ENG - 15
File Format Type Compatibility list
Extension
Codec
Sampling Rate
Bit Rate
*.mp3
MPEG 1 Layer2
16KHz ~ 48KHz
80kbps~320kbps
MPEG 1 Layer3
16KHz ~ 48KHz
80kbps~320kbps
MPEG 2 Layer3
16KHz ~ 48KHz
80kbps~320kbps
MPEG 2.5 Layer3
16KHz ~ 48KHz
80kbps~320kbps
Wave_Format_MSAudio1
16KHz ~ 48KHz
56kbps~128kbps
Wave_Format_MSAudio2
16KHz ~ 48KHz
56kbps~128kbps
AAC
16KHz ~ 96KHz
48kbps~320kbps
AAC-LC
16KHz ~ 96KHz
128kbps~192kbps
5.1ch 320kbps
HE-AAC
24KHz ~ 96KHz
48kbps~64kbps
5.1ch 160kbps
*.wav
-
16KHz ~ 48KHz
up to 3000kbps
*.ogg
OGG 1.1.0
16KHz ~ 48KHz
50kbps~500kbps
*.flac
FLAC 1.1.0, FLAC 1.2.1
16KHz ~ 96KHz
up to 3000kbps
*.wma
*.aac
•• If there are too many folders and files stored on the USB device, it may take the Soundbar some
time to access and play files.
ENG - 16
07 CONNECTING A MOBILE DEVICE
Method 1. Connecting via Bluetooth
When a mobile device is connected using Bluetooth, you can hear stereo sound without the hassle of
cabling.
•• You cannot connect more than one Bluetooth device at a time.
Bluetooth device
The initial connection
1. Press the
(Source) button on the right side panel or on the remote control, and then select
“BT”.
2. Change “BT” to “BT PAIRING”.
•• If “BT READY” appears, press and hold the
(Source) button on the right side panel of the
Soundbar or on the remote control for more than 5 seconds to display “BT PAIRING”.
3. Select “[AV] Samsung Soundbar MSxxx” from the list.
•• When a Soundbar is connected to the Bluetooth device, [Bluetooth Device Name] → “BT”
appears in the front display.
4. Play music files from the device, connected via Bluetooth, through the Soundbar.
If the device fails to connect
•• If the previously connected Soundbar listing (e.g. “[AV] Samsung Soundbar MSxxx”) appears in the
list, delete it.
•• In “BT” mode, press and hold the
(Source) button for more than 5 seconds on the right side
panel of the Soundbar or on the remote control to switch to “BT PAIRING” mode.
Then, select “[AV] Samsung Soundbar MSxxx” from the Bluetooth device search list.
ENG - 17
What are the BT READY and BT PAIRING statuses?
•• BT READY : In this mode, you can search for previously connected TVs or connect to the Soundbar
from a previously connected mobile device.
•• BT PAIRING : In this mode, you can connect to a new device. (While in “BT” mode, press and hold the
(Source) button for more than 5 seconds on the right side of the Soundbar or on the remote
control.)
NOTES
•• If asked for a PIN code when connecting a Bluetooth device, enter <0000>.
•• In Bluetooth connection mode, the Bluetooth connection will be lost if the distance between the
Soundbar and the Bluetooth device exceeds 10 meters.
•• The Soundbar automatically turns off after 5 minutes in the Ready state.
•• The Soundbar may not perform Bluetooth search or connection correctly under the following
circumstances:
–– If there is a strong electrical field around the Soundbar.
–– If several Bluetooth devices are simultaneously paired with the Soundbar.
–– If the Bluetooth device is turned off, not in place, or malfunctions.
•• Electronic devices may cause radio interference. Devices that generate electromagnetic waves
must be kept away from the Soundbar main unit - e.g., microwaves, wireless LAN devices, etc.
•• The Soundbar supports SBC data (44.1kHz, 48kHz).
•• Connect only to a Bluetooth device that supports the A2DP (AV) function.
•• You cannot connect the Soundbar to a Bluetooth device that supports only the HF (Hands Free)
function.
•• Once you have paired the Soundbar to a Bluetooth device, selecting “[AV] Samsung Soundbar
MSxxx” from the device’s scanned devices list will automatically change the Soundbar to “BT”
mode.
–– Available only if the Soundbar is listed among the Bluetooth device’s paired devices.
(The Bluetooth device and the Soundbar must have been previously paired at least once.)
•• The Soundbar will appear in the Bluetooth device’s searched devices list only when the Soundbar is
displaying “BT READY”.
•• Soundbar cannot be paired to another Bluetooth device, while using the Bluetooth function.
ENG - 18
Disconnecting the Bluetooth device from a Soundbar
You can disconnect a Bluetooth device from the Soundbar. For instructions, see the Bluetooth device’s
user manual.
•• The Soundbar will be disconnected.
•• When the Soundbar is disconnected from the Bluetooth device, the Soundbar will display
“BT DISCONNECTED” on the front display.
Disconnecting the Soundbar from the Bluetooth device
Press the
(Source) button on the right side panel or on the remote control, and then change to any
mode except “BT”.
•• Disconnecting takes time because the Bluetooth device must receive a response from the
Soundbar. (Disconnection time may differ, depending on the Bluetooth device)
•• When the Soundbar is disconnected from the Bluetooth device, the Soundbar will display
“BT DISCONNECTED” on the front display.
NOTES
•• In Bluetooth connection mode, the Bluetooth connection will be lost if the distance between the
Soundbar and the Bluetooth device exceeds 10 meters.
•• The Soundbar automatically turns off after 5 minutes in the Ready state.
More About Bluetooth
Bluetooth is a technology that enables Bluetooth-compliant devices to interconnect easily with each
other using a short wireless connection.
•• A Bluetooth device may cause noise or malfunction, depending on usage, if:
–– A part of your body is in contact with the receiving/transmitting system of the Bluetooth
device or the Soundbar.
–– It is subject to electrical variation from obstructions caused by a wall, corner, or office partition.
–– It is exposed to electrical interference from same frequency-band devices including medical
equipment, microwave ovens, and wireless LANs.
•• Pair the Soundbar with the Bluetooth device while they are close together.
•• The further the distance between the Soundbar and Bluetooth device, the worse the quality is.
If the distance exceeds the Bluetooth operational range, the connection is lost.
•• In poor reception areas, the Bluetooth connection may not work properly.
•• The Bluetooth connection only works when it is close to the unit. The connection will be
automatically cut off if the Bluetooth device is out of range. Even within range, the sound quality
may be degraded by obstacles such as walls or doors.
•• This wireless device may cause electric interference during its operation.
ENG - 19
Method 2. Connecting via Wi-Fi (Wireless Network)
•• Connect a single Soundbar to Wi-Fi to access a variety of music streaming services and Internet
radio. Connect multiple Soundbars to Wi-Fi to use grouped playback or stereo sound mode.
•• To connect a Soundbar to a mobile device via a wireless network (Wi-Fi), the Samsung Multiroom
app is required.
Mobile device
The initial connection
1. Press the
(Source) button on the right side of the Soundbar or on the remote control to select
“WIFI” mode.
WIFI
2. Install and launch the Samsung Multiroom app on your mobile device (e.g. smartphone or tablet).
Samsung Multiroom app
Android
iOS
3. Follow the instructions in the app screen on the mobile device to connect the Soundbar to Wi-Fi.
ENG - 20
Installing an additional Soundbar when Samsung wireless speakers are already in use
1. On the Home screen of the Samsung Multiroom app, select Settings (
) at the top, and then
select “Add Speaker”.
2. To connect the Soundbar to 2 Samsung wireless speakers and configure a surround sound system,
follow the steps shown below. (You cannot set up a surround sound system using one audio device
and one Soundbar.)
XX Touch to go to the list of all speakers.
YY Touch on the right of the Soundbar model name.
ZZ Touch Surround Setup. Select Done after dragging the speaker to the desired location.
[[ The Surround connection is complete.
Soundbar
NOTE
•• To connect an additional SWA-9000S (not supplied), disconnect the Samsung wireless speakers
from the Soundbar to disable the surround sound system. (If connecting the surround speakers
without disconnecting SWA-9000S, sound is played via both the Samsung wireless speaker and the
Surround speaker.)
ENG - 21
08 USING THE REMOTE CONTROL
How to Use the Remote Control
Turns the Soundbar on and off.
Power
You can select from TREBLE, SYNC,
REAR LEVEL, or REAR SPEAKER ON/OFF.
Sound Control
•• To adjust the TREBLE volume, select Sound
Control TREBLE, and then use the
••
SMART
MODE
Surround
SOUND
MODE
VOL
BASS
Surround
Surround
••
SOUNDBAR
SOUND
MODE
SOUND
MODE
••
VOL
VOL
ENG - 22
••
Up/Down buttons to adjust the volume
within the -6 to +6 range.
Press and hold the
(Sound Control)
button for about 5 seconds to adjust the
sound for each frequency band. 150Hz,
300Hz, 600Hz, 1.2KHz, 2.5KHz, 5KHz, and
10KHz are selectable (Left/Right) and each
can be adjusted to a setting between
-6 to +6 (Up/Down).
If the
video and audio between the TV and
SMART
MODE
SMART
your
Soundbar are not synchronised, select
MODE
SYNC in Sound Control, and then set audio
delay between 0~300 milliseconds by
using the Up/Down buttons. (Except “USB”
mode)
If surround speakers (not supplied) are
connected, select REAR LEVEL and use the
Up/Down buttons to adjust the volume
within the -6 to +6 range.
