advertisement
▼
Scroll to page 2
of 49
00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page i Operating Instructions CAUTION RISK OF ELECTRIC SHOCK, DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash, with an arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure, that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instruction in the literature accompanying the appliance. WARNING : TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. IMPORTANT SAFEGUARDS i 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page ii Operating Instructions 1. Read all of these instructions. 2. Save these instruction for later use. 3. Unplug this appliance system from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaner. Use a damp cloth for cleaning. 4. Do not use attachments not recommended by the appliance manufacturer, as they may cause hazards. 5. Do not use this appliance near water for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc. 6. Do not place this appliance on an unstable cart, stand, or table. The appliance may fall causing serious injury to a child or adult, and serious damage to the appliance. Use only with a cart or stand recommended by the manufacturer’s instructions, and use a mounting kit approved by the manufacturer. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn. ii 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page iii Operating Instructions 7. Slots and openings in the cabinet on the back or bottom are provided for ventilation, to insure reliable operation of the appliance, and to protect from overheating. These openings should never be blocked by placing the appliance on a bed, sofa, rug or other similar surfaces. This appliance should never be placed near or over a radiator or heat register. This appliance should not be place in a built-in installation such as a bookcase, unless proper ventilation is provided. 8. This appliance should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company. 9. Do not allow anything to rest on the power cord. Do not locate this appliance where the cord will be abused by people walking on it. 10. Do not overload wall outlets and extension cords, as this can result in fire or electric shock. 11. Follow all warnings and instructions marked on the appliance. 12. Do not attempt to service this appliance yourself, as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. iii 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page iv Operating Instructions 13. Unplug this appliance from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the appliance. c. If the appliance does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the appliance to normal operation. d. If the appliance has been exposed to rain or water. e. If the appliance has been dropped or the cabinet has been damaged. f. When the appliance exhibits a distinct change in performance this indicates a need for service. 14. When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. 15. Upon completion of any service or repairs to the appliance, ask the service technician to perform routine safety checks to determine that the appliance is in safe operating condition. iv 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 1 Operating Instructions Contents 1. Introduction ..................................................... 2 2. Features ........................................................... 3 3. Installation ...................................................... 5 Precautions in Installation and Use ...................... 5 Connecting Auto Iris Lens Connector ................. 6 Mounting lens ......................................................... 7 Setting Lens Selection Switch ............................... 8 Adjusting Back Focus ............................................ 9 Connecting Cable ................................................. 11 4. Name and Functions of Parts...................... 14 Name and Functions of Camera Parts ............... 14 Camera Setup ........................................................ 19 5. Product Specifications................................. 