Samsung | RF67DEPN | Samsung RF70 מקרר 3 דלתות דגם נפח כללי 594 ליטר User guide

Refrigerator
user manual
English
Free Standing Appliance
imagine the possibilities
Thank you for purchasing a Samsung product.
To receive a more complete service,
please register your product at
www.samsung.com/register
DA68-1868U-13
safety information
SAFETY INFORMATION
• Before operating the appliance, please read this
manual thoroughly and retain it for your reference.
• Use this appliance only for its intended purpose
as described in this instruction manual. This
appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
• Warnings and Important Safety Instructions in this
manual do not cover all possible conditions and
situations that may occur. It is your responsibility
to use common sense, caution, and care when
installing, maintaining, and operating your
appliance.
• Because these following operating instructions
cover various models, the characteristics of your
freezer may differ slightly from those described in
this manual.
Important safety symbols and
precautions:
WARNING
CAUTION
Hazards or unsafe practices that may
result in severe personal injury or
death.
Hazards or unsafe practices that may
result in minor personal injury or
property damage.
After reading this section, keep it in a safe place
for future reference.
SEVERE WARNING SIGNS
FOR TRANSPORTATION AND
WARNING SITE
• When transporting and installing the
appliance, care should be taken to ensure
that no parts of the refrigerating circuit are
damaged.
- Refrigerant leaking from the pipe work could
ignite or cause an eye injury. If a leak is detected,
avoid any naked flames or potential sources of
ignition and air the room in which the appliance is
standing for several minutes.
• In order to avoid the creation of a flammable
gas-air mixture if a leak in the refrigerating
circuit occurs, the size of the room in which the
appliance may be sited depends on the amount
of refrigerant used.
• Never start up an appliance showing any signs
of damage. If in doubt, consult your dealer. The
room where the refrigerator will be sited must
be 1m³ in size for every 8g of R600a refrigerant
inside the appliance. The amount of refrigerant
in your particular appliance is shown on the
identification plate inside the appliance.
WARNING
Do NOT attempt.
Do NOT disassemble.
Do NOT touch.
Follow directions carefully.
Unplug the power plug from the wall
socket.
Make sure the machine is grounded to
prevent electric shock.
Call the contact center for help.
-
•
•
-
Note.
These warning signs are here to prevent injury to
you and others.
Please follow them explicitly.
02_ safety information
•
-
SEVERE WARNING SIGNS
FOR INSTALLATION
• Do not install the refrigerator in a damp
place or place where it may come in
contact with water.
Deteriorated insulation of electrical parts may
cause an electric shock or fire.
Do not place this refrigerator in direct sunlight or
expose to the heat from stoves, room heaters or
other appliance.
Do not plug several appliances into the same
multiple power board.
The refrigerator should always be plugged into
its own individual electrical which has a voltage
rating that matched the rating plate.
This provides the best performance and also
prevents overloading house wiring circuits, which
could cause a fire hazard from overheated wires.
If the wall socket is loose, do not insert the power
plug.
There is a risk of electric shock of fire.
• Do not use a cord that shows cracks or abrasion
damage along its length or at either end.
• Do not bend the power cord excessively or place
heavy articles on it.
• Do not use aerosols near the refrigerator.
- Aerosols used near the refrigerator may cause an
explosion or fire.
•
-
•
•
-
•
• This refrigerator must be properly installed
and located in accordance with the manual
before it is used.
Connect the power plug in proper position with
the cord hanging down.
If you connect the power plug upside down, wire
can get cut off and cause fire or electric shock.
Make sure that the power plug is not squashed
or damaged by the back of the refrigerator.
When moving the refrigerator, be careful not to
roll over or damage the power cord.
This constitutes a fire hazard.
The appliance must be positioned so that the
plug is accessible after installation.
• The refrigerator must be grounded.
- You must ground the refrigerator to
prevent any power leakages or electric
shocks caused by current leakage from
the refrigerator.
• Never use gas pipes, telephone lines or other
potential lightening rods as ground.
- Improper use of the ground plug can result in
electric shock.
• If the power cord is damaged, have it
replaced immediately by the manufacturer
or its service agent.
• The fuse on the refrigerator must be changed by
a qualified technician or service company.
- Failing to do so may result in electric shock or
personal injury.
CAUTION SIGNS FOR
CAUTION INSTALLATION
• Keep ventilation opening in the appliance
enclosure or mounting structure clear of
obstruction.
• Allow the appliance to stand for 2 hours after
installation.
WARNING
SEVERE WARNING SIGNS
FOR USING
• Do not insert the power plug with wet
hands.
• Do not store articles on the top of the appliance.
- When you open or close the door, the articles
•
-
•
-
•
-
•
-
•
-
•
-
•
•
-
•
-
•
•
•
•
•
•
-
may fall and cause personal injury and/or material
damage.
Do not put items filled with water on the
refrigerator.
If spilled, there is a risk of fire or electric shock.
Do not let children hang on the door.
Failure to do so may cause serious personal
injury.
Do not leave the doors of the refrigerator open
while the refrigerator is unattended and do not let
children enter inside of the refrigerator.
There is a risk of children entrapment and serious
personal injury because of low temperature.