The REAR SPEAKER function can be turned
ON/OFF
by using the Up/Down buttons.
BASS
Audio Sync is only supported in some
BASS
functions.
The Surround Sound function adds depth and a sense of space to sound.
SMART
Each time
MODEyou press this button, ON and OFF alternate.
SMART
•
•
ON
: Play sound over all the speakers.
MODE
•• OFF : You can hear the sound of the original source channel from several speakers.
Surround
Surround
Surround
SOUND
MODE
SOUND
MODE
SOUND MODE
VOL
•• DRC (Dynamic Range Control)
Lets you apply dynamic range control to Dolby Digital tracks. If you press and hold the
SOUND MODE button while in standby mode, DRC (Dynamic Range Control) turns on
or off. With the DRC turned on, loud sound is reduced. (The sound may be distorted.)
BASS
VOL
BASS
Source
SMART
MODE
Surround
You can select the desired sound effect by choosing STANDARD, MUSIC, CLEAR VOICE,
SPORTS, or MOVIE.
Select the “STANDARD” mode if you want to enjoy the original sound.
Press to select a source connected to the Soundbar.
•• BT PAIRING mode
To turn on “BT PAIRING” mode in “BT” mode, press and hold the
(Source) button
for more than 5 seconds. See page 17 for details.
•• Auto Power Down Function
The unit turns off automatically in the following situations.
–– D.IN / WIFI / BT / USB Mode : If there is no audio signal for 5 minutes.
–– HDMI Mode : If there is no audio signal for 15 minutes.
–– AUX Mode :
–– If the Audio (AUX) Cable is disconnected for 5 minutes.
–– If there is no KEY input for 8 hours when the Audio (AUX) Cable is connected.
(Auto Power Down function can be turned off only in that case.)
–– To turn off Auto Power Down function, while in “AUX” mode, press and hold the
p button for 5 seconds. “ON-AUTO POWER DOWN” / “OFF-AUTO POWER
DOWN” appears on the display.
Press the p button to pause a music file temporarily.
If you press the button again, the music file plays.
SOUND
MODE
Play / Pause
(BT/Wi-Fi)
SMART
MODE
Surround
VOL
BASS
SOUND
MODE
VOL
BASS
ENG - 23
Press the indicated areas to select Up/Down/Left/Right.
Up/Down/
SMART
MODE
Surround
Left/Right
Press Up/Down/Left/Right on the button to select or set functions.
SOUND
MODE
•• Repeat
To use the Repeat function press the Up button.
VOL
•• Music Skip
Press the Right button to select the next music file. Press the Left button to select
the previous music file.
BASS
•• Anynet+ / Auto Power Link
You can turn Anynet+ and Auto Power Link on or off.
Anynet+ and Auto Power Link are controlled by the Right and Left buttons
respectively.
SMART
MODE
Surround
Surround
–– Anynet+ : If the Soundbar is connected to a Samsung TV through an HDMI cable,
you can control your Soundbar with the Samsung TV’s remote control.
Press and hold the Right button for 5 seconds to toggle Anynet+ ON and OFF.
–– Auto Power Link : If the Soundbar is connected to your TV through a digital
optical cable, the Soundbar can automatically turn on when you turn on your TV.
Press and hold the Left button for 5 seconds to toggle Auto Power Link ON and
OFF.
–– Anynet+ / Auto Power Link are set to ON by default.
SOUND
MODE
Automatically optimises sound effects to suit the scene currently playing.
The mode turns on or off each time the button is pressed.
SMART
MODE
SMART MODE
SM
M AR
OD T
E
N
SO
U
VO
L
D
BA
R
BA
SS
SO
M UN
OD D
E
N
D
U
SO
VO
L
BA
R
Su
rro
un
d
BA
SS
Su
rro
un
d
BA
SS
D
BA
R
N
VO
L
BASS
SO
U
N
D
U
SO
VOL
SO
M UN
OD D
E
SM
M AR
OD T
E
BASS
BASS
BA
R
BA
SS
Su
rro
un
d
VOL
SO
M UN
OD D
E
SM
M AR
OD T
E
SOUND
MODE
Push the button up or down to adjust the BASS volume within the -6 to +6 range.
To set the BASS volume level to 0, press the button.
•• When a Subwoofer (not supplied) is connected, the BASS button switches to the
Subwoofer Key. Push the button up or down to adjust the subwoofer volume either to
-12 or within the -6 to +6 range. To set the subwoofer volume level to 0, press the
button.
ENG - 24
BA
SS
Push the button up or down to adjust the volume.
•• Mute
Press the VOL button to mute the sound. Press it again to unmute the sound.
Adjusting the Soundbar volume with a TV remote control
Use the TV menu to set the TV speaker on a Samsung TV to external speakers.
(For more information, see the TV’s user manual.)
•• After installing the Soundbar, you can adjust the Soundbar’s volume using the IR remote control
that came with a Samsung TV. (If you do not want to use this function, when the Soundbar is on,
press and hold the Surround button for 5 seconds. “OFF-TV REMOTE” appears in the Soundbar’s
display and the function turns off.) To adjust the volume using only the Samsung TV remote control,
press and hold the Surround button for more than 5 seconds until “SAMSUNG-TV REMOTE”
appears in the Soundbar display.
–– Each time the Surround button is held for 5 seconds, the mode switches in the following order:
“SAMSUNG-TV REMOTE” (Default mode) → “OFF-TV REMOTE” → “ALL-TV REMOTE”.
•• To adjust the Soundbar volume with the remote control that came with a TV made by a third party
manufacturer, turn the Soundbar on, press and hold the Surround button for 5 seconds
(“OFF-TV REMOTE” appears on the Soundbar’s display), release the Surround button, and then
press and hold the Surround button again for more than 5 seconds. (“ALL-TV REMOTE” appears on
the Soundbar’s display.)
–– This function may not be available, depending on the remote control.
–– Manufacturers supporting this function:
VIZIO, LG, Sony, Sharp, PHILIPS, PANASONIC, TOSHIBA, GRUNDIG, Hisense, RCA
ENG - 25
SO
M UN
OD D
E
VO
L
BA
R
VO
L
U
N
D
SO
BA
R
SO
U
N
D
VO
L
Su
rro
un
d
SM
M AR
OD T
E
SM
M AR
OD T
E
SO
M UN
OD D
E
BA
SS
Su
rro
un
d
SO
M UN
OD D
E
Su
rro
un
d
U
N
D
SO
VO
L
BA
R
BA
SS
SO
M UN
OD D
E
BASS
Su
rro
un
d
VOL
VOL
SM
M AR
OD T
E
SM
M AR
OD T
E
Using the Hidden Buttons
Hidden Button
Reference page
Remote Control Button
Function
Surround
TV remote control On/Off
page 25
BT Paring
page 17
p (Play / Pause)
Auto Power Down On/Off
(AUX mode)
page 23
Left
Auto Power Link ON/OFF
page 8
Right
Anynet+ ON/OFF
page 24
7 Band EQ
page 22
DRC ON/OFF (Standby)
page 23
(Source)
(Sound Control)
SOUND MODE
09 SOFTWARE UPDATE
When the Soundbar is connected to the Internet, software updates automatically occur even when the
Soundbar is turned off.
•• To use the Auto Update function, the Soundbar must be connected to the Internet.
The Wi-Fi connection to the Soundbar will be terminated if its power cord is disconnected or the
power is cut off. If the power is cut off, turn on the Soundbar and reconnect it.
ENG - 26
10 INSTALLING THE
WALL MOUNT
Wallmount Components
450mm
Installation Precautions
Wall Mount Guide
•• Install on a vertical wall only.
•• Do not install in a place with high
temperature or humidity.
•• Verify whether the wall is strong enough to
support the product’s weight. If not, reinforce
Holder-Screw (2 EA)
Screw (2 EA)
the wall or choose another installation point.
•• Purchase and use the fixing screws or
anchors appropriate for the kind of wall you
have (plaster board, iron board, wood, etc.).
Bracket-Wall Mount (2 EA)
If possible, fix the support screws into wall
studs.
•• Purchase wall mounting screws according to
the type and thickness of the wall you want to
1. Place the Wall Mount Guide against the wall
mount the Soundbar on.
surface.
•• The Wall Mount Guide must be level.
–– Diameter: M5
–– Length: 35 mm or longer recommended.
•• Connect cables from the unit to external
•• If your TV is mounted on the wall, install
the Soundbar at least 5 cm below the TV.
devices before you install the Soundbar on
the wall.
•• Make sure the unit is turned off and
unplugged before you install it. Otherwise, it
may cause an electric shock.
ENG - 27
5 cm or more
2. Align the Paper Template’s Centre Line with
5. Push a screw (not supplied) through each
the centre of your TV (if you are mounting
Holder-Screw, and then screw each screw
the Soundbar below your TV), and then fix
firmly into a support screw hole.
the Wall Mount Guide to the wall using tape.
•• If you are not mounting below a TV, place
the Centre Line in the centre of the
installation area.
6. Install the 2 Bracket-Wall Mounts in the
correct orientation on the bottom of the
450mm
Soundbar, using 2 Screws.
Centre Line
3. Use a sharp object, such as a pen or pencil, to
mark the holes’ positions, and then remove
the Wall mount Guide.
450mm
CENTER LINE
•• When assembling, make sure the hanger
part of the Bracket-Wall Mounts are
located behind the rear of the Soundbar.