39 1 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 2 Operating Instructions 1. Overview Adopting the latest Super-HAD CCD (Charge Coupled Device), the CCTV COLOR CAMERA SCC-833(P)/835(P)/803P/805P are monitoring camera which can provide the best monitoring function when connected to the CCTV system equipment by realizing SWDR (Super Wide Dynamic Range) and low illumination function. Broadcasting System • SCC-833/835 : NTSC • SCC-833P/835P/803P/805P : PAL Number of CCD Pixel • SCC-833 : 1/3" NTSC 410K (High resolution type) • SCC-835 : 1/2" NTSC 410K (High resolution type) • SCC-833P/803P : 1/3" PAL 470K (High resolution type) • SCC-835P/805P : 1/2" PAL 470K (High resolution type) Power Source • SCC-833(P)/835(P): AC 24V, DC12V • SCC-803P/805P : AC 220V ~ 240V 2 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 3 Operating Instructions 2. Features High Sensitivity Adopting the Super-HAD CCD that has the latest built-in microchip lens, the high sensitivity is realized. SWDR Function With built-in SWDR (Super Wide Dynamic Range) function using Dual Shutter method, distinction of light and darkness is clear in areas where the illumination levels differ greatly or the light source is right behind the subject. Low Illumination Function It is possible to shoot in the worst situation where there is no light by adopting a low illumination function based on the Digital Signal Technology. Excellent Back Light Compensation Even when an intense light source or sunlight is in the back of your subject, a clear image can be provided due to the ideal combination of the excellent performance of the high light compression (Knee Compensation) function and the BLC (Back Light Compensation) function. 3 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 4 Operating Instructions Digital Line-lock The control and reliability has been enhanced due to the Full Digital Line Lock, which allows users to adjust the Line Sync Phase. Resolution High resolution is realized due to the Full Digital Image Processing utilizing the best Digital Signal Technology. Output Signal Selection Video output signal reverse function and frame setting (horizontal, vertical) function are incorporated. Remote Control The operation of the camera can be remotely controlled due to the built-in remote control protocol of the RS-485 Standards. * Remote control using PC requires additional RS485/232C Interface Jig. 4 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 5 Operating Instructions 3. Installation Precautions in Installation and Use 1) Do not attempt to disassemble the camera yourself. 2) Be cautious in handling the camera. Avoid striking or shaking the camera. Make sure to avoid damage on the camera caused by improper storage or operation. 3) Do not expose the camera to rain or moisture. Do not operate the camera on a wet place. 4) Do not use strong or abrasive detergents when cleaning the camera body. Use a dry cloth to clean the camera. 5) Keep the camera at a cool place away from the direct sunlight. Leaving the camera under the direct sunlight may result in a malfunction of the unit. 5 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 6 Operating Instructions Connecting Auto Iris Lens Connector Prepare the Auto Iris Lens Connector, which is supplied along with the camera. Rib Pin3 Pin1 Pin4 Pin2 Connect the cable of the control cable, whose covering is stripped, to the Auto Iris Lens Connector as shown below. Pin Number DC Control Type Video Control Type 1 Damp (–) Power (+9V) 2 Damp (+) Not used 3 Drive (+) Video signal 4 Drive (–) GND 6 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 7 Operating Instructions Mounting the Lens Loosen a screw fixing the Flange Back Adjustment Ring by turning it counterclockwise and turn the Adjustment Ring to the “C” direction (counterclockwise) until it stops. Failure to do so may result in a damage caused by a bump of the lens against the image sensor part in the camera when mounting the lens. C direction VID EO DC LEN S Auto Iris Control Cable 7 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 8 Operating Instructions Setting Lens Selection Switch When lens mounting is completed, set the Lens Selection Switch on the lateral side of the camera according to the type of lens mounted. When the mounted lens is an Auto Iris Lens of DC control type, set the Lens Selection Switch to “DC”. When the mounted lens is an Auto Iris Lens of video control type, set the Lens Selection Switch to “VIDEO”. VIDEO AI LENS VIDEO AI LENS DC DC EO VID S LEN DC 8 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 9 Operating Instructions Adjusting Back Focus Although the Back Focus of the camera has been adjusted in the factory before its shipment, the focus may not be accurate for a certain type of lens. In this case, follow the procedures below to adjust the back focus. First, following is how to adjust the Back Focus of the Fixed Focus Lens. 1) Lightly loosen up the screw fixing the Back Focus Adjustment Ring using a screwdriver. 