Samsung | AS12CM1N/XAZ | Samsung AS12CM1/XSH User Manual

USER’S MANUAL
Indoor Unit
Outdoor Unit
AS09CM1N
AS09CM2N
AS12CM1N
AS12CM2N
AS18CM1N
AS18CM2N
AS24CM1N
AS24CM2N
AS09CM1X
AS09CM2X
AS12CM1X
AS12CM2X
AS18CM1X
AS18CM2X
AS24CM1X
AS24CM2X
Split-type Air Conditioner
(Cooling)
E DB98-21718A(2)
Register your product at www.samsung.com/global/register
Safety Precautions
You should take the following safety precautions when using your air conditioner.
WARNING
DURING
OPERATION
• If you don’t follow the safety precautions, you may get the risk of an electric
shock, injury or death.
•The manufacturer or qualified service personnel must install this air conditioner.
• Turn off the electric power before repairing, installing or cleaning.
◆ Do not repair the air conditioner at your discretion.
It is recommended to contact a service center directly.
◆ Never spill any kind of liquid on the air conditioner.
If this happens, turn off the air conditioner and contact an authorized
service center.
◆ Do not insert anything between the airflow blades to prevent damage of
the inner fan and consequent injury. Keep children away from the air
conditioner.
◆ Do not place any obstacles in front of the air conditioner.
◆ Do not spray any kind of liquid into the indoor unit. If this happens,
turn off the air conditioner and contact a service center.
◆ Make sure that the air conditioner is well ventilated at all times:
Do not place a cloth or other materials over it.
◆ Remove the batteries if you don’t use the remote control for a long
time. (If applicable)
◆ Use the remote control within 7 meters from the indoor unit. (If applicable)
DISPOSING OF THE UNIT
◆ Before throwing out the air conditioner, remove the batteries from the
remote control.
◆ When you dispose of the air conditioner, consult your dealer. If pipes
are removed incorrectly, refrigerant may blow out and cause air
pollution. When it contacts with your skin, it can cause skin injury.
◆ The package of the air conditioner should be recycled or disposed of
properly for environmental reasons.
OTHERS
◆ Never store or load the air conditioner upside down or sideways to
prevent the damage to the compressor.
◆ Young children or infirm persons should be always supervised when
they use the air conditioner.
◆ Max current is measured according to IEC standard for safety.
◆ Current is measured according to ISO standard for energy efficiency.
E-2
Contents
◆ PREPARATION
■ Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
■ Name of Each Part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
■ Remote Control-Buttons and Display . . . . . . . . . . . . . . . . . . . . . .
■ Inserting the Remote Control Batteries . . . . . . . . . . . . . . . . . . . . .
■ Getting Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
4
6
7
8
◆ OPERATION
■ Selecting the Auto Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
■ Selecting the Cool Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
■ Selecting the Dry Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
■ Selecting the Fan Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
■ Selecting the Turbo Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
■ Selecting the Energy Saving Function . . . . . . . . . . . . . . . . . . . . .
■ Selecting the Auto Cleaning Function . . . . . . . . . . . . . . . . . . . . . .
■ Selecting the Sound On / Off Function . . . . . . . . . . . . . . . . . . . . . .
■ Selecting the Anions Function . . . . . . . . . . . . . . . . . . . . . . . . . . . .
■ Adjusting the Airflow Direction Vertically . . . . . . . . . . . . . . . . . . . .
■ Adjusting the Airflow Direction Horizontally . . . . . . . . . . . . . . . . . .
■ Setting the On Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
■ Setting the Off Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
■ Setting the Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9
10
11
12
13
14
15
16
17
18
19
20
21
22
◆ RECOMMENDATIONS FOR USE
■ Operating Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . .
■ Temperature and Humidity Ranges . . . . . . . . . . . . . . . . . . . . . . . .
■ Operating Your Air Conditioner Without the Remote Control . . . . .
■ Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
■ Cleaning Your Air Conditioner . . . . . . . . . . . . . . . . . . . . . . . . . . . .