4. Using an appropriately sized drill bit, drill a
hole in the wall at each marking.
Rear of Soundbar
•• If the markings do not correspond to the
positions of studs, make sure you insert
appropriate anchors or mollies into the
holes before you insert the support
screws. If you use anchors or mollies,
make sure the holes you drill are large
enough for the anchors or mollies you
use.
Right end of Soundbar
ENG - 28
Assembling the Holder-Cable
7. Install the Soundbar with the attached
Bracket-Wall Mounts by hanging the
Bracket-Wall Mounts on the Holder-Screws
on the wall.
As shown in the image, use the supplied Screw to
fix the Holder-Cable to the Soundbar, and then
use the Holder-Cable to organise any cables.
DIO IN
L AU
DIGITAICAL)
(OPT
ESS
WIREL
8. Slide the Soundbar down as shown below so
that the Bracket-Wall Mounts rest securely
R
POWET
OU
(For TV)
R
POWE
IN
on the Holder-Screws.
•• Insert the Holder-Screws into the wide
Holder-Cable
(bottom) part of the Bracket-Wall
USB
Mounts, and then slide the Bracket-Wall
HDMI
Mounts down so that Bracket-Wall
Mounts rest securely on the
DIO IN
L AU
DIGITAICAL)
(OPT
ESS
WIREL
Holder-Screws.
AUX
R
POWET
OU
)
(For TV
R
POWE
IN
Wi-Fi SETUP
USB
(5V 0.5A)
HDMI
L AUDIO
DIGITA AL)
(OPTIC
IN
SS
WIRELE
AUX
POWER
OUT
(For TV)
POWER
IN
ENG - 29
A)
(5V 0.5
IN
IN
OUT
)
HDMI
(TV-ARC
SPK ADD
IN
IN
OU
HDMI
RC
(TV-A
11 TROUBLESHOOTING
Before seeking assistance, check the following.
The unit will not turn on.
Cannot connect to the TV.
Is the power cord plugged into the outlet?
If connected via a wired network
;; Connect the power plug to the outlet.
;; Check if the cable is connected correctly.
(Check the port name to make sure that
A function does not work when the button
is pressed.
the cable is connected to the correct port.)
(See the corresponding page regarding
each connection method.)
Is there static electricity in the air?
;; Press the
;; Disconnect the power plug and connect it
(Source) button on the right
side of the Soundbar or on the remote
again.
control to check if the mode is correct.
Sound dropouts occur in BT mode.
If connected via a wireless network
;; Connected via Bluetooth
;; See the Bluetooth connection sections on
1. Switch the Soundbar to “BT PAIRING”
pages 9 and 17.
mode, and then use the TV to search
Sound is not produced.
again. (See page 9 for details.)
;; Connected via Wi-Fi
Is the Mute function on?
1. Check if the TV is a compatible model.
;; Press the VOL button to cancel the
•• Only Samsung smart TVs released
function.
after 2014 are supported.
Is the volume set to minimum?
2. Check if the TV is connected to Wi-Fi.
;; Adjust the Volume.
•• If the TV is not connected to Wi-Fi, use
The remote control does not work.
the network menu on the TV to
establish a connection. (See the TV
Are the batteries drained?
user manual.)
;; Replace with new batteries.
Is the distance between the remote control and
Soundbar main unit too far?
;; Move the remote control closer to the
Soundbar main unit.
ENG - 30
3. Check if the Soundbar is connected to
Wi-Fi.
The terms HDMI and HDMI High-Definition
•• When connected, the Soundbar is
Multimedia Interface, and the HDMI Logo are
found in the list of speakers when
Samsung Multiroom app is run on the
mobile device (e.g. smartphone or
trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other
countries.
tablet). (See page 20 for details.)
4. Check for a DFS channel.
•• If your wireless router (Wi-Fi) is using a
•• The Spotify Software is subject to third
party licences found here :
www.spotify.com/connect/third-partylicenses.
•• For more information about Spotify
Connect, please visit
www.spotify.com/connect
DFS channel, you cannot establish a
Wi-Fi connection between the TV and
Soundbar. Contact your Internet
service provider for details.
12 LICENCE
13 OPEN SOURCE
LICENCE NOTICE
Manufactured under license from Dolby
Laboratories. Dolby, Dolby Audio, Pro Logic,
and the double-D symbol are trademarks of
Dolby Laboratories.
For further information on Open Sources used in
this product, please visit the website:
http://opensource.samsung.com
For DTS patents, see http://patents.dts.com.
Manufactured under license from DTS
Licensing Limited. DTS, the Symbol, DTS in
combination with the Symbol, and DTS 2.0
Channel are registered trademarks or
trademarks of DTS, Inc. in the United States
and/or other countries. © DTS, Inc. All Rights
Reserved.
ENG - 31
14 IMPORTANT NOTES ABOUT SERVICE
Figures and illustrations in this User Manual are provided for reference only and may differ from actual
product appearance.
15 SPECIFICATIONS AND GUIDE
Specifications
GENERAL
USB
5V/0.5A
Weight
5.0 kg
Dimensions
(W x H x D)
890.0 x 71.0 x 130.5 mm
Operating Temperature Range
+5°C to +35°C
Operating Humidity Range
10 % ~ 75 %
Speaker
Woofer x 4, Tweeter x 2, 4ohm
Supported play formats
(DTS 2.0 sound is played in DTS format.)
LPCM 2ch, Dolby Audio™ (supporting
Dolby® Digital), DTS
NOTES
•• Samsung Electronics Co., Ltd reserves the right to change the specifications without notice.
•• Weight and dimensions are approximate.
•• For more information about the power supply and power consumption, refer to the label attached
to the product. (Label : Bottom of the Soundbar Main Unit)
ENG - 32
安全資訊
安全警告
警告
為防止電擊,請勿拆卸蓋板 (或背板)。
本機內部無使用者可以自行維修的零件。如
需維修,請由專門的服務人員進行維修。
注意
為防止電擊,請勿打開。
此符號表示內部存在高電壓。 以
任何形式接觸本產品的任何內部部
件都很危險。
此符號表示本產品隨附有關操作和
維護的重要資料。
II 類產品:此符號表示不需要連接
接地。
AC 電壓:此符號表示額定電壓的
標記為 AC 電壓。
• 請勿將本機暴露在雨中或潮濕場所,以
免火災或電擊。
注意
• 為防止電擊,請將寬片插頭完全插入匹
配的寬插槽。
• 本設備應始終連接到帶有保護地線連接
的交流電插座。
• 設備與電源斷開連接時,必須將插頭從
電源插座上拔出,因此電源插頭應隨時
保持便於操作。
• 請勿將水滴落或噴灑在設備上,不得在
設備上放置裝有液體的物品,如花瓶。
• 要完全關閉本設備,須將電源插頭從牆
上電源插座拔出。因此,電源插頭應隨時
保持便於操作。
DC 電壓:此符號表示額定電壓的
標記為 DC 電壓。
注意,使用時需參照說明指示:此
符號指示用戶查閱使用者手冊以取
得進一步的安全相關資訊。
HKG - ii
注意事項
1. 請確保您家中的交流電源符合產品背面
標示貼紙上的要求。請將產品安裝在水
平,適當的基座 (家具) 上,並在周邊留
下足夠的通風空間 7~10 公分。確保通
風孔未被堵塞。請勿將本設備放在放大
器或其他會發熱的設備上。本設備可供
連續使用。要完全斷開設備的電源連
接,請從牆上電源插座上拔掉交流電插
頭。如果長時間不使用設備,請拔下其
電源插頭。
2. 在雷雨天氣時,請從牆上電源插座拔下
交流電插頭。閃電造成的電壓峰值會損
壞本設備。
3. 請勿將本設備直接在陽光下暴曬或暴露