2) Image a vivid subject (with check patterns) at a distance of more than 10m away and turn the Focus Ring to the infinity ( ∞ ) position. 3) Adjust the Back Focus Adjustment Ring to obtain the clearest image of the subject. 4) Fasten the screw fixing the Back Focus Adjustment Ring. O VIDE LENS DC 9 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 10 Operating Instructions The following describes how to adjust the Back Focus when using a Zoom Lens. 1) Lightly loosen up the screw fixing the Back Focus Adjustment Ring using a screwdriver. 2) Image a vivid subject (with check patterns) at a distance of 3 to 5 meters away and adjust the zoom of the lens to TELE as far as it goes. Then adjust the Focus Ring of the lens to obtain the clearest image of the subject. 3) Adjust the zoom of the lens to WIDE as far as it goes. Then turn the Back Focus Ring of the camera to obtain the clearest image of the subject. 4) Repeat the number 2) and 3) steps two to three times to exactly coincide the zoom focus from TELE with that from WIDE. 5) Fasten the screw fixing the Back Focus Adjustment Ring. O VIDE LENS DC Note: Turning the Back Focus Adjustment Ring to the “C” direction beyond the adjustable range makes a sound at the limit. 10 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 11 Operating Instructions Connecting Cable After mounting the lens and setting the Lens Selection switch, connect the prepared cable to each terminal of the camera. 1) First, connect one end of the BNC cable to the Video Output Terminal (VIDEO OUT) of the camera. 2) Then connect the other end of the BNC cable to the Video Input Terminal of the camera. VIDEO LINE AUDIO LINE Video A Video B Video C IN IN IN OUT OUT A B C OUT IN OUT Video In Terminal EO VID BNC cable LENS DC Video Out Terminal (VIDEO OUT) 11 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 12 Operating Instructions 220 110 3) Then connect the power adapter. As for SCC-833/P, 835/P, connect one end of two lines of the power adapter using a screwdriver to the Power In Terminal of the camera as shown below. * Connect to the AC 24V or DC 12V power source, without the distinction of the polarity. EO VID S LEN DC AC24V DC12V 12 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 13 Operating Instructions 4) Connect the power input cord to the AC 230V power source. (SCC-803P/805P) EO VID DC 13 S LEN 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 14 Operating Instructions 4. Names and Functions of Parts • Side View Auto Iris Lens Connector Groove for Mount Adapter Flange-Back Adjustment Ring Camera lens VID EO DC LEN S ALC Lens Selection Switch Auto Iris Lens Control Cable Groove for Mount Adapter Use this groove for fixing the mount adapter to be connected to the bracket with screws when mounting the camera on the bracket. Auto Iris Lens (Option) Lens to be mounted on the camera. 14 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 15 Operating Instructions Note: When the surface of the camera lens is contaminated, wipe the surface gently with a tissue for lens or a cotton cloth applied with ethanol. Auto Iris Lens Connector Used for supplying power, which is required to control the iris of the lens, as well as control signal, video signal, or DC signal to the Auto Iris Control Lens Auto Iris Lens Control Cable Used for transmitting the control signals to the camera to control the iris of the lens. Flange-Back Adjustment Ring Used for adjusting the Back Focus. ALC Lens Selection Switch Used when selecting the type of Auto Iris Lens to use. DC: Select this switch to DC when Auto Iris Lens requiring DC control signal is mounted. VIDEO: Select this switch to VIDEO when Auto Iris Lens requiring VIDEO control signal is mounted. 