■ Cleaning Anti-Allergy and Deodorizing Filter (Option) . . . . . . . . . .
23
24
25
26
27
27
◆ TECHNICAL SPECIFICATIONS
E-3
Name of Each Part
The design and shape can be changed according to the model.
Indoor Unit
Air Inlet
Room Temperature sensor
Power(On/Off) button
Air filter
(under the grille)
Airflow blades
(outlet)
Set temperature &
room temperature
Operation indicator
(Auto-Cool, Cool, Dry, Fan : Blue)
Turbo function indicator
(Blue)
Timer indicator
(Orange)
Auto cleaning indicator
(Blue)
Energy saving indicator
(Blue)
Anions indicator
(Blue)
Fan speed indicator
(Blue)
Remote control sensor
Note
◆ In the Auto mode, 2 fan indicators increase and decrease continuously
and turn round.
◆ In the modes except the Auto mode, the fan speed indicator increases
and decreases continuously and turn round each time you press the
button. If you set the Turbo function, the fan speed indicator turns
round with the maximum setting and speed.
◆ If you want to turn on/off the Display during operation,
press the
button on the remote control.
◆ The room temperature sensor senses air temperature around the
sensor, and shows the temperature on the display.
E-4
Outdoor Unit
AS09CM1(2)X
AS12CM1(2)X
Air Inlet(Rear)
Air Outlet
Connection Valve
(inside)
Outdoor Unit
AS18CM1(2)X
AS24CM1(2)X
Air Inlet(Rear)
Air Outlet
Connection Valve
E-5
Remote Control - Buttons and Display
Operating mode
Remote control
transmission indicator
(
AUTO,
DRY,
COOL,
FAN)
Sound On /Off indicator
Battery life indicator
Fan speed indicator
Anions indicator
Sleep mode indicator
On Timer indicator
Turbo function indicator
Temperature setting
Air flow direction
Off Timer indicator
Energy saving indicator
Power (On/Off) button
Mode selection button
(AUTO, COOL, DRY, FAN)
Fan speed adjustment button
Turbo button
Energy saving button
Temperature adjustment
buttons
Digital
On/Off button
Swing button
Sound On/Off button
Auto Cleaning button
On Timer button
Timer Set/Cancel button
Off Timer button
Sleep button
Anions button
E-6
Inserting the Remote Control Batteries
You must insert or replace the remote control batteries when :
◆ You purchase the air conditioner
◆ The remote control does not work correctly
Note
◆
◆
◆
◆
Use two AAA, LR03 1.5V batteries.
Do not use old batteries or different kinds of batteries together.
Batteries may be completely discharged after 12 months, even
if they have not actually been used.
1
Remove the battery cover in the rear of the remote control by pushing
it with your thumb.
2
Insert two batteries, respecting the polarities as indicated by
the + and - symbols.
3
Close the cover by sliding it back in its place.
E-7
Getting Start
The User’s Manual provides you with valuable information about your air conditioner.
Please read this manual carefully before using the air conditioner.
It will help you take full advantage of the unit's features.
You have already seen the basic description of the unit on pages from 4 to 6.
Starting with the next page, you will find a series of step - by - step procedures
for each function available.
The illustrations in the step-by-step procedures use three different symbols :
PRESS
E-8
PUSH
HOLD DOWN
Selecting the Auto Mode
You can select the Auto mode if you want to cool your room automatically.
You can adjust the temperature in this mode.
1
If necessary, press the
Result:
2 Press the
(On/ Off) button.
◆ The operation indicator on the indoor unit lights up.
◆ The air conditioner starts up in the mode you selected last.
◆ The indoor unit beeps.
button on the remote control until
is displayed.
Result:
◆ The indoor unit beeps each time you press the
button.
◆ The air conditioner runs in the Auto mode.
◆ The Auto mode cools the room depending on the set temperature.
Note
You can change modes at any time.
3 Press the
button to adjust the temperature until the required
temperature is displayed.
You can set the temperature between 16°C and 30°C.