Never put fingers or other objects into the
dispenser hole.
Failure to do so may cause personal injury or
material damage.
Do not store volatile or flammable substances
such as benzene, thinner, alcohol, ether or LP
gas in the refrigerator.
The storage of any of such products may cause
explosions.
Do not store low temperature-sensitive
pharmaceuticals products, scientific materials or
other low temperature-sensitive products in the
refrigerator.
Products that require strict temperature controls
must not be stored in the refrigerator.
Do not place or use electrical appliance inside
the refrigerator, unless they are of a type
recommended by the manufacturer.
Do not use a hair dryer to dry the inside of the
refrigerator. Do not place a lighted candle in the
refrigerator for removing bad odors.
This may result in electric shock or fire.
Do not touch the inside walls of the freezer or
products stored in the freezer with wet hands.
This may cause frostbite.
Do not use mechanical devices or any other
means to accelerate the defrosting process, other
than those recommended by the manufacturer.
Do not damage the refrigerant circuit.
• This product is intended only for the
storage of food in a domestic environment.
Bottles should be stored tightly together so that
they do not fall out.
If a gas leak is detected, avoid any naked flames
or potential sources of ignition and air the room
in which the appliance is standing for several
minutes.
Use only the LED Lamps provided by
manufacturer or service agents.
Children should be supervised to ensure that they
do not play with and/or climb into the appliance.
Keep fingers out of “pinch point” areas :
clearances between the doors and cabinet are
necessarily small. Be careful when you open the
doors when children are in the area.
safety information _03
• Do not disassemble or repair the
refrigerator by yourself.
- You run risk of causing a fire, malfunction and/
or personal injury. In case of malfunction, please
contact your service agents.
-
•
•
-
•
-
• If the appliance generates a strange noise,
a burning or smell or smoke, unplug the
power plug immediately and contact your
nearest service center.
Failing to do so may result in electric or fire
hazards. Keep ventilation opening in the
appliance enclosure or mounting structure clear
of obstruction.
If you experience difficulty when changing the
light, contact service agents.
If the products equipped with LED Lamp, do
not disassemble Lamp Cover and LED Lamp by
yourself.
Please contact your service agents.
If any dust or water is in refrigerator, pull
out power plug and contact your Samsung
Electronics service center.
There is a risk of fire.
CAUTION
-
•
-
•
-
•
-
-
•
CAUTION SIGNS FOR USING
• To get best performance of product,
- Do not place foods too closely in front of
the vents at the rear of the appliance as
it can obstruct free air circulation in the
refrigerator compartment.
Wrap the food up properly or place it in airtight
containers before put it into the refrigerator.
Do not place carbonated or fizzy drinks in the
freezer compartment. Do not put bottles or glass
containers in the freezer.
When the contents freeze, the glass may break
and cause personal injury and property damage.
Do not change the functionality of or modify the
refrigerator.
Changes or modifications may result in personal
injury and/or property damage. Any changes or
modifications performed by a 3rd party on this
completed appliance is neither covered under
Samsung warranty service, nor is Samsung
responsible for safety issues and damages that
result from 3rd party modifications.
Do not block air holes.
If the air holes are blocked, especially with a
plastic bag, the refrigerator can be over cooled. If
this cooling period lasts too long, the water filter
may break and cause water leakage.
Do not put any newly introduced food for freezing
near to already food.
Please observe maximum storage times and
expiry dates of frozen goods.
04_ safety information
• Fill water tank, ice tray, water cubes only with
potable water.
• Use only the ice maker provided with the
refrigerator.
• The water supply to this refrigerator must only be
installed/connected by a suitably qualified person
and connect to a potable water supply only.
• In order to operate the ice maker properly, water
pressure of 138 ~ 862kpa(1.4~8.8kgf/cm3) is
required.
CAUTION SIGNS
FOR CLEANING AND
CAUTION MAINTENANCE
• Do not directly spray water inside or
outside the refrigerator.
- There is a risk of fire or electric shock.
• Do not spray inflammable gas near the
refrigerator.
- There is a risk of explosion or fire.
• Do not spray cleaning products directly on the
display.
- Printed letters on the display may come off.
• Remove any foreign matter or dust from the
power plug pins. But do not use a wet or damp
cloth when cleaning the plug, remove any foreign
material or dust from the power plug pins.
- Otherwise there is a risk of fire or electric shock.
• Never put fingers or other objects into the
dispenser hole and ice chute.
- It may cause personal injury or material damage.
• Use a clean sponge or soft cloth and a mild
detergent in warm water to clean the refrigerator.
• Do not use abrasive or harsh cleansers
such as window sprays, scouring cleansers,
flammable fluids, muriatic acid, cleaning waxes,
concentrated detergents, bleaches, or cleansers
containing petroleum products on exterior
surfaces (doors and cabinet), plastic parts, door
and interior liners, and gaskets.
- These can scratch or damage the material.
• Do not clean glass shelves or covers with
warm water when they are cold. Glass shelves
and covers may break if exposed to sudden
temperature changes or impacts such as
bumping or dropping.
• Unplug the refrigerator before cleaning and
performing maintenance.