15 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 16 Operating Instructions • Rear Panel SCC-803P/805P 5 6 AC 220-240V PWR 1 2 REMOTE VIDEO OUT ALARM OUT GND 4 3 SCC-833(P), 835(P) 5 4 ALARM OUT GND PWR 1 2 REMOTE AC 24V DC 12V 6 VIDEO OUT 3 16 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 17 Operating Instructions 1) Power Indication LED While the power is properly supplied to the camera, the LED is turned on. 2) VIDEO Output Terminal This is a terminal to be connected to the Input Terminal of the monitor and others. Through this terminal, video signal is output. 3) Remote Input Terminal (RS485 control) This is a connection terminal used to adjust the camera in the factory, and it can be controlled remotely using RS485 Half Duplex. REMOTE 1 2 3 4 1 2 3 4 A(TXD) B(RXD) +5V GND 4) Alarm Signal Output Alarm signal is generated when Motion Detection of camera occurs. ALARM Signal GND 17 Open/Gnd GND 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 18 Operating Instructions 5) Camera Control Switch 1 2 4 3 5 1. Up Switch Used when moving the cursor upward. 2. Left Direction Switch Used when moving the cursor to the left direction, changing modes or adjusting levels. 3. Down Switch Used when moving the cursor downward. 4. Right Direction Switch Used when moving the cursor to the right direction, changing modes or adjusting levels. 5. Setting Switch Used when entering the sub menu or setting changed menus (save, quit, or preset). 6) Power Connection Terminal Terminal to be connected to the power (adapter) cable. SCC-803P/805P: Connect it to AC 230V (power cable) SCC-833(P)/835(P): Connect it to AC 24V/ DC 12V (power adapter) 18 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 19 Operating Instructions Camera Setup Setup menu is configured as follows: CAMERA ID OFF/ON--- ON--Write an ID/Select the position SENSE UP OFF/FIX X2~32/ AUTO X2~32 ALC--WDR OFF/AUTO/ON--(Adjust Level) SHUTTER OFF~100K Adjust Iris ALC/ELC ALC---/ELC--- ELC--Adjust LEVEL S E T U P BLC OFF/ON--- ON--AREA POSITION--(Adjust Position) PRESET OFF/ON M E N U WHITE BAL. ATW/AWC/MANU--- MANU--PRESET 3200K/ PRESET 5600K/ PRESET OFF(USER)-(Adjust R/B) SYNC INT/LINE--- LINE--Adjust V-PHASE AGC ON/OFF MANU--Set RS 485ADDR Adjust H-DTL Adjust V-DTL Select Posi/Nega Select Left/Right Select Up/Down VIDEO CON. FIX/MANU--MOTION DET OFF/ON--EXIT QUIT/SAVE/PRESET 19 ON--AREA SET--(Adjust Position) PRESET OFF/ON Adjust LEVEL 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 20 Operating Instructions Operation of the Setup Menu Press the Setup Switch for two to three seconds to switch from the general mode to the Setup Mode. Then the Setup Menu pops up on the screen. Setup menu shown on the monitor is as follows: (SET UP) CAMERA ID SENSE UP ALC/ELC BLC AGC WHITE BAL SYNC VIDEO CON MOTION DET EXIT OFF OFF ALC--OFF ON ATW INT FIX OFF QUIT? Setup Menu (SET UP) Flickering CAMERA ID SENSE UP ALC/ELC BLC AGC WHITE BAL SYNC VIDEO CON MOTION DET EXIT OFF OFF ALC--OFF ON ATW INT FIX OFF QUIT? 20 Indicates that SUB-MENU exists 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 21 Operating Instructions 1) Indication of the Main Menu Press the Setup Switch for about two to three seconds, then the Setup Menu (Main Menu) will be shown as seen in the diagram below. 2) Indication of the Sub Menu “---” mark next to the item indicates that there is a sub-menu under the main. Move the cursor to the item with “---” and press the Setup Switch. Then the sub menu will pop up. Select the Sub Menu to see the detailed menu as follows: (AWB/MANU) Implies that there are adjustment items (RED/BLUE). PRESET RED (00) BLUE (00) RET OFF(USER)----- ------- ---- 21 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 22 Operating Instructions Camera Setup 1) Camera Setup Move the cursor to “Camera ID” and select On--(Camera ID Indication) using the right/ left direction switch and press the Setup Switch. (SET UP) CAMERA ID SENSE UP ALC/ELC BLC AGC WHITE BAL SYNC VIDEO CON MOTION DET EXIT ON--OFF ALC--OFF ON ATW INT FIX OFF QUIT? The next screen shows the Camera ID Menu as follows: The character cursor is placed on “A” and the code writing cursor flickers on the place where the code should be written. (CAMERA ID) A B C D M N O P Y Z 0 1 . ; : E Q 2 ? F R 3 + G S 4 - H T 5 * I U 6 ( J V 7 ) K L W X 8 9 / SP➝ ➝ SP LOCATION RET ............ 