Result:
◆ Each time you press the
button:
- The temperature is adjusted by 1°C
- The indoor unit beeps
◆ The fan speed is adjusted automatically.
◆ 2 fan speed indicators increase and decrease continuously and
turn round.
Control Panel
E-9
Selecting the Cool Mode
You can select the Cool mode if you want to cool your room.
You can adjust the temperature and the fan speed when cooling.
1
If necessary, press the
Result:
2 Press the
3
button on the remote control until
is displayed.
Result:
◆ The indoor unit beeps each time you press the
◆ The air conditioner runs in the Cool mode.
Note
You can change modes at any time.
button.
Press the
button to adjust the temperature until the required
temperature is displayed.
You can set the temperature between 16°C and 30°C.
Result:
4
(On/Off) button.
◆ The operation indicator on the indoor unit lights up.
◆ The air conditioner starts up in the mode you selected last.
◆ The indoor unit beeps.
◆ Each time you press the
button:
- The temperature is adjusted by 1°C
- The indoor unit beeps
◆ If the room temperature is higher than the selected
temperature, the air conditioner starts cooling.
◆ If the room temperature reaches the set temperature, the air
conditioner stops cooling, but the fan operates consistently.
Press the
button to select the fan speed until the required setting
is displayed.
Automatic (rotated :
)
Low
Medium
High
Result:
◆ Each time you press the
button, the indoor unit beeps.
◆ The fan speed indicator increases and decreases
continuously and turns round each time you press
the
button.
Control Panel
Note
5
E-10
The fan speed indicator of the indoor unit varies according to
the temperature in the Automatic fan speed.
To control the airflow direction, refer to pages 18 and 19.
Selecting the Dry Mode
You can select the Dry mode if you want to dehumidify your room.
You can adjust the temperature in this mode.
1
If necessary, press the
Result:
2
3
Press the
button on the remote control until
is displayed.
Result:
◆ The indoor unit beeps each time you press the
◆ The air conditioner runs in the Dry mode.
Note
You can change modes at any time.
button.
Press the
button to adjust the temperature until the required
temperature is displayed.
You can set the temperature between 18°C and 30°C.
Result:
4
(On/Off) button.
◆ The operation indicator on the indoor unit lights up.
◆ The air conditioner starts up in the mode you selected last.
◆ The indoor unit beeps.
◆ Each time you press the
button:
- The temperature is adjusted by 1°C
- The indoor unit beeps
◆ The air conditioner starts dehumidifying and the fan
speed is adjusted automatically.
To control the airflow direction, refer to pages 18 and 19.
E-11
Selecting the Fan Mode
You can select the Fan mode if you want to ventilate your room. It helps to
refresh the air in your room. You can adjust the fan speed in this mode.
1
If necessary, press the
Result:
2
3
Press the
(On/Off) button.
◆ The operation indicator on the indoor unit lights up.
◆ The air conditioner starts up in the mode you selected last.
◆ The indoor unit beeps.
button on the remote control until
is displayed.
Result:
◆ The indoor unit beeps each time you press the
◆ The air conditioner runs in the Fan mode.
◆ The temperature is set automatically.
Note
You can change modes at any time.
button.
Press the
button to select the fan speed until the required setting
is displayed.
Low
Medium
High
Result:
◆ Each time you press the
button, the indoor unit beeps.
◆ The fan speed indicator increases and decreases
continuously and turns round each time you press
the
button.
Control Panel
4
E-12
To control the airflow direction, refer to pages 18 and 19.
Selecting the Turbo Function
You can select the Turbo Function if you want to cool your room in
the fastest way. After the 30 - minute operation with the maximum
setting, it returns to the previous setting.
1
If necessary, press the
Result:
2
Press the
Result:
(On/Off) button.
◆ The operation indicator on the indoor unit lights up.
◆ The air conditioner starts up in the mode you selected last.
◆ The indoor unit beeps.
button.
◆ The temperature and fan settings are adjusted automatically.