WARNING
SEVERE WARNING SIGNS
FOR DISPOSAL
• Ensure that none of the pipes on the back
of the appliance are damaged prior to
disposal.
• R600a or R134a is used as a refrigerant. Check
the compressor label on the rear of the appliance
or the rating label inside the refrigerator to see
which refrigerant is used for your refrigerator.
When this product contains flammable gas
(Refrigerant R600a), contact your local authority
in regard to safe disposal of this product.
Cyclopentane is used as a insulation blowing gas.
The gases in insulation material require special
disposal procedure. Please contact your local
authorities in regard to the environmentally safe
disposal of this product. Ensure that none of the
pipes on the back of the appliances are damaged
prior to disposal. The pipes shall be broke in the
open space.
• If the appliance contains iso-butane refrigerant
(R600a), a natural gas with high environmental
compatibility that is, however, also combustible.
When transporting and installing the appliance,
care should be taken to ensure that no parts of
the refrigerating circuit are damaged.
• When disposing of this product or other
refrigerators, remove the door/door seals, door
latch so that small children or animals cannot
become trapped inside. Leave the shelves in
place so that children may not easily climb inside.
Children should be supervised to ensure that they
do not play with the old appliance.
• Please dispose of the packaging material for this
product in an environmentally friendly manner.
ADDITIONAL TIPS FOR
PROPER USAGE
• In the event of a power failure, call the local office
of your Electricity Company and ask how long it
is going to last.
- Most power failures that are corrected within
an hour or two will not affect your refrigerator
temperatures. However, you should minimize the
number of door openings while the power is off.
- Should the power failure last more than 24 hours,
remove all frozen food.
• If keys are provided with the refrigerator, the keys
should be kept out of the reach of children and
not in vicinity of the appliance.
• The appliance might not operate consistently
(possibility of temperature becoming too warm
in refrigerator) when sited for an extended period
of time below the cold end of the range of
contents
•
•
•
•
•
temperature for which the refrigerating appliance
is designed.
Do not store food which spoils easily at low
temperature, such as bananas, melons.
Your appliance is frost free, which means there is
no need to manually defrost your appliance, as
this will be carried out automatically.
Temperature rising during the defrost can comply
with ISO requirement. But if you want to prevent
an undue rise in the temperature of the frozen
food while defrosting the appliance, please wrap
the frozen food in several layers of newspaper.
Any increase in temperature of frozen food during
defrosting can shorten its storage life.
Do not keep vegetable oil in your refrigerator’s
door bins. The oil can solidify, making it foultasting and difficult to use. In addition, the open
container can leak and the leaked oil can cause
the door bin to crack. After opening an oil
container, it is best to keep the container in a cool
and shaded place such as a cupboard or pantry.
- Examples of vegetable oil: olive oil, corn oil,
grape-seed oil, etc.
Saving Energy Tips
- Install the appliance in a cool, dry room with
adequate ventilation.
Ensure that it is not exposed to direct sunlight
and never put it near a direct source of heat
(radiator, for example).
- Never block any vents or grilles on the appliance.
- Allow warm food to cool down before placing it in
the appliance.
- Put frozen food in the refrigerator to thaw.
You can then use the low temperatures of the
frozen products to cool food in the refrigerator.
- Do not keep the door of the appliance open for
too long when putting food in or taking food out.
The shorter time for which the door is open, the
less ice will form in the freezer.
- Clean the rear of the refrigerator regularly. Dust
increases energy consumption.
- Do not set temperature colder than necessary.
- Ensure sufficient air exhaust at the refrigerator
base and at the back wall of the refrigerator.
Do not cover air vent openings.
- Allow clearance to the right, left, back and top
when installing.
This will help reduce power consumption and
keep your energy bills lower.
SETTING UP YOUR FREEZER …………………………………………………………………………………… 06
OPERATING YOUR SAMSUNG REFRIGERATOR……………………………………………………………… 15
TROUBLESHOOTING……………………………………………………………………………………………… 19
safety information _05
setting up your freezer
GETTING READY TO INSTALL
THE REFRIGERATOR
Congratulations on your purchase of this Samsung
Refrigerator. We hope you enjoy the state-of-art
features and efficiencies that this new appliance
offers.
When moving your refrigerator
CAUTION
To prevent floor damage be sure the front
leveling legs are in the up position(above the
floor). Refer to ‘Adjusting the doors’ in the
manual (on page 13)
Selecting the best location for the
Refrigerator
150mm
150mm
100mm
100mm
Flat-blade
screwdriver(-)
FLOORING
100mm
100mm
•
•
•
•
A location with easy access to the water supply.
A location without direct exposure to sunlight.
A location with level (or nearly level) flooring.
A location with enough space for the Refrigerator
doors to open easily.
• Allow sufficient space to the right, left, back and
top for air circulation. If the Refrigerator does not
have enough space, the internal cooling system
may not work properly.
• Please ensure that appliance can be moved freely
in the event of maintenance & service.
First thing! Make sure that you can easily move
your Refrigerator to its final location by measuring
doorways (both width and height), thresholds,
ceilings, stairways, etc.