22 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 23 Operating Instructions A total of 12 characters can be entered. Move the character cursor to the position you want using the up/down/right/left direction switch and then press the Setup Switch. Repeat this until you have the text you want. When you want to enter a space between letters, move the character cursor to “SP Æ ¨ SP” and press the Setup Switch. When all the characters you want are entered, move the cursor to “LOCATION” and press the Setup Switch to have the menu that allows you to change the location of camera ID. The location of the camera ID can be changed and fixed using the up/down/right/left direction switch. Press the Setup Switch for 2 to 3 seconds after the location is selected to return to the previous Sub Menu screen. Place the selection cursor at “RET” on Sub Menu screen and press the Setup Switch to return to the Setup Menu screen. Set “ON---” for the selected camera ID to be displayed on the screen. 2) Sense Up Mode (Low Illumination Mode) First, move the cursor to the “Sense Up” and select the scale mode, which is suitable for the camera environment using the right/left direction switch. 23 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 24 Operating Instructions (SET UP) CAMERA ID SENSE UP ALC/ELC BLC AGC WHITE BAL SYNC VIDEO CON MOTION DET EXIT OFF AUTO X12 ALC--OFF ON ATW INT FIX OFF QUIT? Functions are as follows: First, sense up mode is not operated when it is “Off”. Off means 1/60 for NTSC and 1/50 for PAL. In Fix Mode, designated scale mode is not operated in any condition. In Auto Mode, scale mode is operated automatically within the range of the scale set according to the brightness of the screen. * When “ALC/ELC MODE” is set as “ALC---” (when WDR is off) OFF ➝ AUTO X2 ➝ AUTO X4 ➝ AUTO X6 ➝ AUTO X8 ➝ AUTO X12 ➝ AUTO X16 ➝ AUTO X24 ➝ AUTO X32 ➝ OFF ➝ FIX X2 ➝ FIX X4 ➝ FIX X6 ➝ FIX X8 ➝ FIX X12 ➝ FIX X16 ➝ FIX X24 ➝ FIX X32 * When “ALC/ELC MODE” is set as “ALC---” (when WDR is AUTO) OFF ➝ AUTO X2 ➝ AUTO X4 ➝ AUTO X6 ➝ AUTO X8 ➝ AUTO X12 ➝ AUTO X16 ➝ AUTO X24 ➝ AUTO X32 When the WDR on the ALC MENU is set “ON” (Sense Up Function cannot be operated at the same time), Data is not switched to FIX. Only when WDR is set “OFF” it can be switched to “FIX” and in this case WDR on the ALC LENS MENU is indicated as “---” and WDR is not to be set anew. * When “ALC/ELC MODE” is set as “ELC---” OFF ➝ AUTO X2 ➝ AUTO X4 ➝ AUTO X6 ➝ AUTO X8 ➝ AUTO X12 ➝ AUTO X16 ➝ AUTO X24 ➝ AUTO X32 24 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 25 Operating Instructions 3) ALC/ELC Mode Move the cursor to “ALC/ELC” and select “ALC---/ELC---” using the right/left direction switch. (SET UP) CAMERA ID SENSE UP ALC/ELC BLC AGC WHITE BAL SYNC VIDEO CON MOTION DET EXIT OFF OFF ALC--OFF ON ATW INT FIX OFF QUIT? When “ALC---” is selected, ALC Menu details are available. When “ELC---” is selected, ELC Menu details are available. * When the Sense up Mode is fixed, ELC, Shutter WDR mode is displayed as “---” and setting is not to be changed. (1) ALC Menu Setting Move the cursor to “WDR” and select “OFF/ON--” using the right/left direction switch. (However, when the Sense up Mode is fixed, “---” will be displayed and setting is not to be changed.) 25 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 26 Operating Instructions (ALC) WDR LEVEL (0) SHUTTER IRIS (0) ON----- ---------- ---- RET (ALC) WDR OFF SHUTTER (0) IRIS OFF ---- ---- RET When “OFF” is set, WDR function is not available and level is not indicated. When “ON--” is set, level is indicated. Move the cursor to the Level item and use the right/left direction switch to adjust WDR level. (When WDR is ON--, Shutter is indicated as “---” and its setting is not to be changed.) When Auto is set, WDR function is automatically made on or off based on the counter light status. 