◆ The fan speed indicator turns round with the maximum setting
and speed.
◆ The air conditioner cools the room as quickly as possible.
◆ After 30 minutes, the air conditioner is reset automatically to the
previous setting.
◆ You can select the Turbo function in the Auto, Cool mode.
If you select this function in the Dry or Fan mode, the mode
changes to the Auto mode.
Control Panel
3
Press the
button again to stop the Turbo Function before the end of the
30-minute period.
Result:
4
The air conditioner is reset automatically to the previous setting.
To control the airflow direction, refer to pages 18 and 19.
E-13
Selecting the Energy Saving Function
You can select the Energy Saving Function to save energy when
cooling. The temperature range decreases in order to perform this
function.
1
If necessary, press the
Result:
2
3
Press the
◆
◆
◆
◆
Note
You can select the Energy saving function only in the Cool
mode.
E-14
The indoor unit beeps.
The air conditioner runs in the Energy saving function.
The outer airflow blade moves up and down.
To stop the Energy saving function, press the
again.
Press the
button to adjust the temperature until the required
temperature is displayed. You can set the temperature between 26°C
and 30°C.
If you want to adjust temperature under 26°C, cancel the
Energy saving function before adjusting the temperature.
Press the
button to select the fan speed until the required
setting is displayed.
Note
5
button.
Result:
Note
4
(On/Off) button.
◆ The operation indicator on the indoor unit lights up.
◆ The air conditioner starts up in the mode you selected last.
◆ The indoor unit beeps.
The fan speed indicator increases and decreases
continuously and turns round each time you press
the
button.
To control the airflow direction, refer to pages 18 and 19.
Selecting the Auto Cleaning Function
You can select the Auto Cleaning Function if you want to sterilize
the air conditioner or remove mold. Even when the air conditioner is
turned off, you can set this function.
1
If necessary, press the
Result:
2
Press the
Result:
(On/Off) button.
◆ The operation indicator on the indoor unit lights up.
◆ The air conditioner starts up in the mode you selected last.
◆ The indoor unit beeps.
button.
◆ The
indicator on the indoor unit lights up and the
Auto Cleaning function is set.
◆ When you turn the air conditioner off, it operates the
Auto Cleaning function for 30 minutes.
After 30 minutes, the air conditioner turns off.
Remote Control
◆ If you press the
button when the air conditioner is
turned off, the air conditioner operates the Auto Cleaning
Function for 30 minutes.
When the air conditioner
is turned
On
Off
Note
3
Mode
Operating time
Auto, Cool, Dry
30 minutes
Fan
15 minutes
30 minutes
Control Panel
The Auto Cleaning indicator is displayed only on the indoor unit.
Press the
button again to stop the Auto cleaning function before
the end of the 30-minute period.
E-15
Selecting the Sound On / Off Function
You can turn on or off the sound of the air conditioner with the remote control.
1
Press the
Note
button to turn off the sound.
Each time you press the
selected repeatedly.
On
Off
E-16
button, Sound On/Off function is
Selecting the Anions Function
The air conditioner can generate anions with an ionizer in the indoor
unit. Since it is an additional function, you can select it in any mode,
even when the air conditioner is turned off.
1
Press the
Result:
button.
◆ The air conditioner generates anions.
◆ The indoor unit beeps.
Note
If you press the
button when the air conditioner is off,
the air conditioner turns on automatically and generates
anions in the Fan mode with Low fan speed.
2
Press the
button again to stop the Anions function.
Result: The air conditioner is reset automatically to the previous mode,
temperature and fan settings.
3
To control the airflow direction, refer to pages 18 and 19.
E-17
Adjusting the Airflow Direction Vertically
You can adjust the airflow direction vertically. The outer airflow
blade moves up and down to increase the efficiency of the cooling
operation.
1
Press the
Result:
2
Press the
button again to move the blade up and down
automatically during operation.
3
Press the
Note
E-18
button until the required direction is set.
The outer blade is adjusted vertically.
button again to stop the blade moving up and down.