於其他熱源下。這可能導致本設備過熱
而發生故障。
4. 本產品應避免接觸潮濕 (如花瓶) 以及
過熱 (如壁爐) 或者會產生強磁或電場
的設備。如果設備發生故障,請從交流
電源拔下電源線。本產品並非供工業使
用,而是僅供個人使用。如果本產品存
放在低溫環境中,則可能會出現冷凝現
象。如果在冬天將本設備運送到室內,
則需要等待大約 2 小時的時間,以便本
機在使用前達到室內溫度。
5. 本產品使用的電池含有對環境有害的化
學物質。請勿將電池作為普通生活垃圾
棄置。請勿將電池置於火中。請勿使電
池短路,分解或過熱。如果沒有正確替
換電池,可能會導致危險。僅可使用同
樣或相同類別的電池替換。
關於本手冊
使用者手冊分為兩個部分:本簡單的紙張使
用者手冊,以及可下載的詳盡完整手冊。
使用者手冊
參閱本手冊以取得安全指引、產品安裝、
元件、連接和產品規格。
完整手冊
您可以掃描二維碼並前往 Samsung 網
上客戶支援中心,以查看完整手冊。如要
在電腦或流動裝置上查看手冊,請從網
站下載手冊的文件版本。
(http://www.samsung.com/support)
設計和規格以及「應用程式」畫面可能會隨時
變更,恕不另行通知。
HKG - iii
目錄
01
查看元件
02
產品概覽
03
04
使用遙控器前插入電池 (2 粒 AA 電池)
3
------------------------- 3
Soundbar 底部面板
------------------------- 4
連接電源
------------------------- 5
連接 Soundbar
5
7
連接至電視
方法 1。透過連接線連接
------------------------- 7
------------------------- 7
------------------------- 8
– 使用光纖線連接
方法 2。無線連接
------------------------- 9
------------------------- 9
– 透過藍牙連接電視
06
------------------------- 2
前方面板 / Soundbar 右側面板
– 使用 HDMI 線連接電視
05
2
– 透過 Wi-Fi 連接
------------------------- 11
13
連接外部裝置
使用 HDMI 線連接
使用光纖或模擬音訊 (AUX) 線連接
連接 USB
HKG - iv
------------------------- 13
------------------------- 14
15
07
08
17
連接流動裝置
方法 1。透過藍牙連接
方法 2。透過 Wi-Fi 連接 (無線網絡)
使用遙控器
10
使用電視遙控器調整 Soundbar 音量
------------------------- 25
27
安裝墻壁安裝托架
------------------------- 27
------------------------- 27
------------------------- 29
組裝集線器
13
14
15
------------------------- 26
26
軟件更新
墻壁安裝托架元件
12
22
------------------------- 22
安裝注意事項
11
------------------------- 20
使用遙控器的方法
使用隱藏按鈕
09
------------------------- 17
30
解決疑難
31
授權
31
開源軟件許可聲明
32
有關維修的重要說明
32
規格和指南
------------------------- 32
規格
HKG - v
01 查看元件
SMART
MODE
Surround
SOUND
MODE
VOL
BASS
SOUNDBAR
Soundbar 主設備
電源線
HDMI 線
遙控器/電池
集線器
螺絲
• 如需瞭解 Soundbar 掛牆元件,請參閱第 27 頁。
• 請參閱第 29 頁以取得集線器使用方法的指引。
• 如欲購買額外元件或選用的連接線,請聯絡 Samsung 服務中心或 Samsung 客戶服務
中心。
• 配件的外觀與上圖可能有些不同。
使用遙控器前插入電池 (2 粒 AA 電池)
向箭咀方向滑動電池蓋,直至電池蓋完全移除。以正確電極方向插入 2 粒 AA 電池 (1.5V)。
將電池蓋滑動至原來位置。
HKG - 2
02 產品概覽
前方面板 / Soundbar 右側面板
擺放產品,讓 Samsung 標誌位於
Soundbar 右側
上方。
顯示螢幕
顯示產品狀態和目前模式。
-/+ (音量) 按鈕
調整音量。
• 調整時,音量會在 Soundbar 的前方顯示螢幕上出現。
(來源) 按鈕
選擇來源輸入模式。
輸入模式
顯示螢幕
光纖數位輸入
D.IN
ARC (HDMI OUT) 輸入
D.IN  TV ARC (自動轉換)
HDMI 輸入
HDMI
AUX 輸入
AUX
Wi-Fi 模式
WIFI
BLUETOOTH 模式
BT
USB 模式
USB
• 如要開啟「BT PAIRING」模式,將來源變更為「BT」模式,然後按住
(來源) 按鈕超過 5 秒。
(電源) 按鈕
開啟或關閉電源。
HKG - 3
• 插入交流電電源線時,電源按鈕會在 4 至 6 秒後開始運作。
• 開啟本設備時,您需要等待 4 至 5 秒才會聽到聲音。
• 如果您只想透過 Soundbar 聆聽音訊,則必須在電視的「自動設定」選單中關閉電視揚
聲器。請參閱您電視隨附的使用者手冊。
Soundbar 底部面板
POWER
OUT
(For TV)
POWER
IN
DIGITAL AUDIO IN
(OPTICAL)
WIRELESS
AUX IN
DIGITAL AUDIO IN
(OPTICAL)
HDMI IN
HDMI OUT
(TV-ARC)
USB (5V 0.5A)
POWER
OUT
(For TV)
USB (5V 0.5A)
Wi-Fi SETUP SPK ADD
HDMI IN
WIRELESS
POWER
IN
AUX IN
HDMI OUT
(TV-ARC)
Wi-Fi SETUP SPK ADD
POWER OUT (For TV)
連接 Soundbar 至 Samsung TV 的電源線,並使用掛牆套件 (WMN300SB - 未提供) 安
裝在牆面上。
POWER IN
連接 Soundbar 的 AC 電源線。
DIGITAL AUDIO IN (OPTICAL)
連接至外部裝置的數位 (光纖) 輸出。
WIRELESS
將連接 Soundbar 的無線加密狗無線連接至環迴揚聲器和低音炮。
(環迴揚聲器、低音炮和無線加密狗均獨立發售。)
• WIRELESS 插孔並非兼容 USB。
• 低音炮的供應情況視乎地區而定。可以前往 http://www.samsung.com/support 查看供
應情況。
HKG - 4
AUX IN
連接至外部裝置的模擬輸出。
USB (5V 0.5A)
在此連接 USB 裝置,即可透過 Soundbar 播放 USB 裝置上的音樂檔案。
HDMI IN
使用 HDMI 線同時輸入數碼視頻和音頻訊號。
連接至外部裝置的 HDMI 輸出。
HDMI OUT (TV-ARC)
連接至電視上的 HDMI (ARC) 插孔。
Wi-Fi SETUP / SPK ADD
透過 Samsung Multiroom 應用程式連接至無線網絡 (Wi-Fi)。
• 從牆上插座斷開電源線連接時,拔出插頭。不要拉扯電源線。
• 元件之間完成所有連接之前,不要將本設備或其他元件連接至交流電插座。
03 連接 SOUNDBAR
連接電源
• 如需更多有關電源功率需求和耗電資料,請參閱產品標籤。
(標籤:Soundbar 主設備底部)
• 將隨附的電源線連接至 POWER IN 插
孔。
電源線
POWER
IN
USB (5V 0.5A)
連接電源
POWER
OUT
(For TV)
DIGITAL AUDIO IN
(OPTICAL)
HDMI IN
WIRELESS
POWER
IN
AUX IN
HDMI OUT
(TV-ARC)
Soundbar
主設備的底部
HKG - 5
POWER
OUT
(For TV)
POWER IN
USB (5V 0.5A)
POWER
OUT
(For TV)
DIGITAL AUDIO IN
(OPTICAL)
• POWER OUT 插孔用作向使用掛牆套
件 (WMN300SB – 未提供) 之掛牆
Samsung TV 提供電力。
• POWER OUT 插孔只可連接至使用
2 針電源線且耗電量為 400 W 以下的
Samsung TV。(將插孔連接至耗電量超
過 400 W 的裝置可能會損壞 Soundbar
或引致故障。)
HDMI IN
WIRELESS
POWER
IN
AUX IN
HDMI OUT
(TV-ARC)
Soundbar 主設備的底部
如需兼容 WMN300SB 掛牆套件和
POWER OUT 插孔的 Samsung TV 清
單,請參閱 WMN300SB 掛牆套件使用
者手冊。您可以在網上查看手冊:
http://www.samsung.com/support。
HKG - 6
04 連接至電視
透過有線和無線連接在 Soundbar 上收聽電視聲音。
• Soundbar 連接至指定的 Samsung 電視後,您便可使用電視遙控器控制 Soundbar。
– 使用光纖連接線時,支援藍牙的 2017 Samsung Smart TV 可支援此功能。
– 此功能亦讓您使用電視選單調整音場和各種設定,以及音量和靜音。
方法 1。透過連接線連接
使用 HDMI 線連接電視
Soundbar 底部
連接至電視的 HDMI IN
(ARC) 埠。
HDMI IN
HDMI IN
(ARC)
HDMI 線
HDMI OUT
(TV-ARC)
連接至 Soundbar 主設備的
HDMI OUT (TV-ARC) 埠。
TV
ARC
Soundbar 右側
1. 開啟 Soundbar 和電視後,按照圖解所示連接 HDMI 線。
2. 「TV ARC」在 Soundbar 主設備的顯示螢幕上出現,而 Soundbar 會播放電視聲音。
• 若聽不到電視聲音,按下遙控器或 Soundbar 右側的
(來源) 按鈕,以切換至
「D.IN」模式。螢幕會按序顯示「D.IN」和「TV ARC」,而電視聲音會播放。
HKG - 7
• 如果「TV ARC」沒有出現在 Soundbar 主設備的顯示螢幕上,請確定連接線已插入
正確的連接埠。
• 使用電視遙控器上的音量按鈕變更 Soundbar 音量。
備註
• HDMI 是以單一接頭進行影片和音訊資料數碼傳輸的介面。
• 若電視配備 ARC 連接埠,將 HDMI 線連接至 HDMI IN (ARC) 連接埠。
• 我們建議您盡可能使用無芯 HDMI 線。如果您使用帶芯 HDMI 線,請使用直徑少於
14 毫米的 HDMI 線。
• Anynet+ 必須開啟。
• 若 HDMI 線不支援 ARC,此功能將無法使用。
使用光纖線連接
Soundbar 底部
DIGITAL AUDIO IN
(OPTICAL)
OPTICAL OUT
光纖線
(未提供)
WIRELESS
AUX IN
D.IN
Soundbar 右側
1. 使用數位光纖連 (未提供) 接線連接 Soundbar 上的 DIGITAL AUDIO IN (OPTICAL)
插孔和電視的 OPTICAL OUT 插孔。
2. 按下右側面板或遙控器上的
(來源) 按鈕,然後選擇模式“D.IN”
。
Auto Power Link
Auto Power Link 會在開啟電視時自動開啟 Soundbar。
1. 使用數位光纖 (未提供) 電纜將 Soundbar 連接至電視。
2. 按下右側面板或遙控器上的
(來源) 按鈕,然後選擇「D.IN」。
HKG - 8
3. 按下遙控器上的左按鈕 5 秒,以開啟或關閉 Auto Power Link。
• Auto Power Link 預設為 ON。
(如要關閉此功能,可使用 Soundbar 關閉 Auto Power。)
• Auto Power Link 可能無法運作,視乎已連接的裝置而定。
• 此功能只適用於「D.IN」模式。
方法 2。無線連接
透過藍牙連接電視
透過藍牙連接電視時,您可以欣賞立體聲,而無需因處理纜線而煩惱。
• 只可同時連接一部電視。
初始連接
1. 按下右側面板或遙控器上的
(來源) 按鈕,然後選擇「BT」。
2. 將「BT」變更為「BT PAIRING」。
• 如果出現「BT READY」,按住 Soundbar 右側面板或遙控器上的
(來源) 按鈕超
過 5 秒,以顯示「BT PAIRING」。
3. 在電視上選擇藍牙模式。(如需瞭解詳情,請參閱電視手冊。)
4. 從電視螢幕上的清單選擇「[AV] Samsung Soundbar MSxxx」。
可用的 Soundbar 會在電視藍牙裝置清單上顯示為「Need Pairing」或「Paired」。
如要連接 Soundbar,選擇訊息並建立連接。
• 電視連接後,[電視名稱] →「BT」會在 Soundbar 前方顯示螢幕上出現。
5. 您現在可以聽到 Soundbar 播放電視聲音。
HKG - 9
若裝置無法連接
• 如果先前連接的 Soundbar (例如「[AV] Samsung Soundbar MSxxx」) 在清單上出
現,請將它刪除。
• 在「BT」模式下,按住 Soundbar 右側面板或遙控器上的
(來源) 按鈕超過 5 秒,以
切換至「BT PAIRING」模式。然後,從電視搜尋清單上選擇「[AV] Samsung
Soundbar MSxxx」。
什麼是「BT READY」和「BT PAIRING」狀態?