817mm
817mm
817mm
665mm
RF62* : 1172mm
RF67* : 1222mm
1492mm
RF62* : 1125mm
RF67* : 1175mm
RF62*:1455mm
RF67*:1505mm
1492mm
Drawer-Type
Swing-Type
• Allow clearance to the right, left, back and
top when installing. This will help reduce
power consumption and keep your energy
bills lower.
• If you install the Refrigerator where is below 10ºC,
it may not function in optimum level.
• Do not locate the refrigerator where the wet
condition.
06_ setting up
Control Lever
For proper installation, this refrigerator must be
placed on a level surface of hard material that is the
same height as the rest of the flooring. This surface
should be strong enough to support a fully loaded
refrigerator, or approximately 106kg.
To protect the finish of the flooring, cut a large
section of the cardboard
carton and place under
the refrigerator where
you are working. When
moving the refrigerator,
be sure to pull it straight
out and return it to
position by pushing it
straight in.
INSTALLATION OF THE WATER
LINE (AUTO ICE MAKER
MODEL)
Before you install the water line
• The water line installation is not warranted by the
refrigerator manufacturer.
So before you install the water line, read the
whole steps for installing and follow these
instructions carefully to minimize the risk of
expensive water damage.
• Banging pipes (water banging in the pipes) in
house plumbing can cause damage to fridge
parts and lead to water leakage or flooding. Call
a qualified plumber to correct the problem before
installing the water supply line to the fridge.
Check the accessories listed
below.
Water line fixer and screws
Pipe connector
Water line
Fastner
-
Refer to ‘MAKING MINOR
ADJUSTMENTS BETWEEN
DOORS’(on page 14)
Using the water filter (not provided)
Connecting to water supply line
• Shut off the main water
supply line and turn the Ice
maker to the off position.
• Locate the nearest cold
drinking water line.
• Follow the instructions in the
water filter installation kit.
• After connecting the water
supply line to the Cartridge
Holder inlet and installing the
Filter Cartridge (insert plastic
line in fully).
• Turn on water supply and
flush 3L into a bucket to clear
the water filter.
• The water filter must be installed outside the
refrigerator.
It is not provided with your new
refrigerator. The filter cartridge (8)
and holder (9) kit can be purchased
Incorrect
from the retailer where you
purchased this refrigerator.
• Do not use copper line.
• Cut the tubing, making sure the
ends are square and clean.
Correct
Connect the water line to the fridge
• Connect the plastic line
on the back of your
fridge to the cartridge
holder outlet (fully insert
the plastic line to the
cartridge holder outlet).
• Insert plastic clip to the
cartridge holder inlet and
outlet.
• Turn water on and check
for any leakage.
Cartridge Holder
Clip
Plastic line
(Provided)
Filter
cartridge
• You can purchase the necessary filter
cartridge at the retailer where you
purchased this refrigerator. Make sure
you buy the SAMSUNG filter cartridge
(Replacement cartridge No : DA2910105J) to ensure the best performance.
• Water line must be connected to drinkable water
only
• A compression fitting and nut kit is supplied with
the unit and it is inside the fridge drawer.
• When pushing the Refrigerator back, make sure
you don’t roll over the power cord or water line
(Icemaker supply line)
To use without the water filter
section
Connecting to the water supply line
90 degree
1.
2.
3.
4.
5.
6.
7.
8.
9.
Cold Water line
Pipe Clamp.
Plastic line
Compression Nut
Compression Sleeve
Packing Nut
Shut Off Valve
Filter Cartridge
Cartridge Holder
• Shut off the main water
supply line and turn the Ice
maker to the off position.
• Locate the nearest cold
water drinking line.
1.
2.
3.
4.
5.
6.
7.
Cold Water line
Pipe Clamp.
Plastic line
Compression Nut
Compression Sleeve
Packing Nut.
Shut Off Valve
setting up _07
01setting up
• To prevent burns and product damage, do not
hook up the water line to the hot water line.
• Do not install the water line in areas where
temperatures fall below freezing.
• When using any electrical device (such as a
power drill) during installation, be sure the device
is insulated or wired in a manner to prevent
electric shock.
• All installations must be in a accordance with
local plumbing code requirements.
• Water line Kit and water filter are not
covered by Samsung’s Warranty. The
manufacturer (or dealer, installer) of them is
responsible for any defects and all the loss
caused by water filter & water line kit.
• The filter should be replaced according to
manufacturer (or dealer)’s instruction.
• To order additional water filters, please contact
the manufacturer (or dealer) of the filter.
1. First, shut off the main water supply line.
2. Locate the nearest cold, drinking water line.
3. Follow the Water line Installation Instructions in
the installation kit.
Only connect the water line to a drinkable
water source.
If you have to repair or disassemble the
water line, cut off 6.5mm of the plastic tubing
to make sure you get a snug, leak-free
connection.
CAUTION
The water line must be connected
to the cold water pipe. If it is
connected to the hot water
pipe, it may cause the purifier to
malfunction.
After the water supply has been installed
check all the joints to ensure there are no
leaks.
• Samsung Warranty does
not cover THE WATER
LINE INSTALLATION.
• The cost of the water
line installation is at the
customers expense, unless the retailer has
covered this expense in the delivery charge.
• Please contact a Plumber or Authorized Installer
for the installation if needed.