If you turn the air conditioner...
Then the blade...
Off
is closed completely.
On
set to the default position.
Adjusting the Airflow Direction Horizontally
You can adjust the airflow direction horizontally manually.
The inner blades with small fins moves the air in the required
direction.
1
Adjust the inner blades by moving them to left or right.
E-19
Setting the On Timer
You can set the On Timer to turn on the air conditioner automatically
at the appointed time. You can set the time from 30 minutes to 24 hours.
1
Press the
button until the required time is displayed to set the
On Timer. You can set the time between 0.5 hour and 24 hours.
2
Press the
Result:
3
button to complete the setting.
◆ The remaining time is displayed.
◆ The timer indicator stops blinking.
◆ The selected mode and the temperature on the display
disappear after 10 seconds.
◆ The air conditioner turns on automatically at the appointed
time and the On Timer setting disappears.
Press the
button until the desired mode is displayed at the top of the
remote control to select the mode in advance.
Result:
The air conditioner operates in the selected mode when it is
turned on.
To Cancel the On Timer
Press the
Note
E-20
button to cancel the On Timer.
If you press the
button, both the On Timer and the Off
Timer are canceled.
Setting the Off Timer
You can set the Off Timer to turn off the air conditioner automatically
at the appointed time. You can set the time from 30 minutes to 24 hours.
1
Press the
button until the required time is displayed to set the
Off Timer. You can set the time between 0.5 hour and 24 hours.
2
Press the
Result:
button to complete the setting.
◆ The remaining time is displayed.
◆ The timer indicator stops blinking.
◆ The air conditioner turns off automatically at the appointed
time and the Off Timer setting disappears.
Example If you would like to turn the air conditioner on after 2 hours
and to operate it for 2 hours:
Note
1. Press the
button until ‘2.0 Hr’ is displayed.
2. Press the
button.
3. Press the
button until ‘4.0 Hr’ is displayed.
4. Press the
button.
You can check or change the mode and/or the temperature by
pressing the
button or the
button after setting the
Off Timer.
To Cancel the Off Timer
Press the
Note
button to cancel the Off Timer.
If you press the
are canceled.
button, both the On Timer and the Off Timer
E-21
Setting the Sleep Timer
You can set the Sleep Timer to turn off the air conditioner automatically
while you are sleeping. The air conditioner stops operating 6 hours after
you set the Sleep Timer.
1
Press the
button.
Result:
◆ The indoor unit beeps.
◆ The air conditioner will be controlled as indicated in the
illustrations below.
Note
You can set Sleep Timer only in the Cool mode.
Cooling
The set temperature is
increased by 1°C every hour.
After the increase of 2°C, the
temperature is maintained
for 4 hours.
To Cancel the Sleep Timer
Press the
Result:
E-22
button to cancel the Sleep Timer.
◆ The indoor unit beeps.
◆ The
indicator is no longer displayed.
◆ The air conditioner operates normally.
Operating Recommendations
When you use your air conditioner, it is recommended to read the
following :
Topic
Recommendation
Power failure
If power failure occurs when the air conditioner
is operating, the air conditioner turns off.
When the power returns, the air conditioner
starts up again automatically.
Protection mechanism
When the air conditioner is started immediately
after being plugged in or stopped, the normal
operation starts up after 3 minutes for the
reason of protection.
E-23
Temperature and Humidity Ranges
If you check the following tables, you can use your air conditioner more efficiently.
If the air conditioner is used at...
Then...
High temperatures
The air conditioner may stop operating for the reason of protection.
Low temperatures
Water may leak and some malfunction may occur if the heat exchanger freezes.
High humidity levels
Water may condense and drip from the surface of the indoor unit if you don’t use
the air conditioner for a long time.
Operation
Outdoor Temperature
Indoor Temperature
Indoor Humidity
Cooling
Dehumidifying
21°C to 43°C approx.
18°C to 43°C approx.
16°C to 32°C approx.
16°C to 32°C approx.