• BT READY : 在這個模式下,您可以搜尋先前連接的電視,或從先前連接的流動裝置連
接 Soundbar。
• BT PAIRING : 在這個模式下,您可以連接至新裝置。(在「BT」模式下,按住 Soundbar
右側或遙控器上的
(來源) 按鈕超過 5 秒。)
備註
• 如果系統在連接藍牙裝置時要求輸入 PIN 碼,請輸入 <0000>。
• 在藍牙連接模式下,若 Soundbar 和藍牙裝置相距超過 10 米,藍牙連接會中斷。
• 在待機狀態下,Soundbar 會在 5 分鐘後自動關閉。
• 在以下情況下,Soundbar 可能不會執行藍牙搜尋,或正確連接:
– 若 Soundbar 附近的電場強烈。
– 若數部藍牙裝置同時配對至 Soundbar。
– 若藍牙裝置已關閉、不存在或發生故障。
• 電子裝置可能會導致無線電干擾。發放電磁波的裝置必須與 Soundbar 主設備保持遠
距離,當中包括微波爐、無線 LAN 裝置等。
從電視解除連接 Soundbar
按下右側面板或遙控器上的
(來源) 按鈕,然後切換至「BT」以外的模式。
• 電視必須從 Soundbar 接收回應,因此解除連接過程需要时间。
(所需時間可能有所不同,視乎電視型號而定。)
• 如要取消 Soundbar 和電視之間的自動藍牙連接,可在「BT READY」狀態下按遙控器
上的 p (播放/暫停) 按鈕 5 秒。(切換 開 → 關)
HKG - 10
透過 Wi-Fi 連接
連接前檢查清單
1. 確認於 2014 年後推出的 Samsung Smart TV。此功能只與 2014 年以後推出的
Samsung Smart TV 兼容。
2. 確定您的無線路由器 (Wi-Fi) 已準備就緒並正在運作。
3. 確定電視已連接至無線路由器 (您的 Wi-Fi 網絡)。
第 1 步:將 Soundbar 連接至 Wi-Fi
1. 按 Soundbar 右側或遙控器上的
(來源) 按鈕以選擇「WIFI」模式。
• 使用指定的 Samsung TV (支援藍牙的 2016 或 2017 Samsung smart TV)。
– 若您在電視開啟時選擇「WIFI」模式,電視螢幕會顯示彈出視窗,向您提供將
Soundbar 自動連接至無線路由器 (Wi-Fi) 的指示。請參閱電視彈出視窗上的指
示。
WIFI
2. 將您的流動裝置 (智能手機、平板電腦等) 連接至與電視相同的 Wi-Fi 網絡。
3. 在流動裝置 (智能手機、平板電腦等) 上安裝和啟動 Samsung Multiroom 應用程式。
Samsung Multiroom 應用程式
Android
iOS
4. 按照流動裝置應用程式螢幕上的指示將 Soundbar 連接至 Wi-Fi 網絡。
HKG - 11
第 2 步:配置電視上的設定
• 將輸入來源變更為 Soundbar 後,若電視從您的無線網絡中斷連接,請使用電視選單將
電視再次連接至網絡。
對於 2017 年推出的電視:
1. 首頁功能表 → 設定 ( )  音效  音效輸出  選擇 [AV] Soundbar MSxxx (Wi-Fi)
2. Soundbar 輸出電視聲音。
對於 2016 年推出的電視:
1. 首頁功能表  設定 ( )  音效  音效輸出  選擇 [AV] Samsung Soundbar
MSxxx (Wi-Fi)
2. Soundbar 輸出電視聲音。
對於 2015 年推出的電視:
1. 首頁功能表  音效  揚聲器列表  選擇 [AV] Samsung Soundbar MSxxx (Wi-Fi)
2. Soundbar 輸出電視聲音。
對於 2014 年推出的電視:
1. 首頁功能表  音效  揚聲器設定  選擇 Multiroom Link - 設定 
Soundbar+Surround.
2. 在 Soundbar 選單項目中,選擇「[AV] Samsung Soundbar MSxxx」,然後選擇
「確定」。
3. 首頁功能表  音效  揚聲器設定  選擇電視音效輸出  Multiroom Link
揚聲器設定
Multiroom Link
電視音效輸出
電視揚聲器
• 電視安裝類型
TV SoundConnect
• Samsung 音頻裝置清單
• 新增裝置
Multiroom Link
• 設定
3
Multiroom Link
Soundbar+Surround
直立式
Soundbar
開啟
Soundbar+Surround
藍牙耳機
• 藍牙耳機清單
確定
[AV] Samsung Soundbar MSxxx [AV] Samsung Soundbar MSxxx
c
1
2
不使用
確定
音量大小
揚聲器測試
名稱編
4. Soundbar 輸出電視聲音。
備註
• 電視和 Soundbar 必須連接至相同無線網絡 (Wi-Fi)。
• 若您的無線路由器 (Wi-Fi) 使用 DFS 頻道,您將無法在電視和 Soundbar 之間建立
Wi-Fi 連線。聯絡您的網際網路服務提供者瞭解詳情。
• 若 5GHz Wi-Fi 連線並不流暢,請使用 2.4GHz 頻寬。
HKG - 12
05 連接外部裝置
透過有線或無線網絡連接至外部裝置,以透過 Soundbar 播放外部裝置的聲音。
使用 HDMI 線連接
外部裝置
Soundbar 底部
HDMI IN
HDMI OUT
HDMI 線
HDMI OUT
(TV-ARC)
HDMI IN
(ARC)
HDMI 線
HDMI
Soundbar 右側
1. 使用 HDMI 線從產品背部的 HDMI IN 插孔連接至您數碼裝置上的 HDMI OUT 插孔。
2. 使用 HDMI 線從產品背部的 HDMI OUT (TV-ARC) 插孔連接至您電視上的 HDMI IN
插孔。
3. 按下右側面板或遙控器上的
(來源) 按鈕,然後選擇「HDMI」。
4. 「HDMI」模式會在 Soundbar 顯示面板上顯示,而聲音會播放。
HKG - 13
使用光纖或模擬音訊 (AUX) 線連接
Soundbar 右側
BD / DVD 播放機 / 機頂盒 /
遊戲機
OPTICAL OUT
DIGITAL AUDIO IN
(OPTICAL)
光纖線
(未提供)
WIRELESS
或
R - AUDIO - L
AUX IN
音訊 (AUX) 線
(未提供)
Soundbar 底部
光纖線
X 使用數位光纖連 (未提供) 接線連接主設備上的 DIGITAL AUDIO IN (OPTICAL) 和外
部裝置的 OPTICAL OUT 插孔。
Y 按下右側面板或遙控器上的
(來源) 按鈕,以選擇「D.IN」模式。
或
音訊 (AUX) 線
X 使用音頻線連接主設備上的 AUX IN (音訊) 和外部裝置的 AUDIO OUT 插孔。
Y 按下右側面板或遙控器上的
(來源) 按鈕,以選擇「AUX」模式。
HKG - 14
06 連接 USB
您可以透過 Soundbar 播放位於 USB 儲存裝置上的音樂檔案。
USB 埠
USB (5V 0.5A)
POWER
OUT
(For TV)
DIGITAL AUDIO IN
(OPTICAL)
顯示螢幕
Wi-Fi SETUP SPK ADD
HDMI IN
WIRELESS
POWER
IN
AUX IN
HDMI OUT
(TV-ARC)
USB
USB (5V 0.5A)
1.