• If Water leakage occurs due to improper
installation, Please contact installer.
Close Main
Water pipe
Close Main
Water pipe
No gap
Connecting the water line to the
refrigerator
1. Remove the cap from water line on the unit and
insert compression nut to the water line on the
unit after disassembling from provided water line.
2. Connect both water line from the unit and water
line in the kit.
3. Tighten the compression nut onto the
compression fitting. There should be no gaps
between
(A, B & C )
4. Turn water on and check for any leakage.
Remove
cap
Loosen a
Water Line
from unit
No gap
Water Line
from unit
08_ setting up
CAUTION
SETTING UP THE
REFRIGERATOR
Now that you have your new Refrigerator installed in
place, you are ready to set up and enjoy the features
and functions of the appliance. By completing the
following steps, your Refrigerator should be fully
operational.
1. Place the Refrigerator in an appropriate location
with reasonable clearance between the wall and
the Refrigerator. Refer to installation instructions
in this manual. (P8. Selecting the best location for
the Refrigerator)
2. Once the Refrigerator is plugged in, make sure
the interior light comes on when you open the
doors.
3. Set the Temperature control to the coldest
temperature and wait for an hour. The Freezer
will get slightly chilled and the motor will run
smoothly.
4. After powering the Refrigerator, it will take a few
hours to reach the appropriate temperature. You
can store food and drinks in the Refrigerator after
the temperature is sufficiently cool.
Required Tools (Not provided)
REMOVING THE
REFRIGERATOR DOORS
Some installations require door/drawer removal to
transport the Refrigerator to its final location.
Phillips Head
Driver(+)
Flat Head Driver(-)
Socket Wrench
(10mm) (for bolts)
Do not remove the door/drawer if it is not needed.
Before removing the door/drawer make sure you
read following items.
Hex Wrench
(Ø5mm)
(for Mid hinge)
Hex wrench
(5/32 inch)
(for Mid hinge
shaft)
•
•
-
-
-
Disconnect power to the Refrigerator before
removing the door or drawer.
• Be careful not to drop, damage or scratch
the door/drawer while removing them.
Be careful not to get injured while removing the
door/drawer.
Reattach the door/drawer properly to avoid:
Moisture from air leakage.
Uneven door alignment.
Wasting energy due to improper door seal.
Disassembling the fridge door
WARNING
Be careful not to drop and scratch the fridge door while removing the fridge door!
Socket wrench
Top Table
1. Remove the 3 screws
holding down the top table
and remove it.
2. Disconnect electric wire on
the top of the refrigerator.
3. Remove the 3 hex bolts
that hold the hinge on the
top of the refrigerator with
the 10mm socket wrench.
4. Remove the screw that
holds the ground wire with
a philips screwdriver(+).
5. Separate the hinge from
the electric wire and
ground wire as shown
above.
6. Lift the door straight up to
remove. Be careful not to
drop and scratch the doors
while removing them.
setting up _09
01setting up
CAUTION
Disassembling the freezer door
Middle Hinge
1. Separate the cap on the
middle hinge.
2. Remove the screw attached to the left and right middle
hinges with a philips screwdriver(+).
Remove the 2 hex head bolts attached to the left and right
middle hinges with an allen wrench(Ø5mm).
(DRAWER TYPE)
3. After opening the Freezer
door, lift the drawer box.
4. Remove 4 hex head bolts
from both sides with a
socket wrench(10mm)
(SWING TYPE)
3. Remove the Middle Hinge
connected to the Freezer.
4. Lift up the freezer door
from the hinge.
Be careful not to drop and
scratch the freezer door.
Reassembleing the door
CAUTION
To reassemble the door, assemble parts in revers oder.
10_ setting up
5. Lift up the freezer door
from the rails. Be careful
not to drop and scratch
the freezer door.
How to reverse the door (OPTION)
Unplug the refrigerator or disconnect the power.
Refer to the page 9, 10 for disassembling the door.
Cap
Cover
1. Remove 2 screws.
2. Separate front leg Cover.
3. Separate the Cap of the
front leg Cover. (pull out
inside of Cap)
4. Insert the Cap on the other
side of the front leg Cover.
5. Remove 2 bolts of each
hinge with the 10mm
wrench.
6. Place them in front of each
side.
7. Separate low hinge shaft
by using 5/32” wrench and
disassemble low hinge leg
by turning it colockwise,
and then assemble the low
hinge by turning it over.
8. Reattach the former right
hinge on the left side and
the former left hinge on the
right side by using 2bolts.
9. Separate stopper by
removing 1 screw on the
right lower side of freezer
and assemble the stopper
on the left side by reversing
it.
10. The middle hinge for
reversing a door can be
found in the fridge.
11. Change the middle hinges
assembled at refrigerator
to the middle hinges in the
fridge with handles.
12. Use the black hinge
cap of the middle hinge
assembled at refrigerator.
Then place it at the bottom
of the left middle hinge
supplied separately.
Use the Flat-blade screwdriver(-).
setting up _11
01setting up
Cap
13. Place the hole in the
bottom of the freezer door
over the low hinge.