26 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 27 Operating Instructions – Setting the Shutter Speed First, move the cursor to the “SHUTTER” and select the Shutter Speed (16phases “OFF ~ 100K”) using the right/left direction switch. (ALC) WDR OFF SHUTTER (0) IRIS OFF ---- ---- RET Shutter speeds are as follows: Off → 100 → 250 → 500 → 750 → 1000 → 1500 → 2000 → 3000 → 5000 → 7000 → 10K → 20K → 30K → 50K → 100K (NTSC) Off → 120 → 250 → 500 → 750 → 1000 → 1500 → 2000 → 3000 → 5000 → 7000 → 10K → 20K → 30K → 50K → 100K (PAL) 27 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 28 Operating Instructions – IRIS Setting Move the cursor to “IRIS” and adjust the relevant data using right/left direction switch. Iris value of the DC lens is determined by the selected data. (For Video lens, the iris value is determined by the data value only when the BLC motion is set “ON”.) (2) Setting ELC Menu First, select ELC on ALC/ELC Menu and select the LEVEL. Target level can be adjusted using the right/left direction switch. (ELC menu is used only for non AI Lens.) 4) BLC Mode Move the cursor to “BLC” and select “OFF/ ON---” using the right/left direction switch. When “OFF” is set, BLC is not operated. When “ON---” is set, BLC is operable. * When WDR is ON---, BLC is indicated as “---” and its setting is not to be changed. (SET UP) CAMERA ID SENSE UP ALC/ELC BLC AGC WHITE BAL SYNC VIDEO CON MOTION DET EXIT OFF OFF ALC--ON--ON ATW INT FIX OFF QUIT? 28 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 29 Operating Instructions BLC Range Setting Select the BLC Menu and move the cursor to “AREA SET---”. Then press the Setup Switch to have the BLC Area displayed. Select the Area Location using the right/left direction switch. (BLC) AREA SET--PRESET OFF RET Press the Setup Switch on the designated spot to make the BLC setting ON. Press it once more to turn it into OFF. (*Location can be adjusted only when the PRESET is OFF. When it is ON, it is fixed as it is set when shipment is made.) Press the Setup Switch for longer than 2 seconds after the location setting is completed to return to the previous Menu (BLC Mode). BLC is operated by the data for the areas selected when BLC is 29 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 30 Operating Instructions 5) AGC MODE Move the cursor to “AGC” and select “ON/OFF” using the right/left direction switch. (SET UP) CAMERA ID SENSE UP ALC/ELC BLC AGC WHITE BAL SYNC VIDEO CON MOTION DET EXIT OFF OFF ALC--OFF ON ATW INT FIX OFF QUIT? When it is set “OFF”, the camera set the AGC gain DATA to “0”. When it is set “ON”, AGC is operated. 6) WHITE BAL MODE Move the cursor to “WHITE BAL” and select “ATW/AWC/MANU---” using the right/left direction switch. (SET UP) CAMERA ID SENSE UP ALC/ELC BLC AGC WHITE BAL SYNC VIDEO CON MOTION DET EXIT OFF OFF ALC--OFF ON MANU--INT FIX OFF QUIT? 30 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 31 Operating Instructions - When “ATW” selected, Auto White Balance Control is on. - When “AWC” is selected, White Balance Control memorized previously utilizing AWC is on. When setting new AWC condition, press the Setup Switch while AWC is selected. Then AWC becomes flickering and White Balance Control is operated to memorize the data. When the setting is completed, the flickering stops. * While “ATW” always calls White Balance, “AWC” calls White Balance only once when the user presses the Setup Switch. - When “MANU---” is set, White Balance is called in the condition, which is determined on AWB/MANU MENU. (1) Setting AWB/MANU MENU Move the cursor to “PRESET” and select the “PRESET 3200K/PRESET 5600K/PRESET OFF (USER)--” using right/left direction switch. (AWB/MANU) PRESET 3200K RET 31 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 32 Operating Instructions - When “PRESET 3200K” is set, each Red and Blue comes out in 3200°K. - When “PRESET 5600K” is set, each RED and Blue comes out in 5600°K. (AWB/MANU) PRESET RED (0) BLUE (0) RET OFF(USER)----- ------- ---- - When “PRESET OFF (USER)--” is set, each Read and Blue Gain can be adjusted by the user. (AWB/MANU) PRESET RED (0) BLUE (0) RET OFF(USER)----- ------- ---- 32 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 33 Operating Instructions 7) SYNC MODE Move the cursor to “SYNC” and select the “Power Sync (LINE---)/Internal Sync (INT)” using right/left direction switch. (SET UP) CAMERA ID SENSE UP ALC/ELC BLC AGC WHITE BAL SYNC VIDEO CON MOTION DET EXIT OFF OFF ALC--OFF ON ATW INT FIX OFF QUIT? If the camera is set to INT (Internal Sync) mode when monitoring in the Auto Switching mode with more than one camera connected to a sequential switcher, etc, the jump of the screen will occur each time of screen switching. To switch the screen gently without a jump, set the camera to “L.L” and adjust the Vertical Sync Phase. * However, L.L function can be used only when using AC power. This setting is prohibited when DC power is used. When DC power is used, only INT is available. 