2.
3.
4.
將 USB 裝置連接至產品背部的 USB 連接埠。
按下右側面板或遙控器上的
(來源) 按鈕,然後選擇「USB」。
「USB」會顯示在螢幕上。
透過 Soundbar 播放 USB 儲存裝置上的音樂檔案。
• 若沒有 USB 裝置連接超過 5 分鐘,Soundbar 會自動關閉 (自動電源關閉)。
HKG - 15
檔案格式類型相容性清單
延長線
編碼
取樣率
位元率
*.mp3
MPEG 1 Layer2
16KHz ~ 48KHz
80kbps~320kbps
MPEG 1 Layer3
16KHz ~ 48KHz
80kbps~320kbps
MPEG 2 Layer3
16KHz ~ 48KHz
80kbps~320kbps
MPEG 2.5 Layer3
16KHz ~ 48KHz
80kbps~320kbps
Wave_Format_MSAudio1
16KHz ~ 48KHz
56kbps~128kbps
Wave_Format_MSAudio2
16KHz ~ 48KHz
56kbps~128kbps
AAC
16KHz ~ 96KHz
48kbps~320kbps
AAC-LC
16KHz ~ 96KHz
128kbps~192kbps
5.1ch 320kbps
HE-AAC
24KHz ~ 96KHz
*.wav
48kbps~64kbps
5.1ch 160kbps
-
16KHz ~ 48KHz
最高 3000kbps
*.flac
OGG 1.1.0
16KHz ~ 48KHz
50kbps~500kbps
FLAC 1.1.0,FLAC 1.2.1
16KHz ~ 96KHz
最高 3000kbps
*.wma
*.aac
*.ogg
• 若 USB 裝置儲存太多資料夾和檔案,Soundbar 可能需要一段時間來存取和播放檔案。
HKG - 16
07 連接流動裝置
方法 1。透過藍牙連接
透過藍牙連接流動裝置時,您可以欣賞立體聲,而無需因處理纜線而煩惱。
• 您不可同時連接多部藍牙裝置。
藍牙裝置
初始連接
1. 按下右側面板或遙控器上的
(來源) 按鈕,然後選擇「BT」。
2. 將「BT」變更為「BT PAIRING」。
• 如果出現「BT READY」,按住 Soundbar 右側面板或遙控器上的
(來源) 按鈕超
過 5 秒,以顯示「BT PAIRING」。
3. 從清單選擇「[AV] Samsung Soundbar MSxxx」。
• Soundbar 連接至藍牙裝置後,[藍牙裝置名稱] →「BT」會在前方螢幕上出現。
4. 透過 Soundbar 及藍牙連接播放裝置上的音樂檔案。
若裝置無法連接
• 如果先前連接的 Soundbar (例如「[AV] Samsung Soundbar MSxxx」) 在清單上出
現,請將它刪除。
• 在「BT」模式下,按住 Soundbar 右側面板或遙控器上的
(來源) 按鈕超過 5 秒,以
切換至「BT PAIRING」模式。然後,從藍牙裝置搜尋清單上選擇「[AV] Samsung
Soundbar MSxxx」。
HKG - 17
什麼是「BT READY」和「BT PAIRING」狀態?
• BT READY : 在這個模式下,您可以搜尋先前連接的電視,或從先前連接的流動裝置連
接 Soundbar。
• BT PAIRING : 在這個模式下,您可以連接至新裝置。(在「BT」模式下,按住 Soundbar
右側或遙控器上的
(來源) 按鈕超過 5 秒。)
備註
• 如果系統在連接藍牙裝置時要求輸入 PIN 碼,請輸入 <0000>。
• 在藍牙連接模式下,若 Soundbar 和藍牙裝置相距超過 10 米,藍牙連接會中斷。
• 在待機狀態下,Soundbar 會在 5 分鐘後自動關閉。
• 在以下情況下,Soundbar 可能不會執行藍牙搜尋,或正確連接:
– 若 Soundbar 附近的電場強烈。
– 若數部藍牙裝置同時配對至 Soundbar。
– 若藍牙裝置已關閉、不存在或發生故障。
• 電子裝置可能會導致無線電干擾。發放電磁波的裝置必須與 Soundbar 主設備保持遠
距離,當中包括微波爐、無線 LAN 裝置等。
• Soundbar 支援 SBC 資料 (44.1kHz、48kHz)。
• 只連接支援 A2DP (AV) 功能的藍牙裝置。
• 您不可將 Soundbar 連接至只支援免提功能的藍牙裝置。
• 將 Soundbar 配對至藍牙裝置後,從裝置的掃描裝置清單選擇「[AV] Samsung
Soundbar MSxxx」,Soundbar 便會自動切換至「BT」模式。
– 只在 Soundbar 出現在藍牙裝置的配對裝置清單時可用。
(藍牙裝置和 Soundbar 必須曾經配對最少一次。)
• 只有 Soundbar 顯示「BT READY」時,Soundbar 才會在藍牙裝置的搜尋裝置清單上
出現。
• 使用藍牙功能時,Soundbar 不可與另一部藍牙裝置配對。
HKG - 18
從 Soundbar 解除連接藍牙裝置
您可以從 Soundbar 解除連接藍牙裝置。如需指引,請參閱藍牙裝置的使用者手冊。
• Soundbar 將會解除連接。
• Soundbar 從藍牙裝置解除連接後,Soundbar 的顯示螢幕上會顯示
「BT DISCONNECTED」。
從藍牙裝置解除連接 Soundbar
按下右側面板或遙控器上的
(來源) 按鈕,然後將模式變更為「BT」以外的模式。
• 由於藍牙裝置必須接收 Soundbar 的回應,因此解除連接需要時間。(解除連接的時間
可能有異,視乎藍牙裝置而定)
• Soundbar 從藍牙裝置解除連接後,Soundbar 的顯示螢幕上會顯示
「BT DISCONNECTED」。
備註
• 在藍牙連接模式下,若 Soundbar 和藍牙裝置相距超過 10 米,藍牙連接會中斷。
• 在準備就緒狀態下,Soundbar 會在 5 分鐘後自動關閉。
更多有關藍牙的資訊
藍牙是讓支援藍牙的裝置在短距離之間互相無線連接的技術。
• 在以下情況,藍牙裝置可能會發出噪音或發生故障,視乎使用情況而定:
– 您的身體部分接觸藍牙裝置的接收/傳輸系統或 Soundbar。
– 裝置會受障礙物 (例如牆壁,角落或區域分隔物) 而引致的電磁變化影響。
– 裝置暴露於頻帶相同的裝置的電磁干擾下,其中包括醫療設備、微波爐和無線
LAN。
• 將 Soundbar 與藍牙裝置靠近並配對。
• Soundbar 和藍牙裝置相隔愈遠,品質愈低。
若距離超出藍牙操作範圍,連接便會中斷。
• 在接收較差的地方,藍牙連接可能無法正常運作。
• 只有裝置靠近時,藍牙連接才可正常運作。若藍牙裝置超出範圍,連接會自動中斷。即使
在範圍內,音質亦可能會因障礙物 (例如牆或門) 而下降。
• 此無線裝置可能會在運作期間引致電磁干擾。
HKG - 19
方法 2。透過 Wi-Fi 連接 (無線網絡)
• 將單一 Soundbar 連接至 Wi-Fi 以存取各種音樂串流服務和互聯網電台。將多個
Soundbar 連接至 Wi-Fi 以使用群組播放功能或立體聲模式。
• 如要透過無線網絡 (Wi-Fi) 將 Soundbar 連接至流動裝置,您必須使用 Samsung
Multiroom 應用程式。
流動裝置
初始連接
1. 按 Soundbar 右側或遙控器上的
(來源) 按鈕以選擇「WIFI」模式。
WIFI
2. 在流動裝置 (例如,智能手機或平板電腦) 上安裝和啟動 Samsung Multiroom 應用程
式。
Samsung Multiroom 應用程式
Android
iOS
3. 按照流動裝置應用程式螢幕上的指示將 Soundbar 連接至 Wi-Fi。
HKG - 20
Samsung 無線揚聲器使用時安裝其他 Soundbar
1. 在 Samsung Multiroom 應用程式的首頁螢幕,選擇頂部的 設定 (
「Add Speaker」。
),然後選擇
2. 如要將 Soundbar 連接至 2 個 Samsung 無線揚聲器並配置環迴聲系統,請按照以下
步驟執行。(您不可使用一部音效裝置和一部 Soundbar 設定環迴音系統。)
X 輕觸 即可前往所有揚聲器的清單。
Y 輕觸 Soundbar 型號名稱右方的 。
Z 輕觸 Surround Setup。將揚聲器拖動至理想位置後,選擇 Done。
[ 環迴音效連接已完成。
Soundbar
備註
• 如要連接額外 SWA-9000S (未提供),請從 Soundbar 解除連接 Samsung 無線揚聲
器,以停用環迴音系統。(如果您連接環迴音系統,而不解除連接 SWA-9000S,聲音會
透過 Samsung 無線揚聲器和環迴揚聲器播放。)
HKG - 21
08 使用遙控器
使用遙控器的方法
開啟和關閉 Soundbar。
電源
聲音控制
您可以從 TREBLE、SYNC、REAR
LEVEL 或 REAR SPEAKER ON/OFF
選擇。
• 如要調整 TREBLE 音量,選擇聲音控
制 TREBLE,然後使用上/下按鈕在
-6 至 +6 之間調整音量。
• 按住
SMART
MODE
Surround
每個頻帶的聲音。您可以透過左/右選
擇 150Hz、300Hz、600Hz、1.2KHz、
2.5KHz、5KHz 和 10KHz,並透過上/
SOUND
MODE
下在 -6 至 +6 之間調整每個頻率。
VOL
(聲音控制) 按鈕 5 秒以調整
BASS
Surround
Surround
• 若電視機與
Soundbar 之間的視訊或
Bluetooth
POWER
Bluetooth
音訊未能同步,
在聲音控制中選擇
POWER
SYNC,然後使用上/下按鈕設定 0 到
SOUNDBAR
SOUND
MODE
SOUND
MODE
300 毫秒的音訊延遲。(「USB」模式
除外)
• 若已連接環迴揚聲器 (未提供),選擇