14. Replace the middle hinge connected to the freezer.
15. Insert and tighten the screw into the left and right middle
hinges with a philips screwdriver(+). Insert and tighten the 2
hex head bolts into the left and right middle hinges with an
allen wrench(Ø5mm).
16. Replace the cap on the middle hinge.
17. Place the hole in the
bottom of the left door
over the middle hinge.
18. Insert the left upper hinge
shaft into the hole on the
corner of the fridge door.
19. Insert the upper hinges
into the holes at the top of
the door.
Insert and tighten the 3
hex head bolts into the left
and right upper hinges with
a socket wrench(10mm).
20. Insert and tighten the
ground screw into the left
and right upper hinges with
a philips screwdriver(+).
21. Connect the electronic
wire on the top of the
refrigerator.
22. Position the top table in
place. Insert and tighten
the 3 screws into the
top table with a philips
screwdriver(+).
12_ setting up
ADJUSTING THE DOORS
CAUTION
After putting the doors back on the Refrigerator,
make sure the Refrigerator is level so that you can
make final adjustments.
If the Refrigerator is not level, it will not be possible
to get the doors perfectly even.
NO
YES
Clean the ice box if there are some small pieces of ice on the bottom.
Also it is possible to sweat in the refrigerator and ask
more energy bills.
For example, when the left side is lower than the
right side, insert a flat-blade screwdriver into a notch
on the left control lever, and turn it clockwise or
counter clockwise to level the door.
Throw away the coherent ice if the ice maker is not used for long time.
Set “Ice Off” for saving energy if the ice
maker will not be used for long time.
Turning it clockwise to raise the refrigerator and
counterclockwise to lower it.
For the left side is higher, do it with right lever.
CAUTION
If you want to buy and use a tool of shoveling
ice,put it into special place of ice box or take
it out.
Both control levers must be surely touching
the floor to avoid the possible personal injury
or property damage because of tipping.
When the left
side is higher.
When the left
side is lower.
Control Lever
Screwdriver(-)
Screwdriver(-)
YES
CAUTION
There is protective film on the surface of some
refrigerator models, which is used to protect the
refrigerator from scratches during transport. To avoid
static electricity, please peel off the protective film
slowly. If the protective film is not removed for a long
time, it may cause color shading of the steel plate.
CAUTION
Do not apply strong shock or excessive force onto
the surface of glass.
-Broken glass may result in a personal injury and/or
property damage.
setting up _13
01setting up
NO
MAKING MINOR ADJUSTMENTS
BETWEEN DOORS
Remember, a level Refrigerator is necessary for
getting the doors perfectly even. If you need
help, review the previous section on leveling the
Refrigerator.
When the left door
is lower than the
right door.
When you turn the hex wrench counterclockwise (
), the door will move up.
Only the left-door height is adjustable for
Swing-Type.
1. After adjusting the doors, please insert the
supplied fastener ( 5 ) using Pliers ( 6 ) in the gap
between the hinge-grommet ( 7 ) and the middle
hinge ( 8 ). The number of fasteners you’ll need to
insert depends on the gap.
Adjustment
part
When the left door
is higher than the
right door.
2 fastener are enclosed with the refrigerator.
The thickness of each fastener is 1.0mm.
Adjustment
part
1. Pull out the freezer drawer ( 1 ), then you can see
the middle hinge ( 2 ) .
2. Insert the hex wrench (4 mm) ( 3 ) into the shaft
( 4 ) of the middle hinge.
3. Please adjust the height by turning the hex
wrench ( 3 ) clockwise (
) or counterclockwise (
).
2
3
4
1
Caution: Please clamp the power cord into the
hook to prevent the power cord from being worn
or damaged when the refrigerator isn’t working
or being moved.
3
14_ setting up
operating your samsung
refrigerator
PARTS AND FEATURES
1
Fridge
When the Ice Off button is pressed, ice will not be
produced.
Use this function only when it is needed.
2
Power Freeze
Press the Power Freeze Button. (Refer to the
picture.)
- The power Freeze light on the display goes on
(see the arrow mark) and this function begins to
operate regardless of the set freezer temperature.
Press the Power Freeze Button again to cancel this
function.
- The light goes off and it operates at the set
freezer temperature again.
- The Power Freeze function operates for 72 hours
regardless of the set temperature.
option
This function must be activated before putting
large stuff in freezercompartment at least 24
hours before.
Freezer
3
Freezer
If you want to control the freezer temperature, follow
as below.
Drawer Type
Swing Type
USING THE CONTROL PANEL
1
2
3
4
5
6
Press the Freezer Button (Refer the picture)
- The temperature can be set in 1ºC interval
between -25ºC and -14ºC.
When selecting the temperature, the set temperature
is displayed initially for 5 seconds, then the actual
temperature is displayed.
(There may be slight difference between the set
temperature and displayed actual temperature,
but it will be corrected to the set temperature
automatically.)
operating _15
02operating
Use this page to become more familiar with the
parts and features of the Refrigerator.
Ice Off Button
- The Freezer temperature will change
depending on the number of door
openings, quantity of food, ambient
temperature, etc.
- The temperature display will blink when freezer
temperature increases due to frequent door
opening, keeping warm food, etc.
5
Power Cool
Press the Power Cool Button. (Refer to the picture.)