33 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 34 Operating Instructions - Move the selection cursor of the LINE LOCK MENU to “V-PHASE” and adjust the line lock of the camera by using right/left direction switch. (LINE LOCK) V-PHASE (00) RET ---- ---- 8) VIDEO CON MODE Move the cursor to “VIDEO CON” and select the “FIX/MANU---” using right/left direction switch. When “FIX” is selected, the conditions at the time of shipment are set. When “MANU---” is selected, H-DTL, V-DTL, posi/nega of the video signal can be changed by the user on VIDEO CONTROL SUB MENU. (SET UP) CAMERA ID SENSE UP ALC/ELC BLC AGC WHITE BAL SYNC VIDEO CON MOTION DET EXIT OFF OFF ALC--OFF ON ATW INT MANU--OFF QUIT? 34 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 35 Operating Instructions Setting the VIDEO CONTROL MENU - Setting RS485 ADDR (refer to the diagram below) Move the cursor to “RS 485 ADDR” and select the “0~255” using right/left direction switch. (0~255: the number of cameras that can be used). When a multiple number of cameras is used, Address to control each camera should be set using RS485 communications. - Adjusting H-DTL (refer to the diagram on page 36) Move the cursor to “H-DTL” (horizontal edge adjustment) and change the value using the right/left direction switch. The value can become + or – starting from 0 using the right/left direction switch. - Adjusting V-DTL (refer to the diagram on page 36) Move the cursor to “V-DTL” (vertical edge adjustment) and change the value using the right/ left direction switch. The value can become + or – starting from “0” using the right/left direction switch. - Setting POSI/NEGA (refer to the diagram on page 36) Move the cursor to “POSI/NEGA” and select “POSI/NEGA” using the right/left direction switch. When “POSI” is selected, video signals (Y, Chroma signal) are generated in a normal way. When “NEGA” is selected, video signals (Y, Chroma signal) are generated in the opposite way. (Often used when imaging film.) Note: When using Video Al lens, normal operation is not made even when “NEGA” is set. 35 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 36 Operating Instructions – Setting H-REV (refer to the diagram below) Move the cursor to “H-REV” and select “ON/ OFF” using the right/left selection switch. When “OFF” is selected, video signal is output normally. When “ON” is selected, video signal is output in right/left reverse. – Setting V-REV (refer to the diagram below) Move the cursor to “V-REV” and select “ON/ OFF” using the right/left selection switch. When “OFF” is selected, video signal is output normally. When “ON” is selected, video signal is output in up/down reverse. (VIDEO CONTROL) RS485 ADDR H-DTL V-DTL POSI/NEGA H-REV V-REV RET 0 ---- ------- ---POSI OFF OFF 9) MOTION DET MODE Move the cursor to “MOTION DET” and select “ON---/OFF” using the right/left selection switch. When “OFF” is selected, motion detection is not made. When “ON---” is selected, range and level for the motion detection can be set. When the MOTION is detected, ALARM OUT terminal becomes Gnd and the ALARM is lifted automatically about 30 seconds later. (GND/OPEN) 36 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 37 Operating Instructions (SET UP) CAMERA ID SENSE UP ALC/ELC BLC AGC WHITE BAL SYNC VIDEO CON MOTION DET EXIT OFF OFF ALC--OFF ON ATW INT FIX ON--QUIT? The setting of the MOTION DET MENU is as follows: Move the MOTION DETECT range selection cursor to “AREA SET---” and press the Setup Switch to see the MOTION AREA. Select the AREA location using the right/left direction switch and press the Setup Switch. Then the range for MOTION detection is turned off. Press it once more to turn it on. (However, location can be set only when the PRESET is OFF. When it is ON, the conditions are fixed to as they are right before the shipment.) When the location selection is completed, press the Setup Switch for longer than 2 seconds to return to the previous MOTION DET MENU. 37 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 38 Operating Instructions – Setting the LEVEL Move the cursor to “LEVEL” and choose MOTION DETECTION LEVEL within the selected range using the right/left selection switch. (MOTION DETECT) AREA SET--PRESET LEVEL (0) OFF ---- ---- RET 10) EXIT MODE Move the cursor to “EXIT” and select “QUIT?