REAR LEVEL,然後使用上/下按鈕在
-6 至 +6 之間調整音量。
您可以使用上/下按鈕將 REAR
VOL
VOL
HKG - 22
SPEAKER 功能設定為 ON/OFF。
WOOFER
• 音訊同步只適用於部分功能。
WOOFER
環迴音效功能可增加聲音的深度和空間感。每次按下此按鈕,ON 和 OFF 會互
Bluetooth
POWER
相替換。
Surround
Surround
Bluetooth
• ON : 透過所有揚聲器播放聲音。
Surround POWER
SOUND• OFF : 您可以從部分揚聲器聽到原本來源聲道的聲音。
MODE
SOUND
MODE
SOUND
MODE
您可以選擇 STANDARD、MUSIC、CLEAR VOICE、SPORTS 或 MOVIE,以
選擇理想的音效。
如果您想享受原來聲音,請選擇「STANDARD」模式。
• DRC (Dynamic Range Control)
讓您在 Dolby Digital 曲目上套用動態範圍控制。如果您在待機模式下按住
SOUND MODE 按鈕,DRC (動態範圍控制) 會開啟或關閉。DRC 開啟時,
VOL
VOL
WOOFER
響亮的聲音會減少。(聲音可能會失真。)
WOOFER
按下以選擇連接至 Soundbar 的來源。
• BT PAIRING 模式
如要在「BT」模式開啟「BT PAIRING」模式,按住
來源
5 秒。請參閱第 17 頁以瞭解詳情。
• Auto Power Down 功能
裝置會在以下情況下自動關閉。
– D.IN / WIFI / BT / USB 模式:若 5 分鐘沒有音訊。
– HDMI 模式:若 15 分鐘沒有音訊。
– AUX 模式:
– 若音頻 (AUX) 線解除連接 5 分鐘。
– 音頻 (AUX) 線連接後,8 小時沒有按鍵輸入。
(Auto Power Down 功能只可在該情況下關閉。)
– 如要關閉 Auto Power Down 功能,請在 「AUX」模式下按住 p 按
鈕 5 秒。「ON-AUTO POWER DOWN」/「OFF-AUTO POWER
DOWN」會在顯示屏上出現。
Bluetooth
POWER
Surround
SOUND
MODE
按下 p 按鈕即可暫停音樂檔案。
若您再次按下按鈕,音樂檔案便會播放。
播放/暫停
(BT/Wi-Fi)
VOL
Surround
WOOFER
Bluetooth
POWER
SOUND
MODE
VOL
(來源) 按鈕超過
WOOFER
HKG - 23
按下指示區域以選擇上/下/左/右。
上/下/左/右
Bluetooth
POWER
Surround
在按鈕上按下上/下/左/右以選擇或設定功能。
SOUND
MODE
• 重覆
如要使用重覆功能,按下向上按鈕。
VOL
• 音樂跳播
WOOFER
按下右按鈕以選擇下一個音樂檔案。按下向左按鈕以選擇上一個音樂檔
案。
• Anynet+ / Auto Power Link
您可以開啟或關閉 Anynet+ 和 Auto Power Link。
SMART
MODE
Surround
SOUND
MODE
VOL
BASS
BA
SS
D
BA
R
N
U
SO
VO
L
Su
rro
un
d
BA
SS
D
BA
R
N
SO
U
VO
L
SO
M UN
OD D
E
SM
M AR
OD T
E
SM
M AR
OD T
E
U
N
D
BA
R
BA
SS
Su
rro
un
d
SO
M UN
OD D
E
BASS
BASS
SO
SO
U
N
D
BA
R
BA
SS
Su
rro
un
d
VOL
SO
M UN
OD D
E
SMART
MODE
SM
M AR
OD T
E
SOUND
MODE
自動優化音效以配合目前播放的場景。模式會在每次按下按鈕時開啟或關閉。
SMART
MODE
VO
L
Surround
Anynet+ 和 Auto Power Link 分別由右和左按鈕控制。
– Anynet+:如果使用 HDMI 線將 Soundbar 連接至 Samsung TV,您
可以使用 Samsung TV 遙控器控制 Soundbar。按住右按鈕 5 秒以將
Anynet+ 切換至 ON 或 OFF。
– Auto Power Link:如果透過數位光纖纜線連接 Soundbar 和電
視,Soundbar 會在您開啟電視時自動開啟。按住左按鈕 5 秒以將
Auto Power Link 切換至 ON 或 OFF。
– Anynet+ / Auto Power Link 預設為開啟。
向上或向下推動按鈕,以在 -6 至 +6 之間調整低音 (BASS) 音量。如要將低
音 (BASS) 的音量設定為 0,請按下按鈕。
• 低音炮 (未提供) 連接後,BASS 按鈕會切換至低音炮鍵。向上或向下推動
按鈕,以將低音炮音量調整至 -12,或在 -6 至 +6 之間調整低音炮音量。
如要將低音炮的音量設定為 0,請按下按鈕。
HKG - 24
BA
SS
向上或向下推動按鈕,以調整音量。
• 靜音
按下 VOL 按鈕以設定為靜音。再次按下按鈕以取消靜音。
使用電視遙控器調整 Soundbar 音量
使用電視選單將 Samsung 電視上的電視揚聲器設為外部揚聲器。
(如需瞭解詳情,請參閱電視使用者手冊。)
• 安裝 Soundbar 後,您可以使用 Samsung 電視隨附的 IR 遙控器調整 Soundbar 的音
量。(如果您不想使用此功能,可在 Soundbar 開啟時按住 Surround 按鈕 5 秒。
「OFF-TV REMOTE」會在 Soundbar 螢幕上出現,而功能會關閉。)如要只使用
Samsung 遙控器調整音量,按住 Surround 按鈕超過 5 秒,直至「SAMSUNG-TV
REMOTE」在 Soundbar 螢幕上出現。
– 每次按住 Surround 按鈕 5 秒時,模式會按以下次序切換:
「SAMSUNG-TV REMOTE」(預設模式) →「OFF-TV REMOTE」→
「ALL-TV REMOTE」。
• 如要使用第三方製造商電視隨附的遙控器調整 Soundbar 音量,請開啟 Soundbar,然
後按下 Surround 按鈕 5 秒。(「OFF-TV REMOTE」在 Soundbar 螢幕上出現),放開
Surround 按鈕,然後再次按住 Surround 按鈕超過 5 秒。(「ALL-TV REMOTE」在
Soundbar 螢幕上出現。)
– 此功能可能無法使用,視乎遙控器而定。
– 支援此功能的製造商:
VIZIO、LG、Sony、Sharp、PHILIPS、PANASONIC、TOSHIBA、GRUNDIG、
Hisense、RCA
HKG - 25
SO
M UN
OD D
E
VO
L
BA
R
VO
L
U
N
D
SO
BA
R
N
D
SO
U
VO
L
Su
rro
un
d
SM
M AR
OD T
E
SM
M AR
OD T
E
SO
M UN
OD D
E
BA
SS
Su
rro
un
d
SO
M UN
OD D
E
Su
rro
un
d
N
D
U
SO
VO
L
BA
R
BA
SS
BASS
SO
M UN
OD D
E
VOL
Su
rro
un
d
VOL
SM
M AR
OD T
E
SM
M AR
OD T
E
使用隱藏按鈕
隱藏按鈕
參考網頁
遙控器按鈕
功能
Surround
電視遙控器開/關
第 25 頁
藍牙配對
第 17 頁
p (播放/暫停)
Auto Power Down 開/關 (AUX 模式)
第 23 頁
左
Auto Power Link ON/OFF
第8頁
右
Anynet+ ON/OFF
第 24 頁
7 頻 EQ
第 22 頁
DRC ON/OFF (備用)
第 23 頁
(來源)
(聲音控制)
SOUND MODE
09 軟件更新
當 Soundbar 連接至互聯網後,即使 Soundbar 已關閉,軟件更新亦會自動執行。
• 如要使用自動更新功能,Soundbar 必須連接至互聯網。若電源線解除連接,或電力中
斷,Soundbar 的 Wi-Fi 連接亦會終止。若電源斷開,開啟 Soundbar 再重新連接。
HKG - 26
10 安裝墻壁安裝托
架
墻壁安裝托架元件
450mm
墻壁安裝托架指示圖
安裝注意事項
• 只在垂直牆上安裝。
• 不要在高溫或潮濕的地方安裝。
• 確定牆壁可承受產品重量。否則,請強化
牆壁或選擇另一個安裝位置。
• 購買或使用您牆壁類型 (石膏板、鐵板、
木材等) 適合的固定螺絲或錨。可行的
話,將支援螺絲固定在牆上的螺柱。
• 根據安裝 Soundbar 的牆壁的類型和厚
度購買牆上的安裝螺絲。
– 直徑:M5
– 長度:建議 35 毫米或以上。
• 在牆上安裝 Soundbar 前,從設備將連
接線連接至外部裝置。
• 安裝前,確定設備已關閉並拔除插頭。
否則,可能會引致觸電。
螺絲固定器 (2 顆)
螺絲 (2 顆)
墻壁安裝托架 (2 顆)
1. 將墻壁安裝托架指示圖貼在牆面。
• 墻壁安裝托架指示圖必須為水平。
• 如果您在牆上安裝電視,Soundbar
應安裝在電視下方最少 5 厘米位
置。
5 厘米或以上
HKG - 27
2. 將模板紙上面的中線對齊電視的中心位
置 (若將 Soundbar 安裝在電視的下方)
,再用膠布將墻壁安裝托架指示圖固定
在牆上。
• 若非安裝於電視下方,請將中線對準
安裝位置的中心。
5. 在每個螺絲固定器中插入一個螺釘
(未提供),再將支架螺釘中的螺釘擰緊。
6. 使用 2 顆螺絲,在 Soundbar 底部的正
確方向安裝 2 顆墻壁安裝托架。
450mm
中線
3. 使用尖銳物件 (例如鋼筆或鉛筆),標記
孔的位置,然後移除 墻壁安裝托架指
示圖。
450mm
CENTER LINE
• 組裝時,確定墻壁安裝托架的掛勾部