- The Power cool light on the display goes on
(see the arrow mark) and this function begins to
operate regardless of the set fridge temperature.
(Blinking will stop when the refrigerator reaches
normal temperature. If for some reason it does not
stop after a long period of time, contact a Samsung
service center.)
4
Fridge
If you want to control the fridge temperature, follow
as below.
Press the Fridge Button (Refer the picture)
- The temperature can be set in 1ºC interval
between 1ºC and 7ºC.
When selecting the fridge temperature, the set
temperature is displayed initially for 5 seconds, then
the actual temperature is displayed.
Press the Power Cool Button again to cancel this
function.
- The light goes off and it operates at the set fridge
temperature again.
The Power Cool function operates for 2 and a
half hours regardless of the set temperature.
6
E.Saver Button
Press the Energy Saver button for better energy
efficiency. If water drops appear on the doors, turn
the Energy Saver function off.
MAKING ICE
Auto Ice Maker Model
(There may be slight difference between the set
temperature and displayed actual temperature,
but it will be corrected to the set temperature
automatically.)
- The Fridge temperature will change
depending on the number of door
openings, quantity of food, ambient
temperature, etc.
- Temperature of each shelve or container in the
fridge may be different.
- The temperature display will blink when fridge
temperature is increases due to frequent door
opening, keeping warm food, etc.
(Blinking will stop when the refrigerator reaches
normal temperature. If for some reason it does not
stop after a long period of time, contact a Samsung
service center.)
Sabbath function
1. Press adjustment keys on freezing compartment
and refrigerating chamber simultaneously and hold
for 5 seconds for the Sabbath function.
2. In Sabbath function mode, press adjustment keys
on freezing compartment and refrigerating chamber
simultaneously and hold for 5 seconds to exit this
function.
16_ operating
The ice maker will produce 8 cubes per cycle approximately 100~130 cubes in a 24-hour period,
depending on freezer compartment temperature,
room temperature, number of door openings and
other use conditions. Throw away
the first few batches of ice to
allow the water line to clear. Be
sure nothing interferes with the
sweep of the feeler arm. When
the bin fills to the level of the
feeler arm, the icemaker will stop
producing ice.
After the icemaker has been turned on again, there
will be a time delay before the icemaker resumes
operation.
It is normal for several cubes to be joined together.
If ice is not used frequently, old ice cubes will
become cloudy, taste stale and shrink. So if you
don’t want to make ice, press the Ice Off button.
When “Ice making” function is selected,icemaking is priority, Then the temperature
of freezer will be lower than the setting
temperature. If you don’t need the “Ice
making” function,please press the button
of “Ice Off”. Failing to do so may cause noise.
Twist Ice Maker Model
1. Pull out the Ice-cube trays.
2. Fill trays up to the water level mark(arrow).
3. Put the Ice-cube trays back in position. And close
the freezer door.
4. Once the water has become frozen, turn the dials
on the Ice cube trays to empty Ice cubes into the
storage bin.
2
To remove - Pull the drawer out
to full extension.
Tilt up the front of
the drawer and pull
straight out.
To replace - Insert the drawer
into the frame rails
and push back into
place.
1
2
The drawers need to be removed before the
glass shelf above them can be lifted out.
3
To get the best energy efficiency of this
product, please leave all selves, drawers
and baskets on their original position like as
illustration in page 15
4
REMOVING AND RELOCATING
THE FRIDGE ACCESSORIES
REMOVING THE FREEZER
ACCESSORIES
1. Door Bins
1. Pull Out Drawer
To remove - Simply lift the bin up
and pull straight out.
To remove - Pull the drawer out to full extension.
Tilt up rear of drawer and lift straight
out. (Refer to picture 1 & 2)
To replace - S
lide it in above the
desired location and
push down until it
stops.
CAUTION
Injury may occur if the door bins are not firmly
inserted. Do not allow children to play with
bins. Sharp corners of the bins may cause
injury.
Open the freezer door fully and remove the drawer.
To replace - Place the drawer onto the rails by tilting
it up. Lower the drawer into place until it
is horizontal and slide the drawer in.
(Refer to picture 3)
1
2
3
1
2
3
Empty the bin before adjusting it.
Dust removal method -Remove the guard and wash
in water.
2. Fridge shelves
To remove - W
hen pulling out the
shelf, if it does not
slide out easily, lift it
up slightly and pull
out again.
To replace - W
hen pushing in the shelf, if it does not
slide in easily, lift it up slightly and push
in again.
The Glass shelves are heavy.
CAUTION
Use special care when removing them.
2. Freezer Drawer Bin
Swing-Type
To remove - Pull the drawer out
fully. Tilt up the rear
of the bin and lift it
out to remove.
1
To replace - Place the bin into the
rail assembly.
2
When replacing, place the drawer
bin holder into the hole of the rail
operating _17
02operating
1
3. Vegetable & Fruit Drawers
Drawer-Type
To remove the drawer - P
ull the drawer out fully. Tilt
up the rear of the bin and lift
it out to remove.
To relocate the drawer - P
lace the bin into the rail
assembly.
Getting water from the dispenser
Drawer
(RF67****)
CAUTION
Do not allow children to play with the
refrigerator, as they could injure themselves or
damage the refrigerator.