/SAVE?/PRESET” using the right/left direction switch. - Set “QUIT?” and press the Setup Switch to return to the original data disregarding the data that the user modified in MENU. Set the “SAVE?” and press the Setup Switch to save the values that the user changed in MENU. - Set the “PRESET” and press the Setup Switch to return to the initial data (when shipment is made) disregarding the data that user changed in MENU. 38 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 39 Operating Instructions 5. Product Specifications SCC-833 / 835 Item Details Product Type Monitoring Camera Broadcasting System NTSC STANDARD SYSTEM CCD 833: 1/3 " IT type S-HAD CCD 835: 1/2 " IT type S-HAD CCD No. of Pixel 768 (H) ✕ 494 (V) Scanning Type 525 Line, 2:1 Interlace Frequency INT: 15,734 Hz (H), 59.94 Hz (V) LL: 15,757 Hz(H), 60 Hz (V) Sync Type INT/LINE LOCK (when AC power source is used) Resolution 480 TV LINES S/N Ratio 50dB or more (AGC OFF) Min. Object Illumination 833: 0.06 Lux 835: 0.03 Lux Dynamic Range 40dB or more (32 times) Sense Up Up to 32 times (OFF/FIX X2 ~ FIX X32/AUTO X2 ~ AUTO X32) BLC Back light compensation (location setting possible) ELC Electronic Iris function 39 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 40 Operating Instructions Item Details Shutter Setting OFF ~ 1/100K seconds (16 steps) Motion Det. Motion detection (Alarm Out) ID Setting Up to 12 characters (location setting) Color Temperature Setting ATW/AWC/MANUAL MODE (3200°K, 5600°K, R/B Gain adjustment) Signal Output COMPOSITE VIDEO OUT: 1.0 Vp-p 75 ohms/BNC Power Source AC 24V ± 10% (60Hz ± 0.3Hz) DC12V + 10% - 5% Power Consumption About 4W Operating Environment (Temperature) -10°C ~ +50°C Operating Environment (Humidity) ~ 90% Size 65 (W) ✕ 52(H) ✕ 133 (L)mm (BNC included) Weight 450g Altitude 3,000M or less 40 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 41 Operating Instructions SCC-833P/835P/803P/805P Item Details Product Type Monitoring Camera Broadcasting System PAL STANDARD SYSTEM CCD 833P/803P: 1/3" IT type S-HAD CCD 835P/805P: 1/2" IT type S-HAD CCD No. of Pixel 752 (H) ✕ 582 (V) Scanning Type 625 Line, 2:1 Interlace Frequency INT: 15,625 Hz (H), 50 Hz (V) LL: 15,625 Hz(H), 50 Hz (V) Sync Type INT/LINE LOCK (when AC power source is used) Resolution 480 TV LINES S/N Ratio 50dB or more (AGC OFF) Min. Object Illumination 833P/803P: 0.06 Lux 835P/805P: 0.03 Lux Dynamic Range 42dB or more (40 times) Sense Up Up to 32 times (OFF/FIX X2 ~ FIX X32/AUTO X2 ~ AUTO X32) BLC Back light compensation (location setting possible) ELC Electronic Iris function 41 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 42 Operating Instructions Item Details Shutter Setting OFF ~ 1/100K seconds (16 steps) Motion Det. Motion detection (Alarm Out) ID Setting Up to 12 characters (location setting) Color Temperature Setting ATW/AWC/MANUAL MODE (3200°K, 5600°K, R/B Gain adjustment) Signal Output COMPOSITE VIDEO OUT: 1.0 Vp-p 75 ohms/BNC Power Source 833P/835P: AC 24V ± 10% (50Hz ± 0.3Hz), DC12V + 10% - 5% 803P/805P: AC220 ~ AC240V Power Consumption 833P/835P: about 4W 803P/805P: about 4.8W Operating Environment (Temperature) -10°C ~ +50°C Operating Environment (Humidity) ~ 90% Size 65 (W) ✕ 52(H) ✕ 133 (L)mm (BNC included) Weight 833P/835P: 450g 803P/805P: 550g Altitude 3,000M or less 42 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 43 Operating Instructions RS-485 Remote Control This is RS-485 Protocol about keys of SCC-833. Target Address is able to change in sub menu of VIDEO CONTROL, SCC-833. Default value of target address is 0. ➔ ➔ (LEFT) (RIGHT) ➔ Enter ➔ The below value is hexadecimal. (UP) (DOWN) BYTE1 A0 H BYTE2 Sender Address BYTE3 Target Address BYTE4 03 H BYTE5 18 H 05 H 07 H 03 H 09 H BYTE6 FF H BYTE7 FF H BYTE8 FF H BYTE9 CheckSum Low Byte of (FFFF H(Summation of byte2~Byte8)) Port Setting • Baud Rate : 38400 bps • Data Bits : 8 bits • Stop Bit : 1 bit • Parity Bit : None 43 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 44 Part No.: AB68-00107A (Rev. 01) Printed in Korea 00107A SCC-833P/855P - gb 6/28/01 5:30 PM Page 45 Super WDR & Low Light Digital Color Camera SCC-833(P) SCC-835(P) SCC-803P/805P Operating Instructions
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project