分位於 Soundbar 的後方。
Soundbar 後方
4. 用尺寸合適的鉆頭在各標記處鉆孔。
• 若標記與墻體上位置不符,在插入
固定螺釘前,請確定您是否在孔中
插入正確的螺釘或螺栓。若使用螺
釘或螺栓,請確保鉆孔足夠大可以
插入螺釘或螺栓。
HKG - 28
Soundbar 右端
7. 將墻壁安裝托架懸掛在牆上的螺絲固
定器上,即可透過墻壁安裝托架來安裝
Soundbar。
組裝集線器
如圖所示,使用隨附的螺絲將集線器固定在
Soundbar,然後使用集線器整理連接線。
O IN
DI
L AU
DIGITAICAL)
(OPT
ESS
WIREL
8. 向下拉動 Soundbar 如下所示,讓墻壁
安裝托架安全擺放在螺絲固定器上。
• 將螺絲固定器插入墻壁安裝托架的
寬 (底部) 部分,然後向下拉動墻壁安
裝托架,讓墻壁安裝托架安全擺放
在螺絲固定器上。
R
POWET
OU
(For TV)
R
POWE
IN
集線器
USB
HDMI
DIO IN
L AU
DIGITAICAL)
(OPT
ESS
WIREL
AUX
R
POWET
OU
)
(For TV
R
POWE
IN
Wi-Fi SETUP
USB
(5V 0.5A)
HDMI
L AUDIO
DIGITA AL)
(OPTIC
IN
SS
WIRELE
AUX
POWER
OUT
(For TV)
POWER
IN
HKG - 29
A)
(5V 0.5
IN
IN
OUT
)
HDMI
(TV-ARC
SPK ADD
IN
IN
OU
HDMI
RC
(TV-A
11 解決疑難
在尋求幫助前,請檢查以下事項。
設備不會開啟。
無法連接至電視。
電源線是否已插入插座?
; 將電源插頭連接至插座。
若透過有線網絡連接
; 檢查連接線是否已正確連接。(檢查連
接埠名稱,以確保連接線已連接至正
確的連接埠。) (參閱有關每個連接方
法的相應頁面。)
; 按 Soundbar 右側或遙控器上的
(來源) 按鈕以檢查模式是否正確。
按下按鈕時,功能無法運作。
空氣中是否有靜電?
; 解除連接電源插頭並重新連接。
在藍牙模式下,發生聲音遺失問題。
; 查看第 9 和第 17 頁的藍牙連
接部分。
沒有聲音。
靜音功能是否已開啟?
; 按下 VOL 按鈕以取消功能。
音量是否設為最低?
; 調整音量。
遙控器無法運作。
電量是否已耗盡?
; 更換電池。
遙控器和 Soundbar 主設備是否相距太
遠?
; 將遙控器移近 Soundbar 主設備。
若透過無線網絡連接
; 透過藍牙連接
1. 將 Soundbar 切換至「BT PAIRING」
模式,然後使用電視再次搜尋。
(請參閱第 9 頁以瞭解詳情。)
; 透過 Wi-Fi 連接
1. 檢查電視型號是否兼容。
• 只支援 2014 年以後推出的
Samsung smart TV。
2. 檢查電視是否已連接至 Wi-Fi。
• 若電視尚未連接至 Wi-Fi,可使用
電視上的網絡選單建立連線。
(參閱電視使用者手冊。)
HKG - 30
3. 檢查 Soundbar 是否已連接至
Wi-Fi。
• 連接後,當 Samsung Multiroom
應用程式在流動裝置 (例如,智能
手機或平板電腦) 上執行時,您會
在揚聲器清單上看到 Soundbar。
(請參閱第 20 頁以瞭解詳情。)
4. 檢查 DFS 聲道。
• 若您的無線路由器 (Wi-Fi) 使用
DFS 頻道,您將無法在電視和
Soundbar 之間建立 Wi-Fi 連線。
聯絡您的網際網路服務提供者瞭
解詳情。
12 授權
The terms HDMI and HDMI HighDefinition Multimedia Interface, and the
HDMI Logo are trademarks or
registered trademarks of HDMI
Licensing LLC in the United States and
other countries.
• Spotify 軟件受協力廠商許可約束,可
前往下面的網址瞭解相關資訊:
www.spotify.com/connect/thirdparty-licenses。
• 如需 Spotify Connect 的更多資訊,請
造訪 www.spotify.com/connect
13 開源軟件許可聲
明
Manufactured under license from Dolby
Laboratories. Dolby, Dolby Audio,
Pro Logic, and the double-D symbol are
trademarks of Dolby Laboratories.
如需在本產品中使用的開源軟件的詳細資
訊,請造訪下面的網站 :
http://opensource.samsung.com
For DTS patents, see http://patents.dts.com.
Manufactured under license from DTS
Licensing Limited. DTS, the Symbol, DTS in
combination with the Symbol, and DTS 2.0
Channel are registered trademarks or
trademarks of DTS, Inc. in the United States
and/or other countries. © DTS, Inc. All
Rights Reserved.
HKG - 31
14 有關維修的重要說明
本使用說明書中的圖片和圖解僅供參考,可能與實際的產品外觀有所不同。
15 規格和指南
規格
USB
一般
5V/0.5A
重量
5.0 千克
尺寸
890.0 x 71.0 x 130.5 毫米
工作溫度範圍
+5°C 到 +35°C
(宽 x 高 x 厚)
工作濕度範圍
揚聲器
支援的播放格式
(DTS 2.0 聲音以 DTS 格式播放。)
10 % ~ 75 %
低音炮 x 4,高音揚聲器 x 2,4ohm
LPCM 2ch,Dolby Audio™
(支援 Dolby® Digital),DTS
備註
• Samsung Electronics Co.,Ltd 保留隨時變更規格的權利,恕不另行通知。
• 重量和尺寸為估計值。
• 如需更多有關電源供應和耗電資料,請參閱產品貼附標籤。
(標籤:Soundbar 主設備底部)
HKG - 32
© 2017 Samsung Electronics Co., Ltd. All rights reserved.
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer
care Centre.
Area
Contact Centre 
Web Site
` Asia Pacific
CHINA
400-810-5858
www.samsung.com/cn/support
HONG KONG
3698 4698
www.samsung.com/hk/support (Chinese)
www.samsung.com/hk_en/support (English)
MACAU
0800 333
www.samsung.com/support
SINGAPORE
1800-SAMSUNG(726-7864)
www.samsung.com/sg/support
AUSTRALIA
1300 362 603
www.samsung.com/au/support
NEW ZEALAND
0800 726 786 (All Product)
0800 6 726 786 (Support for Smart Mobile Devices)
www.samsung.com/nz/support
VIETNAM
1800 588 889
www.samsung.com/vn/support
THAILAND
0-2689-3232
1800-29-3232 (Toll free)
MYANMAR
+95-1-2399-888
CAMBODIA
+855-23-993232
1800-20-3232 (Toll free)
LAOS
+856-214-17333
MALAYSIA
1800-88-9999
+603-7713 7420 (Overseas contact)
www.samsung.com/my/support
INDONESIA
021-5699-7777
0800-112-8888 (All Product, Toll Free)
www.samsung.com/id/support
PHILIPPINES
1-800-10-726-7864 [ PLDT Toll Free ]
1-800-8-726-7864 [ Globe Landline and Mobile ]
02-422-2111 [ Standard Landline ]
www.samsung.com/ph/support
TAIWAN
0800-329-999
www.samsung.com/tw/support
JAPAN
0120-363-905
www.galaxymobile.jp/jp/support
INDIA
1800 40 SAMSUNG (1800 40 7267864) (Toll-Free)
NEPAL
16600172667 (Toll Free for NTC Only)
9801572667
BANGLADESH
0961-2300300
0800-0300300 (Toll free)
SRI LANKA
+9411SAMSUNG (+94117267864)
+94117540540
+94115900000
www.samsung.com/th/support
www.samsung.com/in/support
Download PDF