Do not sit on the Freezer door. The door may
break. Do not allow children to climb into the
Freezer basket.
WARNING
Do not put anything other than water in the
water tank.
• Do not put anything other than water in the water
tank.
• Fill with water up to 4.0L. If the water is filled up
above the mark, it can spill out when the door
opens and closes.
• Push the cap until you hear a click.
CAUTION
If you remove the divider to clean the basket
bin, you must reinstall the divider using 1
screw after cleaning to prevent children from
getting trapped inside the basket.
USING THE WATER DISPENSER
(OPTION)
You can easily obtain chilled water with the water
dispenser without opening the refrigerator door. In
addition, you can save electricity by reducing the
number of times the door is opened by more than
30%.
Place a glass underneath the water
outlet and push it gently against
the water dispenser lever with your
glass. Blue light will turn on when
you push the lever.
• Make sure the glass is in
line with the dispenser to prevent the water
from splashing out.
• Water dispenser may not be abailable depending
on the model.
When the water dispenser is not in
use, the following is recommended
Fix the water supply device tightly into the fixing
hole.
The door will not be closed automatically when the
water supply device is pulled out for a long time
because of cold leaking.
Filling the water tank
CLEANING THE REFRIGERATOR
You can fill the water with the water tank sitting
inside of the refrigerator or you can remove the
water tank to fill the water.
WARNING
Method 1
After opening the cap, Fill the water. If you pour the
water too fast, water may overflow.
Method 2
1. Release the lock on the both side of the water
tank to remove the lid on the water tank.
2. Fill the water in the water tank.
Do not use Benzene, Thinner or Clorox™ for
cleaning. They may damage the surface of the
appliance and can create a risk of fire.
Do not spray the refrigerator with water while
it is plugged in, as it may cause an electric
CAUTION shock. Do not clean the refrigerator with
benzene, thinner or car detergent for risk of
fire.
CHANGING THE INTERIOR
LIGHTS
Changing the LED Type Lighting
CAUTION
Do not disassemble or replace the LED type
Lighting.
To change the LED Type Lighting contact Samsung
service center or your authorized Samsung dealer.
18_ operating
troubleshooting
SOLUTION
The Refrigerator does
not work at all or it does
not chill sufficiently.
• Check that the power plug is properly connected.
• Is the temperature control on the display panel set to the correct
temperature?
Try setting it to a lower temperature.
• Is the refrigerator in direct sunlight or located near a heat source?
• Is the back of the refrigerator so close to the wall that air cannot keep
circulating? (Refer to page 10 for the best location.)
The food in the
Refrigerator is frozen.
• Is the temperature control on the display set to the correct
temperature?
Try setting it to a warmer temperature.
• Is the temperature in the room too low?
• Did you store the food too close to the air vent at the back of the
refrigerator? Move the food away from the air vent.
You hear unusual noise
or sounds.
• Check that the refrigerator is level and stable.
• Is the back of the refrigerator too close to the wall and therefore
keeping air from circulating?
• Was anything dropped behind or under the refrigerator?
• A “ticking” sound is heard from inside the refrigerator. It is normal and
occurs because various accessories are contracting or expanding
according to the temperature of the refrigerator interior.
• When the automatic ice maker is on, ice is made in the ice container.
After the ice is made, the container inverts and the ice falls into the
storage compartment and water flows through the water valve. These
operations cause noise at regular intervals, but that noise is normal.
The front corners and
horizontal hinged section
of the appliance are hot
and condensation is
occurring.
• Some heat is normal as anti-condensators are installed in the horizontal
hinged section of the refrigerator to prevent condensation.
• Is the refrigerator door ajar? Condensation can occur when you leave
the door open for a long time.
Ice Maker is not
producing ice.
• Did you wait for 12 hours after installation of the water supply line
before making ice?
• Is the water line connected and the shut-off valve opened?
• Did you manually stop the ice making function?
• Is the freezer temperature too warm? Try setting the freezer
temperature lower.
You hear water bubbling
in the Refrigerator.
• This is normal. The bubbling comes from the refrigerator coolant liquid
circulating through the refrigerator.
There is a bad smell in
the Refrigerator.
• Check for spoiled food.
• Foods with strong odors (for example, fish) should be tightly covered.
• Clean out your freezer periodically and throw away any spoiled or
suspicious food.
Frost forms on the walls
of the Freezer.
• Is the air vent blocked? Remove any obstructions so air can circulate
freely.
• Allow sufficient space between the foods stored for efficient air
circulation.
• Is the freezer drawer closed properly?
troubleshooting _19
04troubleshooting
PROBLEM
Ambient Room Temperature Limits
This fridge/freezer is designed to operate in ambient temperatures specified by its temperature
class marked on the rating plate.
Class
Symbol
Ambient Temperature range(°C)
Extended Temperate
SN
+10 to +32
Temperate
N
+16 to +32
Subtropical
ST
+16 to +38
Tropical
T
+16 to +43
NOTE: Internal temperatures may be affected by such factors as the location of the fridge/
freezer, ambient temperature and the frequency with which you open the door. Adjust
the temperature as required to compensate for these factors.
Download PDF

advertising