80% or less
-
❇
E-24
If you use the air conditioner over 32°C(indoor temperature), the cooling capacity may drop.
Operating Your Air Conditioner Without the Remote Control
You can operate your air conditioner directly without the remote control.
1
Open the front grille.
2
To turn the air conditioner on, press the On/Off button in the front grille
of the indoor unit.
Result:
3
◆
◆
The Operation indicator on the indoor unit lights up.
The indoor unit beeps.
To turn the air conditioner off, press the On/Off button again.
Note
Even if you turned the air conditioner on with the On/Off button,
you can control it with the remote control.
E-25
Troubleshooting Guide
Before contacting the service center, check the following. It will save your time and the
expense of an unnecessary call.
Problem
E-26
Explanation/Solution
The air conditioner does not
operate.
◆ Check if the circuit breaker of the air conditioner is switched on.
◆ Check if the air conditioner is turned on. If necessary, press the
(On/Off) button on the remote control.
◆ Check if the Timer indicator on the indoor unit is on.
If so:
- Wait until the set time is reached and the air conditioner starts
automatically.
- Cancel the Timer. (See pages 20 and 21 for further details)
The air conditioner does not
operate with the remote control.
◆ Check if there are no obstacles in front of the indoor unit.
◆ Check the remote control batteries.
◆ Make sure that you are within 7 meters from the indoor unit.
No beep is heard when you press
the
(On/Off) button on the
remote control.
◆ Check if you are pointing the remote control at the remote control
sensor on the right side of the indoor unit.
◆ Replace the remote control batteries if necessary.
The air conditioner does not cool.
◆ Check if the correct operating mode has been selected
(Auto, Cool).
◆ The room temperature may be too low.
◆ Check if the air filter is dirty; refer to page 27 for cleaning instructions.
◆ Check that there is no obstacle in front of the outdoor unit.
The fan speed does not change
when you press the
button.
◆ Check if the mode is set to the Cool or Fan mode;
in the Auto and Dry mode, the fan speed changes automatically.
The airflow direction does not
change when you press the
button.
◆ Check if the air conditioner has been turned on; if necessary, press
the
(On/Off) button on the remote control.
The timer is not correctly triggered.
◆ Check if the timer is set correctly; see pages 20 and 21.
Odor permeates into the
room during operation.
◆ You can use the Fan mode to ventilate your room.
Cleaning Your Air Conditioner
For the best use of your air conditioner, you must clean it every 2 weeks
to remove the dust that accumulates on the air filter.
IMPORTANT
Before cleaning your air conditioner, check if you have
turned off the circuit breaker.
1
Open the front grille by pulling on the tabs on the lower right and left
sides of the indoor unit.
2
Detach the front grille by pulling it forwards.
3
Hold the edge of the air filter under the front grille and pull to release.
4
Remove all dust on the air filter with a vacuum cleaner or brush.
5
When you finish, insert the top of the filter into the slot and fix it to
5 tabs of the grille.
6
Clean the front grille with a damp cloth and mild detergent
(do NOT use benzene, solvents or other chemicals).
7
Reassemble the air filter and the front grille.
Note
If you have not used the air conditioner for a long time, select the
Fan mode for 3 to 4 hours to dry the inside of the air conditioner.
Front grille
Body groove
Body
Air filter
Body
Front grille
Hook
❄ The design and shape are subject
to change according to the model.
Cleaning Anti-Allergy and Deodorizing Filter (Option)
There are Anti-Allergy and Deodorizing filters inside your air conditioner.
They remove odours and dust in your room. You should clean the filters
every 3 months.
1
Open the upper front grille by pulling the lower right and left tabs of
the grille.
2
Pull out the Anti-Allergy and Deodorizing filter.
3
Wash the filters with clean water, then dry them in the shade.
4
Insert the filters in their place.
5
Close the front grille.
Deodorizing Filter Anti-Allergy Filter
E-27
THIS AIR CONDITIONER IS MANUFACTURED BY:
ELECTRONICS
Printed in Korea
Download PDF

advertising